KINO-9453 Motherboard User Manual
KINO-9453 Motherboard User Manual
Page i
KINO-9453 Mini-ITX Motherboard
Revision
MODEL
KINO-9453 Socket 479 Intel Motherboard
Revision Number
Description
Date of Issue
1.0
Initial release
April 2007
Page ii
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
IBM PC is a registered trademark of International Business Machines Corporation. INTEL
is a registered trademark of INTEL Corporation. Other product names mentioned herein
are used for identification purposes only and may be trademarks and/or registered
trademarks of their respective owners.
Page iii
KINO-9453 Mini-ITX Motherboard
Packing List
NOTE:
If any of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the KINO-9453 from or contact an IEI sales
representative directly. To contact an IEI sales representative, please
send an email to [email protected]
The items listed below should all be included in the KINO-9453 package.
1 x KINO-9453 single board computer
1 x IDE cable
1 x SATA power cable
2 x SATA cables
1 x Dual RS-232 cable
1 x I/O shielding
1 x Mini jumper pack
1 x Utility CD
1 x QIG (quick installation guide)
Images of the above items are shown in Chapter 3.
Page iv
Table of Contents
1
INTRODUCTION..................................................................................................... 1
1.1 INTRODUCTION .......................................................................................................... 2
1.1.1 KINO-9453 Benefits........................................................................................... 2
1.1.2 KINO-9453 Features.......................................................................................... 2
1.2 KINO-9453 OVERVIEW ............................................................................................. 3
1.2.1 KINO-9453 Overview Photo.............................................................................. 3
1.2.2 KINO-9453 Peripheral Connectors and Jumpers ............................................. 4
1.2.3 Technical Specifications..................................................................................... 5
2
DETAILED SPECIFICATIONS ............................................................................. 7
2.1 OVERVIEW ................................................................................................................. 8
2.2 DIMENSIONS .............................................................................................................. 8
2.2.1 Board Dimensions.............................................................................................. 8
2.2.2 External Interface Panel Dimensions ................................................................ 9
2.3 DATA FLOW ................................................................................................................ 9
2.4 COMPATIBLE PROCESSORS ........................................................................................11
2.4.1 Compatible Processor Overview ......................................................................11
2.4.2 Supported Processors .......................................................................................11
2.5 INTEL® 945GM NORTHBRIDGE CHIPSET.................................................................. 12
2.5.1 Intel® 945GM Overview................................................................................... 12
2.5.2 Intel® 945GM Memory Support ....................................................................... 12
2.5.3 Intel® 945GM Integrated Graphics ................................................................. 13
2.5.3.1 Intel® 945GM Analog CRT Support ......................................................... 13
2.5.3.2 Intel® 945GM LVDS Support ................................................................... 14
2.5.3.3 Intel® 945GM SDVO Support .................................................................. 14
2.5.4 Intel® 945GM Direct Media Interface (DMI) .................................................. 14
2.6 INTEL® ICH7M SOUTHBRIDGE CHIPSET .................................................................. 14
2.6.1 Intel® ICH7M Overview................................................................................... 14
2.6.2 Intel® ICH7M Audio Codec ’97 Controller ..................................................... 15
2.6.3 Intel® ICH7M IDE Interface............................................................................ 16
2.6.4 Intel® ICH7M Low Pin Count (LPC) Interface ............................................... 16
Page v
KINO-9453 Mini-ITX Motherboard
2.6.5 Intel® ICH7M PCI Interface ............................................................................ 16
2.6.6 Intel® ICH7M Real Time Clock........................................................................ 17
2.6.7 Intel® ICH7M SATA Controller........................................................................ 17
2.6.8 Intel® ICH7M USB Controller......................................................................... 17
2.7 PCIE BUS COMPONENTS .......................................................................................... 17
2.7.1 PCIe Bus Overview .......................................................................................... 17
2.7.2 Broadcom PCI Express GbE interface............................................................. 18
2.8 LPC BUS COMPONENTS ........................................................................................... 18
2.8.1 LPC Bus Overview........................................................................................... 18
2.8.2 BIOS Chipset.................................................................................................... 18
2.8.3 Super I/O chipset.............................................................................................. 19
2.8.3.1 Super I/O LPC Interface ........................................................................... 19
2.8.3.2 Super I/O 16C550 UARTs ........................................................................ 19
2.8.3.3 Super I/O Enhanced Hardware Monitor ................................................... 20
2.8.3.4 Super I/O Fan Speed Controller................................................................ 20
2.8.3.5 Super I/O Keyboard Controller................................................................. 20
2.9 ENVIRONMENTAL AND POWER SPECIFICATIONS ....................................................... 20
2.9.1 System Monitoring ........................................................................................... 20
2.9.2 Operating Temperature and Temperature Control........................................... 21
2.9.3 Power Consumption......................................................................................... 22
3
UNPACKING .......................................................................................................... 23
3.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 24
3.2 UNPACKING.............................................................................................................. 24
3.2.1 Unpacking Precautions.................................................................................... 24
3.3 UNPACKING CHECKLIST ........................................................................................... 25
3.3.1 Package Contents............................................................................................. 25
3.3.2 Optional Items.................................................................................................. 26
4
CONNECTOR PINOUTS...................................................................................... 29
4.1 PERIPHERAL INTERFACE CONNECTORS .................................................................... 30
4.1.1 KINO-9453 Layout........................................................................................... 30
4.1.2 Peripheral Interface Connectors ..................................................................... 31
4.1.3 External Interface Panel Connectors............................................................... 32
4.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 32
Page vi
4.2.1 Fan Connectors................................................................................................ 32
4.2.2 Front Panel Connector .................................................................................... 33
4.2.3 Digital Input/Output Connector....................................................................... 34
4.2.4 IDE Connector ................................................................................................. 35
4.2.5 LCD Backlight Connector................................................................................ 37
4.2.6 LVDS LCD connector ...................................................................................... 38
4.2.7 Mini PCI Slot ................................................................................................... 40
4.2.8 Power Connector ............................................................................................. 41
4.2.9 14-Pin Serial Port Connectors......................................................................... 42
4.2.10 10-Pin Serial Port Connectors....................................................................... 43
4.2.11 SATA Drive Connectors.................................................................................. 44
4.2.12 SPDIF Connector........................................................................................... 45
4.2.13 Internal USB Connectors............................................................................... 46
4.3 EXTERNAL INTERFACE CONNECTORS ....................................................................... 47
4.3.1 Audio Connectors............................................................................................. 48
4.3.2 CRT Connector ................................................................................................ 48
4.3.3 DVI Connector ................................................................................................. 49
4.3.4 Ethernet Connectors ........................................................................................ 50
4.3.5 Keyboard/Mouse Connector ............................................................................ 51
4.3.6 Serial Port Connectors .................................................................................... 52
4.3.7 USB Connector ................................................................................................ 53
5
INSTALLATION .................................................................................................... 55
5.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 56
5.2 INSTALLATION CONSIDERATIONS ............................................................................. 57
5.2.1 Installation Notices .......................................................................................... 57
5.2.2 Installation Checklist ....................................................................................... 58
5.3 CPU, CPU COOLING KIT AND DIMM INSTALLATION ............................................. 59
5.3.1 Socket 479 CPU Installation............................................................................ 59
5.3.2 Cooling Kit CF-479B-RS Installation.............................................................. 62
5.3.3 DIMM Installation ........................................................................................... 64
5.4 JUMPER SETTINGS .................................................................................................... 65
5.4.1 Clear CMOS Jumper........................................................................................ 66
5.4.2 COM 3 Function Select Jumper....................................................................... 67
5.4.3 LVDS Voltage Selection.................................................................................... 68
Page vii
KINO-9453 Mini-ITX Motherboard
5.5 CHASSIS INSTALLATION ........................................................................................... 70
5.5.1 Airflow.............................................................................................................. 70
5.5.2 Motherboard Installation................................................................................. 70
5.6 INTERNAL PERIPHERAL DEVICE CONNECTIONS........................................................ 71
5.6.1 Peripheral Device Cables ................................................................................ 71
5.6.2 IDE Cable Connection..................................................................................... 71
5.6.3 Dual RS-232 Cable Connection....................................................................... 72
5.6.4 SATA Drive Connection ................................................................................... 73
5.7 EXTERNAL PERIPHERAL INTERFACE CONNECTION ................................................... 75
5.7.1 Audio Connection............................................................................................. 75
5.7.2 RJ-45 Ethernet Connection.............................................................................. 76
5.7.3 USB Connection............................................................................................... 77
5.7.4 VGA Monitor Connection ................................................................................ 78
5.7.5 Serial Device Connection ................................................................................ 79
5.7.6 PS/2 Keyboard/Mouse Connection .................................................................. 80
6
AMI BIOS................................................................................................................ 83
6.1 INTRODUCTION ........................................................................................................ 84
6.1.1 Starting Setup................................................................................................... 84
6.1.2 Using Setup ...................................................................................................... 84
6.1.3 Getting Help..................................................................................................... 85
6.1.4 Unable to Reboot After Configuration Changes.............................................. 85
6.1.5 BIOS Menu Bar................................................................................................ 85
6.2 MAIN ....................................................................................................................... 86
6.3 ADVANCED ............................................................................................................... 87
6.3.1 CPU Configuration.......................................................................................... 88
6.3.2 IDE Configuration ........................................................................................... 89
6.3.2.1 IDE Master, IDE Slave ............................................................................. 92
6.3.3 Super IO Configuration.................................................................................... 96
6.3.4 Hardware Health Configuration.................................................................... 100
6.3.5 ACPI Configuration ....................................................................................... 105
6.3.5.1 General ACPI Configuration................................................................... 105
6.3.6 APM Configuration........................................................................................ 107
6.3.7 Remote Access Configuration ........................................................................ 109
6.3.8 USB Configuration..........................................................................................113
Page viii
6.3.8.1 USB Mass Storage Device Configuration................................................116
6.4 PCI/PNP .................................................................................................................118
6.5 BOOT ..................................................................................................................... 124
6.5.1 Boot Settings Configuration........................................................................... 125
6.5.2 Boot Device Priority ...................................................................................... 127
6.5.3 Removable Drives .......................................................................................... 129
6.6 SECURITY............................................................................................................... 130
6.7 CHIPSET ................................................................................................................. 131
6.7.1 NorthBridge Configuration............................................................................ 132
6.7.1.1 Video Function Configuration ................................................................ 133
6.7.2 SouthBridge Chipset Configuration............................................................... 136
6.8 EXIT ....................................................................................................................... 138
7
DRIVER INSTALLATION.................................................................................. 141
7.1 AVAILABLE SOFTWARE DRIVERS ............................................................................ 142
7.2 DRIVER CD AUTO-RUN .......................................................................................... 142
7.3 CHIPSET DRIVER INSTALLATION............................................................................. 143
7.4 INTEL GRAPHICS MEDIA ACCELERATOR DRIVER ................................................... 148
7.5 BROADCOM LAN DRIVER (FOR GBE LAN) INSTALLATION .................................. 154
7.6 REALTEK HD AUDIO DRIVER (ALC883) INSTALLATION ....................................... 160
7.6.1 BIOS Setup ..................................................................................................... 160
7.6.2 Driver Installation ......................................................................................... 160
7.7 REALTEK AC`97 AUDIO DRIVER (ALC665) INSTALLATION .................................. 164
7.7.1 BIOS Setup ..................................................................................................... 164
7.7.2 Driver Installation ......................................................................................... 164
7.8 INTEL MATRIX STORAGE MANAGER INSTALLATION ............................................... 171
A
BIOS OPTIONS .................................................................................................... 177
B
DIO INTERFACE................................................................................................. 181
B.1 DIO INTERFACE INTRODUCTION ........................................................................... 182
B.2 DIO CONNECTOR PINOUTS ................................................................................... 182
B.3 ASSEMBLY LANGUAGE SAMPLES ........................................................................... 183
B.3.1 Enable the DIO Input Function..................................................................... 183
B.3.2 Enable the DIO Output Function .................................................................. 183
C
WATCHDOG TIMER .......................................................................................... 185
Page ix
KINO-9453 Mini-ITX Motherboard
D
ADDRESS MAPPING.......................................................................................... 189
D.1 ADDRESS MAP ...................................................................................................... 190
D.2 1ST MB MEMORY ADDRESS MAP ......................................................................... 190
D.3 IRQ MAPPING TABLE ............................................................................................ 191
D.4 DMA CHANNEL ASSIGNMENTS ............................................................................. 191
E
INTEL® MATRIX STORAGE MANAGER ...................................................... 193
E.1 INTRODUCTION ...................................................................................................... 194
E.1.1 Precautions .................................................................................................... 194
E.2 FEATURES AND BENEFITS ...................................................................................... 195
E.3 ACCESSING THE INTEL® MATRIX STORAGE MANAGER .......................................... 195
E.4 RAID CONFIGURATION ......................................................................................... 196
E.4.1 Creating a RAID Volume ............................................................................... 196
E.4.2 Deleting a RAID Volume................................................................................ 201
E.4.3 Resetting a Disk to Non-RAID....................................................................... 203
E.4.4 Exiting the Matrix Storage Manager............................................................. 206
INDEX............................................................................................................................ 207
Page x
List of Figures
Figure 1-1: KINO-9453 Overview ...................................................................................................3
Figure 2-1: KINO-9453 Dimensions (mm).....................................................................................8
Figure 2-2: External Interface Panel Dimensions (mm) ..............................................................9
Figure 2-3: Data Flow Block Diagram .........................................................................................10
Figure 2-4: 240-pin DIMM Sockets ..............................................................................................13
Figure 4-1: Connector and Jumper Locations...........................................................................30
Figure 4-2: Fan Connector Locations.........................................................................................33
Figure 4-3: Front Panel Connector Location .............................................................................34
Figure 4-4: GPIO Connector Location ........................................................................................35
Figure 4-5: IDE Device Connector Location ..............................................................................36
Figure 4-6: LCD Backlight Connector Location ........................................................................38
Figure 4-7: LVDS LCD Connector Location ...............................................................................39
Figure 4-8: Mini PCI Slot Location ..............................................................................................40
Figure 4-9: Power Connector Location ......................................................................................42
Figure 4-10: 14-Pin Serial Port Connector Locations ...............................................................43
Figure 4-11: 10-Pin Serial Port Connector Locations ...............................................................44
Figure 4-12: SATA Drive Connector Locations ..........................................................................45
Figure 4-13: SPDIF Connector Locations ..................................................................................46
Figure 4-14: Internal USB Connector Locations .......................................................................47
Figure 4-15: KINO-9453 External Interface Connectors............................................................48
Figure 4-16: Audio Connectors ...................................................................................................48
Figure 4-17: VGA Connector........................................................................................................49
Figure 4-18 DVI-I Connector Pinout Locations..........................................................................50
Figure 4-19: RJ-45 Ethernet Connector......................................................................................51
Figure 4-20: PS/2 Pinouts ............................................................................................................52
Figure 4-21: External Serial Port Connector..............................................................................53
Figure 5-1: Make sure the CPU socket retention screw is unlocked ......................................60
Figure 5-2: Lock the CPU Socket Retention Screw...................................................................61
Figure 5-3: IEI CF-479B-RS Cooling Kit......................................................................................62
Figure 5-4: Cooling Kit Support Bracket ....................................................................................63
Figure 5-5: Connect the cooling fan cable.................................................................................63
Page xi
KINO-9453 Mini-ITX Motherboard
Figure 5-6: Installing a DIMM .......................................................................................................64
Figure 5-7: Jumper Locations .....................................................................................................65
Figure 5-8: Clear CMOS Jumper .................................................................................................67
Figure 5-9: COM 3 Function Select Jumper Location...............................................................68
Figure 5-10: LVDS Voltage Selection Jumper Pinout Locations..............................................69
Figure 5-11: IDE Cable Connection.............................................................................................72
Figure 5-12: Dual RS-232 Cable Installation ..............................................................................73
Figure 5-13: SATA Drive Cable Connection ...............................................................................74
Figure 5-14: SATA Power Drive Connection ..............................................................................74
Figure 5-15: Audio Connectors ...................................................................................................76
Figure 5-16: RJ-45 Ethernet Connector......................................................................................77
Figure 5-17: USB Connector........................................................................................................78
Figure 5-18: VGA Connector........................................................................................................79
Figure 5-19: Serial Device Connector.........................................................................................80
Figure 5-20: PS/2 Keyboard/Mouse Connector .........................................................................81
Figure 6-1: Video Function Configuration............................................................................... 134
Figure 7-1: Available Drivers .................................................................................................... 143
Figure 7-2: Chipset Driver Installation Program..................................................................... 144
Figure 7-3: Chipset Driver Installation Welcome Screen....................................................... 145
Figure 7-4: Chipset Driver Installation License Agreement .................................................. 146
Figure 7-5: Chipset Driver Readme File Information ............................................................. 147
Figure 7-6: Chipset Driver Installation Complete ................................................................... 148
Figure 7-7: Select the Operating System ................................................................................ 149
Figure 7-8: VGA Driver .............................................................................................................. 150
Figure 7-9: GMA Driver Readme File ....................................................................................... 151
Figure 7-10: GMA Driver File Extraction.................................................................................. 151
Figure 7-11: GMA Driver Installation Welcome Screen.......................................................... 152
Figure 7-12: GMA Driver License Agreement ......................................................................... 153
Figure 7-13: GMA Driver Installing Notice............................................................................... 153
Figure 7-14: GMA Driver Installation Complete ...................................................................... 154
Figure 7-15: Access Windows Control Panel ......................................................................... 155
Figure 7-16: Double Click the System Icon............................................................................. 156
Figure 7-17: Double Click the Device Manager Tab ............................................................... 156
Figure 7-18: Device Manager List ............................................................................................ 157
Figure 7-19: Search for Suitable Driver ................................................................................... 158
Page xii
Figure 7-20: Locate Driver Files ............................................................................................... 159
Figure 7-21: Location Browsing Window ................................................................................ 159
Figure 7-22: 4-AUDIO\AC-KIT883HD\Windows Folder ........................................................... 160
Figure 7-23: HD Audio Driver Setup Extracting Files............................................................. 161
Figure 7-24: HD Audio Driver Setup Welcome Screen........................................................... 162
Figure 7-25: HD Audio Driver Installation Complete .............................................................. 163
Figure 7-26: CD 4-AUDIO\AC-KIT08R\Windows Folder ......................................................... 165
Figure 7-27: AC`97 Audio Driver Install Shield Wizard Starting............................................ 165
Figure 7-28: AC`97 Audio Driver Setup Preparation .............................................................. 166
Figure 7-29: AC`97 Audio Driver Welcome Screen................................................................. 166
Figure 7-30: AC`97 Audio Driver Software Configuration ..................................................... 167
Figure 7-31: AC`97 Audio Driver Digital Signal....................................................................... 168
Figure 7-32: AC`97 Audio Driver Installation Begins ............................................................. 169
Figure 7-33: AC`97 Audio Driver Installation Complete ......................................................... 170
Figure 7-34: SATA RAID Driver Installation Program ............................................................. 171
Figure 7-35: SATA RAID Setup Program Icon ......................................................................... 172
Figure 7-36: InstallShield Wizard Setup Screen ..................................................................... 172
Figure 7-37: Matrix Storage Manager Setup Screen .............................................................. 173
Figure 7-38: Matrix Storage Manager Welcome Screen ........................................................ 173
Figure 7-39: Matrix Storage Manager Warning Screen .......................................................... 174
Figure 7-40: Matrix Storage Manager License Agreement .................................................... 174
Figure 7-41: Matrix Storage Manager Readme File ................................................................ 175
Figure 7-42: Matrix Storage Manager Setup Complete.......................................................... 176
Page xiii
KINO-9453 Mini-ITX Motherboard
List of Tables
Table 1-1: Technical Specifications ..............................................................................................6
Table 2-1: Processor Features ....................................................................................................11
Table 2-2: Supported Processors ...............................................................................................12
Table 2-3: Supported HDD Specifications..................................................................................16
Table 2-4: Power Consumption ...................................................................................................22
Table 3-1: Package List Contents................................................................................................26
Table 3-2: Optional Items .............................................................................................................27
Table 4-1: Peripheral Interface Connectors ...............................................................................31
Table 4-2: Rear Panel Connectors ..............................................................................................32
Table 4-3: Fan Connector Pinouts...............................................................................................33
Table 4-4: Front Panel Connector Pinouts .................................................................................34
Table 4-5: GPIO Connector Pinouts ............................................................................................35
Table 4-6: IDE Connector Pinouts ...............................................................................................37
Table 4-7: LCD Backlight Connector Pinouts ............................................................................38
Table 4-8: LVDS LCD Connector Pinouts ...................................................................................39
Table 4-9: Mini PCI Slot Pinouts ..................................................................................................41
Table 4-10: Power Connector Pinouts ........................................................................................42
Table 4-11: COM2 Pinouts............................................................................................................43
Table 4-12: COM4 Pinouts............................................................................................................44
Table 4-13: SATA Drive Connector Pinouts................................................................................45
Table 4-14: SPDIF Pinouts ...........................................................................................................46
Table 4-15: USB3 and USB4 Pinouts ..........................................................................................47
Table 4-16: VGA Connector Pinouts ...........................................................................................49
Table 4-17: DVI-I Connector Pinouts...........................................................................................50
Table 4-18: LAN1 and LAN2 Pinouts...........................................................................................51
Table 4-19: RJ-45 Ethernet Connector LEDs .............................................................................51
Table 4-20: PS/2 Connector Pinouts ...........................................................................................52
Table 4-21: External Serial Port Pinouts.....................................................................................53
Table 4-22: External USB Connector Pinouts ............................................................................54
Table 5-1: Jumpers .......................................................................................................................65
Page xiv
Table 5-2: Clear CMOS Jumper Settings ....................................................................................66
Table 5-3: COM 3 Function Select Jumper Settings .................................................................68
Table 5-4: LVDS Voltage Selection Jumper Settings.................................................................69
Table 5-5: IEI Provided Cables ....................................................................................................71
Table 6-1: BIOS Navigation Keys ................................................................................................85
Page xv
KINO-9453 Mini-ITX Motherboard
BIOS Menus
Menu 1: Main .................................................................................................................................86
Menu 2: Advanced ........................................................................................................................88
Menu 3: CPU Configuration.........................................................................................................89
Menu 4: IDE Configuration ..........................................................................................................90
Menu 5: IDE Master and IDE Slave Configuration.....................................................................92
Menu 6: Super IO Configuration .................................................................................................97
Menu 7: Hardware Health Configuration ................................................................................. 100
Menu 8: ACPI Configuration ..................................................................................................... 105
Menu 9: General ACPI Configuration [Advanced\ ACPI Configuration] .............................. 106
Menu 10:Advanced Power Management Configuration ........................................................ 107
Menu 11: Remote Access Configuration [Advanced] .............................................................110
Menu 12: USB Configuration.....................................................................................................114
Menu 13: USB Mass Storage Device Configuration ................................................................116
Menu 14: PCI/PnP Configuration ..............................................................................................119
Menu 15: Boot ............................................................................................................................ 124
Menu 16: Boot Settings Configuration .................................................................................... 125
Menu 17: Boot Device Priority Settings .................................................................................. 128
Menu 18: Removable Drives..................................................................................................... 129
Menu 19: Security ...................................................................................................................... 130
Menu 20: Chipset ....................................................................................................................... 131
Menu 21:NorthBridge Chipset Configuration ......................................................................... 132
Menu 22:SouthBridge Chipset Configuration......................................................................... 136
Menu 23:Exit............................................................................................................................... 138
Page xvi
Glossary
AC ’97
Audio Codec 97
ACPI
Advanced Configuration and
HDD
Hard Disk Drive
Power Interface
IDE
Integrated Data Electronics
APM
Advanced Power Management
I/O
Input/Output
ARMD
ATAPI Removable Media Device
ICH4
I/O Controller Hub 4
ASKIR
Shift Keyed Infrared
L1 Cache Level 1 Cache
ATA
Advanced Technology
L2 Cache Level 2 Cache
Attachments
LCD
Liquid Crystal Display
BIOS
Basic Input/Output System
LPT
Parallel Port Connector
CFII
Compact Flash Type 2
LVDS
Low Voltage Differential Signaling
CMOS
Complementary Metal Oxide
MAC
Media Access Controller
Semiconductor
OS
Operating System
CPU
Central Processing Unit
PCI
Peripheral Connect Interface
Codec
Compressor/Decompressor
PIO
Programmed Input Output
COM
Serial Port
PnP
Plug and Play
DAC
Digital to Analog Converter
POST
Power On Self Test
DDR
Double Data Rate
RAM
Random Access Memory
DIMM
Dual Inline Memory Module
SATA
Serial ATA
DIO
Digital Input/Output
S.M.A.R.T Self Monitoring Analysis and
DMA
Direct Memory Access
EIDE
Enhanced IDE
SPD
Serial Presence Detect
EIST
Enhanced Intel SpeedStep
S/PDI
Sony/Philips Digital Interface
Technology
SDRAM
Synchronous Dynamic Random
Reporting Technology
Access Memory
FDD
Floppy Disk Drive
FDC
Floppy Disk Connector
SIR
Serial Infrared
FFIO
Flexible File Input/Output
UART
Universal Asynchronous
FIFO
First In/First Out
FSB
Front Side Bus
USB
Universal Serial Bus
IrDA
Infrared Data Association
VGA
Video Graphics Adapter
Receiver-transmitter
Page xvii
KINO-9453 Mini-ITX Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page xix
KINO-9453 Mini-ITX Motherboard
Chapter
1
1 Introduction
Page 1
KINO-9453 Mini-ITX Motherboard
1.1 Introduction
The KINO-9453 Mini-ITX form factor motherboard is a Socket 479 Intel® Core 2 Duo, Core
Duo, Core Solo or Celeron M CPU platform. The KINO-9453 has a maximum front side
bus (FSB) frequency of 667MHz and comes with a VGA interface and dual PCI Express
(PCIe) Gigabit Ethernet (GbE). The KINO-9453 supports up to two, second-generation
serial ATA (SATA) hard disk drives (HDD) with maximum transfer rates of 3Gb/s and up to
eight USB 2.0 devices. The KINO-9453 also has a PCI socket and a Mini PCI Express
(PCIe) socket for system expansion. Multiple display support adds versatility to the system
enabling system integrators and designers increased flexibility in selecting display panel
options.
1.1.1 KINO-9453 Benefits
Some of the KINO-9453 benefits are listed below:
Multiple display output options
Storage flexibility with support for SATA II drives and IDE drives
Expandable system with PCI and mini PCI slots
DDR2 support enables faster data transfers
Multiple I/O interfaces provide connectivity to a broad range of external
peripheral devices
1.1.2 KINO-9453 Features
Some of the KINO-9453 features are listed below.
Support for Socket 479 Intel® Core 2 Duo or Core Solo CPUs
Maximum FSB of 667MHz
Supports two 240-pin 400MHz, 533MHz or 667MHz 2GB DDR2 DIMM
memory modules
Two SATA II drives with transfer rates of 3.0Gb/s supported
Two Ultra ATA 100, Ultra ATA 66 or Ultra ATA 33 IDE HDDs supported
Eight USB 2.0 devices supported
Dual PCIe GbE Ethernet connectivity
Multiple display options including CRT, DVI and dual-channel LVDS
Page 2
KINO-9453 Mini-ITX Motherboard
Mini-ITX form factor
RoHS compliant
Supports AT and ATX power supplies
1.2 KINO-9453 Overview
1.2.1 KINO-9453 Overview Photo
The KINO-9453 has a wide variety of internal and external peripheral connectors. The
peripheral connectors are connected to devices including PCI devices, mini PCI devices,
storage devices, display devices and serial communications devices. A labeled photo of
the peripheral connectors on the front of the KINO-9453 is shown in Figure 1-1.
Figure 1-1: KINO-9453 Overview
Page 3
KINO-9453 Mini-ITX Motherboard
1.2.2 KINO-9453 Peripheral Connectors and Jumpers
The KINO-9453 has the following connectors on-board:
2 x DDR2 DIMM sockets
1 x Digital I/O connector
2 x Fan connectors
1 x Front panel connector
1 x IDE Interface connector
1 x LCD backlight connector
1 x LVDS LCD connector
1 x Mini PCI slot
1 x PCI slot
1 x Power connector
2 x Serial port connectors
2 x SATA II connectors
1 x SPDIF connector
2 x USB connectors
The KINO-9453 has the following external peripheral interface connectors on the board
rear panel
2 x Audio jacks
1 x VGA connector
2 x Ethernet connectors
2 x Keyboard/Mouse connectors
2 x Serial port connectors
1 x DVI connector
4 x USB 2.0 ports
The KINO-9453 has the following on-board jumpers:
Clear CMOS
COM3 mode selection (RS-232/422/485)
LVDS LCD voltage selection
Page 4
KINO-9453 Mini-ITX Motherboard
1.2.3 Technical Specifications
KINO-9453 technical specifications are listed in Table 1-1. See Chapter 2 for details.
Specification
KINO-9453
Form Factor
Mini-ITX
Socket 479 Intel® Core™ 2 Duo Mobile
System CPU
Socket 479 Intel® Core™ Duo
Socket 479 Intel® Core™ Solo
Front Side Bus
667MHz
Northbridge: Intel® 945GM
System Chipset
Southbridge: Intel® ICH7M
Two 240-pin DIMM sockets support two 400MHz, 533MHz or
Memory
667MHz DDR2 DIMM with a maximum capacity of 4GB
CRT: Integrated in the Intel® 945GM to support CRT
Display
DVI: Integrated in the Intel® 945GM by SDVO interface
LVDS: Dual channel 18-bit LVDS LCD panel
BIOS
AMI BIOS
Audio
Realtek ALC655 with AC’97 codec
LAN
Two Broadcom BCM5787M PCIe GbE controllers
Three RS-232 serial ports (one internal, two external)
COM
One RS-232, RS-422 or RS-485 serial port
USB2.0
Eight USB 2.0 devices supported
IDE
One 40-pin IDE connects to two Ultra ATA33/66/100 devices
SATA
Two 3.0Gb/s SATA drives supported
Page 5
KINO-9453 Mini-ITX Motherboard
Specification
KINO-9453
Two PS/2 connectors support mouse and keyboard
Keyboard/mouse
connectivity
Watchdog Timer
Software programmable 1-255 sec. by super I/O
Power Supply
AT and ATX supported
Temperature
0ºC – 60ºC (32ºF - 140ºF)
Humidity (operating)
5%~95% non-condensing
Dimensions (LxW)
170mm x 170mm
Weight (GW/NW)
900g/ 362g
Table 1-1: Technical Specifications
Page 6
KINO-9453 Mini-ITX Motherboard
Chapter
2
2 Detailed Specifications
Page 7
KINO-9453 Mini-ITX Motherboard
2.1 Overview
This chapter describes the specifications and on-board features of the KINO-9453 in
detail.
2.2 Dimensions
2.2.1 Board Dimensions
The dimensions of the board are listed below:
Length:
170mm
Width:
170mm
Figure 2-1: KINO-9453 Dimensions (mm)
Page 8
KINO-9453 Mini-ITX Motherboard
2.2.2 External Interface Panel Dimensions
External peripheral interface connector panel dimensions are shown in Figure 2-2.
Figure 2-2: External Interface Panel Dimensions (mm)
2.3 Data Flow
Figure 2-3 shows the data flow between the two on-board chipsets and other components
installed on the motherboard and described in the following sections of this chapter.
Page 9
KINO-9453 Mini-ITX Motherboard
Figure 2-3: Data Flow Block Diagram
Page 10
KINO-9453 Mini-ITX Motherboard
2.4 Compatible Processors
2.4.1 Compatible Processor Overview
The KINO-9453 supports the following socket 479 processors:
®
Intel
®
Intel
®
Intel
Core™2 Duo Mobile processors
Core™ Duo processors
Core™ Solo processors
All three of the above processors communicate with the Intel
®
945GM northbridge chipset
through a 667MHz front side bus (FSB). Features of the supported processors are listed in
Table 2-1.
CPU Features
Core™2 Duo Mobile
Core™ Duo
Core™ Solo
Dual core
Yes
Yes
No
Enhanced Halt State (C1E)
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
EM64T
Yes
No
No
Virtualization Technology
Yes
Yes
No
Enhanced Intel
®
®
Speedstep
Technolgy
Execute Disable Bit
®
Intel
®
Intel
Table 2-1: Processor Features
2.4.2 Supported Processors
Specifications for the compatible processors are listed in Table 2-2 below:
Family
sSpec# CPU Speed Processor # Bus Speed
Mfg Tech
Stepping
Cache Size
Core™2 Duo Mobile
SL9SJ
2.33 GHz
T7600
667 MHz
65 nm
B2
4 MB
SL9SK
2.16 GHz
T7400
667 MHz
65 nm
B2
4 MB
SL9SL
2 GHz
T7200
667 MHz
65 nm
B2
4 MB
SL9SP
1.83 GHz
T5600
667 MHz
65 nm
B2
2 MB
SL9SQ
1.66 GHz
T5500
667 MHz
65 nm
B2
2 MB
Page 11
KINO-9453 Mini-ITX Motherboard
Family
sSpec# CPU Speed Processor # Bus Speed
Mfg Tech
Stepping
Cache Size
Core™ Duo
SL8VT
2 GHz
T2500
667 MHz
65 nm
C0
2 MB
SL9DN
1.66 GHz
T2300E
667 MHz
65 nm
C0
2 MB
SL92X
1.83 GHz
T1400
667 MHz
65 nm
C0
2 MB
Core™ Solo
Table 2-2: Supported Processors
2.5 Intel® 945GM Northbridge Chipset
2.5.1 Intel® 945GM Overview
The Intel® 945GM northbridge chipset has the Generation 3.1 Intel Integrated Graphics
Engine and the Intel® Graphics Media Accelerator 950 (Intel® GMA 950). The integrated
graphics and memory controller hub (GMCH) facilitates the flow of information primarily
between the following four interfaces:
Front Side Bus (FSB)
System Memory Interface
Graphics Interface
Direct Media Interface (DMI)
2.5.2 Intel® 945GM Memory Support
WARNING:
Only DDR2 memory module can be installed on the KINO-9453. Do not
install DDR memory modules. If a DDR memory module is installed on
the KINO-9453, the KINO-9453 may be irreparably damaged.
The Intel® 945GM northbridge chipset on the NANO-945GM supports two DDR2 240-pin
DIMMs with the following features:
Two 240-pin DIMMs
Page 12
KINO-9453 Mini-ITX Motherboard
DDR2 only (DO NOT install a DDR DIMM)
Single-channel or dual-channel
Capacities of 256MB, 512MB, 1GB or 2GB
Transfer speeds of 400MHz, 533MHz, or 667MHz
The memory sockets are shown in Figure 2-4.
Figure 2-4: 240-pin DIMM Sockets
2.5.3 Intel® 945GM Integrated Graphics
The Intel® 945GM northbridge chipset has an Intel® Gen. 3.5 integrated graphics engine
that supports the following display devices:
Analog CRT
LVDS
S-DVO interface (DVI connector)
2.5.3.1 Intel® 945GM Analog CRT Support
A DB-15 VGA connector on the external peripheral interface connector panel is interfaced
to the Intel® 945GM graphics engine. The Intel® 945GM internal graphics engine, with an
integrated 400MHz RAMDAC and hot plug CRT support, supports analog CRT monitors
up to QXGA.
Page 13
KINO-9453 Mini-ITX Motherboard
2.5.3.2 Intel® 945GM LVDS Support
A 30-pin LVDS crimp connector is interfaced to the Intel® 945GM graphics engine. The
Intel® 945GM internal graphics engine supports LVDS displays with the following features:
Up to UXGA monitors with a maximum resolution of 1600 x 1200
18-bit 25MHz to 112MHz single-channel or dual-channel LVDS screens
CPIS 1.5 compliant LVDS screens
2.5.3.3 Intel® 945GM SDVO Support
The Intel® 945GM internal graphics engine has the following SDVO output features:
Concurrent operation of PCIe x 1 with SDVO
Two SDVO ports supported
o
o
o
o
SDVO is muxed onto the PCIe pins
DVI 1.0 support for external digital monitor
Only Downstream HDCP support
Display hot plug support
2.5.4 Intel® 945GM Direct Media Interface (DMI)
Intel® 945GM northbridge GMCH is connected to the Intel® ICH7M Southbridge Chipset
through the chip-to-chip Direct Media Interface (DMI). Features of the Intel® 945GM DMI
are listed below:
2GB/s (1GB/s in each direction) bus speed
32-bit downstream address
2.6 Intel® ICH7M Southbridge Chipset
2.6.1 Intel® ICH7M Overview
The Intel® ICH7M southbridge chipset is connected to the Intel® 945GM northbridge
GMCH through the chip-to-chip Direct Media Interface (DMI). Some of the features of the
Intel® ICH7M are listed below.
Complies with PCI Express Base Specification, Revision 1.0a
Page 14
KINO-9453 Mini-ITX Motherboard
Complies with PCI Local Bus Specification, Revision 2.3 and supports 33MHz
PCI operations
Supports ACPI Power Management Logic
Contains:
o
o
o
Enhanced DMA controller
Interrupt controller
Timer functions
Integrated SATA host controller with DMA operations interfaced to two SATA
connectors on the KINO-9453
Integrated IDE controller supports Ultra ATA 100/66/33
Supports the six USB 2.0 devices on the KINO-9453 with four UHCI
controllers and one EHCI controller
Complies with System Management Bus (SMBus) Specification, Version 2.0
Supports Audio Codec ’97 (AC’97) Revision 2.3
Supports Intel® High Definition Audio
Contains Low Pin Count (LPC) interface
Supports Firmware Hub (FWH) interface
2.6.2 Intel® ICH7M Audio Codec ’97 Controller
The WAFER-8522 has an integrated REALTEK ALC655 CODEC. The ALC655 CODEC is
a 16-bit, full-duplex AC'97 Rev. 2.3 compatible six-channel audio CODEC designed for PC
multimedia systems, including host/soft audio and AMR/CNR-based designs. Complete
surround sound requires six-channel audio consisting of:
Front left
Front right
Back left
Back right
Center
Subwoofer
Page 15
KINO-9453 Mini-ITX Motherboard
2.6.3 Intel® ICH7M IDE Interface
The integrated IDE interface on the ICH7M southbridge supports two IDE hard disks and
ATAPI devices. PIO IDE transfers up to 16MB/s and Ultra ATA transfers of 100MB/s. The
integrated IDE interface is able to support the following IDE HDDs:
Ultra ATA/100, with data transfer rates up to 100MB/s
Ultra ATA/66, with data transfer rates up to 66MB/s
Ultra ATA/33, with data transfer rates up to 33MB/s
Specification
Ultra ATA/100
Ultra ATA/66
Ultra ATA/100
IDE devices
2
2
2
PIO Mode
0–4
0–4
0–4
PIO Max Transfer Rate
16.6 MB/s
16.6 MB/s
16.6 MB/s
DMA/UDMA designation
UDMA 3 - 4
UDMA 3 – 4
UDMA 2
DMA/UDMA Max Transfer
100MB/s
66MB/s
33MB/s
Controller Interface
5V
5V
5V
Table 2-3: Supported HDD Specifications
2.6.4 Intel® ICH7M Low Pin Count (LPC) Interface
The ICH7M LPC interface complies with the LPC 1.1 specifications. The LPC bus from the
ICH6 is connected to the following components:
BIOS chipset
Super I/O chipset
2.6.5 Intel® ICH7M PCI Interface
The PCI interface on the ICH7M is compliant with the PCI Revision 2.3 implementation.
Some of the features of the PCI interface are listed below.
PCI Revision 2.3 compliant
Page 16
KINO-9453 Mini-ITX Motherboard
33MHz
5V tolerant PCI signals (except PME#)
Integrated PCI arbiter supports up to seven PCI bus masters
2.6.6 Intel® ICH7M Real Time Clock
256 bytes of battery backed RAM is provided by the Motorola MC146818A real time clock
(RTC) integrated into the ICH6. The RTC operates on a 3V battery and 32.768KHz crystal.
The RTC keeps track of the time and stores system data even when the system is turned
off.
2.6.7 Intel® ICH7M SATA Controller
The integrated SATA controller on the ICH7M southbridge supports two SATA drives on
the KINO-9453 with independent DMA operations. SATA controller specifications are listed
below.
Supports two SATA drives
Supports 3Gb/s data transfer speeds
Supports Serial ATA Specification, Revision 1.0a
2.6.8 Intel® ICH7M USB Controller
Up to eight high-speed, full-speed or low-speed USB devices are supported by the ICH7M
on the KINO-9453. High-speed USB 2.0, with data transfers of up to 480MB/s, is enabled
with the ICH7M integrated Enhanced Host Controller Interface (EHCI) compliant host
controller. USB full-speed and low-speed signaling is supported by the ICH7M integrated
Universal Host Controller Interface (UHCI) controllers.
2.7 PCIe Bus Components
2.7.1 PCIe Bus Overview
The PCIe bus is connected to components listed below:
Two PCIe GbE Broadcom LAN chipsets
Page 17
KINO-9453 Mini-ITX Motherboard
2.7.2 Broadcom PCI Express GbE interface
The BCM5787M Broadcom PCI Express (PCIe) GbE controller is a 10/100/1000BASE-T
Ethernet LAN controller. The BCM5787M combines a triple-speed IEEE 802.3 compliant
Media Access Controller (MAC) with a triple-speed Ethernet transceiver, a PCIe bus
interface, and an on-chip buffer memory. Some of the BCM5787 controller features are
listed below:
Integrated 10/100/1000BASE-T transceiver
Automatic MDI crossover function
PCIe v1.0a
10/100/1000BASE-T full/half-duplex MAC
Wake on LAN support meeting the ACPI requirements
Statistics for SNMP MIB II, Ethernet-like MIB, and Ethernet MIB (802.3z,
clause 30)
Serial EEPROM or serial flash support
JTAG support
2.8 LPC Bus Components
2.8.1 LPC Bus Overview
The LPC bus is connected to components listed below:
BIOS chipset
Super I/O chipset
2.8.2 BIOS Chipset
The BIOS chipset has a licensed copy of AMI BIOS installed on the chipset. Some of the
BIOS features are listed below:
AMI Flash BIOS
SMIBIOS (DMI) compliant
Console redirection function support
PXE (Pre-boot Execution Environment) support
USB booting support
Page 18
KINO-9453 Mini-ITX Motherboard
2.8.3 Super I/O chipset
The iTE IT8712F Super I/O chipset is connected to the ICH6 southbridge through the LPC
bus. The iTE IT8712F is an LPC interface-based Super I/O device that comes with
Environment Controller integration. Some of the features of the iTE IT8712F chipset are
listed below:
LPC Interface
PC98/99/2001, ACPI and LANDesk Compliant
Enhanced Hardware Monitor
Fan Speed Controller
SmartGuardian Controller
Single +5V Power Supply
Two 16C550 UARTs for serial port control
One IEEE 1284 Parallel Port
Floppy Disk Controller
Keyboard Controller
Watchdog Timer
Serial IRQ Support
Vbat & Vcch Support
Single +5V Power Supply
Some of the Super I/O features are described in more detail below:
2.8.3.1 Super I/O LPC Interface
The LPC interface on the Super I/O complies with the Intel® Low Pin Count Specification
Rev. 1.0. The LPC interface supports both LDRQ# and SERIRQ protocols as well as PCI
PME# interfaces.
2.8.3.2 Super I/O 16C550 UARTs
The onboard Super I/O has two integrated 16C550 UARTs that can support the following:
Two standard serial ports (COM1 and COM2)
IrDa 1.0 and ASKIR protocols
Page 19
KINO-9453 Mini-ITX Motherboard
Another two chipsets connected to the LPC bus provided connectivity to another two serial
port connectors (COM3 and COM4).
2.8.3.3 Super I/O Enhanced Hardware Monitor
The Super I/O Enhanced Hardware Monitor monitors three thermal inputs, VBAT internally,
and eight voltage monitor inputs. These hardware parameters are reported in the BIOS
and can be read from the BIOS Hardware Health Configuration menu.
2.8.3.4 Super I/O Fan Speed Controller
The Super I/O fan speed controller enables the system to monitor the speed of the fan.
One of the pins on the fan connector is reserved for fan speed detection and interfaced to
the fan speed controller on the Super I/O. The fan speed is then reported in the BIOS.
2.8.3.5 Super I/O Keyboard Controller
The Super I/O keyboard controller can execute the 8042 instruction set. Some of the
keyboard controller features are listed below:
The 8042 instruction is compatible with a PS/2 keyboard and PS/2 mouse
Gate A20 and Keyboard reset output
Supports multiple keyboard power on events
Supports mouse double-click and/or mouse move power on events
2.9 Environmental and Power Specifications
2.9.1 System Monitoring
Three thermal inputs on the KINO-9453 Super I/O Enhanced Hardware Monitor monitor
the following temperatures:
System temperature
Power temperature
CPU temperature
Page 20
KINO-9453 Mini-ITX Motherboard
Eight voltage inputs on the KINO-9453 Super I/O Enhanced Hardware Monitor monitor the
following voltages:
CPU Core
+2.5V
+3.30V
+5.00V
+12.0V
GMCH (1.5V)
1.05V
5VSB
VBAT
The KINO-9453 Super I/O Enhanced Hardware Monitor also monitors the following
voltages internally:
VBAT
The KINO-9453 Super I/O Enhanced Hardware Monitor also monitors the following fan
speeds:
CPU Fan speed
The values for the above environmental parameters are all recorded in the BIOS
Hardware Health Configuration menu.
2.9.2 Operating Temperature and Temperature Control
The maximum and minimum operating temperatures for the KINO-9453 are listed below.
Minimum Operating Temperature: 0ºC (32°F)
Maximum Operating Temperature: 60°C (140°F)
A cooling fan and heat sink must be installed on the CPU. Thermal paste must be
smeared on the lower side of the heat sink before it is mounted on the CPU. Heat sinks
are also mounted on the northbridge and southbridge chipsets to ensure the operating
temperature of these chips remain low.
Page 21
KINO-9453 Mini-ITX Motherboard
2.9.3 Power Consumption
Table 2-4 shows the power consumption parameters for the KINO-9453 running with a
2.16GHz Intel® Pentium® M processor with 1GB of 667MHz DDR2 memory.
Voltage
Current
+5V
4.86A
+12V
1.75A
Table 2-4: Power Consumption
Page 22
KINO-9453 Mini-ITX Motherboard
Chapter
3
3 Unpacking
Page 23
KINO-9453 Mini-ITX Motherboard
3.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
KINO-9453 may result in permanent damage to the KINO-9453 and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the KINO-9453. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the KINO-9453, or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the KINO-9453, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
KINO-9453.
Only handle the edges of the PCB: When handling the PCB, hold the PCB
by the edges.
3.2 Unpacking
3.2.1 Unpacking Precautions
When the KINO-9453 is unpacked, please do the following:
Follow the anti-static precautions outlined in Section 3.1.
Make sure the packing box is facing upwards so the KINO-9453 does not fall
out of the box.
Make sure all the components shown in Section 3.3 are present.
Page 24
KINO-9453 Mini-ITX Motherboard
3.3 Unpacking Checklist
NOTE:
If some of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the KINO-9453 from or contact an IEI sales
representative directly. To contact an IEI sales representative, please
send an email to [email protected]
3.3.1 Package Contents
The KINO-9453 is shipped with the following components:
Quantity
Item and Part Number
1
KINO-9453
1
Dual RS-232 Cable
Image
(P/N:32200-028401-RS)
1
IDE cable
(P/N: 32200-008800-RS)
2
SATA cables
(P/N: 32000-0628000-RS)
Page 25
KINO-9453 Mini-ITX Motherboard
1
SATA power cable
(P/N: 32100-088600-RS)
1
Mini jumper Pack
1
Quick Installation Guide
1
Utility CD
1
I/O Shielding
Table 3-1: Package List Contents
3.3.2 Optional Items
NOTE:
The items listed in this section are optional items that must be ordered
separately. Please contact your KINO-9453 vendor, distributor or
reseller for more information or, contact iEi directly by sending an email
to [email protected]
The following optional items are available for the KINO-9453.
Page 26
KINO-9453 Mini-ITX Motherboard
Quantity
Item and Part Number
1
Dual port USB cable
Image
(P/N: CB-USB02-RS)
1
Four port USB cable
(P/N: CB-USB14-RS)
1
RS-232/422/485 cable
(P/N: 32200-000077-RS)
1
CPU Cooler
(P/N: CF-479B-RS)
Table 3-2: Optional Items
Page 27
KINO-9453 Mini-ITX Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 28
KINO-9453 Mini-ITX Motherboard
Chapter
4
4 Connector Pinouts
Page 29
KINO-9453 Mini-ITX Motherboard
4.1 Peripheral Interface Connectors
Section 4.1.1 shows peripheral interface connector locations. Section 4.1.2 lists all the
peripheral interface connectors seen in Section 4.1.3.
4.1.1 KINO-9453 Layout
Figure 4-1 shows the on-board peripheral connectors, rear panel peripheral connectors
and on-board jumpers.
Figure 4-1: Connector and Jumper Locations
Page 30
KINO-9453 Mini-ITX Motherboard
4.1.2 Peripheral Interface Connectors
Table 4-1 shows a list of the peripheral interface connectors on the KINO-9453. Detailed
descriptions of these connectors can be found in Section 4.2.
Connector
Type
Label
ATX power supply connector
20-pin ATX connector
PWR1
Digital I/O connector
10-pin header
DIO1
Fan connector (CPU)
3-pin wafer
CPU_FAN1
Fan connector (Northbridge)
3-pin wafer
NB_FAN1
Front panel connector
14-pin header
F_PANEL1
IDE Interface connector
40-pin box header
IDE1
LVDS connector
30-pin crimp
LVDS1
LCD backlight connector
6-pin wafer connector
CN1
PCI slot
124-pin slot
PCI2
Mini PCI Card slot
124-pin slot
MINIPCI
Serial ATA (SATA) connector
7-pin SATA connector
SATA1
Serial ATA (SATA) connector
7-pin SATA connector
SATA2
Serial port connector (COM 3)
14-pin header
COM3
Serial port connector (COM 4)
10-pin header
COM4
SPDIF connector
5-pin header
SPDIF1
USB connector
8-pin header
USB4
USB connector
8-pin header
USB5
Table 4-1: Peripheral Interface Connectors
Page 31
KINO-9453 Mini-ITX Motherboard
4.1.3 External Interface Panel Connectors
Table 4-2 lists the rear panel connectors on the KINO-9453. Detailed descriptions of these
connectors can be found in Section 4.3.
Connector
Type
Label
Audio connector
Audio jack
AUDIO
Ethernet connector
RJ-45
LAN/USB1
Ethernet connector
RJ-45
LAN/USB2
Keyboard and mouse connector
PS/2 connector
KBMS1
RS-232 serial port connector
Male DB-9
COM1
RS-232 serial port connector
Male DB-9
COM2
USB ports
USB port
LAN/USB1
USB ports
USB port
LAN/USB2
VGA port connector
Female DB-15
VIDEO
DVI connector
DVI connector
VIDEO
Table 4-2: Rear Panel Connectors
4.2 Internal Peripheral Connectors
Internal peripheral connectors are found on the motherboard and are only accessible
when the motherboard is outside of the chassis. This section has complete descriptions of
all the internal, peripheral connectors on the KINO-9453.
4.2.1 Fan Connectors
CN Label:
CPU_FAN1 and NB_FAN1
CN Type:
3-pin header
Page 32
KINO-9453 Mini-ITX Motherboard
CN Location:
See Figure 4-2
CN Pinouts:
See Table 4-3
The cooling fan connectors on the KINO-9453 provide a 12V, 500mA current to one CPU
cooling fan and one Northbridge cooling fan. There is a “sense” pin in the fan connector,
which transfers the fan’s sense signal to the system BIOS in order to recognize the fan
speed. Please note that only some specific types of fans offer a rotation signal.
Figure 4-2: Fan Connector Locations
PIN NO.
DESCRIPTION
1
GND
2
+12V
3
Sense
Table 4-3: Fan Connector Pinouts
4.2.2 Front Panel Connector
CN Label:
F_PANEL1
CN Type:
14-pin header (2x7)
CN Location:
See Figure 4-3
CN Pinouts:
See Table 4-4
Page 33
KINO-9453 Mini-ITX Motherboard
The front panel connector connects to several external switches and indicators to monitor
and control the motherboard. These indicators and switches include:
Power
Power button
Reset button
Speaker
HDD
Figure 4-3: Front Panel Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
Power LED+
2
Speaker+
3
NC
4
NC
5
Power LED-
6
NC
7
Power Button#
8
Speaker-
9
Power Button
10
NC
11
IDE LED+
12
Reset Button
13
IDE LED-
14
Reset Button#
Table 4-4: Front Panel Connector Pinouts
4.2.3 Digital Input/Output Connector
CN Label:
DIO1
CN Type:
10-pin header (2x6)
Page 34
KINO-9453 Mini-ITX Motherboard
CN Location:
See Figure 4-4
CN Pinouts:
See Table 4-5
The DIO connector is managed through a Super I/O chip. The DIO connector pins are
user programmable. The digital IO port of KINO-9453 is 5V CMOS level.
Figure 4-4: GPIO Connector Location
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
GND
2
+5V
3
INPUT0
4
OUTPUT0
5
INPUT1
6
OUTPUT1
7
INPUT2
8
OUTPUT2
9
INPUT3
10
OUTPUT3
Table 4-5: GPIO Connector Pinouts
4.2.4 IDE Connector
CN Label:
IDE1
CN Type:
40-pin header (2x20)
CN Location:
See Figure 4-5
CN Pinouts:
See Table 4-6
Page 35
KINO-9453 Mini-ITX Motherboard
One primary 40-pin IDE device connector on the KINO-9453 motherboard supports
connectivity to ATA 100 IDE devices with data transfer rates up to 100MB/s.
Figure 4-5: IDE Device Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
RESET#
2
GND
3
DATA 7
4
DATA 8
5
DATA 6
6
DATA 9
7
DATA 5
8
DATA 10
9
DATA 4
10
DATA 11
11
DATA 3
12
DATA 12
Page 36
KINO-9453 Mini-ITX Motherboard
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
13
DATA 2
14
DATA 13
15
DATA 1
16
DATA 14
17
DATA 0
18
DATA 15
19
GND
20
(KEY)
21
DRQ
22
GND
23
IOW#
24
GND
25
IOR#
26
GND
27
CHRDY
28
GND
29
DACK
30
GND
31
INTERRUPT
32
N/C
33
SA1
34
P66DET
35
SA0
36
SA2
37
HDC CS0#
38
HDC CS1#
39
HDD ACTIVE#
40
GND
Table 4-6: IDE Connector Pinouts
4.2.5 LCD Backlight Connector
CN Label:
CN1
CN Type:
6-pin header (1x6)
CN Location:
See Figure 4-6
CN Pinouts:
See Table 4-7
The LCD backlight connector is for the LCD inverter connection.
Page 37
KINO-9453 Mini-ITX Motherboard
Figure 4-6: LCD Backlight Connector Location
PIN NO.
DESCRIPTION
1
Back Light Power
2
Back Light Power
3
Back Light enable
4
NC
5
GND
6
GND
Table 4-7: LCD Backlight Connector Pinouts
4.2.6 LVDS LCD connector
CN Label:
LVDS1
CN Type:
30-pin connector (2x15)
CN Location:
See Figure 4-7
CN Pinouts:
See Table 4-8
The connector supports one or two channel (18 or 36bit) LVDS panel.
Page 38
KINO-9453 Mini-ITX Motherboard
Figure 4-7: LVDS LCD Connector Location
PIN NO.
1
DESCRIPTION
GND
st
PIN NO.
DESCRIPTION
2
GND
3
1 LVDS data0 output +
4
1st LVDS data0 output -
5
1st LVDS data1 output +
6
1st LVDS data1 output -
7
1st LVDS data2 output +
8
1st LVDS data2 output -
9
1st LVDS clock output +
10
1st LVDS clock output -
11
NC
12
NC
13
GND
14
GND
15
2nd LVDS data0 output +
16
2nd LVDS data0 output -
17
2nd LVDS data1 output +
18
2nd LVDS data1 output -
19
2nd LVDS data2 output +
20
2nd LVDS data2 output -
21
2nd LVDS clock output +
22
2nd LVDS clock output -
23
NC
24
NC
25
GND
26
GND
27
+LCD (3.3V, 5V or 12V)
28
+LCD (3.3V, 5V or 12V)
29
+LCD (3.3V, 5V or 12V)
30
+LCD (3.3V, 5V or 12V)
Table 4-8: LVDS LCD Connector Pinouts
Page 39
KINO-9453 Mini-ITX Motherboard
4.2.7 Mini PCI Slot
CN Label:
MINIPCI
CN Type:
124-pin Mini PCI Type III slot
CN Location:
See Figure 4-8
CN Pinouts:
See Table 4-9
Mini PCI is a small form factor version of a PCI card. Mini PCI expansion devices can be
inserted into the Mini PCI slot.
Figure 4-8: Mini PCI Slot Location
PIN
NAME
PIN
NAME
PIN
NAME
PIN
NAME
1
TIP
32
GROUND
63
3.3V
94
AD[02]
2
RING
33
AD[31]
64
FRAME#
95
AD[03]
3
8PMJ-3
34
PME#
65
CLKRUN#
96
AD[00]
4
8PMJ-1
35
AD[29]
66
TRDY#
97
5V
5
8PMJ-6
36
RESERVED
67
SERR#
98
RESERVED_WIP5
6
8PMJ-2
37
GROUND
68
STOP#
99
AD[01]
7
8PMJ-7
38
AD[30]
69
GROUND
100
RESERVED_WIP5
8
8PMJ-4
39
AD[27]
70
3.3V
101
GROUND
9
8PMJ-8
40
3.3V
71
PERR#
102
GROUND
10
8PMJ-5
41
AD[25]
72
DEVSEL#
103
AC_SYNC
Page 40
KINO-9453 Mini-ITX Motherboard
11
LED1_GRNP
42
AD[28]
73
C/BE[1]#
104
M66EN
12
LED2_YELP
43
RESERVED
74
GROUND
105
AC_SDATA_IN
13
LED1_GRNN
44
AD[26]
75
AD[14]
106
AC_SDATA_OUT
14
LED2_YELN
45
C/BE[3]#
76
AD[15]
107
AC_BIT_CLK
15
CHSGND
46
AD[24]
77
GROUND
108
AC_CODEC_ID0#
16
RESERVED
47
AD[23]
78
AD[13]
109
AC_CODEC_ID1#
17
INTB#
48
IDSEL
79
AD[12]
110
AC_RESET#
18
5V
49
GROUND
80
AD[11]
111
MOD_AUDIO_MON
19
3.3V
50
GROUND
81
AD[10]
112
RESERVED
20
INTA#
51
AD[21]
82
GROUND
113
AUDIO_GND
21
RESERVED
52
AD[22]
83
GROUND
114
GROUND
22
RESERVED
53
AD[19]
84
AD[09]
115
SYS_AUDIO_OUT
23
GROUND
54
AD[20]
85
AD[08]
116
SYS_AUDIO_IN
24
3.3VAUX
55
GROUND
86
C/BE[0]#
117
SYS_AUDIO_OUT GND
25
CLK
56
PAR
87
AD[07]
118
SYS_AUDIO_IN GND
26
RST#
57
AD[17]
88
3.3V
119
AUDIO_GND
27
GROUND
58
AD[18]
89
3.3V
120
AUDIO_GND
28
3.3V
59
C/BE[2]#
90
AD[06]
121
RESERVED
29
REQ#
60
AD[16]
91
AD[05]
122
MPCIACT#
30
GNT#
61
IRDY#
92
AD[04]
123
VCC5VA
31
3.3V
62
Ground
93
RESERVED
124
3.3VAUX
Table 4-9: Mini PCI Slot Pinouts
4.2.8 Power Connector
CN Label:
PWR1
CN Type:
20-pin connector
CN Location:
See Figure 4-9
CN Pinouts:
See Table 4-10
This 20-pin power connector supports the ATX power supply.
Page 41
KINO-9453 Mini-ITX Motherboard
Figure 4-9: Power Connector Location
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
3.3V
11
3.3V
2
3.3V
12
-12V
3
GND
13
GND
4
+5V
14
PS_ON
5
GND
15
GND
6
+5V
16
GND
7
GND
17
GND
8
Power good
18
-5V
9
5VSB
19
+5V
10
+12V
20
+5V
Table 4-10: Power Connector Pinouts
4.2.9 14-Pin Serial Port Connectors
CN Label:
COM3
CN Type:
14-pin header (2x7)
CN Location:
See Figure 4-10
CN Pinouts:
See Table 4-11
Page 42
KINO-9453 Mini-ITX Motherboard
The serial ports connectors connect to RS-232/422/485 serial port device.
Figure 4-10: 14-Pin Serial Port Connector Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTS
7
DTR
8
RI
9
GND
10
NC
11
TX+
12
TX-
13
RX+
14
RX-
Table 4-11: COM2 Pinouts
4.2.10 10-Pin Serial Port Connectors
CN Label:
COM4
CN Type:
10-pin header (2x5)
CN Location:
See Figure 4-11
CN Pinouts:
See Table 4-12
The serial ports connectors connect to RS-232 serial port device.
Page 43
KINO-9453 Mini-ITX Motherboard
Figure 4-11: 10-Pin Serial Port Connector Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTS
7
DTR
8
RI
9
GND
10
NC
Table 4-12: COM4 Pinouts
4.2.11 SATA Drive Connectors
CN Label:
SATA1 and SATA2
CN Type:
1x7 pin SATA drive connector
CN Location:
See Figure 4-12
CN Pinouts:
See Table 4-13
The two SATA drive connectors are connected to four SATA II drives. SATA II drives
transfer data at speeds as high as 3.0Gb/s.
Page 44
KINO-9453 Mini-ITX Motherboard
Figure 4-12: SATA Drive Connector Locations
PIN NO.
DESCRIPTION
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
Table 4-13: SATA Drive Connector Pinouts
4.2.12 SPDIF Connector
CN Label:
SPDIF1
CN Type:
5-pin header (1x5)
CN Location:
See Figure 4-13
CN Pinouts:
See Table 4-14
The SPDIF connector connects to the S/PDIF audio module, which bears S/PDIF digital
output. S/PDIF (Sony/Philips Digital Interface) is a newest audio transfer file format, which
Page 45
KINO-9453 Mini-ITX Motherboard
allows the user to enjoy digital audio. The SPDIF1 port provides digital audio to external
speaker or compressed AC3 data to an external Dolby Digital Decoder via a coaxial cable.
Figure 4-13: SPDIF Connector Locations
PIN NO.
DESCRIPTION
1
+5V
2
(KEY)
3
SPDIF_OUT
4
GND
5
SPDIF_IN
Table 4-14: SPDIF Pinouts
4.2.13 Internal USB Connectors
CN Label:
USB4 and USB5
CN Type:
8-pin header (2x4)
CN Location:
See Figure 4-14
CN Pinouts:
See Table 4-15
One 2x4 pin connector provides connectivity to two USB 2.0 ports. The USB ports are
used for I/O bus expansion.
Page 46
KINO-9453 Mini-ITX Motherboard
Figure 4-14: Internal USB Connector Locations
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
VCC
2
GND
3
DATA0-
4
DATA1+
5
DATA0+
6
DATA1-
7
GND
8
VCC
Table 4-15: USB3 and USB4 Pinouts
4.3 External Interface Connectors
The peripheral connectors on the back panel are connected to devices externally when
the KINO-9453 is installed in a chassis. The peripheral connectors on the rear panel are:
2 x Audio jacks
1 x VGA connector
2 x RJ-45 Ethernet connectors
2 x Keyboard/mouse connectors
2 x Serial port connectors
1 x DVI connector
4 x USB 2.0 connectors
Page 47
KINO-9453 Mini-ITX Motherboard
Figure 4-15: KINO-9453 External Interface Connectors
4.3.1 Audio Connectors
CN Label:
AUDIO
CN Type:
Audio jack
CN Location:
See Figure 4-15
CN Pinouts:
See Figure 4-16
Line Out port (Lime): Connects a headphone or a speaker. In 4,6,8-channel
configuration, the function of this port becomes Front Speaker Out.
Microphone (Pink): Connects a microphone.
Figure 4-16: Audio Connectors
4.3.2 CRT Connector
CN Label:
VIDEO
CN Type:
15-pin female connector
CN Location:
See Figure 4-15
Page 48
KINO-9453 Mini-ITX Motherboard
CN Pinouts:
See Table 4-16
The standard 15-pin VGA connector connects to a CRT or LCD display monitor.
Figure 4-17: VGA Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
RED
2
GREEN
3
BLUE
4
N/C
5
GND
6
GND
7
GND
8
GND
9
VCC
10
GND
11
N/C
12
DDC DAT
13
HSYNC
14
VSYNC
15
DDC CLK
Table 4-16: VGA Connector Pinouts
4.3.3 DVI Connector
CN Label:
VIDEO
CN Type:
DVI interface with analog RGB signal
CN Location:
See Figure 4-15
CN Pinouts:
See Figure 4-18 and Table 4-17
The KINO-9453 has an external DVI connector.
Page 49
KINO-9453 Mini-ITX Motherboard
Figure 4-18 DVI-I Connector Pinout Locations
PIN
Description
PIN
Description
PIN
Description
1
DTX2-
9
DTX1-
17
DTX0-
2
DTX2+
10
DTX1+
18
DTX0+
3
GND
11
GND
19
GND
4
N/C
12
N/C
20
N/C
5
N/C
13
N/C
21
N/C
6
SB_CK_C
14
PVDD1
22
GND
6
SB_DA_C
15
GND
23
DTXC+
8
V_SYNC
16
GND
24
DTXC-
C1
R
C3
B
25
GND
C5
GND
C6
GND
26
GND
C2
G
C4
H_SYNC
Table 4-17: DVI-I Connector Pinouts
4.3.4 Ethernet Connectors
CN Label:
LAN/USB1 and LAN/USB2
CN Type:
RJ-45
CN Location:
See Figure 4-15
CN Pinouts:
See Table 4-18
The KINO-9453 is equipped with two built-in GbE Ethernet controllers. The controllers can
connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the
connector indicating the status of LAN. The pin assignments are listed in the following
table:
Page 50
KINO-9453 Mini-ITX Motherboard
PIN
DESCRIPTION
PIN
DESCRIPTION
1
MDX0+
5
MDX2-
2
MDX0-
6
MDX1-
3
MDX1+
7
MDX3+
4
MDX2+
8
MDX3-
Table 4-18: LAN1 and LAN2 Pinouts
Figure 4-19: RJ-45 Ethernet Connector
The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green
LED indicates activity on the port and the yellow LED indicates the port is linked. See
Table 4-19.
SPEED LED
STATUS
DESCRIPTION
ACT/LINK LED
STATUS
DESCRIPTION
OFF
10Mbps connection
OFF
No link
ORANGE
100Mbps connection
YELLOW
Linked
GREEN
1Gbps connection
BLINKING
Data Activity
Table 4-19: RJ-45 Ethernet Connector LEDs
4.3.5 Keyboard/Mouse Connector
CN Label:
KBMS1
CN Type:
PS/2 connector
CN Location:
See Figure 4-15
CN Pinouts:
See Table 4-20 and Figure 4-20
Page 51
KINO-9453 Mini-ITX Motherboard
The KINO-9453 keyboard and mouse connectors are standard PS/2 connectors.
Figure 4-20: PS/2 Pinouts
PIN
DESCRIPTION
PIN
DESCRIPTION
1
L_KDAT
7
L_MDAT
2
NC
8
NC
3
GND
9
GND
4
5V
10
5V
5
L_KCLK
11
L_MCLK
6
NC
12
NC
Table 4-20: PS/2 Connector Pinouts
4.3.6 Serial Port Connectors
CN Label:
COM1/2
CN Type:
DB-9
CN Location:
See Figure 4-15
CN Pinouts:
See Table 4-21 and Figure 4-21
The serial ports can be connected to a serial communications device directly.
Page 52
KINO-9453 Mini-ITX Motherboard
Figure 4-21: External Serial Port Connector
PIN
Description
1
DATA CARRIER DETECT (DCD)
2
RECEIVE DATA (RXD)
3
TRANSMIT DATA (TXD)
4
DATA TERMINAL READY (DTR)
5
GROUND (GND)
6
DATA SET READY (DSR)
7
REQUEST TO SEND (RTS)
8
CLEAR TO SEND (CTS)
9
RING INDICATOR (RI)
Table 4-21: External Serial Port Pinouts
4.3.7 USB Connector
CN Label:
LAN/USB1 and LAN/USB2
CN Type:
USB port
CN Location:
See Figure 4-15
CN Pinouts:
See Table 4-22
USB devices can be connected directly to the USB connectors on the rear panel.
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
VCC
5
VCC
2
USBD0-
6
USBD1-
Page 53
KINO-9453 Mini-ITX Motherboard
3
USBD0+
7
USBD1+
4
GND
8
GND
Table 4-22: External USB Connector Pinouts
Page 54
KINO-9453 Mini-ITX Motherboard
Chapter
5
5 Installation
Page 55
KINO-9453 Mini-ITX Motherboard
5.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
KINO-9453 may result in permanent damage to the KINO-9453 and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the KINO-9453. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the KINO-9453, or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the KINO-9453, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
KINO-9453.
Only handle the edges of the PCB: When handling the PCB, hold the PCB
by the edges.
Page 56
KINO-9453 Mini-ITX Motherboard
5.2 Installation Considerations
NOTE:
The following installation notices and installation considerations should
be read and understood before the KINO-9453 is installed. All
installation notices pertaining to the installation of the KINO-9453
should be strictly adhered to. Failing to adhere to these precautions
may lead to severe damage of the KINO-9453 and injury to the person
installing the motherboard.
5.2.1 Installation Notices
WARNING:
The installation instructions described in this manual should be
carefully followed in order to prevent damage to the KINO-9453,
KINO-9453 components and injury to the user.
Before and during the installation please DO the following:
Read the user manual:
o
The user manual provides a complete description of the KINO-9453
installation instructions and configuration options.
Wear an electrostatic discharge cuff (ESD):
o
Electronic components are easily damaged by ESD. Wearing an ESD cuff
removes ESD from the body and helps prevent ESD damage.
Place the KINO-9453 on an antistatic pad:
o
When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.
Turn all power to the KINO-9453 off:
Page 57
KINO-9453 Mini-ITX Motherboard
o
When working with the KINO-9453, make sure that it is disconnected from
all power supplies and that no electricity is being fed into the system.
Before and during the installation of the KINO-9453 DO NOT:
Remove any of the stickers on the PCB board. These stickers are required for
warranty validation.
Use the product before verifying all the cables and power connectors are
properly connected.
Allow screws to come in contact with the PCB circuit, connector pins, or its
components.
5.2.2 Installation Checklist
The following checklist is provided to ensure the KINO-9453 is properly installed.
All the items in the packing list are present
The CPU is installed
The CPU cooling kit is properly installed
A compatible memory module is properly inserted into the slot
The CF Type I or CF Type II card is properly installed into the CF socket
The jumpers have been properly configured
The KINO-9453 is inserted into a chassis with adequate ventilation
The correct power supply is being used
The following devices are properly connected
o
o
o
o
o
o
o
o
IDE device
SATA drives
Keyboard and mouse cable
Audio kit
Power supply
USB cable
Serial port cable
Parallel port cable
The following external peripheral devices are properly connected to the
chassis:
o
Page 58
VGA screen
KINO-9453 Mini-ITX Motherboard
o
o
o
Keyboard
Mouse
RS-232 serial communications device
5.3 CPU, CPU Cooling Kit and DIMM Installation
WARNING:
A CPU should never be turned on without the specified cooling kit
being installed. If the cooling kit (heat sink and fan) is not properly
installed and the system turned on, permanent damage to the CPU,
KINO-9453 and other electronic components attached to the system
may be incurred. Running a CPU without a cooling kit may also result
in injury to the user.
The CPU, CPU cooling kit and DIMM are the most critical components of the KINO-9453.
If one of these component is not installed the KINO-9453 cannot run.
5.3.1 Socket 479 CPU Installation
WARNING:
CPUs are expensive and sensitive components. When installing the
CPU please be careful not to damage it in anyway. Make sure the CPU
is installed properly and ensure the correct cooling kit is properly
installed.
To install a socket 479 CPU onto the KINO-9453, follow the steps below:
Page 59
KINO-9453 Mini-ITX Motherboard
WARNING:
When handling the CPU, only hold it on the sides. DO NOT touch the
pins at the bottom of the CPU.
Step 1: Unlock the CPU retention screw. When shipped, the retention screw of the
CPU socket should be in the unlocked position. If it is not in the unlocked
position, use a screwdriver to unlock the screw. See Figure 5-1.
Figure 5-1: Make sure the CPU socket retention screw is unlocked
Step 2: Inspect the CPU socket. Make sure there are no bent pins and make sure the
socket contacts are free of foreign material. If any debris is found, remove it with
compressed air.
Step 3: Correctly Orientate the CPU. Make sure the IHS (integrated heat sink) side is
facing upwards.
Step 4: Correctly position the CPU. Match the Pin 1 mark with the cut edge on the
CPU socket. See Figure 5-1.
Page 60
KINO-9453 Mini-ITX Motherboard
Step 5: Align the CPU pins. Carefully align the CPU pins with the holes in the CPU
socket.
Step 6: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are
properly aligned, the CPU should slide into the CPU socket smoothly.
Step 7: Lock the retention screw. Rotate the retention screw into the locked position.
See Figure 5-2.Step 0:
Figure 5-2: Lock the CPU Socket Retention Screw
Page 61
KINO-9453 Mini-ITX Motherboard
5.3.2 Cooling Kit CF-479B-RS Installation
Figure 5-3: IEI CF-479B-RS Cooling Kit
An IEI Socket 479 CPU cooling kit can be purchased separately. The cooling kit comprises
a CPU heat sink and a cooling fan.
WARNING:
Do not wipe off (accidentally or otherwise) the pre-sprayed layer of
thermal paste on the bottom of the CF-479B-RS heat sink. The thermal
paste between the CPU and the heat sink is important for optimum
heat dissipation.
To install the CF-479B-RS cooling kit, please follow the steps below.
Step 1: Place the cooling kit onto the CPU. Make sure the CPU cooling fan cable
can be properly routed when the cooling kit is installed.
Step 2: Properly align the cooling kit. Make sure its four spring screw fasteners can
pass through the pre-drilled holes on the PCB.
Step 3: Secure the cooling kit. From the solder side of the PCB, align the support
bracket to the screw threads on heat sink that were inserted through the PCB
holes. (See Figure 5-4)
Page 62
KINO-9453 Mini-ITX Motherboard
Figure 5-4: Cooling Kit Support Bracket
Step 4: Tighten the screws. Use a screwdriver to tighten the four screws. Tighten each
nut a few turns at a time and do not over-tighten the screws.
Step 5: Connect the fan cable. Connect the cooling kit fan cable to the fan connector
on the motherboard. Carefully route the cable and avoid heat generating chips
and fan blades. See Figure 5-5. Step 0:
Figure 5-5: Connect the cooling fan cable
Page 63
KINO-9453 Mini-ITX Motherboard
5.3.3 DIMM Installation
WARNING:
Only DDR2 memory module can be installed on the KINO-9453. Do not
install DDR memory modules. If a DDR memory module is installed on
the KINO-9453, the KINO-9453 may be irreparably damaged. Please
make sure the purchased DIMM complies with the memory
specifications of the KINO-9453. DIMM specifications compliant with
the KINO-9453 are listed in Chapter 2.
To install a DIMM into a DIMM socket, please follow the steps below and refer to
Figure 5-6.
Figure 5-6: Installing a DIMM
Step 1: Open the DIMM socket handles. The DIMM socket has two handles that
secure the DIMM into the socket. Before the DIMM can be inserted into the
socket, the handles must be opened. See Figure 5-6.
Page 64
KINO-9453 Mini-ITX Motherboard
Step 2: Align the DIMM with the socket. The DIMM must be oriented in such a way
that the notch in the middle of the DIMM must be aligned with the plastic bridge
in the socket. See Figure 5-6.
Step 3: Insert the DIMM. Once properly aligned, the DIMM can be inserted into the
socket. As the DIMM is inserted, the white handles on the side of the socket will
close automatically and secure the DIMM to the socket. See Figure 5-6.
Step 4: Removing a DIMM. To remove a DIMM, push both handles outward. The
memory module is ejected by a mechanism in the socket.Step 0:
5.4 Jumper Settings
NOTE:
A jumper is a metal bridge used to close an
electrical circuit. It consists of two or three metal
pins and a small metal clip (often protected by a
plastic cover) that slides over the pins to connect
them. To CLOSE/SHORT a jumper means
connecting the pins of the jumper with the plastic
clip and to OPEN a jumper means removing the
Figure 5-7: Jumper Locations
plastic clip from a jumper.
Before the KINO-9453 is installed in the system, the jumpers must be set in accordance
with the desired configuration. The jumpers on the KINO-9453 are listed in Table 5-1.
Description
Label
Type
Clear CMOS
JP3
3-pin header
COM3 mode selection
JP1
3-pin header
LVDS LCD voltage selection
JP4
4-pin header
Table 5-1: Jumpers
Page 65
KINO-9453 Mini-ITX Motherboard
5.4.1 Clear CMOS Jumper
Jumper Label:
JP3
Jumper Type:
3-pin header
Jumper Settings:
See Table 5-2
Jumper Location:
See Figure 5-8
If the KINO-9453 fails to boot due to improper BIOS settings, the clear CMOS jumper
clears the CMOS data and resets the system BIOS information. To do this, use the jumper
cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1
and 2.
If the “CMOS Settings Wrong” message is displayed during the boot up process, the fault
may be corrected by pressing the F1 to enter the CMOS Setup menu. Do one of the
following:
Enter the correct CMOS setting
Load Optimal Defaults
Load Failsafe Defaults.
After having done one of the above, save the changes and exit the CMOS Setup menu.
The clear CMOS jumper settings are shown in Table 5-2.
Clear CMOS
Description
Short 1 - 2
Keep CMOS Setup
Short 2 - 3
Clear CMOS Setup
Default
Table 5-2: Clear CMOS Jumper Settings
The location of the clear CMOS jumper is shown in Figure 5-8 below.
Page 66
KINO-9453 Mini-ITX Motherboard
Figure 5-8: Clear CMOS Jumper
5.4.2 COM 3 Function Select Jumper
Jumper Label:
JP1
Jumper Type:
3-pin header
Jumper Settings:
See Table 5-3
Jumper Location:
See Figure 5-9
The COM 3 Function Select jumper sets the communication protocol used by the second
serial communications port (COM 3) as RS-232, RS-422 or RS-485. The COM 3 Function
Select settings are shown in Figure 5-9.
Page 67
KINO-9453 Mini-ITX Motherboard
COM 3 Function Select
Description
Short 1-2
RS-232
Short 2-3
RS-422 or RS-485
Default
Table 5-3: COM 3 Function Select Jumper Settings
The COM 3 Function Select jumper location is shown in Table 5-3.
Figure 5-9: COM 3 Function Select Jumper Location
5.4.3 LVDS Voltage Selection
WARNING:
Permanent damage to the screen and KINO-9453 may occur if the
wrong voltage is selected with this jumper. Please refer to the user
guide that cam with the monitor to select the correct voltage.
Jumper Label:
JP4
Jumper Type:
4-pin header
Jumper Settings:
See Table 5-4
Jumper Location:
See Figure 5-10
Page 68
KINO-9453 Mini-ITX Motherboard
The LVDS Voltage Selection jumper allows the LVDS screen voltage to be set. The LVDS
Voltage Selection jumper settings are shown in Table 5-4.
LVDS Voltage Select
Description
Short 1-2
+3V
Short 3-4
+5V
Default
Table 5-4: LVDS Voltage Selection Jumper Settings
The LVDS Voltage Selection jumper location. is shown in Figure 5-10.
Figure 5-10: LVDS Voltage Selection Jumper Pinout Locations
Page 69
KINO-9453 Mini-ITX Motherboard
5.5 Chassis Installation
5.5.1 Airflow
WARNING:
Airflow is critical to the cooling of the CPU and other onboard
components. The chassis in which the KINO-9453 must have air vents
to allow cool air to move into the system and hot air to move out.
The KINO-9453 must be installed in a chassis with ventilation holes on the sides allowing
airflow to travel through the heat sink surface. In a system with an individual power supply
unit, the cooling fan of a power supply can also help generate airflow through the board
surface.
NOTE:
IEI has a wide range of backplanes available. Please contact your
KINO-9453 vendor, reseller or an IEI sales representative at
[email protected] or visit the IEI website (http://www.ieiworld.com.tw)
to find out more about the available chassis.
5.5.2 Motherboard Installation
To install the KINO-9453 motherboard into the chassis please refer to the reference
material that came with the chassis.
Page 70
KINO-9453 Mini-ITX Motherboard
5.6 Internal Peripheral Device Connections
5.6.1 Peripheral Device Cables
The cables listed in Table 5-5 are shipped with the KINO-9453.
Quantity
Type
1
IDE Cable
1
Dual RS-232 cable
2
SATA drive cables
1
SATA drive power cable
Table 5-5: IEI Provided Cables
Optional cables are listed below:
USB cable (dual port)
USB cable (four port)
RS-232/422/485 cable
5.6.2 IDE Cable Connection
The IDE flat cable connects to the KINO-9453 to one or two IDE devices. To connect an
IDE HDD to the KINO-9453, please follow the instructions below.
Step 1: Locate the IDE connector. The location/s of the IDE device connector/s is/are
shown in Chapter 3.
Step 2: Insert the connector. Connect the IDE cable connector to the onboard
connector. See Figure 5-11. A key on the front of the cable connector ensures it
can only be inserted in one direction.
Page 71
KINO-9453 Mini-ITX Motherboard
Figure 5-11: IDE Cable Connection
Step 3: Connect the cable to an IDE device. Connect the two connectors on the other
side of the cable to one or two IDE devices. Make sure that pin 1 on the cable
corresponds to pin 1 on the connectorStep 0:
5.6.3 Dual RS-232 Cable Connection
The dual RS-232 cable consists of two connectors attached to two independent cables.
Each cable is then attached to a D-sub 9 male connector that is mounted onto a bracket.
To install the dual RS-232 cable, please follow the steps below.
Step 1: Locate the connectors. The locations of the RS-232 connectors are shown in
Chapter 3.
Step 2: Insert the cable connectors. Insert one connector into each serial port box
headers. See Figure 5-12. A key on the front of the cable connectors ensures
the connector can only be installed in one direction.
Page 72
KINO-9453 Mini-ITX Motherboard
Figure 5-12: Dual RS-232 Cable Installation
Step 3: Secure the bracket. The dual RS-232 connector has two D-sub 9 male
connectors secured on a bracket. To secure the bracket to the chassis please
refer to the reference material that came with the chassisStep 0:
5.6.4 SATA Drive Connection
The KINO-9453 is shipped with two SATA drive cables and one SATA drive power cable.
To connect the SATA drives to the connectors, please follow the steps below.
Step 1: Locate the connectors. The locations of the SATA drive connectors are shown
in Chapter 3.
Step 2: Insert the cable connector. Press the clip on the connector at the end of the
SATA cable and insert the cable connector into the onboard SATA drive
connector. See Figure 5-13.
Page 73
KINO-9453 Mini-ITX Motherboard
Figure 5-13: SATA Drive Cable Connection
Step 3: Connect the cable to the SATA disk. Connect the connector on the other end
of the cable to the connector at the back of the SATA drive. See Figure 5-14.
Step 4: Connect the SATA power cable. Connect the SATA power connector to the
back of the SATA drive. See Figure 5-14. Step 0:
Figure 5-14: SATA Power Drive Connection
Page 74
KINO-9453 Mini-ITX Motherboard
5.7 External Peripheral Interface Connection
The following external peripheral devices can be connected to the external peripheral
interface connectors.
Audio devices
RJ-45 Ethernet cable
USB devices
VGA monitors
DVI port devices
Serial port devices
Mouse and keyboard
To install these devices, connect the corresponding cable connector from the actual
device to the corresponding KINO-9453 external peripheral interface connector making
sure the pins are properly aligned.
5.7.1 Audio Connection
Audio signals are interfaced through two phone jack connections. The red phone jack is
for Line Out and green is for MIC In. Follow the steps below to connect audio devices to
the KINO-9453.
Step 1: Locate the audio phone jacks. The location of the audio phone jacks are
shown in Chapter 3.
Step 2: Insert audio phone jack plugs. Insert audio phone jack plugs into the audio
phone jacks on the external peripheral interface. See Figure 5-15. Step 0:
Page 75
KINO-9453 Mini-ITX Motherboard
Figure 5-15: Audio Connectors
5.7.2 RJ-45 Ethernet Connection
The KINO-9453 has two RJ-45 Ethernet connectors on the external peripheral interface
panel for LAN communications. Follow the steps below to connect an RJ-45 Ethernet
connector to the KINO-9453.
Step 1: Locate the RJ-45 connector. The location of the RJ-45 connector is shown in
Chapter 3.
Step 2: Insert an RJ-45 plug. Insert the RJ-45 plug of a LAN into the RJ-45 receptacle
on the external peripheral interface. See Figure 5-16. Step 0:
Page 76
KINO-9453 Mini-ITX Motherboard
Figure 5-16: RJ-45 Ethernet Connector
5.7.3 USB Connection
The external USB Series "A" receptacle connectors provide easier and quicker access to
external USB devices. Follow the steps below to connect USB devices to the KINO-9453.
Step 1: Locate the USB Series "A" receptacle connectors. The location of the USB
Series "A" receptacle connectors are shown in Chapter 3.
Step 2: Insert a USB Series "A" plug. Insert the USB Series "A" plug of a device into
the USB Series "A" receptacle on the external peripheral interface. See Figure
5-17. Step 0:
Page 77
KINO-9453 Mini-ITX Motherboard
Figure 5-17: USB Connector
5.7.4 VGA Monitor Connection
The KINO-9453 has a single female DB-15 connector on the external peripheral interface
panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor
to the KINO-9453, please follow the instructions below.
Step 1: Locate the female DB-15 connector. The location of the female DB-15
connector is shown in Chapter 3.
Step 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen
cable with the female DB-15 connector on the external peripheral interface.
Step 3: Insert the VGA connector. Once the connectors are properly aligned with the
insert the male connector from the VGA screen into the female connector on the
KINO-9453. See Figure 5-18.
Page 78
KINO-9453 Mini-ITX Motherboard
Figure 5-18: VGA Connector
Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA
monitor to the external interface by tightening the two retention screws on either
side of the connector. Step 0:
5.7.5 Serial Device Connection
The KINO-9453 has two female DB-9 connectors on the external peripheral interface
panel for serial devices. Follow the steps below to connect a serial device to the
KINO-9453.
Step 1: Locate the DB-9 connector. The location of the DB-9 connector is shown in
Chapter 3.
Step 2: Insert the serial connector. Insert the DB-9 connector of a serial device into
the DB-9 connector on the external peripheral interface. See Figure 5-19.
Page 79
KINO-9453 Mini-ITX Motherboard
Figure 5-19: Serial Device Connector
Step 3: Secure the connector. Secure the serial device connector to the external
interface by tightening the two retention screws on either side of the connector.
Step 0:
5.7.6 PS/2 Keyboard/Mouse Connection
The KINO-9453 has a dual PS/2 connector on the external peripheral interface panel. The
dual PS/2 connector is used to connect to a keyboard and mouse to the system. Follow
the steps below to connect a keyboard and mouse to the KINO-9453.
Step 1: Locate the dual PS/2 connector. The location of the dual PS/2 connector is
shown in Chapter 3.
Step 2: Insert the keyboard/mouse connector. Insert a PS/2 keyboard or mouse
connector into the appropriate PS/2 connector on the external peripheral
interface connector. See Figure 5-20. Step 0:
Page 80
KINO-9453 Mini-ITX Motherboard
Figure 5-20: PS/2 Keyboard/Mouse Connector
Page 81
KINO-9453 Mini-ITX Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 82
KINO-9453 Mini-ITX Motherboard
Chapter
6
6 AMI BIOS
Page 83
KINO-9453 Mini-ITX Motherboard
6.1 Introduction
A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup
program allows users to modify the basic system configuration. This chapter describes
how to access the BIOS setup program and the configuration options that may be
changed.
6.1.1 Starting Setup
The AMI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DELETE key as soon as the system is turned on or
2. Press the DELETE key when the “Press Del to enter SETUP”
message appears on the screen. 0.
If the message disappears before the DELETE key is pressed, restart the computer and try
again.
6.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press ESC to quit. Navigation
keys are shown in.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
Page Up key
Increase the numeric value or make changes
Page Dn key
Decrease the numeric value or make changes
Page 84
KINO-9453 Mini-ITX Motherboard
Key
Function
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
F2 /F3 key
Change color from total 16 colors. F2 to select color
forward.
F10 key
Save all the CMOS changes, only for Main Menu
Table 6-1: BIOS Navigation Keys
6.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC or
the F1 key again.
6.1.4 Unable to Reboot After Configuration Changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter 5.
6.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
Main Changes the basic system configuration.
Advanced Changes the advanced system settings.
PCIPnP Changes the advanced PCI/PnP Settings
Boot Changes the system boot configuration.
Security Sets User and Supervisor Passwords.
Chipset Changes the chipset settings.
Power Changes power management settings.
Exit Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
Page 85
KINO-9453 Mini-ITX Motherboard
6.2 Main
The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
BIOS Menu 1: Main
System Overview
The System Overview lists a brief summary of different system components. The fields in
System Overview cannot be changed. The items shown in the system overview include:
AMI BIOS: Displays auto-detected BIOS information
o
o
o
Version:
Current BIOS version
Build Date: Date the current BIOS version was made
ID:
Installed BIOS ID
Processor: Displays auto-detected CPU specifications
o
Page 86
Type: Names the currently installed processor
KINO-9453 Mini-ITX Motherboard
o
o
Speed: Lists the processor speed
Count: The number of CPUs on the motherboard
System Memory: Displays the auto-detected system memory.
o
Size:
Lists memory size
The System Overview field also has two user configurable fields:
System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.
6.3 Advanced
Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
WARNING:
Setting the wrong values in the sections below may cause the system
to malfunction. Make sure that the settings made are compatible with
the hardware.
CPU Configuration (see Section 6.3.1)
IDE Configuration (see Section 6.3.2)
SuperIO Configuration (see Section 6.3.3)
Hardware Health Configuration (see Section 6.3.4)
ACPI Configuration (see Section 6.3.5)
APM Configuration (See Section 6.3.6)
Page 87
KINO-9453 Mini-ITX Motherboard
Remote Access Configuration (see Section 6.3.6)
USB Configuration (see Section )
BIOS Menu 2: Advanced
6.3.1 CPU Configuration
Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications
and configure the CPU.
Page 88
KINO-9453 Mini-ITX Motherboard
BIOS Menu 3: CPU Configuration
The CPU Configuration menu (BIOS Menu 3) lists the following CPU details:
Manufacturer: Lists the name of the CPU manufacturer
Brand String: Lists the brand name of the CPU being used
Frequency: Lists the CPU processing speed
FSB Speed: Lists the FSB speed
Cache L1: Lists the CPU L1 cache size
Cache L2: Lists the CPU L2 cache size
6.3.2 IDE Configuration
Use the IDE Configuration menu (BIOS Menu 4) to change and/or set the configuration
of the IDE devices installed in the system.
Page 89
KINO-9453 Mini-ITX Motherboard
BIOS Menu 4: IDE Configuration
ATA/IDE Configuration [Enhanced]
The ATA/IDE Configuration BIOS option allows the user to configure the ATA/IDE device
mode.
Disable all ATA/IDE ports. No Primary/Secondary IDE
Disabled
mode is presented for configuration
Up to 6 HDDs can be used, four for SATA and the other
Compatible
for PATA IDE. If this option is selected, “Legacy IDE
Channels” option is presented for configuration.
Enhanced
DEFAULT
The motherboard allows up to 6 HDDs to use and SATA
drives can be configured into RAID volumes. If this
option is selected, “Configure SATA as” and “Configure
Page 90
KINO-9453 Mini-ITX Motherboard
SATA channels” options are presented for configuration.
Configure SATA as [IDE]
Use the Configure SATA as option to specify how to configure the available SATA
devices.
IDE
DEFAULT
Enables the SATA devices as IDE devices
RAID
Enables the SATA devices as a RAID device
AHCI
Enables Native Command Queuing (NCQ) and SATA hot
plug capability
If AHCI is chosen, enable the stagger Spinup Support and
take all hard disks on board as master
Configure SATA Channels [Before PATA]
Use Configure SATA Channels option to specify how to configure the available SATA
devices.
Behind
The system detects the SATA devices after the IDE
PATA
devices
Before
DEFAULT
PATA
The system detects the SATA devices before the IDE
devices
IDE Master and IDE Slave
When entering setup, BIOS auto detects the presence of IDE devices. BIOS displays the
status of the auto detected IDE devices. The following IDE devices are detected and are
shown in the IDE Configuration menu:
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Page 91
KINO-9453 Mini-ITX Motherboard
Secondary IDE Slave
Third IDE Master
Third IDE Slave
The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the
IDE devices installed in the system. If an IDE device is detected, and one of the above
listed four BIOS configuration options are selected, the IDE configuration options shown in
Section 6.3.2.1 appear.
6.3.2.1 IDE Master, IDE Slave
Use the IDE Master and IDE Slave configuration menu to view both primary and
secondary IDE device details and configure the IDE devices connected to the system.
BIOS Menu 5: IDE Master and IDE Slave Configuration
Type [Auto]
Page 92
KINO-9453 Mini-ITX Motherboard
Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from
after the Power-On Self-Test (POST) is complete.
BIOS is prevented from searching for an IDE disk
Not Installed
drive on the specified channel.
Auto
DEFAULT
The BIOS auto detects the IDE disk drive type
attached to the specified channel. This setting should
be used if an IDE hard disk drive is attached to the
specified channel.
The CD/DVD option specifies that an IDE CD-ROM
CD/DVD
drive is attached to the specified IDE channel. The
BIOS does not attempt to search for other types of
IDE disk drives on the specified channel.
This option specifies an ATAPI Removable Media
ARMD
Device. These include, but are not limited to:
ZIP
LS-120
LBA/Large Mode [Auto]
Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical
Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the
maximum drive capacity is 137 GB.
BIOS is prevented from using the LBA mode control on
Disabled
the specified channel.
Auto
DEFAULT
BIOS auto detects the LBA mode control on the specified
channel.
Page 93
KINO-9453 Mini-ITX Motherboard
Block (Multi-Sector Transfer) [Auto]
Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto detect if the
device supports multi-sector transfers.
BIOS is prevented from using Multi-Sector Transfer on the
Disabled
specified channel. The data to and from the device occurs
one sector at a time.
Auto
DEFAULT
BIOS auto detects Multi-Sector Transfer support on the
drive on the specified channel. If supported the data
transfer to and from the device occurs multiple sectors at
a time.
PIO Mode [Auto]
Use the PIO Mode option to select the IDE PIO (Programmable I/O) mode program timing
cycles between the IDE drive and the programmable IDE controller. As the PIO mode
increases, the cycle time decreases.
Auto
DEFAULT
BIOS auto detects the PIO mode. Use this value if the IDE disk
drive support cannot be determined.
0
PIO mode 0 selected with a maximum transfer rate of 3.3MBps
1
PIO mode 1 selected with a maximum transfer rate of 5.2MBps
2
PIO mode 2 selected with a maximum transfer rate of 8.3MBps
3
PIO mode 3 selected with a maximum transfer rate of 11.1MBps
4
PIO mode 4 selected with a maximum transfer rate of 16.6MBps
(This setting generally works with all hard disk drives
manufactured after 1999. For other disk drives, such as IDE
CD-ROM drives, check the specifications of the drive.)
Page 94
KINO-9453 Mini-ITX Motherboard
DMA Mode [Auto]
Use the DMA Mode BIOS selection to adjust the DMA mode options.
Auto
DEFAULT
BIOS auto detects the DMA mode. Use this value if the IDE
disk drive support cannot be determined.
SWDMA0
Single Word DMA mode 0 selected with a maximum data
transfer rate of 2.1MBps
SWDMA1
Single Word DMA mode 1 selected with a maximum data
transfer rate of 4.2MBps
SWDMA2
Single Word DMA mode 2 selected with a maximum data
transfer rate of 8.3MBps
MWDMA0
Multi Word DMA mode 0 selected with a maximum data
transfer rate of 4.2MBps
MWDMA1
Multi Word DMA mode 1 selected with a maximum data
transfer rate of 13.3MBps
MWDMA2
Multi Word DMA mode 2 selected with a maximum data
transfer rate of 16.6MBps
UDMA1
Ultra DMA mode 0 selected with a maximum data transfer
rate of 16.6MBps
UDMA1
Ultra DMA mode 1 selected with a maximum data transfer
rate of 25MBps
UDMA2
Ultra DMA mode 2 selected with a maximum data transfer
rate of 33.3MBps
UDMA3
Ultra DMA mode 3 selected with a maximum data transfer
rate of 44MBps (To use this mode, it is required that an
80-conductor ATA cable is used.)
Page 95
KINO-9453 Mini-ITX Motherboard
Ultra DMA mode 4 selected with a maximum data transfer
UDMA4
rate of 66.6MBps (To use this mode, it is required that an
80-conductor ATA cable is used.)
Ultra DMA mode 5 selected with a maximum data transfer
UDMA5
rate of 99.9MBps (To use this mode, it is required that an
80-conductor ATA cable is used.)
S.M.A.R.T [Auto]
Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and
Reporting Technology (SMART) on the drive on the specified channel. S.M.A.R.T predicts
impending drive failures. The S.M.A.R.T BIOS option enables or disables this function.
Auto
DEFAULT
BIOS auto detects HDD SMART support.
Disabled
Prevents BIOS from using the HDD SMART feature.
Enabled
Allows BIOS to use the HDD SMART feature
32Bit Data Transfer [Enabled]
Use the 32Bit Data Transfer BIOS option to enables or disable 32-bit data transfers.
Prevents the BIOS from using 32-bit data transfers.
Disabled
Enabled
DEFAULT
Allows BIOS to use 32-bit data transfers on supported
hard disk drives.
6.3.3 Super IO Configuration
Use the Super IO Configuration menu (BIOS Menu 6) to set or change the
configurations for the FDD controllers, parallel ports and serial ports.
Page 96
KINO-9453 Mini-ITX Motherboard
BIOS Menu 6: Super IO Configuration
Serial Port1 Address [3F8/IRQ4]
Use the Serial Port1 Address option to select the Serial Port 1 base address.
No base address is assigned to Serial Port 1
Disabled
3F8/IRQ4
DEFAULT
Serial Port 1 I/O port address is 3F8 and the interrupt
address is IRQ4
3E8/IRQ4
Serial Port 1 I/O port address is 3E8 and the interrupt
address is IRQ4
2E8/IRQ3
Serial Port 1 I/O port address is 2E8 and the interrupt
address is IRQ3
Page 97
KINO-9453 Mini-ITX Motherboard
Serial Port1 Mode [Normal]
Use the Serial Port1 Mode option to select the transmitting and receiving mode for the
first serial port.
Normal
(Default)
Serial Port 1 mode is normal
IrDA
Serial Port 1 mode is IrDA
ASK IR
Serial Port 1 mode is ASK IR
Serial Port2 Address [2F8/IRQ3]
Use the Serial Port2 Address option to select the Serial Port 2 base address.
No base address is assigned to Serial Port 2
Disabled
2F8/IRQ3
DEFAULT
Serial Port 2 I/O port address is 3F8 and the interrupt
address is IRQ3
Serial Port 2 I/O port address is 3E8 and the interrupt
3E8/IRQ4
address is IRQ4
Serial Port 2 I/O port address is 2E8 and the interrupt
2E8/IRQ3
address is IRQ3
Serial Port2 Mode [Normal]
Use the Serial Port2 Mode option to select the Serial Port2 operational mode.
Normal
DEFAULT
Serial Port 2 mode is normal
IrDA
Serial Port 2 mode is IrDA
ASK IR
Serial Port 2 mode is ASK IR
Serial Port3 Address [3E8]
Use the Serial Port3 Address option to select the base addresses for serial port 3
Page 98
KINO-9453 Mini-ITX Motherboard
No base address is assigned to serial port 3
Disabled
3E8
DEFAULT
Serial port 3 I/O port address is 3E8
2E8
Serial port 3 I/O port address is 2E8
2F0
Serial port 3 I/O port address is 2F0
2E0
Serial port 3 I/O port address is 2E0
Serial Port3 IRQ [11]
Use the Serial Port3 IRQ option to select the interrupt address for serial port 3.
Serial port 3 IRQ address is 10
10
11
DEFAULT
Serial port 3 IRQ address is 11
Serial Port4 Address [2E8]
Use the Serial Port4 IRQ option to select the interrupt address for serial port 4.
Disabled
No base address is assigned to serial port 3
3E8
Serial port 4 I/O port address is 3E8
2E8
DEFAULT
Serial port 4 I/O port address is 2E8
2F0
Serial port 3 I/O port address is 2F0
2E0
Serial port 4 I/O port address is 2E0
Serial Port4 IRQ [10]
Use the Serial Port4 IRQ option to select the interrupt address for serial port 4.
10
11
DEFAULT
Serial port 4 IRQ address is 10
Serial port 4 IRQ address is 11
Page 99
KINO-9453 Mini-ITX Motherboard
6.3.4 Hardware Health Configuration
The Hardware Health Configuration menu (BIOS Menu 7) shows the operating
temperature, fan speeds and system voltages.
BIOS Menu 7: Hardware Health Configuration
CPU FAN Mode Setting [Full On Mode]
Use the CPU FAN Mode Setting option to configure the second fan.
Full On Mode
Automatic mode
DEFAULT
Fan is on all the time
Fan is off when the temperature is low
enough. Parameters must be set by the
user.
PWM Manual mode
Page 100
Pulse width modulation set manually
KINO-9453 Mini-ITX Motherboard
When the CPU FAN Mode Setting option is in the Automatic Mode, the following
parameters can be set.
CPU Temp. Limit of OFF
CPU Temp. Limit of Start
CPU Temp. Limit of Full
CPU Fan Start PWM
Slope PWM 1
When the CPU FAN Mode Setting option is in the PWM Manual Mode, the following
parameters can be set.
CPU Fan PWM control
CPU Temp. Limit of OFF [000]
WARNING:
Setting this value too high may cause the fan to stop when the CPU is
at a high temperature and therefore cause the system to be damaged.
The CPU Temp. Limit of OFF option can only be set if the CPU FAN Mode Setting option
is set to Automatic Mode. Use the CPU Temp. Limit of OFF option to select the CPU
temperature at which the cooling fan should automatically turn off. To select a value, select
the CPU Temp. Limit of OFF option and enter a decimal number between 000 and 127.
The temperature range is specified below.
Minimum Value: 0°C
Maximum Value: 127°C
CPU Temp. Limit of Start [020]
Page 101
KINO-9453 Mini-ITX Motherboard
WARNING:
Setting this value too high may cause the fan to start only when the
CPU is at a high temperature and therefore cause the system to be
damaged.
The CPU Temp. Limit of Start option can only be set if the CPU FAN Mode Setting
option is set to Automatic Mode. Use the CPU Temp. Limit of Start option to select the
CPU temperature at which the cooling fan should automatically turn on. When the fan
starts, it rotates using the starting pulse width modulation (PWM) specified in the CPU Fan
Start PWM option below. To select a value, select the CPU Temp. Limit of Start option
and enter a decimal number between 000 and 127. The temperature range is specified
below.
Minimum Value: 0°C
Maximum Value: 127°C
CPU Temp. Limit of Full [080]
WARNING:
Setting this value too high may cause the fan to start rotating at full
speed only when the CPU is at a high temperature and therefore cause
the system to be damaged.
The CPU Temp. Limit of Full option can only be set if the CPU FAN Mode Setting option
is set to Automatic Mode. Use the CPU Temp. Limit of Full option to select the CPU
temperature at which the cooling fan starts to rotate at full speed. When the CPU
temperature exceeds the temperature specified in this option, the fan starts to rotate at full
Page 102
KINO-9453 Mini-ITX Motherboard
speed. To select a value, select the CPU Temp. Limit of Full option and enter a decimal
number between 000 and 127. The temperature range is specified below.
Minimum Value: 0°C
Maximum Value: 127°C
CPU Fan Start PWM [070]
The CPU Fan Start PWM option can only be set if the CPU FAN Mode Setting option is
set to Automatic Mode. Use the CPU Fan Start PWM option to select the PWM mode the
fan starts to rotate with after the temperature specified in the CPU Temp. Limit of Start is
exceeded. The Super I/O chipset supports 128 PWM modes. To select a value, select the
CPU Fan Start PWM option and enter a decimal number between 000 and 127. The
temperature range is specified below.
PWM Minimum Mode: 0
PWM Maximum Mode: 127
Slope PWM 1 [1 PWM]
The Slope PWM 1 option can only be set if the CPU FAN Mode Setting option is set to
Automatic Mode. Use the Slope PWM 1 option to select the linear rate at which the PWM
mode increases with respect to an increase in temperature. A list of available options is
shown below:
0 PWM
1 PWM
2 PWM
4 PWM
8 PWM
16 PWM
32 PWM
64 PWM
Page 103
KINO-9453 Mini-ITX Motherboard
CPU Fan PWM Control [100]
The CPU Fan PWM Control option can only be set if the CPU FAN Mode Setting option
is set to Manual Mode. Use the CPU Fan PWM Control option to select PWM duty cycle
control. The PWM duty cycle specifies the width of the modulated pulse. A high value
ensures a wide pulse and a low value ensures a narrow pulse. To select a value, select
the CPU Fan PWM Control option and enter a decimal number between 000 and 127.
The PWM Duty Cycle control range is specified below.
PWM Minimum Mode: 0
PWM Maximum Mode: 127
Hardware Health Monitoring
Use the Hardware Health Configuration menu (BIOS Menu 7) monitor system
environmental parameters. The following health parameters are monitored.
Temperature monitoring: The following system temperatures are monitored:
o
o
o
CPU Temperature
System Temperature 1
System Temperature 2
Fan Speed Monitoring: The following system fan speeds are monitored:
o
o
CPU FAN Speed
System FAN Speed
Voltage Monitoring: The following system voltages are monitored:
o
o
o
o
o
o
o
o
o
Page 104
CPU Core
+2.5V
+3.30V
+5.00V
+12.0V
GMCH (1.5V)
1.05V
5VSB
VBAT
KINO-9453 Mini-ITX Motherboard
6.3.5 ACPI Configuration
The ACPI Configuration menu (BIOS Menu 8) configures the Advanced Configuration
and Power Interface (ACPI) and Power Management (APM) options.
BIOS Menu 8: ACPI Configuration
6.3.5.1 General ACPI Configuration
Use the General ACPI Configuration menu (BIOS Menu 9) to select the ACPI state
when the system is suspended.
Page 105
KINO-9453 Mini-ITX Motherboard
BIOS Menu 9: General ACPI Configuration [Advanced\ ACPI Configuration]
Suspend Mode [S3 (STR)]
Use the Suspend Mode option to specify the sleep state the system enters when it is not
being used.
The system enters S1(POS) sleep state. The system
S1 (POS)
appears off. The CPU is stopped; RAM is refreshed; the
system is running in a low power mode.
S3 (STR)
DEFAULT
The system enters a S3(STR) sleep state. The CPU has
no power; RAM is in slow refresh; the power supply is in a
reduced power mode.
Auto
The BIOS automatically selects a sleep state for the
system.
Page 106
KINO-9453 Mini-ITX Motherboard
6.3.6 APM Configuration
The APM Configuration menu (BIOS Menu 10) allows the advanced power
management options to be configured.
BIOS Menu 10:Advanced Power Management Configuration
Power Management/APM [Enabled]
Use the Power Management/APM BIOS option to enable access to the advanced power
management features. If this option is disabled, the only other option on the screen is the
Power Button Mode.
Disables the Advanced Power Management (APM)
Disabled
feature
Enabled
DEFAULT
Enables the APM feature
Page 107
KINO-9453 Mini-ITX Motherboard
Power Supply Mode [ATX]
Use the Power Supply Mode BIOS option to to select the power supply that is connected
to the system.
An AT power supply is connected to the system
AT
ATX
DEFAULT
An ATX power supply is connected to the system
Restore on AC Power Loss by IO [Power Off]
Use the Restore on AC Power Loss by IO BIOS option to specify what state the system
returns to if there is a sudden loss of power to the system.
Power Off
DEFAULT
The system remains turned off
Power On
The system turns on
Last State
The system returns to its previous state. If it was on, it
turns itself on. If it was off, it remains off.
Resume on Ring [Disabled]
Use the Resume on Ring BIOS option to enable activity on the RI (ring in) modem line to
rouse the system from a suspend or standby state. That is, the system will be roused by
an incoming call on a modem.
Disabled
DEFAULT
Wake event not generated by an incoming call
Wake event generated by an incoming call
Enabled
Resume on PME# [Disabled]
Use the Resume on PME# BIOS option to enable activity on the PCI PME (power
management event) controller to rouse the system from a suspend or standby state.
Disabled
Page 108
DEFAULT
Wake event not generated by PCI PME controller
KINO-9453 Mini-ITX Motherboard
activity
Wake event generated by PCI PME controller activity
Enabled
Resume On RTC Alarm [Disabled]
Use the Resume On RTC Alarm option to specify the time the system should be roused
from a suspended state.
Disabled
DEFAULT
The real time clock (RTC) cannot generate a wake
event
If selected, the following appears with values that
Enabled
can be selected:
RTC Alarm Date (Days)
System Time
After setting the alarm, the computer turns itself on
from a suspend state when the alarm goes off.
Resume On PCI-Express WAKE# [Enabled]
The Resume On PCI-Express WAKE# BIOS option specifies if the system is roused from
a suspended or standby state when there is activity on the PCI express port.
Wake event not generated by PCI express activity
Disabled
Enabled
DEFAULT
Wake event generated by PCI express activity
6.3.7 Remote Access Configuration
Use the Remote Access Configuration menu (BIOS Menu 11) to configure remote
access parameters. The Remote Access Configuration is an AMIBIOS feature and
allows a remote host running a terminal program to display and configure the BIOS
settings.
Page 109
KINO-9453 Mini-ITX Motherboard
BIOS Menu 11: Remote Access Configuration [Advanced]
Remote Access [Disabled]
Use the Remote Access option to enable or disable access to the remote functionalities
of the system.
Disabled
Enabled
DEFAULT
Remote access is disabled.
Remote access configuration options shown below
appear:
Serial Port Number
Serial Port Mode
Flow Control
Redirection after BIOS POST
Page 110
KINO-9453 Mini-ITX Motherboard
Terminal Type
VT-UTF8 Combo Key Support
Sredir Memory Display Delay
These configuration options are discussed below.
Serial Port Number [COM1]
Use the Serial Port Number option allows to select the serial port used for remote
access.
COM1
DEFAULT
COM2
System is remotely accessed through COM1
System is remotely accessed through COM2
NOTE: Make sure the selected COM port is enabled through the Super I/O configuration
menu.
Base Address, IRQ [3F8h,4]
The Base Address, IRQ option cannot be configured and only shows the interrupt
address of the serial port listed above.
Serial Port Mode [115200 8,n,1]
Use the Serial Port Mode option to select baud rate through which the console redirection
is made. The following configuration options are available
115200 8,n,1 DEFAULT
57600 8,n,1
38400 8,n,1
19200 8,n,1
09600 8,n,1
Page 111
KINO-9453 Mini-ITX Motherboard
NOTE:
Identical baud rate setting musts be set on the host (a management
computer running a terminal software) and the slave
Flow Control [None]
Use the Flow Control option to report the flow control method for the console redirection
application.
None
DEFAULT
No control flow,
Hardware
Hardware is set as the console redirection
Software
Software is set as the console redirection
Redirection After BIOS POST [Always]
Use the Redirection After BIOS POST option to specify when console redirection should
occur.
Disabled
The console is not redirected after POST
Boot Loader
Redirection is active during POST and during Boot
Loader
Always
DEFAULT
Redirection is always active (Some OSes may not
work if set to Always)
Terminal Type [ANSI]
Use the Terminal Type BIOS option to specify the remote terminal type.
ANSI
Page 112
DEFAULT
The target terminal type is ANSI
KINO-9453 Mini-ITX Motherboard
VT100
The target terminal type is VT100
VT-UTF8
The target terminal type is VT-UTF8
VT-UTF8 Combo Key Support [Disabled]
Use the VT-UFT8 Combo Key Support option to enable additional keys that are not
provided by VT100 for the PC 101 keyboard.
The VT100 Terminal Definition is the standard convention used to configure and conduct
emergency management tasks with UNIX-based servers. VT100 does not support all keys
on the standard PC 101-key layout, however. The VT-UTF8 convention makes available
additional keys that are not provided by VT100 for the PC 101 keyboard.
Disabled
Disables the VT-UTF8 terminal keys
DEFAULT
Enables the VT-UTF8 combination key. Support for
Enabled
ANSI/VT100 terminals
Sredir Memory Display Delay [Disabled]
Use the Sredir Memory Display Delay option to select the delay before memory
information is displayed. Configuration options are listed below
No Delay
DEFAULT
Delay 1 sec
Delay 2 sec
Delay 4 sec
6.3.8 USB Configuration
Use the USB Configuration menu (BIOS Menu 12) to read USB configuration
information and configure the USB settings.
Page 113
KINO-9453 Mini-ITX Motherboard
BIOS Menu 12: USB Configuration
USB Function [8 USB ports]
Use the USB Function BIOS option to enable or disable a specified number of USB ports.
If only two USB ports are being used, disabling the remaining six USB frees up system
resources that can be redirected elsewehere.
Disabled
USB function support disabled
2 USB Ports
Two USB ports are enabled
4 USB Ports
Four USB ports are enabled
6 USB Ports
Six USB ports are enabled
8 USB Ports
Page 114
DEFAULT
Eight USB ports are enabled
KINO-9453 Mini-ITX Motherboard
USB 2.0 Controller [Enabled]
Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller
USB 2.0 controller disabled
Disabled
Enabled
DEFAULT
USB 2.0 controller enabled
Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support.
Normally if this option is not enabled, any attached USB mouse or USB keyboard does not
become available until a USB compatible operating system is fully booted with all USB
drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard
can control the system even when there is no USB driver loaded onto the system.
Legacy USB support disabled
Disabled
Enabled
DEFAULT
Legacy USB support enabled
Legacy USB support disabled if no USB devices are
Auto
connected
USB2.0 Controller Mode [HiSpeed]
Use the USB2.0 Controller Mode option to set the speed of the USB2.0 controller.
The controller is capable of operating at 12Mb/s
FullSpeed
HiSpeed
DEFAULT
The controller is capable of operating at 480Mb/s
BIOS EHCI Handoff
Use the BIOS EHCI Handoff option for systems running OSes that do not have EHCI
hand-off support. The EHCI ownership change is managed by the EHCI driver.
Page 115
KINO-9453 Mini-ITX Motherboard
Systems with OSes that do not support EHCI can
Disabled
use the EHCI handoff functionality.
Enabled
DEFAULT
Systems with OSes that do not support EHCI cannot
use the EHCI handoff functionality.
6.3.8.1 USB Mass Storage Device Configuration
Use the USB Mass Storage Device Configuration menu (?????) to configure USB
mass storage class devices.
BIOS Menu 13: USB Mass Storage Device Configuration
USB Mass Storage Reset Delay [20 Sec]
Use the USB Mass Storage Reset Delay option to set the number of seconds POST
waits for the USB mass storage device after the start unit command.
Page 116
KINO-9453 Mini-ITX Motherboard
POST waits 10 seconds for the USB mass storage
10 Sec
device after the start unit command.
20 Sec
DEFAULT
POST waits 20 seconds for the USB mass storage
device after the start unit command.
30 Sec
POST waits 30 seconds for the USB mass storage
device after the start unit command.
40 Sec
POST waits 40 seconds for the USB mass storage
device after the start unit command.
Device ##
The Device## field lists the USB devices that are connected to the system.
Emulation Type [Auto]
Use the Emulation Type BIOS option to specify the type of emulation BIOS has to provide
for the USB device.
NOTE:
Please note that the device’s formatted type and the emulation type
provided by the BIOS must match for a device to boot properly. If both
types do not match then device’s behavior is undefined. To make sure both
types match, format the device using BIOS INT13h calls after selecting the
proper emulation option in BIOS setup. The FORMAT utility provided by
Microsoft® MS-DOS®, Microsoft® Windows® 95, and Microsoft®
Windows® 98 can be used for this purpose.
Page 117
KINO-9453 Mini-ITX Motherboard
Auto
Floppy
DEFAULT
BIOS auto-detects the current USB.
The USB device will be emulated as a floppy drive.
The device can be either A: or B: responding to
INT13h calls that return DL = 0 or DL = 1
respectively.
Forced FDD
Allows a hard disk image to be connected as a
floppy image. This option works only for drives
formatted with FAT12, FAT16 or FAT32.
Hard Disk
Allows the USB device to be emulated as hard disk
responding to INT13h calls that return DL values of
80h or above.
CDROM
Assumes the CD-ROM is formatted as bootable
media. All the devices that support block sizes
greater than 512 bytes can only be booted using this
option.
6.4 PCI/PnP
Use the PCI/PnP menu (BIOS Menu 12) to configure advanced PCI and PnP settings.
WARNING:
Setting wrong values for the BIOS selections in the PCIPnP BIOS
menu may cause the system to malfunction.
Page 118
KINO-9453 Mini-ITX Motherboard
BIOS Menu 14: PCI/PnP Configuration
Page 119
KINO-9453 Mini-ITX Motherboard
Clear NVRAM [No]
Use the Clear NVRAM option to specify if the NVRAM (Non-Volatile RAM) is cleared
when the power is turned off.
No
DEFAULT
System does not clear NVRAM during system boot
System clears NVRAM during system boot
Yes
Plug & Play O/S [No]
Use the Plug & Play O/S BIOS option to specify whether system plug and play devices
are configured by the operating system or the BIOS.
No
DEFAULT
If the operating system does not meet the Plug and Play
specifications, this option allows the BIOS to configure all the
devices in the system.
This setting allows the operating system to change the
Yes
interrupt, I/O, and DMA settings. Set this option if the system
is running Plug and Play aware operating systems.
PCI Latency Timer [64]
Use the PCI Latency Timer option to specify the PCI latency time. The latency time is
measured in units of PCI clock cycles for the PCI device latency timer register.
Configuration options are:
32
64
96
128
160
192
224
248
Page 120
DEFAULT
KINO-9453 Mini-ITX Motherboard
Allocate IRQ to PCI VGA [Yes]
Use the Allocate IRQ to PCI VGA option to restrict the system from giving the VGA
adapter card an interrupt address.
Yes
(Default)
Assigns an IRQ to a PCI VGA card if card requests IRQ
Does not assign IRQ to a PCI VGA card even if the card
No
requests an IRQ
Palette Snooping [Disabled]
Use the Palette Snooping option to enable or disable the palette snooping function.
Disabled
DEFAULT
Unless the VGA card manufacturer requires palette
snooping to be enabled, this option should be disabled.
No/
PCI devices are informed that an ISA based Graphics
Enabled
device is installed in the system so the ISA based
Graphics card functions correctly. This does not
necessarily indicate a physical ISA adapter card. The
graphics chipset can be mounted on a PCI card. Always
check with the adapter card manual first, before
modifying the default settings in the BIOS.
PCI IDE BusMaster [Enabled]
Use the PCI IDE BusMaster BIOS option to enable or prevent PCI IDE busmastering.
Busmastering is prevented
Disabled
No/Enabled
DEFAULT
IDE controller on the PCI local bus has mastering
capabilities
Page 121
KINO-9453 Mini-ITX Motherboard
OffBoard PCI/ISA IDE Card [Auto]
Use the OffBoard PCI/ISA IDE Card BIOS option to select the OffBoard PCI/ISA IDE
Card.
Auto
DEFAULT
The location of the Off Board PCI IDE adapter card is
automatically detected by the AMIBIOS.
PCI Slot 1
PCI Slot 1 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 1.
PCI Slot 2
PCI Slot 2 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 2.
PCI Slot 3
PCI Slot 3 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 3.
PCI Slot 4
PCI Slot 4 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 4.
PCI Slot 5
PCI Slot 5 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 5.
PCI Slot 6
PCI Slot 6 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 6.
IRQ# [Available]
Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral
device.
Page 122
KINO-9453 Mini-ITX Motherboard
Available
DEFAULT
The specified IRQ is available to be used by
PCI/PnP devices
The specified IRQ is reserved for use by Legacy ISA
Reserved
devices
Available IRQ addresses are:
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ 11
IRQ 14
IRQ 15
DMA Channel# [Available]
Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP
device.
Available
DEFAULT
The specified DMA is available to be used by
PCI/PnP devices
Reserved
The specified DMA is reserved for use by Legacy
ISA devices
Available DMA Channels are:
DM Channel 0
DM Channel 1
DM Channel 3
DM Channel 5
DM Channel 6
Page 123
KINO-9453 Mini-ITX Motherboard
DM Channel 7
Reserved Memory Size [Disabled]
Use the Reserved Memory Size BIOS option to specify the amount of memory that
should be reserved for legacy ISA devices.
Disabled
DEFAULT
No memory block reserved for legacy ISA devices
16K
16KB reserved for legacy ISA devices
32K
32KB reserved for legacy ISA devices
64K
54KB reserved for legacy ISA devices
6.5 Boot
Use the Boot menu (BIOS Menu 15) to configure system boot options.
BIOS Menu 15: Boot
Page 124
KINO-9453 Mini-ITX Motherboard
6.5.1 Boot Settings Configuration
Use the Boot Settings Configuration menu (BIOS Menu 15) to configure advanced
system boot options.
BIOS Menu 16: Boot Settings Configuration
Quick Boot [Enabled]
Use the Quick Boot BIOS option to make the computer speed up the boot process.
No POST procedures are skipped
Disabled
Enabled
DEFAULT
Some POST procedures are skipped to decrease
the system boot time
Quiet Boot [Disabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
Page 125
KINO-9453 Mini-ITX Motherboard
Disabled
DEFAULT
Normal POST messages displayed
OEM Logo displayed instead of POST messages
Enabled
AddOn ROM Display Mode [Force BIOS]
Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory)
messages to be displayed.
Force BIOS
DEFAULT
The system forces third party BIOS to display
during system boot.
The system displays normal information during
Keep Current
system boot.
Bootup Num-Lock [On]
Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be
modified during boot up.
Does not enable the keyboard Number Lock automatically. To
Off
use the 10-keys on the keyboard, press the Number Lock key
located on the upper left-hand corner of the 10-key pad. The
Number Lock LED on the keyboard lights up when the Number
Lock is engaged.
On
DEFAULT
Allows the Number Lock on the keyboard to be enabled
automatically when the computer system boots up. This allows
the immediate use of the 10-key numeric keypad located on
the right side of the keyboard. To confirm this, the Number
Lock LED light on the keyboard is lit.
PS/2 Mouse Support [Auto]
Use the PS/2 Mouse Support option adjusts PS/2 mouse support capabilities.
Page 126
KINO-9453 Mini-ITX Motherboard
PS/2 mouse support is disabled and prevented from
Disabled
using system resources.
Allows the system to use a PS/2 mouse.
Enabled
Auto
DEFAULT
The system auto-adjusts PS/2 mouse support.
Boot From LAN Support [Disabled]
Use the Boot From LAN Support option to enable the system to be booted from a remote
system.
Disabled
DEFAULT
Cannot be booted from a remote system through the
LAN
Enabled
Can be booted from a remote system through the
LAN
6.5.2 Boot Device Priority
Use the Boot Device Priority menu (BIOS Menu 17) to specify the boot sequence from
the available devices. Possible boot devices may include:
1st FLOPPY DRIVE
HDD
CD/DVD
Page 127
KINO-9453 Mini-ITX Motherboard
BIOS Menu 17: Boot Device Priority Settings
Page 128
KINO-9453 Mini-ITX Motherboard
6.5.3 Removable Drives
Use the Removable Drives menu (BIOS Menu 18) to specify the boot sequence of the
available FDDs. When the menu is opened, the FDDs connected to the system are listed
as shown below:
1st Drive
[1st FLOPPY DRIVE]
2nd Drive
[2nd FLOPPY DRIVE]
NOTE:
Only the drives connected to the system are shown. For example, if only
one FDD is connected only “1st Drive” is listed.
The boot sequence from the available devices is selected. If the “1st Drive” option is
selected a list of available FDDs is shown. Select the first FDD the system boots from. If
the “1st Drive” is not used for booting this option may be disabled.
BIOS Menu 18: Removable Drives
Page 129
KINO-9453 Mini-ITX Motherboard
6.6 Security
Use the Security menu (BIOS Menu 19) to set system and user passwords.
BIOS Menu 19: Security
Change Supervisor Password
Use the Change Supervisor Password to set or change a supervisor password. The
default for this option is Not Installed. If a supervisor password must be installed, select
this field and enter the password. After the password has been added, Install appears
next to Change Supervisor Password.
Change User Password
Use the Change User Password to set or change a user password. The default for this
option is Not Installed. If a user password must be installed, select this field and enter the
Page 130
KINO-9453 Mini-ITX Motherboard
password. After the password has been added, Install appears next to Change User
Password.
6.7 Chipset
Use the Chipset menu (BIOS Menu 20) to access the NorthBridge and SouthBridge
configuration menus.
WARNING:
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
BIOS Menu 20: Chipset
Page 131
KINO-9453 Mini-ITX Motherboard
6.7.1 NorthBridge Configuration
Use the NorthBridge Configuration menu (BIOS Menu 20) to configure the northbridge
chipset.
BIOS Menu 21:NorthBridge Chipset Configuration
Boots Graphics Adapter Priority [PCI/IGD]
Use the Boots Graphics Adapter Priority option to select the graphics controller used as
the primary boot device. Select either an integrated graphics controller (IGD) or a
combination of PCI graphics controller, a PCI express (PEG) controller or an IGD.
Configuration options are listed below:
IGD
PEG/IGD
PEG/PCI
PCI/PEG
Page 132
KINO-9453 Mini-ITX Motherboard
PCI/IGD
DEFAULT
Internal Graphics Mode Select [Enable, 8MB]
Use the Internal Graphic Mode Select option to specify the amount of system memory
that can be used by the Internal graphics device.
Disable
1MB of memory used by internal graphics device
Enable, 1MB
Enable, 8MB
DEFAULT
8MB of memory used by internal graphics device
PEG Port [Auto]
Use the PEG Port option to enable or disable the PCI Express port.
Auto
DEFAULT
The system automatically detects the PEG port.
Installed PEG cards cannot function.
Disabled
PEG Force X1 [Disabled]
Use the PEG Force x1 option to convert a PCI express X16 slot into a PCI express X1
slot.
Disabled
Enabled
DEFAULT
PCI express X16 slot runs in normal mode
PCI express X16 slot runs in PCI express X1
mode
6.7.1.1 Video Function Configuration
Use the Video Function Configuration menu to configure the video device connected to
the system.
Page 133
KINO-9453 Mini-ITX Motherboard
Figure 6-1: Video Function Configuration
DVMT Mode Select [DVMT Mode]
Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology
(DVMT) operating mode.
A fixed portion of graphics memory is reserved as
Fixed Mode
graphics memory.
DVMT Mode
DEFAULT
Graphics
memory
is
dynamically
allocated
according to the system and graphics needs.
Combo Mode
A fixed portion of graphics memory is reserved as
graphics memory. If more memory is needed,
graphics
memory
is
dynamically
allocated
according to the system and graphics needs.
Page 134
KINO-9453 Mini-ITX Motherboard
DVMT/FIXED Memory [128MB]
Use the DVMT/FIXED Memory option to specify the maximum amount of memory that
can be allocated as graphics memory. This option can only be configured for if DVMT
Mode or Fixed Mode is selected in the DVMT Mode Select option. If Combo Mode is
selected, the maximum amount of graphics memory is 128MB. Configuration options are
listed below.
64MB
128MB
DEFAULT
Maximum DVMT
Boot Display Device [Auto]
Use the Boot Display Device option to select the display device used by the system
when it boots. Configuration options are listed below.
Auto
DEFAULT
Flat Panel Type [1024*768]
Use the Flat Panel Type option to select the type of flat panel connected to the system.
Configuration options are listed below.
640x480
800x600
1024x768
1280x1024 (36bits)
1400x1050 (36bits)
1600x1200 (36bits)
1280x768
1680x1050 (36bits)
1920x1200 (36bits)
1024x768 (48bits)
1400x900 (36bits)
1440x900 (48bits)
1280x800
Page 135
KINO-9453 Mini-ITX Motherboard
1280x600
2048x1536 (36bits)
Local Flat Panel Scaling [Auto]
Use the Local Flat Panel Scaling option to select the method of scaling for the flat panel
screen attached to the system.
Auto
DEFAULT
Scaling is automatic
Forced Scaling
Scaling is forced
Disabled
Scaling is disabled
6.7.2 SouthBridge Chipset Configuration
The SouthBridge Chipset Configuration menu (BIOS Menu 22) the southbridge chipset
to be configured.
BIOS Menu 22:SouthBridge Chipset Configuration
Page 136
KINO-9453 Mini-ITX Motherboard
ASF Support [Enabled]
Use the ASF Support BIOS option to control the system’s ability to connect to a remote
management server.
The system will not communicate with a remote
Disabled
management server.
Enabled
DEFAULT
The Alert Standard Format (ASF) controller is activated
and can communicate with a remote management
server.
Audio Controller [AC`97 Audio Only]
The Audio Controller option allows selection of the audio controller to use.
AC`97 Audio
The on-board AC’97 controller is enabled
Only
All audio controllers are disabled
Disabled
OnBoard LAN1 (BCM5787M) [Enabled]
The OnBoard LAN1 (BCM5787M) option enables or disables the on-board LAN1.
The on-board LAN1 controller is automatically detected
Auto
and enabled
Enabled
Disabled
DEFAULT
The on-board LAN1 controller is manually enabled
The on-board LAN1 controller is manually disabled
On-board LAN2(BCM5787M) [Enabled]
The On-board LAN2(BCM5787M) option enables or disables the on-board LAN2.
Auto
The on-board LAN2 controller is automatically detected
Page 137
KINO-9453 Mini-ITX Motherboard
and enabled
Enabled
DEFAULT
Disabled
The on-board LAN2 controller is manually enabled
The on-board LAN2 controller is manually disabled
6.8 Exit
Use the Exit menu (BIOS Menu 23) to load default BIOS values, optimal failsafe values
and to save configuration changes.
BIOS Menu 23:Exit
Save Changes and Exit
Use the Save Changes and Exit option to save the changes made to the BIOS options
and to exit the BIOS configuration setup program.
Discard Changes and Exit
Page 138
KINO-9453 Mini-ITX Motherboard
Use the Discard Changes and Exit option to exit the BIOS configuration setup program
without saving the changes made to the system.
Discard Changes
Use the Discard Changes option to discard the changes and remain in the BIOS
configuration setup program.
Load Optimal Defaults
Use the Load Optimal Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F9 key can be used for this operation.
Load Failsafe Defaults
Use the Load Failsafe Defaults option to load failsafe default values for each of the
parameters on the Setup menus. F8 key can be used for this operation.
Page 139
KINO-9453 Mini-ITX Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 140
KINO-9453 Mini-ITX Motherboard
Chapter
7
7 Driver Installation
Page 141
KINO-9453 Mini-ITX Motherboard
7.1 Available Software Drivers
NOTE:
The content of the CD may vary throughout the life cycle of the product
and is subject to change without prior notice. You may visit the IEI
website or contact technical support for the latest updates.
The following drivers can be installed on the system.
Chipset driver
VGA driver
LAN driver
Installation instructions are given below.
7.2 Driver CD Auto-run
All the drivers for the KINO-9453 are on the CD that came with the system. To install the
drivers, please follow the steps below.
Step 1: Insert the CD into a CD drive connected to the system.
Step 2: The starts up automatically
Step 3: Select KINO-9453 from the initial menu.
Step 4: A new screen with a list of available drivers appears (Figure 7-1).
Page 142
KINO-9453 Mini-ITX Motherboard
Figure 7-1: Available Drivers
Step 5: Select the driver to install from the list in Figure 7-1. Step 0:
7.3 Chipset Driver Installation
To install the chipset driver, please follow the steps below:
Step 1: Select the INF driver from the list in Figure 7-1.
Step 2: A new window opens (Figure 7-2).
Page 143
KINO-9453 Mini-ITX Motherboard
Figure 7-2: Chipset Driver Installation Program
Step 3: Double click the infinst_Autol icon in Figure 7-2.
Step 4: The welcome screen in Figure 7-3 appears.
Page 144
KINO-9453 Mini-ITX Motherboard
Figure 7-3: Chipset Driver Installation Welcome Screen
Step 5: Click NEXT in Figure 7-3 to continue the installation process.
Step 6: The license agreement in Figure 7-4 appears.
Page 145
KINO-9453 Mini-ITX Motherboard
Figure 7-4: Chipset Driver Installation License Agreement
Step 7: Click YES to continue the setup.
Step 8: The Readme file in Figure 7-5 appears.
Page 146
KINO-9453 Mini-ITX Motherboard
Figure 7-5: Chipset Driver Readme File Information
Step 9: Click NEXT in Figure 7-5 to start the driver installation.
Step 10: After the driver installation process is complete, a confirmation screen (Figure
7-6) appears. Step 0:
Page 147
KINO-9453 Mini-ITX Motherboard
Figure 7-6: Chipset Driver Installation Complete
7.4 Intel Graphics Media Accelerator Driver
To install the chipset driver, please follow the steps below:
Step 1: Select the VGA driver from the list in Figure 7-1.
Step 2: A new window opens (Figure 7-7).
Page 148
KINO-9453 Mini-ITX Motherboard
Figure 7-7: Select the Operating System
Step 3: Select the operating system from those shown in Figure 7-7.
Step 4: A new window appears (Figure 7-8).
Page 149
KINO-9453 Mini-ITX Motherboard
Figure 7-8: VGA Driver
Step 5: Click the installation program icon in Figure 7-8.
Step 6: The Readme information file shown in Figure 7-9 appears.
Page 150
KINO-9453 Mini-ITX Motherboard
Figure 7-9: GMA Driver Readme File
Step 7: Click NEXT to extract the GMA driver files. See Figure 7-10.
Figure 7-10: GMA Driver File Extraction
Step 8: The welcome screen shown in Figure 7-11 appears.
Page 151
KINO-9453 Mini-ITX Motherboard
Figure 7-11: GMA Driver Installation Welcome Screen
Step 9: To continue the installation process, click NEXT.
Step 10: The license agreement in Figure 7-12 appears.
Page 152
KINO-9453 Mini-ITX Motherboard
Figure 7-12: GMA Driver License Agreement
Step 11: Click the YES in Figure 7-12 to continue.
Step 12: The installation notice shown in Figure 7-13 appears.
Figure 7-13: GMA Driver Installing Notice
Step 13: A confirmation screen shown in Figure 7-14 appears.
Page 153
KINO-9453 Mini-ITX Motherboard
Figure 7-14: GMA Driver Installation Complete
Step 14: After selecting when to restart the computer in Figure 7-14, click FINISH. Step 0:
7.5 Broadcom LAN Driver (for GbE LAN) Installation
To install the Broadcom LAN driver, please follow the steps below.
Step 1: Open Windows Control Panel (Figure 7-15).
Page 154
KINO-9453 Mini-ITX Motherboard
Figure 7-15: Access Windows Control Panel
Step 2: Double click the System icon (Figure 7-16).
Page 155
KINO-9453 Mini-ITX Motherboard
Figure 7-16: Double Click the System Icon
Step 3: Double click the Device Manager tab (Figure 7-17).
Figure 7-17: Double Click the Device Manager Tab
Step 4: A list of system hardware devices appears (Figure 7-18).
Page 156
KINO-9453 Mini-ITX Motherboard
Figure 7-18: Device Manager List
Step 5: Double click the listed device that has question marks next to it. (This means
Windows does not recognize the device).
Step 6: The Device Driver Wizard appears (Figure 7-19). Click NEXT to continue.
Page 157
KINO-9453 Mini-ITX Motherboard
Figure 7-19: Search for Suitable Driver
Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 7-20).
Click NEXT to continue.
Page 158
KINO-9453 Mini-ITX Motherboard
Figure 7-20: Locate Driver Files
Step 8: Select the proper OS folder under the “X:\3-LAN\BROADCOM BCM57xx
Drivers” directory (Figure 7-21) in the location browsing window, where “X:\” is
the system CD drive.
Figure 7-21: Location Browsing Window
Step 9: Click OK to continue. A driver files location menu window appears. Click NEXT to
continue. The driver is installed.Step 0:
Page 159
KINO-9453 Mini-ITX Motherboard
7.6 Realtek HD Audio Driver (ALC883) Installation
To install the Realtek High Definition (HD) Audio driver, please follow the steps below.
7.6.1 BIOS Setup
Step 1: Enter the BIOS setup. To do this, reboot the system and press DEL during POST.
Step 2: Go to the Southbridge Configuration menu. Set the Audio Controller option to
[Azalia]. See Chapter 6 for details.
Step 3: Press F10 to save the changes and exit the BIOS setup. The system reboots.
Step 0:
7.6.2 Driver Installation
Step 1: Insert the CD that came with the package.
Step 2: From the main driver menu, navigate to X:\4-AUDIO\AC-KIT883HD\Windows
(or other appropriate OS). X:\ represents the system CD drive. A new window
appears showing the folder contents (Figure 6-26).
Figure 7-22: 4-AUDIO\AC-KIT883HD\Windows Folder
Step 3: Double-click the WDM_R140 icon to begin the driver installation process.
Page 160
KINO-9453 Mini-ITX Motherboard
Step 4: Once the WDM_R140 icon is double clicked, the contents of the installation
package are extracted. See Figure 7-23.
Figure 7-23: HD Audio Driver Setup Extracting Files
Page 161
KINO-9453 Mini-ITX Motherboard
Step 5: The Welcome screen appears. Click NEXT. See Figure 7-24.
Figure 7-24: HD Audio Driver Setup Welcome Screen
Page 162
KINO-9453 Mini-ITX Motherboard
Step 6: The driver is automatically installed.
Step 7: After the driver installation process is complete, a confirmation screen shown in
Figure 7-25 appears.
Figure 7-25: HD Audio Driver Installation Complete
Step 8: The confirmation screen shown in Figure 7-25 allows you to restart the
computer immediately after the installation is complete or to restart the computer
later. For the settings to take effect the computer must be restarted. Once you
have decided when to restart the computer, click the “FINISH” button. Step 0:
Page 163
KINO-9453 Mini-ITX Motherboard
7.7 Realtek AC`97 Audio Driver (ALC665) Installation
To install the Realtek AC `97 audio driver, please follow the steps below.
7.7.1 BIOS Setup
Step 1: Enter the BIOS setup. To do this, reboot the system and press DEL during POST.
Step 2: Go to the Southbridge Configuration menu. Set the Audio Controller option to
[AC`97]. See Section 6.7.2 for details.
Step 3: Press F10 to save the changes and exit the BIOS setup. The system reboots.
Step 0:
7.7.2 Driver Installation
Step 1: Insert the CD that came with the package.
Step 2: From the main driver menu, navigate to X:\4-AUDIO\AC-KIT08R\Windows (or
other appropriate OS). X:\ represents the system CD drive. A new window
appears showing the folder contents (Figure 7-26).
Page 164
KINO-9453 Mini-ITX Motherboard
Figure 7-26: CD 4-AUDIO\AC-KIT08R\Windows Folder
Step 3: Double-click the Setup.exe file to begin the driver installation process.
Step 4: Once you double click the Setup icon, the install shield wizard for the audio
driver starts. See Figure 7-27.
Figure 7-27: AC`97 Audio Driver Install Shield Wizard Starting
Step 5: The Realtek Audio Setup prepares the install shield to guide you through the
rest of the setup process. See Figure 7-24.
Page 165
KINO-9453 Mini-ITX Motherboard
Figure 7-28: AC`97 Audio Driver Setup Preparation
Step 6: After the install shield is prepared, the welcome screen shown in Figure 7-29
appears. To continue the installation process, click the “NEXT” button. The install
shield starts to configure the new software as shown in Figure 7-30.
Figure 7-29: AC`97 Audio Driver Welcome Screen
Page 166
KINO-9453 Mini-ITX Motherboard
Figure 7-30: AC`97 Audio Driver Software Configuration
Page 167
KINO-9453 Mini-ITX Motherboard
Step 7: At this stage the “Digital Signal Not Found” screen appears (Figure 7-31). To
continue the installation process, click the “YES” button.
Figure 7-31: AC`97 Audio Driver Digital Signal
Page 168
KINO-9453 Mini-ITX Motherboard
Step 8: After clicking the “YES” button in Figure 7-31, the installation of the driver begins
(Figure 7-32).
Figure 7-32: AC`97 Audio Driver Installation Begins
Page 169
KINO-9453 Mini-ITX Motherboard
Step 9: After the driver installation process is complete, a confirmation screen shown in
Figure 7-33 appears.
Figure 7-33: AC`97 Audio Driver Installation Complete
Step 10: The confirmation screen shown in Figure 7-33 allows you to restart the
computer immediately after the installation is complete or to restart the computer
later. For the settings to take effect the computer must be restarted. Once you
have decided when to restart the computer, click the “FINISH” button. Step 0:
Page 170
KINO-9453 Mini-ITX Motherboard
7.8 Intel Matrix Storage Manager Installation
To install the Intel® Matrix Storage Manager driver, please follow the steps below:
Step 1: Select SATA from the list in Figure 7-1.
Step 2: A new window opens (Figure 7-34).
Figure 7-34: SATA RAID Driver Installation Program
Step 3: Double-click the INTEL folder.
Step 4: Double-click the iata62_cd.exe program icon in Figure 7-35.
Page 171
KINO-9453 Mini-ITX Motherboard
Figure 7-35: SATA RAID Setup Program Icon
Step 5:
Figure 7-36 shows the InstallShield Wizard preparing to guide the user
through the rest of the process.
Figure 7-36: InstallShield Wizard Setup Screen
Page 172
KINO-9453 Mini-ITX Motherboard
Step 6: Figure 7-37 shows the Matrix Storage Manager software configuring the
installation process.
Figure 7-37: Matrix Storage Manager Setup Screen
Step 7: Figure 7-38 shows the Matrix Storage Manager welcome screen.
Figure 7-38: Matrix Storage Manager Welcome Screen
Page 173
KINO-9453 Mini-ITX Motherboard
Step 8: Click NEXT and a warning appears (Figure 7-39). Read the warning carefully
and decide whether or not to continue the installation process.
Figure 7-39: Matrix Storage Manager Warning Screen
Step 9: Click NEXT and a license agreement appears (Figure 7-40).
Figure 7-40: Matrix Storage Manager License Agreement
Page 174
KINO-9453 Mini-ITX Motherboard
Step 10: Read the license agreement. To accept the terms and conditions stipulated in
the license agreement shown, click YES and the Readme information file shown
in Figure 7-41 appears.
Figure 7-41: Matrix Storage Manager Readme File
Step 11: Read the Readme file information and click NEXT.
Page 175
KINO-9453 Mini-ITX Motherboard
Step 12: After the driver installation process is complete, a confirmation screen appears
(Figure 7-42).
Figure 7-42: Matrix Storage Manager Setup Complete
Step 13: The confirmation screen offers the option of restarting the computer now or later.
For the settings to take effect, the computer must be restarted. Click FINISH to
restart the computer. Step 0:
Page 176
KINO-9453 Mini-ITX Motherboard
Appendix
A
A BIOS Options
Page 177
KINO-9453 Mini-ITX Motherboard
System Overview .................................................................................................................86
System Time [xx:xx:xx] .......................................................................................................87
System Date [xx/xx/xx] ........................................................................................................87
ATA/IDE Configuration [Enhanced]....................................................................................90
Configure SATA as [IDE] .....................................................................................................91
Configure SATA Channels [Before PATA]..........................................................................91
IDE Master and IDE Slave....................................................................................................91
Type [Auto] ...........................................................................................................................92
ZIP..........................................................................................................................................93
LS-120 ...................................................................................................................................93
LBA/Large Mode [Auto].......................................................................................................93
Block (Multi-Sector Transfer) [Auto] ..................................................................................94
PIO Mode [Auto]...................................................................................................................94
DMA Mode [Auto] .................................................................................................................95
S.M.A.R.T [Auto]...................................................................................................................96
32Bit Data Transfer [Enabled].............................................................................................96
Serial Port1 Address [3F8/IRQ4].........................................................................................97
Serial Port1 Mode [Normal].................................................................................................98
Serial Port2 Address [2F8/IRQ3].........................................................................................98
Serial Port2 Mode [Normal].................................................................................................98
Serial Port3 Address [3E8] ..................................................................................................98
Serial Port3 IRQ [11] ............................................................................................................99
Serial Port4 Address [2E8] ..................................................................................................99
Serial Port4 IRQ [10] ............................................................................................................99
CPU FAN Mode Setting [Full On Mode] .......................................................................... 100
CPU Temp. Limit of OFF [000] ......................................................................................... 101
CPU Temp. Limit of Start [020]......................................................................................... 101
CPU Temp. Limit of Full [080] .......................................................................................... 102
CPU Fan Start PWM [070]................................................................................................. 103
Slope PWM 1 [1 PWM] ...................................................................................................... 103
CPU Fan PWM Control [100] ............................................................................................ 104
Hardware Health Monitoring ............................................................................................ 104
Suspend Mode [S3 (STR)] ................................................................................................ 106
Power Management/APM [Enabled]................................................................................ 107
Page 178
KINO-9453 Mini-ITX Motherboard
Power Supply Mode [ATX] ............................................................................................... 108
Restore on AC Power Loss by IO [Power Off] ............................................................... 108
Resume on Ring [Disabled] ............................................................................................. 108
Resume on PME# [Disabled] ........................................................................................... 108
Resume On RTC Alarm [Disabled] .................................................................................. 109
RTC Alarm Date (Days)..................................................................................................... 109
System Time ...................................................................................................................... 109
Resume On PCI-Express WAKE# [Enabled] .................................................................. 109
Remote Access [Disabled]................................................................................................110
Serial Port Number ............................................................................................................110
Serial Port Mode.................................................................................................................110
Flow Control .......................................................................................................................110
Redirection after BIOS POST............................................................................................110
Terminal Type .....................................................................................................................111
VT-UTF8 Combo Key Support...........................................................................................111
Sredir Memory Display Delay ...........................................................................................111
Serial Port Number [COM1]...............................................................................................111
Base Address, IRQ [3F8h,4]..............................................................................................111
Serial Port Mode [115200 8,n,1] ........................................................................................111
Flow Control [None]...........................................................................................................112
Redirection After BIOS POST [Always] ...........................................................................112
Terminal Type [ANSI] .........................................................................................................112
VT-UTF8 Combo Key Support [Disabled] ........................................................................113
Sredir Memory Display Delay [Disabled].........................................................................113
USB Function [8 USB ports] .............................................................................................114
USB 2.0 Controller [Enabled]............................................................................................115
Legacy USB Support [Enabled]........................................................................................115
USB2.0 Controller Mode [HiSpeed] ..................................................................................115
BIOS EHCI Handoff ............................................................................................................115
USB Mass Storage Reset Delay [20 Sec] .........................................................................116
Device ##.............................................................................................................................117
Emulation Type [Auto] .......................................................................................................117
Clear NVRAM [No]............................................................................................................. 120
Plug & Play O/S [No]......................................................................................................... 120
PCI Latency Timer [64] ..................................................................................................... 120
Page 179
KINO-9453 Mini-ITX Motherboard
Allocate IRQ to PCI VGA [Yes]......................................................................................... 121
Palette Snooping [Disabled] ............................................................................................ 121
PCI IDE BusMaster [Enabled] .......................................................................................... 121
OffBoard PCI/ISA IDE Card [Auto]................................................................................... 122
IRQ# [Available] .............................................................................................................. 122
DMA Channel# [Available]................................................................................................ 123
Reserved Memory Size [Disabled] .................................................................................. 124
Quick Boot [Enabled] ....................................................................................................... 125
Quiet Boot [Disabled] ....................................................................................................... 125
AddOn ROM Display Mode [Force BIOS] ....................................................................... 126
Bootup Num-Lock [On] .................................................................................................... 126
PS/2 Mouse Support [Auto] ............................................................................................. 126
Boot From LAN Support [Disabled] ................................................................................ 127
Change Supervisor Password ......................................................................................... 130
Change User Password.................................................................................................... 130
Boots Graphics Adapter Priority [PCI/IGD] .................................................................... 132
Internal Graphics Mode Select [Enable, 8MB] ............................................................... 133
PEG Port [Auto]................................................................................................................. 133
PEG Force X1 [Disabled].................................................................................................. 133
DVMT Mode Select [DVMT Mode].................................................................................... 134
DVMT/FIXED Memory [128MB] ........................................................................................ 135
Boot Display Device [Auto].............................................................................................. 135
Flat Panel Type [1024*768] ............................................................................................... 135
Local Flat Panel Scaling [Auto] ....................................................................................... 136
ASF Support [Enabled]..................................................................................................... 137
Audio Controller [AC`97 Audio Only].............................................................................. 137
OnBoard LAN1 (BCM5787M) [Enabled] .......................................................................... 137
On-board LAN2(BCM5787M) [Enabled] .......................................................................... 137
Save Changes and Exit .................................................................................................... 138
Discard Changes and Exit................................................................................................ 138
Discard Changes............................................................................................................... 139
Load Optimal Defaults ...................................................................................................... 139
Load Failsafe Defaults ...................................................................................................... 139
Page 180
KINO-9453 Mini-ITX Motherboard
Appendix
B
B DIO Interface
Page 181
KINO-9453 Mini-ITX Motherboard
B.1 DIO Interface Introduction
The DIO connector on the KINO-9453 is interfaced to GIO ports on the iTE Super I/O
chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs
and digital outputs are generally control signals that control the on/off circuit of external
devices or TTL devices. Data can be read or written to the selected address to enable the
DIO functions.
NOTE:
For further information, please refer to the datasheet for the iTE Super
I/O chipset.
B.2 DIO Connector Pinouts
The following table describes how the DIO connector pins are connected to the Super I/O
GPIO port 1.
Pin No
Description
Super I/O Pin
Super I/O Pin Descripton
1
Ground
N/A
N/A
2
VCC
N/A
N/A
3
Output 0
GP14
General purpose I/O port 1 bit 4.
4
Output 1
GP15
General purpose I/O port 1 bit 5.
5
Output 2
GP16
General purpose I/O port 1 bit 6.
6
Output 3
GP17
General purpose I/O port 1 bit 7.
7
Input 0
GP10
General purpose I/O port 1 bit 0.
8
Input 1
GP11
General purpose I/O port 1 bit 1
9
Input 2
GP12
General purpose I/O port 1 bit 2
10
Input 3
GP13
General purpose I/O port 1 bit 3
Page 182
KINO-9453 Mini-ITX Motherboard
B.3 Assembly Language Samples
B.3.1 Enable the DIO Input Function
The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable
digital I/O input functions is listed below.
MOV
AX, 6F08H
Sets the digital port as input
INT
15H
Initiates the INT 15H BIOS call
B.3.2 Enable the DIO Output Function
The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable
digital I/O output functions is listed below.
MOV
AX, 6F09H
MOV
BL, 09H
INT
15H
Sets the digital port as output
Initiates the INT 15H BIOS call
Page 183
KINO-9453 Mini-ITX Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 184
KINO-9453 Mini-ITX Motherboard
Appendix
C
C Watchdog Timer
Page 185
KINO-9453 Mini-ITX Motherboard
NOTE:
The following discussion applies to DOS environment. IEI support is
contacted or the IEI website visited for specific drivers for more
sophisticated operating systems, e.g., Windows and Linux.
The Watchdog Timer is provided to ensure that standalone systems can always recover
from catastrophic conditions that cause the CPU to crash. This condition may have
occurred by external EMI or a software bug. When the CPU stops working correctly,
Watchdog Timer either performs a hardware reset (cold boot) or a Non-Maskable Interrupt
(NMI) to bring the system back to a known state.
A BIOS function call (INT 15H) is used to control the Watchdog Timer:
INT 15H:
AH – 6FH Sub-function:
AL – 2:
Sets the Watchdog Timer’s period.
BL:
Time-out value (Its unit-second is dependent on the item “Watchdog
Timer unit select” in CMOS setup).
Table C-1: AH-6FH Sub-function
Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value
is not zero, the Watchdog Timer starts counting down. While the timer value reaches zero,
the system resets. To ensure that this reset condition does not occur, calling sub-function
2 must periodically refresh the Watchdog Timer. However, the Watchdog timer is disabled
if the time-out value is set to zero.
A tolerance of at least 10% must be maintained to avoid unknown routines within the
operating system (DOS), such as disk I/O that can be very time-consuming.
Page 186
KINO-9453 Mini-ITX Motherboard
NOTE:
When exiting a program it is necessary to disable the Watchdog Timer,
otherwise the system resets.
Example program:
; INITIAL TIMER PERIOD COUNTER
;
W_LOOP:
MOV
AX, 6F02H
;setting the time-out value
MOV
BL, 30
;time-out value is 48 seconds
INT
15H
;
; ADD THE APPLICATION PROGRAM HERE
;
CMP
EXIT_AP, 1
JNE
W_LOOP
;is the application over?
;No, restart the application
MOV
AX, 6F02H
;disable Watchdog Timer
MOV
BL, 0
;
INT
15H
;
; EXIT ;
Page 187
KINO-9453 Mini-ITX Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 188
KINO-9453 Mini-ITX Motherboard
Appendix
D
D Address Mapping
Page 189
KINO-9453 Mini-ITX Motherboard
D.1 Address Map
I/O address Range
Description
000-01F
DMA Controller
020-021
Interrupt Controller
040-043
System time
060-06F
Keyboard Controller
070-07F
System CMOS/Real time Clock
080-09F
DMA Controller
0A0-0A1
Interrupt Controller
0C0-0DF
DMA Controller
0F0-0FF
Numeric data processor
1F0-1F7
Primary IDE Channel
2F8-2FF
Serial Port 2 (COM2)
378-37F
Parallel Printer Port 1 (LPT1)
3B0-3BB
Intel Graphics Controller
3C0-3DF
Intel Graphics Controller
3F6-3F6
Primary IDE Channel
3F7-3F7
Standard floppy disk controller
3F8-3FF
Serial Port 1 (COM1)
Table D-1: IO Address Map
D.2 1st MB Memory Address Map
Memory address
Description
00000-9FFFF
System memory
A0000-BFFFF
VGA buffer
F0000-FFFFF
System BIOS
1000000-
Extend BIOS
Table D-2: 1st MB Memory Address Map
Page 190
KINO-9453 Mini-ITX Motherboard
D.3 IRQ Mapping Table
IRQ0
System Timer IRQ8
RTC clock
IRQ1
Keyboard
IRQ9
ACPI
IRQ2
Available
IRQ10
LAN
IRQ3
COM2
IRQ11
LAN/USB2.0/SATA
IRQ4
COM1
IRQ12
PS/2 mouse
IRQ5
SMBus Controller IRQ13
FPU
IRQ6
FDC
IRQ14
Primary IDE
IRQ7
Available
IRQ15
Secondary IDE
Table D-3: IRQ Mapping Table
D.4 DMA Channel Assignments
Channel
Function
0
Available
1
Available
2
Floppy disk (8-bit transfer)
3
Available
4
Cascade for DMA controller 1
5
Available
6
Available
7
Available
Table D-4: IRQ Mapping Table
Page 191
KINO-9453 Mini-ITX Motherboard
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 192
KINO-9453 Mini-ITX Motherboard
Appendix
E
®
E Intel Matrix Storage
Manager
Page 193
KINO-9453 Mini-ITX Motherboard
E.1 Introduction
The Intel® ICH7R chipset can provide data protection for serial ATA (SATA) disks via the
Intel® Matrix Storage Manager using one of three fault-tolerant RAID levels: RAID 1, 5 or
10. When using two hard drives, matrix RAID allows RAID 0 and RAID 1 functions to be
combined, where critical files can be stored on RAID 1, and RAID 0 can be used for
non-critical items such as software. RAID 5 and RAID 0 can be combined to provide
higher performance, capacity, and fault tolerance.
CAUTION!
A configured RAID volume (which may consist of multiple hard drives) appears
to an operating system as a contingent storage space. The operating system
will not be able to distinguish the physical disk drives contained in a RAID
configuration.
E.1.1 Precautions
One key benefit a RAID configuration brings is that a single hard drive can fail within a
RAID array without damaging data. With RAID1 array, a failed drive can be replaced and
the RAID configuration restored.
WARNING!
Irrecoverable data loss occurs if a working drive is removed when trying to
remove a failed drive. It is strongly recommended to mark the physical
connections of all SATA disk drives. Drive locations can be identified by
attaching stickers to the drive bays. If a drive member of a RAID array should
fail, the failed drive can then be correctly identified.
Page 194
KINO-9453 Mini-ITX Motherboard
CAUTION!
Do not accidentally disconnect the SATA drive cables. Carefully route the
cables within the chassis to avoid system down time.
E.2 Features and Benefits
Supports RAID levels 0, 1, 5 and 10
Supports connectivity to two or more disk drives
Supported Operating Systems include: Windows XP, Windows Server 2003
and Windows Vista
E.3 Accessing the Intel® Matrix Storage Manager
To access the Intel® Matrix Storage Manager, please follow the steps below.
Step 1: Connect SATA drives to the system. Connect two or more SATA drives to the
system. Make sure the drives have the same capacity, are the same type and
have the same speed.
NOTE:
Make sure the SATA drives are EXACTLY the same when they are configured
in a RAID configuration. If they are not the same size, disk drive capacity is
sacrificed and overall performance affected.
Step 2: Enable SATA drives in BIOS. Start the computer and access the BIOS setup
program. Enable SATA support for all IDE devices. Refer to the applicable BIOS
configuration section in this user manual.
Page 195
KINO-9453 Mini-ITX Motherboard
Step 3: Save and Exit BIOS. After the SATA support option is enabled, save and exit
the BIOS.
Step 4: Reboot the system. Reboot the system after saving and exiting the BIOS.
Step 5: Press Ctrl+I. During the system boot process, press Ctrl+I when prompted to
enter the RAID configuration software.
Step 6: Configure the RAID settings. Use the Intel® Matrix Storage Manager to
configure the RAID array. Brief descriptions of configuration options are given
below.
Step 7: Install the OS. After the RAID array has been configured, install the OS. To do
this, please refer to the documentation that came with the OS.Step 0:
E.4 RAID Configuration
E.4.1 Creating a RAID Volume
WARNING!
All data previously stored on the member drives of a RAID configuration are
destroyed during the RAID initialization process. If “used” drives are used to
create a RAID array, make sure the data has been moved or backed up
before creating a RAID array out of the disk drives.
Page 196
KINO-9453 Mini-ITX Motherboard
Step 1: Select “Create RAID Volume.” Use the arrow keys to highlight Create RAID
Volume and press ENTER. See Figure E-1.
Figure E-1: Matrix Storage Manager Main Menu
Step 2: Name the RAID volume. Enter a name for the RAID volume, or press ENTER to
accept the default volume name. Upper and lower case alphabetic, numeric,
space, and underscore characters are all applicable for naming an array. See
Figure E-2.
Figure E-2: Create RAID Volume Name
Page 197
KINO-9453 Mini-ITX Motherboard
Step 3: Choose the RAID level. Select a RAID level from the list. RAID levels include
RAID 0, 1, 5 and 10. See Figure E-3.
NOTE:
RAID 0 and RAID1 levels require a minimum of two hard drives.
RAID 10 level requires a minimum of four hard drives.
RAID5 level requires a minimum of three hard drives.
Figure E-3: Choose the Raid Level
Page 198
KINO-9453 Mini-ITX Motherboard
Step 4: Select the Stripe Size. Select a stripe size from the list. See Figure E-4.
Figure E-4: Select the Stripe Size
Step 5: Enter the Volume Capacity. Enter the volume capacity, or press ENTER to
accept the default capacity. See Figure E-5.
Figure E-5: Enter the Volume Capacity
Page 199
KINO-9453 Mini-ITX Motherboard
Step 6: Create the RAID Volume. Press ENTER to create the RAID volume as specified.
See Figure E-6.
Figure E-6: Create the RAID Volume
Step 7: Create RAID Volume Verification. After reading the warning, press Y to create
the RAID volume as specified, or N to return to the Create RAID Volume menu.
See Figure E-7. Step 0:
Figure E-7: Create RAID Volume Verification
Page 200
KINO-9453 Mini-ITX Motherboard
E.4.2 Deleting a RAID Volume
WARNING!
All data stored on the member drives of a RAID volume are destroyed during
the RAID deletion process. Make sure any data to be saved has been moved
or backed up before deleting a RAID volume.
Step 1: Select “Delete RAID Volume.” Use the arrow keys to highlight Delete RAID
Volume and press ENTER. See Figure E-8.
Figure E-8: Delete RAID Volume Menu
Page 201
KINO-9453 Mini-ITX Motherboard
Step 2: Select RAID Volume to be Deleted. Use the arrow keys to highlight the RAID
volume to be deleted and press ENTER. See Figure E-9.
Figure E-9: Select RAID Volume to be Deleted
Step 3: Delete Volume Verification. After reading the warning, press Y to delete the
specified RAID volume, or N to return to the Delete Volume menu.
See Figure E-10.
Figure E-10: Delete Volume Verification
Page 202
KINO-9453 Mini-ITX Motherboard
Step 4: Non-RAID Disks. After deleting the RAID volume, the disks belonging to the
volume will be shown as non-RAID disks. See Figure E-11. Step 0:
Figure E-11: Non-RAID Disks
E.4.3 Resetting a Disk to Non-RAID
WARNING!
All data stored on the disk drive of a RAID volume is destroyed when
resetting it to non-RAID. Make sure any data to be saved has been moved or
backed up before resetting a disk to non-RAID.
Page 203
KINO-9453 Mini-ITX Motherboard
Step 1: Select “Reset Disk to Non-RAID.” Use the arrow keys to highlight Reset Disk
to Non-RAID and press ENTER. See Figure E-12.
Figure E-12: Reset Disk to Non-RAID Menu
Step 2: Select Disks to Reset. Use the arrow keys to scroll through the disk drives and
press SPACE to select which drives are to be reset as non-RAID. After all the
disks to be reset have been chosen, press ENTER. See Figure E-13.
Figure E-13: Select Disk to Reset
Page 204
KINO-9453 Mini-ITX Motherboard
Step 3: Reset Disk Verification. After reading the warning, press Y to reset the
selected disks as non-RAID, or N to return to the Reset RAID Data menu.
See Figure E-14.
Figure E-14: Reset Disk Verification
Step 4: Disk Drive and RAID Volume Status. After the disk drives have been reset, the
Matrix Storage Manager Main menu is shown indicating the status of the RAID
volumes and disk drives. See Figure E-15. Step 0:
Figure E-15: Disk Drive and RAID Volume Status
Page 205
KINO-9453 Mini-ITX Motherboard
E.4.4 Exiting the Matrix Storage Manager
Step 1: Select “Exit.” Use the arrow keys to highlight Exit and press ENTER.
See Figure E-16.
Figure E-16: Exit Menu
Step 2: Exit Verification. Press Y to exit the Matrix Storage Manager, or N to return to
the Main menu. See Figure E-17. Step 0:
Figure E-17: Exit Verification
Page 206
KINO-9453 Mini-ITX Motherboard
F Index
Page 207
KINO-9453 Mini-ITX Motherboard
location ..................................................67
A
ACPI ................................................106, 107
Advanced Power Management .......108, 138
airflow ........................................................71
ALC655 CODEC........................................15
anti-static precautions..........................24, 56
anti-static pad ..................................24, 56
anti-static wristband.........................24, 56
handling ...........................................24, 56
self-grounding..................................24, 56
ATX power .................................................42
Audio jacks ............................................4, 47
B
settings ..................................................66
CMOS ........................................................66
clear CMOS jumper ...............................66
COM 3
COM 3 function select ...........................67
COM 3 function select jumper ...................67
location ..................................................68
settings ..................................................68
connectors, pinouts and location
Digital Input/Output................................34
Fan.........................................................32
Front Panel ............................................33
IDE.........................................................35
Internal USB ..........................................46
LCD Backlight........................................37
BIOS .. 18, 85, 86, 87, 88, 89, 90, 91, 92, 93,
LVDS......................................................38
97, 98, 101, 105, 106, 107, 108, 110, 111,
Mini PCI .................................................40
113, 114, 115, 117, 119, 120, 125, 126,
Power ....................................................41
127, 128, 129, 130, 131, 132, 133, 137,
SATA......................................................44
139
Serial Port (10-pin) ................................43
BIOS chipset..............................................18
Serial Port (14-pin..................................42
SPDIF ....................................................45
C
cables ........................................................72
dual RS-232 cable.................................73
chassis...........................................32, 47, 71
installation..............................................71
chipset........................................................12
northbridge ............................................12
chipset driver ...................................144, 149
Clear CMOS ..........................................4, 65
clear CMOS jumper ...................................66
Page 208
cooling........................................................71
airflow ....................................................71
cooling fan........................................... 62, 63
cooling kit installation .................................62
CPU
cooling fan .............................................62
heat sink ................................................62
installation..............................................59
CPU ...........................................................11
compatible .............................................11
CRT monitor...............................................79
KINO-9453 Mini-ITX Motherboard
D
FDD............................................................97
front panel ..................................................34
DB-15 connector..................................79, 80
Front panel...................................................4
DB-9...........................................................53
front side bus ...............................................2
DDR2 ...........................................................4
FSB ............................................................90
Digital I/O .....................................................4
dimensions...................................................8
H
board .......................................................8
external peripheral interface connector
heat sink.....................................................62
panel ...................................................9
DIMM .........................................................64
I
installation..............................................64
IDE device..................................................72
specifcations..........................................64
connector...............................................72
DVI port device ..........................................76
IDE flat cable .........................................72
IDE flat cable..............................................72
E
electrostatic discharge .........................24, 56
Enhanced Hardware Monitor.....................20
IDE interface ..............................................16
installation checklist ...................................58
IrDA ...........................................................99
Ethernet .....................................................76
RJ-45 cable connector ..........................76
J
external peripheral interface ......................76
jumper ........................................................65
connection .............................................76
clear CMOS ...........................................66
connectors.............................................76
COM 3 function select ...........................67
External Peripheral Interface Connectors
Audio Connector....................................48
jumper configuration ..............................65
LVDS voltage selection..........................68
CRT Connector......................................48
DVI Connector.......................................49
K
Ethernet Connector ...............................50
Keyboard/Mouse Connector .................52
Serial Port Connector ............................53
keyboard ............................................. 76, 81
keyboard controller ....................................20
USB Connector .....................................54
L
F
fan speed controller ...................................20
LCD backlight........................................ 4, 37
LCD voltage .......................................... 4, 66
Page 209
KINO-9453 Mini-ITX Motherboard
LPC bus .....................................................18
R
LPC interface .......................................16, 19
LVDS display .............................................68
real time clock ............................................17
voltage select ........................................68
REALTEK ALC655 CODEC.......................15
LVDS voltage selection jumper..................68
RJ-45 ...................................... 47, 50, 51, 52
location ..................................................69
RJ-45 connector.........................................77
settings ..................................................69
RJ-45 Ethernet
connection .............................................77
M
RJ-45 Ethernet...........................................77
rotation signal.............................................33
Matrix Storage Manager ..........................194
memory module installation .......................64
memory support.........................................12
RS-232.......................................................73
cable connection....................................73
dual cable ..............................................73
Mini PCI ...........................................4, 40, 41
motherboard ..............................................71
S
installation..............................................71
mouse ........................................................76
SATA ............................................................2
controller................................................17
N
SATA drive..................................................74
cables ....................................................74
Northbridge ................................................33
northbridge chipset ....................................12
connection .............................................74
power cable ...........................................74
SATA II .................................................. 4, 44
P
Serial Device
PCI ...................................................4, 40, 41
connection .............................................80
PCI Express GbE controller.......................18
Serial Device..............................................80
PCI interface ..............................................17
serial ports .................................................20
PCIe bus ....................................................18
six-channel audio CODEC.........................15
peripheral device cables............................72
socket 479 CPU
processors ................................................. 11
cooling kit...............................................62
PS/2 .....................................................52, 53
cooling kit installation.............................62
PS/2 connector ..........................................81
installation..............................................59
PS/2 keyboard
connection .............................................81
SPDIF ............................................. 4, 45, 46
Super I/O chipset ................................ 18, 19
system voltages ...................................... 101
Page 210
KINO-9453 Mini-ITX Motherboard
T
controller................................................17
USB 2.0....................................4, 47, 48, 116
technical specifications................................5
temperature .............................................101
V
U
VGA ...........................................................79
VGA monitor...............................................79
unpacking ..................................................24
connection .............................................79
unpacking checklist ...............................25
unpacking precautions ..........................24
W
USB ..................................... 2, 114, 115, 116
warranty validation .....................................58
Page 211
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement