LED-192 W User Manual

LED-192 W User Manual
EC - Declaration of Conformity
LED STROBE W
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL: 2000+A12: 2002
Safety of household and similar electrical appliances
Part 1: General requirements
LED-192 W
User Manual
Innovation, Quality, Performance
11B
Please read the instructions carefully before use
C. Some fixtures don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the fixture. Set the proper address.
D. No response to the sound
1. Make sure the fixture does not receive DMX signal.
TABLE OF CONTENTS
2. Check microphone to see if it is good by tapping the microphone.
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
1. Safety Instructions
2. The motor’s drive IC on the PCB might be out of condition.
2. Technical Specifications
8. Fixture Cleaning
3. Main Function
4. How to control the fixture
5. DMX 512 Configuration
6. DMX 512 Connections
The cleaning of internal must be carried out periodically to optimize light output. Cleaning
frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics.
y Clean with soft cloth using normal glass cleaning fluid.
y Always dry the parts carefully.
y Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
7. Troubleshooting
8. Fixture Cleaning
1B
10B
1.
Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the
1. Safety Introductions
fixture to the input of the next fixture. The cable cannot be branched or split to a “Y”
cable. Inadequate or damaged cables, soldered joints or corroded connectors can
2.
easily distort the signal and shut down the system
Please read the instructions carefully which includes important
The DMX output and input connectors are pass-through to maintain the DMX circuit
information about the installation, operation and maintenance.
when no power is connected to the fixture.
3.
At last fixture, the DMX cable has to be terminated with a terminator to reduce signal
WARNING
y
errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a
4.
user, be sure that they also receive this instruction booklet.
3-pin XLR-plug and plug it in the DMX-output of the last fixture.
y
Unpack and check carefully there is no transportation damage before using the fixture.
Each lighting fixture needs to have an address set to receive the data sent by the
y
Before operating, ensure that the voltage and frequency of power supply match the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
5.
Please keep this User Manual for future consultation. If you sell the fixture to another
3 pin XLR connectors are more popular than 5 pins XLR.
power requirements of the fixture.
y
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
y
Disconnect main power before servicing and maintenance.
y
Use safety chain when fixes this fixture.
y
Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is
higher than this.
7. Troubleshooting
y
In the event of serious operating problem, stop using the fixture immediately. Never try
Following are a few common problems that may occur during operation. Here are some
to repair the fixture by yourself. Repairs carried out by unskilled people can lead to
suggestions for easy troubleshooting:
damage or malfunction. Please contact the nearest authorized technical assistance
center. Always use the same type spare parts.
y
Do not connect the device to any dimmer pack.
1. Check the connection of power and main fuse.
y
Do not touch any wire during operation and there might be a hazard of electric shock.
2. Measure the mains voltage on the main connector.
y
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain
A. The fixture does not work, no light and the fan does not work
or moisture.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
y
The housing must be replaced if they are visibly damaged.
2. If the DMX LED is on and no response to the channel, check the address settings and
y
Do not look directly at the LED light beam while the fixture is on.
y
There are no user serviceable parts inside the fixture. Do not open the housing or
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
attempt any repairs by yourself. In the unlikely event your fixture may require service,
please contact your nearest dealer.
of the fixture or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
9B
For power supply, do not connect in series much more than 33 units, use
another mains supply for next 33 units.
2B
2. Technical Specifications
y
5. DMX512 Configuration
It can be operated by DMX512 control or can be used as an individual unit without
controller.
y
It can be linked together as many as required in master/slave mode, and perform the
great built-in programmed lighting shows triggered by music.
y
Please use a 3 pin XLR cable/plug when connecting them together.
y
It features different pre-programmed chase patterns.
y
Power supply
Input Voltage:AC 100V-240V 50-60Hz
y
Power consumption:18W
y
LED : Total 192pcs White
y
Dimension: 315mm x 181mm x 114mm
y
Weight: 2.1KG
6. DMX512 Connections
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
3. Main Function
To select any functions, press MENU button until the required one is shown on the display.
Select the function by ENTER button and the display will blink. Use DOWN and UP button to
change the mode. Once the required mode has been selected, press ENTER button to
setup or it will automatically return to the main functions without any change after idling 10
seconds. Back to the functions without any change press MENU button. The main functions
are shown below:
3B
8B
LED will flash to the music. The other units will have to set in slave mode
(normal) or
and select
(2 light show) mode, Their DMX cables plugged into the DMX
input jacks (daisy chain) and the slave led lights will constantly on.
2-light show
In
(slave mode),
means the unit works normally and
means
2-light show. In order to create a great light show, you can set
on the second unit to
get contrast movement to each other, even if you have two units only.
B. Universal DMX controller
If you use an universal DMX controller to control the units, you have to set DMX address
from 1 to 512 channel so that the units can receive DMX signal.
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when
the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again.
Please refer to the following diagram to address your DMX512 channel for the first 4 units:
DMX 512 Address Setting
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX 512 address.
C. Easy Controller (by CA-8)
The easy remote control is used only in master/slave mode. There is a terminator for
connect the easy controller inside the fixture. By connecting the cable into DMX IN
waterproof cable entry gland to the CA-8 terminator of the first fixture, you will find that the
remote control on the first fixture will control all the other fixtures for Stand by, Function and
Once the address has been selected, press ENTER button to setup or automatically return
to the main functions without any change after 8 seconds. Back to the previous functions
without any change press MENU button.
Slave Mode
Mode functions.
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button, Use DOWN and UP button to select the
Blackout
Blackout the unit
Function
1. Synchronous Strobe
2. Sound Strobe
3. Two light Strobe
Dimmer
Mode
Sound/Strobe
(LED OFF)
LED ON
or
(Slave Mode 1 and 2). Back to the previous functions without any change press
MENU button.
Sound Mode
Press the MENU button until the
7B
(Master Mode) or
is showing on the display. Pressing ENTER button
4B
and the display will blink. Use DOWN and UP button to select the
(sound on) or
Display Inverse
(sound off) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
go back to the functions without any change press the MENU button again.
when the
is blinking on the display. Use the ENTER button to change to the mode
(display inversion), It will automatically store after 8 seconds. Or press the ENTER
Blackout Mode
button again return to the mode
Press the MENU button up to when the
is showing on the display. Pressing
(display normal). To go back to the functions press
the MENU button.
ENTER button and the display will blink. Use DOWN and UP button to select the
Display normal mode for the fixture putting on the floor.
(yes blackout) or
Display inversion mode for the fixture fixing under ceiling.
(no blackout) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
Fixture Hours
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the display will show the number of working hours of the unit. To go back to the
Show Mode
functions press the MENU button again.
is showing on the display. Pressing ENTER
Press the MENU button up to when the
button and the display will blink. Use DOWN and UP button to select the
(Auto) or
(Menu) mode. Once the mode has been selected, press the ENTER button to
Software version
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
setup or automatically return to the main functions without any change after 8 seconds. To
button and the display will show the version of software of the unit. To go back to the
go back to the functions without any change press the MENU button again.
functions press the MENU button again.
Menu Mode
is showing on the display. Then Use
Press the MENU button up to when the
DOWN and UP button to select
, Pressing ENTER button and the display will blink.
or
Use DOWN and UP button to select the
mode .Once the mode has
been selected, press the ENTER button to setup or automatically return to the main
functions without any change after 8 seconds. To go back to the functions without any
change press the MENU button twice.
4. How to control the fixture
Three ways to operation:
A. Master/Slave operation
B. Universal DMX controller
C. Easy controller CA-8
LED
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
or
A. Master/Slave operation
By linking the units in master/slave connection, the first unit will control the other units to
mode. Once the mode has been selected, press ENTER button to setup or automatically
give an automatic, sound activated, synchronized light show. This function is good when you
return to the main functions without any change after 8 seconds. Back to the functions
want an instant show. You have to set the first unit in master mode
without any change press MENU button again.
jack will have nothing plugged into it, and Its master LED will be constantly on and sound
5B
6B
. Its DMX input
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement