Industrial Thermometers
INDUSTRIAL THERMOMETERS
Industrial
thermometers
Selecting the correct thermometer for an application is by
definition very important, to achieve the maximum accuracy
and repeatability of the temperature reading.
The selection criteria for a digital thermometer should include:
z measurement range
z resolution of the reading 1 °C, 0.1 °C or 0.01 °C
z desired accuracy
z response time
ETI digital thermometers utilise one of three types of
temperature sensors, thermocouple, NTC thermistor
and resistance temperature detectors (RTD or PT100).
Thermocouple thermometers and probes are fast to respond to
changes in temperature, they also have a wide measurement
range. Resistance temperature detector and NTC thermistor
thermometers and probes are slower to respond to changes in
temperature, but generally more accurate, although thermistor
probes have a limited measurement range.
-200
0
200
400
600
800
1000
1200 °C
NTC
PT100 or RTD
THERMOCOUPLE TYPE T
THERMOCOUPLE TYPE K
NTC thermistors
NTC thermistor probes are also based on a temperature
dependent resistance change in the sensor element. But
unlike resistance thermometer detectors, thermistors have a
negative temperature coefficient, i.e the resistance decreases
with increasing temperature.
resistance temperature detectors (PT100 or RTD)
Resistance temperature detector (PT100 or RTD) probes
consist of a flat film or wire wound platinum resistance sensor
element. The measurement resistance value changes in line
with the temperature being measured.
thermocouples
Thermocouple probes consist of two wires of dissimilar metals
or metal alloys welded together. Thermocouples are based on
the thermoelectric (Seebeck) effect. There are various types
of thermocouple, types K and T being the most common,
although type K is by far the most widely used.
*
www.servesafe.in
fax
+91 022 27656636
with interchangeable thermocouple probes
NEW!
FREE traceable certificate of calibration included
Elite model with max/min & a backlight
wide temperature measurement range
minimum five-years battery life
The Therma 1 and 3 digital thermometers are rugged and easy to use instruments
that operate through the range of -100 to 1370 °C with a 0.1 °C or 1 °C
resolution. The thermometers are housed in a robust ABS case that contains
'Biomaster' additive that helps to reduce bacterial growth.
The Therma 1 and 3 feature a large, easy to read, LCD display with open
circuit 'Err' and low battery indication. Each thermometer is powered by three
1.5 volt AAA batteries that gives a minimum of five years battery life. The units
will power off automatically after ten minutes, maximising battery life. This feature
can be disabled by the user, if required.
ETI offers an extensive range of interchangeable type K thermocouple probes, for a variety
of different applications, see pages 49 to 54 for full details.
Therma Elite
The Therma Elite incorporates all the features of a Therma 1 thermometer, but with the addition of
a backlit display, max/min memory function and a mode button for the selection of 0.1/1 °C/°F.
The thermometer also incorporates a calibration trim function (±2 °C) which allows users to
compensate for thermocouple probe errors.
optional accessories
‡ 830-251 protective silicone boot - the Therma series is waterproof
to IP63 when used in conjunction with this protective boot
‡ 832-050 wall bracket (screws not supplied) and protective
silicone boot
order code description
221-041 Therma 1
221-043 Therma 3
221-061 Therma Elite
830-251 protective silicone boot
832-050 wall bracket & protective boot
the Therma series is exclusive of probe
specification
Therma 1/Elite
Therma 3
range 0.1 °C
-99.9 to 299.9 °C
n/a
range 1 °C
300 to 1372 °C
-100 to 1372 °C
resolution
0.1 °C & 1 °C
1 °C
accuracy
±0.4 °C ±0.1 %
±1 °C ±0.1 %
battery
3 x 1.5 volt AAA
battery life
minimum 5 years (10000 hours)
sensor type
K thermocouple
display
12 mm LCD
dimensions
25 x 56 x 128 mm
weight
130 grams
FREE traceable certificate of calibration included
*
Sales
+91 022 27666033 / 27664080
email
[email protected]
INDUSTRIAL THERMOMETERS
Therma 1, 3 & Elite Thermometers
INDUSTRIAL THERMOMETERS
2202 & 2203 Thermometers
T1 or T2 temperature or T1 minus T2 differential
ideal for radiator balancing or HVAC
V
applications
FREE traceable certificate of calibration
two models 0.1 °C or 1 °C resolution
two-input sockets
The differential digital thermometers allow the user to use two type K thermocouple
probes simultaneously. The display can be switched to show probe T1 or T2
temperature or the difference between probes T1 and T2 (T1-T2). This allows,
for example, the temperature drop across radiators or the temperature rise or fall
of two items to be measured.
The thermometers measure temperature over the range of -50 to 550 °C with a
1 °C resolution or -49.9 to 199.9 °C with a 0.1 °C resolution. Both thermometers
feature a custom, LCD display with °C, T1, T2, diff, hold, open circuit and low
battery indication. The units incorporate an auto-power off facility that
automatically turns the instrument off after approximately three minutes,
maximising battery life.
Both the 2202 and 2203 incorporate easy
to use, silicone rubber key switches which
activate the various functions of each
instrument. Conveniently located are the
front-mounted thermocouple probe sockets
that allow a wide range of interchangeable
thermocouple type K probes to be
connected to the instrument. For full
details of the range of thermocouple
probes available, see pages 49 to 54.
optional accessories
‡ 830-205 protective boot
‡ 832-115 wall bracket (screws not supplied)
‡three-point temperature checker (page 82)
order code description
221-222
2202
221-233
2203
830-205
protective boot
832-115
wall bracket
the thermometers are exclusive of probe
specification
2202
2203
range
-49.9 to 199.9 °C
-50 to 550 °C
resolution
0.1 °C
1 °C
accuracy 1 °C
±0.5 °C ±1 %
±1 °C ±1 %
battery
9 volt PP3
battery life
150 hours
sensor type
K thermocouple
display
12.7 mm LCD
dimensions
35 x 73 x 141 mm
weight
300 grams
FREE traceable certificate of calibration included
*
www.servesafe.in
fax
+91 022 27656636
excellent value for money - FREE carrying case
These thermometer kits are designed for specific industrial applications. For a full specification on each thermometer
see pages 37 and 38. These kits represent excellent value for money as they are supplied in a FREE carrying case.
HVAC thermometer kit 0.1 °C
Each kit contains
1 x 221-222 ETI 2202 thermometer
1 x 123-160 penetration probe
2 x 133-040 pipe clamp probes
1 x 834-300 ABS carrying case
HVAC thermometer kit 1 °C
Each kit contains
1 x 221-233 ETI 2203 thermometer
1 x 123-160 penetration probe
2 x 133-040 pipe clamp probes
1 x 834-300 ABS carrying case
order code description
860-070
HVAC
V
kit 0.1 °C
860-080
HVAC
V
kit 1 °C
FREE traceable certificate of calibration included
Legionnaires' Thermometer Kit
NEW!
temperature monitoring of water
Incorrect water temperature is a key risk factor for legionella growth. The legionella bacteria multiply in water at
temperatures between 20 to 45 °C, particularly if a supply of nutrients is present, such as scale, rust, sludge or
algae. A typical method of control is to store cold water below 20 °C. Hot water should be stored above 60 °C
and distributed at above 50 °C.
Legionnaires' kit 1 °C
Each kit contains
1 x 221-041 Therma 1 thermometer
1 x 123-160 penetration probe
1 x 123-030 precision ribbon surface probe
1 x 133-362 PTFE wire probe
1 x 806-150 count up/down timer
1 x 836-022 mini tub of 70 ProbeWipes
1 x 834-150 ABS carrying case
order code description
860-860
legionnaires' thermometer kit
FREE traceable certificate of calibration included
*
Sales
+91 022 27666033 / 27664080
email
[email protected]
INDUSTRIAL THERMOMETERS
HVAC Thermometer Kits
INDUSTRIAL THERMOMETERS
Precision PT100 Thermometers
0.1 °C or 0.01 °C resolution with a high accuracy
high accuracy ±0.2 °C or 0.05 °C
NEW!
max/min memory function
interchangeable PT100 probes
FREE certificate of calibration included
High accuracy is one of the outstanding features of the Precision
thermometers. There are two models available, the Precision and
Precision Plus. The Precision measures temperature over the range
of 199.9 to 499.9 °C with a 0.1 °C resolution and high accuracy
of ±0.2 °C. The Precision Plus measures temperature over the
range of -199.99 to 199.99 °C with a 0.01 °C resolution and high
accuracy of ±0.05 °C. Please note: the accuracies quoted are for
the instruments only.
Conveniently located on the front of the instrument are the on/off, max/
min and display hold buttons. The Binder probe socket is positioned at the
top of the instrument which enables a variety of probes to be used depending
on the application.
The Precision thermometers feature a large, easy to read, LCD display with open
circuit 'Err' and low battery indication. Each thermometer is powered by three 1.5 volt
AAA batteries that gives a minimum of 2000 hours battery life. The units will power off
automatically after ten minutes, maximising battery life. This feature can be disabled
by the user, if required.
ETI offers a range of interchangeable PT100 Class A probes for use with the
Precision thermometer, see page 56 for full details. The Precision Plus is
supplied with a 160-222 PT100 1/10th DIN liquid probe and a UKAS
Certificate of Calibration.
For regularly checking the accuracy of each Precision thermometer,
a range of calibration test caps complete with a UKAS Certificate
of Calibration are available, see page 82.
optional accessories
‡ 830-251 protective silicone boot - the
Precision thermometers are waterproof to
IP63 when used in conjunction with this
protective boot
‡ 832-050 wall bracket (screws not supplied)
and protective silicone boot
‡calibration test caps, see page 82
order code description
222-053
Precision thermometer
222-051
Precision Plus thermometer
830-251
protective silicone boot
832-050
wall bracket & protective boot
222-053 Precision is exclusive of probe
222-051 Precision Plus is inclusive of probe
specification
Precision
Precision Plus
range
-199.9 to 499.9 °C
-199.99 to 199.99 °C
resolution
0.1 °C
0.01 °C
accuracy
±0.2 °C
±0.05 °C
battery
3 x 1.5 volt AAA
battery life
2000 hours
sensor type
PT100
display
10 mm LCD
dimensions
25 x 56 x 128 mm
weight
130 grams
222-053 Precision includes FREE traceable certificate of calibration
222-051 Precision Plus includes UKAS Certificate of Calibration
*
www.servesafe.in
fax
+91 022 27656636
±0.05 °C high system accuracy
NEW!
range -199.99 to 199.99 °C
5-point UKAS Certificate included
ideal for calibration comparison checks
supplied complete with high accuracy probe
The Reference thermometer is a high accuracy PT100
instrument that is supplied with a 5-point UKAS Certificate
of Calibration. Each certificate indicates deviations from
standards at various check points: -18, 0, 40, 70 and
100 °C. Special ranges may be certified by arrangement
with the ETI UKAS calibration laboratory.
The Reference thermometer is ideal for comparison
checking the calibration and accuracy of other
thermometers and probes, when used in conjunction with a
stable temperature heat or chill source, see pages 78 and
79. The instrument and probe measures temperature over
the range of -199.99 to 199.99 °C with a resolution of
0.01 °C and an accuracy of ±0.05 °C. The unit features
a simple on/off push button with low battery and open
circuit 'Err' and low battery indication, when applicable.
The Reference thermometer is supplied with
a permanently attached, high accuracy probe
incorporating a 1/10th DIN PT100 sensor. The probe
measures Ø3.3 x 130 mm and is supplied with a one
metre PVC lead.
0601
A 5-point UKAS Certificate of Calibration is
included with each Reference thermometer
Comparator
The Reference thermometer (above) is being used
in conjunction with an infrared thermometer and
the Comparator.
order code
222-055
814-132
description
Reference
Comparator
specification
Reference
range
-199.99 to 199.99 °C
resolution
0.01 °C
accuracy
±0.05 °C (-30 to 150 °C) otherwise ±0.1 °C
battery
3 x 1.5 volt AAA
battery life
2000 hours
sensor type
PT100 1/10th DIN
display
10 mm LCD
dimensions
25 x 56 x 128 mm
weight
210 grams
a UKAS Certificate of Calibration is included
*
Sales
+91 022 27666033 / 27664080
email
[email protected]
INDUSTRIAL THERMOMETERS
Reference Thermometer
INDUSTRIAL THERMOMETERS
MicroTherma 1 Thermometer
in-built microprocessor for automatic re-calibration
0.1 °C resolution over the full range
should never need re-calibrating
FREE traceable certificate of calibration
type K, J, T, R, N, S or E thermocouple probes
The MicroTherma 1 microprocessor thermometer measures
temperature over the range of -270 to 1768 °C with a
0.1 °C resolution over the entire range. Each MicroTherma
1 thermometer incorporates an easy to read, custom
4½-digit dual LCD display with open circuit, low battery,
hold, max/min and °C/°F indication.
The unit should never need re-calibrating as the built-in
microprocessor enables the instrument to continuously
and automatically carry out self-diagnostic re-calibration.
An additional feature allows the user to adjust the
reading (±2.5 °C) to offset any probe errors, correcting
any inaccuracies of the thermocouple probe. Each
thermometer thereafter will automatically store, display
the offset and adjust the instrument for the known
probe error, maximising system accuracy.
The MicroTherma 1 has the versatility of accepting any type K, J, T, R, N, S or E thermocouple probe, the probe type
is simply selected through the mode button. The unit incorporates both max and min readings with a reset function
and also features an auto-power off facility that maximises the battery life, turning the instrument off automatically
after 30 minutes, this function can be disabled, by the user, if not required. Other selectable parameters include:
display contrast and internal CJC temperature reading. For details of the extensive range of thermocouple probes
available, see pages 49 to 54.
optional accessories
‡ 830-205 protective boot
‡ 832-115 wall bracket (screws not supplied)
order code description
221-091
MicroTherma 1
830-205
protective boot
832-115
wall bracket
the MicroTherma 1 is exclusive of probe
specification
MicroTherma 1
range
-270 to 1768 °C
resolution
0.1 °C/°F
accuracy
±0.2 °C ±1 digit
battery
2 x 1.5 volt AAA alkaline
battery life
1000 hours
sensor type
thermocouple type K, J, T, R, N, S & E - selectable
display
12.7 mm LCD
dimensions
35 x 73 x 141 mm
weight
220 grams
FREE traceable certificate of calibration included
*
www.servesafe.in
fax
+91 022 27656636
in-built microprocessor for automatic re-calibration
thermocouple type K, J, T, R, N, S or E available
self-diagnostic calibration
FREE traceable certificate of calibration
max/min memory function
The MicroTherma 2 microprocessor thermometers
measure temperature over the range of -270 to 1768 °C
with a 0.1 °C/°F resolution over the entire range. Each
microprocessor thermometer incorporates an easy to
read, multi-function LCD display with open circuit, low
battery, hold, max/min and °C/°F indication.
The thermometers should never need re-calibrating as
the built-in microprocessor enables the instruments to
continuously and automatically carry out self-diagnostic
re-calibration. An additional feature allows the user to
adjust the reading (±2.5 °C) to offset any probe errors,
correcting any inaccuracies of the thermocouple
probe. Each thermometer thereafter will automatically
store the offset and adjust the instrument for the
known probe error, maximising accuracy.
Seven models are available that utilise type K, J, T, R, N, S or E thermocouple probes. The instrument also features
an auto-power off facility which maximises the battery life, turning the instrument off automatically after 30 minutes.
Other selectable parameters include: display contrast and internal CJC temperature reading. For details of the
extensive range of thermocouple probes available, see pages 49 to 54.
optional accessories
‡ 830-205 protective boot
‡ 832-115 wall bracket (screws not supplied)
order code description
range
221-092
MicroTherma 2K -200 to 1372 °C
227-093
MicroTherma 2T -270 to 400 °C
229-094
MicroTherma 2J -200 to 1200 °C
229-095
MicroTherma 2N -200 to 1300 °C
229-096
MicroTherma 2S
0 to 1768 °C
229-097
MicroTherma 2E -140 to 1000 °C
229-098
MicroTherma 2R
0 to 1768 °C
830-205
protective boot
832-115
wall bracket
the MicroTherma 2 series is exclusive of probe
specification
MicroTherma 2
range
-270 to 1768 °C (dependent on TC type see above)
resolution
0.1 °C/°F
accuracy
±0.2 °C ±1 digit
battery & battery life
2 x 1.5 volt AAA alkaline - 1000 hours
sensor type
thermocouple type K, J, T, R, N, S or E
display
12.7 mm LCD
dimensions
35 x 73 x 141 mm
weight
220 grams
FREE traceable certificate of calibration included
*
Sales
+91 022 27666033 / 27664080
email
[email protected]
INDUSTRIAL THERMOMETERS
MicroTherma 2 Thermometer
INDUSTRIAL THERMOMETERS
MiniTherma™ K
thermocouple thermometer
interchangeable type K thermocouple probes
water resistant offering IP65 protection
The MiniTherma K thermometer is designed for versatility and ease
of use. The instrument accepts a miniature type K thermocouple
plug that enables a variety of interchangeable probes to be
used. The thermometer incorporates a clear digital display with
a precise read-out of temperature over the range of -59.9 to
1399 °C with a 0.1 °C resolution between -59.9 to 199.9 °C
thereafter 1 °C.
The unit features a display hold function and both low battery and
open circuit indication are also displayed, when applicable. An
auto-power off facility turns the instrument off after four minutes,
maximising battery life.
The MiniTherma K is lightweight, at less than 40 grams. The
case is manufactured from high impact ABS plastic designed to
cope with routine day-to-day applications. Each MiniTherma
K is supplied with a FREE OF CHARGE hand held penetration
probe (133-988, as illustrated) and battery.
order code
810-998
specification
range
resolution
accuracy
battery
battery life
sensor type
display
dimensions
weight
MiniTherma K
-59.9 to 1399 °C
0.1 °C (1 °C above 199.9 °C)
±1 % or ±1 °C over the full range
3 volt CR2032 lithium coin cell
100 hours
K thermocouple
11 mm LCD
19 x 40 x 76 mm
36 grams
description
MiniTherma K
plug-mounted probes
These plug-mounted probes are mounted directly into miniature type K thermocouple plugs. This provides an
economical solution to many temperature measuring applications and allows the option of one-handed operation.
order code
penetration probe
Ø3.3 x 120 mm
fast response probe
Ø1 mm tip x 90 mm
air or gas probe
Ø3.3 x 120 mm
ribbon surface probe
Ø8 x 120 mm
FEP (plastic) probe
Ø3.2 x 40 mm
This plug-mounted, stainless steel, penetration probe is
strong and versatile. Ideal for a variety of applications
i.e. liquids or semi-solids. Response time less than three
seconds. Maximum tip temperature 250 °C.
133-161
This plug-mounted, fast-response, penetration probe
is designed for measuring the temperature of soft
substances and liquids. Response time less than one
second. Maximum tip temperature 250 °C.
133-151
This plug-mounted air/gas probe has a perforated
stainless steel tip for fast response. Ideal for measuring
the temperature of air conditioning. Response time less
than one second. Maximum tip temperature 250 °C.
133-301
This plug-mounted stainless steel surface probe is ideal
for measuring metallic surfaces. A right-angled version is
also available, order code 133-046. Response time less
than one second. Maximum tip temperature 250 °C.
133-045
This FEP (plastic) penetration probe, for measuring
food temperatures, was originally designed for airlines
where safety is paramount. Response time less than
three seconds. Maximum tip temperature 250 °C.
133-155
*
www.servesafe.in
fax
+91 022 27656636
INDUSTRIAL THERMOMETERS
Thermapen™ Thermometer
with air, surface or penetration probe
one-handed operation
NEW!
auto-power on/off facility
foldaway stainless steel probe
lightweight, compact & easy to use
The Thermapen thermometer incorporates a large digital
display with a precise read-out over the range of -49.9
to 299.9 °C with a 0.1 °C resolution and an accuracy
of ±0.4 °C. The resolution can be switched to 1 °C, if
required, via a switch in the battery compartment. The
thermometer will power off automatically after ten minutes,
maximising battery life. This feature can be disabled if not
required. Both low battery (icon) and open circuit indication
are also displayed, when applicable. Each Thermapen is
powered by two lithium coin cell batteries with a minimum
life expectancy of 1500 hours.
The Thermapen thermometer probe, conveniently folds
back through 180 degrees into the side of the instrument
when not in use. The casing is washable and includes
'Biomaster' additive that reduces bacteria growth and the
ergonomic rubber seal minimises the risk of the ingress of
water, dust or food.
choice of probe styles
The Thermapen thermometer is also available with three alternative styles of probe; surface, air or penetration.
The fast response air probe is an invaluable tool in establishing the correct air temperature quickly in HVAC and
laboratory applications. The surface probe is particularly useful in determining the temperature of hot plates or pipe
temperatures etc. Please note the accuracy and speed of response will be dependant on whether the surface is flat
and heat transfer compound is used.
penetration probe
surface probe
air probe
This strong, versatile penetration
probe with a pointed, general
purpose tip is suitable for liquid and
semi-solid insertion.
This ribbon surface probe is ideal
for measuring the temperature
of a variety of flat surfaces, i.e.
hotplates, pipework, bearings, etc.
This fast response air probe is ideal
for measuring the air temperature in
laboratories and other temperature
sensitive working areas.
Ø8 x 95 mm
Ø3.3 x 95 mm
Ø3.3 x 95 mm
order code description
231-210 white Thermapen - penetration probe
231-212 white Thermapen - surface probe
231-214 white Thermapen - air probe
830-260 protective silicone boot
830-110 protective wallet
830-001 zip pouch
832-200 wall bracket
specification
Thermapen
range
-49.9 to 299.9 °C
resolution
0.1 °C or 1 °C - user selectable
accuracy
±0.4 °C (-49.9 to 199.9 °C) or ±1 °C
battery
2 x 3 volt CR2032 lithium coin cell
battery life
1500 hours
sensor type
K thermocouple
display
14.3 mm LCD
dimensions
19 x 47 x 153 mm
weight
97 grams
FREE traceable certificate of calibration included
*
Sales
+91 022 27666033 / 27664080
email
[email protected]
INDUSTRIAL THERMOMETERS
Bi-Metal Dial Thermometers
simple to use
dial probe thermometers
milk frothing dial thermometers
adjustment nut Z
These pocket-sized dial thermometers feature either a
Ø25 mm or Ø45 mm dial with a pointed Ø4 x 130 mm
stainless steel stem and are supplied with a probe cover.
Each dial thermometer is available in three scales. A
stainless steel mounting clip is available.
order code
800-811
800-812
800-813
800-801
800-802
800-803
830-220
description
range
Ø25 mm dial -40 to 70
Ø25 mm dial -10 to 110
Ø25 mm dial
0 to 250
Ø45 mm dial -40 to 70
Ø45 mm dial -10 to 110
Ø45 mm dial
0 to 250
Ø4 mm probe holder clip
°C
°C
°C
°C
°C
°C
The milk frothing dial thermometers incorporate
colour-coded zones that make them fast and simple to
use. Available with Ø25 mm dial x 130 mm probe or
Ø45 mm dial x 130 or 175 mm probe. Each thermometer
is supplied with a stainless steel jug mounting probe clip.
order code
800-810
800-820
800-800
description
Ø25 x 130 mm milk dial
Ø45 x 130 mm milk dial
Ø45 x 175 mm milk dial
waterproof dial thermometers
heavy duty dial probe thermometers
These waterproof dial thermometers feature a Ø45 mm
dial with 130 mm stem and indicate temperature over
the range of -10 to 110 °C.
These simple to use, heavy duty, 50 mm diameter dial
probe thermometers are reliable and accurate. The
dial thermometers feature a Ø6.35 x 300 mm pointed
stainless steel stem. Ideal for asphalt, blacktop, soil
and other heavy duty applications.
The dial face has a clear, graduated scale indicating
temperature in 1 °C divisions.
The thermometer is supplied with a green or red silicone
boot that helps protect the instrument against accidental
damage.
order code
800-833
800-834
description
waterproof dial - green boot
waterproof dial - red boot
Each thermometer incorporates a clear acrylic face
and a calibration adjustment screw, at rear of the dial.
Three temperature scales are available.
order code
800-060
800-120
800-250
description
range
dial thermometer -20 to 60 °C
dial thermometer
0 to 120 °C
dial thermometer
0 to 250 °C
*
www.servesafe.in
fax
+91 022 27656636
ideal for the HVAC industry
pipe surface thermometer
This easy to use surface pipe thermometer features a
Ø60 mm stainless steel dial and indicates temperature
over the range of 0 to 120 °C or 32 to 250 °F. The
Ø50 mm dial face has a clear, graduated scale indicating
temperature in 2 °C and 4 °F divisions.
Each thermometer is supplied with a wrap-around
stainless steel spring kit (53 mm long) for pipe mounting.
For larger pipes it is possible to attach the thermometer to
pipework using either tie-wraps or wire (not supplied).
order code
800-951
description
pipe thermometer
magnetic surface thermometer
This Ø60 mm stainless steel surface dial thermometer
incorporates a magnetic sensing pad for mounting on
ferrous metals and indicates temperature ranges 0 to
120 °C.
The Ø50 mm dial face has a clear, graduated scale
indicating temperature in 2 °C divisions.
order code
800-950
description
magnetic thermometer
budget pipe surface thermometer
hot water dial thermometer
This easy to use surface pipe thermometer features a
Ø60 mm nickel plated dial and indicates temperature
over the range of 0 to 120 °C.
This simple to use Ø45 mm dial probe thermometer is
reliable and accurate. The hot water dial thermometer
features a Ø4 x 300 mm pointed stainless steel stem.
The thermometer indicates temperature over the range
of -40 to 70 °C in 2 °C divisions.
The Ø50 mm dial face has a clear, graduated scale
indicating temperature in 2 °C divisions.
Each thermometer is supplied with a wrap-around spring
kit (53 mm long) for pipe mounting. For larger pipes it
is possible to attach the thermometer to pipework using
either tie-wraps or wire (not supplied).
order code
800-971
description
pipe thermometer
The dial thermometer is ideal for measuring water
temperatures and semi-solid materials in a wide variety
of industrial applications. Each thermometer is supplied
with a stainless steel mounting probe clip that can be
attached to the side of a water container or similar.
order code
800-990
description
Ø45 mm dial thermometer
*
Sales
+91 022 27666033 / 27664080
email
[email protected]
INDUSTRIAL THERMOMETERS
Bi-Metal Dial Thermometers
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement