Operating instructions OSRAM Sensor Touch DIM LS LI Light sensor

Operating instructions OSRAM Sensor Touch DIM LS LI Light sensor
Description
Purpose and application
The TOUCH DIM LS LI sensor regulates the brightness at the
workplace and in office areas to increase the working comfort
and to save energy.
TOUCH DIM LS LI
The sensor can be installed in luminaires (e.g. floor standing
luminaires) or in false ceilings.
Function
A
The sensor measures the brightness in the area to be regulated
and keeps this to an adjustable set value by introducing artificial
light according to the amount of daylight available.
B
As the amount of daylight increases, artificial lighting is
reduced.
Design
The sensor is made up of the following components:
• Light sensor (A)
• Housing (B)
• Connections (C) for signal line, neutral conductor and phase
Light sensor
Operating instructions
C
Operation
Symbols
Pushbutton on
the luminaire
Luminaire on
Switch on
Luminaire off
Switch off
Luminaire
flashes
Short press
(< 0.5 s)
Brightness with
automat. control
Long press
(0.5 – 4 s)
Confirmation of
the setting
Double-click
Manual dimming
2x
< 30 s
1
2
3
Switching luminaire on and off
2x
< 30 s
1
2
Via short press.
3
Note: The luminaire is first switched on with minimum brightness. If a setpoint is predefined for brightness control, the
brightness is controlled automatically.
A
max
1
2
3
...
B
A
Changing the brightness manually
max
1
2
> 30 s
1
2
Via long press.
3
...
B
3
Note: The brightness control is deactivated until the next time
the luminaire is switched on.
Each repeated long key button press causes a toggle between
increased brightness and decreased brightness.
1
> 30 s
2
3
Specifying set value for brightness control
Specifying the set value activates the brightness control.
Set the desired brightness.
‚Double-click
ƒConfirmation: luminaire flashes.
2x
1
< 30 s
2
3
1
< 30 s
2
3
VI 2010
TouchDIM-LS-LI_ba1006en_we1.02.indd
OSRAM GmbH
Kunden Service Center
Customer-Service-Center (CSC)
2x
A
max
Steinerne Furt 62
86167 Augsburg
Germany
1
Tel : +49 (0) 1803 677 - 200
(kostenpflichtig / charges apply)
Fax.: +49 (0) 1803 677 - 202
www.osram.com
2
3
max
1
2
Deactivating brightness control
Switch off if necessary.
‚Double-click
ƒConfirmation: maximum brightness.
A
B
...
B
...
3
www.osram.de
40083210230250
1
> 30 s
2
3
1
> 30 s
2
3
4008321023025
Page 1 of 2
Troubleshooting
Operation (cont.)
If you cannot remedy the fault, please contact the Customer
Service department of the luminaire manufacturer.
Luminaire does not function
No mains voltage.
à Use a voltage tester to check for mains voltage.
Illuminant is faulty.
à Replace the illuminant.
The luminaire was switched off via the pushbutton.
à Switch on the luminaire.
The sensor is exposed to excessive amounts of ambient light.
à Hold the sensor closed and observe the behaviour of the
luminaire.
Brightness is not adjusted to the selected set value
The pushbutton was not pressed within 30 seconds after the
setpoint was adjusted
à Double-click within 30 seconds after dimming manually.
Brightness control was not started until 5 seconds after the
setpoint was adjusted.
à Wait for the delay period to elapse.
Brightness control was deactivated by a manual operation.
à Switch the luminaire off and on again.
No setpoint was saved.
à Save a new setpoint.
Luminaire does not react as expected to the press of a
button
The pushbutton was pressed too long or too short.
à See Changing the brightness manually.
Appendix
The EMC requirements to EN 61547 are fulfilled.
Conformity with the relevant EU directives is
confirmed by the CE symbol.
Page 2 of 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement