HealthRider HETL13913 150T User manual

HealthRider HETL13913 150T User manual
Model No. HETL13913.0
Serial No.
Write the serial number in the space
above for reference.
USER’S MANUAL
Serial Number
Decal
CUSTOMER SERVICE
UNITED KINGDOM
Call: 08457 089 009
From Ireland: 053 92 36102
Website: www.iconsupport.eu
E-mail: [email protected]
Write:
ICON Health & Fitness, Ltd.
c/o HI Group PLC
Express Way
CASTLEFORD
WF10 5QJ
UNITED KINGDOM
AUSTRALIA
Call: 1800 993 770
E-mail: [email protected]
Write:
ICON Health & Fitness
PO Box 635
WINSTON HILLS NSW 2153
AUSTRALIA
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
www.iconeurope.com
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
THE CHEST HEART RATE MONITOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
OPERATION AND ADJUSTMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
EXERCISE GUIDELINES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
RECYCLING INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARNING DECAL PLACEMENT
This drawing shows the locations of the warning
decals. If a decal is missing or illegible, call
the telephone number on the front cover of
this manual and request a free replacement
decal. Apply the decal in the location shown.
Note: The decals may not be shown at actual
size.
305284
HEALTHRIDER is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read
all important precautions and instructions in this manual and all warnings on your treadmill before
using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12.When connecting the power cord (see page
17), plug the power cord into an earthed
circuit. No other appliance should be on the
same circuit. When replacing the fuse in the
power cord adapter, insert an ASTA-approved
BS1362, 13-amp fuse into the fuse carrier.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons
with pre-existing health problems.
13.If an extension cord is needed, use only a
3-conductor, 14-gauge (1 mm2) cord that is
no longer than 5 ft. (1.5 m).
3. Use the treadmill only as described in this
manual.
14.Keep the power cord away from heated
surfaces.
4. The treadmill is intended for home use only.
Do not use the treadmill in any commercial,
rental, or institutional setting.
15.Never move the walking belt while the power
is turned off. Do not operate the treadmill
if the power cord or plug is damaged, or if
the treadmill is not working properly. (See
TROUBLESHOOTING on page 26 if the treadmill is not working properly.)
5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Place the treadmill on a level surface, with
at least 8 ft. (2.4 m) of clearance behind it
and 2 ft. (0.6 m) on each side. Do not place
the treadmill on any surface that blocks air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
16.Read, understand, and test the emergency
stop procedure before using the treadmill
(see HOW TO TURN ON THE POWER on
page 19).
17.Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
7. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
18.The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
8. Keep children under age 12 and pets away
from the treadmill at all times.
9. The treadmill should be used only by persons weighing 330 lbs. (150 kg) or less.
19.The heart rate monitor is not a medical
device. Various factors, including the user’s
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
10.Never allow more than one person on the
treadmill at a time.
11.Wear appropriate exercise clothes while
using the treadmill. Do not wear loose
clothes that could become caught in the
treadmill. Athletic support clothes are recommended for both men and women. Always
wear athletic shoes. Never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
20.Never leave the treadmill unattended while
it is running. Always remove the key, press
the power switch into the off position (see
the drawing on page 5 for the location of the
power switch), and unplug the power cord
when the treadmill is not in use.
3
21.Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 7, and HOW TO FOLD
AND MOVE THE TREADMILL on page 25.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
25.
22.When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
23.Never insert any object into any opening on
the treadmill.
DANGER:
Always unplug the power
cord immediately after use, before cleaning the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service representative only.
26.Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
24.Inspect and properly tighten all parts of the
treadmill regularly.
SAVE THESE INSTRUCTIONS
4
BEFORE YOU BEGIN
Thank you for selecting the new HEALTHRIDER®
H150T treadmill. The H150T treadmill provides an
impressive selection of features designed to make your
workouts at home more effective and enjoyable.
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after
reading this manual, please see the front cover of this
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Length: 6 ft. 8 in. (203 cm)
Width: 3 ft. 2 in. (97 cm)
Weight: 225 lbs. (102 kg)
Console
Accessory Tray
Handrail
Heart Rate Monitor
Key/Clip
Motor Hood
Walking Belt
Power Switch
Foot Rail
Wheel
Platform Cushion
Idler Roller
Adjustment Screws
5
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used for assembly. The number in parentheses below each drawing is the key number of the part, from the Part List near the end of this manual. The number following the key
number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached. Extra parts may be included.
#10 Star
Washer (5)–4
#8 x 1/2" Silver
Screw (6)–1
5/16" Star
Washer (8)–4
#8 x 1/2"
Screw (1)–14
3/8" Star
Washer (10)–8
#8 x 3/4" Tek
Screw (13)–8
5/16" x 2 3/4" Screw (12)–4
#8 x 3/4"
Screw (14)–4
3/8" x 1 1/4"
Screw (3)–4
3/8" x 2" Bolt (2)–2
3/8" x 2 3/4" Screw (22)–4
5/16" Flat
Washer (XX)–4
3/8" x 3 1/2" Screw (9)–4
3/8" Nut (9)–2
3/8" x 4" Screw (3)–6
6
#10 x 3/4"
Screw (4)–4
ASSEMBLY
• Assembly requires two persons.
• To identify small parts, see page 6.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you finish all assembly steps.
• Assembly requires the following tools:
the included hex keys
one adjustable wrench
• After shipping, there may be an oily substance
on the exterior of the treadmill. This is normal. If
there is an oily substance on the treadmill, wipe
it off with a soft cloth and a mild, non-abrasive
cleaner.
one Phillips screwdriver
scissors
needlenose pliers
• Left parts are marked “L” or “Left and right parts
are marked “R” or “Right.”
To avoid damaging parts, do not use power tools.
1.
Go to www.iconsupport.eu on your computer
and register your product.
• activates your warranty
• allows us to notify you of upgrades and offers
1
• saves you time if you ever need to contact
Customer Service
Note: If you do not have Internet access, call
Customer Service (see the front cover of this
manual) and register your product.
7
2.
Make sure that the power cord is unplugged.
2
With the help of a second person, tip the treadmill onto its right side.
29
Hole 6
91
A
Pull the Upright Wire (91) and the base ground
wire (A) through the indicated hole in the
Base (29).
90
Attach the base ground wire (A) to the Base (29)
with a #8 x 1/2" Silver Screw (6).
Make sure that the Grommet (90) is pressed into
the square hole in the Base (29).
See the inset drawing. Cut the plastic tie near
the Upright Wire (91). Be careful not to damage the Upright Wire.
Tie
Cut
91
3.Attach the Left Wheel Cap (110) to the Base (29)
with two #8 x 3/4" Screws (14).
3
Next, attach four Base Pads (37) to the Base
(29) with eight #8 x 3/4" Tek Screws (13) (only
two Base Pads are shown). Do not overtighten
the Screws.
37
14
13
With the help of a second person, tip the treadmill so that the Base (29) is flat on the floor.
29
Attach the Right Wheel Cap (not shown) as
described above.
8
13
37
110
4.Identify the Left Upright (84). Have a second
person hold the Left Upright near the Base (29).
4
See the inset drawing. Tie the wire tie in the
Left Upright (84) securely around the end of the
Upright Wire (91). Then, pull the other end of the
wire tie until the Upright Wire is routed through
the Left Upright.
91
84
Wire
Tie
Wire
Tie
84
91
5.Hold the Left Upright (84) against the Base (29).
Be careful not to pinch the wires. If necessary, position the base ground wire (A) in the
hole in the side of the Left Upright. Insert two
3/8" x 2 3/4" Screws (22) with two 3/8" Star
Washers (10) and two 3/8" x 1 1/4" Screws (3)
with two 3/8" Star Washers (10) into the Left
Upright.
5
Partially tighten the 3/8" x 2 3/4" Screws (22)
and the 3/8" x 1 1/4" Screws (3) until the heads
of the Screws touch the Left Upright (84); do not
fully tighten the Screws yet. Note: It may be
helpful to use the short hex key (B) on the Screw
shown.
84
22
Attach the Right Upright (not shown) in the
same way. Note: There are no wires on the right
side.
10
3
9
B
10
A
10
29
29
91
6.Identify the Left and Right Base Covers (88, 89).
6
Slide the Left Base Cover (88) onto the Left
Upright (84). Slide the Right Base Cover (89)
onto the Right Upright (85). Do not press the
Base Covers into place yet.
85
89
84
88
7.Identify the left Handrail (79). If there is a wire in
the left Handrail, remove and discard it.
7
12
Hold the left Handrail (79) near the Left Upright
(84). Insert the wire tie on the Upright Wire (91)
into the bottom of the left Handrail and out of
the end as shown. Then, pull the Upright Wire
through the Left Handrail.
91
79
8
C
Wire
Tie
Attach the left Handrail (79) to the Left Upright
(84) with two 5/16" x 2 3/4" Screws (12) and two
5/16" Star Washers (8). Make sure not to pinch
the Upright Wire (91). Do not tighten the
Screws yet.
Remove the two indicated screws (C) from the
left Handrail (79) and discard them.
84
10
8.Attach the right Handrail (79) to the Right
Upright (85) with two 5/16" x 2 3/4" Screws (12)
and two 5/16" Star Washers (8). Do not tighten
the Screws yet.
8
12
Remove the two indicated screws (C) from the
right Handrail (79) and discard them.
8
C
79
85
9.Set the Console Base (98) face down on a soft
surface to avoid scratching the Console Base.
94
11
Remove the two screws (D) and the two ties
from the Pulse Crossbar (81). Then, remove the
Pulse Crossbar and discard the screws.
101
98
Remove the four 5/16" x 5/8" Screws (11) from
the Console Frame (101). The Screws will be
used in a later step.
D
11
Tie
81
Tie
11
10.Identify the Left and Right Trays (95, 96).
10
Attach the Left and Right Trays (95, 96) to the
Console Base (98) with eight #8 x 1/2" Screws
(1). Tip: It may be easier to start the two
inside Screws and then slide the Trays into
place before tightening the other six Screws.
1
101
96
1
95
Note: It may be necessary to rotate the Console
Frame (101) upward when attaching the Left and
Right Trays (95, 96).
1
98
1
1
11.IMPORTANT: To avoid damaging the Pulse
Crossbar (81), do not use power tools and do
not overtighten the #10 x 3/4" Screws (4).
11
4
79
Orient the Pulse Crossbar (81) as shown. Attach
the Pulse Crossbar to the Handrails (79) with
four #10 x 3/4" Screws (4) and four #10 Star
Washers (5). Start all four Screws, and then
tighten them.
81
Make sure that the Upright Wire (91) is not
pinched. Firmly tighten the four 5/16" x 2 3/4"
Screws (12).
12
4
91
5
79
12
12
5
12.With the help of a second person, hold the console assembly near the Handrails (79) (only one
Handrail is shown).
12
Console
Assembly
Connect the ground wire from the console
assembly to the Ground Wire (80) on the Pulse
Crossbar (81).
Connect the Upright Wire (91) to the console
wire. See the inset drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and try
again. If YOU DO NOT CONNECT the connectors properly, the console may
become damaged when you turn on
the power. Then, remove the wire tie from
the Upright Wire.
Ground
Wire
91
80
Console
Wire
13.Set the console assembly on the Handrails (79).
Make sure that no wires are pinched. Insert
the excess Upright Wire (91) behind the Console
Frame (101).
Console
Wire
91
13
79
81
Wire
Tie
Console
Assembly
101
Attach the console assembly to the brackets
on the Handrails (79) with the four 5/16" x 5/8"
Screws (11) that you removed in step 9. Do not
tighten the Screws yet.
91
79
11
13
79
11
14.Attach the Pulse Crossbar (81) to the console
assembly with six #8 x 1/2" Screws (1). Start all
six Screws, and then tighten them.
14
Console
Assembly
Firmly tighten the four 5/16" x 5/8" Screws (11).
11
11
81
1
15.Firmly tighten the four 3/8" x 2 3/4" Screws (22),
and then tighten the four 3/8" x 1 1/4" Screws (3)
(only one side is shown).
1
15
Press the Left Base Cover (88) and the Right
Base Cover (not shown) onto the Base (29) until
they snap into place.
88
22
3
3
29
14
1
16.Raise the Frame (57) to the position shown.
Have a second person hold the Frame until
step 17 is completed.
16
57
Orient the Storage Latch (54) so that the large
barrel and the latch knob are oriented as shown.
Remove any ties from the end of the Storage
Latch (54). Attach the lower end of the Storage
Latch to the Base (29) with a 3/8" x 2" Bolt (2)
and a 3/8" Nut (9).
29
Latch
Knob
17.Attach the upper end of the Storage Latch (54) to
the Frame (57) with a 3/8" x 2" Bolt (2) and a 3/8"
Nut (9).
9
2
54
Large
Barrel
17
57
Lower the Frame (57) (see HOW TO LOWER
THE TREADMILL FOR USE on page 25).
9
2
54
18.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plastic
on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill.
Note: Extra parts may be included. Keep the included hex key in a secure place; the hex key is used to adjust
the walking belt (see pages 27 and 28).
15
THE CHEST HEART RATE MONITOR
HOW TO PUT ON THE HEART RATE MONITOR
The heart rate
monitor consists of
a chest strap and a
sensor. Insert the
tab on one end of
the chest strap into
the hole in one end
of the sensor as
shown. Then, press
the end of the sensor under the buckle
on the chest strap.
The tab should be
flush with the front of
the sensor.
Tabs
• D
o not expose the heart rate monitor to direct sunlight for extended periods of time; do not expose it to
temperatures above 122° F (50° C) or below 14° F
(-10° C).
Chest
Strap
• D
o not excessively bend or stretch the sensor when
using or storing the heart rate monitor.
Sensor
• T
o clean the sensor, use a damp cloth and a small
amount of mild soap. Then, wipe the sensor with a
damp cloth and thoroughly dry it with a soft towel.
Never use alcohol, abrasives, or chemicals to clean
the sensor. Hand wash and air dry the chest strap.
TROUBLESHOOTING
Tab
If the heart rate monitor does not function properly, try
the steps below.
Sensor Buckle
The heart rate monitor must be worn
under your clothes,
tight against your
skin. Wrap the heart
rate monitor around
your chest in the
location shown.
Make sure that
the logo is rightside-up. Then, attach the other end of the chest strap
to the sensor. Adjust the length of the chest strap, if
necessary.
• M
ake sure that you are wearing the heart rate monitor as described at the left. If the heart rate monitor
does not function when positioned as described,
move it slightly lower or higher on your chest.
• If heart rate readings are not displayed until you
begin perspiring, rewet the electrode areas.
• F
or the console to display heart rate readings, you
must be within arm’s length of the console.
• If there is a battery cover on the back of the sensor,
replace the battery with a new battery of the same
type.
Pull the sensor away from your body a few inches and
locate the two electrode areas, which are covered by
shallow ridges. Using saline solution such as saliva or
contact lens solution, wet the electrode areas. Then,
return the sensor to a position against your chest.
• T
he heart rate monitor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical conditions such as premature ventricular contractions
(pvcs), tachycardia bursts, and arrhythmia.
CARE AND MAINTENANCE
• T
horoughly dry the sensor with a soft towel after
each use. Moisture may keep the sensor activated,
shortening the life of the battery.
• S
tore the heart rate monitor in a warm, dry place. Do
not store the heart rate monitor in a plastic bag or
other container that may trap moisture.
16
• T
he operation of the heart rate monitor can be
affected by magnetic interference from high power
lines or other sources. If you suspect that magnetic
interference is causing a problem, try relocating the
fitness equipment.
SP
OPERATION AND ADJUSTMENT
HOW TO PLUG IN THE POWER CORD
Follow the steps below to plug in the power cord.
This product must be earthed. If it should malfunction or break down, earthing provides a path of least
resistance for electric current to reduce the risk of
electric shock. This product’s power cord has an
equipment-earthing conductor and an earthing plug.
IMPORTANT: If the power cord is damaged, it must
be replaced with a manufacturer-recommended
power cord.
1. P
lug the indicated end of the power cord into the
socket on the treadmill.
Socket on Treadmill
AUS
DANGER: Improper connection of
the equipment-earthing conductor can result
in an increased risk of electric shock. Check
with a qualified electrician or serviceman if
you are in doubt as to whether the product
is properly earthed. Do not modify the plug
provided with the product—if it will not fit
the outlet, have a proper outlet installed by a
qualified electrician.
Power Cord
2. P
lug the power cord into an appropriate outlet that
is properly installed and earthed in accordance with
all local codes and ordinances.
Australia
UK
Outlet
GR
Outlet
UK
AUS
FR/SP
GR
RU
17HU
GR
RU
HU
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
You can even listen to your favorite workout music or
audio books with the console’s sound system while you
exercise.
The treadmill console offers an impressive array of
features designed to make your workouts more effective and enjoyable. When you use the manual mode,
you can change the speed and incline of the treadmill
with the touch of a button. As you exercise, the console
will display instant exercise feedback. You can even
measure your heart rate using the handgrip heart rate
monitor or the chest heart rate monitor.
To turn on the power, see page 19. To use the
manual mode, see page 19. To use an onboard
workout, see page 21. To use an iFit workout, see
page 22. To use a set-a-goal workout, see page 23.
To use the sound system, see page 23. To use the
information mode, see page 24.
In addition, the console features a selection of onboard
workouts. Each workout automatically controls the
speed and incline of the treadmill as it guides you
through an effective exercise session. You can also set
a calorie, time, or distance goal.
Note: The console can display speed and distance in
either miles or kilometers. To find which unit of measurement is selected, see THE INFORMATION MODE
on page 24. For simplicity, all instructions in this section refer to kilometers.
The console also features an iFit mode that enables
the treadmill to communicate with your wireless
network through the included iFit module. With the
iFit mode, you can download personalized workouts,
create your own workouts, track your workout results,
race against other iFit users, and access many other
features.
IMPORTANT: If there are sheets of plastic on the
console, remove the plastic. To prevent damage
to the walking platform, wear clean athletic shoes
while using the treadmill. The first time you use
the treadmill, observe the alignment of the walking
belt, and center the walking belt if necessary (see
page 28).
ETNE17812
(NERTL17812)
18
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room temperature before you turn on the power. If you do
not do this, you may damage the console displays
or other electrical components.
1.Insert the key into the console.
Plug in the power cord
(see page 17). Next, locate
the power switch on the
treadmill frame near the
power cord. Press the
power switch into the reset
position.
If the manual mode is not already selected, press
the Manual button to select the manual mode.
See HOW TO TURN ON THE POWER at the left.
2.Select the manual mode.
Reset
3. Start the walking belt.
To start the walking belt, press the Start button, the
Quick Speed increase button, or one of the Quick
Speed buttons numbered 2 through 22.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is displayed in a store. If the displays light as soon as
you plug in the power cord and press the power
switch into the reset position, the demo mode is
turned on. To turn off the demo mode, hold down
the Stop button for a few seconds. If the displays
remain lit, see THE INFORMATION MODE on page
24 to turn off the demo mode.
If you press the Start button or the Quick Speed
increase button, the walking belt will begin to move
at 2 Km/H. As you exercise, change the speed of
the walking belt as desired by pressing the Quick
Speed increase and decrease buttons. Each time
you press one of the buttons, the speed setting will
change by 0.1 Km/H; if you hold down the button,
the speed setting will change in increments of 0.5
Km/H. Note: After you press the button, it may take
a moment for the walking belt to reach the selected
speed setting.
Next, stand on the foot
Key
rails of the treadmill. Find
the clip attached to the key
and slide the clip onto the
waistband
of your clothes.
ETNE17812
(NERTL17812)
Then,
insert the key into the
console. After a moment,
Clip
the displays will light.
IMPORTANT: In an emergency, the key can be
pulled from the console, causing the walking belt
to slow to a stop. Test the clip by carefully taking
a few steps backward; if the key is not pulled from
the console, adjust the position of the clip.
If you press one of the Quick Speed buttons numbered 2 through 22, the walking belt will gradually
change speed until it reaches the selected speed
setting.
To stop the walking belt, press the Stop button. The
time will begin to flash in the display. To restart the
walking belt, press the Start button or the Quick
Speed increase button.
4. Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Quick Incline increase or decrease button or one
of the Quick Incline buttons numbered 0 through
15. Each time you press one of the buttons, the
treadmill will gradually adjust to the selected incline
setting.
19
5.Follow your progress with the displays.
6. Measure your heart rate if desired.
The matrix—When
you select the manual
mode, the matrix will
display a track that
represents 400 m
(1/4 mile). As you exercise, the indicators around the track will appear in
succession until the entire track appears. The track
will then disappear and the indicators will again
begin to appear in succession.
The Cals/Incline display—This display will
show the approximate
number of calories you
have burned. The display will also show the
incline of the treadmill for a few seconds each time
the incline of the treadmill changes.
Note: If you use the handgrip heart rate monitor and the chest heart rate monitor at the same
time, the console will not display your heart
rate accurately. For information about the chest
heart rate monitor, see page 16.
Before using
the handgrip heart
rate monitor,
remove the
sheets of plastic from the
Metal
metal contacts
Contacts
on the pulse
bar. In addition, make
sure that your hands are clean.
To measure your heart rate, stand on the foot
rails and hold the pulse bar with your palms on the
metal contacts; avoid moving your hands. When
your pulse is detected, several dashes will appear
and then your heart rate will be shown. For the
most accurate heart rate reading, continue to
hold the contacts for about 15 seconds.
The Time display—
This display will show
the elapsed time.
Note: When an
onboard workout is
selected, the display
will show the time remaining in the workout instead
of the elapsed time.
7. Turn on the fan if desired.
he Distance disT
play—This display will
show the distance that
you have walked or run.
The fan features multiple speed settings.
Press the fan increase
and decrease buttons
repeatedly to select a
fan speed or to turn off the fan.
The Speed/Pulse
display—This display
will show the speed of
the walking belt. The
display will also show
your heart rate when
you use the handgrip
heart rate monitor or the chest heart rate monitor
(see step 6).
8.When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to zero. The
incline must be at zero or you may damage the
treadmill when you fold it to the storage position. Next, remove the key from the console and
put it in a secure place.
The Center display—This display will show workout instructions.
When you are finished using the treadmill, press
the power switch into the off position and unplug
the power cord. IMPORTANT: If you do not do
this, the treadmill’s electrical components may
wear prematurely.
When an iFit module is
connected to iFit, the
iFit symbol will light in
the center display.
To reset the displays, press the Stop button,
remove the key, and then reinsert the key.
20
HOW TO USE AN ONBOARD WORKOUT
The workout will continue in this way until the last
segment of the profile flashes in the display and the
last segment ends. The walking belt will then slow
to a stop.
1.Insert the key into the console.
See HOW TO TURN ON THE POWER on page 19.
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories
that you burn will depend on various factors
such as your weight. In addition, if you manually change the speed or incline of the treadmill
during the workout, the number of calories you
burn will be affected.
2. Select an onboard workout.
To select an onboard workout, press the Calorie
button, the Incline button, the Intensity button, or
the Speed button repeatedly until the desired workout appears in the display.
When you select an onboard workout, the displays
will show the maximum incline, the duration, the
distance, the maximum speed, and the name of
the workout. In addition, a profile of the speed settings of the workout will appear in the matrix. If you
select a calorie workout, the approximate number
of calories you will burn will appear in the name of
the workout.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the Quick Speed
or Quick Incline buttons; however, when the next
segment of the workout begins, the treadmill
will automatically adjust to the speed and
incline settings for the next segment.
3. Start the workout.
To stop the workout at any time, press the Stop
button. The time will begin to flash in the display. To
resume the workout, press the Start button or the
Quick Speed increase button. The walking belt will
begin to move at 2 Km/H. When the next segment
of the workout begins, the treadmill will automatically adjust to the speed and incline settings for the
next segment.
Press the Start button or the Quick Speed increase
button to start the workout. A moment after you
press the button, the treadmill will automatically
adjust to the first speed and incline settings of the
workout. Hold the handrails and begin walking.
Each workout is divided into segments. One speed
setting and one incline setting are programmed for
each segment. Note: The same speed setting and/
or incline setting may be programmed for consecutive segments.
4.Follow your progress with the displays.
See step 5 on page 20.
5. Measure your heart rate if desired.
During the workout, the
Current Segment
profile will show your
progress. The flashing
segment of the profile
represents the current
segment of the workout. The height of the flashing segment indicates
the speed setting for the current segment. At the
end of each segment, a series of tones will sound
and the next segment of the profile will begin
to flash. If a new speed and/or incline setting is
programmed for the next segment, the new speed
and/or incline setting will appear in the displays for
a few seconds and the treadmill will automatically
adjust to the new speed and/or incline setting.
See step 6 on page 20.
6. Turn on the fan if desired.
See step 7 on page 20.
7.When you are finished exercising, remove the
key from the console.
21
See step 8 on page 20.
HOW TO USE AN IFIT WORKOUT
When you select an iFit workout, the display will
show the duration of the workout, the distance you
will walk or run, the approximate number of calories
you will burn, the name of the workout, and the
maximum speed and incline settings. If you select a
competition workout, the display will count down to
the beginning of the race.
Note: To use an iFit workout, you must have access to
a computer with a USB port and an internet connection. In addition, you must have access to a wireless
network including an 802.11b/g/n router with SSID
broadcast enabled (hidden networks are not supported). An iFit.com membership is also required.
See HOW TO TURN ON THE POWER on page 19.
Note: Some of the iFit buttons may also run demo
workouts. To use the demo workouts, remove the
iFit module from the console and press one of the
iFit buttons.
2. Insert the iFit module into the console.
5. Start the workout.
To insert the iFit module, see the instructions
included with the iFit module.
1.Insert the key into the console.
See step 3 on page 21.
During some workouts, the voice of an audio coach
may guide you through your workout. You can
select a setting for your audio coach (see THE
INFORMATION MODE on page 24).
IMPORTANT: To satisfy exposure compliance
requirements, the antenna and transmitter in
the iFit module must be at least 8 in. (20 cm)
from all persons and must not be near or connected to any other antenna or transmitter.
To stop the workout at any time, press the Stop
button. The time will begin to flash in the display.
To resume the workout, press the Start button or
the Quick Speed increase button. The walking belt
will begin to move at the speed setting for the first
segment of the workout. When the next segment of
the workout begins, the treadmill will automatically
adjust to the speed and incline settings for the next
segment.
3. Select a user.
If more than one user is registered, you can switch
users in the iFit main screen. Press the increase
and decrease buttons next to the Enter button to
select a user.
4. Select an iFit workout.
6.Follow your progress with the displays.
To select an iFit workout, press one of the iFit
buttons. Before some workouts will download, you
must add them to your schedule on www.iFit.com.
See step 5 on page 20.
7. Measure your heart rate if desired.
Press the Map button, the Train button, or the Lose
Wt. button to download the next workout of that
type in your schedule. Press the Compete button to
compete in a race that you have previously
scheduled.
See step 6 on page 20.
8.Turn on the fan if desired.
See step 7 on page 20.
To re-run a recent iFit workout from your schedule,
first press the Track button. Next, press the increase and decrease buttons to select the desired
workout. Then, press the Enter button to start the
workout.
9.When you are finished exercising, remove the
key from the console.
See step 8 on page 20.
For more information about the iFit mode, go to
www.iFit.com.
Note: If there are no workouts of the selected type
in your schedule, the next workout in your schedule
will be downloaded.
For more information on the iFit workouts,
please see www.iFit.com.
22
HOW TO USE A SET-A-GOAL WORKOUT
5. Measure your heart rate if desired.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 19.
6. Turn on the fan if desired.
2. Select a set-a-goal workout.
To select a set-a-goal workout, press the Set A
Goal button on the console.
7.When you are finished exercising, remove the
key from the console.
Use the increase and decrease buttons next to the
Enter button to set a calorie, time, or distance goal,
and then press the Enter button. Next, press the
increase and decrease buttons next to the Enter
button to select a goal. Press the Quick Speed
and Quick Incline buttons to select the speed and
incline for the workout. The screen will show the
duration and distance of the workout, and the
approximate number of calories you will burn during the workout.
See step 6 on page 20.
See step 7 on page 20.
See step 8 on page 20.
HOW TO USE THE SOUND SYSTEM
To play music or audio books through the console
sound system while you exercise, plug a 3.5 mm male
to 3.5 mm male audio cable (not included) into the jack
on the console and into a jack on your MP3 player,
CD player, or other personal audio player; make sure
that the audio cable is fully plugged in. Note: To
purchase an audio cable, see your local electronics
store.
3. Start the workout.
Press the Start button to start the workout. A
moment after you press the button, the walking belt
will begin to move. Hold the handrails and begin
walking.
The workout will function in the same way as the
manual mode (see pages 19 and 20).
Next, press the play button on
your personal audio player.
Adjust the volume level using
the volume increase and
decrease buttons on the console or the volume control
on your personal audio player.
The workout will continue until you reach the goal
that you set. The walking belt will then slow to a
stop.
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat
surface and instead of on the console.
Note: The calorie goal is an estimate of the
number of calories that you will burn during the
workout. The actual number of calories that you
burn will depend on various factors such as
your weight.
4. Follow your progress with the displays.
See step 5 on page 20.
23
THE INFORMATION MODE
displays will remain lit, although the buttons will not
function. If the demo mode is turned on, the word
ON will appear in the center display. To turn on or
turn off the demo mode, press the Enter button.
The console features an information mode that keeps
track of treadmill information and allows you to personalize console settings.
CONTRAST LVL—Press the Quick Incline
increase and decrease buttons to adjust the contrast level of the displays.
1. Select the information mode.
To select the information mode, hold down the Stop
button while inserting the key into the console, and
then release the Stop button. When the information
mode is selected, the following information will be
shown:
If a module is connected, you may also select
the following screens:
MODULE—If an iFit module is connected, the
display will show the word WIFI. If a USB module is
connected, the display will show the word USB/SD.
The Time display will
show the total number
of hours that the treadmill has been used.
AUDIO COACH—To turn on or turn off the audio
coach, press the Enter button.
If an iFit module is connected, you may also
select the following screens:
The Distance display
will show the total
number of kilometers or
miles that the walking
belt has moved.
START MODE—The start mode will appear when
you insert the key into the console. Press the Enter
button to select the manual mode or the iFit mode
as the start mode.
2. Select the optional screens.
CHECK WIFI—Press the Enter button. The center
display will show the software version number,
the network SSID, the network encryption type,
the wireless signal strength, the IP address of
the module, the number of registered users and
their names, and the results of the DNS lookup.
To return to the information mode, remove the key
from the console and repeat the instructions near
the beginning of this page.
While the information mode is selected, press the
decrease button next to the Enter button to select
each of the following screens in the center display:
UNITS—To change the
unit of measurement,
press the Enter button. To view distance in
miles, select ENGLISH.
To view distance in
kilometers, select METRIC.
SEND/OBTAIN DATA—To send and receive workouts, workout logs, and updates, press the Enter
button. When the process is finished, the words
TRANSFERS DONE will appear in the display.
DEMO MODE—The console features a display
demo mode, designed to be used if the treadmill
is displayed in a store. While the demo mode is
turned on, the console will function normally when
you plug in the power cord, press the power switch
into the reset position, and insert the key into the
console. However, when you remove the key, the
3. Exit the information mode.
To exit the information mode, remove the key from
the console.
24
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL
HOW TO MOVE THE TREADMILL
To avoid damaging the treadmill, adjust the incline
to zero before you fold the treadmill. Then, remove
the key and unplug the power cord. CAUTION: You
must be able to safely lift 45 lbs. (20 kg) to raise,
lower, or move the treadmill.
efore moving the treadmill, fold it as described at the
B
left. CAUTION: Make sure that the latch knob is
locked in the storage position. Moving the treadmill
may require two people.
1. Hold the frame and one of the handrails, and place
one foot against a wheel.
1. Hold the metal frame firmly in the location shown
by the arrow below. CAUTION: Do not hold the
frame by the plastic foot rails. Bend your legs
and keep your back straight.
1
Frame
1
Handrail
Frame
Wheel
2. Pull back on the handrail until the treadmill will roll
on the wheels, and carefully move it to the desired
location. CAUTION: Do not move the treadmill
without tipping it back, do not pull on the frame,
and do not move the treadmill over an uneven
surface.
2.Raise the frame until the latch knob locks in the
storage position. CAUTION: Make sure that the
latch knob locks.
2
3. Place one foot against a wheel, and carefully lower
the treadmill.
Frame
HOW TO LOWER THE TREADMILL FOR USE
1.
See drawing 2. Hold the upper end of the treadmill
with your right hand. Then, pull the latch knob to
the left and hold it. IMPORTANT: Do not turn the
latch knob. If necessary, push the frame forward
slightly. Pivot the frame downward a few inches,
and release the latch knob.
Latch
Knob
See drawing 1 at the left. Hold the metal frame
2.
firmly with both hands, and lower it to the floor.
CAUTION: Do not hold the frame by the plastic
foot rails, and do not drop the frame. Bend your
legs and keep your back straight.
To protect the floor or carpet, place a mat under the
treadmill. Keep the treadmill out of direct sunlight.
Do not leave the treadmill in the storage position in
temperatures above 85° F (30° C).
25
TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.
c.Remove the key from the console, and then
reinsert it.
d.If the treadmill still will not run, please see the front
cover of this manual.
SYMPTOM: The power does not turn on
SYMPTOM: The console displays remain lit when
you remove the key from the console
a.Make sure that the power cord is plugged into a
properly earthed outlet (see page 17). If an extension cord is needed, use only a 3-conductor,
14-gauge (1 mm2) cord that is no longer than 5 ft.
(1.5 m).
a.The console features a display demo mode,
designed to be used if the treadmill is displayed in
a store. If the displays remain lit when you remove
the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a
few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 24 to turn off the
demo mode.
b.After the power cord has been plugged in, make
sure that the key is inserted into the console.
c.Check the power switch located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
power switch, wait for five minutes and then press
the switch back in.
SYMPTOM: the displays of the console do not
function properly
a.Remove the key from the console and unplug
the power cord.
c
Tripped
Reset
emove the five #8 x 3/4" Hood Screws (15).
R
Carefully slide the Motor Hood (65) off.
65
SYMPTOM: The power turns off during use
15
15
15
a.Check the power switch (see the drawing above).
If the switch has tripped, wait for five minutes and
then press the switch back in.
b.Make sure that the power cord is plugged in. If the
power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
15
26
SYMPTOM: The walking belt slows when walked on
Locate the Reed Switch (52) and the Magnet (51)
on the left side of the Pulley (50). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the #8 x 3/4" Tek Screw (13), move
the Reed Switch slightly, and then retighten the
Screw. Reattach the Motor Hood (not shown) with
the #8 x 3/4" Hood Screws (not shown) and run the
treadmill for a few minutes to check for a correct
speed reading.
If an extension cord is needed, use only a 3-cona.
ductor, 14-gauge (1 mm2) cord that is no longer
than 5 ft. (1.5 m).
b.If the walking belt is overtightened, treadmill performance may decrease and the walking belt may
become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is properly tightened.
Top
View
52
13
51
50
3 mm
b
5–7 cm
SYMPTOM: The incline of the treadmill does not
change correctly
a. Hold down the Stop button and the Quick Speed
increase button, insert the key into the console,
and then release the Stop button and the Quick
Speed increase button. Press the Stop button
and then press the Quick Incline increase or
decrease button. The treadmill will automatically
rise to the maximum incline level and then return to
the minimum level. This will recalibrate the incline
system. If the incline does not begin calibrating,
press the Stop button again, and then press the
Incline increase or decrease button again. When
the incline is calibrated, remove the key from the
console.
Idler Roller Screws
c.Your treadmill features a walking belt coated with
high-performance lubricant. IMPORTANT: Never
apply silicone spray or other substances to
the walking belt or the walking platform unless
instructed to do so by an authorized service
representative. Such substances may deteriorate the walking belt and cause excessive wear.
If you suspect that the walking belt needs more
lubricant, see the front cover of this manual.
d.If the walking belt still slows when walked on, see
the front cover of this manual.
27
SYMPTOM: The walking belt is not centered
between the foot rails
SYMPTOM: The walking belt slips when walked on
a. F
irst, remove the key and UNPLUG THE POWER
CORD. Using the hex key, turn both idler roller
screws clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to
7 cm) off the walking platform. Be careful to keep
the walking belt centered. Then, plug in the power
cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking belt is properly tightened.
IMPORTANT: If the walking belt rubs against the
foot rails, the walking belt may become damaged.
a. F
irst, remove the key and UNPLUG THE POWER
CORD. If the walking belt has shifted to the left,
use the hex key to turn the left idler roller screw
clockwise 1/2 of a turn; if the walking belt has
shifted to the right, turn the left idler roller screw
counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the
power cord, insert the key, and run the treadmill
for a few minutes. Repeat until the walking belt is
centered.
a
a
Foot Rails
28
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise; never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each week,
if desired. Remember, the key to success is to make
exercise a regular and enjoyable part of your everyday
life.
29
PART LIST
Model No. HETL13913.0 R0613A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
#8 x 1/2" Screw
3/8" x 2" Bolt
3/8" x 1 1/4" Screw
#10 x 3/4" Screw
#10 Star Washer
#8 x 1/2" Silver Screw
3/8" x 1 3/4" Bolt
5/16" Star Washer
3/8" Nut
3/8" Star Washer
5/16" x 5/8" Screw
5/16" x 2 3/4" Screw
#8 x 3/4" Tek Screw
#8 x 3/4" Screw
#8 x 3/4" Hood Screw
1/4" Roller Screw
Key/Clip
#8 x 1 3/4" Screw
#8 x 7/16" Screw
5/16" Motor Screw
Chest Strap
3/8" x 2 3/4" Screw
5/16" x 1 3/4" Shoulder Bolt
1/4" x 1 1/4" Screw
#8 x 1" Screw
#8 x 3/4" Pan Tek Screw
3/8" x 1 1/2" Hex Head Bolt
3/8" x 2" Hex Head Bolt
Base
1/4" Star Washer
5/16" Flat Washer
Incline Frame Washer
5/16" Nut
Hood Clip
Platform Grommet
3/8" Jam Nut
Base Pad
Isolator Top
Isolator
Spring
Isolator Bottom
Left Foot Rail
Warning Decal
Walking Platform
Walking Belt
Right Foot Rail
Belt Guide
1/2" x 2 1/4" Bolt
Reed Switch Clip
Drive Roller/Pulley
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Magnet
Reed Switch
Cable Tie
Storage Latch
Drive Motor
Motor Belt
Frame
Right Rear Foot
Left Rear Foot
#8 Star Washer
3/8" x 1" Bolt
Idler Roller
#8 x 5/8" Screw
Incline Stop Bracket
Motor Hood
Hood Accent
Incline Motor
Incline Frame Insert
Incline Frame
Controller
Electronics Bracket
Hood Post
Power Switch
Power Cord
Sensor
Belly Pan
Left Handrail Cover
Left Handrail Insert
Handrail
Ground Wire
Pulse Crossbar
Right Handrail Insert
Right Handrail Cover
Left Upright
Right Upright
Console Clamp
#10 x 1/2" Screw
Left Base Cover
Right Base Cover
Grommet
Upright Wire
Right Wheel Cap
Wheel
Caution Decal
Left Tray
Right Tray
#8 x 1/2" Console Ground Screw
Console Base
Wire Tie
Console
14
2
4
4
4
12
2
4
6
8
4
4
13
35
5
2
1
2
4
2
1
4
4
1
4
12
1
1
1
1
4
2
4
3
4
2
4
4
4
4
4
1
1
1
1
1
2
2
1
1
30
1
1
4
1
1
1
1
1
1
6
2
1
6
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
2
6
1
1
1
1
1
2
2
1
1
1
1
1
1
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
104
105
106
107
Console Frame
Motor Bushing
#8 Ground Bolt
#8 Nut
Filter Bracket
Filter
Motor Isolator
108
109
110
111
112
113
*
Frame Endcap
Frame Endcap Cover
Left Wheel Cap
Receptacle
Grounding Bracket
1/2" Nut
User’s Manual
1
2
1
1
1
1
1
1
1
1
1
1
2
–
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
31
16
32
35
31
33
23
26
41
40
39
38
62
43
59
26
41
26
40
39
38
16
63
45
44
23
63
42
46
19
26
58
47
15
31
33
35
63
31
63
33
9
57
35
48
23
49
13
2
41
26
40
39
38
63
51
50
52
18
63
41
26
40
19
38
54
55
9
24
30
35
31
33
15
6
6
47
23
20
6
103
104
102
39
56
102
48
53
60
106
107
2
6
18
105
60
60
EXPLODED DRAWING A
Model No. HETL13913.0 R0613A
EXPLODED DRAWING B
Model No. HETL13913.0 R0613A
15
15
15
65
66
69
6
9
67
61
68
108
64
28
32
27
113
61
9
32
70
13
14
6 60
87
14
6
112
113
68
71
14
13
14
87
14
14
72
14
109
87
87
87
34
34
14
87
26
72
14 111
73
26
34
74
76
26
33
EXPLODED DRAWING C
Model No. HETL13913.0 R0613A
12
78
8
77
11
79
4
5
14
97
80
81
1
1
83
84
4
12
5
8
1
1
11
82
3
22
10
10
22
10
9
91
14
90
6
13
37
94
37
7
93
94
89
14
36 110
85
79
22
9
13
10
29
88
7
93
10
22
37
92
14
36
34
37
13
10
13
3
EXPLODED DRAWING D
Model No. HETL13913.0 R0613A
1
98
95
14
1
14
1
99
14
14
1
14
14
100
14
14
14
96
1
14
1
101
86
25
86
21
17
75
35
25
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED DRAWING
near the end of this manual)
RECYCLING INFORMATION
This electronic product must not be disposed of in municipal waste. To
preserve the environment, this product must be recycled after its useful life
as required by law.
Please use recycling facilities that are authorized to collect this type of waste in
your area. In doing so, you will help to conserve natural resources and improve
European standards of environmental protection. If you require more information
about safe and correct disposal methods, please contact your local city office or
the establishment where you purchased this product.
Part No. 347100 R0613A
Printed in China © 2013 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement