Allen-Bradley PanelView 1000e, 1200e 1400e User Manual

Allen-Bradley
PanelView
1000e, 1200e, and
1400e Operator
Terminals
(Cat. No. 2711E-T10C6, 2711E-K10C6,
2711E-T10C7, 2711E-K10C7,
2711E-T10C15, 2711E-K10C15,
2711E-K12C6, 2711E-K12C6L2,
2711E-T12C6, 2711E-T12C4,
2711E-T14C6, 2711E-K14C6,
2711E-T14C7, 2711E-K14C7,
2711E-T14C15, 2711E-K14C15)
User
Manual
Important User
Information
Because of the variety of uses for the products described in this publication, those
responsible for the application and use of this control equipment must satisfy
themselves that all necessary steps have been taken to assure that each application
and use meets all performance and safety requirements, including any applicable
laws, regulations, codes and standards.
The illustrations, charts, sample programs and layout examples shown in this guide
are intended solely for purposes of example. Since there are many variables and
requirements associated with any particular installation, Allen-Bradley does not
assume responsibility or liability (to include intellectual property liability) for actual
use based upon the examples shown in this publication.
Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application,
Installation, and Maintenance of Solid-State Control (available from your local
Allen-Bradley office), describes some important differences between solid-state
equipment and electromechanical devices that should be taken into consideration
when applying products such as those described in this publication.
Reproduction of the contents of this copyrighted publication, in whole or in part,
without written permission of Allen-Bradley Company, Inc., is prohibited.
Throughout this manual we use notes to make you aware of safety considerations:
!
ATTENTION: Identifies information about practices
or circumstances that can lead to personal injury or
death, property damage or economic loss.
Attention statements help you to:
•
•
•
identify a hazard
avoid the hazard
recognize the consequences
Important:
Identifies information that is critical for successful
application and understanding of the product.
PanelBuilder, PanelView, Data Highway Plus, DH+, SLC and SLC 500 are trademarks, and PLC, PLC-2, and PLC-3 are registered
trademarks of Allen-Bradley, Inc.
Modbus is a registered trademark of AEG Schneider Automation, Inc.
Intel is a trademark of Intel Corporation.
IBM, PC, AT, XT, PS/2 and PC DOS are registered trademarks of International Business Corporation.
Epson is a registered trademark of Seiko Epson Corporation.
Microsoft Windows is a trademark, and Microsoft, MS, and MS-DOS are registered trademarks of Microsoft Corporation.
All other brand and product names are trademarks or registered trademarks of their respective companies and are hereby
acknowledged.
Preface
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introducing the PanelView
Terminals
P–1
P–2
P–2
P–3
Chapter 1
Welcome to the PanelView Family . . . . . . . . . . . . . . . . . . . . . . . .
Keypad and Touch Screen Terminals and Software . . . . . . . . . . . . .
Keypad Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touch Screen Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PanelBuilder 1400e Configuration Software . . . . . . . . . . . . . . . .
Features of the PanelView Terminals . . . . . . . . . . . . . . . . . . . . . . .
Additional Features of the PanelView Terminals . . . . . . . . . . . . . . .
Applicable Programmable Controllers and Connections . . . . . . . . .
Remote I/O Communications . . . . . . . . . . . . . . . . . . . . . . . . . .
Logix55xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLC-5/11, 5/15, 5/20, 5/25, 5/30, 5/40, 5/60, 5/80, and 5/250
Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLC-5/10 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLC-3 and PLC-3/10 Processors . . . . . . . . . . . . . . . . . . . . .
PLC-2 Family Processors via 1771-SN or 1772-SD2 . . . . . . . .
SLC-5/02, 5/03, or 5/04 via 1747-SN Series A or B . . . . . . . . .
1771-SN I/O Subscanner Module . . . . . . . . . . . . . . . . . . . . .
6008-SI IBM PC I/O Scanner . . . . . . . . . . . . . . . . . . . . . . . .
6008-SV VME I/O Scanner . . . . . . . . . . . . . . . . . . . . . . . . . .
6008-SQ DEC Q-BUS I/O Scanner . . . . . . . . . . . . . . . . . . . .
DH+ Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logix55xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLC-5/10, 5/11, 5/15, 5/20, 5/25, 5/30, 5/40, 5/60, 5/80, 5/40L,
5/60L, 5/80L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SLC-5/04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLC2/PLC3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ControlNet Communications . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logix55xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLC-5/20C, 5/40C, 5/60C, 5/80C . . . . . . . . . . . . . . . . . . . . .
PLC-5/20C15, 5/40C15, 5/60C15, 5/80C15 . . . . . . . . . . . . . .
1–1
1–5
1–6
1–8
1–8
1–8
1–9
1–11
1–11
1–13
1–14
1–14
1–14
1–14
1–14
1–15
1–15
1–15
1–15
1–15
1–16
1–16
1–16
1–16
1–16
1–16
1–16
1–17
1–18
1–18
1–18
Publication 2711E-6.17 – November 1998
toc–ii
Table of Contents
Installing PanelView 1000e
Terminals
Installing PanelView 1200e
Terminals
Publication 2711E-6.17 – November 1998
Chapter 2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PanelView 1000e Terminal Dimensions . . . . . . . . . . . . . . . . . . . . .
Tools for Installing Your PanelView 1000e Terminal . . . . . . . . . . . . .
Mounting Options for PanelView 1000e Terminals . . . . . . . . . . . . .
Mounting a Clip-Mount Touch Screen Terminal in a Panel or
Wall Cutout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting a Clip-Mount Keypad Terminal in a Panel or Wall Cutout
Mounting a Touch Screen Terminal in a 19-inch Rack . . . . . . . . .
Mounting a Keypad Terminal in a 19-inch Rack . . . . . . . . . . . . .
Setting Up the PanelView 1000e Terminal . . . . . . . . . . . . . . . . . . .
Switching Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backlight Intensity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Power to the Terminal . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Upload/Download Cable . . . . . . . . . . . . . . . . . .
Connecting the Serial Printer . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Dataliner . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting an External Alarm Relay . . . . . . . . . . . . . . . . . . . . .
Connecting a Terminal to Your PLC System . . . . . . . . . . . . . . . .
Using the PCMCIA Card Slots . . . . . . . . . . . . . . . . . . . . . . . . .
Using a Keyboard or Bar Code Reader . . . . . . . . . . . . . . . . . . .
2–1
2–3
2–5
2–5
2–5
2–8
2–10
2–10
2–11
2–11
2–11
2–11
2–12
2–13
2–13
2–14
2–15
2–17
2–17
Chapter 3
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1
PanelView 1200e Terminal Dimensions . . . . . . . . . . . . . . . . . . . . .
3–3
Tools for Installing Your PanelView 1200e Terminal . . . . . . . . . . . . .
3–5
Mounting Options for PanelView 1200e Terminals . . . . . . . . . . . . .
3–5
Mounting a Stud-Mount Keypad or Touch Screen Terminal in a Panel
or Wall Cutout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–6
Mounting a Clip-Mount Touch Terminal in a Panel or Wall Cutout .
3–8
Mounting a Stud-Mount Keypad Terminal in a 19-inch Rack . . . . . 3–10
Mounting a Touch Screen Terminal in a 19-inch Rack . . . . . . . . . 3–10
Setting Up the PanelView 1200e Terminal . . . . . . . . . . . . . . . . . . . 3–10
Adjusting Contrast and Brightness . . . . . . . . . . . . . . . . . . . . . . . 3–10
Switching Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–11
Connecting Power to the Terminal . . . . . . . . . . . . . . . . . . . . . . . 3–11
Connecting the Upload/Download Cable . . . . . . . . . . . . . . . . . . 3–12
Connecting the Serial Printer . . . . . . . . . . . . . . . . . . . . . . . . . . 3–13
Connecting the Dataliner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–14
Connecting an External Alarm Relay . . . . . . . . . . . . . . . . . . . . . 3–14
Connecting a Terminal to Your PLC System . . . . . . . . . . . . . . . . 3–15
Using the PCMCIA Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . 3–17
Table of Contents
Installing PanelView 1400e
Terminals
Chapter 4
Configuring PanelView
Terminals
Chapter 5
toc–iii
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4–1
PanelView 1400e Terminal Dimensions . . . . . . . . . . . . . . . . . . . . .
4–3
Tools for Installing Your PanelView 1400e Terminal . . . . . . . . . . . . .
4–5
Mounting Options for PanelView 1400e Terminals . . . . . . . . . . . . .
4–5
Mounting a Stud-Mount Keypad or Touch Screen Terminal in a Panel
or Wall Cutout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4–6
Mounting Your PanelView 1400e Terminal in a 19-inch Rack . . . .
4–7
Mounting Your Keypad Terminal in a T30 Cutout . . . . . . . . . . . . .
4–8
Setting Up the PanelView 1400e Terminal . . . . . . . . . . . . . . . . . . .
4–8
Adjusting Contrast and Brightness . . . . . . . . . . . . . . . . . . . . . . .
4–8
Adjusting Horizontal and Vertical Position . . . . . . . . . . . . . . . . .
4–9
Switching Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4–9
Connecting Power to the Terminal . . . . . . . . . . . . . . . . . . . . . . .
4–9
Connecting the Upload/Download Cable . . . . . . . . . . . . . . . . . . 4–11
Connecting the Serial Printer . . . . . . . . . . . . . . . . . . . . . . . . . . 4–11
Connecting the Dataliner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–12
Connecting an External Alarm Relay . . . . . . . . . . . . . . . . . . . . . 4–12
Connecting a Terminal to Your PLC System . . . . . . . . . . . . . . . . 4–13
Using a Keyboard or Bar Code Reader . . . . . . . . . . . . . . . . . . . 4–15
Power-Up Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power On Self-Test (POST) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Integrity Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Failure Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting the Terminal in Configuration Mode . . . . . . . . . . . . . . . . . .
The Configuration Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transferring Application Files . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Application File Transfers . . . . . . . . . . . . . . . . . . . . . . . .
Summary of Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Card Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Formatting the PCMCIA Card or the Onboard Flash Memory (F5)
Erasing a Destination Partition (F4) . . . . . . . . . . . . . . . . . . . . . .
Pass-Through Application File Transfers . . . . . . . . . . . . . . . . . .
PLC Controllers Required for Pass-Through . . . . . . . . . . . . . . . .
DH+ Direct/ControlNet Direct . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting an Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Network Setup for Remote I/O Applications . . . . . . . . . . .
Terminal Network Setup for DH+ Applications . . . . . . . . . . . . . . . .
Terminal Network Setup for ControlNet Applications . . . . . . . . . . . .
Application Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5–1
5–1
5–1
5–2
5–2
5–2
5–3
5–4
5–5
5–5
5–9
5–11
5–12
5–13
5–15
5–16
5–19
5–21
5–23
5–24
5–26
Publication 2711E-6.17 – November 1998
toc–iv
Table of Contents
Application Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Button Audio, Alarm Audio, Audio Volume . . . . . . . . . . . . . . . . .
Alarm Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stuck Cell Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen Saver Display Intensity (1000e only) . . . . . . . . . . . . . . .
Screen Saver Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Display Intensity (1000e only) . . . . . . . . . . . . . . . . . . .
Aligning the 1200e Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aligning on a Keypad Terminal . . . . . . . . . . . . . . . . . . . . . . . . .
Aligning on a Touch Screen Terminal . . . . . . . . . . . . . . . . . . . . .
Printing and Displaying Alarm Messages . . . . . . . . . . . . . . . . . . . .
Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Print Priorities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing Screens from the Terminal . . . . . . . . . . . . . . . . . . . .
Formatting Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printer Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying Alarm Messages . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performing Terminal Diagnostics . . . . . . . . . . . . . . . . . . . . . . . .
Hours Logged . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restoring Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upgrading Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Major Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minor Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mistakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Verifying PanelView Terminal
Operation
Publication 2711E-6.17 – November 1998
5–27
5–28
5–29
5–30
5–33
5–35
5–35
5–38
5–39
5–40
5–41
5–41
5–42
5–42
5–43
5–43
5–46
5–46
5–46
5–46
5–47
5–50
5–50
5–52
5–54
5–55
5–57
5–58
5–58
5–59
5–59
5–60
5–60
Chapter 6
Testing the PanelView Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . .
Downloading the Application File . . . . . . . . . . . . . . . . . . . . . . . . . .
Matching Communications Settings . . . . . . . . . . . . . . . . . . . . . .
Download Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Running the Application File . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the PLC Controller . . . . . . . . . . . . . . . . . . . . . . . . . . .
Testing Retentive Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Testing the Whole System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6–1
6–2
6–2
6–2
6–3
6–3
6–4
6–4
Table of Contents
Maintaining PanelView
Terminals
Chapter 7
Troubleshooting PanelView
Terminals
Chapter 8
Specifications: 1000e
Operator Terminal
Appendix A
Maintaining Your PanelView Operator Terminal . . . . . . . . . . . . . . .
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CRT Intensity (1200e and 1400e) . . . . . . . . . . . . . . . . . . . . .
Changing the Fan Filter (1200e and 1400e) . . . . . . . . . . . . . . . .
Degaussing the CRT (1200e and 1400e) . . . . . . . . . . . . . . . . . .
Avoiding Strong Magnetic Fields (1200e and 1400e) . . . . . . . . . .
Backlight Replacement (1000e) . . . . . . . . . . . . . . . . . . . . . . . .
Verifying Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . .
Major Fault Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minor Fault Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mistake Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLC Communication Problems: Remote I/O . . . . . . . . . . . . . . . . . .
PLC Communication Problems: Data Highway Plus . . . . . . . . . . . .
PLC Communication Problems: ControlNet . . . . . . . . . . . . . . . . . .
Product List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Approvals and Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Standards Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . .
EMC Standards Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
European Union Directive Compliance . . . . . . . . . . . . . . . . . . . . . .
EMC Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Voltage Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intended Use of Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keypad Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touch Screen Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touch Cell Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flat Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backlight Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Color Unit Display Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Highway Plus Communications . . . . . . . . . . . . . . . . . . . . . . .
ControlNet Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLC Remote I/O Communications . . . . . . . . . . . . . . . . . . . . . . . . .
toc–v
7–1
7–1
7–1
7–1
7–1
7–1
7–2
7–2
7–2
7–3
8–1
8–1
8–3
8–4
8–6
8–7
8–8
8–9
A–1
A–1
A–1
A–1
A–1
A–2
A–2
A–2
A–2
A–3
A–3
A–3
A–3
A–4
A–4
A–4
A–4
A–5
A–5
A–5
A–5
Publication 2711E-6.17 – November 1998
toc–vi
Table of Contents
Serial Communications Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard and Bar Code Reader Support . . . . . . . . . . . . . . . . . . . .
PCMCIA Memory Card Support . . . . . . . . . . . . . . . . . . . . . . . . . .
AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time and Date Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature, Humidity, and Altitude . . . . . . . . . . . . . . . . . . . . . . .
Ambient Operating Temperature Limits . . . . . . . . . . . . . . . . . . .
Storage Temperature Limits . . . . . . . . . . . . . . . . . . . . . . . . . . .
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shock and Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shock Amplitudes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vibration Amplitudes for Operating Units . . . . . . . . . . . . . . . . . .
Specifications: 1200e
Operator Terminal
Publication 2711E-6.17 – November 1998
A–6
A–7
A–7
A–7
A–8
A–8
A–8
A–8
A–8
A–9
A–9
A–9
A–9
A–9
A–9
A–9
A–10
A–10
A–10
Appendix B
Product List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Approvals and Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Standards Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . .
EMC Standards Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keypad Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touch Screen Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keypad Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stainless Steel Keypad Terminals . . . . . . . . . . . . . . . . . . . . . . .
Touch Screen Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touch Cell Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CRT Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Color Unit Display Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . .
Degauss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Highway Plus Communications . . . . . . . . . . . . . . . . . . . . . . .
PLC Remote I/O Communications . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Communications Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCMCIA Memory Card Support . . . . . . . . . . . . . . . . . . . . . . . . . .
AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B–1
B–1
B–1
B–1
B–1
B–1
B–1
B–2
B–2
B–2
B–2
B–3
B–3
B–3
B–3
B–4
B–4
B–4
B–5
B–5
B–6
B–6
B–6
B–6
Table of Contents
Alarm Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time and Date Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature, Humidity, and Altitude . . . . . . . . . . . . . . . . . . . . . . .
Ambient Operating Temperature Limits . . . . . . . . . . . . . . . . . . .
Storage Temperature Limits . . . . . . . . . . . . . . . . . . . . . . . . . . .
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Color Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shock and Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shock Amplitudes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vibration Amplitudes for Operating Units . . . . . . . . . . . . . . . . . .
Vibration Amplitudes for Non-Operating Units . . . . . . . . . . . . . . .
Specifications: 1400e
Operator Terminal
toc–vii
B–7
B–7
B–7
B–8
B–8
B–8
B–8
B–8
B–8
B–8
B–9
B–9
B–9
B–9
Appendix C
Product List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Approvals and Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Standards Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . .
EMC Standards Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
European Union Directive Compliance . . . . . . . . . . . . . . . . . . . . . .
EMC Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Voltage Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intended Use of Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keypad Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touch Screen Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touch Cell Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CRT Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Color Unit Display Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . .
Degauss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Highway Plus Communications . . . . . . . . . . . . . . . . . . . . . . .
ControlNet Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLC Remote I/O Communications . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Communications Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCMCIA Memory Card Support . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard and Bar Code Reader Support . . . . . . . . . . . . . . . . . . . .
AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C–1
C–1
C–1
C–1
C–1
C–2
C–2
C–2
C–2
C–3
C–3
C–3
C–3
C–4
C–4
C–4
C–4
C–4
C–5
C–5
C–5
C–6
C–6
C–7
C–7
C–7
C–8
C–8
C–8
Publication 2711E-6.17 – November 1998
toc–viii
Table of Contents
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time and Date Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature, Humidity, and Altitude . . . . . . . . . . . . . . . . . . . . . . .
Ambient Operating Temperature Limits . . . . . . . . . . . . . . . . . . .
Storage Temperature Limits . . . . . . . . . . . . . . . . . . . . . . . . . . .
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Color Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shock and Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shock Amplitudes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vibration Amplitudes for Operating Units . . . . . . . . . . . . . . . . . .
Vibration Amplitudes for Non-Operating Units . . . . . . . . . . . . . . .
Installing the PanelView
Serial Firmware Upgrade
Utility
Appendix D
Installing SFU32 from CD-ROM on Windows NT or Windows 95 . . .
Installing SFU from CD-ROM on Windows 95 or Windows 3.x . . . . .
Installing SFU32 from Floppy Disks on Windows NT or Windows 95
Installing SFU from Floppy Disks on Windows 95 or Windows 3.x . .
Installing Additional Communication Drivers . . . . . . . . . . . . . . . . . .
Starting the PanelView Serial Firmware Upgrade Utility . . . . . . . . . .
Performing a Serial Firmware Upgrade . . . . . . . . . . . . . . . . . . . . .
Exiting from the PanelView Serial Firmware Upgrade Utility . . . . . . .
Index
Publication 2711E-6.17 – November 1998
C–8
C–9
C–9
C–9
C–9
C–9
C–9
C–10
C–10
C–10
C–10
C–10
C–10
D–1
D–2
D–4
D–5
D–6
D–7
D–7
D–8
About This Manual
This manual describes the PanelView 1000e, 1200e, and 1400e
operator terminals and includes information about the following:
• installing your PanelView terminal
• configuring your PanelView terminal
• verifying or testing your PanelView terminal
• maintaining your PanelView terminal
• troubleshooting your PanelView terminal
"
Note: This manual also applies to the enhanced PanelView 1200
Series F and higher terminals running PanelView 1400e firmware.
Chapter 1, Introducing the PanelView Terminals, provides an
overview of the PanelView 1000e, 1200e, and 1400e terminal family,
summarizes new features, and lists applicable PLCs and connections.
Chapters 2, 3, and 4, Installing PanelView 1000e/1200e/1400e
Terminals, provide installation instructions, equipment dimensions,
and mounting options for each model.
Chapter 5, Configuring PanelView Terminals, describes the power-up
tests and how to configure your terminal.
Chapter 6, Verifying PanelView Terminal Operation, describes how
to verify the terminal is communicating correctly, explains the
download procedure for the demo package, and describes testing
retentive objects and the overall system.
Chapter 7, Maintaining PanelView Terminals, provides maintenance
instructions to ensure the longevity and top performance of your
terminal.
Chapter 8, Troubleshooting PanelView Terminals, lists the fault and
error messages that could occur in Configure or Run mode and
provides information to solve problems quickly.
Appendix A contains the Specifications for the PanelView 1000e
terminal.
Appendix B contains the Specifications for the PanelView 1200e
terminal.
Appendix C contains the Specifications for the PanelView 1400e
terminal.
Publication 2711E-6.17 – November 1998
P–2
Preface
Appendix D, Installing the PanelView Serial Firmware Upgrade
Utility, describes how to install the Serial Firmware Upgrade Utility
from CD-ROM or floppy disks.
Intended Audience
This manual is to be used by:
• System Integrators
• Mechanical Installers
• Field Service Personnel
• End Users
Related Publications
The following related publications provide information on
programmable controllers and I/O scanners. To identify the manuals
that refer to these programmable controllers, consult the
Allen-Bradley Publication Index, Publication SD499.
Publication 2711E-6.17 – November 1998
I/O Scanner Publications
Pub. No.
1772-SD/SD2 Remote I/O Scanner/Distribution Panel
1772-2.18
1775-S4A I/O Scanner-Programmer Interface Module User’s Manual
1775-6.5.1
1775-S5, 1775-SR5 I/O Scanner-Communication Adapter Module User’s
Manual
1775-6.5.5
5150-RS PI Start-up and Integration Manual
5000-6.5.1
6008-SI IBM PC I/O Scanner User’s Manual
6008-6.5.3
6008-SV VME I/O Scanner User’s Manual
6008-6.5.2
6008-SQ Q-Bus I/O Scanner Utility Software User’s Manual
6008-6.4.1
1771-SN Sub I/O Scanner Module Data Sheet
1771-2.91
1747-SN RIO Scanner User’s Manual
1747-NM005
Programmable Controller Publications
Pub. No.
1772-LP2 PLC-2/20 Controller Programming and Operations Manual
1772-6.8.1
1772-LP3 PLC-2/30 Controller Programming and Operations Manual
1772-6.8.3
PLC-3 Family Controller Programming Reference Manual
1775-6.4.1
PLC-5 Family Programmable Controllers Hardware Installation Manual
1785-6.6.1
PLC-5 Programming Software
6200-6.4.7
ControlNet PLC-5 Programmable Controllers
1785-6.5.14
5250-LP1, LP2 PLC-5/250 Programming Manual
5000-6.4.8
SLC 500 Family of Programmable Controllers Advanced Programming
Software User’s Manual
1747-NM002
Logix 5550 Controller User Manual
1756-6.5.12
Preface
Technical Support
Services
P–3
If you have questions about PanelView terminals, consult the user
documentation first. If you can’t find the answer, take advantage of our
Technical Support Fax Back system, available 24 hours a day, 7 days a
week at 1-440-646-6701. Or, you can browse through our technical
support document library on the World Wide Web at
http://www.ab.com/mem/technotes/kbhome.html.
Alternatively, contact:
Allen-Bradley
Technical Support
1 Allen Bradley Drive
Mayfield Heights, Ohio 44124-6118
or call 1-440-646-6800 or fax 1-440-646-7801 for technical support
between the hours of 8 AM and 5 PM (EST), Monday to Friday.
The catalog number, series, revision letter, and firmware revision are
on the label on the back of the terminal. Have this information ready
when you call for technical support.
Publication 2711E-6.17 – November 1998
Introducing the PanelView
Terminals
This chapter provides an overview of the PanelView 1000e, 1200e,
and 1400e operator terminals. It describes:
• types and features of the PanelView terminals
• new features of the PanelView terminals
• options and accessories
• the supported Allen-Bradley PLC, SLC, Logix controllers, and
Remote I/O scanners for Remote I/O, Data Highway Plus (DH+)
and ControlNet communications
Welcome to the PanelView
Family
PanelView 1000e, 1200e, and 1400e terminals are the latest
generation of PanelView terminals. Like the PanelView 1200
terminals, PanelView 1000e, 1200e, and 1400e terminals provide a
fast, easy, flexible, and low-cost operator interface for a PLC system.
They are ideal replacements for traditional control panels.
PanelView 1000e, 1200e, and 1400e terminals are pre-assembled and
ready to install in a control panel cutout or 19-inch rack with the
adapter kit. They connect directly to any Allen-Bradley Remote I/O,
Data Highway Plus (DH+), or optionally, ControlNet link.
An Allen-Bradley, IBM PC, or compatible computer (the
development computer) is used to create terminal screens and
functions. Refer to the PanelBuilder 1400e Configuration Software
for Windows User Manual for complete information.
Table 1.A lists the PanelView 1000e, 1200e, and 1400e terminal line
and the accompanying software. Note that Series F and above
PanelView 1200 terminals can be enhanced to PanelView 1200e
functionality. Unless otherwise indicated, replacement kits and
accessories can be used for PanelView 1000e, 1200, 1200e, and
1400e terminals.
Publication 2711E-6.17 – November 1998
1–2
Introducing the PanelView Terminals
Table 1.A PanelView Terminal Products and Catalog Numbers
Catalog Number
Product
Description
2711E-T10C6
1000e Touch Screen
Terminal
Color display, clip mount, NEMA 4X
2711E-K10C6
1000e Keypad Terminal
Color display, clip mount, NEMA 4X
2711E-T10C7
1000e Touch Screen
Terminal
ControlNet-enhanced release 1.25 2711E-T10C6 terminal
2711E-K10C7
1000e Keypad Terminal
ControlNet-enhanced release 1.25 2711E-K10C6 terminal
2711E-T10C15
1000e Touch Screen
Terminal
ControlNet-enhanced release 1.5 2711E-T10C6 terminal
2711E-K10C15
1000e Keypad Terminal
ControlNet-enhanced release 1.5 2711E-K10C6 terminal
2711E-T12C6
1200e Touch Screen
Terminal
Color display, clip mount, NEMA 12
2711E-T12C4
1200e Touch Screen
Terminal
Color display, stud mount, NEMA 4X (Indoor use only)
2711E-K12C6
1200e Keypad Terminal
Color display, stud mount, NEMA 4X (Indoor use only)
2711E-K12C6L2
1200e Keypad Stainless
Steel Terminal
Color display, stud mount, stainless steel bezel, NEMA 4X (Indoor use only)
2711E-T14C6
1400e Touch Screen
Terminal
Color display, stud mount, NEMA 4X (Indoor use only)
2711E-K14C6
1400e Keypad Terminal
Color display, stud mount, NEMA 4X (Indoor use only)
2711E-T14C7
1400e Touch Screen
Terminal
ControlNet-enhanced release 1.25 2711E-T14C6 terminal
2711E-K14C7
1400e Keypad Terminal
ControlNet-enhanced release 1.25 2711E-K14C6 terminal
2711E-T14C15
1400e Touch Screen
Terminal
ControlNet-enhanced release 1.5 2711E-T14C6 terminal
2711E-K14C15
1400e Keypad Terminal
ControlNet-enhanced release 1.5 2711E-K14C6 terminal
2711E-ND1
PanelBuilder 1400e
Configuration Software for
Windows
Includes PanelBuilder 1400e software, manuals
2711E-ND1DE
PanelBuilder 1400e
Configuration Software for
Windows – German Version
Includes PanelBuilder 1400e software, manuals
2711E-ND1FR
PanelBuilder 1400e
Configuration Software for
Windows – French Version
Includes PanelBuilder 1400e software, manuals
2711E-ND1ES
PanelBuilder 1400e
Configuration Software for
Windows – Spanish Version
Includes PanelBuilder 1400e software, manuals
2711E-ND7
File Transfer Utility for
Windows – English Version
Standalone File Transfer Utility for all PanelView enhanced terminals and PanelView 1200
terminals, which require less hard disk space than the PanelBuilder 1400e Configuration
Software kits.
Note: This File Transfer Utility is included in all PanelBuilder 1400e Configuration Software
kits.
Publication 2711E-6.17 – November 1998
Introducing the PanelView Terminals
1–3
Table 1.B PanelView Terminals Accessories
Catalog Number
Product
Description
2711-NC1
Upload/Download Cable
For 1200e/1400e terminals only. Includes a 9-pin or 25-pin RS-232 serial cable
(Upload/Download cable) to transfer files between terminal and development computer. The
cable is 10 ft (3 m) long.
2711-NC13
Upload/Download Cable
For 1000/1000e terminals only. Includes a 9-pin RS-232 serial cable (Upload/Download
cable) to transfer files between terminal and development computer. The cable is 16.4 ft (5 m)
long.
2711-NC14
Upload/Download Cable
For 1000/1000e terminals only. Includes a 9-pin RS-232 serial cable (Upload/Download
cable) to transfer files between terminal and development computer. The cable is 32.7 ft
(10 m) long.
2706-NC13
Upload/Download Cable
For 1000/1000e terminals only. Includes a 9-pin RS-232 serial cable (Upload/Download
cable) to transfer files between terminal and development computer. The cable is 10 ft (3 m)
long.
2711-NC2
Remote Keyswitch and
RS-232 Port Assembly
For 1200/1200e/1400e terminals only. Includes RS-232 port assembly and remote
keyswitch. Allows remote mode selection and serial port access.
2711E-NC1
Remote RS-232 Serial Port
Assembly
For 1000e terminals only. Includes a 9-pin RS-232 port assembly to allow serial port
access.
2711-NM11
256K PCMCIA Installation
Kit
Includes blank 256K PCMCIA memory card for application file storage, and instruction
sheet.
2711-NM12
1-MB PCMCIA Memory
Card for Application
Expansion
Includes blank 1-MB PCMCIA memory card for application file storage, and instruction
sheet.
2711-NM13
2-MB PCMCIA Memory
Card for Application
Expansion
Includes blank 2-MB PCMCIA card for application file storage, and instruction sheet.
2711-NM14
4-MB PCMCIA Memory
Card for Application
Expansion
Includes blank 4-MB PCMCIA card for application file storage, and instruction sheet.
2711-NM15
8-MB PCMCIA Memory
Card for Application
Expansion
Includes blank 8-MB PCMCIA card for application file storage, and instruction sheet.
2711-NV1
Anti-Glare Overlay for
terminals
Includes 5 anti-glare protective overlays for your 1200 and 1200e terminal screens.
2711-NR5T
Adapter for PanelView
1000/1000e Touch Screen
Terminals
Includes an adapter for PanelView 1000/1000e Touch Screen terminals to mount in
PanelView 1200 Touch Screen terminal panel cutouts.
2711-NR5K
Adapter for PanelView
1000/1000e Keypad
Terminals
Includes an adapter for PanelView 1000/1000e Keypad terminals to mount in PanelView
1200 Keypad terminal panel cutouts.
2711-NR6T
19-in. Rack Mount Kit for
PanelView 1000/1000e
Touch Screen Terminals
Includes a 19-inch rack adapter and mounting hardware for 1000/1000e clip-mount touch
screen terminals.
2711-NR6K
19-in. Rack Mount Kit for
PanelView 1000/1000e
Keypad Terminals
Includes a 19-inch rack adapter and mounting hardware for 1000/1000e clip-mount keypad
terminals.
Publication 2711E-6.17 – November 1998
1–4
Introducing the PanelView Terminals
Catalog Number
Product
Description
2711-NR1
19-in. Rack Mount Kit for
PanelView 1200 and 1200e
Touch Screen Terminals
(not for 2711 or 2711E
Keypad Terminals)
Includes a rack adapter and mounting hardware for stud-mount and clip-mount touch
screen terminals.
2711-NR4
19-in. Rack Mount Kit for
PanelView 1400e Touch
Screen Terminals (not for
2711E Keypad Terminals)
Includes a rack adapter and mounting hardware for stud-mount and clip-mount touch
screen terminals.
2711-NV6T
Anti-Glare Overlay for
1000/1000e Touch Screen
Terminals
Includes an anti-glare overlay for PanelView 1000/1000e Touch Screen terminals.
2711-NV6K
Anti-Glare Overlay for
1000/1000e Keypad
Terminals
Includes an anti-glare overlay for PanelView 1000/1000e Keypad terminals.
2711E-NV1
Anti-Glare Overlay for
1400e Touch Screen and
Keypad Terminals
Includes an anti-glare overlay for PanelView 1400e Touch Screen and Keypad terminals.
2711E-U1B12C
PanelView 1200
Enhancement Kit with
preloaded 4-MB PCMCIA
memory card and 2-MB
SIMM
Includes 2-MB SIMM and 4-MB PCMCIA memory card loaded with new version of firmware.
Also includes 3 product identification labels (terminal types).
2711E-NA1
ISA Card Adapter Kit
Includes an ISA card adapter to install a communication card in a PanelView 1400e
Terminal.
2711E-NA2
ISA Card Adapter Kit
Includes an ISA card adapter to install communication cards in a PanelView 1000e
Terminal.
2711E-UMOD
Firmware Enhancement Kit
for Modbus connectivity on
terminals
Includes firmware upgrade for Modbus support on PanelView 1000e/1400e terminals.
Note: For Modbus communications, you need a Modbus ISA/EISA Interface Card and a
2711E-NA1 or 2711E-NA2 Adapter Kit.
2711E-URAM1
System Memory Upgrade
Kit for PanelView 1000e
Terminals
Includes additional system memory upgrade to support PanelView 1000e features and
functionalities.
2711E-URAM2
System Memory Upgrade
Kit for PanelView 1400e
Terminals
Includes additional system memory upgrade to support PanelView 1400e features and
functionalities.
Table 1.C PanelView Replacement Kits
Publication 2711E-6.17 – November 1998
Catalog Number
Product
2711-NP2
Mounting Clips for PanelView 600/900/1000/1000e Terminals
2711E-NF1
Function Key Legend Strips for PanelView 1000e Keypad
Terminals
6189-NL2
Backlight Replacement Kit for PanelView 1000e and 6189
Industrial Computers
Introducing the PanelView Terminals
Keypad and Touch Screen
Terminals and Software
1–5
Catalog Number
Product
2711E-NK2
Keypad Replacement Kit for PanelView 1200e Terminals
2711E-NK3
Stainless Steel Keypad Replacement Kit for PanelView 1200
(Series D and above) and 1200e Keypad Terminals
2711E-NK5
Keypad Replacement Kit for PanelView 1400e Terminals
2711-NT1
Touch Screen Replacement Kit for PanelView 1200 (Series D,
E, F, and G) and 1200e Terminals
2711E-NT2
Analog Touch Screen Replacement Kit for PanelView 1400e
46715-414-01
Spare Mode Select Keys
46715-416-01
PanelView 1200 and 1200e Touch Screen Mounting hardware
for clip mounting
46715-418-01
Replacement Keyswitch Assembly for PanelView
1200/1200e/1400e Terminals
46715-419-01
Blank keypad legend inserts for PanelView 1200 and
PanelView 1200e Keypad Terminals (note: not for
2711E-K12C6L2)
22112-046-03
Remote I/O connector for PanelView 1000e, 1200, 1200e, and
1400e Terminals
Keypad and touch screen terminals are configured the same with
these exceptions:
• different button setups
• certain screen objects are specific to keypad terminals and others
to touch screen terminals. For information about objects, refer to
the PanelBuilder 1400e Configuration Software for Windows
User Manual or the PanelBuilder 1400e Configuration Software
for Windows Screen Objects Reference Manual.
The PanelView 1000e and 1400e touch screen terminals use analog
resistive touch screens. This allows input objects to be any size
(minimum 40 by 40 pixels) and to be placed anywhere on the screen.
The analog resistive touch screen provides greater flexibility in
screen design compared to PanelView 1200 and 1200e terminals.
PanelView 1200 and 1200e terminals use a touch matrix, which
requires that all input objects align with a touch grid.
!
ATTENTION: In the unlikely event that two or more
touches occur simultaneously in the same horizontal or
vertical line, an input object located half-way between
the two touches could be activated. This is inherent in
the analog resistive touch screen technology that is
used in PanelView 1000e and 1400e terminals.
Publication 2711E-6.17 – November 1998
1–6
Introducing the PanelView Terminals
Keypad Terminals
The keypad terminal has:
• 21 user-definable function keys
• a keypad for entering numeric values
• up, down, left, and right arrow keys
• Home, Enter, Select, Cancel, Raise, Lower, and Backspace keys
The user-definable function keys on keypad terminals are labeled at
the factory, but you can create key labels (legends) to suit your
application. The replacement key legends slide in from the rear of
the faceplate. The Legend Kit, included with your shipment,
provides blank card material that accepts most types of markers or
paste-on labels.
Figure 1.1 1000e, 1200e, and 1400e Keypad Terminals (Front
View)
Publication 2711E-6.17 – November 1998
Introducing the PanelView Terminals
1–7
Publication 2711E-6.17 – November 1998
1–8
Introducing the PanelView Terminals
Function Keys
When creating screens, you can assign any of the 21 function keys to
objects so they do several tasks, such as turning on PLC input bits or
changing screens. Keys can have different task assignments for each
screen created.
Numeric Keypad
The keypad terminal has a numeric input keypad that includes
number keys, Enter, Backspace, – (negative), and . (decimal) keys.
To make a numeric entry, you call up a pop-up Numeric Entry
Scratchpad that displays the numbers as you type. You can then send
the numeric value to the PLC controller.
Special Keys
The keypad terminal includes special keys:
• the arrow keys and Home are used to navigate through Set Bit
Cursor and Numeric Input Cursor Points, or the ASCII input
object
• Select is used with the Set Bit Cursor and Numeric Input Cursor
Points to pop up the numeric entry scratchpad
• Cancel can be used with all numeric keypads, Set Bit Cursor and
Numeric Input Cursor Points to remove the numeric entry
scratchpad
• Raise and Lower are used with Numeric Input Cursor Point only,
to change the numeric value sent to the PLC
The three blank keys on the bottom right of the 1200e terminals
cannot be configured.
Refer to the PanelBuilder 1400e Configuration Software for
Windows User Manual for details.
Publication 2711E-6.17 – November 1998
Introducing the PanelView Terminals
1–9
Touch Screen Terminals
To operate a touch screen terminal, touch the buttons on the screen.
Figure 1.2 1000e, 1200e, and 1400e Touch Screen Terminals (Front
View)
Publication 2711E-6.17 – November 1998
1–10
Introducing the PanelView Terminals
The 1200e touch screen contains 120 touch cells, laid out in a 10-cell
by 12-cell grid. Each touch cell is 64 pixels wide by 40 pixels high.
For the 1000e and 1400e analog resistive touch screen, the minimum
touch object size is 40 by 40 pixels. There is no touch matrix for the
1000e and 1400e touch screens so the objects can be placed at any
location. In PanelBuilder, a grid can be made visible to allow you to
align screen objects.
Touch cells are grouped to create different types and sizes of buttons.
You can activate input functions by touching the appropriate object
on the terminal and can configure the terminal to beep when a touch
cell is pressed.
The PanelView 1000e and 1400e Touch Screen terminals use analog
resistive touch screens. This allows input objects to be any size
(minimum 40 by 40 pixels) and to be placed anywhere on the screen.
The analog resistive touch screen provides greater flexibility in
screen design compared to PanelView 1200 and 1200e terminals.
PanelView 1200 and 1200e terminals use a touch matrix, which
requires that all input objects align with a touch grid.
Publication 2711E-6.17 – November 1998
Introducing the PanelView Terminals
!
1–11
ATTENTION: In the unlikely event that two or more
touches occur simultaneously in the same horizontal or
vertical line, an input object located half-way between
the two touches could be activated. This is inherent in
the analog resistive touch screen technology that is
used in PanelView 1000e and 1400e terminals.
PanelBuilder 1400e Configuration Software
PanelBuilder 1400e Configuration Software for Windows is an
easy-to-learn tool for developing complex applications quickly and
efficiently. You run PanelBuilder 1400e Configuration Software on a
personal computer to develop operator interface applications for
PanelView 1000e, 1200e, or 1400e operator terminals.
The Windows platform offers many advantages. In addition to a
superior graphical interface, you can work in several applications at
once and transfer information between them easily.
Features of the PanelView
Terminals
Figures 1.1 and 1.2 show the front view of the PanelView 1000e,
1200e, and 1400e terminals. The back of each terminal is shown in
the installation chapter for each terminal type.
The PanelView 1000e, 1200e, and 1400e terminals differ from the
PanelView 1200 terminal as follows:
• Remote I/O, DH+, and ControlNet connectivity is available (used
one at a time).
• The PanelView 1000e terminal is available in four models:
– color touch screen clip mount (2711E-T10C6)
– color keypad clip mount (2711E-K10C6)
– color touch screen clip mount with ControlNet support
(2711E-T10C7, 2711E-T10C15)
– color keypad clip mount with ControlNet support
(2711E-K10C7, 2711E-K10C15)
Publication 2711E-6.17 – November 1998
1–12
Introducing the PanelView Terminals
• The PanelView 1200e terminal is available in four models:
– color touch screen clip mount (2711E-T12C6)
– color touch screen stud mount (2711E-T12C4)
– color keypad stud mount (2711E-K12C6)
– color keypad stainless steel stud mount (2711E-K12C6L2)
• The 1400e terminal is available in four models:
– color touch screen stud mount (2711E-T14C6)
– color keypad stud mount (2711E-K14C6)
– color touch screen stud mount with ControlNet support
•
•
•
•
•
•
(2711E-T14C7, 2711E-T14C15)
– color keypad stud mount with ControlNet support
(2711E-K14C7, 2711E-K14C15)
The front panels of the PanelView 1000e, 1200e, and 1400e
terminals have new graphics.
The PanelView 1000e and 1400e terminals have analog resistive
touch screens.
The PanelView 1400e terminal has an analog resistive touch
screen with built-in, anti-glare glass.
The PanelView 1000e terminals run only firmware versions 3 and
above. The PanelView 1200e and 1400e terminals run firmware
versions 1 and above. The application you run on PanelView
1000e, 1200e, and 1400e terminals is displayed in a pixel
graphics format, rather than a character-based format.
The logic board for PanelView enhanced terminals has a
communication slot for communication options, such as
ControlNet.
The keyboard port for the PanelView 1000e and 1400e terminals
is supported by the PanelView firmware.
Table 1.D outlines the main changes that have been made to the
memory configuration on the terminal’s logic board.
Publication 2711E-6.17 – November 1998
Introducing the PanelView Terminals
1–13
Table 1.D Memory Configuration on PanelView 1200 (Series
F and above) and PanelView 1000e, 1200e, and 1400e
Operator Terminals
Memory Type
PanelView 1000e Terminal
PanelView 1200 Terminal (Series
F and Above)
PanelView 1200e and 1400e
Terminals
User RAM (SRAM)
(Battery-backed)
128K of battery-backed static RAM
(stores the terminal configuration
parameters, alarm status and
history, retentive data; no application
file storage)
128K (stores the terminal
configuration parameters, alarm
history, and application file)
128K of battery-backed static RAM
(stores the terminal configuration
parameters, alarm status and
history, retentive data; no application
file storage)
Flash
1.75 MB for firmware; 2.25 MB for
application file storage
256K (stores firmware and BIOS);
no flash for application file storage
1.75 MB for firmware; 256K for
application file storage
E/EPROM
N/A
Optional 64K/128K E/EPROM
(provides backup application file
storage)
N/A
PCMCIA memory card
support
Provides application file storage up
to 15.75 MB
1.75 MB for firmware; application file
storage up to 2.25 MB for enhanced
F and above terminals
Provides application file storage up
to 15.75 MB
If you have complex user applications in PanelView terminals and
you use PanelView Version 5 firmware’s new features, we
recommend that you increase the system RAM in the PanelView
terminal. For PanelView 1000e terminals, you can install a 4-MB
RAM DIMM (A-B Catalog Number 2711E-URAM1). For
PanelView 1400e terminals, you can install a 4-MB RAM SIMM
(A-B Catalog Number 2711E-URAM2).
Additional Features of the
PanelView Terminals
PanelView Version 5 firmware provides the following additional
features:
• ControlNet scheduled communications using the 1784-KTCs card
• ControlLogix Legacy mode support
• ControlLogix gateway file transfer and alarm history support
• Enhanced printer support
• Dataliner display device support
• Enhanced alarm features
• Keyboard support for PanelView 1000e and 1400e terminals
• 115.2K and 230.4K baud rate for DH+ communications
Publication 2711E-6.17 – November 1998
1–14
Introducing the PanelView Terminals
Applicable Programmable
Controllers and
Connections
PanelView terminals can be connected to any Allen-Bradley 1771
Remote I/O, Data Highway Plus, or ControlNet link. Applicable host
controllers include almost all Allen-Bradley Programmable Logic
Controllers, as well as certain IBM computers, interface cards, VME
Controllers, and the DEC Q-Bus interface.
Newly-released Allen-Bradley programmable controllers not yet
listed will support PanelView terminals as long as the terminals
support 1771 Remote I/O, DH+, or ControlNet networks.
Remote I/O Communications
The terminal can occupy up to 64 I/O racks in a PLC. It has
the same configurability as—and more than—a standard I/O rack.
Refer to your applicable Allen-Bradley Programmable Controller
and Remote I/O Scanner user’s manuals for connection and Remote
I/O configuration limitations.
The following host controllers can be connected to the terminals over
a Remote I/O link.
Logix55xx
You can connect one or more terminals to a 1756-DHRIO
DH+/Remote I/O Module with other I/O racks.
PLC-5/11, 5/15, 5/20, 5/25, 5/30, 5/40, 5/60, 5/80, and 5/250
Processors
You can connect one or more terminals directly to a PLC-5 Remote
I/O Port (in Scanner Mode) with other I/O racks. If the PLC-5
Remote I/O Port is used in the adapter mode, one or more terminals
can be connected to that PLC-5 along with other I/O racks via a
1771-SN I/O Subscanner Module.
The terminals can communicate at 57.6, 115.2, and 230.4 kilobauds
with any PLC-5 that can support those baud rates.
If you are using a PLC-5/15 with partial rack addressing and block
transfers, you must use PLC-5/15 Series B, revision J or later.
PLC-5/10 Processor
One or more terminals can be connected to this processor with other
I/O racks by a 1771-SN I/O Subscanner Module.
Publication 2711E-6.17 – November 1998
Introducing the PanelView Terminals
1–15
PLC-3 and PLC-3/10 Processors
One or more terminals can be connected directly to a PLC-3 or
PLC-3/10 remote I/O Scanner along with other I/O racks.
If you are using a 1775-S4A Remote Scanner/Distribution panel, you
must use Series B or higher.
PLC-2 Family Processors via 1771-SN or 1772-SD2
The PLC-2 family includes the PLC-2/05, 2/15, 2/20, and 2/30. One
or more terminals can be connected to these processors with other
I/O racks by the 1771-SN I/O Subscanner Module.
If you are using a 1772-SD2 Scanner/Distribution panel, you must
use Revision 3 or later.
SLC-5/02, 5/03, or 5/04 via 1747-SN Series A or B
One or more terminals can be connected to the 1747-SN I/O
Subscanner Modules (SLC-RIO connection) for the SLC processors.
Each module provides an additional remote I/O link for the host
programmable controller. The rack range of the 1747-SN Series A or
B is 0 to 3.
Important:
The 1747-SN Series A supports only discrete data
whereas Series B also provides block transfer support.
Series B also supports Pass-Through communication
capability when used with the 5/04.
1771-SN I/O Subscanner Module
One or more 1771-SN I/O Subscanner Modules can be installed in
any standard Allen-Bradley 1771 I/O rack. Each module provides an
additional Remote I/O link for the host programmable controller.
One or more terminals can be connected to any of the previously
mentioned processors along with other I/O racks via a 1771-SN I/O
Subscanner Module. Refer to the 1771-SN Sub I/O Scanner Module
Data Sheet for details.
6008-SI IBM PC I/O Scanner
This module can be installed in an IBM PC or compatible computer
to provide the computer with an Allen-Bradley 1771 Remote I/O
Link. You can then connect Allen-Bradley Remote I/O racks and
devices such as the PanelView 1000e/1200e/1400e terminal to this
computer.
Publication 2711E-6.17 – November 1998
1–16
Introducing the PanelView Terminals
6008-SV VME I/O Scanner
This module can be installed in a VME backplane, providing the
VME controller with an Allen-Bradley 1771 Remote I/O Link.
Allen-Bradley Remote I/O racks and devices such as the PanelView
1000e/1200e/1400e terminal can then be connected to this VME
controller.
6008-SQ DEC Q-BUS I/O Scanner
This module can be installed in a DEC Q-Bus controller to provide it
with an Allen-Bradley 1771 Remote I/O Link. Allen-Bradley
Remote I/O racks and devices such as the PanelView
1000e/1200e/1400e terminal can then be connected to this controller.
DH+ Communications
The terminal can be connected to a DH+ network directly so the
terminal can communicate with several controllers simultaneously. It
can be connected to the following host controllers over DH+.
Logix55xx
You can connect one or more terminals to a 1756-DHRIO
DH+/Remote I/O Module.
PLC-5/10, 5/11, 5/15, 5/20, 5/25, 5/30, 5/40, 5/60, 5/80, 5/40L,
5/60L, 5/80L
You can connect one or more terminals directly to one of the PLC-5
family of programmable controllers over DH+ so the terminal can
communicate with several controllers simultaneously.
SLC-5/04
You can connect one or more terminals directly to one of the
SLC-5/04 family of programmable controllers over DH+ so the
terminal can communicate with several controllers simultaneously.
PLC2/PLC3
The terminal supports communications to one or more PLC2s or
PLC3s via offlink addressing: the PLC2 also communicates by a
1785-KA module (DH+ to DH bridge), and the PLC3 communicates
by a 1775-KA module.
Publication 2711E-6.17 – November 1998
Introducing the PanelView Terminals
1–17
ControlNet Communications
To communicate on ControlNet, install a ControlNet Communication
Interface Card (A-B Catalog Number 1784-KTCx, Series B or later,
or 1784-KTCs) in your PanelView 1000e or 1400e terminal. These
cards enable the terminal to communicate with devices on the
ControlNet network and also act as an interface between the terminal
and ControlNet for ControlNet-Direct application file transfers.
The 1784-KTCx card allows the PanelView terminal to communicate
in unscheduled mode. The 1784-KTCs card allows the PanelView
terminal to communicate in scheduled and unscheduled modes.
The 1784-KTCx card is installed in PanelView 1000e and 1400e
operator terminals (A-B Catalog Numbers 2711E-K10C7,
2711E-T10C7, 2711E-K14C7, and 2711E-T14C7).
The 1784-KTCs card is installed in PanelView 1000e and 1400e
operator terminals (A-B Catalog Numbers 2711E-K10C15,
2711E-T10C15, 2711E-K14C15, and 2711E-T14C15).
For information about installing communication cards in the
PanelView terminal see the PanelView ISA Card Adapter Installation
Data Sheet, A-B publication 2711E-5.6.
Important:
The DIP switch settings on both the KTCx and KTCs
card must be configured to work with PanelView. If the
settings have been changed and you want to use the
card in the PanelView terminal, you must use the DIP
switches on the KTCx or KTCs card to select the
following addresses:
Address
Setting
Base Memory
D400:0000
Base I/O
220
Figure 1.3 KTCx and KTCs Switch Settings — Base Memory
Address
Base Memory Address D400:0000
up (1)
1 2
1 2 3 4
down (0)
Publication 2711E-6.17 – November 1998
1–18
Introducing the PanelView Terminals
Figure 1.4 KTCx and KTCs Switch Settings — Base I/O
Address
Base I/O Address 220
up (1)
1 2 3 4
down (0)
For more information, see the documentation that comes with the
KTCx or KTCs card.
For more information about communication devices for ControlNet,
see the PanelBuilder 1400e Configuration Software for Windows
User Manual, A-B publication 2711E-819.
When you switch from Configure to Run mode to execute
ControlNet applications, you may notice a delay of 5 to 15 seconds.
During this time, the message “Initializing Communications”
appears on the screen. The delay occurs because the KTCx or KTCs
card has a separate processor that takes 5 to 15 seconds to
synchronize with ControlNet. When you switch to Run mode the
application screen will appear after approximately 5 seconds. Then
the message “Communication Lost” will appear for approximately
10 seconds, while the connection is established.
The following host controllers can be connected to the terminals over
ControlNet.
Logix55xx
You can connect one or more terminals to a 1756-CNET ControlNet
Communications Module.
PLC-5/20C, 5/40C, 5/60C, 5/80C
You can connect the PanelView terminal to the PLC-5C enhanced
family of programmable controllers over ControlNet release 1.25.
PLC-5/20C15, 5/40C15, 5/60C15, 5/80C15
You can connect the PanelView terminal to the PLC-5C15 enhanced
family of programmable controllers over ControlNet release 1.5.
Publication 2711E-6.17 – November 1998
Installing PanelView 1000e
Terminals
Overview
This chapter explains how to install a PanelView 1000e terminal.
Specifically, it provides:
• terminal dimensions
• a list of tools for installing the terminal
• cutout dimensions for panel mounting
• information about mounting options
This chapter also provides information about the correct use of the
following hardware features, specifically:
• how to switch modes
• how to connect power to the terminal
• how to connect the Upload/Download cable
• how to connect a serial printer
• how to connect an external alarm relay
• how to connect a terminal to your PLC system
• how to use the PCMCIA cards
• how to connect a keyboard and/or a bar code reader
Figure 2.1 shows the rear and bottom panel of the PanelView 1000e
terminal. Note the location of the power connector, alarm relay
connector, keyboard port, RS-232 port, and Remote I/O DH+
connector.
Publication 2711E-6.17 – November 1998
2–2
Installing PanelView 1000e Terminals
Figure 2.1 Rear and Bottom View of PanelView 1000e
Terminal
Publication 2711E-6.17 – November 1998
Installing PanelView 1000e Terminals
PanelView 1000e Terminal
Dimensions
Figure 2.2 shows the dimensions of the keypad terminals.
Figure 2.2 PanelView 1000e Keypad Terminal Dimensions
1.06”
(27 mm)
0.69”
(18 mm)
11.12”
(282 mm)
0.94”
(24 mm)
Clip Slot
3.2”
(81 mm)
4.45”
(113 mm)
0.69”
(18 mm)
0.15”
(3.81 mm)
0.69”
(18 mm)
1.2”
(30.4 mm)
2–3
1.37”
(35 mm)
6.15”
(156 mm)
5.43”
(138 mm)
3.64”
(92 mm)
1.46”
(37 mm)
0.95”
(24 mm)
PanelView 1000e
Allen–Bradley
4.48”
(114 mm)
0.53”
(13 mm)
6.8”
(173 mm)
F17
F18
10.03”
8.43”
(255 mm) (224 mm)
F19
7
4
1
.
8
5
2
0
9
6
3
–
F20
11.11”
(282 mm)
F21
Home
4.48”
(114 mm)
F1
F2
F3
F4
F5
F6
F7
F8
F9 F10
F9
F10 F11
F11 F12
F12 F13
F13 F14
F14 F15
F15 F16
F16
0.9”
(23 mm)
0.55”
(14 mm)
6.15”
(156 mm)
0.65”
(17 mm)
Raise
SELECT
Lower
CANCEL
16.64”
(423 mm)
24751
Publication 2711E-6.17 – November 1998
2–4
Installing PanelView 1000e Terminals
Figure 2.3 shows the dimensions of the touch screen terminals.
Figure 2.3 PanelView 1000e Touch Screen Terminal
Dimensions
0.69”
(18 mm)
11.12”
(282 mm)
0.94”
(24 mm)
Clip Slot
1.06”
(27 mm)
0.7”
(18 mm)
0.15”
(3.81 mm)
1.2”
(30 mm)
4.45”
(113 mm)
0.69”
(18 mm)
1.37”
(35 mm)
3.64”
(92 mm)
4.17”
0.85”
(106 mm) (22 mm)
1.2”
(30 mm)
6.83”
(174 mm)
0.96”
(24 mm)
0.5”
(13 mm)
PanelView 1000e
Allen–Bradley
4.48”
(114 mm)
11.11”
(282 mm)
10.03” 8.43”
(255 mm) (224 mm)
4.48”
(114 mm)
0.55”
(14 mm)
0.9”
(23 mm)
6.18”
(157 mm)
0.65”
(17 mm)
14.58”
(370 mm)
3.75”
(95mm)
Allow 3.75” at this side
internally so that unit can
be opened for replacing
the backlight module.
24752
Publication 2711E-6.17 – November 1998
Installing PanelView 1000e Terminals
Tools for Installing Your
PanelView 1000e Terminal
"
2–5
You need the following tools to make a wall or panel cutout and
install a PanelView 1000e terminal in it. The terminal shipment
includes a terminal cutout template for your use.
Note: Converted metric values have been rounded off. This applies
to the dimensions specified in the drawings in this chapter.
To make a wall or panel cutout, you need these tools:
• center punch
• scriber
• hammer
• power jig saw
• set of drill bits (1/8 to 3/8 inch)
• metal ruler for drawing lines on the panel
• power drill
• torque wrench
• metal file
To install the terminal, you need this tool:
• slot screwdriver or Phillips screwdriver
Mounting Options for
PanelView 1000e
Terminals
You can mount your PanelView 1000e terminal in a rectangular
cutout in a panel or wall or in a 19-inch rack with the adapter kit.
The terminals are mounted with mounting clips.
"
Note: When choosing a location in which to install the PanelView
terminal, we recommend you provide at least 3.75 inches (9.5 cm)
clearance around the terminal from the panel or rack in which it is
installed, for proper ventilation.
Mounting a Clip-Mount Touch Screen Terminal in a Panel or Wall
Cutout
To prepare the location:
1. Make the appropriate cutout in the wall or panel location.
Figure 2.4 shows the cutout dimensions for the clip-mount
terminal.
2. Insert the terminal into the panel or wall cutout.
Publication 2711E-6.17 – November 1998
2–6
Installing PanelView 1000e Terminals
Figure 2.4 Clip-Mount Touch Screen Terminal Panel
Cutout
Bezel Border Line
CL
10.11” 11.11”
(257 mm) (282 mm)
CL
CUTOUT
13.29”
(338 mm)
14.58”
(370 mm)
24756
Eight assembled mounting clips are provided with the clip-mount
touch screen terminals; only six clips are used for the mount.
To install the clips:
1. Make sure the gasket is installed. If not, the terminal’s NEMA 4X
seal will not be met.
2. Install the six mounting clips (2 on top, 2 on bottom, 1 on each
side). The ends of the clips slide into the slots on the terminal.
3. Tighten the mounting clip screws by hand until the gasket seal
contacts the mounting surface uniformly. See Figures 2.5 and 2.6
for details.
Publication 2711E-6.17 – November 1998
Installing PanelView 1000e Terminals
2–7
Figure 2.5 Touch Screen Clip Mount (Side View)
Gasket
Screwdriver Slot
Rack Mount Adapter
or User Panel
Mounting
Mounting Slot Clip
Upper Right Side
Touch Screen
Terminal Front Bezel
Front Bezel
24772
Figure 2.6 Touch Screen Clip Mount (Back View)
Mounting Slot
Foot Pad
Screwdriver Slot
Panel Mount Screw
Mounting Clip
24780
Publication 2711E-6.17 – November 1998
2–8
Installing PanelView 1000e Terminals
4. Tighten the mounting clip screws to a torque of 10 inch-pounds. Do
not over-tighten.
!
ATTENTION: Tighten mounting clips to a torque of
10 inch-pounds to provide a proper seal and to prevent
potential damage to the terminal. Allen-Bradley
assumes no responsibility for water or chemical
damage to the terminal or other equipment within the
enclosure because of improper installation.
5. Remove the protective installation label covering the top vents of
the terminal.
!
ATTENTION: Remove the protective installation
label covering the top vents to prevent overheating and
damage to the terminal.
Mounting a Clip-Mount Keypad Terminal in a Panel or Wall
Cutout
To prepare the location:
1. Make the appropriate cutout in the wall or panel location. Figure 2.7
shows the cutout dimensions for the clip-mount terminal.
2. Insert the terminal into the panel or wall cutout.
Figure 2.7 Clip-Mount Keypad Terminal Panel Cutout
Bezel Border Line
CL
10.11” 11.11”
(257 mm) (282 mm)
CL
CUTOUT
15.35”
(390 mm)
16.64”
(423 mm)
24755
Eight assembled mounting clips are provided with the clip-mount
keypad terminals; only six clips are used for the mount.
3. Make sure the gasket is installed. If not, the terminal’s NEMA 4X
seal will not be met.
Publication 2711E-6.17 – November 1998
Installing PanelView 1000e Terminals
2–9
To install the clips:
1. Install the six mounting clips (2 on top, 2 on bottom, 1 on each
side). The ends of the clips slide into the slots on the terminal.
2. Tighten the mounting clip screws by hand until the gasket seal
contacts the mounting surface uniformly. See Figures 2.8 and 2.9
for details.
Figure 2.8 Keypad Terminal Clip Mount (Side View)
Gasket
Rack Mount Adapter
or User Panel
Screwdriver Slot
Mounting
Clip
Mounting Slot
Upper Right Side
Touch Screen
Terminal Front Bezel
Front Bezel
24772
Figure 2.9 Keypad Terminal Clip Mount (Back View)
Mounting Slot
Foot Pad
Screwdriver Slot
Panel Mount Screw
Mounting Clip
24780
Publication 2711E-6.17 – November 1998
2–10
Installing PanelView 1000e Terminals
3. Tighten the mounting clip screws to a torque of 10 inch-pounds.
Do not over-tighten.
!
ATTENTION: Tighten mounting clips to a torque of
10 inch-pounds to provide a proper seal and to prevent
potential damage to the terminal. Allen-Bradley
assumes no responsibility for water or chemical
damage to the terminal or other equipment within the
enclosure because of improper installation.
4. Remove the protective installation label covering the top vents of
the terminal.
!
ATTENTION: Remove the protective installation
label covering the top vents to prevent overheating and
damage to the terminal.
Mounting a Touch Screen Terminal in a 19-inch Rack
To mount the PanelView 1000e Clip-Mount Touch Screen terminals
in a standard 19-inch EIA rack, you need a Rack Mount Kit (A-B
Catalog Number 2711-NR6T). This kit consists of a rack adapter and
mounting hardware.
Mounting a Keypad Terminal in a 19-inch Rack
To mount the PanelView 1000e Clip-Mount Keypad terminals in a
standard 19-inch EIA rack, you need a Rack Mount Kit (A-B
Catalog Number 2711-NR6K). This kit consists of a rack adapter and
mounting hardware.
Publication 2711E-6.17 – November 1998
Installing PanelView 1000e Terminals
Setting Up the PanelView
1000e Terminal
2–11
You have several options for setting up the terminal. Figure 2.1
shows the locations of the options described in the remainder of this
chapter.
Switching Modes
The terminal operates in Configure and Run modes. Configure mode
lets you set up the terminal and Run mode executes the application
file. To switch between modes, use either of the following methods:
• the hardware Mode Select Keyswitch, at the back of the terminal
• the Software Mode Switch (available in PanelView firmware
version 3 and above) that you can set to Enable or Disable from
the Terminal Configuration screen. For details, see Mode Switch
in Chapter 5 of this manual.
"
Note: The terminal communicates with your PLC only when the
terminal is in Run mode, so set it to this mode to monitor and control
your PLC application.
Backlight Intensity
You can adjust the terminal display intensity while in Configure
mode. For details on how to increase or decrease terminal display
intensity, see Chapter 5, Configuring PanelView Terminals, in this
manual. The terminal display is initially set at the maximum
intensity.
Connecting Power to the Terminal
The power requirements for the terminal are 115 Vac (60 Hz) or
230 Vac (50 Hz).
Before connecting the power cable to the power connector at the
bottom of the terminal, make sure the cable is not carrying power.
Because the terminal has no power switch, connecting the ac power
will start the terminal if power is present in the cable.
!
ATTENTION: Be sure to connect the wire to Ground
(GND) on the power connector. Failure to do so could
result in electrical hazard to the operator (and damage
to the equipment).
Publication 2711E-6.17 – November 1998
2–12
Installing PanelView 1000e Terminals
To connect power to the terminal:
1. Prepare the power wires by stripping the wire of its protective
coating to a length of to of an inch (1 to 2 cm).
2. Turn the screw on the power connector counter-clockwise to open
the wire slot. Insert the wire fully into its appropriate slot.
3. Turn the screw clockwise until the wire is held firmly in place.
4. Repeat the procedure until all three power wires are connected.
Figure 2.10 The Power Connector
L1
L1 ~ (Vac)
L2
L2N ~ (Vac)
GND
(Protective Earth)
20164
Connecting the Upload/Download Cable
The RS-232 port connects the terminal to the host computer for
uploading and downloading application files using the RS-232 serial
cable (Upload/Download cable). Cables of different lengths are
available in separate kits (A-B Catalog Numbers 2711-NC13,
2711-NC14, 2706-NC13).
The Upload/Download cable can be connected to a computer with a
9-pin, RS-232 port (IBM PC AT-type computers). Use the cable
pinout shown in Figure 2.11 to connect the terminal to the host
computer. For instructions about transferring files using the
Upload/Download cable, refer to the PanelBuilder 1400e
Configuration Software for Windows User Manual or the
PanelView e Transfer Utility User Manual.
Publication 2711E-6.17 – November 1998
Installing PanelView 1000e Terminals
2–13
Figure 2.11 RS-232 Port Pinout for Upload/Download Cable
Connection
PanelView Terminal Cable End
RS-232 Port Pinout
Female, 9-pin
Host Computer Cable End
RS-232 Port Pinout
Female, 9-pin
DCD (1)
TXD (2)
RXD (3)
DSR (4)
Common (5)
DTR (6)
CTS (7)
RTS (8)
N/C (9)
DCD (1)
RXD (2)
TXD (3)
DTR (4)
Common (5)
DSR (6)
RTS (7)
CTS (8)
N/C (9)
Connecting the Serial Printer
You will need to construct your own cable to connect a serial printer
to the terminal. Use the pinout shown in Figure 2.12 to construct the
PanelView terminal end of this cable. To construct the printer end of
the cable, consult the user manual for your printer.
Figure 2.12 RS-232 Port Pinout for Serial Printer Cable
Construction
RXD
TXD
DCD
DSR
Common
(ground)
Pin 5
Pin 9
Pin 1
Pin 6
DTR
CTS
RS-232 Serial Interface
Female, D-sub, 9-pin connector
N/C
RTS
20387
Connecting the Dataliner
Figure 2.13 shows the connection between a PanelView RS-232 port
and a Dataliner display device. See the Dataliner manual for more
information.
Figure 2.13 PanelView RS-232 Port and Dataliner
Connection
Publication 2711E-6.17 – November 1998
2–14
Installing PanelView 1000e Terminals
Connecting an External Alarm Relay
The terminal can be used to trigger a remote alarm or warning light
under specific conditions. See Appendix A, Specifications, in this
manual for the voltage range of the alarm relay.
!
!
ATTENTION: Do not use this relay for control
functions of any kind.
ATTENTION: The 1000e external alarm relay is rated
for 24 V ac or dc, and 1.0 ampere. Do not exceed the rated
values. The external alarm relay is different for the 1200e
and 1400e terminals.
To attach a remote alarm or light to the alarm relay connector:
1. Prepare the wires by stripping them of their insulation to a length
of to of an inch (1 to 2 cm).
2. Turn the screw on the alarm relay plug counter-clockwise to open
the wire slot.
3. Insert the wire fully into its appropriate slot. Figure 2.14 shows
the slots.
4. Turn the screw clockwise until the wire is held firmly in place.
5. Repeat the procedure until all three wires are connected.
Figure 2.14 The Remote Alarm Relay Connector
On bottom of PanelView 1000e
Terminal
(Refer to Figure 2.1)
Alarm Relay Connector
Normally
Common
Closed
Normally No
Connect
Open
20388
Publication 2711E-6.17 – November 1998
Installing PanelView 1000e Terminals
2–15
Connecting a Terminal to Your PLC System
Figure 2.15 shows the Remote I/O and DH+ connector on the bottom
of the terminal. This connects the terminal to the host PLC over
Remote I/O or DH+.
Figure 2.15 Remote I/O and DH+ Connector
On bottom of PanelView 1000e Terminal
(Refer to Figure 2.1)
Remote I/O and DH+ Connector
provided with installation kit
Remote I/O
PanelView Terminal
Pin1 Blue
Shield
Pin 2 Clear
2
SHIELD
PLC
Pin 1 Blue
Shield
Pin 2 Clear
1
DH+
PanelView Terminal
Pin1 Clear
Shield
Pin 2 Blue
PLC
Pin 1 Clear
Shield
Pin 2 Blue
20163
To connect the PanelView 1000e terminal over Remote I/O:
1. Remove the Remote I/O and DH+ connector plug from the
bottom of the terminal. Figure 2.1 shows its location.
2. Turn terminal screws 2 and 1 on the connector counter-clockwise.
See Figure 2.15 for plug connection locations.
3. Connect the clear wire to plug terminal 2 and the blue wire to
plug terminal 1. Connect shield and shield drain wire to middle
plug terminal. Tighten the screws to secure the wires.
4. Re-insert the plug into the terminal connector.
"
Note: If the terminal is the last device on the link, connect a watt
terminating resistor across terminals 1 and 2. The value of the
resistor depends on the Remote I/O baud rate:
• for 57.6 kilobaud and 115.2 kilobaud, use a 150-ohm resistor
(A-B Part Number 740018-29)
• for 230.4 kilobaud, use an 82-ohm resistor (A-B Part Number
740018-23)
Publication 2711E-6.17 – November 1998
2–16
Installing PanelView 1000e Terminals
To connect the PanelView 1000e terminal to the DH+ network:
1. Remove the Remote I/O and DH+ connector plug from the rear of
the terminal.
2. Turn terminal screws 2 and 1 on the connector counter-clockwise.
See Figure 2.15 for plug connection locations.
3. Connect the clear wire to plug terminal 1 and the blue wire to
plug terminal 2. Connect shield and shield drain wire to middle
plug terminal. Tighten the screws to secure the wires.
4. Re-insert the plug into the terminal connector.
"
Note: If the terminal is the last device on the link, connect a watt
terminating resistor across terminals 1 and 2. The value of the
resistor depends on the DH+ baud rate:
• for 57.6 kilobaud and 115.2 kilobaud, use a 150-ohm resistor
(A-B Part Number 740018-29)
• for 230 kilobaud, use an 82-ohm resistor (A-B Part Number
740018-23)
To connect the PanelView 1000e terminal to the ControlNet network:
The PanelView 1000e terminal (A-B Catalog Number 2711E-T10C6
and 2711E-K10C6) requires an enhancement with a 1784-KTCX,
1784-KTCX15, or 1784-KTCS card and 2711E-NA2 adapter. You
can use the ControlNet-enhanced PanelView 1000e terminals (A-B
Catalog Number 2711E-T10C7, 2711E-T10C15, 2711E-K10C7, and
2711E-K10C15).
"
Connect a PanelView Terminal to a ControlNet network via a tap
with a 1-meter (39.4-inch) drop cable. Use any tap with one of
the following catalog numbers: 1786-TPS, 1786-TPYS,
1786-TPR, or 1786-TPYR. See the ControlNet PLC-5
Programmable Controllers User Manual (A-B Publication
1785-6.5.14) for more information about ControlNet taps.
"
Note: ControlNet taps contain passive electronics and must be
purchased from Allen-Bradley for the network to operate correctly.
"
Note: If the terminal is the last device on the link, connect a 75-ohm,
1-watt terminating resistor to the unused connector on the tap (A-B
Catalog Number 1786-XT).
See the ControlNet PLC-5 Programmable Controllers User Manual
(A-B Publication 1785-6.5.14), the ControlNet Communication
Interface Card (A-B Publication 1784-5.20), and the ControlNet
Planning and Installation Manual (A-B Publication 1786-6.2.1) for
more information about ControlNet.
Publication 2711E-6.17 – November 1998
Installing PanelView 1000e Terminals
2–17
Using the PCMCIA Card Slots
The PCMCIA card slots support the PCMCIA memory cards, written
to in FAT file format. Only slot 1 is active. Slot 2 is covered with a
protective label. If a card is inserted to slot 2, there will be no
activity. See Figure 2.1 for the location of the PCMCIA card slots on
the bottom of your terminal.
Using a Keyboard or Bar Code Reader
The terminal supports a keyboard or a bar code reader, which you
can connect to the terminal’s keyboard port. See Figures 2.16 and
2.17 for the location of the keyboard port on the bottom of the
terminal. The keyboard port is covered with a protective, clear label.
Remove the label to expose the keyboard port.
The supported keyboards (A-B Part Numbers 6189-KBM1,
6189-KBD1, and 6189-KBE1) or supported bar code reader (A-B
Part Number 2755HDG4 Series A, Revision C) can be used with:
• ASCII Input Objects (for touch screen and keypad terminals)
• Numeric Entry Keypad Object (for touch screen terminals only)
• Numeric Keypad Enable Button (for keypad terminals only)
• Numeric Input Cursor Point (for keypad terminals only)
• Set Bit Cursor Point (for keypad terminals only)
For more information on touch screen or keypad input objects, see
the PanelBuilder 1400e Configuration Software for Windows
Reference Manual.
Figure 2.16 shows the keyboard connection to the PanelView 1000e
terminal. Figure 2.17 shows the bar code reader connection to the
PanelView 1000e terminal, with the option of connecting the
keyboard.
Publication 2711E-6.17 – November 1998
2–18
Installing PanelView 1000e Terminals
Figure 2.16 Keyboard Connection to the Terminal
Publication 2711E-6.17 – November 1998
Installing PanelView 1000e Terminals
2–19
Figure 2.17 Bar Code Reader and Keyboard (Optional)
Connection to the Terminal
Publication 2711E-6.17 – November 1998
Installing PanelView 1200e
Terminals
Overview
This chapter explains how to install a PanelView 1200e terminal.
Specifically, it provides:
• terminal dimensions
• a list of tools for installing the terminal
• cutout dimensions for panel mounting
• information about mounting options
This chapter also provides information about the correct use of the
following hardware features, specifically:
• how to adjust contrast and brightness
• how to switch modes
• how to connect power to the terminal
• how to connect the Upload/Download cable
• how to connect a serial printer
• how to connect the Dataliner
• how to connect an external alarm relay
• how to connect a terminal to your PLC system
• information about PCMCIA cards
Refer to Chapter 1 for information about the Upload/Download cable
and remote keyswitch assembly.
Figure 3.1 shows the rear panel of the PanelView 1200e terminal.
Note the location of the power connector, alarm relay connector,
RS-232 port, and Remote I/O and DH+ connector.
Publication 2711E-6.17 – November 1998
3–2
Installing PanelView 1200e Terminals
Figure 3.1 Rear View of PanelView 1200e Terminal
Contrast Control
Fuses
Power Connector
Alarm Relay Connector
Communication Slot
PCMCIA Memory Card Slot
RS-232 Port
Mode Select Keyswitch
Remote I/O & DH+ Connector
Brightness Control
Publication 2711E-6.17 – November 1998
23744
Installing PanelView 1200e Terminals
PanelView 1200e Terminal
Dimensions
3–3
Figures 3.2 and 3.3 show the dimensions of the keypad and touch
screen terminals.
Figure 3.2 PanelView 1200e Keypad Terminal Dimensions
2.05”
(52 mm)
0.68”
(17 mm)
12.46”
(316 mm)
1.71”
(43 mm)
1.83”
(46 mm)
Stud Size: #10-32
14.83”
4.8”
(377 mm)
(122 mm)
Stud Diameter: 7/32” (5.56mm)
Stud Height (from gasket to stud end):
0.5”
(12.7 mm)
0.78” 4.35”
4.35”
(20 mm) (110 mm) (110 mm)
4.35”
(110 mm)
4.35” 0.78”
(110 mm) (20 mm)
0.36”
(9 mm)
24779
1.02”
(26 mm)
0.70”
(18 mm)
Allen–Bradley
4.0”
(102 mm)
3.0”
(76 mm)
4.0”
(102 mm)
0.70”
(18 mm)
PanelView 1200e
F17
F18
12.40”
(315 mm)
F19
7 8 9
4 5 6
1 2 3
•
A
F20
F21
0
–
A
Y
A
HOME
13.97”
(355 mm)
"
B
FF3
2F9 F10
2 F11
2
0 0 0
F1
F
2.02”
(51 mm)
0.59”
(15 mm)
0.25”
(6 mm)
0.40”
(10 mm)
F2
F
F4
F12
FF5 F6
F
F13
2 F14
2
0 0
F7
F15
Raise
SELECT
Lower
CANCEL
FF8F8
F16
2
0
19.00”
(483 mm)
15.08”
(383 mm)
22168b
Publication 2711E-6.17 – November 1998
3–4
Installing PanelView 1200e Terminals
Figure 3.3 PanelView 1200e Touch Screen Terminal
Dimensions
12.46”
2.05”
(52 mm)
Stud Size: #10-32
Stud Diameter:
13/64” (5.16mm) – 7/32” (5.56mm)
0.69” (316 mm)
(18 mm)
1.71”
(43 mm)
0.70”
(18 mm)
0.70”
(18 mm)
14.83”
(377 mm)
Stud Height (from gasket to stud end):
0.5”
(12.7 mm)
0.4”
(10 mm)
0.59”
(15 mm)
4.1”
(104 mm)
4.1”
(104 mm)
4.1”
(104 mm)
4.35”
(110 mm)
4.30”
4.35”
(109 mm) (110 mm)
0.4”
(10 mm)
0.68”
(17 mm)
0.78”
(20 mm)
2.0”
(51 mm)
6.0”
(152 mm)
12.40”
(315 mm)
13.50”
(342 mm)
4.4”
(112 mm)
Allen–Bradley
0.52”
(13 mm)
0.68”
(17 mm)
2.02”
(51 mm)
0.40”
(10 mm)
15.31”
(389 mm)
Publication 2711E-6.17 – November 1998
PanelView 1200e
13.80”
(351 mm)
221
Installing PanelView 1200e Terminals
Tools for Installing Your
PanelView 1200e Terminal
"
3–5
You need the following tools to make a wall or panel cutout and
install a PanelView 1200e terminal in it. The terminal shipment
includes a terminal cutout template for your use.
Note: Conversions of metric/U.S. imperial values may have been
rounded off and therefore may not be exact conversions. This applies
to the dimensions specified in the drawings in this document.
To make a wall or panel cutout, you need these tools:
• center punch
• scriber
• hammer
• power jig saw
• set of drill bits (1/8 to 3/8 inch)
• metal ruler for drawing lines on the panel
• power drill
• metal file
To install the terminal, you need these tools:
• 3/8-inch socket drivers
• 11/32-inch socket drivers
• a minimum 14-inch extension rod
• ratchet screwdriver
• slot screwdriver (for clip-mount only)
Mounting Options for
PanelView 1200e
Terminals
You can mount your PanelView 1200e terminal in a rectangular
cutout in a panel or wall or in a 19-inch rack. Depending on the
model, the terminals are mounted with mounting studs or mounting
clips.
"
Note: When choosing a location in which to install the PanelView
terminal, we recommend you provide at least three inches (8 cm)
clearance around the sides and rear of the terminal. Leave at least six
inches (15 cm) clearance from the bottom of the terminal’s logic
board drawer, so you can open the logic board drawer without
removing the terminal from the panel or rack in which it is installed.
Publication 2711E-6.17 – November 1998
3–6
Installing PanelView 1200e Terminals
Mounting a Stud-Mount Keypad or Touch Screen Terminal in a
Panel or Wall Cutout
"
Note: Stud-mounted terminals have a NEMA 4X rating.
1. Make the appropriate cutout in the wall or panel location. Figures
3.4 and 3.5 show the cutout dimensions for the stud-mount
keypad and touch screen terminals. Figure 3.6 shows how the
older T30 panel cutout needs to be modified to fit the PanelView
1200e keypad terminals.
2. Place the terminal in the cutout, aligning the studs with the holes
in the rack.
3. Insert the terminal until the gasket material is flush with the wall
cutout or panel.
4. Nuts are provided with the stud-mount terminal models. Tighten
the nuts to compress the gasket on the terminal.
Built-in spacers prevent the gasket from being over-compressed. The
tightening torque increases significantly when you reach the correct
compression. At this point the tightening torque should not exceed
10 inch-pounds.
Figure 3.4 Stud-Mount Keypad Terminal Panel Cutout
CL
16.90I
16.90”
(429
(429 mm)
mm)
CL
1.50I
(38 mm)
CL
CL
12.85I
(326 mm)
5.50I
CUTOUT
8.70I
(221 mm)
9.16I
(233 mm)
5.50I
(140 mm)
6.70I
(170 mm)
1.50I
4.35I
(110 mm)
Publication 2711E-6.17 – November 1998
7/32I (5.56mm) DIA. TYP. 18 PLACES
MOUNTING STUDS ARE #10–32 SIZE
6.70I
4.35I
8.70I
9.16I
20182
Installing PanelView 1200e Terminals
3–7
Figure 3.5 Stud-Mount Touch Screen Terminal Panel Cutout
13/64I (5.16 mm) – 7/32I (5.56 mm) DIA.
TYP. 12 PLACES
MOUNTING STUDS ARE #10–32 SIZE
13.00I
(330 mm)
4.30I
(109 mm)
6.24I
(158 mm)
12.69I
(322 mm)
12.50I
(316 mm)
2.05I
(52 mm)
4.10I
(104 mm)
2.05I
CUTOUT
CL
12.69I
(322 mm)
6.35I
(161 mm)
12.91I
(328 mm)
6.46I
(164 mm)
4.30I
(109 mm)
12.50I
(318 mm)
13.00I
(330 mm)
13.11I
(333 mm)
21181
Figure 3.6 Modification to T30 Panel Cutout for Stud-Mount
Keypad Terminals
7/32I (5.56 mm) DIA. TYP. 18 PLACES
MOUNTING STUDS ARE #10–32 SIZE
1.08I
(27 mm)
CUTOUT
6.43I
(163 mm)
1.50I
(38 mm)
16.90I
(429 mm)
12.85I
(326 mm)
6.43I
CL
5.50I
(140 mm)
6.70I
(170 mm)
1.50I
CL
5.50I
CUTOUT
CUTOUT
1.08I
4.35I
(110 mm)
8.70I
(221 mm)
9.16¨¨I
(233 mm)
6.70I
4.35I
8.70I
9.16I
20183
Publication 2711E-6.17 – November 1998
3–8
Installing PanelView 1200e Terminals
Mounting a Clip-Mount Touch Terminal in a Panel or Wall Cutout
"
Note: Clip-mount touch screen terminals have NEMA 12 and
13 ratings.
1. Make the appropriate cutout in the wall or panel location. Figure
3.7 shows the cutout dimensons for the clip-mount terminal.
2. Insert the terminal into the panel or wall cutout.
Figure 3.7 Clip-Mount Touch Screen Terminal Panel
Cutout
CL
6.25”
(159 mm)
12.50”
(318 mm)
CUTOUT
CL
CL
CL
12.50”
(318 mm)
23651
Four mounting clips are provided with the clip-mount touch
screen terminals. See Figures 3.8 and 3.9 for details of the
following procedures.
To assemble the clips:
1. Snap the foot pad onto the end of the panel mount screw.
2. Insert the screw into the mounting clip from the front until less
than one inch of the screw protrudes from the front of the
mounting clip.
To install the clips:
1. Hook each clip into its mounting slot on the side of the terminal.
2. Tighten the screws until the chassis is held snugly in place against
the panel. A torque of 10 inch-pounds provides a good seal. Do
not over-tighten the screws.
Publication 2711E-6.17 – November 1998
Installing PanelView 1200e Terminals
3–9
Figure 3.8 Touch Screen Clip Mount (Side View)
Gasket
Screwdriver Slot
Rack Mount Adapter
or User Panel
Mounting
Clip
Mounting Slot
Upper Right Side
Touch Screen Terminal
Front Bezel
Front Bezel
21313
Figure 3.9 Touch Screen Clip Mount (Back View)
Rack Mount Adapter
or User Panel
Mounting Slot
Foot Pad
Panel Mount Screw
Screwdriver Slot
Mounting Clip
23738
Publication 2711E-6.17 – November 1998
3–10
Installing PanelView 1200e Terminals
Mounting a Stud-Mount Keypad Terminal in a 19-inch Rack
You can mount a PanelView 1200e Stud-Mount Keypad terminal in a
standard EIA 19-inch rack. No additional hardware is required.
To mount the terminal:
1. Place the terminal in the rack, aligning the studs with the holes in
the rack.
2. Insert the terminal until the gasket material is flush with the wall
cutout or panel.
3. Nuts are provided with the stud-mount terminal models. Tighten
the nuts to compress the gasket on the terminal.
Built-in spacers prevent the gasket from being over-compressed. The
tightening torque increases significantly when you reach the correct
compression. At this point the tightening torque should not exceed
10 inch-pounds.
Mounting a Touch Screen Terminal in a 19-inch Rack
To mount the PanelView 1200e Clip-Mount or Stud-Mount Touch
Screen terminals in a standard 19-inch EIA rack, you need a Rack
Mount Kit (A-B Catalog Number 2711-NR1). This kit consists of a
rack adapter and mounting hardware.
Setting Up the PanelView
1200e Terminal
You have several options for setting up the terminal. Figure 3.1
shows the locations of the options described in the remainder of this
chapter.
Adjusting Contrast and Brightness
The Contrast and Brightness Controls adjust the terminal display
intensity and contrast. The terminal display is set at the factory.
To increase terminal contrast and brightness:
"
Turn the controls clockwise.
To decrease terminal contrast and brightness:
"
Publication 2711E-6.17 – November 1998
Turn the controls counter-clockwise.
Installing PanelView 1200e Terminals
3–11
Switching Modes
The terminal operates in Configure and Run modes. Configure mode
lets you set up the terminal and Run mode executes the application
file. To switch between modes, use either of the following methods:
• the hardware Mode Select Keyswitch, at the back of the terminal.
• the Software Mode Switch (available in PanelView firmware
version 3 and above) that you can set to Enable or Disable from
the Terminal Configuration screen. For details, see Mode Switch
in Chapter 5 of this manual.
"
Note: The terminal communicates with your PLC only when the
terminal is in Run mode, so set it to this mode to monitor and control
your PLC application.
With the optional Remote Keyswitch Assembly, you can access the
Mode Select Keyswitch and RS-232 port from the front of the rack
where the terminal is mounted. It is available in a separate kit (A-B
Catalog Number 2711-NC2). For complete mounting instructions,
refer to Remote Keyswitch and RS-232 Port Assembly Installation
Data (A-B Publication 2711-5.2).
Connecting Power to the Terminal
Power requirements for the terminal are 115 Vac (60 Hz) or 230 Vac
(50 Hz).
Before connecting the power cable to the power connector at the rear
of the terminal, make sure the cable is not carrying power. Because
the terminal has no power switch, connecting the ac power will start
the terminal if power is present in the cable.
!
ATTENTION: Be sure to connect the wire to Ground
(GND) on the power connector. Failure to do so could
result in electrical hazard to the operator (and damage
to the equipment).
!
ATTENTION: Both the ac supply and the relay
output connectors look the same so be very careful to
wire them correctly. Incorrect power wire connection
can damage the terminal.
Publication 2711E-6.17 – November 1998
3–12
Installing PanelView 1200e Terminals
To connect power to the terminal:
1. Prepare the power wires by stripping the wire of its protective
coating to a length of to of an inch (1 to 2 cm).
2. Turn the screw on the power connector counter-clockwise to open
the wire slot.
3. Insert the wire fully into its appropriate slot.
4. Turn the screw clockwise until the wire is held firmly in place.
5. Repeat the procedure until all three power wires are connected.
Figure 3.10 The Power Connector
L1
L1 ~ (Vac)
L2
L2N ~ (Vac)
GND
(Protective Earth)
20164
Connecting the Upload/Download Cable
The RS-232 port connects the terminal to the host computer for
uploading and downloading application files using the RS-232 serial
cable (Upload/Download cable). The cable is available in a separate
kit (A-B Catalog Number 2711-NC1).
The Upload/Download cable can be connected to a computer with a
25-pin, RS-232 port (IBM PC AT-type computers). Use the cable
pinout shown in Figure 3.11 to connect the terminal to the host
computer. For instructions about transferring files using the
Upload/Download cable, refer to the PanelView e Transfer Utility
User Manual.
Publication 2711E-6.17 – November 1998
Installing PanelView 1200e Terminals
3–13
Figure 3.11 RS-232 Port Pinout for Upload/Download Cable
Connection
PanelView Terminal Cable End
RS-232 Port Pinout
Female, 25-pin
Host Computer Cable End
RS-232 Port Pinout
Female, 9-pin
SHIELD (1)
RXD (2)
TXD (3)
CTS (4)
RTS (5)
DTR (6)
Common (7)
DCD (8)
DSR (20)
NC
TXD (3)
RXD (2)
RTS (7)
CTS (8)
DSR (6)
Common (5)
DCD (1)
DTR (4)
Connecting the Serial Printer
You will need to construct your own cable to connect a serial printer
to the terminal. Use the pinout shown in Figure 3.12 to construct the
terminal end of this cable. To construct the printer end of the cable,
consult the user manual for your printer.
Figure 3.12 RS-232 Port Pinout for Serial Printer Cable
Construction
RTS (5)
DTR (6)
Common (7)
DCD (8)
CTS (4)
TXD (3)
RXD (2)
SHIELD (1)
Pin 1
Pin 14
DSR (20)
RS-232 Serial Interface
Female, D-sub, 25-pin connector
20157
Publication 2711E-6.17 – November 1998
3–14
Installing PanelView 1200e Terminals
Connecting the Dataliner
Figure 3.13 shows the connection between a PanelView RS-232 port
and a Dataliner display device. See the Dataliner manual for more
information.
Figure 3.13 PanelView RS-232 Port and Dataliner
Connection
Connecting an External Alarm Relay
The terminal can be used to trigger a remote alarm or warning light
under specific conditions. See Appendix B, Specifications, for the
voltage range of the alarm relay.
!
ATTENTION: Do not use this relay for control
functions of any kind.
To attach a remote alarm or light to the alarm relay connector:
1. Prepare the wires by stripping them of their insulation to a length
of to of an inch (1 to 2 cm).
2. Turn the screw on the alarm relay connector counter-clockwise to
open the wire slot.
3. Insert the wire fully into its appropriate slot. Figure 3.14 shows
the slots.
4. Turn the screw clockwise until the wire is held firmly in place.
5. Repeat the procedure until all three wires are connected.
Publication 2711E-6.17 – November 1998
Installing PanelView 1200e Terminals
3–15
Figure 3.14 The Remote Alarm Connector
N/C
N/O
COM
21162
Connecting a Terminal to Your PLC System
Figure 3.15 shows the Remote I/O and DH+ connector on the back
of the terminal. This connects the terminal to the host PLC controller
over Remote I/O or DH+.
Figure 3.15 Remote I/O and DH+ Connector
On rear of PanelView 1200e Terminal
(Refer to Figure 3.1)
Remote I/O and DH+ Plug
provided with installation kit
Remote I/O
PanelView Terminal
Pin1 Blue
Shield
Pin 2 Clear
2
SHIELD
PLC
Pin 1 Blue
Shield
Pin 2 Clear
1
DH+
PanelView Terminal
Pin1 Clear
Shield
Pin 2 Blue
PLC
Pin 1 Clear
Shield
Pin 2 Blue
20163
Publication 2711E-6.17 – November 1998
3–16
Installing PanelView 1200e Terminals
To connect the PanelView 1200e terminal over Remote I/O:
1. Remove the Remote I/O and DH+ connector plug from the rear of
the terminal. Figure 3.1 shows its location.
2. Turn terminal screws 2 and 1 on the connector counter-clockwise.
See Figure 3.15 for plug connection locations.
3. Connect the clear wire to plug terminal 2 and the blue wire to
plug terminal 1. Connect shield and shield drain wire to middle
plug terminal.
4. Tighten the screws to secure the wires.
5. Re-insert the plug into the terminal connector.
"
Note: If the terminal is the last device on the link, connect a 1/2 watt
terminating resistor across terminals 1 and 2. The value of the
resistor depends on the Remote I/O baud rate:
• for 57.6 kilobaud and 115.2 kilobaud, use a 150-ohm resistor
(A-B Part Number 740018-29)
• for 230 kilobaud, use an 82-ohm resistor (A-B Part Number
740018-23)
To connect the PanelView 1200e terminal to the DH+ network:
1. Remove the Remote I/O and DH+ connector plug from the rear of
the terminal. Figure 3.1 shows its location.
2. Turn terminal screws 2 and 1 on the connector counter-clockwise.
See Figure 3.15 for plug connection locations.
3. Connect the clear wire to plug terminal 1 and the blue wire to
plug terminal 2. Connect shield and shield drain wire to middle
plug terminal.
4. Tighten the screws to secure the wires.
5. Re-insert the plug into the terminal connector.
"
Publication 2711E-6.17 – November 1998
Note: If the terminal is the last device on the link, connect a 1/2 watt
terminating resistor across terminals 1 and 2. The value of the
resistor depends on the DH+ baud rate:
• for 57.6 kilobaud and 115.2 kilobaud, use a 150-ohm resistor
(A-B Part Number 740018-29)
• for 230 kilobaud, use an 82-ohm resistor (A-B Part Number
740018-23)
Installing PanelView 1200e Terminals
3–17
Using the PCMCIA Card Slot
The PCMCIA card slot supports the PCMCIA memory cards, written
to in FAT file format. Figure 3.1 shows the location of the PCMCIA
card slot on the back of your terminal.
For enhanced PanelView 1200 Series F and G terminals:
The PanelView 1200 Enhancement Kit (A-B Catalog Number
2711E-U1B12C) comes with the 4-MB PCMCIA card preloaded
with firmware.
In an enhanced Series F or above PanelView 1200 terminal, you can
also use any of the cards listed in Appendix B to store firmware and
application files. The firmware occupies up to 1.7 MB of space on
the PCMCIA card; the space remaining is available for application
file storage. Refer to the PanelBuilder 1400e Configuration Software
for Windows User Manual for information on using the PCMCIA
card.
For a PanelView 1200e terminal:
In a PanelView 1200e terminal, you can use any of the cards listed in
Appendix B for application file storage.
Publication 2711E-6.17 – November 1998
Installing PanelView 1400e
Terminals
Overview
This chapter describes how to install a PanelView 1400e terminal.
Specifically, it provides:
• terminal dimensions
• a list of tools for installing the terminal
• cutout dimensions for panel mounting
• details about mounting options
This chapter also provides specific information about the correct use
of the following hardware features, including:
• how to adjust contrast and brightness
• how to adjust horizontal and vertical position
• how to switch modes
• how to connect power to the terminal
• how to connect the Upload/Download cable
• how to connect a serial printer
• how to connect the Dataliner
• how to connect an external alarm relay
• how to connect a terminal to your PLC system
• how to connect a keyboard and/or a bar code reader
Refer to Chapter 1 for information about the Upload/Download
cable, remote keyswitch assembly, and PCMCIA memory card slot
kits.
Figure 4.1 shows the rear panel of the PanelView 1400e terminal.
Publication 2711E-6.17 – November 1998
4–2
Installing PanelView 1400e Terminals
Figure 4.1 Rear View of PanelView 1400e Terminals
Publication 2711E-6.17 – November 1998
Installing PanelView 1400e Terminals
PanelView 1400e Terminal
Dimensions
4–3
Figures 4.2 and 4.3 show the dimensions of the keypad and touch
screen terminals.
Figure 4.2 PanelView 1400e Keypad Terminal Dimensions
13.80”
0.83” (351 mm)
(21 mm)
Stud Size: #10-32
Stud Diameter: 7/32” (5.56mm)
2.78”
(71 mm)
15.90”
(404 mm)
1.2”
(30 mm)
3.7”
(94 mm)
Stud Height (from gasket to stud end):
0.5”
(12.7 mm)
0.78”
4.35”
4.35”
(20 mm) (110 mm) (110 mm)
4.35”
(110 mm)
0.81”
(21 mm)
4.35” 0.78”
(110 mm) (20 mm)
24778
0.59”
(15 mm)
0.90”
(23 mm)
4.0”
(102 mm)
PanelView 1400e
Allen–Bradley
F17
F18
3.0”
(76 mm)
F19
12.79”
(325 mm)
4.0”
(102 mm)
0.90”
(23 mm)
7
4
1
.
8
5
2
0
9
6
3
–
F20
13.97”
(355 mm)
F21
Home
F1
F2
F3
F4
F5
F6
F7
F8
F9 F10 F11 F12 F13 F14 F15 F16
SELECT
CANCEL
1.45”
(37 mm)
0.59”
(15 mm)
0.81”
(21 mm)
Raise
Lower
0.40”
(10 mm)
15.90”
(404 mm)
19.00”
(483 mm)
22168e
Publication 2711E-6.17 – November 1998
4–4
Installing PanelView 1400e Terminals
Figure 4.3 PanelView 1400e Touch Screen Terminal
Dimensions
13.8”
(351 mm)
2.78”
(71 mm)
0.83”
(21 mm)
Stud Size: #10-32
Stud Diameter: 7/32” (5.56mm)
1.80”
(46 mm)
15.90”
(404 mm)
Stud Height (from gasket to stud end):
1.80”
(46 mm)
0.5”
(12.7 mm)
3.69”
(93 mm)
0.60”
(15 mm)
5.00”
(127 mm)
0.75”
(19 mm)
5.00”
3.69”
(127 mm) (93 mm)
24778
1.40”
(35 mm)
Allen–Bradley
5.50”
(140 mm)
13.97”
(355 mm)
12.79”
(325 mm)
5.50”
(140 mm)
PanelView 1400e
1.40”
(35 mm)
1.45”
(37 mm)
0.59”
(15 mm)
0.75”
(19 mm)
0.40”
(10 mm)
15.90”
(404 mm)
Publication 2711E-6.17 – November 1998
17.38”
(442 mm)
22191e
Installing PanelView 1400e Terminals
Tools for Installing Your
PanelView 1400e Terminal
"
4–5
You need the following tools to make a wall or panel cutout and
install a PanelView 1400e terminal in it. The terminal shipment
includes a terminal cutout template for your use.
Note: Conversions of metric/U.S. customary values may have been
rounded off and therefore may not be exact conversions. This applies
to the dimensions specified in the drawings in this document.
To make a wall or panel cutout, you need these tools:
• center punch
• scriber
• hammer
• power jig saw
• set of drill bits (1/8 to 3/8 inch)
• metal ruler for drawing lines on the panel
• power drill
• metal file
To install the terminal, you need these tools:
• 3/8-inch socket drivers
• 11/32-inch socket drivers
• a minimum 14-inch extension rod
• ratchet screwdriver
Mounting Options for
PanelView 1400e
Terminals
You can install your PanelView 1400e terminal in a rectangular
cutout in a panel or wall or in a 19-inch rack. The terminals are
mounted with mounting studs.
"
Note: When choosing a location in which to install the PanelView
terminal, we recommend you provide at least three inches (8 cm)
clearance around the sides and rear of the terminal. Leave at least six
inches (15 cm) clearance from the bottom of the terminal’s logic
board drawer so you can open the drawer without having to remove
the terminal from the panel or rack.
Publication 2711E-6.17 – November 1998
4–6
Installing PanelView 1400e Terminals
Mounting a Stud-Mount Keypad or Touch Screen Terminal in a
Panel or Wall Cutout
"
Note: Stud-mounted terminals have a NEMA 4X rating.
1. Make the appropriate cutout in the wall or panel, following the
instructions on the template provided with the terminal. Figures
4.4 and 4.5 show the cutout dimensions for the touch screen and
keypad terminals.
2. Place the terminal in the cutout, aligning the studs with the holes
in the rack. Insert the terminal until the gasket material makes full
contact with the wall or panel.
3. Nuts are provided with the terminals. Tighten the nuts to
compress the gasket on the terminal. Built-in spacers prevent the
gasket from being over-compressed. The tightening torque
increases significantly when you reach the correct compression.
At this point, the tightening torque should not exceed
10 inch-pounds.
Figure 4.4 Stud-Mount Touch Screen Terminal Panel Cutout
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
Bezel Border Line
PANEL CUT–OUT LAYOUT
6.425”
(163.2 mm)
5.500”
(139.7 mm)
6.645”
(168.8 mm)
13.290”
(337.6 mm)
CL
12.850”
(326.4 mm)
13.970”
(354.8 mm)
5.500”
(139.7 mm)
CL
10.000”
(254.0 mm)
15.375”
(390.5 mm)
∅ 7/32” 12 Holes Typ.
16.700”
(424.2 mm)
17.38”
(441.5 mm)
Publication 2711E-6.17 – November 1998
24720b
Installing PanelView 1400e Terminals
4–7
Figure 4.5 Stud-Mount Keypad Terminal Panel Cutout
17.400
(442.0 mm)
8.700
(221.0 mm)
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
Bezel Border Line
PANEL CUT–OUT LAYOUT
PANEL CUT–OUT LAYOUT
6.425
6.700
(163.2 mm) (170.2 mm)
5.500
6.985
(139.7 mm)
(177.4 mm)
1.500
(38.1 mm)
13.970
(354.8 mm)
CL
1.500
(38.1 mm)
12.850
(326.4 mm)
6.700
(170.2 mm)
5.500
(139.7 mm)
CL
8.450
(214.6 mm)
4.350
(110.5 mm)
8.700
(221.0 mm)
9.156
(232.6 mm)
4.350
(110.5 mm)
16.900
(429.3 mm) 8.700
(221.0 mm)
19.00
(482.6 mm)
9.50
(241.3 mm)
∅ 7/32 18 Holes Typ.
9.156
(232.6 mm)
24721b
Mounting Your PanelView 1400e Terminal in a 19-inch Rack
You can mount a PanelView 1400e Stud-Mount Keypad terminal in a
standard EIA 19-inch rack. No additional hardware is required.
To mount the terminal:
1. Place the terminal in the rack, aligning the studs with the holes in
the rack.
2. Insert the terminal until the gasket material is flush with the wall
cutout or panel.
3. Nuts are provided with the stud-mount terminal models. Tighten
the nuts to compress the gasket on the terminal.
Built-in spacers prevent the gasket from being over-compressed. The
tightening torque increases significantly when you reach the correct
compression. At this point the tightening torque should not exceed
10 inch-pounds.
To mount a PanelView 1400e Stud-Mount Touch Screen terminal in
a standard 19-inch EIA rack, you require a Rack Mount Kit (Catalog
No. 2711-NR4).
Publication 2711E-6.17 – November 1998
4–8
Installing PanelView 1400e Terminals
Mounting Your Keypad Terminal in a T30 Cutout
Cutouts made for T30 devices require modification before accepting
the 1400e terminal. Figure 4.6 shows the required changes.
Figure 4.6 Modification to T30 Panel Cutout for 1400e
Keypad Terminals
7/32I (5.56 mm) DIA. TYP. 18 PLACES
MOUNTING STUDS ARE #10–32 SIZE
1.08I
(27 mm)
CUTOUT
6.43I
(163 mm)
1.50I
(38 mm)
16.90I
(429 mm)
12.85I
(326 mm)
6.43I
CL
1.50I
CL
5.50I
CUTOUT
CUTOUT
1.08I
4.35I
(110 mm)
8.70I
(221 mm)
9.16I
(233 mm)
Setting Up the PanelView
1400e Terminal
5.50I
(140 mm)
6.70I
(170 mm)
6.70I
4.35I
8.70I
9.16I
20183
There are several controls and connectors to consider when setting
up the terminal. Figure 4.1 shows the locations of the controls and
connectors described in the remainder of this chapter.
Adjusting Contrast and Brightness
The Contrast and Brightness Controls adjust the terminal display
intensity and contrast. The terminal display is set at the factory.
To increase terminal contrast and brightness, turn the controls
clockwise. To decrease terminal contrast and brightness, turn the
controls counter-clockwise. See Figure 4.1.
Publication 2711E-6.17 – November 1998
Installing PanelView 1400e Terminals
4–9
Adjusting Horizontal and Vertical Position
For any further adjustments, turn the horizontal and vertical knobs
on the side of the terminal, as shown in Figure 4.1.
Switching Modes
The terminal operates in Configure and Run modes. Configure mode
lets you set up the terminal and Run mode executes the application
file. To switch between modes, you can use either of the following
methods:
• the hardware Mode Select Keyswitch, located at the back of the
terminal.
• the Software Mode Switch (available in PanelView firmware
version 3 and above) that you can set to Enable or Disable from
the Terminal Configuration screen. For details, see Mode Switch
in Chapter 5 of this manual.
"
Note: The terminal communicates with your PLC only when the
terminal is in Run mode, so set it to this mode to monitor and control
your PLC application.
With the optional Remote Keyswitch Assembly, you can access the
Mode Select Keyswitch and RS-232 port from the front of the rack
where the terminal is mounted. It is available in a separate kit (A-B
Catalog Number 2711-NC2). For complete mounting instructions,
refer to Remote Keyswitch and RS-232 Port Assembly Installation
Data (A-B Publication 2711-5.2).
Connecting Power to the Terminal
Power requirements for the terminal are 115 Vac (60 Hz) or 230 Vac
(50 Hz).
Before connecting the power cable to the power connector at the rear
of the terminal, make sure the cable is not carrying power. Because
the terminal has no power switch, connecting the cable will start the
terminal if the cable is live.
Publication 2711E-6.17 – November 1998
4–10
Installing PanelView 1400e Terminals
!
ATTENTION: Be sure to connect the wire to Ground
(GND) on the power connector. Failure to do so could
result in electrical hazard to the operator and damage to
the equipment.
!
ATTENTION: Both the ac supply and the relay output
connectors look the same, so be careful to wire them
correctly. Incorrect power wire connection can damage
the PanelView 1400e terminal.
To connect power to the terminal:
1. Prepare the power wires by stripping the wire of its insulation to a
length of to of an inch (1 to 2 cm).
2. Turn the screw on the power connector counterclockwise to open
the wire slot.
3. Insert the wire fully into its appropriate slot.
4. Turn the screw clockwise until the wire is held firmly in place.
5. Repeat the procedure until all three power wires are connected.
Figure 4.7 The Power Connector
L1
L2
L1 ~ (Vac)
L2N ~ (Vac)
(Protective Earth)
GND
20164
See Figure 4.1 for the location of the power connector on the back of
the terminal.
Publication 2711E-6.17 – November 1998
Installing PanelView 1400e Terminals
4–11
Connecting the Upload/Download Cable
The RS-232 port connects the terminal to the host computer for
uploading and downloading application files using the RS-232 serial
cable (Upload/Download cable). The cable is available in a separate
kit (A-B Catalog Number 2711-NC1).
The Upload/Download cable can be connected to a computer with a
25-pin, RS-232 port (IBM PC AT-type computers). Use the cable
pinout shown in Figure 4.8 to connect the terminal to the host
computer. For instructions about transferring files using the
Upload/Download cable, refer to the PanelView e Transfer Utility
User Manual.
Figure 4.8 RS-232 Port Pinout for Upload/Download Cable
Connection
Host Computer Cable End
RS-232 Port Pinout
Female, 9-pin
PanelView Terminal Cable End
RS-232 Port Pinout
Female, 25-pin
SHIELD (1)
RXD (2)
TXD (3)
CTS (4)
RTS (5)
DTR (6)
Common (7)
DCD (8)
DSR (20)
NC
TXD (3)
RXD (2)
RTS (7)
CTS (8)
DSR (6)
Common (5)
DCD (1)
DTR (4)
Connecting the Serial Printer
To connect a serial printer to the terminal, you must construct your
own cable. Use the pinout as shown in Figure 4.9 to construct the
terminal end of this cable. To construct the printer end of the cable,
consult your printer’s user manual.
Figure 4.9 RS-232 Port Pinout for Serial Printer Cable
Construction
RTS (5)
DTR (6)
Common (7)
DCD (8)
CTS (4)
TXD (3)
RXD (2)
SHIELD (1)
Pin 1
Pin 14
DSR (20)
RS-232 Serial Interface
Female, D-sub, 25-pin connector
20157
Publication 2711E-6.17 – November 1998
4–12
Installing PanelView 1400e Terminals
Connecting the Dataliner
Figure 4.10 shows the connection between a PanelView RS-232 port
and a Dataliner display device. See the Dataliner manual for more
information.
Figure 4.10 PanelView RS-232 Port and Dataliner
Connection
Connecting an External Alarm Relay
The PanelView 1400e terminal can be used to trigger a remote alarm
or warning light under specific conditions. See Appendix C for the
voltage range of the alarm relay.
See Figure 4.1 for the location of the alarm relay connector on the
back of the terminal.
!
ATTENTION: Do not use this relay for control
functions of any kind.
To attach a remote alarm or light to the alarm relay connector:
1. Prepare the wires by stripping them of their insulation to a length
of to of an inch (1 to 2 cm).
2. Turn the screw on the alarm relay connector counterclockwise to
open the wire slot.
3. Insert the wire fully into its appropriate slot. See Figure 4.11 for
an illustration.
4. Turn the screw clockwise until the wire is held firmly in place.
5. Repeat the procedure until all three wires are connected.
Publication 2711E-6.17 – November 1998
Installing PanelView 1400e Terminals
4–13
Figure 4.11 The Remote Alarm Connector
N/C
N/O
COM
21162
Connecting a Terminal to Your PLC System
Figure 4.12 shows the Remote I/O and DH+ connector on the back
of the terminal. This connects the terminal to the host PLC over
Remote I/O or DH+.
Figure 4.12 Remote I/O and DH+ Connector
On rear of PanelView1400e Terminal
(Refer to Figure 4.1)
Remote I/O and DH+ Plug
provided with installation kit
Remote I/O
PanelView Terminal
Pin1 Blue
Shield
Pin 2 Clear
2
SHIELD
PLC
Pin 1 Blue
Shield
Pin 2 Clear
1
DH+
PanelView Terminal
Pin1 Clear
Shield
Pin 2 Blue
PLC
Pin 1 Clear
Shield
Pin 2 Blue
20163
Publication 2711E-6.17 – November 1998
4–14
Installing PanelView 1400e Terminals
To connect the PanelView 1400e terminal over Remote I/O:
1. Remove the Remote I/O and DH+ connector plug from the rear of
the terminal. Figure 4.1 shows its location.
2. Turn terminal screws 2 and 1 on the connector counter-clockwise.
See Figure 4.12 for plug connection locations.
3. Connect the clear wire to plug terminal 2 and the blue wire to
plug terminal 1. Connect shield and shield drain wire to middle
plug terminal.
4. Tighten the screws to secure the wires.
5. Re-insert the plug into the terminal connector.
"
Note: If the terminal is the last device on the link, connect a watt
terminating resistor across terminals 1 and 2.
• for 57.6 kilobaud and 115.2 kilobaud, use a 150-ohm resistor
(A-B Part Number 740018-29)
• for 230 kilobaud, use an 82-ohm resistor (A-B Part Number
740018-23)
To connect the PanelView 1400e terminal to the DH+ network:
1. Remove the Remote I/O and DH+ connector plug from the rear of
the terminal. Figure 4.1 shows its location.
2. Turn terminal screws 2 and 1 on the connector counter-clockwise.
See Figure 4.12 for plug connection locations.
3. Connect the clear wire to plug terminal 1 and the blue wire to
plug terminal 2. Connect shield and shield drain wire to middle
plug terminal.
4. Tighten the screws to secure the wires.
5. Re-insert the plug into the terminal connector.
"
Publication 2711E-6.17 – November 1998
Note: If the terminal is the last device on the link, connect a watt
terminating resistor across terminals 1 and 2.
• for 57.6 kilobaud and 115.2 kilobaud, use a 150-ohm resistor
(A-B Part Number 740018-29)
• for 230 kilobaud, use an 82-ohm resistor (A-B Part Number
740018-23)
Installing PanelView 1400e Terminals
4–15
To connect the PanelView 1400e terminal to the ControlNet network:
"
Connect a PanelView Terminal to a ControlNet network via a tap
with a 1-meter (39.4-in.) drop cable. Use any tap with one of the
following catalog numbers: 1786-TPS, 1786-TPYS, 1786-TPR,
or 1786-TPYR. See the ControlNet PLC-5 Programmable
Controllers User Manual (A-B Publication 1785-6.5.14) for more
information about ControlNet taps.
"
Note: ControlNet taps contain passive electronics and must be
purchased from Allen-Bradley for the network to function properly.
"
Note: If the terminal is the last device on the link, connect a 75-ohm,
1-watt terminating resistor to the unused connector on the tap (A-B
Catalog Number 1786-XT).
See the ControlNet PLC-5 Programmable Controllers User Manual
(A-B Publication 1785-6.5.14), the ControlNet Communication
Interface Card (A-B Publication 1784-5.20), and the ControlNet
Planning and Installation Manual (A-B Publication 1786-6.2.1) for
more information about ControlNet.
Using a Keyboard or Bar Code Reader
The terminal supports a keyboard or a bar code reader, which you
can connect to the terminal’s keyboard port. See Figures 4.13 and
4.14 for the location of the keyboard port on the bottom of the
terminal. The keyboard port is covered with a protective, black label.
Remove the perforated area of the label to expose the keyboard port.
The supported keyboards (A-B Part Numbers 6189-KBM1,
6189-KBD1, and 6189-KBE1) or supported bar code reader (A-B
Part Number 2755HDG4 Series A, Revision C) can be used with:
• ASCII Input Objects (for touch screen and keypad terminals)
• Numeric Entry Keypad Object (for touch screen terminals only)
• Numeric Keypad Enable Button (for keypad terminals only)
• Numeric Input Cursor Point (for keypad terminals only)
• Set Bit Cursor Point (for keypad terminals only)
For more information on touch screen or keypad input objects, see
the PanelBuilder 1400e Configuration Software for Windows
Reference Manual.
Figure 4.13 shows the keyboard connection to the PanelView 1400e
terminal. Figure 4.14 shows the bar code reader connection to the
PanelView 1000e terminal, with the option of connecting the
keyboard.
Publication 2711E-6.17 – November 1998
4–16
Installing PanelView 1400e Terminals
Figure 4.13 Keyboard Connection to the Terminal
Publication 2711E-6.17 – November 1998
Installing PanelView 1400e Terminals
4–17
Figure 4.14 Bar Code Reader and Keyboard (Optional)
Connection to the Terminal
Publication 2711E-6.17 – November 1998
Configuring PanelView
Terminals
This chapter describes the power-up and online tests and how to
configure a PanelView 1000e, 1200e, or 1400e operator terminal.
The terminal operates in either Configure or Run mode. You can set
up the terminal in Configure mode and execute your application file
in Run mode. The terminal communicates with your PLC only in
Run mode, so to monitor and control your PLC application, set the
terminal to Run.
Power-Up Functions
When you power up the terminal, several tests are done to determine
if there are any operational problems. When these tests are complete,
the terminal enters Configure or Run mode, depending on the Mode
Select Keyswitch setting.
Power On Self-Test (POST)
The BIOS and firmware validity are tested at power-up with the
Power-On Self Test (POST). If the test fails, an error message is
displayed that indicates the specific cause of the failure. If this
occurs, note the error message and contact your Allen-Bradley Sales
Representative.
Firmware Integrity Check
The firmware memory is also tested at power-up. If the firmware
memory test fails, the following message is displayed, followed by a
specific error message:
Firmware Upgrade Program Activated. x.x.x. MM–DD–YY
If this occurs, note the error message and contact your Allen-Bradley
Sales Representative.
Publication 2711E-6.17 – November 1998
5–2
Configuring PanelView Terminals
Battery Failure Test
The battery should last the life of the terminal. The battery is
monitored continuously.
If the battery fails, a Minor Fault message is displayed. As long as
the terminal’s power stays on, there is no problem. However, if
power is cycled to the terminal, the firmware or application file is
still in flash memory or on the PCMCIA card, but the application is
not selected, and retained values are lost. Retained values include
configuration parameters, retentive dataincluding last states,
current cursor point position, current cursor point status (enabled or
disabled)alarm history, and status information.
To clear the message and proceed, choose the Clear button. Contact
your Allen-Bradley Sales Representative to replace the board on
which the battery is situated. You will need to re-enter the
configuration parameters.
Watchdog Test
The Watchdog test verifies that the watchdog circuit can reset the
terminal. If the terminal fails this test, the following Major Fault
message is displayed:
Watchdog test failed
Contact your Allen-Bradley Sales Representative to service the
terminal.
Starting the Terminal in
Configuration Mode
To start the terminal in Configure mode, set the Mode Select
Keyswitch to Configure and connect the power. The Mode Select
Keyswitch is at the rear of the terminal.
You’ll want to start in Configure mode until you’ve configured the
terminal, downloaded your application file, and selected a current
application. When in Configure mode, the terminal will appear as a
faulted rack to your PLC (Remote I/O only) and will not be
recognized as a DH+ or ControlNet node.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
The Configuration Mode
Menu
5–3
With the Mode Select Keyswitch set to Configure mode, the 1000e,
1200e, and 1400e terminals display a Terminal Configuration screen.
For 1000e, 1200e, and 1400e Keypad terminals, the screen includes
function key labels. For 1000e, 1200e, and 1400e Touch Screen
terminals, the screen excludes function key labels .
The example below is for 1000e and 1400e Keypad terminals.
The example below is for the 1200e Keypad terminal. The screen
includes the Align Screen function.
To enable or disable Run Mode, choose the Security button and
select the Mode Switch tab. Set the Software Mode Switch to Enable
or Disable. For more details, see Mode Switch in this chapter.
"
Note: The Cancel button on subsequent screens discards any
changes made.
Publication 2711E-6.17 – November 1998
5–4
Configuring PanelView Terminals
Transferring Application
Files
There are two types of transfers:
• Downloadingtransferring a completed application from the
development computer to a terminal so the application can be run.
• Uploadingtransferring an existing application from a terminal
to the development computer so the application can be edited or
backed up.
Most application file transfers are controlled in PanelBuilder
software. The exception is a memory card transfer, whereby you
copy an application file to or from a PCMCIA memory card in the
terminal’s PCMCIA socket.
Methods of transferring application files between the terminal and
development computer and vice versa, are as follows:
• upload or download an application file using the
Upload/Download cable connecting the RS-232 ports of the
computer and terminal. This is a serial file transfer.
• upload or download the application file over a DH+ network.
This is a DH+ direct file transfer.
• upload or download the application file over a ControlNet
network. This is a ControlNet direct file transfer.
• upload or download the application file over DH+ and Remote
I/O networks, using the PLC-5 or SLC 5/04 Pass-Through
feature.
• upload or download the application file over ControlNet and
Remote I/O networks, using the PLC-5C Pass-Through feature.
• upload or download the application file over Ethernet, using the
Remote I/O Pass-Through feature.
Downloading using the Pass-Through, DH+ direct, or ControlNet
direct feature requires configuration in PanelBuilder 1400e
Configuration Software and in the Transfer Setup screen so the
network information and the PLC/SLC location on the network are
correct. For more information, refer to the PanelView e Transfer
Utility User Manual, or the section Pass-Through Application File
Transfers later in this chapter.
"
Tip: Use the new PLC Programming software (Who Active
command) to verify the terminal or PLC location on the DH+ or
ControlNet network. The PLC Programming software identifies the
terminal as PVe.
Important:
Publication 2711E-6.17 – November 1998
You may need to do the following before you initiate an
application file transfer:
Configuring PanelView Terminals
5–5
1. If you are uploading a file from the terminal, ensure that the
application file you want to upload is the Current Application.
See Selecting an Application later in this chapter for details.
2. You may need to set up the file transfer at the terminal. For
details about the Transfer Setup screen, consult the relevant
application file transfer section later in this chapter.
Serial Application File Transfers
To transfer application files serially, use the Upload/Download cable
to connect the development computer that contains the application
file to the terminal. You then transfer the application file directly to
or from the computer.
Summary of Steps
1. Using the Upload/Download cable, connect the serial port of the
development computer to the serial port of the terminal. For
information about the Upload/Download cable, see the
Installation Data Sheet included in the Upload/Download Cable
Kit (2711-NC1 for 1200e and 1400e terminals; 2711-NC13,
2711-NC14, and 2706-NC13 for 1000e terminals).
2. You should not need to change the default settings for
Upload/Download; the PanelBuilder 1400e Configuration
Software expects these settings. However, if you must change the
defaults, be sure you set the serial port on the PanelBuilder 1400e
development computer to the same settings. To change the default
communication settings for the serial port, use the Transfer Setup
screen.
3. When you are ready to upload or download the application file,
ensure you have the Transfer Application screen displayed at the
terminal.
4. Upload or download the application file to the terminal. This is
initiated at the development computer.
Publication 2711E-6.17 – November 1998
5–6
Configuring PanelView Terminals
To set up the serial application file transfer using the Transfer Setup
screen:
1. In the Terminal Configuration screen, choose the Transfer Setup
button to display the Transfer Setup screen.
For PanelView keypad terminals, the following Transfer Setup
screen appears.
For PanelView touch screen terminals, the following Transfer
Setup screen appears.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–7
2. To change the settings, choose the Baud Rate, Parity, or Error
buttons to move the check mark to the setting you want.
• Baud RateThe speed at which data is transmitted over the
serial cable. The default setting for a serial transfer is 9600
baud.
• ParityUsed to check data transferred between the
development computer and terminal. The default setting is
None.
• ErrorUsed to check for errors in data transmission and is
either
– CRCcyclical (or cyclic) redundancy check.
– BCCblock check character. BCC is the default setting.
3. When you have selected the required settings, choose OK to exit
this screen.
For detailed instructions on configuring the computer’s serial port,
see the PanelView e Transfer Utility User Manual.
To transfer an application serially:
1. In the Terminal Configuration screen, choose the Transfer
Application button to display the Transfer Application screen.
For PanelView keypad terminals, the following Transfer
Application screen appears.
Publication 2711E-6.17 – November 1998
5–8
Configuring PanelView Terminals
For PanelView touch screen terminals, the following Transfer
Application screen appears.
2. At the development computer, start the file upload or download.
Use PanelBuilder or the Transfer Utility. You must have the
Transfer Application screen displayed on the terminal.
"
Note: File transfers are initiated and controlled by the PanelView e
Transfer Utility 32. To cancel a file transfer at the terminal, switch
the terminal to Run mode or cycle power.
Once the upload or download has been initiated, a screen appears
that includes a progress meter. A message indicates when the upload
or download is complete.
If you are downloading to a data partition on a PCMCIA card or the
onboard application memory, and that data partition is full, you can
request the destination be formatted from the PanelBuilder computer.
You cannot stop a format operation. The Exit button is disabled.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–9
To run the downloaded application file:
If you’ve downloaded a file and specified it to be the Current
Application (in PanelBuilder), switch to Run mode to execute that
file. If you didn’t specify that the downloaded file is to be the
Current Application, use the Select Application screen to make it
current (unless it was the only file on the terminal at the end of the
download).
If there is no current (selected) application after a successful
download, the downloaded file is made current, regardless of the
setting. For more information, see “Selecting an Application” later in
this chapter.
You may also want to disconnect the Upload/Download cable and
re-connect your printer cable before switching to Run mode.
Memory Card Transfers
"
Note: For doing memory card transfers in an enhanced PanelView
1200 (Series F and above) terminal, you cannot copy application
files from the PCMCIA memory card to another location in the
terminal.
On a PanelView 1000e, 1200e, or 1400e terminal, after you insert the
PCMCIA memory card, you can copy application files from one
location to another. For example, you could be running an
application file from the terminal’s onboard application memory and
need to copy it to a PCMCIA memory card. If you have a PCMCIA
memory card drive on your development computer, you can remove
the card and copy its contents to the hard drive of your development
computer, where you can edit the application file in PanelBuilder
1400e software.
"
Note: The PanelView 1000e terminal has two slots, but only slot 1
is active.
These transfers are controlled by the terminal. To download or
upload an application file to or from a PCMCIA card, consult the
section later in this chapter that describes the applicable mode of
transfer.
Publication 2711E-6.17 – November 1998
5–10
Configuring PanelView Terminals
To display the Memory Card Transfer screen:
1. In the Terminal Configuration screen, choose the Transfer
Application button.
2. Select the Memory Card tab.
To transfer an application file using PCMCIA memory cards:
1. In the From panel, choose the Select Source button to select the
required source file location.
A list of the application files in the location you have selected
appear in the list box.
2. Use the arrows to scroll through the list. Highlight the application
file you want to transfer.
3. In the To panel, choose the Select Destination button to select the
destination for the application file.
4. Choose the Copy button to copy the application file from the
source location to the specified destination.
5. Choose Exit to return to the Terminal Configuration screen.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–11
Formatting the PCMCIA Card or the Onboard Flash Memory (F5)
The name of the format button is different, depending on where you
are booting from—the onboard flash memory or the PCMCIA card.
Typically, you would boot from the onboard flash memory. If you do
so, the name of the button is Format PCMCIA Card. This button on
the Memory Card Transfer Application screen allows you to
re-format a PCMCIA card that was formatted with a non-PanelView
1000e, 1200e, or 1400e partition. The card will be re-formatted with
a single application partition.
If you are booting from the PCMCIA card, the name of the button is
Format Flash Memory. This button on the Memory Card Transfer
Application screen allows you to reclaim the onboard flash memory
for application file storage.
To format a PCMCIA card or the onboard flash memory:
"
Note: Before you format the destination, make copies of application
files you need to keep. To do this, make the application file you want
to keep as the current application, and upload it from the terminal to
your computer. All data on the card or the flash memory is erased
when you format.
1. In the PanelView Terminal Configuration screen, choose Transfer
Application.
2. Select the Memory Card tab.
3. To format a PCMCIA card, be sure the card is in the PCMCIA
card socket. Choose the Format PCMCIA Card button.
To format the onboard flash memory, choose the Format Flash
Memory button.
Publication 2711E-6.17 – November 1998
5–12
Configuring PanelView Terminals
4. A message appears, prompting you to confirm the card format or
the flash memory format. Choose Yes to proceed or No to cancel
the format.
You can now transfer application files to the correctly formatted
PCMCIA card or onboard flash memory.
Erasing a Destination Partition (F4)
The Erase Destination button erases the selected partition on a
PCMCIA card that is already correctly partitioned for the PanelView
terminal, or a blank card. Note that erasing the partition means
clearing the partition of any files. Erase Destination also clears a
partition in the terminal’s flash memory if Memory Partition 1 or
Memory Partition 2 is the selected destination.
However, Erase Destination does not erase a card that has been
partitioned with a non-PanelView 1000e, 1200e, or 1400e partition.
In this situation, use the Format PCMCIA Card button to delete the
contents of the PCMCIA card in the PCMCIA card socket and
re-format it for the PanelView terminal.
To use the Erase Destination button:
A file written to the terminal’s memory will occupy space until the
memory is erased, even if the file is deleted. When memory space
begins to run out, use the Erase Destination button to clear it.
Important:
Because this process erases all data in the chosen
partition, be sure to copy any files that you want to
keep. You can download them again after the terminal
or PCMCIA memory space has been erased.
If the destination for the application file does not have enough
memory space, you can erase all data at that location.
1. Choose the Select Destination button to select the partition to
erase.
2. Choose the Erase Destination button.
3. A confirmation window appears. Select Yes or No. If you select
Yes, a progress meter is displayed that indicates the status of the
erase.
When the erase is complete, you can initiate your application file
transfer to this location by choosing Copy.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–13
Pass-Through Application File Transfers
Pass-Through file transfers, which are initiated by PanelBuilder and
are available only when the terminal is in Run mode, can be
performed over the following networks:
• DH+ and Remote I/O networks, using the PLC-5 or SLC-5/04
controller’s Pass-Through feature
• ControlNet and Remote I/O networks, using the PLC-5C
controller’s Pass-Through feature
• Ethernet and Remote I/O networks, using the PLC-5E controller’s
Pass-Through feature
The file transfer can proceed using the Pass-Through parameters of
the terminal’s current application. If there is no current application or
Pass-Through parameters, or you don’t want to use the application’s
parameters, you can change the Pass-Through parameters in File
Transfer Utility and PanelView. The File Transfer Utility and
PanelView Pass-Through parameters must match.
For Pass-Through uploads, if you want to change the current
application’s transfer parameters, see Terminal Network Setup for
Remote I/O Applications in this chapter.
For Pass-Through downloads, if you want to change the current
application’s transfer parameters or you do not have a current
application selected, choose the Transfer Setup button, and then
select the Network tab in the Transfer Setup screen.
For Remote I/O Pass-Through applications, you can change the baud
rate and the control byte.
Publication 2711E-6.17 – November 1998
5–14
Configuring PanelView Terminals
Selecting Auto Restart
You can choose between Yes and No for the Auto Restart option.
The default setting is No.
• If you choose Yes, the terminal starts executing the current
application file when the application download completes
successfully. If the downloaded application is made current, it
executes; otherwise the previously running application executes.
• If you choose No, you must also choose the Resume Run mode
button in the Application Transfer screen.
Setting Address Source
To do a Pass-Through application file transfer, select either
Application or RIO Pass-Through for the Address Source. Network
Direct does not apply to Pass-Through file transfers. If an application
is already selected, the default is Application the first time you enter
this screen. When you re-enter the screen, the values that were
previously saved, appear.
When you set the Address Source to RIO Pass-Through, the current
application file is de-selected. You cannot set the Address Source
back to Application until you select a current application.
Important:
After a successful download of an application file using
Pass-Through, the terminal automatically resets the
Address Source to Application, uses the application file
parameters, and discards the Pass-Through parameters.
• ApplicationWhen you choose Application, the terminal uses
the current application file’s RIO Pass-Through parameters for
the file transfer. If the current application file contains a
Pass-Through configuration, its values are displayed in the
Terminal Network Setup Racks and Block Transfer Files screens.
The settings in the PanelBuilder application must match the
settings in the Terminal for the application to work correctly.
• Choosing RIO Pass-Through Address
Source disables the configuration parameters for the
currently-selected application file. The default settings are
displayed, which you can change if required.
The default settings for the Pass-Through transfer are as follows:
Publication 2711E-6.17 – November 1998
PLC Type
PLC 5/25
Baud
57.6K
Rack Number
1
Word
0
Byte
Low
Module Group
0, 1
Last Chassis
Yes
Configuring PanelView Terminals
5–15
The Rack Number, Module Group, and Last Chassis parameters
enable you to assign the terminal as one of the racks already
configured in the PLC scan list. When replacing an existing
application, you don’t need to reconfigure the PLC before or after
Pass-Through Download if both application files have the same rack
configurations defined.
When you set the Address Source to RIO Pass-Through and choose
OK, the terminal validates the Address Source and saves the
Auto-Restart settings. The terminal also de-selects the current
application file to ensure that the new manual Pass-Through rack
assignment does not conflict with existing application file rack
assignments.
Now when you switch to Run mode, the File Transfer screen is
displayed automatically.
PLC Controllers Required for Pass-Through
Important:
Only specific series and revisions of PLC and SLC can
do Pass-Through downloads and uploads. The
following table lists applicable PLCs and SLCs.
Processor
Series
Revision
Valid PLC Racks
Baud Rates
SLC-5/04 (requires SLC 5/04
with OS 4.01 and the 1747-SN
Series B Scanner)
All
All
3 octal
57.6 kbps
115.2 kbps
230.4 kbps
Logix55xx via 1756-DHRIO
Module
All
—
0 – 76 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/11
All
All
3 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/15
B
N or later
1 – 3 octal
57.6 kbps
PLC-5/20
All
All
1 – 3 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/20C
PLC-5/20C15
All
All
1 – 3 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/20E
All
All
1 – 3 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/25
A
J or later
1 – 7 octal
57.6 kbps
PLC-5/30
A
B or later
1 – 7 octal
57.6 kbps
115.2 kbps
230.4 kbps
Publication 2711E-6.17 – November 1998
5–16
Configuring PanelView Terminals
Processor
Series
Revision
Valid PLC Racks
Baud Rates
PLC-5/40
A
B
E or later
B or later
1 – 17 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC–5/40C
PLC-5/40C15
All
All
1 – 17 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/40E
All
All
1 – 17 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/60
A
B
E or later
B or later
1 – 27 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/60C
PLC-5/60C15
All
All
1 – 27 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/80
All
All
1 – 27 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/80C
PLC-5/80C15
All
All
1 – 27 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/80E
All
All
1 – 27 octal
57.6 kbps
115.2 kbps
230.4 kbps
PLC-5/250
All
All
1 – 37 octal
57.6 kbps
115.2 kbps
230.4 kbps
DH+ Direct/ControlNet Direct
You can upload and download application files over a direct DH+ or
ControlNet link. File transfers over DH+ or ControlNet are initiated
by PanelBuilder or the Transfer Utility and are available in Run
mode only.
For network uploads, if you want to change the current application’s
transfer parameters, see Terminal Network Setup for DH+
Applications or Terminal Network Setup for ControlNet Applications
in this chapter.
For network downloads, if you want to view the current application’s
transfer parameters, see Terminal Network Setup for DH+
Applications or Terminal Network Setup for ControlNet Applications
in this chapter. If you want to change the current application’s
transfer parameters or you do not have a current application selected,
choose the Transfer Setup button, and then select the Network tab in
the Transfer Setup screen.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–17
For DH+ or ControlNet, you must specify communication
parameters and the terminal’s network address in
PanelBuilder—your terminal will accept those parameters by
default.
Setting Address Source
To do a DH+ Direct or ControlNet Direct transfer, you must choose
either Application or Network Direct as the Address Source. The
first time you enter this screen, the default is Application.
• Application—When you choose Application for DH+ or
ControlNet, all the configuration parameters are taken from the
currently-selected application file. This is the default setting.
• Network Direct—When you choose Network Direct, the
configuration parameters for the application file are disabled, and
you have to enter the parameters manually.
Important:
After a successful download of an application file over
DH+ or ControlNet, the terminal automatically resets
the Address Source to Application, uses the application
file parameters, and discards the Manual Address
parameters.
To select the network type for direct application file transfers:
1. In the PanelView Terminal Configuration screen, choose Transfer
Setup.
2. Select the Network tab.
3. Choose Network Direct as the Address Source.
The Network Type can be changed to ControlNet only if a
1784-KTCX or 1784-KTCS card is installed.
In the following examples, the first screen displays a ControlNet
Direct transfer. The second screen displays a DH+ Direct transfer.
Publication 2711E-6.17 – November 1998
5–18
Configuring PanelView Terminals
For a ControlNet network type, the Terminal Network Address is
a value between 1 and 99 (decimal). For some ControlNet
versions, address 1 must be assigned to a PLC.
For a DH+ network type, the Terminal Network Address is a
value between 0 and 77 (octal); the default is a 0 value. The Baud
Rate default is 57.6K.
4. Choose OK.
5. Switch the terminal to Run mode.
You can now transfer application files over the selected network.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
Selecting an Application
5–19
The terminal can store several application files. An application file
must be designated as the Current Application to run on the terminal.
An application file is made the Current Application as a result of
settings in file transfer dialogs and the state of the terminal when the
download occurs. A downloaded file is made current if:
• the Make Current option is selected (the default), or the
downloaded file has the same name as the terminal’s
currently-selected file
• the file is compatible with the terminal type and firmware version
"
Note: If a downloaded file is the only application on the terminal, it
is selected as the Current Application by default.
With the Select Application screen in PanelView, you can choose
which application to make current for uploading or running it.
Application files can be stored in several locations on the terminal,
depending on terminal and storage media type. The following table
lists the storage locations.
Terminal Type
Firmware Storage
Application File Storage Options
Enhanced Series F
and above terminal
with 2-MB SIMM
and 4-MB PCMCIA
card
The firmware resides on
Card Partition 1 of the
PCMCIA card.
The application file will reside on Card Partition 2 of the PCMCIA card. The amount of
space for application file storage depends on the size of the PCMCIA card. The firmware
will occupy approximately 1.7 MB. The remaining space can be used for application file
storage.
PanelView 1000e
The firmware resides in the
terminal’s onboard flash
memory.
The application file can reside in three locations:
• on the terminal’s onboard flash memory
• on Card Partition 1 on a PCMCIA memory card
• on Card Partition 2 on a PCMCIA memory card
The terminal memory can store application files up to 2.25MB.
If you have an application file larger than the specified terminal memory, it must be stored
on a PCMCIA card. The application file storage space available on the PCMCIA card and
the number of data partitions depends on the size and formatting of the PCMCIA card.
If the 1000e terminal is executing firmware from a PCMCIA card, memory partition 1 is
also available for file storage if the onboard firmware is erased.
PanelView 1200e
and 1400e terminal
The firmware resides in the
terminal’s onboard flash
memory.
The application file can reside in three locations:
• on the terminal’s onboard flash memory
• on Card Partition 1 on a PCMCIA memory card
• on Card Partition 2 on a PCMCIA memory card
The terminal memory can store application files up to 256K only. If you have an
application file larger than 256K, it must be stored on a PCMCIA card. The application file
storage space available on the PCMCIA card and the number of data partitions depends
on the size and formatting of the PCMCIA card.
If the 1200e or 1400e terminal is executing firmware from a PCMCIA card, memory
partition 1 is also available for file storage if the onboard firmware is erased.
Publication 2711E-6.17 – November 1998
5–20
Configuring PanelView Terminals
In the Terminal Configuration screen, choose the Select Application
button to display the Select Application screen.
The current application name and location on the terminal are shown
in the Current Application status line. The application files in the
terminal in that location are displayed in the list box. To view
application files in other locations, choose the Select Source button.
To make a file the Current Application:
1. Choose the Select Source button for the application file you want
to make current.
2. From the select list, use the Up and Down arrows to highlight the
file you want to make current. A description of the file is
displayed as you scroll through the list.
3. Choose Select Application to make this file the current
application.
4. Choose OK to save changes. The new file is now the current
application and is the one used when you switch to Run mode.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
Terminal Network Setup
for Remote I/O
Applications
5–21
You can view the rack assignments and block transfer file definitions
of the current Remote I/O application file in the Terminal
Configuration screen.
Important:
For information to be displayed on the screen, an
application must be made current (selected).
To display Rack assignments for Remote I/O:
"
In the Terminal Configuration screen, choose the Terminal
Network Setup button.
The PLC (Device) Type and baud rate at which you are
communicating are displayed at the top of the screen. To change the
baud rate, use the Baud Rate button.
Important:
When you switch the terminal back to Run mode, the
setting you specify here overrides the application file
setting. The baud rate on this screen must match the
network’s speed or the PanelView terminal will not be
able to communicate with the network.
For PanelView keypad terminals, the following Terminal Network
Setup screen appears.
Publication 2711E-6.17 – November 1998
5–22
Configuring PanelView Terminals
For PanelView touch screen terminals, the following Terminal
Network Setup screen appears.
The Rack Number, Module Groups, Last Chassis (Yes or No), and
Access (Full or Listen Only) values are displayed. Use the Prev
(Previous) and Next buttons to scroll through the entries in this
window.
To display Block Transfer assignments for Remote I/O:
"
Choose the Block Transfer Files button.
Your PLC Type, baud rate, Block Transfer File number, Rack
number, Word, High/Low Byte, File Size, Usage, and Access (Full
or Listen Only) values are displayed. Use the Prev and Next buttons
to scroll through the entries in this window.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–23
The Pass-Through Control Byte is also displayed, if it is defined in
the current application.
Terminal Network Setup
for DH+ Applications
View the terminal settings and PLC information of the current DH+
application file in the Terminal Network Setup screen.
To view the terminal network settings:
"
In the Terminal Configuration screen, choose the Terminal
Network Setup button.
Important:
For information to be displayed on the screen, an
application must be made current (selected).
The terminal network address and baud rate at which you are
communicating are displayed at the top of the screen. To change the
terminal network address, use the Up and Down arrows. To change
the baud rate to 57.6K, 115.2K, or 230.4K, use the Baud Rate button.
The default baud rate setting is 57.6K.
All nodes (devices) with which your application will communicate
are listed. The terminal network address, Device Type, and Timeout
are displayed in the window. Use the Prev and Next buttons to scroll
through the entries in this window.
Publication 2711E-6.17 – November 1998
5–24
Configuring PanelView Terminals
Terminal Network Setup
for ControlNet
Applications
You can view the terminal settings and PLC information of the
current ControlNet application file.
To view the terminal network settings:
1. In the Terminal Configuration screen, choose the Terminal
Network Setup button.
Important:
For information to be displayed on the screen,
an application must be made current (selected).
If you have a a ControlNet application with no scheduled tags
assigned, the following screen appears.
If you have a ControlNet application with scheduled tags
assigned, the following screen appears listing the nodes your
application communicates with.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–25
The terminal network address is displayed at the top of the
screen. To change the terminal network address, use the Up and
Down arrows. The baud rate cannot be changed for a ControlNet
network.
All nodes (devices) that your application will communicate with
are listed. The terminal network station address, Device Type, and
Timeout are displayed in the window. Use the Prev and Next
buttons to scroll through the entries in this window.
2. If you have a ControlNet application selected with scheduled tags
assigned, choose the Scheduled Files button to display the
configured scheduled files used by the application.
3. If you have a ControlNet application with scheduled tags
assigned, choose the Nodes button to return to the Terminal
Network Setup screen displaying the ControlNet node
information.
Publication 2711E-6.17 – November 1998
5–26
Configuring PanelView Terminals
Application Startup
The initial values of certain multistate input control objects such as
Control Selectors, Interlocked Push Buttons, and Numeric Input
objects can be assigned in PanelBuilder 1400e software. These
values are PLC input states that are initially transferred to the PLC
depending on the operation chosen in the Application Startup screen.
"
Note: All objects (tags) have initial values. Some objects have
initial states and the values associated with these states override the
initial values for these objects.
To view application start-up settings:
"
In the Terminal Configuration screen, choose the Application
Startup button to display the following screen.
Start-up Options Over Remote I/O and ControlNet (Scheduled)
By default, when an application is downloaded or made current and
the terminal is switched to Run mode, the first values written to the
PLC are the initial values. Also, after a power cycle, the initial value
or initial states values are written. When the terminal is switched
from Run to Configure to Run mode, the last state value is written.
If you choose No for Use Default Operation, the initial values or
state values are written when the terminal is in Run mode for the first
time. After a power cycle, or when switched between modes, the last
state value is written. When the terminal is switched from Run to
Configure to Run mode, the last state value is written. The default is
Yes for Use Default Operation.
When the terminal is switched from Run to Configure mode, nothing
is written.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–27
Start-up Options Over DH+, ControlNet (Unscheduled), and Other
Networks
By default, when an application is downloaded or made current and
the terminal is switched to Run mode, no initial values are written to
the PLC. As well, after a power cycle or when switching from
Configure to Run mode, no initial values are written. When the
terminal is switched from Run to Configure to Run mode, no initial
values are written.
If you choose No for Use Default Operation, initial values or initial
state values are written when run for the first time. Also, after a
power cycle, the initial value or initial states values are written.
When the terminal is switched from Run to Configure to Run mode,
nothing is written. The default is Yes for Use Default Operation.
Important:
Application Security
With DH+ or ControlNet (unscheduled)
communications, if you set the terminal to write Initial
Values, you could overwrite PLC addresses already in
use by other devices on the network. Also, it can take a
long time for the terminal to write all the values.
Use the Security screen to assign up to 16 Operator Access Codes.
Once access codes are set, an operator must sign on using the
appropriate code to view screens that have security assigned. Screen
security is assigned in the Security Screen dialog in PanelBuilder.
Important:
Any security assigned to the Application Startup screen
or to a screen triggered by the PLC Controlled Screen
option, configured in PanelBuilder, is ignored.
To assign operator access codes:
1. In the Terminal Configuration screen, choose the Security button.
2. Select the Access Codes tab.
Publication 2711E-6.17 – November 1998
5–28
Configuring PanelView Terminals
The list displays the operators and any assigned security codes.
3. Scroll through the list of operators using the Up and Down
arrows. Highlight the operator you want to assign a security code
to.
4. To set an operator’s code, enter a numeric sequence up to five
characters long. On a touch screen terminal, use the keypad on
the screen. On a keypad terminal, use the numeric keypad. On an
external keyboard, use the Backspace key to represent ←, the
Enter key to represent ↵, and the numeric keys to represent 0 to 9.
Choose Enter to set the code.
5. Assign all the required operator codes.
6. Choose OK when you are finished to save this information.
Screen Security
Screen security, even if configured in PanelBuilder, is not in effect
until the Screen Security setting is enabled at the terminal. Once
enabled, operators can access a restricted screen only by entering the
correct security code. If the code is invalid, the requested screen
won’t be displayed.
In the Security screen, select the Global tab to display the following
screen.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–29
You can enable or disable screen security for the application you are
running.
• EnableIf you enable screen security, only authorized operators
will have access to screens with screen security assigned.
• DisableIf you disable screen security, all operators will have
access to all screens, whether or not the screens have security
assigned to them. The Disable setting is the default.
Mode Switch
In the Security screen, select the Mode Switch tab to display the
following screen.
For the Software Mode Switch to operate, the terminal’s hardware
keyswitch must be in Run mode. Use the Software Mode Switch
button to enable or disable the Goto Configure Mode button, which
is displayed in an application running on the PanelView terminal.
Operators can use the Goto Configure Mode button to switch
between Run and Configure modes without using the hardware
keyswitch.
Important:
If the Software Mode Switch is set to Enable, the Goto
Configure Mode button is displayed without access
restrictions on both the Transfer Application screen and
the Major Fault window, as shown below. This may
pose a security issue, because all operators will be able
to switch between Run and Configure modes.
Publication 2711E-6.17 – November 1998
5–30
Configuring PanelView Terminals
A Goto Configure Mode button in an application running on the
PanelView terminal does not disable the terminal’s hardware
keyswitch; the terminal can still be switched from Run mode to
Configure mode, using the keyswitch or remote keyswitch (if fitted).
The following table shows the behavior of the terminal at power-up:
If the terminal is powered up with:
then the terminal powers up in:
the Software Mode Switching option
disabled
the mode indicated by the hardware
keyswitch
the Software Mode Switching option
enabled, and the hardware key switch in
Run Mode
the same mode it was in at power down
the Software Mode Switch option enabled
and the hardware keyswitch in Configure
Mode
Configure Mode
The Software Mode Switch button also lets you enable or disable the
Run Mode button on the Terminal Configuration screen.
• EnableIf you enable the software mode switch, operators can
switch the terminal from Run mode to Configure mode using the
Goto Configure Mode button. Also the Run Mode button on the
Terminal Configuration screen is enabled.
• DisableIf you disable the software mode switch, the Goto
Configure Mode button is disabled, and the Run Mode button on
the Terminal Configuration screen is disabled. The Disable
setting is the default.
Setting Time and Date
In the Terminal Configuration screen, choose the Time and Date
button to open the Time and Date screen.
For PanelView keypad terminals, the following Time and Date
screen appears.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–31
For PanelView touch screen terminals, the following Time and Date
screen appears.
Customize the time display using the Format, Show Seconds, and
Leading Digit buttons. The previous screen’s sample display shows
the time in 12-hour format, with seconds showing, and with a
leading zero before the hour.
Publication 2711E-6.17 – November 1998
5–32
Configuring PanelView Terminals
To set the time:
1. Make sure the Time screen is open.
2. On the left side of the screen, make your selections for Format,
Show Seconds, and Leading Digit. The defaults are 12-hour
Format, Yes for Show Seconds, and Zero for Leading Digit.
3. Use the Up and Down arrows to select hours, minutes, and
seconds. You must enter the time in 24-hour format.
4. Choose OK to set the terminal’s time.
The time will ‘tick over’ as you set it, but the terminal’s clock is
not set until you choose OK.
To format the Date:
1. Select the Date tab to open the Date screen.
For PanelView keypad terminals, the following Time and Date
screen appears.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–33
For PanelView touch screen terminals, the following Time and Date
screen appears.
2. On the left side of the screen, make your selections for Order,
Year Format, and Leading Digit. The defaults are MDY for
Order, 2 Digits for Year Format, and Zero for Leading Digit.
3. Enter the date in 4-digit format using the Up and Down arrows to
select Year, Month, and Day.
4. Choose OK to set the terminal’s date. The range of years is 1980
to 2043.
Terminal Response
Use the Terminal Response window to change the settings of the
following terminal functions:
• Button Audio
• Alarm Audio
• Audio Volume
• Alarm Settings
• Stuck Cell Timeout
• Screen Saver Display Intensity (1000e only)
• Screen Saver Timeout
• Terminal Display Intensity (1000e only)
Publication 2711E-6.17 – November 1998
5–34
Configuring PanelView Terminals
To open the Terminal Response window:
"
In the Terminal Configuration screen, choose the Terminal
Response button.
For PanelView 1000e terminals, the following screen appears.
For enhanced PanelView 1200 (Series F and above), and PanelView
1200e and 1400e terminals, the following screen appears.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–35
Button Audio, Alarm Audio, Audio Volume
The terminal can sound a beep whenever you choose an active touch
cell or function key. The PLC controller can also trigger this audio
indicator either directly with the PLC Controlled Audio, or through
an alarm message.
To change audio settings:
1. Disable Button Audio or Alarm Audio, or to change the Audio
Volume, choose the corresponding button or function key.
• Button AudioThe default setting is On. The terminal beeps
each time you choose a button.
• Alarm AudioThe default setting is On Both the PLC
Controlled Audio bit and alarm triggered audio can cause the
terminal’s built-in audio indicator to beep. Changing this to
Off will disable both the alarm triggered audio and PLC
Controlled Audio operation (see your PanelBuilder 1400e
Configuration Software for Windows User Manual for details).
• Audio VolumeThe default setting is High. You can change
this to Low.
2. Choose OK to save your settings.
Alarm Settings
The alarm relay can be wired to an external alarm or warning light.
You control the relay by configuring an alarm message to activate it,
or by defining a PLC Controlled Relay output bit (see your
PanelBuilder 1400e Configuration Software for Windows User
Manual for details).
You can set the number of alarm history records you want displayed
on your terminal. You can display 128, 500, 1000, 1500, or 2500
alarm history records on your terminal.
In Alarm Settings, you can also enable or disable the Clear All
button and Acknowledge All button on the Alarm History screen.
Publication 2711E-6.17 – November 1998
5–36
Configuring PanelView Terminals
To open the Alarm Settings screen:
"
In the Terminal Response screen, select the Alarm Settings tab.
For PanelView 1000e terminals, the following Alarm Settings screen
appears.
For enhanced PanelView 1200 (Series F and above), and PanelView
1200e, and 1400e terminals, the following Alarm Settings screen
appears.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–37
To enable or disable alarm relay:
"
Choose the Alarm Relay button or corresponding function key to
enable or disable the relay. The default setting is Enable.
To test the alarm relay:
1. Connect a contact device such as a bell or alarm to the terminal’s
alarm relay. See Appendices A, B, and C for relay specifications.
2. Choose the Test Relay button or corresponding function key. See
Figures 2.1, 3.1, and 4.1 for the location of the alarm relay on the
1000e, 1200e, and 1400e terminals.
3. Choose the test button (On) to energize the relay, and release it
(Off) to de-energize it. The Test Relay is inactive if the Alarm
Relay is disabled.
To set the number of alarm history records to be displayed:
"
Choose the Number of Alarm History Records button to select
either 128, 500, 1000, 1500, or 2500. The default setting is 128
alarm history records.
To enable or disable the Clear All button:
"
Choose Alarm History Clear All Button or corresponding
function key to enable or disable the button. The default setting is
Disable.
If Enable is selected, the Clear All button in the Alarm History
screen is enabled. If Disable is selected the Clear All button in the
Alarm History screen is grayed-out.
To enable or disable the Acknowledge All button:
"
Choose the Alarm History Ack. All Button or corresponding
function key to enable or disable the button. The default setting is
Disable.
If Enable is selected, the Acknowledge All button in the Alarm
History screen is enabled. If Disable is selected the Acknowledge
All button in the Alarm History screen is grayed-out.
Publication 2711E-6.17 – November 1998
5–38
Configuring PanelView Terminals
Stuck Cell Timeout
To open the Stuck Cell tab:
"
In the Terminal Response screen, select the Stuck Cell tab.
For PanelView 1000e terminals, the following screen appears.
For enhanced PanelView 1200 (Series F and above), and PanelView
1200e, and 1400e terminals, the following screen appears.
You can set the length of time a touch cell or function key can be
chosen before the terminal determines the key or cell is stuck. When
the terminal determines that a key or cell is stuck, it displays a major
fault window with the following message:
Stuck button detected
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–39
To set the Stuck Cell timeout:
"
Use the Up and Down arrows to set the amount of time from 0 to
60 seconds. A setting of 0 disables the function. The default
setting is 0.
Screen Saver Display Intensity (1000e only)
Use the Screen Saver tab to set the intensity level for the screen
saver display, and to dim or switch off the backlight. Frequent
switching off can shorten the life of the backlight. (For information
on backlight replacement, see Chapter 7, Maintaining PanelView
Terminals.) When the backlight is dimmed, you can still see the
screen saver graphic.
To set the intensity level for the screen saver:
1. In the Terminal Response screen, choose the Screen Saver tab to
display the following screen.
2. Use the Backlight Intensity Level button to cycle through the
intensity levels. You can also use the button to switch off the
backlight. The default is set at the lowest intensity level, which is
50%. To test the intensity level you have set, use the Test Screen
Saver button.
3. Set the Screen Saver Timeout. The default setting is 0, which
disables the screen saver. For details on the screen saver timeout
feature, see Screen Saver Timeout below.
Publication 2711E-6.17 – November 1998
5–40
Configuring PanelView Terminals
Screen Saver Timeout
The screen saver blanks the terminal screen when no buttons have
been chosen or no touches have been detected for a specified period
of time.
The screen saver is deactivated when the following occurs:
• Major Fault. Switch modes after a Major Fault to re-enable the
screen saver.
• Operator input, such as keypad presses, screen touches, or mode
switches.
• A fault window appears. The screen saver is deactivated while a
major fault message is displayed, but is reactivated automatically
if a minor fault message is displayed.
• An active PLC Communication Status Display is updated.
Normal operation resumes after the update is complete. If a PLC
status display window is already open and the message inside it
changes, the screen saver is not deactivated.
• The PLC-controlled screen changes.
For PanelView 1000e terminals, see Screen Saver Display Intensity
(1000e only) above for an example of a screen display.
To set the Screen Saver Timeout for PanelView 1200 (Enhanced Series
F and above), 1200e, and 1400e terminals:
1. In the Terminal Response screen, select the Screen Saver tab to
display the following screen.
2. Use the Up and Down arrows to set the length of time before the
screen goes blank and the screen saver appears. Choose from 0 to
60 minutes. A setting of 0, which is the default, disables the
screen saver.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–41
Terminal Display Intensity (1000e only)
Use the Display Intensity tab in the Terminal Response screen to
adjust the brightness of the terminal display.
To set the Terminal Display intensity:
1. In the Terminal Response screen, select the Display Intensity tab
to display the following screen.
2. Use the Backlight Intensity Level to cycle through the display
intensity levels from 50% to 100%. The default is set at the
maximum intensity level, which is 100%.
Aligning the 1200e Screen
"
You can adjust the screen alignment on the 1200e terminals.
Note: There is no user-adjustable alignment or adjustment for the
1000e or 1400e terminals.
To align the 1200e screen:
"
Choose the Align Screen button to display the following screen.
Publication 2711E-6.17 – November 1998
5–42
Configuring PanelView Terminals
"
Note: Choosing the Center Screen button on either the keypad or
touch screen terminal sets the screen alignment to its default center
position.
Aligning on a Keypad Terminal
To set the screen alignment on a keypad terminal:
1. Use the four arrow keys to center your screen. There are nine
vertical steps (including the home location) and five horizontal.
When you’ve moved as far as you can go, the key turns gray
(disabled).
2. Choose OK to save your adjustments.
Aligning on a Touch Screen Terminal
Alignment is particularly important with touch screen displays,
especially if the display will be viewed at an angle.
To align the screen on a touch screen terminal:
1. Use the Test Alignment button to line up the on-screen buttons
with the touch cell borders.
2. Use the four corners of the Test Alignment button to see if it is
correctly aligned.
3. Use the arrow keys to center or align the screen.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
Printing and Displaying
Alarm Messages
5–43
Printing
The firmware supports printing to an Epson-FX80 or compatible
printer, or an HP LaserJet or compatible printer. The firmware also
determines the best fit for your printout to a page. You can print:
• application screens
• alarms displayed in both the Alarm Status and History screens
• a log of alarm messages
When printing current alarm messages on an HP LaserJet or
compatible printer, the alarm messages are stored in the HP LaserJet
or compatible printer and print only when the buffer is full. If the
power source goes down or if the printer is reset, all stored alarm
messages are lost.
To select printer type and options:
1. In Terminal Configuration, choose the Printer Configuration
button to display the Printer Type screen.
For PanelView keypad terminals, the following Printer Type
screen appears.
Publication 2711E-6.17 – November 1998
5–44
Configuring PanelView Terminals
For PanelView touch screen terminals, the following Printer Type
screen appears.
2. Choose the Printer button to select the Epson-FX80 or compatible
printer, which is the default, or the HP LaserJet or compatible
printer.
3. Choose the Layout for Screen Printing button to select Portrait or
Landscape. For the Epson-FX80 or compatible printer, the default
is Portrait. For the HP LaserJet or compatible printer, the default
is Landscape.
4. Choose the Paper Size button to select the North American
standard Letter size, which is the default, or the European
standard A4 size.
To set up printer communications:
1. In the Printer Configuration screen, select the Setup tab .
For PanelView keypad terminals, the following Setup screen
appears.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–45
For PanelView touch screen terminals, the following Setup screen
appears.
The default settings for the printer, as displayed in the Setup
screen, are: 8 for Data Bits, 1 for Stop Bits, None for Parity,
Hardware for Handshake, 9600 for Baud Rate, On for Auto Line
Feed, and On for Auto Form Feed.
2. To change the default settings, choose the appropriate button or
corresponding function key.
3. When the desired values have been configured, choose OK.
Refer to your printer manual for printer settings.
Publication 2711E-6.17 – November 1998
5–46
Configuring PanelView Terminals
Print Priorities
If you try to print more than one report, screen, or alarm message at a
time, the terminal will print in order of priority, saving the other print
jobs in a queue. The following table shows the size of the queue
allotted for each type of print job for the print priorities assigned.
Print priority
Print job
Number of print jobs that can be queued
1
Screen print
none
2
Alarm status report
1
3
Alarm history report
1
4
Alarm messages
21
Printing Screens from the Terminal
Screen print requests are ignored if the printer is already printing a
screen. For PLC-controlled screen prints, the PLC can be informed
that the printer is busy when it sends the print message. To do this, in
PanelBuilder software, enable Screen Print Active to PLC control.
For details, refer to your PanelBuilder 1400e Configuration Software
for Windows User Manual.
Operators can manually initiate screen prints by choosing the Screen
Print Button object. The PLC can also request screen prints.
Formatting Reports
Each report can start on a new page. Each report (except the Alarm
Message printout) starts with a title, including the time and date of
printing.
To disable form feeds:
"
In the Printer screen, select Off for Auto Form Feed.
Alarm messages are printed as the alarms are reported. The first
alarm message that occurs after switching to Run mode begins the
Alarm Message report. The Alarm Message report is preceded by a
form feed, but following that, the alarm messages print one to a line,
without page breaks or form feeds.
Printer Errors
Printer errors cannot be directly indicated to the terminal. The
terminal can detect a printer error only if the hardware or software
handshaking is enabled and the appropriate serial lines are connected
from the printer to the terminal. When handshaking is enabled, the
printer signals the terminal to stop sending characters if the printer is
switched offline, the internal buffers are full, or the paper is jammed.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–47
If the error persists for more than 45 seconds, an error message is
posted in a Minor Fault window. When the error is corrected, the
terminal continues to send characters to the printer.
Check that your printer is connected properly by choosing the Print
Test Page button in the Printer Configuration screen.
Important:
When you use a serial printer, you need to construct
your own cable. Use the pinout in Figure 2.12 (for
1000e), Figure 3.12 (for 1200e), or Figure 4.9 (for
1400e) to construct the terminal end of the cable. Pin 4
(for 1000e) or pin 20 (for 1200e and 1400e) detects the
signal indicating whether the printer is on or offline
when using hardware handshaking. Consult your printer
manual for the pinout at the printer end of the cable.
Displaying Alarm Messages
You can display alarm messages on a Dataliner display. PanelView
1000e, 1200e, and 1400e terminals, with the current version of
firmware installed, support the DL10 (A-B Catalog Number
2706-A41J), DL20 (A-B Catalog Number 2706-B21J), and DL50
(A-B Catalog Number 2706-F11J).
If you want to clear the alarms displayed on the Dataliner, you must
trigger an alarm message that contains only spaces. The message can
contain one or more spaces. For information on how to create
messages, see Chapter 10, Creating Messages, in the PanelBuilder
1400e Configuration Software for Windows User Manual.
To select printer type and options:
1. In the Terminal Configuration screen, choose the Printer
Configuration button to display the Printer Type screen.
2. Choose the Printer button to select Dataliner Message Display. The
printer options (Layout and Paper Size) on the screen are grayed-out.
For PanelView keypad terminals, the following Printer Type
screen appears.
Publication 2711E-6.17 – November 1998
5–48
Configuring PanelView Terminals
For PanelView touch screen terminals, the following Printer Type
screen appears.
To set up Dataliner communications:
1. In the Printer Configuration screen, select the Setup tab.
For PanelView keypad terminals, the following Setup screen
appears.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–49
For PanelView touch screen terminals, the following Setup screen
appears.
The recommended settings for the firmware’s Setup screen are:
8 for Data Bits, 1 for Stop Bits, and None for Handshake. For
Parity, Baud Rate, DL Number of Lines, and DL Characters Per
Line, configure the settings in the Setup screen to match the
settings defined for the Dataliner you are using.
2. To change the settings for Data Bits, Stop Bits, Parity, Handshake,
Baud Rate, DL Number of Lines, and DL Characters Per Line,
choose the appropriate button or corresponding function key.
3. When the desired values have been configured, choose OK.
Refer to your Dataliner manual for more information.
Publication 2711E-6.17 – November 1998
5–50
Configuring PanelView Terminals
Terminal Diagnostics
Use the Terminal Diagnostics screen to perform terminal diagnostics
or to display the number of hours you have been logged on.
To display the Terminal Diagnostics screen:
"
Choose the Terminal Diagnostics button or the corresponding
function key.
Performing Terminal Diagnostics
Select the System Tests tab to display the screen below. The screen
shown is for the 1000e and 1400e terminals, which do not have the
Degauss option. Only the 1200e terminal has the Degauss option.
• Application ChecksumTests the terminal’s current application
file only. A meter displays the results of the checksum test as it
progresses. It reports Pass if no checksum error is detected in the
terminal’s current application file, and Fail if a checksum error
occurs. The checksum test is disabled if there is no current
application.
• DegaussDemagnetizes the terminal screen and is specific to
1200e terminals. Your terminal degausses automatically on every
powerup and at midnight.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–51
• BatteryTests the battery.
• Tests the battery-backed RAM. If the terminal loses
power during the test, any retained data and configuration mode
parameters are corrupted and defaults for the corrupted data are
restored.
• Touch CellsFor a touch screen terminal. Choose the Touch
Cells button to display the following screen.
The Touch Cell test lets you test 119 touch cells to identify those
that are difficult to activate or inoperable. The 120th cell is
occupied by the OK button, which exits the screen.
Test each touch cell by touching it. A number appears on each
button you touch, displaying the number of times you have
touched it. If the number of times you have touched the button
equals the number that appears in the button, the touch cell is
working. If you find any buttons inoperable or difficult to
activate, or if the number displayed is not equal to the number of
touches, contact your Allen-Bradley Sales Representative.
• Function KeysFor a keypad terminal. When you choose the
Function Keys (F4) button from the Terminal Diagnostics screen,
the following screen appears.
Publication 2711E-6.17 – November 1998
5–52
Configuring PanelView Terminals
Test each key by touching it. If the key is working, the
corresponding key will appear to be touched on the screen. F21 is
the exit button. If you find any keys difficult to activate or
inoperable, contact your Allen-Bradley Sales Representative.
Hours Logged
Select the Hours Logged tab to display screens for the PanelView
1000e or the 1200e/1400e terminals. The screen for Hours Logged
differs depending on the PanelView terminal you are using.
For PanelView 1000e terminals, Hours Logged tracks the number of
hours of operation for the terminal and the accumulated backlight
time. This information allows you to track the total power-on time
and to schedule backlight replacement. For information on backlight
replacement, see Chapter 7, Maintaining PanelView Terminals.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–53
You only reset the hours for the backlight time after you change the
backlight.
To reset the hours for the backlight time:
"
Choose the Reset Accumulated Backlight Time button or the F1
function key. A confirmation message is displayed, as shown in
the following example.
For PanelView 1200e/1400e terminals, Hours Logged tracks the
number of hours of operation for the terminal (see figure below).
This information allows you to track the total power-on time.
Publication 2711E-6.17 – November 1998
5–54
Configuring PanelView Terminals
Restoring Defaults
To open the Restore Defaults screen:
"
In the Terminal Configuration screen, choose the Restore
Defaults button.
For PanelView keypad terminals, the following Restore Defaults
screen appears.
For PanelView touch screen terminals, the following Restore
Defaults screen appears.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–55
To cause the selected application to write out its initial values:
"
"
Choose the Load Application Initial Values button. This allows
the selected application to write out its initial values on the next
entry to Run mode.
Note: This button is disabled if a current application has not been
specified.
To restore the terminal configuration defaults:
"
Choose the Load Terminal Configuration Defaults button.
The default values are restored for the following screens:
• Transfer Setup
• Application Startup
• Security
• Time and Date
• Terminal Response
• Printer
• Align Screen
"
Upgrading Firmware
Note: If an application is currently selected, the network
communication Baud Rate and terminal network address will be
retrieved from the application file and stored in the terminal’s
parameters.
To open the Upgrade Firmware screen, choose the Upgrade
Firmware button in the Terminal Configuration screen.
For PanelView keypad terminals, the following Upgrade Firmware
screen appears.
Publication 2711E-6.17 – November 1998
5–56
Configuring PanelView Terminals
For PanelView touch screen terminals, the following Upgrade
Firmware screen appears.
"
Initiate Serial TransferA serial firmware upgrade is initiated
at the development computer using the serial transfer utility
provided. (For details on how to install the Serial Firmware
Upgrade Utility, see Appendix D.) The serial port is set
automatically so you don’t need to configure it.
Important:
You must be in this screen, not the Serial
Transfer Application screen, when you initiate a
serial firmware upgrade.
• Firmware Upgrade via PCMCIA memory cardInsert the
firmware upgrade card and choose the Upgrade button. The
terminal will reset and load the new firmware into the terminal’s
extended system memory (Flash). The terminal automatically
reboots when you eject the PCMCIA memory card. The terminal
automatically re-starts in Configure mode and displays the
Terminal Configuration screen.
Important:
Publication 2711E-6.17 – November 1998
The firmware upgrade program reformats and
repartitions the terminal’s onboard flash
memory. If it contains a data partition with
application files, the upgrade program may erase
it, in which case a message is displayed that
indicates this. You will be able to reject the
reformat if you need to upload or back up your
application files. If you accept the reformat, all
data at that location is cleared.
Configuring PanelView Terminals
Terminal Information
5–57
To display information about your system, choose the Terminal
Information button on the Terminal Configuration screen.
This screen displays:
• the current application file name
• the network type of the current application
• the size of the current application file
• the date you last modified the current application file
• any application file comments from the Application File
Comment field of the Terminal Setup dialog in PanelBuilder
software. For details, refer to your PanelBuilder 1400e
Configuration Software for Windows User Manual.
• the supported communication networks
• the amount of application file storage space (in memory and on
Card Partitions 1 and 2). You can use this information before you
do any downloading.
Publication 2711E-6.17 – November 1998
5–58
Configuring PanelView Terminals
Fault Conditions
There are two types of faults that can occur during normal
operation—major and minor faults. As well, you could encounter
mistakes or system errors, and three types of operational messages
that indicate a problem or provide status information. See Chapter 8,
Troubleshooting PanelView Terminals, for a list of major and minor
fault messages and mistake messages.
Major Faults
If the terminal detects a major fault, it enters Major Fault mode and
displays a message in the Major Fault window. The terminal cannot
control or monitor PLC functions while in Major Fault mode.
A Major Fault prevents further terminal operation in Run mode. The
terminal stops executing the application, the current application
screen is frozen, printing stops, the alarm relay and beeper are
disabled, and any application file transfers stop.
To clear a major fault:
"
Switch to Configure mode or cycle power. A Major Fault in
Configure mode can be cleared if it does not impede
configuration operations once the message is acknowledged.
Important:
If the Software Mode Switch is set to Enable, the Goto
Configure Mode button is displayed on the Major Fault
window without access restrictions, as shown below.
This may pose a security issue, because all operators
will be able to switch between Run and Configure
modes.
If the Software Mode Switch is disabled, the Goto Configure Mode
button will not be displayed on the Major Fault window, as shown
below.
Publication 2711E-6.17 – November 1998
Configuring PanelView Terminals
5–59
While the terminal is in Major Fault mode, it appears as a faulted
rack to the host PLC (Remote I/O only). You can design your PLC
program to monitor the rack fault bits that correspond to the rack
assignments of the terminal, and to respond whenever these bits
indicate that the terminal isn’t operating or communicating properly.
See your PLC and I/O scanner user’s documentation for details on
how to use the rack fault bits.
Minor Faults
If the terminal detects any minor faults, it disables normal input entry
and displays a message in the Minor Fault Window, for example:
To clear a minor fault:
"
Choose the Clear button to resume normal operation.
The Clear button temporarily overrides the function previously
assigned to the associated function key or touch cells. Minor
faults do not affect PLC communications.
Mistakes
A Mistake is an operator-initiated, minor error or illegal operation.
For example, if the operator requests that the terminal display a
screen currently being displayed (using a Goto Screen Button), the
following message appears in a Mistake window.
Requested screen is already displayed
Mistake messages must be acknowledged before any further screen
operations occur. Acknowledged Mistakes are then removed from
the screen.
Publication 2711E-6.17 – November 1998
5–60
Configuring PanelView Terminals
System Errors
Any system errors the terminal detects are logged to the System
Error window.
If a System Error appears, note the error message and contact your
Allen-Bradley Sales Representative.
Terminal Messages
Publication 2711E-6.17 – November 1998
Messages keep the operator informed about the status of the
operation when the application is running. Messages are displayed in
windows on the terminal screen. You can create three types of
messages in the Messages editors in PanelBuilder software:
• Alarm MessagesThese alert the operator to problems in the
process. Each alarm message can be equipped with special
options to sound an audio alarm, energize an alarm relay, and
print the alarm message.
• Information MessagesThese inform the operator about
operational status and provide prompts, instructions, or warnings.
• Local MessagesThese appear in the Local Message Display
object. Like information messages, local messages inform the
operator about the status of an operation or provide prompts or
instructions.
Verifying PanelView Terminal
Operation
This chapter describes how to verify that your PanelView 1000e,
1200e or 1400e terminal is operating and communicating correctly.
Information is also provided on connecting a PLC to the terminal.
Testing the PanelView
Terminal
To test your terminal:
1. Set the Mode Select Keyswitch to Configure mode.
2. Choose Terminal Diagnostics from the Terminal Configuration
menu. The Terminal Diagnostics screen is displayed.
3. Run the tests. Details of the Terminal Diagnostics are in Chapter 5
of this manual.
The remainder of this chapter discusses testing your terminal with an
application file. If you or your developer have already created an
application with PanelBuilder software, use that file. If you are
installing a new terminal and are new to PanelBuilder software as
well, you might not have an application file ready to run on the
terminal. If so, use the applicable DEMO file located in the file
\AB\PB1400e\DEMO.
"
Note: DEMO files require more than 256K of user memory. These
files will fit in the 1000e terminal. For 1200e/1400e terminals, we
recommend you download them to a PCMCIA card.
For DH+ or ControlNet, you must verify that the station number of
the terminal is correct. The terminal must have a valid application.
Then:
1. Set the Mode Select Keyswitch to Run mode.
2. Using 6200 software, enter the Who Active command. Versions
5.1 and lower of the 6200 software will show the device type as
question marks (???). Newer PLC Programming software will
identify the terminal as PVe. The application name is also
displayed with the terminal station number.
Publication 2711E-6.17 – November 1998
6–2
Verifying PanelView Terminal Operation
Downloading the
Application File
Your PanelBuilder software includes a DH+ application
demonstration file for both the touch screen and keypad terminals. If
your system does not yet include an application file to download and
test, use the DEMO file for your terminal.
"
Note: The PanelBuilder software includes a demo that you can run
for the 1000e and 1400e terminals only. To run demos for the 1200e
terminal, you need to change the Terminal Type (from the Terminal
Setup screen in PanelBuilder) before downloading.
Matching Communications Settings
Before you can serially download or upload, the communication
settings on the terminal and File Transfer Utility must be the same.
The factory settings of the terminal and File Transfer Utility are
matched, so if you have not changed them, download the DEMO or
your other application file now.
To reset the terminal to its default settings:
1. Choose Restore Defaults from the Terminal Configuration screen.
2. Choose Load Terminal Configuration Defaults. To manually
change defaults, refer to Chapter 5 of this manual.
All configuration parameter defaults will be reset, not only the
file transfer parameters.
To reset the parameters in your PanelBuilder development computer,
refer to the PanelBuilder 1400e Configuration Software for Windows
User Manual.
Download Procedure
Once communication settings are matched, you can start the
download procedure as follows:
1. Using the Upload/Download cable, connect the terminal to the
development computer.
2. Set the Mode Select Keyswitch to Configure mode.
3. In the Terminal Configuration screen, choose Transfer
Application.
4. In the development computer, choose an application file for
downloading, and start the download. Choose your own
application file if you have one. If not, select the applicable
demonstration file for your terminal type from the files packaged
with PanelBuilder software.
Publication 2711E-6.17 – November 1998
Verifying PanelView Terminal Operation
6–3
For details on downloading an application file, refer to the
PanelBuilder 1200/1400e Transfer Utility User Manual.
Running the Application
File
Set the keyswitch at the rear of the terminal to Run. You can also use
the Run mode button (if enabled). For details, see Mode Switch in
Chapter 5 of this manual.
!
Important:
ATTENTION: Do not connect a PLC to the terminal.
You do not have a functional application file, and you
are not ready to monitor a PLC.
When the PLC is not connected, the terminal displays a
message indicating:
Remote I/O: PLC communication lost.
For DH+, the corresponding message is:
Unable to communicate with remote station.
You can safely ignore these messages at this stage.
If the power-up screen for your application file appears on your
terminal, the file has been successfully downloaded. (If you are
downloading a DEMO file, the Main Menu is displayed on the
terminal.)
Try some or all the items in your application to ensure the screens
and buttons are working.
Connecting the PLC
Controller
When the screens and buttons are functioning as expected, connect a
programming terminal to the PLC controller and monitor the PLC’s
Data Table.
!
ATTENTION: Disable all other I/O racks or modules
that could be affected by the PanelView terminal.
The PanelBuilder 1400e Configuration Software for Windows
installation includes file 2711E. Download this PLC application file
to your PLC if:
• you are using one of the DEMO files as your application file, and
• your PLC is a PLC-5, or SLC-enhanced
Publication 2711E-6.17 – November 1998
6–4
Verifying PanelView Terminal Operation
If you are using another PanelBuilder application file, you will have
to use your own PLC application program for whatever PLC you are
using.
At this stage, connect the terminal to the PLC, but be sure the PLC
isn’t controlling any machines or processes.
Refer to your scanner and PLC manuals for information on how to
create scan lists that include all rack assignments for the PanelView
terminal.
Testing Retentive Objects
When all PLC-controlled machines and processes have been
disabled, you can set both the PLC and terminal to Run mode, if you
haven’t already done so. Observe each object carefully if you’re
using any retentive input objects. Switch the terminal off and on
again, and switch it to Configuration mode and back to Run mode.
Watch the input addresses for each retentive object to ensure the
values are initialized so the program responds safely.
Testing the Whole System
Once you’ve checked all PLC values and determined that all objects,
windows, and PLC-controlled functions communicate correctly with
the PLC, you’re ready to set the PLC and terminal to Run mode and
test your application file.
!
ATTENTION: If the PLC program can control any
specific machine action or process that could result in
unsafe or critical operation, temporarily disable these
specific operations. Keep people at a safe distance from
any PLC-controlled machine. Finally, make sure
emergency stop buttons are easily accessible during
control system testing.
Step through each screen in the application file to ensure valid states
and values are displayed. Test each object individually to ensure the
PLC system responds as expected. Use the programming terminal to
monitor what happens inside the PLC as you use each object, and
then change the values within the PLC to see how the terminal
responds.
Power down, then power up the terminal, and switch the terminal to
Configure mode and back to Run mode. Remove and re-apply power
to the PLC separately, and to the entire control system to ensure that
the system re-initializes as expected.
Your PanelView terminal is now ready for use.
Publication 2711E-6.17 – November 1998
Maintaining PanelView
Terminals
Maintaining Your
PanelView Operator
Terminal
Follow the instructions below to keep your PanelView 1000e, 1200e,
or 1400e terminal operating at peak efficiency.
Cleaning
Cleaning the Touch Screen
To clean the touch screen, use ethyl alcohol (ethanol) on a cotton
gauze pad. This is more efficient than isopropyl alcohol (which
leaves a slight residue upon first application), and safer than methyl
ethyl ketone (MEK). MEK is harmless to the touch screen, but
repeated applications will discolor the bezel if the paint surface is
broken or scratched.
Cleaning the Keypad
To clean the front of the keypad terminal, use a 50% solution of
alcohol (ethanol or isopropanol) in water on a cotton gauze pad or
soft cotton cloth. You can also use a mild soap or detergent and
warm water, but avoid abrasive cleaners.
Cleaning the Enclosure
Use a 50% solution of alcohol (ethanol or isopropyl) in water on a
cotton gauze pad or soft cotton cloth to clean the enclosure.
Important:
The cleaning solution should be applied to the cloth
only, not directly to the enclosure.
Important:
Internal components can be damaged if fluids get into
the enclosure.
CRT Intensity (1200e and 1400e)
The lower the intensity at which the cathode ray tube (CRT)
operates, the longer its life. You can control the intensity of your
screen with the color contrast and brightness controls on the
terminal.
Publication 2711E-6.17 – November 1998
7–2
Maintaining PanelView Terminals
Changing the Fan Filter (1200e and 1400e)
Clean the fan filter whenever it appears to be clogging up. Remove
the filter cover from the back of the terminal by popping it free of its
plastic side clips and clean it by:
• removing the dust with a vacuum cleaner
• washing with warm water and soap. Be sure the filter is dry
before you replace it
• the filter is made of flame-retardant urethane foam 0.13 inches
(3.3 mm) thick, and measures 3.64 inches by 3.54 inches (92.5 by
89.9 mm). Replace unusable filters with part number 09362-M/45
from Hitachi or Qualtek Electronics.
Degaussing the CRT (1200e and 1400e)
If an external magnetic field (such as an electric motor starting up)
occurs near a color terminal, the CRT may retain some residual
magnetic effect, which could affect the clarity of the display.
Degaussing removes any such residual magnetism by totally
demagnetizing the CRT. Automatic degauss occurs each time ac
power is re-applied to the terminal.
For the 1200e terminals, degauss occurs also at midnight (according
to the terminal’s system clock) daily. You can also degauss the 1200e
color terminal manually in Configure mode. See Chapter 4 of this
manual for more information.
If the terminal is powered by an isolated power source, be sure the
line transformer can handle the surge that occurs while the terminal
degausses. See Appendices B and C for degauss specifications.
Avoiding Strong Magnetic Fields (1200e and 1400e)
Because the terminal display contains a CRT, the presence of strong
magnetic fields near the terminal will distort the image on the screen.
Avoid magnetic fields stronger than 80 milligauss at the front surface
of the terminal.
Publication 2711E-6.17 – November 1998
Maintaining PanelView Terminals
7–3
Backlight Replacement (1000e)
It may be necessary to replace the backlight after 10000 hours of
backlight operation. For the procedure on how to replace the
backlight, see the Installation Data Sheet that is included in the
Backlight Replacement Kit (A-B Catalog Number 6189-NL2). To
prolong the life of the backlight, use the screen saver and reduce the
backlight intensity.
After you change the backlight, you must reset the hours for the
backlight time. For details, see Hours Logged in Chapter 5 of this
manual.
You can check the number of hours that the terminal has been in
operation by selecting Terminal Diagnostics from the Terminal
Configuration screen. Then select the Hours Logged tab. For details,
see Hours Logged in Chapter 5 of this manual.
Publication 2711E-6.17 – November 1998
Troubleshooting PanelView
Terminals
This chapter describes how to diagnose and solve operational
problems of a PanelView 1000e, 1200e, or 1400e terminal. To help
solve PanelBuilder software problems, refer to your PanelBuilder
1400e Configuration Software for Windows User Manual and the
PanelView 1200/1400e Transfer Utility User Manual.
For PanelView 1000e terminals, if your screen becomes darkened,
either the screen saver has been switched on or the backlight has
been switched off. If you notice uneven intensity, the backlight may
need to be replaced. For information on backlight replacement, see
Chapter 7, Maintaining PanelView Terminals.
Verifying Configuration
Settings
To view the terminal network settings, press the Terminal Network
Setup button on the Terminal Configuration screen. The settings
displayed for RIO, DH+, and ControlNet are those of the current
application.
Major Fault Messages
The following table lists the most common major fault messages that
can occur on a PanelView terminal.
Major Fault Message
Cause
What To Do
Application file corrupted.
The application file has become corrupted
(checksum failure) or invalid data was read
from it.
Try downloading the file again.
Application file is not compatible.
The application file requires a later version
of firmware.
Install the correct version of firmware.
Application file not valid.
The terminal cannot locate the current
application file. It may have been deleted or
was on a PCMCIA card that has been
removed.
Check that the application file is still present.
Communication Subsystem Failure. See User
Manual for more information.
A ControlNet application cannot locate the
ControlNet communications adapter.
Problem with communication drivers or
hardware.
Check that the ControlNet communications
adapter is installed correctly.
Cycle power, switch modes, check that
appropriate communication hardware is
installed.
Check communication card for proper
switch settings.
Error erasing memory card.
The memory card could be faulty.
Try reformatting the memory card using the
Format Destination button in the Memory
Card Transfer Application screen. If this
does not work, replace the memory card.
Publication 2711E-6.17 – November 1998
8–2
Troubleshooting PanelView Terminals
Major Fault Message
Cause
What To Do
Error writing to memory card.
The memory card could be faulty.
Try reformatting the memory card using the
Format Destination button in the Memory
Card Transfer Application screen. If this
does not work, replace the memory card.
File Transfer failed. Application file corrupt.
File transfer failed.
Try downloading the file again.
Invalid file I/O.
An error has occurred accessing the
memory card. The card could be faulty.
Try reformatting the memory card using the
Format Destination button in the Memory
Card Transfer Application screen. If this
does not work, replace the card.
No current application file selected.
The terminal was switched to Run mode
with no current application file selected.
Return to Configure mode and select a
current application file. See Chapter 5 of
this manual for more information.
No Post-release applications allowed.
The terminal is running pre-release
firmware.
Upgrade the terminal to the official release.
No Pre-release applications allowed.
Attempting to run an application file created
with a pre-release version of software.
Upgrade PanelBuilder to an official release
and regenerate the .pvd file.
Not enough graphics memory to display this
screen.
The current screen contains too many
objects (typically, there are too many
bitmaps).
Edit the screen to reduce the number of
objects, or, if there are large bitmaps on the
screen, break them into several smaller
ones.
Not enough memory to display bitmap on the
screen.
The current screen contains a bitmap which
is too large for the available memory.
Edit the screen to remove the bitmap or use
a smaller bitmap.
Not enough memory to display this window.
Terminal does not have enough memory to
display the pop-up window (information
window, alarm window).
Try rebooting the terminal.
Contact your Allen-Bradley Sales
Representative to report the error.
Not enough RAM installed to display this screen.
Too many objects.
Edit the screen to reduce the number of
objects. Redesign the screen (break into
smaller screens if necessary).
Partition not on memory card boundaries. Press
Format PCMCIA Card button to format the entire
card.
Memory card was incorrectly partitioned.
Try reformatting the memory card using the
Format Destination button in the Memory
Card Transfer Application screen. If this
does not work, replace the memory card.
Stuck button detected.
A touch cell or keypad button has been
pressed for longer than the Stuck Button
Timeout setting allows.
Restart the terminal. If this problem occurs
repeatedly due to an operator holding the
button down for too long, increase the Stuck
Button Timeout setting in the Configuration
menu.
If a button or cell is permanently stuck, call
your Allen-Bradley Sales Representative.
Terminal can’t keep up with activity.
The terminal is overloaded with writes to the
PLC. This is most likely to occur on a screen
change.
Reduce the number of objects on the
screen that write to the PLC or use a
PLC-controlled screen change.
The terminal does not contain the necessary
communication card to execute this application.
A ControlNet application cannot locate the
ControlNet communications adapter.
Check that the ControlNet communications
adapter is installed correctly.
Check communications card for proper
switch settings.
Check that you have the 1784-KTCS card in
order to work with scheduled files.
Publication 2711E-6.17 – November 1998
Troubleshooting PanelView Terminals
Major Fault Message
Cause
What To Do
There has been a communication failure. PLC
write failed.
Too many objects on the screen are writing
values to the PLC.
Reduce the number of objects on the
screen that write to the PLC or use a
PLC-controlled screen change.
Watchdog test failed.
Watchdog circuit cannot reset the machine.
Contact your Allen-Bradley Sales
Representative.
Major Fault Message
Cause
What To Do
Touch Controller hardware failure.
Touch controller hardware failed.
Contact your Allen-Bradley Sales
Representative if the touch screen is
responding incorrectly.
Touch Controller not responding.
No response from the touch controller.
Contact your Allen-Bradley Sales
Representative.
8–3
For 1000e and 1400e Touch Terminals Only:
Minor Fault Messages
The following table lists the most common minor fault messages that
can occur on a PanelView terminal.
Minor Fault Message
Cause
What To Do
Alarm message not sent to PLC — too many
outstanding requests.
There are too many messages in the
message queue to the PLC.
Reduce the rate at which alarms are
generated, or check that the PLC is
retrieving messages.
Battery test failed. User RAM will be lost on power
down.
The battery for application file memory has
failed.
When power is disconnected, retained
valuesincluding configuration
parameters, retentive data, and alarm
historywill be lost.
Contact your Allen-Bradley Sales
Representativeservicing is required to
replace the battery.
Expression attempted to divide by zero.
An operation in the program running on the
terminal is dividing by zero.
Check the expressions in your application,
to ensure that none are dividing by zero.
Expression contains an invalid tag value.
An out-of-range or badly-formatted value at
the PLC. This is most frequently the result of
an invalid BCD value.
Check that the PLC program is sending
valid values to the terminal.
Expression evaluated to an out-of-range value.
An operation in the program running on the
terminal is assigning too large a value to the
local variable type.
Check the expressions in your application,
and change the local variable’s type to one
that will accommodate the value.
Expression caused divide by zero.
Expressions have been created that use
division, and the denominator is a tag. The
fault message is displayed if the expression
is displayed on the first screen when the
application starts up, or the expression is
assigned to alarms or global PLC I/O
controls.
Clear the fault message.
Invalid Application Startup screen.
Application file specifies a non-existent
screen number as the Application Startup
screen.
Reprogram the application file and assign a
valid screen number as the Application
Startup screen.
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
Publication 2711E-6.17 – November 1998
8–4
Troubleshooting PanelView Terminals
Minor Fault Message
Cause
What To Do
Invalid decimal point position.
The value at the PLC Controlled Decimal
Point Position tag address is not valid.
Ensure the value at the PLC Controlled
Decimal Point Position is between 0 and 16.
Invalid screen.
The PLC has selected a non-existent
screen number.
Reprogram the PLC or the application file.
Memory card containing application file has been
ejected. Current application file has been
deselected.
The current application is on the PCMCIA
card and the card is ejected.
Replace the card and re-select the
application.
Memory card format failed. Please try again.
The memory card could be faulty.
Try reformatting the memory card using the
Format PCMCIA Card button in the Memory
Card Transfer Application screen. If this
does not work, replace the memory card.
PCMCIA card does not contain a valid firmware
upgrade.
Invalid firmware on the card.
Contact your Allen-Bradley Sales
Representative to get the current version of
firmware for the terminal.
Time/Date received from PLC is invalid.
The value of one or more of the Time and
Date from PLC tag address is not valid.
Check that the PLC program is sending
valid values to the terminal.
The Goto Configure Mode button is disabled.
The feature is disabled in the Security Mode
Switch screen.
Switch to Configure mode using the terminal
hardware keyswitch. On the Terminal
Configuration screen, select Security. On
the Security screen, select the Mode Switch
tab. Use the Soft Mode Switch button to
select Enable.
Screen printing not allowed with 7 data bits.
The firmware does not allow 7 data bits for
screen printing.
On the Terminal Configuration screen,
select Printer Configuration. On the Printer
Configuration screen, select the Setup tab.
Press the Data Bits button or its
corresponding function key to change the
Data Bits setting to 8.
Mistake Messages
The following table lists the most common mistake conditions that
can occur on a PanelView terminal.
Mistake Message
Cause
What To Do
Alarm History print ignored—a previous request is
already queued.
You have requested a print-out of the alarm
history while one is printing.
Wait for the alarm history print-out to
complete before requesting another.
Alarm message print ignored—queue is full of
previous requests.
The terminal is sending alarm messages to
the printer faster than the printer can
process them.
Decrease the rate at which alarms are
generated. Use higher baud rate to printer.
Alarm Status print ignored—a previous request is
already queued.
You have requested a print-out of the alarm
status while one is printing.
Wait for the alarm status print-out to
complete before requesting another.
Control Byte location does not lie within the
specified module group range.
The module group chosen in the Control
Byte is outside of the rack definition.
Expand the rack definition to include the
Control Byte module group, or change the
Control Byte location to be within the
specified module group range.
Current operation failed. Memory card is
write-protected.
The memory card is write-protected.
Remove write-protection (move the tab)
from the memory card.
Publication 2711E-6.17 – November 1998
Troubleshooting PanelView Terminals
8–5
Mistake Message
Cause
What To Do
Cursor Control Value corresponds to a skipped
state value.
The value of the Cursor Control matches a
skipped state in the cursor list.
Check that the state values for the cursor
list are configured correctly and the PLC
program is using the correct values.
Cursor Control Value does not correspond to a
configured state value.
The value of the Cursor Control does not
match any of the configured cursor list state
values.
Check that the state values for the cursor
list are configured correctly and the PLC
program is using the correct values.
Ensure printer is ONLINE.
The printer could be offline.
Check that the serial printer cable is
properly connected and the printer is online.
Increment/Decrement button limit has been
reached.
Increment/Decrement buttons can’t be
incremented or decremented beyond their
configured limits.
Check that the button limits have been
correctly configured in PanelBuilder.
Invalid PLC Type and Baud Rate combination.
The selected PLC type does not support the
selected Pass-Through baud rate.
Ensure Baud Rate and PLC Type are
compatible in the RIO Pass-Through
transfer setup.
Invalid PLC Type and Rack Number combination.
The selected PLC type does not support the
selected rack number.
Ensure the PLC Type and Rack Number are
compatible for the RIO Pass-Through
transfer setup.
Memory card has changed since file was loaded.
Please replace original card.
The memory card containing the currentlyselected application has been removed so
that file data cannot be read.
Replace original card or select a new
application file from new card.
Mismatched application file.
The application file is for the wrong type of
terminal, for example, a keypad application
is being selected on a touch screen
terminal.
Note: If the JP2 jumper has been set
incorrectly, the application file will be
executed in Run mode.
Download an application file of the
appropriate type.
No memory card in the socket. Please replace
and try again.
There is no memory card in the socket.
Insert a compatible memory card in the
socket and try your action again.
No screen change—Hold Time in effect or no PLC
handshake.
You have requested a screen change while
the hold time for a momentary push button
is still in effect.
Wait for the momentary push button to
release before changing screens OR
shorten the hold time of the push button.
You have requested a screen change while
a latched push button is still waiting for
acknowledgement from the PLC.
Check that the latched button acknowledge
tag and PLC program have been
programmed correctly.
Partition is incorrectly formatted. Please reformat.
The PCMCIA memory card’s format is
incompatible with the terminal.
Reformat the PCMCIA memory card using
the Format PCMCIA Card button in the
Memory Card Transfer Application screen.
Partition full. Please reformat or use another
partition.
The partition on the extended system
memory or PCMCIA memory card is full.
Download or transfer your file to another
partition.
Reformat the partition using the Format
Destination button in the Memory Card
Transfer Application window.
PLC currently controls screen change.
You have requested a screen change while
the PLC has control.
To use manual screen changing, set the
PLC Controlled Screen Number value to 0 .
PLC currently controls scrolling list.
The scrolling list cannot be manually
scrolled while the PLC has control.
To use manual scrolling, set the Enable PLC
Controlled List value to 0 .
PLC did not acknowledge Enter Bit.
The PLC didn’t acknowledge the Enter
Control tag within the configured handshake
timeout.
Check that the enter key handshake timeout
and PLC program have been configured
correctly.
Publication 2711E-6.17 – November 1998
8–6
Troubleshooting PanelView Terminals
Mistake Message
Cause
What To Do
Requested screen is already displayed.
You have requested a change to a screen
that is currently displayed.
Check that the screen selector object is
configured for a different screen.
Screen does not exist—Retry.
You have requested a change to a screen
that doesn’t exist.
Check that the screen selector object is
configured for a valid screen.
Screen print ignored—a previous request is
already queued.
You have requested a screen print while
one is already printing.
Wait for the screen print to complete before
requesting another.
The acknowledge for this alarm is outside the
defined address.
The trigger value for the acknowledged
alarm is not within the valid range for the
configured PLC address.
Check that the alarm’s trigger value and
Acknowledge Alarm to PLC tag address
have been configured correctly.
Unknown memory card type. Please replace.
You are using a memory card type that is
not recognized by the terminal.
Replace with a compatible memory card.
See Appendix A in this manual for a list of
compatible memory cards.
Value out of range.
A screen object has attempted to write a
value to the PLC that is not within the valid
range for the configured PLC address.
Check that the object’s state values and
PLC address have been properly
configured.
Firmware Messages
The following table lists the messages that are displayed when the
firmware is booted into the wrong PanelView terminal.
Firmware Message
Cause
What To Do:
This Firmware requires a PV 1000e Terminal.
The firmware is booted into the wrong
PanelView terminal. It should be booted into
a PanelView 1000e terminal.
Check if the firmware is on a PCMCIA card
that has been upgraded for a particular
terminal type and then plugged into a
different terminal type.
This Firmware requires a PV 1200/1400e
Terminal.
The firmware is booted into the wrong
PanelView terminal. It should be booted into
a PanelView 1200/1400e terminal.
Check if the firmware is on a PCMCIA card
that has been upgraded for a particular
terminal type and then plugged into a
different terminal type.
This Firmware requires a touch terminal.
The firmware is booted into the wrong
PanelView terminal. It should be booted into
a PanelView touch screen terminal.
Check if the firmware is on a PCMCIA card
that has been upgraded for a particular
terminal type and then plugged into a
different terminal type.
This Firmware requires a keypanel terminal.
The firmware is booted into the wrong
PanelView terminal. It should be booted into
a PanelView keypad terminal.
Check if the firmware is on a PCMCIA card
that has been upgraded for a particular
terminal type and then plugged into a
different terminal type.
Publication 2711E-6.17 – November 1998
Troubleshooting PanelView Terminals
PLC Communication
Problems: Remote I/O
8–7
Consult the following table to identify PLC communication
problems over Remote I/O.
Problem
Cause
What To Do
“PLC Communication Lost” message on the
PanelView terminal.
Cable problem.
Check termination and cable pin
assignments.
Rack assignments in the terminal and PLC
do not match.
Make sure rack assignments in PLC match
those in the terminal.
Terminating resistor not installed properly.
Install the terminating resistor at both ends
of the link:
150 1/2 watt resistor for 57.6 or 115.2
kbaud
82 1/2 watt resistor for 230 kbaud
PanelView terminal and Remote I/O
Scanners baud rate do not match.
Change the Remote I/O baud rate in the
PanelView terminal or the scanner so they
match.
The terminal has been assigned to multiple
or partial racks when firmware revision of
PLC-5 does not support partial rack
addressing.
Configure the PanelView terminal as a
single full rack.
Upgrade PLC-5/15 to Series B Revision H
or later.
Upgrade PLC-5/25 to Series A Revision D
or later.
PLC is not configured to recognize the
terminal’s rack assignments.
Refer to your PLC-5 User’s Manual
regarding Auto Configuration.
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
“PLC Communication Lost” message when using
the PanelView terminal with PLC-5.
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
Partial PLC Comms Lost – Some racks (buttons
or indicators) may still be active.
The rack has been disabled.
Re-enable the rack by using the PLC
Programming Software.
Periodic “PLC Communication Lost” when using
1772-SD2 scanner with PLC-2s.
Use 1772-SD2 scanner Rev. 3 or later.
Rapid blinking of “PLC Communication Lost”
when using 1775-S4A scanner with a PLC-3.
Use 1775-S4A scanner Series B or later.
“PLC Communication Lost” when using SLC 500
1747-SN Scanner Module.
The 1747-SN Scanner Module is not
configured correctly.
Refer to 1747-RIO Scanner User’s Manual
regarding Specialty I/O Configuration and
how to configure Mfiles and Gfiles.
Verify that the PanelView terminal and the
1747-SN Scanner Module Remote I/O baud
rates are set the same.
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
Discrete I/O works but block transfer does not. No
“PLC Communication Lost” message. Using
PLC-5/15, partial rack addressing.
Use PLC-5/15 series B Rev. J or later.
Discrete I/O works but block transfer does not. No
“PLC Communication Lost” message.
Block transfer assignments in the terminal
do not match block transfer instructions in
PLC.
Make sure PLC block transfer instruction
parameters match the terminal parameters.
PLC Controller rack fault on rack assigned to the
PanelView 1200e terminal.
Specified No for Last Chassis when the
terminal is the last chassis in that rack.
Set Last chassis to Yes for that rack
assignment.
“PLC Communication Lost” message and rack
fault on rack assigned to the PanelView 1200e
terminal.
Mismatched baud rate on the terminal and
PLC.
Specify same baud rate for the terminal and
PLC.
Multiple devices configured for the same
rack assignment.
Ensure multiple remote I/O devices have
unique rack assignments.
Publication 2711E-6.17 – November 1998
8–8
Troubleshooting PanelView Terminals
Problem
Cause
What To Do
Remote I/O : PLC Communication Lost.
Cable disconnected or wired incorrectly.
Terminating resistor problem.
Check that the cable is securely connected
and cable wiring is correct. Check
terminating resistor.
PLC configured incorrectly.
Check PLC configuration and correct if
necessary.
The corresponding I/O Control Inhibit bit to
any PanelView defined I/O racks is set to 1.
Reset the corresponding I/O Control Inhibit
bit to zero.
Remote I/O : One or more Listen-Only
racks are faulted.
The racks that the terminal is monitoring are
faulted.
Check that the device containing the rack
being monitored has been properly
configured at the PLC.
Remote I/O: PLC in Program Mode or a
Configured Rack is Reset.
Corresponding I/O Control Reset bit to any
of the PanelView defined I/O racks is set to
1 and the PLC is in Run mode. The
PanelView continues to function normally
including the reset racks.
Reset the I/O Control bits to zero.
Ensure the PLC is in Program mode when
performing maintenance operations.
PLC is in Program or Remote Program
mode.
Change PLC to Run mode.
PLC Communication
Problems: Data Highway
Plus
Consult the following table to identify PLC communication
problems over the DH+ network. At run time, the ## appears at the
terminal as the station address of the node to which the error applies.
Problem
Cause
What To Do
DH+## : Access denied to remote station,
improper privilege.
The indicated station is a PLC that is
loading a program over the network. Or, on
an SLC 5/04, the memory map tables may
have protection (static or constant).
Wait for the transfer to complete or remove
protection.
DH+## : Remote station does not match the
configured PLC.
The device type of the remote station does
not match that configured in PanelBuilder.
Check that the node definitions in your
application file are configured with the
correct device type.
DH+## : Remote station has not replied within
specified timeout period.
Network traffic is too heavy for configured
timeout.
Increase the configured timeout for the
indicated station.
Cable problem.
Check for a loose connection or damaged
cable at the indicated station.
DH+## : Remote station is in Program mode.
PLC is in Program or Remote Program
mode.
Change PLC to Run mode.
DH+## : Station address is already in use by
another device.
The PanelView terminal cannot
communicate with the indicated station
because the terminal has been configured
with a station address that is already in use
on the DH+ network.
Select another station address.
DH+## : Tag address is not valid for this PLC.
The terminal is trying to access a tag whose
address does not exist at the indicated PLC.
Check that the tag addresses in your PLC
are correct and the PLC has been correctly
configured.
DH+## : Unable to communicate with remote
station.
The indicated remote station does not exist
on the DH+ network.
Check that the remote station is present and
active at the indicated station address.
Cable problem.
Check termination and cable pin
assignment.
Publication 2711E-6.17 – November 1998
Troubleshooting PanelView Terminals
PLC Communication
Problems: ControlNet
8–9
Consult the following table to identify PLC communication
problems over the ControlNet network. At run time, the ## appears
at the terminal as the decimal station address of the node to which
the error applies.
Problem
Cause
What To Do
CNet## : Access denied to remote station,
improper privilege.
The indicated station is a PLC that is
loading a program over the network.
Wait for the transfer to complete.
The indicated station is a PLC that is
FAULTED.
Check PLC configuration and correct if
necessary.
CNet## : Remote station does not match the
configured PLC.
The device type of the remote station does
not match that configured in PanelBuilder.
Check that the node definitions in your
application file are configured with the
correct device type.
CNet## : Remote station has not replied within
specified timeout period.
Network traffic is too heavy for configured
timeout.
Increase the configured timeout for the
indicated station.
Cable problem.
Check for a loose connection or damaged
cable at the indicated station.
CNet## : Remote station is in Program mode.
PLC is in Program or Remote Program
mode.
Change PLC to Run mode.
CNet## : Station address is already in use by
another device.
The PanelView terminal cannot
communicate with the indicated station
because the terminal has been configured
with a station address that is already in use
on the ControlNet network.
Select another station address.
CNet## : Tag address is not valid for this PLC.
The terminal is trying to access a tag whose
address does not exist at the indicated PLC.
Check that the tag addresses in your PLC
are correct and the PLC has been correctly
configured.
CNet## : Unable to communicate with remote
station.
The indicated remote station does not exist
on the ControlNet network.
Check that the remote station is present and
active at the indicated station address.
The PanelView terminal cannot
communicate with the indicated station
because the terminal has been configured
with a station address that is already in use
on the ControlNet network.
Select another station address.
Cable problem.
Check for a loose connection or damaged
cable at the indicated station.
The ControlNet Unscheduled application
does not support unsolicited messaging.
Modify the message command from the
PLC logic that communicates with the
PanelView terminal.
CNet## : Transaction size plus word address too
large.
Publication 2711E-6.17 – November 1998
Specifications: 1000e
Operator Terminal
Product List
Specifications in this appendix apply to the following products
unless otherwise indicated:
• 2711E-T10C6 (touch screen)
• 2711E-K10C6 (keypad)
• 2711E-T10C7 (touch screen for ControlNet 1.25)
• 2711E-K10C7 (keypad for ControlNet 1.25)
• 2711E-T10C15 (touch screen for ControlNet 1.5)
• 2711E-K10C15 (keypad for ControlNet 1.5)
Approvals and
Compliances
The PanelView 1000e terminal meets the following safety, EMC, and
environmental standards.
Safety Standards Approvals
• UL 508
• CUL (CSA equivalent) 22.2 no. 142 listed through UL program
• EU Low Voltage Directive Compliance—see next page
EMC Standards Compliance
• EU EMC Directive Compliance—see next page
• ICES 003 (Industry Canada) Class A
• FCC Part 15, subpart B, Class A
Environmental Standards
PanelView 1000e terminals meet the following standards when
mounted in like enclosures:
• CSA C22–2 No. 94–M91, ENCL 4X, 12 (Indoor Use Only) from
the front
• UL 50, 1992, ENCL 4X, 12 (Indoor Use Only) from the front
• NEMA 4X, 12 (Indoor Use Only) from the front
• IEC 529, IP66 (Indoor Use Only)
Publication 2711E-6.17 – November 1998
A–2
Specifications: 1000e Operator Terminal
European Union Directive
Compliance
If the PanelView 1000e Operator Terminals are installed within the
European Union or EFTA regions and have a CE mark, the following
regulations apply.
EMC Directive
This product is tested to meet Council Directive 89/336/EEC
Electromagnetic Compatibility (EMC), using the following standards
in whole or in part.
• EN 50081-2:1993 (EMC Generic Emission Standard
Part 2–Industrial Environment)
• EN 50082-2:1995 (EMC Generic Immunity Standard
Part 2–Industrial Environment)
Low Voltage Directive
This product is tested to meet Council Directive 73/23/EEC with
amendments, including 93/68/EEC Low Voltage (LVD), using the
pertinent sections of the following standards.
• EN61010-1:1995 (Safety Requirements for Electrical Equipment
for Measurement, Control, and Laboratory Use)
Intended Use of Product
According to these Standards, the factor that determines, for EMC
purposes, whether an apparatus is deemed to be “industrial” or
“Residential, commercial and light industrial,” is given in Clause 1
of EN50081-2 as follows:
Apparatus covered by this standard is not intended for connection to
a public mains network. It is intended for connection to an
Installation Category II, a power network supplied from a high- or
medium-voltage transformer dedicated for the supply of an
installation feeding a manufacturing or similar plant.
PanelView 1000e Operator terminals are intended for use solely in
an industrial environment as defined above. When installed in
Europe, any other application is in contravention of European Union
Directives, and a breach of these laws.
Publication 2711E-6.17 – November 1998
Specifications: 1000e Operator Terminal
Wiring Recommendations
A–3
Careful wire routing helps cut down on electrical noise. To reduce
electrical noise, the PanelView 1000e Operator Terminal should be
connected to its own branch circuit.
!
ATTENTION: The input power source should be
protected by a fuse or circuit breaker rated at no more
than 15 amps.
Route incoming power to the PanelView 1000e terminal by a
separate path from the communication cable.
!
ATTENTION: Do not run signal wiring and power
wiring in the same conduit.
Where power and communication lines must cross, they should do so
at right angles. Communication lines can be installed in the same
conduit as low-level, dc I/O lines (less than 10 volts).
Terminal Weights
• Keypad terminal
• Touch screen terminal
11.6 lbs (5.3 kg)
11.3 lbs (5.1 kg)
These weights do not include any shipping materials used to package
the terminal.
Front Panel Design
This section describes front panel design specifications for the
PanelView 1000e keypad and touch screen terminals.
Keypad Terminals
Key Panel:
sealed, stainless steel dome membrane switches with
tactile feedback and an actuation force of 1 lb.
(0.455 kg), mounted on the key panel’s reinforced
plastic bezel, protected with a hard-coated,
scratch-resistant polyester surface. Keys are rated for
2,000,000 presses.
Window:
clear, hard-coated, scratch-resistant polyester
over chemically strengthened glass
Custom legends can be inserted in the 21 user-configurable function
keys.
Publication 2711E-6.17 – November 1998
A–4
Specifications: 1000e Operator Terminal
Touch Screen Terminals
Membrane:
clear, hard-coated, scratch-resistant
polyester, over chemically
strengthened glass
Bezel:
reinforced plastic
Touch cell actuation force: from 2.5 to 3.5 oz (71 to 100 grams)
Touch Cell Format
• User can configure to any size touch cell
• Minimum 40 × 40 pixel touch cell
• Maximum number of touch cells is 192 (16 × 12)
Touch cells are rated for 1,000,000 presses.
Flat Panel Display
The following table provides display specifications.
Display Format
640 horizontal by 480 vertical pixels
Display Intensity
Low to high range adjustment using the firmware to
control the intensity level.
Screen Saver Timeout
User-configurable, 0 – 60 minute timeout.
0 disables the screen saver.
Screen Saver Display Intensity
Low to high range adjustment using the firmware to
control the intensity level. The screen saver can be
switched off.
Display Size
10.4-inch diagonal TFT Active Matrix Display,
211.2 mm 158.4 mm image size
Backlight Life
The PanelView 1000e terminal has a replaceable backlight. The
backlight has an expected minimum life of 10000 hours at maximum
brightness. This life can be significantly extended by reducing the
brightness level and using the screen saver.
Publication 2711E-6.17 – November 1998
Specifications: 1000e Operator Terminal
A–5
Color Unit Display Attributes
There are 256 fixed colors for screen objects.
Attributes, which are controlled and defined through the software,
include blink and underline. Character sizes include 1 × 1
(8 × 20 pixels—standard), 1 × 2 (8 × 40 pixels—double height),
2 × 1 (16 × 20 pixels—double width), 2 × 2 (16 × 40—double
height, double width), and 2 × 4 (16 × 80—extra large).
Data Highway Plus
Communications
•
•
•
•
•
ControlNet
Communications
•
•
•
•
PLC Remote I/O
Communications
The parameters of the PLC Remote I/O Communications are:
• Allen-Bradley PLC via Allen-Bradley 1771 Remote I/O Link
• Remote I/O baud rate: 57.6/115.2/230.4 kilobaud
• Maximum I/O cable distance: 10,000 ft. (57.6 kilobaud)
5,000 ft. (115.2 kilobaud)
2,500 ft. (230.4 kilobaud)
• 5000 tags maximum
• Terminal can emulate: from 1/4 to 64 full Remote I/O Racks
• Rack sizes:1/4, 1/2, 3/4, or full (any starting module group). A
rack can be configured for full or listen-only access.
• Total discrete I/O possible: 64 racks × 8 words/rack × 16
bits/word input and output bits, or 64 × 8 PLC input and 64 × 8
PLC output words
Allen-Bradley Data Highway Plus
Baud rate may be 57.6, 115.2, or 230.4 kilobaud
5000 tags maximum
Communicates with local and bridged stations on DH+
Unsolicited messages to and from the PLC using PLC2
unprotected message formats. 512 words of address space.
• File transfer over DH+ network including over bridged DH+
Allen-Bradley ControlNet
Baud rate is 5 Mbits/s
5000 tags maximum
Communicates with local stations on ControlNet using scheduled
and unscheduled modes
• Unsolicited messages to and from the PLC using PLC2
unprotected message formats. 512 words of address space.
• File transfer over ControlNet network
Publication 2711E-6.17 – November 1998
A–6
Specifications: 1000e Operator Terminal
• Up to 64 block transfer files can be configured, with up to 64
words for each file. Files can be configured as read or write files
in any combination.
• Total Block Transfer bits possible: 64 files × 64 word/file ×
16 bit/word in any input/output combination
• Application files can be uploaded and downloaded by the PLC-5
or SLC 5/04 Pass-Through feature
Serial Communications
Port
The RS-232 serial communications port can be connected to either
the development system for uploading/downloading application files,
or to a printer for printing screen images, alarm history and alarm
status reports, or alarm messages. Separate port settings can be
assigned for each of these purposes. The applicable printer port
settings are used automatically and are as follows, with the default in
brackets:
Baud Rates
300,1200, 2400, 4800, 9600, 19.2 kilobaud (9600)
Parity Types
Odd, Even, None (None)
Stop Bits
1, 2 (1)
Data Bits
7, 8 (8)
Handshake
Hardware, Software (X-ON, X-OFF), None (Software)
Auto Line Feed
Off, On (On)
Auto Form Feed
Off, On (On)
The factory defaults for file transfer are the same as the default
settings the development software will apply to the selected RS-232
port on your development system, so you don’t normally need to
change them.
File transfer settings are separate from the printer and are as follows:
Publication 2711E-6.17 – November 1998
Baud Rates
300,1200, 2400, 9600, 19200 (9600)
Parity Types
Even, None (None)
Error
CRC, BCC (BCC)
Specifications: 1000e Operator Terminal
Keyboard and Bar Code
Reader Support
A–7
Following are the keyboards supported by the PanelView 1000e
terminal.
Manufacturer
Part Number
Allen-Bradley
6189-KBM1
Allen-Bradley
6189-KBD1
Allen-Bradley
6189-KBE1
Following is the bar code reader supported by the PanelView 1000e
terminal.
PCMCIA Memory Card
Support
AC Power
Manufacturer
Part Number
Allen-Bradley
2755HDG4 Series A, Revision C
Following are the PCMCIA memory cards supported by the
PanelView 1000e terminal in 200-ns or faster configuration.
Manufacturer
Part Number
Memory Capacity
Allen-Bradley
2711-NM11
256 K
Allen-Bradley
2711-NM12
1 MB
Allen-Bradley
2711-NM13
2 MB
Allen-Bradley
2711-NM14
4 MB
Allen-Bradley
2711-NM15
8 MB
Following are the ac power specifications for the PanelView 1000e
terminal.
Power Supply Type
Switching
Range
90–132, 180–264 V ac
automatic setting by the PanelView 1000e terminal to
match available power supply
Frequency Range
47–63 Hz
Power Consumption
45 W typical
70 W maximum
Volt Amps
60 VA typical
90 VA maximum
Publication 2711E-6.17 – November 1998
A–8
Specifications: 1000e Operator Terminal
Fuses
PanelView 1000e terminals:
• require one fuse for each ac line
• has fuses the user can not access
• uses Littelfuse 218001, or equivalent, Type T, 1.0 A, 250 Vac,
5 mm × 20 mm
!
ATTENTION: Fuses must be replaced by authorized
service personnel only. PanelView 1000e terminals
contain neutral fuses. Disconnect power before
servicing the unit.
Character Set
PanelView 1000e terminals support the IBM character set for alarm,
local, and information messages.
User Memory
PanelView 1000e terminals support:
• 2.25 MB of Flash memory for application file
• PCMCIA card of variable size (depends on user application file),
256K to 16 MB
RAM tests and Memory Checksum tests can be initiated in the
Terminal Diagnostics screen in Configuration mode.
Alarm Relay
•
•
•
•
•
Batteries
PanelView’s permanent, factory-installed lithium battery has a total
lithium weight of not more than 0.5 gram. The battery is not
burdened when ac power is applied to the terminal. The following
chart indicates battery life, with continuous exposure to the specified
temperatures, assuming ac power is applied to the terminal 8 hours a
day, 5 days a week. These calculations are based on battery life
specifications provided by the battery manufacturer and do not take
battery shelf life into account.
Form-C Contact
24 V ac Max, 1 amp continuous Max
24 V dc Max, 1 amp continuous Max
Minimum Voltage: 100 mV dc
Minimum Current: 10 mA dc
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
+86° F (+30° C)
7.7 years
+104° F (+40° C)
4.5 years
+113° F (+45° C)
3.8 years
+122° F (+50° C)
3.2 years
+140° F (+60° C)
2.5 years
Battery fail indications are displayed automatically.
Publication 2711E-6.17 – November 1998
Specifications: 1000e Operator Terminal
Time and Date Clock
A–9
• Display modes: AM/PM or 24-hour (hours, minutes, seconds);
•
•
•
•
•
optional show seconds, leading digit is zero or blank
Date display includes month, day, and year: order (MDY, DMY,
YMD), 2/4 digit year format (except fixed 2-digit for Alarm
History screen), leading digit is zero or blank
Time and date plus “day of week” can be transferred to the host
PLC
Time and date can be transferred from the host PLC to the
terminal to synchronize the terminal’s date and time
Battery-backed
Automatic leap year correction
The clock’s accuracy can vary by ±7 minutes per month over an
operating temperature range of 0° C to 60° C.
Temperature, Humidity,
and Altitude
The following are temperature, humidity, and altitude requirements
for the PanelView 1000e terminal.
Ambient Operating Temperature Limits
• Maximum: +50° C (+122° F)
• Minimum: 0° C (+32° F)
Storage Temperature Limits
• Minimum: -25° C (-13° F)
• Maximum: +60° C (+140° F)
Humidity
• +50° C at 95% humidity (non-condensing)
Maximum Altitude
• Non-operating or storage: 40,000 feet
• Operating: 6500 feet
Heat Generation
154 BTU/hour typical
290 BTU/hour maximum
Publication 2711E-6.17 – November 1998
A–10
Specifications: 1000e Operator Terminal
Shock and Vibration
The following are shock and vibration specifications for the
PanelView 1000e terminal.
Shock Amplitudes
• Operating 15 G (peak acceleration)
• Non-operating 30 G (peak acceleration)
Vibration Amplitudes for Operating Units
Frequency range: 5 to 150 Hz
• 5 to 57 Hz: 0.012–inch peak-to-peak displacement
• 58 to 150 Hz: 2.0 G peak acceleration
Publication 2711E-6.17 – November 1998
Specifications: 1200e
Operator Terminal
Product List
Specifications in this appendix apply to the following products
unless otherwise indicated:
• 2711E-T12C6 (color touch screen; clip-mount)
• 2711E-T12C4 (color touch screen; stud-mount)
• 2711E-K12C6 (keypad)
• 2711E-K12C6L2 (stainless steel keypad)
Approvals and
Compliances
The PanelView 1200e terminal meets the following safety, EMC, and
environmental standards.
Safety Standards Approvals
• UL 508
• CUL (CSA equivalent) 22.2 no. 142 listed through UL program
EMC Standards Compliance
• ICES 003, Class A
• FCC Part 15, subpart B, Class A
• VDE-0871 Class A
Environmental Standards
PanelView 1200e terminals meet the following standards when
mounted in like enclosures:
Keypad Terminals
• CSA C22–2 No. 94–M91, ENCL 4X, 12, 13 (Indoor Use Only)
from the front
• UL 50, 1992, ENCL 4X, 12. 13 (Indoor Use Only) from the front
• NEMA 4X, 12, 13 (Indoor Use Only) from the front
Touch Screen Terminals
Stud mount:
• CSA C22–2 No. 94–M91, ENCL 4X, 12, 13 (Indoor Use Only)
from the front
• UL 50, 1992, ENCL 4X, 12, 13 (Indoor Use Only) from the front
• NEMA 4X, 12, 13 (Indoor Use Only) from the front
Publication 2711E-6.17 – November 1998
B–2
Specifications: 1200e Operator Terminal
Clip-mount:
• CSA C22–2 No. 94–M91, ENCL 12, 13 (Indoor Use Only) from
the front
• UL 50, 1992, ENCL 12, 13 (Indoor Use Only) from the front
• NEMA 12, 13 (Indoor Use Only) from the front
•
•
Terminal Weights
Keypad terminal
33.8 lbs (15.3 kg)
Touch screen terminal 32.6 lbs (14.8 kg)
These weights do not include any shipping materials used to package
PanelView 1200e terminals.
Front Panel Design
This section describes front panel design specifications for the
PanelView 1200e keypad and touch screen terminals.
Keypad Terminals
Key Panel:
black anodized sheet aluminum with continuous
hard-coated, scratch-resistant polyester surface
Keys:
sealed, stainless steel dome membrane switches with
tactile feedback and an actuation force of 1 lb
(0.455 kg), mounted on the key panel’s anodized
aluminum backer plate. Keys are rated for
2,000,000 presses.
Window:
continuous water-clear polyester over chemically
strengthened glass
Custom legends can be inserted in the 21 user-configurable function
keys and the Select, Cancel, Raise and Lower keys.
Stainless Steel Keypad Terminals
Stainless Steel: 304, brushed, #4 finish
"
Publication 2711E-6.17 – November 1998
Note: There are no custom legend inserts on Stainless Steel Keypad
Terminals.
Specifications: 1200e Operator Terminal
B–3
Touch Screen Terminals
Membrane:
water-clear, hardcoated,
scratch-resistant polyester,
over chemically strengthened glass
Bezel:
cast aluminum with black powder
coating
Touch cell actuation force:
from 2.5 to 3 oz (71 to 85 grams)
Touch Cell Format
• Matrix of 120 touch cells (10 across by 12 high)
• Each touch cell is 40 pixels high by 64 pixels wide
• User can configure or group cells to any size buttons
Touch cells are rated for 1,000,000 presses.
CRT Display
The following tables provide details of the display specifications.
Display Format
640 horizontal by 480 vertical pixels
Display Alignment
User-configurable, stored in non-volatile memory
Color: 5 pixels horizontal range, 9 pixels vertical range
Display Intensity
Low to high range adjustment on back of unit
Screen Saver
User-configurable, 0 – 60 minute timeout. 0 disables the
screen saver.
Display Size
12-inch diagonal. 204 mm × 137 mm
Color Unit Display Attributes
There are 16 fixed colors for screen objects:
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
Black
Grey
Light Grey
White
Red
Bright Red
Blue
Bright Blue
Green
Bright Green
Magenta
Bright Magenta
Cyan
Bright Cyan
Yellow
Bright Yellow
Publication 2711E-6.17 – November 1998
B–4
Specifications: 1200e Operator Terminal
Other attributes include blink and underline. Character sizes include
1 × 1 (8 × 20 pixels—standard), 1 × 2 (8 × 40 pixels—double
height), 2 × 1 (16 × 20 pixels—double width), 2 × 2 (16 ×
40—double height, double width) and 2 × 3 (16 × 80—extra large).
Degauss
Automatic degauss occurs each time ac power is re-applied to the
unit and at midnight (according to the terminal system clock) daily.
Data Highway Plus
Communications
•
•
•
•
•
PLC Remote I/O
Communications
The parameters of the PLC Remote I/O Communications are:
• Allen-Bradley PLC via Allen-Bradley 1771 Remote I/O Link
• Remote I/O baud rate: 57.6/115.2/230.4 kilobaud
• Maximum I/O cable distance: 10,000 ft. (57.6 kilobaud)
5,000 ft. (115.2 kilobaud)
2,500 ft. (230.4 kilobaud)
• 5000 tags maximum
• Terminal can emulate from 1/4 to 64 full Remote I/O Racks
• Rack sizes: 1/4, 1/2, 3/4, or full (any starting module group). A
rack can be configured for full or listen-only access.
• Total discrete I/O possible: 64 racks × 8 words/rack ×
16 bits/word input and output bits, or 64 × 8 PLC input and
64 × 8 PLC output words
• Up to 64 block transfer files can be configured, with up to 64
words for each file. Files can be configured as read or write files
in any combination.
• Total Block Transfer bits possible64 files × 64 word/file ×
16 bit/word in any input/output combination
• Application files can be uploaded and downloaded by the PLC-5
and SLC5/04 Pass-Through feature
Publication 2711E-6.17 – November 1998
Allen-Bradley Data Highway Plus
Baud rate may be 57.6, 115.2, or 230.4 kilobaud
5000 tags maximum
Communicates with local and bridged stations on DH+
Unsolicited messages to and from the PLC using PLC2
unprotected message formats. 512 words of address space.
• File transfer over DH+ network including over bridged DH+
Specifications: 1200e Operator Terminal
Serial Communications
Port
B–5
The RS-232 serial communications port can be connected to either
the development system, for uploading/downloading application
files, or to a printer for printing screen images, alarm history and
alarm status reports, or alarm messages. Separate port settings can be
assigned for each of these purposes. The applicable printer port
settings are used automatically and are as follows, with the default in
brackets:
Baud Rates
300,1200, 2400, 4800, 9600, 19.2 kilobaud (9600)
Parity Types
Odd, Even, None (None)
Stop Bits
1, 2 (1)
Data Bits
7, 8 (8)
Handshake
Hardware, Software (X-ON, X-OFF), None (Software)
Auto Line Feed
Off, On (On)
Auto Form Feed
Off, On (On)
The factory defaults for file transfer are the same as the default
settings the development software will apply to the selected RS-232
port on your development system, so you don’t normally need to
change them.
The settings for file transfer are separate from the printer and are as
follows:
PCMCIA Memory Card
Support
Baud Rates
300,1200, 2400, 9600, 19200 (9600)
Parity Types
Even, None (None)
Error
CRC, BCC (BCC)
Following are the PCMCIA memory cards supported by the
PanelView 1200e Series A terminal in 200-ns or faster configuration.
Manufacturer
Part Number
Memory Capacity
Allen-Bradley
2711-NM11
256K
Allen-Bradley
2711-NM12
1 MB
Allen-Bradley
2711-NM13
2 MB
Allen-Bradley
2711-NM14
4 MB
Allen-Bradley
2711-NM15
8 MB
Publication 2711E-6.17 – November 1998
B–6
Specifications: 1200e Operator Terminal
AC Power
The following table provides details of the ac power specifications:
Power Supply Type
Switching
Range
90 – 132, 180 – 264 Vac
automatic setting by the PanelView 1200e terminal to
match available power supply
Frequency Range
47 – 63 Hz
Power Consumption
Color terminal
65 W typical
90 W maximum
Volt Amps
Color terminal
160 VA typical
220 VA maximum
While the color terminal degausses, there is a 5.5-amp surge at
115 volts. At 230 volts, there is an 11-amp surge. The surge lasts less
than 400 milliseconds. Automatic degauss occurs each time ac power
is re-applied to the unit and at midnight (according to the terminal
system clock) daily.
Fuses
PanelView 1200e terminals:
• Require one fuse for each ac line
• Have fuses that the user can access from the rear of the terminal
• Accept either US or European fuse types
– US fuse: BUSS AGC-3, 3 amps, 250 Vac, 1/4–inch ×
1-1/4–inch
– European fuse: BUSS GDB-3, 3 amps, 250 Vac, 5 mm ×
20 mm
!
ATTENTION: Fuses must be replaced by authorized
service personnel only. PanelView 1200e terminals
contain neutral fuses. Disconnect power before
servicing the unit.
Character Set
PanelView 1200e terminals support the IBM character set for alarm,
local, and information messages.
User Memory
The PanelView 1200e terminal supports:
• 256K of flash memory for application file
• PCMCIA card slot of variable size (256K bytes to 16 MB—depends
on user application file)
RAM tests and Memory Checksum tests can be initiated from the
Terminal Diagnostics screen in Configuration mode.
Publication 2711E-6.17 – November 1998
Specifications: 1200e Operator Terminal
B–7
Alarm Relay
•
•
•
•
•
Batteries
PanelView’s permanent, factory-installed lithium batteries have a
total lithium weight of not more than 1.0 gram. Batteries are not
burdened when ac power is applied to the terminal. The following
chart indicates battery life, with continuous exposure to the specified
temperatures, assuming ac power is applied to the terminal 8 hours a
day, 5 days a week. These calculations are based on battery life
specifications provided by the battery manufacturer and do not take
battery shelf life into account.
Form-C Contact
250 V ac max., 8 A continuous
30 V dc max., 8 A continuous
Minimum Voltage: 1 V dc
Minimum Current: 1 mA dc
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
+86° F (+30° C)
Greater than 10 years
+104° F (+40° C)
Greater than 10 years
+113° F (+45° C)
Greater than 10 years
+122° F (50° C)
10 years
+140° F (60° C)
7.5 years
Battery fail indications are displayed automatically.
Time and Date Clock
• Display modes: AM/PM or 24-hour (hours, minutes, seconds);
•
•
•
•
•
optional show seconds, leading digit is zero or blank
Date display includes month, day, and year: order (MDY, DMY,
YMD), 2/4 digit year format (except fixed 2-digit for Alarm
History screen), leading digit is zero or blank
Time and date plus “day of week” can be transferred to the host
PLC
Time and date can be transferred from the host PLC to the
terminal to synchronize the terminal’s date and time
Battery-backed
Automatic leap year correction
The clock’s accuracy can vary by ±7.0 minutes per month over an
operating temperature range of 0° C to 60° C.
Publication 2711E-6.17 – November 1998
B–8
Specifications: 1200e Operator Terminal
Temperature, Humidity,
and Altitude
The following are temperature, humidity, and altitude requirements
for the PanelView 1200e terminal.
Ambient Operating Temperature Limits
• Maximum: +50° C (+122° F)
• Minimum : 0° C (+32° F)
Storage Temperature Limits
• Maximum: +85° C (+185° F)
• Minimum: -40° C (-40° F)
Humidity
• Relative operating humidity (non-condensing)
– 0° to +30° C (+32°to +86° F) 95% humidity
– +30° to +40° C (+86° to +104° F) 75% humidity
– +40° to +50° C (+104° to +122° F) 40% humidity
• Relative non-operating humidity (non-condensing)
– -40° to +70° C (-40° to +158° F) 95% humidity
Maximum Altitude
• Non-operating or storage: 40,000 feet
• Operating: 10,000 feet
Heat Generation
The following are heat generation requirements for the PanelView
1200e color terminals.
Color Terminals
307 BTU/hour maximum
222 BTU/hour typical
Publication 2711E-6.17 – November 1998
Specifications: 1200e Operator Terminal
Shock and Vibration
B–9
The following are shock and vibration specifications for the
PanelView 1200e terminal.
Shock Amplitudes
• Operating 15 G (Peak Acceleration)
• Non-operating 30 G (Peak Acceleration)
Vibration Amplitudes for Operating Units
Frequency range: 5 to 2000 Hz
• 5 to 57 Hz: .006–inch peak-to-peak displacement
• 58 to 2000 Hz: 1.0 G peak acceleration
Vibration Amplitudes for Non-Operating Units
Frequency range: 5 to 2000 Hz
• 5 to 57 Hz: .015–inch peak-to-peak displacement
• 58 to 2000 Hz: 2.5 G peak acceleration
Publication 2711E-6.17 – November 1998
Specifications: 1400e
Operator Terminal
Product List
Specifications in this appendix apply to the following products
unless otherwise indicated:
• 2711E-T14C6 (touch screen)
• 2711E-K14C6 (keypad)
• 2711E-T14C7 (touch screen for ControlNet 1.25)
• 2711E-K14C7 (keypad for ControlNet 1.25)
• 2711E-T14C15 (touch screen for ControlNet 1.5)
• 2711E-K14C15 (keypad for ControlNet 1.5)
Approvals and
Compliances
The PanelView 1400e terminal meets the following safety, EMC, and
environmental standards.
Safety Standards Approvals
• UL 508
• CUL (CSA equivalent) 22.2 no. 142 listed through UL program
• EU Low Voltage Directive Compliance—see next page
EMC Standards Compliance
• EU EMC Directive Compliance—see next page
• FCC Part 15, subpart B, Class A
• ICES 003, Class A
Environmental Standards
PanelView 1400e terminals meet the following standards when stud
mounted in like enclosures:
• CSA C22–2 No. 94–M91, ENCL 4X, 12, 13 (Indoor Use Only)
from the front
• UL 50, 1992, ENCL 4X, 12, 13 (Indoor Use Only) from the front
• NEMA 4X, 12, 13 (Indoor Use Only) from the front
• IEC 529, IP65 (Indoor Use Only)
Publication 2711E-6.17 – November 1998
C–2
Specifications: 1400e Operator Terminal
European Union Directive
Compliance
If the PanelView 1400e Operator Terminals are installed within the
European Union or EFTA regions, the following regulations apply.
EMC Directive
This product is tested to meet Council Directive 89/336/EEC
Electromagnetic Compatibility (EMC), using the following standards
in whole or in part.
• EN 50081-2:1993 (EMC Generic Emission Standard
Part 2–Industrial Environment)
• EN 50082-2:1995 (EMC Generic Immunity Standard
Part 2–Industrial Environment)
Low Voltage Directive
This product is tested to meet Council Directive 73/23/EEC with
amendments, including 93/68/EEC Low Voltage (LVD), using the
pertinent sections of the following standards.
• EN61010-1:1995 (Safety Requirements for Electrical Equipment
for Measurement, Control, and Laboratory Use)
Intended Use of Product
According to these Standards, the factor that determines, for EMC
purposes, whether an apparatus is deemed to be “industrial” or
“Residential, commercial and light industrial,” is given in Clause 1
of EN50081-2 as follows:
Apparatus covered by this standard is not intended for connection to
a public mains network. It is intended for connection to an
Installation Category II, a power network supplied from a high- or
medium-voltage transformer dedicated for the supply of an
installation feeding a manufacturing or similar plant.
PanelView 1400e Operator terminals are intended for use solely in
an industrial environment as defined above. When installed in
Europe, any other application is in contravention of European Union
Directives, and a breach of these laws.
Publication 2711E-6.17 – November 1998
Specifications: 1400e Operator Terminal
Wiring Recommendations
C–3
Careful wire routing helps cut down on electrical noise. To reduce
electrical noise, connect the PanelView 1400e Operator Terminal to
its own branch circuit. The input power source should be protected
by a fuse or circuit breaker rated at no more than 15 amps. Route
incoming power to the PanelView 1400e terminal by a separate path
from the communication cable.
!
ATTENTION: Do not run signal wiring and power
wiring in the same conduit.
Where power and communication lines must cross, they should do so
at right angles. Communication lines can be installed in the same
conduit as low-level, dc I/O lines (less than 10 volts).
Terminal Weights
• Keypad terminal
• Touch screen terminal
44.6 lbs (20.2 kg)
43.5 lbs (19.7 kg)
These weights do not include any shipping materials used to package
the terminal.
Front Panel Design
This section describes front panel design specifications for the
PanelView 1400e keypad and touch screen terminals.
Keypad Terminals
Key Panel:
black powder-coated, cast aluminum with
hard-coated, scratch-resistant polyester surface
Keys:
sealed, stainless steel dome membrane switches with
tactile feedback and an actuation force of 1 lb.
(0.455 kg), mounted on the key panel’s anodized
aluminum backer plate. Keys are rated for
2,000,000 presses.
Window:
95% gloss, hard-coated, scratch-resistant polyester
over chemically strengthened glass
Custom legends can be inserted in the 21 user-configurable function
keys and the Select, Cancel, Raise and Lower keys.
Publication 2711E-6.17 – November 1998
C–4
Specifications: 1400e Operator Terminal
Touch Screen Terminals
Membrane:
95% gloss, hard-coated,
scratch-resistant polyester, over
chemically strengthened glass
Bezel:
cast aluminum with black powder
coating
Touch cell actuation force: from 2.5 to 3 oz (71 to 85 grams)
Touch Cell Format
• User can configure to any size touch cell
• Minimum 40 × 40 pixel touch cell
• Maximum number of touch cells is 192 (16x12)
Touch cells are rated for 1,000,000 presses.
CRT Display
The following table provides display specifications.
Display Format
640 horizontal by 480 vertical pixels
800 horizontal by 600 vertical pixels
Display Alignment
Can be adjusted by the user using HPOS and
VPOS controls.
Display Intensity
Low to high range adjustment using contrast and
brightness controls.
Screen Saver
User-configurable, 0–60 minute timeout. 0 disables
the screen saver.
Display Size
14-inch diagonal CRT, 247.6 mm × 185.7 mm
image size
Color Unit Display Attributes
There are 256 fixed colors for screen objects.
Attributes, which are controlled and defined through the software,
include blink and underline. Character sizes include 1 × 1
(8 × 20 pixels—standard), 1 × 2 (8 × 40 pixels—double height),
2 × 1 (16 × 20 pixels—double width), 2 × 2 (16 × 40—double
height, double width), and 2 × 3 (16 × 80—extra large).
Degauss
Automatic degauss occurs each time ac power is re-applied to the
unit.
Publication 2711E-6.17 – November 1998
Specifications: 1400e Operator Terminal
C–5
Data Highway Plus
Communications
•
•
•
•
•
ControlNet
Communications
•
•
•
•
PLC Remote I/O
Communications
The parameters of the PLC Remote I/O Communications are:
• Allen-Bradley PLC via Allen-Bradley 1771 Remote I/O Link
• Remote I/O baud rate: 57.6/115.2/230.4 kilobaud
• Maximum I/O cable distance: 10,000 ft. (57.6 kilobaud)
5,000 ft. (115.2 kilobaud)
2,500 ft. (230.4 kilobaud)
• 5000 tags maximum
• Terminal can emulate: from 1/4 to 64 full Remote I/O Racks
• Rack sizes: 1/4, 1/2, 3/4, or full (any starting module group). A
rack can be configured for full or listen-only access.
• Total discrete I/O possible: 64 racks × 8 words/rack ×
16 bits/word input and output bits, or 64 × 8 PLC input and
64 × 8 PLC output words
• Up to 64 block transfer files can be configured, with up to
64 words for each file. Files can be configured as read or write
files in any combination.
• Total Block Transfer bits possible: 64 files × 64 word/file ×
16 bit/word in any input/output combination
• Application files can be uploaded and downloaded by the PLC-5
or SLC 5/04 Pass-Through feature
Allen-Bradley Data Highway Plus
Baud rate may be 57.6, 115.2, or 230.4 kilobaud
5000 tags maximum
Communicates with local and bridged stations on DH+
Unsolicited messages to and from the PLC using PLC2
unprotected message formats. 512 words of address space.
• File transfer over DH+ network including over bridged DH+
Allen-Bradley ControlNet
Baud rate is 5 Mbits/s
5000 tags maximum
Communicates with local stations on ControlNet using scheduled
and unscheduled modes
• Unsolicited messages to and from the PLC using PLC2
unprotected message formats. 512 words of address space.
• File transfer over ControlNet network
Publication 2711E-6.17 – November 1998
C–6
Specifications: 1400e Operator Terminal
Serial Communications
Port
The RS-232 serial communications port can be connected to either
the development system for uploading/downloading application files,
or to a printer for printing screen images, alarm history and alarm
status reports, or alarm messages. Separate port settings can be
assigned for each of these purposes. The applicable printer port
settings are used automatically and are as follows, with the default in
brackets:
Baud Rates
300,1200, 2400, 4800, 9600, 19.2 kilobaud (9600)
Parity Types
Odd, Even, None (None)
Stop Bits
1, 2 (1)
Data Bits
7, 8 (8)
Handshake
Hardware, Software (X-ON, X-OFF), None (Software)
Auto Line Feed
Off, On (On)
Auto Form Feed
Off, On (On)
The factory defaults for file transfer are the same as the default
settings the development software will apply to the selected RS-232
port on your development system, so you don’t normally need to
change them.
File transfer settings are separate from the printer and are as follows:
PCMCIA Memory Card
Support
Publication 2711E-6.17 – November 1998
Baud Rates
300,1200, 2400, 9600, 19200 (9600)
Parity Types
Even, None (None)
Error
CRC, BCC (BCC)
Following are the PCMCIA memory cards supported by the
PanelView 1400e terminal in 200-ns or faster configuration.
Manufacturer
Part Number
Memory Capacity
Allen-Bradley
2711-NM11
256 K bytes
Allen-Bradley
2711-NM12
1 MB
Allen-Bradley
2711-NM13
2 MB
Allen-Bradley
2711-NM14
4 MB
Allen-Bradley
2711-NM15
8 MB
Specifications: 1400e Operator Terminal
Keyboard and Bar Code
Reader Support
C–7
Following are the keyboards supported by the PanelView 1400e
terminal.
Manufacturer
Part Number
Allen-Bradley
6189-KBM1
Allen-Bradley
6189-KBD1
Allen-Bradley
6189-KBE1
Following is the bar code reader supported by the PanelView 1400e
terminal.
AC Power
Manufacturer
Part Number
Allen-Bradley
2755HDG4 Series A, Revision C
Following are the ac power specifications for the PanelView 1400e
terminal.
Power Supply Type
Switching
Range
90–132, 180–264 V ac
automatic setting by the PanelView 1400e terminal to
match available power supply
Frequency Range
47–63 Hz
Power Consumption
Color terminal
75 W typical
100 W maximum
Volt Amps
Color terminal
180 VA typical
240 VA maximum
While the color terminal degausses, there is a 5.5-amp surge at
115 volts. At 230 V, there is an 11-amp surge that lasts less than
400 milliseconds. Automatic degauss occurs every time ac power is
re-applied to the terminal.
Fuses
PanelView 1400e terminals:
• Require one fuse for each ac line
• Have fuses the user can access from the rear of the terminal
• Accepts the following fuse type: BUSS GDC-3.15, 3.15 A,
250 V ac, 5 mm × 20 mm
!
ATTENTION: Fuses must be replaced by authorized
service personnel only. PanelView 1400e terminals
contain neutral fuses. Disconnect power before
servicing the unit.
Publication 2711E-6.17 – November 1998
C–8
Specifications: 1400e Operator Terminal
Character Set
PanelView 1400e terminals support the IBM character set for alarm,
local, and information messages.
User Memory
PanelView 1400e terminals support:
• 256K bytes of Flash memory for application file
• PCMCIA card slot of variable size (depends on user application
file)
RAM tests and Memory Checksum tests can be initiated in the
Terminal Diagnostics screen in Configuration mode.
Alarm Relay
•
•
•
•
•
Batteries
PanelView’s permanent, factory-installed lithium batteries have a
total lithium weight of not more than 1.0 gram. Batteries are not
burdened when ac power is applied to the terminal. The following
chart indicates battery life, with continuous exposure to the specified
temperatures, assuming ac power is applied to the terminal 8 hours a
day, 5 days a week. These calculations are based on battery life
specifications provided by the battery manufacturer and do not take
battery shelf life into account.
Form-C Contact
250 V ac Max, 8 amp continuous
30 V dc Max, 8 amp continuous
Minimum Voltage: 1 V dc
Minimum Current: 1 mA dc
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
+86° F (+30° C)
Greater than 10 years
+104° F (+40° C)
Greater than 10 years
+113° F (+45° C)
Greater than 10 years
+122° F (50° C)
10 years
+140° F (60° C)
7.5 years
Battery fail indications are displayed automatically.
Publication 2711E-6.17 – November 1998
Specifications: 1400e Operator Terminal
Time and Date Clock
C–9
• Display modes: AM/PM or 24-hour (hours, minutes, seconds);
•
•
•
•
•
optional show seconds, leading digit is zero or blank
Date display includes month, day, and year: order (MDY, DMY,
YMD), 2/4 digit year format (except fixed 2-digit for Alarm
History screen), leading digit is zero or blank
Time and date plus “day of week” can be transferred to the host
PLC
Time and date can be transferred from the host PLC to the
terminal to synchronize the terminal’s date and time
Battery-backed
Automatic leap year correction
The clock’s accuracy can vary by ±7 minutes per month over an
operating temperature range of 0° C to 60° C.
Temperature, Humidity,
and Altitude
The following are temperature, humidity, and altitude requirements
for the PanelView 1400e terminal.
Ambient Operating Temperature Limits
• Maximum: +50° C (+122° F)
• Minimum: 0° C (+32° F)
Storage Temperature Limits
• Minimum: -40° C (-40° F)
• Maximum: +85° C (+185° F)
Humidity
• Relative operating humidity (non-condensing)
– 0°to +30° C (+32°to +86° F) 95% humidity
– +30°to +40° C (+86° to +104° F) 75% humidity
– +40° to +50° C (+104° to +122° F) 40% humidity
• Relative non-operating humidity (non-condensing)
– -40° to +70° C (-40° to +158° F) 95% humidity
Maximum Altitude
• Non-operating or storage: 40,000 feet
• Operating: 10,000 feet
Publication 2711E-6.17 – November 1998
C–10
Specifications: 1400e Operator Terminal
Heat Generation
The following are heat generation requirements for the
PanelView 1400e color terminal.
Color Terminals
341 BTU/hour maximum
256 BTU/hour typical
Shock and Vibration
The following are shock and vibration specifications for the
PanelView 1400e terminal.
Shock Amplitudes
• Operating 15 G (Peak Acceleration)
• Non-operating 30 G (Peak Acceleration)
Vibration Amplitudes for Operating Units
Frequency range: 5 to 2000 Hz
• 5 to 57 Hz: .006–inch peak-to-peak displacement
• 58 to 2000 Hz: 1.0 G peak acceleration
Vibration Amplitudes for Non-Operating Units
Frequency range: 5 to 2000 Hz
• 5 to 57 Hz: .015–inch peak-to-peak displacement
• 58 to 2000 Hz: 2.5 G peak acceleration
Publication 2711E-6.17 – November 1998
Installing the PanelView Serial
Firmware Upgrade Utility
Installing SFU32 from
CD-ROM on Windows NT
or Windows 95
The Serial Firmware Upgrade Utility Version 5 (SFU32) is provided
on CD-ROM. The software installation program creates a directory
on your hard drive for the SFU32 and copies all necessary files to it.
By default, the drive and directory is C:\AB\PB1400E\SFU32. You
can change this default.
To install SFU32:
1. Start Windows NT or Windows 95. If you’re already in Windows,
close all open Windows applications.
2. Place the CD-ROM in the drive.
The CD-ROM should begin to run automatically. If it does not
start automatically, choose Run from the Start button and select
setup.exe from the CD-ROM drive; or select setup.exe from
Windows Explorer.
3. In the Welcome dialog box, choose Next.
4. If you are installing on Windows 95, the Select Version dialog
box appears. Select Version 5, and then choose Next.
If you are installing on Windows NT, the Select Version dialog
box does not appear. Version 5 is automatically selected.
5. In the Choose Applications dialog box, choose Serial Firmware
Upgrade as the application you want to install. You can choose
more than one application to install. Choose Next.
6. In the registration dialog box, enter your user name, company
name, and serial number. You can obtain registration information
from the software registration card that is in your
PanelBuilder 1400e package (A-B Catalog Number 2711E-ND1).
Choose Next.
7. In the confirmation dialog box, verify the user information you
have entered. Select Yes to proceed or No to edit the user
information.
8. In the Welcome dialog box for the Serial Firmware Upgrade
Utility, it recommends that you close all open Windows
applications. If you have done that, choose Next.
9. Choose the drive and directory in which the SFU32 will be
installed. By default, this is C:\AB\PB1400E\SFU32. To change
the destination drive or directory, type the new drive and/or
directory in the Program Files box. Choose Next.
Publication 2711E-6.17 – November 1998
D–2
Installing the PanelView Serial Firmware Upgrade Utility
10. Choose the program folder (program group) in which you want to
install the SFU32’s icons, which includes a Readme file icon, the
Upgrade Utility icon, and an Uninstall icon. By default, the icons
are installed in the PanelBuilder 1400e program folder. Choose
Next.
11. The setup utility shows a summary of the choices you made in the
preceding dialog boxes. To make any changes, choose the Back
button. Otherwise, choose Next to begin the installation.
Do not cancel the installation while it is in progress. If you want
to undo the installation, let the installation finish, and then use the
Uninstall Serial Firmware Upgrade Utility to remove all the
installed files and to update the registration.
12. When the installation is complete, remove the CD-ROM from the
drive.
Installing SFU from
CD-ROM on Windows 95
or Windows 3.x
The Serial Firmware Upgrade Utility Version 3 (SFU) software is
provided on CD-ROM. The software installation program creates a
directory on your hard drive for the Serial Firmware Upgrade Utility
and copies all necessary files to it. By default, the drive and directory
is C:\AB\PB1400e\SFU. You can change this default.
To install SFU:
1. Start Windows 95 or 3.x. If you’re already in Windows, close all
open Windows applications.
2. Place the CD-ROM in the drive.
The CD-ROM should begin to run automatically. If it does not
start automatically and you are running on Windows 95, choose
Run from the Start button and select setup.exe from the CD-ROM
drive; or select setup.exe from Windows Explorer.
If the CD-ROM does not start automatically and you are running
on Windows 3.x, choose Run from the File menu. In the Run
dialog box, type:
d:setup
where d is the drive containing the Serial Firmware Upgrade
Utility CD-ROM, and press Enter.
Publication 2711E-6.17 – November 1998
Installing the PanelView Serial Firmware Upgrade Utility
D–3
3. In the Welcome dialog box, choose Next.
4. If you are installing on Windows 95, the Select Version dialog
box appears. Choose Version 3, and then choose Next.
If you are installing on Windows 3.x, the Select Version dialog
box does not appear. Version 3 is automatically selected.
5. In the Choose Applications dialog box, choose Serial Firmware
Upgrade as the application you want to install. You can choose
more than one application to install. Choose Next.
6. In the Welcome dialog box for the Serial Firmware Upgrade
Utility, it recommends that you close all open Windows
applications. If you have done that, choose Next.
7. Choose the drive and directory in which the Serial Firmware
Upgrade Utility will be installed. By default, this is
C:\AB\PB1400e\SFU. To change the destination drive or
directory, type the new drive and/or directory in the Directory
box. Choose Next.
8. Choose the program folder (program group) in which you want to
install the Serial Firmware Upgrade Utility’s icons, which
includes a Readme file icon, the Utility file icon, and an Uninstall
icon. By default, the icons are installed in the PanelBuilder 1400e
program folder. Choose Next.
9. Follow the setup instructions as they appear on your screen.
To complete the setup, enter any required information when
prompted.
Do not cancel the installation while it is in progress. If you want
to cancel the installation, let the installation finish, and then use
the Uninstall Serial Firmware Upgrade Utility to remove all the
installed files.
10. When the installation is complete, remove the CD-ROM from the
drive.
For information on how to start and exit from the Serial Firmware
Upgrade Utility Version 3 (SFU), see the PanelView 1000e, 1200e,
and 1400e Operator Terminals User Manual (A-B Publication
Number 2711E-821).
Publication 2711E-6.17 – November 1998
D–4
Installing the PanelView Serial Firmware Upgrade Utility
Installing SFU32 from
Floppy Disks on Windows
NT or Windows 95
The Serial Firmware Upgrade Utility Version 5 (SFU32) software is
provided on two disks. Before installing the software, make a backup
copy of the disks. Store the original disks in a safe place, and install
the SFU32 from the copy.
The software installation program creates a directory on your hard
drive for the SFU32 and copies all necessary files to it. By default,
the drive and directory is C:\AB\PB1400E\SFU32. You can change
this default.
To install SFU32:
1. Start Windows NT or Windows 95. If you’re already in Windows,
close all open Windows applications.
2. Insert the floppy disk in the drive.
3. Choose Run from the Start button, and select setup.exe from the
floppy disk drive; or select setup.exe from Windows Explorer.
4. Close all applications, and then choose Next. The Serial
Firmware Upgrade Utility Installation Program runs
automatically.
5. Enter the required information.
6. Choose the drive and directory in which the SFU32 will be
installed. By default, this is C:\AB\PB1400E\SFU32. To change
the destination drive or directory, type the new drive and/or
directory in the Program Files box. Choose Next.
7. Choose the program folder (program group) in which you want to
install the SFU32’s icons, which includes a Readme file icon, the
Upgrade Utility icon, and an Uninstall icon. By default, the icons
are installed in the PanelBuilder 1400e program folder. Choose
Next.
8. Follow the setup instructions as they appear on your screen.
To complete the setup, enter any required information and insert
the second disk when prompted.
Do not cancel the installation while it is in progress. If you want
to undo the installation, let the installation finish, then use the
Uninstall Serial Firmware Upgrade Utility to remove all the
installed files and to update the registration.
9. When the installation is complete, remove the disk from the
drive.
Publication 2711E-6.17 – November 1998
Installing the PanelView Serial Firmware Upgrade Utility
Installing SFU from Floppy
Disks on Windows 95 or
Windows 3.x
D–5
The Serial Firmware Upgrade Utility Version 3 (SFU) software is
provided on two disks. Before installing the software, make a backup
copy of the disks. Store the original disks in a safe place, and install
the Serial Firmware Upgrade Utility from the copies.
The software installation program creates a directory on your hard
drive for the Serial Firmware Upgrade Utility and copies all
necessary files to it. By default, the drive and directory is
C:\AB\PB1400e\SFU. You can change this default.
To install SFU:
1. Start Windows 95 or 3.x. If you’re already in Windows, close all
open Windows applications.
2. Insert the floppy disk in the drive.
3. If you are running on Windows 95, choose Run from the Start
button, and select setup.exe from the floppy disk drive; or select
setup.exe from Windows Explorer.
If you are running on Windows 3.x, choose Run from the File
menu. In the Run dialog box, type:
a:setup
or b:setup
where a or b is the drive containing the Serial Firmware Upgrade
Utility disk, and then press Enter.
4. A dialog box appears, recommending you close all open
Windows applications. If you followed step 1, choose Next;
otherwise close all open Windows applications now. Choose
Next.
5. Choose the drive and directory in which the Serial Firmware
Upgrade Utility will be installed. By default, this is
C:\AB\PB1400e\SFU. To change the destination drive or
directory, type the new drive and/or directory in the Directory
box. Choose Next.
Publication 2711E-6.17 – November 1998
D–6
Installing the PanelView Serial Firmware Upgrade Utility
6. Choose the program folder (program group) in which you want to
install the Serial Firmware Upgrade Utility’s icons, which
includes a Readme file icon, the Utility file icon, and an Uninstall
icon. By default, the icons are installed in the PanelBuilder 1400e
program folder. Choose Next.
7. Follow the setup instructions as they appear on your screen.
To complete the setup, enter any required information and insert
the second disk when prompted.
Do not cancel the installation while it is in progress. If you want
to cancel the installation, let the installation finish, then use the
Uninstall Serial Firmware Upgrade Utility to remove all the
installed files.
8. When the installation is complete, remove the disk from the
drive.
For information on how to start and exit from the Serial Firmware
Upgrade Utility Version 3 (SFU), see the PanelView 1000e, 1200e,
and 1400e Operator Terminals User Manual (A-B Publication
Number 2711E-821).
Installing Additional
Communication Drivers
The Serial Firmware Upgrade Utility supports additional
communication drivers besides the core drivers (Remote I/O, DH+,
ControlNet KTCs, and ControlNet KTCx). If an additional driver is
required, a disk that contains an install and uninstall program is
supplied in the kit for that network driver.
To install an additional driver:
1. Close the Serial Firmware Upgrade Utility before you install the
driver.
2. Insert the floppy disk in the drive.
3. On Windows NT or Windows 95, click the Start button and then
choose Run.
On Windows 3.x, choose Run from the File menu of Program
Manager or File Manager.
4. In the Run dialog box, type:
a:setup
or b:setup
5. Follow the installation instructions as they appear on your screen.
When the registration dialog box appears, enter the registration
information that is provided in the kit for the network driver.
Publication 2711E-6.17 – November 1998
Installing the PanelView Serial Firmware Upgrade Utility
D–7
6. When the installation is complete, remove the disk from the
drive.
7. Start the Serial Firmware Upgrade Utility. The new driver is
displayed in the list of drivers.
Starting the PanelView
Serial Firmware Upgrade
Utility
This section describes how to start the Serial Firmware Upgrade
Utility Version 5 (SFU32) from Windows NT or Windows 95. The
functionality of the serial firmware upgrade utility is the same for
Windows NT and Windows 95.
To start the Serial Firmware Upgrade Utility from Windows NT or
Windows 95:
1. Click the Start button on the taskbar.
2. Choose Programs, and then choose PanelBuilder 1400e, or the
folder you specified when you installed the program.
3. Choose Serial Firmware Upgrade Utility.
Performing a Serial
Firmware Upgrade
After starting the Serial Firmware Upgrade Utility, the PanelView
Serial Firmware Upgrade Utility dialog box appears.
To perform a serial firmware upgrade:
1. Choose Upgrade Parameters.
2. Select Communications Drivers.
3. To initiate the PanelView firmware upgrade, click Start Upgrade.
For more information on how to configure parameters and initiate a
firmware upgrade, press F1 to open online help.
During the firmware upgrade, the host computer displays status
information. If the upgrade has been completed successfully, the
following message is displayed and the PanelView terminal reboots:
Terminal firmware upgraded successfully.
If the upgrade failed, the following message is displayed and the host
computer returns to the Serial Firmware Upgrade Utility dialog box:
Terminal firmware upgrade failed.
Publication 2711E-6.17 – November 1998
D–8
Installing the PanelView Serial Firmware Upgrade Utility
Exiting from the PanelView
Serial Firmware Upgrade
Utility
When you have finished transferring the firmware, you can exit the
Serial Firmware Upgrade Utility.
To exit from the Serial Firmware Upgrade Utility:
"
Publication 2711E-6.17 – November 1998
Click the Exit button in the dialog box.
Numbers
1000e operator terminals
connecting an external alarm relay, 2–14
installing, 2–1
mounting options, 2–5
specifications
alarm relay, A–8
altitude, A–9
ambient operating temperature limits,
A–9
backlight life, A–4
batteries, A–8
character sets, A–8
color units, A–5
CRT display, A–4
custom legends, A–3
design standards, A–2
EMC Directive, A–2
EMC standards, A–1
environmental standards, A–1
front panel design, A–3
fuses, A–8
humidity, A–9
keypad terminal weights, A–3
keypad terminals, A–3
Low Voltage Directive, A–2
memory, A–8
NEMA Standards, A–1, A–2
PCMCIA memory cards, A–7
PLC Remote I/O communications, A–5
RAM tests, A–8
RS-232 port, A–6
safety standards approvals, A–1
shock and vibration, A–10
storage temperature limits, A–9
temperature, A–9
terminal weights, A–3
time and date clock, A–9
touch screen terminal weights, A–3
touch screen terminals, A–4
user memory, A–8
1200e operator terminals
connecting an external alarm relay, 3–14
degauss option, 5–50
dimensions, 2–3, 2–4, 3–3
installing, 3–1
mounting options, 3–5
rear panel, 3–1
specifications
AC power, B–6
altitude, B–8
ambient operating temperature limits,
B–8
batteries, B–7
character sets, B–6
color units, B–3
CRT display, B–3
custom legends, B–2
Data Highway Plus Communications,
B–4
EMC standards, B–1
environmental standards, B–1
front panel design, B–2
fuses, B–6
heat generation, B–8
humidity, B–8
keypad terminal weights, B–2
keypad terminals, B–2
memory, B–6
NEMA Standards, B–1
PCMCIA memory cards, B–5
PLC Remote I/O communications, B–4
RAM tests, B–6
RS-232 port, B–5
safety standards approvals, B–1
shock and vibration, B–9
storage temperature limits, B–8
temperature, B–8
terminal weights, B–2
time and date clock, B–7
touch screen terminal weights, B–2
touch screen terminals, B–3
user memory, B–6
1400e operator terminals
connecting an external alarm relay, 4–12
dimensions, 4–3
installing, 4–1
mounting options, 4–5
rear panel, 4–1
specifications
AC power, C–7
alarm relay, C–8
altitude, C–9
ambient operating temperature limits,
C–9
batteries, C–8
character sets, C–8
color units, C–4
CRT display, C–4
custom legends, C–3
design standards, C–2
EMC Directive, C–2
Publication 2711E-6.17 – November 1998
I–2
Index
EMC standards, C–1
environmental standards, C–1
front panel design, C–3
fuses, C–7
heat generation, C–10
humidity, C–9
keypad terminal weights, C–3
keypad terminals, C–3
Low Voltage Directive, C–2
memory, C–8
NEMA Standards, C–1, C–2
PCMCIA memory cards, C–6
PLC Remote I/O communications, C–5
RAM tests, C–8
RS-232 port, C–6
safety standards approvals, C–1
shock and vibration, C–10
storage temperature limits, C–9
temperature, C–9
terminal weights, C–3
time and date clock, C–9
touch screen terminal weights, C–3
touch screen terminals, C–4
user memory, C–8
Alarm settings, 5–35, 5–36
Align screen button, 5–41
Altitude
1000e operator terminals, A–9
1200e operator terminals, B–8
1400e operator terminals, C–9
Ambient operating temperature limits
1000e operator terminals, A–9
1200e operator terminals, B–8
1400e operator terminals, C–9
Application Checksum test, 5–50
Application File Comment field, 5–57
Application file storage, 3–17
displayed on Terminal Information
screen, 5–57
1775-S4A Remote Scanner/Distribution
panel, 1–15
Application files
downloading, 6–2
multiple, 5–19
running, 6–3
selecting, 5–19
storage locations, 5–19
transfer types, 5–4
transferring, 5–4
6008-SI IBM PC I/O Scanner, 1–15
Application screens, printing, 5–43
6008-SV VME I/O Scanner, 1–16
Application Startup screen, 5–26
6008-SQ DEC Q-BUS I/O Scanner, 1–16
Auto Restart option, 5–14
6200 software, 6–1
Automatic degauss
1200e operator terminals, B–4
1400e operator terminals, C–4
1747-SN I/O Subscanner Module, 1–15
1771-SN I/O Subscanner Module, 1–14,
1–15
1772-SD2 Scanner/Distribution panel, 1–15
A
AC power
1200e operator terminals, B–6
1400e operator terminals, C–7
Accessories, 1–1
B
Backlight intensity, 2–11
Address source, 5–14
Backlight life, 1000e operator terminals,
A–4
Adjusting audio volume, 5–35
Backlight replacement, 7–3
Adjusting contrast and brightness, 3–10,
4–8
Batteries
1000e operator terminals, A–8
failure indications, A–8
1200e operator terminals, B–7
failure indications, B–7
1400e operator terminals, C–8
failure indications, C–8
Alarm connector, voltage range, 2–14, 3–14
Alarm history records, 5–35
Alarm messages, 5–60
Alarm relay, 5–35
1000e operator terminals, A–8
1200e operator terminals, B–7
1400e operator terminals, C–8
Publication 2711E-6.17 – November 1998
connecting to 1000e operator terminals,
2–14
connecting to 1200e operator terminals,
3–14
connecting to 1400e operator terminals,
4–12
Battery test, 5–2, 5–51
Battery-backed RAM, testing, 5–51
Index
Baud rate, 5–55
default, 5–7, 5–23
displayed on screen, 5–23
CRT intensity, controlling, 7–1
Block transfer file definitions, viewing, 5–21
Custom legends
1000e operator terminals, A–3
1200e operator terminals, B–2
1400e operator terminals, C–3
C
Character sets
1000e operator terminals, A–8
1200e operator terminals, B–6
1400e operator terminals, C–8
Cleaning
enclosure, 7–1
keypad, 7–1
touch screen, 7–1
Clear button, 5–59
Color units
1000e operator terminals, A–5
1200e operator terminals, B–3
1400e operator terminals, C–4
Communication problems, PLC, 8–7
Data Highway Plus, 8–8, 8–9
Communication settings, matching, 6–2
Configuration mode, 5–1
starting up PanelView terminals in, 5–2
Configuration mode menu, 5–2
Configuration settings
verifying, 8–1
viewing, 8–1
Configure and Run modes, 2–11, 3–11, 4–9
Configure mode, to test terminal, 6–1
Configuring, PanelView operator terminals,
5–1
Current application file, information about,
5–57
Cutout
template, 2–5, 3–5
tools required, 2–5, 3–5, 4–5
D
Data Highway Plus
1200e operator terminals, B–4
description, 1–16
testing terminal, 6–1
Data transmission, errors, 5–7
Dataliner message display, 5–47
default settings, 5–48
Degauss option, 5–50
Degaussing
automatic
1200e operator terminals, B–4
1400e operator terminals, C–4
operator terminals, 7–2
Demagnetizing the CRT, 5–50
DEMO files, 6–1
Design standards
1000e operator terminals, A–2
1400e operator terminals, C–2
DH+. See Data Highway Plus
Contrast and brightness controls, 3–10, 4–8
Dimensions
1000e operator terminals, 2–3
1200e operator terminals, 3–3
1400e operator terminals, 4–3
ControlNet, 1–17
Direct ControlNet link, 5–16
Copying application files, 5–9
Direct DH+ link, 5–16
CRT display
1000e operator terminals, A–4
1200e operator terminals, B–3
1400e operator terminals, C–4
Disabling button or alarm audio, 5–35
Connecting the PLC, 4–13, 6–3
I–3
Downloading, application files, 5–4, 6–2
Publication 2711E-6.17 – November 1998
I–4
Index
E
EMC Directive
1000e operator terminals, A–2
1400e operator terminals, C–2
EMC standards
1000e operator terminals, A–1
1200e operator terminals, B–1
1400e operator terminals, C–1
Emergency stop buttons, 6–4
Environmental standards
1000e operator terminals, A–1
1200e operator terminals, B–1
1400e operator terminals, C–1
Erasing data, 5–12
Exit button (F21), 5–52
Exiting from Serial Firmware Upgrade
Utility, D–8
Extended system memory, 5–56
Fuses
1000e operator terminals, A–8
1200e operator terminals, B–6
1400e operator terminals, C–7
American, B–6
Europe, B–6
G
Global tab, 5–28
H
Heat generation
1200e operator terminals, B–8
1400e operator terminals, C–10
Humidity
1000e operator terminals, A–9
1200e operator terminals, B–8
1400e operator terminals, C–9
External alarm, 5–35
External alarm relay
connecting to 1000e operator terminals,
2–14
connecting to 1200e operator terminals,
3–14
connecting to 1400e operator terminals,
4–12
F
Fan filter
changing, 7–2
replacement part, 7–2
Fault messages
major, 8–1
minor, 8–3
File transfers, 5–8
Firmware, integrity test, 5–1
Format Destination button, 5–12
Formatting reports, 5–46, 5–50
Front panel design
1000e operator terminals, A–3
1200e operator terminals, B–2
1400e operator terminals, C–3
Publication 2711E-6.17 – November 1998
I
I/O scanners, publications, P–2
Information messages, 5–60
Initial states, 5–26
Initial values, 5–26, 5–55
Installing
1000e operator terminals, 2–1
1200e operator terminals, 3–1
1400e operator terminals, 4–1
Internal clock, 5–32
K
Keypad terminal weights
1000e operator terminals, A–3
1200e operator terminals, B–2
1400e operator terminals, C–3
Keypad terminals
1000e dimensions, 2–3
1200e dimensions, 3–3
1400e dimensions, 4–3
about, 1–6
Function Keys button, Terminal
Diagnostics, 5–51
specifications, A–3, B–2, C–3
Index
L
N
Legend kit, 1–6
NEMA 4X rating, 3–6
Load Application Initial Values, 5–55
Logic board, providing access, 4–5
NEMA standards
1000e operator terminals, A–1, A–2
1200e operator terminals, B–1
1400e operator terminals, C–1, C–2
Logix55xx, 1–14, 1–16, 1–18
Network File Transfer tab, 5–13, 5–16
Local messages, 5–60
Low Voltage Directive
1000e operator terminals, A–2
1400e operator terminals, C–2
I–5
O
Objects, retentive, testing, 6–4
M
Magnetic fields, avoiding, 7–2
Operating modes, 5–1
Operator access codes, 5–27
Major Fault mode, 5–58
Major Terminal Fault window, 5–58
Memory
1000e operator terminals, A–8
1200e operator terminals, B–6
1400e operator terminals, C–8
Memory card
drive, 5–9
slot at back of 1200e operator terminal,
2–17, 3–17
transfers, 5–9
upgrade, 5–56
Memory Card tab, 5–10
Memory cards
1000e operator terminals, A–7
1200e operator terminals, B–5
1400e operator terminals, C–6
Messages
fault, 8–1, 8–3
mistake, 8–4
Minor Terminal Fault window, 5–59
Mistake messages, 5–59, 8–4
Mode select keyswitch, 2–11, 3–11, 4–9
setting for power up, 5–1
Modes
Configure, 5–1
Run, 5–1
Mounting clips, 2–5, 3–5
Mounting options
1000e operator terminals, 2–5
1200e operator terminals, 3–5
1400e operator terminals, 4–5
P
PanelBuilder 1400e Configuration Software,
about, 1–11
PanelView operator terminals, configuring,
5–1
Parity, 5–7
Pass-Through
Address Source, 5–14
Control Byte, 5–23
default settings, 5–14
parameters, 5–13
Pass-Through application file transfers,
5–13
PCMCIA. See Memory cards
Performing a Serial Firmware Upgrade, D–7
PLC, 1–14, 5–1, 5–35
communicating with terminal, Run mode,
2–11, 3–11, 4–9
connecting to 1000e operator terminals,
2–15
connecting to 1200e operator terminals,
3–15
connecting to 1400e operator terminals,
4–13
connecting to a terminal, 6–3
publications, P–2
requesting screen prints, 5–46
required for Pass-Through, 5–15
PLC communication problems, 8–7
Data Highway Plus, 8–8, 8–9
Mounting studs, 3–5
Publication 2711E-6.17 – November 1998
I–6
Index
PLC Remote I/O communications
1000e operator terminals, A–5
1200e operator terminals, B–4
1400e operator terminals, C–5
PLC-5 family, rack address ranges, 1–14,
1–16
PLC-5C family, 1–18
PLC-5C15 family, 1–18
PLC-5C programmable controllers,
ControlNet PLCs, 1–18
PLC-5C15 programmable controllers,
ControlNet PLCs, 1–18
PLC-2 family, rack address ranges, 1–15,
1–16
PLC-3 family, rack address ranges, 1–15,
1–16
POST. See Power On Self–Test
Power
connecting to 1000e operator terminals,
2–11
connecting to 1200e operator terminals,
3–11
connecting to 1400e operator terminals,
4–9
Problems
fault messages
major, 8–1
minor, 8–3
mistake messages, 8–4
PLC communication, 8–7
Data Highway Plus, 8–8, 8–9
Programmable Controllers. See PLC
Publications, P–2
R
Rack assignment, Remote I/O rack
assignment, 5–21
Rack assignments, viewing, 5–21
RAM tests
1000e operator terminals, A–8
1200e operator terminals, B–6
1400e operator terminals, C–8
Rear panel
1200e operator terminals, 3–1
1400e operator terminals, 4–1
Remote DH+ connector, 4–13
Remote I/O, 1–14
Power connector
1000e operator terminals, 2–12
1200e operator terminals, 3–12
Remote I/O connector, 2–15, 3–15, 4–13
Power On Self-Test, 5–1
Replacement kits, 1–4
Power up
terminal, 5–1
tests, 5–1
Restore Defaults screen, 5–54
Power-up screen, for application, 6–3
RS-232 port, 2–12, 3–12, 4–11
1000e operator terminals, A–6
1200e operator terminals, B–5
1400e operator terminals, C–6
Printer
cable, 5–9, 5–47
default settings, 5–45
errors, 5–46
Dataliner
for 1000e operator terminals, 2–13
for 1200e operator terminals, 3–14
for 1400e operator terminals, 4–12
Remote keyswitch assembly, 3–11, 4–9
Retentive objects, testing, 6–4
RIO Pass-Through, 5–14
Run mode, 5–1, 5–9
set mode select keyswitch, 6–3
S
Printer cable
for 1000e operator terminals, 2–13
for 1200e operator terminals, 3–13
for 1400e operator terminals, 4–11
Safety standards approvals
1000e operator terminals, A–1
1200e operator terminals, B–1
1400e operator terminals, C–1
Printing
application screens, 5–43
displayed alarms, 5–43
log of alarm messages, 5–43
priorities, 5–46
Screen
aligning on a 1200e terminal, 5–41
enabling or disabling security, 5–29
power-up, 6–3
requesting prints, 5–46
saver, 5–40, 5–41
Printing screens from terminal, 5–46
Security screen, 5–27
Select Application screen, 5–20
Publication 2711E-6.17 – November 1998
Index
Serial communications port
1000e operator terminals, A–6
1200e operator terminals, B–5
1400e operator terminals, C–6
Serial firmware upgrade, 5–56
Serial Firmware Upgrade Utility
exiting, D–8
install an additional driver, D–6
performing, D–7
starting, D–7
from Windows, D–7
Serial port, configuring, 5–7
Serial printer, connecting to 1400e operator
terminals, 4–11
Setting time and date, 5–30
Settings, changing, 5–7
Shock and vibration
1000e operator terminals, A–10
1200e operator terminals, B–9
1400e operator terminals, C–10
SLC-RIO connection, 1–15
SLC-5 family, rack address ranges, 1–15,
1–16
Specifications
1000e operator terminals
alarm relay, A–8
altitude, A–9
ambient operating temperature limits,
A–9
backlight life, A–4
batteries, A–8
character sets, A–8
color units, A–5
CRT display, A–4
custom legends, A–3
design standards, A–2
EMC Directive, A–2
EMC standards, A–1
environmental standards, A–1
front panel design, A–3
fuses, A–8
humidity, A–9
keypad terminal weights, A–3
keypad terminals, A–3
Low Voltage Directive, A–2
memory, A–8
NEMA Standards, A–1, A–2
PCMCIA memory cards, A–7
PLC Remote I/O communications, A–5
RAM tests, A–8
RS-232 port, A–6
safety standards approvals, A–1
serial communications port, A–6
shock and vibration, A–10
storage temperature limits, A–9
I–7
temperature, A–9
terminal weights, A–3
time and date clock, A–9
touch screen terminal weights, A–3
touch screen terminals, A–4
user memory, A–8
1200e operator terminals
altitude, B–8
ambient operating temperature limits,
B–8
batteries, B–7
character sets, B–6
color units, B–3
CRT display, B–3
custom legends, B–2
Data Highway Plus Communications,
B–4
EMC standards, B–1
environmental standards, B–1
front panel design, B–2
fuses, B–6
heat generation, B–8
humidity, B–8
keypad terminal weights, B–2
keypad terminals, B–2
memory, B–6
NEMA Standards, B–1
PCMCIA memory cards, B–5
PLC Remote I/O communications, B–4
RAM tests, B–6
RS-232 port, B–5
safety standards approvals, B–1
serial communications port, B–5
shock and vibration, B–9
storage temperature limits, B–8
temperature, B–8
terminal weights, B–2
time and date clock, B–7
touch screen terminal weights, B–2
touch screen terminals, B–3
user memory, B–6
1400e operator terminals
alarm relay, C–8
altitude, C–9
ambient operating temperature limits,
C–9
batteries, C–8
character sets, C–8
color units, C–4
CRT display, C–4
custom legends, C–3
design standards, C–2
EMC Directive, C–2
EMC standards, C–1
environmental standards, C–1
front panel design, C–3
fuses, C–7
heat generation, C–10
Publication 2711E-6.17 – November 1998
I–8
Index
humidity, C–9
keypad terminal weights, C–3
keypad terminals, C–3
Low Voltage Directive, C–2
memory, C–8
NEMA Standards, C–1, C–2
PCMCIA memory cards, C–6
PLC Remote I/O communications, C–5
RAM tests, C–8
RS-232 port, C–6
safety standards approvals, C–1
serial communications port, C–6
shock and vibration, C–10
storage temperature limits, C–9
temperature, C–9
terminal weights, C–3
time and date clock, C–9
touch screen terminal weights, C–3
touch screen terminals, C–4
user memory, C–8
Start-up options
ControlNet (unscheduled), 5–27
DH+, 5–27
Ethernet, 5–27
Other networks, 5–27
ControlNet (scheduled), 5–26
Remote I/O, 5–26
Starting Serial Firmware Upgrade Utility
from Windows 95, D–7
from Windows NT, D–7
Starting up, PanelView terminals in
configuration mode, 5–2
Station address, 5–23, 5–25
Station number, 5–55
Storage temperature limits
1000e operator terminals, A–9
1200e operator terminals, B–8
1400e operator terminals, C–9
Stuck cell timeout, 5–38
Switching modes
1000e operator terminals, 2–11
1200e operator terminals, 3–11
1400e operator terminals, 4–9
System errors, 5–60
Publication 2711E-6.17 – November 1998
T
T30 panel cutout, 3–6
Temperature
1000e operator terminals, A–9
1200e operator terminals, B–8
1400e operator terminals, C–9
Terminal Configuration screen, 5–2
Terminal defaults, restoring, 5–54
Terminal Diagnostics screen, 5–50
function keys, 5–51
Terminal Information button, 5–57
Terminal network settings, viewing, 8–1
Terminal Network Setup screen, 5–21,
5–23, 5–24
Terminal product line, 1–1
Terminal Response screen, 5–33
Terminal weights
1000e operator terminals, A–3
1200e operator terminals, B–2
1400e operator terminals, C–3
Test Alignment button, 5–42
Test Relay button, 5–37
Testing
retentive objects, 6–4
system, 6–4
the terminal, 5–50
Time and date clock
1000e operator terminals, A–9
1200e operator terminals, B–7
1400e operator terminals, C–9
Time and Date tab, 5–30
Tools
for installing 1200e operator terminals,
3–5
for installing 1400e operator terminals,
2–5, 4–5
Touch cells, 1–10
Touch screen terminal weights
1000e operator terminals, A–3
1200e operator terminals, B–2
1400e operator terminals, C–3
Index
Touch screen terminals
1000e dimensions, 2–4
1000e specifications, A–4
1200e dimensions, 3–3
1200e specifications, B–3
1400e dimensions, 4–3
1400e specifications, C–4
about, 1–9
Touch Cells test, 5–51
Transfer Application screen, doing serial
transfers, 5–7
Transfer Setup screen, 5–6
Troubleshooting
fault messages
major, 8–1
minor, 8–3
mistake messages, 8–4
PLC communication problems, 8–7
Data Highway Plus, 8–8, 8–9
Upload/Download cable, 2–12, 3–12, 4–11,
5–5
Uploading, application files, 5–4
User memory
1000e operator terminals, A–8
1200e operator terminals, B–6
1400e operator terminals, C–8
User RAM test, 5–51
V
Verifying
configuration settings, 8–1
terminal network settings, 8–1
Viewing
block transfer file definitions, 5–21, 5–23,
5–24
configuration settings, 8–1
rack assignments, 5–21, 5–23, 5–24
terminal network settings, 8–1
U
Upgrade Firmware screen, initiate serial
firmware upgrade, 5–55
Upgrading firmware, 5–55
I–9
W
Watchdog test, 5–2
Wire routing, A–3, C–3
Publication 2711E-6.17 – November 1998
Rockwell Automation helps its customers receive a superior return on their investment by bringing
together leading brands in industrial automation, creating a broad spectrum of easy-to-integrate
products. These are supported by local technical resources available worldwide, a global network
of system solutions providers, and the advanced technology resources of Rockwell.
Worldwide representation.
Argentina • Australia • Austria • Bahrain • Belgium • Bolivia • Brazil • Bulgaria • Canada • Chile • China, People’s Republic of • Colombia • Costa Rica • Croatia • Cyprus
Czech Republic • Denmark • Dominican Republic • Ecuador • Egypt • El Salvador • Finland • France • Germany • Ghana • Greece • Guatemala • Honduras • Hong Kong
Hungary • Iceland • India • Indonesia • Iran • Ireland • Israel • Italy • Jamaica • Japan • Jordan • Korea • Kuwait • Lebanon • Macau • Malaysia • Malta • Mexico • Morocco
The Netherlands • New Zealand • Nigeria • Norway • Oman • Pakistan • Panama • Peru • Philippines • Poland • Portugal • Puerto Rico • Qatar • Romania • Russia • Saudi
Arabia • Singapore • Slovakia • Slovenia • South Africa, Republic of • Spain • Sweden • Switzerland • Taiwan • Thailand • Trinidad • Tunisia • Turkey • United Arab Emirates
United Kingdom • United States • Uruguay • Venezuela
Rockwell Automation Headquarters, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414 382-2000 Fax: (1) 414 382-4444
Rockwell Automation European Headquarters, Avenue Hermann Debroux, 46, 1160 Brussels, Belgium, Tel: (32) 2 663 06 00, Fax: (32) 2 663 06 40
Rockwell Automation Asia Pacific Headquarters, 27/F Citicorp Centre, 18 Whitfield Road, Causeway Bay, Hong Kong, Tel: (852) 2887 4788, Fax: (852) 2508 1846
World Wide Web: http://www.ab.com
Publication 2711E-6.17 – November 1998
41061-082-01(A)
Copyright 1998 Allen-Bradley Company, Inc. Printed in Canada
">