FTA-102L
Free Roaming Gateway
User Manual
FTA-102L
PORTech Communications Inc.
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
【Content】
1. Introduction ........................................................................................................... 1
2. System Topology .................................................................................................. 2
3. Function Description ............................................................................................ 2
4. Parts list ................................................................................................................. 3
5. Dimension: 14*9*3 cm .......................................................................................... 3
6. Chart of the device ................................................................................................ 4
6.1 Front Panel....................................................................................................... 4
6.2 Back Panel ....................................................................................................... 5
7. Web Page Setting .................................................................................................. 6
7.1 Via WAN port ................................................................................................... 6
7.2 Via LAN port ..................................................................................................... 6
8. System Information. ............................................................................................. 7
9. Phone Book ........................................................................................................... 8
10. SIM Setting .......................................................................................................... 9
10.1 Remote SIM Setting (FTA-102L) ..................................................................... 9
10.2 SIM Setting (MV-37X) ................................................................................... 10
11. Phone Setting .................................................................................................... 11
11.1 Master Setting ............................................................................................... 11
11.2 Volume Settings ............................................................................................ 12
11.3 DND Settings ................................................................................................. 12
11.4 Caller ID ........................................................................................................ 13
11.5 Dial Plan ........................................................................................................ 14
11.6 Flash Time..................................................................................................... 16
11.7 Alarm ............................................................................................................. 17
12. Network .............................................................................................................. 18
12.1 Network Status: You can check the current Network setting in this page. ..... 18
12.2 WAN .............................................................................................................. 19
12.3 LAN ............................................................................................................... 20
12.4 SNTP Settings ............................................................................................... 21
12.5 Virtual Server ................................................................................................. 22
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
13. SIP Settings ....................................................................................................... 23
13.1 Service Domain ............................................................................................. 23
13.2 Port Settings .................................................................................................. 24
13.3 Codec Settings .............................................................................................. 25
13.4 Codec ID ....................................................................................................... 26
13.5 DMTF Settings .............................................................................................. 26
13.6 Other Settings ............................................................................................... 27
14. NAT Trans. ......................................................................................................... 28
14.1 STUN Setting (optional) ................................................................................ 28
14.2 uPnP Setting ................................................................................................. 29
15. Others ................................................................................................................ 29
15.1 FXO&FXS...................................................................................................... 29
15.2 Advance ........................................................................................................ 30
15.3 Status Log ..................................................................................................... 30
16. Update ................................................................................................................ 31
16.1 New Firmware ............................................................................................... 31
16.2 Default Settings ............................................................................................. 32
17. Backup ............................................................................................................... 33
18. System Authority .............................................................................................. 33
19. Save Change ..................................................................................................... 34
20. Reboot ............................................................................................................... 34
21. Specification...................................................................................................... 35
21.1 Call transfer ................................................................................................... 35
21.2 Conference call ............................................................................................. 35
22.3 IVR Command ............................................................................................... 35
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
1. Introduction
When you go abroad with FTA-102L, all incoming calls of your original mobile phone are free of charge. FTA-102L provide free roaming fee for international inbound calls. When you are on business travel oversea, your coworkers, friends, family, and clients can just call your original mobile phone number to reach you.
This is of enormous benefit for user, you don’t’ need to use others country phone access number. Also, it’s simply and easy to send from your original mobile phone while traveling/abroad.
-1-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
2. System Topology
3. Function Description
1. Answer self-Mobile call at foreign country without any roaming fee (A-B-D-C or A-B-D-F).
2. Caller ID authentication for incoming call (F-D-B-G or
F-D-B-H).
3. Retrieve voice mail from foreign country ( C or F)
4. Dialing plan support for local FXO call.
5. C can transfer call to F, G or H.
6. A-C-F conference call.
-2-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
4. Parts list
Please check the parts for any missing parts. If do, please contact our agents：
4.1 「FTA-102L」main body
4.2 Power adaptor AC-DC (110V AC – 12V DC) or (220V AC – 12V
DC)
4.3 Network cable
4.4 Phone connecting Line
4.5 User Manual
(4.1)
(4.2)
(4.3)
(4.4)
5. Dimension: 14*9*3 cm
-3-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
6. Chart of the device
6.1 Front Panel
In normal situation, the register LED only blink at power-on stage for 3~6 times. If register LED keep blinking, the system is not in normal state and the registering of SIM may not be completed.
Once the register LED keep blinking for several minutes, check ether-net connection or try another STUN server which can be set in the WEB page.
FTA-102L
Fig-1.
*Power: LED on after power on.
*SIM status:
LED status
OFF
ON
Slow blinking
Flash off
Flash on
Fast blinking
Behavior
Default
SIM inserted but not registered registering
Registered but in maintain mode
Registered( standby mode )
Incoming or outgoing ringing
*Hook: Indicate the status of phone.
*PSTN: Indicate the status of PSTN line.
*Register:
LED status
OFF
ON blinking
Behavior
Default
Registered to SIP proxy
Checking NAT
-4-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
6.2 Back Panel
Fig-2.
*Restart button
Action
Short Click
Long Press (over 5 second)
Behavior
System restart
System factory reset and restart
-5-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
7. Web Page Setting
When the IP setting is done, the operator may setup all the rest parameters via web page.
Item Value
HTML Port
System User Name
System Password
Normal User Name
Normal Password
WAN port IP
LAN Port IP
9999 fta
1234 user
1234
Default DHCP
192.168.123.1
7.1 Via WAN port
Step1: Use the FXS port phone set to get the WAN IP by IVR (#126#).
Step2: Start a WEB browser window and enter the following line to access
WEB page. http://wan_ip:9999
7.2 Via LAN port
Step1: Start a WEB browser window and enter the following line to access
WEB page. http://192.168.123.1:9999
Fig-3.
-6-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
8. System Information.
8.1 When you login the web page, you can see the demo system current system information like firmware version, company… etc in this page.
8.2 Also you can see the function lists in the left side. You can use mouse to click the function you want to set up.
-7-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
9. Phone Book
You could add/delete items in current phone books.
-8-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
10. SIM Setting
10.1 Remote SIM Setting (FTA-102L)
For SIM card registering setting, both FTA and MV should be configured.
*Service Port: the UDP port of FTA used to connect with MV. Default value is 38000.
*SIM ID: User defined SIM ID. The peer GSM module of MV will use this SIM
ID as identity ID to connect with FTA.
*Module Name or URL: The SIP account of peer MV port.
-9-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
10.2 SIM Setting (MV-37X)
*Mode: When the SIM is inserted to SIM holder in MV, user should select
“Local” mode. If the SIM card is inserted in FTA, user should select Remote.
*Mobile ID: User defined ID which is used to identify the GSM module.
*Card ID: When the SIM card is inserted in FTA, user should configure MV to connect with FTA. This field is used to fill in the SIM ID which is set in the
FTA.
*SIM Server: The format of the field is “server_ip:port”,
When MV is used with FTA, this field is updated by the information send from
FTA. User only has to fill in a dummy server setting for “server_ip”, and it’s mandatory; “port” must corresponding to FTA’s Service Port.
Then Server will search and send back to FTA’s IP, user has to fill that new IP as “server_ip”
-10-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
11. Phone Setting
11.1 Master Setting
*Master Number: The number that FXO dial out (i.e. the phone number of F in the system topology). System uses this number to authenticate the caller ID of PSTN incoming call. If the caller ID matches to the setting in the master number, it has the permission to dial out via GSM in MV (i.e. F-D-B-G or
F-D-B-H).If the matching result is failed, the PSTN incoming call will ring the local FXS directly (F-D-C).
*No Answer Fwd Time Out: Setup the FXS ringing period. For VOIP call from MV, system always rings local FXS first. After ringing period, system change to dial master number via FXO port. (Parameter “0”: forwarding to
PSTN directly.)
-11-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
11.2 Volume Settings
You could set the volume of your phone in this page.
11.3 DND Settings
You could set the do not disturb period of your phone in this page
-12-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
11.4 Caller ID
In order to correctly generate caller ID, user should set the caller ID format of FXS. You could enable/disable the caller ID setting in this page.
-13-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
11.5 Dial Plan
*Routing to: Define the call direction (IP call or PSTN call) if the dialed digit match the rule set in Routing rule field.
*Routing rule: Define the digit string of routing rule. Only digit 0~9 are valid in rule string, as well as “x” denotes wildcard digit. Different patterns is separated by sign “+”.
*Drop prefix:
Item Description
Yes The following replace rule define the prefix dropping rule
No The following replace rule define the prefix adding rule
-14-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
*Replace Rule: The digit string defined in the first field will be added if the dialed string match the digit string defined in the second field of the replacement rule. If the selection of Drop prefix is “yes”, the matched digit string in the dialed string will be removed before adding prefix. Otherwise, if
“No” is selected, the prefix is added at the beginning of dialed string without removing any digits.
Only digit 0~9 are valid in rule string, as well as “x” denotes wildcard digit and
“,” denotes pause for one second. Different patterns is separated by sign “+”.
Example 1:
For example, the dialed string is 86621742885. After the processing of replacement rule, the result dialing string will become 002+86621742885.
Example 2:
For instance, the dialed string is 00286621742885. After the processing of replacement rule, the result dialing string will become 006 86621742885 since “Yes” of Drop prefix is select and “002” is dropped and replaced by
“006”.
Example 3:
In this example, any 4-digits string begin with 5, 35 or 21 will be add a “007” prefix. e.g. 5171 will become 0075171.
-15-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
Example 4:
In this example, any string begin with 5 will be add a “9” prefix. After the prefix “9” digit, it will be hold in 3 seconds and then the succeeded digits.
*Realm Selection: The default call behavior of FTA act as a SIM extender.
The default IP call will direct to peer MV, thus call by GSM network. User can specify ITSP by adding Realm Prefix before dialing destination number. The configuration of Realm Prefix can be found in the Dial Plan page.
11.6 Flash Time
You could set the flash time in this page
-16-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
11.7 Alarm
You could set the alarm time in this page.
-17-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
12. Network
In Network you can check the Network Status, WAN, LAN, STNP
Settings, and Virtual Server.
12.1 Network Status: You can check the current Network setting in this page.
-18-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
12.2 WAN
(1) The DHCP Client Configuration item is to setup the WAN port’s network environment.
(2) The PPPoE Configuration item is to setup the PPPoE
Username and Password. If you have the PPPoE account from your Service Provider, please input the Username and the
Password correctly.
(3) When you finished the setting, please click the Submit button.
-19-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
12.3 LAN
You could configure the LAN settings in this page.
-20-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
12.4 SNTP Settings
SNTP Setting function: you can setup the primary and second
SNTP Server IP Address, to get the date/time information. Also you can base on your location to set the Time Zone, and how long need to synchronize again. When you finished the setting, please click the Submit button.
-21-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
12.5 Virtual Server
You could set your virtual servers in this page. The usual port numbers are WEB [TCP 80], FTP(Control) [TCP 21], FTP(Data)
[TCP 20], E-mail(POP3) [TCP 110], E-mail(SMTP) [TCP 25], DNS
[UDP 53] and Telent [TCP 23].
-22-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
13. SIP Settings
In SIP Setting you can setup the Service Domain, Port Settings,
Codec Settings, Codec ID, DTMF Setting and Other Settings.
13.1 Service Domain
User need to set the registering information of SIP proxy at this page. FTA cannot work correctly without registering to SIP proxy.
First you need to click Active to enable the Service Domain, and then you can input the following items.
(1) Display name: you can input the name you want to display.
(2) User name: you need to input the User Name get from your ISP.
(3) Register Name: you need to input the Register Name get from your ISP.
(4) Register Password: you need to input the Register Password get from ISP.
(5) Domain Server: you need to input the Domain Server get from your ISP.
-23-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
(6) Proxy Server: you need to input the Proxy Server get from your
ISP. Please note, FTA-102L must connect "message Server".
E.g. the free server we recommend, IPTel, with this feature.
(7) Outbound Proxy: you need to input the Outbound Proxy get from your ISP. If your ISP does not provide the information, then you can skip this item.
(8) You can see the Register Status in the Status item.
(9) When you finished the setting, please click the Submit button.
Remember to click “Save Charge”
13.2 Port Settings
You could set the port number in this page.
-24-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
13.3 Codec Settings
You can setup the Codec priority, RTP packet length in this page.
You need to follow the ISP suggestion to setup these items. When you finished the setting, please click the Submit button.
-25-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
13.4 Codec ID
You can setup the Codec ID in this page.
13.5 DMTF Settings
You can setup the DTMF Setting in this page.
-26-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
13.6 Other Settings
Other Settings: you can setup the Hold by RFC and QoS in this page. To change these settings, please follow your ISP information.
When you finished the setting, please click the Submit button. The
QoS setting is to set the voice packets’ priority. If you set the value higher than 0, then the voice packets will get the higher priority to the Internet. But the QoS function still need to cooperate with the others Internet devices.
-27-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
14. NAT Trans.
In NAT Trans. you can setup STUN and uPnP function. These functions can help your VoIP device working properly behind NAT.
14.1 STUN Setting (optional)
There is a default setting of STUN server in the FTA system database; user can ignore this step, which is optional setting. If the STUN server is not connectable or service shutdown, please change STUN setting at this page.
-28-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
14.2 uPnP Setting
You could enable/disable the uPnP in this page.
15. Others
15.1 FXO&FXS
User should set FXS and FXO type according to country which FTA located.
-29-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
15.2 Advance
You could change advanced setting in this page.
15.3 Status Log
-30-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
16. Update
In Update you can update the system’s firmware to the new one or the factory reset to let the system back to default setting.
16.1 New Firmware
(1) In New Firmware function you can update new firmware via
Local PC in this page. You can upgrade the firmware by the following steps:
(2)Select the firmware code type.
(3)Click the “Browse” button in the right side of the File Location or you can type the correct path and the filename in File Location blank.
(4)Select the correct file you want to download to the system then click the Update button.
(5) Please click update/default setting after update firmware
-31-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
16.2 Default Settings
In this page: Update/ Default Settings, you could restore the factory default settings to the system. All setting will restore default setting.
IP will retain original IP as usual not default IP.
-32-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
17. Backup
You could save current system setting to file: System Settings and
PhoneBook.
18. System Authority
In System Authority you can change your login name and password
-33-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
19. Save Change
In Save Change you can save the changes you have done. If you want to use new setting in the VoIP system, you have to click the
Save button. After you click the Save button, the system will automatically restart and the new setting will effect.
20. Reboot
Reboot function you can restart the system. If you want to restart the system, you can just click the Reboot button, and then the system will automatically.
-34-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
21. Specification
21.1 Call transfer
During ongoing call, user can transfer current call by “flash hook”. The call will be transfer to PSTN if the current call is from VOIP, and vice versa.
21.2 Conference call
During ongoing call, user can initiate a conference call by “flash hook”+
“#512#”.
Function
Function
Function
Info
Info
Info
Info
Info
Info
22.3 IVR Command
Group
Function
Function
Function
Function
Function
Function
Action
IVR unlock
IVR lock
Reboot
Factory
Set DHCP client
Set static IP
Set network mask
Set default gateway IP
Set primary DNS
Check LAN IP Address
Check DHCP client status
User name of SIP account
Check network mask
Check default gateway IP
Check DNS key
#190#
#191#
#195#
#198#
#111#
#112xxx*xxx*xxx* xxx#
#113xxx*xxx*xxx* xxx# network mask default gateway IP
#114xxx*xxx*xxx* xxx# parameter(s)
Static IP address primary DNS
#115xxx*xxx*xxx* xxx#
#120#
#121#
#122#
#123#
#124#
#125#
-35-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
Info
Info
Info
Info
Function
Function
Function
Function
Check WAN IP Address
Software version
#126#
#128#
Check PSTN number of forward all call
#147#
Check PSTN number of no #149# answer forward call
Forward disable
Forward all call to PSTN
#145#
#147xxxxxxxx# PSTN number
No answer forward to PSTN #149xxxxxxxx# PSTN number conference #512#
-36-
-
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
