Mini High Speed Dome Camera

User Manual

Contents

1. Introduction

Features……………………………………………………………………… .....

2

Specifications………………………………………………………………...

....

4

2. Installation

DIP Switch Setup……………………………………………........................ 6

3. Operation

Control……………………………………………………………................... 10

4. How to use OSD Menu

ADDR setting………………………………………………………………… ... 13

Motion………………………………………………………………………… ....

13

Patterns………………………………………………………………………..

...

16

Camera………………………………………………………………………..

....

17

Cruise Setting………………………………………………………………… ...

28

Display Setup………………………………………………………………… ...

29

Reboot System………………………………………………………………..

..

30

Exit…………………………………………………………………………… .....

30

5.Trouble Shooting

6.Safety Information

Safety information…………………………………………………………….

...

31

1

1. Introduction

1.1 Features

※ Camera Specifications:

CCD Sensor: 1/4″ Interline Transfer CCD.

Zoom Magnification: 10X Optical zoom, 10X Digital zoom.

Day & Night function : The camera is configured to switch to the black and white

mode automatically under low light conditions and at night with mechanical IR

Cut filter for clear images.

Various focus mode: Auto Focus / Manual Focus / Semi-Auto Focus.

※Powerful Pan / Tilt Functions

Max. 360°/sec high speed Pan / Tilt motion.

Automatic turn over.

Support bearing indication.

Programmable cruise and presets.

Soft address enables to set up the address and number of the camera.

Adopt Vector Drive Technology, Pan / Tilt motions are accomplished in a shortest

path . As a result , time to target view is reduced seriously and the video on the

monitor is very nature to watch.

For jog operation using a controller , since ultra slow speed 0.05°/sec can be

reached. It is very easy to locate camera to desired target view.

Support zoom proportional Pan / Tilt speed. Camera can be moved to a desired

position in accurate manner even through high zoom ratio.

※Preset, Linear, Preset position cruise, Pattern, Auto Scan.

Max. 256 presets are assignable and characteristics of each preset can be set up

independently.

Linear scan enables to move camera repetitive between two preset positions with

assigned speed.

Preset position cruise: the group can have max 30 entities of preset. This enables

for camera to move a combinations of this functions repetitively.

2

4 Patterns with 100 commands can be recorded and executed. This enables the

camera to track a surveillance trajectory as closely as possible.

360° continuous scan.

360° intermittent scan. The camera will have seconds stop during each 90°turning.

Auto scan : this enables to move the camera to execute the certain scan when no-

operation for a long time.

Reserved Presets for special purpose : besides regular 256 presets, direct calling

of reserved presets enable to set up many of camera functions with / without using

OSD menu.

※PTZ( Pan /Tilt /Zoom) Control

RS485 Communication.

Pelco D / Pelco P, special protocols available.

※OSD (On screen Display) Menu

OSD menu is provided to display the status of camera and to configure the functions

interactively.

2 Language are supported.

Each display item can be turned ON or OFF independently.

3

1.2 Specifications

Video Signal System NTSC PAL

CCD 1/4〞Interline Transfer CCD

Max. Pixels 811(H) x 508(V) 795(H) x 596(V)

Horizontal Resolution 500TV Line(Color), 570 TV Line(B/W)

S/N Ratio 50dB(AGC off)

Camera

Zoom X10 Optical Zoom, X10 Digital Zoom

Focal Length F1.8, f=3.8~38mm

Min. illumination 0.7Lux(Color),0.02Lux(B/W), F1.8, 50 IRE

Day & Night Auto / Day/ Night function (ICR)

Focus Auto / Manual/ SemiAuto

Iris Auto / Manual

Shutter Speed 1/50~1/120000 sec

AGC General / High / Off

Pan / Tilt

General

BLC Low / Middle / High / Off

DNR Low / Middle / High / Off

Pan :0~360°(Endless) Tilt: 0~180°

Range

Preset : 360°/sec

Pan/Tilt Speed

Manual: Pan 300°/sec; Tilt 180°. (proportional to zoom)

Auto Pan : 1~180°/sec adjustable

Preset 256 Preset(Label, Camera Image Setting)

Cruise Auto Pan, Pattern, Scan.

Other Functions Auto Flip, Auto Parking, Power up Action etc.

Communication RS-485

Protocol Pelco-D, Pelco-P, Special protocols available

Baud rate 2400, 4800, 9600

Language English

4

2. Installation

2.1 Installation and Connection

2.1.1. Wall Mount

(1) Connect Camera

Plug the terminals into the bottom of the main unit, then, fix the main unit with

screws supplier.

power

485 data cable

BNC Video

(2) Bracket Installation

Use the screws provided to secure the wall mount to the wall.

2.1.2.Ceiling Mount

(1) Fix the main unit on the bracket.

After wiring cables to terminals , plug the terminals into the bottom of main unit .

Then, fix the main unit with screws provided

The cable cross through bottle position and be out of breach of bottle position

5

(2)Install ceiling mount bracket on the ceiling using screws provided.

54

12

8

5 .

5

2.1.3 Cabling

Connector Interface

DC 12V

485A Red

485B Black

BNC Video

2.2 DIP Switch Setup

Before you install the camera, you should set the DIP switches to configure the camera

ID, Baud rate, and communication protocol.

Default ID : 1

Baud rate: 2400

Protocol: Pelco-D.

6

2.2.1 Camera ID Setup

ON

OFF

1 2 3 4 5 6 7 8

The range of ID is 0~255. Factory default of Camera ID is 1.

ID number of camera is set using binary number. The number from 1~8 present 1, 2, 4,

8, 16, 32, 64, 128. For example, switch 1, 3, 5, 7 to “ON” position, the corresponding

ID should be 1+4+16+64=85.

The example is shown below.

ID No

0

1

2

3

4

5

6

7

8

Code Switch

1 2 3 4 5 6 7 8

0 0 0 0 0 0 0 0

1 0 0 0 0 0 0 0

0 1 0 0 0 0 0 0

1 1 0 0 0 0 0 0

0 0 1 0 0 0 0 0

1 0 1 0 0 0 0 0

0 1 1 0 0 0 0 0

1 1 1 0 0 0 0 0

0 0 0 1 0 0 0 0

ID No

10

20

30

50

100

101

150

200

255

Code Switch

1 2 3 4 5 6 7 8

0 1 0 1 0 0 0 0

0 0 1 0 1 0 0 0

0 1 1 1 1 0 0 0

0 1 0 0 1 1 0 0

0 0 1 0 0 1 1 0

1 0 1 0 0 1 1 0

0 1 1 0 1 0 0 1

0 0 0 1 0 0 1 1

1 1 1 1 1 1 1 1

2.2.2 Communication Protocol and Baud rate Setup

ON

OFF

1 2 3 4

7

Select the appropriate protocol with DIP switch combination.

Pin No

Protocol

Baud rate

Switch State

1 2

OFF OFF

ON OFF

OFF

ON

ON

ON

3 4

OFF OFF

ON OFF

OFF ON

ON ON

Protocol

PELCO-P

PELCO-D

Auto

Reserved

9600

2400

4800

9600

3.Operation

3.1 Check points before operation

Before power is connected, please check the cables carefully.

The camera ID of the controller must be identical to that of the camera to be controlled.

The camera ID can be checked in the System Information of OSD Menu.

If you controller supports multi-protocols, the protocol must be changed to match to

that of the camera.

If you change camera protocol by changing DIP switch , the change will be effective

after you reboot the camera.

Since the operation method can be different for each controller available , refer to the

manual for your controller if camera can not be controller properly.

3.2 Operation

Note: The manual will refer to our CCTV tester to explain how to operate and control the camera.

8

3.2.1 Preset function pre-check

Check how to operate preset , Scan, Auto Pan and Pattern function with controller or DVR in advance to operate camera function using them.(refer to your System keyboard Manual)

If controller or DVR has no pattern button or function , use shortcut keys with preset numbers. For more information, refer to “Reserved Preset” in this manual.

Use “UP, DOWN, LEFT, RIGHT” direction key to move to a desired position,，then, press ”Zoom, Lens, Iris” to adjust the pictures.

Press “preset setup” to input number, then confirm by a press on setup key.

Call Preset

Press “ Call Preset ” key and input No of preset , the confirm by a press on “Setup” key , the camera will move to the desired preset , meanwhile , the zoom, lens and iris will automatically change to preset states

3.2.2 Reserved Preset

Some Preset numbers are reserved for direct access to specific functions in OSD menu . These direct commands via preset provide quick execution of various functions using keyboard controller as well as simplify the interface with DVR and

IP equipments.

Reserved Preset Function

Go/Set Preset <95> Enters into OSD menu

Go Preset <80> Reserved.

Go Preset <82> Runs cruise function

Go Preset <83> Clean all presets

Go Preset <84 ~ 87> Runs Pattern 1 ~ 4

Go Preset <88> Reserved ( Runs wide dynamic function)

Go Preset <89> Reserved (Stop wide dynamic function)

Go Preset<96> Runs 360° scan(pause 3 seconds per 90°)

Go Preset <97> Runs linear scan

Go Preset <98> Runs cruise function

Go Preset <99> Runs Auto pan function

9

3.3 Camera Lens control

3.3.1 Zoom

Adjust the lens distance to enlarge or downsize the image for best effect or wideangle effect.

Using “ZOOM IN / TELE” key to enlarge the images.

Using “ZOOM OUT/ WIDE” key to downsize the images.

3.3.2 Focus

Adjust definition of the object of scene

Press “Focus Far” key to shorten the distance of far scene.

Press “Focus Near” key to shorten the distance of near scene.

3.3.3 Iris

Press “Iris Open” key to adjust the brightness.

4.How To Use OSD Menu

After power up or restart, the present Protocol, Baud rate and Address will be displayed on the screen as below:

PTOL： PELCO-P

COMM：2400、N、8、1

ADDR： 1

4.1 Basic operation of Main menu

Go <Preset 95> to enter into main menu.

Using “Iris open” and “Iris close” to confirm or exit main menu.

Using “UP/DOWN” keys or joystick to move cursor to sub-menu, press “Iris open” to enter into menu.

Using “UP/DOWN” keys or joystick to move cursor to the function and press ”Iris open” to choose the function.

Using “UP/DOWN” keys or joystick to set up and press “Iris open” to save.

Move the cursor to “BACK” and press “Iris open” to back to main menu.

Note: There might display different information due to different camera.

4.2 Main menu

MAINMENU

SYSTEM INFORMATION

ADDR SETTING

MOTION

PATTERNS

CAMERA

CRUISE SETTING

DISPLAY SETUP ON

RESTORE FACTORY DEFAULT

REBOOT SYSTEM

EXIT

<SYSTEM INFORMATION>：Shows system information.

<ADDR SETTING>：Select and setup Soft/Hard address.

<MOTION>：Setup for motion related settings.

<PATTERNS>：Setup for Patterns.

<CAMERA>：Configure Camera related functions and data.

<CRUISE SETTING>：Setup presets scan.

<DISPLAY SETUP>：Enable / Disable of OSD display on main screen.

<RESTORE FACTORY DEFAULT>：Restore factory settings.

<REBOOT SYSTEM>：Reboot the system.

4. 2. 1 System Information

SYSTEM INFORMATION

COM 2400 、 N 8 1

ADDRESS 1

PROTOCOL PELCO-P

PRESETS 256

SOFTWARE VERSION V5.2

BACK

EXIT

<COM>：Shows current Baud rate.

<ADDRESS>：Shows current Camera ID for PTZ control, 0~255.

<PROTOCOL>：Shows current protocol for PTZ control.

<PRESETS>：Shows the preset numbers.

<SOFTWARE VERSION>：Shows current software version of camera.

Notice: the system information can not be changed.

4. 2. 2 Address Setting

ADDR SETTING

ADDR TYPE HARD

ADDR SOFT 3

ADDR HARD 1

BACK

EXIT

ADDR TYPE：Choose the address type (Hard/Soft Add), when you choose soft type, the user can setup the address by remote access.

ADDR SOFT：setup soft address . Press UP/DOWN” keys of your controller and setup the camera ID from 0~254.

ADDR HARD: Setup hard address. Only can be changed by DIP Switch.

Notice: Please reboot the dome camera after reset the camera ID.

4.2.3 Motion

MOTION

SET FRAME SCAN

POWER UP PATTERN 4

PARK TIME 15S

PARK ACTION PATTERN 4

FRAME SCAN SPEED 16

RNADOM SCAN SPEED 16

BACK

EXIT

Motion setup is to setup preset and packing action function.

SET FRAME SCAN：setup the LEFT/RIGHT extreme position between two presets.

POWER UP ：This function enables to resume the last action executed before power down.

NONE : No action.

CRUISE: Cruise action between presets position.

AUTO SCAN: 360°continious scan.

RANDOM SCAN: 360°intermittemt scan action. FRAME SCAN：

PARK TIME : Parking action during idle time.

Time setting: 15-60 (Seconds) ,2…60M（Minutes）, 2…12H（Hours）

PARK ACTION ：This function enables to locate the camera to specific position automatically if operator doesn’t operate the controller for a while. The Park Time can be defined as an interval.

FRAME SCAN SPEED: Set the speed between two presets from1~32.

RANDOM SCAN SPEED: set the speed of 360° continuous and intermittent scan.

Set Frame Scan

FRAME SCAN

SET SCAN POSITION

CLEAR FRAME SCAN

BACK

EXIT

SET SCAN POSITION：Set up scan range between two positions (Left/Right extreme position).

CLEAR FRAME SCAN：Deletes frame scan.

1. Set Scan Position

(1) Move the cursor to <Set Scan Position> and enter below interface.

SET FFRAME SCAN

LEFT LIMIT POSITION

IRIS OPEN TO CONTINUE

(2) Move the cursor to choose the extreme position of preset by using “ Left / Right ” keys

or joystick of your controller, then press “Iris Open” to enter below interface:

SET FFRAME SCAN

RIGHT LIMIT POSITION

IRIS OPEN TO CONTINUE

2. Clear Frame Scan

CLEAR FFRAME SCAN

IRIS OPEN TO CONTINUE

Move the cursor to “Clear Frame Scan” to enter, the press “Iris Open” to delete the extreme positions.

4.2.4 Patterns

PATTERNS

PATTERN NUMBER

PROGRAM PATTERN

CLEAR CURRENT PATTERN

CLEAR ALL PATTERN

EXIT

BACK

4 Patterns are supported, please refer to below details:

<PATTERN NUMBER>：Set Pattern number (1~4).

<PROGRAM PATTERN>: Pattern scan program.

<CLEAR CURRENT PATTERN>：Deletes data in current pattern.

1．Pattern Number

(1)Move the cursor to “PATTERN NUMBER” by using direction keys and select pattern

number, then press “Iris OPEN” to confirm.

2. Program Pattern

(1)Move the cursor to “Program Pattern” by using direction keys or joystick of your

controller and press “IRIS OPEN” to enter below interface.

PROGRAM PATTERN

USE THE JOYSTICK OR

KEYBOARD TO MOVE THE

CAMERA TO THE

STARTING POSITION

IRIS OPEN TO CONTINUE

(2)Using keyboard or joystick of your controller to locate the start position, then press

“Iris Open” to enter.

PATTERNS

STORAGE USED

(3)Using keyboard or joystick of controller to edit pattern route and action, Max 100

actions, then press “Iris Open” to save.

4.2.5 Camera setup

We are using Samsung SDM-100P camera to explain below operation.

Main Menu

Camera label Off

White Balance Auto

BLC Off

Auto Detection Off

Focus

Exposure

Additional Menu

Back

Exit for sub-menu.

1.Camera Label setup：press “Iris Open” to enter sub-menu and edit camera lable.

Camera Label

ABCDEFGHIJKLMNO

PQRSTUVWXYZabcd e f g h I j k l m nopqrs t u v w x y z01234567

89 ( ) < > - / # * ! ? , .

Clean Position Exit

Using cursor to select the letter, then press “Iris Open” key to save the setup.

2. White Balance setup

WB Mode: Auto Trace / Manual / Auto

2.1 Auto Trace : Indoor/Outdoor, The camera can automatically adjust ambient light

from 1800K~10500K（Indoor ：3000～10,500K; Outdoor：1,800～10,500K，）to

ensure the most nature image effect.

Auto Trace WB

Auto Trace WB mode Outdoor

Exit

2.2 Manual: Close auto WB, adjust Red and Blue level manually.

Manual WB

Red 30…|..……….

Blue 41…..…|…….

Exit

Red adjust range: 0~100 Blue adjust range: 0~100

2.3 Auto BW : This mode is the most accurate and reliable for most places.

3. Backlight Compensation setup

Backlight High/Middle/Low/Off

4.Motion Detection setup

Match the Alarm sensor input to one of preset positions. If an external sensor is activated, camera will move to corresponding preset position when this item is predefined.

Alarm : On/Off

Region：1~4

Region Mode: On / Off

Motion Detection

Alarm On/Off

Select Region 1

Region Mode On

Top 20…|..……….

Bottom 25….…|…….

Left 20…|.……….

Right 40….……|….

Exit

5.Focus Setup

Focus

Mode Auto

Zoom trace mode On

Zoom trace speed Fast

Digital Zoom On

Show Zoom Off

Initial Zoom Position Off

Lens Initialization

Exit

1.Mode：Auto, Manual, One-off Auto focus. Press “Iris Open” to enter sub-menu.

One-off auto focus: Once the image zoom changes, the camera will automatically

focus and fix the status till the image change again.

Notice: do not use Auto Focus under the below conditions.

The target is too dark (such as black clothes or curtains).

The target is very smooth( like car surface)

The brightness contrast of the target is not very clear.

Too strong high light or back light.

Too high contrast.

Some shade in front of the target.

(1) Auto mode setup:

Setup Zoom

Zoom in Zoom out

Back : press “SET” key

Using the direction keys to enlarge or downsize, press “ Iris/Open” key to back.

(2) One-off Auto focus and Manual focus Adjustment:

Setup Zoom

Zoom in Zoom out

Near Far

Back : press “SET” key

2. Zoom trace mode:

Manual Focus: Off. Auto and One-off Auto Focus: On / Off.

3. Zoom trace speed: Fast/Slow.

4. Digital zoom: On / Off , range: X2~X10.

Digital Zoom

Digital Zoom X2

Exit

5.Show zoom: On / Off.

6.Initial zoom position：Using direction keys to move the cursor to “On”, then press

“Iris Open” to set up.

Initial Zoom Position

Initial Zoom Position X1

Exit

Zoom range: X1~X10

7. Lens Initialization: press “Iris open/Set” key to initialize the lens.

8. Exposure setup:

Exposure

Brightness 25….…|…….

Iris Auto

Shutter ——

AGC Off

SSNR Off

SENS-UP Off

Exit

Brightness range: 0~100.

Iris：Auto/ Manual. Press “Iris Open” to enter into manual setup

Manual Iris

Iris 100….………|

Exit

If the number of iris is set to higher, the image will be brighter.

Shutter mode

: Flicker / Manual / Auto

The shutter speed of Anti-flash is 1/100（NTSC） ，1/120（PAL）

Manual mode setting (PAL）: 2X、4X、6X、8X、10X、12X、14X、16X、24X、32X、

64X、128X、1/120000、1/60000、1/30000、1/10000、/ 1/7000、1/5000、1/2500、

1/1600、1/1000、1/700、1/500、1/250、1/100、1/50.

Manual shutter

Shutter 1/50

Exit

Notice: Auto shutter setting only for manual iris mode.

AGC: High / Middle/ Low / Off.

Enhances image brightness automatically in case that luminance level of image signal is too low.

Range: 5-41

AGC

Level 5

Exit

SSNR：High / Middle / Low / Off

Enhances images by reducing noises when gain level of images too high.

Sens-up: Manual / Off

Adjust CCD exposure time.

Auto mode setting:2X、4X、6X、8X、10X、12X、14X、16X、24X、32X、64X、128X.

Sens-up

Sens up X4

Exit

9 .Additional menu:

Additional menu

User setup Off

Privacy zone mask Off

Day & Night Auto 1

Sync. system Internal

Image adjustment

EXIT

( 1 )User preset setup: On / Off

User Preset

User preset number No 1

User preset mode Off

Save

Clear

Exit preset not setup.

8 user preset number, 1~8.

User Preset mode: use direction keys to “On” and press “Iris/Open” to setup.

User preset mode

Focus

Exposure

Other

Exit

Focus: Using direction keys to “Focus” and press “Iris/Open” key to set up.

Focus

Mode Auto

Zoom trace mode On

Zoom trace speed Fast

Digital zoom On

Show zoom Off

Exit

Other：refer to below details.

Other

Camera Type Off

BW Auto trace BW

BLC Off

Motion Detection Off

Privacy mask Off

Day & Night Outer

Horizontal flip Off

Vertical flip Off

Exit

(2) Privacy mask

Privacy mask

Group selection 1

Area selection 1

Zone mode Off

Color 50…|..……….

Top 50…|..……….

Bottom 104….…|…….

Left 50…|.……….

Right 98….……|….

Exit

Group selection：1~ 8

Area selection: 1~4 zone / group

Zone mode: On / Off

Color: color, range of privacy zone is 0~100.

Top: ordinate position on the top of zone.

Bottom: ordinate position on the bottom.

Left: horizontal abscissa position on the left side.

Right: horizontal abscissa position on the left side.

(3) Day / Night: Day and Night function. Auto 1/ Auto 2 / Outer/ Color/ B&W mode.

B&W mode: suit for night work.

Color mode: suit for daytime.

Auto mode: change day and night mode automatically according to the environment

illumination. Auto 1 is faster than Auto 2.

(4) Synchronous mode: internal, unchangeable.

(5) Image adjustment.

Image adjustment

Freeze Off

Horizontal flip Off

Vertical flip Off

Sharpness On

Hue 50….…|…….

Exit

Freeze : Camera starts freezing the image of start point , as soon as camera stops at preset end point, camera starts display live images.

Horizontal flip : image will flip 180° when you start up . Normal when shutdown.

Vertical flip: image will slip 180°when you start up, and normal when shutdown.

Sharpness: adjust the sharpness of the edges. Range: 0~31.

Sharpness

Sharpness 8…|.……….

Exit

Hue: adjust the image hue, range: 0~100.

Re-boot: restart the camera.

Exit: exit camera menu.

4.2.6 Cruise Setting.

CRUISE

DWELL TIME<SECS> 6

PRESET LIST 1

1 ON 0 OFF

1234567890 PRESET

1101111111 [1-10]

BACK

EXIT

Auto cruise : set up preset scan route.

<Dwell Time (Sec)>: preset cruise dwell time, range:1～250 Sec.

<Preset List>: 3 pages.30 presets.

<1234567890>：preset position in the preset list.

<110111 1111>：1 means the preset position corresponding to above preset list is

elected to cruise list; 0 means overleap.

<Back>：save the setup and back to main menu.

<Exit>：Exit OSD menu

4.2.7 Display Setup

Display setup: On/Off, set up the orientation display or not.

Horizontal /Vertical Zoom

236/163 X1

4.2.8 Restore Factory Default.

Move cursor to <RESTORE FACTORY DEFAULT> and press “Iris/Open to restore

factory default.

4.2.9 Reboot System>

Move cursor to <Reboot System > and press “Iris /Open” to reboot the system. Easy

to change the Soft/Hard address by remote and no need to power off.

4.2.10 Exit: Move cursor to <Exit> and press “Iris /Open” to exit the OSD menu.

5.Trouble Shooting

Troubles Reason Solution

Connect wrong cable. Correct the connection

No action, no power on

Bad connection Eliminate the bad connection

Maybe user setup wrong IP,

Out of control after power

Protocol and Baud rate.

up

RS-485 cable reverse connection or disconnection.

Reset IP, Protocol and Baud rate

Check RS-485 connection cable

Video cable is bad connection Eliminate the bad connection

Screen not stable

Power is not enough. Change

Discontinuity

RS-485 cable is bad connection

or disconnection while work

RS-485 cable broken Check RS-485 connection cable

6.Safety Information

1. Transportation

Do not force, shake and marinate during transportation, storage and installation.

2. Installation

Please handle with care, do not press the camera and its' parts when you install,

do not connect before you install the cover.

3. Power cable, Video cable and control cable.

Use shield wire and do not mix with other cables.

4 Electrical safety

Keep the camera or signal transmission wire away from high voltage equipment

or cable (at least 50 meters), take lightning protection and surge protection.

5. Clean

When cleaning , use dry and soft cloth or neutral cleanser to clean the camera cover.

6.Must be sealed closely , do not spray water or liquid onto parts of camera , doing

so may cause damage.

7. Do not use the camera in extreme temperature or humidity environment.

8. Do not install the camera close to air outlet of air condition.

Camera lens will be misty because of water condensation under below conditions:

Extreme temperature change.

The room full of smoking or dust.

9. Do not locate the camera towards extremely bright objects such as sun and

spotlight, as this may damage the CCD image sensor.