Installation Manual - Fire and Electrical Safety Ltd

Installation Manual - Fire and Electrical Safety Ltd
Installation
Manual
Version 1
Cloudway Court
Belton Road
Loughborough
LE11 1LW
Te l: 01509 232651
Fax: 01509 232665
Email: [email protected]
www.clymac.co.uk
PART No.Z-IM1
Clymac
Installation Manual
The Clymac ZM2 & ZP3 analogue addressable fire
alarm systems are both flexible and easy to install.
This pocket sized installation manual is designed to
provide quick reference information at each stage
of your installation.
The manual offers practical system installation
guidance using an easy to follow format. It deals
with the various system architectures using colour
coding to identify the type of connection followed
by individual installation information for each
product.
More detailed guidance is given separately for our
specialist products, interfacing arrangements and
cable types to ensure they are fully explained.
Please make use of our Installation Helpline if
you require any further support. Your call to the
helpline goes directly through to our team of
technical support engineers who are trained to
provide an instant response.
Contents
Wiring guide
Networks and Redcare
3
........................................
6
3a
Addressable equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
...................................................
8
3b
24Vdc conventional alarm equipment
.........................................
10
3c
PSU’s and transformer rectifiers
.......................................................
12
3d
Further equipment
Loop devices
24Vdc alarm devices
Isolators
Equipment information
1
Interfacing
....................................................
Beam detection
18
...............................................
22
..................................
24
.............................................
26
Intrinsically safe equipment
Radio equipment
58
......................
62
....................................
68
14
...............................
Complying with BS 5839 Pt 1
...............
System commissioning
4
Contact details
5
Duct detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Approved cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Panel information
2
ZP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ZM2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Batteries and enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2
Installation helpline 0844 412 1777
Book commissioning 01509 232651
3
1
Wiring guide
Networks and Redcare
Loop devices
24Vdc alarm devices
Isolators
Interfacing
Complying with BS 5839 Pt 1
Beam detection
Intrinsically safe equipment
Radio equipment
Duct detection
Approved cables
4
Installation helpline 0844 412 1777
Book commissioning 01509 232651
5
1
Networks and Redcare
ZP3 standard networks (ZP3-NW1)
REDCARE
BT92A
Enhanced cable (see page at the end of this section)
600 - 1000m total depending on cable type
Spurs, star connections, radials or combinations allowed
Represented by solid purple line
230Vac
230Vac
ZP3 secure networks (ZP3-NW1 and ZP3-NLM)
Enhanced or standard cable (see page at the end of
this section)
PANEL
600 - 1000m between panels depending on cable type
PANEL
Ring connections only
Represented by solid and dotted purple line
Repeat panels (ZP3-RDU/ZM2-RDU)
24Vdc
24Vdc via main panel or PSU, represented by green lines
Data cable from main panel, represented by orange lines
Star, radial or spur connections allowed
REPEAT
Enhanced or standard cable (see page at the end of
this section)
REPEAT
4-core cable should not be used
230Vac
230Vac
Redcare (ZREDCARE...)
24Vdc via main panel or PSU, represented by green line
Two core cable for each signal, represented by orange line
PANEL
PANEL
BT RedCare BT92A block (installed by BT) local to
RedCare box
Analogue lines not exceeding 3 REN can be used
Lines cannot be through PABX systems
Lines that use data cannot be used
Allow 3 weeks once all information is provided to Clymac
6
Installation helpline 0844 412 1777
Book commissioning 01509 232651
7
1
Loop devices
Lift
Addressable detection loops
ZP3 is available with 1, 2 or 4 loops, ZM2 with
1 or 2 loops
RLY
All devices colour coded blue in further sections can be
connected to these circuits
LED
Cable should be Standard or Enhanced (see page at the
end of this section)
Spurs off the loop are possible without special
bases/devices, subject to agreement with all parties
Basic rules for loop design;
1 127 address maximum, 1 device = 1 address
(combined sensor/sounder = 2 addresses)
Sprinkler
INT
2 1km or 2km maximum (loop powered sounders =
1km) Based on 1.5mm 2 core cable
3 Continuous screen preferably not connected to
building earth
4 Use of 4 core approved by Clymac help line
5 300mm separation from high voltage cables
230Vac
6 Remote LED’s can not be connected to sounder bases
7 Maximum of 16 isolators per loop ZP3,
11 per loop ZM2
8 ZM2 is not compatible with;
A) Radio equipment
B) Intrinsically safe equipment
C) Multi sensors (Z832)
Key
D) Conventional zone/detector interface
Short circuit isolator
Addressable sensor
Addressable manual
call point
Addressable sensor
and sounder
A) Sounder bases - 60 number per loop; or
RLY
Addressable relay
B) Sounder/beacon bases - 40 number per loop; or
INT
Addressable interface
C) Horn sounders - 40 number per loop; or
Addressable sounder
Addressable sensor and
sounder beacon
Addressable sounder
and beacon
8
Installation helpline 0844 412 1777
9 Addressable sounders;
D) Horn sounder/beacons - 25 number per loop; or
E) Beacons - 60 number per loop
Book commissioning 01509 232651
9
1
24Vdc alarm circuit schematic
24Vdc Conventional alarm circuits
ZP3 available with 4 circuits, ZM2 with 2 circuits
Further circuits added by using Z752 interface or 8 way
auxiliary boards (ZP3 only)
All devices colour coded red in further sections can be
connected to these circuits
Enhanced or standard cable (see page at end of
this section)
LSU
Strictly radial connection only, no spurs
LED
End of line resistor fitted in last device on each circuit
3-core
230vac
PSU
Key
Short circuit isolator
Sprinkler
Addressable manual
call point
Lift
Addressable sensor
RLY
Addressable relay
INT
Addressable interface
24Vdc sounder
LSU
RLY
INT
230Vac
*
Loop
in
Addressable sounder
interface
closest to control panel to be installed on
* Sounder
dedicated circuit
Loop
out
Screen
-
+
+
+
-
+
+
-
PSU
10
Installation helpline 0844 412 1777
Book commissioning 01509 232651
11
1
Isolator schematic
Short circuit isolators (Z760, Z60D or Z7-IB)
Fitted to the loops (blue circuits)
Roof space
Maximum 16 per loop ZP3, maximum 11 per loop ZM2
(arrangement assumes no structural separation)
Do not take an address
Not to be fitted to spurs, loop only
ZDIN2
Enclosure
Ideally not concealed from view
Distributed as shown;
Lift
Note B
A) Sounder nearest the panel
2nd Floor
B) Each change of floor within 5 devices
C) Every 32 trigger devices
D) Every 2000msq
Key
Note C or D
Short circuit isolator
1st Floor
Combined sensor
and isolator
DIN mounted isolator
Note A
Note B
Addressable sensor
and sounder
Addressable sensor
230Vac
Addressable manual
call point
I1
DIN mounted output
contact
Addressable manual
call point c/w isolator
Addressable sounder
Ground Floor
12
Installation helpline 0844 412 1777
Book commissioning 01509 232651
13
1
Interface connections
24Vdc door holders
230Vac door holders
Loop
out
Loop
in
E
L
N
24Vdc Doors
Screen
230V
door
holders
1 3 2
-
+
6 4 5
Output
+
N/O
N/C
C
-
LNE
P+ P- P+ P- Screen Screen
Z750
ZN/17
230Vac
Loop
in
Loop
out
Z51D
Input monitoring - eg sprinklers
24Vdc door holders
Loop
in
Loop
out
24Vdc Doors
Sprinklers
+ -
Screen
-
+
N/O
N/C
C
DC Output
Clean Contact
C1 C2
P+ P- P+ P- Screen Screen
230Vac
Z750
+-
LNE
ZN/16 or 18
Loop
in
Loop
out
Z45D
14
Installation helpline 0844 412 1777
Book commissioning 01509 232651
15
1
Interface connections
Output contact - eg Gas valve (230Vac)
Input monitoring
eg fire/fault from remote system
Loop
in
E
L
N
Loop
out
230V
door
holders
1 3 2
6 4 5
Screen
-
+
Remote
System
+
-
P+ P- P+ P- Screen Screen
Loop
in
Z740
Loop
out
Z51D
Output contact - eg lift
Conventional zone
Lift
C
Loop
in
Zone
N/O N/C
Important!
Contact only
rated 30Vdc 1A
PSU
P+ P- P+ P- Screen Screen
++
-
-+
24V
Box
Loop
in
Loop
out
Z50D
16
Installation helpline 0844 412 1777
Lid
ZP3 ONLY
Z570
Book commissioning 01509 232651
17
1
Complying with BS 5839 Pt 1
200mm
Trunking
100mm deep
300mm
Strip light
150mm deep
200mm
300mm
Trunking
light
Detectorsdeep
should be mounted twice theStrip
depth
of any obstructions such
100mm
150mm
as beams, ductwork or light fittings less
than deep
250mm in depth.
1.2m
MCP’s at least 15mm proud of wall and 1200mm above floor.
600mm/150mm
600mm/150mm
Smoke/beam600mm/150mm
detector
distance from600mm/150mm
ceiling
= 25mm to 600mm.
600mm/150mm
600mm/150mm
Heat detector distance from
ceiling = 25mm to 150mm.
If < 300mm
consider as
reaching the
If < 300mm
ceiling
consider as
reaching the
ceiling
Racking
If > 10% of
ceiling height
consider as
> 10% of
aIf wall
ceiling height
consider as
a wall
Racking
Top 10% of void
Top 125mm of void
Top 10% of void
Top 10% of void
Top 125mm of void
Top 125mm of void
Detectors in unventilated voids to be mounted in the top 10% or
125mm, whichever is greatest.
500mm
500mm
500mm
500mm
500mm
500mm
Partitions or racks within 300mm
of ceiling to be treated as full
height.
Structural beams greater than
10% of ceiling height to be
treated as wall.
Applies to point detection and beam detection.
1m
Detectors should not be mounted within 500mm of obstructions such as
walls, beams or ductwork greater than 250mm in depth.
1m
Detectors should be mounted minimum of 1 metre away from a forced
ventilation system.
Flue
Accommodation
1.5m
18
Installation helpline 0844 412 1777
1.5m
Book commissioning 01509 232651
Rack
Rack
1.5m
19
1
Complying with BS 5839 Pt 1
Flue
Accommodation
800mm
Ceiling void
1.5m
1m
1.5m
Rack
Room
Rack
1.5m
Any area covered by automatic detection that contains a horizontal void
of 800mm or more in height, automatic fire detection should also be
provided in the void.
500mm clear space to be maintained below each detector.
Flue
Accommodation
1.5m
1.5m
1.5m
A detector should be mounted within 1.5m away from a vertical shaft such
as a lift at each level. A detector should also be fitted at the top of the
shaft (Excludes L4, L5 & P2).
Office
Duct
T
450mm
350mm
Areas
not covered
R
Beams not to run closer than 500mm to any wall, partition or obstruction.
20
Installation helpline 0844 412 1777
Book commissioning 01509 232651
21
1
Beam detection
Addressable and conventional versions of the beam detector
are available. The following notes describe the connections
for both.
Rx
Rx
Rx
Rx
Rx
Rx
Tx
Tx
Tx
Tx
Tx
Tx
Tx
Tx
Tx
Tx
Tx
Tx
Rx
Rx
Rx
Rx
Rx
Rx
Transmitter end
(Red label)
Receiver end
(Blue label)
110mm
Architecture for loop powered beams (ZLP2000)
10-100m
60mm
35mm
Vertical
alignment
Horizontal
alignment
70mm
Terminate to local conduit box;
Screen: Screen (not to building earth)
Red: Brown
Blue: Black
Yellow: Grey
230Vac
Terminate to local conduit box;
Screen: Screen (not to building earth)
Red: +/Brown
Blue: -/Blue
5-100m
In Out
Terminate to local conduit box;
Screen: earth lug located in
conduit box
Brown: + Rx
Black: 0V Rx
Grey: Signal Rx
260mm
Controller
Loop in and out
required for both
Z2000 and ZLP2000.
When the Z2000 is used
an additional 24Vdc
supply is required.
Local 24Vdc
supply (Z2000) or
addressable loop
(ZLP2000)
Z760 short circuit isolator
Tx High level transmitter
In
Out
In
210mm
Out
Z2000
only
24Vdc
Rx Low level controller connected via dedicated 3 core to
high level receiver
Notes
Loop
Controllers mounted low level
Even distribution throughout the loop
Internal connections
Connection
Loop +
Loop -
Loop
screen
Conventional
Z2000*
Z45D
Z45D
Z45D
Addressable
ZLP2000
Loop +
Loop -
Screen
24V +
24V -
Earth
N/A
N/A
6 beams maximum with 1km loop length
(No loop powered sounders)
6 isolators maximum
Supply + Supply N/A
* Contact installation helpline for advice on system architecture.
22
Key
Installation helpline 0844 412 1777
All mounted 300mm - 600mm from the ceiling
See BS siting section
See isolator section
Book commissioning 01509 232651
23
1
Intrinsically safe equipment
DX070
ZP-ZB
125mm
107mm
MTL5025
150mm
104mm
115mm
35mm
Din rail
16mm
12.5mm
157mm 175mm
ZP-LC
75mm
55mm
Ex MCP & Sensors
8 6/7 5
Screen -- ++
Ex Device
ZP-LC
Loop
in
1
ZP-ZB
++ -- Screen
EX Sounder
2
MTL5025
(GI)
1 2/3 4
11
Loop
out
12
24Vdc
alarm
I.S. earth
(see note)
LC
ZB
GI
GI
Hazardous
area
I.S. earth Note
The zenner barrier requires a dedicated/I.S. earth. In principal
this earth cable must not exceed 1 ohm between the barrier
and the main incoming earth for the building. In addition to
this the cable must be clearly identified by markers. It is also
advisable to include a second cable for continuity checks
during service visits. Clymac’s recommendations are therefore:
Two number 4mm earth cables to the main earthing point
for the building
Both cables identified at regular intervals and either side
of wall penetrations
Notes
All barrier equipment must be installed outside the
hazardous zone
One line conditioner can drive eight addresses
One line galvanic isolator can drive either one I.S. beacon
or two I.S. sounders. The output produced by the sounder
is relatively low
This equipment is made from non conductive material.
The installer and user should ensure it is not installed in
areas that would lead to a build up of electrostatic charge
such as areas with high pressure steam
Cleaning of equipment should be with a damp cloth
The sounder circuits in the hazardous area not monitored
for fault
Screens used for alarm circuits and detector circuits must
not be connected to building earth via conduit boxes or
switch boxes
ATEX Ex II1G
Key
I.S. conventional sounder
Addressable sensor
I.S. addressable sensor
Addressable manual
call point
I.S. addressable manual
call point
230Vac
ZB
LC
Line conditioner (ZP-LC)
Zenner barrier (ZP-ZB)
GI
Galvanic isolator
(MTL5025)
24Vdc alarm sounder
24
Installation helpline 0844 412 1777
Addressable sounder
I.S. conventional beacon
Book commissioning 01509 232651
25
1
Radio equipment
Ceiling
Wall
400mm
ZR472 2 way unit i.e
sensors, MCP’s and
sounders. This type of
unit must have an auxiliary
PSU, as indicated.
150mm
ZR471 1 way unit i.e
sensors and MCP’s only.
This type of unit can
run without an auxiliary
PSU, dependant on
loop load. Contact
installation helpline for
further information.
160mm
55mm
900mm
Terminations
260mm
1 2 3 4 5
Radio
interface
360mm
Terminations
230Vac
1 Loop +ve’s
PSU
ZR472
ZR471
2 Loop -ve’s
3 Loop screen’s
IU
4 24Vdc
5 0V
Earth from PSU terminated to 5A connector block.
230Vac
Radio module
The module and aerials should not be located within
2m of photocopiers, computers, fax machines and other
electrical equipment
The aerials should not be mounted within 400mm of any
metal objects/equipment
Key
Cables should not run directly behind the aerials
Wired addressable sounder
Radio addressable sensor
10m of coaxial cable is supplied with the whip aerial
Wired addressable sensor
A radio survey is required to finalise the locations of all
radio devices and aerials. Please contact the helpline
Wired addressable manual
call point
Radio addressable manual
call point
26
Installation helpline 0844 412 1777
Radio addressable sounder
Book commissioning 01509 232651
27
Duct detection
AIR FLOW
1
Duct
Z-DPU Duct Detector
Z-DPU Duct Detector
Clymac use two types of duct detector as shown. Both use
the same principles of positive and negative pressure to
force a sample through the detector, as such some common
rules apply;
244mm
1 Three times the width of the duct away from any bend,
branch or reducer
+- -+-+
LED Detector
144mm
2 Designed to work with linear air flow 1m/s - 8m/s
3 The body of the detector must be completely sealed
85mm
Z-DPU Duct Detector
600mm
1 Designed to be fixed directly to the flat surface of
the duct
32mm
2 To help achieve a good seal the unit comes complete
with; rear gasket, rubber strip between connection/
detection chambers
50mm
245mm
3 Use knockouts provided for cable entry
4 When modifying the pipes to fit the duct each must be
proportionally reduced.The inlet pipe will require a 32mm
UPVC end cap (glued on). The outlet must be cut at a
40 degree angle
Duct
AIR FLOW
Z-DPU/FH Duct Detector
Z-DPU/FH Flexible Hose Duct Detector
1 Designed to be fixed away from the duct
Z-DPU/FH Duct Detector
180mm
2 To help achieve a good seal the enclosure is designed to
be fixed to the surface using the same fixing centres as
the lid
100mm
8 = - ves
7 = screen
130mm
5 = + ves
3 All cable entries must be sealed with suitable glands
4 Each entry into the duct requires a 32mm hole. This is
sealed with the 32mm ribbed grommets supplied
5 Inlet & outlet should be inline and approx 450mm apart
Outlet
Inlet
AIR FLOW
Duct
Z-DPU Duct Detector
28
Installation244mm
helpline 0844 412 1777
+- -+-+
Book commissioning 01509 232651
29
1
Approved cables
Standard cables
Enhanced cables
Manufacturer
Name
Manufacturer
Name
AEI Cables Ltd (Durham)
Firetec Multicore LSZH
AEI Cables Ltd (Durham)
Cavicel SpA
Firecel SR/114 H
Firetec Enhanced Multicore
LSZH
Doncaster Cables
Firesure
Cavicel SpA
Firecel SR/114 E
Draka UK Ltd
Firetuf Plus
Irish Driver-Harris
Company Ltd
Kilflam 3000
Pirelli Cables Ltd
FP Plus
Draka UK Ltd
Firetuf EMC
Haani Cables Ltd
Firecool
Irish Driver-Harris
Company Ltd
Kilflam 2000
Pirelli Cables Ltd
FP200 Gold LSOH
Pirelli Cables Ltd
FP200 Plus Flex
Pyrotenax Mic (light duty)
Pirelli Cables Ltd
FP400
Tyco Thermal Controls
Canada Ltd
Tratos Cavi SpA
Fire-safe TW950
Ventcroft Ltd
Noburn Diamond
Tyco Thermal Controls
Canada Ltd
Pyrotenax PYRO-S
Wrexham Mineral Cables
Wrexham Mic
Ventcroft Ltd
Noburn Platinum
Suitable for;
1 Secure networks when cable routes are diverse
2 All other circuits excluding standard networks, where the
building has a sprinkler system or;
A) Is less than 30m high; or
B) Is going to be evacuated in 1, 2 or 3 phases; or
Suitable for;
1 Standard networks
2 Should be used on all circuits, where the building has
no sprinkler systems and;
A) Is more than 30m high; or
B) Is going to be evacuated in 4 or more phases; or
C) People will remain in occupation during a fire
C) No people will remain in occupation during a fire.
3 Enhanced cable may also be required as part of a
specification or on basis of a risk assessment
4 The Pirelli FP400 cable compiles with BS6387 C, W and Z.
At the time of writing no LCPB approved standard or
enhanced grade cable with an armour was available.
Also, in the absence of a screen the armour should be
used. It should be noted that all efforts to avoid
interference need to be made and ELV ducts must be
used. Limited use only, please contact the help line
5 The Draka Firetuf EMC should be used in applications
where a risk of electrical or radio interference is
anticipated, such as Airports
30
Installation helpline 0844 412 1777
Book commissioning 01509 232651
31
2
Panel information
ZP3
ZM2
Batteries and enclosures
32
Installation helpline 0844 412 1777
Book commissioning 01509 232651
33
2
ZP3 panel
ZP3-FC - Flushing collar
Loops
Height
Width
Depth
Supply
0
647mm
512mm
20mm*
N/A
* Depth of panel once recessed
Wall cut out size:
570mm
Height
Width
440mm
Depth
120mm
ZP3-1-240 - Single loop panel
Loops Height
1
Width
Depth
Supply
Loop
24V alarm
Terminations Terminations
540mm 410mm 137mm 230Vac See diagram
0.75A
A
See diagram
B
ZP3-2-240 - 2 loop panel
Loops Height
2
Width
Depth
Supply
Loop
24V alarm
Terminations Terminations
540mm 410mm 137mm 230Vac See diagram
0.75A
A
ZP3-RDU-B - Repeat panel
Loops
Height
Width
Depth
Supply
0
220mm
360mm
60mm
24Vdc 90mA
See diagram
B
ZP3-4-240 - 4 loop panel
Loops Height
4
Width
Depth
Supply
Loop
24V alarm
Terminations Terminations
540mm 410mm 137mm 230Vac See diagram
0.75A
A
See diagram
B
Top entry
Diagram A
Loop Terminations
Back entry
Mains
Out
Loop 1
In
+ - screen + - screen
Loops
Alarms
Diagram B
24V Alarm Terminations
Battery
Battery
Sounder 2 Sounder 1
+ - screen + - screen
34
Installation helpline 0844 412 1777
Book commissioning 01509 232651
35
2
ZM2 panel
ZM2-RDU-L0 - Surface repeat panel
Loops
Height
Width
Depth
Supply
0
255mm
245mm
75mm
24Vdc 170mA
ZM2-1L - Single loop panel
Loops Height
1
Width
Depth
Supply
Loop
24V alarm
Terminations Terminations
465mm 365mm 110mm 230Vac See diagram
0.6A
A
See diagram
B
ZM2-2L - 2 loop panel
Loops Height
2
Width
Loops
Height
Width
Depth
Supply
0
255mm
245mm
35mm*
24Vdc 170mA
* Depth of panel once recessed
Depth
Supply
Loop
24V alarm
Terminations Terminations
465mm 365mm 110mm 230Vac See diagram
0.6A
A
Diagram A
Loop Terminations
ZM2-RDU-FL0 - Flush repeat panel
See diagram
B
Wall cut out size:
Height
219mm
Width
213mm
Depth
54mm
Diagram B
24V Alarm Terminations
+ + Out
Return
Loop
+
+
-
B
B
NAC1
NAC2
ZM-TRIM1 - Flushing collar
Loops
Height
Width
Depth
Supply
N/A
539mm
445mm
40mm*
N/A
Top entry
* Depth of panel once recessed
Alarms
Side entry
Mains
Wall cut out size:
Height
495mm
Width
395mm
Depth
70mm
Loops
Battery
36
Battery
Installation helpline 0844 412 1777
Book commissioning 01509 232651
37
2
Batteries and enclosure
ZM2-18-E
Loops
Height
Width
Depth
Supply
N/A
400mm
400mm
110mm
N/A
ZM2-24-E
Loops
Height
Width
Depth
Supply
N/A
400mm
400mm
200mm
N/A
Z3-40-E
Loops
Height
Width
Depth
Supply
N/A
250mm
450mm
200mm
N/A
38
Installation helpline 0844 412 1777
Book commissioning 01509 232651
39
3
Equipment information
Addressable equipment
24Vdc conventional
alarm equipment
PSU’s and transformer rectifiers
Further equipment
40
Installation helpline 0844 412 1777
Book commissioning 01509 232651
41
3a
Bases/1st fix plates
Z7SB-1 - Surface sensor base
Z760-SB - Surface isolator base
Diameter
Depth
Loop Positive
Loop Negative
Screen
Diameter
Depth
Loop Positive
Loop Negative
Screen
108mm
18mm
5
8
7
108mm
18mm
5
6 and 8
7
Unit designed to be fixed to conduit
box or similar with fixing centres
50-90mm apart.
Unit designed to be fixed to conduit
box or similar with fixing centres
50-90mm apart.
Devices should have two fixings in the
conduit box to avoid the base spinning
around when the heads are installed.
Devices should have two fixings in the
conduit box to avoid the base spinning
around when the heads are installed.
Remote LED connection + on 2, - on 3.
Fit temporary link between 6 and 8
for commissioning.
Z7RB-1 - Recessed sensor base
Z760-RB - Recessed isolator base
Diameter
Depth
Loop Positive
Loop Negative
Screen
Diameter
Depth
Loop Positive
Loop Negative
Screen
116/138mm
38mm
5
8
7
116/138mm
38mm
5
6 and 8
7
Unit designed to be fixed to conduit
box or similar with fixing centres
50-90mm apart.
Unit designed to be fixed to conduit
box or similar with fixing centres
50-90mm apart.
Devices should have two fixings in the
conduit box to avoid the base spinning
around when the heads are installed.
Devices should have two fixings in the
conduit box to avoid the base spinning
around when the heads are installed.
Remote LED connection + on 2, - on 3.
Fit temporary link between 6 and 8
for commissioning.
120mm clearance hole, ceiling <25mm.
Z7-IB - Combined sensor base & isolator
Z755SPB - Sounder 1st fix plate
Diameter
127mm
Depth
Loop Positive
47mm
5
Loop Negative
6
Screen
7
Unit designed to be fixed to conduit
box or similar with fixing centres
50-90mm apart.
Diameter
Depth
Loop Positive
Loop Negative
Screen
109mm
23mm
5
6 and 8
7
Used instead of detector base
(Z7SB-1).
Devices should have two fixings in the
conduit box to avoid the base spinning
around when the heads are installed.
Common mounting plate for all
addressable sounders. Dimensions
shown include base but not horn.
No remote LED connection.
W = white. R = Red.
42
Installation helpline 0844 412 1777
Book commissioning 01509 232651
43
3a
Detectors
Z710 - Ionisation sensor
Z732 - Optical heat sensor
Diameter
Depth
Loop Positive
Loop Negative
Screen
Diameter
Depth
Loop Positive
Loop Negative
Screen
106mm
52mm*
N/A
N/A
N/A
106mm
58mm*
N/A
N/A
N/A
* Depth dimension excludes base.
* Depth dimension excludes base.
Suitable bases
Z7SB-1
Z7RB-1
Z755BV
Z755B
Z7-IB
Suitable bases
Z7SB-1
Z7RB-1
Z755BV
Z755B
Z7-IB
Only for use on ZP3.
Z832 - Multi sensor
Z720 - Heat sensor
Diameter
106mm
Depth
Loop Positive
52mm*
N/A
Loop Negative
N/A
Screen
N/A
Diameter
Depth
Loop Positive
Loop Negative
Screen
106mm
58mm*
N/A
N/A
N/A
* Depth dimension excludes base.
* Depth dimension excludes base.
Suitable bases
Z7SB-1
Z7RB-1
Z755BV
Z755B
Z7-IB
Suitable bases
Z7SB-1
Z7RB-1
Z755BV
Z755B
Z7-IB
Only for use on ZP3.
ZLP200 - Addressable beam detector
Z730 - Optical sensor
Port
Depth
Diameter
Depth
Loop Positive
Loop Negative
Screen
Tx
110mm
106mm
52mm*
N/A
N/A
N/A
RX
110mm
Controller
90mm
* Depth dimension excludes base.
Suitable bases
Z7SB-1
Z7RB-1
Z755BV
Z755B
Z7-IB
44
Installation helpline 0844 412 1777
Height
Width
Diameter
60mm
60mm
260mm
210mm
See diagram on page 22.
Book commissioning 01509 232651
45
3a
Detectors
Z-DPU - Duct detector
Height
Width
Depth
144mm
244mm
85mm
Loop Positive Loop Negative
+,+
-,-
Screen
*
* Terminate screens to 5 Amp connector
block or similar
See diagram on page 28.
Z-FH/DPU - Duct detector
Height
130mm
Width
Depth
180mm 110mm
Loop Positive Loop Negative
5
8
Screen
7
See diagram on page 28.
46
Installation helpline 0844 412 1777
Book commissioning 01509 232651
47
3a
Manual call points
Z785-3 - Manual call point (MCP)
Height
93mm
Z785B - Surface box
Width
Depth
Loop Positive
Loop Negative
89mm
28mm
1 and 3
2 and 4
Screen
*
Height
89mm
Width
Depth
Loop Positive
Loop Negative
Screen
89mm
32mm
N/A
N/A
N/A
* Terminate screens to 5amp connector
block or similar (not to building earth).
Can be semi recessed or surface
(with Z785B).
Do not over tighten.
Do not foul the test key entry at the
bottom of the unit.
Shallow switch boxes OK.
Supplied with 2 number 30mm
M3 screws.
Z785K - Keyswitch manual call point
Height
93mm
Width
Depth
Loop Positive
Loop Negative
Screen
89mm
28mm
Red
Black
*
Loop Positive
Loop Negative
Screen
Left
Right
*
* Terminate screens to 5amp connector
block or similar (not to building earth).
Can be semi recessed or surface
(with Z785B).
When semi recessing 35mm switch
boxes should be used.
TOK 003 keys used, supplied with
2 number 35mm M3 screws.
Z787 - IP67 manual call point
Height
124mm
Width
Depth
124mm 80mm
* Terminate screens to 5amp connector
block or similar (not to building earth).
Surface only with surface cable
installation. Top and bottom 20mm
glands used to retain IP67.
48
Installation helpline 0844 412 1777
Book commissioning 01509 232651
49
3a
Sounders/visual
Z755HA-2 - Sounder
Z755BV - Sounder beacon base
Diameter
Depth
Loop Positive
Loop Negative
Screen
Diameter
Depth
Loop Positive
Loop Negative
Screen
127mm
112mm
N/A
N/A
N/A
127mm
47mm
N/A
N/A
N/A
Units available in white or red and are
designed to fit to same colour base
(Z755SPB). Horns can be locked with
removable clip.
Designed to fit Z755 SPB.
Z755HAV-2 - Sounder beacon
Z755V - Beacon
Diameter
Depth
Loop Positive
Loop Negative
Screen
Diameter
Depth
Loop Positive
Loop Negative
Screen
127mm
112mm
N/A
N/A
N/A
106mm
52mm
N/A
N/A
N/A
Loop Positive
Loop Negative
Screen
+ve loop
-ve loop
Screen
Units available in white or red and are
designed to fit to same colour base
(Z755SPB). Horns can be locked with
removable clip.
Unit designed to fit into detector
surface base (Z7SB-1).
Z755B - Sounder base
Z755WP - IP65 sounder
Diameter
Depth
Loop Positive
Loop Negative
Screen
Height
127mm
47mm
N/A
N/A
N/A
127mm
Designed to fit Z755 SPB.
50
Installation helpline 0844 412 1777
Width
Depth
127mm 135mm
Use 20mm glands top, bottom, back
or side for IP rating. Use the holes
provided for fixing.
Book commissioning 01509 232651
51
3a
Isolators
Z760 - Isolator
Z785PT - Manual call point extension
Diameter
Depth
Loop Positive
Loop Negative
Screen
106mm
30mm*
N/A
N/A
N/A
* Depth dimension excludes base.
Height
87mm
Width
Depth
Loop Positive
Loop Negative
Screen
87mm
24mm
P+
P-
Screen
For use with Z60D when an isolator is
required inside the manual call point.
For use with Z760-SB or RB
(see bases).
Loop cables must be rear entry.
It is advisable that this unit is fixed to
fully recessed switch box or similar.
Z7-IB - Surface base and isolator
Diameter
Depth
Loop Positive
Loop Negative
Screen
109mm
23mm
5
6 and 8
7
Used instead of detector base
(Z7SB-1).
Z60D
Height
78mm
Width
Depth
Loop Positive
Loop Negative
Screen
85mm
28mm
P+
P-
Screen
For use with ZDIN/ZDIN2 not in
3rd party equipment.
52
Installation helpline 0844 412 1777
Book commissioning 01509 232651
53
3a
Interface equipment
Z750 - Output contact
Z570 - Zone interface
Height
Width
Depth
Loop Positive
Loop Negative
Screen
120mm
120mm
40mm
N/A
N/A
N/A
Surface mounted with normally 3
number glands required. Entry top or
back only.
Height
80mm
Width
Depth
Loop Positive
Loop Negative
Screen
120mm
55mm
N/A
N/A
N/A
Surface only with normally 4 number
glands required.
Change over contact 30Vdc at
1.5amp.
Best mounted in PSU and left open
due to space within the unit for
installation.
For connections see page 14.
For connections see page 17.
Z740 - Interface
Z45D - DIN interface
Height
Width
Depth
Loop Positive
Loop Negative
Screen
120mm
120mm
40mm
N/A
N/A
N/A
Surface mounted with normally 3
number glands required. Entry top or
back only.
Height
78mm
Width
Depth
Loop Positive
Loop Negative
Screen
45mm
28mm
P+
P-
Screen
Designed to fit into ZDIN/ZDIN2.
Monitors clean contacts.
For connections see page 15.
Monitors clean contacts.
For connections see page 16.
Z752 - Sounder interface
Z745 - Mini interface
Height
Width
Depth
Loop Positive
Loop Negative
Screen
120mm
120mm
40mm
N/A
N/A
N/A
Height
55mm
Width
Depth
Loop Positive
Loop Negative
Screen
51mm
14mm
L+
L-
Screen
Surface mounted with normally 5
number glands required to terminate
to this interface.
Designed to fit in to PSU or accessory
box and has one hole for fixing
purposes.
Up to 3 number top entry and the rest
must be rear entry via conduit box or
similar.
Monitors clean contacts.
For connections see page 10.
54
Installation helpline 0844 412 1777
Book commissioning 01509 232651
55
3a
Interface equipment
Z51D - Output contact (230Vac)
Height
80mm
ZDIN2 - Enclosure
Width
Depth
Loop Positive
Loop Negative
Screen
Height
Width
Depth
Loop Positive
Loop Negative
Screen
85mm
42mm
P+
P-
Screen
110mm
180mm
90mm
N/A
N/A
N/A
Designed to fit into ZDIN/ZDIN2.
35mm DIN rail = 145mm long
(2 number 85mm units will fit, cable
entry is top/bottom only).
Mains must be segregated from
unscreened loop cables within the
ZDIN. Care should be taken when
lives on different phases are switched
creating 415Vac within the ZDIN.
230Vac 5amp double change over
contacts.
For connections see page 15.
Z50D - Output contact
Height
78mm
Width
Depth
Loop Positive
Loop Negative
Screen
85mm
28mm
P+
P-
Screen
Loop Positive
Loop Negative
Screen
N/A
N/A
N/A
Designed to fit into ZDIN/ZDIN2.
1amp at 30VDC single change over
contact.
For connections see page 16.
ZDIN - Enclosure
Height
200mm
Width
Depth
255mm 100mm
35mm DIN rail = 244mm long.
56
Installation helpline 0844 412 1777
Book commissioning 01509 232651
57
3b
Sounders/visual
CLY200 - Sounder
CLY260 - Sounder base
Diameter
Depth
Alarm Positive
Alarm Negative
93mm
63mm
Common +
1st or 2nd tone
Screen
Diameter
Depth
Alarm Positive
Alarm Negative
Screen
*
112mm
30mm
+
1st or 2nd tone
*
* Terminate screens to 5amp connector
block or similar (not to building earth).
* Terminate screens to 5amp connector
block or similar (not to building earth).
Fixing centres 50-60mm apart.
Back entry only.
Fixing centres 50-60mm apart.
Back entry only.
Switch setting 00010 provides
1st tone sweeping with 2nd tone
continuous.
1st tone sweeping with 2nd tone
continuous.
CLY200D - IP65 sounder
CLY280 - High output sounder
Diameter
Depth
Alarm Positive
Alarm Negative
Screen
Height
Width
Depth
93mm
93mm
Common +
1st or 2nd tone
*
109mm
109mm
95mm
* Terminate screens to 5amp connector
block or similar (not to building earth).
Alarm Positive Alarm Negative
+ve
2nd
Screen
*
* Terminate screens to 5amp connector
block or similar (not to building earth).
Fixing centres 50-60mm apart.
Use designated gland entries (top
and bottom) when used externally
or IP rating is required.
Fixing centres 50-60mm apart.
Use internally, entries top and
back only.
Switch setting 00011000, 2nd tone
988Hz continuous.
Switch setting 00010 provides
1st tone sweeping with 2nd tone
continuous.
CLY407 - Xenon beacon and sounder
CLY230 - Bell
Diameter
Depth
Alarm Positive
Alarm Negative
Screen
150mm
80mm
+
-
*
* Terminate screens to 5amp connector
block or similar (not to building earth).
Fixing centres 50-60mm apart.
Use internally, entries top and
back only.
58
Installation helpline 0844 412 1777
Diameter
Depth
Alarm Positive
Alarm Negative
Screen
93mm
121mm
+
1st or 2nd tone
*
* Terminate screens to 5amp connector
block or similar (not to building earth).
Fixing centres 50-60mm apart.
Use designated gland entries (top
and bottom) when used externally
or IP rating is required.
1st tone sweeping with 2nd tone
continuous.
Book commissioning 01509 232651
59
3b
Sounders/visual
CLY400 - Xenon beacon
ZVOICE-S - Voice sounder
Diameter
Depth
Alarm Positive
Alarm Negative
93mm
106mm
+
-
Screen
Height
Width
Depth
Alarm Positive
*
160mm
95mm
70mm
Red
* Terminate screens to 5amp connector
block or similar (not to building earth).
Alarm Negative Screen
Black
*
* Terminate screens to 5amp connector
block or similar (not to building earth).
Fixing centres 50-60mm apart.
Unit designed to be fixed to conduit
box or simular with fixing centres
50-90mm apart
Use designated gland entries (top
and bottom) when used externally
or IP rating is required.
Back entry only.
CLY408 - LED beacon and sounder
ZVOICE-H - Voice sounder
Diameter
Depth
Alarm Positive
Alarm Negative
Screen
Height
93mm
78mm
Common +
1st or 2nd tone
*
165mm
* Terminate screens to 5amp connector
block or similar (not to building earth).
Width
Depth
Alarm Positive
180mm 250mm
Red
Alarm Negative Screen
Black
*
* Terminate screens to 5amp connector
block or similar (not to building earth).
Fixing centres 50-60mm apart.
Allows for one cable entry (gland
supplied) for remote connection
to local conduit box.
Switch setting 00010 1st tone
sweeping with 2nd tone continuous.
CLY408D - IP65 beacon and sounder
Diameter
Depth
Alarm Positive
Alarm Negative
Screen
93mm
108mm
Common +
1st or 2nd tone
*
* Terminate screens to 5amp connector
block or similar (not to building earth).
Fixing centres 50-60mm apart.
Use designated gland entries (top
and bottom) when used externally
or IP rating is required.
Switch setting 00010 provides
1st tone sweeping with 2nd tone
continuous.
60
Installation helpline 0844 412 1777
Book commissioning 01509 232651
61
3c
PSU’s
ZC/1/3 - Power supply unit
ZC/5/18 - Power supply unit
Height
Width
Depth
Height
Width
Depth
230mm
230mm
80mm
400mm
400mm
110mm
Ensure the cables do not enter near the
position for the batteries (bottom half).
There is generally enough space for
small interface equipment such as
Z45D, Z570, Z51D.
Ensure the cables do not enter near the
position for the batteries (bottom half).
There is generally enough space for
small interface equipment such as
Z45D, Z570, Z51D.
All PSU’s require un-switched fused
spurs connected to radials from the
main electrical distribution board.
All PSU’s require un-switched fused
spurs connected to radials from the
main electrical distribution board.
ZC/1/7 - Power supply unit
ZC/10/12 - Power supply unit
Height
Width
Depth
Height
Width
Depth
230mm
320mm
80mm
400mm
400mm
200mm
Ensure the cables do not enter near the
position for the batteries (bottom half).
There is generally enough space for
small interface equipment such as
Z45D, Z570, Z51D.
Ensure the cables do not enter near the
position for the batteries (bottom half).
There is generally enough space for
small interface equipment such as
Z45D, Z570, Z51D.
All PSU’s require un-switched fused
spurs connected to radials from the
main electrical distribution board.
All PSU’s require un-switched fused
spurs connected to radials from the
main electrical distribution board.
ZC/3/12 - Power supply unit
Height
Width
Depth
400mm
400mm
110mm
Ensure the cables do not enter near the
position for the batteries (bottom half).
There is generally enough space for
small interface equipment such as
Z45D, Z570, Z51D.
All PSU’s require un-switched fused
spurs connected to radials from the
main electrical distribution board.
62
Installation helpline 0844 412 1777
Book commissioning 01509 232651
63
3c
PSU’s
ZH/15/3 - Power supply unit
ZH/10/40 - Power supply unit
Height
Width
Depth
Height
Width
Depth
300mm
400mm
80mm
500mm
450mm
200mm
Ensure the cables do not enter near the
position for the batteries (bottom half).
There is generally enough space for
small interface equipment such as
Z45D, Z570, Z51D.
Ensure the cables do not enter near the
position for the batteries (bottom half).
There is generally enough space for
small interface equipment such as
Z45D, Z570, Z51D.
All PSU’s require un-switched fused
spurs connected to radials from the
main electrical distribution board.
All PSU’s require un-switched fused
spurs connected to radials from the
main electrical distribution board.
ZH/3/7 - Power supply unit
ZH/20 - Power supply unit
Height
Width
Depth
Height
Width
Depth
300mm
400mm
80mm
500mm
450mm
200mm
Ensure the cables do not enter near the
position for the batteries (bottom half).
There is generally enough space for
small interface equipment such as
Z45D, Z570, Z51D.
Batteries in separate box (ZH/68/E)
1 number 2 core 2.5mm cable required.
In addition to this 4 number 2 core
2.5mm cables are required between
PSU and panel.
All PSU’s require un-switched fused
spurs connected to radials from the
main electrical distribution board.
ZH/5/24 - Power supply unit
ZH/68/E - Battery enclosure
Height
Width
Depth
Height
Width
Depth
500mm
450mm
200mm
500mm
450mm
200mm
Ensure the cables do not enter near the
position for the batteries (bottom half).
There is generally enough space for
small interface equipment such as
Z45D, Z570, Z51D.
All PSU’s require un-switched fused
spurs connected to radials from the
main electrical distribution board.
64
Installation helpline 0844 412 1777
Book commissioning 01509 232651
65
3c
Transformer rectifiers
ZN/17 - Transformer rectifier (0.375A)
ZN/19 - Transformer relay
Height
Width
Depth
Height
Width
Depth
115mm
155mm
76mm
110mm
110mm
58mm
Surface mounting with cable top, side
or bottom, not back entry.
Surface mounting with cable top, side
or bottom, not back entry.
All transformer rectifiers require
un-switched fused spurs connected
to radials from the main electrical
distribution board.
All transformer rectifiers require
un-switched fused spurs connected
to radials from the main electrical
distribution board.
ZN/18 - Transformer rectifier (1.5A)
Height
Width
Depth
200mm
255mm
100mm
Surface mounting with cable top, side
or bottom, not back entry.
All transformer rectifiers require
un-switched fused spurs connected
to radials from the main electrical
distribution board.
ZN/16 - Transformer rectifier (3A)
Height
Width
Depth
200mm
255mm
100mm
Surface mounting with cable top, side
or bottom, not back entry.
All transformer rectifiers require
un-switched fused spurs connected
to radials from the main electrical
distribution board.
66
Installation helpline 0844 412 1777
Book commissioning 01509 232651
67
3d
Ancillary
ZREDCARE/BOX - Redcare enclosure
CLY410 - Door holder (24Vdc)
Height
Width
Depth
Height
Width
Depth
245mm
230mm
80mm
95mm
95mm
45mm
Surface mounted enclosure for 24Vdc
RedCare communicator.
24Vdc unit. Rear entry with conduit
box otherwise bottom or side entry
only and terminate +ve’s and -ve’s as
shown.
24Vdc supply from panel/PSU and
1 number 2 core cable for fire.
Rated holding force 112 newtons or
11.5Kg’s.
Any cable entry.
Schematic shown on page 6.
Schematic shown on page 14.
Z67 - IP heat detector
CLY420 - Door holder (230Vac)
Diameter
Depth
Zone Positive
Zone Negative
Screen
Height
Width
Depth
98mm
50mm
Red
Blue
*
95mm
95mm
45mm
* Terminate screens to 5amp connector
block or similar (not to building earth).
No base required.
230Vac unit. Rear entry with conduit
box otherwise bottom or side entry
only and terminate LEN shown.
Flying leads from the back of the
detector.
Rated holding force 112 newtons or
11.5Kg’s.
70mm fixing centres do not allow
fixing to conduit box. Applications
where a back box is needed a Red
Alert box should be used eg YCR/502.
Schematic shown on page 15.
For use with Z570 see page 17.
996 - Door holder (24Vac)
CLY485 - Remote LED
Height
Width
Depth
85mm
85mm
25mm
LED c/w legend on a single gang
switch plate. Terminate +’s to number
2 (middle) and -’s to number 3 (right).
68
Installation helpline 0844 412 1777
Height
Width
Depth
64mm
305mm
92mm
Dimensions relate to main body of the
unit only.
Swing free and 24Vdc magnetic hold
open for doors up to 950mm and
60Kg’s.
Fitted on pull side of the door near the
hinges and the external switched
24Vdc terminated to the red and
black connections.
Book commissioning 01509 232651
69
3d
Ancillary
CLY475B - 230Vac relay
Z841 - Class change unit
Height
Width
Depth
Height
Width
Depth
110mm
110mm
58mm
110mm
230mm
45mm
Surface mounted top, side or bottom
cable entry.
Surface mounted only.
The unit requires 230Vac and link to
Z740/Z45D or to the panel.
Relay has a 230Vac coil and double
pole change over contacts rated
230Vac 5amp (2.5amp for inductive
loads).
The box will not accept a 20mm gland,
cable entry possible top, bottom,
left or rear.
ZKEY2 - Keyswitch
Z2000 - Conventional beam detection
Height
Width
Depth
Port
Depth
82mm
80mm
55mm
Tx
110mm
RX
110mm
Controller
90mm
2 position surface key switch labelled
“plant isolate control” with “normal”
and “isolate” as selectable functions
using a normally open going closed
switch.
Height
Diameter
60mm
60mm
260mm
210mm
Additional information from the
installation helpline – 0844 412 1777.
Rated 230Vac 5amp but typically used
with Z745, Z740 or Z45D.
See diagram on page 22.
CLY495B - 24Vdc relay
CLY517 - Conventional IP MCP
Height
Width
Depth
Height
Width
Depth
110mm
110mm
58mm
124mm
124mm
80mm
Surface mounted top, side or bottom
cable entry.
Used typically in cold stores with
interface to addressable loop.
Relay has a 24Vdc coil and double pole
change over contacts rated 230Vac
5amp (2.5amp for inductive loads).
Surface mounting only with surface
cable installation.
70
Width
Installation helpline 0844 412 1777
Top and bottom 20mm glands used
to retain IP67.
Book commissioning 01509 232651
71
3d
Ancillary
Z440 - Rotating beacon
ZNLINK - Interface
Diameter
Depth
Height
Width
Depth
120mm
200mm
110mm
110mm
58mm
230Vac unit mounted in an up right
position for IP rating and effective use.
The unit is supplied with “o” ring and
gasket for IP rating.
Surface mounting unit that gives a
two way signal, over a 2 core cable,
between panels.
One Znlink per panel, maximum
10 panels.
For interfacing/ monitoring
requirements call the installation
helpline – 0844 412 1777.
Six core required between Znlink and
local panel.
Panel specification – Aux 24Vdc supply,
none latching zone/class change, spare
sounder cct.
UV/IR - Flame detection
Height
Width
Depth
142mm
108mm
82mm
All information can be provided by the
installation helpline – 0844 412 1777.
Z805 - Radio modem
Height
Width
Depth
185mm
114mm
30mm
All information can be provided by the
installation helpline – 0844 412 1777.
72
Installation helpline 0844 412 1777
Book commissioning 01509 232651
73
3d
I.S. equipment
Z710Ex-1 - Ionisation sensor
Z786Ex-1 - Manual call point
Diameter
Depth
Loop Positive
Loop Negative
Screen
Height
Width
Depth
Loop Positive
Loop Negative
Screen
106mm
52mm
N/A
N/A
N/A
120mm
120mm
75mm
Left
Middle
Right
See diagrams on page 24 for all
information.
See diagrams on page 24 for all
information.
Requires a surface base Z7SB-1.
Surface mounting only top,
bottom or side entry.
Z720Ex-1 - Heat sensor
ZP-LC - Line conditioner
Diameter
Depth
Loop Positive
Loop Negative
Screen
106mm
52mm
N/A
N/A
N/A
See diagrams on page 24 for all
information.
Height
75mm
Width
Depth
Loop Positive
Loop Negative
Screen
55mm
110mm
+
-
Screen
Loop Positive
Loop Negative
Screen
N/A
N/A
N/A
See diagrams on page 24 for all
information.
Requires a surface base Z7SB-1.
Z7SB-1 - Base
ZP-ZB - Zenner barrier
Diameter
Depth
Loop Positive
Loop Negative
Screen
108mm
18mm
5
8
7
See diagrams on page 24 for all
information.
74
Installation helpline 0844 412 1777
Height
Width
Depth
115mm 12.5mm 110mm
See diagrams on page 24 for all
information.
Book commissioning 01509 232651
75
3d
I.S. equipment
Z740Ex-1 - Interface
XB8024-S-NR - Beacon
Height
Width
Depth
Loop Positive
Loop Negative
Screen
Diameter
Depth
Alarm Positive
Alarm Negative
Screen
120mm
120mm
55mm
Left
Middle
Right
140mm
107mm
+
-
*
Loop Negative
Screen
See diagrams on page 24 for all
information.
* Terminate screens to 5amp connector
block or similar (not to building earth).
Surface mounting only top,
bottom or side entry.
See diagrams on page 24 for all
information.
MTL5025 - Galvanic isolator
DX070 - Enclosure
Height
Width
Depth
104mm
16mm
110mm
Loop Positive
Loop Negative
Screen
Height
Width
Depth
Loop Positive
175mm 125mm 150mm
See diagrams on page 24 for all
information.
See diagrams on page 24 for all
information.
DB5 - Sounder
Diameter
Depth
Alarm Positive
Alarm Negative
Screen
93mm
103mm
Common +
1st or 2nd tone
*
* Terminate screens to 5amp connector
block or similar (not to building earth).
See diagrams on page 24 for all
information.
Fixing centres 50-60mm apart.
Back entry only.
Switch setting 00010 1st tone
sweeping and 2nd tone continuous.
76
Installation helpline 0844 412 1777
Book commissioning 01509 232651
77
3d
Radio
ZR-471A - 1 way radio module
ZR-5500 - Whip aerial
Height
Width
Depth
Height
Width
Depth
260mm
360mm
70mm
900mm
25mm
150mm
See diagrams on page 26 for all
information.
See diagrams on page 26 for all
information.
Exact position determined
by site survey.
Exact position determined
by site survey.
ZR-472A - 2 way radio module
Height
Width
Depth
260mm
360mm
70mm
See diagrams on page 26 for all
information.
Exact position determined
by site survey.
78
Installation helpline 0844 412 1777
Book commissioning 01509 232651
79
3d
Radio
ZR430 - Optical sensor
ZR420-ES - Heat sensor/sounder
Diameter
Depth
Diameter
Depth
106mm
52mm*
150mm
85mm
* Depth of dimension excludes base.
See diagrams on page 26 for all
information.
See diagrams on page 26 for all
information.
Fixings centres 60-80mm apart.
Exact position determined
by site survey.
Exact position determined
by site survey.
ZR420 - Heat sensor
ZR401 - Sensor base
Diameter
Depth
Diameter
Depth
106mm
52mm*
115mm
40mm
* Depth of dimension excludes base.
See diagrams on page 26 for all
information.
See diagrams on page 26 for all
information.
Fixing centres 40, 50 or 60mm apart.
Exact position determined
by site survey.
Exact position determined
by site survey.
ZR430-ES - Optical sensor/sounder
ZR485 - Manual call point
Diameter
Depth
Height
Width
Depth
150mm
85mm
89mm
89mm
62mm
See diagrams on page 26 for all
information.
See diagram for further information
on page 26.
Fixings centres 60-80mm apart.
Surface only
Exact position determined
by site survey.
Remove the black centre disc in
the box.
Fixings 35/50mm apart.
Exact position determined
by site survey.
80
Installation helpline 0844 412 1777
Book commissioning 01509 232651
81
3d
Radio
ZR454 - Sounder
ZR454WP - IP sounder
Height
Width
Depth
Height
Width
Depth
85mm
85mm
95mm
85mm
85mm
95mm
See diagrams on page 26 for all
information.
See diagrams on page 26 for all
information.
Remove batteries to fix, note battery
polarities.
Remove batteries to fix, note battery
polarities.
Exact position determined
by site survey.
Exact position determined
by site survey.
ZR454XN - Sounder/beacon
ZR451 - I/O unit
Height
Width
Depth
180mm
85mm
95mm
See diagrams on page 26 for all
information.
Height
Width
Depth
250mm
160mm
40mm
See diagrams on page 26 for all
information.
Remove batteries to fix, note battery
polarities.
Bottom entry only.
Switch rated low voltage DC only.
Exact position determined
by site survey.
Input requires 2K2 EOL and short cct
for fire.
See base for fixings.
Exact position determined
by site survey.
ZR4-XN - Beacon
Height
Width
Depth
180mm
85mm
95mm
See diagrams on page 26 for all
information.
Remove batteries to fix, note battery
polarities.
Exact position determined
by site survey.
82
Installation helpline 0844 412 1777
Book commissioning 01509 232651
83
4
System commissioning
To ensure the system commissioning runs as smoothly as
possible we would request that the following points have
been observed prior to booking the commissioning visit.
1
7 working days notice for commissioning visit.
2
As-fitted drawings marked up with address numbers.
3
Text label sheets complete at the time of booking the
commissioning.
4
Any specific system configuration identified.
5
Loop complete and tested for continuity on both cores
and screen.
6
No cable faults exist (short cct between cores, cores to
screen or cores to building earth).
7
Cables terminated to the panel have each core correctly
flagged.
8
Access equipment and operator available for our use.
9
Zone charts require 3 weeks notice and a disk copy of
the AutoCad drawings.
10 All equipment is fitted that is directly connected to the
cable installation i.e. sounder 1st fix plates, sensor base,
MCP’s interfaces. All plug-in devices that require
addressing will be fitted by Clymac.
11 Free use of welfare facilities, light, power etc.
12 Clymac endeavour to work with personnel on site to
overcome most problems. Assistance may be required
to fix cable faults, fitting sensors etc, drive access
equipment and connect mains.
84
Installation helpline 0844 412 1777
Book commissioning 01509 232651
85
5
Contact details
Installation support helpline
0844 412 1777
Book commissioning
01509 232651
Office fax
01509 232665
Email
[email protected]
Web
www.clymac.co.uk
86
Installation helpline 0844 412 1777
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement