EBN Solid POS 70 Series Service manual
advertisement
S e r v i i c e M a n u a l l
M a r c h 2 0
0
7
S o l l i i d P O S 7 0
S e r i i e s
*
P O S 7 0 1 2 E G 3 7 0
*
P O S 7 0 1 5 E G 3 7 0
1/84 Rev. 1.1
Contents
2/84 Rev. 1.1
3/84 Rev. 1.1
1 Chapter 1 : Troubleshooting
1.1 Symptoms and Solutions
Error Code Symptom Check Points
1001
1003
NO BOOT with
1.RAM
2.CPU
Power On
3.MB(2.3.1)
1. Power cord
2. Power button board (2.3.5)
3. Power button
4. MB (2.3.1)
5.Power
Supply(2.2.3)
System HANG
1.RAM
2.CPU
Up
3.MB(2.3.1)
Detail Steps
1. Check LED Light (Upper Left) should be on
2. If yes to item 1, open upper case, check if RAM well plugged on the memory slot
3. Check golden finger cleanness, if not clean, use pencil eraser to clean golden finger
4. If still fail, replace with another RAM for testing
5. If fail, replace with another CPU for testing
6. If fail, replace with another mother board for testing
7. If fail, RMA system to manufacturer
1. Check Power Cord is well plugged or not
2. If yes to item 1, open upper case, check if power button damaged, if yes, replace with another power button board (POS
75) or replace with another MB(POS 72)
3. If power button not damaged, check if power button cable to
MB well plugged.
4. If fail, replace with another power button cable
5. If fail, replace with another MB(POS 75) for testing
6. If fail, replace with another power supply for testing
7. If fail, System RMA to manufacturer
1. Check golden finger cleanness, if not clean, use pencil eraser to clean golden finger
2. If still fail, replace with another RAM for testing
3. If fail, replace with another CPU for testing
4. If fail, replace with another mother board for testing
5. If fail, System RMA to manufacturer
1.Bridge Board to
LCD Cable(2.3.7.9)
(2.3.2)
3.MB(2.3.1)
1. Shut Down Power
2. Open upper case, check cable between bridge board and LCD well connected or not. Replace with another LCD cable for testing
3. If fail, replace with another bridge board
4. If fail, replace with another mother board
5. If fail, System RMA to manufacturer
4/84 Rev. 1.1
Error Code Symptom
1005
1007
LCD Turn
Black
Check Points
1. Inverter to LCD cable,
2. Inverter to MB cable, (2.3.7.1)
3. Inverter board
4. MB(2.3.1)
5. LCD(2.1.3)
Detail Steps
1. Shut down power
2. Open upper case, check cable between inverter and LCD well connected or not.
4. If fail, check cable between inverter and mother board well connected or not. Replace with another inverter and MB cable for testing
5. If fail, replace with another inverter board for testing
6. If fail, replace with another mother board for testing
7. If fail, System RMA to manufacturer
Error Message:
CMOS checksum error
1. HDD (2.5.2)
2. HDD Cable
(2.3.7.5)
3. MB(2.3.1)
1. On Board
Battery(2.3.6)
2. MB(2.3.1)
1. Shut down power
2. Open HDD Cover, check HDD 80pin cable and HDD power cable well connected or not
3. If fail, replace with another HDD for testing
4. If fail, open upper case, check cable between HDD and
Mother board well connected or not
5. If fail, replace with another mother board for testing
6. If fail, system RMA to manufacturer
1. Shut down power
2. Open upper case, check on board battery well connected / damage or not
3. If fail, replace with another battery
4. If fail, replace with another mother board
5. If fail, system RMA to manufacturer
1. Reinstall touch driver, working mode select "PnP"
2. If fail, shut down power
3. Open upper case, check if cable between touch panel and touch control board well connected.(Replace the cable with
1. Driver (NA)
2. Control board to touch panel at item 10)
4. If fail, check if cable between touch control board and MB well
MB cable (2.3.7.2) connected. Replace with another touch control board to MB cable board(2.3.4)
5. Check if switch (# 3) on touch control board at "On" position
4.MB(2.3.1)
5.Touch panel(2.1.2)
6. If fail, check M/B JP10 jumper setting to 2-3
7. If fail, replace with another touch control board
8. If fail, replace with another M/B for testing
9. Replace with another touch panel for testing
10. RMA system to manufacturer
5/84 Rev. 1.1
Error Code Symptom
1009
1010
1012
Boot Up K/B
Malfunction
PS/2 Mouse
Fail
Fail
1.100PIN Cable
2.MB(2.3.1)
1.100PIN Cable
2.MB(2.3.1)
COM Port Fail
1. Jumper setting
2. 100PIN cable
3. MB(2.3.1)
Fail
Check Points
1. MSR to MB
Cable(2.5.4)
2. MB(2.3.1)
1. Device Check
2. USB cable
3. MB(2.3.1)
Detail Steps
1. Shut down power
2. Check keyboard cable connection
3. If fail, replace with another keyboard for testing
4. If fail, open upper case, check 100 pin cable between IO board and MB well connected or not
5. If fail, replace with another MB for testing
6. If fail, system RMA to manufacturer
1. Shut down power
2. Check mouse cable connection
3. If fail, replace with another mouse
4. If fail, open upper case, check 100 pin cable between IO board and MB well connected or not
5. Replace with another MB for testing
6. If fail, system RMA to manufacturer
1. Shut down power
2. Open upper case, check if MSR cable goes underneath inverter and well connected to MB location (CN12). Note: the cable must go through EMI chassis breach
3. If fail, replace with another MSR
4. If fail, RMA MSR to manufacturer
1. Shut down power
2. Move to Bottom side, open jumper setting cover, check if jumper setting same with default setting chart. Note: If device connector is with voltage, jumper setting needs to change to 5V or 12V based on different device definition
3. If fail, open upper case, check 100pin cable to MB well connected or not
4. If fail, replace with another MB for testing
5. If fail, RMA system to manufacturer
1. Shut down power
2. Check device cable to USB port well connected or not
3. If fail, replace with another device
4. If fail, open upper case, check USB Cable to MB location
(CN11) well connected or not
5. If fail, replace with another MB for testing
6. If fail, RMA system to manufacturer
6/84 Rev. 1.1
1.2 BIOS Upgrade
1. Boot the system with a bootable floppy disk
a. A Windows 98/ME startup disk can be used
b.Or you can create an MS-DOS startup disk under Windows XP, to create an MS-DOS startup disk under
Windows XP, right click on the 3 ½ floppy drive icon under my computer and select format. On the format
dialog box, check the box next to “Create MS-DOS startup disk” and then click the start button to make a
MS-DOS startup disk..
2. Once you boot off of the bootable floppy disk, replace the bootable floppy disk with the floppy disk containing
the bios files.
3. To update the BIOS using the example above you would type the following command.
a. A:\F82744 s171r21.rom, then push the enter key.
F82744.exe = BIOS FLASH UTILITY
b. Follow the onscreen prompts to update the BIOS.
4. DO NOT TURN OFF THE POWER or RESET/REBOOT the SYSTEM before the BIOS update is completed, stopping the BIOS UPATE before it is completed will cause the system to become non-functional.
7/84 Rev. 1.1
5. Reboot the system once the bios update has been completed.
Note:
The BIOS contained here are exclusively for POS72/75 only. manufacturer assumes no responsibility for any
damages resulting from improper use or lack of technical expertise.
8/84 Rev. 1.1
2 Chapter 2 : Disassembly , Assembly
2.1 Main Unit
2.1.1 Front Bezel + Sponge Bezel
Item Photo
1
Description
1. Use screw driver to open upper case.
2. 2 screws needs to be removed
2
3
4
1. Remove 2 screws
2. Remove cover bracket
2
3
1
1. Remove 2 screws from MSR cover
2. Remove 2 screws from inverter
3. Remove 3 cables from inverter
1. Remove 4 screws
9/84 Rev. 1.1
Item Photo
5
Description
1. Separate front and back cover
6 1. Remove 12 screws
2. Remove speaker tape
7 1. Turn to front side
2. Remove and replace with another front bezel
2.1.2 Touch Panel + Touch Screen Holder
Item Photo
1
Description
1. Follow 2.1.1 item 1 to 7 turn to
Front side and remove front bezel
2. Remove 3 screws
10/84 Rev. 1.1
Item Photo
2
Description
1. Turn to back side and remove tape
3 1. Turn to front side and remove touch panel module
2. Replace with another touch panel module
11/84 Rev. 1.1
2.1.3 LCD, AUO 15” 1024 x 768
Item Photo
1
Description
1. Follow 2.1.2 item 1 to item 3 (action
1)
2. Turn to back side
3. Remove 4 screws
2 1. Cut plastic string
3
4
1
1
1
2
2
1. Remove 2 inverter cables
2. Remove LCD cable from LCD chassis
3. Remove LCD chassis
1. Remove tape
2. Remove LCD cable
12/84 Rev. 1.1
Item Photo
5
Description
1. Remove 2 screws from left LCD holder
2. Remove 2 screws from right LCD holder
3. Remove and replace with another
LCD
2.1.4 MSR (Refer to 2.5.4)
2.1.5 Mother Board (Refer to 2.3)
13/84 Rev. 1.1
2.1.6 EMI Chassis
Item Photo
1
Description
1. Remove 2 screws
2 1. Open upper case
2. Remove 7 screws
3 1. Remove and replace another EMI chassis
14/84 Rev. 1.1
2.1.7 Key Lock Set
Item Photo
1
Description
1. Follow 2.1.6 item 1 to 3 remove
EMI chassis
2 1. Remove 2 screws
2. Remove cover bracket
3
4
1. Remove 2 antennas
2. Remove tape
1. Remove 4 screws
15/84 Rev. 1.1
Item Photo
5
Description
1. Separate front cover from back cover
6 1. Remove 4 screws from hinge
7 1. Set upper case vertically
2. Remove back hinge cover
2
1
8 1. Set upper case horizontally
2. Remove front hinge cover
1
2
16/84 Rev. 1.1
Item Photo
9
Description
1. Remove 3 screws at left hinge
2. Remove 3 screws at right hinge
10 1. Separate upper case from bottom case
2. Pull out cables from upper case
11 1.Remove and replace with another key lock set (W/ LCD Hinge Assembly /
LCD Base)
17/84 Rev. 1.1
2.2 Base Unit
2.2.1 Base Housing
Item Photo
1
Description
1. Remove 4 screws from hinge front side
2 1. Set upper case vertically
2. Remove back hinge cover
3
2
1
4
1. Set top upper case horizontally
2. Remove front hinge cover
1. Remove 3 screws at left hinge
2. Remove 3 screws at right hinge
18/84 Rev. 1.1
Item Photo
5
Description
1. Separate upper case from bottom case
2. Pull out cables from upper case
6
7
1. Turn the bottom case to the bottom side
2. Remove 2 screws to take off the kit cover
1. Turn the bottom case top side
2. Take off kit cover
8 1. Turn the bottom case to the bottom side
2. Remove 4 screws
3. Remove 4 Plastic foot
19/84 Rev. 1.1
Item Photo
9
Description
1. Turn to the rear side of the bottom case
2. Remove 2 screws to open the HDD cover
10 1. Remove and replace with another base housing from base chassis
20/84 Rev. 1.1
2.2.2 Swivel Housing Rear / Front
Item Photo
1
Description
1. Remove 4 screws from hinge
2
1
3
2
1
2
1. Set upper case vertically
2. Remove back hinge cover
1. Set upper case horizontally
2. Remove front hinge cover
21/84 Rev. 1.1
2.2.3 P/S 220W W/PFC
Item Photo
1
2
3
Description
1. Follow 2.2.1 item 1 to 10
(Remove base housing)
2. Remove power cable
3. Remove HDD to M/B cable
4. Pull out HDD tray
2 1. Turn to bottom side and remove 6 screws
3 1. Turn to top side
2. HDD cable is tied with another black magic sticker separately
4 1. Remove black magic sticker used for HDD cable
2. Remove HDD cable
2
1
22/84 Rev. 1.1
Item Photo
5
Description
1. Separate swivel hinge from base chassis
6
7
8
2
2
1
2
1. Remove black magic sticker used for tightening cables
2. Pull out cables from swivel hinge one by one
1
1. Remove power cable which connects PSU and I/O Board
2. Remove 2 tapes
1. Remove black connector together with cables from power supply
23/84 Rev. 1.1
Item Photo
9
Description
1. Pay attention to the position for cable
10
11
1. Remove 3 screws
1. Pull up from the hooker and pull to left direction to remove power supply
2. Replace with another power supply
24/84 Rev. 1.1
2.2.4 I/O Board
Item Photo
1
5
2
4
3
Description
1. Follow 2.2.3 item 1 to 6
2. Remove USB Cable
3. Remove Power supply to I/O board cable
4. Remove 100pin cable
5. Remove power supply to AC input cable
2 1. For USB cable, need to remove 1 screw from I/O board
3 1. Turn to bottom side
2. Remove 2 screws
4 1. Remove power supply module from base chassis
25/84 Rev. 1.1
Item Photo
5
Description
1. Remove 12 screws
6
2.2.5 HDD / HDD Tray (Refer to 2.5.2)
1. Remove 4 screws on I/O board
2. Remove and replace with another
I/O board
3. Follow steps back to item 1 for assembly
26/84 Rev. 1.1
2.2.6 Jumper Cover
Item Photo
1
Description
1. Turn the bottom case to the bottom side
2. Remove 1 screw
3. Remove and replace with another jumper cover
27/84 Rev. 1.1
2.3 Boards
2.3.1 Main Board
Item Photo
1
Description
1. Use screw driver to open upper case.
2. Remove 2 screws
2 1. Remove 2 screws
2. Remove cover bracket
3
9
3
6
5
4
8
7
2
1
1. Remove Cables, M/B To Inverter
2. Remove Cables, M/B To Touch
Control Board
3. Remove Cables, M/B To Speaker
4. Remove Cables, M/B To I/O BD
100P
5. Remove Cables, M/B To HDD 80P
6. Remove Cables, 2 nd
VGA 10P
7. Remove Cables, M/B To I/O BD
20P USB
8. Remove Cable, M/B To Power
Supply
9. Remove Mini PCI
28/84 Rev. 1.1
Item Photo
4
1
Description
1. Remove Inverter Cable on top
2. Remove Inverter Cable bottom
5
2
1. Remove 2 screws on bridge board
6 1. Remove bridge board
7 1. Remove 6 screws on M/B
2. Remove 2 銅柱
29/84 Rev. 1.1
Item Photo
8
Description
1. Remove and replace with another
M/B
2.3.2 Bridge Board
Item Photo
1
Description
1. Follow 2.3.1 item 1
2. Open upper case
3. Remove VGA cable from bridge board
4. Remove 2 screws on bridge board
2 1. Remove and replace another bridge board
30/84 Rev. 1.1
2.3.3 Inverter
Item Photo
1
Description
1. Follow 2.3.1 item 1
2. Remove 3 cables
3. Remove 2 screws
2 1. Remove and replace with another inverter board
31/84 Rev. 1.1
2.3.4 Touch Control Board
Item Photo
1
Description
1. Follow 2.3.3 item 1 to 2 remove inverter board
2. Remove cable from touch control board
3. Remove 4 screws
2 1. Push out black clicker from connector CN2
3 1. Remove touch control board
2. Pull out touch panel cable
3. Replace with anther touch control board
32/84 Rev. 1.1
2.3.5 Button Board (For POS 75)
Item Photo
1
Description
1. Follow 2.3.1 item 1
2. Open upper case
2
3
1. Remove cable from button board
2. Remove 2 screws
1. Remove and replace with another button board
33/84 Rev. 1.1
2.4 Cables
2.4.1 Cable, M/B To Inverter
Item Photo
1
Description
Part Number: 21600003RH
2 1. Use screw driver to open upper case.
2. Remove 2 screws
3
2
1
1. Remove cable on MB location
CN17
2. Remove cable on inverter board
3. Replace with another inverter cable
34/84 Rev. 1.1
2.4.2 Cable, M/B To Touch Control BD
Item Photo
1
Description
1. Part Number: 21600004RH
2
3
1. Use screw driver to open upper case.
2. Remove 2 screws
1. Remove 3 cables
2. Remove 2 screws
4 1. Remove inverter board
35/84 Rev. 1.1
Item Photo
5
Description
1. Remove and replace with another
Touch Control board cable (Main
Board Location CN 17)
2. Follow steps back to item 1 for assembly
36/84 Rev. 1.1
2.4.3 Cable, M/B To Speaker
Item Photo
1
Description
Part Number: 21600006RH
2 1. Follow 2.1.1 item 1 to 7 turn to
Front side and remove front bezel
3
1
1. Turn to back side and remove cable on MB location CN 14
2. Remove black tape
4
2
2
1. Remove 2 screws on left speaker
2. Remove 2 screws on right speaker
3. Replace with another speaker cable
4. Follow steps back to item 1
1
37/84 Rev. 1.1
2.4.4 Cable, M/B To I/O BD 100P
Item Photo
1
Description
1. Part Number: 21600007RH
2
3
1. Follow 2.1.7 item 1 to 9 to disassemble upper case
2. Follow 2.2.1 item 1 to 10 to disassemble base unit
3. Follow 2.2.3 item 1 to 7 to remove tapes and power supply cable
4. Remove black magic sticker
5. Pull out cables from swivel hinge one by one
1. Remove and replace cable on IO
Board Location CN2
2. Follow steps back to item 1 for assembly
38/84 Rev. 1.1
2.4.5 Cable, M/B To HDD 80P
Item Photo
1
Description
Part Number: 21600008RH
2 1. Follow 2.2.1 item 1 to 10 to disassemble base unit
2. Remove and replace with another
HDD cable
3. Follow steps back to item 1 for assembly
2.4.6 Cable, 2nd VGA to I/O Board
Item Photo
1
Description
Part Number: 21600009RH
Location on M/B CN5
2 1. Follow 2.1.7 item 1 to 9 to disassemble upper case
2. Follow 2.2.1 item 1 to 10 to disassemble base unit
3. Follow 2.2.3 item 1 to 7
4. Remove black magic sticker
5. Pull out cables from swivel hinge one by one
39/84 Rev. 1.1
Item Photo
3
3
1
2
Description
1. Remove 2 screws from front side to disassemble VGA connector
2. Remove power cable from IO board
3. Remove power cable
4 1. Remove black tape
5 1. Remove black tape
2. Remove fan cable
2
6 1. Remove screw from USB cable
2. Remove USB cable connector in order to take off AC Inlet To P/S cable
3. Replace with another AC Inlet To
P/S cable
4. Follow steps back to item 1 for assembly
40/84 Rev. 1.1
2.4.7 Cable, M/B To I/O BD 20P USB
Item Photo
1
Description
Part Number: 21600016
MB Location CN11
2
3
2.4.8 Cable, M/B To Button Board
Item Photo
1
1. Follow 2.1.7 item 1 to 9 to disassemble upper case
2. Follow 2.2.1 item 1 to 10 to disassemble base unit
3. Follow 2.2.3 item 1 to 7
4. Remove black magic sticker
5. Pull out cables from swivel hinge one by one
1. Remove screw from IO Board
2. Remove and replace another USB cable
3. Follow steps back to item 1 for assembly
Description
1. Follow 2.3.1 item 1
2. Open upper case
3. Remove and Replace with another
M/B to Button board cable
41/84 Rev. 1.1
2.4.9 Cable, LCD to Bridge Board
Item Photo
1
Description
1 Part No.:21600005RH
2
3
1. Follow 2.1.2 item 1 to item 3 remove touch panel
2. Turn to back side
3. Remove 4 screws
1
1. Cut plastic string
4
2
1. Remove 2 inverter cables
2. Remove LCD cable from bridge board
1
42/84 Rev. 1.1
Item Photo
5
Description
1. Remove LCD chassis
6
1
2
1. Remove tape
2. Remove and replace with another
LCD cable
3. Follow steps back to item 1 for assembly
43/84 Rev. 1.1
2.5 Main & Base Unit assembly
Item Photo
1
Description
1. Prepare upper and base unit
2
3
4
1. Put upper unit on the swivel hinge
1. Fasten 3 screws on the left side of neck
2. Fasten 3 screws on the right side of neck
1. Put cables through upper case hole
44/84 Rev. 1.1
Item Photo
5
Description
1. Cables must go through the hole at center of upper case
2. Connect cables to the MB
6 1. Tied cables with magic tape
2. Fasten cover bracket with 2 screws
7 1. Fasten EMI cover on the upper case with 7 screws
8 1. Put on the front cover W/O fastening screws.
45/84 Rev. 1.1
Item Photo
9
Description
1. Put swivel hinge back cover on case
10 1. Fasten 4 screws
46/84 Rev. 1.1
2.6 Accessories
2.6.1 HDD
Item Photo
1
Description
1. Follow 2.2.1 item 1 to 10 (Remove base housing)
2. Remove power cable
3. Remove HDD to M/B cable
4. Pull out HDD tray
2
3
2 1. Remove 2 screws from HDD left hand side
2. Remove 2 screws from HDD right hand side
3 1. Remove and replace with another
HDD
47/84 Rev. 1.1
2.6.2 Pole Display
Item Photo
1
Description
1. Packing List: a. Assembly（1 )Tube and（2 )VFD
Unit
1
2
1. Remove the customer display cover from rear base
1. Remove two screws marked in red
3 1. Install the VFD kit on rear base
48/84 Rev. 1.1
Item Photo
4
Description
1. Connect VFD cable to COM1 and screw up
5 1. Remove jumper cover, adjust Pin9
13-14 close for COM1 to be 12V
6
Verification
7
Verify the VFD through by Hyper
Terminal as following procedure.
Enter to “All Programs” Æ
“Communication” Æ “Hyper Terminal”
1. Click “Yes” to continue
49/84 Rev. 1.1
Item Photo
8
Description
1. Set “area code” and click OK
9 1. Select on using COM1 port.
1. Set on Baud Rate to be 9600 bps. 10
11 1. Press random character from keyboard which will be shown on VFD
50/84 Rev. 1.1
2.6.3 MSR
Item Photo
1
Description
1. 3 tracks MSR module (PS2)
1 1. Screw off the cover.
2
3
1. Pass through the MSR cable under the Inverter BD, connect to CN12 of
M/B
1. Screw up the module to the slot.
51/84 Rev. 1.1
1
Verification
2
1. Enter to “Accessories” Æ “Notepad”
1. Stripe the MSR card to Reader and complete test OK.
52/84 Rev. 1.1
1
2
3
2.6.4 MSR+ I Button
Item Photo
1
Description
1. 3 tracks MSR module (PS2)
1. Screw off the cover.
1. Pass through the MSR cable under the Inverter BD, connect to CN12 of
M/B
1. Screw up the MSR to slot.
53/84 Rev. 1.1
1
Verification
1. Enter to “Accessories” Æ “Notepad”
2
Card Reader
I-Button
Data
Complete test OK.
54/84 Rev. 1.1
2.6.5 MSR+ Smart Card
Item Photo
1
Description
1. MSR 3 tracks (Serial Port) + Smart
Card Reader module (USB)
1 1. Screw off the cover.
2
3
1. Pass through the cables under the
Inverter BD, connect to COM cable to
CN12 as red mark 1. Connect Smart cable to JP6 as red mark2.
1. Screw up the module to the slot
55/84 Rev. 1.1
1
Verification MSR
2
3
1. 1. Enter to” All Programs” Æ
“Communication” Æ “Hyper
Terminal”
2. b. Set the configuration as same to
VFD as above
1. Set on using COM5 port.
1. Set on Baud Rate to be 9600 bps.
4 1. Stripe the MSR card to Reader and complete test OK
56/84 Rev. 1.1
1
Smart Card Driver Installation and
Verification
1. Select “Yes, this time only” and
Click Next
2 1. Install the software automatically
[Recommended] and Click Next
3
4
1. Click Finish for complete installation
1. Enter to Smart Card Utility Æ
Select “SYN_PcSc_Test”
57/84 Rev. 1.1
Item Photo
5
Description
1. Select STD 200 0
6
7
1. Insert IC Card to slot
1. Show “PASS” complete test OK
58/84 Rev. 1.1
2.6.6 2nd Display W/ Touch
Item Photo
1
Description
1. 12.1 / 15” display with Fujitsu
Touch Panel
2. Cable 1: VGA with power pin
I/P.
Cable 2: Serial touch with power pin I/P.
1 1. Screw off the two screws as red mark.
2 1. Install the second display unit with POS70
59/84 Rev. 1.1
Item Photo
3
Description
1. Fasten the 2nd display with 6 screws as red mark. Connect cable 1 to VGA port and cable 2 to COM1
4 1. Remove the jumper cover, adjust
Pin1 21-22 close for COM1 to be
5V
1
Driver Installation and Verification
Driver Installation and Verification
1. Display Setup
2. Enter to “Control Panel”
2 1. Click “Display” icon
60/84 Rev. 1.1
Item Photo
3
Description
1. Set main display by “Settings” to
2.[Multiple Monitors ]…
4
5
1
Install Touch Driver
1. Select “Extend my Windows
Desktop onto this monitor on
VIA/S3G.
1. Click “Yes” for save the settings.
The 2nd display was shown out the extend the screen
1. Insert the Driver Bank disc to
CD ROMÆSelect “POS7
Series”
61/84 Rev. 1.1
Item Photo
2
Description
1. Select “Touch Driver”
3
4
1. Select “FUJITSU TOUCH
PANEL”
1. Select “Fujitsu Touch Panel
Driver (SERIAL Interface)”
5 1. Select “Non Plug and Play
Device” and click OK
62/84 Rev. 1.1
Item Photo
6
Description
1. Click OK for completed installation
7
8
1. Select dual port for touch by
COM1 and COM6
1. Completed installation ÆClick
“Yes” for restart system
9 1. Enter to “Control Panel”
63/84 Rev. 1.1
11
12
Item Photo
10
Description
1. Click “Touch Panel” icon
1. Select Dual monitor set-up
1. Select “Calibration” Æ
Connected port COM1 & COM6
64/84 Rev. 1.1
2
3
2.6.7 RFID
Item Photo
1
1
H/W Installation
Description
1. RFID module (Serial I/F)
1. Screw off the cover.
1. Pass through the RFID cable under the Inverter BD, connect to CN12 of
M/B
1. Screw up the RFID on the slot.
65/84 Rev. 1.1
2
3
4
1
Verification
1. Enter to” All Programs” Æ
“Communication” Æ “Hyper Terminal”
2. Set the configuration as same VFD as above
1. Set on using COM5 port.
1. Set on Baud Rate to be 9600 bps.
1. Attach the RFID card to Reader, completed test OK
66/84 Rev. 1.1
2.6.8 Compact Flash
Item Photo
1
Description
1. Compact Flash
2 1. Use screw driver to open upper case
2. Remove 2 screws
3 1. Remove 2 screws on bridge board
4 1. Take off plastic strings from the hook
2. Remove bottom cable
67/84 Rev. 1.1
Item Photo
5
Description
1. Put compact flash on socket
68/84 Rev. 1.1
2.6.9 Smart Card
Item Photo
1
Description
1. MSR 3 tracks (Serial Port) + Smart
Card Reader module (USB)
1 1. Screw off the cover.
2 1. Pass through the cables under the
Inverter BD. Connect Smart cable to
JP6 as red mark
3 1. Screw up the module to the slot
69/84 Rev. 1.1
1
Smart Card Driver Installation and
Verification
3. Select “Yes, this time only” and
Click Next
2 4. Install the software automatically
[Recommended] and Click Next
3 5. Click Finish for complete installation
4 6. Enter to Smart Card Utility Æ
Select “SYN_PcSc_Test”
70/84 Rev. 1.1
Item Photo
5
Description
7. Select STD 200 0
6
7
2.6.10 I Button
Item Photo
1
8. Insert IC Card to slot
9. Show “PASS” complete test OK
Description
1. PS2-I button module kit
71/84 Rev. 1.1
1
2
3
1. Screw off the cover.
1. Pass through the I-button under the
Inverter BD, connect to CN12 of M/B
1. Screw up the MSR to slot.
1
Verification
1. Enter to “Accessories” Æ “Notepad”
72/84 Rev. 1.1
Item Photo
2
Complete test OK.
Description
I-Button
Data
2.6.11 Mini PCI Wireless LAN
Item Photo
1
Description
Mini PCI Wireless LAN
2 1. Use screw driver to open upper case
2. Remove 2 screws
3 1. Insert the WLAN card to mini PCI slot
2. Connect the Antenna to card as red mark
73/84 Rev. 1.1
Item Photo
4
Description
1. Press Wireless LAN Card
2. Make sure connected well
5
6
1. Remove 2 screws from cover bracket
2. Remove cover bracket
3. Antenna cable needs to go under cover bracket
4. Remove EMI cover
1. Tied Antenna cable with other cables
7 1. Stick the Antenna by temped tape to back cover
74/84 Rev. 1.1
Item Photo
8
Description
1. Tighten 7 screws on EMI cover.
75/84 Rev. 1.1
3 Chapter 3 : Spare parts list
3.1 Main Unit
3.1.1 Explode of Main Unit
Item
3.1.2 Main Unit Parts list & quotation
Parts No. Description
15.0" Bezel PC+ABS 1CAV
1+2
1+2
3+5
10500004RH
10500025RH
A10400288RH
@Rubber Black +T4000, 310*2.4*1.5T
@Rubber Black +T4000, 238*2.4*1.5T
12.1" Bezel PC+ABS 1CAV
@ Rubber Black +T4000, 252*1.8*1T
@ Rubber Black +T4000, 195*1.8*1T
Fujitsu 15.0"touch panel
N010-0510-T237
Touch Screen Holder- 15.0"
@SPONG FOR POS70－15.0 312*5*1
@SPONG FOR POS70－15.0 245*5*1
Fujitsu 12.1"touch panel
3+5
A10400582RH
Touch Screen Holder-12.1” w/ Sponge
4
10500003RH
Square Speaker(Left and Right)
Speaker Cable
1
1
1
1
1
2
2
1
Q’ty
1
2
2
1
2
2
Price (US$)
Call Sales
Call Sales
Call Sales
Call Sales
Call Sales
76/84 Rev. 1.1
Item
6
6
7
7
8
9
10
11
Parts No. Description
21100014RH LCD, AUO 15” 1024 x 768, 350nits
21100001RH LCD, LG 12’1, 800*600, 300nits
30100017RH LCD Chassis-15.0(AUO)
30100010RH LCD Chassis-12.0 (LG)
30200007RH LED Lens, transparent
10100001RH Main Board,
10100004RH
FUJITSU Touch Panel Control
Board:N16B-0558-B280
10100007RH
Bridge Board-TTL, 18Bit+TTL (12.1”,
LG LCD)
11
12
13
14
15
16+17+1
8
16+17+1
8
10100006RH
Bridge Board-LVDS, 24Bit (15”, AUO
LCD)
22400012RH Inverter: 12.1/15.0", 8mA, RI1205-06G
30200015RH LCD BASE Cover, ABS, Black
30100003RH Cable Cover Bracket , 0.3T
30100120RH EMI Chassis
10500005RH
LCD Hinge Assembly
Key Pad
15” LCD Base
10500006RH
LCD Hinge Assembly
Key Pad
12.1” LCD Base
Q’ty Price (US$)
1 Call Sales
1 Call Sales
1 Call Sales
1 Call Sales
1 Call Sales
1 Call Sales
1
1
1
1
1
1
1 Call Sales
1 Call Sales
1 Call Sales
1 Call Sales
Call Sales
Call Sales
77/84 Rev. 1.1
3.2 Base Unit
3.2.1 Explode of Base Unit
78/84 Rev. 1.1
Item
1
2
3
4
5
7
8
9+10+
11
12
13
14
15
3.2.2 Base Unit Parts list & quotation
Parts No. Description
10500002RH
Swivel Front Cover, Black Sub-ASSY
10500001RH
10200004RH
A10400216RH
Swivel Rear Cover, Black Sub-ASSY
15”/12.1” Swivel Hinge Assembly
Power Supply Module:
1U, 220W, W/PFC
3.3 Cables
Part No. Description Photos
Q’ty Price (US$)
1
Call Sales
1 Call Sales
1
Call Sales
1 Call Sales
1 Call Sales
1 Call Sales
1
Call Sales
Call Sales
1
1 Call Sales
1 Call Sales
4 Call Sales
1 Call Sales
Price
21600003RH Cable, M/B To Inverter Call Sales
21600004RH
Cable, M/B To Touch Control
Board
Call Sales
21600006RH Cable, M/B To Speaker Call Sales
79/84 Rev. 1.1
Part No. Description
21600007RH Cable, M/B To I/O BD 100P
Photos Price (US$)
Call Sales
21600008RH
21600009RH
21600016RH
21600088RH
21600089RH
Cable, M/B To HDD 80P
Cable, 2 nd
VGA to I/O board
10 pin transfer to D-SUB 15 pins
Cable, M/B To I/O BD 20P
USB
POS-70 IDE Y CABLE
POS-70 HDD POWER Y
CABLE
Call Sales
Call Sales
Call Sales
Call Sales
Call Sales
80/84 Rev. 1.1
Part No. Description
21600002RH Cable for 24V Printer
3.4 Accessories
3.4.1 Power Cord
Part No. Description
POWER CORE FOR USA
20700001RH
POWER CORD FOR UK
20700005RH
POWER CORD FOR EUR
20700002RH
Photos
Photos
Price (US$)
Call Sales
Price (US$)
Call Sales
Call Sales
Call Sales
POWER CORD FOR
Australia
Call Sales
20700004RH
3.4.2 HDD
Part No.
20200009RH
Description
SEAGATE 5400RPM-40G
HDD ULTRA ATA/100
ST340015A
20200006RH 80G HDD WD 7200RPM
3.4.3 Pole Display
Part No. Description
Photos
Photos
Price (US$)
Call Sales
Call Sales
Price (US$)
81/84 Rev. 1.1
Call Sales
Call Sales
3.4.4 MSR
Part No.
A10400010RH
Description
2 Track : PS2
Photos Price (US$)
Call Sales
A10400023RH 2 Track : RS232
A10400009RH 3 Track : PS2
A10400024RH 3 Track : RS232
3.4.5 2nd Display
Part No. Description
A10400022RH 12” TFT LCD(w/o Touch)
Call Sales
Call Sales
Call Sales
A10400004RH 15” TFT LCD(w/o Touch)
A10400062RH
A10400107RH
12” TFT LCD(w/ Touch)
15” TFT LCD(w/ Touch)
NA
NA
Photos Price (US$)
Call Sales
Call Sales
Call Sales
Call Sales
82/84 Rev. 1.1
3.4.6 OS
Part No. Description
20900001RH
20900008RH
WinXP Professional Edition
Microsoft XP Home SP2, Chinese Ver.
20900002RH
3.4.7 RFID
WEPOS, English Ver.
Part No. Description Photos
Price (US$)
Call Sales
Call Sales
Call Sales
Call Sales
Price (US$)
A10400005RH RFID Call Sales
3.4.8 Compact Flash
Part No. Description
20600001RH Compact Flash 128MB
20600002RH
20600003RH
Compact Flash 256MB
Compact Flash 512MB
20600005RH Compact Flash 1G
3.4.9 Memory
Part No.
20300001RH
20300002RH
20300003RH
20300004RH
Memory: 128MB
Memory: 256MB
Memory: 512MB
Memory: 1G
Description
3.4.10 Smart Card +MSR 3T RS232
Part No. Description
Photos
Photos
Price (US$)
Call Sales
Call Sales
Call Sales
Call Sales
Price (US$)
Call Sales
Call Sales
Call Sales
Call Sales
Price (US$)
A10400104RH Smart Card +MSR 3T RS232 Call Sales
83/84 Rev. 1.1
3.4.11 I Button +MSR 2T KB
Part No. Description Photos Price (US$)
A10400121RH
3.4.12
Part No.
I Button +MSR 2T KB
Wireless LAN
Description
10100029RH
WIRELESS LAN 11g MINI
PCI MODULE
Call Sales
Photos Price (US$)
Call Sales
Call Sales
84/84 Rev. 1.1
advertisement
Related manuals
advertisement