user manual

user manual
P/N 35010033-A
user manual
Dimensions
All dimensions are in millimeters
©2012 Martin Professional A/S. Information subject to change without notice. Martin
Professional A/S and all affiliated companies disclaim liability for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss occasioned by the use of,
inability to use or reliance on the information contained in this manual. The Martin logo, the
Martin name and all other trademarks in this document pertaining to services or products by
Martin Professional A/S or its affiliates and subsidiaries are trademarks owned or licensed by
Martin Professional A/S or its affiliates or subsidiaries.
2
Dimensions
Contents
Dimensions ................................................................................................................................ 2
Contents..................................................................................................................................... 3
Safety information ...................................................................................................................... 4
Product overview ....................................................................................................................... 7
Product description ................................................................................................................ 7
Features at a glance ............................................................................................................... 7
Product details ....................................................................................................................... 8
Quick Start ................................................................................................................................. 9
Setting up ............................................................................................................................... 9
Making haze ........................................................................................................................... 9
Switching off ........................................................................................................................... 9
Installation and setting up ........................................................................................................ 10
Location ............................................................................................................................... 10
AC power.............................................................................................................................. 10
Setting up ............................................................................................................................. 11
Final checks ......................................................................................................................... 11
Turning on the power ........................................................................................................... 11
Turning off the power ........................................................................................................... 11
Control settings ........................................................................................................................ 13
Overview .............................................................................................................................. 13
Setting Run mode ................................................................................................................. 13
Setting Haze density ............................................................................................................. 13
Setting Fan speed ................................................................................................................ 14
Setting the Timer .................................................................................................................. 14
Setting the DMX base address ............................................................................................. 14
Setting the master-slave link mode ...................................................................................... 15
Alt option .............................................................................................................................. 15
Priming the machine after fluid out....................................................................................... 15
Resetting options to factory settings .................................................................................... 15
Remote control ........................................................................................................................ 17
Overview .............................................................................................................................. 17
Functions .............................................................................................................................. 17
Connection ........................................................................................................................... 17
DMX control ............................................................................................................................. 18
Overview .............................................................................................................................. 18
Connection ........................................................................................................................... 18
DMX functions ...................................................................................................................... 18
Haze fluid types........................................................................................................................ 20
Basic service ........................................................................................................................... 21
Cleaning ............................................................................................................................... 21
Fuse replacement................................................................................................................. 21
Troubleshooting ....................................................................................................................... 22
Status messages ...................................................................................................................... 23
Resetting the machine after fluid out.................................................................................... 23
Specifications .......................................................................................................................... 24
Contents
3
Safety information
The following symbols are used to identify important safety information:
Caution! Safety
hazard. Risk of
personal injury.
Caution! Burn
hazard. Hot
surface. Do not
touch.
Danger!
Hazardous
voltage. Contact
will cause electric
shock.
Caution! Fire
hazard.
Warning! This product is not for household use. It presents risks of injury due
to electric shock, burns, falls and respiratory problems!
Read this manual before operating the machine, follow the safety precautions
listed below, and observe all warnings in this manual and printed on the
machine. Use the system only as described in this manual and in accordance
with local laws and regulations.
If you have questions about how to operate the machine safely, or if you have
followed the instructions in this manual and the machine is malfunctioning,
please contact Martin Service.
Preventing electric shocks
4
•
Always ground (earth) the machine electrically.
•
Use only a source of AC power that complies with local building and
electrical codes, and that has both overload and ground-fault protection.
•
Before connecting the haze machine to power, check that the voltage
indicated on the machine’s serial label matches your local AC power
voltage. If your AC power voltage does not match, do not use the
machine. Contact Martin Service for assistance.
•
Before using the machine, check that all power distribution equipment
and cables are in perfect condition and rated for the current
requirements of all connected devices.
•
If the machine or any cables connected to it are in any way damaged,
defective, wet, or show signs of overheating, stop using the machine and
contact Martin Service for assistance. If the supply cord is damaged, it
must be replaced by a special cord or assembly available from the
manufacturer or its service agent.
•
Disconnect the machine from AC power before servicing and when not
in use.
•
This system is not waterproof and should not be exposed to wet outdoor
conditions. Do not immerse in water or any other liquid. Do not expose to
high-pressure water jets.
•
Do not spill fluid over or inside the machine. If fluid is spilled, disconnect
AC power and clean with a damp cloth. If fluid is spilled onto electronic
parts, take the system out of service and contact Martin for advice.
Safety information
•
Do not remove the covers or attempt to repair a faulty machine. Refer any
service not described in this manual to Martin.
•
Do not operate the machine if any parts are damaged, defective or
missing.
•
Moisture and electricity do not mix. Do not aim haze output at electrical
connections or devices.
Preventing burns and fire
•
The haze produced by the machine is hot enough to cause burns when it
leaves the nozzle, and very hot droplets of fluid escape occasionally.
Keep people and objects at least 60cm (24 inches) away from the haze
output nozzle.
•
Do not touch the haze output nozzle during or after use – it becomes
extremely hot and remains hot for several hours after the machine has
been shut down.
•
Haze output contains glycol, a flammable alcohol that burns with an
almost invisible blue flame. Do not point haze output at sources of
ignition such as open flames or pyrotechnic effects.
•
Do not attempt to bypass thermostatic switches, fluid sensors or fuses.
•
Replace fuses only with ones of the type and rating specified in this
manual for the machine.
•
Provide a minimum free space of 100mm (4 inches) around the machine.
•
Provide a minimum free space of 500mm (20 inches) around fans and air
vents and ensure free and unobstructed air flow to and around the
machine.
•
Keep the machine at least 60cm (24 inches) away from combustible and
heat-sensitive materials.
•
Do not operate the machine if the ambient temperature (Ta) is below 5°
C (41° F) or above 40° C (104° F).
•
Do not operate the machine if the relative air humidity exceeds 80%.
Preventing injuries
•
Ensure that the surface on which the machine is located or installed can
safely hold the weight of the machine.
•
Do not install the machine over areas where people are present.
•
This appliance is not intended for use by persons (including children)
with reduced physical sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
•
Haze machines can cause condensation. Do not point the output at
smooth floors. Floors and surfaces may become slippery. Check these
frequently and wipe dry as necessary to avoid any danger of slipping.
•
Ensure at least 2m visibility in areas where haze is being produced.
•
Haze fluid contains food-grade glycols in solution but may present health
risks if swallowed. Do not drink it. Store it securely. If eye contact occurs,
rinse with water. If fluid is swallowed, give water and obtain medical
advice.
Safety information
5
Preventing breathing problems
6
•
A haze machine can operate safely only with the haze fluid it is designed
for. Use the machine only with fluids specified under “Haze fluid options”
on page 20 or you may cause the release of toxic gases, presenting a
severe health hazard. You will also probably damage the machine.
•
Do not create dense haze in confined or poorly ventilated areas.
•
Do not expose people with health problems (including allergic and/or
respiratory conditions such as asthma) to haze output.
•
Do not point haze output directly at a person’s face or at face height.
Safety information
Product overview
Product description
The Jem Compact Hazer Pro™ is a versatile haze machine from Martin
Professional designed for the highly demanding professional market. Its ability to
produce exceptionally fine atmospheric haze in a short period of time makes it an
ideal choice for rental houses, shows, theatres, TV studios, clubs, bars, cruise
ships, theme parks and more.
Robust yet small and lightweight, the Jem Compact Hazer Pro™ is capable of
dispersing an even, continuous haze with superior optical clarity and reflectivity,
the perfect small-particle haze for highlighting today’s highly defined light beams.
A high-quality air pump system ensures smooth distribution while a unique
mixing channel allows the haze to optimize before being expelled.
Congratulations on your purchase of the Jem Compact Hazer Pro™ from Martin.
Details of the full range of Martin products are available on our website at
www.martin.com.
Features at a glance
•
Finest haze production in its class
•
Small particle, even haze
•
Continuous output
•
1 minute heat up time
•
Water-based fluid with long hang time
•
Up to 70 hours continuous operation
•
Low noise
•
Lightweight
•
Optical Density Timer Control system (ODTC)
•
Variable haze and fan controls with 5% increments
•
2.5 liter fluid capacity
•
Sealed fluid system for transportation
•
Advanced Pump Technology (APT)
•
Shutdown button prevents clogging
•
Shutdown with automatic start-up cleaning mode (if shutdown not
performed correctly)
•
RDM ready
•
On-board DMX 5pin
•
User-friendly on-board control panel
•
Optional Flying Kit, Air Director and Digital Remote Control
Use only Martin C-Plus Haze Fluid™. Use of other fluid will void
warranty.
Shutdown switch must be used when turning off to prevent clogging.
Product overview
7
Product details
Shutdown
switch
AVR program
upload socket
(behind fluid tank)
Digital
remote
socket
Main power
switch
Power inlet
connector
5 pin DMX
input and
link
Digital control
panel
Fluid tank
Haze output
port
Warning, high
temperature vapour and
surfaces!
8
Product overview
Quick Start
You are no doubt eager to switch on the machine and try it out by making a lot of
haze. This section tells you how to do that. However, please also make the time
to read the safety and servicing instructions in the remainder of this manual.
Setting up
Locate the machine in a suitably large area with nothing in front of the haze
output.
Fill the fluid tank with Martin C-Plus Haze Fluid™ only. Use of other fluid will
void the warranty.
Connect a suitably rated power supply to the machine using the supplied Neutrik
Powercon cable. The power requirements are:
4.4A @ 230V (EU model)
8.68A @ 120V (US model)
Now set the mains switch, at the rear of the machine, to the ‘ON’ position. Select
STBY from the RUN menu. The display will show HEAT, then after about 60
seconds the display will show RDY and the machine is ready to produce haze.
Making haze
Press the Menu < > buttons until the display shows RUN, then press the Value
Up/Down buttons to select CONT (continuous). Press Enter.
If no haze is output or you want to change the haze density, press the Menu < >
buttons until the display shows HAZE, then press the Enter button and check that
the HAZE setting is above 0%. If not, use the Value up/down buttons to select a
value above 0%.
You can also adjust the fan speed using the FAN menu.
If no haze is produced it may be necessary to prime the machine,
press the Menu <> buttons until the display shows PRME, then press
the Value Up button so the display shows Y, then press the Enter
button.
Switching off
The Compact Hazer is designed to run a self-cleaning cycle before power down
to help prevent blockages. Before disconnecting the power, you should start the
cleaning cycle by pressing the Shutdown Switch on the rear of the unit above the
DMX connectors. The red LED in the shutdown switch will be lit if a cleaning
cycle is needed.
If cleaning is needed, the display will show “WAIT”, then “WT44” counting down
to “WT00”. When the display shows “OFF” the power may be turned off.
Do not turn off the power without using the Shutdown switch. This will
cause the unit to enter a cleaning cycle when next switched on, and
over time will lead to blockages and malfunction of the unit.
Quick Start
9
Installation and setting up
DANGER! DO NOT operate the haze machine until you have read and observed
all the precautions listed under “Safety information” on page 4.
Location
The Jem Compact Hazer Pro™ is designed to be located on the floor or may be
suspended using the optional flying bracket. If suspending the machine, a
standard truss bracket (available from Martin) should be attached to the
machine’s flying bracket with an M12 bolt and nyloc nut.
The machine can operate in any orientation from 30 degrees upwards to 30
degrees downwards. Steeper tilting may cause fluid leakage.
If the machine is to be suspended, ensure the mounting surface can support the
weight of the machine. Do not suspend the machine over areas where people
will be underneath. Use only the correct Martin flying bracket to suspend the
machine.
Ensure that there is at least 100mm clearance all round the machine and at least
60cm in front of the haze output.
AC power
Before using the machine, ensure that a grounding-type (earthed) power plug
that fits the local power outlets is installed on the Neutrik Powercon cable
provided.
DANGER! Make sure the power plug is correctly rated:
• For EU (230V) use fit a plug rated 10 amp minimum
• For US (120V) use fit a plug rated 10 amp minimum
When installing the plug, follow the plug manufacturer’s instructions and connect
pins as follows:
Yellow and green wire to ground (earth), blue wire to neutral and brown wire to
live.
The table below shows some common pin identification schemes.
10
wire
function
marking
screw colour
brown
live
“L”
yellow or brass
blue
neutral
“N”
silver
green/yellow
earth
Installation and setting up
green
Before connecting the haze machine to power, verify that the AC supply is
adequately dimensioned for the current draw of the machine. The machine
requires:
4.4A @ 230V (EU model)
8.68A @ 120V (US model)
Check that the local AC voltage is appropriate, as indicated on the machine’s
serial number label. If your AC voltage is outside the appropriate range, do not
use the machine. Contact Martin Service for assistance.
Setting up
Fill the fluid tank only with Martin C-Plus Haze Fluid™ (see page 20).
If DMX control is being used, connect the machine to the DMX line (see page 18)
If the Jem Digital Remote is being used (optional accessory), connect the remote
to the Remote socket (see page 8).
Final checks
Before applying power to the haze machine, verify the following:
• the machine is safely located or installed and meets the location
requirements stated on page 10
•
the operator is familiar with, and able to comply with, the requirements
for safe operation listed on page 4.
•
the haze fluid is one of the genuine Martin fluids listed under “Haze fluid
options” on page 20.
•
the machine is electrically grounded (earthed)
•
the AC power distribution circuits and lines are adequately rated for the
current load
Turning on the power
Turn on the main power switch located next to the power inlet. Select STBY from
the RUN menu. The display will show HEAT, then after about 60 seconds the
display will show RDY and the machine is ready to produce haze.
Turning off the power
The Compact Hazer is designed to run a self-cleaning cycle before power down
to help prevent blockages. The cycle takes 45 seconds. Before disconnecting
the power you should start the cleaning cycle by pressing the Shutdown Switch
on the rear of the unit above the DMX connectors. The red LED in the shutdown
switch will be lit if a cleaning cycle is needed.
If a cleaning cycle is needed, the display will show “WAIT”, then “WT44” counting
down to “WT00”. During this time the unit purges the fluid from its internal
pipework to help prevent blockages.
When the display shows “OFF” the power may be turned off.
Installation and setting up
11
Do not turn off the power without using the Shutdown switch. This will
cause the unit to enter a cleaning cycle when next switched on, and
over time will lead to blockages and malfunction of the unit.
The cleaning cycle on power up is shown on the display as WT44” counting
down to “WT00”, as for the shutdown cycle. Once the display reaches “WT00”,
normal operation of the unit will start.
12
Installation and setting up
Control settings
Overview
The digital display in the centre of the top panel allows you to configure the
machine using option menus.
Digital display

Menu previous/next
buttons
Value down/up
buttons
Enter/store button
The machine is factory set so the lower of the ‘Value down/up’ buttons
increases a setting. It is possible to change this. Prior to powering the
machine up simply press and hold the button you wish to use to
increase a setting and press the main power button. Once the display
comes on you have successfully configured your preference. The
machine will store this setting until the above procedure is performed
again.
Setting Run mode
The Run mode sets the operational mode of the unit, either Off, Standby (heaters
remain on), Fan only, Timer mode or Continuous mode.
Use the Menu Previous / Next buttons to select the  option.
Use the Up/Down buttons to select .
Press the Enter button to store the setting. The display shows .
Selecting OFF will cause the machine to begin its cleaning cycle ready for power
off, if cleaning is required. This is the same as pressing the Shutdown button on
the rear.
Setting Haze density
Use the Menu Previous / Next buttons to select the  option.
Use the Up/Down buttons to select the density from  – .
Press the Enter button to store the haze setting. The display shows .
If you want to temporarily change the haze density, do not press Enter.
The haze setting will go back to its stored value next time the machine
is powered up. This applies to all options.
Control settings
13
Setting Fan speed
Use the Previous / Next buttons to select the  option.
Use the Up/Down buttons to select the fan speed from  – .
Press the Enter button to store the fan setting.
The fan will run continuously if set above 0% and the RUN menu is set to FAN,
TIME or CONT.
If haze is being produced and the fan is off or set to a low speed, the fan speed
will be automatically increased to prevent build-up of haze at the machine output.
Setting the Timer
The timer can be operated in two different modes.
Mode 1
Cycle mode
Select the Time option from the Run menu.
The TRUN and TOFF values are set in seconds and are in the range 1-90 and 2089 respectively. The haze and fan values are taken from the menu settings for
Haze and Fan. The timer will cycle continuously until the run menu is changed.
Use this mode for maintaining a low level of haze in smaller venues.
Mode 2
ODTC (Optical Density Timer Control system) mode
Select the Time option from the Run menu.
The TRUN value is set in minutes and is in the range 1-90. The TOFF value
should be scrolled to max, at which point the display will show ODTC.
During the initial TRUN period the haze and fan values are both set to maximum.
When the TRUN period expires the haze and fan values are taken from the menu
settings for Haze and Fan. The timer will cycle once only, and will end by
displaying ODTC as the TOFF value.
Use this mode for rapidly filling a large venue, then dropping back to a level
suited to maintaining the haze density in the venue.
When the timer is running and the display is not showing a menu, the
display shows TRUN or TOFF as the timer cycles between run and off
modes.
Setting the DMX base address
Use the Previous / Next buttons to select the  option.
Use the Up/Down buttons to set the DMX base address from  to . If
you hold down the button the address will count up or down.
Press the Enter button to store the address setting.
The machine will automatically respond to a DMX controller whenever it is
connected.
When using in a DMX system ensure the LINK menu is set to RECV to avoid
causing DMX errors to other devices on the system.
14
Control settings
Setting the master-slave link mode
It is possible to control several machines from one digital remote. The machine
with the remote plugged into it becomes the Master. The other machines are
Slaves. The machines are interconnected with DMX cabling.
Use the Previous / Next buttons to select the  option.
Use the Up/Down buttons to select  (slave unit) or (master unit).
Press the Enter button to store the link setting.
The machine should be set to  only if it is running as a master. If running
as a slave, stand-alone or DMX controlled it should be set to .
Alt option
This option is not currently used and has no effect on the machine.
Priming the machine after fluid out
If the machine runs out of fluid it should be shut down to prevent damage to the
pump. To suck the new fluid back into the machine, replace/refill the fluid tank
and use the prime function.
Use the Previous / Next buttons to select the  option.
Use the Up/Down buttons to change the option to .
Press the Enter button to start the priming function.
The machine will pump at full power for about 10 seconds or until the unit senses
fluid in the heat exchanger.
To exit this menu if you decide not to activate the Prime function, select  and
press Enter.
If the machine is not up to operating temperature the Prime function will do
nothing.
Resetting options to factory settings
The factory settings configure a standard mode of operation for the machine.
Use the Previous / Next buttons to select the  option.
Use the Up/Down buttons to change the option to .
Press the Enter button to reset all options.
To exit this menu if you decide not to reset the options, select  and press Enter.
The factory settings are:
option
setting
HAZE

FAN

TRUN
 seconds
TOFF
seconds
RUN

Control settings
15
16
ADDR

LINK

ALT

PRME

Control settings
Remote control
Overview
The Jem digital remote control, available separately, may be used for remote
control of the Jem Compact Hazer Pro™. Several machines may be controlled
from one remote using the LINK function (see page 15).
Display
XLR socket
XLR socket
(on rear)
Timer button
Haze button
Functions
The remote control provides the following functions:
•
Haze button: turns haze output on and off. Press once to start haze and
again to stop.
•
Timer button: turns the haze timer on and off.
•
Haze level setting (HAZE = 0 -100%)
•
Fan speed setting (FAN = 0 -100%)
•
Timer run time/off time settings (TRUN = 1 -90 seconds, TOFF = 20-89
seconds)
•
Run mode (RUN = OFF, STBY, FAN, TIME, CONT)
The functions are the same as on the built in control panel and are described on
page 13.
The RUN menu duplicates the functions of the Haze and Timer buttons. The
buttons are simply a quick way to control this menu function.
Connection
The remote control has two identical XLR sockets on the top and back for
connection to the Jem Compact Hazer Pro™. Plug the cable provided with the
remote control into one of these sockets and into the 3-pin XLR socket on the
rear panel of the Jem Compact Hazer Pro™.
The remote control is powered through its cable by the Jem Compact Hazer
Pro™; no batteries are required.
The cable may be extended to up to 25 m (82 ft.) with a 3-pin XLR DMX cable,
available from your Martin dealer.
Remote control
17
DMX control
Overview
DMX is a digital control system widely used in entertainment and architectural
lighting. Any controller meeting the DMX-512 standard may be used to control
and program the haze output of the Jem Compact Hazer Pro™.
When a DMX signal is present, the Jem Compact Hazer Pro™ standalone functions do not work. To fire the unit from the control panel or
remote control, the DMX controller must be powered off or
disconnected.
Connection
The Jem Compact Hazer Pro™ provides 5-pin XLR sockets on the rear panel of
the base for DMX connection.
For best results, use cable designed for high speed digital data transmission.
Suitable DMX cable is available from your Martin dealer.
DMX functions
The Jem Compact Hazer Pro™ address setting must match the DMX address
allocated to it on your controller. To set the address, see “Setting the DMX base
address” on page 14. The Jem Compact Hazer Pro™ requires three DMX
channels.
For example if the Jem Compact Hazer Pro™ is set to DMX address 100, channel
1 will be controlled by address 100, channel 2 will be controlled by address 101
and channel 3 by address 102.
When the machine is at running temperature and is under DMX control it displays
.
The functions of each DMX control channel are shown on the following page.
18
DMX control
Channel 1
Haze
output
Level
Channel 2
Fan
output
level (fan
will always
run if haze
is active)
Channel 3
Special
functions
DMX value
range
0-19
20-29
30-39
……..
210 -255
DMX value
range
0-19
20-29
30-39
……..
210 -255
DMX value
range
0-50
51-100
101-150
151-200
201-255
Function
Macro description
Idle range
Haze 5%
Haze 10%
…….
Haze 100%
Function
None
Macro description
Idle range
Fan 5%
Fan 10%
…….
Fan 100%
None
Function
Macro description
Idle range
Prime
None
5 seconds within
range to activate
once
None (level
triggered)
5 seconds within
range to activate
once
None, but heaters
will stay on if
channel 3 returns to
zero
Auto Fan
mode
Heater off &
shutdown
Heater on
(normal
operation)
Default
value
0
Default
value
0
Default
value
0
Note that when the heaters are on, Channel 3 can stay at level 0 without affecting
the operation of the machine.
This means that Channel 3 need only go to 100% once at the start of a show,
then it can assume a default of zero without the heaters turning off, thus ensuring
that the machine is ready when the show runs again. To turn the heaters off, use
the Heater Off macro.
DMX control
19
Haze fluid types
The Jem Compact Hazer Pro™ must only be used with C-Plus Haze Fluid™.
Martin supplies high quality haze fluids that are based on ultra-pure deionized
water. No other fluid is suitable for use.
DANGER! The Jem Compact Hazer Pro™ can run safely only on the specific
haze fluid it is designed for. Use ONLY the Martin haze fluid designated in this
manual. NEVER use any other type of fluid, or toxic gas may be produced.
You will probably also cause damage to the system that will invalidate the
product warranty. Do not dilute haze fluid with water or any other liquid.
Discard haze fluid if it becomes contaminated.
20
Haze fluid types
Basic service
Before servicing the Jem Compact Hazer Pro™, read and observe all the
precautions listed in “Safety information” on page 4. Any service not
described in this section must be carried out by a Martin service technician.
Cleaning
Excessive dust, haze fluid, and dirt build-up will degrade performance and cause
overheating and damage to the machine that is not covered by the product
warranty. To maintain adequate cooling, dust must be cleaned from the outer
casing and air vents of the machine periodically.
Isolate the machine from power and allow to cool completely before cleaning.
The haze output nozzle remains hot for a period after use.
•
Remove dust from the air vents with a soft brush, cotton swab, vacuum,
or compressed air.
•
Clean haze fluid residues from the haze output of the machine using a
damp cloth.
•
Clean the outer casing with a damp cloth only.
Fuse replacement
The two fuses for the haze machine are located on the electronics board inside
the unit.
DANGER! Disconnect the power supply before removing any covers. Live
parts inside!
To replace a fuse, disconnect the power cord from the supply, unscrew the
screws holding the top cover of the unit and remove the cover. The electronics
board is located in the compartment under the display.
Remove the spent fuse and replace with one of exactly the same size and rating.
The fuse type is indicated below. Contact Martin Service if the fuse blows
repeatedly.
F1
120V = 10AT
230V = 6.3AT
F2
120V = 3.15AT
230V = 3.15AT
Basic service
21
Troubleshooting
Problem
Probable cause(s)
Suggested remedy
Machine not at operating
temperature
Wait until  message
no longer shown
 set to 0
Increase setting
 set to 0
Increase setting
DMX signal present
Disconnect or turn off DMX
controller
DMX address setting
incorrect
Change DMX address (page
14)
Poor connection in DMX line
Check DMX cables and
connections
LINK menu is set to SEND
Set LINK menu to RECV
Haze output is weak
Machine requires priming
Prime machine (page 15)
Wet, greasy, non-uniform
haze output, fluid drips or
spits from nozzle, or very
loud noise when firing
machine
Incompatible haze fluid
Use approved fluid!
Mains fuse blown
Replace fuse (page 21)
No power at AC cable inlet
Check power cable and
circuit breaker
LINK menu is set to SEND
Set LINK menu to RECV
Machine will not produce
haze when control panel set
to RUN or remote control
Haze switch turned on
Machine can be fired from
control panel or remote
control, but not by DMX
controller
Machine appears dead
Machine causes DMX errors
to occur on other units when
connected to a DMX system
22
Troubleshooting
Status messages
message


reason
The heaters are Off, the unit is shut down.
The unit is heating up to operating temperature.
The heater is at operating temperature, but Haze is not turned

on (RUN set to STBY or HAZE set to 0%).
The heater is at operating temperature and the unit is under

DMX control.
The heater is in run mode and is producing haze.

The machine has detected an error with its calibration settings

and will not operate. Call Martin Service.
The machine has detected an error in the temperature sensor

and will not operate. Call Martin Service.
The machine is running a cleaning cycle which lasts 45

seconds (number may be 45 to 0)
Resetting the machine after fluid out
If the machine runs out of fluid simply refill the fluid container and follow the
priming instructions on page 15.
Status messages
23
Specifications
Physical
Length ......................................................................................................... 532mm
Width ........................................................................................................... 224mm
Height .......................................................................................................... 278mm
Dry weight ...................................................................................................... 8.5Kg
Performance
Operating time ....................................................................................... continuous
Warm up time (approx) .............................................................................. 1 minute
Max’ operating time at min output (2.5L)................................................... 70 hours
Control and programming
Control options ................................... onboard digital control panel, DMX (5 pin),
...................................................... Multi function digital remote control (optional).
DMX channels ...................................................................................................... 3
RDM ..................................................................................................... RDM Ready
Fluid system
Fluid pump .......................................................... Oscillating piston, high pressure
Capacity .......................................................................................................... 2.5 L
Compatible fluids ..................................................... Jem C-Plus Haze Fluid™ only
Connections
DMX data .................................................................................................. 5 pin XLR
Remote / machine link .............................................................................. 3 pin XLR
AC power ................................................................................... Neutrik PowerCon
Electrical
AC power (EU models) .............................................................. 220-240V, 50/60Hz
AC power (US models) .............................................................. 110-120V, 50/60Hz
Main fuse (EU models) .................................................................................. 6.3AT
Main fuse (US models) ................................................................................... 10AT
Heat exchanger (EU models) ......................................................................... 900W
Heat exchanger (US models) ......................................................................... 900W
Thermal
Maximum ambient temperature (Ta max) ............................................. 40°C (104°F)
Exterior surface temperature, steady state, at 20°C ambient .................. 30°C (86°F)
Max nozzle temperature ..................................................................... 290°C (554°F)
Approvals
European EMC: .......................................................................... EN 61000-6-3:2001
European safety:.......................................................................... EN 60 335-1:2002
Immunity: .................................................................................... EN 61000-6-1:2001
................................................................. EN 50 366 : 2003 Electromagnetic fields
ETL approval (pending) ...................... UL Std.998, CAN/CSA Std. C22.2 No 104-01
24
Specifications
Included items:
User manual
Power cable
Fluid Container 2.5L
Ordering information
JEM Compact Hazer Pro™ haze machine 115V ................................. P/N 92225960
JEM Compact Hazer Pro™ haze machine 230V ................................. P/N 92225950
Accessories
Remote Control, JEM Compact Hazer Pro™ ...................................... P/N 92765040
Air diverter, JEM Compact Hazer Pro™ .............................................. P/N 92625011
Flying kit, JEM Compact Hazer Pro™ ................................................. P/N 92610003
Specifications subject to change without notice. For the latest product specifications, see
www.martin.com
Specifications
25
26
Specifications
Dis p o s ing o f th is p ro d uct
Martin™ products are supplied in compliance with Directive 2002/96/E C of the E uropean
Parliament and of the Council of the E uropean Union on WE E E (Waste E lectrical and
E lectronic E quipment), as amended by Directive 2003/108/E C, where applicable.
Help preserve the environment! E nsure that this product is recycled at the end of its life.
Your supplier can give details of local arrangements for the disposal of Martin products.
Specifications
27
Martin Professional A/S,Olof Palmes Allé 18, DK-8200,Aarhus N
Phone: +45 87 40 00 00 Internet: www.martin.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement