Sony DSC-P200 P200 camera SERVICE MANUAL

SERVICE MANUAL

Ver 1.2 2005.05

Photo: Silver

DSC-P200

LEVEL

2

US Model

Canadian Model

AEP Model

UK Model

E Model

Hong Kong Model

Australian Model

Chinese Model

Korea Model

Argentine Model

Brazilian Model

Tourist Model

Japanese Model

• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-854-51).

• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (9-876-854-41).

• Reference No. search on printed wiring boards is available.

• Note in Lens Frame Installation

• Exchange Method of Barrier Assy

On the CH-146, SY-123 boards

This service manual procides the information that is premised the circuit board replacement service and not intended repair inside the

CH-146, SY-123 boards.

Therefore, schematic diagram, printed wiring board and electrical parts list of the CH-146, SY-123 boards are not shown.

The following pages are not shown.

Schematic diagrams .................. Pages 4-9 to 4-28

Printed wiring boards ................ Pages 4-39 to 4-42

Waveforms ................................ Pages 4-45 and 4-46

Mounted parts location .............. Page 4-48 and 49

Electrical parts list ..................... Pages 5-7 to 5-11

The above-described information is shown in service manual Level 3.

DIGITAL STILL CAMERA

DSC-P200

9-876-854-31

Sony EMCS Co.

2005E0500-1

© 2005.5

Published by DI Technical Support Section

Camera

[System]

Image device 9.11 mm (1/1.8 type) color

CCD, Primary color filter

Total pixel number of camera

Approx. 7 410 000 pixels

Effective pixel number of camera

Approx. 7 201 000 pixels

Lens Carl Zeiss Vario-Tessar

3× zoom lens f = 7.9 - 23.7 mm (38 - 114 mm when converted to a 35 mm still camera)

F2.8 - 5.2

Exposure control Automatic exposure, Manual exposure, Scene Selection (9 modes)

White balance Automatic, Daylight, Cloudy,

Fluorescent, Incandescent,

Flash, One push

File format (DCF compliant)

Still images: Exif Ver. 2.2

JPEG compliant, DPOF compatible

Movies: MPEG1 compliant

(Monaural)

Recording media “Memory Stick”

Flash Recommended distance (ISO set to Auto): 0.2 m to 3.5 m

(7 7/8 inches to 11 feet 5 3/4 inches) (W)/0.3 m to 2.5 m

(11 7/8 inches to 8 feet 2 3/8 inches) (T)

[Input and Output connectors]

Multi connector

USB communication

Hi-Speed USB (USB 2.0 compliant)

[LCD screen]

LCD panel 5.1 cm (2.0 type) TFT drive

Total number of dots

134 000 (560×240) dots

SPECIFICATIONS

[Power, general]

Battery pack used

NP-FR1

Power requirements

3.6 V

Power consumption

(during shooting with the LCD screen on)

1.2 W

Operating temperature

0°C to +40°C (+32°F to

+104°F)

Storage temperature

–20°C to +60°C (–4°F to

+140°F)

Dimensions

Mass

Microphone

104.5×51.5×27.9 mm

(4 1/8×2 1/8×1 1/8 inches)

(W/H/D, excluding maximum protrusions)

Approx. 180 g (6.3 oz)

(including NP-FR1 battery pack, “Memory Stick”, and wrist strap)

Electret condenser microphone

Speaker

Exif Print

Dynamic speaker

Compatible

PRINT Image Matching II

Compatible

PictBridge Compatible

AC-LS5/LS5B AC Adaptor

Input rating

Output rating

100 V to 240 V AC, 50/60 Hz,

11 W

4.2 V DC*

* See the label on the AC

Adaptor for other specifications.

Operating temperature

0°C to +40°C (+32°F to

+104°F)

Storage temperature

–20°C to +60°C (–4°F to

+140°F)

Dimensions

Mass

Approx. 48×29×81 mm

(1 15/16×1 3/16×3 1/4 inches)

(W/H/D, excluding projecting parts)

Approx. 130 g (5 oz) excluding power cord (mains lead)

NP-FR1 battery pack

Battery used Lithium-ion battery

Maximum voltage

DC 4.2 V

Nominal voltage DC 3.6 V

Capacity 4.4 Wh (1 220 mAh)

Design and specifications are subject to change without notice.

DSC-P200

— 2 —

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK

0

OR DOTTED LINE WITH

MARK

0

ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE

0

SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1.

Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.

2.

Check the interboard wiring to ensure that no wires are

"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

DSC-P200

Unleaded solder

Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40

°

C higher than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to about 350

°

C.

Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

— 3 —

Section

TABLE OF CONTENTS

Title Page

1.

SERVICE NOTE

1-1.

Note for Repair ································································ 1-1

1-2.

Discharging of the FP-163 Flexible Board’s Charging

Capacitor (C601) ····························································· 1-1

1-3.

Note in Lens Frame Installation ······································ 1-2

1-4.

Description on Self-diagnosis Display ···························· 1-2

2.

DISASSEMBLY

2-1.

Disassembly ····································································· 2-1

2-2.

SY-123 Board Service Position ······································· 2-5

2-3.

Exchange Method of Barrier Assy ·································· 2-7

2-3-1. Peel Off Old Ornamental Ring A ···································· 2-7

2-3-2. Remove Old Barrier Assy ················································ 2-8

2-3-3. Install New Barrier Assy ················································· 2-8

2-3-4. Adhere the Ornamental Ring A ······································· 2-9

2-4.

Circuit Boards Location ················································ 2-10

3.

BLOCK DIAGRAMS

3-1.

Overall Block Diagram (1/2) ··········································· 3-1

3-2.

Overall Block Diagram (2/2) ··········································· 3-3

3-3.

Power Block Diagram (1/2) ············································· 3-5

3-4.

Power Block Diagram (2/2) ············································· 3-7

4.

PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS

4-1.

Frame Schematic Diagram ·············································· 4-1

4-2.

Schematic Diagrams ························································ 4-5

CD-517 FLEXIBLE (CCD IMAGER) ···························· 4-7

FP-162 FLEXIBLE

(DC IN, MULTI CONNECTOR) ·································· 4-29

FP-163 FLEXIBLE (FLASH) ······································· 4-30

MEMORY STICK CONNECTOR

(FP-161 FLEXIBLE) ····················································· 4-30

CONTROL SWITCH BLOCK (SW51740), (RL) ········ 4-31

4-3.

Printed Wiring Boards ··················································· 4-35

CD-517 FLEXIBLE ······················································ 4-37

FP-162 FLEXIBLE ······················································· 4-43

FP-163 FLEXIBLE ······················································· 4-44

4-5.

Mounted Parts Location ················································ 4-47

5.

REPAIR PARTS LIST

5-1.

Exploded Views ······························································· 5-2

5-1-1. Overall Assembly ···························································· 5-2

5-1-2. Lens Block Assembly ······················································ 5-3

5-1-3. Main Block Assembly ····················································· 5-4

5-1-4. BT Block Assembly ························································· 5-5

5-2.

Electrical Parts List ························································· 5-6

DSC-P200

— 4 —

1. SERVICE NOTE

1-1. NOTE FOR REPAIR

Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

When remove a connector, don’t pull at wire of connector.

It is possible that a wire is snapped.

When installing a connector, don’t press down at wire of connector.

It is possible that a wire is snapped.

Cut and remove the part of gilt which comes off at the point.

(Be careful or some pieces of gilt may be left inside)

1-2. DISCHARGING OF THE FP-163

FLEXIBLE BOARD’S CHARGING

CAPACITOR (C601)

The charging capacitor (C601) of the FP-163 flexible board is charged up to the maximum 300 V potential.

There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below.

Preparing the Short Jig

To preparing the short jig, a small clip is attached to each end of a resistor of 1 k

Ω

/1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to prevent electrical shock.

1 k

Ω

/1 W

Discharging the Capacitor

Short-circuit between the positive and the negative terminals of charged capacitor with the short jig about 10 seconds.

R:1 k

Ω

/1 W

(Part code:

1-215-869-11)

FP-163 flexible board

CN757

Wrap insulating tape.

DSC-P200

1-1

1-3. NOTE IN LENS FRAME INSTALLATION

When tightening a screw, have both sides of the lens block assembly so as not for the load to depend.

Lens frame

P2 tapping screw

Lens block assembly

1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY

Self-diagnosis display

• C: ss: ss

You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.)

• E: ss: ss

Contact your Sony dealer or local authorized Sony service facility.

Display Code

C:32:ss

C:13:ss

E:61:ss

E:91:ss

Countermeasure

Turn the power off and on again.

Format the “Memory stick”.

Insert a new “Memory Stick”.

Checking of lens drive circuit.

Checking of flash unit or replacement of flash unit.

Cause

Trouble with hardware.

Unformatted memory stick is inserted.

Memory stick is broken.

When failed in the focus and zoom initialization.

Abnormality when flash is being charged.

Caution Display During Error

SYSTEM ERROR

FORMAT ERROR

MEMORY STICK ERROR

—

DSC-P200

1-2E

2. DISASSEMBLY

The following flow chart shows the disassembly procedure.

2-1. DISASSEMBLY

Note: High-voltage cautions

Discharging the Capacitor

Short-circuit between the two points with the short jig about 10 seconds.

CN757

R:1 k

Ω

/1 W

(Part code:

1-215-869-11)


4

2

3

4

6

1

4

1

Screw (M1.4) x1

2

Claw x6

3

Side cabinet assembly

4

Screw (M1.4) x8

5

Cabinet plate x1

6

Cabinet front block

7

Cabinet (rear) block assembly

2

7

4

5

DSC-P200

1

2

3

1

Ornamental ring (A)

2

Tapping screw x2

3

Barrier assy

Note: When you exchange rings, be sure to follow the procedure carried on

"2-3. Exchange Method of Barrier

Assy" (2-7 page).

2-1

3

4

1

2

3

1

Connector x2 : CN101, CN202

2

Connector x1 : CN758

3

Claw x2

4

Flexible board x1 : CN754

5

Lens block

5

to Page 2-3

2-2

from Page 2-2

1

3

4

3

2

1

Connector x1: CN707

2

Connector x1: CN003

3

Claw x2

4

Control switch block

2

5

3

8

7

4

1

6

1

Flexible board x1: CN704

2

P2 tapping screw x1

3

Claw x1

4

P2 tapping screw (M1.7) x1

5

Claw x1

6

Connector x2: CN751, 756

7

Control SW block (SW51740)

8

SY-123 board

DSC-P200

1

1

1

Claw x3

2

D901, LCD901

2

2-3 2-4

4

1

2

3

1

P2 tapping screw x1

2

Multi fixed plate x1

3


4

Memory stick connector

2-2. SY-123 BOARD SERVICE POSITION

DSC-P200

4

6

2

3

4

1

2

7

4

5

4

1

1

3

4

5

2

3

1

2

2-5

4

1

2

3

8

4

1

5

3

6

4

1

3 3

2

7

2


AC power adaptor


AC IN


SY-123 board

Control SW block

(SW51740)

A/V multi cable

Color monitor

Memory stick connector

(including FP-161 flexible board)

Lens block

D901, LCD901

2-6

2-3. EXCHANGE METHOD OF BARRIER ASSY

Service parts

1

2

3

Part Number

3-091-427-01

X-3954-476-1

3-086-156-31

Part Name

Ring (A), Ornamental

Barrier Assy

Tapping screw (P2)

Quantity

1

1

2

Tools used

Torque driver

Soldering iron

Weight about 60g

Adhesive (Super X) (Note)

Note:

Use adhesive (Super X) or an equivalent article.

Don’t use what becomes white after drying like a quick-drying glue.

1

2

3

2-3-2. REMOVE OLD BARRIER ASSY

1

Remove two screws.

* Discard the removed screws.

2

Remove the Barrier Assy.

* Discard the removed Barrier Assy.

1

1

2

2-3-1. PEEL OFF OLD ORNAMENTAL RING A

The Ornamental Ring A has adhered to the Barrier Assy strongly and accordingly, use a soldering iron to weaken the adhesive force.

Heat four circled portions with the soldering iron.

Heating temperature is about 300ºC.

Beware of a burn since the entire Ornamental Ring becomes hot.

*

As the adhesive force of Ornamental Ring A is considerably large, the forced peeling will damage the group-1 frame.

Insert the tip of tweezers, etc. into a notch of the group-1 frame and prize the ring.

* Take extreme care so as not to damage the coated surface of the group-1 frame.

In case of difficult peeling, heat the ring again with the soldering iron.

If this re-heating failed, it may be advisable that the ring be peeled while heating the portions 1

→

2

→

3

→

4 in the under figure one by one sequentially.

* Discard the removed Ornamental Ring A.

*

After removing the Barrier Assy, if the “G1 Dust-Proof Ring” was removed, it must be returned to the home position.

In returning the ring, adjust the location of a projection to the lens direction.

This is an important part to prevent the dust and light from coming in.

* After removing the Barrier Assy, take extreme care not to drop dust or foreign substances in the lens barrel.

2-3-3. INSTALL NEW BARRIER ASSY

1

Install new Barrier Assy by paying attention to the projection of the Barrier Assy in relation to the position shown in the under figure.

2

Tighten two screws.

*

Tightening torque = 0.5 kgf (4.9 N)

Tip

2

4

1

3

1

Projection

2

2

DSC-P200

2-7 2-8

2-3-4. ADHERE THE ORNAMENTAL RING A

Apply an adhesive to four recesses on the top surface of the Barrier Assy.

* Do not apply too much adhesive. (Make quantity of adhesives into the quantity in which a groove hides.)

Meeting a “notch” of the Ornamental Ring A with a “projection” of the group-1 frame, push the Ornamental Ring A into the group-1 frame.

* The projection of the spring for preventing static electricity must be tilted.

Put the 60g weight on the Ornamental Ring A so that the Ornamental Ring A does not float up until the adhesive hardens.

Note:

Be careful not to give a shock.

*

After the weight was put, no gap must be present in full circumference between Ornamental Ring A and group-1 frame.

A gap, if present, causes the crackle sound NG.

* The weight must push in the Ornamental Ring A only.

If the weight is put on the mold part of the Barrier Assy, the Ornamental Ring A will float up.

Notch

Adhesive

Projection

Adhesive

Adhesive

Adhesive

Do not put the weight on a black mold part.

Not gap in full circumference.

Completion after 30 minutes.

DSC-P200

2-9

2-4. CIRCUIT BOARDS LOCATION


SY-123

(including CP101

(CH-146 board) and IC301

(KFW board))

Control SW block

(SW51740)

FP-163 flexible

CD-517 flexible

FP-162 flexible

CH-146

(included in SY-123)

FP-161 flexible

(included in Memory stick connector)

Board Name Function

CD-517 flexible

CH-146

CCD IMAGER

CCD SIGNAL PROCESS

(included in SY-123)

FP-161 flexible

(included in Memory

MEMORY STICK CONNECTOR stick connector)

FP-162 flexible

FP-163 flexible

SY-123

DC IN, MULTI CONNECTOR

FLASH

CAMERA MODULE, CAMERA DSP, LENS DRIVE,

(including CP-101 SH DSP, FRONT CONTROL, LCD DRIVE, AUDIO,

( CH-146 board) and DC/DC CONVERTER, CONNECTOR

IC301 (KWF board))

DSC-P200

2-10E

DSC-P200

3. BLOCK DIAGRAMS

3. BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/2)

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

LENS

LENS BLOCK

SHUTTER

MOTOR

M

ZOOM

MOTOR

M

ZOOM

FG

ZOOM

SENSOR

FOCUS

SENSOR

FOCUS

MOTOR

M M

IRIS

MOTOR

LENS TEMP

SENSOR

A

: VIDEO SIGNAL

A

: AUDIO SIGNAL

A : VIDEO/AUDIO SIGNAL

FLASH

UNIT

C601

CHARGING

CAPACITOR

+

IRIS

(METER)

FP-163 FLEXIBLE

BOARD

XE_H

TRIG 300V

XE_L

CL501

CL502

CD-517 FLEXIBLE BOARD (1/2) SY-123 BOARD (1/2)

17

19

IC101

CCD

IMAGER

23

25

24

28

29

Q102

Q103

BUFFER

Q101

RG, H1B, H2B

H1A, H2A

16

CN101

(1/2)

CCD OUT

13

4

10

7

9

6

PWR SAVE

3

5

26

1

6

7

4

8 ı

15

27

V2, V4, V5A, V5B,

V6, V7, V8, V9, V10

34

30 ı

23

V1, V3A, V3B

VST

VHLD

VSUB

36

32

33

35

31

21

VSUB CONT

22

Q105

Q108

6

37

1

3

20

15 ı

18

9

12 ı

14

7

11

10

8

19

21

5

2

4

36

CH-146 BOARD

10

20

17

13

11

19

135

86

134 136 2 4

6 9 12 15

18 21 24

27 30 32

133

49 105

66 101 120

99

33

42

51

37

48

IC101

CCD SIGNAL

PROCESSOR,

TIMING

GENERATOR

113 109

112 115

7 125

119 118

121

132

124

3 123

126–129

84

F MOTOR A, A, B, B

23 ı

26

CN201

FOCUS A, A, B, B

Z DC MOTOR (+), (–)

9 ı

12

ZOOM DC

±

45

46

48

22 ı

35

CP101

CAMERA

MODULE

(1/9)

38

39

XFE CS, XTG CS

40 ı

42

CAM SO, XCAM SCK, XCAM RST

47

CA AD00 – CA AD13

CA HD

CAM F

MCKTG

TG CKI

A6

B5

A4

B4

FOCUS

MOTOR

DRIVER

C1

D2

ZOOM

MOTOR

DRIVER

VSUB CONT IC 301

IC201

B7

B8

C7

C8

LENS DRIVE

(3/9)

HR EN2,

HR DIR2A,

HR DIR2B

HR EN0,

HR DIR0A

B3

A2

B1

XZM DC BR

IRIS M

±, S± 17 ı

20

IRIS M

±, S±

SHUTTER MOTOR (+), (–)

13 ı

16

SHUTTER

±

F PI SENS OUT

Z PI SENS OUT

Z BOX1 PI SENS OUT,

Z BOX2 PI SENS OUT

THERMISTOR (+)

33

29

4

7

30

Q205

G5

H6

G4

H4

IRIS

MOTOR

DRIVER

G3

H2

G2

G1

E7

D7

SHUTTER

MOTOR

DRIVER

F8

F7

H8

IRIS M IN

IRIS M EN

IRIS S IN

IRIS S EN

MSHUT DIR

MSHUT EN

MSHUT REF

XFC RST SENS

XZM RST SENS1

ZM DC FG A, B

1 ı

3

CN757

XE_H

11

12

TRIG 300V

6 ı

8

XE_L

Q601

D601

5

T601

3

4

1

2

ST UNREG

LENS TEMP

5

2

6

IC601

TRANS DRIVE,

FLASH CONTROL,

FLASH CHARGE

DETECT

(9/9)

8

7

4

STRB CHRG

XSTRB FULL

STRB ON

D602

Y7

AB6

AC8

Y11 AB11 Y10

AA11 AB10 Y9

AB9 AA10 AA9

Y8 AB8 AA8

AB7 AA7

AC4

AC22

N3

K3

M4

K4

J3

IC301

CAMERA DSP,

SDRAM

(KWF BOARD)

(2/9)

F1

D1

E1

C6

D7

G1

AC12

AC15

T4

U2

T3

T2

P4

D8

AA12

G4 J2 Y4

G3 H4 W4

STRB ON

U3

AA19

F4

F3

AB20

J23

J22

U20 V21 V23 U22

V20 V22 W20 Y20

W22 Y23 W21 Y22

Y21 AA22 AA21 AB22

J21 L22 L20 L23 K21

L21 M21 M23 M20 M22

N21 N22 N20 P20 P21

P23 R21 P22 T21 R23

R20 R22 T20 T23 U21

P1

CAM SO, XCAM SCK, XCAM RST

PANEL R

PANEL G

PANEL B

HDO

PANEL V

A2

B1

XSYS RST

XPANEL TG CS

BL LEV

C1

A5

B4

A4

B5

G10

D11

E11

F11

IC801

LCD DRIVE

(6/9)

L6

L7

L8

J11

E1 F1 G2

H2 H1 J2

J1 K1 K3

L3 H11

K11 L10

IC302

YO

VIDEO AMP ON

4

1

VIDEO AMP

(2/9)

2

CN754

VR

21

VG

20

VB

22

COM, CS 1

2

RGT, HCK1, HCK2,

HST, PCG, XSTBY,

DWN, EN, VST,

VCK, REF, VP

3 ı

6

11 ı

14

17 ı

19

23

BL H

BL L

26

25

BL L

BL H

BL LEV

V OUT

AU AIN

AU AOUT

SYS SO, XSYS SCK

XSYS RST

SYS V

PANEL UNIT

LCD901

COLOR

LCD

MONITOR

D901

BACKLIGHT

3

OVERALL (2/2)

(PAGE 3-4)

D21

XPANEL TG CS

SYS SI, SYS SO, XSYS SCK

XSYS RST

SYS V

AD16

A11

B11

C11

D14

K2

AA8

IC502

MC CAM,

SH DSP,

FLASH

(4/9)

MC XCS IC 301REG

MC XCS IC 301SDRAM

MC D0 – D15

MC A1 – A25

MC CKIO

CAM F

XFE CS

XTG CS

LENS TEMP

XZM DC BR

MSHUT REF

VER EXTAL

A12

B12

C23

AA19

G2

A6

A7

H1

AC12

AA9

AC16

A2

A17

C18

L21 L23 M24 K23

H22 J21 J22 F24

K21 H21 M23 K22

G21 L24 F23 E23

V22 V21 V23 R22 W22

U22 W21 T22 R23 N21

P22 P21 P23 R21 M22

T21 P24 U21 U23 N22

U24 N23 T24 M21 T23

X101

27MHz

C22

B16

B15

D16

STRB CHRG

XSTRB FULL

AD19

AC15

AA18

D22

AB7

AD14

J1

K1

L1

M1

XAU LINE MUTE

AU SEN

MELODY ENV

MELODY

USB PHY D

±

F1

H23

PRELAMP AF CONT

SELF TIMER LED

AD20

AE LOCK LED

XACCESS LED

MC MSDIO,

MC MSBS,

MC MSCLK

CN751

AB5

AB13

B13

D13

C13

AD11

D11

XMS IN

XAE LOCK ON

XSHTR ON

FR SI, FR SO, XFR SCK

FR INT

XCS MC

9

11

4

7

1

OVERALL (2/2)

(PAGE 3-3)

MEMORY STICK

CONNECTOR

(FP-161 FLEXIBLE)

2

Q752

LED

DRIVE

INT

D753

(MS ACCESS)

DIO, BS, SCLK

CN001

4

2

8

6

OVERALL (2/2)

(PAGE 3-3)

MEMORY

STICK

05

DSC-P200

3-1 3-2

3-2. OVERALL BLOCK DIAGRAM (2/2)


SY-123 BOARD (2/2)

OVERALL (1/2)

(PAGE 3-2)

1

V OUT

USBPHY D

±

AU AIN

AU AOUT

SYS SO, XSYS SCK

XAU LINE MUTE

AU SEN

MELODY ENV

MELODY

AE LOCK LED

PRELAMP AF CONT

SELF TIMER LED

2

CN707

MIC IN

CD-517 FLEXIBLE BOARD (2/2)

D104

SELF TIMER/

AF ILLUMINATOR

PRELAMP AF ON

38

CN101

(2/2)

Q701

LED

DRIVE

D103

(AE/AF LOCK)

XAE LOCK LED

43

Q503

LED

DRIVE

AE LOCK LED

D101

(FLASH/CHG)

XCHARGE/XSTRB LED

44

CONTROL SWITCH

BLOCK (RL)

S001

(SHUTTER)

CONTROL SWITCH

BLOCK (SW51740)

1

CN003

XAE LOCK ON

XSHTR ON

2

6

5

CN756

D001

(POWER)

S002

POWER

3

5

XPWR LED

XPWR ON

MODE

DIAL

4

2

8

11

T

(ZOOM)

W

MIC901

MICROPHONE

FUNCTION

KEY

18

19

H6

H7

F1

Q504

MODULATOR

BEEP

H2

H3

G4

H4

IC901

AUDIO AMP

(7/9)

C1

A2

A4

AE LOCK LED

A7

2

OVERALL (1/2)

(PAGE 3-2)

XCHARGE/XSTRB LED

XPWR LED

XPWR ON

MODE DIAL 0, 1

KEY AD 0, 1

XMS IN

FR INT

XCS MC

XSYS RST

SYS V

XSHTR ON

XAE LOCK ON

V OUT

CN704

(1/2)

34

AU OUT

31

XAV JACK IN

22

USBPHY D

±

26

28

USB JACK IN

24

SP

±

CN758

1

2

USB JACK IN

Q408

XAV JACK IN

Q401

FR SI, FR SO, XFR SCK

X401

32.768kHz

PLL

LOOP

FILTER

B1

B2

B8

J8

J9

J5

J4

C8

A3

B6

D1

D2

E1

D9

E2

B3

B9

IC401

FRONT

CONTROL

(5/9)

D7

E8

F9

F7

E9

A8

J7

H7

A7

G1

G2

J2

J3

RESET

Q407

BATTERY

CHARGE

DETECTOR

S401

XRSTX

CHG STAT 0 – 2

SYS DD ON

C1

D3

H1

DDCON SO, DDCON SCK

XCS DDCON

A9

H2

J1

BATT IN

FAST CHARGE

INIT CHARGE

L8

K8

K7

A7

E3

D2

B7

C7

D7

BATT/XEXT

BATT SIG

E4

J6

H6

V OUT

A OUT L

XAV JACK IN

D

±

USB VBUS

SP901

SPEAKER

20

16

26

10

12

6

CN101

(MULTI CONNECTOR)

FP-162 FLEXIBLE BOARD

21

23

25

19

15

9

7

2

17

24

ACV UNREG

BATT XEXT

KEY ADA, ADB

XLANC POWER ON

CHG STAT 0 – 2

CN704

(2/2)

23 20 36 17 19 18 21 1

ACV UNREG

2 – 9 37–44 45

BATT /XEXT D

BATT UNREG

BATT SIG

PANEL 8.5V

BACK UP VCC

EVER 3.0V

A 3.1V

D 1.2V

D 2.8V

A 2.8V

CAM 15.5V

CAM –7.5V/–8.0V

CAM 3.3V

M 5V

ST 5V

CAM –0.5V

IC002

DC/DC

CONTROL,

RESET

(8/9)

G1

G2

B1

IC402

DC JACK/MULTI DOUBLE

INSERTION DETECT

(5/9)

ACV UNREG

ST UNREG

BATT UNREG

ACV UNREG

BL H

BL L

BL LEV

Q402

BUFFER

ACV W SENS

CHG SW

Q008,

009

3

OVERALL (1/2)

(PAGE 3-2)

KEY AD 2

BT001

LITHIUM

BATTERY

12

15

VL 3V

G6

VL 3V

A10

D8

A

: VIDEO SIGNAL

A

: AUDIO SIGNAL

A : VIDEO/AUDIO SIGNAL

05

J101

DC IN

+

S

−

BT901

BATTERY

TERMINAL

DSC-P200

3-3 3-4

3-3. POWER BLOCK DIAGRAM (1/2)


BT901

BATTERY

TERMINAL

+

S

−

FP-162 FLEXIBLE BOARD SY-123 BOARD (1/2)

BATT UNREG1

BATT SIG

37 ı

44

45

CN704

Q008,

009

F001

J101

DC IN

CN101

MULTI

CONNECTOR

LF101

ACV UNREG1

2 ı

9

21

23

25

19

7

2

17

24

ACV UNREG

BATT/XEXT D

BATT/XEXT M

XLANC POWER ON

CHG STAT0 – 2

1

21

17

23

20

36

CONTROL SWITCH

BLOCK (SW51740)

VL 3V

15

CN756

BT001

LITHIUM

BATTERY

CONTROL SWITCH

BLOCK (RL)

D001

(POWER)

4

CN003

EVER 3.0V

3

2

1

4

IC402

DC JACK/MULTI DOUBLE

INSERTION DETECT

(5/9)

VL 3V

F002

Q407

BATTERY

CHARGE

DETECTOR

Q402

BUFFER

CHG STAT0 – 2

D006

D002

D005

F004 L001, 010

L009

IC002

DC/DC CONTROL, RESET

(8/9)

D9 OUT8A

E9 OUT8B

B11

VCC8

E4 CHG SW

D1

VDCIN

E5 MARK

D4 BATT

D8

VBCK

G11 VCC1A

G10 VCC1B

G9

VCC1C

CBG B5

VCH1A L10

VCH1B K9

VCH1C (FB4) L9

VLDO1 A11

D 1.2V

ACV UNREG

D004

L005

K5 VCC5

VCH2 E11

OUT2 F10

L002

VCH3A (FB3) J1

VCH3B H4

VCH3C (FB6) H3

VCH3S H2

VCC GD H1

VCH4 J6

D009

OUT4 K6

VLDO4 C8

L006

VCH5 J5

OUT5 L5

D008

VLDO5 B8

L007

IC401

FRONT CONTROL

(5/9)

G8 ACV SENS

H8 BATT SENS

F8 DD CON SENS

F9 VCC2

B9 VLDO2

A10 VLDO3

J3

OUT3A

K1 OUT3B

J2 OUT3C

G1

G2

BATT SO

BATT SI

A7

A8 XLANC PWR ON

F9

F7

E9

BATT/XEXT

CHG STAT0

CHG STAT1

CHG STAT2

C1

D3

H1

A9

H2

J1

E8

DDCON SO,

DDCON SCK

XCS DDCON

BATT IN

FAST CHARGE

INIT CHARGE

SYS DD ON

L8

K8

DIN

CLK

K7 LD

A7 CS

E3 FCHG

D2 ICHG

C7

D7

SYSDDON

USB PWR ON

VCH6 G1

D007

OUT6 F1

ICH6 G2

REF6 B1

L003

VCC7 J4

VOS72 K4

VOS73 L3

VCH7 K3

EVER 3.0V

05

ST UNREG

CAM –0.5V

DC

CONTROL

(8/9)

1

4

IC003

Q001

SWITCHING

L011

A 2.8V

D 2.8V

EVER 3.0V

D 1.2V

M 5V

ST 5V

A

POWER 2

(PAGE 3-7)

CAM 15.5V

A 3.1V

CAM –8.0V

PANEL 8.5V

BL H

BL L

BL LEV

CAM 3.3V

Q011, 012

SWITCHING

L012

Q010

DC CONTROL

DSC-P200

3-5 3-6

DSC-P200

05

3-4. POWER BLOCK DIAGRAM (2/2)


SY-123 BOARD (2/2)

ST UNREG

L601

T601 CN757

1 ı

3

FP-163 FLEXIBLE

BOARD

ST UNREG FLASH

UNIT

ST 5V

IC601

TRANS DRIVE,

FLASH CONTROL,

FLASH CHARGE

DETECT

(9/9)

PANEL UNIT

PANEL 8.5V

L804

CN754

7

VDD

BL LEV

BL H

BL L

POWER 1

(PAGE 3-6)

A

CAM 3.3V

CAM –0.5V

CAM 15.5V

CAM –8.0V

M 5V

A 2.8V

D 2.8V

EVER 3.0V

A 3.1V

D 1.2V

M 5V (PANEL 4.9V)

IC802

CAM 3.3V

A 2.8V (PANEL 2.8V)

5

2.8V

REG

(6/9)

4

L813

L901

A 2.8V

AU 2.8V

IC901

AUDIO AMP

(7/9)

IC801

LCD DRIVE

(6/9)

EXTDA G10

26

25

BL H

BL L

LCD901

COLOR

LCD

MONITOR

D901

BACKLIGHT

L104

L103

FB105

L105

FB102

FB103

CP101

CAMERA MODULE

(1/9)

50

51

49

54

55

71

52

57

53

56

CH-146 BOARD

IC101

CCD SIGNAL

PROCESSOR,

TIMING

GENERATOR

A 2.8V

D 2.8V

Q101, 102

CAM 3.3V

CAM –0.5V

CAM 15.5V

CAM –8.0V

M 5V

A 2.8V

EVER 3.0V

L504

D 2.8V

L304

L301

D 1.2V

A 3.1V

D 1.2V

L302

L303 IC302

VIDEO AMP

(2/9)

FB304

FB301

FB302

FB305

IC301

CAMERA DSP,

SDRAM

(KWF BOARD)

(2/9)

PI006 V4

PI007 V3

CAM DD ON

L503

A 2.8V

D2.8V

IC501

4

1.8V REG

(4/9)

1

L502

AC20

XLENS RST LED

XZM RST LED

PU[6]

IC502

MC CAM,

SH DSP,

FLASH

(4/9)

SDA(O/D) AD18

MS POWER ON

D 2.8V

D 2.8V

IC201

LENS DRIVE

(3/9)

Q751

Q201 (1/2)

Q201 (2/2)

D 2.8V

M 5V

CD-517 FLEXIBLE BOARD

L101

CN101

12

FB108

1

CAM 15V

CAM –8.0V

39

M 5V

IC101

CCD IMAGER

D104

SELF TIMER/

AF ILLUMINATOR

40

D 2.8V (XAE LOCK)

45

EVER 3.0V

D103

(AE/AF LOCK)

D101

(FLASH/CHG)

CN751

2

MEMORY STICK CONNECTOR

(FP-161 FLEXIBLE)

CN001

VCC

CN201

32

F PI SENS Vcc

28

Z PI SENS Vcc

6

1

Z BOX2 PI

SENS Vcc

Z BOX1 PI

SENS Vcc

LENS BLOCK

FOCUS

SENSOR

ZOOM

FG

9

MEMORY

STICK

3-7 3-8E

4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM

1 2 3 4

FRAME SCHEMATIC DIAGRAM

A

5

B

6

FP-163

FLEXIBLE

BOARD

(FLASH)

C

D

E

F

CONTROL SWITCH

BLOCK(RL)

MIC901

MIC

CONTROL

SWITCH

BLOCK

(SW51740)

CN756

19P

REG_GND

XPWR_ON

EVER_3.0V

XPWR_LED

XSHTR_ON

XAE_LOCK_ON

MANUAL

MODE_DIAL1

MOVIE

PB

MODE_DIAL0

KEY_AD2

REG_GND

NC

VL_3V

NC

REG_GND

KEY_AD1

KEY_AD0

11

12

13

14

7

8

9

10

15

16

17

18

19

3

4

1

2

5

6

G

SP901

SPEAKER

1

2

CN758 2P

SP-

SP+

7

C601

CHARGING

CAPACITOR

FLASH UNIT

8

SY-123 BOARD

(1/9) (CAMERA MODULE)

(2/9) (CAMERA DSP)

(3/9) (LENS DRIVE)

(4/9) (SH DSP)

(5/9) (FRONT CONTROL)

(6/9) (LCD DRIVE)

(7/9) (AUDIO)

(8/9) (DC/DC CONVERTER)

(9/9) (CONNECTOR)

9 10 11

CP101

CH-146

BOARD

CCD SIGNAL

PROCESS

IC301

KWF

BOARD

12 13 14

H

I

J

K

PANEL UNIT

LCD901

2.0 INCH

COLOR

LCD MONITR

D901

BACKLIGHT

BT901

BATTERY

TERMINAL

J101

DC IN

FP-162 FLEXIBLE BOARD

(DC IN, MULTI CONNECTOR)

CN101

28P

(MULTI CONNECTOR)

27

CHG_STAT0

NC(FR_EXT_BATT)

USB_VBUS

USB_GND

D+

D-

USB_GND

ACV_GND

ACV_GND

ACV_GND

XLANC_POWER_ON

KEY_ADB

N.C.

N.C.

KEY_ADA

CHG_STAT1

A_OUT_L

A_GND

V_OUT

V_GND

CHG_STAT2

XAV_JACK_IN

BATT_XEXT

ACV_UNREG

ACV_UNREG

ACV_UNREG

28

TO AV/USB MULTI CABLE OR CRADLE

MEMORY

STICK

CONNECTOR

FP-161

FLEXIBLE

BOARD

15

CN201

33P

F_PI_SENS_OUT

F_PI_SENS_Vcc

REG_GND

THERMISTOR(+)

33

32

31

30

Z_PI_SENS_OUT

Z_PI_SENS_Vcc

N.C.

F_MOTOR B

F_MOTOR A

F_MOTOR B

F_MOTOR A

N.C.

N.C.

IRIS_M_-

IRIS_M_+

IRIS_S_-

IRIS_S_+

SHUTTER_MOTOR(-)

SHUTTER_MOTOR(-)

SHUTTER_MOTOR(+)

SHUTTER_MOTOR(+)

Z_DC_MOTOR(-)

Z_DC_MOTOR(-)

Z_DC_MOTOR(+)

Z_DC_MOTOR(+)

REG_GND

Z_BOX2_PI_SENS_OUT

Z_BOX2_PI_SENS_Vcc

Z_BOX2_PI_SENS_Col

Z_BOX1_PI_SENS_OUT

REG_GND

Z_BOX1_PI_SENS_Col

Z_BOX1_PI_SENS_Vcc

24

23

22

21

20

19

18

17

29

28

27

26

25

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

V4

VHLD

V3A

V3B

PRELAMP_AF_ON

M_5V

D_2.8V(AE_LOCK)

XAE_LOCK_LED

V2

VST

V1

N.C.

N.C.

N.C.

XCHARGE/XSTRB_LED

EVER_3.0V

42

43

44

45

38

39

40

41

34

35

36

37

30

31

32

33

CDD_OUT

N.C.

CCD_GND

GND

GND

VSUB

VSUB_CONT

V10

V9

V8

V7

V6

V5B

V5A

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

CN101 45P

CAM_-8.0V

GND

GND

RG

GND

H2A

H2B

GND

H1A

H1B

GND

CAM_15V

PWR_SAVE

GND

GND

21

22

23

24

17

18

19

20

25

26

27

28

29

16 17

CD-517

FLEXIBLE

BOARD

(CCD IMAGER)

18

LENS FLEXIBLE

19

GEAR

BOX

20

LENS BLOCK

OVF

LENS

CCD

21

L

11 12

MEMORY

STICK

MEMORY STICK

Note: FP-161 flexible board is supplied as MEMORY STICK CONNECTOR.

05

DSC-P200

4-1 4-2

FRAME

DSC-P200

4-2. SCHEMATIC DIAGRAMS

CD-517 FLEXIBLE

(CCD IMAGER)

FP-163 FLEXIBLE BOARD

(FLASH)

4-2. SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS

(In addition to this, the necessary note is printed in each block)

(For schematic diagrams)

•

All capacitors are in

µ

F unless otherwise noted. pF :

µ

Link

and tantalums.

•

Chip resistors are 1/10 W unless otherwise noted.

k

Ω

=1000

Ω

, M

Ω

=1000 k

Ω

.

•

Caution when replacing chip parts.

New parts must be attached after removal of chip.

Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat.

•

Some chip part will be indicated as follows.

Example C541 L452

22U 10UH

TA A 2520

1. Connection

Pattern box

Pattern box

Pattern box PTB-450

J-6082-200-A

or

Small pattern box

PTB-1450

J-6082-557-A

Color bar chart

For PTB-450:

J-6020-250-A

For PTB-1450:

J-6082-559-A

L = About 28 cm(PTB-450)

L = About 12 cm(PTB-1450)

USB,AV cable for multi-use terminal

L

Kinds of capacitor

Case Size

External dimensions (mm)

•

Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used.

In such cases, the unused circuits may be indicated.

•

Parts with

★

differ according to the model/destination.

Refer to the mount table for each function.

•

All variable and adjustable resistors have characteristic curve B, unless otherwise noted.

•

Signal name

XEDIT

→

EDIT PB/XREC

→

PB/REC

•

2

: non flammable resistor

•

5

: fusible resistor

•

C

: panel designation

•

A

: B+ Line

•

B

: B– Line

•

J

: IN/OUT direction of (+,

−

) B LINE.

•

C

: adjustment for repair.

•

A

: not use circuit

•

Circled numbers refer to waveforms.

(Measuring conditions voltage and waveform)

•

Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms.

(VOM of DC 10 M

Ω

input impedance is used)

•

Voltage values change depending upon input impedance of VOM used.)

Front of the lens

2. Adjust the distance so that the output waveform of

Fig. a and the Fig. b can be obtain.

H

B B

A A=B/2

A

Fig. a (Video output terminal output waveform)

Electronic beam scanning frame

CRT picture frame

Fig.b (Picture on monitor TV)

When indicating parts by reference number, please include the board name.

Note :

The components identified by mark

0

or dotted line with mark

0

are critical for safety.

Replace only with part number specified.

Note :

Les composants identifiés par une marque

0

sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifie.

DSC-P200

4-5

For Schematic Diagram

•

Refer to page 4-37 for printed wiring board.

1 2 3 4 5 6 7

A

B

C

D

E

F

G

CD-517 FLEXIBLE BOARD

CCD IMAGER (CCD BLOCK)

XX MARK:NO MOUNT

D101

SML-310YTT86

(FLASH/CHG)

SY-123

(1/9)

CN101

PAGE 4-11 of LEVEL3

LND101

LND102

LND103

LND104

LND105

LND106

LND107

LND108

LND109

LND110

LND111

LND112

LND113

LND114

LND115

LND116

LND117

LND118

LND119

LND120

LND121

LND122

LND123

LND124

LND125

LND126

LND127

LND128

LND129

23

22

21

20

19

18

LND130

LND131

LND132

LND133

LND134

LND135

LND136

13

12

11

17

16

15

14

LND137

LND138

LND139

LND140

LND141

LND142

30

29

28

27

26

25

24

33

32

31

7

6

5

10

9

8

LND143

LND144

LND145

4

3

2

1

36

35

34

45

44

43

42

EVER_3.0V

XCHARGE/

XSTRB_LED

N.C.

N.C.

41

40

XAE_LOCK_LED

D_2.8V

(AE_LOCK)

M_5V 39

38

PRELAMP_AF_ON

37 N.C.

V1

VST

V2

V10

VSUB_CONT

VSUB

GND

GND

CCD_GND

N.C.

CCD_OUT

GND

GND

PWR_SAVE

CAM_15V

GND

H1B

H1A

GND

H2B

H2A

GND

RG

GND

GND

CAM_-8.0V

V3B

V3A

VHLD

V4

V5A

V5B

V6

V7

V8

V9

D102

XX

D103

CL-196HR-CD-T

(AE/AF LOCK)

D104

OPY5252

(SELF TIMER/AF ILLUMINATOR)

C101

XX

R101

33

R109

0

Note: CD-517 flexible complete board and IC101 are not supplied, but there are included in

CCD block assy.

Note: Voltage and Waveform of mounted on

CD-517 flexible board can not be measured, because they are mounted by the side of the lens.

Q101

DTC144EMT2L

SWITCH

R102

12k

Q103

2SC4250(T5LSONY1)

BUFFER

R103

2700

C103

XX

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

IC101

CCD IMAGER

IC101

ICX489CQZ-13

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

R104

1200

R105

1500

C102

0.1u

C105

0.1u

C106

0.1u

Q102

DTC144EMT2L

SWITCH

H

8

05

Precautions for Replacement of CCD Imager

• The CD-517 flexible board mounted as a repair part is not equipped with a CCD imager.

When replacing this board, remove the CCD imager from the old one and mount it onto the new one.

• If the CCD imager has been replaced, carry out all the adjustments for the camera section.

• As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC.

In addition, ensure that the receiver is not covered with dusts nor exposed to strong light.

DSC-P200

4-7 4-8

CD-517

DSC-P200

Schematic diagrams of the CH-146, SY-123 boards are not shown.

Pages from 4-9 to 4-28 are not shown.

For Schematic Diagram

•

Refer to page 4-43 for printed wiring board.

1 2

A

B

C

D

E

F

G

3 4 5 6 7


DC IN, MULTI CONNECTOR (JK BLOCK)

XX MARK:NO MOUNT

NO MARK:REC/PB MODE

LND145

45

LND144

44

LND143

43

LND142

42

BATT_SIG

BATT_UNREG

BATT_UNREG

BATT_UNREG

LND146

BATT_UNREG

LND147

BATT_SIG

LND148

BATT_GND

SY-123

(9/9)

CN704

PAGE 4-28 of LEVEL3

LND141

41

LND140

40

LND139

39

LND138

38

LND137

37

LND136

36

LND135

35

BATT_UNREG

BATT_UNREG

BATT_UNREG

BATT_UNREG

BATT_UNREG

CHG_STAT2

V_GND

LND134

34

LND133

33

LND132

32

V_OUT

V_GND

A_GND

LND131

31

LND130

30

A_OUT_L

NC

LND129

29 USB/LANC_GND

LND128

28

LND127

27

D-

NC

LND126

26 D+

LND125

25

USB/LANC_GND

LND124

24 USB_VBUS

LND123

23

LND122

22

CHG_STAT0

XAV_JACK_IN

LND121

21

LND120

20

LND119

19

BATT/XEXT_M

CHG_STAT1

KEY_ADA

LND118

18 KEY_ADB

LND117

17

XLANC_POWER_ON

LND116

16

LND115

15

LND114

14

GND

GND

GND

LND113

13

LND112

12

LND111

11

LND110

10

LND109

9

LND108

LND107

8

7

LND106

LND105

6

GND

GND

GND

GND

ACV_UNREG1

ACV_UNREG1

ACV_UNREG1

ACV_UNREG1

LND104

5

4

ACV_UNREG1

ACV_UNREG1

LND103

LND102

LND101

3

2

1

ACV_UNREG1

ACV_UNREG1

BATT/XEXT_D

3

2

D101

MA2S111-(K8).SO

LF101

0uH

4

1 1

2

3

5

4

BT901

BATTERY

TERMINAL

S

CHG_STAT0

NC(FR_EXT_BATT)

USB_VBUS

USB_GND

D+

D-

USB_GND

A_OUT_L

A_GND

V_OUT

V_GND

CHG_STAT2

XAV_JACK_IN

CN101 28P

(MULTI CONNECTOR)

TO AV/USB MULTI CABLE OR CRADLE

J101

DC IN

Note: CN101 (multi connector) is not supplied, but this is included in FP-162 flexible complete board.

27

28

LND149

STATIC_GND

LND150

STATIC_GND

ACV_GND

ACV_GND

ACV_GND

XLANC_POWER_ON

KEY_ADB

N.C.

N.C.

KEY_ADA

CHG_STAT1

BATT_XEXT

ACV_UNREG

ACV_UNREG

ACV_UNREG

05

DSC-P200

4-29

A

1

2 3 4 5


FLASH (STROBE BLOCK)

Note: FLASH UNIT and C601 are not included in FP-163 flexible complete board.

LND518

LND517

LND516

1

2

3

XE_H

XE_H

XE_H

LND521

XE_H

B

FLASH

UNIT

LND523

TRIG_300V

LND524

TRIG_GND

C

SY-123

(9/9)

CN757

PAGE 4-28 of LEVEL3

LND513

LND512

5

6

LND511

7

XE_L

XE_L

XE_L

LND508

11

LND507

12

TRIG_300V

TRIG_300V

LND503

LND502

16

17

LND501

18

ST_GND

ST_GND

ST_GND

D

05

XE_L

LND522

CL501

CL502

C601

117u

315V

CHARGING

CAPACITOR

A

1 2 3 4

MEMORY STICK CONNECTOR

(FP-161 FLEXIBLE BOARD)

MEMORY STICK CONNECTOR (FP-161 flexible board) is replaced as block, so that PRINTED WIRING BOARD is omitted.

B

C

D

SY-123

(9/9)

CN751

PAGE 4-27 of LEVEL3

LND001

1

LND002

2

LND003

3

LND004

4

LND005

5

LND006

6

LND007

7

LND008

8

LND009

9

LND010

10

LND011

11

LND012

12

DATA3

INT

DATA2

DIO

DATA1

BS

VSS

VSS

VCC

VSS

SCLK

VSS

LND013

STATIC_GND

05

6

5

4

3

2

1

10

9

CN001 12P

VSS

VCC

8

7

SCLK

DATA3

INT

DATA2

DIO

DATA1

BS

VSS

5

12

MEMORY

STICK

MEMORY

STICK

11

The components identified by mark

0

or dotted line with mark 0 are critical for safety.



0


Ne les remplacer que par une piéce portant le numéro spécifié.

4-30

FP-162, FP-163, MEMORY STICK CONNECTOR (FP-161)

I

A

B

C

D

E

F

G

1 2 3 4 5 6 7 8 9 11

SY-123

(5/9)

CN756

PAGE 4-19 of LEVEL3

REG_GND

XPWR_ON

EVER_3.0V

CL001

CL002

CL003

XPWR_LED

XSHTR_ON

XAE_LOCK_ON

MANUAL

MODE_DIAL1

MOVIE

PB

MODE_DIAL0

KEY_AD2

REG_GND

CL011

CL012

CL013

VL_3V

NC

CL015

CL004

CL005

CL006

CL007

CL008

CL009

CL010

REG_GND

KEY_AD1

KEY_AD0

NC

CL017

CL018

CL019

XPWR_ON

EVER_3.0V

XPWR_LED

XSHTR_ON

XAE_LOCK_ON

BT001

LITHIUM

BATTERY

CONTROL SWITCH BLOCK (SW51740)

CONTROL SWITCH BLOCK (SW51740) is replaced as block, so that PRINTED WIRING BOARD is omitted.

R008

3300

CL032

(FLASH)

CL035 CL033

(MACRO)

CL034

CL031

(SET)

CL030

R007

1500

(REVIEW)

CL029

CL028

KEY_AD1

KEY_AD0

W

T

CL040

KEY_AD2

W (ZOOM) T

CL045

R005

1200

CL038 CL039

R006

1200

R009

1200

R010

1500

R011

3300

IMAGE SIZE/

DELETE

CL025

CL024

CL020

MENU

CL021

(SELF TIMER)

CL027 CL026

DISPLAY/

LCD ON/OFF

CL022

CL023

XPWR_ON

EVER_3.0V

XPWR_LED

XSHTR_ON

XAE_LOCK_ON

6

5

4

3

2

1

CN003

REG_GND

6P

XPWR_ON

EVER_3.0V

XPWR_LED

XSHTR_ON

XAE_LOCK_ON

12

H

J

MODE_DIAL0

6 POSITION MODE_DIAL

MOVIE

PB

CL036

6

5

CL046

CL048

CL042

4

SCN

AUTO

1

CL044

CL041

CL043

2

P_AUTO

R002

1500

3

MANUAL

R001

1200

MODE_DIAL1

13 14 15 16

REG_GND 1

XPWR_ON 2

EVER_3.0V

3

XPWR_LED _ON 4

XSHTR_ON

5

XAE_LOCK _ON 6

CONTROL SWITCH BLOCK

(RL)

CONTROL SWITCH BLOCK (RL) is replaced as block, so that PRINTED WIRING BOARD is omitted.

S002

POWER

D001

(POWER)

(1st)

(2nd)

S001

(SHUTTER)

NO

K

05

DSC-P200

4-31 4-32

(SW51740), (RL)

DSC-P200

4-3. PRINTED WIRING BOARDS

Board Name

CD-517 flexible

FP-162 flexible

FP-163 flexible

Function

CCD IMAGER

DC IN, MULTI CONNECTOR

FLASH

4-3. PRINTED WIRING BOARDS

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS

•

•

: Uses unleaded solder.

: Circuit board

: Flexible board

Pattern from the side which enables seeing.

: pattern of the rear side

(The other layers’ patterns are not indicated)

• Through hole is omitted.

• Circled numbers refer to waveforms.

• There are a few cases that the part printed on diagram isn’t mounted in this model.

•

C

: panel designation

• Chip parts.

Transistor

C 6 5 4 4 5 6 5 4 4 5

Diode

3 3

B E 1 2 3

1 2

3 2 1

2 1

1 2 3

3 2

3 2 1

5 4 3 3 4 5 4 1

3 1 2 3

2 1

4 3

2 1

3 4

2 1

6 5 4

6 5 4

4 5 6

1 2

3 2

2 1 1 2 3 3 2 1

4 1

Board Name

CD-517 flexible

FP-162 flexible

FP-163 flexible

Parts Location

(Shown on Page)

4-47

–

–

Pattern

Total Number of Layers Layers Not Indicated

2 layers

2 layers

1 layer

–

–

–

DSC-P200

4-35

CD-517 FLEXIBLE

Note for Printed Wiring Board (See page 4-35).

: Uses unleaded solder.

CD-517 FLEXIBLE BOARD

A

LND122

LND123

LND124

LND125

LND126

LND127

LND128

LND129

LND130

LND131

LND132

LND133

LND134

LND135

LND136

LND137

LND138

LND139

LND140

LND141

LND142

LND143

LND144

LND145

LND101

LND102

LND103

LND104

LND105

LND107

LND106

LND108

LND109

LND110

LND111

LND112

LND113

LND114

LND115

LND116

LND117

LND118

LND119

LND120

LND121

B

45

D104

SELF TIMER/

AF ILLUMINATOR

D104

C

1

05

1 2

>PI<

CD-517

A

D103

K

K

D102

A

K

D101

A

D103

(AE/AF LOCK)

D101

(FLASH/CHG)

Note: CD-517 flexible complete board and IC101 are not supplied, but there are included in

CCD block assy.

R101

C101

R103

R102

Q101

B

E

C

R109

C106

Q103

B

C

E

C103

C102

B

C

E

Q102

R104

R105

C104

3

16 15 3 2

1

17

18 19

CL103 CL107

IC101

CL111

CL102

CL114

CL120

CL121

31 32

C107 C105

4

1-864-518-

11

DSC-P200

4-37 4-38

CD-517

DSC-P200

Printed wiring boards of the CH-146, SY-123 boards are not shown.

Pages from 4-39 to 4-42 are not shown.

Note for Printed Wiring Board (See page 4-35).

FP-162 FLEXIBLE



DC IN

05

Note: CN101 (multi connector) is

not supplied, but this is included

in FP-162 flexible complete board.

LF101

27

(MULTI CONNECTOR)

CN101

1 5 15 25

28

D101

2 10 20

26

1-864-11211

1 45

BT901

BATTERY

TERMINAL

S

DSC-P200

4-43

FP-163 FLEXIBLE



FLASH UNIT

XE H

TRIG 300V

TRIG GND

LND521

1-864-113-

FP-163

FX

1 >PI<

LND524 LND523

XE L

LND522

1

05

1-864-11311

Note: FLASH UNIT and C601 are not included in FP-163 flexible board.

18

CL502

C601

CHARGING

CAPACITOR

+

CL501

FP-162, FP-163

4-44

DSC-P200

Waveforms of the SY-123 board are not shown.

Pages 4-45 and 4-46 are not shown.

4-5. MOUNTED PARTS LOCATION

CD-517 FLEXIBLE BOARD

C102 C-3

C105 C-4

C106 C-3

C107 C-4

D101 B-2

D103 A-2

D104 B-1

IC101 C-4

Q101 C-3

Q102 C-3

Q103 C-3

R101 C-3

R102 C-3

R103 C-3

R104 C-3

R105 C-3

R109 C-3 no mark : side A

*

mark : side B

DSC-P200

4-47

CD-517

DSC-P200

Mounted parts location of the CH-146 and SY-123 boards are not shown.

Page 4-48 and 4-49 are not shown.

5. REPAIR PARTS LIST

NOTE: Characters

A

to

Z

of the electrical parts list indicate location of exploded views in which the desired part is shown.

A B C D

B

C

C

D

DSC-P200

5. REPAIR PARTS LIST

NOTE:

•

-XX, -X mean standardized parts, so they may have some differences from the original one.

•

Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

•

The mechanical parts with no reference number in the exploded views are not supplied.

•

Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.

•

CAPACITORS: uF:

µ

F

•

COILS uH:

µ

H

•

RESISTORS

All resistors are in ohms.

METAL: metal-film resistor

METAL OXIDE: Metal Oxide-film resistor

F: nonflammable

•

SEMICONDUCTORS

In each case, u:

µ

, for example: uA...:

µ

A... , uPA... ,

µ

PA... , uPB... ,

µ

PB... ,

µ

PC... ,

µ

PC... , uPD...,

µ

PD...

•

Abbreviation

AR : Argentina model

AUS : Australian model

BR : Brazilian model

CH : Chinese model

CND : Canadian model

HK : Hong Kong model

JE : Tourist model

KR : Korean model

When indicating parts by reference number, please include the board name.

The components identified by mark 0 or dotted line with mark

0

are critical for safety.



0


Ne les remplacer que par une pièce portant le numéro spécifié.

DSC-P200

5-1

5-1. EXPLODED VIEWS

5-1-1. OVERALL ASSEMBLY

3

Main block assembly

(See Page 5-4)

2

3

4

5

6

12

11

3

1

3

7

8

9

Lens block assembly

(See Page 5-3)

10

3

Ref. No.

Part No.

2

2

1

2

3

Description

2-547-040-01 RING, LENS

2-547-038-01 CABINET (FRONT (SD)) (SILVER)

2-547-038-11 CABINET (FRONT (SD)) (BLACK)

2-547-038-21 CABINET (FRONT (SD)) (BROWN)

2-587-151-01 SCREW (M1.4), NEW TRUSTAR.P2

4

5

6

2-582-197-01 SHEET (FRONT), ADHESIVE

2-582-196-01 SHEET, OVF WINDOW ADHESIVE

2-582-195-01 WINDOW, OVF

DSC-P200

5-2

Ref. No.

Part No.

9

9

7

8

9

Description

2-582-186-01 SHEET, LCD WINDOW ADHESIVE

2-582-185-01 WINDOW, LCD

A-1097-047-A CABINET (REAR) BLOCK ASSY (SILVER)

A-1097-048-A CABINET (REAR) BLOCK ASSY (BLACK)

A-1097-049-A CABINET (REAR) BLOCK ASSY (BROWN)

10

11

12

X-2048-862-1 CABINET ASSY, SIDE

2-582-194-01 CABINET (FRONT), INNER

2-582-184-01 PLATE, CABINET

5-1-2. LENS BLOCK ASSEMBLY

SP901

60

61

51

52

(Note 1)

53

(Note 1)

64

(including CD-517 flexible board and IC101 (CCD IMAGER))

(Note 2)

62

55

56

57

58

59

LCD901

54

(Note 1)

D901

63

Ref. No.

Part No.

51

52

53

54

55

Description

1-788-208-11 LENS, VIDEO (EC01B)

3-091-427-01 RING (A), ORNAMENTAL (Note1)

3-086-156-31 SCREW, TAPPING (P2) (Note1)

X-3954-476-1 BARRIER ASSY (Note1)

3-091-013-01 HOLDER, AF

56

57

58

59

2-021-317-01 MASK, LPF

1-788-176-11 OPTICAL FILTERBLOCK (OFB-02-21)

2-021-318-01 SEALGOM 890

3-348-998-61 SCREW (M1.4X4), TAPPING, PAN

DSC-P200

5-3

Note 1: Be sure to read “2-3. Exchange Method of Barrier Assy” on page 2-7 when change Ref. No. 52, 53 and 54.

Note 2: Be sure to read “Precuations for Replacement of CCD

Imager” on page 4-8 when changing the CCD imager.

Ref. No.

Part No.

60

61

62

63

64

Description

2-582-219-01 FRAME, LENS

3-080-204-11 SCREW, TAPPING, P2

2-589-437-01 GUARD (CD), FLEXIBLE

2-582-218-01 SHEET, BL HARNESS PROTECTION

A-1089-498-A CCD BLOCK ASSY (including CD-517 flexible board and IC101 (CCD IMAGER)) (Note2)

D901 1-479-010-11 BLOCK, LIGHT GUIDE PLATE (2.0)

LCD901 8-753-228-05 ACX335AK-3

SP901 1-825-923-31 LOUDSPEAKER (1.3CM)

5-1-3. MAIN BLOCK ASSEMBLY

ns: not supplied

106

MIC901

102

(including CP101

(CH-146 board) and IC301 (KWF board))

104

(Note 1)

111

J101 ns

(CN101)

BT901

!

ns

(BT001)

101

103

110

ns

106

ns

105

(including BT001)

107

108

(Note 2)

BT block assembly

(See Page 5-5)

109

!

BT001(BATTERY, LITHIUM SECONDARY)

112

Note 1: CN101 (multi connector) is not supplied, but this is included in FP-162 flexible complete board.

Note 2: Part of 108 is including FP-161 flexible board.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

The components identified by mark 0 or dotted line with mark 0 are critical for safety.


Les composants identifiés par une marque 0 sont critiques pour la sécurité.


Ref. No.

Part No.

101

102

102

102

102

Description

3-080-222-31 SCREW (M1.7), TAPPING, P2

A-1107-528-A SY-123 BOARD, COMPLETE (SERVICE)

(including CP101

(CH-146 board) and IC301 (KWF board)) (E)


(including CP101 (CH-146 board) and IC301 (KWF board)) (HK, KR, CH, JE)


(including CP101 (CH-146 board) and IC301 (KWF board)) (US, CND, AUS)


(including CP101 (CH-146 board) and IC301 (KWF board)) (AEP, UK)

Ref. No.

0 104

105

106

107

108

Part No.

Description

A-1086-398-A FP-162 FLEXIBLE BOARD, COMPLETE (Note 1)

1-479-099-11 CONTROL SW BLOCK (SW51740)

(Including BT001)

3-080-204-11 SCREW, TAPPING, P2

2-582-202-01 SHEET, CCD RADIATION

1-819-094-11 CONNECTOR, MEMORY STICK 10P (Note 2)

109

110

111

112

2-582-205-01 SHEET, MS RADIATION

2-590-642-01 SHEET, SY RADIATION

1-479-100-11 SWITCH BLOCK, CONTROL

2-592-676-01 MS SPACER

0 BT901 1-780-141-21 BATTERY TERMINAL BOARD

103 2-582-200-01 SHEET, JK

0 J101 1-817-331-11 DC JACK 5P (DC IN)

MIC901 1-542-623-11 MICROPHONE UNIT

DSC-P200

5-4

5-1-4. BT BLOCK ASSEMBLY

ns: not supplied

152

157

156

(Note)

158

153

ns

154

151

C601

(Note)

159

155

Note: FLASH UNIT and C601 are not included in FP-163 flexible board.

Ref. No.

151

151

151

152

152

152

153

153

153

Part No.

Description

X-2048-864-1 HOLDER ASSY, BATTERY (SILVER)

X-2048-866-1 HOLDER ASSY, BATTERY (BLACK)

X-2048-867-1 HOLDER ASSY, BATTERY (BROWN)

2-547-035-01 LID, DC JACK (SILVER)

2-547-035-11 LID, DC JACK (BLACK)

2-547-035-21 LID, DC JACK (BROWN)

2-547-036-01 LID, BATTERY (SILVER)

2-547-036-11 LID, BATTERY (BLACK)

2-547-036-21 LID, BATTERY (BROWN)





Ref. No.

154

155

0 156

157

0 158

159

0 C601

Part No.

Description

2-582-212-01 SCREW, TRIPOD

2-587-151-01 SCREW (M1.4), NEW TRUSTAR.P2

1-478-674-11 FLASH UNIT (Note)

2-582-204-01 SHEET, STROBOSCOPE INSULATING

1-864-113-11 FP-163 FLEXIBLE BOARD

2-590-582-01 SHEET, CAPACITOR INSULATING

1-100-969-11 CAP, ELECT 117uF 315V

(Note)

DSC-P200

5-5

CD-517 FP-161 FP-162 FP-163

5-2. ELECTRICAL PARTS LIST

Ref. No.

Part No.

Description

A-1089-498-A CCD BLOCK ASSY

(Not supplied) CD-517 FLEXIBLE BOARD, COMPLETE

*******************************

(CCD block assy is including CD-517 flexible board and IC101 (CCD imager).)

Ref. No.

Part No.

Description

< LINE FILTER >

LF101 1-456-681-21 COIL, CHOKE

0

< CAPACITOR >

1-864-113-11 FP-163 FLEXIBLE BOARD

*********************

(FLASH UNIT and C601 are not included in this flexible board.) C102 1-107-826-11 CERAMIC CHIP 0.1uF

C105 1-107-826-11 CERAMIC CHIP 0.1uF

C106 1-107-826-11 CERAMIC CHIP 0.1uF

C107 1-107-826-11 CERAMIC CHIP 0.1uF

10% 16V

10% 16V

10% 16V

10% 16V

0

1-478-674-11 FLASH UNIT

< CAPACITOR >

< DIODE >

0 C601

1-100-969-11 CAP, ELECT 117uF 315V

D101 8-719-077-34 DIODE SML-310YTT86 (FLASH/CHG)

D103 8-719-075-29 DIODE SML-510MWT86S (AE/AF LOCK)

D104 6-500-505-01 DIODE OPY5052

(SELF TIMER/AF ILLUMINATOR)

< IC >

Electrical parts list of the CH-146 and SY-

123 boards are not shown.

Pages 5-7 to 5-11 are not shown.

IC101 (Not supplied) ICX489CQZ-13 (Note)

< TRANSISTOR >

Q101

Q102

Q103

6-550-119-01 TRANSISTOR



< RESISTOR >

DTC144EMT2L

DTC144EMT2L

2SC4250 (T5LSONY1)

R101 1-218-935-11 RES-CHIP

R102 1-218-966-11 RES-CHIP

R103 1-218-958-11 RES-CHIP

R104 1-218-954-11 RES-CHIP

R105 1-218-955-11 RES-CHIP

R109 1-218-990-11 SHORT CHIP

33

12K

2.7K

1.2K

1.5K

0

5%

5%

5%

5%

5%

1/16W

1/16W

1/16W

1/16W

1/16W

1-819-094-11 CONNECTOR, MEMORY STICK 10P

(Not supplied) FP-161 FLEXIBLE BOARD

****************************

(Memory stick connector is including FP-161 flexible board.)

0

A-1086-398-A FP-162 FLEXIBLE BOARD, COMPLETE

******************************

(This flexible complete board is including

CN101 (multi connector).)

0 BT901

1-780-141-21 BATTERY TERMINAL BOARD

< CONNECTOR >

CN101 (Not supplied) CONNECTOR, MULTIPLE (SOCKET)

< DIODE >

D101 8-719-056-23 DIODE MA2S111-(K8).SO

0 J101

< JACK >

1-817-331-11 DC JACK 5P (DC IN)

DSC-P200

5-6

(Note) Be sure to read “Precautions for Replacement of

CCD Imager” on page 4-8 when changing the

CCD imager.





Checking supplied accessories.

Power cord (1)

0

1-769-608-31 (AEP, E)

0

1-782-476-13 (CH)

0

1-783-374-12 (UK, HK)

0

1-790-107-22 (US, CND)

0 1-790-732-12 (JE)

0

1-823-947-12 (KR)

0

1-827-945-12 (AUS)

NP-FR1 battery pack (1)

(not supplied)

USB, AV cable for multi-use terminal (1)

1-829-866-11

Conversion adaptor (1)

0

1-569-007-11 (E, JE)

AC adaptor

AC-LS5/LS5B (1)

0

1-477-730-51

Wrist strap (1)

2-050-981-01

"Memory Stick" (32MB) (1)

(not supplied)

CD-ROM

(Cyber-shot application software) (1)

2-583-852-01 (US)

2-583-853-01

(CND, AEP, UK, E, HK, KR, AUS, JE)

2-583-854-01 (CH)


0

1-569-008-21 (E)

Battery case (1)

(not supplied)

Other accessories

2-582-853-11 INSTRUCTION (READ THIS FIRST) (ENGLISH)

(EXCEPT AEP, KR, CH)

2-582-853-21 INSTRUCTION (READ THIS FIRST)

(FRENCH, ITALIAN) (CND, AEP)


(SPANISH, PORTUGUESE) (AEP, E, JE)


(GERMAN, DUTCH) (AEP)


(TRADITIONAL CHINESE, SIMPLIFIED CHINESE)

(E, HK, CH, JE)


(RUSSIAN, SWEDISH) (AEP)


(ARABIC, PERSIAN) (E)

2-582-853-81 INSTRUCTION (READ THIS FIRST) (KOREAN)

(KR, JE)

2-582-853-91 INSTRUCTION (READ THIS FIRST) (POLISH, CZECH)

(AEP)


(HUNGARIAN, SLOVAKIAN) (AEP)

2-582-856-11 INSTRUCTION (USER’S GUIDE) (ENGLISH)

(EXCEPT AEP, AR, KR, BR, CH)

2-582-856-21 INSTRUCTION (USER’S GUIDE) (FRENCH, ITALIAN)

(CND, AEP)

2-582-856-31 INSTRUCTION (USER’S GUIDE)

(SPANISH, PORTUGUESE) (AEP, E, JE)

2-582-856-41 INSTRUCTION (USER’S GUIDE) (GERMAN, DUTCH)

(AEP)



(E, HK, CH, JE)



2-582-856-71 INSTRUCTION (USER’S GUIDE) (ARABIC, PERSIAN)

(E)

2-582-856-81 INSTRUCTION (USER’S GUIDE) (KOREAN) (KR, JE)

2-582-856-91 INSTRUCTION (USER’S GUIDE) (POLISH, CZECH)

(AEP)







DSC-P200

5-12E

SERVICE MANUAL

Ver 1.1 2005.02

DSC-P200

SUPPLEMENT-1

File this supplement with the service manual.

(PV04-027)

LEVEL

2

US Model

Canadian Model

AEP Model

UK Model

E Model

Hong Kong Model

Australian Model

Chinese Model

Korea Model

Argentine Model

Brazilian Model

Tourist Model

• Addition of Red Model

• Change of Repair Parts

• Addition of Argentine and Brazilian Models

•

Addition of Red Model

This supplement covers only differences from models other than red.

Refer to the parts list of original service manual about other parts.


Page

5-2

Red model

Ref. No.

Part No.

2

9

10

Description

2-547-039-11 CABINET (FRONT (K)) (RED)

A-1110-132-A CABINET (REAR) BLOCK ASSY (RED)

X-2055-298-1 CABINET ASSY, SIDE (RED)

5-5

151 X-2055-277-1 HOLDER ASSY, BATTERY (RED)

152 2-547-035-31 LID, DC JACK (RED)

153 2-547-036-31 LID, BATTERY (RED)

DSC-P200

9-876-854-82

Sony EMCS Co.

2005B0500-1

© 2005.2


•

Change of Repair Parts

•

Addition of Argentine and Brazilian Models


&

: Points added portion.

: Points changed portion.

Page

5-2

Former

Ref. No.

Part No.

1

Description

2-547-040-01 RING, LENS

5-4

102 A-1107-528-A SY-123 BOARD, COMPLETE (SERVICE)

(including CP101 (CH-146 board) and

IC301 (KWF board)) (E)

New

Description Ref. No.

Part No.

1 2-547-040-02 RING, LENS

[


(including CP101 (CH-146 board) and

IC301 (KWF board)) (E, AR, BR)

)

•

Abbreviation

AR : Argentine model


DSC-P200

— 2 —

&



!

: Points deleted portion.


Power cord (1)

0 1-769-608-31 (AEP, E)

0

1-782-476-13 (CH)

0

1-783-374-12 (UK, HK)

0

1-790-107-22 (US, CND)

0

1-790-732-12 (JE)

0 1-823-947-12 (KR)

0

1-827-945-12 (AUS)

0

1-783-952-11 (AR)

*


(not supplied)


1-829-866-11

CD-ROM


2-583-852-01 (US)

2-583-853-01


0

1-569-007-11 (E, JE)

AC adaptor

AC-LS5/LS5B (1)

0

1-477-730-71

[

Wrist strap (1)

2-050-981-01


(not supplied)


0

1-569-008-21 (E)

(CND, AEP, UK, E, HK, KR, AUS, AR, BR, CH, JE)

2-583-854-01 (CH)

$

)

Battery case (1)

(not supplied)







(SPANISH, PORTUGUESE) (AEP, E, AR, JE)

)





(E, HK, CH, JE)






(KR, JE)


(AEP)






(CND, AEP)




)

(AEP)



(E, HK, CH, JE)




(E)



(AEP)



•

Abbreviation




CH : Chinese model



JE : Tourist model

KR : Korean model





DSC-P200

— 3 —

SERVICE MANUAL

Ver 1.2 2005.05

DSC-P200

SUPPLEMENT-2

File this supplement with the service manual.

(PV04-030)

LEVEL

2

US Model

Canadian Model

AEP Model

UK Model

E Model

Hong Kong Model

Australian Model

Chinese Model

Korea Model

Argentine Model

Brazilian Model

Tourist Model

Japanese Model

• Addition of Japanese Model

•

Addition of Japanese Model

This supplement covers only differences from models other than Japanese.

Refer to the parts list of original service manual about other parts.

DSC-P200

9-876-854-85

Sony EMCS Co.

2005E0500-1

© 2005.5


•

Language that can be selected about SY-123 board

GP1 J

GP2

US

CND

AUS

Vietnam

GP3

GP4

GP5

AEP

UK

E

AR

BR

TW

JE

HK

CH

KR z z z z z z z z z z z z z

&


: Points deleted portion.

z z z z z z z z z z z z z z z


Page Former New

108

(Note 2)

108

(Note 2)

106 106

110

ns

109

#

110

ns

109

112 112

5-4 Ref. No.

Part No.

Description


(including CP101 (CH-146 board) and IC301 (KWF board)) (E, AR, BR)


(including CP101 (CH-146 board) and IC301 (KWF board)) (HK, KR, CH, JE)


(including CP101 (CH-146 board) and IC301 (KWF board)) (US, CND, AUS)


(including CP101 (CH-146 board) and IC301 (KWF board)) (AEP, UK)

110 2-590-642-01 SHEET, SY RADIATION

Ref. No.

Part No.

Description


&

(GP4) (including CP101 (CH-146 board) and IC301 (KWF board)) (E, AR, BR)


&

(GP5) (including CP101 (CH-146 board) and IC301 (KWF board)) (HK, KR, CH, JE)


&

(GP2) (including CP101 (CH-146 board) and IC301 (KWF board)) (US, CND, AUS)


&

(GP3) (including CP101 (CH-146 board) and IC301 (KWF board)) (AEP, UK)


(GP1) (including CP101 (CH-146 board) and IC301 (KWF board) (J)

)

@

DSC-P200

— 2 —

&




Power cord (1)

0

1-782-476-13 (CH)

0

1-783-374-12 (UK, HK)

0

1-790-107-22 (US, CND)

0

1-790-732-12 (JE, J)

*

0

1-823-946-12 (AEP, E)

[

0

1-823-947-12 (KR)

0

1-827-945-12 (AUS)

0

1-783-952-11 (AR)


(not supplied)


1-829-866-11

]

CD-ROM


2-583-852-01 (US)

2-583-853-01

AC adaptor

AC-LS5/LS5B (1)

0

1-477-730-81

[

(CND, AEP, UK, E, HK, KR, AUS, AR, BR, CH, JE, J)

)


0

1-569-007-11 (E, JE)

Wrist strap (1)

2-050-981-01


(not supplied)


0

1-569-008-21 (E)

Battery case (1)

(not supplied)

•

Abbreviation




CH : Chinese model



J : Japanese model

JE : Tourist model

KR : Korean model












(E, HK, CH, JE)






(KR, JE)


(AEP)






(CND, AEP)




(AEP)



(E, HK, CH, JE)




(E)



(AEP)



2-634-580-01 INSTRUCTION (READ THIS FIRST) (JAPANESE) (J)

2-634-581-01 INSTRUCTION (USER’S GUIDE) (JAPANESE) (J)

)

)





DSC-P200

— 3 —

[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]

Toolbar

Printing a text

1. Click the Print button .

2. Specify a printer, print range, number of copies, and other options, and then click [OK].

Application of printing:

To set a range to be printed within a page, select the graphic selection tool and drag on the page to enclose a range to be printed, and then click the Print button.

Reversing the screens displayed once

• To reverse the previous screens (operation) one by one, click the .

• To advance the reversed screens (operation) one by one, click the .

Application to the Service Manual:

This function allows you to go and back between circuit diagram and printed circuit board diagram, and accordingly it will be convenient for the voltage check.

Finding a text

1. Click the Find button .

2. Enter a character string to be found into a text box, and click the [Find]. (Specify the find options as necessary)


To execute “find” from current page toward the previous pages, select the check box “Find Backward” and then click the

“Find”.

Moving with link

1. Select either palm tool , zoom tool , text selection tool

, or graphic selection tool .

2. Place the pointer in the position in a text where the link exists

(such as a button on cover and the table of contents page, or blue characters on the removal flowchart page or drawing page), and the pointer will change to the forefinger form

3. Then, click the link. (You will go to the link destination.)

.

Moving with bookmark:

Click an item (text) on the bookmark pallet, and you can move to the link destination. Also, clicking can display the hidden items.

(To go back to original state, click )

3. Open the find dialog box again, and click the [Find Again] and you can find the matched character strings displayed next.

(Character strings entered previously are displayed as they are in the text box.)


The parts on the drawing pages (block diagrams, circuit diagrams, printed circuit boards) and parts list pages in a text can be found using this find function. For example, find a

Ref. No. of IC on the block diagram, and click the [Find Again] continuously, so that you can move to the Ref. No. of IC on the circuit diagram or printed circuit board diagram successively.

Note:

The find function may not be applied to the Service

Manual depending on the date of issue.

Zooming or rotating the screen display

“Zoom in/out”

• Click the triangle button in the zoom control box to select the display magnification. Or, you may click or for zooming in or out.

Switching a page

• To move to the first page, click the .

• To move to the last page, click the .

• To move to the previous page, click the .

• To move to the next page, click the .

“Rotate”

• Click rotate tool , and the page then rotates 90 degrees each.


The printed circuit board diagram you see now can be changed to the same direction as the set.

Reverse

987685433.pdf

Revision History

Ver.

1.0

1.1

1.2

Date

2005.01

2005.02

History

Official Release

Supplement-1

(S1 PV04-027)

2005.05

Supplement-2

(S2 PV04-030)

Contents

—

• Addition of Red Model

• Change of Repair Parts

• Addition of Argentine and Brazilian Models

• Addition of Japanese Model

S.M. Rev.

issued

—

No

No

DSC-P200

Sony DSC-P200 P200 camera SERVICE MANUAL

Assistant Bot

LEVEL

US Model

Canadian Model

AEP Model

UK Model

E Model

Hong Kong Model

Australian Model

Chinese Model

Korea Model

Argentine Model

Brazilian Model

Tourist Model

Japanese Model

• Reference No. search on printed wiring boards is available.

• Note in Lens Frame Installation

• Exchange Method of Barrier Assy

Sony EMCS Co.

SAFETY CHECK-OUT

1. SERVICE NOTE

1-1. NOTE FOR REPAIR

1-2. DISCHARGING OF THE FP-163

FLEXIBLE BOARD’S CHARGING

CAPACITOR (C601)

1-3. NOTE IN LENS FRAME INSTALLATION

1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY

2. DISASSEMBLY

2-1. DISASSEMBLY

2-2. SY-123 BOARD SERVICE POSITION

2-3. EXCHANGE METHOD OF BARRIER ASSY

2-4. CIRCUIT BOARDS LOCATION

Control switch block

SY-123

(including CP101

(CH-146 board) and IC301

(KFW board))

Control SW block

(SW51740)

FP-163 flexible

CD-517 flexible

FP-162 flexible

CH-146

(included in SY-123)

FP-161 flexible

(included in Memory stick connector)

CD-517 flexible

CH-146

CCD IMAGER

CCD SIGNAL PROCESS

(included in SY-123)

FP-161 flexible

(included in Memory

MEMORY STICK CONNECTOR stick connector)

FP-162 flexible

FP-163 flexible

SY-123

DC IN, MULTI CONNECTOR

FLASH

CAMERA MODULE, CAMERA DSP, LENS DRIVE,

(including CP-101 SH DSP, FRONT CONTROL, LCD DRIVE, AUDIO,

( CH-146 board) and DC/DC CONVERTER, CONNECTOR

IC301 (KWF board))

3. BLOCK DIAGRAMS

3. BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/2)

3-2. OVERALL BLOCK DIAGRAM (2/2)

3-3. POWER BLOCK DIAGRAM (1/2)

3-4. POWER BLOCK DIAGRAM (2/2)

4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM

FRAME SCHEMATIC DIAGRAM

FP-163

FLEXIBLE

BOARD

CONTROL SWITCH

BLOCK(RL)

CONTROL

SWITCH