TCD-41K Operation Explanation

TCD-41K Operation Explanation
n Explanation of Panel
nCurrent Value
CONCH
■
Set1 Setting
Value
counter/timer
Input Indication
Lamp
Timer Mode, Parameter Value Setup (TIMER MODE)
(Press “MODE” key to start, turn SW-1 to OFF and SW-4 to ON)
Output Time:(tr)
Indication Lamp of
Timing unit
s
m
h
cnt
out
Output Indication
Lamp
mode
RST
MODE Key
mode
4
Disp Key
Timer Mode Setup :(Timer mode)
RST
disp
3
Setting the output hold time of RELAY
Range:0.01 to 9.99 seconds, please press number
key 1,2,3 to setup.
2
Setting the counter to count up, and down. Please
press “1” key for option.
1
Number Key
1~4
mode
1
Name of Key
Function
Enter input setting mode, and swift to parameter
Setup.
Finish setting, and back to counting mode.
Mode
Disp
Number Key1~4
RST
n
CP1 touch to count
up
CP2 stop timing
Timer Unit Setup:
Setting the min. timing unit of timer, please press “1”
for setup.
Used to change parameter value.
99.99 sec.
Display value, RELAY return.
mode
Specification
Power Supply
Power Consumption
Input Frequency
AC 100V~240V， 60/50Hz ±10%
Max. 8VA
25 Hz，2kHz(by SW-5 switch for option)
Inputs
ON Impedance 2kΩ max.
NPN(Non-Voltage) OFF Impedance
100kΩ min.
RELAY Contact Output
Ambient Temperature
Storage Temperature
Relative Humidity
Contact: 5A,240VAC，resistance load(p.f=1).
0 to 55℃ with no icing
-25 to 65℃ with no icing
35% to 85% RH
■
999.9 sec.
s
m
h
1
s
m
h
1
s
m
h
s
m
h
1
s
m
h
1
999.9 min.
99 hour 59 min.
1
s
m
h
999.9 hour
Power-on RESET:
Current value return when setting power input. Press ”1”
key for setup.
mode
(Press “MODE” key to start, turn SW-1、SW-4 to OFF)
1
Memory of
current value
Output Time:(tr)
Setting the output hold time of RELAY
Range:0.01 to 9.99 seconds, please press number
key 1,2,3 to setup.
1
Current value
return
disp
Finish Setting
Counting Scale: (SCALE):
The parameter can change the input signal to actual
physical capacity(volume, and length). For example:
Per pulse of input signal is 0.1mm, and setting the
counting scale to 0.1, the range: 0.001 ~ 9.999.
Please 1 to 4 to change your counting scale.
mode
9999 sec.
s
m
h
99 min. 59 sec.
Counter Mode, Parameter Value Setup
mode
1
CP1 touch to count
Down
CP2 stop timing
n
ON
Explanation of Setting Switch(Located at the rear of
panel)
Parameter Protection (KEY/PRO):
1 2 3 4 5
If turn SW-1 to ON, the “mode” key of panel can’t work.
Then, it is able to modify the protection parameter
value.
Decimal point:
Setting the decimal point positing of current value.
Please press 1,2,3,4 to setup.
mode
RELAY Output Mode Adjustable
Counter Mode Setup:
ON 1 2 3 4 5
Setting the counting up, down and single phase addition &
subtraction of counter. Please press “1” for setup.
mode
N position:
Present Value ≧SET1 Setting Value, RELAY keep
output，press RST key to return.
ON 1 2 3 4 5
1
CP1 counting up
CP2 stop counting
1
CP1 counting down
CP2 stop counting
R position:
Current Value ≧SET1 Setting Value. RELAY output
and return with current value after delaying tr time.
1
CP1 counting up
CP2 counting down
Power-on RESET:
Current value return when setting power input. Press ”1”
key for setup
ON 1 2 3 4 5
ON 1 2 3 4 5
mode
1
Memory of
current value
1
ON 1 2 3 4 5
Current value
return
C position:
Current Value ≧ SET1 Setting Value, RELAY output,
current value delay to return immediately. RELAY return
after tr time。
D position:
Current Value ≧ SET1 Setting Value,，RELAY keep
Output, stop counting/timing and press RST key to
return.
Counter/Timer Mode:
Turn SW-4 to OFF is counter mode, and the cnt lamp of
panel will light. If in ON position, which is timer mode.
disp
Finishing
Setting
ON 1 2
3 4 5
Input Frequency Limited:
Turn SW-5 to OFF(HI), the max. input signal is 2KHz.
And, at ON(LO)，is 20Hz.
TCD-41K Operation Explanation
n
★Noted: Except SW-1, it must to turn on the meter again when
modify the setting.
n
Display
N position
CV
CV
UP COUNT
SET1
DOWN COUNT
SET1
T
T
CP2
RS
OUT
R position
CV
CV
UP COUNT
SET1
DOWN COUNT
SET1
T
T
CP2
RS
OUT
tr
tr
tr
tr
C position
CV
CV
UP COUNT
SET1
DOWN COUNT
SET1
T
T
CP2
RS
OUT
tr
tr
tr
tr
D position
CV
CV
UP COUNT
SET1
DOWN COUNT
SET1
T
T
CP2
RS
OUT
n
Terminal Connector
0V
6
RS
CP2
CP1
7
8
9
11
1
on 1 2 3 4 5
2
3
10
12
4
5
Dimension Diagram

Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project