Pyronix Enforcer 32-W User manual

EN50131-1:2006+A1:2009
EN50131-3:2009
EN50131-6:2008
EN50131-5-3:2005+A1:2008
PD6662:2010
Security Grade 2
Environmental Class II
Software Version >9.13
User Manual
Wireless Alarm System
RINS1548-4
PIEZO WARNING
The wireless system contains a
loud siren, please be aware of
this after an activation
SMS CHARGES:
If you’re using the SMS text messaging facility of the panel, you
will be charged at 50p every two weeks for an SMS Server
Update call. This charge is raised via use of a premium rate
telephone number. Please see page 23 for details.
Contents Page
Contents Page ..................................................................................................................... 2
1. Introduction .................................................................................................................... 4
2. The Setting Devices .......................................................................................................... 5
2.1 The Wireless Panel Keypad and Additional Keypads (EUR-068) ........................................... 5
2.2 The Internal Tag Reader (EUR-107) ................................................................................ 5
2.3 The External Tag Reader (EUR-108) ............................................................................... 5
3. The KF4-WE (Wireless Keyfob) ........................................................................................... 6
3.1 Locking the Keyfob ...................................................................................................... 6
3.2 Buttons ...................................................................................................................... 6
3.3 Quick Setting .............................................................................................................. 6
4. Using Predictive Text ........................................................................................................ 7
5. Setting The System .......................................................................................................... 8
5.1 Using a PIN Code or Tag ............................................................................................... 8
5.2 Using the Wireless KEyfob (KF4-WE) .............................................................................. 8
6. Unsetting The System .......................................................................................................9
6.1 Using a PIN Code or Tag ............................................................................................... 9
6.2 Using a Wireless Keyfob (KF4-WE) ................................................................................. 9
7. Unsetting after an alarm.................................................................................................. 10
7.1 Using a PIN Code or Tag ............................................................................................. 10
7.2 Using a Wireless Keyfob (KF4-WE) ............................................................................... 10
8. Using an Tag Reader ....................................................................................................... 11
8.1 Setting and Unsetting ................................................................................................. 11
8.2 Entry Control............................................................................................................. 11
9. Anti Code / Engineer Restore Facility ................................................................................. 12
9.1 Anti-Code ................................................................................................................. 12
9.2 Engineer Reset .......................................................................................................... 12
10. Intelligent Setting ......................................................................................................... 13
11. Fault Indications / Unable To Set .................................................................................... 14
11.1 Fault Indications ...................................................................................................... 14
11.2 Unable to Set .......................................................................................................... 14
11.3 Keyfob Fault Indications ............................................................................................ 14
12. Advanced Functions ...................................................................................................... 15
12.1 Chime Feature ......................................................................................................... 15
12.2 Omitting Inputs ....................................................................................................... 15
12.3 Keypad Hold Up ....................................................................................................... 15
13. Master Manager Menu ................................................................................................... 16
13.1 Entering the Master Manager Menu ............................................................................. 16
13.2 Exiting the Master Manager Menu ............................................................................... 16
13.3 Set Date and Time ................................................................................................... 17
13.4 Omit Inputs............................................................................................................. 17
13.5 Change Codes (Adding codes, tags and keyfobs) .......................................................... 18
13.5.1 Button Actions: .................................................................................................. 18
13.5.2 Flexi Set ............................................................................................................ 18
13.6 Review Logs ............................................................................................................ 20
13.7 Phonebook .............................................................................................................. 20
13.8 Walk Test ............................................................................................................... 21
13.9 Siren Test ............................................................................................................... 21
13.10 Start CHC SMS Update ............................................................................................ 21
13.11 Dial Out Menu ........................................................................................................ 22
13.12 Allow Engineer Menu ............................................................................................... 22
13.13 Block Remote Set ................................................................................................... 22
13.14 Block UDL ............................................................................................................. 23
14. Disclaimer ................................................................................................................... 23
15. Engineer Contacts and Tables ......................................................................................... 24
15.1 Engineer Information ................................................................................................ 24
15.1.1 Intruder Alarm Signal .......................................................................................... 24
15.1.2 Tamper Alarm Signal........................................................................................... 24
15.1.3 Keypad ............................................................................................................. 24
15.1.4 Tag Reader (Or Tag at a keypad) .......................................................................... 24
15.2 Certification ............................................................................................................ 24
15.3 Input Contact Table .................................................................................................. 25
15.4 Code Table .............................................................................................................. 26
Default User Code: 1234
Default Master Manager: 2222
User Manual
1. Introduction
Two Way Wireless Security Protects Your Family and Property Without Compromise.
This wireless alarm system has been designed with your security in mind; with quick and easy
installation and minimal maintenance, this system protects your home or property with a multitude
of unique features.
Taking full advantage of the innovative two way wireless technology, the wireless devices on this
system are constantly communicating with each other, using High Security Wireless Encryption
Protocol.
Compared to a conventional one way wireless system, where devices can be ‘asleep’ for up to five
minutes at a time, therefore compromising your security, this wireless alarm system ensures your
safety at your home or office at any time.
This wireless alarm system has been engineered to be secure, reliable and easy to use. It includes
the following features:
Battery Monitoring/Saving
Advanced technology preserves the battery life of each wireless device. However, the system
informs you when a battery needs replacing a month in advance before the device stops working.
This key feature gives you enough time to change the battery in the specific device. Conventional
wireless alarm systems may not give you a low battery warning signal, meaning that devices could
stop working, leaving your environment unprotected.
Intelligent Setting
This feature enables the control unit to automatically recognise when you’re at home or away. Using
this knowledge this system is able to set itself in the correct mode without you having to choose.
User Friendly Keyfobs
The fully two way wireless keyfob allows you to see the status of the control unit via 3 colour LEDs:
System set: When the system is set a RED LED will illuminate
System unset: When the system is unset a GREEN LED will illuminate
System fault: When the system is in fault condition an AMBER LED will illuminate.
It is possible to allocate different functions to each keyfob such as setting / unsetting different
areas, activating outputs, requesting system status, and activating panic alarms. Up to 32 wireless
keyfobs can be added to the wireless alarm system. Each wireless keyfob has its own user ID which
can be reported to the ARC and stored into the event log of the control panel individually. The
keyfob also allows you to set/unset every area individually, giving you total control of your system.
User Automation Outputs
User automation outputs gives you the option to operate up to 20 devices such as gates, lights,
sprinklers, etc. via your keypad or remotely via your keyfob, extending the use of your security
system
SMS Text Notifications
Receive notifications via SMS text messages of any incidents within your home in real time. This can
be programmed to send a notification in different situations: System is set or unset: Notification that
your child has returned home from school safely. Alarm activation: Notification that the alarm has
been triggered, allowing you to monitor your home from anywhere in the world.
This wireless alarm system has 4 area's in which may be set up in the following way:
Area A: Full set of the house
Area B: Downstairs unset. Upstairs set.
Area C: Garage set. Rest of house unset.
Your engineer will be able to design the system according to your needs.
Page: 4
User Manual
2. The Setting Devices
2.1 The Wireless Panel Keypad and Additional Keypads (EUR-068)
Additional wired keypads may also be connected to the wireless control panel, please ask your
Engineer for more information.
a = Exits the Master Manager menu (page: 16), and
selects Area A when setting.
b = Moves backwards in the Master Manager menu
(page: 16), and selects Area B when setting.
c = Enables chime, displays additional information in the
event log, and selects Area C when setting.
D = Moves forward in the log, scrolls between options
and enters the Master Manager menu (page: 16), and
selects Area D when setting.
f p = Not used.
[ ] = Directional buttons and enables/disables
functions.
I = Selects commands
A = Cancels items, resets the panel and moves to next
item in a menu item.
2.2 The Internal Tag Reader (EUR-107)
The Internal tag reader can be used for setting/unsetting, entry control or access control.
Ask your engineer for more details.
Tag Area (Where you present your
tag to set/unset)
Alert LED
Alarm LED
Tamper LED
Fault LED
Unset LED
2.3 The External Tag Reader (EUR-108)
The External tag reader can be used for setting/unsetting, entry control or access control.
Ask your engineer for more details.
To set/unset the system using the External Tag Reader,
present a pre-programmed tag to the centre of the prox.
The prox will display the system status: Green = Unset.
Red = Set. Present the tag again within 10 seconds and
the system will set or unset.
The system will then set depending on the type of exit
mode programmed (Final door, Timed or Push to set)
Page: 5
User Manual
3. The KF4-WE (Wireless Keyfob)
The wireless keyfob has 4 buttons that may be programmed for specific purposes (please see
‘CHANGE CODES’ on page 18 for more information).
3.1 Locking the Keyfob
All 4 buttons on the keyfob may be ‘locked’ so that any accidental presses will not affect your
wireless alarm system (for example, this protects the buttons from being pressed accidently if a
keyfob is in someone’s pocket).
3.2 Buttons
The buttons can be customised (see Change Codes, page 18) to operate as desired. The table
below gives the defaults of how each button is programmed. These can be changed in the
‘Change Codes’ function – see page: 18.
LOCK BUTTON = Set Area A
When pressed, the Area A will be start to set.
UNLOCK BUTTON = Unset Area.
When pressed, the wireless alarm system will unset any area that is already
set.
I BUTTON = Set Area B
When pressed, the Area B will be start to set.
II BUTTON = Show Status
When pressed, if the GREEN LED is shown then the wireless alarm system
will be unset. If the RED LED is shown then the wireless alarm system will be
set.
3.3 Quick Setting
If one of the buttons is programmed as ‘Set Area’, the wireless alarm system can be set by
pressing the programmed button on the keyfob. The keypad will then start to count down the
exit time, or wait for a ‘final door’ to be opened and closed or wait for a Push to Set (PTS)
button to be pressed (depending what the exit mode is programmed as by the engineer).
Once the alarm panel is in this ‘setting’ stage, it is possible to ‘quick set’ the system by pressing
the same button again; this will reduce the time to set to ‘immediate setting’. The alarm panel
will revert to the normal display with the time showing, but a beep will be heard once the
system has been set.
Please note this feature cannot be used if ‘Intelligent Setting’ is enabled.
Page: 6
User Manual
4. Using Predictive Text
The wireless alarm system incorporates predictive text, so the system will predict the word that is
being spelt.
For example, if you type ‘John’, press 5 once and the name ‘Julia’ will appear. Press D to move
the cursor over the ‘u’, and press 6 3 times to change it to an ‘o’. The name ‘John’ will now
appear. Press I to accept.
If the word that you require does not appear in the list, just continue typing the word letter by
letter.
In addition, the a b c D keys are used as follows:
a = make the character into a capital
b= move cursor left
c= clears cursor / adds a space
D = moves cursor right
Page: 7
User Manual
5. Setting The System
5.1 Using a PIN Code or Tag
Enter a valid PIN code or present a valid
tag to the symbol as shown.
Enter the area you wish to set, and press
I. ‘Please wait setting wireless’ will be
displayed.
There are three different setting
methods your installer will instruct you
through:
Final Door: Leave the building and
make sure the exit door is closed
properly.
Timed: Make sure you leave the building
before the timer shown on the keypad
expires.
Push to set: Press the push to set
button installed by your engineer to set
the system.
5.2 Using the Wireless KEyfob (KF4-WE)
To set via a keyfob. Pressand hold for more
than 2 seconds.
The keyfob LED will start to flash GREEN
indicating that the system is starting to set.
‘Please wait setting wireless’ will be displayed
on the keypad and the programmed area will
begin to set.
To ‘quick set’, press and hold thekey a second
time for 4 seconds.
Once set, the keyfob LED will illuminate RED
indicating that the system is now set.
Page: 8
User Manual
6. Unsetting The System
6.1 Using a PIN Code or Tag
Enter the building, the 'entry time' will
start.
Enter a valid PIN code or present a valid
tag to the symbol as shown.
The area that the code is assigned to will
be unset.
NOTE: If ‘flexi-set’ is disabled (see page
18) then the system will automatically
Unset that level set once a valid user
code or tag is presented.
6.2 Using a Wireless Keyfob (KF4-WE)
To unset via a keyfob. Press .
The keyfob LED will start to flash GREEN
indicating that the system has unset.
NOTE: Unsetting with a keyfob will only be
allowed if your engineer has enabled this.
Page: 9
User Manual
7. Unsetting after an alarm
7.1 Using a PIN Code or Tag
Enter a valid PIN code or present a valid
tag to the symbol as shown.
The alarm symbol will flash indicating
there has been an alarm activation and
the keypad will display which input has
activated.
Press A to reset the system.
7.2 Using a Wireless Keyfob (KF4-WE)
NOTE: Unsetting with a keyfob will only
be allowed if your engineer has enabled
this.
To unset via a keyfob. Press .
The keyfob LED will start to flash GREEN
indicating that the system has unset.
Resetting the system after an alarm can
only be done at the keypad.
Page: 10
User Manual
8. Using an Tag Reader
8.1 Setting and Unsetting
If you have a tag reader installed, then it will be possible to set and unset the wireless alarm
system using a tag (the same tags can also be used to set/unset via the keypad prox).
There are two types of readers that can be used with the wireless alarm system - the internal
tag reader (used for indoors only) and the external tag reader (used for both indoors and
outdoors).
Tags for the readers need to be programmed through the ‘Change Codes’ function in the Master
Manager Menu (see page 18). The internal and external readers can be both assigned to
individual areas, this will need to be set up by your engineer.
8.2 Entry Control
The readers may be used for entry control, which means they can operate automatic locks for
example as well as setting and unsetting the system. This can be set up by your Engineer.
External Reader Instructions:
Arming: Present a valid tag to the reader, the GREEN LED will illuminate on the external
reader, remove the tag, the door will unlock, then present the same tag within 10 seconds and
the system will arm and the door will lock.
Disarming: Present a valid tag to the reader and then remove it, the status will be shown (the
alarm symbol will illuminate indicating the system is armed on the internal reader and the RED
LED on the external reader), present the same tag within 10 seconds again and the system will
be disarmed, and the door will unlock.
Access Control/Entry Control: The readers can be used also for opening doors only without
the ability to arm and disarm. Please contact your installer for more information on this feature.
Page: 11
User Manual
9. Anti Code / Engineer Restore Facility
9.1 Anti-Code
Your Engineer may have set up the system so that either an ‘Anti-Code’ or 'Engineer Restore' is
required in order to fully reset the wireless alarm system (your code will still silence the alarm,
but it will not reset the system).
After alarm activation has occurred,
enter a valid PIN code, or preset a valid
tag, or press on the keyfob to silence
the alarm.
The keypad will display as shown to the
right.
Take note of the number, on the screen
and call your Alarm Receiving Centre
(ARC).
Press I.
When the time is displayed, enter the
number given to you by the ARC.
‘Engineer Restore Performed’ will be
displayed.
Press A .
9.2 Engineer Reset
When the time is displayed, enter the
Engineer code.
‘Engineer Reset Performed’ will be
displayed.
Press A.
Page: 12
User Manual
10. Intelligent Setting
If intelligent set is enabled by your engineer, the system automatically recognises whether to full set
(Area A), or part set. (Area B). ‘Flexi Set’ (Page 18) should be disabled for this feature to work
properly.
Enter a valid PIN code, or present a valid
tag to the circled area, or press  on
the keyfob.
The system will set in area B (the user
code/tag/keyfob must be programmed
for areas A and B).
If a final exit input is activated during
the setting procedure the system will
quick set area A.
Page: 13
User Manual
11. Fault Indications / Unable To Set
11.1 Fault Indications
Any faults that occur on the system will
be easily recognised by the flashing
ALERT LED.
To see what the fault is, enter a valid
PIN code, or present a valid tag, or press
on the keyfob.
Depending on how the system has been
set up by your engineer, it may be
possible to set the system with a fault,
to do this press I.
Any fault may affect the overall performance of your alarm control panel and therefore your
engineer should be contacted for further assistance if any fault is active.
11.2 Unable to Set
If ‘unable to set’ is displayed, it indicates
that an input is open and the area where
the input is should be checked for open
windows, pets, movement etc.
If the problem cannot be solved contact
your Engineer, or omit the input (page
15)
11.3 Keyfob Fault Indications
If the panel is unable to set for any reason, the keyfob status LED flashes AMBER indicating a
fault is on the system. The fault will be shown on the keypad.
Page: 14
User Manual
12. Advanced Functions
12.1 Chime Feature
The chime can be used for any input on
the system. This can be set up by your
engineer.
To enable the chime on the keypad,
when the time is displayed, press c .
‘c’ will be displayed on the right side of
the keypad display. Press c again to
clear the chime feature.
12.2 Omitting Inputs
On occasion, a detector may need to be
isolated if a room is occupied.
Enter your user code
Press I .
Select the inputs that need to be omitted
Press A.
After 10 seconds the exit time continues.
NOTE: Inputs have to be programmed
as ‘omittable’ by your Engineer for this
feature to operate.
12.3 Keypad Hold Up
If an emergency alarm is needed, press
and hold both 1 and 7 .
A ‘hold up’ alarm will be generated.
NOTE 1: The Hold Up facility needs to
be enabled by your engineer (either
silent or full alarm)
2-Key HU and any duress codes
programmed on the system by your
engineer are not permitted to send a
signal to the Alarm Receiving Centre
under police regulations in England,
Wales or Northern Ireland
NOTE 2: The keyfob can also be
programmed to support a hold up alarm.
Please discuss this with your Engineer.
Page: 15
User Manual
13. Master Manager Menu
The Master Manager Menu has the following functions:
Function
Set Date and Time
Omit Inputs
Change Codes
Review Logs
Phone Book
Walk Test
Siren Test
Start CHC SMS Update
Dial Out Menu
Allow Engineer Menu
Block Remote Set
Block UDL
Exit Manager Mode
Description
Programs the date and time.
Omits any 24 inputs only (except Personal Attack inputs).
Adds/Edits/Deletes User PIN codes, tags and keyfobs.
Displays all event log information.
Adds/Edits/Deletes SMS phone numbers if enabled.
Tests each input.
Tests each external sounder.
Sends a test call to the SMS station if SMS is being used.
Used for uploading/downloading.
Enables or Disables Engineer access.
Blocks remote setting from the PC software.
Blocks uploading/downloading from the PC software..
Exits the Master Manager menu.
NOTE: The Master Manager code allows access to all the options above. A ‘user code’ has access to
the ‘User Menu’ which includes the functions: ‘CHANGE CODE', ‘REVIEW LOGS’, ‘ALLOW ENGINEER
MENU', and ‘EXIT USER MENU’.
13.1 Entering the Master Manager Menu
Press D.
Enter the Master Manager code or
present the Master Manager tag.
Press b or A to scroll through the
different functions mentioned above.
13.2 Exiting the Master Manager Menu
Press b or A keys to scroll through
until ‘EXIT MANAGER MODE' is displayed.
Press I.
Or, when a main menu item is displayed
(capital letters) press the a key.
Page: 16
User Manual
13.3 Set Date and Time
Press b or A to scroll to ‘SET DATE &
TIME’. Press I.
Enter the Year.
Press I.
Enter the Month.
Press I.
Enter the Day.
Press I.
Enter the Hours.
Press I.
Enter the Minutes.
Press I.
13.4 Omit Inputs
Press b or A to scroll to ‘OMIT
INPUTS’. Press I.
Enter the inputs you require to be
omitted for the next setting procedure.
Press I.
NOTE: All inputs will be only omitted for
the next setting procedure.
Page: 17
User Manual
13.5 Change Codes (Adding codes, tags and keyfobs)
The ‘CHANGE CODES’ function allows adding, editing and deleting of user codes, tags and
keyfobs. The master manager code can also be changed.
The control panel can have up to 80 user codes or tags. Up to 32 keyfobs can be learnt.
13.5.1 Button Actions:
Each wireless keyfob has 4 buttons that can be programmed for any of the functions below:
No Action = Disables the button
Show Status = If the keyfob is learnt the LED will flicker when asked for the status.
Set Area = Sets the chosen area
Unset Any Area = Unsets any area on the system
Latch Output = Enables an output that your engineer may have programmed
Timed Output = Enables an output for a period of time that your engineer may have
programmed
13.5.2 Flexi Set
Flexi-set allows you to choose which level/area to set if a user code is assigned to one or
more levels/areas. If this function is disabled, when a user code is entered, the system will
automatically set the levels/areas that the code is assigned to.
Press b or A to scroll to ‘CHANGE
CODES’. Press I.
To add a new code, tag, or keyfob press
I. Press A to delete or change a user
code (see further down for details).
Press [ or ] to choose a user
number. Press I.
Enter the new code, present a tag or
press and hold a keyfob button until the
display changes. Once ‘asterisks’ appear,
the tag or user code will be now
assigned to this user. Press I.
Programming Wireless Keyfobs
If a keyfob is programmed, the 'User
Name' will be displayed on the keypad.
Enter the user name. Press I.
Press [ or ] to choose the button to
program. Press I.
Press [ or ] to choose the action
assigned to the button. Press I.
Page: 18
User Manual
Press [ or ] to choose between
'User' or 'Manager'. Press I
NOTE: This screen will not be displayed
if you have programmed a wireless
keyfob.
Select the areas that the user will be
assigned to: A, B, C or D.
Press I.
Press [ or ] to choose between
'Unset/Set', 'Unset Only', 'Set Only' or
'None'. Press I.
(This screen will not be displayed if you
have programmed a wireless keyfob)
Press [ or ] to enable or disable
'Flexi-Set'. Press I.
(This screen will not be displayed if you
have programmed a wireless keyfob)
Enter the user name (for help on
predictive text please see page 7)
Press I.
Press I to delete or change a user.
Delete User
Press [ or ] to scroll through the
users, or enter the user number and
press I.
Press I to delete a user, or press A
to change a user.
Change User
Press I to change a user code, and
follow the screen shots previously.
Change Master Manager Code
To edit the Master Manager Code, press
I.
Enter the new code, present a tag or
press and hold a keyfob button until the
display changes. Press I.
Repeat the same procedure mentioned
previously.
Page: 19
User Manual
13.6 Review Logs
The ‘Review Logs’ function monitors all operational information of the wireless alarm system,
such as setting/unsetting information and alarm activations etc.
Press b or A to scroll to ‘REVIEW
LOGS’. Press I.
Press I.
The most recent event will be displayed,
press b or D to scroll backwards and
forwards through the log.
Press the c key to show more
information (such as which input
activated, or which user set the system
etc)
13.7 Phonebook
If SMS texting is programmed, there will be up to 4 mobile numbers also programmed which
can be changed in this function. If any numbers are added, you will need to enable each one
and also perform a CHC SMS test to activate each call (see page 21). If “do not use” is shown
on the display of a number, then a telephone number already exists that is communicating to
an Alarm Receiving Centre (this can only be changed by your engineer).
Press b or A to scroll to
‘PHONEBOOK’. Press I.
Press b or D to scroll through the
different telephone numbers.
Enter the mobile number. Press I.
Press [ or ] to enable or disable the
number. Press I.
Page: 20
User Manual
13.8 Walk Test
The ‘Walk Test’ function allows the testing of all programmed inputs on the wireless alarm
system.
Press b or A to scroll to ‘WALK TEST’.
Press I.
Select which level set to walk test. Press
I to walk test all inputs or press the
A to walk test an input individually.
Walk Test Inputs
Walk test the mentioned inputs on the
display. After all inputs have been walk
test successfully ‘walk test completed’
will be displayed.
Walk Test Individual Inputs
Press [ or ] to scroll through the
different inputs and press I to walk
test that input.
13.9 Siren Test
This function is used to test the siren and strobe outputs.
Press b or A to scroll to ‘SIREN
TEST’. Press I.
This tests both the siren and strobe
outputs. Press I.
13.10 Start CHC SMS Update
This function is used in conjunction with SMS texts. It is used to communicate with the SMS
Host computer (the mobile phone server).
Press b or A keys to scroll to ‘START
CHC SMS UPDATE'. Press I.
The control panel will then call the CHC.
If ‘Failed CHC test’ is displayed, please
call your engineer.
Page: 21
User Manual
13.11 Dial Out Menu
The control panel may be dialled into, and programming information kept on a PC using the
InSite UDL software. This function allows the control panel to dial a Pre-programmed PC
telephone number (programmed by your engineer) to directly dial to a PC. This is usually used
when your engineer requests it.
Press b or A keys to scroll to ‘DIAL
OUT MENU’. Press I.
Press [ or ] to scroll through the
different PC numbers, press I to dial
that number
Press [ or ] to select the operation
that needs to be performed. Press I.
The control panel will dial the
programmed PC. If this fails please
contact your engineer.
Press A.
13.12 Allow Engineer Menu
If this function is enabled, the engineer will require authorisation from you before they can
access the engineering menu.
Press the b or A keys to scroll to ‘ALLOW
ENGINEER MENU’. Press I.
Press [ or ] to select either ‘Yes’ or
‘No’. Press I.
13.13 Block Remote Set
Your wireless alarm system may be configured so that your alarm installation company can
remotely set/unset. Should you wish to block this access, you can enable this function
Press the b or A keys to scroll to
‘BLOCK REMOTE SET’. Press I.
Press [ or ] to select either ‘Yes’ or
‘No’. Press I.
Page: 22
User Manual
13.14 Block UDL
Your wireless alarm system may be configured so that your alarm installation company can
upload and download into the control panel, Should you wish to block this access, you can
enable this function.
Use the b and A keys to scroll to
‘BLOCK UDL’. Press the I key
Press [ or ] to select either ‘Yes’ or
‘No’. Press I.
14. Disclaimer
GSM Communications
The wireless alarm system GSM has the ability to send:
1. Electronic messages to an Alarm Receiving Centre (ARC)
2. Short Message Services (SMS).
In order for the wireless alarm system GSM to function correctly, the installer must provide and fit a
SIM card that has an appropriate airtime contract with a suitable Wireless Network Operator (WNO).
Electronic messages and SMS messages are carried by the WNO by means of networks and
transmission facilities over which Pyronix Limited (Pyronix) has no control. Pyronix shall therefore
not be responsible for the WNO’s service level or the WNO’s network failures.
PSTN Communications
The wireless alarm system PSTN Modem has the ability to send:
1. Electronic messages to an Alarm Receiving Centre (ARC),
2. Text Messages via Short Message Services (SMS).
In order for the wireless alarm system PSTN Modem to function correctly, the installer must connect
the wireless alarm system PSTN Modem to an appropriate Plain Old Telephone System (POTS) which
has an appropriate service level agreement with a suitable POTS operator. Moreover, the service
level agreement must allow the wireless alarm system PSTN the ability to dial Premium Rate
numbers.
In order for the wireless alarm system PSTN Modem to send SMS messages, the wireless alarm
system PSTN Modem must dial an embedded number that connects to an SMS server. The wireless
alarm system PSTN Modem passes the SMS message to the SMS server, which in turn forwards the
SMS to the user’s mobile phone. Please check with your installer for exact charges.
The PSTN Modem will contact our own Host Computer periodically in order to check and verify the
SMS server routing information. Charges for this service are raised by use of a premium rate
telephone number and are currently 50p per call*.
Electronic messages and SMS messages are carried by the POTS/SMS Server operator by means of
networks and transmission facilities over which Pyronix Limited (Pyronix) has no control. Pyronix
shall therefore not be responsible for the POTS/SMS Server operator’s service level or the POTS/SMS
Server operator’s network failures.
*Charges correct as of 31/3/2014
Page: 23
User Manual
15. Engineer Contacts and Tables
15.1 Engineer Information
Alarm Company
Date of Installation
Site Reference
Engineer Name
Engineer Contact Number
Installed to Grade
Environmental Class
II
Your panel is suitable for use in installations designed to meet the European requirements of
Security Grade 2, Environmental Class 2. When all parts are working normally, this equipment
in combination with the PSTN or GSM and suitable ARC equipment will meet the requirements of
ATS2.
External set/unset readers and wireless sirens meet the requirements of environmental class 4.
Number of Code Differs: tag hex code.
Your panel is designed to automatically inhibit certain functionality. The factory default settings
are shown below:
15.1.1 Intruder Alarm Signal
After 3* unconfirmed alarms in the same area or 1 confirmed alarm. * This figure is
programmable by the Engineer.
15.1.2 Tamper Alarm Signal
After 3* unconfirmed alarms in the same area or 1 confirmed alarm. * This figure is
programmable by the Engineer.
15.1.3 Keypad
After 30 key presses without entering a valid code, keys are disabled for 90 seconds. After
reinstatement, this will be repeated after each 7 key presses until a valid code is entered.
15.1.4 Tag Reader (Or Tag at a keypad)
After 6 presentations of an invalid tag, the reader will be disabled for 90 seconds. After
reinstatement, this will be repeated for each invalid tag until a valid tag is used.
15.2 Certification
All Wireless devices comply with the following EU requirements:
EMC Directive
Low Voltage Directive
R&TTE Directive
And meet the following
EN 61000-6-3:2007
+A1:2011
EN 50130-4:2011
2004/108/EC
2006/95/EC
1999/5/EC
standards where relevant:
EMC. Generic emission standard. Residential, commercial and light
industry
Immunity requirements for components of fire, intruder and social
EN 60950-1:2006
+A12:2012
Information technology equipment. Safety. General requirements
EN 50131-5-3:2005+
A1:2008
Grade 2. Interconnections for equipment using radio frequency
techniques
ETSI EN 3014893:2000
ETSI EN 300 220
CEPT/ERC
EMC. Radio equipment. Part 3: Short range devices (SRD) 9kHz to
40GHz
EMC. Receiver Class 1, Environmental Category 1
Recommendation 70-03 Annex 1
Compliant operation is only guaranteed when installed and operated according to the relevant
installation and user manuals.
Page: 24
User Manual
15.3 Input Contact Table
Input No
Input Name
Input Areas
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
Page: 25
Description
User Manual
Input No
Input Name
Input Areas
Description
57
58
59
60
61
62
63
64
65
66
15.4 Code Table
Code No
Code Type (Code/Tag/Fob)
Code Areas
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Page: 26
Code Name
User Manual
Code No
Code Type (Code/Tag/Fob)
Code Areas
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
Page: 27
Code Name
For electrical products sold within the European
Community: At the end of the electrical product’s
useful life, it should not be disposed of with
household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for
recycling advice in your country. When disposing of
the product the batteries must be removed and
disposed of separately in accordance with the local
regulations
">