KINO-9452 User Manual v1.0
KINO-9452 Motherboard
KINO-9452 Motherboard User Manual
Page 1
KINO-9452 Motherboard
REVISION HISTORY
Title
KINO-9452 Intel Core Duo/Core Solo Motherboard
Revision Number
Description
Date of Issue
1.0
Initial release
September 2006
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event is the manufacturer liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
IBM PC is a registered trademark of International Business Machines Corporation. INTEL
is a registered trademark of INTEL Corporation. AMI is registered trademarks of American
Megatrends Inc. Other product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page 2
KINO-9452 Motherboard
Table of Contents
1
INTRODUCTION................................................................................................... 15
1.1 KINO-9452 OVERVIEW ........................................................................................... 16
1.1.1 KINO-9452 Benefits......................................................................................... 16
1.1.2 KINO-9452 Features........................................................................................ 16
1.2 KINO-9452 BOARD OVERVIEW............................................................................... 17
1.2.1 KINO-9452 Connectors ................................................................................... 17
1.2.2 Technical Specifications................................................................................... 18
2
DETAILED SPECIFICATIONS ........................................................................... 21
2.1 OVERVIEW ............................................................................................................... 22
2.2 DIMENSIONS ............................................................................................................ 22
2.2.1 Board Dimensions............................................................................................ 22
2.2.2 External Interface Panel Dimensions .............................................................. 23
2.3 CPU SUPPORT.......................................................................................................... 23
2.3.1 Intel® Core™ Duo ........................................................................................... 23
2.3.2 Intel® Core™ Solo ........................................................................................... 24
2.4 ON-BOARD CHIPSETS ............................................................................................... 25
2.4.1 Northbridge and Southbridge Chipsets ........................................................... 25
2.4.2 Intel 945GM Northbridge Chipset ................................................................... 25
2.4.3 Intel ICH7-M Southbridge Chipset.................................................................. 26
2.5 GRAPHICS SUPPORT ................................................................................................. 26
2.6 MEMORY SUPPORT ................................................................................................... 27
2.7 PCI BUS INTERFACE SUPPORT.................................................................................. 27
2.8 GBE ETHERNET ....................................................................................................... 27
2.9 DRIVE INTERFACES .................................................................................................. 28
2.9.1 SATA Drives ..................................................................................................... 28
2.9.2 IDE Interfaces.................................................................................................. 28
2.10 SERIAL PORTS ........................................................................................................ 29
2.11 REAL TIME CLOCK ................................................................................................. 29
2.12 USB INTERFACES................................................................................................... 29
2.13 BIOS ..................................................................................................................... 29
2.14 OPERATING TEMPERATURE AND TEMPERATURE CONTROL ..................................... 29
Page 3
KINO-9452 Motherboard
2.15 AUDIO CODEC ........................................................................................................ 30
2.16 POWER CONSUMPTION ........................................................................................... 31
2.17 PACKAGED CONTENTS AND OPTIONAL ACCESSORY ITEMS ..................................... 32
2.17.1 Package Contents........................................................................................... 32
2.17.2 Optional Accessory Items............................................................................... 32
3
CONNECTORS AND JUMPERS ......................................................................... 33
3.1 PERIPHERAL INTERFACE CONNECTORS .................................................................... 34
3.1.1 KINO-9452 Layout........................................................................................... 34
3.1.2 Peripheral Interface Connectors ..................................................................... 34
3.1.3 Rear Panel Connectors .................................................................................... 36
3.1.4 On-board Jumpers ........................................................................................... 36
3.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 37
3.2.1 Fan Connectors................................................................................................ 37
3.2.2 Front Panel Audio Connector.......................................................................... 38
3.2.3 Front Panel Connector .................................................................................... 39
3.2.4 Digital Input/Output Connector....................................................................... 41
3.2.5 IDE Connector ................................................................................................. 42
3.2.6 LCD Backlight Connector................................................................................ 43
3.2.7 LVDS LCD connector ...................................................................................... 44
3.2.8 Mini PCI Slot ................................................................................................... 46
3.2.9 Power Connector ............................................................................................. 48
3.2.10 14-Pin Serial Port Connectors....................................................................... 49
3.2.11 10-Pin Serial Port Connectors....................................................................... 50
3.2.12 SATA Drive Connectors ................................................................................. 51
3.2.13 SPDIF Connector........................................................................................... 53
3.2.14 Internal USB Connectors............................................................................... 54
3.3 EXTERNAL INTERFACE CONNECTORS ....................................................................... 55
3.3.1 Audio Connectors............................................................................................. 56
3.3.2 CRT Connector ................................................................................................ 57
3.3.3 Ethernet Connectors ........................................................................................ 58
3.3.4 Keyboard/Mouse Connector ............................................................................ 59
3.3.5 Serial Port Connectors .................................................................................... 60
3.3.6 TV-Out Connector ............................................................................................ 61
3.3.7 USB Connector ................................................................................................ 62
4
INSTALLATION AND CONFIGURATION ....................................................... 63
Page 4
KINO-9452 Motherboard
4.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 64
4.2 INSTALLATION CONSIDERATIONS ............................................................................. 64
4.2.1 Installation Notices .......................................................................................... 64
4.3 UNPACKING.............................................................................................................. 65
4.3.1 Unpacking Precautions.................................................................................... 65
4.3.2 Checklist........................................................................................................... 66
4.4 KINO-9452 MOTHERBOARD INSTALLATION ............................................................ 66
4.4.1 CPU Installation .............................................................................................. 67
4.4.2 Cooling Kit (CF-479B-RS ) Installation .......................................................... 69
4.4.3 DIMM Module Installation .............................................................................. 71
4.4.3.1 Purchasing the Memory Module............................................................... 71
4.4.3.2 DIMM Module Installation....................................................................... 71
4.4.4 Peripheral Device Connection......................................................................... 73
4.4.4.1 IDE Disk Drive Connector (IDE1) ........................................................... 73
4.4.4.2 COM Port Connectors............................................................................... 74
4.5 ON-BOARD JUMPERS ................................................................................................ 75
4.5.1 Clear CMOS Jumper........................................................................................ 76
4.5.2 COM2 Mode Selection..................................................................................... 77
4.5.3 LVDS LCD Voltage Selection........................................................................... 78
4.6 CHASSIS INSTALLATION ........................................................................................... 78
4.7 REAR PANEL CONNECTORS ...................................................................................... 79
4.7.1 LCD Panel Connection .................................................................................... 79
4.7.2 Ethernet Connection ........................................................................................ 79
4.7.3 USB Connection............................................................................................... 79
4.7.4 Serial Connection............................................................................................. 79
4.7.5 Keyboard and Mouse Connection.................................................................... 79
4.7.6 Audio Interface................................................................................................. 79
5
AMI BIOS SETUP.................................................................................................. 81
5.1 INTRODUCTION ........................................................................................................ 82
5.1.1 Starting Setup................................................................................................... 82
5.1.2 Using Setup ...................................................................................................... 82
5.1.3 Getting Help..................................................................................................... 83
5.1.4 Unable to Reboot after Configuration Changes .............................................. 83
5.1.5 BIOS Menu Bar................................................................................................ 83
5.2 MAIN ....................................................................................................................... 83
Page 5
KINO-9452 Motherboard
5.3 ADVANCED ............................................................................................................... 85
5.3.1 CPU Configuration.......................................................................................... 86
5.3.2 IDE Configuration ........................................................................................... 87
5.3.2.1 IDE Master, IDE Slave ............................................................................. 89
5.3.3 Super IO Configuration.................................................................................... 93
5.3.4 Hardware Health Configuration...................................................................... 96
5.3.5 ACPI Configuration ......................................................................................... 98
5.3.5.1 General ACPI Configuration..................................................................... 99
5.3.6 APM Configuration........................................................................................ 100
5.3.7 MPS Configuration ........................................................................................ 102
5.3.8 Remote Access Configuration ........................................................................ 103
5.3.9 USB Configuration......................................................................................... 105
5.3.9.1 USB Mass Storage Device Configuration............................................... 107
5.4 PCI/PNP ................................................................................................................ 109
5.5 BOOT ......................................................................................................................115
5.5.1 Boot Settings Configuration............................................................................115
5.5.2 Boot Device Priority .......................................................................................118
5.5.3 Removable Drives ...........................................................................................119
5.6 SECURITY............................................................................................................... 120
5.7 CHIPSET ................................................................................................................. 122
5.7.1 North Bridge Configuration........................................................................... 122
5.7.1.1 Video Function Configuration ................................................................ 125
5.7.2 South Bridge Configuration........................................................................... 128
5.8 EXIT ....................................................................................................................... 129
6
SOFTWARE DRIVERS ....................................................................................... 131
6.1 AVAILABLE SOFTWARE DRIVERS ............................................................................ 132
6.2 CHIPSET DRIVER INSTALLATION............................................................................. 132
6.3 VGA DRIVER ......................................................................................................... 135
6.4 BROADCOM LAN DRIVER (FOR GBE LAN) INSTALLATION .................................. 139
6.5 REALTEK HD AUDIO DRIVER (ALC883) INSTALLATION ....................................... 143
6.6 INTEL MATRIX STORAGE MANAGER INSTALLATION ............................................... 147
A
BIOS CONFIGURATION OPTIONS ................................................................ 151
A.1 BIOS CONFIGURATION OPTIONS........................................................................... 152
B
WATCHDOG TIMER .......................................................................................... 156
Page 6
KINO-9452 Motherboard
C
ADDRESS MAPPING.......................................................................................... 160
C.1 IO ADDRESS MAP ................................................................................................. 161
C.2 1ST MB MEMORY ADDRESS MAP ......................................................................... 161
C.3 IRQ MAPPING TABLE ............................................................................................ 162
C.4 DMA CHANNEL ASSIGNMENTS ............................................................................. 162
D
INDEX.................................................................................................................... 164
Page 7
KINO-9452 Motherboard
List of Figures
Figure 1-1: KINO-9452 Board Overview (Top View).................................................17
Figure 2-1: KINO-9452 Dimensions (mm) .................................................................22
Figure 2-2: External Interface Panel Dimensions (mm)...........................................23
Figure 3-1: Connector and Jumper Locations .........................................................34
Figure 3-2: Fan Connector Locations .......................................................................37
Figure 3-3: Front Panel Audio Connector Location.................................................38
Figure 3-4: Front Panel Connector Location............................................................40
Figure 3-5: GPIO Connector Location.......................................................................41
Figure 3-6: IDE Device Connector Location .............................................................42
Figure 3-7: LCD Backlight Connector Location .......................................................44
Figure 3-8: LVDS LCD Connector Location..............................................................45
Figure 3-9: Mini PCI Slot Location.............................................................................46
Figure 3-10: Power Connector Location ...................................................................48
Figure 3-11: 14-Pin Serial Port Connector Locations..............................................49
Figure 3-12: 10-Pin Serial Port Connector Locations..............................................50
Figure 3-13: SATA Drive Connector Locations........................................................52
Figure 3-14: SPDIF Connector Locations .................................................................53
Figure 3-15: Internal USB Connector Locations ......................................................55
Figure 3-16: KINO-9452 External Interface Connectors ..........................................56
Figure 3-17: Audio Connectors..................................................................................57
Figure 3-18: VGA Connector ......................................................................................57
Figure 3-19: RJ-45 Ethernet Connector ....................................................................58
Figure 3-20: PS/2 Pinouts...........................................................................................59
Figure 3-21: External Serial Port Connector ............................................................60
Figure 3-22: TV-Out Connector..................................................................................61
Figure 4-1: Make sure the CPU socket retention screw is unlocked .....................68
Figure 4-2: Lock the CPU Socket Retention Screw .................................................69
Figure 4-3: IEI CF-479B-RS Cooling Kit ....................................................................69
Figure 4-4: Securing the Cooling Kit.........................................................................70
Page 8
KINO-9452 Motherboard
Figure 4-5: Connect the cooling fan cable ...............................................................71
Figure 4-6: Installing the DIMM Module ....................................................................72
Figure 4-7: Locking the DIMM Module ......................................................................72
Figure 4-8: Connection of IDE Connector ................................................................74
Figure 4-9 Jumper
....................................................................................................75
Figure 4-10: Jumper Locations..................................................................................76
Figure 6-1: InstallShield Wizard Preparation Screen............................................ 133
Figure 6-2: Welcome Screen ................................................................................... 133
Figure 6-3: License Agreement............................................................................... 134
Figure 6-4: Readme Information ............................................................................. 134
Figure 6-5: Restart the Computer ........................................................................... 135
Figure 6-6: Starting Install Shield Wizard Screen ................................................. 136
Figure 6-7: Preparing Setup Screen ....................................................................... 136
Figure 6-8: VGA Driver Installation Welcome Screen........................................... 137
Figure 6-9: VGA Driver License Agreement .......................................................... 137
Figure 6-10: VGA Driver Installing Notice.............................................................. 138
Figure 6-11: VGA Driver Installation Complete ..................................................... 138
Figure 6-12: Access Windows Control Panel........................................................ 139
Figure 6-13: Double Click the System Icon ........................................................... 140
Figure 6-14: Double Click the Device Manager Tab.............................................. 140
Figure 6-15: Device Manager List ........................................................................... 141
Figure 6-16: Search for Suitable Driver.................................................................. 141
Figure 6-17: Locate Driver Files.............................................................................. 142
Figure 6-18: Location Browsing Window............................................................... 142
Figure 6-19: Access Windows Control Panel........................................................ 143
Figure 6-20: Double Click the System Icon ........................................................... 144
Figure 6-21: Double Click the Device Manager Tab.............................................. 144
Figure 6-22: Device Manager List ........................................................................... 145
Figure 6-23: Search for Suitable Driver.................................................................. 146
Figure 6-24: Locate Driver Files.............................................................................. 147
Figure 6-25: Preparing Setup Screen ..................................................................... 148
Page 9
KINO-9452 Motherboard
List of Tables
Table 1-1: Technical Specifications ..........................................................................20
Table-2-1: Supported CPUs........................................................................................23
Table 2-2: Power Consumption .................................................................................31
Table 3-1: Peripheral Interface Connectors..............................................................35
Table 3-2: Rear Panel Connectors.............................................................................36
Table 3-3: On-board Jumpers ....................................................................................36
Table 3-4: Fan Connector Pinouts.............................................................................38
Table 3-5: Front Panel Audio Connector Pinouts ....................................................39
Table 3-6: Front Panel Connector Pinouts ...............................................................40
Table 3-7: GPIO Connector Pinouts ..........................................................................41
Table 3-8: IDE Connector Pinouts .............................................................................43
Table 3-9: LCD Backlight Connector Pinouts ..........................................................44
Table 3-10: LVDS LCD Connector Pinouts ...............................................................46
Table 3-11: Mini PCI Slot Pinouts ..............................................................................47
Table 3-12: Power Connector Pinouts ......................................................................49
Table 3-13: COM2 Pinouts..........................................................................................50
Table 3-14: COM3 and COM4 Pinouts .......................................................................51
Table 3-15: SATA Drive Connector Pinouts .............................................................52
Table 3-16: SPDIF Pinouts..........................................................................................54
Table 3-17: USB3 and USB4 Pinouts.........................................................................55
Table 3-18: VGA Connector Pinouts .........................................................................58
Table 3-19: LAN1 and LAN2 Pinouts .........................................................................58
Table 3-20: RJ-45 Ethernet Connector LEDs............................................................59
Table 3-21: PS/2 Connector Pinouts .........................................................................60
Table 3-22: External Serial Port Pinouts ...................................................................61
Table 3-23: TV-Out Pinouts ........................................................................................62
Table 3-24: External USB Connector Pinouts ..........................................................62
Table 4-1: IEI Provided Cables...................................................................................73
Table 4-2: On-board Jumpers ....................................................................................75
Page 10
KINO-9452 Motherboard
Table 4-3: Clear CMOS Jumper Settings ..................................................................77
Table 4-4: JP1 Jumper Settings.................................................................................77
Table 4-5: JP2 Jumper Settings.................................................................................78
Table 5-1: BIOS Navigation Keys...............................................................................83
Page 11
KINO-9452 Motherboard
List of BIOS Menus
BIOS Menu 1: Main ....................................................................................................84
BIOS Menu 2: Advanced.............................................................................................86
BIOS Menu 3: CPU Configuration..............................................................................87
BIOS Menu 4: IDE Configuration ...............................................................................88
BIOS Menu 5: IDE Master and IDE Slave Configuration..........................................90
BIOS Menu 6: Super IO Configuration ......................................................................93
BIOS Menu 7: Hardware Health Configuration.........................................................96
BIOS Menu 8: ACPI Configuration.............................................................................98
BIOS Menu 9: General ACPI Configuration [Advanced\ ACPI Configuration] ......99
BIOS Menu 10: APM Configuration ........................................................................ 100
BIOS Menu 11: MPS Configuration ........................................................................ 103
BIOS Menu 12: Remote Access Configuration [Advanced] ................................ 104
BIOS Menu 13: USB Configuration......................................................................... 105
BIOS Menu 14: USB Mass Storage Device Configuration.................................... 108
BIOS Menu 15: PCI/PnP Configuration .................................................................. 110
BIOS Menu 16: Boot................................................................................................. 115
BIOS Menu 17: Boot Settings Configuration......................................................... 116
BIOS Menu 18: Boot Device Priority Settings ....................................................... 119
BIOS Menu 19: Removable Drives.......................................................................... 120
BIOS Menu 20: Security........................................................................................... 121
BIOS Menu 21: Chipset............................................................................................ 122
BIOS Menu 22: North Bridge Chipset Configuration............................................ 123
BIOS Menu 23:South Bridge Chipset Configuration ............................................ 128
BIOS Menu 24:Exit ................................................................................................. 129
Page 12
KINO-9452 Motherboard
Glossary
AC ’97
Audio Codec 97
HDD
Hard Disk Drive
ACPI
Advanced Configuration and
IDE
Integrated Data Electronics
Power Interface
I/O
Input/Output
APM
Advanced Power Management
ICH4
I/O Controller Hub 4
ARMD
ATAPI Removable Media Device
L1 Cache Level 1 Cache
ASKIR
Shift Keyed Infrared
L2 Cache Level 2 Cache
ATA
Advanced Technology
LCD
Liquid Crystal Display
Attachments
LPT
Parallel Port Connector
BIOS
Basic Input/Output System
LVDS
Low Voltage Differential Signaling
CFII
Compact Flash Type 2
MAC
Media Access Controller
CMOS
Complementary Metal Oxide
OS
Operating System
Semiconductor
PCI
Peripheral Connect Interface
CPU
Central Processing Unit
PIO
Programmed Input Output
Codec
Compressor/Decompressor
PnP
Plug and Play
COM
Serial Port
POST
Power On Self Test
DAC
Digital to Analog Converter
RAM
Random Access Memory
DDR
Double Data Rate
SATA
Serial ATA
DIMM
Dual Inline Memory Module
S.M.A.R.T Self Monitoring Analysis and
DIO
Digital Input/Output
DMA
Direct Memory Access
SPD
Serial Presence Detect
EIDE
Enhanced IDE
S/PDI
Sony/Philips Digital Interface
EIST
Enhanced Intel SpeedStep
SDRAM
Synchronous Dynamic Random
Reporting Technology
Access Memory
Technology
FDD
Floppy Disk Drive
SIR
Serial Infrared
FDC
Floppy Disk Connector
UART
Universal Asynchronous
FFIO
Flexible File Input/Output
FIFO
First In/First Out
USB
Universal Serial Bus
FSB
Front Side Bus
VGA
Video Graphics Adapter
IrDA
Infrared Data Association
Receiver-transmitter
Page 13
KINO-9452 Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 14
IEI® Technology, Corp.
KINO-9452 Motherboard
Chapter
1
1 Introduction
Page 15
KINO-9452 Motherboard
1.1 KINO-9452 Overview
The Mini-ITX form factor KINO-9452 with Intel® Core™2 Duo / Core™ Solo CPU platform
is fully equipped with latest technology and advanced multi-mode I/Os. The KINO-9452 is
designed for system manufacturers, integrators, and VARs that want performance,
reliability, and quality at a reasonable price.
1.1.1 KINO-9452 Benefits
Some of the KINO-9452 benefits include:
Dual-core Intel® processor support
o
o
Two physical cores in a package share the system load
Each core has its own L1 cache and shares the L2 cache to enhance the
processing speed
o
High performance levels especially in 3D graphic and multi media
application
Independent dual audio with HDTV output
Excellent thermal control that enhance voltage efficiency and supports cooler
and quieter systems
Mini PCI expansion slot and rich I/O interface
o
o
Integrates a PCI and a mini PCI slot for flexible expansion capabilities
Integrates TV-out and multi channel audio for related applications
DDR2 memory technology supported
SATA II with 3.0Gb/s transfer rate
Dual PCIe GbE enhance high performance in network
1.1.2 KINO-9452 Features
Some of the KINO-9452 features are listed below:
Complies with RoHS
Supports Intel® Core™2 Duo, Core™ Duo and Core™ Solo processor
Supports a maximum front side bus (FSB) speed up to 667MHz
Supports up to 2GB of 400MHz, 533MHz or 667MHz of DDR2 memory
Comes with dual Broadcom BCM5787 for PCIe GbE
Supports two SATA II channels with transfer rates up to 3.0Gb/s
Page 16
IEI® Technology, Corp.
KINO-9452 Motherboard
Supports eight USB 2.0 devices
Supports HDTV-Out, dual 18 channel LVDS and CRT
1.2 KINO-9452 Board Overview
Figure 1-1: KINO-9452 Board Overview (Top View)
1.2.1 KINO-9452 Connectors
The KINO-9452 has the following connectors on-board:
2 x DDR2 DIMM sockets
1 x Digital I/O connector
3 x Fan connectors
1 x Front panel audio connector
1 x Front panel connector
Page 17
KINO-9452 Motherboard
1 x IDE Interface connector
1 x LCD backlight connector
1 x LVDS LCD connector
1 x Mini PCI slot
1 x PCI slot
1 x Power connector
3 x Serial port connectors
2 x SATA II connectors
1 x SPDIF connector
2 x USB connectors
The KINO-9452 has the following connectors on the board rear panel:
6 x Audio jacks
1 x CRT connector
2 x Ethernet connectors
1 x Keyboard/Mouse connector
1 x Serial port connector
1 x TV-Out port
4 x USB 2.0 ports
The KINO-9452 has the following on-board jumpers:
Clear CMOS
COM2 mode selection (RS-232/422/485)
LVDS LCD voltage selection
The location of these connectors on the motherboard can be seen in Figure 1-1. These
connectors are fully described in Chapter 3.
1.2.2 Technical Specifications
KINO-9452 technical specifications are listed in Table 1-1. Detailed descriptions of each
specification can be found in Chapter 2 Detailed Specifications.
Page 18
IEI® Technology, Corp.
KINO-9452 Motherboard
SPECIFICATION
CPUs Supported
Intel® Core™2 Duo/ Core™ Duo/Core™ Solo with
533/667MHz FSB
Chipsets
Northbridge: Intel 945GM
Southbridge: ICH7-M
I/O Controller
ICH7-M
Graphics Support
Intel Gen 3.5 Integrated Graphics Engine
Display
CRT
HDTV:
MacroVision support / Overscaling / Component,
S-Video and Composite output
480P / 720P / 1080i / 1080P and NTSC / PAL
support
LVDS: Dual channel 18-bit LVDS
Memory
Dual channel DDR2 400/533/667MHz memory modules
(Max. 2GB)
PCI Bus Interface
33MHz, Revision 2.3
Serial ATA (SATA)
Two SATA II connectors with 3.0Gb/s transfer rates
HDD Interface
One IDE channel support two Ultra ATA 100 devices
USB Interfaces
Eight USB 2.0 connectors supported
Serial Ports
Four COM ports
Extension
One Mini PCI slot
One PCI slot
Super I/O
ITE8712
Digital I/O
8 bit digital I/O, 4 input / 4 output by super I/O
Audio
REALTEK ALC883 with 7.1 channel HD interface with 2
audio streams support
Page 19
KINO-9452 Motherboard
Ethernet
Dual Broadcom BCM5787 for PCI Express GbE with
ASF2.0 remote control support
BIOS
AMI BIOS Label
Power
ATX power
Physical Dimensions
170mm x 170mm (width x length)
Operating
Minimum: 0ºC (32°F)
Temperature
Maximum: 60°C (140°F)
Table 1-1: Technical Specifications
Page 20
IEI® Technology, Corp.
KINO-9452 Motherboard
Chapter
2
2 Detailed Specifications
Page 21
KINO-9452 Motherboard
2.1 Overview
This chapter describes the specifications and on-board features of the KINO-9452 in
detail.
2.2 Dimensions
2.2.1 Board Dimensions
The dimensions of the board are shown in Figure 2-1.
Figure 2-1: KINO-9452 Dimensions (mm)
Page 22
IEI® Technology, Corp.
KINO-9452 Motherboard
2.2.2 External Interface Panel Dimensions
External interface panel dimensions are shown in Figure 2-2.
Figure 2-2: External Interface Panel Dimensions (mm)
2.3 CPU Support
Table-2-1 lists the CPUs supported by the KINO-9452 board.
Model
Clock Speed
L2 Cache
Max. FSB
Socket
Intel® Core™2 Duo
1.66 to 2.33 GHz
2MB/4MB
667 MHz
479
Intel® Core™ Duo
1.20 to 2.33 GHz
2 MB
667 MHz
479
Intel® Core™ Solo
1.06 to 1.83 GHz
2 MB
667 MHz
479
Table-2-1: Supported CPUs
2.3.1 Intel® Core™2 Duo
The Intel® Core™2 Duo processor comes with the following features:
Dual core processor with enhanced performance
Intel® 64 architecture
Supports Intel Architecture with Dynamic Execution
On-die, primary 32-kB instruction cache and 32-kB write-back data cache per
core
On-die, up to 4-MB second level shared cache with Advanced Transfer Cache
Architecture
Data Prefetch Logic
Page 23
KINO-9452 Motherboard
667-MHz, Source-Synchronous FSB for Standard Voltage processors
Advanced Power Management features including Enhanced Intel
SpeedStep® Technology
Intel Enhanced Deeper Sleep state and Dynamic Cache Sizing
2.3.2 Intel® Core™ Duo
The Intel® Core™ Duo processor comes with the following features:
Two complete execution cores in one processor package provide
advancements in simultaneous computing
Dual-core processing efficiently delivers performance while balancing power
requirements
Two execution cores share a high-performance, power-optimized 667 MHz
front-side bus (FSB) to access the same chipset memory.
Enhanced Intel SpeedStep® technology allows a system to dynamically
adjust processor voltage and core frequency, decreasing average power
consumption and average heat production
Intel® Smart Cache Design allows two execution cores to share 2 MB of L2
cache, reducing FSB traffic and enhancing system responsiveness
Intel® Advanced Thermal Manager supports new digital temperature sensors
and thermal monitors on each execution core to enhance thermal monitoring
accuracy
Streaming SIMD Extensions 3 (SSE3) provides significant performance
enhancement for multi-media applications
Embedded lifecycle support protects system investment by enabling
extended product availability for embedded and communications customers
2.3.3 Intel® Core™ Solo
The Intel® Core™ Solo processor comes with the following features:
Supports Intel Architecture with Dynamic Execution
On-die, primary 32-KB instruction cache and 32-KB write-back data cache
On-die, 2-MB second level cache with Advanced Transfer Cache Architecture
Streaming SIMD Extensions 2 (SSE2) and Streaming SIMD Extensions 3
(SSE3)
Page 24
IEI® Technology, Corp.
KINO-9452 Motherboard
Advanced power management features including Enhanced Intel
SpeedStep® technology
Execute Disable Bit support for enhanced security
Intel Virtualization Technology enhances virtualization robustness and
performance
2.4 On-board Chipsets
2.4.1 Northbridge and Southbridge Chipsets
The following chipsets are preinstalled on the board:
Northbridge: Intel® 945GM
Southbridge: Intel® ICH7-M
The following two sections (Section 2.4.2 and Section 2.4.3) list some of the features of
the Intel 945GM and the Intel ICH7-M chipsets. For more information on these two
chipsets please refer to the Intel website.
2.4.2 Intel 945GM Northbridge Chipset
The Intel 945GM northbridge chipset comes with the following features:
System Memory Support
o
o
o
o
o
Supports single/dual-channel DDR2 SDRAM
64-bit wide per channel
256-MB, 512-MB and 1-Gb memory technologies supported
Support for DDR2 On-Die Termination (ODT)
Support for 2N timings only
Internal Graphics
o
o
Intel Gen 3.5 Integrated Graphics Engine
250 MHz core render clock and 200 MHz core display clock at 1.05 V
core voltage
o
Supports TV-Out, LVDS, CRT and SDVO
DMI
o
o
o
Chip-to-chip interface between (G)MCH and ICH
Configurable as x2 or x4 DMI lanes
DMI lane reversal support
Page 25
KINO-9452 Motherboard
o
32-bit downstream address
Power Management
o
o
o
ACPI S0, S3, S4, S5
CPU States C0, C1, C2, C3, C4 states
Rapid Memory Power Mgmt
2.4.3 Intel ICH7-M Southbridge Chipset
The Intel ICH7-M southbridge chipset comes with the following features:
PCI Local Bus Specification, Revision 2.3 support for 33 MHz PCI operations
(supports up to six Req/Gnt pairs)
ACPI Power Management Logic support
Enhanced DMA controller, interrupt controller, and timer functions
Integrated Serial ATA host controller with independent DMA operation on two
ports and AHCI
Integrated IDE controller supports Ultra ATA 100/66/33
USB host interface with support for eight USB ports; four UHCI host controller;
one EHCI high-speed USB 2.0 Host controller
Supports Audio Codec ’97, Revision 2.3 Specification
Supports Intel High Definition Audio
Supports Intel Matrix Storage Technology
Supports Intel Active Management Technology
Low Pint Count (LPC) interface
Firmware Hub (FWH) interface support
Serial Peripheral Interface (SPI) support
2.5 Graphics Support
The graphics features listed below are all integrated on the Intel 945GM northbridge
chipset.
Analog CRT
o
o
o
Integrated 400 MHz RAMDAC
Analog monitor support up to QXGA
Support for CRT hot plug
LVDS
Page 26
IEI® Technology, Corp.
KINO-9452 Motherboard
o
o
Panel support up to UXGA (1600 x 1200)
25 MHz – 112 MHz single-/dual-channel; @18bpp – TFT panel type
supported
o
o
o
o
o
o
Pixel Dithering for 18-bit TFT panel to emulate 24-bpp true color displays
Panel Fitting. Panning, and Center Mode supported
CPIS 1.5 compliant
Spread spectrum clocking supported
Panel Power Sequencing support
Integrated PWM interface for LCD backlight inverter control
TV-Out
o
o
o
o
o
o
Three integrated 10-bit DACS
MacroVision support
Overscaling
NTSC/PAL
Component, S-Video and Composite Output interfaces
HDTV support – 480p/720p/1080i/1080p
SDVO Ports
o
o
o
Concurrent operation of x1 PCIe with SDVO
Two SDVO ports supported
Supports appropriate external SDVO components (DVI, LVDS, TV-Out)
2.6 Memory Support
The KINO-9452 has two DDR2 DIMM sockets and supports two 400MHz, 533MHz or
667MHz DDR2 DIMM with a maximum RAM of up to 2GB.
2.7 PCI Bus Interface Support
The PCI bus on the KINO-9452 has the following features:
33MHz Revision 2.3 is implemented
Six PCI REQ/GNT pairs is available
64-bit addressing on PCI using DAC protocol is supported
2.8 GbE Ethernet
The BCM5787 is a seventh generation 10/100/1000BASE-T Ethernet LAN controller
solution for high performance network applications. The device combines a triple-speed
Page 27
KINO-9452 Motherboard
IEEE 802.3 compliant Media Access Controller (MAC) with a triple-speed Ethernet
transceiver, PCIe bus interface, and on-chip buffer memory in a single device. The device
is fabricated in a 1.2V CMOS process providing a low-power system solution. The GbE
controller features are below.
Integrated 10/100/1000 transceiver
10/100/1000 full/half-duplex MAC
Automatic MDI crossover function
Supports PCIe v1.0a
Wake-on-LAN support meeting the ACPI requirements
Statistics for SNMP MIB II, Ethernet-like MIB and Ethernet MIB (802.3z,
clause 30)
Serial EEPROM or serial flash supported
JTAG supported
196-FBGA package
2.9 Drive Interfaces
The KINO-9452 can support the following drive interfaces.
2 x SATA drives
2 x IDE devices
2.9.1 SATA Drives
The KINO-9452 supports two SATA II drives with transfer rates of up to 3.0Gb/s.
2.9.2 IDE Interfaces
The KINO-9452 southbridge chipset IDE controller supports up to two IDE devices with
the following specifications:
Supports PIO IDE transfers up to 16MB/s
Supports Ultra ATA 100 devices with data transfer rates up to 100MB/s
Page 28
IEI® Technology, Corp.
KINO-9452 Motherboard
2.10 Serial Ports
The KINO-9452 has four high-speed UART serial ports, configured as COM1, COM2,
COM3 and COM4. The serial ports have the following specifications.
16C550 UART with 16-byte FIFO buffer
115.2Kbps transmission rate
2.11 Real Time Clock
256-byte battery backed CMOS SRAM
2.12 USB Interfaces
The KINO-9452 supports eight USB interfaces, four internal and four external. The USB
interfaces support USB 2.0.
2.13 BIOS
The KINO-9452 uses a licensed copy of AMI BIOS. The features of the flash BIOS used
are listed below:
SMIBIOS (DMI) compliant
Console redirection function support
PXE (Pre-Boot Execution Environment ) support
USB booting support
2.14 Operating Temperature and Temperature Control
The maximum and minimum operating temperatures for the KINO-9452 are listed below.
Minimum Operating Temperature: 0ºC (32°F)
Maximum Operating Temperature: 60°C (140°F)
A cooling fan and heat sink must be installed on the CPU. Thermal paste must be
smeared on the lower side of the heat sink before it is mounted on the CPU. Heat sinks
are also mounted on the northbridge and southbridge chipsets to ensure the operating
temperature of these chips remain low.
Page 29
KINO-9452 Motherboard
2.15 Audio Codec
The KINO-9452 has an integrated REALTEK ALC883 CODEC. The ALC883 CODEC is a
Value 7.1+2 Channel High Definition Audio (HDA) codecs. The ALC883 series provide 10
DAC channels that simultaneously support 7.1 sound playback, plus 2 channels of
independent stereo sound output (multiple streaming) through the front panel stereo
output. Some of the features of the codec are listed below.
High-performance DACs with 95dB SNR (A-Weighting), ADCs with 85dB
SNR (A-Weighting)
Meets performance requirements for audio on PC2001 systems and Microsoft
WLP 2.x
Ten DAC channels support 16/20/24-bit PCM format for 7.1 sound playback,
plus 2 channels of independent stereo sound output (multiple streaming)
through the front panel output
2 stereo ADCs support 16/20/24-bit PCM format, one for stereo microphone,
the other for legacy mixer recording
All DACs support 44.1k/48k/96k/192kHz sample rate
All ADCs support 44.1k/48k/96kHz sample rate
16/20/24-bit S/PDIF-OUT supports 44.1k/48k/96k/192kHz sample rate
16/20/24-bit S/PDIF-IN supports 44.1k/48k/96kHz sample rate
Up to four channels of microphone array input are supported for AEC/BF
application
High-quality analog differential CD input
Supports external PCBEEP input and built-in digital BEEP generator
Software selectable 2.5V/3.75V VREFOUT
Two jack detection pins, each designed to detect up to 4 jacks
Reserve analog mixer architecture for backward compatibility with AC'97
Wide range (–80dB ~ +42dB) volume control with 1.5dB resolution of analog
to analog mixer gain
All analog jacks are stereo input and output re-tasking for analog plug & play
Built-in headphone amplifiers for each re-tasking jack
2 GPIOs (General Purpose Input/Output) for customized applications
Power support: Digital: 3.3V; Analog: 3.0V~5.0V (Minimum AVDD is 3.0V)
Pin compatible with the ALC880 and ALC882
Enhanced S/PDIF-IN circuitry ensures compatibility with consumer DVD
Page 30
IEI® Technology, Corp.
KINO-9452 Motherboard
players
48-pin LQFP 'Green' package
Meets Microsoft WHQL/WLP 2.x audio requirements
EAX™ 1.0 & 2.0 compatible
Direct Sound 3D™ compatible
A3D™ compatible
I3DL2 compatible
HRTF 3D Positional Audio
Emulation of 26 sound environments to enhance gaming experience
10-Band Software Equalizer
Voice Cancellation and Key Shifting in Karaoke mode
Realtek Media Player
Enhanced Configuration Panel to improve user experience
Microphone Acoustic Echo Cancellation (AEC), Noise Suppression (NS), and
Beam Forming (BF) technology for voice application
ALC883D features optional Dolby® Digital Live output for consumer
equipment
ALC883DTS features optional DTS® Connect software
2.16 Power Consumption
Table 2-2 shows the power consumption parameters for the KINO-9452 when an Intel
Core Duo processor with a clock speed of 2.16GHz is running with two DDR2 1GB DIMM
modules.
Voltage
Current
+5V
1.58A
+12V
2.05A
+3.3V
3.12A
5VSB
0.32A
Table 2-2: Power Consumption
Page 31
KINO-9452 Motherboard
2.17 Packaged Contents and Optional Accessory Items
2.17.1 Package Contents
The KINO-9452 is shipped with the following components.
1 x KINO-9452 single board computer
1 x IDE flat cable
2 x SATA cables
1 x SATA power cable
2 x RS-232 cables
1 x HDTV out cable
1 x I/O shielding
1 x Mini jumper pack
1 x Utility CD
1 x Quick Installation Guide
2.17.2 Optional Accessory Items
The items shown in the list below are optional accessory items are purchased separately.
CPU cooler
USB cable
RS-232/422/485 cable
Page 32
IEI® Technology, Corp.
KINO-9452 Motherboard
Chapter
3
3 Connectors and
Jumpers
Page 33
KINO-9452 Motherboard
3.1 Peripheral Interface Connectors
Section 3.1.1 shows peripheral interface connector locations. Section 3.1.2 lists all the
peripheral interface connectors seen in Section 3.1.1.
3.1.1 KINO-9452 Layout
Figure 3-1 shows the on-board peripheral connectors, backplane peripheral connectors
and on-board jumpers.
Figure 3-1: Connector and Jumper Locations
3.1.2 Peripheral Interface Connectors
Table 3-1 shows a list of the peripheral interface connectors on the KINO-9452. Detailed
descriptions of these connectors can be found in Section 3.2.
Page 34
IEI® Technology, Corp.
KINO-9452 Motherboard
Connector
Type
Label
DDR2 DIMM socket
240-pin slot
DIMM1
DDR2 DIMM socket
240-pin slot
DIMM2
Fan connector (CPU)
3-pin header
CPU_FAN1
Fan connector (System)
3-pin header
SYS_FAN1
Fan connector (Northbridge)
3-pin header
NB_FAN1
Front panel connector
14-pin header
F_PANEL1
Front panel audio connector
10-pin header
AUDIO2
Digital Input/Output connector
10-pin header
DIO1
IDE Interface connector
40-pin header
IDE1
LCD backlight connector
6-pin header
CN1
LVDS LCD connector
30-pin header
LVDS1
Mini PCI slot
124-pin Mini PCI Type III slot
MINIPCI
PCI slot
124-pin PCI slot
PCI2
Power connector
20-pin connector
PWR1
Serial port connector (1)
14-pin header
COM2
Serial port connector (2)
10-pin header
COM3
Serial port connector (3)
10-pin header
COM4
SATA drive connector (1)
7-pin SATA connector
SATA1
SATA drive connector (2)
7-pin SATA connector
SATA2
SPDIF connector
5-pin header
SPDIF1
USB connector (1)
8-pin header
USB4
USB connector (2)
8-pin header
USB5
Table 3-1: Peripheral Interface Connectors
Page 35
KINO-9452 Motherboard
3.1.3 Rear Panel Connectors
Table 3-2 lists the rear panel connectors on the KINO-9452. Detailed descriptions of these
connectors can be found in Section 3.3.
Connector
Type
Label
Audio Jacks
Audio connector
AUDIO1
CRT connector
15-pin female connector
CRT_COM1
Ethernet connector (1)
RJ-45 connector
LAN/USB1A
Ethernet connector (2)
RJ-45 connector
LAN/USB2A
Keyboard/Mouse connector
6-pin mini din connector
KBMS1
Serial port connector
DB-9 male connector
CRT_COM1
TV-Out port
7-pin TV port
TV
USB 2.0 port (1)
USB port connector
LAN/USB1B
USB 2.0 port (2)
USB port connector
LAN/USB2B
Table 3-2: Rear Panel Connectors
3.1.4 On-board Jumpers
Table 3-3 lists the on-board jumpers. Detailed descriptions of these jumpers can be found
in Section 4.5.
Description
Label
Type
Clear CMOS
JP3
3-pin header
COM2 mode selection
JP1
3-pin header
LVDS LCD voltage selection
JP2
6-pin header
Table 3-3: On-board Jumpers
Page 36
IEI® Technology, Corp.
KINO-9452 Motherboard
3.2 Internal Peripheral Connectors
Internal peripheral connectors are found on the motherboard and are only accessible
when the motherboard is outside of the chassis. This section has complete descriptions of
all the internal, peripheral connectors on the KINO-9452.
3.2.1 Fan Connectors
CN Label:
CPU_FAN1, SYS_FAN1 and NB_FAN1
CN Type:
3-pin header
CN Location:
See Figure 3-2
CN Pinouts:
See Table 3-4
The cooling fan connectors on the KINO-9452 provide a 12V, 500mA current to one CPU
cooling fan, one system cooling fan and one Northbridge cooling fan. There is a “sense”
pin in the fan connector, which transfers the fan’s sense signal to the system BIOS in
order to recognize the fan speed. Please note that only some specific types of fans offer a
rotation signal.
Figure 3-2: Fan Connector Locations
Page 37
KINO-9452 Motherboard
PIN NO.
DESCRIPTION
1
GND
2
+12V
3
Sense
Table 3-4: Fan Connector Pinouts
3.2.2 Front Panel Audio Connector
CN Label:
AUDIO2
CN Type:
10-pin header (2x5)
CN Location:
See Figure 3-3
CN Pinouts:
See Table 3-5
The front panel audio connector connect the on-board sound system of the KINO-9452 to
the audio line out and microphone jacks on the front of the computer chassis.
Figure 3-3: Front Panel Audio Connector Location
Page 38
IEI® Technology, Corp.
KINO-9452 Motherboard
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1.
Port1_L
2.
GND
3.
Port1_R
4.
PRESENCE
5.
Port2_R
6.
SENSE1_RETUR
7.
SENSE_SEND
8.
(KEY)
9.
Port2_L
10.
SENSE2_RETUR
Table 3-5: Front Panel Audio Connector Pinouts
3.2.3 Front Panel Connector
CN Label:
F_PANEL1
CN Type:
14-pin header (2x7)
CN Location:
See Figure 3-4
CN Pinouts:
See Table 3-6
The front panel connector connects to several external switches and indicators to monitor
and control the motherboard. These indicators and switches include:
Power
Power button
Reset button
Speaker
HDD
Page 39
KINO-9452 Motherboard
Figure 3-4: Front Panel Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
Power LED+
2
Speaker+
3
NC
4
NC
5
Power LED-
6
NC
7
Power Button#
8
Speaker-
9
Power Button
10
NC
11
IDE LED+
12
Reset Button
13
IDE LED-
14
Reset Button#
Table 3-6: Front Panel Connector Pinouts
Page 40
IEI® Technology, Corp.
KINO-9452 Motherboard
3.2.4 Digital Input/Output Connector
CN Label:
DIO1
CN Type:
10-pin header (2x6)
CN Location:
See Figure 3-5
CN Pinouts:
See Table 3-7
The DIO connector is managed through a Super I/O chip. The DIO connector pins are
user programmable. The digital IO port of KINO-9452 is 5V CMOS level.
Figure 3-5: GPIO Connector Location
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
GND
2
+5V
3
INPUT0
4
OUTPUT0
5
INPUT1
6
OUTPUT1
7
INPUT2
8
OUTPUT2
9
INPUT3
10
OUTPUT3
Table 3-7: GPIO Connector Pinouts
Page 41
KINO-9452 Motherboard
3.2.5 IDE Connector
CN Label:
IDE1
CN Type:
40-pin header (2x20)
CN Location:
See Figure 3-6
CN Pinouts:
See Table 3-8
One primary 40-pin IDE device connector on the KINO-9452 motherboard supports
connectivity to ATA 100 IDE devices with data transfer rates up to 100MB/s.
Figure 3-6: IDE Device Connector Location
PIN NO.
Page 42
DESCRIPTION
PIN NO.
DESCRIPTION
1
RESET#
2
GND
3
DATA 7
4
DATA 8
5
DATA 6
6
DATA 9
7
DATA 5
8
DATA 10
9
DATA 4
10
DATA 11
11
DATA 3
12
DATA 12
13
DATA 2
14
DATA 13
IEI® Technology, Corp.
KINO-9452 Motherboard
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
15
DATA 1
16
DATA 14
17
DATA 0
18
DATA 15
19
GND
20
(KEY)
21
DRQ
22
GND
23
IOW#
24
GND
25
IOR#
26
GND
27
CHRDY
28
GND
29
DACK
30
GND
31
INTERRUPT
32
N/C
33
SA1
34
P66DET
35
SA0
36
SA2
37
HDC CS0#
38
HDC CS1#
39
HDD ACTIVE#
40
GND
Table 3-8: IDE Connector Pinouts
3.2.6 LCD Backlight Connector
CN Label:
CN1
CN Type:
6-pin header (1x6)
CN Location:
See Figure 3-7
CN Pinouts:
See Table 3-9
The LCD backlight connector is for the LCD inverter connection.
Page 43
KINO-9452 Motherboard
Figure 3-7: LCD Backlight Connector Location
PIN NO.
DESCRIPTION
1
Back Light Power
2
Back Light Power
3
Back Light enable
4
NC
5
GND
6
GND
Table 3-9: LCD Backlight Connector Pinouts
3.2.7 LVDS LCD connector
CN Label:
LVDS1
CN Type:
30-pin connector (2x15)
Page 44
IEI® Technology, Corp.
KINO-9452 Motherboard
CN Location:
See Figure 3-8
CN Pinouts:
See Table 3-10
The connector supports one or two channel (18 or 36bit) LVDS panel.
Figure 3-8: LVDS LCD Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
GND
3
1st LVDS data0 output +
4
1st LVDS data0 output -
5
1st LVDS data1 output +
6
1st LVDS data1 output -
7
1st LVDS data2 output +
8
1st LVDS data2 output -
9
1st LVDS clock output +
10
1st LVDS clock output -
11
NC
12
NC
13
GND
14
GND
15
2nd LVDS data0 output +
16
2nd LVDS data0 output -
Page 45
KINO-9452 Motherboard
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
17
2nd LVDS data1 output +
18
2nd LVDS data1 output -
19
2nd LVDS data2 output +
20
2nd LVDS data2 output -
21
2nd LVDS clock output +
22
2nd LVDS clock output -
23
NC
24
NC
25
GND
26
GND
27
+LCD (3.3V, 5V or 12V)
28
+LCD (3.3V, 5V or 12V)
29
+LCD (3.3V, 5V or 12V)
30
+LCD (3.3V, 5V or 12V)
Table 3-10: LVDS LCD Connector Pinouts
3.2.8 Mini PCI Slot
CN Label:
MINIPCI
CN Type:
124-pin Mini PCI Type III slot
CN Location:
See Figure 3-9
CN Pinouts:
See Table 3-11
Mini PCI is a small form factor version of a PCI card. Mini PCI expansion devices can be
inserted into the Mini PCI slot.
Figure 3-9: Mini PCI Slot Location
Page 46
IEI® Technology, Corp.
KINO-9452 Motherboard
PIN
NAME
PIN
NAME
PIN
NAME
PIN
NAME
1
TIP
32
GROUND
63
3.3V
94
AD[02]
2
RING
33
AD[31]
64
FRAME#
95
AD[03]
3
8PMJ-3
34
PME#
65
CLKRUN#
96
AD[00]
4
8PMJ-1
35
AD[29]
66
TRDY#
97
5V
5
8PMJ-6
36
RESERVED
67
SERR#
98
RESERVED_WIP5
6
8PMJ-2
37
GROUND
68
STOP#
99
AD[01]
7
8PMJ-7
38
AD[30]
69
GROUND
100
RESERVED_WIP5
8
8PMJ-4
39
AD[27]
70
3.3V
101
GROUND
9
8PMJ-8
40
3.3V
71
PERR#
102
GROUND
10
8PMJ-5
41
AD[25]
72
DEVSEL#
103
AC_SYNC
11
LED1_GRNP
42
AD[28]
73
C/BE[1]#
104
M66EN
12
LED2_YELP
43
RESERVED
74
GROUND
105
AC_SDATA_IN
13
LED1_GRNN
44
AD[26]
75
AD[14]
106
AC_SDATA_OUT
14
LED2_YELN
45
C/BE[3]#
76
AD[15]
107
AC_BIT_CLK
15
CHSGND
46
AD[24]
77
GROUND
108
AC_CODEC_ID0#
16
RESERVED
47
AD[23]
78
AD[13]
109
AC_CODEC_ID1#
17
INTB#
48
IDSEL
79
AD[12]
110
AC_RESET#
18
5V
49
GROUND
80
AD[11]
111
MOD_AUDIO_MON
19
3.3V
50
GROUND
81
AD[10]
112
RESERVED
20
INTA#
51
AD[21]
82
GROUND
113
AUDIO_GND
21
RESERVED
52
AD[22]
83
GROUND
114
GROUND
22
RESERVED
53
AD[19]
84
AD[09]
115
SYS_AUDIO_OUT
23
GROUND
54
AD[20]
85
AD[08]
116
SYS_AUDIO_IN
24
3.3VAUX
55
GROUND
86
C/BE[0]#
117
SYS_AUDIO_OUT GND
25
CLK
56
PAR
87
AD[07]
118
SYS_AUDIO_IN GND
26
RST#
57
AD[17]
88
3.3V
119
AUDIO_GND
27
GROUND
58
AD[18]
89
3.3V
120
AUDIO_GND
28
3.3V
59
C/BE[2]#
90
AD[06]
121
RESERVED
29
REQ#
60
AD[16]
91
AD[05]
122
MPCIACT#
30
GNT#
61
IRDY#
92
AD[04]
123
VCC5VA
31
3.3V
62
Ground
93
RESERVED
124
3.3VAUX
Table 3-11: Mini PCI Slot Pinouts
Page 47
KINO-9452 Motherboard
3.2.9 Power Connector
CN Label:
PWR1
CN Type:
20-pin connector
CN Location:
See Figure 3-10
CN Pinouts:
See Table 3-12
This 20-pin power connector supports the ATX power supply.
Figure 3-10: Power Connector Location
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
Page 48
1
3.3V
11
3.3V
2
3.3V
12
-12V
3
GND
13
GND
IEI® Technology, Corp.
KINO-9452 Motherboard
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
4
+5V
14
PS_ON
5
GND
15
GND
6
+5V
16
GND
7
GND
17
GND
8
Power good
18
-5V
9
5VSB
19
+5V
10
+12V
20
+5V
Table 3-12: Power Connector Pinouts
3.2.10 14-Pin Serial Port Connectors
CN Label:
COM2
CN Type:
14-pin header (2x7)
CN Location:
See Figure 3-11
CN Pinouts:
See Table 3-13
The serial ports connectors connect to RS-232/422/485 serial port device.
Figure 3-11: 14-Pin Serial Port Connector Locations
Page 49
KINO-9452 Motherboard
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTS
7
DTR
8
RI
9
GND
10
NC
11
TX+
12
TX-
13
RX+
14
RX-
Table 3-13: COM2 Pinouts
3.2.11 10-Pin Serial Port Connectors
CN Label:
COM3 and COM4
CN Type:
10-pin header (2x5)
CN Location:
See Figure 3-12
CN Pinouts:
See Table 3-14
The serial ports connectors connect to RS-232 serial port device.
Figure 3-12: 10-Pin Serial Port Connector Locations
Page 50
IEI® Technology, Corp.
KINO-9452 Motherboard
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTS
7
DTR
8
RI
9
GND
10
NC
Table 3-14: COM3 and COM4 Pinouts
3.2.12 SATA Drive Connectors
CN Label:
SATA1 and SATA2
CN Type:
1x7 pin SATA drive connectors
CN Location:
See Figure 3-13
CN Pinouts:
See Table 3-15
The two SATA drive connectors are connected to four SATA II drives. SATA II drives
transfer data at speeds as high as 3.0Gb/s.
Page 51
KINO-9452 Motherboard
Figure 3-13: SATA Drive Connector Locations
PIN NO.
DESCRIPTION
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
Table 3-15: SATA Drive Connector Pinouts
Page 52
IEI® Technology, Corp.
KINO-9452 Motherboard
3.2.13 SPDIF Connector
CN Label:
SPDIF1
CN Type:
5-pin header (1x5)
CN Location:
See Figure 3-14
CN Pinouts:
See Table 3-16
The SPDIF connector connects to the S/PDIF audio module, which bears S/PDIF digital
output. S/PDIF (Sony/Philips Digital Interface) is a newest audio transfer file format, which
allows the user to enjoy digital audio. The SPDIF1 port provides digital audio to external
speaker or compressed AC3 data to an external Dolby Digital Decoder via a coaxial cable.
Figure 3-14: SPDIF Connector Locations
Page 53
KINO-9452 Motherboard
PIN NO.
DESCRIPTION
1
+5V
2
(KEY)
3
SPDIF_OUT
4
GND
5
SPDIF_IN
Table 3-16: SPDIF Pinouts
3.2.14 Internal USB Connectors
CN Label:
USB4 and USB5
CN Type:
8-pin header (2x4)
CN Location:
See Figure 3-15
CN Pinouts:
See Table 3-17
One 2x4 pin connector provides connectivity to two USB 2.0 ports. The USB ports are
used for I/O bus expansion.
Page 54
IEI® Technology, Corp.
KINO-9452 Motherboard
Figure 3-15: Internal USB Connector Locations
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
VCC
2
GND
3
DATA0-
4
DATA1+
5
DATA0+
6
DATA1-
7
GND
8
VCC
Table 3-17: USB3 and USB4 Pinouts
3.3 External Interface Connectors
The peripheral connectors on the back panel are connected to devices externally when
the KINO-9452 is installed in a chassis. The peripheral connectors on the rear panel are:
6 x Audio jacks
1 x CRT connector
2 x RJ-45 Ethernet connectors
1 x Keyboard/mouse connector
Page 55
KINO-9452 Motherboard
1 x Serial port connector
1 x TV-Out connector
4 x USB 2.0 connectors
Figure 3-16: KINO-9452 External Interface Connectors
3.3.1 Audio Connectors
CN Label:
AUDIO1
CN Type:
Audio jack
CN Location:
See Figure 3-16 (labeled number 7)
CN Pinouts:
See Figure 3-17
Center/Subwoofer port (Yellow): Connects the center/subwoofer speakers.
Line In port (Light Blue): Connects a CD-ROM, DVD player, or other audio
devices.
Rear Speaker Out port (Black): Connects the rear speakers in a
4/6/8-channel audio configuration.
Line Out port (Lime): Connects a headphone or a speaker. In 4,6,8-channel
configuration, the function of this port becomes Front Speaker Out.
Side Speaker Out port (Gray): Connectors the side speakers in an
8-channel audio configuration.
Page 56
IEI® Technology, Corp.
KINO-9452 Motherboard
Microphone (Pink): Connects a microphone.
Figure 3-17: Audio Connectors
3.3.2 CRT Connector
CN Label:
CRT_COM1
CN Type:
15-pin female connector
CN Location:
See Figure 3-16 (labeled number 9)
CN Pinouts:
See Table 3-18
The standard 15-pin VGA connector connects to a CRT or LCD display monitor.
Figure 3-18: VGA Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
RED
2
GREEN
3
BLUE
4
N/C
5
GND
6
GND
7
GND
8
GND
9
VCC
10
GND
Page 57
KINO-9452 Motherboard
11
N/C
12
DDC DAT
13
HSYNC
14
VSYNC
15
DDC CLK
Table 3-18: VGA Connector Pinouts
3.3.3 Ethernet Connectors
CN Label:
LAN/USB1A and LAN/USB2A
CN Type:
RJ-45
CN Location:
See Figure 3-16 (labeled number 4 and 6)
CN Pinouts:
See Table 3-19
The KINO-9452 is equipped with two built-in GbE Ethernet controllers. The controllers can
connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the
connector indicating the status of LAN. The pin assignments are listed in the following
table:
PIN
DESCRIPTION
PIN
DESCRIPTION
1
MDX0+
5
MDX2-
2
MDX0-
6
MDX1-
3
MDX1+
7
MDX3+
4
MDX2+
8
MDX3-
Table 3-19: LAN1 and LAN2 Pinouts
Figure 3-19: RJ-45 Ethernet Connector
Page 58
IEI® Technology, Corp.
KINO-9452 Motherboard
The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green
LED indicates activity on the port and the yellow LED indicates the port is linked. See
Table 3-20.
SPEED LED
STATUS
DESCRIPTION
ACT/LINK LED
STATUS
DESCRIPTION
OFF
10Mbps connection
OFF
No link
ORANGE
100Mbps connection
YELLOW
Linked
GREEN
1Gbps connection
BLINKING
Data Activity
Table 3-20: RJ-45 Ethernet Connector LEDs
3.3.4 Keyboard/Mouse Connector
CN Label:
KBMS1
CN Type:
PS/2 connector
CN Location:
See Figure 3-16 (labeled number 1)
CN Pinouts:
See Table 3-21
The KINO-9452 keyboard and mouse connectors are standard PS/2 connectors.
Figure 3-20: PS/2 Pinouts
Page 59
KINO-9452 Motherboard
PIN
DESCRIPTION
PIN
DESCRIPTION
1
L_KDAT
7
L_MDAT
2
NC
8
NC
3
GND
9
GND
4
5V
10
5V
5
L_KCLK
11
L_MCLK
6
NC
12
NC
Table 3-21: PS/2 Connector Pinouts
3.3.5 Serial Port Connectors
CN Label:
CRT_COM1
CN Type:
DB-9
CN Location:
See Figure 3-16 (labeled number 2)
CN Pinouts:
See Table 3-22
The serial ports can be connected to a serial communications device directly.
Figure 3-21: External Serial Port Connector
Page 60
PIN
Description
1
DATA CARRIER DETECT (DCD)
2
RECEIVE DATA (RXD)
3
TRANSMIT DATA (TXD)
IEI® Technology, Corp.
KINO-9452 Motherboard
4
DATA TERMINAL READY (DTR)
5
GROUND (GND)
6
DATA SET READY (DSR)
7
REQUEST TO SEND (RTS)
8
CLEAR TO SEND (CTS)
9
RING INDICATOR (RI)
Table 3-22: External Serial Port Pinouts
3.3.6 TV-Out Connector
CN Label:
TV
CN Type:
7-pin TV port
CN Location:
See Figure 3-16 (labeled number 8)
CN Pinouts:
See Table 3-23
The TV-Out port connects to a TV.
Figure 3-22: TV-Out Connector
PIN
Description
1
Ground
2
Ground
3
S-Vidio Luminance
Component:Luminance (Y)
4
S-Vidio:Chrominance
Component:Chrominance (Pr)
Page 61
KINO-9452 Motherboard
5
NC
6
Ground
7
Composite:CVBS
Component:Chrominance (Pb)
Table 3-23: TV-Out Pinouts
3.3.7 USB Connector
CN Label:
LAN/USB1B and LAN/USB2B
CN Type:
USB port
CN Location:
See Figure 3-16 (labeled number 3 and 5)
CN Pinouts:
See Table 3-24
USB devices can be connected directly to the USB connectors on the rear panel.
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
VCC
5
VCC
2
USBD0-
6
USBD1-
3
USBD0+
7
USBD1+
4
GND
8
GND
Table 3-24: External USB Connector Pinouts
Page 62
IEI® Technology, Corp.
KINO-9452 Motherboard
Chapter
4
4 Installation and
Configuration
Page 63
KINO-9452 Motherboard
4.1 Anti-static Precautions
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the KINO-9452. (Dry climates are especially susceptible to ESD.) It is therefore
critical that whenever the KINO-9452 (or any other electrical component) is handled, the
following anti-static precautions are strictly adhered to.
Wear an anti-static wrist band: Wearing a simple anti-static wrist band can
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
4.2 Installation Considerations
NOTE:
The following installation notices and installation considerations should be
read and understood before the motherboard is installed. All installation
notices pertaining to the installation of the motherboard should be strictly
adhered to. Failing to adhere to these precautions may lead to severe
damage of the motherboard and injury to the person installing the
motherboard.
4.2.1 Installation Notices
Before and during the installation of the KINO-9452, please do the following:
Read the user manual
o
The user manual provides a complete description of the KINO-9452,
installation instructions and configuration options.
Wear an electrostatic discharge cuff (ESD)
o
Electronic components are easily damaged by ESD. Wearing an ESD cuff
removes ESD from the body and helps prevent ESD damage.
Place the motherboard on an antistatic pad
Page 64
IEI® Technology, Corp.
KINO-9452 Motherboard
o
When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.
Turn off all power to the KINO-9452
o
When working with the motherboard, make sure that it is disconnected
from all power supplies and that no electricity is being fed into the system.
Before and during the installation of the KINO-9452 DO NOT:
remove any of the stickers on the PCB board. These stickers are required for
warranty validation.
use the product before verifying all the cables and power connectors are
properly connected.
allow screws to come in contact with the PCB circuit, connector pins, or its
components.
4.3 Unpacking
NOTE:
If any of the items listed below are missing when the KINO-9452 is
unpacked, do not proceed with the installation and contact the KINO-9452
reseller or vendor.
4.3.1 Unpacking Precautions
Before installing the KINO-9452, unpack the motherboard. Some components on
KINO-9452 are very sensitive to static electricity and can be damaged by a sudden rush of
power. To protect it from being damaged, follow these precautions:
The user should ground them self to remove any static charge before
touching the KINO-9452. To do so wear a grounded wrist strap at all times or
frequently touch any conducting materials that is connected to the ground.
Handle the KINO-9452 by its edges. Do not touch the IC chips, leads or
circuitry if not necessary.
Page 65
KINO-9452 Motherboard
Do not place a PCB on top of an anti-static bag. Only the inside of the bag is safe from
static discharge.
4.3.2 Checklist
When unpacking the KINO-9452, please make sure that the package contains the
following items.
1 x KINO-9452 single board computer
1 x IDE flat cable
2 x SATA cables
1 x SATA power cable
2 x RS-232 cables
1 x HDTV out cable
1 x I/O shielding
1 x Mini jumper pack
1 x Utility CD
1 x Quick Installation Guide
CPU cooler (optional)
USB cable (optional)
RS-232/422/485 cable (optional)
If one or more of these items are missing, please contact the reseller or vendor the
KINO-9452 was purchased from and do not proceed any further with the installation.
4.4 KINO-9452 motherboard Installation
WARNING!
1. Never run the motherboard without an appropriate heat sink and cooler
that can be ordered from IEI Technology or purchased separately.
2. Be sure to use the CPU 12V power connector for the CPU power.
WARNING!
Please note that the installation instructions described in this manual should
Page 66
IEI® Technology, Corp.
KINO-9452 Motherboard
be carefully followed in order to avoid damage to the motherboard components
and injury to the user.
WARNING!
When installing electronic components onto the motherboard always take the
following anti-static precautions in order to prevent ESD damage to the
motherboard and other electronic components like the CPU and DIMM
modules
The following components must be installed onto the motherboard or connected to the
motherboard during the installation process.
CPU
CPU cooling kit
DDR2 memory modules
Peripheral device connection
4.4.1 CPU Installation
WARNING!
CPUs are expensive and sensitive components. When installing the CPU
please be careful not to damage it in anyway. Make sure the CPU is installed
properly and ensure that a heat sink and CPU cooling fan is properly installed
before the motherboard is run or else both the CPU and the board may be
damaged.
To install an Intel 479-pin CPU onto the motherboard, follow the steps below:
Step 1: Is the CPU retention screw in an unlocked position? When shipped, the
retention screw of the CPU socket should be in the unlocked position. If it is not
in the unlocked position, use a screwdriver to position it in an unlocked position.
(See Figure 4-1)
Page 67
KINO-9452 Motherboard
Figure 4-1: Make sure the CPU socket retention screw is unlocked
Step 2: Inspect the CPU socket. Make sure there are no bent pins and make sure the
socket contacts are free of foreign material. If any debris is found, remove it with
compressed air.
Step 3: Correctly position the CPU. Make sure the pin 1 mark matches the cut edge
on the CPU socket. Carefully place the CPU on top of the socket. When properly
placed, the CPU should be easily inserted into the socket.
Step 4: Insert the CPU. To insert the CPU into the socket, hold the CPU by its edges
and follow the instructions below:
Step 5: Correctly orientate the CPU with the IHS (Integrated Heat Sink) side facing
upward.
Step 6: Locate the pin 1 mark on the CPU.
Step 7: Gently insert the CPU into the socket.
Step 8: Rotate the retention screw into the locked position. (See Figure 4-2) Step 0:
Page 68
IEI® Technology, Corp.
KINO-9452 Motherboard
Figure 4-2: Lock the CPU Socket Retention Screw
4.4.2 Cooling Kit (CF-479B-RS ) Installation
Figure 4-3: IEI CF-479B-RS Cooling Kit
IEI provides a cooling kit designed for socket 479 CPUs. (See Figure 4-3)
The
cooling kit is comprised of a CPU heat sink and a cooling fan.
NOTE:
The CF-479B-RS heat sink comes with a sprayed layer of thermal paste.
Page 69
KINO-9452 Motherboard
Make sure the paste is not accidentally wiped during the unpacking or
installation of the heat sink. Thermal paste between the CPU and the heat
sink is important for optimum heat dissipation.
To install the CF-479B-RS cooling kit, please follow the steps below.
Step 1: Place the cooling kit onto the CPU. Make sure the CPU cable can be
properly routed when the cooling kit is installed.
Step 2: Properly align the cooling kit. Make sure its four spring screw fasteners can
pass through the pre-drilled holes on the PCB.
Step 3: Secure the cooling kit. From the solder side of the PCB, align the support
bracket to the screw threads on heat sink that were inserted through the PCB
holes. (See Figure 4-4)
Figure 4-4: Securing the Cooling Kit
Step 4: Tighten the screws. Use a screwdriver to tighten the four screws. Tighten each
nut a few turns at a time and do not over-tighten the screws.
Step 5: Connect the fan cable. Connect the cooling kit fan cable to the fan connector
on the motherboard. Carefully route the cable and avoid heat generating chips
and fan blades. (See Figure 4-5) Step 0:
Page 70
IEI® Technology, Corp.
KINO-9452 Motherboard
Figure 4-5: Connect the cooling fan cable
4.4.3 DIMM Module Installation
4.4.3.1 Purchasing the Memory Module
WARNING!
When purchasing the DIMM modules, make sure the modules are
compatible with the DIMM slot specified in Section 2.6 Memory
Support.
WARNING!
The board supports DDR2 DIMM modules only. DDR1 and DDR2 are
not compatible. If a DDR1 DIMM module is installed, the system may
be damaged and become inaccessible. Please only use DDR2 DIMM
modules.
4.4.3.2 DIMM Module Installation
The KINO-9452 has two 240-pin DDR2 SDRAM DIMM sockets. Follow the steps below to
install the DIMM modules.
Step 1: Make sure the two handles of the DIMM socket are in the "open" position,
leaning outward (Figure 4-6).
Page 71
KINO-9452 Motherboard
Figure 4-6: Installing the DIMM Module
Step 2: Slowly slide the DIMM module along the plastic guides on both ends of the
socket. Press the DIMM module down into the socket until it clicks into position
and the two handles have automatically locked the memory module into place
(Figure 4-7).
Figure 4-7: Locking the DIMM Module
Step 3: To remove the memory module, push both handles outward, and the memory
Page 72
IEI® Technology, Corp.
KINO-9452 Motherboard
module is ejected by the mechanism in the socket. Step 0:
4.4.4 Peripheral Device Connection
Cables provided by IEI that connect peripheral devices to the motherboard are listed in
Table 4-1. Cables not included in the kit must be separately purchased.
Quantity
Type
1
IDE flat cable
2
SATA cables
1
SATA power cable
2
RS-232 cables
1
HDTV-out cable
Table 4-1: IEI Provided Cables
4.4.4.1 IDE Disk Drive Connector (IDE1)
The cable used to connect the motherboard to the IDE device is a standard 40-pin
ATA/100 flat cable. To connect an IDE device to the motherboard, follow the instructions
below.
Step 1: Find the IDE flat cable in the kit that came with the motherboard.
Step 2: Connect one end of the cable to the IDE connector on the motherboard. A keyed
pin on the IDE connector prevents it from being connected incorrectly.
Step 3: Locate the red wire on the other side of the cable that corresponds to the pin 1
connector.
Step 4: Connect the other side of the cable to the IDE device making sure that the pin 1
cable corresponds to pin 1 on the connector.Step 0:
Page 73
KINO-9452 Motherboard
Figure 4-8: Connection of IDE Connector
NOTE:
When two IDE disk drives are connected together, back-end jumpers on
the drives must be used to configure one drive as a master and the other as
a slave.
4.4.4.2 COM Port Connectors
The KINO-9452 provides four serial ports (COM1, COM2, COM3 and COM4) interfaced
through two 10-pin male headers (COM3 and COM4), one 14-pin male headers (COM2)
and one DB-9 connector (COM1). The serial ports facilitate the connection to serial
devices or a communications network, e.g., terminal console.
Page 74
IEI® Technology, Corp.
KINO-9452 Motherboard
4.5 On-board Jumpers
NOTE:
A jumper is a metal bridge that is
used to close an electrical circuit. It
consists of two metal pins and a small
metal clip (often protected by a plastic
cover) that slides over the pins to
connect them. To CLOSE/SHORT a
jumper means connecting the pins of
the jumper with the plastic clip and to
OPEN a jumper means removing the
Figure 4-9 Jumper
plastic clip from a jumper.
The KINO-9452 motherboard has three on-board jumpers. The jumpers are described in
Table 4-2.
Description
Label
Type
Clear CMOS
JP3
3-pin header
COM2 mode selection
JP1
3-pin header
LVDS LCD voltage selection
JP2
6-pin header
Table 4-2: On-board Jumpers
Page 75
KINO-9452 Motherboard
Figure 4-10: Jumper Locations
4.5.1 Clear CMOS Jumper
Jumper Label:
JP3
Jumper Type:
3-pin header
Jumper Settings:
See Table 4-3
Jumper Location:
See Figure 4-10
If the KINO-9452 fails to boot due to improper BIOS settings, use this jumper to clear the
CMOS data and reset the system BIOS information. To do this, use the jumper cap to
close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
Page 76
IEI® Technology, Corp.
KINO-9452 Motherboard
If the “CMOS Settings Wrong” message is displayed during the boot up process, the fault
may be corrected by pressing the F1 to enter the CMOS Setup menu. Do one of the
following:
Enter the correct CMOS setting
Load Optimal Defaults
Load Failsafe Defaults.
After having done one of the above, save the changes and exit the CMOS Setup menu.
Clear CMOS
DESCRIPTION
Short 1-2
Normal Operation (Default)
Short 2-3
Clear CMOS Setup
Table 4-3: Clear CMOS Jumper Settings
The clear CMOS jumper is located in Figure 4-10.
4.5.2 COM2 Mode Selection
Jumper Label:
JP1
Jumper Type:
3-pin header
Jumper Settings:
See Table 4-4
Jumper Location:
See Figure 4-10
This jumper configures the COM2 connector as an RS-232 serial port or an
RS-422/RS-485 serial port. The selection options are shown in Table 4-4.
JP1
DESCRIPTION
Short 1-2
RS-232 (Default)
Short 2-3
RS-422/RS-485
Table 4-4: JP1 Jumper Settings
Page 77
KINO-9452 Motherboard
4.5.3 LVDS LCD Voltage Selection
WARNING:
Making the wrong setting on this jumper may cause irreparable damage to
both the motherboard and the LCD screen connected to the onboard
connector.
Jumper Label:
JP2
Jumper Type:
6-pin header
Jumper Settings:
See Table 4-5
Jumper Location:
See Figure 4-10
This jumper allows the user to set the voltage for the LCD panel. Before setting this
jumper please refer to the LCD panel user guide to determine the required voltage. After
the required voltage is known, make the necessary jumper setting in accordance with the
settings shown in Table 4-5.
JP2
DESCRIPTION
1-2
+3V
3-4
+5V
5-6
+12V
Table 4-5: JP2 Jumper Settings
4.6 Chassis Installation
After the CPU, the cooling kit, and the DIMM modules have been installed and after the
internal peripheral connectors have been connected to the peripheral devices and the
jumpers have been configure, the motherboard can be mounted into chassis.
To mount the motherboard into a chassis please refer to the chassis user guide that came
with the product.
Page 78
IEI® Technology, Corp.
KINO-9452 Motherboard
4.7 Rear Panel Connectors
4.7.1 LCD Panel Connection
The conventional CRT monitor connector is a 15-pin, female D-SUB connector. Pin
assignments can be seen in that can be connected to external monitors.
4.7.2 Ethernet Connection
The rear panel RJ-45 connectors can be connected to an external LAN and communicate
with data transfer rates up to 1Gb/s.
4.7.3 USB Connection
The rear panel USB connectors provide easier and quicker access to external USB
devices. The rear panel USB connector is a standard connector and can easily be
connected to other USB devices.
4.7.4 Serial Connection
The rear panel serial connector (COM1) provides easy and quick access to external serial
devices.
4.7.5 Keyboard and Mouse Connection
A PS/2 keyboard and a PS/2 mouse can be connected to the appropriate PS/2 connector
on the rear panel.
4.7.6 Audio Interface
Value 7.1+2 Channel High Definition Audio (HDA) signals are interfaced through the audio
jack connectors. The signals include microphone line-in, line-in stereo, Center/Subwoofer
speaker out, rear speaker out and side speaker out.
Page 79
KINO-9452 Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 80
IEI® Technology, Corp.
KINO-9452 Motherboard
Chapter
5
5 AMI BIOS Setup
Page 81
KINO-9452 Motherboard
5.1 Introduction
A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup
program allows users to modify the basic system configuration. This chapter describes
how to access the BIOS setup program and the configuration options that may be
changed.
5.1.1 Starting Setup
The AMI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DELETE key as soon as the system is turned on or
2. Press the DELETE key when the “Press Del to enter SETUP” message
appears on the screen. 0.
If the message disappears before, restart the computer and try again.
5.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the “+” and “-“ keys to
change entries, press F1 for help and press ESC to quit. Navigation keys are shown in.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
“+” key
Increase the numeric value or make changes
“-“ key
Decrease the numeric value or make changes
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
Page 82
IEI® Technology, Corp.
KINO-9452 Motherboard
F2 /F3 key
Change color from total 16 colors. F2 to select color
forward.
F10 key
Save all the CMOS changes, only for Main Menu
Table 5-1: BIOS Navigation Keys
5.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC
or the F1 key again.
5.1.4 Unable to Reboot after Configuration Changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter 4, Section 4.5.1.
5.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
Main Changes the basic system configuration.
Advanced Changes the advanced system settings.
PCIPnP Changes the advanced PCI/PnP Settings
Boot Changes the system boot configuration.
Security Sets User and Supervisor Passwords.
Chipset Changes the chipset settings.
Exit Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
5.2 Main
When the BIOS Setup program is entered, the Main menu (BIOS Menu 1) appears. The
Main menu gives an overview of the basic system information.
Page 83
KINO-9452 Motherboard
BIOS Menu 1: Main
System Overview
The System Overview lists a brief summary of different system components. The fields in
System Overview cannot be changed. The items shown in the system overview include:
AMI BIOS: Displays auto-detected BIOS information
o
o
o
Version:
Current BIOS version
Build Date: Date the current BIOS version was made
ID:
Installed BIOS ID
Processor: Displays auto-detected CPU specifications
o
o
o
Type: Names the currently installed processor
Speed: Lists the processor speed
Count: The number of CPUs on the motherboard
System Memory: Displays the auto-detected system memory.
o
Size:
Lists memory size
The System Overview field also has two user configurable fields:
Page 84
IEI® Technology, Corp.
KINO-9452 Motherboard
System Time [xx:xx:xx]: The system time is set here.
System Date [Day xx/xx/xxxx]: The system date is set here.
5.3 Advanced
The Advanced menu (BIOS Menu 2) allows access to the CPU and peripheral device
configuration options through the following sub-menus:
WARNING:
Setting the wrong values in the sections below may cause the system to
malfunction. Make sure that the settings made are compatible with the
hardware.
CPU Configuration (see Section 5.3.1)
IDE Configuration (see Section 5.3.2)
SuperIO Configuration (see Section 5.3.3)
Hardware Health Configuration (see Section 5.3.4)
ACPI Configuration (see Section 5.3.5)
APM Configuration (see Section 5.3.6)
MPS Configuration (see Section 5.3.7)
Remote Access Configuration (see Section 5.3.8)
USB Configuration (see Section 5.3.9)
Page 85
KINO-9452 Motherboard
BIOS Menu 2: Advanced
5.3.1 CPU Configuration
The CPU Configuration menu (BIOS Menu 3) shows detailed CPU specifications and
CPU configuration options.
Page 86
IEI® Technology, Corp.
KINO-9452 Motherboard
BIOS Menu 3: CPU Configuration
The CPU Configuration menu (BIOS Menu 3) lists the following CPU details:
Manufacturer: Lists the name of the CPU manufacturer
Brand String: Lists the brand name of the CPU being used
Frequency: Lists the CPU processing speed
FSB Speed: Lists the FSB speed
Cache L1: Lists the CPU L1 cache size
Cache L2: Lists the CPU L2 cache size
5.3.2 IDE Configuration
The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the
IDE devices installed in the system.
Page 87
KINO-9452 Motherboard
BIOS Menu 4: IDE Configuration
ATA/IDE Configuration [Compatible]
The ATA/IDE Configuration BIOS option allows the user to configure the ATA/IDE device
mode.
Disable all ATA/IDE ports. No Primary/Secondary IDE
Disabled
mode is presented for configuration
Compatible
DEFAULT
Up to 4 HDDs can be used, two for SATA and the other
for PATA IDE. If this option is selected, “Legacy IDE
Channels” option is presented for configuration.
Enhanced
If this option is selected, “Configure SATA as” and
“Configure SATA channels” options are presented for
configuration.
Page 88
IEI® Technology, Corp.
KINO-9452 Motherboard
Legacy IDE Channels [SATA Pri, PATA Sec]
Use the Legacy IDE Channels option configures PATA and SATA resources for operating
systems that require legacy IDE operation.
SATA Only
Enable up to two SATA devices
Reserved
The legacy IDE channels are reserved
SATA
Pri,
DEFAULT
This option allows the system to access the SATA
PATA Sec
devices before the primary IDE devices
PATA Only
Enable the two primary IDE devices. Select this option
only when the two primary IDE devices are available
IDE Master and IDE Slave
When entering setup, BIOS auto detects the presence of IDE devices. This displays the
status of the auto detected IDE devices. The following IDE devices are detected and are
shown in the IDE Configuration menu:
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the
IDE devices installed in the system. If an IDE device is detected, and one of the above
listed four BIOS configuration options are selected, the IDE configuration options shown in
Section 5.3.2.1 appear.
5.3.2.1 IDE Master, IDE Slave
IDE Master and IDE Slave configuration options for both primary and secondary IDE
devices are shown in the BIOS menu below.
Page 89
KINO-9452 Motherboard
BIOS Menu 5: IDE Master and IDE Slave Configuration
Type [Auto]
The Type BIOS option determines the type of device that the AMIBIOS attempts to boot
from after the Power-On Self-Test (POST) has completed.
Selecting this value prevents the BIOS from searching
Not Installed
for an IDE disk drive on the specified channel.
Auto
DEFAULT
This selection enables the BIOS to auto detect the
IDE disk drive type attached to the specified channel.
This setting should be used if an IDE hard disk drive is
attached to the specified channel.
CD/DVD
The CD/DVD option specifies that an IDE CD-ROM
drive is attached to the specified IDE channel. The
BIOS does not attempt to search for other types of
IDE disk drives on the specified channel.
Page 90
IEI® Technology, Corp.
KINO-9452 Motherboard
This option specifies an ATAPI Removable Media
ARMD
Device. These include, but are not limited to:
ZIP
LS-120
LBA/Large Mode [Auto]
The LBA/Large Mode BIOS option disables or auto detects LBA (Logical Block
Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the
maximum drive capacity is 137 GB.
This selection prevents the BIOS from using the LBA
Disabled
mode control on the specified channel.
Auto
DEFAULT
This option allows the BIOS to auto detect the LBA mode
control on the specified channel.
Block (Multi Sector Transfer) [Auto]
Selecting this option prevents the BIOS from using
Disabled
Multi-Sector Transfer on the specified channel. The data
to and from the device occurs one sector at a time.
Auto
DEFAULT
Selecting this value to allows the BIOS to auto detect the
device support for Multi-Sector Transfers on the specified
channel. If supported. Select this value to allow the BIOS
to auto detect the number of sectors per block for transfer
from the hard disk drive to the memory. The data transfer
to and from the device occurs multiple sectors at a time.
Page 91
KINO-9452 Motherboard
PIO Mode [Auto]
The PIO Mode option selects the IDE PIO (Programmable I/O) mode program timing
cycles between the IDE drive and the programmable IDE controller. As the PIO mode
increases, the cycle time decreases.
Auto
DEFAULT
This setting allows the BIOS to auto detect the PIO mode. Use
this value if the IDE disk drive support cannot be determined.
0
PIO mode 0 selected with a maximum transfer rate of 3.3MBps
1
PIO mode 1 selected with a maximum transfer rate of 5.2MBps
2
PIO mode 2 selected with a maximum transfer rate of 8.3MBps
3
PIO mode 3 selected with a maximum transfer rate of 11.1MBps
4
PIO mode 4 selected with a maximum transfer rate of 16.6MBps
(This setting generally works with all hard disk drives
manufactured after 1999. For other disk drives, such as IDE
CD-ROM drives, check the specifications of the drive.)
DMA Mode [Auto]
The DMA Mode BIOS selection adjusts the DMA mode options.
Auto
DEFAULT
The BIOS auto detects the DMA mode. Use this value if the
IDE disk drive support cannot be determined.
S.M.A.R.T [Auto]
Self-Monitoring Analysis and Reporting Technology (SMART) feature can help predict
impending drive failures. The S.M.A.R.T BIOS option enables or disables this function.
Auto
DEFAULT
BIOS to auto detects if the hard disk drive supports
S.M.A.R.T. Use this setting if the IDE disk drive support
cannot be determined.
Page 92
IEI® Technology, Corp.
KINO-9452 Motherboard
Select this value to prevent the BIOS from using the
Disabled
SMART feature.
Select this value to allow the BIOS to use the SMART
Enabled
feature on support hard disk drives.
32Bit Data Transfer [Enabled]
The 32Bit Data Transfer BIOS option enables or disables 32-bit data transfers.
Prevents the BIOS from using 32-bit data transfers.
Disabled
Enabled
DEFAULT
Allows BIOS to use 32-bit data transfers on support hard
disk drives.
5.3.3 Super IO Configuration
The Super IO Configuration menu (BIOS Menu 6) sets or changes the configurations for
the FDD controllers, parallel ports and serial ports.
BIOS Menu 6: Super IO Configuration
Page 93
KINO-9452 Motherboard
Serial Port1 Address [3F8/IRQ4]
The Serial Port1 Address option allows BIOS to select the Serial Port 1 base address.
No base address is assigned to Serial Port 1
Disabled
3F8/IRQ4
DEFAULT
Serial Port 1 I/O port address is 3F8 and the interrupt
address is IRQ4
Serial Port 1 I/O port address is 3E8 and the interrupt
3E8/IRQ4
address is IRQ4
Serial Port 1 I/O port address is 2E8 and the interrupt
2E8/IRQ3
address is IRQ3
Serial Port1 Mode [Normal]
Allows BIOS to select the mode for Serial Port 1
Normal
DEFAULT
Serial Port 1 mode is normal
IrDA
Serial Port 1 mode is IrDA
ASK IR
Serial Port 1 mode is ASK IR
Serial Port2 Address [2F8/IRQ3]
The Serial Port2 Address option allows BIOS to select the Serial Port 2 base address.
No base address is assigned to Serial Port 2
Disabled
2F8/IRQ3
DEFAULT
Serial Port 2 I/O port address is 3F8 and the interrupt
address is IRQ3
3E8/IRQ4
Serial Port 2 I/O port address is 3E8 and the interrupt
address is IRQ4
2E8/IRQ3
Serial Port 2 I/O port address is 2E8 and the interrupt
address is IRQ3
Page 94
IEI® Technology, Corp.
KINO-9452 Motherboard
Serial Port2 Mode [Normal]
Allows BIOS to select the mode for Serial Port 2
Normal
DEFAULT
Serial Port 2 mode is normal
IrDA
Serial Port 2 mode is IrDA
ASK IR
Serial Port 2 mode is ASK IR
Serial Port3 Address [3E8]
This option allows BIOS to select the base addresses for serial port 3
No base address is assigned to serial port 3
Disabled
3E8
DEFAULT
Serial port 3 I/O port address is 3E8
2E8
Serial port 3 I/O port address is 2E8
2F0
Serial port 3 I/O port address is 2F0
2E0
Serial port 3 I/O port address is 2E0
Serial Port3 IRQ [11]
The Serial Port3 IRQ selection sets the interrupt address for serial port 3.
Serial port 3 IRQ address is 10
10
11
DEFAULT
Serial port 3 IRQ address is 11
Serial Port4 Address [2E8]
This option allows BIOS to select the base addresses for serial port 4.
Disabled
No base address is assigned to serial port 4
3E8
Serial port 4 I/O port address is 3E8
2E8
DEFAULT
Serial port 4 I/O port address is 2E8
Page 95
KINO-9452 Motherboard
2F0
Serial port 4 I/O port address is 2F0
2E0
Serial port 4 I/O port address is 2E0
Serial Port4 IRQ [10]
The Serial Port4 IRQ selection sets the interrupt address for serial port 4.
10
11
DEFAULT
Serial port 4 IRQ address is 10
Serial port 4 IRQ address is 11
5.3.4 Hardware Health Configuration
The Hardware Health Configuration menu (BIOS Menu 7) shows the operating
temperature, fan speeds and system voltages.
BIOS Menu 7: Hardware Health Configuration
Page 96
IEI® Technology, Corp.
KINO-9452 Motherboard
CPU FAN Mode Setting: [Full On mode]
The CPU FAN Mode Setting has the following options:
Full On mode
DEFAULT
If selected, there are no additional configurable
options.
Automatic
If selected, the following options will appear with
Mode
values that can be configured:
CPU Temp. Limit of OFF
CPU Temp. Limit of Start
CPU Temp. Limit of Full
CPU Fan Start PWM
Slop PWM 1: 0 PWM, 1 PWM (Default), 2
PWM, 4 PWM, 8 PWM, 16 PWM, 32 PWM
or 64 PWM
PWM Manually
If selected, the following option will appear with
mode
values that can be configured:
CPU Fan PWM Control
The following system parameters and values are shown. The system parameters that are
monitored are:
System Temperatures: The following system temperatures are monitored
o
o
CPU Temperature
System Temperature
Fan Speeds: The CPU cooling fan speed is monitored.
o
o
CPU Fan Speed
System Fan Speed
Voltages: The following system voltages are monitored
o
o
CPU Core
+2.5V
Page 97
KINO-9452 Motherboard
o
o
o
o
o
o
o
+3.30V
+5.00V
+12.0V
GMCH (1.5V)
1.05V
5VSB
VBAT
5.3.5 ACPI Configuration
The ACPI Configuration menu (BIOS Menu 8) configures the Advanced Configuration
and Power Interface (ACPI) and Power Management (APM) options.
BIOS Menu 8: ACPI Configuration
ACPI Aware O/S [Yes]
Use the ACPI Aware O/S option to enable the system to configure ACPI power saving
options. ACPI can only be implemented if the system OS complies with the ACPI standard.
Windows 98, Windows 2000, and Windows XP all comply with ACPI.
Page 98
IEI® Technology, Corp.
KINO-9452 Motherboard
Disables the ACPI support for the OS. This selection should
No
be disabled if the OS does not support ACPI
Yes
DEFAULT
Enables the ACPI support for the operating system. This
selection should be enabled if the OS does support ACPI
5.3.5.1 General ACPI Configuration
Use the General ACPI Configuration menu (BIOS Menu 9) to select the ACPI state
when the system is suspended.
BIOS Menu 9: General ACPI Configuration [Advanced\ ACPI Configuration]
Suspend mode [S3 (STR)]
Use the Suspend Mode option to specify the sleep state the system enters when it is not
being used.
S1 (POS)
The system enters S1(POS) sleep state. The system
Page 99
KINO-9452 Motherboard
appears off. The CPU is stopped; RAM is refreshed; the
system is running in a low power mode.
S3 (STR)
DEFAULT
The system enters a S3(STR) sleep state. The CPU has
no power; RAM is in slow refresh; the power supply is in a
reduced power mode.
5.3.6 APM Configuration
Use the APM Configuration menu (BIOS Menu 10) to select the advanced power
management.
BIOS Menu 10: APM Configuration
Power Management/APM [Enabled]
The Power Management/APM BIOS option accesses the advanced power management
features.
Disabled
Page 100
Disables the Advanced Power Management (APM)
IEI® Technology, Corp.
KINO-9452 Motherboard
feature
Enabled
DEFAULT
Enables the APM feature
Restore on AC Power Loss by IO [Power Off]
The Restore on AC Power Loss by IO BIOS option specifies what state the system
returns to if there is a sudden loss of power to the system.
Power Off
DEFAULT
The system remains turned off
The system turns on
Power On
Power Button Mode [On/Off]
The Power Button Mode BIOS specifies how the power button functions.
On/Off
DEFAULT
When the power button is pressed the system is either
turned on or off
Resume on Ring [Disabled]
The Resume on Ring BIOS option specifies if the system will be roused from a
suspended or standby state when there is activity on the RI (ring in) modem line. That is,
the system will be roused by an incoming call on a modem.
Disabled
DEFAULT
Wake event not generated by an incoming call
Wake event generated by an incoming call
Enabled
Resume on PME# [Disabled]
The Resume on PME# BIOS option specifies if the system will be roused from a
suspended or standby state when there is activity on the PCI PME (power management
event) controller.
Disabled
DEFAULT
Wake event not generated by PCI PME controller
Page 101
KINO-9452 Motherboard
activity
Wake event generated by PCI PME controller activity
Enabled
Resume On RTC Alarm [Disabled]
The Resume On RTC Alarm determines when the computer will be roused from a
suspended state.
Disabled
DEFAULT
The real time clock (RTC) cannot generate a wake
event
If selected, the following will appear with values that
Enabled
can be selected:
RTC Alarm Date (Days)
RTC Alarm Time
After setting the alarm, the computer will turn itself on
from a suspend state when the alarm goes off.
Resume On PCI-Express WAKE# [Enabled]
The Resume On PCI-Express WAKE# BIOS option specifies if the system will be roused
from a suspended or standby state when there is activity on the PCI-Express controller.
Wake event not generated by PCI-Express controller
Disabled
activity
Enabled
DEFAULT
Wake event generated by PCI-Express controller
activity
5.3.7 MPS Configuration
Use the MPS Configuration menu (BIOS Menu 11) to select `he multi-processor table.
Page 102
IEI® Technology, Corp.
KINO-9452 Motherboard
BIOS Menu 11: MPS Configuration
MPS Revision [1.4]
Use the Multiprocessor Specification (MPS) Revision option to specify the MPS
version to be used.
MPS version 1.1 is used
1.1
1.4
DEFAULT
MPS version 1.4 is used
5.3.8 Remote Access Configuration
Use the Remote Access Configuration menu (BIOS Menu 12) to configure remote
access parameters. The Remote Access Configuration is an AMIBIOS feature and
allows a remote host running a terminal program to display and configure the BIOS
settings.
Page 103
KINO-9452 Motherboard
BIOS Menu 12: Remote Access Configuration [Advanced]
Remote Access [Disabled]
Use the Remote Access option to enable or disable access to the remote functionalities
of the system.
Disabled
Enabled
DEFAULT
Remote access is disabled.
Remote access configuration options shown below
appear:
Serial Port Number
Serial Port Mode
Flow Control
Redirection after BIOS POST
Page 104
IEI® Technology, Corp.
KINO-9452 Motherboard
Terminal Type
VT-UTF8 Combo Key Support
Sredir Memory Display Delay
These configuration options are discussed below.
5.3.9 USB Configuration
Use the USB Configuration menu (BIOS Menu 13) to read USB configuration
information and configure the USB settings.
BIOS Menu 13: USB Configuration
USB Configuration
The USB Configuration field shows the system USB configuration. The items listed are:
Page 105
KINO-9452 Motherboard
Module Version: x.xxxxx.xxxxx
USB Devices Enabled
The USB Devices Enabled field lists the USB devices that are enabled on the system
USB Function [8 USB Ports]
Use the USB Function BIOS option to disable USB function support or to set the number
of USB ports to activate.
Disabled
USB function support disabled
2 USB Ports
Two USB ports are activated.
4 USB Ports
Four USB ports are activated.
6 USB Ports
Six USB ports are activated.
8 USB Ports
DEFAULT
Eight USB ports are activated.
USB 2.0 Controller [Enabled]
Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller
Enabled
DEFAULT
Disabled
USB 2.0 controller enabled
USB 2.0 controller disabled
Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support.
Normally if this option is not enabled, any attached USB mouse or USB keyboard does not
become available until a USB compatible operating system is fully booted with all USB
drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard
can control the system even when there is no USB driver loaded onto the system.
Page 106
IEI® Technology, Corp.
KINO-9452 Motherboard
Legacy USB support disabled
Disabled
Enabled
DEFAULT
Legacy USB support enabled
Legacy USB support disabled if no USB devices are
Auto
connected
USB2.0 Controller Mode [HiSpeed]
Use the USB2.0 Controller Mode option to set the speed of the USB2.0 controller.
The controller is capable of operating at 12Mb/s
FullSpeed
HiSpeed
DEFAULT
The controller is capable of operating at 480Mb/s
BIOS EHCI Handoff [Enabled]
Use the BIOS EHCI Handoff option for systems running OSes that do not have EHCI
hand-off support. The EHCI ownership change is managed by the EHCI driver.
Systems with OSes that do not support EHCI can
Disabled
use the EHCI handoff functionality.
Enabled
DEFAULT
Systems with OSes that do not support EHCI cannot
use the EHCI handoff functionality.
5.3.9.1 USB Mass Storage Device Configuration
Use the USB Mass Storage Device Configuration menu (BIOS Menu 14) to configure
USB mass storage class devices.
Page 107
KINO-9452 Motherboard
BIOS Menu 14: USB Mass Storage Device Configuration
Device ##
The Device## field lists the USB devices that are connected to the system.
Emulation Type [Auto]
Use the Emulation Type BIOS option to specify the type of emulation BIOS has to
provide for the USB device.
NOTE:
Please note that the device’s formatted type and the emulation type
provided by the BIOS must match for a device to boot properly. If both
types do not match then device’s behavior is undefined. To make sure both
types match, format the device using BIOS INT13h calls after selecting the
Page 108
IEI® Technology, Corp.
KINO-9452 Motherboard
proper emulation option in BIOS setup. The FORMAT utility provided by
Microsoft® MS-DOS®, Microsoft® Windows® 95, and Microsoft®
Windows® 98 can be used for this purpose.
Auto
Floppy
DEFAULT
BIOS auto-detects the current USB.
The USB device will be emulated as a floppy drive.
The device can be either A: or B: responding to
INT13h calls that return DL = 0 or DL = 1
respectively.
Forced FDD
Allows a hard disk image to be connected as a
floppy image. This option works only for drives
formatted with FAT12, FAT16 or FAT32.
Hard Disk
Allows the USB device to be emulated as hard disk
responding to INT13h calls that return DL values of
80h or above.
CDROM
Assumes the CD-ROM is formatted as bootable
media. All the devices that support block sizes
greater than 512 bytes can only be booted using this
option.
5.4 PCI/PnP
Use the PCI/PnP menu (BIOS Menu 15) to configure advanced PCI and PnP settings.
WARNING!
Setting wrong values for the BIOS selections in the PCIPnP BIOS menu
may cause the system to malfunction.
Page 109
KINO-9452 Motherboard
BIOS Menu 15: PCI/PnP Configuration
Clear NVRAM [No]
Use the Clear NVRAM option to specify if the NVRAM (Non-Volatile RAM) is cleared
when the power is turned off.
No
DEFAULT
System does not clear NVRAM during system boot
System clears NVRAM during system boot
Yes
Plug & Play O/S [No]
Use the Plug & Play O/S BIOS option to specify whether system plug and play devices
are configured by the operating system or the BIOS.
No
Page 110
DEFAULT
If the operating system does not meet the Plug and Play
IEI® Technology, Corp.
KINO-9452 Motherboard
specifications, this option allows the BIOS to configure all the
devices in the system.
This setting allows the operating system to change the
Yes
interrupt, I/O, and DMA settings. Set this option if the system
is running Plug and Play aware operating systems.
PCI Latency Timer [64]
Use the PCI Latency Timer option to specify the PCI latency time. The latency time is
measured in units of PCI clock cycles for the PCI device latency timer register.
Configuration options are:
32
64
DEFAULT
96
128
160
192
224
248
Allocate IRQ to PCI VGA [Yes]
Use the Allocate IRQ to PCI VGA option to restrict the system from giving the VGA
adapter card an interrupt address.
Yes
DEFAULT
No
Assigns an IRQ to a PCI VGA card if card requests IRQ
Does not assign IRQ to a PCI VGA card even if the card
requests an IRQ
Palette Snooping [Disabled]
Use the Palette Snooping option to enable or disable the palette snooping function.
Disabled
DEFAULT
Unless the VGA card manufacturer requires palette
Page 111
KINO-9452 Motherboard
snooping to be enabled, this option should be disabled.
PCI devices are informed that an ISA based Graphics
Enabled
device is installed in the system so the ISA based
Graphics card functions correctly. This does not
necessarily indicate a physical ISA adapter card. The
graphics chipset can be mounted on a PCI card. Always
check with the adapter card manual first, before
modifying the default settings in the BIOS.
PCI IDE BusMaster [Enabled]
Use the PCI IDE BusMaster BIOS option to enable or prevent PCI IDE busmastering.
Busmastering is prevented
Disabled
Enabled
DEFAULT
IDE controller on the PCI local bus has mastering
capabilities
OffBoard PCI/ISA IDE Card [Auto]
Use the OffBoard PCI/ISA IDE Card BIOS option to select the OffBoard PCI/ISA IDE
Card.
Auto
DEFAULT
The location of the Off Board PCI IDE adapter card is
automatically detected by the AMIBIOS.
PCI Slot 1
PCI Slot 1 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 1.
PCI Slot 2
PCI Slot 2 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 2.
PCI Slot 3
Page 112
PCI Slot 3 is selected as the location of the OffBoard
IEI® Technology, Corp.
KINO-9452 Motherboard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 3.
PCI Slot 4 is selected as the location of the OffBoard
PCI Slot 4
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 4.
PCI Slot 5 is selected as the location of the OffBoard
PCI Slot 5
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 5.
PCI Slot 6 is selected as the location of the OffBoard
PCI Slot 6
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 6.
IRQ# [Available]
Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral
device.
Available
DEFAULT
The specified IRQ is available to be used by
PCI/PnP devices
Reserved
The specified IRQ is reserved for use by Legacy ISA
devices
Available IRQ addresses are:
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ 11
IRQ 14
Page 113
KINO-9452 Motherboard
IRQ 15
DMA Channel# [Available]
Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP
device.
Available
DEFAULT
The specified DMA is available to be used by
PCI/PnP devices
The specified DMA is reserved for use by Legacy
Reserved
ISA devices
Available DMA Channels are:
DM Channel 0
DM Channel 1
DM Channel 3
DM Channel 5
DM Channel 6
DM Channel 7
Reserved Memory Size [Disabled]
Use the Reserved Memory Size BIOS option to specify the amount of memory that
should be reserved for legacy ISA devices.
Disabled
Page 114
DEFAULT
No memory block reserved for legacy ISA devices
16K
16KB reserved for legacy ISA devices
32K
32KB reserved for legacy ISA devices
64K
54KB reserved for legacy ISA devices
IEI® Technology, Corp.
KINO-9452 Motherboard
5.5 Boot
Use the Boot menu (BIOS Menu 16) to configure system boot options.
BIOS Menu 16: Boot
5.5.1 Boot Settings Configuration
Use the Boot Settings Configuration menu (BIOS Menu 17) to configure advanced
system boot options.
Page 115
KINO-9452 Motherboard
BIOS Menu 17: Boot Settings Configuration
Quick Boot [Enabled]
Use the Quick Boot BIOS option to make the computer speed up the boot process.
No POST procedures are skipped
Disabled
Enabled
DEFAULT
Some POST procedures are skipped to decrease
the system boot time
Quiet Boot [Disabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
Disabled
Enabled
Page 116
DEFAULT
Normal POST messages displayed
OEM Logo displayed instead of POST messages
IEI® Technology, Corp.
KINO-9452 Motherboard
AddOn ROM Display Mode [Force BIOS]
Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory)
messages to be displayed.
Force BIOS
DEFAULT
The system forces third party BIOS to display
during system boot.
The system displays normal information during
Keep Current
system boot.
Bootup Num-Lock [On]
Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be
modified during boot up.
Does not enable the keyboard Number Lock automatically. To
Off
use the 10-keys on the keyboard, press the Number Lock key
located on the upper left-hand corner of the 10-key pad. The
Number Lock LED on the keyboard lights up when the Number
Lock is engaged.
On
DEFAULT
Allows the Number Lock on the keyboard to be enabled
automatically when the computer system boots up. This allows
the immediate use of the 10-key numeric keypad located on
the right side of the keyboard. To confirm this, the Number
Lock LED light on the keyboard is lit.
PS/2 Mouse Support [Auto]
Use the PS/2 Mouse Support option adjusts PS/2 mouse support capabilities.
Disabled
PS/2 mouse support is disabled and prevented from
using system resources.
Enabled
Allows the system to use a PS/2 mouse.
Page 117
KINO-9452 Motherboard
Auto
DEFAULT
The system auto-adjusts PS/2 mouse support.
Boot From LAN Support [Disabled]
The BOOT From LAN Support option enables the system to be booted from a remote
system.
Disabled
DEFAULT
Cannot be booted from a remote system through the
LAN
Enabled
Can be booted from a remote system through the
LAN
5.5.2 Boot Device Priority
Use the Boot Device Priority menu (BIOS Menu 18) to specify the boot sequence from
the available devices. Possible boot devices may include:
1st FLOPPY DRIVE
HDD
CD/DVD
Page 118
IEI® Technology, Corp.
KINO-9452 Motherboard
BIOS Menu 18: Boot Device Priority Settings
5.5.3 Removable Drives
Use the Removable Drives menu (BIOS Menu 19) to specify the boot sequence of the
available FDDs. When the menu is opened, the FDDs connected to the system are listed
as shown below:
1st Drive
NOTE:
Only the drives connected to the system are shown. For example, if only
one FDD is connected only “1st Drive” is listed.
Page 119
KINO-9452 Motherboard
The boot sequence from the available devices is selected. If the “1st Drive” option is
selected a list of available removable drives is shown. Select the first drive the system
boots from. If the “1st Drive” is not used for booting this option may be disabled.
BIOS Menu 19: Removable Drives
5.6 Security
Use the Security menu (BIOS Menu 20) to set system and user passwords.
Page 120
IEI® Technology, Corp.
KINO-9452 Motherboard
BIOS Menu 20: Security
Change Supervisor Password
Use the Change Supervisor Password to set or change a supervisor password. The
default for this option is Not Installed. If a supervisor password must be installed, select
this field and enter the password. After the password has been added, Install appears
next to Change Supervisor Password.
Change User Password
Use the Change User Password to set or change a user password. The default for this
option is Not Installed. If a user password must be installed, select this field and enter the
password. After the password has been added, Install appears next to Change User
Password.
Page 121
KINO-9452 Motherboard
5.7 Chipset
Use the Chipset menu (BIOS Menu 21) to access the NorthBridge and SouthBridge
configuration menus
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
BIOS Menu 21: Chipset
5.7.1 North Bridge Configuration
Use the North Bridge Configuration menu (BIOS Menu 22) to configure the northbridge
chipset.
Page 122
IEI® Technology, Corp.
KINO-9452 Motherboard
BIOS Menu 22: North Bridge Chipset Configuration
DRAM Frequency [Auto]
Use the DRAM Frequency option to specify the DRAM frequency or allow the system to
automatically detect the DRAM frequency.
Auto
DEFAULT
Automatically selects the DRAM frequency
400MHz
Sets the DRAM frequency to 400MHz
533MHz
Sets the DRAM frequency to 533MHz
667MHz
Sets the DRAM frequency to 667MHz
Configure DRAM Timing by SPD [Enabled]
Use the Configure DRAM Timing by SPD option to determine if the system uses the
SPD (Serial Presence Detect) EEPROM to configure the DRAM timing. The SPD
EEPROM contains all necessary DIMM specifications including the speed of the individual
Page 123
KINO-9452 Motherboard
components such as CAS and bank cycle time as well as valid settings for the module and
the manufacturer's code. The SPD enables the BIOS to read the spec sheet of the DIMMs
on boot-up and then adjust the memory timing parameters accordingly.
DRAM timing parameters are manually set using the
Disabled
DRAM sub-items
Enabled
DEFAULT
DRAM timing parameter are set according to the
DRAM Serial Presence Detect (SPD)
If the Configure DRAM Timing by SPD option is disabled, the following configuration
options appear.
DRAM CAS# Latency [3]
DRAM RAS# to CAS# Delay [5 DRAM Clocks]
DRAM RAS# Precharge [5 DRAM Clocks]
DRAM RAS# Activate to Precha [15 DRAM Clocks]
Memory Hole [Disabled]
Use the Memory Hole option to reserve memory space between 15MB and 16MB for ISA
expansion cards that require a specified area of memory to work properly. If an older ISA
expansion card is used, please refer to the documentation that came with the card to see
if it is necessary to reserve the space.
Disabled
15MB – 16MB
DEFAULT
Memory is not reserved for ISA expansion cards
Between 15MB and 16MB of memory is reserved for
ISA expansion cards
Boots Graphics Adapter Priority [PEG/PCI]
Use the Boots Graphics Adapter Priority option to select the graphics controller used as
the primary boot device. Select either an integrated graphics controller (IGD) or a
combination of PCI graphics controller, a PCI express (PEG) controller or an IGD.
Configuration options are listed below:
Page 124
IEI® Technology, Corp.
KINO-9452 Motherboard
IGD
PCI/IGD
PCI/PEG
PEG/IGD
PEG/PCI
DEFAULT
Internal Graphics Mode Select [Enable, 8MB]
Use the Internal Graphic Mode Select option to specify the amount of system memory
that can be used by the Internal graphics device.
Disable
1MB of memory used by internal graphics device
Enable, 1MB
Enable, 8MB
DEFAULT
8MB of memory used by internal graphics device
PEG Port [Auto]
Use the PEG Port option to enable or disable the PCI Express port.
Auto
DEFAULT
BIOS auto detects the installed PEG cards
Installed PEG cards cannot function
Disabled
PEG Force X1 [Disabled]
Use the PEG Force x1 option to convert a PCI express X16 slot into a PCI express X1
slot.
PCI express X16 slot runs in PCI express X1
Enabled
mode
Disabled
DEFAULT
PCI express X16 slot runs in normal mode
5.7.1.1 Video Function Configuration
Use the Video Function Configuration menu to configure the video device connected to
the system.
Page 125
KINO-9452 Motherboard
DVMT Mode Select [DVMT Mode]
Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology
(DVMT) operating mode.
A fixed portion of graphics memory is reserved as
Fixed Mode
graphics memory.
DVMT Mode
Graphics
DEFAULT
memory
is
dynamically
allocated
according to the system and graphics needs.
A fixed portion of graphics memory is reserved as
Combo Mode
graphics memory. If more memory is needed,
graphics
memory
is
dynamically
allocated
according to the system and graphics needs.
DVMT/FIXED Memory [128MB]
Use the DVMT/FIXED Memory option to specify the maximum amount of memory that
can be allocated as graphics memory. This option can only be configured for if DVMT
Mode or Fixed Mode is selected in the DVMT Mode Select option. If Combo Mode is
selected, the maximum amount of graphics memory is 128MB. Configuration options are
listed below.
64MB
128MB
DEFAULT
Maximum DVMT
Boot Display Device [Auto]
Use the Boot Display Device option to select the display device used by the system
when it boots. Configuration option is listed below.
Auto
Page 126
DEFAULT
IEI® Technology, Corp.
KINO-9452 Motherboard
Flat Panel Type [640*480]
Use the Flat Panel Type option to select the type of flat panel connected to the system.
Configuration options are listed below.
640*480
DEFAULT
800*600
1024*768
1280*1024 (36bits)
1400*1050 (36bits)
1600*1200 (36bits)
1280*768
1680*1050 (36bits)
1920*1200 (36bits)
Local Flat Panel Scaling [Auto]
Use the Local Flat Panel Scaling option to select the method of scaling for the flat panel
screen attached to the system.
Auto
DEFAULT
Scaling is automatic
Forced Scaling
Scaling is forced
Disabled
Scaling is disabled
TV Connector [Auto]
Use the TC Connector option to select the connector that is used to connect the system
to the television. The configuration option is listed below.
Auto
DEFAULT
TV Standard [VBIOS-Default]
Use the TV Standard option to select the standard of the television connected to the
system. The configuration options are listed below.
VBIOS-Default
DEFAULT
Page 127
KINO-9452 Motherboard
NTSC
PAL
5.7.2 South Bridge Configuration
The SouthBridge Configuration menu (BIOS Menu 23) the southbridge chipset to be
configured.
BIOS Menu 23:South Bridge Chipset Configuration
Audio Controller [Azalia]
The Audio Controller option enables or disables the High Definition Audio CODEC.
Azalia
DEFAULT
The Intel High Definition Audio controller automatically
detected and enabled
Disabled
Page 128
The onboard High Definition Audio controller is disabled
IEI® Technology, Corp.
KINO-9452 Motherboard
OnBoard LAN1 (BCM5787M) [Enabled]
The OnBoard LAN1 (BCM5787M) option enables or disables the onboard LAN1.
Onboard LAN1 controller manually disabled
Disabled
Enabled
DEFAULT
The onboard LAN1 controller automatically detected and
enabled
OnBoard LAN2 (BCM5787M) [Enabled]
The OnBoard LAN2 (BCM5787M) option enables or disables the onboard LAN1.
Onboard LAN2 controller manually disabled
Disabled
Enabled
DEFAULT
The onboard LAN2 controller automatically detected and
enabled
5.8 Exit
Use the Exit menu (BIOS Menu 24) to load default BIOS values, optimal failsafe values
and to save configuration changes.
BIOS Menu 24:Exit
Page 129
KINO-9452 Motherboard
Save Changes and Exit
Use the Save Changes and Exit option to save the changes made to the BIOS options
and to exit the BIOS configuration setup program.
Discard Changes and Exit
Use the Discard Changes and Exit option to exit the BIOS configuration setup program
without saving the changes made to the system.
Discard Changes
Use the Discard Changes option to discard the changes and remain in the BIOS
configuration setup program.
Load Optimal Defaults
Use the Load Optimal Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F9 key can be used for this operation.
Load Failsafe Defaults
Use the Load Failsafe Defaults option to load failsafe default values for each of the
parameters on the Setup menus. F8 key can be used for this operation.
Page 130
IEI® Technology, Corp.
KINO-9452 Motherboard
Chapter
6
6 Software Drivers
Page 131
KINO-9452 Motherboard
6.1 Available Software Drivers
NOTE:
The content of the CD may vary throughout the life cycle of the product and
is subject to change without prior notice. Visit the IEI website or contact
technical support for the latest updates.
The KINO-9452 motherboard has the following software drivers:
Intel Chipset Driver Installation
VGA Utilities Driver
LAN Driver (for GbE LAN) Installation
RealTek Audio Driver (ALC883) Installation
SATA Driver Installation
All drivers can be found on the CD that came with the motherboard. To install the drivers
please follow the instructions in the sections below.
6.2 Chipset Driver Installation
To install the chipset driver, please follow the steps below:
Step 1: Insert the CD into the system that contains the KINO-9452 board. Open the
1-INF directory and locate the icon for the infinst_autol.exe installation file.
Once located, use the mouse to double click the icon.
Step 2: The “InstallShield Wizard Preparation Screen” in Figure 6-1 appears.
Page 132
IEI® Technology, Corp.
KINO-9452 Motherboard
Figure 6-1: InstallShield Wizard Preparation Screen
Step 3: The “Welcome” window in Figure 6-2 appears next.
Figure 6-2: Welcome Screen
Step 4: Click “NEXT” and the license agreement shown in Figure 6-3 appears.
Page 133
KINO-9452 Motherboard
Figure 6-3: License Agreement
Step 5: Agree to the license terms by clicking “YES”. The “Readme” in Figure 6-4
appears.
Figure 6-4: Readme Information
Step 6: Click “YES”. The driver is installed on the computer. After the installation is
complete, the installation complete screen shown in Figure 6-5 appears. Select
the preferred option and click “FINISH” to complete the installation process.
Page 134
IEI® Technology, Corp.
KINO-9452 Motherboard
Step 0:
Figure 6-5: Restart the Computer
6.3 VGA Driver
To install the VGA driver, please follow the steps below:
Step 1: Insert the Utility CD that came with the motherboard into the system CD drive.
Step 2: Open the X:\2-VGA\WIN2K_XP directory (where X:\ is the system CD drive)
and double-click the win2k_xp1420.exe installation file.
Step 3: The Starting Install Shield Wizard appears (Figure 6-6).
Page 135
KINO-9452 Motherboard
Figure 6-6: Starting Install Shield Wizard Screen
Step 4: The Preparing Setup window appears next (Figure 6-7).
Figure 6-7: Preparing Setup Screen
Step 5: A Welcome screen shown in Figure 6-8 appears. Click NEXT to continue the
Page 136
IEI® Technology, Corp.
KINO-9452 Motherboard
installation.
Figure 6-8: VGA Driver Installation Welcome Screen
Step 6: A license agreement shown in Figure 6-9 appears. Read through the license
agreement.
Figure 6-9: VGA Driver License Agreement
Step 7: Accept the terms and conditions stipulated in the license agreement by clicking
Page 137
KINO-9452 Motherboard
the “YES” button (Figure 6-9). The installation notice shown in Figure 6-10
appears.
Figure 6-10: VGA Driver Installing Notice
Step 8: After the driver installation process is complete, a confirmation screen shown in
Figure 6-11 appears.
Figure 6-11: VGA Driver Installation Complete
Step 9: The confirmation screen shown in Figure 6-11 allows user to restart the
computer immediately after the installation is complete or to restart the computer
later. For the settings to take effect the computer must be restarted. Once
decided when to restart the computer, click the “FINISH” button. Step 0:
Page 138
IEI® Technology, Corp.
KINO-9452 Motherboard
6.4 Broadcom LAN Driver (for GbE LAN) Installation
To install the Broadcom LAN driver, please follow the steps below.
Step 1: Open Windows Control Panel (Figure 6-12).
Figure 6-12: Access Windows Control Panel
Step 2: Double click the System icon (Figure 6-13).
Page 139
KINO-9452 Motherboard
Figure 6-13: Double Click the System Icon
Step 3: Double click the Device Manager tab (Figure 6-14).
Figure 6-14: Double Click the Device Manager Tab
Step 4: A list of system hardware devices appears (Figure 6-15).
Page 140
IEI® Technology, Corp.
KINO-9452 Motherboard
Figure 6-15: Device Manager List
Step 5: Double click the listed device that has question marks next to it. (This means
Windows does not recognize the device).
Step 6: The Device Driver Wizard appears (Figure 6-16). Click NEXT to continue.
Figure 6-16: Search for Suitable Driver
Page 141
KINO-9452 Motherboard
Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 6-17).
Click NEXT to continue.
Figure 6-17: Locate Driver Files
Step 8: Select the proper OS folder under the “X:\3-LAN\BROADCOM BCM57xx
Drivers” directory (Figure 6-18) in the location browsing window, where “X:\” is
the system CD drive.
Figure 6-18: Location Browsing Window
Page 142
IEI® Technology, Corp.
KINO-9452 Motherboard
Step 9: Click OK to continue. A driver files location menu window appears. Click NEXT to
continue. The driver is installed.Step 0:
6.5 RealTek HD Audio Driver (ALC883) Installation
To install the Realtek High Definition (HD) Audio driver, please follow the steps below.
Step 1: Open Windows Control Panel (Figure 6-12).
Figure 6-19: Access Windows Control Panel
Step 2: Double click the System icon (Figure 6-13).
Page 143
KINO-9452 Motherboard
Figure 6-20: Double Click the System Icon
Step 3: Double click the Device Manager tab (Figure 6-14).
Figure 6-21: Double Click the Device Manager Tab
Step 4: A list of system hardware devices appears (Figure 6-15).
Page 144
IEI® Technology, Corp.
KINO-9452 Motherboard
Figure 6-22: Device Manager List
Step 5: Double click the listed device that has question marks next to it. (This means
Windows does not recognize the device).
Step 6: The Device Driver Wizard appears (Figure 6-16). Click NEXT to continue.
Page 145
KINO-9452 Motherboard
Figure 6-23: Search for Suitable Driver
Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 6-17).
Click NEXT to continue.
Page 146
IEI® Technology, Corp.
KINO-9452 Motherboard
Figure 6-24: Locate Driver Files
Step 8: Select “X:\4-AUDIO\AC-KIT883HD\WIN” directory in the location browsing
window, where “X:\” is the system CD drive (Figure 6-18).
Step 9: Click OK to continue. The driver is installed. Step 0:
Step 1: The confirmation screen offers the option of restarting the computer now or later.
For the settings to take effect, the computer must be restarted. Click FINISH to
restart the computer.Step 0:
6.6 Intel Matrix Storage Manager Installation
To install the Intel Matrix Storage Manager driver, please follow the steps below:
Step 1: Insert the Utility CD that came with the motherboard into the system CD drive.
Step 2: Open the X:\5-SATA\ICH7R directory and double-click the iata60_cd.exe
installation file.
Page 147
KINO-9452 Motherboard
Step 3: The Preparing Setup window appears ().
Figure 6-25: Preparing Setup Screen
Step 4: A Welcome screen appears. Click NEXT to continue the installation.
Step 5: A license agreement appears. Read through the license agreement.
Step 6: The “Uninstallation Warning” window appears. Click on the NEXT button to
continue.
Step 7: Accept the terms and conditions stipulated in the license agreement by clicking
the “YES” button.
Step 8: The “Choose Destination Location” window appears. Click on the NEXT button to
continue. By default, all installed files are copied to the following path:
<bootdrive>:\Program Files\Intel\Intel(R) Matrix Storage Manager.
Step 9: The “Select Program Folder” window appears. Click on the NEXT button to
continue installing the driver.
Step 10: After the driver installation process is complete, a confirmation screen appears.
Page 148
IEI® Technology, Corp.
KINO-9452 Motherboard
Step 11: The confirmation screen allows user to restart the computer immediately after
the installation is complete or to restart the computer later. For the settings to
take effect the computer must be restarted. Once decided when to restart the
computer, click the “FINISH” button. Step 0:
Page 149
KINO-9452 Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 150
IEI® Technology, Corp.
KINO-9452 Motherboard
Appendix
A
A BIOS Configuration
Options
Page 151
KINO-9452 Motherboard
A.1 BIOS Configuration Options
Below is a list of BIOS configuration options described in Chapter 5.
System Overview ...................................................................................................84
ATA/IDE Configuration [Compatible]...................................................................88
Legacy IDE Channels [SATA Pri, PATA Sec]......................................................89
IDE Master and IDE Slave .....................................................................................89
LBA/Large Mode [Auto].........................................................................................91
Block (Multi Sector Transfer) [Auto] ....................................................................91
DMA Mode [Auto]...................................................................................................92
32Bit Data Transfer [Enabled] ..............................................................................93
Serial Port1 Address [3F8/IRQ4] ..........................................................................94
Serial Port1 Mode [Normal]...................................................................................94
Serial Port2 Address [2F8/IRQ3] ..........................................................................94
Serial Port2 Mode [Normal]...................................................................................95
Serial Port3 Address [3E8]....................................................................................95
Serial Port3 IRQ [11] ..............................................................................................95
Serial Port4 Address [2E8]....................................................................................95
Serial Port4 IRQ [10] ..............................................................................................96
CPU FAN Mode Setting: [Full On mode] .............................................................97
CPU Temp. Limit of OFF .......................................................................................97
CPU Temp. Limit of Start ......................................................................................97
CPU Temp. Limit of Full ........................................................................................97
CPU Fan Start PWM ...............................................................................................97
CPU Fan PWM Control ..........................................................................................97
ACPI Aware O/S [Yes] ...........................................................................................98
Suspend mode [S3 (STR)].....................................................................................99
Power Management/APM [Enabled].................................................................. 100
Restore on AC Power Loss by IO [Power Off] ................................................. 101
Power Button Mode [On/Off] ............................................................................. 101
Resume on Ring [Disabled] ............................................................................... 101
Resume on PME# [Disabled] ............................................................................. 101
Page 152
IEI® Technology, Corp.
KINO-9452 Motherboard
Resume On RTC Alarm [Disabled].................................................................... 102
RTC Alarm Date (Days) ...................................................................................... 102
Resume On PCI-Express WAKE# [Enabled] .................................................... 102
MPS Revision [1.4].............................................................................................. 103
Remote Access [Disabled]................................................................................. 104
Serial Port Number ............................................................................................. 104
Redirection after BIOS POST............................................................................. 104
VT-UTF8 Combo Key Support ........................................................................... 105
Sredir Memory Display Delay ............................................................................ 105
USB Configuration.............................................................................................. 105
USB Devices Enabled......................................................................................... 106
USB Function [8 USB Ports].............................................................................. 106
USB 2.0 Controller [Enabled]............................................................................. 106
Legacy USB Support [Enabled]......................................................................... 106
USB2.0 Controller Mode [HiSpeed]................................................................... 107
BIOS EHCI Handoff [Enabled] ........................................................................... 107
Emulation Type [Auto] ....................................................................................... 108
Clear NVRAM [No]............................................................................................... 110
Plug & Play O/S [No]........................................................................................... 110
PCI Latency Timer [64] ....................................................................................... 111
Allocate IRQ to PCI VGA [Yes] .......................................................................... 111
Palette Snooping [Disabled] .............................................................................. 111
PCI IDE BusMaster [Enabled] ............................................................................ 112
OffBoard PCI/ISA IDE Card [Auto] .................................................................... 112
IRQ# [Available]................................................................................................ 113
DMA Channel# [Available] ................................................................................. 114
Reserved Memory Size [Disabled] .................................................................... 114
Quick Boot [Enabled] ......................................................................................... 116
Quiet Boot [Disabled] ......................................................................................... 116
AddOn ROM Display Mode [Force BIOS] ......................................................... 117
Bootup Num-Lock [On] ...................................................................................... 117
PS/2 Mouse Support [Auto] ............................................................................... 117
Page 153
KINO-9452 Motherboard
Boot From LAN Support [Disabled] .................................................................. 118
Change Supervisor Password........................................................................... 121
Change User Password...................................................................................... 121
DRAM Frequency [Auto] .................................................................................... 123
Configure DRAM Timing by SPD [Enabled] ..................................................... 123
Memory Hole [Disabled]..................................................................................... 124
Boots Graphics Adapter Priority [PEG/PCI]..................................................... 124
Internal Graphics Mode Select [Enable, 8MB] ................................................. 125
PEG Force X1 [Disabled].................................................................................... 125
DVMT Mode Select [DVMT Mode]...................................................................... 126
DVMT/FIXED Memory [128MB] .......................................................................... 126
Boot Display Device [Auto]................................................................................ 126
Flat Panel Type [640*480]................................................................................... 127
Local Flat Panel Scaling [Auto] ......................................................................... 127
TV Connector [Auto]........................................................................................... 127
TV Standard [VBIOS-Default]............................................................................. 127
Audio Controller [Azalia].................................................................................... 128
OnBoard LAN1 (BCM5787M) [Enabled] ............................................................ 129
OnBoard LAN2 (BCM5787M) [Enabled] ............................................................ 129
Save Changes and Exit ...................................................................................... 130
Discard Changes and Exit ................................................................................. 130
Discard Changes................................................................................................. 130
Load Optimal Defaults........................................................................................ 130
Load Failsafe Defaults........................................................................................ 130
Page 154
IEI® Technology, Corp.
KINO-9452 Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 155
KINO-9452 Motherboard
Appendix
B
B Watchdog Timer
Page 156
IEI® Technology, Corp.
KINO-9452 Motherboard
NOTE:
The following discussion applies to DOS environment.
IEI support is
contacted or the IEI website visited for specific drivers for more
sophisticated operating systems, e.g., Windows and Linux.
The Watchdog Timer is provided to ensure that standalone systems can always recover
from catastrophic conditions that cause the CPU to crash. This condition may have
occurred by external EMI or a software bug. When the CPU stops working correctly,
Watchdog Timer either performs a hardware reset (cold boot) or a Non-Maskable Interrupt
(NMI) to bring the system back to a known state.
A BIOS function call (INT 15H) is used to control the Watchdog Timer:
INT 15H:
AH – 6FH Sub-function:
AL – 2:
Sets the Watchdog Timer’s period.
BL:
Time-out value (Its unit-second is dependent on the item “Watchdog
Timer unit select” in CMOS setup).
Table B-1: AH-6FH Sub-function
Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value
is not zero, the Watchdog Timer starts counting down. While the timer value reaches zero,
the system resets. To ensure that this reset condition does not occur, calling sub-function
2 must periodically refresh the Watchdog Timer. However, the Watchdog timer is disabled
if the time-out value is set to zero.
A tolerance of at least 10% must be maintained to avoid unknown routines within the
operating system (DOS), such as disk I/O that can be very time-consuming.
Page 157
KINO-9452 Motherboard
NOTE:
When exiting a program it is necessary to disable the Watchdog Timer,
otherwise the system resets.
Example program:
; INITIAL TIMER PERIOD COUNTER
;
W_LOOP:
MOV
AX, 6F02H
;setting the time-out value
MOV
BL, 30
;time-out value is 48 seconds
INT
15H
;
; ADD THE APPLICATION PROGRAM HERE
;
CMP
EXIT_AP, 1
JNE
W_LOOP
;is the application over?
;No, restart the application
MOV
AX, 6F02H
;disable Watchdog Timer
MOV
BL, 0
;
INT
15H
;
; EXIT ;
Page 158
IEI® Technology, Corp.
KINO-9452 Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 159
KINO-9452 Motherboard
Appendix
C
C Address Mapping
Page 160
IEI® Technology, Corp.
KINO-9452 Motherboard
C.1 IO Address Map
I/O address
Description
Range
000-01F
DMA Controller
020-021
Interrupt Controller
040-043
System time
060-06F
Keyboard Controller
070-07F
System CMOS/Real time Clock
080-09F
DMA Controller
0A0-0A1
Interrupt Controller
0C0-0DF
DMA Controller
0F0-0FF
Numeric data processor
1F0-1F7
Primary IDE Channel
2E8-2EF
Serial Port 4 (COM4)
2F8-2FF
Serial Port 2 (COM2)
378-37F
Parallel Printer Port 1 (LPT1)
3B0-3BB
Intel 945GM Graphics Controller
3C0-3DF
Intel 945GM Graphics Controller
3E8-3EF
Serial Port 3 (COM3)
3F6-3F6
Primary IDE Channel
3F7-3F7
Standard floppy disk controller
3F8-3FF
Serial Port 1 (COM1)
Table C-1: IO Address Map
C.2 1st MB Memory Address Map
Memory address
Description
00000-9FFFF
System memory
A0000-BFFFF
VGA buffer
F0000-FFFFF
System BIOS
1000000-
Extend BIOS
Table C-2: 1st MB Memory Address Map
Page 161
KINO-9452 Motherboard
C.3 IRQ Mapping Table
IRQ
Description
IRQ
Description
IRQ0
System Timer
IRQ8
RTC clock
IRQ1
Keyboard
IRQ9
ACPI
IRQ2
Available
IRQ10
COM 4
IRQ3
COM2
IRQ11
COM 3
IRQ4
COM1
IRQ12
PS/2 mouse
IRQ5
SMBus Controller
IRQ13
FPU
IRQ6
FDC
IRQ14
Primary IDE
IRQ7
Parallel port
IRQ15
Secondary IDE
Table C-3: IRQ Mapping Table
C.4 DMA Channel Assignments
Channel
Function
0
Available
1
Available
2
Floppy disk (8-bit transfer)
3
Available
4
Cascade for DMA controller 1
5
Available
6
Available
7
Available
Table C-4: DMA Channel Assignments
Page 162
IEI® Technology, Corp.
KINO-9452 Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 163
KINO-9452 Motherboard
D Index
Page 164
IEI® Technology, Corp.
KINO-9452 Motherboard
3D graphic, 16
L1 cache, 16, 87
Acoustic Echo Cancellation, 31
L2 cache, 16, 24, 87
ALC883, 6, 19, 30, 31, 132, 143
LCD backlight, 18, 27, 35, 43
AMI BIOS, 5, 20, 29, 81, 82, 84
LCD panel, 78
ASF2.0, 20
LCD voltage, 18, 36, 75
ATX power, 20, 48
memory module, 19, 67, 72
Audio jacks, 18, 55
Mini PCI, 4, 16, 18, 19, 35, 46, 47
Beam Forming, 31
Mini-ITX, 16
CD-ROM, 56, 90, 92, 109
multi media application, 16
Center/Subwoofer port, 56
Noise Suppression, 31
chassis, 37, 38, 55, 78
Northbridge, 3, 19, 25, 35, 37
Clear CMOS, 5, 18, 36, 75, 76, 77
On-Die Termination, 25
Core™ Duo, 3, 16, 19, 23, 24
PCB board, 65
Core™ Solo, 3, 16, 19, 23, 24
PCBEEP, 30
CPU cooler, 32, 66
PCI, 3, 6, 13, 16, 18, 19, 20, 26, 27, 28, 35,
DAC channel, 30
46, 47, 83, 101, 102, 109, 110, 111, 112,
DB-9, 36, 60, 74
113, 114, 124, 125
DDR2, 16, 17, 19, 25, 27, 31, 35, 67, 71
power consumption, 24, 31
Digital I/O, 17, 19
PS/2, 59, 60, 79, 117, 118, 162
DMA controller, 26, 162
RAMDAC, 26
DMI lane, 25
RJ-45, 36, 55, 58, 59, 79
Dual-core, 16, 24
RoHS, 16
DVD player, 31, 56
rotation signal, 37
Electrostatic discharge, 64
RS-232 cables, 32, 66, 73
front panel, 30, 38, 39
RS-232/422/485 cable, 32, 66
Front panel, 17, 35
SATA cables, 32, 66, 73
HDTV, 16, 17, 19, 27, 32, 66, 73
SATA II, 16, 18, 19, 28, 51
High Definition Audio, 26, 30, 79, 128
SATA power cable, 32, 66, 73
I/O shielding, 32, 66
SDVO, 25, 27
IC chips, 65
Side Speaker Out port, 56
ICH7-M, 3, 19, 25, 26
socket 479, 69
Integrated Heat Sink, 68
SPDIF, 4, 18, 35, 53, 54
Intel 945GM, 3, 19, 25, 26, 161
SpeedStep technology, 24, 25
Intel Active Management Technology, 26
Spread spectrum clocking, 27
Intel Matrix Storage Technology, 26
Streaming SIMD Extensions 3, 24
Page 165
KINO-9452 Motherboard
SuperIO, 85
TV-Out, 4, 18, 25, 27, 36, 56, 61, 62
TFT panel, 27
USB 2.0, 17, 18, 19, 26, 29, 36, 54, 56, 106
Page 166
IEI® Technology, Corp.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement