CHANGZHOU RATTM MOTOR CO.,LTD TB6560HQT4 v3 4 Axis Driver User manual

CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
TB6560HQT4-v3
4 AXIS DRIVER USER MANUAL
Catalogue
...........................................................................................................................................................1
1. Overview.................................................................................................................................... 2
2. TB6560AHQ advantag...............................................................................................................3
2.1、At low speed operation System Advantages.................................................................... 3
2.2、In high-speed operation System Advantages....................................................................3
3. TB6560T4V1 Driver Board Introduction...................................................................................4
4. TB6560T4V1connection drawing.............................................................................................. 5
5. The definition of interface pins.................................................................................................. 5
6. The setting of current,microstepping,decay mode......................................................................7
6.1、current setting...................................................................................................................7
1
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
6.2、microstepping setting....................................................................................................... 8
7. The connection of kinds of stepper motors................................................................................ 9
8. The connection of limit switch................................................................................................. 11
9. The connection of 4th expand axis............................................................................................ 12
10. The match between driver board and stepper motors................................................................12
11. MACH3software user introduction........................................................................................... 14
11.1、Mach3 software open................................................................................................... 14
11.2、mach3software basic setting.........................................................................................16
11.3、The limit switch setting in MACH3............................................................................. 19
11.4、Run of the G-code........................................................................................................ 20
1. Overview
The PC Engraving is a Multifunction Engraving Machine collects engrave
and Milling.The machine mainly applicable to Processing of a variety of mold
like : Embossing plate,Shoe mold, Button mold, zipper-mode, Text die and
stamping die design, equipment molds, glass molds and so on.The machine also
applies to the advertising industry like: Division licenses, signs, architectural
models, badges, badges, nameplates, panels, logo, numbers, signs, craft
decoration, furniture decoration and so on. Besides, applies to portrait,
landscape, calligraphy lettering, seals and other graphic art sculpture, YIN,
YANG Wen-profile, relief production.
Our shop products 4-axis engraving machine drive,using high-performance
dedicated micro-step away from the computer control chip TB6560
TB6560,, Open
microcomputer control according to user requirements to functional design to
the driver board, the composition of the minimum control system. he control
panel is suitable for any small and medium-driven two-phase or four-phase
hybrid stepper motor. And have current 0.6A, 1.2A, 1.8A, 2.5A 4 stalls adjustable
function, support MACH2, MACH3 Series software, support KCAM4 Series
software, extensive application and mold machining, engraving and other
graphic applications. As a result of new bipolar constant-current chopping
technique, high precision, the motor is running, little vibration, low noise,
smooth operation, safe and convenient, the vast number of DIY enthusiasts and
engraving machine manufacturers product of choice.
2
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
2. TB6560AHQ advantage
2.1 At low speed operation System Advantages
Low-speed operating system, is the clock frequency is not high, with small
current drive-based systems, such as the speed of a few per minute to 100 turn,
the user under the conditions in such applications, such as the use of traditional
driving scheme, or a result of integrated chips segmentation is too low, leaving
low-speed vibration is too large; or had to choose a high drive segments, so that
the cost of an unnecessary increase.
TB6560AHQ driver chip's advantages:
(1). Motor vibration, low noise: Because the chip comes with an optional
sub-2,4,16, enough to meet nearly every minute to switch from a few of the
applications.
(2). embedded drive less heat: chip built-in cooling large enough alone to support
small current-driven thermal requirements.
support a variety of stepper motor selection: customers can choose a hybrid
(3).
(3).support
or a slightly larger torque permanent magnet stepper motor, the motor work in
the allowed maximum torque of between 30-50%, the electrical costs of almost
unchanged; chip provides multi-range current set-up and current-decay mode,
supporting the same power index a variety of different parameters under the
stepper motor.
2.2 In high-speed operation System Advantages
High-speed operating system refers to a higher clock frequency, and a large
current drive-based systems, such as the speed of close to 1000 per minute to
switch, under the conditions of such application-driven programs such as the use
of traditional or integrated chip segment is too low due to , leaving the system
speed range is too small; or because of the excessive breakdown of the high
increase in cost, may also occur due to decline in high-frequency torque caused
by vibration and noise.
TB6560AHQ driver chip's advantages:
(1). motor vibration, low noise: As the chip comes with 16 sub-TB6560AHQ chip
functionality, to meet nearly every minute to switch from a few to the application
requirements, and automatically generates a pure sine wave control current, and
other high-integrated chip compared to the same high-speed torque is not only
not fall under the contrary, increase; TB6560AHQ chip can withstand the peak
due to the driving voltage of 40V, 3.5A peak current for the motor torque in the
large, high-speed continuous operation under the offer of the technical support.
3
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
(2). supports a variety of stepper motor selection: customers can choose a hybrid
moment slightly larger or permanent magnet stepper motor, so that the motor
operates at maximum torque of between 30-50%, the electrical costs of almost
unchanged; chip provides high-current set-up and multi-range current-decay
mode, supporting the same power index a variety of different parameters under
the stepper motor.
(3). an embedded easy to drive, small size cooling: large current drive, the chip surface to
facilitate cooling radiator outside the company can also be directly connected to the user's
original controller, metal shell, the embedded drives small size, easy to heat.
In short, due to a high degree of TB6560AHQ chip, the external circuit is
extremely simple, highly reliable, support NEMA23 and some NEMA34 stepper
motor tens to nearly turn the wide speed range applications, will enable CNC
equipment R & D costs and production costs both declined.
3. TB6560T3V1 Driver Board Introduction
The company introduced TB6560T
TB6560T33V1 is the company's accumulated
years of design experience drives that the design made of 3-axis engraving
machine drive. Main features except the 6560 itself, the other features are as
follows:
1.
it can drive four axis,The 5th axis expansion, to facilitate your needs 5-axis
machining when working
2.
With optical isolation and DCDC power supply isolation, the full
protection of your computer parallel port and equipment;
3.
Spindle relay output, easy to use software such as mach3 to control
spindle start and stop
4.
Semi-flow control functions, and effective to stop the motor when the
current is reduced to a minimum
5.
Interface with a fan, you can add fan under your choice
choice..
6.
With
4
way
0.8-3.5A
(peak)
rated
output
of
two-phase
adjustable-current bipolar stepper motor drive
7.
Standard parallel port interface, support for MACH2, KCAM4 series
software;
8.
with limit switch,can connection 4 aixs limit switch
9.
1、1/2
1/2
1/8
1/16
Support four microstepping ——1
1/2、1/8
1/8、1/16
1/16；
4
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
,micro
chips to use as a 5V
10. 12 — 36V single switching power supply
supply,micro
,microchips
power supply, stable and heat small
4. TB6560T
TB6560T44V1 Appearance
5. Interface and its definition
definition::
25-pin parallel port control is defined as follows:
5
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
DB25 control pin (PIN)
EMAIL:[email protected]
The pin of the drive board
Comment
All axes enable
1
EN
2
STEPX
X(First axis) pulse signal
3
DIRX
X(First axis) direction of the
signal
4
STEPY
Y(Second axis)pulse signal
5
DIRY
Y(Second axis)direction of
the signal
6
STEPZ
Z(Third axis) pulse signal
7
DIRZ
Z （ Third axis) direction of
the signal
8
STEPA
A(Fourth axis) pulse signal
9
DIRA
Fourth axis) direction of
A （Fourth
the signal
10
LIMIT-1
Limit input interface 1
11
LIMIT-2
Limit input interface 2
12
LIMIT-3
Limit input interface 3
13
LIMIT-4
Limit input interface 4
14
Relay
15
Blank
16
STEPB-
B(Fifth axis) pulse signal
17
DIRB-
B(Fifth axis
axis))direction of the
signal
18-25
GND
6
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
6. The setting of current,microstepping and
current-decay mode adjustable
、Current-decay mode setting:
6.1
6.1、
Board marked D1D2 (match with DIP swtich 1 and 2) to set the value of switching
current-decay
D1/D2： ON/ON——100%；
ON/OF——25%；
OF/ON——50%；
D1
OF/OF——0%；
D2
7
Working mode
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
ON
ON
Fast decay
OF
ON
50% of fast decay
ON
OF
25%of fast decay
OFF
OFF
Slow decay
Q: The stepper motor driver board the specific role of current-decay What is this?
A: The stepper motor is basically a breakdown of the way current subdivision law, according to the
phase current sine wave to be tangent to the current point as subdivision points. In the phase current to
reach sub-point control is necessary to control the current decay, otherwise it would be if there will be
no way to accurately point overshoot stay in the breakdown of perspective. The motor at different
speeds in different choices of decay mode. Fast decay at high speed, low speed when the slow decay.
Slow decay at high speed there will be vibrations, high noise problem. Low selection of quick decay
can lead to motor weakness and in severe cases closed position. Motor Control IC, the current decay is
the target of H-bridge switch the control mode. Slow decay, when the high side pipes closed, fast decay
time high or low side tubes are closed. Mixed decay is a first, a rapid decay and then a slow decay,
mixing ratio of decay time is also a result of chip and power are not the same as
、microstepping setting
6.2
6.2、
Board marked M1M2(match with DIP swtich 3 and 4) to set the value of
switching microstepping resolution
M1
M2
Working mode
OFF
ON
1/16
ON
ON
1/8
ON
OFF
1/2
OFF
OFF
1
Remark:For motor run smoothly, please try to select high segments, such as 1 / 16 microstepping
8
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
、current setting:
6.3
6.3、
Board marked T1T2(match with DIP swtich 1 and 2) to set the value of switching
current setting
T1
T2
Current
OFF
ON
25%*2.5A
ON
ON
50%*2.5A
ON
OFF
75%*2.5A
OFF
OFF
100%*2.5A
Proposed current as close as possible stepper motor rated current
7.
The connection of kinds of stepper
motors
4 lead wires stepper motor:
9
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
6 lead wires stepper motor:
8 lead wires stepper motor:
10
EMAIL:[email protected]
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
Stepper motor +A -A +B
EMAIL:[email protected]
-B connection AP AM BP BM of board port
8. The limit switch port connection:
11
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
9. The 5th aixs expansion port connection:
10. Drive board and motor match
match::
motor drive in
The driver can drive two or four phase stepper motors,
motors,motor
order to obtain the most satisfactory results, need to select a reasonable set of
supply voltage and current. The supply voltage level of the decision of the
high-speed electrical performance, while the current settings determine the
motor output torque.
12
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
(1) A supply voltage selected:
In general, the more high of the supply voltage, the more torque in high
speed, and able to avoid missing step at high speed. On the other hand, the
voltage is too high may damage the drive
driverr,also big shock in low speed
(2) output current settings:
For the same motor, the greater the current set value, the greater the motor
output torque, but the high heat for motor and driver. Therefore, the general
situation is that the current is set to supply long-term work machine when warm
but not too hot when the values.
when 4 or 6 lead wires stepper motors in high-speed mode: the output
1)
1)when
current is set to equal or slightly less than the motor rated current value;
2) when 6 lead wires stepper motor in high torque mode: the output
current is set to 70% of motor rated current
3) 8 -wire motor connected in series: the output current is set to 70% of
motor rated current
4) 8 -wire motor parallel connection: the output current can be set to 1.4
times more than the motor rated current.
Note: The current setting 15-30 minutes after you run motors, such as the motor
13
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
temperature is too high, it should reduce the current settings.
if after reducing the
settings.if
current value, the motor output torque is not enough, please improve the cooling
conditions to ensure that motors and drives are not hot.
11.
MACH3 software use introduction:
、Mach3 activate
11.1
11.1、
activate::
Fig1 open MACH3
Shown in Fig
Fig11, open the MACH3 software, and then select mach3MILL
then OK!
14
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
Fig 2 mach3 main table
there are some common buttons,then let us set up it!
Open the MACH3 as Fig2
Fig2，there
15
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
、Mach3 software setting:
11.2
11.2、
Fig 3
mach3 setting menu
Shown in Fig
Fig33, open the CONFIG menu under the PORT & PIN menu.
16
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
Fig 4
EMAIL:[email protected]
frequency setting
ting the fundamental frequency, this parameter affect
Circle 1 is for set
setting
the motor rotation speed. Set up and select Circle 2,then will shown in below
Fig5 to set up the Pulse and Direction.
17
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
Fig 5 The pin setting of Dir,Step
Pls click “output signals
signals”” as below Fig6 after set up the Dir and Step to set up the En
and Relay.
18
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
Fig 6 En and spindle relay Pin setting
、Limit switch mach3 setting
：
11.3
11.3、
setting：
setting as Fig7
Click “input signal
signal””，setting
19
EMAIL:[email protected]
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
Fig 7
、G-Code run
：
11.4
11.4、
run：
,mach3 sofware self with G code
G code is the instruction of CNC procedures
procedures,mach3
” File
” as Fig 8.
for customer testing machine easier,click menu
menu”
File”
20
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
图 8 打开 G 文件
Click
sofware
“Load
G-code
G-code””
,
then
open
click G code file
，click
the
file
which
contain
to chose a G code as Fig 9.
21
the
MACH3
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
Fig 9 Open MACH3 with self G code testing procedures
22
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
EMAIL:[email protected]
Fig 10
Open the G code, you can see the red RESET flashing, you can use
mouse click the RESET to stop the flashing, then you can press circle 2 position
CYCLESTART run.
If you want to run yourself G code,the way is same,to find yourself G
code file then open the code is ok.
Also if you need to manual, then you can press TAB key to open the manual
control panel as Fig 11
Fig 11
Note:
1.
2.
3.
pls use desktop PC
pls use Win2000 or XP system
pls not connect or disconnect the motor when board is power on,otherwise
maybe burnt the ICs
4. after install the mach3 pls re-start the PC
5. pls must be wiring connect right,if wrong will burnt the board
6. after mach3 setup,check the motor whether is self-locked
23
CHANGZHOU RATTM MOTOR CO.,LTD CONTACT PERSON:TONY S
24
EMAIL:[email protected]
">