Yamaha RX-V567 User manual

English
Quick Reference Guide
■ Accessories
The following accessories are supplied with this product.
PUSH
Remote control
Batteries (2) (AAA, R03, UM-4)
AM loop antenna
3
2
VIDEO AUX input cover
YPAO microphone
* The configuration of the supplied FM antenna will differ depending on
the country or region where the unit is being used.
Preparing the remote control
1
Indoor FM antenna*
1
Take off the battery compartment cover.
2
Insert the two supplied AAA batteries
into the battery case, following the
polarity markings.
3
Snap the battery compartment cover
back into place.
Be sure to aim the remote control directly at the
remote control sensor on this unit during operation.
within 6 m
(20 ft)
■ Items necessary for connection
Speakers
Ex.
Front speaker
Ex.
Ex.
Ex.
Center speaker
Surround speaker and
Surround back speaker
Active subwoofer
• Use speakers with an impedance of at least 6 Ω.
• If you are using a CRT monitor, we recommend that you use magnetically shielded speakers.
• Prepare at least two speakers (for front). The priority of the other speakers is as follows:
1 Two surround speakers
2 One center speaker
3 One (or two) surround back speaker (s)
Cable
External components
• Cables for connecting external components
(may differ depending on the components you are connecting)
• Speaker cables
(a quantity to match the number of speakers you are connecting)
• Audio pin cable
(for subwoofer)
TV
Playback device such as BD
(Blu-ray Disc)/DVD players
-1-
Some features are not available in certain regions.
Connect and install as follows the first time you use this unit.
See the following explanations for the connections for each number.
TV
7.1 Connect when using with 7.1-channel
3
speaker layout. Place the surround back
speakers (L/R) 30 cm or more away from
each other.
2
6.1 Connect when using with 6.1-channel
speaker layout. Place the surround back
speaker behind the listening position.
BD/DVD player
(recorder)
4
This unit
Front
speaker R
Front
speaker L
Subwoofer
Surround
speaker R
1
Center speaker
1
Surround
speaker L
7.1
7.1
Surround back
speaker L
Surround back
speaker R
6.1
Surround back
speaker
1 Connect the speakers
2 Connect a TV
3 Connect playback device such as BD/DVD players and recorders
4 Set the VOLTAGE SELECTOR and connect the AC power cable
(Asia and General models)
Connect the AC power cable
(Other models)
When connection and installation is finished, set up the speaker parameters
automatically 5 .
-2-
1 Connect the speakers
Front speaker
R
L
Surround
speaker
R
L
Surround back
speaker
R
L
7.1
7.1 Connect when using with 7.1-channel speaker layout.
6.1 Connect when using with 6.1-channel speaker layout.
7.1
6.1
Caution:
• Remove the AC power cable of this unit from the power outlet
before connecting the speakers.
• Generally speaker cables consist of two parallel insulated
cables. One of these cables is a different color, or has a
line running along it, to indicate different polarity. Insert the
different colored (or lined) cable into the “+” (positive, red)
terminal on this unit and the speakers, and the other cable into
the “-” (minus, black) terminal.
• Be careful that the core of the speaker cable does not touch
anything or come into contact with the metal areas of this
unit. This may damage this unit or the speakers. If the speaker
cables short circuit, “CHECK SP WIRES!” will appear on the
front panel display when this unit is switched on.
• (U.S.A. and Canada models only) When connecting 6 Ω
speakers, set the speaker impedance to 6 Ω on this unit before
making connections. Refer to Owner’s Manual for information
on settings.
SPEAKERS
HDMI 3
HDMI 4
FRONT
CENTER
SURROUND
SURROUND BACK/
BI-AMP
SINGLE
SUBWOOFER
AUDIO
OUT
PRE OUT
This unit can connect speakers that support Bi-amp connection for
front speakers. Refer to “Owner’s Manual” for the details.
Center speaker
Subwoofer
Connecting speakers
2
FR
ON
3
Connecting the banana plug
(Except U.K., Europe, Asia and Korea
models)
T
1
4
1
Tighten the knob, and then insert the banana plug
into the end of the terminal.
Remove approximately 10 mm of insulation from
the ends of the speaker cables, and twist the bare
wires of the cables together firmly so that they will
not cause short circuits.
2
Loosen the speaker terminals.
3
Insert the bare wire of the speaker cable into the
gap on the side of the terminal.
4
Tighten the terminal.
FR
ON
T
Banana plug
Connecting the subwoofer
1
2
Connect the subwoofer input jack to the SUBWOOFER
jack on this unit with an audio pin cable.
Set the subwoofer volume as follows.
Volume: Set to approximately half volume (or slightly less than
half).
Crossover frequency (if available): Set to maximum.
VOLUME
MIN
MAX
CROSSOVER/
HIGH CUT
MIN
MAX
Subwoofer examples
-3-
2 Connect a TV
If your TV has multiple inputs, connect with the following priority (A to C).
(Ex.: U.K. and Europe models)
HDMI
HDMI
HDMI 1
ANTENNA
HDMI 2
compatible TV.
GND AM
PR
PR
PR
PB
PB
Y
Y
COMPONENT
VIDEO
S VIDEO
75ǡ
PB
A When using an HDMI
HD
COMPONENT
VIDEO
COMPONENT
VIDEO
FM
HDMI
(BD/DVD)
HDMI OUT
DOCK
PR
VIDEO
VIDEO
Y
B When using a component
PB
V
Y
V
MONITOR OUT
video input-compatible TV.
VIDEO
V
OPTICAL
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
A 1
AV
AV
A 2
A 3
AV
A 4
AV
A 5
AV
A 6
AV
A
AV
OUT
AUDIO 1
AUDIO 2
VIDEO
V
C When using a TV compatible
with video input only.
Video input to this unit is output to a TV using output jacks of the
same kind.
When connecting to a HDMI compatible TV
Video signal such as component video and video received by this
unit is converted to HDMI and output to the TV. Just select HDMI
input on the TV to view video from any external source connected
to this unit.
You can change the resolution and aspect ratio used when
converting to HDMI to suit your requirements.
✽ Only U.K. and Europe models are equipped with the S VIDEO jacks. The
video signals input from the S VIDEO jack are output only from HDMI.
Input
Output
HDMI
HDMI
COMPONENT
VIDEO
COMPONENT
VIDEO
HDMI input
S VIDEO
VIDEO
Component
video input
VIDEO
Video input
Through
When connecting to a non-HDMI compatible TV
Connect to the TV using the same type of connection that you
used to connect to the playback device, and change the inputs
on your TV to match that of the playback device you are using for
playback.
Converted
Listening to TV audio
To playback TV audio on this unit, connect the TV audio output to this
unit.
When using an HDMI compatible TV that supports Audio
Return Channel functions and / or HDMI Control functions (Ex.
Panasonic VIERA Link), you can enjoy the TV sound on this unit
as follows:
Connect the following input jacks, matching the audio output jacks on
your TV. When viewing your TV, select the appropriate input source on
this unit.
OPTICAL
When using a TV that supports the Audio Return
Channel functions and HDMI Control functions
The audio / video output from the unit to the TV and audio
output from the TV to the unit are possible using a single HDMI
cable.
The input source is switched automatically to match operations
carried out on the TV, and that makes TV sound control easier
to use.
For the connections and settings, refer to “Using the HDMI
Control function” in Owner’s Manual.
DOCK
O
COMPONENT
VIDEO
Audio
output
PR
PB
VIDEO
Y
O
OPTICAL
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
AV 1
AV 2
AV 3
AV 4
AV 5
When using a TV that supports HDMI Control functions
Audio output from TV
Input jack on this unit
Optical digital output
AV1 or AV4
Coaxial digital output
AV2 or AV3
Analog output
One of AV5, AV6, AUDIO1,
AUDIO2, and V-AUX
HDMI Audio Return Channel
(Described in the right column)
HDMI OUT
When HDMI Control functions are enabled on the unit, input
source can be switched automatically to match operations
carried out on the TV.
For the connections and settings, refer to “Using the HDMI
Control function” in Owner’s Manual.
✽ Connecting to AV4 allows you to playback TV audio just by pressing
the “TV” under “SCENE” key.
-4-
3 Connect playback device such as BD/DVD players and recorders
If your playback device has multiple audio/video outputs, connect with the following
priority (A to D) to enjoy a higher quality sounds and images.
A When playback device is capable
HDMI
HDMI
of HDMI output
(Ex.: U.K. and Europe models)
HDMI
COMPONENT
VIDEO
PR
B When playback device is capable
of component video output (with
optical digital audio output)
ARC
PB
(BD/DVD)
HDMI OUT
DOCK
HDMI 1
ANTENNA
Y
FM
PR
OPTICAL
PR
O
S VIDEO
PB
PB
Y
Y
75ǡ
PB
PB
VIDEO
VIDEO
V
Y
Y
COMPONENT
VIDEO
C When playback device is capable
of component video output (with
coaxial digital audio output)
HDMI 3
GND AM
PR
PR
HDMI 2
COMPONENT
C
OMPONENT
VIDEO
COMPONENT
VIDEO
MONITOR OUT
PR
L
PB
R
O
Y
COAXIAL
C
OPTICAL
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
AV 1
AV 2
A 3
AV
A 4
AV
AV 5
A 6
AV
A
AV
OUT
AUDIO 1
AUDIO 2
C
VIDEO
D When playback device is capable
of video output (with analog
audio output) only
V
AUDIO
L
R
•
•
•
•
When playback, select the corresponding input source to which the jack is connected.
Connecting to HDMI1 allows you to select the HDMI input just by pressing the “BD/DVD” under “SCENE” key.
Connecting to AV3 allows you to select the AV3 input just by pressing the “CD” under “SCENE” key.
If necessary, you can connect components that cannot be connected using the above methods, such as devices that output video from
component video output jacks and audio from analog output jacks. Refer to Owner's Manual for details.
• Only U.K. and Europe models are equipped with the S VIDEO jacks. The video signals input from the S VIDEO jack are output only from
HDMI.
Set the VOLTAGE SELECTOR and connect the AC power cable
4
(Asia and General models)
Connect the AC power cable
(Other models)
(Asia and General models only)
Select the switch position according to your local voltage
using a straight slot screwdriver.
(General model)
Voltages are AC 110/120/220/230-240 V, 50/60 Hz.
VOLTAGE SELECTOR
VOLTAGE
SELECTOR
(Asia model)
Voltages are AC 220/230-240 V, 50/60 Hz.
To the power
outlet
AC power cable
Caution
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local voltage BEFORE plugging the
power cable into the AC wall outlet. Improper setting of
the VOLTAGE SELECTOR may cause damage to this
unit and create a potential fire hazard.
-5-
5 Set up the speaker parameters automatically (YPAO)
When connection is finished, adjust the status, sizes, and volume balance of the
speakers to provide an optimal sound field. This unit is equipped with a YPAO
(Yamaha Parametric Room Acoustic Optimizer) function that adjusts the speaker
balance automatically with a simple procedure.
When you use YPAO, a test tone will be output from the speakers for approximately 3 minutes and acoustic measuring will be performed.
When using YPAO, be careful of the following.
• The test tone is output at high volume. Please refrain from using this function at night when it may be a nuisance to others nearby.
• Please take care that the test tone does not frighten any small children.
When operating the YPAO, information is displayed both on the TV screen (On-Screen Display) and on the front panel. This explanation will use
operations while viewing the display on the TV screen.
1
Check the following before using YPAO.
This unit
CROSSOVER/
HIGH CUT
VOLUME
• The headphones are removed.
TV
• This unit is connected to the TV correctly.
• The power is turned on.
• The video input to which the video output from this unit has been selected.
MIN
MAX
MIN
MAX
Subwoofer examples
Subwoofer
• The power is turned on.
• Volume is set to approximately half, and the cross-over frequency (if present)
is set to maximum.
2
Place the supplied YPAO microphone at ear height in your listening position.
YPAO microphone
When positioning the microphone, we recommend that you use
equipment that allows you to adjust the height (such as a tripod) as a
microphone stand. When using a tripod, use the tripod screws to fix
the microphone in place.
3
Press RECEIVER A on the remote control to switch this unit on.
4
Connect the YPAO microphone to the YPAO MIC jack on the front panel.
“MIC ON. View OSD MENU” appears
on the front panel display, and then
appears the following display on the TV
screen.
YPAO MIC
INFO
bbAutobSetup
bbbbEQbType;;;;Natural
bb.bStart
bbb[OPTION]:EQbSelect
bbbb[SETUP]:Start
YPAO microphone
Continues to
the next page
-6-
This completes preparations. To achieve more accurate results, be careful of the following when
measuring.
• Measuring will take approximately 3 minutes. Keep the room as quiet as possible during
measurement.
• Wait in the corner of the listening room during measurement or leave it entirely, to avoid
becoming an obstruction between the speakers and the YPAO microphone.
CODE SET
TRANSMIT
SOURCE
RECEIVER
SLEEP
RECEIVER A
HDMI
1
2
3
4
1
2
3
4
5
6
1
2
V-AUX
V
VAUX
[ A ]
[ B ]
DOCK
PRESET
TUNING
A
AV
5
Press SETUP on the remote control to start measurement.
AUDIO
bbAutobSetup
bb
bbbb;Initializing
bb.b;PrebCheck
bbbb;MainbCheck
bbbbbbbbbbbbbbbbbbbbb
bbbb;Calculation
bbbb;Level
TUNER
FM
AM
INFO
MEMORY
ENHANCER SUR. DECODE
MOVIE
MUSIC
STEREO
STRAIGHT
bbbbCheckbCHb=bFrontbL
bbbb;;;;;;;;;;;;;;;02%
bbbbbb[b]bbb:Exitb
DIRECT
SCENE
[
BD
DVD
TV
CD
SETUP
RADIO
SETUP
VOLUME
ENTER
OPTION
The following display appears if measurement finishes without any problems.
ENTER
SP
bbAutobSetup
RETURN
Displays the number of speakers connected to this
unit in the following order:
Total of Front and Center/Total of Surround and
Surround Back/Subwoofer
bbbbResult
bbbbbSPbb:bbbbb3/4/0.1
bbbbbbbbbbbbbbbbbbbbb
bbbbbDIST:bb2.50/b3.00m
bbbbbbbbbbbbbbbbbbbbb
bbbbbLVLb:b-1.0/b+1.5dB
bb.bb>SetbbbbCancel
bbbb[p]/[[]:Select
bbbb[ENTER]:Finish
DIST
Displays the speaker distance from the listening
position in the following order:
Closest speaker distance/Farthest speaker distance
DISPLAY
A
POP-UP
MENU
TOP
MENU
MUTE
REC
1
2
3
5
6
7
9
0
10
4
8
ENT
TV
INPUT
TV VOL
TV CH
MUTE
LVL
Displays the speaker output levels in the following order:
Lowest speaker output level/Highest speaker output
level
Note
When a problem occurs, an error message or a warning
message appears either during or after measurement. Refer
to “Set up the speaker parameters automatically (YPAO)” in
Owner’s Manual to solve the problem, and carry out YPAO again.
6
Press ENTER on the remote control to apply the results
of measurement.
Auto Setup
You can use the following functions with this
unit. For details on the operations, refer to
Owner’s Manual on the supplied CD-ROM.
■ Various parameter adjustment to match your
listening environment
- Sound quality control with the equalizer
<Graphic Equalizer>
- Easy listening at low volumes <Adaptive DRC>
- Adjusting volume between input sources
<Volume Trim>
AUTO SETUP Finished
■ External device connection and playback
Disconnect Microphone
- Connections and playback from BD/DVD players
(recorders), TV audio, and other devices
- Playback from an iPod/iPhone
- Playback from a Bluetooth device
PRESS [ENTER]
[SETUP]:Exit
7
Remove the YPAO microphone.
■ FM/AM tuner
YPAO finishes automatically when the YPAO
microphone is removed.
YPAO MIC
INFO
- Simple preset tuning
- (U.K. and Europe models)
Radio Data System tuning
- (U.K. and Europe models)
Automatic traffic information reception
- (Asia and General models only)
Changing FM/AM frequency steps initializing various
settings for this unit
etc.
-7-
Operation guide
②
①
③
⑥
YPAO MIC
④
DIRECT
INFO
MEMORY
PRESET
FM
AM
TUNING
VOLUME
SCENE
BD
DVD
PHONES
INPUT
TV
TONE CONTROL
CD
PROGRAM
RADIO
VIDEO AUX
STRAIGHT
SILENT CINEMA
PORTABLE
⑦
VIDEO
L
AUDIO
R
③
1 Switches this unit between on and standby mode
①
This unit switches between on and standby mode every time you press this key.
2 Choose an input source to listen to
CODE SET
TRANSMIT
The name of the selected input source appears on the front panel display.
SOURCE
RECEIVER
SLEEP
VOL.
HDMI1
L
SL
SBL
SW
C
HDMI
R
SR
SBR
1
2
3
4
3
4
AV
1
3 Select sound field programs and sound decoders
Front
panel
Remote
control
②
AUDIO
Description
5
6
1
2
V-AUX
[ A ]
[ B ]
DOCK
PRESET
TUNING
TUNER
MOVIE
Selects sound field programs optimized for viewing movies,
dramas, and sports.
MUSIC
Selects sound field programs optimized for appreciating music.
PROGRAM
STEREO
SUR. DECODE
FM
AM
INFO
MEMORY
MOVIE
MUSIC
ENHANCER SUR. DECODE
Selects settings for stereo playback or enhancers for
compressed audio.
ENHANCER
BD
DVD
DIRECT
TV
CD
SETUP
RETURN
⑥
RADIO
VOLUME
④
MUTE
⑤
DISPLAY
POP-UP
MENU
TOP
MENU
The current volume level is displayed on the front panel display.
③
OPTION
ENTER
Switches to direct mode for faithful reproduction of audio.
4 Adjusts the volume level
DIRECT
SCENE
Switches to straight decoding mode for stereo/multi-channel
playback without using a sound field program.
STRAIGHT
STEREO
STRAIGHT
Selects surround decoders such as Dolby Pro Logic II.
STRAIGHT
DIRECT
2
REC
VOL.
Volume -18.5dB
L
SL
SBL
SW
C
R
SR
SBR
5 Mutes the sound
The indicator blinks while the sound is muted.
1
2
3
4
5
6
7
8
9
0
10
ENT
TV
INPUT
6 Switches between input settings
TV VOL
TV CH
MUTE
You can switch input sources and sound field programs with a single key.
SCENE
BD/DVD
TV
CD
RADIO
Input
HDMI 1
AV4
AV3
TUNER
Sound field program
Straight
Straight
Straight
7ch Enhancer
- Pressing and holding this key allows you to store input sources/sound field programs.
- Press this key when this unit is in standby mode to switch on the unit.
7 Adjusting high/low-frequency sound (Tone control)
1
Press TONE CONTROL to select “Treble” or “Bass.”
TONE
Treble
2
VOL.
0.0dB
SW
C
R
L
SL
SR
SBL
SBR
Press PROGRAM l / h to adjust the output level in those
frequency ranges.
- You can set the tone control for speakers and headphones separately. Connect the
headphones when adjusting the headphone tone control.
- If you set an extreme tone balance, sounds may not match those from other channels.
©2010 Yamaha Corporation
-8-
YC506B0/QREN