ecombi eco1 eco2 eco3 eco4 installation manual and user guide

ecombi eco1 eco2 eco3 eco4 installation manual and user guide
ECOMBI
ECO1
ECO2
ECO3
ECO4
INSTALLATION MANUAL AND USER GUIDE
Please read these instructions CAREFULLY before installing or using this appliance for the first time.
INSTALLATION MANUAL AND USER GUIDE
1. - WARNING. Please read these instructions before installing or using this appliance for the first time.





















The warranty of the heater will not cover any damage caused by non observance of any of these instructions.
This guide must be kept and given to any new user.
This appliance cannot be used by a non competent person.
The installation must be carried out in accordance with the current local electrical regulations. Any installation or reinstallation
has to be carried out by a fully qualified engineer.
Please check that the voltage in the rating label fits the power supply.
This appliance must be earthed.
The appliance should not be installed just below an electrical socket.
The appliance must be installed in such a way that it is impossible for anyone using a bath or shower, to touch the controls.
The use of these heaters is forbidden in any area where there is a presence of gases, explosives or inflammable objects.
If during any installation the thermal insulation shows any sign of damage, it is necessary for the faulty part to be removed and
replaced by an identical part.
DO NOT USE THIS HEATER TO DRY CLOTHES. Do not cover this heater at any time.
Air inlets and outlets provide proper operation of the appliance and prevent its overheating. DO NOT cover air inlet and
outlet grills.
Surfaces of this appliance could be hot. Children should be supervised to ensure they do not play with the heater.
This heater should be switched off at the isolating switch before any repair work is carried out. This action should also be
taken during the times of the year when heat is not required.
This appliance is only for permanent connection to a fix installation. The installation of the heaters must be carried out in
such a way that each pole can be disconnected from the supply having a contact separation of at least 3 mm.
Nominal charging time of the storage heater is indicated on the characteristics plate.
After installation a survey of the first charging cycle should be carried out to ensure that the main input thermostat switches
off. Ventilate the room during this first cycle.
Never open a charged appliance.
To maintain stability, it is essential that the heater is placed on a level surface and care should be taken to avoid irregular
surfaces, such as may result from carpets or tiled surrounds partially protruding under the heater.
The presence of air particles of smoke, dust and other pollutants could, in time, discolor the walls and surfaces around the
heater.
Incorrect time settings, erroneous programming of the reduced rate time and too high temperature settings may result in a
high cost of your electricity bill.
TECHNICAL FEATURES
Modelo
ECO1
ECO2
ECO3
ECO4
LENGTH
55cm
66cm
89cm
111cm
HEIGHT
73cm
73cm
73cm
73cm
DEPTH
18cm
16cm
16cm
16cm
WEIGHT
59kg
48kg
69kg
90kg
CONVECTOR POWER
450W
600W
900W
1200W
STORAGE HEATER POWER
525W
700W
1050W
1400W
220-240V~
220-240V~
220-240V~
220-240V~
Clase I
Clase I
Clase I
Clase I
-
8
12
16
CONNECTION
INSULATION
NUM. OF BRICKS 4,1 kg
NUM. OF BRICKS 11 kg
ACC. POWER AFTER 14 HOURS
4
-
-
-
7.35 kWh
9.8 kWh
12.6 kWh
19.6 kWh
2
2. - INSTALLATION INSTRUCTIONS
In order to achieve a correct installation of this device, you have to follow the following steps:
1. - Chose the right place to install ECOMBI. It is necessary that the bellow indicated minimum clearance is allowed from the
appliance to any combustible material such as furniture or curtains.
OBJECT
CURTAIN, PIECE OF FURNITURE…
2. - Open the carton at the indicated side and fix the supporting feet without removing the heater.
Turn the carton upside down to allow the heater to stand on its feet and remove the carton. Check that it is the correct model
and that it is in good conditions.
3
3. - Take off the front panel by removing the two screws located at the bottom. Fix the lateral fittings to the metal structure by
using the appropriate screws.
4. - Place ECOMBI in your selected installation area. Use the heater fixing holes as a template and mark the wall through the
fixing holes with a pencil. Drill the required holes into the wall. Place the dowels and screws into the holes before the appliance
installation but do not fasten them tightly.
5. Attach ECOMBI to the dowels with the crews. IT MUST NOT BE HANGED ON THE SCREWS, these are used only to
prevent the device from overturning and not to support it. If there is any doubt concerning the wall strength, consult the
corresponding construction specialist. The appliances are heavy; it is the installer responsibility the correct installation and wall
support of these devices to prevent them from overturning.
6. - Connect the heater using the wiring diagram included in the last page of this manual. Tighten properly the connection block
screws. Use only silicone insulated cables. Do not leave any remaining wire inside the heater.
7. - Disconnect the aluminum heating element by removing the Faston terminal on the right side. Disconnect also the Faston
terminal that connects the element to the safety thermostat.
4
After that please unscrew the inner panel and remove it.
WARNING!
In the interior part of this inner panel there is a very delicate
thermal insulation MICROTHERM panel. It has to be handled with
extreme care. AVOID TOUCHING IT.
8. Do not disconnect the electrical heating elements. Remove the protection cardboards. Lift and recline the elements caring
about not breaking their insulation.
5
9. - Place the storage bricks carefully, with the flat side facing the back of the heater. Arrange two row levels of bricks.
10. Place the heating elements again in their original position. Place the other two rows of storage bricks with the flat side facing
the exterior and always on the heating elements supporting tabs.
11. Refit the inner front panel. If the bricks have been fitted correctly you will find no difficulty in refitting this panel. Please check
the insulation panel is also properly fitted. Please see below:
WRONG
POSSITION
RIGHT
POSSITION
12. - Connect again the two Faston connectors to the aluminum heating element and to the safety thermostat.
13. - Fit again the exterior front panel by connecting first the joints in its upper part. Then push its lower part until the lower
edge lay on the plastic rests.
14. - Fix the front panel with screws.
6
3. - USING THE APPLIANCE.
CONNECTION / DISCONNECTION.
Mains switch. All models are equipped with a switch on the back side panel. It is used to connect / disconnect ECOMBI.
KEYBOARD:
“Clock” key:
“Operation mode” key:
Press the key to display date
and time. Hold it for more than
8 seconds to change values.
Press the key to select different
operation modes.
FROST PROTECTION
AUTOMATIC STORAGE HEATER
EMITTER
ECOMBI MANUAL
ECOMBI AUTOMATIC
KEY “- “
КEY “ + ”:
Press the key to
decrease different
values
Press the key to
increase different
values
KEYBOARD LOCK:
In any operation mode it is possible to lock the keyboard holding the keys
When the keyboard is locked, if any button is pressed, display will show
To unlock the keyboard hold the keys
and
:
simultaneously for several seconds.
and the appliance will not respond.
simultaneously again for several seconds.
SYSTEM TIME SETTING
It is necessary to set the system time for the appliance to follow correct programming and to adjust it correctly to the off peak
time periods. Off peak periods have to fit with the ones established in GENERAL SETTINGS part as P1, P2, P3, and P4 (please
go to “General Settings” part).
In order to set the system time, hold the key
keys.
for 8 seconds. The Hour values are changed with the
Then press the
key to save and proceed to change the minutes values. Press
the week day if weekly programming option is enabled in the GENERAL SETIINGS part:
and
again to save and proceed to change
In the case it is necessary to set up different values for different days in a week, please go to “ General Settings” part in this
manual and change P7 setting to “ON” position. Once it is changed come back to “System time setting”, set hour, minutes, week
day and validate.
NOTE:
ECOMBI does not change automatically from summer time to winter time or vice versa. It is necessary to
change the clock settings to fit these two timings.
7
OPERATION MODES:
Pressing the
key various operation modes may be selected: FROST PROTECTION, AUTOMATIC STORAGE
HEATER , EMITTER, ECOMBI MANUAL or ECOMBI AUTOMATIC.
1 - FROST PROTECTION MODE:
To select this mode press the
key several times until the message
is displayed. The set up temperature
will be 7º C. the appliance will maintain this temperature through convector operation. Storage heater will be off in any case.
2 – AUTOMATIC STORAGE HEATER MODE:
To select this mode press the
key several times until the message
. is displayed.
“АС” stands for STORAGE HEATER in Spanish language. “4.0” would be the charge control position set to position 4.
As in a standard storage heater equipped with a 5- position charge control, charging settings in ECOMBI go from 0
(minimum charge) to 5 (maximum charge):
5.0 = charge 100% (during all the reduced rate time)
4.5 = 90%
4.0 = 80%
3,5 = 70%
3.0 = 60%
2.5 = 50%
2.0 = 40%
1.5 = 30%
1.0 = 20%
0.5 = 10%
0.0 = 0%
While ECOMBI is charging (electric consumption) a small red dot will appear between the A and the C in the display.
DEFERRED CHARGING:
This function in ECOMBI allows optimizing the energy management and consumption. In a off-peak period of 8 hours, if there is
the case where it is only necessary to charge at 50%, this is 4 hours. This function will make that the effective charging period
would be the last 4 hours during the off-peak period. This will make that ECOMBI is at full charge at the beginning of the
“cession” period.
In order to enable / disable this option please go to “General Settings” part in this manual and change P6 setting as ON / OFF.
PROTECTION FOR EXCESS OF TEMPERATURE IN THE ROOM:
In order to reach maximum saving and avoid unnecessary energy consumption, if there is the case that during the charging
period the temperature in the room excess the temperature set up in ECOMBI for that room, then the charging will be
interrupted until the temperature in the room decreases 1ºC.
8
3 – EMITTER MODE:
This operation mode is used when it is necessary to heat the room temporarily and there is no need for storage heating.
Press the
key several times until the message
is displayed.
“Е” stands for EMITTER.
“21.5” stands for the set up temperature in ºC.
Emitter will operate until the temperature in the room reach 21,5ºC, then, it will maintain the temperature.
If needed, it is possible to change the set up temperature by using the keys
changing in steps of 0,5ºC.
and
. Temperature value will be
Small red dot at the very right part of the display will show that the convector heating element is working at that moment.
Pressing simultaneously keys
and
will display room temperature taken from the sensor at the bottom of the
device.
It can be the case of a temperature difference between this sensor and a normal thermometer set up in a wall room. This is
because temperature is different at different heights in the room. The one at the floor is normally lower. User can adjust the
sensor so that different thermometers show same temperature. For this you can go to General Settings part and modify the
sensor reading according to P5 setting.
4 – ECOMBI MANUAL MODE:
This mode will allow ECOMBI to operate the Storage Heater and the Convector together in a combined way. The Storage
Heater will charge based on the settings of “AUTOMATIC STORAGE HEATER MODE” and if there is any kind of heat loss in
the room and a decrease in the temperature, ECOMBI may operate the “EMITTER MODE” to compensate and balance again the
room temperature.
To select this mode press the key
several times until in the display only appears the set up temperature. This is without
any preceding letter “A” or “E” displayed. I.e.
. This means that 21,5ºC is the system set up temperature (default).
It is possible to adjust the set up temperature by using the keys
steps of 0,5ºC.
and
. Temperature value will be changing in
When the convector heating element is working a small red dot will appear at the very right part of the display.
In this mode, the set up temperature is independent from the set up charging %. Default setting for charging % is 4 (80%). Please
read under “STORAGE HEATER mode” if you want to modify it.
While ECOMBI is charging (electric consumption) a small red dot will appear on the left side of the display
.
Storage Heater and Convector never work at the same time. This is, both powers never are added. Emitter may operate at any
time of the day or the night, including off-peak periods, but only if Storage Heater is not charging.
5 -ECOMBI AUTOMATIC MODE, with charge correction.
In this mode ECOMBI operates in a combined way. Storage heater operates during off peak rate, and when it is not being
charged, ECOMBI may operate as Emitter providing additional heating to the room if necessary.
BESIDES THIS THERE WILL BE AN AUTOMATIC CHARGE CORRECTION OF THE STORAGE HEATER FOR THE
FOLLOWING DAYS.
To activate this mode press the
key for several times until the message
А stands for AUTOMATIC mode.
21,5 is the set up temperature in ºC.
When the Emitter is on, a small red dot at the very right of the screen will be displayed.
9
is displayed.
A small red dot next to A will be displayed, when storage heater is on.
Operation in this mode is similar to the Ecombi Manual Mode but the % of the storage heater charge is corrected automatically.
If working hours of Emitter is higher than certain value, storage heater charge will increase in a certain %. On the other hand, if
Emitter working hours does not exceed this value, storage heater charge level is reduced in the same %.
This behavior adapts the consumption to the real thermal needs, allowing the maximum level of energy savings at the required
comfort required.
The set up temperature is independent of the Storage Heater level of charge. Default setting for charge is 4.0, this value can be
modified by entering in STORAGE HEATER MODE and changing these charging values from 0 to 5.0.
WEEKLY PROGRAMMING
It is possible to select which days ECOMBI will work and which days will not be working.
By activating P7 in GENERAL SETTINGS, this option will be enabled.
To enter in weekly settings, please hold the key
Blinking hours will be displayed. Press the
first day of the week will blink.
for 8 seconds.
key, then blinking minutes will be displayed. Press the
Change the week day if necessary with the keys
and
. Press the
key, then the
key to save.
After that it is possible to select which days of the week will ECOMBI follow the selected mode operation or FROST
PROTECTION operation. An example can be seen here below.
In this example ECOMBI will
be operating in normal mode
from Monday (day 1) to
Friday, and in FROST
PROTECTION mode on
Saturday and Sunday.
One or two segments will be blinking for Day 1.
One segment stands for FROST PROTECTION permanent mode.
Two segments stands for SELECTED MODE (last mode selected out of the five available).
Proceed to change the value for the day 1 with keys
the day 7.
and
10
, save with
key. Proceed to day 2 and so on to
GENERAL SETTINGS:
ECOMBI general operation settings can be modified.
By pressing the
key at the same time we connect the device with the mains switch located at the right side panel, we
enter to the general settings menu. This is:
P1
P2
P3
P4
P5
P6
Starting time of reduced (off peak) rate electric period.
Ending time of reduced rate electric period.
Starting time of the second reduced rate electric period (if not available set up 00.00).
Ending time of the second reduced rate period (if not available set up 00.00)
Temperature sensor correction (values from -5ºC to +5ºC)
Deferred charge ON: charge ends at the same time than reduce rate period.
OFF: charge stars at the same time than reduce rate period...
Weekly programming ON/OFF.
Limit factor of emitter operation mode to increase or reduce the charge
(Possible values 0.05 - 0.10 - 0.15 - 0.20 - 0.25 - 0.30 - 0.35 - 0.40)
Percentage of automatic charge regulation (values: 05-10-20-25)
Excess of temperature protection during the charge. Degrees higher than the set up
temperature when the charge is interrupted. (Values 1 - 2 - 3 - 4 - 5)
P7
P8
P9
PA
Advance with the keys
and
, push the
key to enter in a parameter. Use same keys to modify it.
To save the new values it is necessary to pass through all of them to the last one (PA).
DEFAULT SETTINGS:
By pushing the Clock key of the device connected to the mains. Software resets to the default settings. Four horizontal blinking
segments will appear in the screen to confirm it.
4.- MAINTENANCE
ECOMBI does not need any special maintenance.
Clean and dust with a dry, soft cloth only when the unit is disconnected and cold.
Do not use any solvent or abrasive product for cleaning.
When the Heating season is finished, please disconnect the device by the mains switch located at the right back lateral of the
unit.
ECOMBI has been manufactured under a fully assured quality system and using environment friendly processes.
Once its useful life is finished please take the device to a clean point so that its components can be recycled in an adequate way.
5.- TROUBLESHOOTING
ECOMBI does not heat.
Please check it is connected and switched on.
Make sure the device is not covered or the lower air inlets are not obstructed. May be the LR limit
thermostat is activated; in this case it is necessary to rearm it manually.
ECOMBI does not reach set up
temperature
Make sure that adequate temperature is selected.
Make sure room heat looses fit the power of the device.
ERR 1 in display
Temperature sensor trouble, please do contact to the technical assistance.
Key board does not respond
If display shows [ - - ] display is blocked. Press at the same time “+” and “-” key during some seconds
to unblock it..
11
6.- CONNECTION DIAGRAMS
EN:
I
R1, R2, R3, R4
RE
LA
LE
LR
K
MB
Mains switch.
Storage heater heating elements.
Emitter Heating elements.
Storate heater limit thermostat.
Emitter limit thermostat
Limit thermostat with manual rearm.
Keyboard
Electronic circuit board.
WARNING: To avoid overheating do not cover the heater.
EN
The symbol on the product or in its packaging indicates that this product may not be treated as household waste. Instead
it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your local city office, your household waste disposal service or
the shop where you purchased the product. These instructions are only valid in the EU member states.
www.elnur.es
[email protected]
Manufactured by ELNUR s.a.
Pol. Ind. “El Nogal” c/ Villa Esther, 11
28110, ALGETE – Madrid
Made in Spain
Technical modifications possible without prior notice @2012
12
Cod. 15190013 rev.1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement