User Guide
IM-5S-ELC
IM-5W-ELC
IM-5S-HID
IM-5W-HID
User Guide
Innovation , Quality , Performance
23J
Professional Entertainment Technology
IM-5S-ELC
IM-5W-ELC
IM-5S-HID
IM-5W-HID
User Guide
Innovation , Quality , Performance
23J
Professional Entertainment Technology
1J
22J
1J
22J
Technical Specifications
Power
AC 120V~60Hz
AC 230/240/250V~50/60Hz
Fuse
20mm Glass T6.3A
20mm Glass T5A
Lamp
TABLE OF CONTENTS
1. Safety Instruction
HID 150W
2. Technical Specification
ELC 24V 250W
Dimension
290 x 330 x 380 mm
Weight
12 kg
2.1 Beam Angle
3. Lamp
4. How To Set The Unit
4.1 Control Panel
4.2 Main Function
5. How To Control The Unit
5.1
5.2
5.3
5.4
5.5
Master/Slave Built-In Preprogrammed Function.
Easy Controller
iSolution Operation / Universal DMX Controller
DMX 512 Configuration
DMX 512 Connection
6. Troubleshooting
7. Maintenance and Cleaning
21J
2J
Technical Specifications
Power
AC 120V~60Hz
AC 230/240/250V~50/60Hz
Fuse
20mm Glass T6.3A
20mm Glass T5A
Lamp
TABLE OF CONTENTS
1. Safety Instruction
HID 150W
2. Technical Specification
ELC 24V 250W
Dimension
290 x 330 x 380 mm
Weight
12 kg
2.1 Beam Angle
3. Lamp
4. How To Set The Unit
4.1 Control Panel
4.2 Main Function
5. How To Control The Unit
5.1
5.2
5.3
5.4
5.5
Master/Slave Built-In Preprogrammed Function.
Easy Controller
iSolution Operation / Universal DMX Controller
DMX 512 Configuration
DMX 512 Connection
6. Troubleshooting
7. Maintenance and Cleaning
21J
2J
1.Safety Instruction
Please read carefully the instruction, which includes important information
WARNING
about the installation, usage and maintenance.
y Please keep this User Guide for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction booklet.
EC Declaration of Conformity
y Unpack and check carefully there is no transportation damage before using the unit.
y Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
We declare that our products (lighting equipments) comply with the
following specification and bears CE mark in accordance with the
y The unit is designed for use with the HID 150W or ELC 24V 250W (two version). Do not
use any other type of lamp.
provision of the Electromagnetic Compatibility (EMC) Directive
89/336/EEC.
y It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
y The unit is for indoor use only. Use only in a dry location.
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
y The unit must be installed in a location with adequate ventilation, at least 50cm from
EN61000-4-11: 1994.
adjacent surfaces. Be sure that no ventilation slots are blocked.
y Disconnect main power before fuse/lamp replacement or servicing.
&
Harmonized Standard
y Replace fuse/lamp only with the same type.
y Make sure there is no flammable materials close to the unit while operating as it is fire
hazard.
EN60598-1: 2000+ALL:2000+A12:2002
Safety of household and similar electrical appliances
y Use safety cable when fixes this unit. Don’t handle the unit by taking its head only, but
Part 1 : General requirements
always by taking its base.
y Maximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is
higher than this.
y Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during
its operation. Turn off the power and allow about 15 minutes for the unit to cool down
before replacing bulb or serving.
y In the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center. Always
use the same type spare parts.
y Don’t connect the device to any dimmer pack or power pack.
y Do not touch any wire during operation as high voltage might be causing electric shock.
3J
20J
1.Safety Instruction
Please read carefully the instruction, which includes important information
WARNING
about the installation, usage and maintenance.
y Please keep this User Guide for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction booklet.
EC Declaration of Conformity
y Unpack and check carefully there is no transportation damage before using the unit.
y Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
We declare that our products (lighting equipments) comply with the
following specification and bears CE mark in accordance with the
y The unit is designed for use with the HID 150W or ELC 24V 250W (two version). Do not
use any other type of lamp.
provision of the Electromagnetic Compatibility (EMC) Directive
89/336/EEC.
y It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
y The unit is for indoor use only. Use only in a dry location.
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
y The unit must be installed in a location with adequate ventilation, at least 50cm from
EN61000-4-11: 1994.
adjacent surfaces. Be sure that no ventilation slots are blocked.
y Disconnect main power before fuse/lamp replacement or servicing.
&
Harmonized Standard
y Replace fuse/lamp only with the same type.
y Make sure there is no flammable materials close to the unit while operating as it is fire
hazard.
EN60598-1: 2000+ALL:2000+A12:2002
Safety of household and similar electrical appliances
y Use safety cable when fixes this unit. Don’t handle the unit by taking its head only, but
Part 1 : General requirements
always by taking its base.
y Maximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is
higher than this.
y Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during
its operation. Turn off the power and allow about 15 minutes for the unit to cool down
before replacing bulb or serving.
y In the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center. Always
use the same type spare parts.
y Don’t connect the device to any dimmer pack or power pack.
y Do not touch any wire during operation as high voltage might be causing electric shock.
3J
20J
7. Maintenance and Cleaning
Warning
Maintenance (for HID lamp only):
y To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
y Never touch bulb with bare fingers as it is very hot after using.
y Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.
y Do not start on the unit without bulb enclosure or housing are damaged.
y The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
Ignitor
Filter, Ballast, capacitor
y Do not look directly at the light while the bulb is on.
A. As the pictures shown above, if the cable or cable joints turned yellow or black, please
replace the cable or cable joints immediately.
B. Do maintain the fixtures every two months and make sure that all the screws and
Caution
terminals have been locked firmly to make sure the normal performance of the fixtures.
Negligence of maintenance would cause malfunction of the fixture.
There are no user serviceable parts inside the unit. Do not open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact
Cleaning:
your nearest dealer.
The cleaning of internal and external optical lenses and/or mirrors must be
carried out periodically to optimize light output. Cleaning frequency depends on the
environment in which the fixture operates: damp, smoky or particularly dirty
surrounding can cause greater accumulation of dirt on the unit’s optics.
Installation
y Clean with soft cloth using normal glass cleaning fluid.
y Always dry the parts carefully.
The unit should be mounted via its screw holes on the bracket. Always ensure that the
y Clean the external optics at least every 20 days. Clean the internal optics at least every
unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
30/60 days.
structure to which you are attaching the unit is secure and is able to support a weight of 20
kgs for each unit.
19J
4J
7. Maintenance and Cleaning
Warning
Maintenance (for HID lamp only):
y To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
y Never touch bulb with bare fingers as it is very hot after using.
y Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.
y Do not start on the unit without bulb enclosure or housing are damaged.
y The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
Ignitor
Filter, Ballast, capacitor
y Do not look directly at the light while the bulb is on.
A. As the pictures shown above, if the cable or cable joints turned yellow or black, please
replace the cable or cable joints immediately.
B. Do maintain the fixtures every two months and make sure that all the screws and
Caution
terminals have been locked firmly to make sure the normal performance of the fixtures.
Negligence of maintenance would cause malfunction of the fixture.
There are no user serviceable parts inside the unit. Do not open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact
Cleaning:
your nearest dealer.
The cleaning of internal and external optical lenses and/or mirrors must be
carried out periodically to optimize light output. Cleaning frequency depends on the
environment in which the fixture operates: damp, smoky or particularly dirty
surrounding can cause greater accumulation of dirt on the unit’s optics.
Installation
y Clean with soft cloth using normal glass cleaning fluid.
y Always dry the parts carefully.
The unit should be mounted via its screw holes on the bracket. Always ensure that the
y Clean the external optics at least every 20 days. Clean the internal optics at least every
unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
30/60 days.
structure to which you are attaching the unit is secure and is able to support a weight of 20
kgs for each unit.
19J
4J
2. Technical Specification
G. If The pan belt is broken
• Voltage:AC 120V~60Hz or 230V/240V/250V~50/60Hz
1.
Turn off the main power.
2.
Unscrew all the screws (A) and open the base-housing cover (B).
3.
Unplug all the connect wires (C) that from the arm to PC board and ignitor.
in master/slave connection, as many as required and run by built-in program chase
4.
Unscrew the screws (D) that fix the axis gear (E).
sequences automatically or by sound activation through an internal microphone to create
5.
Change a new belt (F) by going through all connect wires that from the arm to base,
• Bulb:HID 150W
ELC 24V 250W
• The unit is DMX 512 fixture. It features full DMX 512 control. It can be also linked together
an intelligent effect.
and through the bridge for correct position.
• It can be operated by DMX 512 control or can be used as an individual unit without a
6.
Set up the gear axis to the bridge and screwed it. Note : do not press the belt.
7.
Put the belt around the axis gear and motor gear.
8.
Plug all the connect wires (C) that form the arm to PC board and ignitor.
• Please use a 3 pin XLR cable/plug when connecting units together.
9.
Adjust the pan home position.
• Accurate focusable optics system and ultra smooth stepping motors. Fan cooled.
10. Screw the base-housing cover (B).
controller.
• Consistent DMX channel enable iRock, iShow and iMove to be link together.
• Features different preprogrammed chase patterns.
• Pan : 540 deg. Tilt : 270 deg.
• Dimension : 290 x 330 x 380 mm
• Weight : 12 kg
Move Spot
Independent gobo wheel with 14 gobos plus open and blackout, including 11
metal, 2 glass and 1 effect gobos with shaking and shutter effect, Independent
color wheel with 11 dichroic colors with rainbow effect.
Move Wash Independent color wheel with 11 dichroic colors with rainbow effect and
independent shutter & dimmer.
2.1 Beam Angle
5J
18J
2. Technical Specification
G. If The pan belt is broken
• Voltage:AC 120V~60Hz or 230V/240V/250V~50/60Hz
1.
Turn off the main power.
2.
Unscrew all the screws (A) and open the base-housing cover (B).
3.
Unplug all the connect wires (C) that from the arm to PC board and ignitor.
in master/slave connection, as many as required and run by built-in program chase
4.
Unscrew the screws (D) that fix the axis gear (E).
sequences automatically or by sound activation through an internal microphone to create
5.
Change a new belt (F) by going through all connect wires that from the arm to base,
• Bulb:HID 150W
ELC 24V 250W
• The unit is DMX 512 fixture. It features full DMX 512 control. It can be also linked together
an intelligent effect.
and through the bridge for correct position.
• It can be operated by DMX 512 control or can be used as an individual unit without a
6.
Set up the gear axis to the bridge and screwed it. Note : do not press the belt.
7.
Put the belt around the axis gear and motor gear.
8.
Plug all the connect wires (C) that form the arm to PC board and ignitor.
• Please use a 3 pin XLR cable/plug when connecting units together.
9.
Adjust the pan home position.
• Accurate focusable optics system and ultra smooth stepping motors. Fan cooled.
10. Screw the base-housing cover (B).
controller.
• Consistent DMX channel enable iRock, iShow and iMove to be link together.
• Features different preprogrammed chase patterns.
• Pan : 540 deg. Tilt : 270 deg.
• Dimension : 290 x 330 x 380 mm
• Weight : 12 kg
Move Spot
Independent gobo wheel with 14 gobos plus open and blackout, including 11
metal, 2 glass and 1 effect gobos with shaking and shutter effect, Independent
color wheel with 11 dichroic colors with rainbow effect.
Move Wash Independent color wheel with 11 dichroic colors with rainbow effect and
independent shutter & dimmer.
2.1 Beam Angle
5J
18J
6. Troubleshooting
3. Lamp
Following are a few common problems that may occur during operation. Here are
In case of replacement of the lamp or maintenance, do not open the fixture
some suggestions for easy troubleshooting:
within 15 minutes until the unit cools down after switching off.
A. The unit does not work, no light and the fan does not work
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
Lamp :
HID 150W
3. Check the power on LED.
ELC 24V 250W
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
1. Always switch off the main supply and never handle the lamp or luminaries when is
hot.
2. Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
alcohol and wipe it with a lint free cloth before installation.
3. Never operate the lamp without appropriate shielding.
of the unit or the previous one.
4. Make sure the lamp is located in the center for the best spot.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
Diagram for Lamp changing
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
1. Make sure the unit does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
1. The lamp is not working well. Check the main voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan on the
head.
17J
6J
6. Troubleshooting
3. Lamp
Following are a few common problems that may occur during operation. Here are
In case of replacement of the lamp or maintenance, do not open the fixture
some suggestions for easy troubleshooting:
within 15 minutes until the unit cools down after switching off.
A. The unit does not work, no light and the fan does not work
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
Lamp :
HID 150W
3. Check the power on LED.
ELC 24V 250W
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
1. Always switch off the main supply and never handle the lamp or luminaries when is
hot.
2. Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
alcohol and wipe it with a lint free cloth before installation.
3. Never operate the lamp without appropriate shielding.
of the unit or the previous one.
4. Make sure the lamp is located in the center for the best spot.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
Diagram for Lamp changing
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
1. Make sure the unit does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
1. The lamp is not working well. Check the main voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan on the
head.
17J
6J
HID 150W Lamp Installation Or Replacement
5.5 DMX512 Connection
The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels.
• Always switch power off before installing or replacing the lamp. Never try to replace the
1
2
3
4
lamp when it is hot.
• Do not touch the bulb with bare hands. Cleaning the lamp with denatured alcohol and wipe
with a lint free cloth when lamp is dirty.
DMX512
120 ohm 1/4W
COMMON
1
INPUT
3
2
DMX +
DMX -
1
3
OUTPUT
2
Termination reduces signal errors and to avoid signal
transmission problems and interference. It is always
advisable to connect a DMX terminal.
(Resistance 120 ohm 1/4W) between pin2 (DMX-) and
pin3 (DMX+) of the last fixture.
1.
1
3
2
If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
2.
At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it
in the DMX-output of the last unit.
3.
Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to
the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is
1. Loose the screw on the housing cover.
a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
2. Loose the screws of the lamp wire from terminator
connectors can easily distort the signal and shut down the system.
3. Remove the old lamp from the fixture.
4.
4. Please be care to install the lamp into case, make sure it wedge tightly that it
can not move easily. WARNING: impropriety install will cause the lamp
The DMX output and input connectors are pass-through to maintain the DMX circuit,
when power is disconnected to the unit.
5.
lifespan shorten and maybe explosion during operation.
Each lighting unit needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
5. Connect the lamp wire to the terminator as before.
6.
The end of the DMX 512 system should be terminated to reduce signal errors.
6. Please reinstall step 2 and step 1.
7.
3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
7J
16J
HID 150W Lamp Installation Or Replacement
5.5 DMX512 Connection
The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels.
• Always switch power off before installing or replacing the lamp. Never try to replace the
1
2
3
4
lamp when it is hot.
• Do not touch the bulb with bare hands. Cleaning the lamp with denatured alcohol and wipe
with a lint free cloth when lamp is dirty.
DMX512
120 ohm 1/4W
COMMON
1
INPUT
3
2
DMX +
DMX -
1
3
OUTPUT
2
Termination reduces signal errors and to avoid signal
transmission problems and interference. It is always
advisable to connect a DMX terminal.
(Resistance 120 ohm 1/4W) between pin2 (DMX-) and
pin3 (DMX+) of the last fixture.
1.
1
3
2
If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
2.
At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it
in the DMX-output of the last unit.
3.
Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to
the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is
1. Loose the screw on the housing cover.
a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
2. Loose the screws of the lamp wire from terminator
connectors can easily distort the signal and shut down the system.
3. Remove the old lamp from the fixture.
4.
4. Please be care to install the lamp into case, make sure it wedge tightly that it
can not move easily. WARNING: impropriety install will cause the lamp
The DMX output and input connectors are pass-through to maintain the DMX circuit,
when power is disconnected to the unit.
5.
lifespan shorten and maybe explosion during operation.
Each lighting unit needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
5. Connect the lamp wire to the terminator as before.
6.
The end of the DMX 512 system should be terminated to reduce signal errors.
6. Please reinstall step 2 and step 1.
7.
3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
7J
16J
5.4 DMX 512 Configuration
4. How To Set The Unit
Item
Ch 1 Ch 2 Ch 3
Ch 4
Move Spot
Pan
Tilt
Shutter/Sharking Gobo
Move Wash Pan
Tilt
Shutter
Ch 5
Ch 6
Ch 7
4.1 Control Panel
Color
No function Color No function Dimmer
Display
To show the various menus and the selected functions.
LED
DMX
On
DMX input present
MASTER
On
Master Mode
SLAVE
On
Slave Mode
SOUND
Flashing
Sound activation
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
To confirm the selected functions
Button
Remote controller input
By connect to the 1/4” microphone jack to control the unit for stand by, function and mode
Sensitivity
To adjust the sound sensitivity.
Microphone
To receive audio signal for sound activation.
DMX input/output
For DMX512 link, use 3-pin XLR plug cable to link the unit together.
15J
8J
5.4 DMX 512 Configuration
4. How To Set The Unit
Item
Ch 1 Ch 2 Ch 3
Ch 4
Move Spot
Pan
Tilt
Shutter/Sharking Gobo
Move Wash Pan
Tilt
Shutter
Ch 5
Ch 6
Ch 7
4.1 Control Panel
Color
No function Color No function Dimmer
Display
To show the various menus and the selected functions.
LED
DMX
On
DMX input present
MASTER
On
Master Mode
SLAVE
On
Slave Mode
SOUND
Flashing
Sound activation
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
To confirm the selected functions
Button
Remote controller input
By connect to the 1/4” microphone jack to control the unit for stand by, function and mode
Sensitivity
To adjust the sound sensitivity.
Microphone
To receive audio signal for sound activation.
DMX input/output
For DMX512 link, use 3-pin XLR plug cable to link the unit together.
15J
8J
Stand by
4.2 Main Function
To select any of the given functions, press the MENU button up to when the required one is
showing on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
Move
Spot
Function
press the ENTER button to setup or it will automatically return to the main functions without
any change after idling 8 seconds. To go back to the functions without any change press the
Mode
MENU button. The main functions are showing below:
Stand by
DMX512 Address Setting
Show mode 1
Show mode 2
Show mode 3
Show mode 4
Slave Mode " Normal "
Slave mode " 2 Light Show "
Blackout Mode " Yes Blackout "
Blackout Mode " No Blackout "
Normal Color
Split Color
Pan Normal
Pan Inversion
Tilt Normal
Tilt Inversion
Dimmer Normal
Dimmer Inversion
LED on
LED off
Display Normal
Display Inversion
MENU
Move
Wash
Function
Mode
Blackout the unit
Strobe
1.Gobo / Color
sync.
strobe
2.Sync. strobe
3.Two-light strobe
Sound 1
(LED off )
Blackout the unit
Strobe
1.Color sync.
strobe
2.Sync. strobe
3.Two-light strobe
Sound 1
(LED off )
X/Y moving show
mode selection
( Show 1 ~ Show
4)
Please refer to
Show mode in
4.2 Main Function
Sound 2
(LED normal
blinking)
Color/Gobo
selection
1. Hold on for gobo
change.
2. Press shortly for
color change
X/Y moving setting
1.Pan position
2.Tilt position
First set Master
unit, then set Slave
units’ position
Slow/Sound 3
(LED on)
Position/ Latch
(LED fast blinking)
X/Y moving show
mode selection
( Show 1 ~ Show
4)
Please refer to
Show mode in
4.2 Main Function
Sound 2
(LED normal
blinking)
Color selection
X/Y moving setting
1.Pan position
2.Tilt position
3.Dimmer
First set Master
unit, then set Slave
units’ position
Position/ Latch
(LED fast blinking)
Slow/Sound 3
(LED on)
5.3.1 iSolution Operation
♦ Consistent DMX configuration enable iMove to be linked together with iRock and iShow
and controlled at the same time.
♦ DMX address can be set remotely by iLead controller ( please refer to the user manual of
iLead controller ). No need to calculate the DMX channels of each fixture in the chain.
♦ Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
An universal DMX controller to control the units, you have to set DMX address from
Focus Adjust
1 to 512 channel so that the units can receive DMX signal.
Self-Test
Press the MENU button up to when the
Fixture Hours
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
is showing on the display. Pressing ENTER
Once the address has been selected, press and keep ENTER button pressed up to when
Reset
the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again. If you use please refer to the
DMX 512 Address Setting
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press the ENTER button to setup or automatically
following diagram to address your DMX512 channel for the first 4 units.
DMX address can be setting remotely by IL-0824 controller. No need to calculate the DMX
channels of each fixture in the chain.
return to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.
9J
14J
Stand by
4.2 Main Function
To select any of the given functions, press the MENU button up to when the required one is
showing on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
Move
Spot
Function
press the ENTER button to setup or it will automatically return to the main functions without
any change after idling 8 seconds. To go back to the functions without any change press the
Mode
MENU button. The main functions are showing below:
Stand by
DMX512 Address Setting
Show mode 1
Show mode 2
Show mode 3
Show mode 4
Slave Mode " Normal "
Slave mode " 2 Light Show "
Blackout Mode " Yes Blackout "
Blackout Mode " No Blackout "
Normal Color
Split Color
Pan Normal
Pan Inversion
Tilt Normal
Tilt Inversion
Dimmer Normal
Dimmer Inversion
LED on
LED off
Display Normal
Display Inversion
MENU
Move
Wash
Function
Mode
Blackout the unit
Strobe
1.Gobo / Color
sync.
strobe
2.Sync. strobe
3.Two-light strobe
Sound 1
(LED off )
Blackout the unit
Strobe
1.Color sync.
strobe
2.Sync. strobe
3.Two-light strobe
Sound 1
(LED off )
X/Y moving show
mode selection
( Show 1 ~ Show
4)
Please refer to
Show mode in
4.2 Main Function
Sound 2
(LED normal
blinking)
Color/Gobo
selection
1. Hold on for gobo
change.
2. Press shortly for
color change
X/Y moving setting
1.Pan position
2.Tilt position
First set Master
unit, then set Slave
units’ position
Slow/Sound 3
(LED on)
Position/ Latch
(LED fast blinking)
X/Y moving show
mode selection
( Show 1 ~ Show
4)
Please refer to
Show mode in
4.2 Main Function
Sound 2
(LED normal
blinking)
Color selection
X/Y moving setting
1.Pan position
2.Tilt position
3.Dimmer
First set Master
unit, then set Slave
units’ position
Position/ Latch
(LED fast blinking)
Slow/Sound 3
(LED on)
5.3.1 iSolution Operation
♦ Consistent DMX configuration enable iMove to be linked together with iRock and iShow
and controlled at the same time.
♦ DMX address can be set remotely by iLead controller ( please refer to the user manual of
iLead controller ). No need to calculate the DMX channels of each fixture in the chain.
♦ Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
An universal DMX controller to control the units, you have to set DMX address from
Focus Adjust
1 to 512 channel so that the units can receive DMX signal.
Self-Test
Press the MENU button up to when the
Fixture Hours
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
is showing on the display. Pressing ENTER
Once the address has been selected, press and keep ENTER button pressed up to when
Reset
the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again. If you use please refer to the
DMX 512 Address Setting
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press the ENTER button to setup or automatically
following diagram to address your DMX512 channel for the first 4 units.
DMX address can be setting remotely by IL-0824 controller. No need to calculate the DMX
channels of each fixture in the chain.
return to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.
9J
14J
5. How To Control The Unit
Show Mode
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
Press the MENU button up to when the
2. By easy controller
button and the display will blink. Use DOWN and UP button to select the
3. By iLead controller ( please refer to the user guide of iLead ) or universal DMX controller
or
(show 2) or
is showing on the display. Pressing ENTER
(show 3) or
(show 1)
(show 4) mode. Once the mode has
No need to turn the unit off when you change the DMX address, as new DMX address
been selected, press the ENTER button to setup or automatically return to the main
setting will be effected at once. Every time you turn the unit on, it will show IM-5S/IM-5W on
functions without any change after 8 seconds. To go back to the functions without any
the display and move all the motors to their ‘home’ position and you may hear some noises
change press the MENU button again.
for about 20 seconds. After that the unit will be ready to receive DMX signal or run the built
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
in programs.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on the speaker, The spot is always projecting
5.1 Master/Slave Built In Preprogrammed Function
to the audience’s direction; i.e in front of the stage. Pan
By linking the units in master/slave connection, the first unit will control the other
movement angle ( left to right to left ): 160°. Tilt movement
units to give an automatic, sound activated, synchronized light show. This function
angle: 90° ( 60° above horizon; 30° below horizon.)
is good when you want an instant show. You have to set the first unit in master
and select
mode
(show 1) or
(show 2) or
Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in
front of the stage. Pan movement angle ( left to right to
(show 3)
left ) :160°.
(show 4) mode. Its DMX input jack will have nothing plugged into it, and
or
Its master LED will be constantly on and sound LED will flash to the music. The
other units will have to set in slave mode
and select
Tilt movement angle: 90° ( vertically, front 75°;
back 15° )
(normal) or
Slave Mode
(2 light show) mode, Their DMX cables plugged into the DMX input jacks
(daisy chain) and the slave led lights will constantly on.
Press the MENU button up to when the
2-light show
ENTER button and the display will blink. Use DOWN and UP button to select the
In
(slave mode),
means the unit works normally and
means
2-light show. In order to create a great light show, you can set
on the second unit to
get contrast movement to each other, even if you have two units only.
is showing on the display. Pressing
(2 light show) mode. Once the mode has been selected, press the
(normal) or
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
5.2 Easy Controller
Blackout Mode
The easy remote control is used only in master/slave mode. By
connecting to the 1/4” microphone jack of the first unit, you will find
Press the MENU button up to when the
is showing on the display. Pressing
that the remote control on the first unit will control all the other units
ENTER button and the display will blink. Use DOWN and UP button to select the
functions press the MENU button again.
(yes blackout) or
(no blackout) mode. Once the mode has been selected, press
the ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
13J
10J
5. How To Control The Unit
Show Mode
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
Press the MENU button up to when the
2. By easy controller
button and the display will blink. Use DOWN and UP button to select the
3. By iLead controller ( please refer to the user guide of iLead ) or universal DMX controller
or
(show 2) or
is showing on the display. Pressing ENTER
(show 3) or
(show 1)
(show 4) mode. Once the mode has
No need to turn the unit off when you change the DMX address, as new DMX address
been selected, press the ENTER button to setup or automatically return to the main
setting will be effected at once. Every time you turn the unit on, it will show IM-5S/IM-5W on
functions without any change after 8 seconds. To go back to the functions without any
the display and move all the motors to their ‘home’ position and you may hear some noises
change press the MENU button again.
for about 20 seconds. After that the unit will be ready to receive DMX signal or run the built
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
in programs.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on the speaker, The spot is always projecting
5.1 Master/Slave Built In Preprogrammed Function
to the audience’s direction; i.e in front of the stage. Pan
By linking the units in master/slave connection, the first unit will control the other
movement angle ( left to right to left ): 160°. Tilt movement
units to give an automatic, sound activated, synchronized light show. This function
angle: 90° ( 60° above horizon; 30° below horizon.)
is good when you want an instant show. You have to set the first unit in master
and select
mode
(show 1) or
(show 2) or
Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in
front of the stage. Pan movement angle ( left to right to
(show 3)
left ) :160°.
(show 4) mode. Its DMX input jack will have nothing plugged into it, and
or
Its master LED will be constantly on and sound LED will flash to the music. The
other units will have to set in slave mode
and select
Tilt movement angle: 90° ( vertically, front 75°;
back 15° )
(normal) or
Slave Mode
(2 light show) mode, Their DMX cables plugged into the DMX input jacks
(daisy chain) and the slave led lights will constantly on.
Press the MENU button up to when the
2-light show
ENTER button and the display will blink. Use DOWN and UP button to select the
In
(slave mode),
means the unit works normally and
means
2-light show. In order to create a great light show, you can set
on the second unit to
get contrast movement to each other, even if you have two units only.
is showing on the display. Pressing
(2 light show) mode. Once the mode has been selected, press the
(normal) or
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
5.2 Easy Controller
Blackout Mode
The easy remote control is used only in master/slave mode. By
connecting to the 1/4” microphone jack of the first unit, you will find
Press the MENU button up to when the
is showing on the display. Pressing
that the remote control on the first unit will control all the other units
ENTER button and the display will blink. Use DOWN and UP button to select the
functions press the MENU button again.
(yes blackout) or
(no blackout) mode. Once the mode has been selected, press
the ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
13J
10J
ENTER button and the display will blink. Use DOWN and UP button to select the
Color Mode
Press the MENU button up to when the
is showing on the display. Pressing
seconds. To go back to the functions without any change press the MENU button again.
ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or
(Led on) or
(Led off) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8
(split color) mode. Once the mode has been selected, press the
Display Inversion
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
again.
when the
is blinking on the display. Use the ENTER button to change to the mode
(display inversion), It will automatically store after 8 seconds. Or press the ENTER
Pan Inversion
button again return to the mode
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
or
(normal)
(pan inversion) mode. Once the mode has been selected, press the ENTER
(display normal). To go back to the functions press
the MENU button again.
Display normal mode for the fixture putting on the floor.
Display inversion mode for the fixture fixing under ceiling.
button to setup or automatically return to the main functions without any change after 8
Focus Adjust
seconds. To go back to the functions without any change press the MENU button again.
Press the MENU button up to when the
Tilt Inversion
button, the unit will focus on tilt 90°, and then the unit will focus on pan 0°, pan 90°, pan180°,
Press the MENU button up to when the
is showing on the display. Pressing
pan270° in every pressing ENTER button. To go back to the functions press the MENU
button again.
ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or
is blinking on the display. Pressing ENTER
(tilt inversion) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change
Self-Test
after 8 seconds. To go back to the functions without any change press the MENU button
Press the MENU button up to when the
again.
button and the unit will run self-test by built in program. To go back to the functions press the
is blinking on the display. Pressing ENTER
MENU button again.
Dimmer Inversion
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
or
(normal)
(dimmer inversion) mode. Once the mode has been selected, press the ENTER
Fixture Hours
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button again.
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
Reset
Press the MENU button up to when the
Led Display
is blinking on the display. Pressing ENTER
button and all channels of the unit will return to their standard position. To go back to the
Press the MENU button up to when the
is showing on the display. Pressing
11J
functions without any change press the MENU button agai
12J
ENTER button and the display will blink. Use DOWN and UP button to select the
Color Mode
Press the MENU button up to when the
is showing on the display. Pressing
seconds. To go back to the functions without any change press the MENU button again.
ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or
(Led on) or
(Led off) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8
(split color) mode. Once the mode has been selected, press the
Display Inversion
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
again.
when the
is blinking on the display. Use the ENTER button to change to the mode
(display inversion), It will automatically store after 8 seconds. Or press the ENTER
Pan Inversion
button again return to the mode
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
or
(normal)
(pan inversion) mode. Once the mode has been selected, press the ENTER
(display normal). To go back to the functions press
the MENU button again.
Display normal mode for the fixture putting on the floor.
Display inversion mode for the fixture fixing under ceiling.
button to setup or automatically return to the main functions without any change after 8
Focus Adjust
seconds. To go back to the functions without any change press the MENU button again.
Press the MENU button up to when the
Tilt Inversion
button, the unit will focus on tilt 90°, and then the unit will focus on pan 0°, pan 90°, pan180°,
Press the MENU button up to when the
is showing on the display. Pressing
pan270° in every pressing ENTER button. To go back to the functions press the MENU
button again.
ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or
is blinking on the display. Pressing ENTER
(tilt inversion) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change
Self-Test
after 8 seconds. To go back to the functions without any change press the MENU button
Press the MENU button up to when the
again.
button and the unit will run self-test by built in program. To go back to the functions press the
is blinking on the display. Pressing ENTER
MENU button again.
Dimmer Inversion
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
or
(normal)
(dimmer inversion) mode. Once the mode has been selected, press the ENTER
Fixture Hours
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button again.
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
Reset
Press the MENU button up to when the
Led Display
is blinking on the display. Pressing ENTER
button and all channels of the unit will return to their standard position. To go back to the
Press the MENU button up to when the
is showing on the display. Pressing
11J
functions without any change press the MENU button agai
12J
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement