Panasonic | BB-GT1540E | User manual | Operating Instructions BB-GT1520E BB-GT1522E BB - Psn

Add to my manuals
112 Pages

advertisement

Panasonic | BB-GT1540E | User manual | Operating Instructions BB-GT1520E BB-GT1522E BB - Psn | Manualzz

GT15xxE.book Page 1 Wednesday, August 1, 2007 11:59 AM

Operating Instructions

Global VoIP Telephone

Model No.

BB-GT1500E

BB-GT1520E

BB-GT1522E

BB-GT1540E

BB-GT1500E

This unit is compatible with Caller ID. To use this feature, you must subscribe to the A service offered by deltathree, Inc. or the appropriate service offered by your landline service provider.

Charge the handset battery for 7 hours before initial use.

Please read these Operating Instructions before using the unit and save for future reference.

GT15xxE.book Page 2 Wednesday, August 1, 2007 11:59 AM

Table of Contents

Introduction

Product information . . . . . . . . . . . . . . . 3

Accessory information . . . . . . . . . . . . . 7

Symbols used in these operating instructions . . . . . . . . . . . . . . . . . . . . 10

Important Information

Important information . . . . . . . . . . . . 11

Security caution. . . . . . . . . . . . . . . . . 12

Preparation

Controls (Base unit). . . . . . . . . . . . . . 14

Controls (Handset) . . . . . . . . . . . . . . 17

Installation . . . . . . . . . . . . . . . . . . . . . 18

Battery charge. . . . . . . . . . . . . . . . . . 21

Understanding the indicators on the base unit . . . . . . . . . . . . . . . . . . . . . . 23

Displays. . . . . . . . . . . . . . . . . . . . . . . 26

Setting the unit before use . . . . . . . . 29

Making/Answering Calls

(Handset)

Making calls. . . . . . . . . . . . . . . . . . . . 32

Answering calls . . . . . . . . . . . . . . . . . 33

Useful features during a call . . . . . . . 33

Making/Answering Calls

(Base Unit)

Making calls. . . . . . . . . . . . . . . . . . . . 36

Answering calls . . . . . . . . . . . . . . . . . 36

Useful features during a call . . . . . . . 37

Making Internet Calls (Mobile

Phone)

Making internet calls using your mobile phone . . . . . . . . . . . . . . . . . . . . . . . . 39

Handset Phonebook

Handset phonebook . . . . . . . . . . . . . 40

Base Unit Speed Dialler

Base unit speed dialler . . . . . . . . . . . 43

Caller ID Service

Using Caller ID service . . . . . . . . . . . 44

Caller list . . . . . . . . . . . . . . . . . . . . . . 45

Programming

Programmable settings . . . . . . . . . . 47

Answering System

Answering system . . . . . . . . . . . . . . 60

Greeting message . . . . . . . . . . . . . . 61

Listening to messages using the base unit . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Listening to messages using the handset. . . . . . . . . . . . . . . . . . . . . . . 62

Voice memo . . . . . . . . . . . . . . . . . . . 63

Remote operation. . . . . . . . . . . . . . . 64

Answering system settings. . . . . . . . 66

Voice Mail Service

Using Voice Mail service . . . . . . . . . 68

Intercom Features

Intercom features between handsets 69

Intercom features between the handset and base unit . . . . . . . . . . . . . . . . . . 70

A Service

Using A service features . . . . . . . 73

Useful Information

Belt clip. . . . . . . . . . . . . . . . . . . . . . . 76

Wall mounting for charger . . . . . . . . 76

Registering a handset . . . . . . . . . . . 77

IP RESET button . . . . . . . . . . . . . . . 78

Character entry. . . . . . . . . . . . . . . . . 79

Error messages . . . . . . . . . . . . . . . . 81

Troubleshooting . . . . . . . . . . . . . . . . 84

Open Source Software . . . . . . . . . . . 92

Specifications . . . . . . . . . . . . . . . . . 102

Conditions of guarantee . . . . . . . . . 103

Customer services . . . . . . . . . . . . . 104

Index

Index. . . . . . . . . . . . . . . . . . . . . . . . 107

2

GT15xxE.book Page 3 Wednesday, August 1, 2007 11:59 AM

Product information

Thank you for purchasing a Panasonic GLOBARANGE phone.

These operating instructions can be used for the following models:

BB-GT1500

BB-GT1520

Introduction

BB-GT1522

BB-GT1540

Important:

L

The suffix (E) in the following model numbers will be omitted in these instructions:

BB-GT1500E/BB-GT1520E/BB-GT1522E/BB-GT1540E

Notable feature differences between models

Model no.

BB-GT1500

BB-GT1520

BB-GT1522

BB-GT1540

Answering system

– r r r

Intercom

f

N

*1

– r r r

N

N

*2

r r r r

*3

*3

*3

Make/answer calls with base unit

– r

*1 Intercom calls can be made between the handset and base unit.

*2 Intercom calls can be made between the handsets.

*3 Intercom calls can be made between the handsets by purchasing and registering

1 or more optional handsets (BB-GTA150E, page 9).

How the GLOBARANGE phone works

Connect this phone to both a landline and the Internet (IP line) so you can make or receive internet calls as well as landline calls.

When you make calls with A, a VoIP (Voice over Internet Protocol) service, your voice will be sent as data packets over the Internet to the person you are calling

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

3

GT15xxE.book Page 4 Wednesday, August 1, 2007 11:59 AM

Introduction

converted into voice. Basically, you can make internet calls using the A service virtually the same as using a landline. For more information, see “What is A/A number?” below and visit www.joip.com

Modem Router

IP line

Internet

Computer

(optional) *2

PSTN

(Public Switched

Telephone Network)

Landline

(PSTN line)

GLOBARANGE phone *1

*1 Model shown is BB-GT1500.

*2 Computer is not required for setup or making/answering internet calls.

What is A/A number?

A is the VoIP service provided by deltathree Inc. After connecting this phone to the

Internet (page 18, 30), a unique A number is sent to your handset display (page

31), so you can use your IP line as follows:

1. Make and receive free calls to and from other A numbers for a full period of 3 years from the date of setup.

*1*2

2. Make calls from your A number to landline and mobile phones at very low rates by subscribing to the appropriate service at www.joip.com

3. Receive calls from landline and mobile phone numbers via your IP line by subscribing for additional phone number(s) at www.joip.com

These additional phone numbers can be chosen regardless of your geographic location from a list of international and local area codes offered by A. There may be restrictions in obtaining phone numbers from certain countries or areas.

Visit www.joip.com for details.

A A number consists of a # followed by 10 digits, enabling you to make and receive free calls to and from other A number owners for a full period of 3 years

from the date of setup.

*1*2

The A number does not involve extra charges and is given free to Panasonic

GLOBARANGE phone owners.

*1 Requires both parties to have a Panasonic GLOBARANGE Phone, activated the

A service from deltathree, Inc., and broadband internet service provided by a cable company or internet service provider for a fee.

*2 After 3 years, the A service may require a fee.

4

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 5 Wednesday, August 1, 2007 11:59 AM

Introduction

Important:

For A services, please visit the A website: www.joip.com or contact the A service provider.

L

Terms of Use for the A services are available on the supplied leaflet or at www.joip.com and must be read and accepted prior to using A services.

L

NEITHER PANASONIC COMMUNICATIONS CO., LTD., PANASONIC SALES

COMPANIES NOR PANASONIC SALES AGENCIES IS IN ANY WAY

AFFILIATED WITH, OR RESPONSIBLE FOR THE ACTS OR OMISSIONS OF,

DELTATHREE, INC. NEITHER PANASONIC COMMUNICATIONS CO., LTD.,

PANASONIC SALES COMPANIES, PANASONIC SALES AGENCIES NOR ANY

OF THEIR EMPLOYEES OR AFFILIATES OR CUSTOMERS MAKE ANY

WARRANTIES OR REPRESENTATIONS, EITHER EXPRESS OR IMPLIED, TO

ANY CUSTOMER OR ANY OTHER THIRD PARTY WITH RESPECT TO ANY OF

THE SERVICES PROVIDED BY DELTATHREE, INC., NOR ASSUME NOR

CREATE ANY OTHER OBLIGATION OF ANY KIND ON BEHALF OF

DELTATHREE, INC.

L

In the event that your unit requires service within or outside of the Limited

Warranty, Panasonic will not be responsible for any loss of ringtones or other information previously downloaded, including the cost to repurchase such ringtones or other information.

For emergency calls, use the landline.

L

Even if you select the IP line, the landline is automatically used when dialling emergency phone numbers.

Note:

L

We recommend installing only one Panasonic GLOBARANGE phone base unit. If you install more than one Panasonic GLOBARANGE phone base unit, you may not be able to make or receive internet calls properly.

L

Sound quality and overall performance of IP phone may vary depending on the

condition of your network connection. Refer to “Troubleshooting”, page 89.

Trademarks

L deltathree and A are either registered trademarks or trademarks of deltathree,

Inc., in the United States and/or other countries.

L

All other trademarks identified herein are the property of their respective owners.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

5

GT15xxE.book Page 6 Wednesday, August 1, 2007 11:59 AM

Introduction

Feature highlights

Free calls to other A service subscribers (Panasonic GLOBARANGE

phone owners) for a full period of 3 years from the date of setup

*1

High quality IP telephony using your Internet connection

Enjoy high-quality calls at low rates to any destination worldwide using the A service.

Standard phone using a landline

Expandable phone system (up to 6 total handsets)

*2

Allows you to make an internet call on one handset while another handset is talking on the landline.

Save 100 phonebook items on a handset

Phonebook/Ringtone data downloading

Easily edit the phonebook items from a computer using the A website

(www.joip.com). Download phonebook items and ringtones to the base unit, then import them to a handset.

Internet call ability using a mobile phone via the unit’s answering system

(BB-GT1520/BB-GT1522/BB-GT1540)

*3

*1 After 3 years, the A service may require a fee.

*2 Requires optional additional handsets (sold separately, page 9).

*3 Requires subscription for additional phone number(s) for your A IP line other

than the A number (page 4).

Note:

L

A, a service powered by deltathree, Inc., offers special features such as Caller

ID, Call Waiting, and Voice Mail. For more information, visit the A website

(www.joip.com).

L

Your landline service provider may offer special telephone services such as Caller

ID, Call Waiting, and Voice Mail. Please contact your landline service provider for details and availability in your area.

6

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 7 Wednesday, August 1, 2007 11:59 AM

Introduction

System requirements

Your network must meet the following technical specifications for the unit to work as an IP phone.

Item

Internet connection

Modem

Description

Broadband Internet connection such as DSL or cable

Router

Broadband modem with Ethernet port (USB-only modems are not supported.)

Broadband router

*1*2

*1 This unit is not compatible with the following:

– PPPoE (Point to Point Protocol over Ethernet)

– PPTP (Point-to-Point Tunneling Protocol)

– L2TP (Layer 2 Tunneling Protocol)

If your Internet service provider uses a PPPoE, PPTP, or L2TP connection, a compatible router is required.

*2 This unit is designed to obtain an IP address automatically from a DHCP (Dynamic

Host Configuration Protocol) server. We recommend using the DHCP server

(page 30).

Accessory information

Supplied accessories

No.

Accessory item Order number

1

2

3

4

5

6

7

PQLV203EZ

(PQLV203E)

PQJA87S

(for UK)

HHR-P107

PQYNGTA150BR

PQJA10181Z

Quantity

BB-GT1500/

BB-GT1520/

BB-GT1540

1 AC adaptor for base unit

Telephone line cord

Battery

Handset cover

*1

Ethernet cable

(Category 5E straight cable)

Belt clip

Charger

1

1

1

1

PQKE10478Z2

PQLV30054N

1

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

BB-GT1522

1

1

2

2

1

2

1

7

GT15xxE.book Page 8 Wednesday, August 1, 2007 11:59 AM

Introduction

No.

Accessory item Order number

8

AC adaptor for charger

PQLV208EZ

(PQLV208E)

*1 The handset cover comes attached to the handset.

Quantity

BB-GT1500/

BB-GT1520/

BB-GT1540

1

2

3

4

BB-GT1522

1

5

6

7 8

8

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 9 Wednesday, August 1, 2007 11:59 AM

Introduction

Additional/replacement accessories

Please contact your nearest Panasonic dealer for sales information.

No.

1

2

3

4

3

Accessory item Order number

Rechargeable nickel metal hydride (Ni-MH) battery HHR-P107

Additional handset with charger

Headset

Wall mounting adaptor for base unit

BB-GTA150E

KX-TCA94EX

PQZMGT1500

4

Expanding your phone system

You can expand the phone system by registering optional handsets to a single base unit.

L

A maximum of 6 total handsets (supplied and optional) can be registered to a single base unit.

Handset (optional): BB-GTA150E

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

9

GT15xxE.book Page 10 Wednesday, August 1, 2007 11:59 AM

Introduction

Symbols used in these operating instructions

Symbol

l k

N f

{

} i

“ ”

{V}

/{^}: “ ”

{>}

/{<}/{<}/{>}

(BB-GT1520/

BB-GT1522/

BB-GT1540)

{

6}

(BB-GT1520/

BB-GT1522/

BB-GT1540)

Meaning

Features and operations for using the IP line

Features and operations for using the landline

Perform with the handset.

Perform with the base unit.

The words in the brackets indicate button names on the handset and base unit.

Proceed to the next operation.

The words in quotations indicate the menu on the display.

Example: “Ringer ID”

Push the handset joystick down or up to select the words in quotations.

Example: {V}/{^}: “Off”

Press up, down, left, or right on the base unit navigator key.

Press the centre of the base unit navigator key.

10

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 11 Wednesday, August 1, 2007 11:59 AM

Important information

General

L

Use only the AC adaptor supplied with

this product, noted on page 7.

L

Do not connect the AC adaptor to any

AC outlet other than a standard 220–

240 V AC outlet.

L

Do not open the base unit, charger, or handset other than to replace the battery(ies).

L

This product should not be used near emergency/intensive care medical equipment and should not be used by people with pacemakers.

L

Care should be taken that objects do not fall onto, and liquids are not spilled into, the product. Do not subject this product to excessive smoke, dust, mechanical vibration or shock.

Environment

L

Do not use this product near water.

L

This product should be kept away from heat sources such as radiators, cookers, etc. It should also not be placed in rooms where the temperature is less than 5 °C or greater than 40 °C.

L

The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible.

Warning:

L

To prevent the risk of electrical shock, do not expose this product to rain or any other type of moisture.

L

Unplug this product from power outlets if it emits smoke, an abnormal smell, or makes unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has

Important Information

stopped emitting and contact an authorised service centre.

L

Do not spill liquids (detergents, cleansers, etc.) onto the telephone line cord plug, or allow it to become wet at all. This may cause a fire. If the telephone line cord plug becomes wet, immediately pull it from the telephone wall jack, and do not use.

L

Do not place or use this product near automatically controlled devices such as automatic doors and fire alarms.

Radio waves emitted from this product may cause such devices to malfunction resulting in an accident.

L

Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire.

L

Do not damage the power cord/plug.

This may cause a short circuit, electric shock, and/or fire.

L

Do not touch the plug with wet hands.

Battery caution

L

We recommend using the battery(ies)

noted on page 9. Use only

rechargeable battery(ies).

L

Do not dispose of the battery(ies) in a fire, as they may explode. Check with local waste management codes for special disposal instructions.

L

Do not open or mutilate the battery(ies). Released electrolyte from the battery(ies) is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.

L

Exercise care when handling the battery(ies). Do not allow conductive materials such as rings, bracelets or keys to touch the battery(ies), otherwise a short circuit may cause

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

11

GT15xxE.book Page 12 Wednesday, August 1, 2007 11:59 AM

Important Information

the battery(ies) and/or the conductive material to overheat and cause burns.

L

Charge the battery(ies) in accordance with the information provided in these operating instructions.

L

Only use the supplied base unit (or charger) to charge the battery(ies). Do not tamper with the base unit (or charger). Failure to follow these instructions may cause the battery(ies) to swell or explode.

No responsibility will be taken by our company with respect to consequences resulting from the inappropriate use, damage or both of the unit.

Information on Disposal for Users of

Waste Electrical & Electronic

Equipment (private households)

details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European

Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other

Countries outside the European

Union

This symbol is only valid in the European

Union.

If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product.

Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further

Security caution

When using this product, take appropriate measures to avoid the following security breaches.

L

Leaks of private information via this product

L

Illegal use of this product by a third party

L

Interference or suspension of the use of this product by a third party

Take the following measures to avoid security breaches:

L

To prevent illegal access, keep the base unit software updated (if you do not have the latest version of software, this can lead to blocked

access or information leaks) (page

57).

12

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 13 Wednesday, August 1, 2007 11:59 AM

Important Information

L

You are responsible for the security settings, such as the remote code for the answering system, to access this product. This information should not be made available to any third parties outside the user group. To prevent unauthorised access to this product, we recommend that you regularly

change the remote code (page 64).

L

Place this product where it is unlikely to be stolen.

L

During an internet call, outside interference may occur resulting in improper call transmission and/or unit function.

Notice for product disposal, transfer, or return

L

This product can store your private/confidential information. To protect your privacy/confidentiality, we recommend that you erase the information such as phonebook or caller list entries from the memory before you dispose, transfer or return the product.

– Erasing caller list information (page

46)

– Erasing phonebook information

(page 41)

– Erasing messages (page 62, 74)

L

When transferring this product to another party or disposing of this product, be sure to cancel the service contract with A at www.joip.com if you subscribed to optional A services.

Routine care

L

To clean the product, use a dry soft cloth. The outer surface of the product can be scratched by wiping or rubbing with a hard cloth.

L

Do not use benzine, thinner, or any abrasive powder.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

13

GT15xxE.book Page 14 Wednesday, August 1, 2007 11:59 AM

Preparation

Controls (Base unit)

BB-GT1500

A B C D

Bottom view

IP RESET

E F

G

A IP indicator

B TEL indicator

C 4 (Status) indicator

D 0 (Voice Mail) indicator

E Charge contacts

F {x} (Page)

G {IP RESET}

*1

*1 You can locate a misplaced handset by pressing {x}. To stop paging, press it again or {i} on the handset.

14

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 15 Wednesday, August 1, 2007 11:59 AM

BB-GT1520/BB-GT1522

A B C D

G

Preparation

E F

Bottom view

IP RESET

S

H I J K L M N O P Q R

A IP indicator

B TEL indicator

C 4 (Status) indicator

D 0 (Voice Mail) indicator

E {IP/TEL}

F {s} (Answer on)/Answer on indicator

G Speaker

H Charge contacts

I {x} (Page/Intercom)

J {7} (Memo)

K {■} (Stop)

L Microphone

M Navigator key ({>}/{<}/{<}/{>})

N {6} (Message)/Message indicator

O {4} (Erase)

P {dr} (Greeting record)

Q {d>} (Greeting check)

R Display

S {IP RESET}

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

15

GT15xxE.book Page 16 Wednesday, August 1, 2007 11:59 AM

Preparation

BB-GT1540

A B C D E F

G H I J

Bottom view

IP RESET

!

K L M N O P Q R S T U V W X Y

Z

A {IP} (IP line)

IP indicator

B {TEL} (Landline)

TEL indicator

C {IP/TEL}

D 4 (Status) indicator

E 0 (Voice Mail) indicator

F {s} (Answer on)

Answer on indicator

G {x} (Page/Intercom)

H {l} (Auto/Program)

I {5} (Conference)

J {a} (Hold)

K Speaker

L Charge contacts

M {*}

N {R} (Pause/Redial)

O {6} (Recall)

P {T} (Mute)

16

Q {s} (Speakerphone)

Speakerphone indicator

R Microphone

S Navigator key

({>}/{<}/{<}/{>})

T {6} (Message)

Message indicator

U {■} (Stop)

V {4} (Erase)

W {7} (Memo)

X {dr} (Greeting record)

Y {dg} (Greeting check)

Z Display

! {IP RESET}

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 17 Wednesday, August 1, 2007 11:59 AM

Controls (Handset)

J

Preparation

Using the joystick

The handset joystick can be used to navigate through menus and to select items shown on the display, by pushing it up {^}, down {V}, left {<}, or right {>}.

K

A

B

C

D

E

F

G

H

I

L

B

M

N

O

The joystick can be used to select the centre soft key icon, by pressing down on the centre of the joystick.

A Speaker

B Soft keys

C Headset jack

D {IP} (IP line)

E Joystick

F {s} (Speakerphone)

G {R} (Redial/Pause)

H {*}

I {6} (Recall)

J Charge indicator

Ringer indicator

Message indicator

K Receiver

L Display

M {TEL} (Landline)

N {i} (Off)

O {a} (Hold)

{

INT} (Intercom)

P Microphone

Q Charge contacts

P

Q

Using the soft keys

The handset features 2 soft keys and a joystick. By pressing a soft key, or by pressing the centre of the joystick, you can select the feature shown directly above it on the display.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

17

GT15xxE.book Page 18 Wednesday, August 1, 2007 11:59 AM

Preparation

Installation

Connecting to a landline and the Internet (IP line)

Connect the base unit to a broadband router or modem with a built-in router.

*1 Computer is not required for setup or making/answering internet calls.

Press plug firmly.

TEL LAN

AC adaptor

3

Hook

To AC mains outlet

(220-240 V, 50 Hz)

Internet

Router

Cable or

DSL modem

Ethernet cable

2

1

Computer

(Optional) *1

Telephone line cord

To telephone network

1

Connect the supplied Ethernet cable until it clicks into the “LAN” port on the base unit and unused Ethernet (LAN) port on your router or modem with a built-in router.

2

Connect the supplied telephone line cord until it clicks into the “TEL” port on the base unit and telephone line jack.

3

Connect the supplied AC adaptor to the base unit by pushing the plug firmly, then plug the other end into the AC outlet.

L

Use only the supplied Panasonic AC adaptor.

L

The 4 indicator on the base unit lights in red for about 3 seconds (page 23).

18

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 19 Wednesday, August 1, 2007 11:59 AM

Preparation

4

Install the battery:

Press the notch of the handset cover firmly, and slide it in the direction of the arrow (

A). Insert the battery (B), and press it down until it snaps into position

(

C). Then close the handset cover (D, E).

A

B

C

E

D

5

Charge the battery:

Place the handset on the base unit.

L

If “Charge for 7 HRS” is displayed, wait for at most 15 minutes until

“Please read joip Terms of Use. Agree?” is displayed.

L

To fully charge the battery, place the handset on the base unit for 7 hours. For

battery information, see page 21.

Confirm the charge indicator is on.

Please read joip

Terms of Use.

Agree?

O K

[

Model shown is BB-GT1500.

6

Agree to the A Terms of Use:

To use the A IP line, read the Terms of Use for the A services on the supplied leaflet or at www.joip.com then press M (left soft key) while “Please

read joip Terms of Use. Agree?” is displayed.

L

To agree to the Terms of Use later, press W. When you want to agree, press

{

IP} and wait until the display changes from “Free calls! Plug

internet cable. www.joip.com” to “Please read joip Terms of

Use. Agree?”. Press M to agree to it.

7

Check for Internet access:

Wait until the 4 indicator on the base unit turns green.

– When the 4 indicator on the base unit lights in green, the installation is complete. Your A number is displayed on the handset 1 (supplied with your base unit). Once you start operations with the handset, it disappears from the

display (page 31).

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

19

GT15xxE.book Page 20 Wednesday, August 1, 2007 11:59 AM

Preparation

– When the 4 indicator on the base unit does not light in green even if you wait

for a few minutes, see page 24.

Amber Green

Your

A number

joip:#1001060429

Set Date & Time

Model shown is

BB-GT1500.

Note:

L

Never install telephone wiring during a lightning storm.

L

The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)

L

The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected.

L

The unit will not work during a power failure. To use the landline, we therefore recommend you also connect a corded-type telephone (without AC adaptor) to the same telephone line using a T-adaptor. Your Panasonic sales shop can offer you more information about connection possibilities.

Location

L

For maximum distance and noise-free operation, place your base unit:

– away from electrical appliances such as TVs, radios, personal computers or other phones.

– in a convenient, high and central location.

Connecting the AC adaptor (BB-GT1522)

To AC mains outlet

(220-240 V, 50 Hz) Bottom of the charger

Hooks

Hooks

Fasten the AC adaptor cord to prevent it from being disconnected.

20

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 21 Wednesday, August 1, 2007 11:59 AM

Battery charge

Battery charge

To fully charge the battery, place the handset on the base unit or charger for 7

hours.

L

While charging, the charge indicator on the handset lights in amber. When the battery is fully charged, the indicator lights in green.

Base unit

Preparation

Note:

L

It is normal for the handset to feel warm during charging.

L

If you want to use the handset immediately, charge the battery for at least 15 minutes.

L

To ensure that the battery charges properly, clean the charge contacts of the handset, base unit, and charger with a soft, dry cloth once a month.

Clean more often if the unit is subject to the exposure of grease, dust, or high humidity.

Charge contacts

L

Model shown is BB-GT1500.

Charger

Available model:

BB-GT1522

Charge contacts

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

21

GT15xxE.book Page 22 Wednesday, August 1, 2007 11:59 AM

Preparation

Battery level

Battery icon

1

2

3

Battery level

Fully charged

Medium

Low

Flashing: needs to be recharged.

Empty

4

Note:

L

When the battery needs to be charged, the handset beeps intermittently during use.

Panasonic battery performance

Operation

While in use

(talking)

While not in use

(standby)

Operating time

Up to 8 hours

Up to 14 days

Note:

L

It is normal for the battery not to reach full capacity at the initial charge.

Maximum battery performance is reached after a few complete cycles of charge/discharge (use).

L

Battery operating time may be shortened over time depending on usage conditions and surrounding temperature.

L

Battery power is consumed whenever the handset is off the base unit or charger, even when the handset is not in use.

L

After the handset is fully charged, displaying “Charge completed”, it may be left on the base unit or charger without any ill effect on the battery.

L

The battery level may not be displayed correctly after you replace the battery. In this case, place the handset on the base unit or charger and let it charge for 7 hours.

Battery replacement

Important:

L

Use only the rechargeable Panasonic

battery noted on page 9.

Replace the old battery with a new one.

See page 19, step 4.

22

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 23 Wednesday, August 1, 2007 11:59 AM

Preparation

Understanding the indicators on the base unit

TEL indicator/IP indicator

The TEL indicator and IP indicator show the status of the landline and IP line, respectively, as follows.

Status

Light off

Light on

Flashing rapidly

Flashing

Meaning

The line is available.

The line is in use.

*1

A call is being received.

A call is put on hold.

The answering system is answering a call.

(BB-GT1520/BB-GT1522/BB-GT1540)

The IP indicator flashes when the base unit software is being downloaded from the A service.

*1 k When another phone uses the same landline, the TEL indicator lights.

4

(Status) indicator

During the startup process you may notice that the 4 indicator on the base unit is flashing. This indicates that the base unit is booting up with the A service. You may find the following flash patterns helpful to you:

Status

Colour

Green

Red

Meaning

Light pattern

On

Flashing

On

Flashing

Flashing rapidly

L

The base unit is connected to the Internet. The startup process is complete and you may now make and receive A internet calls.

L

The base unit is downloading data from the A service. Do not disconnect the Ethernet cable or AC adaptor from the base unit until the 4 indicator stops flashing and lights in steady green.

L

When the base unit is turned on, the 4 indicator lights in red for about 3 seconds.

L

The base unit is registering a handset.

L

The base unit is paging handsets.

(BB-GT1500)

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

23

GT15xxE.book Page 24 Wednesday, August 1, 2007 11:59 AM

Preparation

Status

Colour

Amber

Meaning

Light pattern

On

Flashing

Flashing rapidly

L

The base unit’s IP address may conflict with the IP addresses of other devices on your local network.

Check the base unit’s static IP address using the handset: K i {#}{5}{0}{1}, then check the IP addresses of the other devices on your local network. If necessary, change the base unit’s static

IP address (page 30).

L

The base unit is obtaining an IP address or is obtaining configurations from the A service.

Please wait.

L

The base unit is registering with the A service.

Please wait.

L

If the 4 indicator continues flashing, check the following:

– Check the base unit’s IP address using the handset: K i {#}{5}{0}{1}

If necessary, change the base unit’s static IP

address (page 30).

– If an IP address was not acquired, check your network devices’ (router, modem, etc.) connections. If the connections are made properly but the problem persists, check your network devices’ (router, modem, etc.) settings.

– Many installation issues can be resolved by resetting all the equipment. First, shut down your modem, router, base unit, and computer. Then turn the devices back on one at a time in this order: modem, router, base unit, computer.

– If you cannot access Internet Web pages using your computer, check to see if your Internet service provider is having connection issues in your area.

– For more troubleshooting help, visit www.joip.com or contact the A service provider.

L

Unplug the base unit’s AC adaptor to reset the unit, then reconnect the AC adaptor. If the 4 indicator is still flashing rapidly, there may be a problem with the base unit hardware. Contact Panasonic service personnel.

24

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 25 Wednesday, August 1, 2007 11:59 AM

Status

Colour

OFF

Preparation

Meaning

Light pattern

L

The power on the base unit is off.

L

To use the A IP line, you need to agree to the

Terms of Use for the A services using the

handset (page 19).

L

The Ethernet cable is not connected properly.

Connect it.

L

Your network devices (hub, router, etc.) are turned off. Check the LEDs for the link status of the devices.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

25

GT15xxE.book Page 26 Wednesday, August 1, 2007 11:59 AM

Preparation

Displays

Base unit display items

Available model:

BB-GT1520/BB-GT1522/BB-GT1540

Displayed item

Meaning

E

Example:

H 1

H m

Base unit ringer for

landline is off (page

59).

Base unit ringer for IP

line is off (page 59).

Greeting or voice memo recording error

(page 61, 63)

Handset number: displayed when paging, or being paged (example shown here: handset

1).

Paging all handsets

(page 71)

Landline is selected for the answering system or ringer

setting (page 59, 60).

When flashing: the answering system is answering a landline call or playing a message on the

landline (page 61).

Displayed item

n

P

Meaning

IP line is selected for the answering system

or ringer setting (page

59, 60).

When flashing: the answering system is answering an internet call or playing a message on the IP

line (page 61).

Base unit is in programming mode

(page 43). (BB-

GT1540)

Handset display items

Meaning Displayed item

E w

_

1

S

Alarm is on (page 55).

Within range of the base unit

Handset has no link to base unit (out of range of base unit, handset is not registered to base unit, or no power on base unit).

Battery level

Landline is in use.

*1

When flashing:

– a landline call is on hold.

– the answering system is answering a landline call.

*2

When flashing rapidly: a landline call is being received.

26

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 27 Wednesday, August 1, 2007 11:59 AM

Displayed item

i s z

Meaning

Example: m

3

IP line is used.

When flashing:

– an internet call is on hold.

– the answering system is answering an internet call.

*2

When flashing rapidly: an internet call is being received.

Speaker is on.

Call privacy mode is

on (page 34).

The handset’s extension number

(example shown here: handset 1)

Handset ringer for

landline is off (page

52).

Handset ringer for IP

line is off (page 52).

Handset ringers for landline and IP line

are off (page 52).

A text message is

protected (page 74).

Night mode is on.

(page 58)

Dial lock is on. (page

58)

*1 k When another phone uses the same landline, S is displayed.

*2 BB-GT1520/BB-GT1522/

BB-GT1540

Preparation

Soft key icons

Soft key icon

U

Action

]

K

1

\

M n

£

}

{

~ s

/

O

W

Returns to the previous screen.

Allows you to make a call. Answers an intercom call.

Displays the menu.

Mutes your voice.

Opens the caller list.

Accepts the current selection.

Opens the handset phonebook.

Displays the phonebook search menu.

Sends the handset phonebook item(s) to selected handset to copy.

Edits the handset phonebook item.

Adds the handset phonebook item.

Switches between

AM, PM, and 24-hour time entry.

Changes the character entry mode.

Stops playback.

(BB-GT1520/

BB-GT1522/

BB-GT1540)

Erases the selected item. Cancels the base unit software update.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

27

GT15xxE.book Page 28 Wednesday, August 1, 2007 11:59 AM

Preparation

Soft key icon

g

^ d w

|

2

0

[

Action

Saves the handset phonebook item.

Erases the character or number.

Goes to the next screen.

Establishes a conference call.

Protects a joip text message.

Turns off the handset ringer.

Plays the message(s).

Registers the handset to the base unit.

Handset menu icons

When in standby mode, pressing down on the centre of the joystick (K) reveals the handset’s main menu. From here you can access various features and settings.

Menu icon

Menu/feature joip

(For A services)

Answer System

(BB-GT1520/

BB-GT1522/

BB-GT1540)

Phonebook

(BB-GT1500)

Ringer settings

Set Date & Time

Initial settings

Customer support

28

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 29 Wednesday, August 1, 2007 11:59 AM

Preparation

right, left, up, or down to move the cursor, then make the correction.

Setting the unit before use

Important:

L

To program features by scrolling

through the display menus, see page

47.

L

Mainly the direct command method is used in these operating instructions.

Display language N

The default setting is “English”.

1

{i}

i K i {#}{1}{1}{0}

2

{V}

/{^}: Select the desired setting.

3

M

i {i}

Date and time N

Set the correct date and time so that:

– You can use the alarm function (page

55).

– The unit will announce the day and time a message was recorded when you play back on the answering

system (page 61). (BB-GT1520/

BB-GT1522/BB-GT1540)

1

K

i {#}{1}{0}{1}

2

Enter the current date, month, and year by selecting 2 digits for each.

Example: 15 August, 2007

{

1}{5} {0}{8} {0}{7}

3

Enter the current hour and minute by selecting 2 digits for each.

Example: 9:30 PM

{

0}{9} {3}{0} i Press s until

“09:30 PM” is displayed.

4

M

i {i}

Note:

L

If you make a mistake when entering the date and time, push the joystick

IP/TEL line selection

The line selection mode determines the line selected when you press {s} to make a call.

“IP”: IP line is selected.

“TEL” (default): Landline is selected.

If you dial a A number (page 4)

then press {s} using the handset, the

IP line is automatically selected.

Note:

L

You can select a line manually regardless of the line selection mode by pressing {TEL} or {IP}.

Handset line selection N

1

K

i {#}{2}{5}{0}

2

{V}

/{^}: Select the desired setting.

3

M

i {i}

Note:

L

When you press ] to make a call

(page 32), the set line is selected.

When you call back from the redial list or caller list, the line indicated by V

(landline) or j (IP line) is selected

(page 32, 45, 62).

Base unit line selection N

Available model:

BB-GT1540

1

K

i {#}{*}{2}{5}{0}

2

{V}

/{^}: Select the desired setting.

3

M

i {i}

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

29

GT15xxE.book Page 30 Wednesday, August 1, 2007 11:59 AM

Preparation

Configuring the Internet connection settings

If your local network uses a DHCP

(Dynamic Host Configuration Protocol) server for automatic IP address assignments, you do not need to change any settings. If your local network uses a static IP address, turn the DHCP connection mode off.

Leaving the DHCP connection mode on allows the base unit to receive an IP address automatically from a DHCP server on your local network.

Automatic setup (default) N

The base unit automatically obtains an

IP address and other Internet connection settings (subnet mask, default gateway, and DNS server addresses).

Turning the DHCP connection mode on:

1

K

i {#}{5}{0}{0}

2

{V}

/{^}: “On”

3

M

i {i}

L

Wait until the 4 indicator on the base unit turns green. When the

4

indicator lights in green, the setting is complete. Confirm your

A number (page 31).

L

When the 4 indicator on the base unit does not light in green even if you wait for a few minutes,

see page 24.

Note:

L

To view the Internet connection settings:

K

i {#}{5}{0}{1} i When finished, press {i}.

Static setup N

If your local network does not use a

DHCP server for automatic IP address assignments, turn the DHCP connection mode off first. Then set the static IP address and other Internet connection settings corresponding to your local network.

Turning the DHCP connection mode off:

1

K

i {#}{5}{0}{0}

2

{V}

/{^}: “Off”

3

M

i {i}

Setting the static IP address and other settings:

1

K

i {#}{5}{0}{1}

2

Set the IP address and other settings.

L

Push the joystick down {V} or up

{^}

to move between the following 5 items.

IP address

Subnet mask

Default gateway

Enter the IP address in this data field.

*1

L

Set 4 numbers (0-

255) separated by periods such as

“192.168.0.253”.

Enter the subnet mask

in this data field.

*1

L

Set 4 numbers (0-

255) separated by periods such as

“255.255.255.0”.

Enter the default gateway address in this data field.

*1

L

Set 4 numbers (0-

255) separated by periods such as

“192.168.0.1”.

30

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 31 Wednesday, August 1, 2007 11:59 AM

DNS1

(DNS server 1)

DNS2

(DNS server 2)

Enter the DNS

(Domain Name

System) server addresses, in each

data field.

*1

L

Set 4 numbers (0-

255) separated by periods such as

“172.23.0.100”.

L

To move the cursor, push the joystick right {>} or left {<}. To correct digits, press ^.

*1 There are some restrictions on these entries. For example, “0.0.0.0” and

“255.255.255.255” are not available.

3

M

i {i}

L

Wait until the 4 indicator on the base unit turns green. When the

4

indicator lights in green, the setting is complete. Confirm your

A number (page 31).

L

When the 4 indicator on the base unit does not light in green even if you wait for a few minutes,

see page 24.

Confirming your A numbers N

After the installation is complete (page

18, 30), the unit is registered to the

service and you receive your A number. The A number is displayed on handset 1 (supplied with the base unit). Once you start operations with the handset, it disappears from the display.

You can also view your A number using any handset as follows.

1

K

i {#}{1}{0}{3}

L

The A number is displayed.

L

To view additional phone number(s) for the IP line, push the joystick down {V} or up {^}.

*1

2

{i}

Preparation

*1 To receive calls via the IP line from landline phones or mobile phones, you need to specially subscribe for additional phone number(s) from A

at www.joip.com (page 4).

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

31

GT15xxE.book Page 32 Wednesday, August 1, 2007 11:59 AM

Making/Answering Calls (Handset)

Making calls

Important:

L

You can choose the landline or IP line to make a call. Make sure to choose the appropriate line for the phone number.

L

To call a Panasonic GLOBARANGE phone, dial the A number consisting of a # followed by 10 digits

(page 4).

Using the speakerphone

1

Dial the phone number, and press

{s}

.

L

The line set for line selection mode is automatically selected

(page 29). When a A number

is dialled (page 3), the IP line is

selected.

L

Speak alternately with the other party.

2

When you finish talking, press {i}.

Note:

L

Use the speakerphone in a quiet environment.

L

To switch to the receiver, press {s}.

Using the handset N

1

Dial the phone number.

L

To correct a digit, press ^.

2

To make a landline call, press

{

TEL}.

To make a A internet call, press

{

IP}.

3

When you finish talking, press {i} or place the handset on the base unit or charger.

Note:

L l

To make calls from your A number to landline and mobile phone numbers via your IP line, you need to subscribe to the appropriate service at www.joip.com

When calling, you may not hear ringtones from your receiver/speaker for more than 1 minute as the unit tries to access the destination phone number. This is normal, please wait.

L

You can also make a call by pressing

]

in step 2. The line set for line

selection mode is automatically

selected (page 29). When a A

number is dialled (page 3), the IP line

is selected.

L l

If it takes some time to call the

number in step 2, press {#} to call it

immediately.

32

Adjusting the receiver/speaker volume

Push the joystick up or down while talking.

Making a call using the redial list

The last 10 phone numbers dialled are stored in the redial list (each 48 digits max.). V (landline) and j (IP line) indicate which line you made the call on.

1

{R}

2

{V}

/{^}: Select the desired phone number.

3

Press ] or {s}.

L

The indicated line is selected.

L

You can also select the line by pressing {TEL} or {IP}.

L k

If {s} is pressed and the other party’s line is engaged, the unit will automatically redial multiple times. The ringer indicator flashes. To cancel, press {i}.

Note:

L

The caller’s name is not stored in the redial list when calling back a number from the caller list.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 33 Wednesday, August 1, 2007 11:59 AM

Erasing a number in the redial list

1

{R}

2

{V}

/{^}: Select the desired phone number.

3

W

i {V}/{^}: “Yes” i M i

{i}

Pause button

A pause is sometimes required when making calls, for example using a PBX or long distance service. When storing a calling card access number and/or PIN in the phonebook, a pause is also

needed (page 42).

For example, if you need to dial the line access number “0” when making outside calls with a PBX:

1

{

0} i {R} i Dial the phone number.

2

{

TEL}

Note:

L

A 3 second pause is inserted each time {R} is pressed. Press repeatedly to insert longer pauses.

Making/Answering Calls (Handset)

To answer the A internet call, press ], {IP}, or {s}.

L

You can also answer the call by pressing any dial key from {0} to

{

9}, {*}, or {#}. (Any key talk

feature)

2

When you finish talking, press {i}.

Note:

L

You can change the ringer indicator

colour and the ringtone (page 52, 54).

You can also adjust the handset ringer

volume (page 52).

Auto talk

This feature allows you to answer a call by simply lifting the handset off the base unit or charger. You do not need to press

]

, {TEL}, or {IP}. To activate this

feature, see page 51.

Temporary ringer off

While the handset is ringing for an outside call, you can turn the ringer off temporarily by pressing 2 or {i}.

Handset LCD backlight

The handset’s LCD backlight colour changes as follows.

Colour

Green

Amber

Meaning

Landline is used.

IP line is used.

Answering calls

Using the handset N

When a call is being received, the ringer indicator on the handset flashes rapidly.

1

To answer the landline call, press

]

, {TEL}, or {s}.

Useful features during a call

Hold button N

This feature allows you to put an outside call on hold.

Press {a} 2 times during an outside call.

L

To release hold, press {TEL} or {IP}.

L

A user of another unit can take the call by pressing {TEL} or {IP}.

Note:

L

If a call is kept on hold for more than 9 minutes, an alarm tone starts to sound and the ringer indicator flashes

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

33

GT15xxE.book Page 34 Wednesday, August 1, 2007 11:59 AM

Making/Answering Calls (Handset)

rapidly. After 1 additional minute on hold, the call is disconnected.

L k

If another phone is connected to

the same line (page 20), you can also

take the call by lifting its handset.

You can combine the calls to make a conference call by pressing {6} again after the 2nd call is connected.

L

To hang up the 2nd call and talk with the 1st caller, press {6}.

L

To hang up both lines, press {i}.

Mute button N

While mute is turned on, you can hear the other party, but the other party cannot hear you.

To mute your voice, press 1.

L

To return to the conversation, press

1

.

Note:

L

When this feature is turned on, 1 flashes.

{

6}

button N k

Pressing {6} allows you to use special features of your host PBX such as transferring an extension call, or accessing optional telephone services.

Note:

L

To change the recall time, see page

57.

For Call Waiting service users

N

Call Waiting service is provided by your landline service provider and A.

This feature allows you to receive calls while you are already talking on the phone. If you receive a call while on the phone, you will hear a Call Waiting tone.

Press {6} to answer the 2nd call.

L

To switch between calls, press {6}.

Note:

L k

Please contact your landline service provider for details.

L l

Please visit www.joip.com or contact the A service provider for details.

l

Pressing {6} allows you to use optional services from A. Visit www.joip.com or contact the A service provider for details.

Making another call on the IP line:

While you are talking with an outside caller, you can make a 2nd call on the same line by pressing {6} then dialling.

L

The 1st call is put on hold.

L

To hang up the 2nd call, press {i}.

The alarm tone starts to sound. Press

{

IP} to talk with the 1st caller again. If you do not press {IP}, the alarm tone sounds for 1 minute and the 1st call is disconnected.

Call share N

This feature allows you to join an existing outside call.

When another unit is on an outside call, press {TEL} or {IP} to select the line that is being used for the call.

Note:

L

Multiple parties can join a conference call. The possible number of participating parties depends on the current system usage. When another participating party cannot join a conversation, the busy tone sounds and the handset displays “Busy”.

Call privacy N

Call privacy allows you to prevent other users from joining your conversations with outside callers. To allow other users

34

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 35 Wednesday, August 1, 2007 11:59 AM to join your conversations, leave this feature off.

1

Press K during an outside call.

2

Press {2} to select “Privacy on” or “Privacy off”.

L

When this feature is turned on,

“z” is displayed.

Note:

L

This feature will turn off after you hang up the call.

Making/Answering Calls (Handset)

Note:

L

If you subscribe to the Caller ID service, the 2nd caller’s information is displayed as the call is being received

(page 44).

L

To turn the interrupt tone off, see page

51.

Using the other line,

conference call N

When a call is being received on the other line during a conversation, the interrupt tones sound.

You can answer the 2nd call while holding the 1st call. You can also combine the landline call and internet call to make a conference call.

Example: If you are using the landline

1

Press {a} 2 times to put the 1st call (landline) on hold.

2

Press {IP} to make or answer a 2nd call.

L

To hold the 2nd call, press {a} 2 times.

3

To hang up the 2nd call and return to the 1st call (landline):

Press {TEL}.

To make a conference call:

Press w.

L

To hang up only one line, press

{

TEL} or {IP} for the party with which you want to continue talking.

L

To put both lines on hold, press

{a}

. To talk with only one caller, press {TEL} or {IP} for the party with which you want to continue talking. To resume both lines, press w.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

35

GT15xxE.book Page 36 Wednesday, August 1, 2007 11:59 AM

Making/Answering Calls (Base Unit)

Making calls

Important:

L

You can choose the landline or IP line to make a call. Make sure to choose the appropriate line for the phone number.

L

To call a Panasonic GLOBARANGE phone, dial the A number consisting of a # followed by 10 digits

(page 4).

access the destination phone number.

This is normal, please wait.

L l

If it takes some time to call the

number in step 2, press {#} to call it

immediately.

L

While on a call, you can switch from the base unit to the handset:

– Press {TEL} or {IP} on the handset, then press {s} on the base unit.

– If the handset is on the base unit, simply lift it.

Adjusting the speaker volume

Press {>} or {<} repeatedly while talking.

Using the base unit f

Available model:

BB-GT1540

1

To make a landline call, press

{

TEL}.

To make a A internet call, press

{

IP}.

L

You can also make a call by pressing {s}. The line set for line selection mode is automatically

selected (page 29).

2

Dial the phone number.

3

When the other party answers, speak into the MIC.

L

Speak alternately with the other party.

4

When you finish talking, press {s}.

Note:

L

Use the speakerphone in a quiet environment.

L l

To make calls from your A number to landline and mobile phone numbers via your IP line, you need to subscribe to the appropriate service at www.joip.com

When calling, you may not hear ringtones from your speaker for more than 1 minute as the unit tries to

Redialling the last number dialled

Press {TEL} or {IP}. i {R}

L k

If the other party’s line is engaged, the unit will automatically redial multiple times. The speakerphone indicator flashes. To cancel, press { ■}.

Answering calls

Using the base unit f

Available model:

BB-GT1540

When a call is being received, the TEL indicator or IP indicator flashes rapidly.

1

{s}

L

You can also answer the call by pressing the flashing {TEL} or

{

IP}.

2

Speak into the MIC.

3

When you finish talking, press {s}.

36

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 37 Wednesday, August 1, 2007 11:59 AM

Useful features during a call

Making/Answering Calls (Base Unit)

Note:

L

To change the recall time, see page

57.

Available model:

BB-GT1540

Hold button f

This feature allows you to put an outside call on hold.

Press {a} during an outside call.

L

To release hold, press the flashing

{

TEL} or {IP}.

L

A handset user can take the call by pressing {TEL} or {IP}.

Note:

L

While an outside call is on hold, the

TEL indicator or IP indicator on the base unit flashes.

L

If a call is kept on hold for more than 9 minutes, an alarm tone starts to sound. After 1 additional minute on hold, the call is disconnected.

L k

If another phone is connected to

the same line (page 20), you can also

take the call by lifting its handset.

l

Pressing {6} allows you to use optional services from A. Visit www.joip.com or contact the A service provider for details.

Making another call on the IP line:

While you are talking with an outside caller, you can make a 2nd call on the same line by pressing {6} then dialling.

L

The 1st call is put on hold.

L

To hang up the 2nd call, press {s}.

The alarm tone starts to sound. Press

{

IP} to talk with the 1st caller again. If you do not press {IP}, the alarm tone sounds for 1 minute and the 1st call is disconnected.

You can combine the calls to make a conference call by pressing {6} again after the 2nd call is connected.

L

To hang up the 2nd call and talk with the 1st caller, press {6}.

L

To hang up both lines, press {s}.

Mute button f

While mute is turned on, you can hear the other party, but the other party cannot hear you.

To mute your voice, press {T}.

L

To return to the conversation, press

{T}

or {s}.

{ 6}

button f k

Pressing {6} allows you to use special features of your host PBX such as transferring an extension call, or accessing optional telephone services.

For Call Waiting service users

f

Call Waiting service is provided by your landline service provider and A.

This feature allows you to receive calls while you are already talking on the phone. If you receive a call while on the phone, you will hear a Call Waiting tone.

Press {6} to answer the 2nd call.

L

To switch between calls, press {6}.

Note:

L k

Please contact your landline service provider for details.

L l

Please visit www.joip.com or contact the A service provider for details.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

37

GT15xxE.book Page 38 Wednesday, August 1, 2007 11:59 AM

Making/Answering Calls (Base Unit)

Call share f

This feature allows you to join an existing outside call.

When a handset is on an outside call, press {TEL} or {IP} to select the line that is being used for the call.

Note:

L

Multiple parties can join a conference call. The possible number of participating parties depends on the current system usage. When another participating party cannot join a conversation, the busy tone sounds.

talking. To resume both lines, press {5}.

Note:

L

To turn the interrupt tone off, see page

51.

Using the other line,

conference call f

When a call is being received on the other line during a conversation, the interrupt tones sound.

You can answer the 2nd call while holding the 1st call. You can also combine the landline call and internet call to make a conference call.

Example: If you are using the landline

1

Press {a} to put the 1st call

(landline) on hold.

2

Press {IP} to make or answer a 2nd call.

L

To hold the 2nd call, press {a}.

3

To hang up the 2nd call and return to the 1st call (landline):

Press {TEL}.

To make a conference call:

Press {5}.

L

To hang up only one line, press

{

TEL} or {IP} for the party with which you want to continue talking.

L

To put both lines on hold, press

{a}

. To talk with only one caller, press {TEL} or {IP} for the party with which you want to continue

38

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 39 Wednesday, August 1, 2007 11:59 AM

Making internet calls using your mobile phone

Making Internet Calls (Mobile Phone)

Note:

L

The handset or base unit cannot join the call.

Available model:

BB-GT1520/BB-GT1522/BB-GT1540

Turning this feature on or off f

The default setting is ON. If you do not want to use this feature, you can turn it off using the base unit.

First press and hold { ■}, then press and hold {IP/TEL}. Keep holding down both buttons until the base unit beeps.

L

When turned on, one beep sounds.

L

When turned off, 2 beeps sound.

l

Important:

L

To use this feature, you need an additional phone number for the IP

line other than the joip number (page

4). If you do not have one, subscribe

at www.joip.com

You can make internet calls with your mobile phone via the base unit. First, call your unit’s answering system by dialling the additional phone number you subscribed at www.joip.com

Next, dial the phone number you want to call. You can make cheaper international calls, even while you are out.

Perform the following beforehand:

– Set your own remote code of the answering system to turn the remote

operation on (page 64).

– Turn on the answering system for the

IP line (page 60, 65).

1

Dial the phone number you subscribed at www.joip.com

2

After the greeting message starts, enter your remote code of the

answering system (page 64).

3

{#}{

9}

4

After the dial tone sounds, dial the phone number you want to call. i

{#}

L

The phone number is dialled via the IP line.

5

When you finish talking, hang up.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

39

GT15xxE.book Page 40 Wednesday, August 1, 2007 11:59 AM

Handset Phonebook

Handset phonebook

You can add up to 100 items to the handset phonebook and search for phonebook items by name.

Important:

L

Caller ID subscribers can use ringer

ID and light-up ID features (page 45).

L

You can add and edit phonebook items by accessing your account on the A website (www.joip.com), then downloading your web phonebook to the base unit. To import them to your

handset, see page 73.

Adding items to the handset phonebook

1

n

2

~

3

Enter the name (max. 16 characters;

page 79). i M

4

Enter the phone number (max. 32 digits). i M

L

If you do not need to assign the ringer ID and light-up ID, go to

step 9.

5

{V}

/{^}: “Set Ringer ID” i

M

6

{V}

/{^}: Select the desired ringer ID

(page 45). i M

L

When selecting “No Ringer

ID”, the ringtone set for the IP line

rings (page 54).

7

{V}

/{^}: “Set Light-up ID” i

M

8

{V}

/{^}: Select the desired light-up

ID (page 45). i M

9

g

L

To add other items, repeat from

step 3.

10

{i}

40

Note:

L

In step 2, you can also press K i

{V}

/{^}: “New Entry” i M instead of pressing ~.

L

If you select “No Ringer ID”

(default) in step 6, the handset uses

the ringtone you selected on page 54

when a call is received from that caller.

L

If you select “No Light-upID”

(default) in step 8, the handset uses

the ringer indicator colour you

selected on page 52 when a call is

received from that caller.

To store emergency numbers

Emergency numbers are numbers stored in the phonebook that can be dialled using the phonebook even when

dial lock is turned on (page 58). To store

a number as an emergency number, add

# at the beginning of the name (see

“Adding items to the handset phonebook”, page 40).

Finding and calling a handset phonebook item

Important:

L

Make sure to choose the appropriate line for the phone number to call back.

Searching for a name alphabetically by scrolling through all items

1

n

2

{V}

/{^}: Select the desired item.

3

To make a landline call, press

{

TEL}.

To make a joip internet call, press

{

IP}.

Searching for a name by initial

1

n

i £

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 41 Wednesday, August 1, 2007 11:59 AM

Handset Phonebook

2

{V}

/{^}: Select the character entry mode that contains the character

you are searching for (page 79). i

M

3

Press the dial key ({0} – {9}, or

{#}

) that corresponds to the first

letter you are searching for (page

79).

L

If there is no item corresponding to the letter you selected, the next item is displayed.

4

{V}

/{^}: Select the desired item.

5

To make a landline call, press

{

TEL}.

To make a A internet call, press

{

IP}.

To change the light-up

ID

4

g

i {i}

Select the current light-up ID. i M i

{V}/{^}: Select the desired light-up

ID.

*1

i M

*1 To turn the lightup ID off, select

“No Light-

upID”.

Erasing items in the handset phonebook

Editing items in the handset phonebook

1

n

2

Find the desired item (page 40). i

3

{

{V}

/{^}: Select the information you want to change.

To change the name or phone number

To change the ringer ID

Select the name or phone number. i

M

i Edit the

information (page

79). i M

Select the current ringer ID. i M i

{V}/{^}: Select the desired item.

*1

i

M

*1 To turn the ringer

ID off, select “No

Ringer ID”.

Erasing an item

1

n

2

3

4

Find the desired item (page 40).

K

{V}

i {V}/{^}: “Erase” i M

/{^}: “Yes” i M i {i}

Erasing all items

1

n

i K

2

{V}

/{^}: “Erase All” i M

3

{V}

/{^}: “Yes” i M

4

{V}

/{^}: “Yes” i M

L

When all items have been erased, “Erased” is displayed.

5

{i}

Chain dial

This feature allows you to dial phone numbers in the handset phonebook while you are on a call. This feature can be used, for example, to dial a calling card access number or bank account

PIN that you have stored in the handset phonebook, without having to dial manually.

1

During an outside call, press n.

2

Find the desired item (page 40). i

]

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

41

GT15xxE.book Page 42 Wednesday, August 1, 2007 11:59 AM

Handset Phonebook

Note:

L

When storing a calling card access number and your PIN in the phonebook as one phonebook item, press {R} to add pauses after the

number and PIN as necessary (page

33).

Copying handset phonebook items

You can copy one or all of the phonebook items from one handset to another.

Important:

L

Ringer ID and light-up ID for phonebook items are not copied.

Copying an item

1

n

2

Find the desired item (page 40). i

K

3

{V}

/{^}: “Copy” i M

4

{V}

/{^}: Select the handset to copy to. i }

L

When the item has been copied,

“Completed” is displayed.

L

To continue copying another item:

{V}

/{^}: “Yes” i M i Find

the desired item (page 40). i

}

5

{i}

Copying all items

1

n

i K

2

{V}

/{^}: “Copy All” i M

3

{V}

/{^}: Select the handset to copy to. i }

L

When all items have been copied,

“Completed” is displayed.

4

{i}

42

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 43 Wednesday, August 1, 2007 11:59 AM

Base unit speed dialler

Available model:

BB-GT1540

You can assign one phone number to each of the 10 dial keys ({0} – {9}) on the base unit.

Adding phone numbers to the speed dialler

Important:

L

Before adding phone numbers, make sure the base unit is not being used.

1

{l}

2

Enter the phone number (max. 32 digits).

L

If a pause is required for dialling, press {R} where needed.

L

If you misdial, press { ■} and

repeat from step 1.

3

{l}

4

Press a dial key ({0} – {9}).

Note:

L

If a phone number is assigned to a dial key which already contains a phone number, the old number will be erased.

L

We recommend you make a note of which phone numbers are stored in which dial keys.

L

When {*} is pressed, “$” is displayed.

When {#} is pressed, “#” is displayed.

When {6} is pressed, “F” is displayed.

Base Unit Speed Dialler

dial the line access number “0”

(example) when making landline calls with a PBX:

In step 2, press {0}, {R}, then enter the

phone number.

Note:

L

A 3 second pause is inserted each time {R} is pressed. Press repeatedly to insert longer pauses.

“P” is displayed when {R} is pressed.

To erase a stored phone number

1

Press {l} 2 times.

2

Press the desired dial key ({0} –

{

9}).

Calling someone with the speed dialler

Important:

L

Make sure to choose the appropriate line for the phone number.

1

To make a landline call, press

{

TEL}.

To make a A internet call, press

{

IP}.

2

{l}

3

Press the desired dial key ({0} –

{

9}).

Note:

L

Speed dial numbers assigned to the base unit dial keys can only be dialled from the base unit.

PAUSE button

A pause is sometimes required when making calls, for example using a PBX or long distance service. If you need to

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

43

GT15xxE.book Page 44 Wednesday, August 1, 2007 11:59 AM

Caller ID Service

Using Caller ID service

This unit is Caller ID compatible. To use

Caller ID features, you must subscribe to

Caller ID services offered by your landline service provider and the A service provider.

Note:

L k

Please contact your landline service provider for details.

L l

Please visit www.joip.com or contact the A service provider for details.

Caller ID features N k

When an outside call is being received, the calling party’s phone number is displayed.

L

Generally caller information is displayed from the 2nd ring.

l

When a call is received from a

Panasonic GLOBARANGE phone, the calling party’s A number is displayed.

If the caller sets to show the name at www.joip.com, it is displayed.

Caller information for the last 50 callers is logged in the caller list from the most recent call to the oldest.

L

If the unit cannot receive caller information, the following is displayed:

“Private Caller”: The caller requested not to send caller information.

– k “Out of Area”: The caller dialled from an area which does not provide Caller ID service.

L k

If the unit is connected to a PBX system, caller information may not be received properly. Consult your PBX supplier.

Missed calls N

If a call is not answered, the unit treats the call as a missed call. “Missed

call” is displayed on the handset. This lets you know if you should view the caller list to see who called while you were out. You can view the number of missed calls by pressing \.

Note:

L

If you press \, then press {i} without viewing all missed calls in the caller list, “Missed call” disappears from the display. When you receive another new call, it is displayed again.

Custom name display N

When the Caller ID number is received and it matches a phone number stored in the phonebook, the stored name from the phonebook is displayed and logged in the caller list.

Call Waiting Caller ID display N

The 2nd caller’s information is displayed

after you hear a call waiting tone (page

34). Press {6} to answer the 2nd call.

L

To switch between calls, press {6}.

Note:

L k

You must subscribe to both

Caller ID and Call Waiting with Caller

ID services. Please contact your landline service provider for details and availability of this service in your area.

L l

Please visit www.joip.com or contact the A service provider to subscribe.

44

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 45 Wednesday, August 1, 2007 11:59 AM

Ringer ID/Light-up ID N

These features can help you identify who is calling by using different ringers and ringer indicator colours for different callers stored in the phonebook. You can assign a different ringer and indicator colour to each phonebook item. When a call is received from a caller stored in the phonebook, the assigned ringer rings and the assigned ringer indicator colour flashes after Caller ID information is displayed.

If you select “No Ringer ID” (default) or “No Light-upID” (default), the handset uses the ringtone or ringer

indicator colour you selected (page 52,

54) when a call is received from that

caller.

Caller list

Important:

L

Only 1 person can access the caller list at a time.

Viewing the caller list and

calling back N

1

\

2

Push the joystick down to search from the most recent call, or push the joystick up to search from the oldest call.

3

To call back, select the indicated line by pressing {TEL} or {IP}.

To exit, press {i}.

Note:

L V

(landline) and j (IP line) indicate which line the caller information was received from.

Caller ID Service

L

A Q is displayed for caller information which has already been viewed or answered by any handset.

L

If an arrow (>) is displayed after the number, the whole phone number is not shown. Push the joystick right to see the remaining information. To return to the previous display, push the joystick left.

Editing a caller’s phone

number before calling back N

You can edit a phone number in the caller list.

1

\

2

{V}

/{^}: Select the desired item. i

{

3

Add or erase digits to the beginning of the number as necessary.

L

To add a digit, press the desired dial key.

L

To erase a digit, press ^.

4

Press ].

Note:

L

{

is not displayed for A numbers. They are not necessary to be edited.

L

The edited phone number is not saved in the caller list.

Storing caller information into

the handset phonebook N

1

\

2

{V}

/{^}: Select the desired item. i

K

3

{V}

/{^}: “Add Phonebook” i

M

L

To change the information,

perform step 3, “Editing items in the handset phonebook”, page

41.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

45

GT15xxE.book Page 46 Wednesday, August 1, 2007 11:59 AM

Caller ID Service

4

g

i {i}

Erasing caller information N

Erasing a selected item

1

\

2

{V}

/{^}: Select the desired item.

3

W

i {V}/{^}: “Yes” i M i

{i}

Erasing all items

1

\

2

W

i {V}/{^}: “Yes” i M

46

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 47 Wednesday, August 1, 2007 11:59 AM

Programming

Programmable settings

Handset

You can customise the unit by programming the following features.

To access the features, there are 2 methods:

– scrolling through the display menus (page 47)

– using the direct commands (page 51)

Base unit

To change the base unit ringer volume and tone, see page 59. (BB-GT1520/

BB-GT1522/BB-GT1540)

Programming by scrolling through the display menus N

1

K

2

Push the joystick up {^}, down {V}, left {<}, or right {>} to select the desired menu. i M

L

If there are sub-menu(s), push the joystick down {V} or up {^} to select the desired item. i M

3

Push the joystick down {V} or up {^} to select the desired setting. i M

L

This step may vary depending on the feature being programmed.

4

{i}

BB-GT1500

Main menu joip

Phonebook

Sub-menu 1 joip service joip message

My joip numbers joip settings

Sub-menu 2

DHCP

*1

IP settings

*1

joip MSG alert

Page

75

74

31

30

30

75

40

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

47

GT15xxE.book Page 48 Wednesday, August 1, 2007 11:59 AM

Programming

Main menu

Ringer settings

(

Initial settings

Customer support

Sub-menu 1

Ringer Volume

Ext. Ringtone

(External ringtone)

Import ringtone

Interrupt tone

Ring colour

Night Mode

Set Date & Time Set Date & Time

Alarm

Time Adjustment

*1

Dial lock

*1

Auto Intercom

Contrast

Keytones

Auto Talk

New Msg. Alert

IP/TEL select

Base Unit Setup

Set phone line

Registration

*1

Handset Name

Calling Code

Select Language

Web site

Software version

*1

Sub-menu 2

Start/End

On/Off

Ring Delay

Base Unit PIN

*1

Set recall time

*1

Register Handset

Deregistration

Page

54

33

68

29

57

69

58

59

29

55

73

58

56

55

29

52

57

56

57

77

77

*1 If you program these settings using one of the handsets, you do not need to program the same item using another handset.

48

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 49 Wednesday, August 1, 2007 11:59 AM

Programming

BB-GT1520/BB-GT1522/BB-GT1540

Main menu joip

Answer System

Ringer settings

(

Set Date &

Time

Sub-menu 1 joip service joip message

My joip numbers joip settings

Play New Msg.

Play All Msg.

To erase all

*1

Settings

Ringer Volume

Ext. Ringtone

(External ringtone)

Import ringtone

Interrupt tone

Ring colour

Night Mode

Set Date & Time

*1

Alarm

Time Adjustment

*1

Sub-menu 2

DHCP

*1

IP settings

*1

joip MSG alert

Number of Rings

*1

Recording Time

*1

Remote Code

*1

Call Screening

*1

66

64

67

54

62

62

63

66

Page

75

74

31

30

30

75

Start/End

On/Off

Ring Delay

58

58

59

29

73

55

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

49

GT15xxE.book Page 50 Wednesday, August 1, 2007 11:59 AM

Programming

Main menu

Initial settings

Customer support

Sub-menu 1

Dial lock

*1

Auto Intercom

Contrast

Keytones

Auto Talk

New Msg. Alert

IP/TEL select

Base Unit Setup

Set phone line

Registration

Handset Name

Calling Code

Select Language

Web site

Software version

*1

Sub-menu 2

Interrupt tone

*1

Night Mode

*1*3

IP/TEL select

*1*2

Base Unit PIN

*1

Set recall time

*1

Register Handset

Deregistration

Page

57

69

33

66, 68

29

58

29

56

57

77

77

56

55

29

52

57

*1 If you program these settings using one of the handsets, you do not need to program the same item using another handset.

*2 BB-GT1540

*3 Night mode has “Start/End”, “On/Off” and “Ring Delay” sub-menus.

50

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 51 Wednesday, August 1, 2007 11:59 AM

Programming

Programming using the direct commands N

1

K

i {#}

2

Enter the desired feature code.

3

Enter the desired setting code. i M

L

This step may vary depending on the feature being programmed.

4

{i}

Note:

L

In the following table, < > indicates the default setting.

L

If you make a mistake or enter the wrong code, press {i}, then start again from

step 1.

Feature

Alarm

Auto Intercom

Feature code

{

7}{2}{0}

{

2}{7}{3}

{

2}{0}{0}

{

1}{3}{2}

{

1}{4}{5}

Setting code

{

1}: On (Ringer On)

{

2}: On (Ringer Off)

{

0}: <Off>

{

1}: On {0}: <Off>

{

1}-{6}: Level 1–6 <3>

Page

55

69

33

56

Auto Talk

*1

Base Unit PIN

*2

Contrast

(Display contrast)

Deregistration

Dial lock

*2

Display Language

Ext.

Ringtone

(External ringtone)

(Handset)

IP

TEL

Handset Name

Interrupt tone

*3

(Handset)

Interrupt tone

*2*3

(BB-GT1520/

BB-GT1522/

BB-GT1540 base unit)

IP/TEL select

(Handset)

IP/TEL select

*2

(BB-GT1540 base unit)

{

1}{3}{1}

{

2}{5}{1}

{

1}{1}{0}

{

1}{6}{1}{1}

{

1}{6}{1}{2}

{

1}{0}{4}

{

2}{0}{1}

{*}{

2}{0}{1}

{

2}{5}{0}

{*}{

2}{5}{0}

{

1}-{3}: Ringtone 1-3

{

4}-{6}: Melody 1-3

{

7}: Demo

*6

IP: <Ringtone 2>

TEL: <Ringtone 1>

{

1}: <On>

{

0}: Off

{

1}: IP

{

2}: <TEL>

77

57

29

54

56

29

29

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

51

GT15xxE.book Page 52 Wednesday, August 1, 2007 11:59 AM

Programming

Feature

Keytones

*4

New Msg. Alert

Night

Mode

*5

(Handset)

Start/

End

On/Off

Night

Mode

*2*5

(BB-

GT1520/

BB-

GT1522/

BB-

GT1540 base unit)

Ring

Delay

Start/

End

On/Off

Ring

Delay

Register Handset

Ring colour

(Ringer indicator colour)

Feature code

{

{

{

{

{

{

{

1}{6}{5}

3}{4}{0}

2}{3}{7}

2}{3}{8}

2}{3}{9}

{*}{

2}{3}{7}

{*}{

2}{3}{8}

{*}{

2}{3}{9}

1}{3}{0}

2}{3}{5}

Setting code

{

{

{

1}: <On> {0}: Off

1}: On {0}: <Off>

{

1}: On {0}: <Off>

{

1}: 30 sec.

{

2}: <60 sec.>

{

3}: 90 sec.

{

4}: 120 sec.

{

0}: No Ringing

1}: On {0}: <Off>

{

1}: 30 sec.

{

2}: <60 sec.>

{

3}: 90 sec.

{

4}: 120 sec.

{

0}: No Ringing

{

1}: <Colour1>

{

2}: Colour2

{

3}: Colour3

{

4}: Multicolour

{

1}-{6}: Level 1–6 <6>

{

0}: Off

Page

66, 68

58

58

59

58

58

59

77

Ringer

Volume

(Handset)

IP

TEL

Set Date & Time

*2

Web site

*7

(Customer support)

{

{

{

{

1}{6}{0}{1}

1}{6}{0}{2}

1}{0}{1}

6}{8}{0}

www.globarange.com

29

*1 If you subscribe to Caller ID service and want to view the caller’s information after lifting up the handset to answer a call, turn off this feature.

*2 If you program these settings using one of the handsets, you do not need to program the same item using another handset.

*3 This tone lets you know when you receive a call while you are on the other line, on an intercom call, or monitoring a room. The tone sounds 2 times.

*4 Turn this feature off if you prefer not to hear key tones while you are dialling or pressing any keys, including confirmation tones and error tones.

*5 In order to set the night mode, you must first set the date and time (page 29).

*6 The preset song “Demo” in this product is used with the permission of © 2006

Copyrights Vision Inc.

52

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 53 Wednesday, August 1, 2007 11:59 AM

Programming

*7 The handset can display the Internet address where you can get further information for this product using your computer.

For landline k

Feature

Calling Code

Set recall time

*1

Time Adjustment

*1 *2

(Caller ID subscribers only)

Feature code Setting code

{

2}{5}{9}

{

1}{2}{1}

{

2}{2}{6}

{

1}:

<Caller ID[Auto]>

{

2}: Manual

Page

55

57

*1 If you program these settings using one of the handsets, you do not need to program the same item using another handset.

*2 If the caller ID time and date display service is available in your area, this feature allows the unit to automatically adjust the date and time setting when caller information is received. To use this feature, set the date and time first.

For IP line l

Feature

DHCP

*1

Import ringtone

IP settings

*1

joip message joip MSG alert

(A message alert)

joip service

My joip numbers

Software version

*1

Feature code

{

{

{

{

{

{

{

{

5}{0}{0}

1}{7}{0}

5}{0}{1}

3}{6}{0}

3}{6}{1}

5}{3}{0}

1}{0}{3}

7}{2}{4}

Setting code

{

{

1}: <On> {0}: Off

1}: <On> {0}: Off

75

31

57

*1 If you program these settings using one of the handsets, you do not need to program the same item using another handset.

Page

30

73

30

74

75

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

53

GT15xxE.book Page 54 Wednesday, August 1, 2007 11:59 AM

Programming

For the answering system (BB-GT1520/BB-GT1522/BB-GT1540)

Feature

Call Screening

Number of

Rings

*1

*1

Feature code

{

3}{1}{0}

Setting code

{

1}: <On> {0}: Off

IP

TEL

{

2}{1}{1} i {1}

{

2}-{7}: Rings

{

2}{1}{1} i {2}

<4 Rings>

{

0}: Toll saver

*2

{

3}{2}{4} –

Play All Msg.

(All message playback)

{

3}{2}{3} –

Play New Msg.

(New message playback)

Recording

Time

*1

Remote Code

*1

IP

TEL

{

3}{0}{5} i {1}

{

1}: 1 Minutes

{

3}{0}{5} i {2}

{

2}: 2 Minutes

{

3}: <3 Minutes>

{

3}{0}{6} Default: Off

To erase all

*1

(Erasing all messages)

{

3}{2}{5} –

Page

67

66

62

62

66

64

63

*1 If you program these settings using one of the handsets, you do not need to program the same item using another handset.

*2 l Depending on the condition of your network connection, “Toll saver” may not be used for the IP line.

Adjusting the handset ringtone N

You can change the ringtone heard when an outside call is received for each line. You

can also assign the ringtone you have imported (page 73). The default setting for the

IP line is “Ringtone 2” and for the TEL line is “Ringtone 1”.

1

K

i {#}{1}{6}{1}

2

{V}

/{^}: Select the desired line.

3

{V}

/{^}: Select the desired setting.

4

M

i {i}

54

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 55 Wednesday, August 1, 2007 11:59 AM

Programming

Alarm N

An alarm will sound for 3 minutes at the set time. Set the date and time beforehand

(page 29).

1

K

i {#}{7}{2}{0} i M

2

{V}

/{^}: Select the desired alarm mode. i M

Off

Once

Daily

Turns alarm off. Go to step 5.

The alarm sounds once at the set time. Enter the desired date.

An alarm sounds daily at the set time.

3

Set the desired time. i M

4

{V}

/{^}: Select the desired ringtone. i M

L

We recommend selecting a ringtone different from the ringtone set for incoming calls.

5

{V}

/{^}: “Save” i M i {i}

Note:

L

To stop the alarm, press any dial key or place the handset on the base unit or charger.

L

When the handset is in use, the alarm will not sound until the handset enters standby mode.

L

If you are on a call, beeps will sound and E will flash at the set time. The alarm will not sound until you hang up.

L

If you select “Once”, the setting will change to “Off” after the alarm sounds.

L

The ringer volume for the alarm follows the higher volume level of the 2 lines (page

52).

L

When the ringer volume is set to off for both lines, the handset rings at the low level for alarm.

Calling code for the handset N k

If you need to dial a special calling code to make calls using the telephone services of a certain service provider, you can store the calling code in advance and dial it by simply pressing and holding the {*} while dialling a phone number.

Important:

L

To use this feature, you must store the calling code in advance.

Example:

L

If you store the calling code “098” and press and hold {*} before dialling

“12345”, the unit dials “09812345” automatically.

Assigning the calling code number

1

K

i {#}{2}{5}{9}

2

Enter the desired calling code (24 digits max.). i M i {i}

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

55

GT15xxE.book Page 56 Wednesday, August 1, 2007 11:59 AM

Programming

Making calls using a calling code

When dialling manually:

1

Press and hold {*}.

L

The calling code you stored will be displayed.

2

Dial the phone number manually.

3

{

TEL}

L

You can also make a call by pressing ]. The line set for line selection mode

is automatically selected (page 29).

When dialling from the redial list, phonebook, or caller list:

1

Display the desired phone number in the redial list (page 32), phonebook (page

40), or caller list (page 45).

2

Press and hold {*}.

L

The calling code you stored will be displayed before the phone number.

3

{

TEL}

L

You can also make a call by pressing ]. The line set for line selection mode

is automatically selected (page 29).

Changing the base unit PIN (Personal Identification Number) N

Important:

L

If you change the PIN, please make note of your new PIN. The unit will not reveal

the PIN to you. If you forget your PIN, see page 91.

1

K

i {#}{1}{3}{2}

2

Enter the current 4-digit base unit PIN (default: “0000”).

3

Enter the new 4-digit base unit PIN.

4

M

i {i}

Changing the handset name N

Each handset can be given a customised name (“Bob”, “Kitchen”, etc.). This is useful when you make intercom calls between handsets. You can also select whether or not the handset name is displayed in standby mode. The default setting is “Off”. If you select “On” without entering any handset name, “Handset 1” to “Handset 6” is displayed.

1

K

i {#}{1}{0}{4}

2

Enter the desired name (max. 10 characters; see the character table, page 79).

L

If not required, go to step 3.

3

M

4

{V}

/{^}: Select the desired setting. i M i {i}

56

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 57 Wednesday, August 1, 2007 11:59 AM

Programming

Setting the recall time k N

The recall time depends on your telephone exchange or host PBX. Consult your PBX supplier if necessary. The default setting is “100 millisecond”. The setting should stay at “100 millisecond” unless pressing {6} fails to pick up the call waiting call.

1

K

i {#}{1}{2}{1}

2

{V}

/{^}: Select the desired setting. i M i {i}

Updating the base unit software N

A may offer new features and improve its software version from time to time. If you set the base unit software update setting to manual mode at www.joip.com, you need to download the update when “Update version. Press OK.” is displayed on the handset.

Important:

L

Make sure the 4 indicator is lit in green and the IP indicator is not lit on the base unit.

1

Press M while “Update version. Press OK.” is displayed.

L

The current and new base unit software versions are displayed.

L

If you want to download the update later, press W. When you are ready to

download, see “Confirming the base unit software version”, page 57.

2

M

Note:

L

The IP indicator and 4 indicator on the base unit flash while downloading. When the download is complete, the IP indicator goes out while the 4 indicator stops flashing and changes to steady green.

Confirming the base unit software version

1

K

i {#}{7}{2}{4}

L

The current base unit software version is displayed.

2

If “Update version?” is displayed, press M to download. If not, press W.

Dial lock

This feature prohibits making outside calls. The default setting is “Off”.

Important:

L

When dial lock is turned on, only phone numbers stored in the phonebook as emergency numbers (numbers stored with a # at the beginning of the

name) can be dialled using the phonebook (page 40). We recommend storing

emergency numbers in the phonebook before using this feature.

L

When dial lock is turned on:

– you cannot store, edit, or erase items in the phonebook

– you cannot import those items to the handset (page 73)

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

57

GT15xxE.book Page 58 Wednesday, August 1, 2007 11:59 AM

Programming

To turn dial lock on N

1

K

i {#}{2}{5}{1}

2

Enter a 4-digit password.

L

This password is required when turning dial lock off. We recommend writing the password down.

3

Press M 2 times. i {i}

To turn dial lock off N

1

K

i {#}{2}{5}{1}

2

Enter the same password that was entered when dial lock was turned on.

3

Press M 2 times. i {i}

Note:

L

If you forget the password, see page 91.

Night mode

Night mode allows you to select a block of time during which the handset or base unit will not ring for outside calls. This feature is useful for times when you do not want to be disturbed, for example, while sleeping. Night mode can be set independently for

the handset and the base unit (page 58). Set the date and time beforehand (page

29).

Setting the start and end time for night mode N

The default start time is “23:00”. The default end time is “06:00”.

1

To set for the handset:

K

i {#}{2}{3}{7}

To set for the base unit (BB-GT1520/BB-GT1522/BB-GT1540):

K

i {#}{*}{2}{3}{7}

2

Enter the desired hour and minute you wish to start this feature.

3

Enter the desired hour and minute you wish to end this feature.

4

M

i {i}

Turning night mode on/off N

The default setting is “Off”.

1

To set for the handset:

K

i {#}{2}{3}{8}

To set for the base unit (BB-GT1520/BB-GT1522/BB-GT1540):

K

i {#}{*}{2}{3}{8}

2

{V}

/{^}: Select the desired setting. i M i {i}

58

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 59 Wednesday, August 1, 2007 11:59 AM

Programming

Setting the ring delay for night mode N

This setting allows the handset or base unit to ring during night mode if the caller waits long enough. After the selected amount of time passes, the unit will ring. If you select “No Ringing”, the unit will never ring during night mode. The default setting is “60 sec.”.

1

To set for the handset:

K

i {#}{2}{3}{9}

To set for the base unit (BB-GT1520/BB-GT1522/BB-GT1540):

K

i {#}{*}{2}{3}{9}

2

{V}

/{^}: Select the desired setting. i M i {i}

Note:

L

When the answering system answers the call, this feature does not work.

(BB-GT1520/BB-GT1522/BB-GT1540)

Adjusting the base unit ringer volume (BB-GT1520/

BB-GT1522/BB-GT1540) f

1

Press {IP/TEL} repeatedly until the display shows the desired line (n or m

).

L

You cannot set the ringer volume for both lines at the same time.

2

Press {>} or {<} repeatedly to select the desired volume.

L

To turn the ringer off, press and hold {<} until the unit beeps.

L

To stop ringing, press { ■}.

Setting the base unit ringtone (BB-GT1520/BB-GT1522/

BB-GT1540) f

There are 3 tones and 3 melodies.

1

Press {IP/TEL} repeatedly until the display shows the desired line (n or m

).

L

You cannot set the ringtone for both lines at the same time.

2

{>}

3

Within 10 seconds, press {<} or {>} repeatedly to select the desired tone.

L

To stop ringing, press { ■}.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

59

GT15xxE.book Page 60 Wednesday, August 1, 2007 11:59 AM

Answering System

Answering system

Available model:

BB-GT1520/BB-GT1522/BB-GT1540

This unit contains an answering system which can answer and record calls for you when you are unavailable to answer the phone.

Important:

L

Only 1 person can access the answering system at a time.

L

When callers leave messages, the unit records the day and time of each message. Make sure the date and

time have been correctly set (page

29).

Memory capacity

The total recording capacity (including caller messages and voice memos) is about 45 minutes.

A maximum of 99 messages can be recorded.

L

If the message memory becomes full,

{

6}

on the base unit flashes rapidly.

Erase unnecessary messages (page

62).

L

When the message memory becomes full, the greeting message is different depending on your situation:

– If you use the pre-recorded greeting message, the unit automatically switches to another pre-recorded greeting message asking callers to call again later.

– If you recorded your own greeting message, the same message is still announced to callers even though their messages are not recorded.

Turning the answering system

on f

1

Press {IP/TEL} repeatedly until the display shows the desired line(s)

(n and/or m).

2

Press {s} to turn on the answering system.

L

The s indicator lights.

Note:

L

In standby mode, the display shows the line(s) set for the answering system (n and/or m).

Turning the answering system off

Press {s}.

L

The s indicator turns off.

Screening calls

While a caller is leaving a message, you can listen to the call through the base unit’s speaker. To adjust the speaker volume, press {<} or {>} repeatedly.

L

To answer the call using the base unit, press the flashing {TEL} or {IP}.

(BB-GT1540)

L

To answer the call using the handset, press {TEL} or {IP}.

Note:

L

To turn this feature off, see page 67.

60

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 61 Wednesday, August 1, 2007 11:59 AM

Greeting message

When the unit answers a call, callers are greeted by a greeting message. You can record your own greeting message or use a pre-recorded greeting message.

Recording your greeting

message f

You can record your own greeting message (max. 2 minutes) that is played when the answering system answers a call.

The greeting messages can be recorded:

– separately for either the IP line or landline.

– for both the IP line and landline using a common greeting.

If you do not record a greeting message, a pre-recorded greeting message is used.

1

Press {IP/TEL} repeatedly until the display shows the desired line(s)

(n and/or m).

2

{dr}

3

Within 10 seconds, press {dr} again.

4

After the base unit beeps, speak clearly about 20 cm away from the

MIC.

5

To stop recording, press {

■}.

Using a pre-recorded greeting message

If you erase or do not record your own greeting message, the unit plays a prerecorded greeting message for callers and asks them to leave messages.

playing.

Answering System

Playing back the greeting

message f

1

Press {IP/TEL} repeatedly until the display shows the desired line(s)

(n and/or m).

2

{dg}

Erasing your greeting

message f

1

Press {IP/TEL} repeatedly until the display shows the desired line(s)

(n and/or m).

2

Press {dg}, and then press {4} while your greeting message is

Listening to messages using the base unit

When new messages have been recorded, {6} on the base unit flashes.

Press {6} (centre of navigator key).

L

The base unit plays new messages including voice memos.

L

When you have no new messages, the base unit plays back all messages.

Playing back messages for the desired line(s)

1

Press {IP/TEL} repeatedly until the display shows the desired line(s)

(n and/or m).

2

Press {6} (centre of navigator key).

Note:

L

If you select the line(s), voice memos

are not played (page 63).

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

61

GT15xxE.book Page 62 Wednesday, August 1, 2007 11:59 AM

Answering System

Operating the answering system

Key

{>}

{

{

{

{

/{<}

<}

>}

■}

4}

Operation

Adjust the speaker volume

(during playback)

Repeat a message

(during playback)

*1

Skip a message

(during playback)

Pause a message

– To resume playback, press {6} (centre of navigator key).

– To stop playback completely, press

{

■} again.

Erase message currently playing

*1 If pressed within the first 5 seconds of a message, the previous message is played.

Listening to messages using the handset

When new messages have been recorded:

“New message” is displayed.

– The message indicator on the handset flashes slowly if the message alert

feature is turned on (page 66).

1

K

i 0

L

The handset plays new messages including voice memos.

L

When you have no new messages, the handset plays back all messages.

2

When finished, press {i}.

Note:

L

You can also listen to the messages as follows:

To play new messages:

K

i {#}{3}{2}{3}

To play all messages:

K

i {#}{3}{2}{4}

L

To switch to the receiver, press {s}.

Erasing all messages

Press {4} 2 times while the unit is not being used.

L

All messages including voice memos are erased.

Erasing all messages for the desired line(s)

1

Press {IP/TEL} repeatedly until the display shows the desired line(s)

(n and/or m).

2

Press {4} 2 times.

Calling back (Caller ID subscribers only)

If Caller ID information was received for the call, you can call the caller back while listening to the message.

1

Press M during playback.

L

To edit the number before calling back, press {. Then add or erase digits to the beginning of the number by pressing the desired dial key or ^.

2

Press ].

L

The indicated line is selected.

L

You can also select the line by pressing {TEL} or {IP}.

62

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 63 Wednesday, August 1, 2007 11:59 AM

Operating the answering system

You can also operate the answering system by pressing dial keys on the handset.

To use the following commands:

K

i {V}/{^}: “Answer System” i

M

Key

Pushing the joystick up or down.

{

1} or push the joystick left

Operation

Adjust the receiver/ speaker volume

(during playback)

Repeat message

(during playback)

*1

{

2} or push the joystick right

{

3}

Skip message

(during playback)

{

4}

Enter the

“Settings” menu

Play new messages

{

5}

{

9}/O

{

0}

Play all messages

Stop playback

Turn answering system off

{*}{

4}/W Erase message currently playing

{*}{

5}

{#}{

1}{8}

{#}{

{#}{

2}{8}

0}{8}

Erase all messages

Turn answering system on for IP line only

Turn answering system on for landline only

Turn answering system on for both

IP line and landline

Answering System

*1 If pressed within the first 5 seconds of a message, the previous message is played.

Erasing all messages

1

K

i {#}{3}{2}{5}

2

{V}

/{^}: “Yes” i M

L

When all items have been erased, “Erased” is displayed.

3

{i}

Voice memo

Recording a voice memo f

You can use the base unit to leave a voice memo (voice message) for yourself or someone else (max. 3 minutes). Voice memos can be played back later with the same operation used to play back answering system messages.

1

{ 7}

2

After the unit beeps, speak clearly about 20 cm away from the MIC.

3

To stop recording, press { ■}.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

63

GT15xxE.book Page 64 Wednesday, August 1, 2007 11:59 AM

Answering System

Remote operation

Using a touch tone phone, you can call your phone number from outside and access the unit to listen to messages.

The unit’s voice guidance prompts you to press certain dial keys to perform different operations.

Important:

L

In order to operate the answering system remotely, you must first turn on remote operation by setting a

remote code (page 64). This code

must be entered each time you operate the answering system remotely.

L

To call the unit via the IP line from a landline phone or mobile phone, you need an additional phone number you subscribed at www.joip.com other

than the joip number (page 4).

Turning remote operation on

N

A 3-digit remote code must be entered when operating the answering system remotely. This code prevents unauthorised parties from listening to your messages remotely. After you store your remote code, remote operation is possible. The default setting is “Off”.

1

K

i {#}{3}{0}{6}

2

To turn on remote operation, enter a

3-digit remote code. Enter the desired 3-digit remote code.

L

To turn off remote operation, press {*}.

3

M

i {i}

Note:

L

If you have stored the remote code, you can turn on the answering system by calling the unit even when it is

turned off (page 60). This call may be

answered before the ring delay

feature of the night mode (page 59)

activates. You need to select “30

sec.” for activating the ring delay feature.

Using the answering system remotely

1

Dial your phone number from a touch tone phone.

2

After the greeting message starts,

enter your remote code (page 64).

L

The unit plays back new messages.

3

Control the unit using remote

commands (page 65).

4

When finished, hang up.

Note:

L

When you press a key, press firmly.

Voice guidance

During remote operation, the unit’s voice guidance starts and prompts you to press {1} to perform a specific operation, or press {2} to listen to more available operations. Operations are presented by voice guidance in the following order:

– Play back all messages

– Play back new messages

– Record your message

– Erase all messages

– Record your greeting message

Note:

L

If you do not press any dial keys within

10 seconds after a voice guidance prompt, the unit disconnects your call.

64

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 65 Wednesday, August 1, 2007 11:59 AM

Remote commands

You can press dial keys to access certain answering system functions without waiting for the voice guidance to prompt you.

Key

{

{

{

{

{

{

1}

2}

4}

5}

9}

0}

{*}{

4}

Operation

Repeat message

(during playback)

*1

Skip message (during playback)

Play new messages

Play all messages

Stop recording

Stop playback

*2

Turn answering system off

Erase message currently playing

{*}{

5} Erase all messages

{#}{

1}{7} Record a greeting message for IP line only.

{#}{

2}{7} Record a greeting message for landline only.

{#}{

0}{7} Record a common greeting message for both IP line and landline.

{#}{

1}{8} Turn answering system on for IP line only.

{#}{

2}{8} Turn answering system on for landline only.

{#}{

0}{8} Turn answering system on for both IP line and landline.

{*}{#}

End remote operation

(or hang up).

Answering System

*1 If pressed within the first 5 seconds of a message, the previous message is played.

*2 To resume operation, enter a remote command within 15 seconds, or the voice guidance starts.

Turning on the answering system remotely

If the answering system is off, you can turn it on remotely by calling the selected

line in “Turning the answering system on f

”, page 60.

1

Dial the phone number from a touch tone phone.

2

Let the phone ring 20 times.

L

A long beep will be heard.

3

Enter your remote access code within 10 seconds after the long beep.

L

The unit answers your call with the greeting message.

L

You can hang up, or enter your remote code again and begin

remote operation (page 64).

Skipping the greeting message to leave a message

You can leave a message just as any outside caller can. Call your phone number. When the answering system picks up, press {*} to skip the greeting message and record your message after the beep.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

65

GT15xxE.book Page 66 Wednesday, August 1, 2007 11:59 AM

Answering System

Answering system settings

Number of rings N

You can change the number of times the phone rings before the unit answers calls. The default setting is “4 Rings”.

“Toll saver”

*1

: The unit answers on the 2nd ring when new messages have been recorded, and on the 5th ring when there are no new messages. If you call your phone from outside to listen to new

messages (page 64), you will know that

there are no new messages when the phone rings for the 3rd time. You can then hang up without being charged for the call.

1

K

i {#}{2}{1}{1}

2

{V}

/{^}: Select the desired line.

3

{V}

/{^}: Select the desired setting.

4

M

i {i}

*1 l Depending on the condition of your network connection, “Toll

saver” may not be used for the IP line.

For Voice Mail service subscribers

Please note the following:

L

To use the Voice Mail service provided by your landline service provider/A rather than the unit’s answering system, turn off the answering system

(page 60).

L

To use this unit’s answering system rather than the Voice Mail service, please contact your landline service provider/A service provider to deactivate your Voice Mail service.

If your service provider cannot do this:

– Set this unit’s “Number of

Rings” setting so that this unit’s

66 answering system answers calls before the Voice Mail service does.

It is necessary to check the number of rings required to activate the

Voice Mail service before changing this setting.

– Change the number of rings of the

Voice Mail service so that the answering system can answer the call first. To do so, consult your landline service provider/A service provider.

Caller’s recording time N

You can change the maximum message recording time allotted to each caller.

The default setting is “3 Minutes”.

1

K

i {#}{3}{0}{5}

2

{V}

/{^}: Select the desired line.

3

{V}

/{^}: Select the desired setting.

4

M

i {i}

Message alert N

You can select whether or not the message indicator on the handset flashes (slowly) when new messages are recorded. The default setting is

“Off”.

Important:

L

If there are new Voice Mail messages

(page 68), the message indicator on

the handset also flashes slowly.

1

K

i {#}{3}{4}{0}

2

{V}

/{^}: Select the desired setting.

3

M

i {i}

Note:

L

While message alert feature is on, the battery operating time is shortened

(page 22).

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 67 Wednesday, August 1, 2007 11:59 AM

Call screening N

This feature allows you to listen to a message from the base unit while the answering system is recording the message. The default setting is “On”.

1

K

i {#}{3}{1}{0}

2

{V}

/{^}: Select the desired setting.

3

M

i {i}

Answering System

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

67

GT15xxE.book Page 68 Wednesday, August 1, 2007 11:59 AM

Voice Mail Service

Using Voice Mail service

This unit is compatible with Voice Mail services offered by your landline service provider and A. After you subscribe to these services, the Voice Mail system of your service provider will answer calls for you when you are unavailable to answer the phone or when your line is busy. Messages are recorded by your

Voice Mail service provider, not your telephone.

L k

Please contact your landline service provider for details.

L l

Please visit www.joip.com or contact the A service provider for details.

Important:

L

To use the Voice Mail service rather than the unit’s answering system, turn

off the answering system (page 60).

even after you have listened to all new messages, turn it off by pressing and holding {i} on the handset until a beep sounds.

Message alert N

You can select whether or not the message indicator on the handset flashes (slowly) when there are new recorded messages in the Voice Mail system. The default setting is “Off”.

Important:

L

If there are new messages in the

answering system (page 60), the

message indicator on the handset also flashes slowly. (BB-GT1520/BB-

GT1522/BB-GT1540)

1

K

i {#}{3}{4}{0}

2

{V}

/{^}: Select the desired setting.

3

M

i {i}

Note:

L

While message alert feature is on, the battery operating time is shortened

(page 22).

Voice Mail message indication l

The unit lets you know that you have new Voice Mail messages in the following ways:

– The 0 indicator on the base unit flashes.

“VoiceMail:joip” is displayed on the handset. “VoiceMail:joip” indicates the messages received by

A.

– The message indicator on the handset flashes slowly if the message alert

feature is turned on (page 68).

To listen to your Voice Mail messages received by A, access the A Voice

Mail from the A service menu using

the handset (page 75).

Note:

L

If the handset or base unit still indicates there are new messages

68

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 69 Wednesday, August 1, 2007 11:59 AM

Intercom features between handsets

Intercom calls

Intercom calls can be made between handsets.

Note:

L

If you receive an outside call while talking on the intercom, the interrupt tone sounds. To answer the call, press

{

TEL} or {IP}. To turn the interrupt

tone off, see page 51.

L

When paging, the paged handset beeps for 1 minute.

Intercom Features

1

During an outside call, press {INT} to put the call on hold.

2

To page a handset, enter its extension number ({1} – {6}).

3

Wait for the paged party to answer.

L

If the paged party does not answer, press {TEL} or {IP} to return to the outside call.

4

To complete the transfer:

Press {i}.

L

The outside call is being routed to the handset.

To make a conference call:

Press w.

L

To leave the conference, press

{i}

. The other 2 parties can continue the conversation.

L

To put the outside call on hold, press {a}. To resume the conference, press w.

Making an intercom call

1

{

INT}

2

To page a handset, enter its extension number ({1} – {6}).

L

To stop paging, press {i}.

3

When you finish talking, press {i}.

Answering an intercom call

1

Press ] to answer the page.

2

When you finish talking, press {i}.

Note:

L

The ringer volume for intercom calls follows the higher volume level of the

2 lines (page 52).

L

When the ringer volume is set to off for both lines, the handset rings at a low level for intercom calls.

Answering a transferred call

Press ] to answer the page.

L

After the paging party disconnects, you can talk to the outside caller.

Auto intercom/Room monitor

This feature allows you to:

– answer an intercom call without pressing any buttons on the handset.

– listen to the sound in a room where the handset is located.

Transferring calls, conference calls

Outside calls can be transferred between 2 handsets. 2 handsets can have a conference call with an outside party.

Turning auto intercom on/off

“Off” (Default): Turns this feature off.

“On (Ringer On)”: When an intercom call is received, the handset rings 2 times then the speakerphone is automatically turned on.

“On (Ringer Off)”: When an intercom call is received, the handset does not ring and the speakerphone is automatically turned on. This allows you to easily monitor a baby’s room, for

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

69

GT15xxE.book Page 70 Wednesday, August 1, 2007 11:59 AM

Intercom Features

example, from different areas of the house.

1

K

i {#}{2}{7}{3}

2

{V}

/{^}: Select the desired setting.

3

M

i {i}

Note:

L

Auto intercom cannot be used when:

– your handset is receiving a transferred outside call.

– all handsets are being paged by the base unit.

Answering an intercom call using auto intercom

1

When you are paged by another handset, speak into the microphone.

L

To switch to the receiver, press

{s}

.

2

To end the intercom, press {i}.

Monitoring audio in a room

You can listen to the sound in a room where another handset is located.

Important:

L

Before using this feature, set auto intercom on the destination handset to

“On (Ringer Off)” to allow access by other handsets.

1

Call the destination handset (page

69).

L

You can listen to the audio.

2

To mute your sound output, press

1

if necessary.

3

Press {i} to stop monitoring.

Intercom features between the handset and base unit

Available model:

BB-GT1520/BB-GT1522/BB-GT1540

Intercom calls

Intercom calls can be made between the handset and base unit.

Note:

L

If you receive an outside call while talking on the intercom, the interrupt tone sounds. To answer the call:

– press {TEL} or {IP} on the handset.

– press {TEL} or {IP} on the base unit. (BB-GT1540)

To turn the interrupt tone off, see page

51.

L

When paging unit(s) for an intercom call, the paged unit(s) beeps for 1 minute.

Making an intercom call

Handset

1

{

INT}

2

To page the base unit, press {0}.

L

To stop paging, press {i}.

3

When you finish talking, press {i}.

Base unit

BB-GT1520/BB-GT1522

1

{x}

L

All handsets beep for 1 minute.

L

To stop paging, press {x}.

2

When you finish talking, press {x}.

70

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 71 Wednesday, August 1, 2007 11:59 AM

Note:

L

You can locate a misplaced handset by paging it.

BB-GT1540

1

{x}

2

To page a specific handset, enter its extension number ({1} – {6}).

To page all handsets, press {0} or wait for a few seconds.

L

The paged handset(s) beeps for 1 minute.

L

To stop paging, press {x}.

3

When you finish talking, press {x}.

Note:

L

You can locate a misplaced handset by paging it.

Answering an intercom call

Handset

1

Press ] to answer the page.

2

When you finish talking, press {i}.

Base unit

1

Press {x} to answer the page.

2

When you finish talking, press {x}.

Note for handset and base unit:

L

The ringer volume for intercom calls follows the higher volume level of the

2 lines (page 52, 59).

L

When the ringer volume is set to off for both lines, the handset or base unit rings at a low level for intercom calls.

Answering an intercom call using auto intercom

Before using the auto intercom, turn auto

intercom on (page 69).

Handset

1

When you are paged by the base unit, speak into the microphone.

Intercom Features

L

To switch to the receiver, press

{s}

.

2

To end the intercom, press {i}.

Monitoring audio in a room using auto intercom (BB-GT1540)

Base unit

You can listen to the sound in a room where the handset is located using the

auto intercom (page 69).

Important:

L

Before using this feature, set auto intercom on the destination handset to

“On (Ringer Off)” to allow access

by the base unit (page 69).

1

Call the destination handset (page

71).

L

You can listen to the audio.

2

To mute your sound output, press

{T}

if necessary.

3

Press {x} to stop monitoring.

Transferring calls, conference calls (BB-GT1540)

Outside calls can be transferred between the handset and base unit. The handset and base unit can have a conference call with an outside party.

Handset

1

During an outside call, press {INT} to put the call on hold.

2

To page the base unit, press {0}.

3

Wait for the paged party to answer.

L

If the paged party does not answer, press {TEL} or {IP} to return to the outside call.

4

To complete the transfer:

Press {i}.

L

The outside call is being routed to the base unit.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

71

GT15xxE.book Page 72 Wednesday, August 1, 2007 11:59 AM

Intercom Features

To make a conference call:

Press w.

L

To leave the conference, press

{i}

. The other 2 parties can continue the conversation.

L

To put the outside call on hold, press {a}. To resume the conference, press w.

Base unit

1

During an outside call, press {x} to put the call on hold.

2

To page a specific handset, enter its extension number ({1} – {6}).

To page all handsets, press {0} or wait for a few seconds.

L

Even if you call all handsets, only the handset user who answers first can take the transferred call.

3

Wait for the paged party to answer.

L

If the paged party does not answer, press {x} to return to the outside call.

4

To complete the transfer:

Press {s}.

L

The outside call is being routed to the handset.

To make a conference call:

Press {5}.

L

To leave the conference, press

{s}

. The other 2 parties can continue the conversation.

L

To put the outside call on hold, press {a}. To resume the conference, press {5}.

Note for handset and base unit:

L

After the paging party disconnects, you can talk to the outside caller.

Answering a transferred call

Handset

Press ] to answer the page.

Base unit

Press {s} to answer the page.

72

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 73 Wednesday, August 1, 2007 11:59 AM

Using A service features

A service offers not only IP phone features but other various features such as ringtones, text messages, community directory, and more. For further information, visit the A website at www.joip.com

Importing downloaded phonebook items to the

handset N

You can add and edit phonebook items by accessing your account on the A website (www.joip.com), then downloading your web phonebook to the base unit.

“New phonebook” is displayed after new phonebook items are downloaded.

Import them to a handset.

1

n

i K

2

{V}

/{^}: “Import phonebook”

3

M

Note:

L

“New phonebook” disappears from all handsets’ displays after the handset imported the phonebook items. Other handset users can import the phonebook items separately.

Importing downloaded

ringtones to the handset N

You can download a maximum of 3 ringtones to the base unit using the A website (www.joip.com). After new ringtones are downloaded, “New

ringer” is displayed on the handset.

You can import these ringtones to the handset. A maximum of 3 imported ringtones can be stored in a handset at

A Service

one time. You can also set them as the handset ringer(s).

1

K

i {#}{1}{7}{0}

2

{V}

/{^}: Select the desired ringtone.

3

M

L

“Receiving” is displayed on the handset while importing.

L

When the item has been imported, “Completed” is displayed.

4

To assign the ringtone to a line:

{V}

/{^}: “Yes” i M

Not to assign the ringtone to a line:

{V}

/{^}: “No” i M i Go to

step 6.

5

{V}

/{^}: Select the desired line.

L

To import other ringtones, repeat

from step 2.

6

{i}

Note:

L

“New ringer” disappears from all

handset displays after step 1. Other

handset users can import the ringtones separately.

L

To assign a ringtone to a line later, see

page 54.

L

To use a ringtone for a ringer ID of a

handset phonebook item, see page

40, 41.

L

To use a ringtone for the alarm, see

page 55.

L

In step 3, if “Overwrite?” is

displayed, 3 ringtones have already been imported. To overwrite with the new one, select a ringtone you do not need. i M

L

If the overwritten ringtone was used for:

– a handset ringer, “Ringtone 1”

(landline) or “Ringtone 2” (IP line) is used instead

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

73

GT15xxE.book Page 74 Wednesday, August 1, 2007 11:59 AM

A Service

– a ringer ID of a handset phonebook

item, the ringer set on page 54 is

used instead

– the alarm, “Ringtone 1” is used instead

L

Downloaded ringtones are temporarily stored in the base unit.

When a 4th ringtone is downloaded to the base unit, it replaces the oldest one. All ringtones will be erased by

pressing {IP RESET} (page 78).

A text messages N

You can view the A text messages using a handset.

The unit can receive a maximum of 88 messages. The number of received messages may decrease depending on the size of each message as follows:

Size of message

320 characters

*1

12 or less characters

Maximum number of messages

14

88

*1 The maximum number of characters per message

Note:

L

The unit erases the oldest message when the message memory is full. We recommend you protect the

messages you want to keep (page

74).

for the Voice Mail or answering

system are on (page 66, 68).

1

K

i {#}{3}{6}{0}

L

The numbers of the new messages and total messages are displayed.

2

{V}

/{^}: Select the desired item. i

M

L

To view another text message,

press U and repeat step 2.

3

{i}

Note:

L

A Q is displayed in the message list for a message which has already been viewed by any handset.

L

If an arrow (>) is displayed, some information is not shown. Push the joystick right to see the remaining information. To return to the previous display, push the joystick left.

L

“New joip message” disappears from all handset displays after viewing all new A text messages.

Protecting a A text message

You can protect a maximum of 8 messages. When the message memory is full, protected messages are not erased until you release the protection.

Press | while viewing a message.

L

To release the protection, press | again.

Viewing A text messages

When new text messages have been received:

“New joip message” is displayed if the A text message alert is on

(page 75).

– The message indicator on the handset also flashes slowly if both the A text message alert and the message alert

74

Erasing a A text message

1

While viewing the message list or message, press W.

2

{V}

/{^}: “Yes”

3

M

i {i}

Erasing all A text messages

You can erase all text messages except

protected messages (page 74).

1

K

i {#}{3}{6}{0}

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 75 Wednesday, August 1, 2007 11:59 AM

2

While viewing the number of the total text messages, press W.

3

{V}

/{^}: “Yes”

4

M

i {i}

Turning the A text message alert on/off

You can select whether or not “New

joip message” is displayed on the handset when new A messages have been received. The default setting is

“On”.

1

K

i {#}{3}{6}{1}

2

{V}

/{^}: Select the desired setting.

3

M

i {i}

“joip service” menu N

Some A services such as Voice Mail can be accessed from the “joip

service” menu using the handset.

This menu can be downloaded from

A. Select the desired service from the

“joip service” menu. The access number is automatically dialled via the IP line. For further information about the services, visit www.joip.com

1

K

i {#}{5}{3}{0}

L

The available menu is displayed.

2

{V}

/{^}: Select the desired item. i

M

L

The unit dials to access the service.

3

When finished, press {i}.

A Service

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

75

GT15xxE.book Page 76 Wednesday, August 1, 2007 11:59 AM

Useful Information

Belt clip

You can hang the handset on your belt or pocket using the supplied belt clip.

To attach the belt clip

Wall mounting for charger

Available model:

BB-GT1522

1

Drive the screws (not supplied) into the wall.

25.4 mm

Screws

To remove the belt clip

While pressing the top of the clip (

A), pull the right edge in the direction of the arrow (

B).

(220-240 V, 50 Hz)

2

Mount the charger (

A), then slide it down (

B) and to the right (C) until it is secure.

A

B

A

B

C

76

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 77 Wednesday, August 1, 2007 11:59 AM

Registering a handset

The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, register the handset.

Important:

L

If you have already deregistered the

handset, perform steps 2 and 3 only.

1

Handset:

K

i {#}{1}{3}{0}

2

Base unit:

BB-GT1500

Press and hold {x} until the 4 indicator flashes in red.

BB-GT1520/BB-GT1522/BB-

GT1540

Press and hold {x} until the registration tone sounds and the 4 indicator flashes in red.

L

If all registered handsets start ringing, stop ringing by pressing the same button. Then repeat this step.

L

After the 4 indicator starts flashing in red, the rest of the procedure must be completed within 90 seconds.

3

Handset:

[

4

Wait until “Enter Base PIN” is displayed, then enter the base unit

PIN (default: “0000”), then press

M

.

L

If you forget your PIN, see page

91.

L

When the handset has been registered successfully, _ will change to w. If the keytone is

turned on (page 52), a

confirmation tone will be heard.

Useful Information

Registering an additional handset

See page 9 for information on the

available model. Start from step 2.

Deregistering a handset

Handset

1

K

i {#}{1}{3}{1}

2

{

3}{3}{5} i M

3

{V}

/{^}: Select the handset you want to cancel. i M

4

{V}

/{^}: “Yes” i M

L

When you cancel a different handset than the one you are now using, press {i} to exit.

Base unit

BB-GT1540

1

Press and hold {x} until the registration tone sounds, and the 4 indicator flashes in red.

2

Press and hold the handset number

({1} - {6}) that you want to cancel until a confirmation tone sounds.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

77

GT15xxE.book Page 78 Wednesday, August 1, 2007 11:59 AM

Useful Information

IP RESET button

Using the {IP RESET} button on the bottom of the base unit, you can reset the Internet connection settings.

– DHCP connection mode is returned to

“On” (default).

– If you set the static IP address and other settings (“Subnet mask”,

“Default gateway”, “DNS1”,

“DNS2”), they are erased.

– The Terms of Use for the A services you previously agreed to is cancelled. You need to agree to it again using the handset.

(www.joip.com) to the base unit are erased. If necessary, import ringtones and phonebook data to the handset

before pressing {IP RESET} (page

73).

L

A text messages are not affected.

L

Entries in the handset phonebook, caller list, and redial list are not affected.

L

The unit’s settings (excluding internet connection settings) are not reset to default.

IP RESET

{

IP RESET}

1

Make sure that the AC adaptor is connected.

Press and hold {IP RESET} for about 7 seconds with a pointed object such as a pen.

2

“Please read joip Terms of

Use. Agree?” is displayed on the handset. Read the Terms of Use for the A services on the supplied leaflet or at www.joip.com and press

M

.

3

Wait until the 4 indicator turns green.

L

If necessary, set the Internet

connection settings again (page

30).

Note:

L

Ringtones and phonebook data downloaded from the A website

78

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 79 Wednesday, August 1, 2007 11:59 AM

Useful Information

Character entry

The dial keys are used to enter characters and numbers. Each dial key has multiple characters assigned to it. The available character entry modes are Alphabet (ABC),

Numeric (0-9), Greek (F), Extended 1 (G), Extended 2 (H), and Cyrillic

(I). When in these entry modes except Numeric, you can select which character is entered by pressing a dial key repeatedly.

– Use the joystick to move the cursor.

– Press dial keys to enter characters and numbers.

– Press ^ to erase the character or number highlighted by the cursor. Press and hold ^ to erase all characters or numbers.

– Press {*} to switch between uppercase and lowercase.

L

To enter another character located on the same dial key, push the joystick right to move the cursor to the next space, then press the appropriate dial key.

Character entry modes

Several character entry modes can be used when entering text. The characters that can be entered depend on the entry mode.

Characters available in each character entry mode

When a character entry screen is displayed on the handset:

/

i Select a character entry mode. i M

Alphabet character table (ABC)

Numeric entry table (0-9)

Greek character table (M)

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

79

GT15xxE.book Page 80 Wednesday, August 1, 2007 11:59 AM

Useful Information

Extended 1 character table (N)

Extended 2 character table (O)

Cyrillic character table (P)

80

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 81 Wednesday, August 1, 2007 11:59 AM

Useful Information

Error messages

If the unit detects a problem, one of the following messages is shown on the handset display.

Display message

Busy

Free calls! Plug internet cable. www.joip.com

Cause/solution

L

The called handset or base unit is in use.

L

Privacy mode is on for the call you tried to join

(page 34).

L

Other units are in use and the system is busy.

Try again later.

L

The line is in use. Wait until i or S disappears from the handset display.

L

Confirm the Ethernet cable is properly

connected (page 18).

L

Check the base unit’s IP address using the handset: K i {#}{5}{0}{1}

If necessary, change the base unit’s static IP

address (page 30).

L

Check your network devices’ (router, modem, etc.) connections. If the connections are made properly but the problem persists, check your network devices’ (router, modem, etc.) settings.

L

If you cannot access Internet Web pages using your computer, check to see if your

Internet service provider is having connection issues in your area.

L

Check your device connections with the

installation instructions (page 18). The order

in which you turn on the devices is important.

L

Many installation issues can be resolved by resetting all the equipment. First, shut down your modem, router, base unit, and computer.

Then turn the devices back on one at a time in this order: modem, router, base unit, computer.

L

For more troubleshooting help, visit www.joip.com or contact the A service provider.

L

You have not received the A number.

Install the base unit to your local network

(page 18, 30).

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

81

GT15xxE.book Page 82 Wednesday, August 1, 2007 11:59 AM

Useful Information

Display message

Dial locked

Error

Failed

Incomplete

Invalid setting joip message

Memory Empty

Memory Full

*1

Memory full. Memory limited to 8 MSGs.

Memory Empty

Messages full

*1

Cause/solution

L

Dial lock is turned on. To turn it off, see page

58.

L

The software update of the base unit has failed. Confirm that the IP line is not being

used, and try again (page 57).

L

The entered password was wrong in programming dial lock. Enter the correct password.

L

The handset you tried to copy phonebook items to is in use.

L

The handset you tried to copy phonebook items to is out of area.

L

The destination handset’s phonebook memory is full. Erase unnecessary items from

the destination handset’s phonebook (page

41).

L

The Internet connection settings are not

correct. Enter the correct settings (page 30).

L

There are no A text messages (page 74).

L

The message memory for the answering system is full. Erase unnecessary messages

(page 62).

L

The maximum number of A text messages you can protect is 8. To release a protected

text message, see page 74.

L

Your phonebook or redial list is empty.

L

There is no downloaded data (phonebook data, ringtone data, or A service menu data) in the base unit.

L

The unit is not registered to the A service.

Check the connections (page 18) and confirm

the 4 indicator lights in green (page 23).

L

The message memory for the answering system is full. Erase unnecessary messages

(page 62).

82

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 83 Wednesday, August 1, 2007 11:59 AM

Useful Information

Display message

No link to base. Move closer to base, try again.

Phonebook Memory Full

Please hang up and try again.

Please read joip Terms of Use. Agree?

This message is not erasable.

This message contains invalid characters.

Cause/solution

L

The handset has lost communication with the base unit. Move closer to the base unit, and try again.

L

Unplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again.

L

The handset’s registration may have been

cancelled. Re-register the handset (page 77).

L

There is no space to store new items in the

phonebook. Erase unnecessary items (page

41).

L

A handset button was pressed while the handset was on the base unit or charger. Lift the handset and press the button again.

L

You have not agreed to the Terms of Use for the A services. To use the A IP line, you

need to agree to it using the handset (page

19).

L

L

The protected messages remain. All other messages are erased.

The characters the unit cannot recognise are replaced with “_”.

*1 BB-GT1520/BB-GT1522/BB-GT1540

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

83

GT15xxE.book Page 84 Wednesday, August 1, 2007 11:59 AM

Useful Information

Troubleshooting

General use

Problem

The unit does not work.

l

I cannot hear a dial tone for the IP line.

Cause/solution

L

Make sure the battery is installed correctly

and fully charged (page 19, 21).

L

Check the connections (page 18).

L

Unplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again.

L

The handset has not been registered to the

base unit. Register the handset (page 77).

L

Confirm the Ethernet cable is properly

connected (page 18).

L

You have not agreed to the Terms of Use for the A services. To use the A IP line, you

need to agree to it using the handset (page

19).

L

Check the base unit’s IP address using the handset: K i {#}{5}{0}{1}

If necessary, change the base unit’s static IP

address (page 30).

L

Check your network devices’ (router, modem, etc.) connections. If the connections are made properly but the problem persists, check your network devices’ (router, modem, etc.) settings.

L

Many installation issues can be resolved by resetting all the equipment. First, shut down your modem, router, base unit, and computer.

Then turn the devices back on one at a time in this order: modem, router, base unit, computer.

L

If you cannot access Internet Web pages using your computer, check to see if your

Internet service provider is having connection issues in your area.

L

For more troubleshooting help, visit www.joip.com or contact the A service provider.

84

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 85 Wednesday, August 1, 2007 11:59 AM

Useful Information

Problem

k

I cannot hear a dial tone for the landline.

The indicator on the top right of the handset flashes slowly.

Cause/solution

L

Confirm the telephone line cord is properly

connected (page 18).

L

Disconnect the unit from the telephone line and connect a known working telephone. If the working telephone operates properly, contact Panasonic service personnel to have the unit repaired. If the working telephone does not operate properly, contact your landline service provider.

L

New messages have been received. Listen to

the new messages (page 61).

*1

L l

New Voice Mail messages have been recorded. Listen to the new Voice Mail

messages, see page 68.

L

New A text messages have been received.

To view the text messages, see page 74.

L

Change the display language (page 29).

I have changed the display language to a language I cannot read.

*1 BB-GT1520/BB-GT1522/BB-GT1540

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

85

GT15xxE.book Page 86 Wednesday, August 1, 2007 11:59 AM

Useful Information

4

(Status) indicator

Problem

The 4 indicator continues flashing in amber.

The 4 indicator flashes in amber rapidly although the IP address was acquired.

The 4 indicator lights in amber although the Ethernet cable is connected properly.

Cause/solution

L

An IP address may not have been acquired or the static IP address is not appropriate. Check the base unit’s IP address using the handset:

K

i {#}{5}{0}{1}

– If necessary, change the base unit’s static

IP address (page 30).

– If an IP address was not acquired, check your network devices’ (router, modem, etc.) connections. If the connections are made properly but the problem persists, check your network devices’ (router, modem, etc.) settings.

L

Many installation issues can be resolved by resetting all the equipment. First, shut down your modem, router, base unit, and computer.

Then turn the devices back on one at a time in this order: modem, router, base unit, computer.

L

If you cannot access Internet Web pages using your computer, check to see if your

Internet service provider is having connection issues in your area.

L

For more troubleshooting help, visit www.joip.com or contact the A service provider.

L

Unplug the base unit’s AC adaptor to reset the unit, then reconnect the AC adaptor. If the 4 indicator is still flashing in amber rapidly, there may be a problem with the base unit hardware. Contact Panasonic service personnel.

L

The base unit’s IP address may conflict with the IP addresses of other devices on your local network. Check the base unit’s static IP address using the handset: K i

{#}{

5}{0}{1}, then check the IP addresses of the other devices on your local network. If necessary, change the base unit’s static IP

address (page 30).

86

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 87 Wednesday, August 1, 2007 11:59 AM

Useful Information

Problem

The 4 indicator is off.

Cause/solution

L

The power of the base unit is off.

L

You have not agreed to the Terms of Use for the A services. To use the A IP line, you

need to agree to it using the handset (page

19).

L

The Ethernet cable is not connected properly.

Connect it.

L

Your network devices (hub, router, etc.) are turned off. Check the LEDs for the link status of the devices.

Programmable settings

Problem

I cannot program items.

While programming, the handset starts to ring.

I cannot register a handset to a base unit.

Cause/solution

L

Programming is not possible while either another handset or the base unit is being used. Try again later.

L

Programming is not possible while the base unit is downloading data from the A service. Wait until the 4 indicator stops flashing and lights in steady green.

L

A call is being received. Answer the call and start again after hanging up.

L

The maximum number of handsets (6) are already registered to the base unit. Cancel unused handset registrations from the base

unit (page 77).

L

You entered the wrong PIN number. If you

forget your PIN, see page 91.

L

Place the handset and the base unit away from other electrical appliances.

Battery recharge

Problem

I fully charged the battery, but

3

continues to flash, or 4 is displayed.

The handset display is blank.

Cause/solution

L

Clean the charge contacts and charge again

(page 21).

L

The battery may need to be replaced with new

ones (page 22).

L

Confirm that the battery are properly installed.

L

Fully charge the battery (page 21).

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

87

GT15xxE.book Page 88 Wednesday, August 1, 2007 11:59 AM

Useful Information

Making/answering calls, intercom

Problem

w

is displayed, but I cannot make a call.

Static is heard, sound cuts in and out. Interference from other electrical units.

The handset does not ring.

The base unit does not ring.

*1

I cannot make a call.

Cause/solution

L

The handset and base unit could not communicate for some reason, such as interference from other electrical appliances.

Perform the following:

– Move the handset and base unit away from other electrical appliances such as antennas and mobile phones.

– Move closer to the base unit.

L

Move the handset and base unit away from other electrical appliances.

L

Move closer to the base unit.

L k

Your unit is connected to a landline with

DSL service. We recommend connecting a filter (contact your DSL service provider) to the telephone line between the base unit and the telephone line jack.

L

The ringer volume is turned off. Adjust it (page

52).

L

The night mode feature is turned on. To turn it

off, see page 58.

L

The ringer volume is turned off. Adjust it (page

59).

L

The night mode feature is turned on. To turn it

off, see page 58.

L l

Check if the 4 indicator is lit in green.

If it is not lit in green, see “4 (Status)

indicator” (page 86).

L l

You cannot make a call while the base unit is downloading the software update. Wait until the 4 indicator stops flashing and changes to steady green.

L

You may have selected the wrong line by pressing {TEL} or {IP}. Select the appropriate line to call the phone number.

L

The base unit or another handset is in use. Try again later.

L

Dial lock is turned on. To turn it off, see page

58.

88

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 89 Wednesday, August 1, 2007 11:59 AM

Useful Information

Problem

l

I cannot make a call

using a mobile phone.

*1

I cannot page the handset.

I cannot page the base unit.

l

I answered a call when the phone rang, but the call was disconnected.

l

During a conversation, the following occurs:

– noise is heard.

– the sound is interrupted.

– the sound is delayed.

*1

Cause/solution

L

The IP line or the answering system is in use.

Try again later.

L

The remote code of the answering system is the default setting. You need to set your own

remote code for security (page 64).

L

The paged handset is too far from the base unit.

L

The paged handset is in use. Try again later.

L

The base unit is in use. Try again later.

L

The ringer may continue to sound for several seconds after the caller hangs up because of the time lag of the signal transmission.

L

It may be caused by someone using a computer connected to the same network as the unit.

L

Confirm the speed of Internet connection. The unit requires 100 kbps for each upstream and downstream. If less than 100 kbps is provided, visit www.joip.com or contact the

A service provider.

*1 BB-GT1520/BB-GT1522/BB-GT1540

Caller ID

Problem

The handset does not display the caller information.

Cause/solution

L

You have not subscribed to Caller ID.

k

Contact your landline service provider to subscribe.

l

Visit www.joip.com or contact the A service provider to subscribe.

L

The caller requested not to send caller

information (page 44).

L k

Generally, caller information is displayed from the 2nd ring.

L k

Your unit is connected to a landline with

DSL service. We recommend connecting a filter (contact your DSL service provider) to the telephone line between the base unit and the telephone line jack.

L k

Other telephone equipment may be interfering with this unit. Disconnect the other equipment and try again.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

89

GT15xxE.book Page 90 Wednesday, August 1, 2007 11:59 AM

Useful Information

Problem Cause/solution

I cannot access the caller list.

L

Someone is viewing the caller list from another handset.

A service features

Problem

I cannot import phonebook data or ringtone data to the handset.

I cannot view the A text message.

Cause/solution

L

While the base unit is downloading data excluding the base unit software, you cannot import phonebook data or ringtone data to the handset. Wait until the 4 indicator stops flashing and lights in steady green.

L

Someone is viewing a A text message from another handset.

L

While the base unit is downloading data excluding the base unit software, you cannot view the A text message. Wait until the 4 indicator stops flashing and lights in steady green.

Answering system (BB-GT1520/BB-GT1522/BB-GT1540)

Problem

I cannot listen to messages from a remote location.

The unit does not record new messages.

Cause/solution

L

A touch tone phone is required for remote operation.

L

Enter the remote code correctly and press

each key firmly (page 64).

L

The answering system is off. Turn it on (page

65).

L

The answering system is not turned on for the line you wish to record messages from. Select the desired line or both lines by pressing

{

IP/TEL} on the base unit repeatedly, then

turn the answering system on (page 60, 65).

L

The message memory is full. Erase

unnecessary messages (page 62, 63).

L

The answering system is activated for both lines, and the 1st caller is leaving a voice message. The 2nd caller cannot leave a message, but the caller information will be

stored (page 45).

L

If you subscribe to the Voice Mail service, messages are recorded by the landline service provider/A not your telephone

(page 66).

90

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 91 Wednesday, August 1, 2007 11:59 AM

Useful Information

Problem

I cannot operate the answering system.

Cause/solution

L

Someone is operating the answering system.

L

If someone is talking on a conference call, you may not be able to operate the answering system. Try again later.

Dial lock/Base unit PIN

Important:

L

Anyone can turn off the dial lock/base unit PIN using the following method.

Be sure to keep these Operating Instructions in a safe place in order to prevent unauthorised persons from using your phone without permission.

Problem

I cannot remember the dial lock password.

I cannot remember the PIN.

Cause/solution

L

Turn the dial lock off using the following method.

1

K

i {#}{2}{5}{1}

2

Press {*}{7}{0}{0}{0}.

3

Press M 2 times. i {i}

L

Change the PIN using the following method.

1

K

i {#}{1}{3}{2}

2

Press {*}{7}{0}{0}{0}.

3

Enter the new 4-digit base unit PIN. i

M

i {i}

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

91

GT15xxE.book Page 92 Wednesday, August 1, 2007 11:59 AM

Useful Information

Open Source Software

Parts of this product use Open Source Software. Relevant conditions apply to this software. Panasonic cannot accept inquiries regarding the content of the following copyright and license information.

<<NetBSD kernel>>

This product uses a part of NetBSD kernel.

The use of a part of NetBSD kernel is based on the typical BSD style license below.

Copyright (c)

The Regents of the University of California. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software

must display the following acknowledgement:

This product includes software developed by the University of

California, Berkeley and its contributors.

4. Neither the name of the University nor the names of its contributors

may be used to endorse or promote products derived from this software

without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS

``AS IS'' AND

ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED

TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS

BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS

OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN

ANY WAY

92

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 93 Wednesday, August 1, 2007 11:59 AM

Useful Information

OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY

OF SUCH DAMAGE.

-----

However, parts of the NetBSD Kernel are provided with the following copyright notices.

Copyright (c) 1980, 1983, 1988, 1993 The Regents of the University of California.

All rights reserved.

Copyright (c) 1980, 1986, 1989, 1993 The Regents of the University of California.

All rights reserved.

Copyright (c) 1980, 1986, 1991, 1993 The Regents of the University of California.

All rights reserved.

Copyright (c) 1980, 1986, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1982, 1985, 1986, 1988, 1993, 1994 The Regents of the University of California. All rights reserved.

Copyright (c) 1982, 1986, 1988, 1990, 1993 The Regents of the University of

California. All rights reserved.

Copyright (c) 1982, 1986, 1988, 1990, 1993, 1994, 1995 The Regents of the

University of California. All rights reserved.

Copyright (c) 1982, 1986, 1988, 1990, 1993, 1995 The Regents of the University of California. All rights reserved.

Copyright (c) 1982, 1986, 1988, 1991, 1993 The Regents of the University of

California. All rights reserved.

Copyright (c) 1982, 1986, 1988, 1993 The Regents of the University of California.

All rights reserved.

Copyright (c) 1982, 1986, 1988, 1993, 1995 The Regents of the University of

California. All rights reserved.

Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of

California. All rights reserved.

Copyright (c) 1982, 1986, 1989, 1993 The Regents of the University of California.

All rights reserved.

Copyright (c) 1982, 1986, 1990, 1991, 1993 The Regents of the University of

California. All rights reserved.

Copyright (c) 1982, 1986, 1990, 1993 The Regents of the University of California.

All rights reserved.

Copyright (c) 1982, 1986, 1990, 1993, 1994 The Regents of the University of

California. All rights reserved.

Copyright (c) 1982, 1986, 1991, 1993 The Regents of the University of California.

All rights reserved.

Copyright (c) 1982, 1986, 1991, 1993, 1994 The Regents of the University of

California. All rights reserved.

Copyright (c) 1982, 1986, 1991, 1993, 1995 The Regents of the University of

California. All rights reserved.

Copyright (c) 1982, 1986, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1982, 1986, 1993, 1994 The Regents of the University of California.

All rights reserved.

Copyright (c) 1982, 1986, 1993, 1994, 1995 The Regents of the University of

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

93

GT15xxE.book Page 94 Wednesday, August 1, 2007 11:59 AM

Useful Information

California. All rights reserved.

Copyright (c) 1982, 1986, 1993, 1995 The Regents of the University of California.

All rights reserved.

Copyright (c) 1982, 1988, 1991, 1993 The Regents of the University of California.

All rights reserved.

Copyright (c) 1983, 1990, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1983, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1985, 1986, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1985, 1986, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1986, 1989, 1991, 1993 The Regents of the University of California.

All rights reserved.

Copyright (c) 1986, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1987, 1991, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1987, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1987, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1988 Regents of the University of California. All rights reserved

Copyright (c) 1988 Stephen Deering.

Copyright (c) 1988 University of Utah.

Copyright (c) 1988, 1989, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1988, 1991, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1988, 1992, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1988, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1989 The Regents of the University of California. All rights reserved.

Copyright (c) 1989, 1991, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1989, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1989, 1993, 1994 The Regents of the University of California. All rights reserved.

Copyright (c) 1990, 1991, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1990, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1991, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1991, 1993, 1994 The Regents of the University of California. All rights reserved.

Copyright (c) 1992 Regents of the University of California. All rights reserved.

Copyright (c) 1992, 1993 The Regents of the University of California. All rights

94

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 95 Wednesday, August 1, 2007 11:59 AM

Useful Information

reserved.

Copyright (c) 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1993 Adam Glass

Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.

Copyright (c) 1994 Gordon W. Ross

Copyright (c) 1994 Winning Strategies, Inc. All rights reserved.

Copyright (c) 1995 The Regents of the University of California. All rights reserved.

Copyright (C) 1995, 1996, 1997, and 1998 WIDE Project. All rights reserved.

Copyright (c) 1996 The Regents of the University of California. All rights reserved.

Copyright (c) 1996 John S. Dyson All rights reserved.

Copyright (c) 1996 Matt Thomas. All rights reserved.

Copyright (c) 1996 Matthew R. Green. All rights reserved.

Copyright (c) 1996 Paul Kranenburg

Copyright (c) 1996, 1997, 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1996, 2000 Christopher G. Demetriou. All rights reserved.

Copyright (c) 1996,1999 by Internet Software Consortium.

Copyright (c) 1996-1999 by Internet Software Consortium.

Copyright (c) 1997 Jonathan Stone and Jason R. Thorpe. All rights reserved.

Copyright (c) 1997 Christos Zoulas. All rights reserved.

Copyright (c) 1997 Manuel Bouyer. All rights reserved.

Copyright (c) 1997, 1998 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1997, 1998, 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1997, 1998, 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1997, 1998, 1999, 2002 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1997, 1998, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1997, 1998, 2001 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1997,98 The NetBSD Foundation, Inc. All rights reserved.

Copyright (C) 1997-2000 Sony Computer Science Laboratories Inc. All rights reserved.

Copyright (c) 1997-2002 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1998 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1998 Todd C. Miller <[email protected]> All rights reserved.

Copyright (c) 1998, 1999 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1998, 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1998, 1999, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1998, 2000 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1998, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1999 The NetBSD Foundation, Inc. All rights reserved.

Copyright (C) 1999 WIDE Project. All rights reserved.

Copyright (c) 1999, 2000 Jason L. Wright ([email protected]) All rights reserved.

Copyright (c) 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1999, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 2000 The NetBSD Foundation, Inc. All rights reserved.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

95

GT15xxE.book Page 96 Wednesday, August 1, 2007 11:59 AM

Useful Information

Copyright (c) 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 2000, 2001, 2002 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 2001 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 2002 The NetBSD Foundation, Inc. All rights reserved.

Copyright 1998 Massachusetts Institute of Technology. All rights reserved.

Copyright 2001 Wasabi Systems, Inc. All rights reserved. Portions

Copyright (c) 1993 by Digital Equipment Corporation. Portions

Copyright (c) 1995 by International Business Machines, Inc.

Copyright (c) 1983, 1989 The Regents of the University of California. All rights reserved.

Copyright (c) 1996 by Internet Software Consortium. All rights reserved.

Copyright (c) 1980, 1986, 1989 Regents of the University of California. All rights reserved.

Copyright (c) 1988 The Regents of the University of California. All rights reserved.

Copyright (c) 1992, 1993 The Regents of the University of California. All rights reserved.

Copyright (c) 1994 Christopher G. Demetriou. All rights reserved.

Copyright (c) 1997 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1999 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 2001 The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1996 Gardner Buchanan <[email protected]> All rights reserved.

Parts of the NetBSD Kernel are provided with the licenses that are slightly different from the above Berkeley-formed license. Please refer the source code of the NetBSD

Kernel about the details.

The source code of the NetBSD Kernel is provided by the NetBSD CVS

Repositories

(http://cvsweb.netbsd.org/bsdweb.cgi/), and this product includes parts of the source code in the following directories. http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/kern/ http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/net/ http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/netinet/

<<OpenSSL>>

The product includes software developed by the OpenSSL Project and it is used under the following license.

LICENSE ISSUES

==============

The OpenSSL toolkit stays under a dual license, i.e. both the conditions of

the OpenSSL License and the original SSLeay license apply to the toolkit.

See below for the actual license texts. Actually both licenses are BSD-style

Open Source licenses. In case of any license issues related to OpenSSL

please contact [email protected].

OpenSSL License

---------------

96

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 97 Wednesday, August 1, 2007 11:59 AM

Useful Information

/* ============================================================

========

* Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved.

*

* Redistribution and use in source and binary forms, with or without

* modification, are permitted provided that the following conditions

* are met:

*

* 1. Redistributions of source code must retain the above copyright

* notice, this list of conditions and the following disclaimer.

*

* 2. Redistributions in binary form must reproduce the above copyright

* notice, this list of conditions and the following disclaimer in

* the documentation and/or other materials provided with the

* distribution.

*

* 3. All advertising materials mentioning features or use of this

* software must display the following acknowledgment:

* "This product includes software developed by the OpenSSL Project

* for use in the OpenSSL Toolkit. (http://www.openssl.org/)"

*

* 4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to

* endorse or promote products derived from this software without

* prior written permission. For written permission, please contact

* [email protected].

*

* 5. Products derived from this software may not be called "OpenSSL"

* nor may "OpenSSL" appear in their names without prior written

* permission of the OpenSSL Project.

*

* 6. Redistributions of any form whatsoever must retain the following

* acknowledgment:

* "This product includes software developed by the OpenSSL Project

* for use in the OpenSSL Toolkit (http://www.openssl.org/)"

*

* THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND

ANY

* EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED

TO, THE

* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR

* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL

PROJECT OR

* ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT

* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

SERVICES;

* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT,

* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

97

GT15xxE.book Page 98 Wednesday, August 1, 2007 11:59 AM

Useful Information

* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF

ADVISED

* OF THE POSSIBILITY OF SUCH DAMAGE.

* ===========================================================

=========

*

* This product includes cryptographic software written by Eric Young

* ([email protected]). This product includes software written by Tim

* Hudson ([email protected]).

*

*/

Original SSLeay License

-----------------------

/* Copyright (C) 1995-1998 Eric Young ([email protected])

* All rights reserved.

*

* This package is an SSL implementation written

* by Eric Young ([email protected]).

* The implementation was written so as to conform with Netscapes SSL.

*

* This library is free for commercial and non-commercial use as long as

* the following conditions are aheared to. The following conditions

* apply to all code found in this distribution, be it the RC4, RSA,

* lhash, DES, etc., code; not just the SSL code. The SSL documentation

* included with this distribution is covered by the same copyright terms

* except that the holder is Tim Hudson ([email protected]).

*

* Copyright remains Eric Young's, and as such any Copyright notices in

* the code are not to be removed.

* If this package is used in a product, Eric Young should be given attribution

* as the author of the parts of the library used.

* This can be in the form of a textual message at program startup or

* in documentation (online or textual) provided with the package.

*

* Redistribution and use in source and binary forms, with or without

* modification, are permitted provided that the following conditions

* are met:

* 1. Redistributions of source code must retain the copyright

* notice, this list of conditions and the following disclaimer.

* 2. Redistributions in binary form must reproduce the above copyright

* notice, this list of conditions and the following disclaimer in the

* documentation and/or other materials provided with the distribution.

* 3. All advertising materials mentioning features or use of this software

* must display the following acknowledgement:

* "This product includes cryptographic software written by

* Eric Young ([email protected])"

* The word 'cryptographic' can be left out if the rouines from the library

* being used are not cryptographic related :-).

98

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 99 Wednesday, August 1, 2007 11:59 AM

Useful Information

* 4. If you include any Windows specific code (or a derivative thereof) from

* the apps directory (application code) you must include an acknowledgement:

* "This product includes software written by Tim Hudson ([email protected])"

*

* THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND

* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED

TO, THE

* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE

* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR

CONTRIBUTORS BE LIABLE

* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL

* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS

* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION)

* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT

* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING

IN ANY WAY

* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF

* SUCH DAMAGE.

*

* The licence and distribution terms for any publically available version or

* derivative of this code cannot be changed. i.e. this code cannot simply be

* copied and put under another distribution licence

* [including the GNU Public Licence.]

*/

<<MD5>>

This software uses the Source Code of RSA Data Security, Inc. described in the

RFC1321 (MD5 Message-Digest Algorithm).

----------------------------------------------------------------

Copyright (C) 1991-2, RSA Data Security, Inc. Created 1991. All rights reserved.

License to copy and use this software is granted provided that it is identified as the "RSA Data Security, Inc. MD5 Message-Digest

Algorithm" in all material mentioning or referencing this software or this function.

License is also granted to make and use derivative works provided that such works are identified as "derived from the RSA Data

Security, Inc. MD5 Message-Digest Algorithm" in all material mentioning or referencing the derived work.

RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular purpose. It is provided "as is"

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

99

GT15xxE.book Page 100 Wednesday, August 1, 2007 11:59 AM

Useful Information

without express or implied warranty of any kind.

These notices must be retained in any copies of any part of this documentation and/or software.

<<MT19937>>

The MT19937 software that Takuji Nishimura and Makoto Matsumoto developed

is contained, and this product shall be used subject to the following

license conditions.

Copyright (C) 1997 - 2002, Makoto Matsumoto and Takuji Nishimura,

All rights reserved.

Redistribution and use in source and binary forms, with or without

modification, are permitted provided that the following conditions

are met:

1. Redistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

3. The names of its contributors may not be used to endorse or promote

products derived from this software without specific prior written

permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND

CONTRIBUTORS

"AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR

A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE

COPYRIGHT OWNER OR

CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF

THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

<<thttpd>>

The thttpd software that ACME Labs developed is contained, and this product

100

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 101 Wednesday, August 1, 2007 11:59 AM

Useful Information

shall be used subject to the following license conditions.

Copyright 1995,1998,1999,2000 by Jef Poskanzer <[email protected]>.

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS

IS'' AND

ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED

TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS

BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS

OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN

ANY WAY

OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF

SUCH DAMAGE.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

101

GT15xxE.book Page 102 Wednesday, August 1, 2007 11:59 AM

Useful Information

Specifications

Standard:

DECT (Digital Enhanced Cordless

Telecommunications),

GAP (Generic Access Profile)

Number of channels:

120 Duplex Channels

Frequency range:

1.88 GHz to 1.9 GHz

Duplex procedure:

TDMA (Time Division Multiple Access)

Channel spacing:

1,728 kHz

Bit rate:

1,152 kbit/s

Modulation:

GFSK (Gaussian Frequency Shift

Keying)

RF transmission power:

Approx. 250 mW

Power source:

220–240 V AC, 50 Hz

Network interface:

10/100base-TX auto MDI/MDIX

Ethernet LAN port

Support codecs:

G.711

µ-law, G.711 A-law, G.726 (32k),

G.729A

Power consumption:

Base unit:

BB-GT1500

Standby: Approx. 3.0 W

Maximum: Approx. 6.5 W

BB-GT1520/BB-GT1522

Standby: Approx. 3.0 W

Maximum: Approx. 6.5 W

BB-GT1540

Standby: Approx. 3.0 W

Maximum: Approx. 6.9 W

Charger:

Standby: Approx. 1.1 W

Maximum: Approx. 5.2 W

102

Operating conditions:

5

°C–40 °C, 20 %–80 % relative air humidity (dry)

Dimensions:

Base unit: Approx. 82 mm × 189 mm ×

129 mm

Handset: Approx. 156 mm × 48 mm × 33 mm

Charger: Approx. 68 mm

× 82 mm × 87 mm

Mass (weight):

Base unit:

BB-GT1500

Approx. 310 g

BB-GT1520/BB-GT1522

Approx. 360 g

BB-GT1540

Approx. 390 g

Handset: Approx. 160 g

Charger: Approx. 80 g

Note:

L

Design and specifications are subject to change without notice.

L

The illustrations in these instructions may vary slightly from the actual product.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 103 Wednesday, August 1, 2007 11:59 AM

Useful Information

Conditions of guarantee

This guarantee is in addition to and does not in any way affect any statutory or other rights of consumer purchasers. If within the applicable guarantee period, the appliance proves to be defective by reason of faulty design, workmanship or materials, we undertake subject to the following conditions to have the defective appliance (or any part or parts there of) repaired or replaced free of charge.

1. The appliance shall have been purchased and used solely within either the UK or ROI and in accordance with standard operating instructions and the technical and/or Safety Standards required in the UK.

2. The appliance should be returned together with this guarantee and proof of date of purchase promptly on being found defective at the purchaser’s risk and expense to the authorised dealer from whom the appliance was purchased or to the nearest authorised dealer. All enquires must be through such dealers.

3. This guarantee shall not apply to damage caused through fire, accident, lightning, misuse, wear and tear, neglect, incorrect adjustment or repair, to damage caused through installation, adaption, modification or use in an improper manner or inconsistent with the technical and/or safety standards required in the country where this appliance is used, or to damage occurred during transit to or from the purchaser.

4. If at any time during the guarantee period any part or parts of the appliance are replaced with a part or parts not supplied or approved by us or of an objective quality safe and suitable for the appliance, or the appliance has been dismantled or repaired by any person not authorised by us, we shall have the right to terminate this guarantee in whole or in part immediately without further notice.

5. The purchaser’s sole and exclusive remedy under this guarantee against us is for the repair or replacement of the appliance or any defective part or parts and no other remedy, including, but not limited to, incidental or consequential damage or loss of whatsoever nature shall be available to the purchaser.

6. This guarantee shall not apply to batteries and any other items of limited natural life.

7. Our decision on all matters relating to complaints shall be final. Any appliance or defective part which has been replaced shall become our property.

8. The guarantee period applicable to this product shall be 12 months.

Please keep these operating instructions with your receipt.

Panasonic Business Systems U.K.

Receipt No.

Date of purchase

Model No. Serial No.

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

103

GT15xxE.book Page 104 Wednesday, August 1, 2007 11:59 AM

Useful Information

Customer services

A customer support

A is the VoIP service provided by deltathree, Inc. for this phone. If you cannot make or receive internet calls or if you are experiencing any other issues with your

VoIP telephone services, please contact A customer support.

L

Visit www.joip.com or send an email to [email protected]

L

Call *JOIP (*5647) from your GLOBARANGE phone using the IP line.

L

For customers within the UK, call 020 7100 7403 using the landline.

For customers within the Republic of Ireland, call 01529 0157 using the landline.

In case of replacing your GLOBARANGE phone, you will need to contact A

Support Centre in order to transfer your A number and account information to the new phone.

You will not be able to use your A account on the new phone unless you contact

A Support Centre. For more information, please go to the Support section of the

Member Centre using your A number and password at www.joip.com

If you are experiencing any difficulty with your phone’s functions or features, please contact Panasonic.

Panasonic sales and support information

A is the VoIP service provided by deltathree, Inc. for this phone. If you cannot make or receive internet calls or if you are experiencing any other issues with your

VoIP telephone services, please contact A customer support. If you are experiencing any difficulty with your phone’s functions or features, please contact

Panasonic as follows.

Customer Care Centre

L

For customers within the UK: 0844 844 3898

L

For customers within the Republic of Ireland: 01289 8333

L

Visit our website for product information: www.panasonic.co.uk

L

E-mail: [email protected]

Direct Sales at Panasonic UK

L

Order accessory and consumable items for your product with ease and confidence by phoning our Customer Care Centre Monday - Thursday 9:00am - 5:30pm,

Friday 9:30am - 5:30pm (Excluding public holidays).

L

Or go on line through our Internet Accessory ordering application at

www.panasonic.co.uk

L

Most major credit and debit cards accepted.

104

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 105 Wednesday, August 1, 2007 11:59 AM

Useful Information

L

All enquiries transactions and distribution facilities are provided directly by

Panasonic UK Ltd.

L

It couldn’t be simpler!

L

Also available through our Internet is direct shopping for a wide range of finished products, take a browse on our website for further details.

Customer Care Helpline Tel. No.: U.K. 0844 844 3898 / R.O.I. 01289 8333

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

105

GT15xxE.book Page 106 Wednesday, August 1, 2007 11:59 AM

Useful Information

We recommend keeping a record of the following information for future reference.

Date of purchase

Serial No.

(found on the bottom of the base unit)

MAC address

(found on the bottom of the base unit)

Name and address of dealer

A number #

Password for the A website (www.joip.com)

*1

*1 The password is received via a A text message (page 74) after you agreed

to the Terms of Use for the A services (page 19).

Attach your purchase receipt here.

Note:

L

This equipment is designed for use on the UK and Republic of Ireland analogue telephone network.

L

In the event of problems related to:

– functions or features, you should contact your equipment supplier in the first instance.

– VoIP telephone service, you should contact A customer support (page 104).

Declaration of Conformity:

L

Panasonic Communications Co., Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio

& Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC.

Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: http://www.doc.panasonic.de

Contact:

Panasonic Services Europe a Division of Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

106

For product assistance, visit www.globarange.com

For A assistance, visit www.joip.com

GT15xxE.book Page 107 Wednesday, August 1, 2007 11:59 AM

Index

A Alarm: 55

Answering calls: 33, 36

Answering system

Erasing messages: 62, 63, 65

Listening to messages: 61, 62, 64

Turning on/off: 60, 63, 65

Auto intercom: 69, 71

Auto talk: 33

B Battery: 19, 22

Belt clip: 7, 76

C Caller ID edit: 45

Caller ID service: 44

Caller list: 45, 46

Calling code: 55

Call privacy: 34

Call screening: 60, 67

Call share: 34, 38

Call Waiting: 34, 37

Call Waiting Caller ID: 44

Cancelling: 77

Chain dial: 41

Character entry: 79

CID (Caller ID): 44

Conference calls: 35, 38, 69, 71

Connections: 18

Customer support: 52

D Date and time: 29

Default gateway: 30

Deregistration: 77

DHCP: 30

Dial lock: 57

Direct commands: 51, 52, 53, 54

Display

Contrast: 51

Language: 29

DNS: 31

E Emergency calls: 5

Emergency numbers: 40

Error messages: 81

G Greeting message: 61

H Handset LCD backlight: 33

Handset name: 56

Index

Headset, optional: 9

Hold: 33, 37

I

Intercom: 69, 70

Internet calls: 32, 36, 39

Internet connection settings: 30

Interrupt tone: 51

IP address: 30

IP indicator: 23

J joip: 4

joip MSG alert: 75

joip number: 4, 31

joip service menu: 75

joip Terms of Use: 19

joip text message: 74

Joystick: 17

K Keytones: 52

L Landline calls: 32, 36

Light-up ID: 45

Line selection: 29

M Making calls: 32, 36, 39

MEMO: 63

Memory capacity (message

recording): 60

Message alert: 66, 68, 74

Missed calls: 44

Mobile phone: 39

Mute: 34, 37, 70, 71

My joip numbers: 31

N Network settings: 30

Night mode: 52, 58

Number of rings: 66

P Page: 14, 71

Pause: 33, 43

Phonebook: 40

Phonebook copy: 42

Phonebook import: 73

PIN

Base unit: 51, 56

Power failure: 20

R Recall: 34, 37

Recall time: 57

Recording time: 66

Redial list: 32

Registration: 77

Remote code: 64

107

GT15xxE.book Page 108 Wednesday, August 1, 2007 11:59 AM

Index

Remote operation: 64

Reset button: 78

Ring colour: 52

Ringer ID: 45

Ringer off: 33, 52, 59

Ringtone: 54, 59

Ringtone import: 73

Room monitor: 69, 71

S Service menu: 75

Soft keys: 17

Software update: 57

Speakerphone: 32, 36

Speed dialler: 43

Status indicator: 23, 86

Subnet mask: 30

System requirements: 7

T TEL indicator: 23

Time adjustment: 53

Toll saver: 66

Transferring calls: 69, 71

Troubleshooting: 84

V Voice guidance: 64

Voice Mail: 68

Volume

Base unit ringer: 59

Base unit speaker: 36

Handset receiver: 32

Handset ringer: 52

Handset speaker: 32

108

GT15xxE.book Page 109 Wednesday, August 1, 2007 11:59 AM

Notes

109

GT15xxE.book Page 110 Wednesday, August 1, 2007 11:59 AM

Notes

110

GT15xxE.book Page 111 Wednesday, August 1, 2007 11:59 AM

Notes

111

GT15xxE.book Page 112 Wednesday, August 1, 2007 11:59 AM

1999/5/EC

Sales Department:

Panasonic Business Systems U.K.

Panasonic House, Willoughby Road, Bracknell, Berkshire, RG12 8FP

Panasonic Communications Co., Ltd.

1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan

Copyright:

This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd.

© 2007 Panasonic Communications Co., Ltd. All Rights Reserved.

PQQX15942YA

CM0507SH2087

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents