advertisement
User Manual
5-In-1 Multi-Function Environment Meter
Please read this user manual thoroughly before using this unit and keep it for your future reference.
Contents
1. Safety .................................................................. 3
2. Introduction .......................................................... 4
3. Specifications ...................................................... 5
4. Meter Description ................................................ 7
5. LCD Display Description ..................................... 9
6. Operating Instructions ....................................... 10
7. Operating Procedures ....................................... 11
8. Calibration ......................................................... 11
9. Notes ................................................................. 14
10. Accessories ..................................................... 14
1. Safety
Read the following safety information carefully before attempting to operate or service the meter.
Use the meter only as specified in this manual; otherwise, the warranty may be invalidated.
Environment conditions:
Altitude less than 2000 meters
RH ≤90%(Non-Condensation)
Operating Temperature: -30
℃ ~ 60℃
Maintenance
Repairs or servicing should only be performed by ATP
Instrumentation Ltd.
Wipe the unit with a dry soft cloth. Do not use abrasives or solvents on this instrument.
Safety Symbol
Complies with EMC
2. Introduction
The 5-In-1 Multi-Function Environment Meter is designed to combine the functions of a Sound Level Meter, Light Meter,
Anemometer, Humidity Meter and Temperature Meter into one unit. It is ideal for various practical applications in professional and home use, such as monitoring and collecting data of outdoor environments (temperature, humidity, sunlight, wind speed etc.), or testing noise and light levels for health and safety adherence in factories, schools, offices, airports etc.
3. Specifications
Applied standard
Accuracy
Display
Resolution
Frequency response
Measurement range
Frequency weighting
Microphone
Measuring range
Spectral response
Spectral accuracy
Cosine response
Accuracy
Photo detector
Air velocity range
Air velocity accuracy
Sound
IEC61672-1 CLASS2
±2.0dB
4 digit 55mm LCD screen
0.1dB
31.5Hz to 8,000Hz
Auto:35dB to 130dB dBA
1/2 inch Electric condenser microphone
Light
0 Lux to 200,000 Lux, 0 Fc to 20,000 Fc
CIE photopic ( CIE human eye response curve)
CIE Vλ function f1’
≦6% f2’ ≦2%
±4% rdg, ±0.5%f.s. (<10,000Lux)
±5% rdg, ±10 digits (>10,000Lux)
One silicon photo diode with filter
Airflow
0.5m/s to 30.0m/s
±3%, ±0.3d
Measurement units
Measurement range
Accuracy
Measurement units
Resolution
Measurement range
Accuracy
Resolution
Data update
Maximum value m/s, km/h, ft/min, knots, MPH,
Temperature
-40° to 70
℃(-40° to 158℉)
±2.0
℃, ±3.6℉
℃/℉
0.1
Humidity
10 to 95%RH
±5%RH
0.1
1 time per second
MAX
Minimum value
Data Hold
Auto power off
Power supply
MIN
HOLD
Automatic power off after approx. 15 minutes of inactivity
1x 9V battery with type of 006P,
NEDA1604 or IEC6F22
Battery life
Operating conditions
Storage conditions
Roughly 30 hours
-20
℃~60℃, 10%RH~90%RH
-40
℃~60℃, 10%RH~75%RH
Dimensions (L x W x H) 252 x 66 x 33mm
Weight 568g
4. Meter Description
1)
Wind muffler microphone cover
2)
Microphone
3)
LCD display
4)
Temp./Humidity selection key
5)
Backlight ON/OFF key
6)
HOLD key
7)
Units selection key
8)
Power ON/OFF key
9)
Function selection key
10)
MAX/MIN
11)
°C/°F Selection Key
12)
Potentiometer calibration for sound level
13)
Anemometer vane and Lux probe input
14)
Temperature and Humidity sensor input
15)
External DC 9V power supply terminal (positive inside and negative outside; Pore size:OD 3.5mm, ID 1.35mm)
16)
Tripod bush
17)
Battery Compartment
18)
Battery Compartment screw
5. LCD Display Description
1)
Temperature/Humidity reading display
2)
Battery indication
3)
Temperature unit icon
4)
Humidity unit icon
5)
Air velocity unit icon
6)
Sound level, Air velocity or Light reading display
7)
Sound level unit icon
8)
Light unit icon
9)
MAX/MIN
10)
Data Hold
11)
Power off timer
6. Operating Instructions
(1) Open battery cover and install a 9-volt battery in the battery compartment.
(2) Replace the battery cover and tighten the screw.
(3) Power the meter on.
(4) Press "MODE" key to select the desired function.
Notes:
When the low battery icon "
" appears, replace the meters battery.
Hold the meter in hand or use the tripod to affix the meter in the desired location. The best measuring distance is 1 to
1.5m away from the sound source to the microphone.
To use the AC adapter, insert the plug of the adapter
(3.5φ)into the DC 9V connector on the side panel.
7. Operating Procedures
7.1 Temperature/Humidity reading selection
After powering the meter on, press the "
Temperature or Humidity reading.
7.2 Backlight ON/OFF;
" key to select
After powering the meter on, press the " " key once and the backlight will turn on. Press this key again to turn it off.
The backlight will automatically turn off after approximately
30 seconds of inactivity
7.3 Data Hold
Press the " " button once, "HOLD" icon will appear on the
LCD which indicates the data is frozen. To exit from data hold mode, press the button again.
7.4 Units selection
7.4.1 Measuring Air Velocity
(1) After entering Air Velocity mode, press the “ ” button to select the desired units. The device will cycle through m/s, km/h, ft/min, knots and MPH in turn.
7.4.2 Measuring Light
(2) After entering Light mode, press the “ ” button to select Lux or Fc.
7.5 Power ON/OFF
Turn the meter on by pressing the " " button for 1 second, and to turn the meter off, press and hold the " " button for at least 3 seconds
7.6 MODE button
After turning the meter on, press the “ ” button to select desired the function. The device will cycle though Sound
Level, Air Velocity and Light in turn.
7.7 MAX/MIN record
Whilst in measuring mode, press the " " key to enter
MAX/MIN measurement. ‘MAX’ will appear on the LCD and the maximum recorded value will be displayed. Press the key again; ‘MIN’ will appear on the LCD and the minimum recorded value will be displayed. Press the key again to exit
MAX/MIN measurement mode.
7.8 Temperature units selection
When in measuring mode, press the “ ” button to select between
℃ or ℉.
8. Calibration
The recommended recalibration period is 1 year.
Calibration, repairs or servicing should only be performed by
ATP Instrumentation Ltd.
NOTE: All products are calibrated before delivery.
9. Notes
(1) Do not store or operate the meter in high temperature or humidity.
(2) Remove the battery when the meter is to be stored for long periods of time to avoid battery leakage.
(3) Wind blowing across the microphone will affect the noise measurement. Use the supplied wind muffler to cover the microphone during applications involving turbulent air.
(4) Keep microphone dry and avoid severe vibration.
10. Accessories
① User manual
② Temperature and Humidity probe
③ Anemometer vane
④ Lux probe
⑤ Wind muffler
⑥ 9V battery
⑦ Adaptor (Optional)
⑧ Tripod (Optional)
ATP Instrumentation Ltd
Tournament Way
Ashby-de-la-Zouch
Leicestershire
LE65 2UU
Sales: 01530 566800. [email protected]
Repair and Calibration: 01530 566804. [email protected] www.atp-instrumentation.co.uk
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project