advertisement
PCAN-PCI Express
CAN Interface for PCI Express
User Manual
Document version 3.3.1 (2014-05-12)
PCAN-PCI Express – User Manual
Products taken into account
Product Name
PCAN-PCI Express Single
Channel galv. isolated
PCAN-PCI Express Dual
Channel galv. Isolated
PCAN-PCI Express Four
Channel galv. isolated
Model Part Number Ser. No.
One CAN channel IPEH-003026
Two CAN channels IPEH-003027 starting at
01000
Four CAN channels IPEH-003040
The cover picture shows the product PCAN-PCI Express Four Channel galvanic isolated. Other product versions have an identical form factor but vary in equipment.
CANopen® and CiA® are registered community trade marks of CAN in Automation e.v.
All other product names mentioned in this manual may be the trademarks or registered trademarks of their respective companies. They are not explicitly marked by “™” and “®”.
© 2014 PEAK-System Technik GmbH
PEAK-System Technik GmbH
Otto-Roehm-Strasse 69
64293 Darmstadt
Germany
Phone: +49 (0)6151 8173-20
Fax: +49 (0)6151 8173-29 www.peak-system.com [email protected]
Document version 3.3.1 (2014-05-12)
2
PCAN-PCI Express – User Manual
Contents
2 Installing the Software and the Card
Slot Bracket with D-Sub Connectors
Supplying External Devices via the CAN
CAN Monitor PCAN-View for Windows
Linking Own Programs with PCAN-Basic
Principle Description of the API
3
PCAN-PCI Express – User Manual
1
Introduction
The PCAN-PCI Express card enables the connection of a PC with
PCI Express slots to CAN networks. The card is available as a single, dual, or four-channel version. Device drivers and programming interfaces exist for different operating systems, so programs can easily access a connected CAN bus.
Tip: At the end of this manual (Appendix C) you can find a
Quick Reference with brief information about the installation
and operation of the PCAN-PCI Express card.
1.1
Properties at a Glance
PC plug-in card (PCIe-x1) for PCI Express slots
1, 2 or 4 High-speed CAN channels (ISO 11898-2)
Bit rates from 5 kbit/s up to 1 Mbit/s
Compliant CAN specifications 2.0A (11-bit ID) and 2.0B (29-bit ID)
CAN bus connection via D-Sub,
9-pin (in accordance with CiA® 102)
CAN controller FPGA implementation (SJA1000 compatible)
NXP PCA82C251 CAN transceiver
Galvanic isolation on the CAN connection up to 500 V, separate for each CAN channel
5-Volts supply to the CAN connection can be connected through a solder jumper, e.g. for external bus converter
Extended operating temperature range from -40 to 85 °C
(-40 to 185 °F)
4
PCAN-PCI Express – User Manual
Note: This manual describes the use of the PCAN-PCI Express card with Windows. You can find device drivers for Linux and the corresponding application information on the provided DVD in the directory branch Develop and on our website under www.peak-system.com/linux.
1.2
System Requirements
A vacant PCI Express slot in the computer
Operating system Windows 8, 7, Vista (32/64-bit) or Linux (32/64-bit)
1.3
Scope of Supply
PCAN-PCI Express card
Slot bracket with D-Sub connectors for the CAN bus
(only four-channel version)
Device drivers for Windows 8, 7, Vista and Linux (32/64-bit)
PCAN-View CAN monitor for Windows 8, 7, Vista (32/64-bit)
PCAN-Basic programming interface consisting of an interface
DLL, examples, and header files for all common programming languages
Manual in PDF format
5
PCAN-PCI Express – User Manual
2
Installing the Software and
the Card
This chapter covers the software setup for the PCAN-PCI Express card (short: PCIe card) under Windows and the installation of the card in the computer.
Setup the driver before installing the PCIe card.
Do the following to install the driver:
1. Make sure that you are logged in as user with administrator privileges (not needed for normal use of the PCIe card later on).
2. Insert the supplied DVD into the appropriate drive of the computer. Usually a navigation program appears a few moments later. If not, start the file Intro.exe from the root directory of the DVD.
3. On the page English > Drivers activate the entry PCAN-PCI.
4. Click on Install now. The setup program for the driver is executed.
5. Follow the instructions of the setup program.
Tip: If you don't want to install the CAN monitor PCAN-View for
Windows onto the hard disk together with the driver, you have the option to start the program later directly from DVD without prior installation.
6
PCAN-PCI Express – User Manual
Do the following to install the PCIe card into the computer:
Attention! Electrostatic discharge (ESD) can damage or destroy components on the PCAN-PCI Express card. Take precautions to avoid ESD when handling the card.
1. Four-channel version only: Connect the 10-pin connector of
CAN ports 3 and 4 with a cable from the slot bracket.
Figure 1: Position of the sockets for the CAN connection,
CAN 3 (upper left position), CAN 4 (upper right position)
2. Shut down the computer and switch it off.
3. Disconnect the computer from the power supply.
4. Open the computer's casing.
5. If applicable, remove a front blind in front of the desired slot of the PCIe card. The additional slot bracket with connectors used by the four-channel version needs a further place.
6. Insert the PCIe card into a vacant PCI Express slot. For details refer to the documentation of the computer.
7. Close the computer's casing.
8. Reconnect the power supply of the computer.
7
PCAN-PCI Express – User Manual
Do the following to complete the initialization:
1. Turn on the computer and start Windows. Make sure again that you are logged in as user with administrator privileges.
Windows notifies that new hardware has been detected.
2. The drivers are found and installed by Windows.
3. Afterwards you can work as user with restricted rights again.
After the initialization process is finished successfully you can find the entry “PCAN-PCI Express” in the branch “CAN-Hardware” of the
Windows Device Manager.
8
PCAN-PCI Express – User Manual
3
Connecting the CAN Bus
3.1
D-Sub connector
A High-speed CAN bus (ISO 11898-2) is connected to the 9-pin
D-Sub connector. The pin assignment for CAN corresponds to the specification CiA® 102.
Figure 2: Pin assignment of High-speed CAN connection
(view onto a male connector on the PCAN-PCI Express card)
With pin 1 devices with low power consumption (e.g. bus converters) can be directly supplied via the CAN connector. At delivery this pin is not assigned. You can find a detailed description in the follo-
Tip: You can connect a CAN bus with a different transmission standard via a bus converter. PEAK-System offers different bus converter modules (e.g. PCAN-TJA1054 for a Low-speed CAN bus according to ISO 11898-3).
9
PCAN-PCI Express – User Manual
The pin assignment between the D-Sub port and the 10-pin connector on the PCAN-PCI Express Four Channel card for channel 3 and 4 is as follows:
Figure 3: Numbering at the 10-pin connector
Pin Assignment
1 +5 V (optional)
2 GND
3 CAN_L
4 CAN_H
5 GND
Assignment
D-Sub
1
6
2
7
3
8
4
9
5
10
PCAN-PCI Express – User Manual
3.1.1
Slot Bracket with D-Sub Connectors
Figure 4: Dual channel slot bracket
Four-channel version only: To connect a CAN bus to the PCAN-PCI
Express card, use the supplied slot bracket. After you have connected the cables from the slot bracket with the 10-pin sockets of
CAN port 3 and 4, you can connect the CAN busses with the
D-Sub sockets.
11
PCAN-PCI Express – User Manual
3.2
Supplying External Devices via the CAN
Connector
A 5-Volt supply can optionally be routed to pin 1 of a D-Sub connector by setting solder bridges on the PCAN-PCI Express card (independently for each connector on the dual or four-channel version).
Thus external devices with low power consumption (e.g. bus converters) can be directly supplied via the CAN connector. By using interconnected DC/DC converter the current output is limited to 50 mA.
Proceed as follows to activate the 5-Volt supply:
Attention! Electrostatic discharge (ESD) can damage or destroy components on the PCAN-PCI Express card. Take precautions to avoid ESD when handling the card.
Set the solder bridge(s) on the PCIe card according to the desired settings. During this procedure take especially care not to produce unwanted short circuits on the card.
Figure 5 shows the positions of the solder fields on the PCIe card.
The table below contains the possible settings.
12
PCAN-PCI Express – User Manual
Figure 5: Position of the solder fields on the board’s bottom side for a 5-Volt supply at the CAN connection
5-Volt supply →
CAN 1
CAN 2
CAN 3
CAN 4
Jumper
JP100
JP200
JP300
JP400
None Pin 1
Attention! Risk of short circuit! If the option described in this section is activated, you may only connect or disconnect CAN cables or peripheral systems (e.g. bus converters) to or from the PCIe card while the computer is de-energized.
13
PCAN-PCI Express – User Manual
3.3
Cabling
3.3.1
Termination
A High-speed CAN bus (ISO 11898-2) must be terminated on both ends with 120 Ohms. Otherwise, there are interfering signal reflections and the transceivers of the connected CAN nodes (CANinterface, control device) will not work.
The PCAN-PCI Express card does not have an internal termination.
Use the card on a terminated CAN bus.
3.3.2
Example of a Connection
Figure 6: Simple CAN connection
In this example, the PCAN-PCI Express card is connected with a control unit by a cable that is terminated at both ends.
14
PCAN-PCI Express – User Manual
3.3.3
Maximum Bus Length
High-speed CAN networks may have bit rates of up to 1 Mbit/s. The maximum bus length depends primarily on the bit rate.
The following table shows the maximum possible CAN bus length at different bit rates:
Bit rate
1 Mbit/s
500 kbit/s
250 kbit/s
125 kbit/s
50 kbit/s
20 kbit/s
10 kbit/s
5 kbit/s
Bus length
40 m
110 m
240 m
500 m
1.3 km
3.3 km
6.6 km
13.0 km
The listed values have been calculated on the basis of an idealized system and can differ from reality.
15
PCAN-PCI Express – User Manual
4
Using the Software
This chapter covers the provided software PCAN-View and the programming interface PCAN-Basic.
4.1
CAN Monitor PCAN-View for Windows
PCAN-View for Windows is a simple CAN monitor for viewing, transmitting, and logging CAN messages.
Figure 7: PCAN-View for Windows
Do the following to start and initialize PCAN-View:
1. If PCAN-View is already installed on the hard disk, open the
Windows Start menu, go to Programs > PCAN-Hardware, and select the entry PCAN-View.
16
PCAN-PCI Express – User Manual
If you haven’t installed PCAN-View together with the device driver, you can start the program directly from the supplied
DVD. In the navigation program (Intro.exe), go to English
> Tools, and under PCAN-View for Windows select the link
Start.
The dialog box for selecting the CAN hardware and for setting the CAN parameters appears.
Figure 8: Selection of the CAN hardware and parameters
2. From the list Available CAN hardware select the CAN channel to be used.
3. Select the bit rate that is used by all nodes on the CAN bus from the dropdown list Bit rate.
4. Under Filter settings you can limit the range of CAN IDs to be received, either for standard frames (11-bit IDs) or for extended frames (29-bit IDs).
5. Finally confirm the settings in the dialog box with OK. The
main window of PCAN-View appears (see Figure 9).
17
PCAN-PCI Express – User Manual
4.1.1
Receive/Transmit Tab
Figure 9: Receive/Transmit Tab
The Receive/Transmit tab is the main element of PCAN-View. It contains two lists, one for received messages and one for the transmit messages. Representation of CAN data is in hexadecimal format.
Do the following to transmit a CAN message with PCAN-View:
1. Select the menu command Transmit > New Message
(alternatively or Ins).
The dialog box New Transmit Message is shown.
18
PCAN-PCI Express – User Manual
Figure 10: Dialog box New transmit message
2. Enter the ID and the data for the new CAN message.
3. The field Cycle Time indicates if the message shall be transmitted manually or periodically. If you want to transmit the message periodically, you must enter a value greater than 0. For a manual-only transmission enter 0.
4. Confirm the entries with OK.
The created transmit message appears on the
Receive/Transmit tab.
5. You trigger selected transmit messages manually with the menu command Transmit > Send (alternatively Space bar).
The manual transmission for CAN messages being transmitted periodically is carried out additionally.
Tip: Using the menu command File > Save the current transmit messages can be saved to a list and loaded for reuse later on.
19
PCAN-PCI Express – User Manual
4.1.2
Trace Tab
Figure 11: Trace Tab
On the Trace tab the data tracer of PCAN-View is used for logging the communication on a CAN bus. During this process the CAN messages are cached in the working memory of the PC. Afterwards they can be saved to a file.
The tracer can be configured to run in linear or in ring buffer mode.
In linear buffer mode the logging is stopped as soon as the buffer is filled completely. In ring buffer mode the oldest messages are overwritten by incoming ones.
20
PCAN-PCI Express – User Manual
4.1.3
Status Bar
Figure 12: Display of the Status Bar
The status bar shows information about the current CAN connection, about error counters (Overruns, QXmtFull) and shows error messages.
You can find further information about the use of PCAN-View in the help which you can invoke in the program via the menu Help or the
F1 key.
21
PCAN-PCI Express – User Manual
4.2
Linking Own Programs with PCAN-Basic
Figure 13: PCAN-Basic
On the provided DVD you can find files of the programming interface PCAN-Basic in the directory branch Develop. This API provides basic functions for linking own programs to CAN interfaces by PEAK-System and can be used for the following operating systems:
Windows 8, 7, Vista (32/64-bit)
Windows CE 6.x (x86/ARMv4)
Linux (32/64-bit)
The API is designed for cross-platform use. Therefore software projects can easily ported between platforms with low efforts.
PEAK-System has created examples for the following programming languages: C++, C#, C++/CLR, Visual Basic, Delphi, Python, and
Java.
22
PCAN-PCI Express – User Manual
4.2.1
Features of PCAN-Basic
Supports Windows 8, 7, Vista (32/64-bit), Windows CE 6.x, and
Linux (32/64-bit) operating system
Multiple PEAK-System applications and your own can be operated on a physical CAN channel at the same time
Use of a single DLL for all supported hardware types
Use of up to 8 channels for each hardware unit (depending on the PEAK CAN interface used)
Simple switching between channels of a PEAK CAN interface
Driver-internal buffer for 32,768 messages per CAN channel
Precision of time stamps on received messages up to 1 μs
(depending on the PEAK CAN interface used)
Access to specific hardware parameters, such as listen-only mode
Notification of the application through Windows events when a message is received
Extended system for debugging operations
Multilingual debugging output
Output language depends on operating system
Debugging information can be defined individually
An overview of the API functions is located in the header files. You can find detailed information about the PCAN-Basic API on the provided DVD in the text and help files (file name extensions .txt and .chm).
23
PCAN-PCI Express – User Manual
4.2.2
Principle Description of the API
The PCAN-Basic API is the interface between the user application and device driver. In Windows operating systems this is a DLL
(Dynamic Link Library).
The sequence of accessing the CAN interface is divided into three phases:
1. Initialization
2. Interaction
3. Completion
Initialization
A CAN channel must be initialized before using it. This is done by the simple call of the function CAN_Initialize. Depending on the type of the CAN hardware, up to eight CAN channels can be opened at the same time. After a successful initialization the CAN channel is ready for communication with the CAN hardware and the CAN bus.
No further configuration steps are required.
Interaction
For receiving and transmitting CAN messages the functions
CAN_Read and CAN_Write are available. Additional settings can be made, e.g. setting up message filters to confine to specific CAN IDs or setting the CAN controller to listen-only mode.
When receiving CAN messages, events are used for an automatic notification of an application (client). This offers the following advantages:
The application no longer needs to check for received messages periodically (no polling).
The response time at reception is reduced.
24
PCAN-PCI Express – User Manual
Completion
To end the communication the function CAN_Uninitialize is called in order to release the reserved resources for the CAN channel, among others. In addition the CAN channel is marked as
"Free" and is available to other applications.
4.2.3
Notes about the License
Device drivers, the interface DLL, and further files needed for linking are property of the PEAK-System Technik GmbH and may be used only in connection with a hardware component purchased from
PEAK-System or one of its partners. If a CAN hardware component of third-party suppliers should be compatible to one of PEAK-
System, then you are not allowed to use or to pass on the driver software of PEAK-System.
If a third-party supplier develops software based on the PCAN-Basic and problems occur during the use of this software, consult the software provider.
25
PCAN-PCI Express – User Manual
5
Technical Specifications
Connectors
Computer
CAN
CAN
Specification
Bit rates
Controller
PCI Express x1 (1 Lane), Specification 1.1
D-Sub (m), 9 pins
Pin assignment according to specification CiA® 102
ISO 11898-2, High-speed CAN
2.0A (standard format) and 2.0B (extended format)
5 kbit/s - 1 Mbit/s
FPGA implementation (SJA1000 compatible)
Galvanic isolation
Supplying external devices up to 500 V, separate for each CAN channel
D-Sub pin 1; 5 V, max. 50 mA not assigned at delivery
Termination none
Measures
Size
Weight
PCB: 121 x 114 mm (H x W)
See also dimension drawing in Appendix B on page 29
PCAN-PCI Express Single Channel:
PCAN-PCI Express Dual Channel:
PCAN-PCI Express Four Channel:
55 g
66 g
73 g
Power supply
Current consumption
Product version
Single Channel:
Dual Channel:
Four Channel: at 3.3-V pin at 12-V pin
265 mA
265 mA
300 mA max. 50 mA max. 80 mA max. 150 mA
Continued on the next page
26
PCAN-PCI Express – User Manual
Environment
Operating temperature -40 - +85 °C
-40 - +125 °C Temperature for storage and transport
Relative humidity 15 - 90 %, not condensing
EN 55022:2011-12
EC directive 2004/108/EG
27
PCAN-PCI Express – User Manual
Appendix A
CE Certificate
28
PCAN-PCI Express – User Manual
Appendix B
Dimension Drawing
Figure 14: Dimension drawing PCAN-PCI Express
The figure does not show the actual size of the product.
29
PCAN-PCI Express – User Manual
Appendix C
Quick Reference
Software/Hardware Installation under Windows
Before installing the PCAN-PCI Express card into the computer set up the corresponding software package from the supplied DVD
(with administrator privileges). Afterwards, insert the PCIe card into a vacant PCI Express slot of the switched off computer. The PCIe card is recognized by Windows and the driver is initialized. After the installation process is finished successfully you can find the entry
“PCAN-PCI Express” in the branch “CAN-Hardware” of the
Windows Device Manager.
Getting Started under Windows
Run the CAN monitor PCAN-View from the Windows Start menu as a sample application for accessing the PCAN-PCI Express card. For initialization of the PCIe card select the desired CAN channel and the
CAN bit rate.
High-speed CAN connector (D-Sub, 9 pins)
30
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement