Samsung RM40D Signage TV - LH40RMDPLGUR User manual

Samsung RM40D Signage TV - LH40RMDPLGUR User manual

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Manual
Samsung RM40D Signage TV - LH40RMDPLGUR User manual | Manualzz

SMART Signage TV

User Manual

RM40D RM48D

The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.

Recommended hours of use per day of this product is under 16 hours.

If the product is used for longer than 16 hours a day, the warranty may be void.

BN46-00439B-00

Table of contents

Before Using the Product

Copyright 6

Safety Precautions 7

Symbols 7

Cleaning 7

Storage 8

Electricity and Safety 8

Installation 9

Operation 11

Preparations

Checking the Components 15

Parts 17

Control Panel 17

Reverse Side

Anti-theft Lock

Remote Control

19

20

21

Before Installing the Product

(Installation Guide)

Tilting Angle and Rotation

23

23

Ventilation 23

Dimensions 24

Installing the Wall Mount

Installing the Wall Mount Kit

Wall Mount Kit Specifications

25

25

26

Connecting and Using a Source

Device

Before Connecting

Pre-connection Checkpoints

Connecting to a PC

Connection using the D-SUB cable

(Analogue type)

Connection Using an HDMI Cable

Connection Using an HDMI-DVI Cable

Connecting to a Video Device

Connection Using the AV Cable

Connection Using an HDMI-DVI Cable

Connection Using an HDMI Cable

Connecting to an Audio System

Connecting the Antenna

Connecting to a TV Viewing Card slot

To connect the CI CARD, follow these steps:

Initial Setup 33

Changing the Input source 33

Source List 33

31

32

32

29

29

30

30

27

28

28

31

27

27

27

Screen Adjustment

Picture Mode 34

If the input source is PC or HDMI1 (when a PC is connected), HDMI2 (when a PC is connected) 34

If the input source is TV, HDMI1, HDMI2 or AV 34

Backlight / Contrast / Brightness / Sharpness /

Colour / Tint (G/R) 35

Picture Size 36

Picture Size 36

Position 38

Zoom/Position 38

4:3 Screen Size 39

Resolution Select 39

Auto Adjustment 40

PC Screen Adjustment 41

PIP 42

PIP Settings 42

Advanced Settings 43

Dynamic Contrast 44

Black Tone 44

Flesh Tone 44

RGB Only Mode 44

Colour Space 44

White Balance 45

Gamma 45

Motion Lighting 45

Picture Options 46

Colour Tone 47

Colour Temp. 47

Digital Clean View 47

MPEG Noise Filter 47

HDMI Black Level 48

Film Mode 48

2

Table of contents

Dynamic Backlight 48

Picture Off 49

Reset Picture 49

Sound Adjustment

Sound Mode 50

Sound Effect 51

Speaker Settings 52

Additional Settings 53

DTV Audio Level 53

Dolby Digital Comp 53

Reset Sound 54

Broadcasting

Auto Tuning 55

Auto Tuning 55

Cable Search Option 56

Aerial 57

Channel List 58

Sorting 58

Mode 58

Schedule Manager 60

Edit Channel 61

Edit Favorites 63

Channel Settings 66

Country (Area) 66

Manual Tuning 66

Fine Tune 67

Transfer Channel List 67

Delete CAM Operator Profile 67

Subtitle 68

Subtitle 68

Primary Subtitle 68

Secondary Subtitle 68

Audio Options 69

Audio Language 69

Audio Format 69

Audio Description 69

Programme Rating Lock 70

Teletext Language 71

Teletext Language 71

Primary Teletext 71

Secondary Teletext 71

Common Interface 72

CI Menu 72

CAM video transcoding 72

Application Info 72

Channel Lock 73

Network

Network Status 74

Network Settings 74

Network Setting (Wireless) 75

WPS(PBC) 77

Soft AP (Wi-Fi Hotspot) 78

Wi-Fi Direct 79

AllShare Settings 80

Device Name 80

Applications

Source List 81

MagicInfo 82

Playing content from the internal memory or

USB 82

Playing PC or mobile content 82

Schedule 83

MagicInfo Express Content Creator

Using MagicInfo Express Content Creator 85

Managing templates 85

Managing schedules 85

3

Table of contents

Playing photos, videos and music

(Media Play)

Read the following before using media play with a USB device 86

Using a USB device

Menu items in the media content list page

88

89

Available buttons and features during photo playback 90

Available buttons and features during video playback 91

Available buttons and features during music playback 92

Supported Subtitle and Media play file formats 93

Subtitle 93

Supported image resolutions 93

Supported music file formats

Supported Video Formats

94

94

System

Setup 97

Initial settings (Setup) 97

Menu Language 99

Time 100

Clock 100

Sleep Timer 101

On Timer 101

Off Timer 103

Holiday Management 103

Eco Solution 104

Energy Saving 104

Eco Sensor 104

No Signal Power Off 105

Auto Power Off 105

Auto Protection Time 106

Screen Burn Protection 107

Pixel Shift 107

Timer 108

Immediate display 110

Side Grey 110

Ticker 111

Ticker 111

Source AutoSwitch Settings 112

Source AutoSwitch 112

General 113

Game Mode 113

Auto Power 113

Safety Lock 113

Button Lock 114

USB Auto Play Lock 114

Standby Control 114

Lamp Schedule 115

OSD Display 115

Change PIN 116

Clone Product 117

Reset System 117

Reset All 118

DivX® Video On Demand 118

Support

Software Update 119

Update now 119

Use Mode 119

Contact Samsung 120

Troubleshooting Guide

Requirements Before Contacting Samsung

Customer Service Centre

Testing the Product

Checking the Resolution and Frequency

Check the followings.

121

121

121

122

Q & A 128

4

Table of contents

Specifications

General 130

Power Consumption

Preset Timing Modes

132

133

Appendix

Contact SAMSUNG WORLD WIDE 135

Responsibility for the Pay Service

(Cost to Customers)

Not a product defect

144

144

A Product damage caused by customer's fault 144

Others 144

WEEE 145

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment) 145

Correct disposal of batteries in this product 145

Optimum Picture Quality and Afterimage

Burn-in Prevention

Optimum Picture Quality

Prevention of Afterimage Burn-in

146

146

146

Licence 148

Terminology 149

5

Chapter 01

Before Using the Product

Copyright

The contents of this manual are subject to change without notice to improve quality.

© 2014 Samsung Electronics

Samsung Electronics owns the copyright for this manual.

Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.

Microsoft, Windows are registered trademarks of Microsoft Corporation.

VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.

Ownership of all other trademarks is attributed to their due owner.

• An administration fee may be charged if either

(a) an engineer is called out at your request and there is no defect in the product

(i.e. where you have failed to read this user manual).

(b) you bring the unit to a repair centre and there is no defect in the product

(i.e. where you have failed to read this user manual).

• The amount of such administration charge will be advised to you before any work or home visit is carried out.

6

Safety Precautions

Caution

RISK OF ELECTRIC SHOCK DO NOT OPEN

Caution : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. (OR BACK)

THERE ARE NO USER SERVICEABLE PARTS INSIDE.

REFER ALL SERVICING TO QUALIFIED PERSONNEL.

This symbol indicates that high voltage is present inside.

It is dangerous to make any kind of contact with any internal part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

Symbols

Warning

A serious or fatal injury may result if instructions are not followed.

Caution

Personal injury or damage to properties may result if instructions are not followed.

Activities marked by this symbol are prohibited.

Instructions marked by this symbol must be followed.

Cleaning

― Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.

― Take the following steps when cleaning.

― The following images are for reference only. Real-life situations may differ from what is shown in the images.

1 Power off the product and computer.

2 Disconnect the power cord from the product.

― Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result.

3 Wipe the product with a clean, soft and dry cloth.

• Do not use detergents that contain alcohol, solvent or surface-active agents.

!

• Do not spray water or detergent directly on the product.

4 Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the product.

5

Connect the power cord to the product when cleaning is finished.

6

Power on the product and computer.

7

Storage

Due to the characteristics of high-glossy products, using a UV humidifier nearby may create whitecoloured stains on the product.

― Contact Customer Service Centre if the inside of the product needs cleaning (service fee will be charged).

Electricity and Safety

― The following images are for reference only. Real-life situations may differ from what is shown in the images.

Warning

Do not use a damaged power cord or plug, or a loose power socket.

• An electric shock or fire may result.

!

Do not use multiple products with a single power socket.

• Overheated power sockets may cause a fire.

Do not touch the power plug with wet hands. Otherwise, an electric shock may result.

!

Insert the power plug all the way in so it is not loose.

• An unsecure connection may cause a fire.

!

Connect the power plug to a grounded power socket (type 1 insulated devices only).

• An electric shock or injury may result.

Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy object.

• Damage to the cord may result in a fire or electric shock.

Do not place the power cord or product near heat sources.

• A fire or electric shock may result.

Clean any dust around the pins of the power plug or the power socket with a dry cloth.

• A fire may result.

8

Caution

!

!

!

Do not disconnect the power cord while the product is being used.

• The product may become damaged by an electric shock.

Only use the power cord provided with your product by Samsung. Do not use the power cord with other products.

• A fire or electric shock may result.

Keep the power socket where the power cord is connected unobstructed.

• The power cord must be disconnected to cut off power to the product when an issue occurs.

• Note that the product is not completely powered down by using only the power button on the remote.

Hold the plug when disconnecting the power cord from the power socket.

• An electric shock or fire may result.

!

Installation

Warning

DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF

THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.

• A fire may result.

Have a technician install the wall-mount hanger.

• Installation by an unqualified person can result in an injury.

• Only use approved cabinets.

Do not install the product in poorly ventilated spaces such as a bookcase or closet.

• An increased internal temperature may cause a fire.

Install the product at least 10 cm away from the wall to allow ventilation.

• An increased internal temperature may cause a fire.

!

Keep the plastic packaging out of the reach of children.

• Children may suffocate.

!

9

!

!

!

Bend and keep part of the outdoor TV antenna cable hanging downwards

(the part inside the room) to prevent rainwater from entering the product.

• If rainwater enters the product, a fire or electric shock can occur.

When using an outdoor antenna, be sure to install the antenna away from nearby power lines to prevent the antenna from collapsing onto them in strong winds.

• A collapsed antenna can cause an electric shock or injury.

Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)

• The product may fall and become damaged and/or cause an injury.

• Using the product in an area with excess vibration may damage the product or cause a fire.

Do not install the product in a vehicle or a place exposed to dust, moisture

(water drips, etc.), oil, or smoke.

• A fire or electric shock may result.

Do not expose the product to direct sunlight, heat, or a hot object such as a stove.

• The product lifespan may be reduced or a fire may result.

Do not install the product within the reach of young children.

• The product may fall and injure children.

• As the front is heavy, install the product on a flat and stable surface.

Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a kitchen or near a kitchen counter.

10

Caution

!

Do not drop the product while moving.

• Product failure or personal injury may result.

Do not set down the product on its front.

• The screen may become damaged.

When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of the product is not protruding.

• The product may fall and become damaged and/or cause an injury.

• Install the product only on cabinets or shelves of the right size.

Set down the product gently.

• Product failure or personal injury may result.

!

!

!

!

SAMSUNG

Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical substances, extreme temperatures or a significant presence of moisture, or a place where the product will operate continuously for an extended period of time) may seriously affect its performance.

• Be sure to consult Samsung Customer Service Centre if you want to install the product at such a place.

Operation

Warning

There is a high voltage inside the product. Never disassemble, repair or modify the product yourself.

• A fire or electric shock may result.

• Contact Samsung Customer Service Centre for repairs.

Before moving the product, turn off the power switch and disconnect the power cord, antenna cable and all other connected cables.

• Damage to the cord may result in a fire or electric shock.

If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord immediately and contact Samsung Customer

Service Centre.

• An electric shock or fire may result.

Do not let children hang from the product or climb on top of it.

• Children may become injured or seriously harmed.

If the product is dropped or the outer case is damaged, turn off the power switch and disconnect the power cord. Then contact Samsung Customer

Service Centre.

• Continued use can result in a fire or electric shock.

11

!

!

!

Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.

• The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a serious injury.

During a lightning or thunderstorm, remove the power cable and do not touch the antenna cable.

• A fire or electric shock may result.

!

Do not drop objects on the product or apply impact.

• A fire or electric shock may result.

100

GAS

Do not move the product by pulling the power cord or any cable.

• Product failure, an electric shock or fire may result from a damaged cable.

If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area immediately.

• Sparks can cause an explosion or fire.

Do not lift or move the product by pulling the power cord or any cable.

• Product failure, an electric shock or fire may result from a damaged cable.

Do not use or keep combustible spray or an inflammable substance near the product.

• An explosion or fire may result.

Ensure the vents are not blocked by tablecloths or curtains.

• An increased internal temperature may cause a fire.

Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper, matches, etc) into the product (via the vent or input/ output ports, etc).

• Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product.

Then contact Samsung Customer Service Centre.

• Product failure, an electric shock or fire may result.

Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the product.

• Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product.

Then contact Samsung Customer Service Centre.

• Product failure, an electric shock or fire may result.

12

!

!

Caution

!

!

-_-

Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels.

• Activate power-saving mode or a moving-picture screen saver if you will not be using the product for an extended period of time.

Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc).

• Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.

Use the product at the recommended resolution and frequency.

• Your eyesight may deteriorate.

!

!

Do not hold the product upside-down or move it by holding the stand.

• The product may fall and become damaged or cause an injury.

!

Looking at the screen too close for an extended period of time can deteriorate your eyesight.

Do not use humidifiers or stoves around the product.

• A fire or electric shock may result.

Rest your eyes for more than 5 minutes for every 1 hour of product use.

• Eye fatigue will be relieved.

Do not touch the screen when the product has been turned on for an extended period of time as it will become hot.

Store small accessories out of the reach of children.

Exercise caution when adjusting the product angle or stand height.

• Your hand or finger may get stuck and injured.

• Tilting the product at an excessive angle may cause the product to fall and an injury may result.

Do not place heavy objects on the product.

• Product failure or personal injury may result.

When using headphones or earphones, do not turn the volume too high.

• Having the sound too loud may damage your hearing.

13

!

!

Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach.

• If children have had the battery in their mouths, consult your doctor immediately.

When replacing the battery, insert it with the right polarity (+, -).

• Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.

Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time.

• Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.

The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.

• The customer can return used or rechargeable batteries to a nearby public recycling centre or to a store selling the same type of the battery or rechargeable battery.

14

Chapter 02

Preparations

Checking the Components

Contact the vendor where you purchased the product if any components are missing.

The appearance of the components and items sold separately may differ from the image shown.

Components

― Components may differ in different locations.

Quick setup guide

Warranty card

(Not available in some locations)

Regulatory guide

Batteries

(Not available in some locations)

Remote Control Power cord

Stand base Stand neck

User manual / MagicInfo Express

Content Creator USB

Mini Wall-mount Kit

15

The following items can be purchased at your nearest retailer.

Items sold separately

HDMI cable HDMI-DVI cable Video cable Audio cable RCA stereo cable

Stereo cable D-SUB cable

16

Parts

Control Panel

Panel Key

Speaker

POWER

Remote sensor

― The colour and shape of parts may differ from what is shown.

Specifications are subject to change without notice to improve quality.

Panel Key

Buttons Description

Power on the product.

If you press the button when the product is turned on, the control menu will be displayed.

― To exit the OSD menu, press and hold the panel key for at least one second.

Move to the upper or lower menu. You can also adjust the value of an option.

Change the channel in TV mode.

Remote sensor

Move to the left or right menu.

― You can adjust the volume by moving the panel key left or right when the control menu is not displayed.

Press a button on the remote control pointing at the sensor on the front of the product to perform the corresponding function.

― Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.

Use the remote control within 7 m to 10 m from the sensor on the product at an angle of 30 from the left and right.

― Store used batteries out of reach of children and recycle.

― Do not use a new and used battery together. Replace both batteries at the same time.

― Remove batteries when the remote control is not to be used for an extended period of time.

17

― If you press the button on the panel key when the product is turned on, the control menu will be displayed.

Control menu

Buttons

Return

Source

Menu

MagicInfo

Power off

Return

Description

Select the connected input source.

Move the panel key right to select Source in the control menu.

When the list of input sources is displayed, move the panel key up or down to select the desired input source. Next, press the panel key.

Display the OSD menu.

Move the panel key left to select Menu in the control menu. The OSD control screen will appear. Move the panel key right to select the desired menu.

You can select a sub-menu item by moving the panel key up, down, left, or right.

To change settings, select the desired menu and press the panel key.

Enter MagicInfo mode.

Move the panel key up to select MagicInfo in the control menu.

Power off the product.

Move the panel key down to select Power off in the control menu.

Next, press the panel key.

Exit the control menu.

18

Reverse Side

― The colour and shape of parts may differ from what is shown.

Specifications are subject to change without notice to improve quality.

COMMON

INTERFACE

PC

AUDIO

IN

PC IN

HDMI IN 2

(DVI)

HDMI IN 1

(STB)

USB

(5V 0.5A)

/ CLONING

ANT IN

AIR/CABLE

AUDIO

OUT

RS232C IN

AV IN

PC

AUDIO

IN

PC IN

Port

COMMON INTERFACE

HDMI IN 2 (DVI)

HDMI IN 1 (STB)

USB (5V 0.5A) / CLONING

ANT IN AIR/CABLE

AUDIO OUT

RS232C IN

AV IN VIDEO / L-AUDIO-R

PC AUDIO IN

PC IN

Description

Connect to a CI card.

Connects to a source device using a HDMI cable or HDMI-DVI cable.

Connects to a source device using a HDMI cable or HDMI-DVI cable.

Connect to a USB memory device.

Connect to an antenna cable.

Connects to the audio of a source device.

Used for service purposes.

Connect to an external device using a video or Audio cable.

Receives sound from a PC via an audio cable.

Connects to a source device using a D-SUB cable.

19

Anti-theft Lock

― An anti-theft lock allows you to use the product securely even in public places.

― The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.

― The following images are for reference only. Real-life situations may differ from what is shown in the images.

To lock an anti-theft locking device:

1

Fix the cable of your anti-theft locking device to a heavy object such as a desk.

2

Put one end of the cable through the loop on the other end.

3

Insert the locking device into the anti-theft lock slot at the back of the product.

4

Lock the locking device.

An anti-theft locking device can be purchased separately.

Refer to the user guide provided with your anti-theft locking device for details.

Anti-theft locking devices can be purchased at electronics retailers or online.

20

Remote Control

― Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.

― A button without a description in the image below is not supported on the product.

Turns the product On/Off.

Alternately selects Teletext, Double or Mix.

Adjust the volume.

Display channel list on the screen.

Display the main on-screen menu.

TTX/MIX

GUIDE

CH LIST

HOME CONTENT

Display and select available video sources.

Have direct access to channels.

Electronic Programme Guide (EPG) display.

Cut off the sound temporarily.

Change channels.

Swich to the MagicInfo Screen.

Swich to the MagicInfo Screen.

Remote control button functions may differ for different products.

21

CLOCK

Quickly select frequently used functions.

Select on-screen menu items and change menu values.

Return to the previous menu.

Configure the subtitle and audio description options.

Not Available.

A

ALARM

B C

SUBT.

D

Press to display information on the TV screen.

CLOCK: When you press INFO key in standby mode, TV screen displays the time.

Exit the menu.

Use TTX secondary function.

Play photos, videos or music.

Remote control button functions may differ for different products.

To place batteries in the remote control

― Insert 2 AAA batteries, making sure to align the positive and negative polarities correctly.

22

Before Installing the Product

(Installation Guide)

15 ˚

To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

• Ensure that an authorized installation company installs the wall mount.

• Otherwise, it may fall and cause personal injury.

• Make sure to install the specified wall mount.

Tilting Angle and Rotation

― Contact Samsung Customer Service Centre for further details.

• The product can be tilted at a maximum angle of 15˚ from a perpendicular wall surface.

• To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.

Ventilation

Installation on a Perpendicular Wall

A Minimum 40 mm

B Ambient temperature: Under 35 C

• When installing the product on a perpendicular wall, allow at least 40 mm of space between the product and wall surface for ventilation and ensure that the ambient A temperature is kept below 35 C.

A

B

Figure 1.1 Side view

23

B

A

E

C

Figure 1.2 Side view

Dimensions

2

1

Figure 1.3 Side view

D

4

3

D

Installation on an Indented Wall

― Contact Samsung Customer Service Centre for further details.

Plane view

A Minimum 40 mm

B Minimum 70 mm

C Minimum 50 mm

D Minimum 50 mm

E Ambient temperature: Under 35 C

― When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 C.

5

Model name

1

906.6 (35.69)

1 2

887.6 (34.94)

2 3

500.2 (19.69)

3 4

532.9 (20.98)

4 5

Unit: mm (inches)

65.1 (2.56) RM40D

RM48D 1075.1 (42.33) 1056.1 (41.58) 594.9 (23.42) 627.6 (24.71) 65.5 (2.58)

― All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice.

Refer to the dimensions prior to performing installation of your product. Not responsible for typographical or printed errors.

24

Installing the Wall Mount

Installing the Wall Mount Kit

The wall mount kit allows you to mount the product on the wall.

For detailed information on installing the wall mount, see the instructions provided with the wall mount.

We recommend you contact a technician for assistance when installing the wall mount bracket.

Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.

25

Wall Mount Kit Specifications

― Install your wall mount on a solid wall perpendicular to the floor. Before attaching the wall mount to surfaces other than plaster board, please contact your nearest dealer for additional information.

If you install the product on a slanted wall, it may fall and result in severe personal injury.

• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.

• Do not use screws that are longer than the standard length or do not comply with the VESA standard screw specifications. Screws that are too long may cause damage to the inside of the product.

• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on the wall mount specifications.

• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury.

Samsung is not liable for these kinds of accidents.

• Samsung is not liable for product damage or personal injury when non-specified wall mount is used or the consumer fails to follow the product installation instructions.

• Do not mount the product at more than a 15 degree tilt.

• Always have two people mount the product on a wall.

• Standard dimensions for wall mount kits are shown in the table below.

Unit: mm (inches)

Model name Screw hole specs

(A * B) in millimeters

Standard Screw Quantity

RM40D 200 × 200 (7.87 × 7.87)

M8 / L14~16 4

RM48D 400 × 400 (15.75 × 15.75)

― Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.

26

Chapter 03

Connecting and Using a Source Device

Before Connecting

Pre-connection Checkpoints

― Before connecting a source device, read the user manual provided with it.

The number and locations of ports on source devices may differ from device to device.

― Do not connect the power cable until all connections are completed.

Connecting the power cable during connection may damage the product.

― Connect the sound ports correctly: left = white and right = red.

― Check the types of ports at the back of the product you want to connect.

Connecting to a PC

• Do not connect the power cable before connecting all other cables.

Ensure you connect a source device first before connecting the power cable.

• A PC can be connected to the product in a variety of ways.

Select a connection method suitable for your PC.

― Connecting parts may differ in different products.

Connection using the D-SUB cable (Analogue type)

PC IN

PC AUDIO IN

27

Connection Using an HDMI Cable

HDMI IN 1 (STB), HDMI IN 2 (DVI)

Connection Using an HDMI-DVI Cable

― When you connect a PC to the product using an HDMI-DVI cable, set Edit Name to DVI PC to access video and audio content stored on the PC.

HDMI IN 1 (STB), HDMI IN 2 (DVI)

PC AUDIO IN

28

Connecting to a Video Device

• Do not connect the power cable before connecting all other cables.

Ensure you connect a source device first before connecting the power cable.

• You can connect a video device to the product using a cable.

― Connecting parts may differ in different products.

― Press the SOURCE button on the remote control to change the source.

Connection Using the AV Cable

AV IN / VIDEO

AV IN / L-AUDIO-R

29

Connection Using an HDMI-DVI Cable

― Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. To resolve this, additionally connect an audio cable to the audio ports on the product and video device.

When you connect a video device to the product using an HDMI-DVI cable, set Edit Name to DVI

Devices to access video and audio content stored on the video device.

― Supported resolutions include 1080p (50/60Hz), 720p (50/60Hz), 480p, and 576p.

HDMI IN 1 (STB), HDMI IN 2 (DVI)

Connection Using an HDMI Cable

Using an HDMI cable (up to 1080p)

• For better picture and audio quality, connect to a digital device using an HDMI cable.

• An HDMI cable supports digital video and audio signals, and does not require an audio cable.

• The picture may not display normally (if at all) or the audio may not work if an external device that uses an older version of HDMI mode is connected to the product. If such a problem occurs, ask the manufacturer of the external device about the HDMI version and, if out of date, request an upgrade.

• Be sure to use an HDMI cable with a thickness of 14 mm or less.

• Be sure to purchase a certified HDMI cable. Otherwise, the picture may not display or a connection error may occur.

• A basic high-speed HDMI cable or one with ethernet is recommended.

This product does not support the ethernet function via HDMI.

PC AUDIO IN

HDMI IN 1 (STB), HDMI IN 2 (DVI)

30

Connecting to an Audio System

― Connecting parts may differ in different products.

AUDIO OUT

Connecting the Antenna

― Connecting parts may differ in different products.

― When the product is powered on for the first time, basic settings are configured automatically.

Take extra care to ensure the wires inside the antenna cable are not bent.

ANT IN

AIR / CABLE

31

Connecting to a TV Viewing Card slot

To connect the CI CARD, follow these steps:

― CI card slots are available, depending on the model.

Using the “CI or CI+ CARD”

To watch paid channels, the “CI or CI+ CARD” must be inserted.

― Turn the TV off to connect or disconnect a CI card.

• If you don’t insert the “CI or CI+ CARD”, some channels will display the message “Scrambled Signal”.

• The pairing information containing a telephone number, the “CI or CI+ CARD” ID the Host ID and other information will be displayed in about 2~3 minutes. If an error message is displayed, please contact your service provider.

• When the configuration of channel information has finished, the message “Updating Completed” is displayed, indicating the channel list is updated.

― You must obtain a “CI or CI+ CARD” from a local cable service provider.

― When removing the “CI or CI+ CARD”, carefully pull it out with your hands since dropping the “CI or CI+ CARD” may cause damage to it.

― Insert the “CI or CI+ CARD” in the direction marked on the card.

― The location of the COMMON INTERFACE slot may be different depending on the model.

― “CI or CI+ CARD” is not supported in some countries and regions; check with your authorized dealer.

― If you have any problems, please contact a service provider.

― Insert the “CI or CI+ CARD” that supports the current aerial settings. The screen will be distorted or will not be seen.

32

Initial Setup

After powering on the product for the first time, configure basic settings such as the language, channel and time.

Language → Regional Settings → Channel Source → ( Auto Tuning does not appear if Set-top box or No TV(Signage Only) is selected.) → Network Settings → Clock → Auto Power Off → Setup Complete!

― Refer to

page 97 for details about the

Setup .

Changing the Input source

Source List

MENU m → Applications → Source List → ENTER E

Source

TV HDMI1 HDMI2 AV PC USB

Source allows you to select a variety of sources and change source device names.

You can display the screen of a source device connected to the product. Select a source from source list to display the screen of the selected source.

― The input source can also be changed by using the SOURCE button on the remote control.

― The screen may not display correctly if an incorrect source is selected for the source device you want to convert to.

― To view detailed information about connected source devices, press the TOOLS button from the Source page.

― Refer to

page 81 for details about the

Source List .

The displayed image may differ depending on the model.

33

Chapter 04

Screen Adjustment

Configure the Picture settings ( Backlight , Colour Tone , etc.).

The layout of the Picture menu options may vary depending on the product.

Picture Mode

MENU m → Picture → Picture Mode → ENTER E

Select a picture mode ( Picture Mode ) suitable for the environment where the product will be used.

Different Picture Mode options are displayed depending on the current input source.

Picture

Picture Mode

· Backlight

· Contrast

· Brightness

· Sharpness

· Colour

· Tint (G/R) G50

Information

55

100

45

50

50

R50

If the input source is PC or HDMI1 (when a PC is connected), HDMI2

(when a PC is connected)

• Information : This mode reduces eye fatigue and is suitable for displaying information to the public.

• Advertisement : This mode is suitable for displaying video content and indoor/outdoor advertisements.

― These options can be selected only when Edit Name is set to PC .

(SOURCE → Source → TOOLS → Edit Name → ENTER E)

If the input source is TV, HDMI1, HDMI2 or AV

• Dynamic : This mode is suitable when the ambient light is bright.

• Standard : This mode is generally suitable for any environment.

• Movie : This mode reduces eye fatigue.

The displayed image may differ depending on the model.

34

Backlight / Contrast / Brightness /

Sharpness / Colour / Tint (G/R)

MENU m → Picture → ENTER E

Picture

Picture Mode

· Backlight

· Contrast

· Brightness

· Sharpness

· Colour

· Tint (G/R) G50

Standard

55

100

45

50

50

R50

Your product has several options for adjusting picture quality.

Input source

PC , HDMI1 (when a PC is connected),

HDMI2 (when a PC is connected)

Picture Mode

Information , Advertisement

AV , HDMI1 , HDMI2 Dynamic , Standard , Movie

Adjustable options

Backlight / Contrast / Brightness /

Sharpness

Backlight / Contrast / Brightness /

Sharpness / Colour / Tint (G/R)

TV Dynamic , Standard , Movie Backlight / Contrast / Brightness /

Sharpness / Colour

― When you make changes to Backlight , Contrast , Brightness , Sharpness , Colour or Tint (G/R) , the OSD will be adjusted accordingly.

― You can adjust and store settings for each external device you have connected to an input on the product.

― Lowering picture brightness reduces power consumption.

The displayed image may differ depending on the model.

35

Picture Size

MENU m → Picture → Picture Size → ENTER E

Picture Size

Picture Size

· Position

· 4:3 Screen Size

Resolution Select

16:9

The displayed image may differ depending on the model.

choose size and aspect ratio picture displayed on screen.

Picture Size

― Different Screen Adjustment options are displayed depending on the current input source.

• Auto Wide : Automatically adjusts the picture size to the 16:9 aspect ratios.

• 16:9 : Sets the picture to 16:9 wide mode.

• Zoom1 : Use for moderate magnification. Cuts off the top and sides.

• Zoom2 : Use for a stronger magnification.

• Smart View 1 : Reduces the 16:9 picture by 50%.

― Smart View 1 is enabled only in HDMI1 , HDMI2 mode.

• Smart View 2 : Reduces the 16:9 picture by 25%.

― Smart View 2 is enabled only in HDMI1 , HDMI2 mode.

• Wide Fit : Enlarges the aspect ratio of the picture to fit the entire screen.

• 4:3 : Sets the picture to basic 4:3 mode.

― Do not set your product to 4:3 format for a long time.

The borders displayed on the left and right, or top and bottom of the screen may cause image retention (screen burn) which is not covered by the warranty.

• Screen Fit : Displays the full image without any cut-off when HDMI1 , HDMI2 (720p / 1080i / 1080p) signals are inputted.

• Original ratio : If the input source is PC or HDMI1 (PC connection), HDMI2 (PC connection) the video will display in the original aspect ratio.

• Custom : Changes the resolution to suit the user's preferences.

― Not available on analogue TVs.

36

Picture Sizes available by Input Source.

Input Source

ATV

DTV (1080i)

AV (480i, 480p)

HDMI1 HDMI2 (720p, 1080i, 1080p)

HDMI1 HDMI2 (480i, 480p)

PC , HDMI1 (when a PC is connected), HDMI2 (when a PC is connected)

Picture Size

Auto Wide , 16:9 , Zoom1 , Zoom2 , 4:3

16:9 , Smart View 2 , Wide Fit , 4:3 , Screen Fit

Auto Wide , 16:9 , Zoom1 , Zoom2 , 4:3 , Custom

16:9 , Smart View 1 , Smart View 2 , Wide Fit , 4:3 , Screen Fit ,

Custom

16:9 , Zoom1 , Zoom2 , Smart View 1 , Smart View 2 , 4:3 ,

Custom

16:9 , 4:3 , Original ratio

37

Position

Picture Size

Picture Size

·

Position

· 4:3 Screen Size

Resolution Select

Zoom1

The displayed image may differ depending on the model.

Zoom/Position

Picture Size

Picture Size

·

Zoom/Position

· 4:3 Screen Size

Resolution Select

Custom

The displayed image may differ depending on the model.

Adjusts the picture position. Position is only available if Picture Size is set to Zoom1 , Zoom2 , Wide Fit or Screen Fit .

― To use the Position function after selecting Zoom1 , Zoom2 , Wide Fit or Screen Fit , follow these steps.

1

Press the button to select Position . Press the E button.

2

Press the or button to move the picture up or down.

3

Press the E button.

― If you want to reset the picture to its original position, select Reset in the Position screen.

― The picture will be set to its default position.

Adjusts the picture zoom and position. This option is available when the input source is set to HDMI1 , HDMI2 (1080i/1080p) or

AV (1080i/1080p). Picture Size must be set to Custom for the option to be available.

1

Press the button to select Zoom/Position . Press the E button.

2

Select the Zoom or Position . Press the E button.

3

Press the / / / button to move the picture.

4 Press the E button.

― If you want to reset the picture to its original position, select Reset in the Zoom/Position screen.

― The picture will be set to its default position.

38

4:3 Screen Size

Picture Size

Picture Size

· Zoom/Position

·

4:3 Screen Size

Resolution Select

Custom

16:9

The displayed image may differ depending on the model.

Resolution Select

Picture Size

Picture Size

· Zoom/Position

· 4:3 Screen Size

Resolution Select

Custom

16:9

Off

Available in PC mode only.

The displayed image may differ depending on the model.

Available only when picture size is set to Auto Wide . You can determine the desired picture size at the 4:3 WSS (Wide Screen

Service) size or the original size. Each European country requires different picture size.

If the picture is not normal even when the resolution of the graphics card is one of the following, you can optimize the picture quality by selecting the same resolution for the product as the PC using this menu.

Available resolutions: Off / 1024x768 / 1280x768 / 1360x768 / 1366x768

39

Auto Adjustment

MENU m → Picture → Auto Adjustment → ENTER E

Picture

Auto Adjustment

Available in PC mode only.

The displayed image may differ depending on the model.

Adjust frequency values/positions and fine tune the settings automatically

40

PC Screen Adjustment

MENU m → Picture → PC Screen Adjustment → ENTER E

PC Screen Adjustment

Coarse

Fine

Position

Image Reset

50

0

The displayed image may differ depending on the model.

• Coarse / Fine

Removes or reduces picture noise.

If the noise is not removed by Fine-tuning alone, use the Coarse function to adjust the frequency as best as possible

( Coarse ) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned with the centre of screen.

• Position

To adjust the PC’s screen position if it is not centred or does not fit the product screen.

Press the or button to adjust the Vertical Position. Press the or button to adjust the Horizontal Position.

• Image Reset

Resets the image to the default settings.

41

PIP

MENU m → Picture → PIP → ENTER E

Picture

PIP

The displayed image may differ depending on the model.

For PIP sound, refer to the Sound Select instructions.

If you turn the product off while watching in the PIP mode, PIP mode will remain after power

Off/On.

PIP Settings

The picture from the external video source will be in the main screen and the picture from the product will be in the PIP subpicture screen.

Main picture

AV , TV

Sub picture

PC , HDMI1 , HDMI2

HDMI1 , HDMI2 PC , TV , AV

PC TV , AV , HDMI1 , HDMI2

• PIP ( Off / On ): Activate or deactivate the PIP function.

• Source : You can select a source of the sub picture.

• Antenna ( Air / Cable ): Select either Air or Cable as the input source for the sub-screen.

― This option is enabled if the secondary display is set to TV .

• Channel : Select the channel for the sub-screen.

― This option is enabled if the secondary display is set to TV .

• Size ( , , , , , ): Select a size for the subpicture.

• Position ( , , , ): Select a position for the sub-picture.

― In Double ( , , ) mode, you cannot select Position .

• Sound Select ( Main / Sub ): You can choose to listen to the sound from the Main picture or the Sub picture.

42

Advanced Settings

MENU m → Picture → Advanced Settings → ENTER E

Advanced Settings

Dynamic Contrast

Black Tone

Flesh Tone

RGB Only Mode

Colour Space

White Balance

Gamma

Medium

Off

0

Off

Native

0

The displayed image may differ depending on the model.

Input Source

PC , HDMI1 (when a PC is connected), HDMI2 (when a

PC is connected)

Picture Mode

Information ,

Advertisement

TV , HDMI1 , HDMI2 , AV Dynamic

Standard

Movie

Advanced Settings

White Balance / Gamma

Not available.

Dynamic Contrast / Black Tone / Flesh Tone / RGB

Only Mode / Colour Space / White Balance / Gamma /

Motion Lighting

Dynamic Contrast / Black Tone / Flesh Tone / RGB Only

Mode / Colour Space / White Balance / Gamma

43

Advanced Settings

Dynamic Contrast

Black Tone

Flesh Tone

RGB Only Mode

Colour Space

White Balance

Gamma

Medium

Off

0

Off

Native

0

The displayed image may differ depending on the model.

Dynamic Contrast

Adjust the screen contrast.

• Off / Low / Medium / High

Black Tone

Select the black level to adjust the screen depth.

• Off / Dark / Darker / Darkest

Flesh Tone

Emphasize pink Flesh Tone .

RGB Only Mode

Displays the Red , Green and Blue colour for making fine adjustments to the hue and saturation.

• Off / Red / Green / Blue

Colour Space

Adjusts the range and variety of colours (the colour space) available to create images.

• Auto / Native

44

Advanced Settings

White Balance

Gamma

Motion Lighting

The displayed image may differ depending on the model.

0

Off

White Balance

Adjust the colour temperature for a more natural picture.

2 Point

• R-Offset / G-Offset / B-Offset : Adjust each colour’s (red, green, blue) darkness.

• R-Gain / G-Gain / B-Gain : Adjust each colour’s (red, green, blue) brightness.

• Reset : Resets the White Balance to its default settings.

Gamma

Adjust the primary colour intensity.

Motion Lighting

Reduces power consumption by reducing screen brightness when the picture on the screen is in motion.

• Off / On

45

Picture Options

MENU m → Picture → Picture Options → ENTER E

Picture Options

Colour Tone

Colour Temp.

Digital Clean View

MPEG Noise Filter

HDMI Black Level

Film Mode

Dynamic Backlight

Off

10000K

Off

Off

Normal

Off

Off

The displayed image may differ depending on the model.

Select an option using the and arrow keys, and the press E.

Use the arrow keys to change the setting, and then press E.

Input source Picture Mode Picture Options

PC , HDMI1 (when a PC is connected), HDMI2 (when a

PC is connected)

Information , Advertisement Colour Tone / Dynamic Backlight

HDMI1 , HDMI2 Dynamic , Standard , Movie

TV , HDMI1 (1080i), HDMI2

(1080i), AV

Dynamic , Standard , Movie

Colour Tone / Digital Clean View / MPEG Noise Filter /

HDMI Black Level / Dynamic Backlight

Colour Tone / Digital Clean View / MPEG Noise Filter /

Film Mode / Dynamic Backlight

46

Picture Options

Colour Tone

Colour Temp.

Digital Clean View

MPEG Noise Filter

Off

10000K

Off

Off

The displayed image may differ depending on the model.

Colour Tone

If the input source is PC , HDMI1 (PC connection), HDMI2 (PC connection).

• Off / Cool / Standard / Warm

If the input source is AV , HDMI1 , HDMI2 or TV .

• Off / Cool / Standard / Warm1 / Warm2

― Warm1 or Warm2 will be deactivated when the Picture Mode is Dynamic .

― Settings can be adjusted and stored for each external device connected to an input on the product.

Colour Temp.

Adjust the colour temperature ( Red / Green / Blue ). (Range: 3000K–15000K)

― This option is available when Colour Tone is set to Off .

Digital Clean View

If the broadcast signal received by your product is weak, you can activate the Digital Clean View feature to reduce any static and ghosting that may appear on the screen.

• Off / Low / Medium / High / Auto / Auto Visualisation

― Auto Visualisation : When changing analogue channels, displays signal strength.

― When the signal is weak, try all the options until the the product displays the best picture.

MPEG Noise Filter

Reduces MPEG noise to provide improved picture quality.

• Off / Low / Medium / High / Auto

47

Picture Options

HDMI Black Level

Film Mode

Dynamic Backlight

Normal

Off

Off

The displayed image may differ depending on the model.

HDMI Black Level

Selects the black level on the screen to adjust the screen depth.

• Normal / Low

― Available only in HDMI1 (PC connection), HDMI2 (PC connection) mode (AV Timing : 480p, 576p, 720p, 1080i, 1080p).

Film Mode

This mode is suitable to view movies.

Sets the product to automatically sense and process film signals from all sources and adjust the picture for optimum quality.

• Off / Auto1 / Auto2

― Available in TV , AV .

Dynamic Backlight

Automatically adjust the backlight to provide the best possible screen contrast under the current conditions.

• Off / On

48

Picture Off

MENU m → Picture → Picture Off → ENTER E

Picture

Picture Off

The displayed image may differ depending on the model.

Reset Picture

MENU m → Picture → Reset Picture → ENTER E

Picture

Reset Picture

The displayed image may differ depending on the model.

Selecting Picture Off switches off the screen. The volume is not disabled.

To switch the screen on, press any button other than the volume button.

Resets your current picture mode to its default settings.

49

Chapter 05

Sound Adjustment

Configure the sound ( Sound ) settings for the product.

Sound Mode

MENU m → Sound → Sound Mode → ENTER E

Sound

Sound Mode

Sound Effect

Speaker Settings

Additional Settings

Reset Sound

Standard

The displayed image may differ depending on the model.

You can select a sound mode to suit your personal preferences.

• Standard : Selects the normal sound mode.

• Music : Emphasizes music over voices.

• Movie : Provides the best sound for movies.

• Clear Voice : Emphasizes voices over other sounds.

• Amplify : Increase the intensity of high-frequency sound to allow a better listening experience for the hearing impaired.

― If Speaker Select is set to External , Sound Mode is disabled.

50

Sound Effect

MENU m → Sound → Sound Effect → ENTER E

Sound

Sound Effect

The displayed image may differ depending on the model.

Configure your preferred sound effect for output sound.

― If Speaker Select is set to External , Sound Effect is disabled.

― Available only when Sound Mode is set to Standard .

• DTS TruSurround HD ( Off / On )

This function provides a virtual 5.1 channel surround sound experience through a pair of speakers using HRTF(Head

Related Transfer Function) technology.

• DTS TruDialog ( Off / On )

This function allows you to increase the intensity of a voice over background music or sound effects so that dialog can be heard more clearly.

• Equaliser

Use Equaliser to customize sound setting for each speaker.

Balance L/R : Adjusts the balance between the right and left speaker.

100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment): Adjusts the level of specific bandwidth frequencies.

Reset : Resets the equalizer to its default settings.

51

Speaker Settings

MENU m → Sound → Speaker Settings → ENTER E

Sound

Speaker Settings

The displayed image may differ depending on the model.

• Speaker Select ( External / Internal )

If you are listening to the sound track of a broadcast or movie through an external receiver, you may hear a sound echo caused by the difference in decoding speed between the products speakers and the speakers attached to your audio receiver. If this occurs, set the product to External .

― When you set Speaker Select to External , the products speakers are turned off.

You will hear sound through the external speakers only. When the Speaker Select is set to Internal , both the product speakers and the external speakers are on. You will hear sound through both.

― If there is no video signal, both the products speakers and the external speakers will be mute.

• Auto Volume ( Off / Normal / Night )

The volume can vary depending on the channel.

Automatically equalize the volume level when switching to another channel.

Normal equalizes the volume level on each channel, so that when you change channels, the volume level is the same.

Night equalizes and decrease the volume level on each channel, so each channel is quieter. Night is useful at night, when you may want to keep the volume low.

― To use the volume control of a connected source device, set Auto Volume to Off . A change to the volume control of the connected source device may not be applied if Auto Volume is set to Normal or Night .

52

Additional Settings

MENU m → Sound → Additional Settings → ENTER E

Sound

Additional Settings

The displayed image may differ depending on the model.

DTV Audio Level

(Digital channels only)

The TV cannot freely control the volume of the digital audio that it sends to the AV receiver. Use this to set the digital audio volume at a comfortable level.

― According to the type of broadcast signal, MPEG / HE-AAC can be adjusted between -10dB and 0dB.

― To increase or decrease the volume, adjust between the range 0 and -10 respectively.

Dolby Digital Comp

Some digital TV programmes provide 5.1-channel Dolby audio. This TV converts Dolby audio to stereo audio so that it can play the sound through the TV’s speakers. There are two methods to choose from. RF is for better sound at lower volumes, and Line is for higher volumes.

53

Reset Sound

MENU m → Sound → Reset Sound → ENTER E

Sound

Reset Sound

The displayed image may differ depending on the model.

Reset all sound settings to the factory defaults.

54

Chapter 06

Broadcasting

Configure the Broadcasting settings for the product.

Auto Tuning

MENU m → Broadcasting → Auto Tuning → ENTER E

Broadcasting

Auto Tuning

Aerial

Channel List

Schedule Manager

Edit Channel

Edit Favorites

Channel Settings

Air

The displayed image may differ depending on the model.

Available in TV mode only.

The Auto Tuning function memorizes all channels that are available over the air or through your cable system and adds them to the Channel List .

Auto Tuning

To start Auto Tuning , follow these steps:

1 Push MENU m → Broadcasting → Auto Tuning → Auto Tuning → ENTER E on your remote. The Auto Tuning screen appears.

2 On the Auto Tuning screen, select the source of your product signal.

― Air : If your product is connected to an antenna choose Air , and then press ENTER E. The product will automatically start memorizing channels.

― Cable : If your product is connected to a cable outlet, choose Cable , and then press ENTER E. Go to Step 3.

― Select Digital & Analogue , Digital or Analogue to scan for channels.

3

Sets Search Mode using / buttons. When done, select Scan , and then press ENTER E. The product will start memorizing channels.

― Channel memorization can take up to 45 minutes, depending on your cable system.

― Memorized channels are added to the Added Ch.

list. These are the channels you will see when you use the channel buttons on your remote.

55

Cancelling Auto Tuning

1 Press the Stop button.

2 A Stop Auto Tuning?

message appears.

3 Press the Yes button.

Cable Search Option

MENU m → Broadcasting → Auto Tuning → Cable Search Option →

ENTER E

Auto Tuning

Cable Search Option

(when the aerial was set to Cable )

Sets additional search options such as the frequency and symbol rate for a cable network search.

― Availability depends on the specific model and area.

The displayed image may differ depending on the model.

Available in TV mode only.

56

Aerial

MENU m → Broadcasting → Aerial → ENTER E

Broadcasting

Aerial Cable

The displayed image may differ depending on the model.

Available in TV mode only.

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the LED display.

• Air / Cable

57

Channel List

MENU m → Broadcasting → Channel List → ENTER E

Broadcasting

Channel List

The displayed image may differ depending on the model.

Available in TV mode only.

Register or delete channels. Add favourites channels or rename analogue channels.

Select a desired channel from Channel List to view the channel instantly.

― To navigate Channel List faster, press the channel buttons. The channel list changes page by page.

Icons found in the channel list page

A : Analogue channel

* : A channel that is selected

\ : Locked channels

Pressing the left cursor ( ) button on the remote control displays the Sorting page.

Pressing the right cursor ( ) button on the remote control displays the Mode page.

Sorting

Sort the list by Channel Number or by Name (Digital channels only).

Mode

Antenna

Select either Air or Cable as digital channel mode.

Edit Favorites

Edit favourites channel lists from Edit Channel .

Favourites 1 ~ Favourites 5

Shows all favourites channels, in up to five groups. Each group has a separate screen.

― The TV displays favourites groups only if you have added favouritess using Favourites 1 - to Favourites 5 .

58

All

Shows all channels.

Analog

Shows analogue channels.

Digital

Shows digital channels.

59

Schedule Manager

MENU m → Broadcasting → Schedule Manager → ENTER E

Broadcasting

Schedule Manager

The displayed image may differ depending on the model.

Available in TV mode only.

Watch a desired channel at a scheduled time.

• Aerial : DTV Cable / Cable

• Channel : Select the desired channel.

• Repeat : Once / Manual / Sat~Sun / Mon~Fri / Everyday

― Select Manual if you want to configure settings by day of the week.

• Date : Select the desired date.

• Start Time : Set the time to watch the desired channel.

60

Edit Channel

MENU m → Broadcasting → Edit Channel → ENTER E

Broadcasting

Edit Channel

The displayed image may differ depending on the model.

Available in TV mode only.

Manage channels saved on your TV. Delete channels, re-register deleted channels or rename analogue channels.

― Conveniently configure settings using the remote control buttons displayed at the bottom of the screen.

Icons found in the edit channel page

A : Analogue channel

* : A channel that is selected

\ : Locked channels

Deleting/registering channels

Deleting channels

Delete channels, if required. Note that deleting channels from the Recently Viewed or Most Viewed category does not remove the channels permanently. The channels are only removed from the categories.

1

Select channels to delete from the screen. To cancel, select again.

2

After selecting channels, select Delete from the screen to delete the channels.

Re-registering deleted channels

Register deleted channels again, if required. Deleted channels are grayed out and can only be found in the list of all channels.

The register function is enabled for deleted channels only.

1

Press TOOLS on the screen to display the Tools page. Select Category from the sub-menu items and then select All .

2

From the list of all channels, select deleted channels you want to register again.

3

After selecting channels, select Add from the screen to re-register the channels.

61

Editing registered channels

Pressing TOOLS from the Edit Channel page displays the following menu items. Provided functions may vary depending on the broadcast signal.

Option Name Operations

Aerial Select either Air or Cable as digital channel mode.

Category Channels saved on your TV are classified under the All , Added Ch.

, Recently

Viewed and Most Viewed categories. Select a desired category.

Edit Favorites

Rename Channel

Channel Info

Information

Set frequently viewed channels as favourites channels.

Change the names of analogue channels to suit your preferences. A channel name can be up to five characters long.

Check the information of the channel.

View information about the current broadcast programme on the air.

Locking/unlocking channels using a password

Lock specific channels to prevent children from accessing inappropriate content.

― To set a password, make sure Programme Rating Lock is set to On .

Locking channels

1

Select a channel from the Edit Channel page, and then select Programme Rating Lock from the screen. The password input window is displayed.

2

Enter the password. The selected channel is locked.

Unlocking channels

1

Select a locked channel from the Edit Channel page, and then select Programme Rating Lock Off from the screen. The password input window is displayed.

2

Enter the password. The selected channel is unlocked.

62

Edit Favorites

MENU m → Broadcasting → Edit Favorites → ENTER E

Broadcasting

Edit Favorites

The displayed image may differ depending on the model.

Available in TV mode only.

Creating a favourites channel list

Set frequently viewed channels as favourites channels. Favourites channels are indicated by a symbol in the Edit Channel or

Channel List page. A maximum of five favourites channel lists are allowed. Create different favourites channel lists for each family member.

― Conveniently configure settings using the remote control buttons displayed at the bottom of the screen.

Adding the current channel to a favourites channel list

Add the channel you are currently watching to a favourites channel list.

1 When watching TV, press TOOLS to display the Tools page. Select Edit Favorites from the sub-menu items.

2 From the displayed prompt box, select a favourites channel list to save the current channel to. Select OK .

3 The current channel is added in the selected favourites channel list. Select OK .

Adding multiple channels to a favourites channel list

Add multiple channels to a favourites channel list, if required.

1

Select Category from the screen to change the channel list in the centre of the screen to the channel list that contains the channels to add. Each time Category is selected, the category switches in the order Recently Viewed , Most Viewed , and Added Ch.

.

― Recently Viewed and Most Viewed are only enabled if they contain saved channels.

2

Select desired channels from the channel list in the centre of the screen.

3

Select Change Fav.

from the screen to change the favourites channel list on the right to another desired favourites channel list.

4

Select Add from the screen. The selected channels will create a favourites channel list.

63

Viewing channels saved under a favourites channel list

― Favourites channel lists are only displayed if they have been created previously.

When changing the channel using the channel buttons, channels saved in favourites channel lists can only be accessed.

1

Select Channel List from the Broadcasting menu. The channel list is displayed.

2

Pressing the right cursor ( ) button on the remote control displays the Mode page.

3

Select a favourites channel list among Favourites 1 – Favourites 5 .

4

Select channels from the selected favourites channel list.

― Selecting Channel List while watching a favourites channel will display the updated favourites channel list.

Editing favourites channel lists

Pressing TOOLS from one of the Favourites 1 - to Favourites 5 pages displays the following menu items.

Option Name Operations

Copy to Favorites Copy channels from a favourites channel list to another favourites channel list.

― This option is only available when channels under a favourites channel list are selected.

Rename Favorites Change the name of a favourites channel list.

― This option is only available when channels under a favourites channel list are selected.

Aerial Select either the Air or Cable signal.

Edit Channel

Information

Manage saved channels.

View information about the current broadcast programme on the air.

Deleting channels from a favourites channel list

Delete channels from a favourites channel list, if required.

1

Select Change Fav.

from the screen to change the favourites channel list on the right to another desired favourites channel list.

2

Select channels to delete from the selected favourites channel list.

3

Select Delete from the screen. The selected channels are deleted from the favourites channel list.

Changing the order of channels in a favourites channel list

Change the order of channels saved in a favourites channel list, if required.

1 Select Change Fav.

from the screen to change the favourites channel list on the right to another desired favourites channel list.

2 Select channels to rearrange from the selected favourites channel list.

3 Select Change order from the screen, and then change the order of the selected channels. To apply the new order of the channels, press the E button.

64

Renaming a favourites channel list

Change the name of a favourites channel list, if required.

1

Select Change Fav.

from the screen to change the favourites channel list on the right to another desired favourites channel list.

2

Press TOOLS on the screen. Sub-menu items are displayed.

3

Select Rename Favorites from the sub-menu items. A prompt box appears.

4

Change the favourites channel list using the prompt box. The name for a favourites channel list can be up to 20 characters long.

Copying channels between favourites channel lists

Copy channels from a favourites channel list to another favourites channel list, if required.

1 Select Change Fav.

from the screen to change the favourites channel list on the right to another desired favourites channel list.

2 Select channels to copy from the favourites channel list on the right.

3 Press TOOLS on the screen. Sub-menu items are displayed.

4 Select Copy to Favorites from the sub-menu items. A prompt box appears.

5 Select favourites channel lists to copy the channels to using the prompt box. The channels are saved to the selected favourites channel lists.

― To use Copy to Favorites , make sure channels are saved in a favourites channel list.

65

Channel Settings

MENU m → Broadcasting → Channel Settings → ENTER E

Channel Settings

Country (Area)

Manual Tuning

Fine Tune

Transfer Channel List

Delete CAM Operator Profile

The displayed image may differ depending on the model.

Available in TV mode only.

Country (Area)

Select your country so that the TV can correctly auto-tune the broadcasting channels. This depends on the country or region.

When the PIN input screen appears,enter your 4 digit PIN number.

• Digital Channel : Change the country for digital channels.

• Analogue Channel : Change the country for analogue channels.

Manual Tuning

Scans for a channel manually and stores in the TV .

If a channel is locked using the Channel Lock function, the PIN input window appears.

This function depends on the country and region.

When Aerial Source is set to Air or Cable

• Digital Channel Tuning : Scans for a digital channel.

1

Select the New .

― When selecting Aerial → Air : Channel , Frequency , Bandwidth

― When selecting Aerial → Cable : Frequency , Modulation , Symbol Rate

2

Select the Search . When scanning has finished, a channel is updated in the channel list.

• Analogue Channel Tuning : Scans for an analogue channel.

1

Select the New .

2

Set the Programme , Colour System , Sound System , Channel and Search .

― Channel

C (aerial channel mode) / S (cable channel mode): These two modes allow you to select a channel by entering the assigned number for each aerial broadcasting station or cable channel.

3

Select the Store . When scanning has finished, a channel is updated in the channel list.

66

Fine Tune

(analogue channels only)

If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, fine tune the channel manually. Scroll to the left or right until the image is clear.

― This function is only available in Cable mode.

― Settings are applied to the channel you’re currently watching.

― Fine tuned channels that have been saved are marked with an asterisk “*” on the right-hand side of the channel number in the channel banner.

― To reset the fine-tuning, select Reset .

Transfer Channel List

Imports or exports the channel map. When the PIN input screen appears, enter the PIN.

You should connect a USB storage device to use this function.

• Import from USB : Import channel list from USB.

• Export to USB : Export channel list to USB. This function is available when USB is connected.

Delete CAM Operator Profile

Select the CAM operator to delete.

― Availability depends on the specific model and area.

67

Subtitle

MENU m → Broadcasting → Subtitle → ENTER E

Subtitle

Subtitle

Primary Subtitle

Secondary Subtitle

Configures the subtitle options.

Subtitle

Show subtitles.

• Subtitle Mode : Set the subtitle mode.

• Subtitle Language : Set the subtitle language.

Primary Subtitle

Set the primary subtitle language.

Secondary Subtitle

Set the secondary subtitle language.

68

Audio Options

MENU m → Broadcasting → Audio Options → ENTER E

Audio Options

Audio Language

Audio Format

Audio Description

English

Stereo

Off

The displayed image may differ depending on the model.

Available in TV mode only.

Audio Language

(for digital broadcasts)

Change the default value for audio languages.

• Primary Audio : Set the primary audio language.

• Secondary Audio : Set the secondary audio language.

― The available language may differ depending on the broadcast.

Audio Format

(for digital broadcasts)

Change a desired audio format. The supported audio format may vary depending on the broadcast programme.

Audio Description

(Not available in all locations) (for digital broadcasts)

This function handles the Audio Stream for the AD ( Audio Description ) which is sent along with the Main audio from the broadcaster.

• Audio Description : Turn the audio description function on or off.

• Volume : Adjust the audio description volume.

69

Programme Rating Lock

MENU m → Broadcasting → Programme Rating Lock → ENTER E

Broadcasting

Programme Rating Lock

The Programme Rating Lock blocks programmes with ratings higher than those desired. This is useful for controlling what children watch on TV. This will not function for programmes originating from external sources, such as DVD players or USB files.

This PIN is required to watch a blocked programme.

― This option is available when the input source is TV .

― The default PIN number for a new product set is “0-0-0-0”.

― Availability depends on the specific model and area.

The displayed image may differ depending on the model.

Available in TV mode only.

70

Teletext Language

MENU m → Broadcasting → Teletext Language → ENTER E

Broadcasting

Teletext Language

The displayed image may differ depending on the model.

Available in TV mode only.

Teletext Language

Use this to set the teletext language.

― Availability depends on the specific model and area.

Primary Teletext

Set the primary teletext language.

Secondary Teletext

Set the secondary teletext language.

71

Common Interface

MENU m → Broadcasting → Common Interface → ENTER E

Broadcasting

Common Interface

The displayed image may differ depending on the model.

Available in TV mode only.

CI Menu

Enables the user to select from the CAM-provided menu. Select the CI Menu based on the menu PC Card.

CAM video transcoding

You can configure the setting to transcode the video codec from the CAM automatically. Turn it Off if you do not want to use it.

Application Info

View information about the CAM inserted into the CI slot and about the “CI or CI+ CARD” inserted into the CAM. You can install the CAM any time, with or without the TV turned on.

1

Purchase a CI CAM module at your nearest dealer or by phone.

2

Firmly insert the “CI or CI+ CARD” into the CAM in the direction of the arrow.

3

Insert the CAM with the “CI or CI+ CARD” into the common interface slot, in the direction of the arrow so that it aligns parallel with the slot.

4

Check if you can see a picture on a scrambled signal channel.

72

Channel Lock

MENU m → Broadcasting → Channel Lock → ENTER E

Broadcasting

Channel Lock On

The displayed image may differ depending on the model.

Available in TV mode only.

Prevent your children from accessing harmful content by locking channels.

• On / Off

― This option is available when the input source is TV .

― The default PIN number for a new product set is “0-0-0-0”.

― Availability depends on the specific model and area.

73

Chapter 07

Network

Network Status

MENU m → Network → Network Status → ENTER E

You can check the current network and Internet status.

Network Status

Your wireless network and Internet connection are setup and ready to use.

AP0000

MAC Address

IP Address

Subnet Mask

Gateway

DNS Server

** : ** : ** : ** : ** : **

***.

***.

***.

***.

***.

***.

***.

***.

***.

***.

***.

***.

***.

***.

***.

***.

Network connected, ready to use AllShare.

Disconnect IP Settings Retry Close

The displayed image may differ depending on the model.

Network Settings

MENU m → Network → Network Settings → ENTER E

Connect to a wireless network and use the product as a TV+signage using MagicInfo Express Content

Creator on your PC.

Network Settings

Your wireless network connection is setup and ready to use.

AP000

Ready to play your business content.

-Run the Content Creator on your PC, then create and schedule your content. You can send it to the Signage TV using the wireless network.

-Refer to the Content Creator manual for more information.

Refresh

The displayed image may differ depending on the model.

74

Network Setting (Wireless)

Connecting to a Wireless Network

Samsung recommends using IEEE 802.11n. When you play video over a network connection, the video may not play smoothly.

― Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer is currently being used by another device nearby, this will result in interference and communication failure.

― Your product supports only the following wireless network security protocols.

If you select the Pure High-throughput (Greenfield) 802.11n mode and the Encryption type is set to

WEP, TKIP or TKIP AES (WPS2Mixed) on your AP or wireless router, Samsung products will not support a connection in compliance with new Wi-Fi certification specifications.

― If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC

(Push Button Configuration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and WPA key in either mode.

― Connection Methods: You can setup the wireless network connection in three ways.

Auto Setup (Using the Auto Network Search function), Manual Setup, WPS(PBC)

Automatic Network Setup (Wireless)

Most wireless networks have an optional security system that requires devices that access the network to transmit an encrypted security code called an Access or Connection Information . The Connection

Information is based on a Pass Phrase, typically a word or a series of letters and numbers of a specified length you were asked to enter when you set up security for your wireless network. If you use this method of setting up the network connection, and have a Connection Information for your wireless network, you will have to enter the Pass Phrase during the the automatic or manual setup process.

How to set up automatically

1

Go to MENU m → Network → Network Settings .

2

The Network function searches for available wireless networks. When done, it displays a list of the available networks.

3

In the list of networks, press the ▲ or ▼ button to select a network, and then press the E button.

― If the desired wireless router does not appear, select Refresh to search again.

― If the router cannot be found after retrying, select the Stop button.

The Add Network button appears.

Select Add Network to add a wireless router to connect to.

4 If the Enter password.

screen appears, go to step 5. If you select a wireless router that does not have security, go to step 7.

5 If the router has security, enter the Enter password.

(Security key or PIN).

75

6

When done, use the down arrow button to move the cursor to Done , and then press E. The network connection screen appears and the verification process starts.

― A connection with the router is established, but the Internet cannot be accessed.

7 When the connection has been verified, the “ Your wireless network and Internet connection are setup and ready to use.

” message appears.

Manual Network Setup (Wireless)

Offices may use static IP addresses.

If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server address. Enter these values manually.

Getting the Network Connection Values

To view the Network connection values on most Windows computers, follow these steps.

1

Right click the Network icon on the bottom right of the screen.

2

In the pop-up menu that appears, click Status.

3

On the dialog that appears, click the Support tab.

4

On the Support Tab, click the Details button. The Network connection values are displayed.

How to set up manually

On the SMART Signage TV, go to MENU m → Network → Device Name and change the SMART

Signage TV's device name.

― If you use multiple SMART Signage TVs, make sure to change their device names.

1

Go to MENU m → Network → Network Settings .

2

The Network function searches for available wireless networks. When done, it displays a list of the available networks.

3

In the list of networks, press the u or d button to select a network, and then press the E button.

― If the desired wireless router does not appear, select Refresh to search again.

― If the router cannot be found after retrying, select the Stop button.

The Add Network button appears.

Select Add Network to add a wireless router to connect to.

4

If the Enter password.

screen appears, go to step 5. If you select a wireless router that does not have security, go to step 7.

5

If the router has security, enter the Enter password.

(Security key or PIN).

6

When done, use the down arrow button to move the cursor to Done , and then press E. The network connection screen appears and the verification process starts.

7

Select Stop while network connections are being attempted. This will stop the connection.

8

Select IP Settings on network connection screen. The IP Settings screen appears.

9

Select the field at the top, press E, and then set IP Settings to Enter manually . Repeat the entry process for each field in the IP Address .

― Setting IP Settings to Enter manually automatically changes DNS Setting to Enter manually .

76

10

When done, select OK at the bottom of the page, and then press E. The network test screen appears and the verification process starts.

11

When the connection has been verified, the “ Your wireless network and Internet connection are setup and ready to use.

” message appears.

WPS(PBC)

How to set up using WPS(PBC)

If your router has a WPS(PBC) button, follow these steps.

1

Go to MENU m → Network → Network Settings .

2

Select WPS(PBC) , press E, and then press E again.

3

Press the WPS(PBC) button on your router within 2 minutes. Your product automatically acquires all the network setting values it needs and connects to your network.

4

The network connection screen appears, and network setup is done.

77

Soft AP (Wi-Fi Hotspot)

MENU m → Network → Soft AP (Wi-Fi Hotspot) → ENTER E

Using this function, you can connect the product on your mobile devices if your mobile devices do not support Wi-Fi Direct .

Set the options for connection of Wi-Fi device.

• Soft AP (Wi-Fi Hotspot)

Turns on or off the Soft AP (Wi-Fi Hotspot) . When Soft AP (Wi-Fi Hotspot) is set to On , your mobile devices can find the product name in Wi-Fi connection list.

• Connection Information

Shows the security key.

• Connection Information Reset

Powering on the display creates a new security key and disconnect any existing Soft AP (Wi-Fi Hotspot) connection.

Off / On

78

To use this function, your mobile device should be supported by the Wi-Fi Direct .

Wi-Fi Direct

MENU m → Network → Wi-Fi Direct → ENTER E

Set to connect the product to wireless mobile devices. Using this function, you can connect wireless mobile devices with your product directly without a router.

To connect your mobile device with your product using Wi-Fi Direct, follow these steps:

1 Go to Wi-Fi Direct screen. The product starts to search devices.

2 Turn on the Wi-Fi Direct function on your device. Select the desired Wi-Fi device.

• PBC (Push Button Configuration): Press the WPS(PBC) button on your Wi-Fi device within 2 minutes. Your product automatically acquires all the network setting values it needs and connects to your network.

• PIN : Input the displayed PIN on your device.

― If you want to disconnect the device, select the connected Wi-Fi device, and then select Disconnected .

79

AllShare Settings

MENU m → Network → AllShare Settings → ENTER E

Shows a list of mobile phones or connected devices which have been set up to use the AllShare Play function with this product.

• Content Sharing

Using the AllShare Play Function

An alarm window appears informing you that media contents (videos, photos, music) sent from a mobile phone will be displayed on your product. The contents are played automatically 3 seconds after the alarm window appears. If you press the RETURN or EXIT button when the alarm window appears, the media contents are not played.

― The first time a device accesses your product through the media function, a warning popup window appears. Press the E button to select Allow . This permits the phone to access the product freely and use the AllShare Play function to play content.

― To turn off media contents transmissions from a mobile phone, set Deny in the AllShare Settings .

― Contents may not play on your product depending on their resolution and format.

― The E and ◄ / ► buttons may not work depending on the type of media content.

― Using the mobile device, you can control the AllShare Play . For details, refer to each mobile’s user’s guide.

Device Name

MENU m → Network → Device Name → ENTER E

Select or enter a device name.

This name can be shown on network remote controls over the network.

80

Chapter 08

Applications

Source List

MENU m → Applications → Source List → ENTER E

Source

TV AV HDMI1 HDMI2 PC USB

The displayed image may differ depending on the model.

Source allows you to select a variety of sources and change source device names.

You can display the screen of a source device connected to the product. Select a source from source list to display the screen of the selected source.

― The input source can also be changed by using the SOURCE button on the remote control.

― The screen may not display correctly if an incorrect source is selected for the source device you want to convert to.

― To view detailed information about connected source devices, press the TOOLS button from the Source page.

Edit Name

SOURCE → Source → TOOLS → Edit Name → ENTER E

Sometimes the screen will not display properly unless the name of a source device is specified in Edit Name .

In addition, it is best to rename the source device in Edit Name to obtain optimal picture quality.

― The list can include the following source devices. Source devices on the list differ depending on the selected source.

PC / Cable STB / Satellite STB / PVR STB / Game / Blu-ray / DVD / VCR / AV Receiver / Camcorder / DVI PC /

DVI Devices / TV / IPTV / HD DVD / DMA

― Available settings in the Picture menu depend on the current source and settings made in Edit Name .

Information

SOURCE → Source → TOOLS → Information → ENTER E

You can see detailed information about the selected external device.

81

MagicInfo

MENU m → Applications → MagicInfo → ENTER E

Applications

MagicInfo

The displayed image may differ depending on the model.

MagicInfo is a business solution that allows the product to be used as a signage (advertising media). Using the solution, play image and video files from the internal memory or a connected USB storage device. You can also play schedules created using the MagicInfo Express Content Creator on your computer.

Playing content from the internal memory or USB

Play content from the internal memory or a connected USB storage device.

Playing PC or mobile content

Send content via the MagicInfo Express Content Creator or a mobile app to the product for playback. If the internal memory is insufficient, connect a USB device and go to Options → Settings → Default Storage at the top right of the MagicInfo browser. Change the option to USB .

82

Schedule

Device : All Content : All Sort by : File Name Options

Press HOME or MagicInfo Player I on the remote control to access the application more quickly.

The displayed image may differ depending on the model.

Schedule

Play configured schedules.

Available features in the MagicInfo page

The MagicInfo list page provides the following features.

• Device

Select either Internal Memory or USB to search for a desired device list.

All / Internal Memory / USB

• Content

Select a content type as criterion to search for a desired content list.

All / My Templates / Video / Image

• Sort by

Specify the content sort criterion.

File Name / Recently played

• Options

Options menu items in the MagicInfo screen

Option Name

Play Seleted

Operations

Select and play desired content.

Send

Delete

Settings

Copy content to another storage device.

Delete desired content.

Configure detailed properties of content.

― See the following page for details on the Settings feature.

83

Settings

Settings

Select the storage location that you want to download scheduled channels from the network to.

Default Storage

Repeat Mode

Picture Size

Display Duration

Safely Remove USB Device

Reset Settings

Internal Memory

One

Close

The displayed image may differ depending on the model.

Default Storage

Select the storage location that you want to download scheduled channels from the network to.

• Internal Memory / USB

Repeat Mode

Set repeat mode whether to repeat playing contents or not.

• One / All

Picture Size

Set Picture Size to either Original Size or Full Screen .

• Original Size / Full Screen

― Available only for Video and Image content.

Display Duration

Set the duration for each page in a slideshow.

― Available only for Template and Image content.

Safely Remove USB Device

Safely removes USB memory

Reset Settings

Restore all the values under Settings to the default when the product was purchased.

84

Chapter 09

MagicInfo Express Content Creator

Refer to the MagicInfo Express Content Creator guide found in the user guide USB for details.

Installation requirements

HDD: At least 500 MB of free space

Operating system: Windows XP or later

Resolution: 1024x738 or higher

Using MagicInfo Express Content Creator

MagicInfo Express Content Creator is a program that allows you to conveniently create SMART Signage TV content using a variety of templates. Using MagicInfo

Express Content Creator, create and manage schedules to play content on SMART Signage TV at a specific time.

― To use MagicInfo Express Content Creator, download and install MagicInfo Express Content Creator from the MagicInfo Express Content Creator USB or http://www.samsung.com/displaysolutions/signagetv.

• Create Content : Create and manage templates that will be played on Samsung display devices.

• Schedule Content : Create and manage schedules to play content at specified times.

Managing templates

Using the templates provided in the program, organize a variety of content items based on predefined layouts to conveniently create new templates. Import and edit previously created templates.

Managing schedules

Configure and manage schedules to play content on Samsung display devices at specific times. Set the same schedule to play on specified days of the week or set different schedules to play by day of the week.

85

Chapter 10

Playing photos, videos and music (Media Play)

Enjoy videos, photos, music files saved on a USB Mass Storage Class (MSC) device.

Play photos, videos or music saved on a storage device.

Play a variety of content using the following methods.

• Using a USB device: Play media content such as videos, photos and music from a USB device.

• Connecting a storage device: Play media content saved on a storage device such as a smartphone, camera, PC or cloud service.

Read the following before using media play with a USB device

Caution

• Before connecting a USB device to the product, back up files to ensure your data is not damaged or lost.

Samsung Electronics is not liable for any damage or loss of data.

• Do not remove a USB device while it is loading.

• If a USB device is connected using a USB extension cable, the USB device may not be recognized or files saved on the device may not be able to be read.

• If the product does not recognize a connected USB device, the files on the USB device may be corrupted or may not be able to be played.

If this occurs, connect the USB device to the PC to format the device, then make sure the device is connected properly.

• USB HDD greater than 2TB is not supported.

86

Compatible devices with media play

• Some USB digital cameras, smartphones and audio devices may not be compatible with the product.

• Media play is only compatible with USB MSC devices.

• MSC device refers to a Mass Storage Class Bulk-Only Transport device.

Examples of MSC devices include Thumb drives, Flash card readers and USB HDDs. (USB hubs are not supported.)

These MSC devices must be connected directly to a USB port on the product.

• If more than one Picture Transfer Protocol (PTP) device is connected, only one will work at a time.

• If multiple MSC devices are connected, some devices may not be recognized. USB devices that require high power (higher than 500mA or 5V) may not be supported.

• If an overheating warning message appears when a USB device is connected or used, the USB device may not be recognized or function properly.

• The screensaver activates if the product is left idle for a period of time specified in Auto Protection Time .

• Power-saving mode on some external hard disk drives may automatically deactivate after connecting to the product.

File system and formats

• Media play may not function properly with unlicensed multimedia files.

• Media Transfer Protocol (MTP) is not supported.

• Supported file systems include FAT16, FAT32 and NTFS (read only).

• Media play supports the sequential JPEG format.

It does not support the progressive JPEG format.

• Images with a higher resolution take longer to be displayed on the screen.

• The maximum JPEG resolution supported is 15360x8640 pixels.

• If a file is incompatible or corrupted, a message Not Supported File Format.

appears.

• When sorting files in folder view mode, a maximum of 1000 files can be displayed in each folder.

• If a USB device contains 8000 files and folders or more, some files and folders may not open.

• DRM MP3 files downloaded from websites that charge a fee cannot be played.

― Digital Rights Management (DRM) refers to a system for protecting the copyrights of data circulated via the Internet or other digital media by enabling secure distribution and/or disabling illegal distribution of the data.

87

It is recommended to use a USB HDD that has a power adapter.

It is recommended to remove a USB device using the Disconnect USB Device function.

Using a USB device

Connecting a USB device

1

Turn on your product.

2

Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product.

3

The New device connected.

page automatically appears as soon as a USB device connects to the product.

― If only one USB device is connected, files saved on the USB device are displayed automatically.

― To view content saved on a USB device, connect the USB device to a USB port on the product.

Removing a USB device

Removing a USB device from Source

1

Press SOURCE on the remote control. Alternatively, go to Source using the OSD menu.

SOURCE → Source

2

Select USB from Source , and then press the TOOLS button on the remote control. Optional menu items are displayed.

3 Select Disconnect USB Device and wait until the USB device is disconnected. The USB device is disconnected.

88

Menu items in the media content list page

Option Name

Slide Show

Encoding

Play Selected

Operations

Start a slideshow.

― This menu item is not available if Sort by is set to Folder .

Select an encoding language if the title of media content appears corrupted.

Select and play desired content from the media content list.

Photos

c

Videos Music

c c c c

89

Pressing the INFO button while a file is selected will display information about the selected file.

Available buttons and features during photo playback

Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.

• Previous / Next

View the previous or next photo.

• Start Slide Show / Stop Slide Show

Start or stop a slideshow. Using a slideshow, it is possible to play all photos in a folder.

• Slideshow Settings

Speed : Change the slideshow speed.

Effects : Apply transition effects between photos.

• Zoom

Zoom in on photos up to 4x.

• Rotate

Rotate photos.

• Background Music

Play background music while viewing photos.

Background Music / Mini Player

― Make sure a music file is saved on the same device.

― Pause the current music playing or switch to another music file using Mini Player .

• Settings

Option Name

Picture Mode

Sound Mode

Information

Operations

Change the Picture Mode .

Change the Sound Mode .

― This menu item is only available when Background Music is playing.

View information about a file.

90

Available buttons and features during video playback

Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.

• Pause / Play

Pause or play a video.

The following features are available in pause mode. Note that sound cannot be heard in pause mode.

• Rewind / Fast Forward

Rewind or fast forward a video. Speed up playback up to 3x, if required. To change the playback speed to the original speed, select ∂.

• Previous / Next

To play the previous video, select  twice. Selecting  once will play the current video from the beginning.

To play the next video, select ‚.

• Search

Select and play another video in the same folder. ( Search Titles )

• Repeat Mode

Configure Repeat Mode .

( Off , Repeat One , Repeat All )

• Picture Size

Change the screen size ( Picture Size ). Supported screen sizes vary depending on the image. ( Original / Mode1 / Mode2 / Smart View 1 /

Smart View 2 )

• Settings

Option Name Operations

Picture Mode Change the Picture Mode .

Sound Mode

Audio Language

Information

Change the Sound Mode .

Play a video using a desired language. This feature only activates when a streaming file that supports multiple audio formats is playing.

View information about a file.

91

Available buttons and features during music playback

Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.

• Pause / Play

Pause or play music.

• Rewind / Fast Forward

Rewind or fast forward music. Speed up playback up to 3x, if required. To play the previous music file, select ∂ twice.

• Previous / Next

To play the previous music file, select  twice. Selecting  once will play the current music from the beginning.

To play the next music file, select ‚.

• Repeat

Configure Repeat mode. One Song plays the current music file repeatedly. All plays all files in a folder repeatedly.

• Shuffle

Enable or disable shuffle playback mode.

• Sound Mode

Change the Sound Mode .

92

Supported Subtitle and Media play file formats

Subtitle

External

• MPEG-4 timed text (.ttxt)

• SAMI (.smi)

• SubRip (.srt)

• SubViewer (.sub)

• Micro DVD (.sub or .txt)

• SubStation Alpha (.ssa)

• Advanced SubStation Alpha (.ass)

• Powerdivx (.psb)

Internal

• Xsub

Container: AVI

• SubStation Alpha

Container: MKV

• Advanced SubStation Alpha

Container: MKV

• SubRip

Container: MKV

• MPEG-4 timed text

Container: MP4

Supported image resolutions

Type

JPEG

MPO

BMP

93

Supported music file formats

File Extension

*.aac, *.flac, *.m4a, *.mid, *.midi,

*.mp3, *.mpa, *.ogg, *.wav, *.wma

Supported Video Formats

• Video content will not play, or not play correctly, if there is an error in the content or the container.

• Sound or video may not work if the contents have a standard bitrate/frame rate above the compatible Frame/sec listed in the table above.

• If the Index Table is in error, the Seek (Jump) function is not supported.

• You may experience file stuttering while playing a video through a network connection.

• The menu may take longer to appear if the video’s bit rate exceeds 10Mbps.

• Some USB/digital camera devices may not be compatible with the player.

Video Decoder

Supports up to H.264, Level 4.1

H.264 FMO / ASO / RS, VC1 SP / MP / AP L4 and AVCHD are not supported.

For all Video codecs except MVC, VP8, VP6:

• Below 1280 x 720: 60 frame max

• Above 1280 x 720: 30 frame max

GMC 2 over is not supported.

Supports only BD MVC Spec.

Audio Decoder

Supports up to WMA 10 Pro 5.1 channel.

WMA lossless audio is not supported.

QCELP, AMR NB/WB are not supported.

If Vorbis is only in Webm container, supports up to 2 channel.

94

Container

ps ts vob vro

3gpp asf avi flv mkv mov mp4

Video Codec

DivX 3.11 /DivX4.X

XVID

H.264 BP/MP/HP

MPEG-4 SP/ASP

WINDOW MEDIA VIDEO V9

MPEG2

MPEG1

H.263

DivX5.x

DivX6.X

Resolution

1280 x 720

Frame rate

(fps)

60

Bit rate

(Mbps)

30

Audio Codec

AAC

AC3

ADPCM

DD+

DTS Core

HE-AAC

LPCM

MP3

WMA

95

Container

ps ts vob vro

3gpp asf avi flv mkv mov mp4

Video Codec

DivX 3.11 /DivX4.X

XVID

H.264 BP/MP/HP

MPEG-4 SP/ASP

WINDOW MEDIA VIDEO V9

MPEG2

MPEG1

H.263

DivX5.x

DivX6.X

MOTION JPEG

Resolution

1920 x 1080

640 x 480

Frame rate

(fps)

30

30

Bit rate

(Mbps)

30

8

Audio Codec

AAC

AC3

ADPCM

DD+

DTS Core

HE-AAC

LPCM

MP3

WMA

96

Chapter 11

System

Setup

MENU m → System → Setup → ENTER E

System

Setup

Menu Language

Time

Eco Solution

Auto Protection Time

Screen Burn Protection

Ticker

English

Off

Off

The displayed image may differ depending on the model.

Initial settings (Setup)

After powering on the product for the first time, configure basic settings such as the language, channel and time.

Press the button. Setup is available only when Source is set to TV .

1 Selecting a language

Press the or button, and then press the E button. Specify the OSD menu language.

2 Regional Settings

Select your region to optimise the system.

3 Channel Source

TV input source setup.

Set Channel Source to Set-top box to display the Source options.

Aerial / Set-top box / No TV(Signage Only)

4

Auto Tuning

This feature automatically searches and configures broadcast signals connected to the product.

To configure settings later, press the Stop button.

― Auto Tuning does not appear if Set-top box or No TV(Signage Only) is selected.

97

5

Network Settings

Select a wireless router from the list of retrieved routers and press the E button.

If a wireless router to connect to is not found, select the arrow on the right and press the Skip button.

6 Auto Power Off

Set Auto Power Off option. If you select On , the display will be turned off after no user interaction is detected for 4 hours.

7 Setup Complete!

To watch TV using the product now, select OK .

98

Menu Language

MENU m → System → Menu Language → ENTER E

System

Menu Language English

The displayed image may differ depending on the model.

Set the menu language.

― A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions on your PC.

99

Time

MENU m → System → Time → ENTER E

Time

Clock

Sleep Timer

On Timer

Off Timer

Holiday Management

Off

The displayed image may differ depending on the model.

You can configure Clock . You can also set the product to automatically turn on or off at a specified time using the Timer function.

Clock

Clock Mode

Set the current time manually or automatically.

Auto : Have the product set the current time automatically using the time from a digital channel.

― You must have the cable or an antenna connected to the product to set the time automatically.

Manual : Set the current time manually.

Clock Set

Set the clock to use the various various timer features of the product.

Set the Date and Time .

Select Clock Set . Select Date or Time , and then press E.

Use the number buttons to enter numbers or press the up and down arrow buttons. Use the left and right arrow buttons to move from one entry field to the next. Press E when done.

― Available only when Clock Mode is set to Manual .

― You can set the Date and Time directly by pressing the number buttons on the remote control.

100

Time Zone

Select your time zone.

― This function is only available when the Clock Mode is set to Auto .

Time Offset

Select the correct time offset your timezone.

― This function is only available when the Clock Mode is set to Auto .

Sleep Timer

Automatically shuts off the product after a preset period of time.

( Off / 30 min / 60 min / 90 min / 120 min / 150 min / 180 min )

― Use the up and down arrows to select a period of time, and then press E. To cancel Sleep Timer , select Off .

On Timer

Set On Timer so that your product turns on automatically at a time and on a day of your choosing.

The power is turned on with the specified volume or input source.

On Timer : Set the on timer by making a selection from one of the seven options. Ensure you set the current time first.

( On Timer1 ~ On Timer7 )

― You must set the clock before you can use On Timer .

• Setup : Select Off , Once , Everyday , Mon~Fri , Mon~Sat , Sat~Sun or Manual . If you select Manual , you can choose the days you want On Timer to turn on your product.

― The check mark indicates days you’ve selected.

• Time : Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers.

Use the left and right arrow buttons to change entry fields.

• Volume : Set the desired volume level. Use the left and right arrow buttons to change the volume level.

• Source : Select the input source of your choice.

• Aerial (when the Source is set to TV ): Select Air or Cable .

• Channel (when the Source is set to TV ): Select the desired channel.

• Music / Photo (when the Source is set to USB ): Select a folder in the USB device containing music or photo files you want played when the product turns on automatically.

101

― This function is available only when a USB device is connected.

― If there is no music file on the USB device or you don’t select a folder containing a music file, the Timer function does not operate correctly.

― If there is only one photo file in the USB, the Slide Show will not play.

― If a folder name is too long, the folder cannot be selected.

― Each USB you use is assigned its own folder. When using more than one of the same type of USB, make sure the folders assigned to each USB have different names.

― We recommend that you use a USB memory stick and a multi card reader when using On Timer . The On Timer function may not work with USB devices with a built-in battery, MP3 players, or PMPs made by some manufacturers because the product can take too long to recognize these devices.

102

Off Timer

Set the off timer ( Off Timer ) by making a selection from one of the seven options. ( Off Timer1 ~ Off Timer7 )

― You must set the clock before you can use Off Timer .

• Setup : Select Off , Once , Everyday , Mon~Fri , Mon~Sat , Sat~Sun or Manual . If you select Manual , you can choose the days you want Off Timer to turn off your product.

― The check mark indicates days you’ve selected.

• Time : Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use the left and right arrow buttons to change entry fields.

Holiday Management

Timer will be disabled during a period specified as a holiday.

• Add : Specify the period you want to add as a holiday.

Select the start and end dates of the holiday you want to add using the / buttons, and click the Save button.

The period will be added to the list of holidays.

Start : Set the start date of the holiday.

End : Set the end date of the holiday.

Delete : Delete all items from the list of holidays.

Select Delete . The message " Delete all holidays?

" will appear.

Select Yes . All holidays will be deleted.

• Apply : Set the On Timer and Off Timer to not activate on public holidays.

Press E to select the On Timer and Off Timer settings you do not want to activate.

The selected On Timer and Off Timer will not activate.

103

Eco Solution

MENU m → System → Eco Solution → ENTER E

Eco Solution

Energy Saving

Eco Sensor

No Signal Power Off

Auto Power Off

Off

Off

15 min

On

The displayed image may differ depending on the model.

Energy Saving

Reduce the power consumption by adjusting the screen brightness.

Selecting Picture Off switches off the screen. The volume is not disabled.

To switch the screen on, press any button other than the volume button.

• Off / Low / Medium / High

Eco Sensor

Eco Sensor

To enhance your power savings, the picture settings will automatically adapt to the light in the room.

• Off / On

― Adjusting the Backlight setting under Picture while Eco Sensor is on will disable the Off .

Min. Backlight

When Eco Sensor is On , you can manually adjust the minimum screen brightness. Min. Backlight is the darkest backlight mode. Make sure the Min. Backlight setting is lower than the Backlight setting.

― If Eco Sensor is On , the display brightness may change (become slightly darker or brighter) depending on the surrounding light intensity.

104

Eco Solution

Energy Saving

Eco Sensor

No Signal Power Off

Auto Power Off

The displayed image may differ depending on the model.

Off

Off

15 min

On

No Signal Power Off

Save power by turning the device off when no signal is received from any source.

• Off / 15 min / 30 min / 60 min

― Disabled when an attached PC is in power saving mode.

― This product is set to 15 min by default.

― The product will automatically power off at a specified time. The time can be changed as required.

Auto Power Off

The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel within 4 hours to prevent overheating.

• Off / On

― The off timer can be set within a range of 1 to 23 hours. The product will automatically power off after the specified number of hours.

― This option is only available when Auto Power Off is set to On .

― For products for the market in some regions, the Auto Power Off is set to automatically activate 4 hours after the product powers on. This is done in accordance with power supply regulations. If you do not want the timer to activate, go to

MENU m → System → Eco Solution and set Auto Power Off to Off .

105

Auto Protection Time

MENU m → System → Auto Protection Time → ENTER E

System

Auto Protection Time Off

The displayed image may differ depending on the model.

If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the formation of burnt in ghost images on the screen.

― Displaying a still image for longer than four hours can cause image retention.

• Off / 2 hours / 4 hours / 8 hours / 10 hours

106

Screen Burn Protection

MENU m → System → Screen Burn Protection → ENTER E

Screen Burn Protection

Pixel Shift

Timer

Immediate display

Side Grey

Off

Off

Off

Off

The displayed image may differ depending on the model.

To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology.

Pixel Shift moves the picture slightly on the screen.

The Pixel Shift Time setting allows you to programme the time between movements of the picture in minutes.

Pixel Shift

Minimize image retention by finely moving pixels horizontally or vertically.

• Pixel Shift ( Off / On )

Horizontal : Sets how many pixels the screen moves horizontally.

Vertical : Sets how many pixels the screen moves vertically.

Time : Set the time interval for performing the horizontal or vertical movement, respectively.

― Horizontal , Vertical and Time are enabled only when Pixel Shift is set to On .

Available Pixel Shift Settings and Optimum Settings.

Available Settings Optimum Settings

Horizontal (pixels) 0 ~ 4 4

Vertical (pixels) 0 ~ 4 4

Time (minute) 1 min ~ 4 min 4 min

― The Pixel Shift value may differ depending on the product size (inches) and mode.

― Displaying a still image or a 4:3 output for an extended period of time may cause image retention. This is not a defect in the product.

― This function is not available in the Screen Fit mode.

107

Screen Burn Protection

Pixel Shift

Timer

Immediate display

Side Grey

The displayed image may differ depending on the model.

Off

Off

Off

Off

Timer

You can set the timer for Screen Burn Protection .

The Timer feature stops automatically after a specified period of time.

Timer

• Off

• Repeat : Display the image retention-preventive pattern set in Mode at specified time intervals(Period).

• Interval : Display the image retention-preventive pattern set in Mode for a specified period of time (from Start Time to

End Time ).

― The option is enabled only when Clock Set is configured.

― Mode , Period , Time , Start Time and End Time are enabled only when Timer is set to Repeat or Interval .

Mode

Select a screen protective pattern to display.

• Pixel : Pixels on the screen alternate black continuously.

• Rolling bar : A vertical bar moves left to right.

• Fading screen : The entire screen becomes brighter, then darker.

― The Rolling bar and Fading screen patterns appear only once regardless of the specified repeat period or time.

Period

Specify the time interval to activate the Screen Burn Protection function.

― The option is enabled when Repeat is selected for Timer .

Time

Specify the duration to keep the Screen Burn Protection function on.

― The option is enabled when Pixel is selected for Mode .

108

Start Time

Set the start time to activate the screen protection function.

― The option is enabled when Interval is selected for Timer .

End Time

Set the end time to deactivate the screen protection function.

― The option is enabled when Interval is selected for Timer .

109

Screen Burn Protection

Pixel Shift

Timer

Immediate display

Side Grey

The displayed image may differ depending on the model.

Off

Off

Off

Off

Immediate display

Select the screen saver you want to display immediately.

• Off / Pixel / Rolling bar / Fading screen

Side Grey

When the screen is set to 4:3 aspect ratio, adjust the brightness of white margins on sides to protect the screen.

• Off / Right / Dark

110

Ticker

MENU m → System → Ticker → ENTER E

Ticker

Ticker

· Message

·

Time

· Position

· Motion

· Font Style

Off

Off

The displayed image may differ depending on the model.

The Ticker function is only available when Menu Language is set to English .

Ticker

Input text while a video or image is displayed and display the text on the screen.

• Off / On

― Message , Time , Position , Motion , and Font options are enabled only when Ticker is set to On .

Message

Enter a message to display on the screen.

Time

Set the Start Time and End Time to display a Message .

• Start Time

• End Time

Position

Select an orientation to display a Message from Horizontal and Vertical .

• Horizontal ( Left / Centre / Right )

• Vertical ( Up / Middle / Down )

Motion

Specify the Direction and Speed to display a Message .

• Motion ( Off / On )

• Direction ( Left / Right / Up / Down )

• Speed ( Slow / Normal / Fast )

― Direction and Speed are enabled only when Motion is set to On .

Font Style

Configure the message font options.

111

Source AutoSwitch Settings

MENU m → System → Source AutoSwitch Settings → ENTER E

Source AutoSwitch Settings

Source AutoSwitch

· Primary Source Recovery

·

Primary Source

· Secondary Source

Off

Off

All

HDMI1

The displayed image may differ depending on the model.

Turning on the display with Source AutoSwitch On , and the previous video source selection is not active, the display will automatically search the different video input sources for active video.

Source AutoSwitch

When the Source AutoSwitch is On , the display video source will automatically be searched for active video.

The Primary Source selection will be activated, if the current video source is not recognized.

Secondary Source selection will become active, if no primary video source is available.

If both the primary and secondary input sources are not recognized, the display will perform two searches for an active source, each search checking the primary and then secondary source. If both searches fail, the display will return to the first video source and display a message indicating that there is no signal.

When the Primary Source selection is set to All , the display will search all the video source inputs twice in sequence looking for an active video source, returning back to the first video source in the sequence if no video is found.

Primary Source Recovery

Select whether to restore the selected primary input source when a primary input source is connected.

― The Primary Source Recovery function is disabled if Primary Source is set to All .

Primary Source

Specify Primary Source for the automatic input source.

Secondary Source

Specify Secondary Source for the automatic input source.

112

General

MENU m → System → General → ENTER E

General

Game Mode

Auto Power

Safety Lock

Button Lock

USB Auto Play Lock

Standby Control

Lamp Schedule

Off

Off

Auto

Off

Off

Off

Off

The displayed image may differ depending on the model.

Game Mode

When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by selecting game mode.

• Off / On

― Precautions and limitations for Game Mode

To disconnect the game console and connect another external device, set Game Mode to Off in the setup menu.

― Game Mode is not available when the input source is set to TV . After connecting the game console, set Game Mode to

On . Unfortunately, you may notice reduced picture quality.

― If Game Mode is On

Picture Mode is set to Standard and Sound Mode is set to Movie .

Auto Power

Enabling this option will automatically power on the product if the power cable is connected.

• Off / On

Safety Lock

It sets safe lock function.

• Off / On

All the menus and buttons of the product and remote control, except for the LOCK button on the remote control, will be locked by the Safety Lock function.

To unlock the menus and buttons, press the LOCK button and then enter the password (default password: 0 - 0 - 0 - 0).

113

General

Button Lock

USB Auto Play Lock

Standby Control

Lamp Schedule

OSD Display

The displayed image may differ depending on the model.

Off

Off

Auto

Off

Button Lock

It sets safe lock function.

• Off / On

This menu can be used to lock the buttons on the product.

Only the remote control can control the product if Button Lock is set to On .

USB Auto Play Lock

Lock USB memory devices to prevent them from being auto detected.

• Off / On

Standby Control

You can set the screen standby mode to be applied when an input signal is received.

• Auto

Power-saving mode will activate if no input signals are detected even though a source device is connected to the display.

The message No Signal will appear if no source device is connected.

• On

Power-saving mode will activate if no input signals are detected.

• Off

The message No Signal will appear if no input signals are detected.

― The Standby Control option is only enabled when Source is set to HDMI1 , HDMI2 .

― If No Signal is displayed although a source device is connected, check the cable connection.

114

General

Button Lock

USB Auto Play Lock

Standby Control

Lamp Schedule

OSD Display

The displayed image may differ depending on the model.

Off

Off

Auto

Off

Lamp Schedule

Enables the lamp value to be adjusted to a user-specified value at a specified time in MDC mode.

• Off / On

OSD Display

Displays or hides a menu item on the screen.

• Source OSD : Off / On

• No Signal OSD : Off / On

115

Change PIN

MENU m → System → Change PIN → ENTER E

System

Change PIN

The displayed image may differ depending on the model.

The Change PIN screen will appear.

Choose any 4 digits for your PIN and enter it in Enter New PIN . Reenter the same 4 digits in Confirm New PIN .

When the Confirm screen disappears, press the Close button. The product has memorized your new PIN.

― Default password: 0 - 0 - 0 - 0

116

Clone Product

MENU m → System → Clone Product → ENTER E

Clone Product

Clone to USB

Clone From USB

The displayed image may differ depending on the model.

Reset System

MENU m → System → Reset System → ENTER E

System

Reset System

The displayed image may differ depending on the model.

Export the product settings to a USB device or load the settings via a USB device.

This option is useful when assigning the same settings to several products.

• Clone to USB : Copy the product settings to a USB device.

• Clone From USB : Assign the settings saved in a USB device to the product.

After configuration is complete, the product is rebooted automatically.

― The option may not work properly if the USB device contains a file other than a settings file.

― Confirm that the USB device functions properly before running the option.

― The option is available for products with the same Model Code and Software Version .

Go to Support → Contact Samsung and find the product Model Code and Software Version .

This option returns the current settings under system to the default factory settings.

117

Reset All

MENU m → System → Reset All → ENTER E

System

Reset All

The displayed image may differ depending on the model.

DivX ® Video On Demand

MENU m → System → DivX ® Video On DemandENTER E

System

DivX ® Video On Demand

The displayed image may differ depending on the model.

This option returns all the current settings for a display to the default factory settings.

Shows the registration code authorized for the product.

If you connect to the DivXⓇ web site and register using that code, you can download the VOD registration file.

For more information about DivXⓇ VOD, visit “http://vod.divx.com”.

118

Chapter 12

Support

Current Version : This is the software version already installed in the product.

Software Update

MENU m → Support → Software Update → ENTER E

The Software Update menu lets you upgrade your product software to the latest version.

― Be careful not to turn off the power until the upgrade is complete. The product will turn off and on automatically after completing the software upgrade.

― When you upgrade software, all video and audio settings you have made will return to their default settings. We advise you to write down your settings so that you can easily reset them after the upgrade.

Update now

Update the software to the latest version.

― Performing a software update via USB will display the corresponding update window after a maximum of two minutes.

Use Mode

MENU m → Support → Use Mode → ENTER E

Select the appropriate mode according to where the product is used.

If you choose Demo Mode , the demo content will be played automatically and the picture settings will be reset in 5 minutes after change.

• Standard Use / Demo Mode

119

Contact Samsung

MENU m → Support → Contact Samsung → ENTER E

View this information when your product does not work properly or when you want to upgrade the software.

You can find information regarding our call centres and how to download products and software.

― Contact Samsung and find the product Model Code and Software Version .

120

Chapter 13

Troubleshooting Guide

Before calling Samsung Customer Service

Centre, test your product as follows. If the problem persists, contact Samsung

Customer Service Centre.

If the screen remains blank, check the PC system, video controller and cable.

Requirements Before Contacting Samsung Customer Service Centre

Testing the Product

Check if your product is operating normally by using the product test function.

If the screen remains blank while the power LED blinks even when the product is correctly connected to a PC, perform product testing.

1

Power off both the PC and product.

2

Disconnect all the cables from the product.

3 Power on the product.

4 If No Signal is displayed, the product is operating normally.

Checking the Resolution and Frequency

Not Optimum Mode will briefly be displayed if a mode that exceeds a supported resolution is selected (refer to Supported Resolutions).

121

Check the followings.

Installation issue (PC mode)

The screen keeps switching on and off.

Check the cable connection between the product and PC, and ensure the connection is secure.

Blank spaces are found on all four sides of the screen when an HDMI or HDMI-DVI cable is connected to the product and

PC.

The blank spaces found on the screen have nothing to do with the product.

Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the screen size in the HDMI or DVI settings for the graphics card.

If the graphics card settings menu does not have an option to adjust the screen size, update the graphics card driver to the latest version.

(Please contact the graphics card or computer manufacturer for further details about how to adjust the screen settings.)

Screen issue

The power LED is off. The screen will not switch on.

No Cable Connected is displayed on the screen (refer to

"Connecting to a PC").

Not Optimum Mode is displayed.

The images on the screen look distorted.

Make sure that the power cord is connected.

Check that the product is connected correctly with a cable

Check that the device connected to the product is powered on.

This message is displayed when a signal from the graphics card exceeds the product's maximum resolution and frequency.

Refer to the Standard Signal Mode Table and set the maximum resolution and frequency according to the product specifications.

Check the cable connection to the product

122

Screen issue

The screen is not clear. The screen is blurry.

The screen appears unstable and shaky.

There are shadows or ghost images left on the screen.

The screen is too bright. The screen is too dark.

Screen colour is inconsistent.

White does not really look white.

There is no image on the screen and the power LED blinks every 0.5 to 1 second.

The product will turn off automatically.

Picture quality of the product is different from the dealer shop where it was purchased.

Adjust Coarse and Fine .

Remove any accessories (video extension cable, etc) and try again.

Set the resolution and frequency to the recommended level.

Check that the resolution and frequency of the PC and graphics card are set within a range compatible with the product. Then, change the screen settings if required by referring to the Additional

Information on the product menu and the Standard Signal Mode Table.

Adjust Brightness and Contrast .

Go to Picture and adjust the Colour Space settings.

Go to Picture and adjust the White Balance settings.

The product is in power-saving mode.

Press any key on the keyboard or move the mouse to return to the previous screen.

Go to System and make sure Sleep Timer is set to Off .

If a PC is connected to the product, check the power status of the PC.

Make sure the power cable is connected properly to the product and power outlet.

If the signal from a connected device is not detected, the product automatically turns off after 10 to 15 minutes.

Use an HDMI cable to obtain high-definition (HD) picture quality.

123

Screen issue

The screen display does not look normal.

The brightness and colour do not look normal.

Broken lines are displayed on the edges of the screen.

Lines (red, green or blue) are displayed on the screen.

The display looks unstable and then freezes.

The screen cannot be displayed in full screen.

Encoded video content may cause the display to appear corrupted in scenes featuring fast moving objects such as in a sports event or action video.

Low signal level or low picture quality may cause the display to appear corrupted. This does not mean the product is defective.

A cell phone within a distance of one-meter radius may cause static on analogue and digital products.

Go to Picture and adjust the screen settings such as Picture Mode , Colour , Brightness and

Sharpness .

Go to System and adjust the Eco Solution settings.

Reset the screen settings to the default settings.

If Picture Size is set to Screen Fit , change the setting to 16:9 .

These lines are displayed when there is a defect in DATA SOURCE DRIVER IC on the SMART Signage TV.

Contact a Samsung Service Centre to resolve the issue.

The screen may freeze when a resolution other than the recommended resolution is used or if the signal is not stable. To resolve the issue, change the PC resolution to the recommended resolution.

A scaled SD (4:3) content file can cause black bars on both sides of an HD channel screen.

A video with an aspect ratio different from the product can cause black bars at the top and bottom of the screen.

Change the screen size setting to full screen on the product or source device.

Sound issue

There is no sound.

Check the connection of the audio cable or adjust the volume.

Check the volume.

124

Sound issue

The volume is too low.

Video is available but there is no sound.

There is static coming from the speakers.

There is audible sound when the volume is muted.

Sound from the SMART Signage TV does not change after

Sound Mode is changed.

Adjust the volume.

If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software programme.

If an HDMI cable is connected, check the audio output settings on the PC.

Go to Sound and change Speaker Select to Internal .

If a source device is used

• Make sure the audio cable is properly connected to the audio input port on the product.

• Check the audio output settings for the source device.

(For example, if an HDMI cable is connected to the SMART Signage TV, the audio setting for the cable box may need to be changed to HDMI.)

If the product has a headphone port, make sure nothing is connected to it.

Reconnect the power cable to the device and then reboot the device.

Check the cable connection. Make sure a video cable is not connected to an audio input port.

Check the signal strength after connecting a cable.

Low signal level can cause corrupted sound.

When Speaker Select is set to External , the volume button and mute function are disabled.

Adjust the volume for the external speakers.

Audio settings for main speakers are separate from the internal speakers on the product.

Changing or muting the volume on the product does not affect an external amplifier(decoder).

Audio settings for main speakers are separate from the internal speakers on the product.

Audio settings on a source device do not affect the internal speaker settings on the product.

125

Sound issue

There is an echo sound coming from the speakers.

Remote control issue

The remote control does not work.

Different decoding speeds between the product speakers and external speakers can cause an echo.

In this case, set Speaker Select to External .

Make sure that the batteries are correctly in place (+/-).

Check if the batteries are flat.

Check for power failure.

Make sure that the power cord is connected.

Check for any special lighting or neon signs switched on in the vicinity.

Source device issue

A beeping sound is heard when my PC is booting.

Other issue

The product smells like plastic.

The product appears tilted.

Audio or video cuts out intermittently.

If a beeping sound is heard when your PC is booting, have your PC serviced.

The plastic smell is normal and disappears over time.

Remove and then attach the stand again to the product.

Check the cable connection and connect it again if required.

Using a very hard or thick cable may corrupt audio and video files.

Make sure cables are flexible enough to ensure durability. When mounting the product onto a wall, it is recommended to use right-angle cables.

126

Other issue

Small particles are found on the edges of the product.

The PIP menu is not available.

When I try to change the PC resolution, a message The defined resolution is not supported.

appears.

There is no sound from the speakers in HDMI mode when a

DVI-HDMI cable is connected.

HDMI Black Level is not functioning properly on an HDMI device with YCbCr output.

There is no sound in HDMI mode.

The particles are part of the product design. The product is not defective.

The menu is enabled or disabled depending on the Source mode.

The message The defined resolution is not supported.

appears if the input source resolution exceeds the maximum resolution of the display.

To resolve the issue, change the PC resolution to a resolution supported on the display.

DVI cables do not transmit sound data.

Make sure to connect the audio cable to the correct input jack to enable audio.

This function is available only when a source device, such as a DVD player and STB, is connected to the product via an HDMI (RGB signal) cable.

Displayed picture colours may not look normal. Video or sound may not be available. This can occur if a source device that only supports an older version of the HDMI standard is connected to the product.

If these issues occur, connect an audio cable along with the HDMI cable.

Some PC graphics cards may not automatically recognize HDMI signals that do not include sound. In this case, manually select a sound input.

PC

Sound input

Auto

Screen mode

PC settings

127

Refer to the user manual for your PC or graphics card for further instructions on adjustment.

Q & A

Question

How can I change the frequency?

How can I change the resolution?

Answer

Set the frequency on your graphics card.

• Windows XP: Go to Control Panel Appearance and Themes Display Settings

Advanced → Monitor and adjust the frequency in Monitor Settings.

• Windows ME/2000: Go to Control Panel Display Settings Advanced Monitor and adjust the frequency in Monitor Settings.

• Windows Vista: Go to Control Panel Appearance and Personalization Personalize

Display Settings → Advanced Settings Monitor and adjust the frequency in Monitor

Settings.

• Windows 7: Go to Control Panel Appearance and Personalization Display Adjust resolution → Advanced Settings Monitor and adjust the frequency in Monitor Settings.

• Windows 8: Go to Settings Control Panel Appearance and Personalization Display

Adjust resolution Advanced Settings Monitor and adjust the frequency in Monitor

Settings.

• Windows XP: Go to Control Panel Appearance and Themes Display Settings and adjust the resolution.

• Windows ME/2000: Go to Control Panel Display Settings and adjust the resolution.

• Windows Vista: Go to Control Panel Appearance and Personalization Personalize

Display Settings and adjust the resolution.

• Windows 7: Go to Control Panel Appearance and Personalization Display Adjust

Resolution and adjust the resolution.

• Windows 8: Go to Settings Control Panel Appearance and Personalization Display

Adjust Resolution and adjust the resolution.

128

Question

How do I set powersaving mode?

Answer

• Windows XP: Set power-saving mode in Control Panel Appearance and Themes Display

Screen Saver Settings or BIOS SETUP on the PC.

• Windows ME/2000: Set power-saving mode in Control Panel Display Screen Saver

Settings or BIOS SETUP on the PC.

• Windows Vista: Set power-saving mode in Control Panel Appearance and Personalization

Personalize Screen Saver Settings or BIOS SETUP on the PC.

• Windows 7: Set power-saving mode in Control Panel Appearance and Personalization

Personalize → Screen Saver Settings or BIOS SETUP on the PC.

• Windows 8: Set power-saving mode in Settings Control Panel Appearance and

Personalization → Personalize Screen Saver Settings or BIOS SETUP on the PC.

129

Chapter 14

Specifications

- Size

- Display area

H

V

- Dimensions (W x H x D)

D

H

General

Model Name

Panel Size

Display area

Dimensions

(W x H x D /

Weight)

Audio Output

Power Supply

Without Stand

With Stand

Environmental considerations

Operating

Storage

RM40D

40 CLASS (40.0 inches / 101 cm)

RM48D

48 CLASS (47.6 inches / 121 cm)

885.6 mm (H) x 498.15 mm (V)

34.9 inches (H) x 19.6 inches (V)

906.6 x 532.9 x 65.1 mm / 7.6 kg

35.7 x 21.0 x 2.6 inches / 16.8 Ibs

906.6 x 578.2 x 196.4 mm / 8.6 kg

35.7 x 22.8 x 7.7 inches / 19.0 Ibs

10 W + 10 W

1054.08 mm (H) x 592.92 mm (V)

41.5 inches (H) x 23.3 inches (V)

1075.1 x 627.6 x 65.5 mm / 11.1 kg

42.3 x 24.7 x 2.6 inches / 24.5 Ibs

1075.1 x 673.8 x 203.9 mm / 12.3 kg

42.3 x 26.5 x 8.0 inches / 27.1 Ibs

AC 100 to 240 VAC (+/- 10%), 60 / 50 Hz ± 3 Hz

Refer to the label at the back of the product as the standard voltage can vary in different countries.

Temperature : 32 F ~ 104 F (0 C ~ 40 C)

Humidity : 10 % ~ 80 %, non-condensing

Temperature : -4 F ~ 113 F (-20 C ~ 45 C)

Humidity : 5 % ~ 95 %, non-condensing

W

130

― Plug-and-Play

This SMART Signage TV can be installed and used with any Plug-and-Play compatible systems.

Two-way data exchange between the SMART Signage TV and PC system optimizes the SMART Signage TV settings.

SMART Signage TV installation takes place automatically. However, you can customize the installation settings if desired.

― Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect product performance.

― This device is a Class A digital apparatus.

(USA only)

Dispose unwanted electronics through an approved recycler.

To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call, (877) 278 - 0799

[Recommendation] - EU Only

• Hereby, Samsung Electronics, declares that this Monitor is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

• The official Declaration of Conformity may be found at http://www.samsung.com/displaysolutions, go to Support >

Search Product Support and enter the model name.

• This equipment may only be used indoors.

• This equipment may be operated in all EU countries.

131

Power Consumption

The power-saving function of this product reduces power consumption by switching off the screen and changing the colour of the power LED if the product is not used for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse.

Power-savign mode only functions when the product is connected to a PC with a power-saving function.

Normal Operation

Typical Rating Max

Stand-by

Power Indicator Off On

Power Consumption RM40D

RM48D

64.4 W 89 W 98 W 0.5 W

74.6 W 104 W 114 W

― The displayed power consumption level can vary in different operating conditions or when settings are changed.

― SOG(Sync On Green) is not supported.

― To reduce the power consumption to 0, disconnect the power cord. Disconnect the power cable if you will not be using the product for an extended period of time (during vacation, etc.)

132

Horizontal Frequency

The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in kHz.

Vertical Frequency

The product displays a single image multiple times per second (like a fluorescent light) to display what the viewer sees. The rate of a single image being displayed repeatedly per second is called vertical frequency or refresh rate.

Vertical frequency is measured in Hz.

Preset Timing Modes

― This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product.

― Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product. If the LCD product does not support 85Hz, change the vertical frequency to 60Hz using the CDT product before you exchange it with the LCD product.

Model Name

Synchronization

RM48D

Resolution

Horizontal Frequency

Vertical Frequency

Optimum resolution

Maximum resolution

RM40D

30 ~ 81 kHz

48 ~ 75 Hz

1920 x 1080 @ 60 Hz

1920 x 1080 @ 60 Hz

The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signal transmitted from the PC does not belong to the standard signal modes, the screen may be blank with the power LED on. In such a case, change the settings according to the following table by referring to the graphics card user manual.

― PC mode is not support interlaced signal.

Resolution

VESA, 640 x 480

Horizontal Frequency

(kHz)

31.469

Vertical Frequency

(Hz)

59.940

Pixel Clock

(MHz)

25.175

Sync Polarity

(H/V)

-/-

IBM, 720 x 400

MAC, 640 x 480

MAC, 832 x 624

MAC, 1152 x 870

VESA, 640 x 480

31.469

35.000

49.726

68.681

37.861

70.087

66.667

74.551

75.062

72.809

28.322

30.240

57.284

100.000

31.500

-/-

-/-

-/-

-/+

-/-

133

Resolution

VESA, 640 x 480

VESA, 800 x 600

VESA, 800 x 600

VESA, 800 x 600

VESA, 1024 x 768

VESA, 1024 x 768

VESA, 1024 x 768

VESA, 1152 x 864

VESA, 1280 x 720

VESA, 1280 x 800

VESA, 1280 x 1024

VESA, 1280 x 1024

VESA, 1366 x 768

VESA, 1440 x 900

VESA, 1600 x 900

VESA, 1680 x 1050

VESA, 1920 x 1080

Horizontal Frequency

(kHz)

37.500

60.023

67.500

45.000

49.702

63.981

79.976

47.712

55.935

60.000

65.290

67.500

37.879

48.077

46.875

48.363

56.476

Vertical Frequency

(Hz)

75.000

75.029

75.000

60.000

59.810

60.020

75.025

59.790

59.887

60.000

59.954

60.000

60.317

72.188

75.000

60.004

70.069

Pixel Clock

(MHz)

31.500

78.750

108.000

74.250

83.500

108.000

135.000

85.500

106.500

108.000

146.250

148.500

40.000

50.000

49.500

65.000

75.000

-/+

+/+

+/+

+/+

-/+

+/+

+/+

+/+

+/+

-/+

+/+

+/+

+/+

+/+

-/-

-/-

Sync Polarity

(H/V)

-/-

134

Chapter 15

Appendix

Contact SAMSUNG WORLD WIDE

Web site: http://www.samsung.com/displaysolutions/signagetv

― If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.

NORTH AMERICA

U.S.A

1-866-SAM4BIZ

CANADA

1-800-749-0205

LATIN AMERICA

ARGENTINE

BOLIVIA

BRAZIL

CHILE

COLOMBIA

0800 333 3733

800-10-7260

0800-124-421 (Demais cidades e regiões)

4004-0000 (Capitais e grandes centros)

800-SAMSUNG (726-7864)

01 8000 112 112

Bogotá 600 12 72

135

LATIN AMERICA

COSTA RICA

DOMINICA

ECUADOR

EL SALVADOR

GUATEMALA

HONDURAS

JAMAICA

NICARAGUA

MEXICO

PANAMA

PARAGUAY

PERU

PUERTO RICO

TRINIDAD & TOBAGO

URUGUAY

0-800-507-7267

1-800-751-2676

1-800-10-7267

800-6225

1-800-299-0013

800-27919267

1-800-234-7267

001-800-5077267

01-800-SAMSUNG (726-7864)

800-7267

009 800 542 0001

0-800-777-08

1-800-682-3180

1-800-SAMSUNG (726-7864)

000 405 437 33

136

CZECH

DENMARK

EIRE

ESTONIA

FINLAND

FRANCE

LATIN AMERICA

VENEZUELA

EUROPE

AUSTRIA

BELGIUM

BOSNIA

BULGARIA

CROATIA

CYPRUS

0-800-100-5303

0810 - SAMSUNG (7267864, € 0.07/min)

02-201-24-18

051 331 999

07001 33 11 , share cost tariff

062 SAMSUNG (062 726 786)

8009 4000 only from landline

800 - SAMSUNG (800-726786)

Samsung Electronics Czech and Slovak, s.r.o. V Parku 2343/24, 148 00 - Praha 4

70 70 19 70

0818 717100

800-7267

030-6227 515

01 48 63 00 00

137

EUROPE

GERMANY

GREECE

HUNGARY

ITALIA

LATVIA

LITHUANIA

LUXEMBURG

MONTENEGRO

NETHERLANDS

NORWAY

POLAND

PORTUGAL

0180 6 SAMSUNG bzw.

0180 6 7267864*

(*0,20 €/Anruf aus dem dt. Festnetz, aus dem Mobilfunk max. 0,60 €/Anruf )

80111-SAMSUNG (80111 726 7864) only from land line

(+30) 210 6897691 from mobile and land line

06-80-SAMSUNG (726-7864)

800-SAMSUNG (726-7864)

8000-7267

8-800-77777

261 03 710

020 405 888

0900-SAMSUNG (0900-7267864) (€ 0,10/Min)

815 56480

0 801-172-678* lub +48 22 607-93-33 **

*(całkowity koszt połączenia jak za 1 impuls według taryfy operatora)

** (koszt połączenia według taryfy operatora)

808 20-SAMSUNG (808 20 7267)

138

CIS

ARMENIA

AZERBAIJAN

BELARUS

GEORGIA

KAZAKHSTAN

KYRGYZSTAN

MOLDOVA

EUROPE

ROMANIA

SERBIA

SLOVAKIA

SPAIN

SWEDEN

SWITZERLAND

U.K

08008 SAMSUNG (08008 726 7864) TOLL FREE No.

011 321 6899

0800 - SAMSUNG (0800-726 786)

902172678

0771 726 7864 (SAMSUNG)

0848 - SAMSUNG (7267864, CHF 0.08/min)

0330 SAMSUNG (7267864)

0-800-05-555

088-55-55-555

810-800-500-55-500

0-800-555-555

8-10-800-500-55-500 (GSM: 7799)

00-800-500-55-500

0-800-614-40

139

CIS

MONGOLIA

RUSSIA

TADJIKISTAN

UKRAINE

UZBEKISTAN

ASIA PACIFIC

AUSTRALIA

CHINA

HONG KONG

INDIA

INDONESIA

JAPAN

MALAYSIA

NEW ZEALAND

+7-800-555-55-55

8-800-555-55-55

8-10-800-500-55-500

0-800-502-000

8-10-800-500-55-500

1300 362 603

400-810-5858

(852) 3698 4698

1800 3000 8282

1800 266 8282

0800-112-8888 (Toll Free)

(021) 56997777

0120-327-527

1800-88-9999

0800 SAMSUNG (0800 726 786)

140

ASIA PACIFIC

PHILIPPINES

SINGAPORE

TAIWAN

THAILAND

VIETNAM

MENA

ALGERIA

BAHRAIN

EGYPT

IRAN

JORDAN

KUWAIT

MOROCCO

1-800-10-7267864 [PLDT]

1-800-8-7267864 [Globe landline and Mobile]

02-4222111 [Other landline]

1800-SAMSUNG (726-7864)

0800-32-9999

0-2689-3232,

1800-29-3232

1800 588 889

0800 100 100

8000-4726

08000-726786

021-8255

0800-22273

06 5777444

183-2255 (183-CALL)

080 100 2255

141

AFRICA

BOTSWANA

BURUNDI

CAMEROON

COTE D’ IVOIRE

DRC

GHANA

MENA

OMAN

PAKISTAN

QATAR

SAUDI ARABIA

SYRIA

TUNISIA

TURKEY

U.A.E

8007260000

200

7095-0077

8000 0077

499999

0800-10077

0302-200077

800-SAMSUNG (726-7864)

0800-Samsung (72678)

800-2255 (800-CALL)

920021230

18252273

80-1000-12

444 77 11

800-SAMSUNG (726-7864)

142

AFRICA

KENYA

NAMIBIA

NIGERIA

MOZAMBIQUE

RWANDA

SENEGAL

SOUTH AFRICA

SUDAN

TANZANIA

UGANDA

ZAMBIA

0800 545 545

08 197 267 864

0800-726-7864

847267864 / 827267864

9999

800-00-0077

0860 SAMSUNG (726 7864)

1969

0685 88 99 00

0800 300 300

0211 350370

143

Responsibility for the Pay Service

(Cost to Customers)

― When the service is requested, in spite of in warranty, we may charge you for a visit from a service technician in the following cases.

Not a product defect

Cleaning of the product, Adjustment, Explanation, Re-installation and etc.

• If a service technician gives instructions on how to use product or simply adjusts options without disassembling product.

• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)

• If a product is reinstalled or devices are connected additionally after installing the purchased product for the first time.

• If a product is reinstalled to move to a different spot or to move to a different house.

• If customer requests instructions on how to use because of another company's product.

• If customer requests instructions on how to use the network or another company's programme.

• If customer requests software installation and setup for the product.

• If a service technician removes/cleans dusts or foreign materials inside of the product.

• If customer requests an installation additionally after purchasing a product through home-shopping or online.

A Product damage caused by customer's fault

Product damage caused by customer's mishandling or wrong repair

If a product damage is caused by;

• External impact or drop.

• Use of supplies or separatly sold product unspecified by Samsung.

• Repair from a person besides an engineer of outsourcing service company or partner of Samsung

Electronics Co., Ltd.

• Remodeling or repairing the product by customer.

• Using it with incorrect voltage or non-authorised electrical connections.

• Not following the "cautions" in User Manual.

Others

• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)

• If consumable components are all used up.

(Battery, Toner, Fluorescent lights, Head, Vibrator, Lamp, Filter, Ribbon, etc.)

― If customer requests a service in case the product has no defect, service fee may be charged.

So please read User Manual first.

144

WEEE

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.

To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Correct disposal of batteries in this product

(Applicable in countries with separate collection systems)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66.

If batteries are not properly disposed of, these substances can cause harm to human health or the environment.

To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.

145

Optimum Picture Quality and Afterimage

Burn-in Prevention

Optimum Picture Quality

Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be brighter or darker on the panel.

This does not affect product performance.

The number of sub-pixels by panel type: 6,220,800

• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels.

Activate power-saving mode or a dynamic screen saver if you will not be using the product for an extended period of time.

Prevention of Afterimage Burn-in

What is afterimage burn-in?

Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period of time (more than 12 hours), a slight voltage difference may occur between the electrodes in pixels that control the liquid crystals.

Such a voltage difference between electrodes increases with time and makes the liquid crystals thinner.

When this occurs, a previous image can remain on the screen when the pattern changes. To prevent this, the accumulated voltage difference should be reduced.

― Afterimage burn-in should not occur when an LCD panel is operating in proper conditions.

Black Matrix

Source Drain

TFT

Data Bus-Line

Gate

Common

Electrode (ITO)

Color-Filter

Pixel Electrode (ITO)

Storage

Capaccitor (Cs)

146

Preventing afterimage burn-in

― The best way to protect the product from afterimage burn-in is switching the power off or setting the

PC or system to run a screen saver when not in use. Also, Warranty service may be limited depending on instruction guide.

• Powering Off, Screen Saver and Power Saving Mode

Go to Display Properties > Power Supply on your PC and set the product to power off as required.

Using a screen saver is recommended.

It is best to use a single-color or moving-image screen saver.

• Regular color Change

Use 2 colors

Switch between 2 colors every 30 minutes as shown above.

Type 1

FLIGHT

OZ348

TIME

20:30

UA102 21:10

Type 2

FLIGHT

OZ348

TIME

20:30

UA102 21:10

• Avoid combinations of a text color and background color of contrasting brightness.

(Brightness: refers to the lightness or darkness of a color which varies depending on the amount of light emitted.)

― Avoid using grey as it may contribute to afterimage burn-in.

― Avoid using colors of contrasting brightness (black and white; grey).

FLIGHT : TIME

OZ348 : 20:30

FLIGHT : TIME

OZ348 : 20:30

• Regular Text color Change

Use bright colors of similar brightness.

Interval: Change text color and background color every 30 minutes

FLIGHT : TIME

OZ348 : 20:30

FLIGHT : TIME

OZ348 : 20:30

FLIGHT : TIME

OZ348 : 20:30

FLIGHT

OZ348 :

: TIME

20:30

Move and change text every 30 minutes as shown below.

FLIGHT

OZ348 :

: TIME

20:30

[ Step 1 ] [ Step 2 ]

FLIGHT

OZ348 :

: TIME

20:30

[ Step 3 ]

Regularly display a moving image along with a logo.

Interval: Display a moving image along with a logo for 60 seconds after using for 4 hours.

147

Licence

Manufactured under licence from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby Laboratories.

2.0 Channel

Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380;

6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the

Symbol, & DTS and the Symbol together are registered trademarks & DTS 2.0

Channel is a trademark of DTS, Inc. ⓒ DTS, Inc. All Rights Reserved.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the

HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

DivX Certified Ⓡ to play DivX Ⓡ video up to HD 1080p, including premium content.

DivXⓇ, DivX CertifiedⓇ and associated logos are trademarks of Rovi

Corporation or its subsidiaries and are used under license.

ABOUT DIVX VIDEO: DivXⓇ is a digital video format created by DivX, Inc. This is an official DivX

CertifiedⓇ device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video.

ABOUT DIVX VIDEO-ON-DEMAND: This DivX CertifiedⓇ device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the

DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.

Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274

Open Source Licence Notice

In the case of using open source software, Open Source Licences are available on the product menu.

Open Source Licence Notice is written only English.

For information on the Open Source Licence Notice, contact the Samsung Customer Centre or send email to [email protected].

148

Terminology

480i / 480p / 720p / 1080i /

1080p____ Each of the scanning rates above refers to the number of effective scanning lines that decides the screen resolution. The scanning rate may be indicated in i (interlaced) or p (progressive), depending on the scanning method.

- Scanning

Scanning refers to a process of sending pixels that form an image progressively.

A larger number of pixels will deliver a clearer and more vivid picture.

- Progressive

In progressive scan mode, all lines of pixels are scanned one by one

(progressively) on the screen.

- Interlaced

In interlaced scan mode, every other line of pixels is scanned from top to bottom first and then the remaining lines of pixels (that were not scanned) are scanned.

Non-interlace Mode and Interlace

Mode____ Non-interlace mode

(progressive scan) displays a horizontal line from the top to the bottom of a screen progressively. Interlace mode displays the odd number lines first and the even number lines next. Noninterlace mode is mainly used in monitors as it produces screen clarity and interlace mode is mainly used in

TVs.

Dot Pitch____ The screen consist of red, green and blue dots. A shorter distance between the dots produces a higher resolution. Dot pitch refers to the distance between the shortest distance between dots of the same colour. Dot pitch is measured in millimeters.

Vertical Frequency____ The product displays a single image many times per second (like a fluorescent light that flickers) to display an image for a viewer to see. The rate of a single image being displayed repeatedly per second is called vertical frequency or refresh rate.

Vertical frequency is measured in Hz.

E.g. 60Hz refers to a single image being displayed 60 times in one second.

Horizontal Frequency____ The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in kHz.

Source____ Input source refers to a video source device connected to the product such as a camcorder or video or DVD player.

Plug & Play____ Plug & Play is a function that allows the automatic exchange of information between a

SMART Signage TV and PC to produce an optimum display environment. The product uses VESA DDC (international standard) to execute Plug & Play.

Resolution____ Resolution is the number of horizontal dots (pixels) and vertical dots (pixels) that form a screen.

It represents the level of display detail.

A higher resolution enables more data to be displayed on the screen and is useful to perform multiple tasks simultaneously.

E.g. A resolution of 1920 X 1080 consists of 1,920 horizontal pixels (horizontal resolution) and 1,080 vertical pixels

(vertical resolution).

DVD (Digital Versatile Disc)____ DVD refers to a CD-sized mass storage disk where you can save multimedia (audio, video or game) applications using

MPEG-2 video compression technology.

HDMI (High Definition Multimedia

Interface)____ It is an interface that can be connected to a digital audio source as well as a high-definition video source by using a single cable without compression.

Multiple Display Control (MDC)____

MDC (Multiple Display Control) is an application that allows multiple display devices to be controlled simultaneously using a PC. Communication between a PC and monitor takes place using

RS232C (serial data transmission) and

RJ45 (LAN) cables.

149

advertisement

Related manuals

Download PDF

advertisement