Yamaha | MCR-B020 | Owner's Manual | Yamaha MCR-B020 Owner's manual

Micro Component System
OWNER’S MANUAL
AB
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this unit in a well ventilated, cool, dry, clean place away from direct sunlight, heat sources, vibration, dust,
moisture and cold. For proper ventilation, allow the
following minimum clearances.
Top: 15 cm (6 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in an
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit, which
may cause an electrical shock, fire, damage to this unit,
and/or personal injury.
5 Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage other
than specified.
13 To prevent damage by lightning, keep the power cable
disconnected from a wall outlet or this unit during a
lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed.
The cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the
wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
17 Before moving this unit, press
to set the unit to off,
and disconnect the AC power plug from the wall outlet.
i En
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may become
warm. Turn off, then leave this unit alone for cooling.
20 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like. When you dispose of
batteries, follow your regional regulations.
– Keep the batteries in a location out of reach of children.
Batteries can be dangerous if a child were to put in his or
her mouth.
– If the batteries grow old, the effective operation range of
the remote control decreases considerably. If this happens,
replace the batteries with new one as soon as possible.
– Exhausted batteries may leak. If the batteries have leaked,
dispose of them immediately. Avoid touching the leaked
material or letting it come into contact with clothing, etc.
Clean the battery compartment thoroughly before
installing new batteries.
– If you plan not to use the unit for a long period of time,
remove the batteries from the unit. Otherwise, the batteries
will wear out, possibly resulting in a leakage of battery
liquid that may damage the unit.
– Do not throw away batteries with general house waste.
Dispose of them correctly in accordance with your local
regulations.
22 Excessive sound pressure from earphones and headphones
can cause hearing loss.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off by
. In this state, this unit is designed
to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
There is a chance that placing this unit too close to a CRTbased (Braun tube) TV set might impair picture color.
Should this happen, move this unit away from the TV set.
CONTENTS
NAMES OF PARTS AND THEIR FUNCTIONS ........2
LISTENING TO FM STATIONS ..............................11
Top panel/Front panel ....................................................2
Front panel display.........................................................2
Remote control...............................................................3
Selecting an FM station................................................11
Presetting FM stations (remote control only) ...............12
Selecting preset FM stations ........................................13
CONNECTIONS ........................................................4
LISTENING TO EXTERNAL SOURCES ................13
USEFUL FUNCTIONS ............................................14
Connecting the speakers and antenna ..........................4
Connecting the power cable...........................................5
Other connections ..........................................................5
About the standby state .................................................5
How to use the remote control .......................................5
ADJUSTING THE CLOCK (OPTION MENU) ...........6
LISTENING TO CD AND USB DEVICES .................7
Listening to a CD............................................................7
Listening to a USB device ..............................................8
Using repeat/shuffle playback (remote control only) ......8
Using the Option menu ................................................14
Using the sleep timer ...................................................15
Using the alarm function ..............................................15
Setting the alarm ..........................................................16
Operations while the alarm sound is playing................17
TROUBLESHOOTING ............................................18
NOTES ON DISCS AND USB DEVICES ................21
SPECIFICATIONS...................................................22
LISTENING TO MUSIC FROM YOUR Bluetooth
DEVICE......................................................................9
Playing back from your Bluetooth device .......................9
Connecting an already-paired device via Bluetooth.....10
Disconnecting a Bluetooth connection .........................10
Features
• Play back music from external devices such as your audio/data CDs, USB devices, or external devices via the AUX jack,
and listen to the radio.
• By the Bluetooth technology, you can enjoy clear sound without wire connections.
• Use your favorite music as an alarm. When the set time arrives, the music you select is played at the volume that you
specify, giving you the ideal start to your day.
• You can easily store and recall of your favorite radio stations, up to 30 FM stations.
• Bass, middle, and treble can be adjusted to your taste.
 About this manual
• If an operation can be performed using either the buttons on the unit itself or from the remote control, the explanation will
focus on operation using the remote control.
•
indicates precautions for use of the unit and its feature limitations.
•
indicates supplementary explanations for better use.
Supplied accessories
Remote control
Speaker cable
(1.5 m (4.9') x 2)
Power cable
FM antenna
(use a CR2025 type
Lithium battery)
USB cap
Keep the USB cap out of
reach of children so as to
ensure that it is not
mistakenly swallowed.
1 En
NAMES OF PARTS AND THEIR FUNCTIONS
Top panel/Front panel
1
(Power)
5 USB port
Press to turn the unit on/off (standby).
There are two types of the standby state (☞ P. 5).
Connect your USB device (☞ P. 5, 8).
When the USB device is not in use, put the USB cap in
place to protect the connector.
2 SOURCE
Switch the audio source to be played.
Pressing this repeatedly will change the selection in the
following order.
CD USB FM BT AUX
6 PRESET /
Use these buttons to select a radio station that you’ve
stored (☞ P. 12, 13).
7
3 Audio control buttons
Use these to operate the CD/USB device.
: Play/Pause
: Stop
/ : Skip, Search backward/forward (press and hold
down)
4
(Eject button)
Eject the CD (cannot be operated while the option menu
(☞ P. 14) is displayed).
(Headphone jack)
Connect headphones.
8 Front panel display
The clock and other information is displayed.
9 VOLUME knob
Adjust the volume.
0 Disc tray
Set a disc. ( ☞ P. 7).
Front panel display
1 Alarm time
Indicates the alarm time (☞ P. 16).
2 Repeat/shuffle indicator
Displays the playback mode (☞ P. 8).
3 Multi-function indicator
Displays various information, including the clock time,
information about the currently-playing track, and the
frequency of the radio station.
2 En
4 Remote control signal receiver
Make sure that this sensor is not obstructed (☞ P. 5).
5 Alarm indicator
Turns on if the alarm has been set (☞ P. 16).
6 Sleep indicator
Turns on if the sleep timer has been set (☞ P. 15).
NAMES OF PARTS AND THEIR FUNCTIONS
Remote control
1 Remote control signal transmitter
2
(Power)
Press to turn the unit on/off (standby).
There are two types of the standby state (☞ P. 5).
3 Source buttons
Switch the audio source to be played. If you press one of
these while the unit is in standby (except ECO standby),
the unit will automatically turn on.
4 OPTION
Display the option menu (☞ P. 14).
5 Operation buttons
FOLDER /: Switch the playback folder and select
items or edit numerical values when
playing music on data CDs or USB
devices.
ENTER: Confirm a selected item or value.
: Stop*
: Play/Pause*
/
: Skip, Search backward/forward (press and hold
down)*
* Use these to operate the CD/USB device.
6 TUNING
/
Tune the radio (☞ P. 11, 12).
7 PRESET /
Select a radio station that you stored (☞ P. 12, 13).
8
(Repeat)/
(Shuffle)
Play music on a CD or USB device in repeat/shuffle
mode (☞ P. 8).
9 ALARM
Switch the alarm on/off (☞ P. 17).
0 SNOOZE/SLEEP
 Replacing the battery in the remote control
While pushing the release tab in direction
battery holder in direction .
, slide out the
Set the sleep timer or switch the alarm to snooze mode
(☞ P. 15, 17).
A DISPLAY
Switch the information shown in the front panel display
(☞ P. 7, 8, 11).
B MUTE
CR2025 type
Lithium battery
Mute or unmute the sound.
C VOLUME +/–
Adjust the volume.
D MEMORY
Store a radio station (☞ P. 12).
3 En
CONNECTIONS
Connecting the speakers and antenna
Connect the speakers and antenna.
Do not connect this unit’s power cable until you’ve finished connecting all cables.
If the radio reception is poor, try changing the height or direction or placement of the antenna to find a location that has better
reception.
If you use a commercially available outdoor antenna instead of the supplied antenna, reception may be better.
 Speakers
• You must peel off the insulation (covering) from the tip of the speaker cable to expose the conductor.
• Check the connections; make sure that left and right (L, R) and polarity (red: +, black: –) are connected correctly. If connections are
incorrect, the sound will be unnatural and the low frequencies may be insufficient. There might not be any sound at all if connections are
incorrect.
• Take care that the conductors of the speaker cable do not touch each other, and that the conductors do not touch any other metal part.
Such conditions can damage this unit or the speakers.
• Use only the supplied speakers. Using other speakers may result in unnatural sound.
• If you’re using this unit nearby a CRT display and you notice distorted color or noise in the display, move the speakers farther away from
the display.
 FM antenna
Fix the end of the FM antenna to a wall.
Connect the FM
antenna plug to the
rear panel FM
antenna terminal with
the side illustrated on
the left.
Reset button
(☞ P. 18)
4 En
Twist the bare wires
tightly so the individual
strands are not splayed.
CONNECTIONS
Connecting the power cable
When you’ve completed all connections, connect the
supplied power cable to AC IN, and then connect the plug of
the cable to an AC outlet.
Rear panel
To AC outlet
Other connections
 USB device
Connect your USB device to the USB port on the top panel.
For details on playable files, refer to “NOTES ON DISCS
AND USB DEVICES” (☞ P. 21).
The USB device is automatically charged when this unit is on or in
standby.
• Stop playback before disconnecting the USB device.
• Charging may not be possible depending on the USB device.
 External devices
Using a commercially available 3.5 mm stereo mini-plug
cable, connect your external device to the AUX jack on the
rear panel of this unit.
Rear panel
About the standby state
This unit has the following two types of standby state. Select the mode in POWER SAVING settings menu (☞ P. 14).
Mode
ECO standby*
(power saving mode)
Standby
Setting menu
(POWER
SAVING)
Clock display
Bluetooth
connection
Charging of USB
devices
Alarm setting
ECO
No clock display
Disable
Disable
Disable
NORMAL
Show
Enable
Enable
Enable
* Default setting
How to use the remote control
Within 6 m (20')
Battery insulation sheet: Remove before using.
5 En
ADJUSTING THE CLOCK (OPTION MENU)
You’ll use the option menu (☞ P. 14) to set this unit’s date and time.
1 Press
to turn the unit on.
2 Press OPTION.
1
The option menu will appear.
3 Press  /  to select “CLOCK SET,” and then
press ENTER.
2
3
The display will indicate “CLOCK YEAR,” and the
numerical value to be set will blink.
4
4 Set the date and time.
Press ▲/▼ to edit each numerical value, and then press
ENTER to confirm the setting.
Set the items in the order of year
month
day
hour
minute.
When clock setting has finished, the display will indicate
“Completed!”
The clock will be set to 0 second the moment you
complete the clock settings.
Clock display
Display (24-hour) when the unit is on
15:30
CD
Display (24-hour) when the unit is off (standby)*
• While making these settings, you can press DISPLAY to
select the time format (12-hour / 24-hour).
• If you decide to cancel without changing the setting, press
OPTION before confirming the change.
26
Apr
Jan
Feb
Mar
Apr
May
Jun
January
February
March
April
May
June
Nov
Dec
Jul
Aug
Sep
Oct
July
August
September
October
November December
* In ECO standby, the clock display will disappear.
6 En
The time settings will be reset if the unit remains unpowered for
about one hour.
LISTENING TO CD AND USB DEVICES
The unit will operate as follows when playing back tracks/files on CD/USB devices.
• If the CD/USB device being played is stopped, the track that you listened will start playback from the beginning of the
track the next time you play.
• If you press while playback is stopped, tracks will play as follows the next time playback begins:
 Audio CD: Play from the first track of the CD.
 Data CD*/USB device: Play from the first track of the folder contains the track you listened to last time.
• This unit automatically turns off (standby) if no operation has been performed for 20 minutes after CD/USB device
playback is stopped.
* “Data CD” is a CD that contains MP3/WMA files.
For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” (☞ P. 21).
Listening to a CD
1 Press the CD source button to switch the
audio source to CD.
1
If a CD is already set, playback will start.
2 Press the
(eject button) to open the disc tray.
3 Set a CD into the disc tray.
5
2 4
Set the CD with the label side facing upward.
4 Press the
tray.
3
(eject button) to close the disc
5 Press the
to start playback.
Playback can be controlled with either the remote
control, or the top panel on this unit (☞ P. 2, 3).
Folders and files on a data CD are played in alphabetical order.
 Skipping folders (remote control only)
While a data CD is playing, you can use the remote control’s
FOLDER ▲/▼ buttons to select the folder.
 Display information (remote control only)
The folder number (only for a data CD) or the song/file
number is shown for several seconds when starting playback
or skipping tracks.
If you press DISPLAY on the remote control while a song is
playing or paused, the information shown on the front panel
display will be switched in the following order.
- Elapsed song playback time
- Remaining song playback time (only for an audio CD)
- Song name*
- Album name*
- Artist name*
- File name (only for a data CD)
- Folder name (only for a data CD)
* Shown only if this data is included in the song.
7 En
LISTENING TO CD AND USB DEVICES
Listening to a USB device
1 Press the USB source button to switch the
audio source to USB.
1
If a USB device is already connected, playback will start.
2 Connect a USB device to the USB port.
Playback starts automatically.
Playback can be controlled with either the remote control,
or the top panel on this unit (☞ P. 2, 3).
2
Folders and files will play in the order in which they were written.
Stop playback before disconnecting the USB device.
 Skipping folders (remote control only)
While a USB device is playing, you can use the remote
control’s FOLDER ▲/▼ buttons to select the folder.
 Display information (remote control only)
The folder/file number is shown for several seconds when
starting playback or skipping tracks.
If you press DISPLAY on the remote control while a song is
playing or paused, the information shown on the front panel
display will be switched in the following order.
- Elapsed song playback time
- Song name*
- Album name*
- Artist name*
- File name
- Folder name
* Shown only if this data is included in the song.
Using repeat/shuffle playback (remote control only)
The playback status is shown by the repeat/shuffle indicator in the front panel display.
 Repeat playback
 Shuffle playback
Press
(repeat) repeatedly
to select one of the following
playback modes.
No display: Repeat mode off
: 1 track
: All tracks within the folder (data CD/USB device
only)
: All tracks
8 En
Press
(shuffle) repeatedly
to select one of the following
playback modes.
No display: Shuffle mode off
: All tracks within the folder (data CD/USB device
only)
: All tracks
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE
This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth device (mobile
phone, digital audio player, etc.). Please also refer to the owner’s manual of your Bluetooth device.
Playing back from your Bluetooth device
You’ll need to perform the pairing operation the first time you use your Bluetooth device with this unit, or if the pairing
settings have been deleted. Pairing is an operation that registers the Bluetooth device with this unit. Once pairing has been
completed, subsequent reconnection will be easy even after the Bluetooth connection is disconnected (☞ P. 10). If pairing is
not successful, refer to the item “Bluetooth” in “TROUBLESHOOTING” (☞ P. 20).
Yamaha does not guarantee all connections between this unit and Bluetooth device.
• This unit can be paired with up to 8 Bluetooth devices. When pairing with the 9th device has succeeded, pairing data for the device with the
oldest connection date will be deleted.
• While connecting to the Bluetooth device and perform the pairing with another device, the current Bluetooth connection will be canceled.
1 Press the BLUETOOTH source button for
more than 2 seconds to enter pairing mode.
1
• Pairing mode lasts for 5 minutes.
• In pairing mode, the front panel display of this unit will
indicate “BT Pairing...”.
You can also enter pairing mode by holding down SOURCE on
this unit.
3
15:30
BT Pairing OK
2 Perform Bluetooth pairing on the Bluetooth
device.
For details refer to the owner’s manual of the Bluetooth
device.
3 From the Bluetooth connection list of the
Bluetooth device, choose this unit (MCR-B020
Yamaha).
When pairing has been completed, the front panel display
of this unit will indicate “BT Pairing OK”.
If you are asked to enter a password, enter the numerals “0000”.
4 Connect this unit and the Bluetooth device via
Bluetooth.
5 Play back music from the Bluetooth device.
Take care that the volume setting of this unit is not too high. We
recommend that you adjust the volume on the Bluetooth device.
• If you connect via Bluetooth from the Bluetooth device while this
unit is in standby (except ECO standby), this unit will
automatically turn on.
• If you disconnect the Bluetooth connection from the Bluetooth
device while the audio source is set to Bluetooth, this unit will
automatically turn off (standby).
• If Bluetooth is selected as the audio source, this unit will
automatically turn off (standby) when 20 minutes have elapsed
without any Bluetooth connection nor any operation performed.
9 En
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE
Connecting an already-paired device via Bluetooth
Once pairing has been completed, connecting a Bluetooth will be easy the next time.
 Connecting from this unit
Press the BLUETOOTH source button to switch
the audio source to Bluetooth.
15:30
The Bluetooth indicator will blink in the front panel display;
this unit will search for the Bluetooth device that was most
recently connected via Bluetooth, and will then establish a
connection (You must first turn on the Bluetooth setting of
the Bluetooth device).
When the Bluetooth connection has been established, the
Bluetooth indicator will light, and the name of the Bluetooth
device will be displayed.
15:30
BT _____
 Connecting from the Bluetooth device
1 In the Bluetooth settings of the Bluetooth device, turn Bluetooth on.
2 From the Bluetooth connection list of the Bluetooth device, choose this unit (MCR-B020 Yamaha).
The Bluetooth connection will be established, and the front panel display of this unit will indicate the name of the
Bluetooth device.
Bluetooth connections cannot be established from the Bluetooth device when this unit is in ECO standby (☞ P. 5).
Disconnecting a Bluetooth connection
If any of the following operations are performed while a Bluetooth connection is being used, the Bluetooth connection will be
disconnected.
• Switch the audio source other than Bluetooth.
• Turn the unit off.
• Turn off the Bluetooth setting of the Bluetooth device.
10 En
LISTENING TO FM STATIONS
Selecting an FM station
To listen to the FM station, connect the antenna as described in “Connecting the speakers and antenna” (☞ P. 4).
1 Press the RADIO source button to switch the
audio source to FM.
2 Tune FM stations
1
2
Automatic tuning: Press and hold TUNING
/ .
Manual tuning: Press TUNING
/
repeatedly.
If you tune to a station manually while receiving FM, the sound
will be monaural.
 Display information (remote control only)
If you press DISPLAY on the remote control, the information shown on the front panel display will be switched in the
following order.
Reception status*
Preset number and frequency
* Example of reception status indication.
TUNED/STEREO: A strong FM stereo broadcast is
being received.
TUNED/MONO: A monaural FM broadcast is being
received (even if the FM broadcast is
stereo, reception will be monaural if
the signal is weak).
Not TUNED: No broadcast is being received.
Displaying Radio Data System information
(U.K. model only)
If you press DISPLAY on the remote control while Radio
Data System information is being received, the information
shown on the front panel display will be switched in the
following order.
- PS (Program Service)
- PTY (Program Type)
- RT (Radio Text)
- CT (Clock Time)
- Reception status
- Preset number and frequency
If the signal transmission of the Radio Data System station is too
weak, this unit may not be able to receive Radio Data System
information completely. In particular, RT (Radio Text) information
uses a lot of bandwidth, so it may be less available compared to
other types of information.
11 En
LISTENING TO FM STATIONS
Presetting FM stations (remote control only)
Use the preset function to store your favorite 30 stations.
First, press the RADIO source button to switch the audio source to FM.
 Auto preset
This method tunes automatically, and automatically presets only the stations that have good reception.
1 Press and hold down MEMORY.
1 2
“AUTO PRESET” will appear and “Press MEMORY”
will blink.
2 Press MEMORY.
Auto preset will begin.
When presetting has finished, the display will indicate
“Completed!”.
AUTO PRESET
Press MEMORY
When you perform auto preset, all stored stations are cleared
and the new stations are stored.
If you want to stop auto preset before it is completed, press
.
 Manual preset
1 Press TUNING /
you want to preset.
1
to tune a station that
2 Press MEMORY.
2 4
The display will indicate “PRESET MEMORY,” and the
preset number will blink.
3
3 Press PRESET / to select the preset
number that you want to store.
PRESETMEMORY
FM0187.50MHz
• The lowest preset number that has not been stored will be
selected first.
• If you want to cancel the presetting, press .
• If you select a preset number in which a station has already
been stored, it will be overwritten by the new station.
4 Press MEMORY.
When presetting has finished, the display will indicate
“Completed!”.
 Deleting a stored preset (Option menu)
1 Press OPTION.
The option menu will appear.
1 5
2 3
4
2 Press  /  to select PRESET DELETE, and
then press ENTER.
3 Press  /  to select the preset number that
you want to delete.
If you want to cancel the deleting, press OPTION.
4 Press ENTER to complete the operation.
When deleting has finished, the display will indicate
“Deleted!”.
5 Press OPTION to exit the option menu.
12 En
LISTENING TO FM STATIONS
Selecting preset FM stations
1 Press the RADIO source button to switch the
audio source to FM.
2 Press PRESET / to select the FM station
that you want to hear.
1
You can only select presets that have been stored.
2
LISTENING TO EXTERNAL SOURCES
Rear panel
1
1 Using a commercially available 3.5 mm stereo
mini-plug cable, connect your external device
to the AUX jack on the rear panel of this unit.
• Turn the unit off before connecting the audio cable.
• Turn down the volume of the unit and your external audio
device before connection.
2 Press
2
to turn the unit on.
3 Press the AUX source button to switch the
audio source to AUX.
4 Start playback on the connected external
audio device.
3
13 En
USEFUL FUNCTIONS
Using the Option menu
When you press OPTION, the option menu will appear in the front panel display, allowing you to make the following settings.
(eject button) cannot be operated while the option menu is displayed.
Option menu
Setting or range
See page
PRESET DELETE Deletes a stored preset (shown only if the audio source is FM).
12
DIMMER
–
Adjusts the brightness of the front panel display (1*1: bright, 2: medium, 3: dim).
EQ LOW
Adjusts the tonal character (low frequencies) (–10 -
- +10 dB).
–
EQ MID
Adjusts the tonal character (mid frequencies) (–10 - 0*1 - +10 dB).
–
EQ HIGH
Adjusts the tonal character (high frequencies) (–10 - 0*1 - +10 dB).
–
BALANCE
Adjusts the volume balance of the left and right speakers (L+10 - CENTER*1 - R+10).
–
0*1
POWER SAVING
Switches the standby state, NORMAL or
AUTO PWR
STDBY
You can specify the time after which the unit will turn off (standby) automatically.
If no operation occurs for the duration you specify, the unit will turn off (standby) automatically
(TIME 12H: 12 hours, TIME 8H*1: 8 hours, TIME 4H: 4 hours, TIME 2H: 2 hours, OFF: the unit
will not turn off (standby)).
–
CLOCK SET
Sets the date and time.
6
ALARM SET
Sets the alarm.
BLUETOOTH
*1
ECO*1
(power saving mode)
5
16
Connects this unit and your device via Bluetooth
(ON*1:
enable, OFF: disable).
9
Default setting
 Procedure for settings
1 Press OPTION.
The option menu will appear.
1 4
2 3
2 Press  /  to select the menu item that you
want to set, and then press ENTER.
3 Press  /  to edit the setting, and then press
ENTER to confirm the setting.
If you want to continue making other settings, repeat the
procedure from step 2 .
4 Press OPTION to exit the option menu.
If you decide to cancel without changing the setting, press
OPTION before confirming the change.
14 En
USEFUL FUNCTIONS
Using the sleep timer
When the specified time has elapsed, the unit will turn off automatically.
Press SNOOZE/SLEEP repeatedly to specify the
time after which the unit will turn off.
You can specify 30, 60, 90, 120 or OFF.
When you select a time, the sleep timer is turned on, and the
sleep indicator ( ) is shown in the front panel display.
If you press SNOOZE/SLEEP while the sleep timer is activated,
the sleep timer setting will be canceled.
Using the alarm function
The internal sound (melody) and then the selected audio source are played at the time set for the alarm.
If the selected audio source cannot be played back at the time set for the alarm, the internal sound is played back.
 Various audio sources
You can choose from audio CD, data CD, USB device, or FM. The following playback methods can also be selected
depending on the audio source:
Source
Audio CD
Data CD/USB device
FM
Playback
method
Selected track
Function
The selected track is played repeatedly.
Resume
The track you listened to last time is played back.
Folder
The selected folder is played repeatedly.
Resume
The track you listened to last time is played back.
Preset station
The selected preset station is played.
Resume
The FM station you listened to last time is played back.
You can not choose Bluetooth and AUX as the audio source.
 Snooze
The snooze function can be enabled to replay the alarm after 5 minutes (☞ P. 17).
15 En
USEFUL FUNCTIONS
Setting the alarm
 Setting the alarm time and alarm source (Option menu)
The alarm will not function when the unit is in ECO standby. To use the alarm function, set the Option menu item POWER SAVING to
NORMAL (☞ P. 14).
1 Press OPTION.
The option menu will appear.
2 Press  /  to select “ALARM SET”, and then press ENTER.
1
The alarm indicator (
2 3
) and numerical value you’re setting will blink.
3 Set the alarm.
Set items 1-3 described below.
Press  /  to select a numerical value, and press ENTER to confirm it.
Items
1 ALARM TIME
4
Alarm time
Setting or range
Make settings in the order of hours
minutes.
2 ALARM SOURCE CD: Play back music from a CD.
Specify the track number (data CD: folder
number) (RESUME*1, 1-99).
USB: Play back music from a USB device.
Specify the folder number (RESUME*1, 1-999).
FM: Play a FM station.
Specify the preset number (RESUME*1, 1-30).
9:12
Completed!
Alarm indicator
3 ALARM VOLUME Specifies the volume (5-60) of the alarm.
*1
If you choose RESUME when specifying the track/folder/preset number, the lastplayed track/folder/station will be played (resume playback)
4 Complete the settings.
When you set the VOLUME for item 3, the display will indicate
“Completed!” and your settings will be confirmed.
The alarm will be turned on and the alarm indicator (
) will light.
If you press OPTION or turn the unit off while making alarm settings, the settings will
be cancelled.
16 En
USEFUL FUNCTIONS
 Switching the alarm on/off
Press ALARM to turn the alarm on/off.
When the alarm is on, the alarm indicator (
) will light,
and the alarm time will be shown.
If you press ALARM again, the alarm indicator (
)
and the alarm will turn off.
If the Option menu item POWER SAVING is set to ECO,
the alarm will not function (☞ P. 14).
Operations while the alarm sound is playing
When the set time arrives, the set alarm sound will play. During playback, the following operations are available.
 To pause the alarm (Snooze)
Press SNOOZE/SLEEP.
Snooze will stop the alarm and play it again 5 minutes later.
• If you press SNOOZE/SLEEP while the alarm is activated, the
alarm sound will stop for about 5 minutes.
• Buttons on the unit other than the
will also function as the
snooze button.
 To turn the alarm off
Press ALARM or
.
• You can also stop the alarm by holding down SNOOZE/SLEEP.
• If you don’t stop the alarm, it will stop automatically after 60
minutes and the unit will turn off.
• The alarm setting will be saved even if the alarm is turned off.
If the alarm is turned on again by pressing ALARM, the alarm
will sound with the previous alarm settings.
17 En
TROUBLESHOOTING
If there is a problem with the unit, check the following list first. If you cannot resolve the problem with the suggested
solutions or if the problem is not listed below, turn off and unplug the unit, and consult the nearest authorized Yamaha dealer
or service center.
General
Problem
The speakers make no sound.
Cause
The volume might be set to the minimum level,
or muted.
Solution
Adjust the volume level.
The source may be incorrect.
Select the correct source.
The speakers may not be connected securely.
Check the connections (☞ P. 4).
Headphones are connected.
Remove the headphones.
The volume of a connected external device is not
loud enough.
Raise the volume of the external device.
The sleep timer may be set (☞ P. 15).
Turn the unit on and play the source again.
The auto power standby function may have
operated.
When the time specified for AUTO PWR STDBY in the
option menu has elapsed (☞ P. 14) or when 20 minutes
have elapsed without any operation being performed after
stopping USB device or CD playback, the unit will turn off
automatically.
Sound is cracked/distorted or
there is abnormal noise.
Input source volume is excessive, or volume of
this unit is excessive (especially Bass).
Adjust volume with VOLUME, or use the option menu
(☞ P. 14) to adjust the bass range. If an external device is
playing back, lower the volume of the external device.
The unit does not operate
properly.
The unit may have received a strong electrical
shock such as lightning or excessive static
electricity, or power supply may have dropped.
Press the reset button on the rear panel of the unit (☞ P. 4)
using a fine-tipped stick and restart the unit.
A digital or high-frequency
equipment produces noises.
The unit may be placed too close to the digital or
high-frequency equipment.
Place the unit farther away from the equipment.
The clock setting has been
cleared.
The unit remained unpowered for about one hour. Plug the power cable into the wall outlet firmly, and set the
clock again (☞ P. 6).
Alarm does not sound.
The unit is set to ECO standby.
In the option menu, set POWER SAVING to NORMAL
(☞ P. 14).
The auto power standby function may have
operated.
When the time specified for AUTO PWR STDBY in the
option menu has elapsed (☞ P. 14) or when 20 minutes
have elapsed without any operation being performed after
stopping USB device or CD playback, the unit will turn off
automatically.
Sound suddenly turns off.
The unit turns on but
immediately shuts off.
The front panel display indicates
“ALARM not work” and can’t
set the alarm.
The unit turns off unexpectedly.
Remote control
Problem
Cause
The remote control does not work The remote control may be operated outside its
properly.
operation range.
18 En
Solution
For information on the remote control operation range,
refer to “How to use the remote control” (☞ P. 5).
The remote control signal receiver on the unit
(☞ P. 2) may be exposed to direct sunlight or
lighting (inverted fluorescent lamps).
Change the lighting or orientation of the unit.
The battery may be worn out.
Replace the battery with a new one (☞ P. 3).
There are obstacles between the remote control
signal receiver on the unit (☞ P. 2) and the
remote control.
Remove the obstacles.
TROUBLESHOOTING
CD playback
Problem
Some button operations do not
work.
Playback does not start
immediately after pressing
(stops immediately).
The front panel display indicates
“no operation”, and the disc tray
does not open or close.
When you set a disc, the front
panel display indicates “CD No
Disc” or “CD Unknown.”
Cause
The disc set into the unit may not be compatible.
Solution
Use a disc supported by the unit (☞ P. 21).
The disc may be dirty.
Wipe the disc clean (☞ P. 21).
The disc set into the unit may not be compatible.
Use a disc supported by the unit (☞ P. 21).
If the unit was moved from a cold to warm place,
condensation may have formed on the disc
reading lens.
Wait for an hour or two until the unit adjusts to the room
temperature, and try again.
The option menu is displayed. Alternatively, the
alarm is playing.
Press OPTION to exit the option menu. Alternatively,
press ALARM to stop the alarm.
The disc set into the unit may not be compatible.
Use a disc supported by the unit (☞ P. 21).
The disc may be dirty, or a foreign object may
have adhered to it.
Wipe the disc clean. Alternatively, remove any foreign
object that has adhered to the disc (☞ P. 21).
The disc does not contain playable files.
Use a disc contains playable files (☞ P. 21).
The disc was set upside down.
Set the disc with the label facing upward.
USB device playback
Problem
Cause
Solution
MP3/WMA file in the USB device
does not play.
The USB device is not recognized.
Turn the unit off and reconnect the USB device to the unit.
If the solutions above do not resolve the problem, the USB
device is not playable on the unit (☞ P. 21).
The USB device does not contain playable files.
Use a USB device contains playable files (☞ P. 21).
When you connect a USB device,
the front panel display indicates
“USB OverCurrent,” and then
the front panel display goes
blank.
An incompatible USB device was connected to
the unit. Alternatively, the USB device is not
connect firmly to the unit.
Turn the unit off and reconnect the USB device to the unit.
If it does not resolve the problem, the USB device is not
playable on the unit (☞ P. 21).
19 En
TROUBLESHOOTING
Bluetooth
Problem
Cannot make this unit paired
with the Bluetooth device.
Cause
Solution
The Bluetooth device does not support A2DP.
Perform pairing operations with a device which supports
A2DP.
A Bluetooth adaptor, etc. that you want to pair
with this unit has a password other than “0000”.
Use a Bluetooth adaptor, etc. whose password is “0000”.
This unit and the Bluetooth device are too far
apart.
Move the Bluetooth device closer to this unit.
There is a device (microwave oven, wireless
LAN, etc.) outputs signals in the 2.4 GHz
frequency band nearby.
Move this unit away from the device that is emitting radiofrequency signals.
In the option menu, BLUETOOTH is set to OFF. In the option menu, set BLUETOOTH to ON (☞ P. 14).
Can’t establish a Bluetooth
connection.
This unit is not registered on the connection list
of the Bluetooth device.
Perform pairing operations again (☞ P. 9).
In the option menu, BLUETOOTH is set to OFF. In the option menu, set BLUETOOTH to ON (☞ P. 14).
No sound is produced or the
sound is interrupted during
playback.
The Bluetooth connection of this unit with the
Bluetooth device is disconnected.
Perform Bluetooth connection operations again (☞ P. 10).
This unit and the Bluetooth device are too far
apart.
Move the Bluetooth device closer to this unit.
There is a device (microwave oven, wireless
LAN, etc.) outputs signals in the 2.4 GHz
frequency band nearby.
Move this unit away from the device that is emitting radiofrequency signals.
The Bluetooth function of the Bluetooth device is
off.
Turn on the Bluetooth function of the Bluetooth device.
The Bluetooth device is not set to send Bluetooth
audio signals to this unit.
Check that the Bluetooth function of the Bluetooth device
is set properly.
The pairing setting of the Bluetooth device is not
set to this unit.
Set the pairing setting of the Bluetooth device to this unit.
The Bluetooth device’s volume is set to the
minimum.
Increase the volume level.
FM reception
Problem
Too much noise.
Cause
Solution
The antenna may be connected improperly.
Make sure the antenna is connected properly (☞ P. 4) or
use a commercially available outdoor antenna.
The antenna is too close to the unit or to an
electronic device.
Position the antenna as far away as possible from the unit
or the electronic device.
Too much noise during stereo
broadcast.
The radio station you selected may be far from
your area, or the radio wave reception is weak in
your area.
Try manual tuning to improve the signal quality (☞ P. 11)
or use a commercially available outdoor antenna.
Even with an outdoor antenna,
radio wave reception is weak.
(Sound is distorted.)
Multipath reflection or other radio interferences
may have occurred.
Change the height, direction, or placement of the antenna
(☞ P. 4).
20 En
NOTES ON DISCS AND USB DEVICES
CD information
This unit is designed for use with audio CD, CD-R*, and
CD-RW* with the logos followings.
* ISO 9660 format CD-R/RW
This unit can play back discs bearing any of the logo marks above.
A disc logo mark is printed on the disc and the disc jacket.
• Do not set any other type of disc into this unit. Doing so may
damage this unit.
• CD-R/RW cannot be played back unless finalized.
• Some discs cannot be played back depending on the disc
characteristics or recording conditions.
• Do not use any non-standard shaped discs such as a heart-shaped
disc.
• Do not use discs with many scratches on their surface.
• Do not set a cracked, warped, or glued disc.
Handling a disc
• Do not touch the surface of the
disc. Hold a disc by its edge (and
the center hole).
• Do not use a pencil or pointed
marker to write on the disc.
• Do not put a tape, seal, glue, etc., on a disc.
• Do not use a protective cover to prevent scratches.
• Do not set more than one disc into this unit at one time.
This can cause damage to both this unit and the discs.
• Do not put any foreign objects in the disc tray.
• Do not expose a disc to direct
sunlight, high temperature,
high humidity, or a lot of dust. Caution
USB device information
This unit supports USB mass storage class devices (e.g.,
flash memories or portable audio players) using FAT16 or
FAT32 format.
• Some devices may not work properly even if they meet the
requirements.
• Do not connect devices other than USB mass storage class
devices (such as USB chargers or USB hubs), PCs, card readers,
an external HDD, etc.
• Yamaha will not be held responsible for any damage to or data
loss on the USB device occurring while the device is connected
to this unit.
• Playability of and power supply to all kind of USB devices are
not guaranteed.
• USB devices with encryption cannot be used.
About MP3 or WMA files
• The unit can play back:
File
Bitrate (kbps)
Sampling
frequency (kHz)
MP3
8-320**
8-48
WMA
8-384**
8-48
** Both constant and variable bitrates are supported.
• The maximum numbers of files/folders that can be played on the
unit are as follows.
Data CD
USB
Maximum total number of file
512
3000
Maximum folder number
255
255
Maximum file number per folder
512
999
• Copyright-protected files cannot be played back.
• If a disc becomes dirty, wipe it
with a clean, dry cloth from the
center out to the edge. Do not
use record cleaner or paint
thinner.
• To avoid malfunction, do not
use a commercially available
lens cleaner.
21 En
SPECIFICATIONS
 PLAYER SECTION
 TUNER SECTION
CD
Tuning range
• Media ........................................................................... CD, CD-R/RW
• FM ...................................................................... 87.50 to 108.00 MHz
• Audio format.................................................. Audio CD, MP3, WMA
USB
 SPEAKER SECTION
• Audio format.....................................................................MP3, WMA
• Type ....................................................................Full range bass reflex
non magnetic shielding type
AUX
• Driver............................................................. 10 cm (4") cone type ×1
• Input connector ............................. 3.5 mm (1/8 ") STEREO mini jack
• Frequency response .......................................... 50 to 20 kHz (–10 dB)
 Bluetooth SECTION
• Dimensions (W × H × D)
................................. 120 (4-3/4") × 142 (5-5/8") × 258 (10-1/8") mm
• Bluetooth version .................................................................... Ver. 4.0
• Supported profile ......................................................... A2DP, AVRCP
• Weight ......................................................................... 1.3 kg (2.9 lbs.)
• Supported codecs .......................................................................... SBC
 GENERAL
• Wireless output ........................................................ Bluetooth Class 2
• Power supply ................................................... AC100-240V, 50/60Hz
• Maximum communication distance ......... 10 m (without obstructions)
• Power consumption ......................................................................21 W
 AMPLIFIER SECTION
• Standby consumption
.................................. 3.5 W or less (NORMAL)/0.5 W or less (ECO)
• Maximum output power.......... 15 W + 15 W (6  1 kHz, 10 % THD)
• Headphones
.............. 3.5 mm (1/8 in) STEREO mini jack (Impedance 16 to 32 )
• Dimensions (W × H × D)
........................................ 180 (7-1/8") × 143 (5-5/8") × 279 (11") mm
• Weight ............................................................................ 1.8 kg (4 lbs.)
• Equalizer characteristics
EQ Low (Bass)/EQ Mid (Middle)/EQ High (Treble) .............. ±10 dB
Specifications are subject to change without notice.
LASER SAFETY
Bluetooth
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt to
service this device.
• Bluetooth is a technology for wireless communication between
devices within an area of about 10 meters (33 ft) employing the
2.4 GHz frequency band, a band which can be used without a
license.
• Bluetooth is a registered trademark of the Bluetooth SIG and is
used by Yamaha in accordance with a license agreement.
DANGER
This unit emits visible laser radiation when open. Avoid direct eye
exposure to beam. When this unit is plugged into the wall outlet,
do not place your eyes close to the opening of the disc tray and
other openings to look into inside.
22 En
Handling Bluetooth communications
• The 2.4 GHz band used by Bluetooth compatible devices is a
radio band shared by many types of equipment. While Bluetooth
compatible devices use a technology minimizing the influence of
Bluetooth devices using the same radio band, such influence may
reduce the speed or distance of communications and in some
cases interrupt communications.
• The speed of signal transfer and the distance at which
communication is possible differs according to the distance
between the communicating devices, the presence of obstacles,
radio wave conditions and the type of equipment.
• Yamaha does not guarantee all wireless connections between this
unit and devices compatible with Bluetooth function.
Information for Users on Collection and Disposal
of Old Equipment and Used Batteries
These symbols on the products, packaging, and/or
accompanying documents mean that used electrical
and electronic products and batteries should not be
mixed with general household waste.
For proper treatment, recovery and recycling of old
products and used batteries, please take them to
applicable collection points, in accordance with your
national legislation and the Directives 2002/96/EC
and 2006/66/EC.
By disposing of these products and batteries correctly,
you will help to save valuable resources and prevent
any potential negative effects on human health and the
environment which could otherwise arise from
inappropriate waste handling.
For more information about collection and recycling
of old products and batteries, please contact your local
municipality, your waste disposal service or the point
of sale where you purchased the items.
[Information on Disposal in other Countries
outside the European Union]
These symbols are only valid in the European Union.
If you wish to discard these items, please contact your
local authorities or dealer and ask for the correct
method of disposal.
Note for the battery symbol (bottom two
symbol examples):
This symbol might be used in combination with a
chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical
involved.
If there should be color blotching or noise when used near a
TV, move this unit away from the TV when using it.
Do not use this unit within 22 cm (9 inches) of persons with a
heart pacemaker implant or defibrillator implant.
Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside medical
facilities.
LASER
Type
Wave length
Output Power
Semiconductor laser GaAS/GaAlAs
785 nm
4.5 mW
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an appropriate
3 pin plug fitted. For details, refer to the instructions described
below.
The plug severed from the mains lead must be destroyed, as a plug
with bared flexible cord is hazardous if engaged in a live socket
outlet.
■ Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED.
Make sure that neither core is connected to the earth terminal
of the three pin plug.
The user shall not reverse engineer, decompile, alter, translate
or disassemble the software used in this unit, whether in part or
in whole. For corporate users, employees of the corporation
itself as well as its business partners shall observe the
contractual bans stipulated within this clause. If the stipulations
of this clause and this contract cannot be observed, the user
shall immediately discontinue using the software.
If you use a commercially available cable to connect your USB
or external device, make sure that the length is less than
3 meters (9.8 ft).
23 En
(at the end of this manual) Additional information
(à la fin de ce manuel) Complément d’informations
(am Ende dieser Anleitung) Zusätzliche Informationen
(i slutet av denna bruksanvisning) Ytterligare information
(in fondo al presente manuale) Información adicional
(al final de este manual) Informazioni addizionali
(aan het einde van deze handleiding) Aanvullende informatie
(? ????? ?????????? ???????????) ?????????????? ??????????
The laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
LASER RADIATION WHEN OPEN
CAUTION : INVISIBLE
DO NOT STARE INTO BEAM
DANGER :
INVISIBLE LASER RADIATION WHEN OPEN
AVOID DIRECT EXPOSURE TO THE BEAM
LASER RADIATION WHEN OPEN
CAUTION : INVISIBLE
DO NOT STARE INTO BEAM
DANGER :
24 En
INVISIBLE LASER RADIATION WHEN OPEN
AVOID DIRECT EXPOSURE TO THE BEAM
Printed in China AV17-0048
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising