Operating Instructions - Electronics Design Group

Operating Instructions - Electronics Design Group
Translation of the original instructions
PT 0250 BEN/E (1209)
DCU 002, 110, 180, 310, 400
Display and control unit
Operating Instructions
EN
Table of contents
Table of contents
1
About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Validity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Improper use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
5
6
3
Product description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 Product identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 General connection description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4 Range of application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
7
8
8
4
Connections diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 Connecting to the mains power supply . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
10
11
6
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1 LC-Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 Symbol description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3 Button functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4 Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6 Operation with DCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.7 Pressure measurement via DCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.8 Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
12
13
13
14
14
15
15
16
7
Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.1 Operating mode display via LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.2 Error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
10
Technical data and dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
10 Technical data and dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
10.2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2
About this manual
1
About this manual
1.1
Validity
This operating manual is for customers of Pfeiffer Vacuum. It describes the functioning
of the designated product and provides the most important information for safe use of
the unit. The description follows applicable EU guidelines. All information provided in this
operating manual refer to the current state of the product's development. The documentation remains valid as long as the customer does not make any changes to the product.
Up-to-date operating instructions can also be downloaded from www.pfeiffer-vacuum.com.
1.2
Conventions
Safety instructions
The safety instructions in Pfeiffer Vacuum operating instructions are the result of risk
evaluations and hazard analyses and are oriented on international certification standards as specified by UL, CSA, ANSI Z-535, SEMI S1, ISO 3864 and DIN 4844. In this
document, the following hazard levels and information are considered:
DANGER
Imminent danger
Indicates an imminent hazardous situation that will result in death or serious injury.
WARNING
Possibly imminent danger
Indicates an imminent hazardous situation that can result in death or serious injury.
CAUTION
Possibly imminent danger
Indicates an imminent hazardous situation that can result in minor or moderate injury.
NOTICE
Command or note
Command to perform an action or information about properties, the disregarding of
which may result in damage to the product.
3
About this manual
Pictograph
definitions
Prohibition of an action or activity in connection with a source of danger,
the disregarding of which may result in serious accidents
Warning of a displayed source of danger in connection with operation of
the unit or equipment
Command to perform an action or task associated with a source of danger, the disregarding of which may result in serious accidents
Important information about the product or this document
Instructions in the
text
 Work instruction: here you have to do something.
Abbreviations used
DCU:
Display and control unit
TC:
Electronic drive unit for turbopump
TPS:
Mains pack
[P:000]:
Parameter of the electronic drive unit with number
4
Safety
2
Safety
2.1
Safety precautions
Duty to inform
Each person involved in the installation or operation of the unit must read and observe
the safety-related parts of these operating instuctions.
 The operator is obligated to make operating personnel aware of dangers originating
from the unit or the entire system.
WARNING
Danger of unsafe electrical installation
Safe operation after installation is the responsibility of the operator.
 Do not independently modify or change the pump and electrical equipment.
 Make sure that the system is integrated in an emergency off safety circuit.
 Consult Pfeiffer Vacuum for special requirements.
WARNING
Danger of electric shock
In case of defect, the parts connected to the mains supply are under voltage.
 Always keep the mains connection freely accessible so you can disconnect it at any
time.
●
●
●
●
●
Observe the safety and accident prevention regulations.
Check regularly that all safety precautions are being complied with.
Do not loosen any plug connection during operations.
Keep leads and cables well away from hot surfaces (> 70 °C).
Always ensure a safe connection to the protective earthing conductor (PE, protection
class I).
● The unit has been accredited with protection class IP 20. Take necessary measures
when installing into ambient conditions, which afford other protection classes.
● Before carrying out any work disconnect the unit and all associated installations safely
from the mains.
2.2
Proper use
NOTICE
CE conformity
The manufacturer's declaration of conformity becomes invalid if the operator modifies
the original product or installs additional components.
 Following installation into a plant and before commissioning, the operator must check
the entire system for compliance with the valid EU directives and reassess it accordingly.
● The DCU is a display and control unit and may only be used to control Pfeiffer Vacuum
Turbopumps with electronic drive unit and associated peripheral devices.
● The DCU with integrated powerpack is also used to supply power to the turbopump.
5
Safety
2.3
Improper use
Improper use will cause all claims for liability and warranties to be forfeited. Improper use
is defined as usage for purposes deviating from those mentioned above, especially:
● connection to pumps or units which are not suitable for this purpose according to their
operating instructions
● connection to units which have exposed voltage-carrying parts
● connection to mains supplies, which do not confirm to the regulations IEC 61010 or
IEC 60950
● operation of the devices in areas with ionizing radiation
6
Product description
3
Product description
3.1
Product identification
Product features
The DCU is a display and control unit for Pfeiffer Vacuum Turbopumps with integrated
electronic drive unit. It enables control of all essential parameters for the electronic drive
unit. It is also possible to connect a pressure gauge.
Characteristics
DCU 002
DCU 110
DCU 180
DCU 310
DCU 400
Mains supply
Power consumption
Suitable for HiPace
Electronic drive unit
none
5 VA
all
TC 110
TC 400
TM 700
TC 1200
integrated
130 VA
10, 60, 80
TC 110
integrated
210 VA
300
TC 110
integrated
340 VA
300, 400, 700, 800
TC 400 (24 V DC)
integrated
450 VA
300, 400, 700, 800
TC 400 (48 V DC)
TM 700
To correctly identify the product when communicating with Pfeiffer Vacuum, always have
the information from the rating plate available.
D-35614 Asslar
HiPace 300
DN 100 ISO-K, 3P
M.-No.: PM P03 900
Mod.:
Ser. -No.:
--Oil:
S(N2): 260 l/s
60000
1/min, 1000 Hz
n,f:
Weight: 6.7 kg
Made in Germany
Fig. 1:
Scope of delivery
3.2
●
●
●
●
Example for a rating plate
Display and control unit DCU
Interface cable M12 to M12, length 3 m
Fixing materials
Operating instructions
Function
DCU
1
2
3
4
Fig. 2:
1
2
Front cover DCU
LC display, illuminated
Status symbols
3
4
LED "Operating display"
Operating keys
7
Product description
3.3
General connection description
PE
S1
X3
X3
AC in
RS485
RS485
DC out
c
c
DCU 110 / 180 / 310 / 400
Fig. 3:
Display and control unit DCU, rear view variants
S1
Mains switch
AC in Mains connection, input
DC out Mains connection, output
3.4
DCU 002
PE
X3
RS485
C
Protective earth connection (M4)
Pressure gauge connection
Serial interface
Contrast adjustment
Range of application
Pfeiffer Vacuum display and control units DCU should be installed and operated under
the following ambient conditions.
Installation location
Permissible protection class
Protection class
Temperature
Relative air humidity
Air pressure:
8
weatherproof (internal space)
IP 20
I
+5 °C to +50 °C
max. 80%, at T ≤ 31°C, max. 50% at T ≤ 40°C
75 kPa - 106 kPa
Connections diagram
4
Connections diagram
AC in
L1
N
PE
S1
DCU 110
DCU 180
DCU 310
DCU 400
Fig. 4:
DC out
B
B
C
C
A
A
DC in
A
+1
-2
B
FE
C
RS485
1
2
3
4
5
RS485
X3
1
2
3
4
5
6
1
5
2
3
6
4
Terminal diagram and layout for DCU, variants with integrated power pack
1
2
3
4
5
DCU 002
Fig. 5:
1
5
2
3
6
4
1
2
3
4
5
6
1
2
3
4
5
RS485
X3
1
2
3
4
5
6
RS485
1
2
3
4
5
6
1
5
2
3
6
4
1
2
3
4
5
1
5
2
3
6
4
Terminal diagram and layout for DCU 002
Connection to:
Turbopump with electronic drive unit:
Gauge type:
DCU 002
DCU 110/180/310/400
TC 110*
TC 400
TM 700
TC 1200
TPR 2xx
PKR 2xx
APR 250/260
CMR 3xx
PCR 280
TC 110*
TC 400
TM 700
TPR 2xx
PKR 2xx
APR 250/260
CMR 3xx
PCR 280
Connections on electronic drive unit TC 110
Different connection possibilities (not provided in the scope of supply) are dependent on
the type of electronic drive unit TC 110.
● Connection via connecting cable or adapter
● Connection for electronic drive unit "TC 110 RS" direct to the RS485 interface (power
supply separately via TCP or connecting cable)
● For more information visit http://www.pfeiffer-vacuum.com, Keyword "HiPace accessories"
9
Installation
5
Installation
5.1
Assembly
NOTICE
Ensure free convection
Incorrect installation can cause damage by over-heating or create a fire hazard.
 Maintain a minimum distance of 50 mm from cooling vents to adjacent components
or boundaries.
 Install device perpendiculary.
Install in a rack as a
19" module
5.2
The DCU is fitted in a casing that is suitable for installing in 19"/3HE rack modules.
 Insert the DCU in the guiderails of a 19"/3HE rack and screw on the front panel securely with four fixing screws provided as part of the scope of supply.
Connecting to the mains power supply
This only applies to DCUs with integrated power packs. The DCU 002 receives the
operating voltage via the "RS485" interface for the turbopump electronic drive
unit.
WARNING
Danger of unsafe electrical installation
Safe operation after installation is the responsibility of the operator.
 Do not independently modify or change the pump and electrical equipment.
 Make sure that the system is integrated in an emergency off safety circuit.
 Consult Pfeiffer Vacuum for special requirements.
WARNING
Danger of electric shock
In case of defect, the parts connected to the mains supply are under voltage.
 Always keep the mains connection freely accessible so you can disconnect it at any
time.
 Order the mains cable separately (see "accessories").
 Switch off switch S1 on the power pack (position "0").
 Plug mains cable into the mains connection "AC in".
 Lock the mains cable with the mounting bracket.
 Connect the mains cable to the mains.
 Always ensure a safe connection to the protective earthing conductor (PE, protection
class I).
10
Installation
5.3
Connections
 Connect interface cable (supplied) on "RS485" to DCU and electronic drive unit.
 Make connection between "DC out" on DCU and "DC in" on electronic drive unit in accordance with the terminal diagram or with a connecting cable from the Pfeiffer Vacuum accessories.
 Connect pressure gauge if required to "X3" on the DCU.
● The RS485 serial interface is used exclusively to control the electronic drive unit on
the vacuum pump. See the Operating Instructions for the respective electronic drive
unit for the interface protocol specification.
Note the operating priority of the interfaces for the electronic drive unit!
DIL switches in the connecting cable or bridges in the mating connector for the D-Sub
connector for the electronic drive unit enable operation of the pump without control unit.
This may cause priority conflicts with the RS485 interface.
 Disconnect the mating connector from the "remote" terminal prior to connecting a
DCU to electronic drive units TC 400, TC 1200 or TM 700.
 Switch off the supreme operating control (DIL switch S1/S2 = OFF) prior to connecting a DCU to the electronic drive unit TC 110.
HiPace 80
DCU 002
TC 110
X3
RS 485
TPS
PM 061 299 -X
Fig. 6:
Example: Connection of DCU 002 toTurbopump HiPace 80 using connecting cable
HiPace 700
DCU
TC 400
X3
PM 061 299 -X
RS 485
DC out
Fig. 7:
Example: Connection of DCU with integrated power pack to Turbopump HiPace 700
11
Operation
6
Operation
6.1
LC-Display
721: Venting time
--->
3600 s
795
1
2
3
4
5
The four line LCD visualizes the functions of theDCU.
Functions are assigned as follows:
– Line 1: Number and name of the selected parameter (e.g. 721: Vent time).
– Line 2: relevant value for the selected parameter. The arrow –––► indicates Edit
mode.
– Line 3 with two functions:
– Function 1: Current messages concerning operation and control will be displayed
(See operating instructions for electronic drive unit and 7.2 Error codes).
– Function 2: presentation of a required second parameter in the format [Parameter
number: value]. The function for this line can be set via parameter [P:795] Servicelin in Line 1. All parameters can be accessed with "Servicelin". Error messages
will be displayed independently of the selected function.
– Line 4: presentation of the current equipment status by arrows that point to the associated symbols.
– Line 5: Symbols (see below)
12
Operation
6.2
Symbol description
Symbol
Description
Arrow Explanation
Pump accelerates
= [P:307]
-
NO
YES
Preselection heating
= [P:001]
-
No preselection
Preselection heating, switching point not reached
Heating On, switching point reached
Standby
= [P:002]
-
OFF
ON
Equipment remote controlled
= [P:300]
-
NO
YES
Switching point reached
= [P:302]
-
NO
YES
Excess temperature
-
No excess temperatures
Excess temperature turbopump = [P:305]
Excess temperature turbo-electronics = [P:304]
Excess temperature turbopump and turbo-electronics
Final speed reached
= [P:306]
6.3
-
NO
YES
Button functions
Four short-travel keys (Softkeys) constitute the operator interface for the DCU.
Key
Application/Example
Explanation
Reset (error acknowledgement) acknowledges errors (red
LED illuminates)
[309]: ActualSpd
[308]: SetRotSpd
Scroll back through parmeters
Scrolls back one parameter
[310]: DrvCurrent
[311]: OpHrsPump
Scroll forwards through parameters
Scrolls forwards one parameter
[001]: Heating
–––► off
Change value (Edit mode)
Access to displayed value, if possible
(Arrow–––► is displayed)
Confirm value (Parameter selection mode)
Accept changed value
("change confirmed" is displayed)
Pumping station ON/OFF
switches pumping station on or off.
corresponds to parameter [010]: "PumpgStatn"
Simultaneous
[001]: Heating
on
[010]: PumpgStatn
on / off
13
Operation
6.4
Switching on
Ensure correct connection in the absence of display!
All connecting cables must always be connected to the electronic drive unit and the
mains at DCU with integrated power supplies. Otherwise the correct functioning of the
unit is not possible; there will be no operating display.
 Connect all connecting cables for "RS485", "DCout" and "ACin".
 Switch on the supply voltage with switch S1 on the DCU with integrated power pack,
or when using a DCU 002 switch on via the provided power pack (e.g. TPS).
Self-test
The DCU carries out a self-test and a check of the connected units after switch-on. The
duration of the self-test is approx. 20s and is visualized in the display with a progress bar.
●
●
●
●
●
●
●
●
LC display test: All characters in the LC display go dark for a short time.
LED test: The red and green LEDs illuminate during the self-test.
Hardware test of the DCU
Pump electronics connection test: The correct pump electronics connection and identity will be checked.
Parameter check: Information on operating parameters will be loaded.
Identification of the connected units: Electronic drive unit designation display. Pressure gauge designation display.
– The "TPR" indication will appear in the display when a PCR 280 pressure gauge is
connected.
If no error has occurred, it is DCU ready to operate.
The green LED flashes.
 Reset malfunction messages using key
6.5
, if necessary.
Operation
All function-relevant variables of a turbopump are anchored in the electronic drive unit as
parameters. Each parameter has a three-digit number and a designation. Parameters
can be used via Pfeiffer Vacuum display and control units or via RS-485 with the Pfeiffer
Vacuum protocol.
The value of a parameter is always readable. Editable parameters are adjustment commands and target values (See the operating instructions for the respective electronic
drive unit for this purpose).
Selecting the parameters
 Preselect parameter number using the
(backwards) or
(forwards) keys.
– Fast scrolling by pressing and keeping the relevant key depressed.
● The selected parameter appears in line 1, the corresponding value in line 2.
Set parameters
 Select a parameter.
 Simultaneously press keys
and
.
● The edit mode for the selected parameter is active.
● At the beginning of the second line an arrow ( –––►) appears.
 Using keys
tions.
,
to decrease or increase the value, respective to change op-
 Simultaneously press keys
and
.
● If line 3 = empty (see P:795), the following will be displayed: "change confirmed"
● The parameter is set.
● Edit mode for the parameter is ended. The arrow ( –––►) disappears.
14
Operation
Edit mode( –––►) will disappear again automatically under the following conditions and without accepting the value to be changed:
●
●
●
●
6.6
Input disruption or no key operation for more than 10s.
If an error occurs.
Key 6 "Pumping station ON/OFF" has been pressed.
If line 3 = empty , "data not changed" will be displayed.
Operation with DCU
Parameter set and Pfeiffer Vacuum display and control unit
Pfeiffer Vacuum display and control units DCU show the basic parameter set by default.
Furthermore the DCU contains parameters, which are not positioned in the electronic
drive unit.
 Parameter [P:794] = 1 (Display of all available parameters).
Designation
340
350
351
738
794
Pressure
Ctr Name
Ctr Software
Gaugetype
Param set
Active pressure value
Type of display and control unit
Software of display and control unit
Type of pressure gauge
Parameterset
795 Servicelin
Functions
0 = basic parameter set
1 = extended parameter set
Insert service line
Unit
Access
Display
Data type
#
7
4
4
4
7
R mbar
R
R
RW
RW
7
RW
min
max
default 
1E-10 1E3
0
1
0
795
The display of further parameters depends on the type of electronic drive unit.
Start pump by pressing "Pumping station ON/OFF" key on the DCU
The "Pumping station" key only controls the parameter [P:010]. All components connected via the electronic drive unit will be activated or deactivated according to their configuration.
 Ensure that the parameter [P:023] is also switched on for powering-up the turbopump.
6.7
Pressure measurement via DCU
Connection and use of a high vacuum gauge enables pressure measurement in the vacuum system via the DCU.
Pressure measurement with the DCU
An exact pressure measurement is not possible with the DCU. This is particularly true
with linear gauges in the lower pressure range.
 Use suitable measuring instrument.
Displaying the gauge
type
 Parameter [P:794] = 1 (Displaying the extended parameter set at the DCU)
 Select or enter parameter [P:738] Gaugetype.
Gauges with identical surge impedance are only recognized by DCU as a group (e.g.
CMR?). Manual input of the exact gauge type is also possible via the parameter [P:738].
Displaying the active
pressure value
Display example
Meaning
TPR 280
CMR ?
none
Gauge TPR 280 connected
Gauge of the CMR Group connected, exact type not yet set
No pressure gauge connected
 Parameter [P:794] = 1 (Displaying the extended parameter set at the DCU)
 Select parameter [P:340] Pressure.
15
Operation
Display example
Meaning
–––––– mbar
< 5E-4mbar
No pressure gauge connected
Measuring range not reached (dependent on the pressure
gauge used)
Measuring range exceeded (dependent on the pressure gauge
used)
Valid pressure measurement
Gauge type not yet identified; see [P:340]
Error in pressure gauge
> 1E3mbar
6.3E-9mbar
id fam mbar
Error
6.8
Switching off
 Press key
on the DCU front panel.
 Cut of supply voltage with switch S1 on the DCU with integrated power pack, or when
using a DCU 002 via the supplied power pack (e.g. TPS).
16
Malfunctions
7
Malfunctions
Ensure correct connection in the absence of display!
All connecting cables must always be connected to the electronic drive unit and the
mains at DCU with integrated power supplies. Otherwise the correct functioning of the
unit is not possible; there will be no operating display.
 Connect all connecting cables for "RS485", "DCout" and "ACin".
7.1
Operating mode display via LED
The red LED (error status) and green LED (operating status) on the front panel can accept the following states:
LED Symbol Permanent Off
7.2
Flashing
Flashing
(1/12 s active)
(1/2 s active)
Gree
n
No adequate power Pumping station
supply
"OFF"
Red
No error
Power failure
Warning
Permanent On
Pumping station
"ON"
Errors
Error codes
Errors (** Error –––– **) always cause the connected peripheral devices to be switched
off.
 Eliminate error and reset by pressing keys
.
Warnings (* Warning –––– *) are only displayed and do not cause components to be
switched off.
Error code
Problem
Remedy
* Warning F110 *
– Pressure gauge faulty
– Pressure gauge removed during operation
** Error E040 **
** Error E042 **
** Error E043 **
** Error E090 **
Hardware error: external RAM faulty
Hardware error: EPROM check total
Hardware error: E2PROM write error
– RAM not large enough
– DCU is connected to incorrect pump electronics
The connected electronic drive unit does not respond
 Restart with gauge connected
 Change pressure gauge
 Install pressure gauge correctly
 Contact Pfeiffer Vacuum Service.
 Contact Pfeiffer Vacuum Service.
 Contact Pfeiffer Vacuum Service.
 Contact Pfeiffer Vacuum Service.
 Connect correct pump electronics
 Contact Pfeiffer Vacuum Service.
** Error E698 **
Further error and warning messages are described in the Operating Instructions for the
electronic drive unit.
17
Service
8
Service
Pfeiffer Vacuum offers first-class service!
● Fast replacement with exchange products in mint condition
● Advice on the most cost-efficient and quickest solution
Detailed information, addresses and forms at: www.pfeiffer-vacuum.com (Service).
Service orders
All service orders are carried out exclusively according to our repair conditions for vacuum units and components.
9
18
Accessories
An overview about original Pfeiffer Vacuum accessories for the designated device can
be found in the operating instructions of the respective vacuum pump.
Technical data and dimensions
10 Technical data and dimensions
10.1 Technical data
Parameter
DCU 002
Connection
Ambient temperature
Protection category
Power consumption
Weight
12-30 V DC
5-50 °C
IP 20
5 VA
0.4 kg
Parameter
DCU 110
DCU 180
Ambient temperature
Protection category
Mains requirement: frequency (range)
Mains requirement: power consumption
Mains requirement: voltage (range)
Output voltage
Output current
Weight
5-50 °C
IP 20
50/60 Hz
130 VA
5-50 °C
IP 20
50/60 Hz
210 VA
115-230 (-20-+15 %) V AC
24 (± 2 %) V DC
4.6 A
1.2 kg
115-230 (-20-+15 %) V AC
24 (± 2 %) V DC
7.5 A
1.7 kg
Parameter
DCU 310
DCU 400
Ambient temperature
Protection category
Mains requirement: frequency (range)
Mains requirement: power consumption
Mains requirement: voltage (range)
Output voltage
Output current
Weight
5-50 °C
IP 20
50/60 Hz
340 VA
115-230 (-20-+15 %) V AC
24 (± 2 %) V DC
12.5 A
1.85 kg
5-50 °C
IP 20
50/60 Hz
450 VA
115-230 (-20-+15 %) V AC
48 (± 2 %) V DC
8.4 A
2.3 kg
19
Technical data and dimensions
10.2 Dimensions
122.5
111.2
38.9
3.5
128.5 (3HE)
35.6
106.7 (21TE)
91.5
64.4
6
105.5
B
2.4
20
Dimension
DCU 002
DCU 110
DCU 180
DCU 310
DCU 400
B
52.5 mm
200.0 mm
230.0 mm
230.0 mm
230.0 mm
Declaration of conformity
according to the EC directive:
● Electromagnetic Compatibility 2004/108/EC
● Low Voltage 2006/95/EEC
We hereby certify, that the product specified below is in accordance with the provision
of EU Electromagnetic Compatibility Directive 2004/108/EEC and EU Low Voltage Directive 2006/95/EEC.
DCU
DCU 002, 110, 180, 310, 400
Guidelines, harmonised standards and national standards and specifications which
have been applied:
DIN EN 61000-3-2 : 2008
DIN EN 61000-3-3 : 2006
DIN EN 61010-1 : 2002
DIN EN 61326-1 : 2006
DIN EN 62061 : 2005
Semi F47-0200
Semi S2-0706
Signatures:
Pfeiffer Vacuum GmbH
Berliner Straße 43
35614 Asslar
Germany
(M.Bender)
Managing Director
(Dr. M. Wiemer)
Managing Director
CE/2011
Vacuum solutions
from a single source
Pfeiffer Vacuum stands for innovative and custom
vacuum solutions worldwide, technological perfection,
competent advice and reliable service.
Complete range
of products
From a single component to complex systems:
We are the only supplier of vacuum technology
that provides a complete product portfolio.
Competence in
theory and practice
Are you looking for a
perfect vacuum solution?
Please contact us
Benefit from our know-how and our portfolio of training
opportunities! We can support you with your plant layout
and provide first-class on-site-service worldwide.
Pfeiffer Vacuum GmbH
Headquarters • Germany
T +49 6441 802-0
[email protected]
www.pfeiffer-vacuum.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement