kinetec spectra knee cpm user manual

kinetec spectra knee cpm user manual
Manuel d'utilisation
User manual
Avant toute utilisation lire ce document.
AbilityOne Kinetec se réserve le droit de toutes modifications techniques.
Before use, please read this document.
AbilityOne Kinetec reserves the right to effect technical modifications.
Istruzioni per l’uso
Vor Benutzung unbedingt dieses Dokument lesen.
AbilityOne Kinetec behält sich das Recht vor, jegliche technische Änderung durchzuführen.
Prima di mettere in funzione l’apparecchio leggere con attenzione il presente documento.
La AbilityOne Kinetec si riserva il diritto di apportare modifiche tecniche.
Manual de empleo
Antes de cualquier utilización, lea este documento.
AbilityOne Kinetec se reserva el derecho a cualquier modificación técnica.
Bedienungsanleitung
Your contact:
F
GB
D
I
E
SUMMARY
Page
• Definition__________________________ 2
• Description ________________________ 3
• Safety____________________________ 4
• Electrical connection __________________ 5
• Use of the hand control
- Select your language _______________________6
- Locking the hand control setting ________________7
- START/STOP/REVERSE function _________________7
- Quick Start _____________________________8
- Possible values for each parameter ______________8
- How to adjust the basic parameters of the movement ___9
- How to modify programs PROGRAM MODE __________10-12
- Using Programs __________________________13
- Reading the values of a program ________________14
Page
- How to use the WARM UP key _________________
- How to use the MODULATION key _______________
- How to use the BYPASS key __________________
- Session Time____________________________
15
16
17
18
- Maintenance ____________________________
- Troubleshooting__________________________
- Cleaning_______________________________
- Technical specifications _____________________
- Symbols used ___________________________
- Warranty ______________________________
- Maintenance sheet ________________________
22
22
23
23
24
24
25
• Patient Pad kit _______________________ 19
• Setting up the patient___________________ 20
• Options ___________________________ 21
• Product information
SAFETY RECOMMENDATIONS
• The physician defines the protocol and ensures that it is correctly implemented (adjustments, session time and frequency of use).
• We recommend that you lock the hand control when you give it to the patient.
• For optimum safety, always give the hand control to the patient before starting the system.
• Explosion hazard: KINETEC Spectra is not designed for use in the presence of flammable anaesthetics.
• Check that the electrical socket is in good condition and is suitable for the splint power supply cord. The latter complies with current standards and
has a grounding socket. The plug may be connected to any standard socket. The socket must however have a grounded pin.
To connect the power supply, only use the original cable supplied with the machine.
Check that the cables remain free around the device so that they do not get damaged.
Manuel N°467896275 - Updated 21/02/03
GB
1
Definition
The KINETEC Spectra is a Knee PASSIVE mobilization device enabling the extension and flexion movement from -10° to 120°.
• Indications
• Knee replacement surgery.
• Fractures (patellar, tibia plateau, femoral,...).
• Arthrolysis
• Hip surgery, including hip replacement, hip pinning, osteotomy,...).
• Ligament repairs.
• Arthroscopic surgery (menisectomies, patellectomies,...)
• Burns, joints sepsis,...
• Clinical Benefits
• Breaks the cycle of trauma, inflammation and the loss of range of motion.
• Prevents joint stiffness.
• Speeds the recovery of post-operative range of motion.
• Maintains the quality of the joint surface.
• Reduces pain and edema.
• Promotes joint cartilage healing.
• Reduces hospitalization time
• Reduces the need for pain medication.
• Provides immediate post-operative continuous passive motion.
• Digital ROM readout on the patient hand control for positive reinforcement.
• Maintains desired positions for stretching and muscular rest.
• Contraindications
Bone Cancer, Warped joint surfaces, Spastic paralyses, Unstable fractures, Uncontrolled infection.
The machine are not adapted for patients height more 2 m(6'7") or under 1,40m (4'7").
GB
2
Description
KINETEC Spectra consists of the following components:
1 • Lower limb support.
2 • Thigh support.
3 • Foot support and hand control location for transport.
4 • Hand control.
5 • Thigh support setting lock.
6 • Lower limb support setting lock .
7 • Foot support positioning setting lock.
8 • Transport handle.
9 • ON/OFF switch and fuses.
10 • Liquid-crystal display (2 lines of 16 characters).
11 • SESSION TIME display key.
12 • BYPASS mode key.
13 • MODULATION key.
14 • WARM UP key.
15 • EXTENSION setting key.
16 • FLEXION setting key.
17 • Increase / decrease keys.
18 • START key.
19 • STOP key.
20 • FORCE key.
21 • SPEED key.
22 • PAUSE key.
23 • TIMER key.
24 • PROGRAM access key.
1
6
3
2
7
5
9
4
8
14 13
12
11
10
16
15
17
18
21
22
19
20
24
23
GB
3
Safety
The physician defines the protocol and ensures that it is correctly implemented
(adjustments, session duration and frequency of use).
The patient must know the start/stop/reverse function on the control handle. Hand control must be accessible to patient at
all times. (See page 7).
KINETEC Spectra complies with Directive 93/42/CEE.
EXPLOSION HAZARD:
KINETEC Spectra is not designed for use in the presence of flammable anesthetics.
In case of electromagnetic interference with other devices move the device.
KINETEC Spectra is in compliance with standards in force (IEC 601.1.2), electromagnetic compatibility standard for medical
devices.
GB
4
Electrical connection
KINETEC Spectra is a type B class I device.
Before connecting the device to the power supply, check that the mains voltage
matches that shown on the identification plate (100-240 V~ 50-60Hz).
Connect the hand control (4)
Connect the power supply cable (25).
IMPORTANT
Check that the electrical socket is in good condition and is suitable for the splint power
supply cord. The latter complies with current standards and has a grounding socket.
The plug may be connected to any standard socket.
The socket must however have a grounded pin.
To connect the power supply, only use the original cable supplied with the machine.
Check that the cables remain free around the device so that they do not get damaged.
9
25
4
Starting the unit
Switch on (9).
While the unit begins an auto diagnostic, the display shows the following :
KINETEC
Spectra V01.0
Please wait
30
Kinetec
STOP
15
90
Your KINETEC Spectra is ready to be used.
GB
5
Use of the hand control
Select your language
Beginning
Keys to press
Display
Remarks
KINETEC
Spectra V01.0
Switch the unit ON
Please wait
Kinetec
30 STOP
15 90
Language:
english
Press the 2 keys in the same time
Check if the hand control is not blocked
(See page 7).
The display indicate the language selected.
The English language is selected.
To change the language
To validate the new language.
GB
6
or
Language:
English
Ok
Switch on/off
English
French
German
Italian
Spanish
To exit and confirm the new language, switch
OFF and Switch ON the unit.
Use of the hand control
Locking the hand control setting
The hand control allows the patient to control the machine as appropriate.
Simultaneously press the
and
keys to lock the hand control,
The display reads "LOCK", you can not change the parameters, if you try the display reads "LOCK".
To unlock the hand control, simultaneously press the
and
keys, The display reads "UNLOCK".
We recommend that you lock the hand control when you give it to the patient.
Comment: The hand control is unlocked when you switch the unit ON/OFF.
START/STOP/REVERSE function
As with all KINETEC systems, KINETEC Spectra is equipped with a START/STOP/REVERSE function.
When the unit is running, the display reads RUN
Press the
key of the hand control. The movement stops. The display reads STOP.
Press the
key of the hand control. The movement starts in the opposite direction and the display reads RUN.
Caution:
For optimum safety, always give the hand control to the patient before starting the system.
GB
7
Use of the hand control
Quick Start
Set up the patient and proceed as below:
Beginning
Keys to press
Display
Remarks
KINETEC
Spectra V01.0
Please wait
Kinetec
30 STOP
15 90
Switch the unit ON
Or
30
Start the session with the original parameters of the
movement (default setting).
30
WARMUP
STOP
15
KINETEC
run
45
• Treatement Mode
• Extension limit
• Flexion limit
• Speed
• Force
• Extension pause
• Flexion pause
• Timer
GB
8
-10 to 115°
-5° to 120°
1 to 5 (from 30° to 160° per minute)
1 to 6
0 to 900 seconds (15minutes)
0 to 900 seconds (15minutes)
No timer(00H00) to 24H00
If the Warm Up mode is selected, switch OFF
this mode by pressing on the key
90
90
Possible values for each parameter:
Possible values
Check if the hand control is not blocked
(See page 7).
Default setting
Normal
30°
90°
2
6
0
0
0
The value change at the speed of the
movement.
Use of the hand control
How to adjust the basic parameters of the movement
Beginning
Keys to press
To stop the unit
30
To display the extension or flexion limit of the movement
To change the limit if necessary
or
Or
Or
Or to display pause in extension or flexion limit
To validate the new value press another key
or wait more than 3 seconds. The display shows the
selected mode.
KINETEC
STOP
15
Remarks
90
KINETEC
Ext
15
90
KINETEC
40 Flex
15
90
30
KINETEC
40 Flex
15
110
KINETEC
SPEED 2
FORCE _ _ _ _ _ _
No timer
To validate the new value, press another key
or wait more than 3 seconds.
To change the pause if necessary
Display
Or
KINETEC
PAUSE HIGH
Pause low
0
0
KINETEC
PAUSE low
15
40
KINETEC
STOP
15
110
Check if the hand control is not blocked
(See page 7).
The value blinks.
The new value blinks.
While the value blinks press
the
or
key
to change if necessary.
Successive presses on this key selects the
pause at the extension or flexion limit.
The new pause value blinks.
The unit is ready to start with the new
parameters.
GB
9
Use of the hand control
How to modify programs PROGRAM MODE
Beginning
Keys to press
Display
Remarks
Check if the hand control is not blocked
(See page 7).
To switch off the unit
KINETEC
Spectra V01.0
Press the two keys at the same time and switch the unit
ON
Program
EMPTY
Then
The program number blinks.
10
110
The new program number blinks.
Program
25
warmup
10
110
The display indicates the selected treatment
mode, the program number blinks again.
Or
Program
25
kinetec
10
110
To display the extension or flexion limit of the movement
Program
30 warmup
10
100
Program
30 warmup
10
110
To change the program if necessary
Program
25
kinetec
2
Welcome text during 3 seconds.
or
To choose the treatment mode
GB
10
or
The value blinks.
Use of the hand control
How to modify programs PROGRAM MODE (continued)
Beginning
To change the limit of movement if necessary
To validate the new value, press another key
or wait more than 3 seconds
Keys to press
or
Display
Program
30 warmup
Program
SPEEd: 2
Remarks
10
120
10
While the value blinks press
FORCE _ _ _ _ _ _
No timer
Pause low
0
To record the program 10
Program
10
Save:+
clear:-
Then
Program
Save
Program
EMPTY
OR
To cancel the program
To exit program mode, switch OFF and switch ON the unit.
The new value blinks.
10
11
Program
10
clearing
Program
11
EMPTY
KINETEC
Spectra V01.0
the
or
key
to change if necessary.
The program 10 has been recorded and the
display indicates the next program so you can
change another program.
The program 10 has been cancelled and the
display indicates the next program so you can
change another program.
To use the modified program see page 10.
GB
11
Use of the hand control
Comments:
Comments
• When a program has been deleted, the display shows
Program
EMPTY
11
Program table:
• Program
number
Treatment Mode
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
GB
12
Flexion limit
Extension limit
Speed
Force
Flexion Pause
Extension Pause
Timer
Use of the hand control
Using Programs
The KINETEC Spectra allows you to store up to 16 programs, including the type of treatment, ROM, speed, load, pauses and timer.
The original parameter values of the program are empty.
These values can be modified and recorded at any time (see ‘How to enter a program’ page 10).
Beginning
Keys to press
To stop the unit
KINETEC
STOP
15
40
To access the program mode
To change the program if necessary
Display
Start the unit
Check if the hand control is not blocked
(See page 7).
1
110
The program number blinks.
PROGRAM
25 warmup
3
90
The new program number blinks.
KINETEC
Please wait
To exit and validate the selected program
To exit without validation of selected program
110
PROGRAM
WARMUP
70
or
Remarks
40
25
KINETEC
STOP
15
warmup
run
20
The current parameters have been recorded in
program 3.
110
90
Back to the starting parameters.
The value change at the speed of the
movement.
Comments:
• The values shown in the ‘Display’ column are examples. They actually depend on the stored programs.
• The current movement parameters can be changed while using that program but no data will be stored in the original program.
See the programming mode (p 10) to modify programs.
GB
13
Use of the hand control
Reading the values of a program: example SPEED
Beginning
Keys to press
To stop the unit
110
Check if the hand control is not blocked
(See page 7).
Program
WARMUP
1
110
The program number blinks.
PROGRAM
25 warmup
3
90
To change the program if necessary.
70
or
PROGRAM
Speed
To read the speed value
After 15 seconds or after pressing on another key
To exit and validate the selected program
Start the unit
Remarks
KINETEC
STOP
15
40
To access the program mode
To change the program if necessary
Display
70
PROGRAM
WARMUP
40
40
KINETEC
STOP
15
KINETEC
run
15
5
3
Displays the speed value.
3
110
110
110
The current parameters have been recorded in
program 3.
The value change at the speed of the
movement.
Comments:
• The values shown in the ‘Display’ column are examples. They actually depend on the stored programs.
• The current movement parameters can be changed while using that program but no data will be stored in the original program.
See the programming mode (p 10) to modify programs.
GB
14
Use of the hand control
How to use the WARM UP key
Keys to press
KINETEC
STOP
15
40
WARM UP
STOP
15
15
WARM UP
RUN
15
110
90
The value change at the speed of the
movement.
Pre-Set ROM
Cycle 7 (100%)
Cycle 6 (95%)
Cycle 5 (90%)
50°
Cycle 4 (85%)
100°
Cycle 3 (80%)
The Kinetec Spectra starts at 70% of the full ROM, increasing 5% of the range
every other cycle until the pre-set ROM is reached.
Comments:
Comments
The calculation mode used enables reaching the pre-set ROM in approximately
seven full cycles.
Check if the hand control is not blocked
(See page 7).
The display shows the default settings
(see page 8).
To change the movement value if necessary
see page 9.
30
Warm Up rules:
Example:
Example
For a Warm Up treatment with a pre-set ROM from 0° to 100°.
The first cycle starts from 15° to 85° to 15° and increase 5% each cycle.
110
PLEASE WAIT
To select the Warm Up mode
Start the movement
Remarks
Cycle 2 (75%)
To stop the unit
Display
Cycle 1 (70%)
Beginning
0°
GB
15
Use of the hand control
How to define the patient tolerance • At the start of a session
This function, MODULATION Mode is a way to set within the tolerance of a patient at the beginning of a session.
Set up the patient and proceed as below:
Beginning
Keys to press
Display
Remarks
KINETEC
Spectra V01.0
Switch the unit ON
Or
Please wait
Kinetec
30 STOP
15 90
30
for extension)
To set the pain level when reached, immediately press
To start the session with the new movement limits
GB
16
If the Warm Up mode is selected, switch OFF
this mode by pressing on the key
90
MODUL.: use + or 30 STOP
15 90
The display indicates the keys to be used to
drive the machine, this message is displayed 3
seconds.
or
MODUL.: use + or 30manual 50 90
The unit is moving to the selected way.
It is waiting for you to select new limits.
or
MODUL.: use + or 30manual 50 50
The new limit of the movement is recorded
To select the MODULATION Mode
To select the pain level
(
for flexion,
WARMUP
STOP
15
Check if the hand control is not blocked
(See page 7).
30
KINETEC
run
45
50
The angle display changes with current
movement.
Use of the hand control
How to define the patient tolerance • During the session
This function, The BY-PASS MODE is a way to address the pain threshold of a patient during a session.
IMPORTANT: Can be used only when the machine RUN.
Beginning
Keys to press
Display
30
The unit is running
Kinetec
RUN
15
Remarks
90
Or
30
WARMUP
RUN
15
90
PYPASS: use + or 30 RUN
15 90
To select the BYPASS mode
Check if the hand control is not blocked
(See page 7).
The display indicates the keys used to run the
machine.
This message is displayed 3 seconds.
To select the NEW pain level
or
BYPASS: use + or 30bypass 100 90
The unit is moving to the selected way.
It is waiting for you to select new limits.
To set the NEW pain level when reached, immediately
press
or
bypass.: use + or 30manual 50 50
The new limit of the movement is recorded.
Continue the session with the new movement limits.
30
WARMUP
run
45
50
The angle display changes with current
movement.
GB
17
Use of the hand control
Session Time
This function shows the running time (in minutes) of the session (motor functioning).
• It directly accessible by the key
, the display shows
This counter is reset each time the unit is switched ON.
GB
18
TIME
30 STOP
02h25
15 90
Use of the Kinetec Patient Pad Kit
The KINETEC Patient Pad Kit is designed for rapid fitting, optimal hygiene and maximum patient comfort.
- For using and positioning the straps, please refer to here under. Make sure that the self-adhesive parts (26) are visible.
- Place the sponge side next to the skin.
FOR OPTIMAL HYGIENE, A NEW SET OF PADS SHOULD BE USED FOR EACH PATIENT.
Each cover is provided with a label to record the patient’s name
CLEANING:
- Sterilization of the pads ( if necessary): Sterilized at 134 °C during 18 minutes.
- Disinfecting of the pads: Washing at 30°C with use of a disinfecting solution during the rising cycle.
Example of product that can be used: Solution " Baclinge" at 0.125 % or "Souplanios" at 0,125% from ANIOS Laboratory.
A complete list of distributors in your country is available on request.
The KINETEC Spectra is delivered with a complete set. Components:
- 4 straps
- 1 foot support
- 1 cover
26
GB
19
Setting up the patient
Place the KINETEC Spectra machine in a position that will be comfortable for the patient.
- Measure in cm or inches the length of the patient’s femur (L); adjust the thigh support to this measurement using knobs (5)
- To install the patient on the KINETEC Spectra machine.
- Push the foot plate (3) up to the patient and tighten the knobs (6).
- Adjust the plantar flexion (40°) or the dorsal flexion (30°) of the foot, with the knobs (7).
- Adjust the internal (30°) or external (30°) flexion of the foot, with the knob (27).
IMPORTANT
Adjust the axis of the patient’s hip (28) with the axis rotation (29) of the KINETEC Spectra machine,
and the axis of the patient’s knee (30) with the axis rotation (31) of the KINETEC Spectra machine.
3
6
30
31
L
7
29
28
27
5
GB
20
Options
Cart
GB
21
Product information
Maintenance
After 2,000 hours of operation, KINETEC Spectra requires a few lubrication and maintenance operations (lubrication of the joints, pointer stops and ball screws).
The need for maintenance is indicated by display of the message SERV. MOTOR when the system is switched on.
Despite that warning, you can continue to use your KINETEC Spectra by pressing START, but you should contact your nearest KINETEC technician to have the maintenance
operations conducted as soon as possible.
• A motor running time counter is available. Simultaneously press keys
RESET TIME 924H
Reset: limit low
Troubleshooting
and
this counter can be resetting by pressing the key
, the displays shows
.
A spare parts list and technical catalog are available to you on request from your KINETEC distributor.
If, after connecting the power supply cable to the power supply and switching on KINETEC Spectra:
• The display does not indicate any information:
- Check that the electrical socket is live using another device.
32
- Replace the fuse(s) (32) of the connector with fuses of the same type and calibre:
2 fuses T 750 mA 250V (6.3 x 32) (KINETEC order: 4610007434).
- If the display still does not indicate any information, contact your nearest KINETEC technician.
• Your KINETEC Spectra does not work and the display indicates 50 STOP 25 115,
Press START again.
Your KINETEC Spectra still does not function: Contact your nearest KINETEC technician.
• Your KINETEC Spectra does not function and the display indicates:
ANGULAR POSI.: angle measurement function failure,
or NO MOVEMENT: no movement,
or BAD WAY: motor rotation failure,
or LOAD MAXI: abnormal consumption,
or POWER SUPPLY: power failure;
Contact your nearest KINETEC technician if the same message is displayed after having switched the device off, then on, and started it by pressing START.
GB
22
Product information
Cleaning
Before conducting any cleaning operation, SWITCH the unit OFF and disconnect the power supply.
Use a DISINFECTANT (PROPANOL/ISOPROPANOL or ALDEHYDE-based solution). Spray the disinfectant on the SURFACES (plastic shells and metal components).
In order to ensure optimal hygiene, you are advised to clean the covers for each new patient. All the consumables enable hazard-free disposal.
Technical specifications
Product:
Weight:
Splint dimensions:
Angular limits:
Speed:
Patient height:
11Kg (24 pounds)
94cm (37 inches) x 33cm (13 inches) x 33cm (13 inches)
-10° to 120°
from 30 to 160° per minute for average femur length
full leg: 71 to 104 cm (28 to 41 inches)
Tibia: 38 to 58 cm (15 to 23 inches)
Femur: 33 to 46 cm (13 to 18 inches)
Electricity:
Power supply: 100-240 V~
Frequency: 50-60 Hz
Power consumption: 50 VA
Device of type B class I
IP 20.
Fuse T 750mA 250V 6.3x32mm (KINETEC order: 4610007434)
Environment
- Storage/transport conditions: Temperature: -40 to 70°C / -40 to 160°F
Relative humidity: up to 90%
- Operating conditions:
Room temperature: 10 to 40°C / 50 to 105°F
Relative humidity: up to 80%
GB
23
Product information
Symbols used
TYPE B device
(protection against electric shocks)
Speed
Flexion limit
Caution
(consult the accompanying
documents)
Timer
Warm Up
STOP (power off)
Force
Modulation
ON (power on)
Pause
Bypass
Start movement
Increase
Session time
Stop movement
Decrease
Program access
Extension limit
Warranty
~
Alternative current
The KINETEC warranty is strictly limited to the replacement free of charge or repair in the plant of the component or components found to be defective.
KINETEC guarantees its joint passive mobilization systems for 1 year against all defects of manufacture from the date of purchase by the consumer.
KINETEC is the only organization able to assess the application of the warranty to its systems.
The warranty will be considered null and void if the device has been used abnormally or under conditions of use other than those indicated in the user's manual.
The warranty will also be considered null and void in the event of deterioration or an accident due to negligence, inappropriate surveillance or inappropriate
maintenance, or due to transformation of the equipment or an attempt to repair the equipment.
GB
24
Product information
Maintenance sheet
Serial number: _______________
Purchasing date: ____________________
Date: _________________________________________
Operations done: ___________________________________
Technician: _____________________________________
______________________________________________
Running time (see page 22): __________________________
______________________________________________
Exchange parts: __________________________________
______________________________________________
_____________________________________________
______________________________________________
Date: _________________________________________
Operations done: ___________________________________
Technician: _____________________________________
______________________________________________
Running hours (see page 22): _________________________
______________________________________________
Exchange parts: __________________________________
______________________________________________
_____________________________________________
______________________________________________
GB
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement