HUBER+SUHNER SENCITY Link SL60-3001, SL60-4001 wireless link Installation and User Manual

Installation and User Manual

SENCITY

®

Link SL60-3001/SL60-4001

Revision F

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299


We, HUBER+SUHNER AG of Degersheimerstrasse 14, CH-9100 Herisau/Switzerland declare that the product

SENCITY®Link / SL60-3001, SL60-4001 (formerly: SL60-100-57/64-38-E-O) is in conformity – after consultation with the notified body Phoenix Testlab (No. 0700) – with the following standards and normative documents:

●

●

EN 50371 (2002): Generic standard to demonstrate the compliance of low power electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (10 MHz - 300 GHz)

EN 55022 (2006): Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement

●

●

EN 55024 (1998): Information technology equipment - Immunity characteristics - Limits and methods of measurement

EN 60950-1 (2006): Information technology equipment - Safety -- Part 1: General requirements

●

●

●

ETSI EN 302 217-3 (2007): Fixed Radio Systems; Characteristics and requirements for point-topoint equipment and antennas; Part 3: Harmonized EN covering essential requirements of Article

3.2 of R&TTE Directive for equipment operating in frequency bands where simplified or no frequency co-ordination procedures are applied

ETSI EN 302 217-4-2 (2007): Fixed Radio Systems; Characteristics and requirements for pointto-point equipment and antennas; Part 4-2: Harmonized EN covering essential requirements of

Article 3.2 of R&TTE Directive for antennas is in accordance with the following Directives:

R&TTE Directive 1999/5/EC

We hereby declare that the equipment named above has been designed to comply with the relevant sections of the above referenced specifications. The unit complies with all essential requirements of the Directives.

Herisau, January 2008

© 2010 HUBER+SUHNER AG 3


This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

If this product is suspected of causing harmful interference with other equipment, discontinue its operation immediately and contact HUBER+SUHNER.

In order to meet FCC RF Exposure requirements, this device must be installed in such a way that a distance of 2 m is always maintained between the device antenna and nearby persons.

Modifications or substitutions made on the terminal or parts of it without the written approval of

HUBER+SUHNER could void the user’s authority to operate the equipment.

FCC ID: TTDSL60100

IC: 6318A-SL60100

4 www.hubersuhner.com


TABLE OF CONTENTS

1 Introduction

1.1 Intended users

1.2 Revision

1.3 Prior knowledge

1.4 Organisation

1.5 Used symbols

1.6 Safety

1.7 Warranty

1.8 Copyright / Disclaimer

2 System overview

2.1 General description

2.1.1 Benefits

2.1.2 Applications

2.2 System components

2.2.1 Terminals

2.2.2 Alignment bracket

2.2.3 Alignment tool

2.2.4 Ice bridge

2.2.5 Sealed Ethernet connector

2.2.6 Accessories

2.2.6.1 PoE injector (accessory)

16

16

2.2.6.2 Data line protector (accessory) 16

2.2.6.3 Mast bracket (accessory)

2.2.6.4 Ethernet cables (accessory)

3 Site planning

17

17

18

3.1 Terminal location

3.2 Line of sight

3.3 Link distance / Link availability

3.4 Terminal mounting options

19

20

20

21

13

13

14

12

12

12

14

15

15

15

7

7

8

7

7

9

10

10

11

3.4.1 Wall mounting

3.4.2 Pole mounting

3.5 Cabling

3.6 Grounding / Lightning protection

3.7 Co-located applications

4 Installation

4.1 Unpacking

4.2 Mount installation

4.2.1 Wall mount

4.2.2 Mast mount

4.3 Terminal installation

4.4 Cable installation

4.5 Antenna alignment

4.5.1 Alignment Procedure

4.5.1.1 Optical alignment

4.5.1.2 Power level alignment

4.6 Grounding

4.7 Lightning / Surge protector

4.8 Power injector

5 Terminal management and monitoring functions 32

5.1 Web browser interface 33

5.1.1 System overview screen 33

5.1.1.1 Traffic light colors

5.1.2 Password screen

5.1.3 Firmware update screen

33

33

34

5.1.4 Network configuration screen

5.1.5 Radio alignment screen

5.1.6 Network statistics screen

5.1.7 SNMP configuration screen

34

35

35

36

28

29

29

26

27

27

30

30

31

31

21

21

22

22

23

24

24

25

25



5.2 SNMP interface

5.3 Reset-CD

5.3.1 Parameter reset

5.3.2 Firmware upload

A Technical information

A.1 Troubleshooting

A.1.1 Power and network connection

A.1.2 Network configuration

A.1.3 Duplex mismatch

A.1.4 Miss-alignment

A.2 Specifications

A.2.1 Ethernet cable colour code

A.3 Receiver level / Rain / Link distance

A.4 Availability / Rain zone / Link distance

A.4.1 Map of America

42

42

44

41

41

41

47

48

49

49

37

39

40

40

41

A.4.2 Map of Asia and Middle East

A.4.3 Map of Europe

A.5 Accessories order information

B Country specific information

B.1.1 Switzerland, Germany

B.1.1.1 English

B.1.1.2 Deutsch

B.1.1.3 Français

B.1.1.4 Italiano

C Contacts

C.1.1 Technical assistance

C.1.2 Service center / RMA

D Glossary

E Notes

59

60

60

58

58

59

60

61

62

51

53

55

58

58



1 INTRODUCTION

1.1 I

NTENDED USERS

This manual is intended for all installation and service personnel who are involved in the planning, installation, operation and maintenance of SL60-3001 / SL60-4001 equipment.

Please read the complete SL60-3001 / SL60-4001 (SENCITY®Link) manual prior to its unpacking, installation, setup and deployment.

Although the SENCITY®Link is designed for easy installation and setup, optimum performance can be achieved by following the procedures outlined in this manual.

1.2 R

EVISION

HUBER+SUHNER reserves the right to revise this documentation periodically without any obligation to provide notification of such revision or changes. The latest revision can be downloaded on http://www.sl60.com.

1.3 P

RIOR KNOWLEDGE

This manual assumes that the installer has at least a basic experience and understanding of networking equipment, as well as some familiarity with its configuration and operation. The information covered in this manual should be fully understood prior to installation.



1.4 O

RGANISATION

This user manual is organised into chapters as follows:

● Chapter 1: Introduction – Describes general and legal information.

●

●

Chapter 2: System Overview – Contains the technical data and the description of the equipments.

Chapter 3: Site Planning – Summarizes the requirements regarding site and network. This chapter has to be read as preparation for the installation.

Chapter 4: Installation – Describes the recommended installation procedure of the terminal.

●

●

●

Chapter 5: Management and monitoring functions

Appendix A: Presents additional useful technical information like: troubleshooting, weather maps and technical data.

Appendix B: Country specific information ●

●

●

Appendix C: Contacts

Appendix D: Glossary – Helps with the most important abbreviations.



1.5 U

SED SYMBOLS

Danger

Not used

Warning

Risk for human and equipment

Caution

Risk for equipment and functionality

Advice



1.6 S

AFETY

The following general safety precautions must be observed during all phases of operation and service of those products covered in this manual. Failure to comply with these precautions, or with specific warnings elsewhere in this manual, willfully violates standards of design, manufacture and the intended use of the product.

The SL60-3001 / SL60-4001 meets all CE and FCC electrometric radiation safety requirements for radio equipment. However, it is advisable to avoid long-term exposure to the front face of the terminal while operating this equipment.

Outdoor equipment must be properly grounded to provide some protection

against voltage surges and built-up static charges (as illustrated in chapters 4.6

and 4.7).

All electrical and mechanical installations must comply with local and/or national electrical and building codes.

This equipment must not be modified. Neither must any of its component parts be substituted.

1.7 W

ARRANTY

HUBER+SUHNER warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to one year from the date of shipment to the end user.

During the warranty period, and upon proof of purchase, should the product show indications of failure due to faulty workmanship and/or materials, HUBER+SUHNER will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem



necessary to restore the product or components to full operating condition. Any replacement will consist of a new or remanufactured, functionally equivalent product of equal value, and will be offered solely at the discretion of HUBER+SUHNER.

This warranty shall not apply if the product is modified (e.g. warranty seal is broken), misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions.

To obtain services under this warranty, contact HUBER+SUHNER‘s Service Center, referring to your Return

Material Authorization number (see C.1.2). Products must be returned Postage Prepaid. It is recommended

that the terminal be insured when shipped. Any products returned without either proof of purchase or with an outdated warranty will be repaired or replaced and the customer will be billed for parts and labor. All repaired or replaced products will be shipped by HUBER+SUHNER to the corresponding return address ‘Postage

Paid’ (USA only). If the customer specifies some other return destination beyond US borders, the customer shall bear the cost of the return shipment. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

1.8 C

OPYRIGHT

/ D

ISCLAIMER

Copyright © 2010 by HUBER+SUHNER

The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of HUBER+SUHNER.



2 SYSTEM OVERVIEW

2.1 G

ENERAL DESCRIPTION

The SL60-3001 / SL60-4001 system operates as a data link in the unlicensed 60 GHz band between 57 GHz and 64 GHz and delivers a full duplex data rate of 100 Mbps over a distance of up to 800 m (2600 ft).

Measuring only 16 cm × 16 cm (6.3“ × 6.3“), the terminal’s compact size is attained by extensively integrating the active and passive components.

For more detailed technical data see appendix A.2.

2.1.1 Benefits

●

●

Easy installation – The concept of the

SENCITY®Link allows to the end user to install it as easy as any other network component.

The single cable solution reduces the complexity of the installation. The terminal is connected to the network, monitored and supplied with power through a single outdoor rated CAT 5e Ethernet cable.

The visual alignment tool and an alignment bracket allows the user to easily install the link.

Immediate operation without the need of additional configuration is granted.

Network performance – Guaranteed full duplex 100 Mbps along the complete range. Unlike typical

WLAN equipment the user can transmit a full 100 Mbps over the link.



●

●

●

License free operation – The system has been approved and can be operated in many countries.

System administration – To monitor the status and the traffic the user can access the link statistics either via the HTML user interface or by integrating it into a network management tool via SNMP.

Security – The proprietary radio interface does not allow any other system to access the 60 GHz transmitted data.

A high level of data security is inherent in the product via signal absorption by atmospheric oxygen and the use of high gain/narrow beam width antennas.

2.1.2 Applications

●

●

●

●

●

●

●

●

LAN extension

Redundant access

Campus connectivity

Disaster recovery

Wireless backhaul

Centralization of IT infrastructure

Temporary connections during events

Mesh and hub and spoke configuration

2.2 S

YSTEM COMPONENTS

The SL60-3001 / SL60-4001 system is composed of the following components:

● Terminal A and Terminal B

●

●

●

Alignment bracket

Alignment tool

Ice bridge



●

●

Sealed Ethernet connection

○

○

○

Main accessories:

○

PoE injector

Lightning protector

Mast bracket

Ethernet cables

2.2.1 Terminals

The terminals are the main system components. They combine the antenna, transmitter and receiver and are connected to the network via a standard

Ethernet cable with RJ-45 connector.

Power is supplied through the Ethernet cable to the terminal. This will require either a PoE (802.3af) compatible network equipment or an additional PoE injector.

2.2.2 Alignment bracket

The alignment bracket facilitates installation and positioning owing to its independent axis with coarse and fine alignment capabilities.



2.2.3 Alignment tool

The optical alignment tool provided is easily mounted on the terminal using an elastic band. It enables both ends of the link to be aligned quickly, simply and independently.

2.2.4 Ice bridge

The ice bridge offers an additional protection for the terminal against rain, snow and ice-formation.

2.2.5 Sealed Ethernet connector

The seal kit is used to make a watertight connection of the Ethernet coupling. Please use the separate instructions for a proper installation of the seal kit.



2.2.6 Accessories

Please also refer to section A.5.

2.2.6.1 PoE injector (accessory)

The terminal is powered via Ethernet cable according to the IEEE 802.3af

PoE standard. Should the network equipment connected to the

SENCITY®Link does not offer PoE, a power injector can be inserted in line to the Ethernet cable.

2.2.6.2 Data line protector (accessory)

HUBER+SUHNER strongly recommends the installation of an outdoor data line protector to provide lightning and surge protection for the building, personnel and equipment. Please refer to the local and/or national electrical and building codes.

Outdoor

Indoor



2.2.6.3 Mast bracket (accessory)

The mast bracket is used to mount the bracket onto a mast. The bracket is suitable for any pole diameter from 50 mm to 115 mm (2” to 4,5”).

2.2.6.4 Ethernet cables (accessory)

The length of the cable linking the SENCITY®Link to the next network node may be up to 100 m (328 ft) in length. It should, however, be kept as short as practical in order to minimize signal losses. All Ethernet cables must be CAT

5e compliant and suitable for outdoor use. The cable must be UV stable, UL approved and comply with local and/or national building codes.



3 SITE PLANNING

Protector

PoE

Protector

PoE



All installers must perform a full site inspection and plan carefully prior to the physical installation of an SL60-3001 / SL60-4001 system.

This preparation must include:

●

Evaluating the most appropriate location for the installation of the terminal.

● Identifying an appropriate mounting structure (wall or mast) for each terminal.

●

Planning the cable routing from the network component to the terminal.

3.1 T

ERMINAL LOCATION

When selecting the best terminal location the following factors should be considered:

●

Accessibility (e.g. roof)

●

●

●

●

Type of mounting (e.g. wall or pole)

Grounding connection point

Cable runs (max. 100 m / 328 ft)

Line of sight

Use of given protection against sun, rain, etc. will increase the equipment performance.



3.2 L

INE OF SIGHT

To ensure a clear line of sight, there must be no obstructions between the two terminal locations. The

required clearance can be established visually using the following table 1 :

Link distance

100 m

200 m

400 m

(328 ft)

(656 ft)

Boundary diameter

0.7 m

1.0 m

(1312 ft) 1.4 m

(2.3 ft)

(3.3 ft)

(4.6 ft)

600 m

800 m

(1968 ft) 1.7 m

(2625 ft) 2.0 m

(5.6 ft)

(6.6 ft)

Boundary diameter

Link distance

3.3 L

INK DISTANCE

/ L

INK AVAILABILITY

The link distance is directly related to the weather conditions.

The affordable link availability is influenced by the following environmental conditions:

● Rain: the less, the better

●

●

Temperature: the higher, the better

Air pressure: the lower, the better

Knowledge of the link distance (line of sight) is important in estimating link quality.

1 Fresnel zone calculation



For different maps of the world including the rain regions see appendix A.4.

For a more accurate link distance vs. availability calculation please visit http://www.hubersuhner.com/sl60 where you will find an online calculation tool.

3.4 T

ERMINAL MOUNTING OPTIONS

3.4.1 Wall mounting

The wall mounting location should be strong enough to secure the terminal to the wall, taking into account all foreseeable environmental conditions (e.g. wind, rain, ice).

Depending on the material to which the bracket is mounted, differently sized mounting hardware may be necessary.

To mount the terminal onto the bracket use the enclosed M6 bolts. The bracket allows a tilt angle of +/- 50° in both axis.

50°

3.4.2 Pole mounting

The pole mounting kit will be needed to mount the terminal onto poles with diameters from 50 mm to 115 mm

(2” to 4,5”).



3.5 C

ABLING

The terminal is delivered with an Ethernet cable terminated with a RJ-45 plug connector. To connect the

SENCITY®Link to your network, use a CAT 5e Ethernet cable with a maximum length of 100 m to the next network node. Please verify too that the cable used is designed for outdoor environments (e.g. water, solar

UV). Since the power is supplied by the Ethernet cable, please make sure that network equipment used supports Power over Ethernet (PoE). If not, use a PoE injector according to IEEE 802.3af. SENCITY®Link can handle crossover and straight cables.

3.6 G

ROUNDING

/ L

IGHTNING PROTECTION

The terminal must be properly grounded to provide protection against voltage surges.

In the event of a short circuit or lightning strike, effective grounding can prevent damage to building, equipment, infrastructure and personnel. For installations in the USA, refer to Article 830 of the National

Electrical Code (Network-powered broadband communications systems), for all other countries, implement protection in accordance with the safety standards and regulatory requirements of the country in which the equipment is installed.

HUBER+SUHNER strongly recommends the use of outdoor lightning protectors.



3.7 C

O

-

LOCATED APPLICATIONS

Owing to the compact size of the SL60-3001 / SL60-4001 integrated terminal, it is particularly suitable for cosited applications. Possible configurations include:

● Back-to-back - e.g. doubles the link distance

● Parallel link - doubles data capacity or redundancy

● Star - hub and spoke

To deploy a co-sited application, please contact HUBER+SUHNER to assist with devising an appropriate site design.



4 INSTALLATION

Owing to the small size and integrated design of the SENCITY®Link, its correct installation and setup is relatively simple.

Nevertheless, when working on a roof, ladder, mast or staging, please take extreme care, observing all facility and OSHA (or other applicable regulatory agency) required safety precautions.

4.1 U

NPACKING

All equipment and installation material is packed into one box. This is divided into three cartons containing the following items:

● Carton A:

Terminal A ○

○

○

Bracket

Mounting set

●

Carton B:

○

○

○

Terminal B

Bracket

Mounting set

●

○

○

Carton C:

Manual

Reset-CD



●

○

○

Ice bridges

Accessories

Required tools:

○ Adjustable-end wrench

4.2 M

OUNT INSTALLATION

4.2.1 Wall mount

The wall and mounting screws must be able to support a weight of 11 pounds (5 kg), taking into account associated wind and potential ice loading factors.

To ensure the use of the correct screws for the installation, HUBER+SUHNER recommends consulting HILTI’s online Anchor System Advisor at http://www.us.hilti.com/holus/modules/adansel/adas_oview.jsp

Right Wrong



4.2.2 Mast mount

●

●

●

●

Ensure that the mast used has a diameter of between 50 mm to 115 mm (2” to 4.5”).

Use a 13 mm flat wrench (~½”) to fasten the M8 screw nut.

Fasten the alignment bracket onto front part of mast bracket using the enclosed stainless steel screws, nuts and washer (M6).

Fix the front part of the mast bracket and the attached alignment bracket on the mast.

Do not use zinc plated screws as these will corrode and endanger link performance and environment.



4.3 T

ERMINAL INSTALLATION

It is important to install the terminal on the bracket with the same orientation (i.e. antenna polarization) at both ends of the link. The terminal must be mounted on the bracket in such a way that the cable enters it on the same side, top or bottom.

The terminal must be mounted on the bracket by using the allen key with the enclosed stainless steel screws (M6 x 12).

Right

Wrong

Right

Right

Do not use zinc plated screws as these will corrode and endanger link performance and environment.

Positioning the terminal with lateral cable entry will influence heat dissipation.

4.4 C

ABLE INSTALLATION

The length of the cable from the terminal to the next network component may be up to 100 m (328 ft) in length, but should be kept as short as practical in order to reduce signal loss. All Ethernet cables must be CAT 5e compliant and suitable for outdoor use. The cable must be UV stable, UL approved and must comply with local and/or national building codes.



To enter the building, HUBER+SUHNER recommends using cable seals from

Roxtec (http://www.roxtec.com).

4.5 A

NTENNA ALIGNMENT

One of SENCITY®Link’s biggest advantage is its fast, easy alignment procedure.

The terminals can be aligned optically by using the alignment tool. No electrical alignment is required, although possible.

The table below shows the alignment tolerance:

Link distance Alignment accuracy

100 m 328 ft 0.9 m 2.9 ft

400 m 1312 ft 3.5 m 11.5 ft

600 m 1968 ft 5.2 m 17.2 ft

800 m 2625 ft 7.0 m 22.9 ft

Alignment accuracy

Link

dist ance



4.5.1 Alignment Procedure

The following procedure achieves fast, accurate alignment (for all operations, the enclosed 5 mm allen key can be used):

4.5.1.1 Optical alignment

a) Place the alignment tool to the most accessible corner and ensure good visibility to the opposite terminal by rotating the telescope.

b) Loosen the horizontal lock screws (labeled “3”) c) Place the horizontal axis course screw in its middle position (needle).

d) Carry out a rough alignment on the horizontal axis and fasten the screw (labeled “1”).

e) Repeat steps b), c) and d) for the vertical axis.

Horizontal alignment

Wall f) Turn the horizontal course screw (labeled

“2”) by viewing through the telescope and Vertical alignment carrying out the fine alignment.

g) Repeat e) for the vertical axis.

h) If necessary, repeat the fine alignment procedure e) for both axes until the opposite link is correctly aligned.

i) Fasten the lock screw (labeled “3”) on both horizontal and vertical axes.

2 Fine alignment

1 Coarse alignment

3 First lock



4.5.1.2 Power level alignment

Optionally (but recommended), an alignment based on the receiver power level of each terminal can be done. The power level can be accessed via

the web interface (see section 5.1.5).

As described in section 4.5.1.1, it is recommended

to proceed first with a rough horizontal

(respectively vertical) alignment and then to do a fine alignment on each axis. Do not forget to loosen (respectively tighten) the two lock screws before (respectively afterwards).

See chapter A.3 for an estimation of the power

levels at different rain rates and link distances.

A power level of -60dBm is better than a power level of -70dBm

4.6 G

ROUNDING

The terminal must be properly grounded.

Two screws are provided on the reverse housing of the terminal to facilitate the correct grounding. To fasten the grounding cable onto the terminal, use a lug and serrated washer combined with an M8 nut.

Connect the terminal to the connection points nearest to the building-to-earth ground point. The

30

Grounding screws

www.hubersuhner.com


grounding conductor must be as short as is practical and should not exceed 6 m (20 ft). For installations in the USA, refer to Articles 830 of the National Electrical Code (Network-powered broadband communications systems). For installations in all other countries, refer to the safety standards and regulatory requirements.

4.7 L

IGHTNING

/ S

URGE PROTECTOR

HUBER+SUHNER strongly recommends the use of outdoor data line protectors.

To protect humans and the building a protector must be installed before the cable enters the building. For detailed installation instructions, please refer to the dedicated documents enclosed to the protectors:

Outdoor protector 3414.99.0008 84016716

4.8 P

OWER INJECTOR

The power injector is connected inline into the data line. The maximum distance between the PoE and the SENCITY®Link is 100 m (328 ft). The

PoE must be IEEE 802.3af compliant. To check that the injector is functioning correctly, use the PoE Tester (see accessories order information

in section A.5).



5 TERMINAL MANAGEMENT AND MONITORING FUNCTIONS

For an initial configuration, use a PC or laptop. Address the terminal with the appropriate IP address.

Every terminal is labeled with its terminal type (A or B).

The factory default values are:

Terminal IP address

A

B

192.168.0.11

192.168.0.12

Subnet mask User name

255.255.255.0 admin

255.255.255.0 admin

Password sl60 sl60

To communicate with the terminal, ensure that the IP address of the computer used is not allocated automatically by the DHCP server. Configure the IP address manually - e.g. 192.168.0.1 with subnet mask 255.255.255.0.

Remember to ensure that your web browser is not using any proxy server settings.

Note:

The IP address settings have no influence on data connectivity. This settings are only needed to access the terminal monitoring functions of the terminal.



5.1 W

EB BROWSER INTERFACE

5.1.1 System overview screen

This screen shows an overview of key link information including its current status.

5.1.1.1 Traffic light colors

Green:

Yellow:

Red:

System is working correctly

System is working with intermittent detection and synchronization

System is not functional

5.1.2 Password screen

Default user name:

Default password: admin sl60



5.1.3 Firmware update screen

Current firmware can be downloaded from http://www.sl60.com or requested via technical support. The downloaded file should be saved on the local computer and then uploaded to each terminal through the firmware update form on the web interface.

5.1.4 Network configuration screen

The network configuration screen offers the option to change network settings if required. The IP address settings and VLAN settings have no influence on data connectivity.

The “Enable VLAN” check box allows the SL60-

3001 / SL60-4001 terminals to be accessed when the link is integrated into a VLAN trunk. The VLAN

ID needs to be set then too.



5.1.5 Radio alignment screen

The radio alignment screen shows specific details relating to the alignment of the two terminals.

The radio history file does log (once a minute) the following parameter values for the last 48 hours:

●

Time since last reboot

Time format: <days>.<hours>:<minutes>

●

●

Receive power at time XY ("minus" sign omitted)

Device temperature in °C

● Lock detector: if unequal to 1, then the receivers are not locked

The resynchronization button can be used to restart the synchronization process with the far end terminal.

5.1.6 Network statistics screen

The network statistics screen shows standardized information relating to network traffic and errors.

Traffic status information is continuously updated and specific network errors are listed.



5.1.7 SNMP configuration screen

The SL60-3001 / SL60-4001 terminal can be integrated into a network management system by using the implemented SNMP agent. This agent supports GET and TRAP functionality. No setting can be performed via SNMP.

Note:

To use this feature you need an SNMP manager program such as HP OpenView or Castlerock’s SNMPc.

The MIB file can be downloaded directly from the terminal.



5.2 SNMP

INTERFACE

Object OID OID type

MIB-2

(iso.org.dod.internet.mgmt.mib-2.system.x / .1.3.6.1.2.1.1.x) sysDescr sysUpTime sysName

.1.

.3.

.5.

DisplayString

TimeTicks

DisplayString

Description

Includes serial no.

Uptime of the network management set in the web GUI sysLocation .6.

DisplayString set in the web GUI

HUBERSUHNER-MIB sencity

(.iso.org.dod.internet.private.enterprises.hubersuhnerOID.sencity.x / .1.3.6.1.4.1.25358.1.x) sencityLinkQuality .1.

Integer 1: Green

2: Yellow

3: Red sencityReceivePower .10.

Integer Receive signal level [dBm] sencityTemperature sencityLockDetector sencityIfEthernetIn

.11.

.12.

.15.

Integer

Integer

Integer sencityIfEthernetOut sencityIfEthernetInError sencityIfAirIn

.16.

.17.

.18.

Integer

Integer

Integer

Temperature [°C]

Lock detection signal level

Total frames received on the Ethernet interface over a period of 10 seconds.

Total frames sent on the Ethernet interface over a period of 10 seconds.

Total frames dropped due to errors received on the Ethernet interface over a period of

10 seconds.

Total frames received on the Air interface over a period of 10 seconds.



Object sencityIfAirOut sencityIfAirInError

OID

.19.

.20.

OID type

Integer

Integer

Description

Total frames sent on the Air interface over a period of 10 seconds.

Total frames dropped due to errors received on the Air interface over a period of 10 seconds.

Installed firmware version sencityFirmwareversion .21.

String

HUBERSUHNER-MIB sencitytraps

(.iso.org.dod.internet.private.enterprises.hubersuhnerOID.sencity.sencityTraps.x / .1.3.6.1.4.1.25358.1.22.x) sencityLinkQualityImprovedTrap .1.

Integer 1: from red to green

2: from red to orange

3: from orange to green sencityLinkQualityReducedTrap .2.

Integer sencityTemperatureHighTrap sencityTemperatureLowTrap

.3.

.4.

Integer

Integer

1: from green to orange

2: from green to red

3: from orange to red

A trap indicating that the temperature within the terminal is over or below 70 degree

Celcius

A trap indicating that the temperature within the unit is over or below -40 degree Celcius



5.3 R

ESET

-CD

On the Reset-CD following functions are available

● Parameter reset

●

●

Firmware upload

Documents in PDF format

This CD can be indispensable if the terminal IP address is lost or the terminal is on DHCP modus in a network where no DHCP server is available. In those cases, even though the data transmission is not influenced, the terminal monitoring functions are not accessible.

By using the parameter reset functionality it is possible to reset the terminal to the factory default IP

addresses (see 5). Also, if username and/or password are lost, they can be reset using the parameter reset

function (see section 5.3.1) of the CD.

This CD can be indispensable if during the firmware upload process it occurs a power breakdown or the

Ethernet connection breaks. Then it will be needed to upload the firmware via Reset-CD to the terminal.

The Reset-CD is bootable, this means the computer is started by putting the Reset-CD into the optical drive

(NOTE: the optical drive has to be defined on the computer firmware settings as a bootable device). With the

CD a Linux operating system is loaded into the computer memory, so that the communication with the embedded linux of the terminal is enabled.

System requirements:

Intel compatible CPU (i486 or later), 32 MB RAM, CD-ROM drive as bootable device, Ethernet interface.



5.3.1 Parameter reset

The parameter reset function will reset all terminal parameters (e.g. IP address, username, password) to the factory defaults.

5.3.2 Firmware upload

With the firmware upload functionality a firmware can be uploaded to the terminal even the previous installed firmware is lost by power breakdown or

Ethernet connectivity break during firmware upload process.

The CD contains useful documents (manual, installation video, etc.)



A TECHNICAL INFORMATION

A.1 T

ROUBLESHOOTING

This chapter provides solutions to problems that can occur during the installation and operation of the SL60-

3001 / SL60-4001. It covers various aspects of installation and network setup.

Note:

Each of the following points must be checked at both ends of the link. Start by performing the entire procedure on one side (e.g. Terminal A). If this does not solve the problem, repeat all the steps at the opposite terminal.

A.1.1 Power and network connection

You must verify that the terminal is connected to the power. The PoE injector must be installed and plugged in. Go to the terminal, disconnect the RJ-45 connector and verify if there is power in the cable using a standard PoE tester.

Take the cable and plug it into a notebook or a network testing device and verify if there is a correct network connection.

If there is any problem, please replace the cable and validate the connection again. We provide special, preassembled outdoor CAT 5e cables to ensure easy installation.

A.1.2 Network configuration

Check that the IP address is in the same range and subnet as the SL60-3001 / SL60-4001.



Note:

The IP address of the SL60-3001 / SL60-4001 is 192.168.0.11 for Terminal A and

192.168.0.12 for Terminal B. All the computers on the network must have a unique IP address in the same range, e.g. 192.168.0.X. Any computers with identical IP addresses will not be visible on the network.

They must all, therefore, have the same subnet mask e.g. 255.255.255.0.

Do a Ping test to make sure that the SL60-3001 /

SL60-4001 is responding. Go to Start → Run →

Type “Command” → Type “ping 192.168.0.X”.

A successful Ping test will generate four replies.

As soon as the network configuration is correct you can access the GUI (Graphical User Interface) and check the settings according to section 4.9.

A.1.3 Duplex mismatch

If you encounter bad network performance, you probably have a duplex mismatch.

To ensure that the SL60-3001 / SL60-4001 terminal and the connected network component (e.g. switch) do not have a duplex mismatch you must first check your statistics.

If you find many input errors, you are on the full-duplex side; if you see many late collisions, you are on the half-duplex side.

To solve the duplex mismatch, you must manually configure both network components to the same values.

A.1.4 Miss-alignment

See the configuration interface as described in section 5.1.4. On the Radio alignment screen (see section

5.1.5) you see the signal strength in dBm (e.g. -30 dBm). If the value is below -95 dBm the receiver is not in

the correct position to track the signal. You therefore need to re-align the terminal to its opposite terminal



(please follow the instructions in section 4.5.1).



A.2 S

PECIFICATIONS



General system information

● Transmission Capacity: 100 Mbps Full Duplex

●

●

Interface:

Latency:

100 Base-TX

●

●

Range*:

Availability*:

< 50 µs + distance latency (1 µs / 300 m) up to 800 m (2600 ft) up to 99.999%

●

Warranty:

Connection

● Cable Length:

●

Signal Wires:

1 year max. 100 m (300 ft)

CAT 5e

●

Connector:

Mechanical data

●

Dimension:

RJ–45 (male; including outdoor Ethernet seal kit)

162 x 162 x 89 mm

(6.4“ x 6.4“ x 3.5“)

3500 g (7.7 pounds) ● Weight:

System administration

●

Management: SNMP

Web browser-based configuration

Power supply

● Standards:

● Voltage:

Compliant to Power over Ethernet according to IEEE 802.3af

± 48 V DC

●

Power Consumption: 11 W

Environmental data

● Working Temperature **: - 45 °C ... + 55 °C

(- 49 °F … + 131 °F)



●

●

Storage Temperature: - 30 °C … + 55 °C

(- 22 °F … + 131 °F)

Wind Load: operating survival

160 km/h (100 mph)

200 km/h (125 mph)

Regulatory

● Regulatory Compliance:

FCC Part 15

Industry Canada RSS210

R&TTE Directive 1999/5/EC

Ordering information

●

SL60-3001: Item # 84057630

SL60-4001: Item # 84064720 each composed of: 2 Terminals

2 Alignment brackets

1 Manual

2 Mounting sets

1 Reset-CD

2 Ice bridges

* The range depends on the climate zone and the requested availability

** Only if the terminal is powered up



A.2.1 Ethernet cable colour code

Note:

By cutting of the connector the warranty will expire.

6

7

8

3

4

5

Pin

1

2

Name

TX+

TX-

RX+

Power+

Power+

RX-

Power-

Power-

RJ45 Plug

Black

Green

Red

Blue

White

Orange

Yellow

Brown

Twisted pairs:

● Black / Green

●

●

●

Yellow / Brown

Red / Orange

Blue / White



A.3 R

ECEIVER LEVEL

/ R

AIN

/ L

INK DISTANCE

The following diagram shows the approximate receiver levels at different rain rates and distances. This diagram is valid for A and B terminals delivered with firmware version 1.40 or higher.

SL60-3001

SL60-4001



A.4 A

VAILABILITY

/ R

AIN ZONE

/ L

INK DISTANCE

A.4.1 Map of America



The link distance is directly related to the weather conditions. The tables below refer to a link working at a distance of up to 600m (SL60-3001) resp. 800m (SL60-4001), for dry weather conditions.

600m (SL60-3001):

Availability

99%

99.9%

Rain zone *

Link distance (m)

G H J A B C D E F K L M N P Q

598 593 591 576 592 580 569 577 534 582 577 561 554 512 463

577 569 554 534 547 534 512 523 477 512 498 470 429 366 355

99.99% 534 512 498 481 470 450 443 438 429 412 375 370 325 278 304

99.999% 470 438 412 412 358 346 366 340 384 319 274 299 255 221 261

800m (SL60-4001):

Availability

99%

99.9%

Rain zone *

Link distance (m)


797 789 785 764 787 770 752 765 701 772 765 741 730 669 597

765 752 730 701 719 701 669 684 618 669 648 607 549 461 446

99.99% 701 669 648 624 607 578 569 561 549 524 473 466 405 343 376

99.999% 607 561 524 524 450 434 461 425 486 397 338 370 312 268 320

* Rain zone according to ITU-R Recommendation PN.837-1

99.9% availability equates to 526 minutes per year of outage due to heavy rains.





A.4.2 Map of Asia and Middle East




600m (SL60-3001):

Availability

99%

99.9%

Rain zone *

Link distance (m)


598 593 591 576 592 580 569 577 534 582 577 561 554 512 463

577 569 554 534 547 534 512 523 477 512 498 470 429 366 355

99.99% 534 512 498 481 470 450 443 438 429 412 375 370 325 278 304

99.999% 470 438 412 412 358 346 366 340 384 319 274 299 255 221 261

800m (SL60-4001):

Availability

99%

99.9%

Rain zone *

Link distance (m)


797 789 785 764 787 770 752 765 701 772 765 741 730 669 597

765 752 730 701 719 701 669 684 618 669 648 607 549 461 446

99.99% 701 669 648 624 607 578 569 561 549 524 473 466 405 343 376

99.999% 607 561 524 524 450 434 461 425 486 397 338 370 312 268 320







A.4.3 Map of Europe




600m (SL60-3001):

Availability

99%

99.9%

Rain zone *

Link distance (m)


598 593 591 576 592 580 569 577 534 582 577 561 554 512 463

577 569 554 534 547 534 512 523 477 512 498 470 429 366 355

99.99% 534 512 498 481 470 450 443 438 429 412 375 370 325 278 304

99.999% 470 438 412 412 358 346 366 340 384 319 274 299 255 221 261

800m (SL60-4001):

Availability

99%

99.9%

Rain zone *

Link distance (m)


797 789 785 764 787 770 752 765 701 772 765 741 730 669 597

765 752 730 701 719 701 669 684 618 669 648 607 549 461 446

99.99% 701 669 648 624 607 578 569 561 549 524 473 466 405 343 376

99.999% 607 561 524 524 450 434 461 425 486 397 338 370 312 268 320







A.5 A

CCESSORIES ORDER INFORMATION

Item number

23033695

Description

Data Line Protector (indoor)

To use only in combination with an outdoor protector.

84014284 Data Line Protector (outdoor)

84021330 PoE 802.3af Tester



Item number

84021333

84016575

84015652

84016596

Description

PoE 802.3af Power Injector

SENCITY®Link Alignment Bracket

Mast Bracket

Visual Alignment Tool



Item number

84022128

84031068

84028025

84028026

84028029

84034955

84044851

Description

Ice Bridge

Outdoor Ethernet Cable 2 m




Encryption Box HiSec 220

Sealed Ethernet connection RJ45



B COUNTRY SPECIFIC INFORMATION

B.1.1 Switzerland, Germany

B.1.1.1 English

Indication about the correct use of the system

The devices of this system establish a wireless point to point data connection.

Indication about possible application limitations

Operation on NIB / NPB (Non interference basis / non protection basis): The equipment is not permitted to cause harmful interference to other radio services. The equipment has to be switched off immediately in the case of interference with other services.

Indication about the network interfaces to which the system can be connected

The devices are intended to be connected to IEEE standard 802.3af (Power over Ethernet) compliant devices. SL60-3001 / SL60-4001 has to be supplied by a limited power source according to EN 60950-

1:2006.

B.1.1.2 Deutsch

Hinweis auf bestimmungsgemässe Verwendung der Anlage

Die Geräte dieser Anlage stellen eine drahtlose Punkt-zu-Punkt Datenverbindung her.

Hinweis auf mögliche Verwendungseinschränkungen

Interferenzen und Schutzvorkehrungen im Betrieb: Die Ausrüstung ist nicht gestattet, andere Funkdienste nachteilig zu stören. Das Gerät muss im Falle von Interferenzen mit anderen Diensten sofort ausgeschaltet werden.

Hinweis auf die Netzschnittstellen, an welche die Anlage angeschlossen werden kann

Die Geräte sind für den Anschluss an dem IEEE-Standard 802.3af (Power over Ethernet) konforme Geräte



bestimmt. SL60-3001 / SL60-4001 muss durch eine Stromquelle begrenzter Leistung gemäss EN 60950-

1:2006 gespiesen werden.

B.1.1.3 Français

Indication concernant l‘utilisation correcte de l‘installation

L’équipement de cette installation établis une liaison de données point à point sans fil.

Indication concernant de possible restrictions de l‘utilisation

Interférence et protection pendant le fonctionnement: Le matériel n’est pas permis de causer des interférences nuisibles à d’autres services radio. Le matériel doit être mis hors service immédiatement dans le cas d’interférence avec d’autres services.

Indication concernant les interfaces du réseau auxquelles l‘installation peut être raccordé

L’équipement est conçu pour le raccordement aux appareils conformes au standard IEEE 802.3af (Power over Ethernet). SL60-3001 / SL60-4001 doit être alimenté par une source de courant fini selon EN 60950-

1:2006.

B.1.1.4 Italiano

Indicazione concernente l’utilizzo corretto e l’installazione

Le componenti installate di questo sistema creano un ponte radio punto-punto.

Indicazione concernente le possibili restrizioni dell’utilizzo

Interferenze e protezione durante l’utilizzo: il sistema non deve causare alcuna interferenza nociva ad altri servizi radio. Questo sistema deve essere spento immediatamente nel caso di interferenza con altri servizi.

Indicazione concernente le interfacce alle quali il sistema può essere connesso

Il sistema è concepito per essere connesso all’interfaccia conforme allo standard IEEE 802.3af (Power over

Ethernet). SL60-3001 / SL60-4001 deve essere alimentato da un’alimentazione conforme alle specifica EN

60950-1:2006.



C CONTACTS

C.1.1 Technical assistance

Please visit http://www.sl60.com

C.1.2 Service center / RMA

USA / Canada toll free phone number:

1-800-348-9008



D GLOSSARY

DHCP

DNS

CE

Dynamic Host Configuration

Protocol

DHCP enables both manual and automatic IP address allocation in a network.

Domain Name System enables the translation from IP address to domain name

The CE marking is a conformity mark on products placed on market in the European Economic Area.

FCC

IP

LAN

Federal Communication

Commission (USA)

Internet Protocol

Local Area Networks

LOS Line of Sight – uninterrupted, visual, point-to-point contact.

MAC address Media Access Control

OSHA

PoE

QPSK physical, unique address of network component

Occupational Safety and Health

Administration

Power over Ethernet according to

IEEE 802.3af that provides for a standardized power model.

Quadrature Phase Shift Keying

SNMP

TCP

WAN

WLAN

Simple Network Management

Protocol

Transmission Control Protocol

Wide Area Network

Wireless Local Area Network. This typically unlicensed non line of site application operates in the frequency range 2 - 6 GHz according to IEEE 802.11x.



E NOTES



HUBER+SUHNER (Australia) Pty. Ltd.

Unit 6, 4 Skyline Place

Frenchs Forest

Sydney NSW 2086 (Australia)

Telefon: +61 2 8977 1200

Fax: +61 2 9972 7549

E-Mail: [email protected]

HUBER+SUHNER GmbH

Mehlbeerenstrasse 6

Postfach 1263

82019 Taufkirchen (Germany)

Telefon: +49 89 6 12 01-0

Fax: +49 89 6 12 01162


HUBER+SUHNER Electronics Pvt. Ltd.

359, Udyog Vihar, Phase II

Gurgaon 122016

Haryana (India)

Telefon: +91 124 5102701/02/03

Fax: +91 124 5102704


HUBER+SUHNER América Latina Ltda.

HUBER+SUHNER A/S

Avenida Rui Barbosa, 3613 Kirke Værløsevej 14

Alto da Ponte

Sao José dos Campos -

SP 12213 300 (Brazil)

3500 Værløse (Denmark)

Telefon: +45 48 100 500

Fax: +45 48 100 555


Telefon: +55 12 3946 9 500

Fax: +55 12 3946 9 527


HUBER + SUHNER France

21 E, rue Jacques CARTIER

78960 Voisins le Bretonneux (France) HUBER+SUHNER (Canada) Ltd.

2650 Queensview Drive

Suite 206

Ottawa ON K2B 8H6 (Canada)

Telefon: +33 1 61 37 25 55

Fax: +33 1 30 64 73 68


Telefon: +1 613 721 4111

Fax: +1 613 721 8480


HUBER+SUHNER AG

Degersheimerstrasse 14

Postfach

9100 Herisau (Switzerland)

Telefon: +41 71 353 4111

Fax: +41 71 353 4444


Website: www.hubersuhner.com

HUBER+SUHNER (Hong Kong) Ltd.

Suite 1601, 16/F

Chung Nam Building

1 Lockhart Road

Wanchai, Hong Kong (China)

Telefon: +852 2866 6600

Fax: +852 2866 6313


HUBER+SUHNER AB

Knarrarnäsgatan 7

Box 1247

SE 164 28 Kista, Stockholm (Sweden)

Telefon: +46 8 447 5200

Fax: +46 8 447 5201


HUBER+SUHNER (Singapore) Pte. Ltd.

Number 8, Tuas Avenue 5

Singapore 639334 (Singapore)

Telefon: +65 6861 8186

Fax: +65 6861 3316


HUBER+SUHNER (UK) Ltd.

Telford Road

Bicester Oxfordshire OX26 4LA (UK)

Telefon: +44 1869 364 100/101

Fax: +44 1869 249 046


HUBER+SUHNER Inc.

19 Thompson Drive

Essex VT 05452 (USA)

Telefon: +1 802 878 0555

Fax: +1 802 878 9880




HUBER+SUHNER is certified according to

ISO 9001, ISO 14001, ISO/TS 16949 and IRIS.

WAIVER

It is exclusively in written agreements that we provide our customers with warrants and representations as to the technical specifications and/or the fitness for any particular purpose. The facts and figures contained herein are carefully compiled to the best of our knowledge, but they areintended for general informational purposes only.

64 hubersuhner.com

www.hubersuhner.com


HUBER+SUHNER SENCITY Link SL60-3001, SL60-4001 wireless link Installation and User Manual

Assistant Bot

Installation and User Manual

®

Revision F

© 2010 HUBER+SUHNER AG 3

4 www.hubersuhner.com

TABLE OF CONTENTS

© 2010 HUBER+SUHNER AG 5

6 www.hubersuhner.com

1 INTRODUCTION

© 2010 HUBER+SUHNER AG 7

8 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 9

10 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 11

2 SYSTEM OVERVIEW

12 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 13

14 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 15

2.2.6.1 PoE injector (accessory)

2.2.6.2 Data line protector (accessory)

16 www.hubersuhner.com

2.2.6.3 Mast bracket (accessory)

2.2.6.4 Ethernet cables (accessory)

© 2010 HUBER+SUHNER AG 17

3 SITE PLANNING

18 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 19

20 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 21

22 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 23

4 INSTALLATION

24 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 25

26 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 27

28 www.hubersuhner.com

4.5.1.1 Optical alignment

© 2010 HUBER+SUHNER AG 29

4.5.1.2 Power level alignment

30

www.hubersuhner.com

© 2010 HUBER+SUHNER AG 31

5 TERMINAL MANAGEMENT AND MONITORING FUNCTIONS

32 www.hubersuhner.com

5.1.1.1 Traffic light colors

© 2010 HUBER+SUHNER AG 33

34 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 35

36 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 37

38 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 39

40 www.hubersuhner.com

A TECHNICAL INFORMATION

© 2010 HUBER+SUHNER AG 41

42 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 43

44 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 45

46 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 47

48 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 49

50 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 51

52 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 53

54 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 55

56 www.hubersuhner.com

© 2010 HUBER+SUHNER AG 57

B COUNTRY SPECIFIC INFORMATION

B.1.1.1 English

B.1.1.2 Deutsch

58 www.hubersuhner.com

B.1.1.3 Français