User Manual Draco tera K480 Series

User Manual Draco tera K480 Series
User Manual
Edition: 2013-08-14
Draco tera
Model:
K480 Series
Firmware:
V02.10
IHSE GmbH
Maybachstrasse 11
88094 Oberteuringen
Germany
info@ihse.de
www.ihse.de
Tel. +49 7546-9248-0
Fax +49 7546-9248-48
Draco tera
Copyright
© 2013. All rights reserved. This information may not be reproduced in any
manner without the prior written consent of the manufacturer.
Information in this document is subject to change without notice.
Trademarks
All trademark and trade names mentioned in this document are
acknowledged to be the property of their respective owners.
Disclaimer
While every precaution has been taken during preparation of this manual,
the manufacturer assumes no liability for errors or omissions. Neither does
the manufacturer assume any liability for damages resulting from the use
of the information contained herein.
The manufacturer reserves the right to change specifications, functions, or
circuitry of the product without notice.
The manufacturer cannot accept liability for damage due to misuse of the
product or due to any other circumstances outside the manufacturer’s
control (whether environmental or installation related). The manufacturer
shall not be liable for any loss, damage, or injury arising directly, indirectly,
incidentally, or consequently from the use of this product.
2
2013-08-14
Contents
Contents
1
About This Manual ....................................................................... 8
1.1
Scope.................................................................................. 8
1.2
Validity ................................................................................ 8
1.3
Cautions and Notes ............................................................ 8
1.4
Spellings ............................................................................. 8
2
Safety Instructions ....................................................................... 9
3
Description ................................................................................. 10
3.1
Application ........................................................................ 10
3.2
Access Options ................................................................. 10
3.3
System Overview .............................................................. 11
3.4
Product Range .................................................................. 12
3.5
Accessories....................................................................... 12
3.6
Device Views .................................................................... 14
3.7
4
Draco tera 288 Port............................................. 14
3.6.2
Draco tera 160 Port............................................. 16
3.6.3
Draco tera 80 Port............................................... 17
3.6.4
Draco tera 48 Port............................................... 18
Diagnostics and Status ..................................................... 19
3.7.1
Status LEDs ........................................................ 19
3.7.2
Port Status .......................................................... 26
3.7.3
Extender OSD..................................................... 30
3.7.4
Network Status.................................................... 31
3.7.5
Firmware Status Matrix ....................................... 34
3.7.6
Firmware Status Extender................................... 36
3.8
Trace Function .................................................................. 37
3.9
Syslog Monitoring ............................................................. 38
3.10
SNMP................................................................................ 40
3.11
System Check ................................................................... 44
Installation .................................................................................. 46
4.1
2013-08-14
3.6.1
Package Contents............................................................. 46
3
Draco tera
5
4.2
System Setup.................................................................... 46
4.3
Example Applications........................................................ 47
KVM Matrix ......................................................... 48
4.3.2
Video Matrix ........................................................ 49
4.3.3
Parallel Operation (Stacking) .............................. 50
4.3.4
Cascading ........................................................... 52
Configuration.............................................................................. 53
5.1
Command Mode ............................................................... 53
5.2
Control Options ................................................................. 55
5.3
5.4
5.5
5.6
5.7
4
4.3.1
5.2.1
Control via OSD .................................................. 55
5.2.2
Control via Java Tool .......................................... 60
5.2.3
Control via Serial Interface.................................. 69
Assignment ....................................................................... 69
5.3.1
Virtual CPU ......................................................... 69
5.3.2
Virtual Console.................................................... 72
System Settings ................................................................ 75
5.4.1
System Data ....................................................... 75
5.4.2
Automatic ID ....................................................... 79
5.4.3
Access ................................................................ 82
5.4.4
Switch ................................................................. 86
5.4.5
Network............................................................... 90
5.4.6
Date and Time .................................................... 94
User Settings .................................................................... 97
5.5.1
User .................................................................... 97
5.5.2
Favorite List Users ............................................ 100
5.5.3
User Macros...................................................... 103
Extender Settings............................................................ 107
5.6.1
Creating Flex-Port Extender Unit ...................... 109
5.6.2
Creating Fixed Port Extender Units................... 110
5.6.3
Deleting Flex-Port Extender Units..................... 110
5.6.4
Deleting Fixed Port Extender Units ................... 110
CPU Settings .................................................................. 111
2013-08-14
Contents
5.8
5.9
5.10
5.11
5.12
6
5.8.1
CON Devices .................................................... 115
5.8.2
Mouse and Keyboard ........................................ 120
5.8.3
Extender OSD................................................... 123
5.8.4
Favorite List Consoles ...................................... 126
5.8.5
Console Macros ................................................ 128
5.8.6
Parallel Operation ............................................. 132
5.8.7
Multi-Screen Control ......................................... 135
Saving and Loading of Configurations ............................ 139
5.9.1
Active Configuration .......................................... 139
5.9.2
Saving of Configurations (internal) .................... 139
5.9.3
Loading of Configurations (internal) .................. 142
5.9.4
Saving of Configurations (external) ................... 144
5.9.5
Loading of Configurations (external) ................. 145
Export and Import Options .............................................. 146
5.10.1
Export Options .................................................. 146
5.10.2
Import Options .................................................. 147
Firmware Update ............................................................ 148
5.11.1
Matrix Update.................................................... 148
5.11.2
Extender Update ............................................... 150
License Management...................................................... 154
Operation .................................................................................. 156
6.1
2013-08-14
Console Settings ............................................................. 115
Operation via 'Hot Keys'.................................................. 157
6.1.1
Direct Switching ................................................ 157
6.1.2
Scan Mode........................................................ 159
6.1.3
Function Keys <F1>–<F16>.............................. 159
6.1.4
Addressing of Main and Sub Matrices .............. 160
6.2
KVM-Switching................................................................ 161
6.3
Extended Switching ........................................................ 164
6.4
CON Switch .................................................................... 169
6.5
Multi-Screen Control ....................................................... 171
6.6
USB 2.0 Switching .......................................................... 172
5
Draco tera
6.7
Presets............................................................................ 173
6.8
Serial Interface................................................................ 174
6.9
Power On and Power Down Functions ........................... 175
6.10
7
Restart .............................................................. 175
6.9.2
Factory Reset.................................................... 176
6.9.3
Power Down...................................................... 176
Summary of Keyboard Commands ................................. 177
Specifications ........................................................................... 179
7.1
7.2
7.3
7.4
7.5
6
6.9.1
Interfaces ........................................................................ 179
7.1.1
DVI-D Single Link.............................................. 179
7.1.2
USB-HID ........................................................... 179
7.1.3
RJ45 (Network) ................................................. 180
7.1.4
RS-232 (Serial) ................................................. 180
7.1.5
RJ45 (Interconnect) .......................................... 180
7.1.6
Fiber SFP Type LC (Interconnect) .................... 180
7.1.7
SDI (Interconnect)............................................. 181
Interconnect Cable .......................................................... 181
7.2.1
Cat X ................................................................. 181
7.2.2
Fiber.................................................................. 182
7.2.3
Coaxial .............................................................. 183
Supported Peripherals .................................................... 184
7.3.1
KVM Extenders with Cat X Connection............. 184
7.3.2
KVM Extenders with Fiber Connection (SingleMode)................................................................ 185
7.3.3
USB 2.0 Extenders with Cat X Connection ....... 186
7.3.4
USB 2.0 Extenders with Fiber Connection (SingleMode)................................................................ 187
Connector Pinouts .......................................................... 188
7.4.1
CPU Board........................................................ 188
7.4.2
I/O Port Cat X.................................................... 189
7.4.3
I/O Port SFP...................................................... 189
7.4.4
I/O Port SDI....................................................... 190
Power Supply.................................................................. 190
2013-08-14
Contents
7.6
8
9
10
11
12
Environmental Conditions ............................................... 190
7.7
Size ................................................................................. 191
7.8
Shipping Weight .............................................................. 192
7.9
MTBF .............................................................................. 193
Maintenance ............................................................................. 194
8.1
Power Supply Units......................................................... 194
8.2
Fan trays ......................................................................... 194
8.3
CPU Board...................................................................... 195
8.4
I/O-Board ........................................................................ 195
8.5
Filter Pads....................................................................... 196
Troubleshooting ....................................................................... 197
9.1
External Failure............................................................... 197
9.2
Video Interference........................................................... 197
9.3
Malfunction of Fans......................................................... 198
9.4
Malfunction of Power Supply Units ................................. 198
9.5
Network Error.................................................................. 198
9.6
Failure at the Matrix ........................................................ 199
9.7
Blank Screen................................................................... 200
Technical Support .................................................................... 201
10.1
Support Checklist ............................................................ 201
10.2
Shipping Checklist .......................................................... 201
Certificates................................................................................ 202
11.1
CE Declaration Of Conformity......................................... 202
11.2
North American Regulatory Compliance ......................... 203
11.3
Product Safety ................................................................ 203
11.4
WEEE ............................................................................. 204
11.5
RoHS/RoHS 2................................................................. 204
Glossary.................................................................................... 205
12.1
Matrix specific Glossary .................................................. 208
Pos: 1 /806-IHSE/Zu diesem Handbuch/ATB_Zu diesem Handbuch @ 5\mod_1278573163276_6.doc @ 41510 @ 1222 @ 1
2013-08-14
7
Draco tera
1
About This Manual
1.1
Scope
This manual describes how to install your Draco tera, how to operate it
and how to perform trouble shooting.
1.2
Validity
This manual is valid for all devices listed on the front page. The product
code is printed on the base of the devices.
1.3
Cautions and Notes
The following symbols are used in this manual:
This symbol indicates an important operating instruction that should be
followed to avoid any potential damage to hardware or property, loss of
data, or personal injury.
This symbol indicates important information to help you make the best use
of this product.
This symbol indicates best practice information to show recommended
and optimal ways to use this product in an efficient way.
Pos: 2 /806-IHSE/Zu diesem Handbuch/ATB_Schreibweisen @ 7\mod_1309932297321_6.doc @ 52440 @ 2 @ 4
1.4
Spellings
You can find the following spellings in the manual:
Spelling
Description
<key>
Description of a key on the keyboard
<key> + <key>
Press keys simultaneously
<key>, <key>
Press keys successively
2x <key>
Press key 2x in quick succession
(cf. mouse double click)
Menu item
Description of a menu item in the software
Menu item > Menu item
Select menu items successively
Bold print
Description of terms that are used in the
device software
Pos: 3 /806-IHSE/Sicherheitshinweise/480_Sicherheitshinweise @ 7\mod_1310643167940_6.doc @ 54240 @ 1 @ 1
8
2013-08-14
Safety Instructions
2
Safety Instructions
To ensure reliable and safe long-term operation of your Draco tera please
note the following guidelines:
Installation
 Only use the device according to this User Manual. Otherwise the
provided safety can be affected.
 Only use in dry, indoor environments.
 The Draco tera and the power supply units can get warm. Do not
situate them in an enclosed space without any airflow.
 Do not obscure ventilation holes.
 Only use power supplies originally supplied with the product or
manufacturer-approved replacements. Do not use a power supply if it
appears to be defective or has a damaged chassis.
 Connect all power supplies to grounded outlets. In each case, ensure
that the ground connection is maintained from the outlet socket
through to the power supply's AC power input.
 Do not connect the link interface to any other equipment, particularly
network or telecommunications equipment.
 Only connect devices to the serial interface that are sufficiently
secured against short circuit currents and false voltages at the serial
interface.
 To disconnect the Draco tera from the power supply, remove the
power cord cables of all power supply units that are in use or set the
power switch (if available) to the off-position.
 Take any required ESD precautions.
In order to disconnect the device completely from the electric circuit, all
power cables have to be removed.
Repair
 Do not attempt to open or repair a power supply unit.
 Do not attempt to open or repair the Draco tera. There are no user
serviceable parts inside.
 Please contact your dealer or manufacturer if there is a fault.
Pos: 4 /806-IHSE/Beschreibung/UEB_Beschreibung @ 5\mod_1278573379151_6.doc @ 41546 @ 1 @ 1
2013-08-14
9
Draco tera
3
Description
Pos: 5 /806-IHSE/Beschreibung/Verwendungszweck/480-xx @ 7\mod_1309932919008_6.doc @ 52458 @ 2 @ 1
3.1
Application
The Draco tera matrix is used to establish connections from consoles
(monitor, keyboard, mouse, and other peripheral devices) to various
sources (computer, CPU).
In a maximum configuration, up to 288 independent ports can be defined
and switched either as a console or a CPU.
The Draco tera matrix is mainly specified for the use with extenders that
are able to transmit video, KVM and USB 2.0 signals. But it can be also
run as a video matrix.
The connection between the matrix and the peripheral devices, such as
KVM extenders or video sources, can be made by Cat X, fiber or coaxial
cables.
The matrix serves as a repeater. Thus, the matrix can be run at a
maximum distance of 10 km from the consoles and 10 km from the
sources.
Pos: 6 /806-IHSE/Beschreibung/Zugriffsmöglichkeiten/480-xx @ 7\mod_1309933105946_6.doc @ 52477 @ 2 @ 1
3.2
Access Options
You have the following options to access the Draco tera for configuration
and operation:
Access Option
Symbol
OSD
Java tool
Serial interface
Pos: 7 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
10
2013-08-14
Description
Pos: 8 /806-IHSE/Beschreibung/System-Übersicht /480-xx @ 7\mod_1309933171196_6.doc @ 52495 @ 2 @ 1
4.3
3.3
System Overview
A Draco tera matrix system consists of a Draco tera matrix and, for KVM
applications, of one or more CPU Units / CON Units. The Draco tera
matrix is connected to the CPU Units / CON Units by interconnect cables
or connected directly to the video devices where used as a video matrix.
The CPU units are connected directly to the sources (computer, CPU) by
the provided cables.
Monitor(s), keyboard and mouse are connected to the CON units.
The communication between the Draco tera matrix and the CPU Units /
CON Units takes place over the respective interconnect cables.
1
2
3
4
3
5
6
System Overview (exemplary)
1
Source (computer, CPU)
2
CPU Units
3
Interconnect cable
4
Draco tera matrix
5
CON Units
6
Console (monitor, keyboard, mouse)
See Chapter 4.3, Page 47 for installation examples.
Pos: 9 /806-IHSE/Beschreibung/Gerätetypen/480-xx @ 7\mod_1309934329227_6.doc @ 52513 @ 2 @ 1
2013-08-14
11
Draco tera
3.4
Product Range
Part No.
Description
K480-288
Draco tera matrix with 288 ports, empty, free
configuration
K480-160
Draco tera matrix with 160 ports, empty, free
configuration
K480-080
Draco tera matrix with 80 ports, empty, free
configuration
K480-048
Draco tera matrix with 48 ports, empty, free
configuration
Pos: 10 /806-IHSE/Beschreibung/Zubehör/480-xx @ 7\mod_1309934367915_6.doc @ 52531 @ 2 @ 1
3.5
12
Accessories
Part No.
Description
480-B1
Java-Tool, Extended Switching, Presets
480-B2
480-B1, API
480-B3
SNMP, Syslog
480-B4
Cascading, stacking
480-B5
Multi-Screen Control
480-C8
Draco tera Cat X I/O board
480-S8
Draco tera fiber I/O board, Single-mode
480-V8
Draco tera fiber I/O board, Single-mode, 3,125 Gbit/s
480-SDI16
Draco tera I/O board video
480-X8
Draco tera fiber I/O board, empty, free configuration
480-CTRL
Draco tera CPU board
459-1C
Cat X GBIC for the use with Draco tera
459-1S
Single-mode GBIC for the use with Draco minor /
major / tera
459-1V
Single-mode GBIC for the use with Draco tera
(3.125 Gbit/s)
459-2FT
Single-mode GBIC (transmitter), dual-unidirectional,
for the use with Draco tera (HD-SDI)
459-3FT
Single-mode GBIC (transmitter), dual-unidirectional,
for the use with Draco tera (3G-SDI)
459-2BT
Coax GBIC (transmitter), dual-unidirectional, for the
use with Draco tera (HD-SDI)
2013-08-14
Description
Part No.
Description
459-3BT
Coax GBIC (transmitter), dual-unidirectional, for the
use with Draco tera (3G-SDI)
459-2FR
Single-mode GBIC (receiver), dual-unidirectional, for
the use with Draco tera (HD-SDI)
459-3FR
Single-mode GBIC (receiver), dual-unidirectional, for
the use with Draco tera (3G-SDI)
459-2BR
Coax GBIC (receiver), dual-unidirectional, for the use
with Draco tera (HD-SDI)
459-3BR
Coax GBIC (receiver), dual-unidirectional, for the use
with Draco tera (3G-SDI)
459-BMB
Adapter cable BNC to mini BNC to adapt regular BNC
cables to mini BNC SFP
480-FAN160
Draco tera 288/160 fan tray (spare part)
480-FAN80
Draco tera 80 fan tray (spare part)
480-FAN48
Draco tera 48 fan tray (spare part)
480-RED160
Draco tera 288/160 plug-in power supply unit (spare
part or redundancy)
480-RED80
Draco tera 80 plug-in power supply unit (spare part or
redundancy)
480-FLTR160
Draco tera 288/160 filter pads as consumable supply
480-FLTR80
Draco tera 80 filter pads as consumable supply
480-FLTR48
Draco tera 48 filter pads as consumable supply
You can find appropriate extenders or other components in Chapter 7.3,
Page 184)..
Pos: 11 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
13
Draco tera
3.6
Device Views
The following views of the Draco tera matrix illustrate the various available
chassis types.
Pos: 13 /806-IHSE/Beschreibung/Geräteansichten/480-xx/Draco tera 288 Port @ 7\mod_1309934693586_6.doc @ 52550 @ 3 @ 1
3.6.1
Draco tera 288 Port
FAN TRAY
OK
HS
FILTER
FAN TRAY
OK
HS
+
+
1
2
3
4
5 6
7
8
Front View
14
2013-08-14
Description
1
Slot for power supply unit 1
2
Slot for fan tray 1
3
Slot for power supply unit 2
4
Slot for fan tray 2
5
Slot for I/O boards #1–36
6
Slot for power supply unit 3
7
Slot for CPU board
8
Grounding
Pos: 14 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
15
Draco tera
Pos: 15 /806-IHSE/Beschreibung/Geräteansichten/480-xx/Draco tera 160 Port @ 7\mod_1309934740805_6.doc @ 52568 @ 3 @ 1
3.6.2
Draco tera 160 Port
FAN TRAY
OK
HS
FILTER
FAN TRAY
OK
HS
+
+
1
2
3
4
5 6
7
8
Front View
1
Slot for power supply unit 1
2
Slot for fan tray 1
3
Slot for power supply unit 2
4
Slot for fan tray 2
5
Slot for I/O boards #1–20
6
Slot for power supply unit 3
7
Slot for CPU board
8
Grounding
Pos: 16 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
16
2013-08-14
Description
Pos: 17 /806-IHSE/Beschreibung/Geräteansichten/480-xx/Draco tera 80 Port @ 7\mod_1309934775696_6.doc @ 52586 @ 3 @ 1
Draco tera 80 Port
FILTER
TOP
3.6.3
FAN TRAY
HS
OK
1
2
3
4
5
FAN TRAY
HS
OK
6 7
Front View
1
Slot for fan tray
2
Slot for power supply unit 1
3
Slot for I/O boards #1–10
4
Slot for power supply unit 2
5
Slot for CPU board
6
Slot for air filter
7
Slot for fan tray 2
Pos: 18 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
17
Draco tera
Pos: 19 /806-IHSE/Beschreibung/Geräteansichten/480-xx/Draco tera 48 Port @ 7\mod_1311324635246_6.doc @ 54330 @ 3 @ 1
Draco tera 48 Port
FILTER
TOP
3.6.4
FAN TRAY
HS
OK
1
2
3
4
5
FAN TRAY
HS
OK
6 7
Front View
1
Slot for fan tray
2
Slot for power supply unit 1
3
Slot for I/O boards #1–6
4
Slot for power supply unit 2
5
Slot for CPU board
6
Slot for air filter
7
Slot for fan tray 2
Pos: 20 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
18
2013-08-14
Description
Pos: 21 /806-IHSE/Beschreibung/Status/UEB_Diagnose_und_Status @ 7\mod_1309935121461_6.doc @ 52641 @ 2 @ 4
3.7
Diagnostics and Status
Pos: 22 /806-IHSE/Beschreibung/Diagnose LEDs/480-xx @ 7\mod_1309934983180_6.doc @ 52622 @ 3 @ 1
3.7.1
Status LEDs
The Draco tera components are fitted with the following LEDs for overall
status indication:
CPU Board
Front View
2013-08-14
19
Draco tera
Status LEDs on CPU board:
Pos. LED
1
2
Status 1
Status 2
Status
Description
White
CPU board is in registration process
Blue
flashing
Registration at the matrix is started
Red
flashing
Registration in progress
Green
flashing
Operating condition
Green
CPU board de-registered
White
CPU board is in registration process
Red
flashing
Registration at the matrix is started
Off
Operating condition
Due to variations in LED type "white" might also appear as light purple or
light blue.
20
2013-08-14
Description
I/O Board
Cat X
SFP Fiber
SFP Coax
Front View
2013-08-14
21
Draco tera
Status LEDs at I/O boards:
Pos. LED
1
2
22
Status 1
Status 2
Status
Description
Light
blue
I/O board in boot process
Red
flashing
I/O board in registration process
Red/
Yellow
flashing
I/O board in Service Mode or firmware
conflict with CPU board
Green
flashing
Operating condition, I/O board
registered at the matrix
Green
I/O board de-registered (locking pin
pulled out)
White
I/O board in boot process
Blue
I/O board in registration process
Blue
flashing
Operating condition, communication
active with CPU board active
Red
flashing
I/O board de-registered (locking pin
pulled out)
2013-08-14
Description
Ports I/O Board
Cat X
SFP Fiber
SFP Coax
Front View
1
Status LED 1
2
Status LED 2
Status LEDs at the ports of the I/O boards:
Pos. LED
1
2
2013-08-14
Status
Description
Link status
(orange)
Off
Port not activated
Flashing
Port activated, no connection via
interconnect cable
Link status
(green)
Off
Port not activated
Flashing
Port activated, no connection via
interconnect cable
On
Connection via interconnect cable ok,
data traffic active
23
Draco tera
Fan Tray
FAN TRAY
OK
HS
1
2
3
Front View
1
Status LED 1
2
Status LED 1
3
Hot Swap LED
Status LEDs of the fan trays:
Pos. LED
24
Status
Description
1
Status 1
(green)
On
Operating condition
2
Status 2
(red)
Off
Operating condition
3
Hot Swap
(blue)
On
Error indication
Off
Hot Swap option deactivated
On
Hot Swap option activated
2013-08-14
Description
Power Supply Unit Draco tera 288/160
1 2 3
Front View
Status LEDs of the power supply units
Pos. LED
Status
Description
1
AC Input
OK (green)
On
Operating condition
2
DC Output
OK (green)
On
Operating condition
3
O/T (yellow)
Off
Normal temperature
On
High temperature
Power Supply Unit Draco tera 80/48
1
Front View
Pos. LED
1
DC Input
OK (green)
DC Input
(red)
Status
Description
On
Operating condition
Off
No power supply
On
Power supply unit not active, Matrix is
powered by second power supply unit
Off
Operating condition
Pos: 23 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
25
Draco tera
Pos: 24 /806-IHSE/Beschreibung/Status/Port-Status/480-xx @ 7\mod_1309935423961_6.doc @ 52661 @ 3 @ 1
3.7.2
Port Status
The connections and the switching status between the various consoles
and CPUs are shown in this menu.
You have the following possibilities to access the menu:
Java Tool
The current port configuration of the Draco tera is illustrated in this menu.
 Select Status > Matrix View in the task area when connected to the
matrix.
Menu Status – Matrix View (example #1)
26
2013-08-14
Description
Menu Status – Matrix View (example #2)
The colors indicate the connection status:
Color
Description
Grey
Port not connected
Yellow
Video connection
Green
KVM connection
Red
Faulty Port
2013-08-14
27
Draco tera
The symbol indicates the extender that is recognized and defined at a
certain port:
Symbol
Description
Port connected to a CPU Unit
Port is connected to a CPU Unit that is switched to a
CON Unit in Private Mode (see Chapter 3.7.3, Page
30).
Port connected to a CON Unit
Port connected to a CON Unit with Shared Access to
a CPU.
Port is connected to a CON Unit that is connected to
a CPU Unit in Private Mode (see Chapter 3.7.3,
Page 30).
Port connected to an USB 2.0 CPU Unit
Port connected to an USB 2.0 CON Unit
Port is configured as a CON port for customer specific
applications
Port is configured as a CPU port for customer specifiv
applications




Red framed ports are defined as "fixed" (e. g. for USB 2.0
connections).
The port with four static blue squares is currently selected.
If a port is selected, all the other ports will be shown transparently,
except of those that are connected to the currently selected port. A
selection can be cleared by pressing the button Clear Selection.
If there is shown a red cross on a port when switching via Matrix
View, the console to be connected does not have access rights to the
respecting CPU at this port.
 In order to show the extender information of the currently selected
port in the right part of the working area, press the left mouse button.
28
2013-08-14
Description
The following information is available:
Field
Description
Extender Name Name of the selected extenders
Extender Type
Type of the selected extender
Port ID
Number of the selected port
Device Name
Name of the connected console or CPU
Connections
Listing of assigned connections to the marked port
(Full Access or Video Access)
 In order to open the context menu for the currently selected port with
further functions, press the right mouse button.
The following context functions are available:
Function
Description
Open Extender
The menu for definition of the currently selected
extender will be opened
Open Device
The menu for definition of the currently selected
console or CPU will be opened
Switch
The menu for execution of switching operations will
be opened
In order to reload the Matrix View you have the following possibilities:

Press the key <F5> on a connected keyboard

Execute Edit > Reload in the menu bar

Press the Button Reload in the tool bar
Pos: 25 /806-IHSE/Beschreibung/Status/Extender-OSD/480-xx @ 7\mod_1317829749536_6.doc @ 54621 @ 3 @ 1
2013-08-14
29
Draco tera
3.7.3
Extender OSD
All extenders used with the Draco tera are provided with their own OSD to
display the connection status of the own console.
Example View Extender OSD
The following information is shown in the OSD menu:
Field
Description
CON
Name of the own console
CPU
Name of the currently connected CPU
ACCESS




SHARED
30
Full Access: The own console has a KVM
connection to the displayed CPU.
Video Access: The own console has a video
only connection to the displayed CPU.
Private Mode: The own console has a
Private Mode connection to the displayed
CPU.
not connected: The own console is not
connected to a CPU.
x device(s) shows the exact number of devices
that also have a connection to the current CPU of
the own console (e.g. 3 devices).
If the field remains empty, there only exists the own
connection to the current CPU.
2013-08-14
Description
If the options Mouse Connect or Keyboard Connect (see Chapter 5.4.4,
Page 86) are used, the name of the console with keyboard / mouse
control will be displayed at those consoles that do not have K/M control at
the moment. The console is displayed in yellow color under Access.
Pos: 26 /806-IHSE/Beschreibung/Status/Netzwerk-Status/480-xx @ 7\mod_1309935505711_6.doc @ 52680 @ 3 @ 1
3.7.4
Network Status
The current network configuration is shown in this menu.
You have the following possibilities to access the menu:
The following information is shown in this menu:
Field
Description
DHCP
Information, if the network settings are applied
dynamically. Display Y (Yes) or N (No)
IP Address
Information about the IP address as provided
manually or via DHCP
Subnet Mask
Information about the subnet mask as provided
manually or via DHCP
Gateway
Information about the gateway address as provided
manually or via DHCP
MAC ID
Information about the MAC address of the matrix
2013-08-14
31
Draco tera
OSD
 Select Status > Network in the main menu.
Menu Status – Network
32
2013-08-14
Description
Java Tool
1.
Select Status > Matrix View in the task area.
Menu Status – Matrix View
2.
Use the left mouse button to click on the network port of the CPU
board.
The corresponding network status will be shown in the right part of
the working area.
Pos: 27 /806-IHSE/Beschreibung/Status/Firmware-Status/480-xx @ 7\mod_1309935560836_6.doc @ 52699 @ 33 @ 1
2013-08-14
33
Draco tera
3.7.5
Firmware Status Matrix
The current firmware status of the installed boards is shown in this menu.
You have the following possibilities to access the menu:
The following information is shown in this menu:
Field
Description
Name
Description of the modules
Type
Type number
Ports
Number of ports
Version
Complete description of the firmware version
Date
Date of the firmware version
Status
Module status
OSD
 Select Status > Firmware in the main menu.
Menu Status – Firmware
34
2013-08-14
Description
Java Tool
1.
Select Status > Matrix Firmware in the task area.
Menu Status – Matrix Firmware
2.
In order to read out the firmware status and store it locally (file
extension .dtf), select Matrix > Save Firmware Status to File....
3.
In order to read out the overall status of the matrix and store it locally
(file extension .zip), select Matrix > Save Status to File... or press
the respective button in the symbol bar.
The various modules can expanded and retracted in the column Name by
clicking with the left mouse button on the plus or minus symbols.
By clicking on the plus resp. minus symbol in the upper right corner of the
working area you can expand and retract all module information with one
click on the left mouse button.
2013-08-14
35
Draco tera
3.7.6
Firmware Status Extender
The current firmware status of the connected extenders is shown in this
menu.
You have the following possibility to access the menu:
The following information is shown in this menu:
Field
Description
Name
Description of the firmware
Type
Description of the extender module
Ports
Number of ports
Cur. Version
Description of the current firmware version
Cur. Date
Date of the current firmware version
 Select Status > EXT Firmware in the task area.
Menu Status – EXT Firmware
Pos: 28 /806-IHSE/Beschreibung/Funktion Trace/480-xx @ 7\mod_1309935652618_6.doc @ 52718 @ 2 @ 1
36
2013-08-14
Description
3.8
Trace Function
All events, e.g. activities and switching operations of the Draco tera matrix,
are logged and displayed in this menu.
This function is used for diagnostic purposes.
You have the possibility to request various trace views in the menu:
The following information is shown in this menu:
Field
Description
Date
Date stamp
Time
Time stamp
Message
Detailed description of the event
Trace possibilities
 Select Status > Trace IO Board in the main menu to check the
events on your current I/O board.
 Select Status > Trace Matrix to check the matrix events.
Pos: 29 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
37
Draco tera
Pos: 30 /806-IHSE/Beschreibung/Syslog Monitoring/480-xx @ 8\mod_1351496895799_6.doc @ 69482 @ 2 @ 1
3.9
Syslog Monitoring
The complete logging of the Draco tera matrix regarding activities,
switching operations and the surveillance of function critical components
like fans or power supply units take place in this menu.
You have the following possibility to access the menu:
In order to start Syslog Monitoring proceed as follows:
 Select the symbol Monitoring in the symbol bar.
Menu Monitoring – Syslog
The logging of system activities starts when opening the menu
Monitoring and remains active until the appropriate tab will be closed.
Syslog messages are transmitted via UDP. Therefore, port 514 within the
used network should not be blocked, e.g. by a firewall.
During logging the activities are written continuously into logging files and
stored locally. This process can be set with various options.
38
2013-08-14
Description
Options
 Select Extras > Options in the menu bar and open the tab Syslog.
The following options are available:
Option
Description
Log File Directory
Default directory to store the log files
Log File Name
Default name of the log file
Log File Extension
Default extension for the log file
Maximum Log File
Size (KB)
Allowed maximum size of log file
Maximum Number
of Log Files
Allowed maximum number of log files
When reaching the maximum log file size, a new log file will be created.
When reaching the maximum number of log files, the oldest one will be
overwritten with the new information.
Filter Function
In order to filter relevant messages out of a number of logged activities of
the Draco tera, the Syslog Monitoring offers various filter options.
In order to set and activate a filter, proceed as follows:
1.
Set the desired filter option(s) by activating the respective
checkbox(es).
2.
Activate the filter settings by pressing the button Filter.
3.
In order to deactivate an activated filter setting press the button Clear.
The following filter options are available:
Option
Description
Date
Messages of a defined date range will be filtered
Facility
Messages of a defined facility will be filtered
Severity
Messages of a defined severity will be filtered
Host
Messages of a defined host will be filtered
Message
Messages with defined text parts will be filtered
Filter options are not valid within the locally stored log files.
2013-08-14
39
Draco tera
Recording Function
All messages shown in the Syslog are equipped with various recording
functions.
 In order to store the messages shown in the Syslog (filtered or
unfiltered), press the button Save trace. The messages will be stored
in a .txt file.
 In order to remove the messages shown in the Syslog, press the
button Clear trace.
 In order to stop recording the messages, press the button Pause. In
order to continue press the button again.
Pos: 31 /806-IHSE/Beschreibung/SNMP/480-xx @ 8\mod_1352794857131_6.doc @ 69602 @ 2 @ 1
3.10
SNMP
When using the SNMP function all function critical and safety critical parts
of the matrix can be monitored and their status can be queried. This
function complies with a RFC 1157 conformal standard.
When using SNMP monitoring, a dedicated network for reasons of access
security is strongly recommended.
You have the following possibilities to configure the SNMP monitoring:
40
2013-08-14
Description
OSD
In order to activate the SNMP agent, proceed as follows:
1.
Select Configuration > SNMP in the main menu.
Menu Configuration – SNMP
2.
Set the option Enable to Y (Yes) under SNMP Agent. By activating
this option, the permission for an active query of the SNMP agent is
granted.
In order to configure a SNMP server, proceed as follows:
1.
Select Configuration > SNMP in the main menu.
2.
Set the option Enable Traps to Y (Yes) within SNMP Server. This
function allows an active transmission of trap messages from the
SNMP agent to the SNMP server.
3.
Set the IP address of the SNMP server within Server Address.
4.
Activate the requested traps by enabling them to Y (Yes).
2013-08-14
41
Draco tera
You can select between the following traps:
Trap
Description
Status
Notification about the matrix status
Temperature
Notification about the temperature within the matrix
Insert Board
Notification about the insertion of a new I/O board
into a slot
Remove Board
Notification about the removal of an I/O board out of
a slot
Invalid Board
Notification about a non-properly working I/O board
Insert Extender
Notification about a newly connected extender to
the matrix, notification about a switched on
extender, notification about a newly established link
between extender and matrix
Remove Extender
Notification about a removed extender from the
matrix, notification about a switched off extender,
notification about an interrupted link between
extender and matrix
Switch Command
Notification about a performed switching operation
at the matrix
Fan Tray #1
Notification about the status of fan tray #1
Fan Tray #2
Notification about the status of fan tray #2
Power Supply #1
Notification about the status of power supply unit #1
Power Supply #2
Notification about the status of power supply unit #2
Power Supply #3
Notification about the status of power supply unit #3
For an activation of the SNMP agent function or the SNMP server
function, a restart of the matrix is obligatory.
42
2013-08-14
Description
Java Tool
In order to activate the SNMP agent, proceed as follows:
1.
Select System > Network in the task area.
Menu System – Network
2.
Activate the option SNMP Agent in the tab SNMP. By activating this
option, the permission for an active query of the SNMP agent is
granted.
In order to configure a SNMP-Server, proceed as follows:
1.
Select Configuration > Network in the task area.
2.
Activate the option Enable Traps within SNMP Server. This function
allows an active transmission of trap messages from the SNMP agent
to the SNMP server.
3.
Set the IP address of the SNMP within SNMP Server.
4.
Activate the requested traps.
For an activation of the SNMP agent function or the SNMP server
function, a restart of the matrix is required.
Pos: 32 /806-IHSE/Beschreibung/System Check/480_xx @ 9\mod_1375105102198_6.doc @ 78732 @ 2 @ 1
2013-08-14
43
Draco tera
3.11
System Check
The System Check offers a diagnostic function for checking your current
matrix configuration. The purpose of this feature is to find suboptimal and
faulty settings and to point these out.
The System Check is exclusively used for a plausibility check and does
not make any active changes in the configuration.
You have the following possibility to access the menu:
The following configuration parts are checked:

Matrix Firmware

Extender Firmware

Multi-Screen Control

Ext Units

CPU Devices

CON Devices

User

System Configuration
The following notification levels can be shown:
Level
Description
OK (green)
System Check completed without any
abnormalities
WARNING (yellow)
System Check revealed abnormalities in the
configuration that point out to incomplete parts of
the configuration, firmware differences,
duplications or not connected extenders but
without being system critical
ERROR (red)
System Check revealed errors in the configuration
that can have both functional and system critical
influences on the system.
If the messages "WARNING" and "ERROR" are created by the System
Check function, the respective problem will be described and a basic
guideline will be provided.
44
2013-08-14
Description
In order to start System Check, proceed as follows:
 Select the symbol System Check in the symbol bar.
Menu – System Check
Pos: 33 /806-IHSE/Installation/UEB_Installation @ 5\mod_1278574971589_6.doc @ 41768 @ 1 @ 1
2013-08-14
45
Draco tera
4
Installation
Pos: 34 /806-IHSE/Installation/Lieferumfang prüfen/480-xx @ 7\mod_1309935842774_6.doc @ 52736 @ 2 @ 1
4.1
Package Contents
Your package contains the following items:

Draco tera matrix

1x power cord per built-in power supply unit

1x serial control cable

Mounting accessories

Quick Setup

Java Tool

1x Cat X network cable (cross-wired)
If anything is missing, contact your dealer.
Pos: 35 /806-IHSE/Installation/System anschließen/480-xx @ 7\mod_1309935998118_6.doc @ 52754 @ 2 @ 1
4.2
System Setup
First time users are recommended to setup the system in the same room
as a test setup. This will allow you to identify and solve any cabling
problems, and experiment with your system more conveniently.
Setup of the matrix
1.
Install the CPU and I/O boards.
2.
Connect keyboard, mouse and monitor to the CPU board of the
matrix.
3.
Connect the matrix to the power supply.
4.
Open OSD via 'Hot Key' and login with administrator rights in the
main menu under configuration (see Chapter 5.2.1, Page 55).
5.
Configure initially as requested.
After the configuration of the system it is recommended to save the
configuration by selecting Configuration > Save and restart the matrix by
selecting Restart Matrix.
6.
46
Optional: Establish a network connection between the matrix and the
Java tool in order to set an extended configuration (see Chapter
5.2.2, Page 60).
2013-08-14
Installation
Setup of Extender
1.
Connect the CON units to the matrix by using the interconnect cables
(Cat X or fiber).
2.
Connect the CON units to the input devices that has to be used (for
example keyboard and mouse).
3.
Connect the 5VDC power supply units to the CON units.
4.
Check the basic function of the CON unit by opening the OSD via
'Hot Key'.
5.
Connect the source (computer, CPU) to the CPU unit of the extender
by using the provided connection cables.
6.
Connect the CPU unit to the matrix by using the interconnect cables
(Cat X or fiber).
7.
If you have a video matrix, connect the video source directly to the
matrix by using the interconnect cables (coax, fiber).
8.
Connect the 5VDC power supply units to the CPU units.
9.
Start the system.
Pos: 36 /806-IHSE/Installation/Installationsbeispiele/UEB_Installationsbeispiele_480-xx @ 7\mod_1311338893738_6.doc @ 54459 @ 2 @ 1
4.3
Example Applications
The Draco tera supports a most flexible configuration of your system
environment:
Pos: 37 /806-IHSE/Installation/Installationsbeispiele/480-xx/Installationsbeispiele @ 7\mod_1309936170836_6.doc @ 52791 @ @ 1
A part of the Draco tera can be configured as a Single-Head work station,
a part as Dual-Head, as Quad-Head or even as a video matrix for
example. In addition to that there are configurations with KVM and
USB 2.0 available.
Among the access via OSD by the keyboard connected to the CPU board
or an extender CON unit, you have the following additional access
options:

via Java Tool

via serial interface
A connection to common media controls is possible, too.
The following part shows typical exemplary installations of the Draco tera:
Pos: 38 /806-IHSE/Installation/Installationsbeispiele/480-xx/KVM-Matrix @ 7\mod_1309936183571_6.doc @ 52810 @ 3 @ 1
2013-08-14
47
Draco tera
4.3.1
KVM Matrix
In Single-Head mode, up to 288 ports can be used either as an input or as
an output port depending on components and equipment. At the same
time there is a non blocking access for all users, i.e. user access is not
limited by the activities of another user.
1
2
3
4
3
5
6
Single-Head KVM Matrix
1
Source (computer, CPU)
2
CPU unit
3
Interconnect cable
4
Draco tera matrix
5
CON unit
6
Console (monitor, keyboard, mouse)
If you have a Single-Head console, you can also get access to a DualHead or Quad-Head CPU for example. However control is only possible at
monitor 1.
Any signal source can be switched to any number of monitors that will
show the video signal at the same time. In addition to that even (optional)
audio can be switched.
Pos: 39 /806-IHSE/Installation/Installationsbeispiele/480-xx/Videomatrix @ 7\mod_1309936380821_6.doc @ 52828 @ 3 @ 1
48
2013-08-14
Installation
4.3.2
Video Matrix
If you use the Draco tera as a video matrix, up to 288 input ports can be
switched to up to 288 output ports depending on components and
equipment.
1
2
3
2
4
Video Matrix
1
Video source (e. g. SDI camera)
2
Interconnect cable
3
Draco tera matrix
4
Video sink (e. g. monitor)
Pos: 40 /806-IHSE/Installation/Installationsbeispiele/480-xx/Parallelbetrieb (Stacking) @ 7\mod_1309936438040_6.doc @ 52846 @ 3 @ 1
2013-08-14
49
Draco tera
4.3.3
Parallel Operation (Stacking)
If you have special configurations, especially at installations with several
monitors per work station or additional support of USB 2.0 transmission
paths, the number of connectable CPUs and consoles can be increased
by a parallel operation (stacking) of several Draco tera devices.
One of the Draco tera matrices has to be defined as the master matrix,
all the others have to be configured as slave matrix and the IP address of
the master matrix has to be entered in the field Master IP Address (see
Chapter 5.4.1, Page 75). They have to be connected to the master matrix
via network connector (RJ45) of the CPU board. The option Enable LAN
Echo has to be activated at the master matrix (see Chapter 5.4.1, Page
75).
If a switching command is done in the OSD, the slave matrices will also
switch automatically.
Switching of stacked devices might be delayed by several seconds.
1
2
3
4
5
6
3
7
8
Parallel Operation (Stacking)
50
2013-08-14
Installation
1
Dual-Head source (computer, CPU)
2
CPU unit
3
Interconnect cable
4
Draco tera matrix (master matrix)
5
Draco tera matrix (slave matrix)
6
Network connection master / slave(s)
7
CON unit
8
Console (2x monitor, keyboard, mouse)
Pos: 41 /806-IHSE/Installation/Installationsbeispiele/480-xx/Kaskadierung @ 7\mod_1309936471961_6.doc @ 52864 @ 3 @ 1
2013-08-14
51
Draco tera
4.3.4
Cascading
For applications exceeding the number of available ports, the system can
be extended by cascading.
In this case, the Draco tera devices are connected by so-called "tie lines".
The tie lines are dynamically configured to support connections in both
directions.
To access cascaded matrices from a console, one of the matrices has to
be configured as sub matrix (see Chapter 5.4.1, Page 75).
1
2
3
4
3
5
3
6
7
Cascading
1
Source (computer, CPU)
2
CPU unit
3
Interconnect cable
4
Draco tera (sub matrix)
5
Draco tera (main matrix)
6
CON unit
7
Console (monitor, keyboard, mouse)
Pos: 42 /806-IHSE/Konfiguration/UEB_Konfiguration @ 5\mod_1278575517073_6.doc @ 41846 @ 1 @ 1
52
2013-08-14
Configuration
5
Configuration
Pos: 43 /806-IHSE/Konfiguration/Kommando-Modus/480-xx @ 7\mod_1309936855602_6.doc @ 52882 @ 2 @ 1
5.1
Command Mode
The Draco tera has a Command Mode that allows several functions via
keyboard command during normal use.
To enter Command Mode use a 'Hot Key' sequence and to exit Command
Mode, press <Esc>. While in Command Mode, the LEDs Shift and Scroll
on the console keyboard will flash.
In Command Mode normal keyboard and mouse operation will cease.
Only selected keyboard commands are available.
If there is no keyboard command executed within 10 s after activating
Command Mode, it will automatically be deactivated.
The following table lists the keyboard commands to enter and to exit
Command Mode and to change the 'Hot Key' sequence:
Function
Keyboard Command
Enter Command Mode (default)
2x <Left Shift> (or 'Hot Key')
Exit Command Mode
<Esc>
Change 'Hot Key' sequence
<current 'Hot Key'>, <c>,
<new 'Hot Key' code>, <Enter>
Until 2011-30-09:
<Left Ctrl> + <Left Shift> + <c>,
<'Hot Key' Code>, <Enter>
<Key> + <Key>
<Key>, <Key>
2x <Key>
2013-08-14
Press keys simultaneously
Press keys successively
Press key quickly, twice in a row
(similar to a mouse double-click)
53
Draco tera
The 'Hot Key' sequence to enter Command Mode can be changed. The
following table lists the 'Hot Key' Codes for the available key sequences:
'Hot Key' Code
'Hot Key'
0
Freely selectable (from 2012-01-12 on)
2
2x <Scroll>
3
2x <Left Shift>
4
2x <Left Ctrl>
5
2x <Left Alt>
6
2x <Right Shift>
7
2x <Right Ctrl>
8
2x <Right Alt>
In a combined KVM matrix / U-Switch configuration, choose different 'Hot
Keys' for the KVM matrix and the U-Switch.
Set freely selectable 'Hot Key' (exemplary)
In order to set a freely selectable 'Hot Key' (e.g. 2x <Space>), use the
following keyboard sequence:
<current 'Hot Key'>, <c>, <0>, <Space>, <Enter>
Set 'Hot Key' for direct OSD Access
When setting a second 'Hot Key', next to the 'Hot Key' for standard
functions, this 'Hot Key' can be exclusively used for opening the OSD
directly.
In order to select a 'Hot Key' from the 'Hot Key' table for opening OSD
directly, use the following keyboard sequence:
<current 'Hot Key'>, <f>, <'Hot Key' code>, <Enter>
In order to select a freely selectable 'Hot Key' (e.g. 2x <Space>) for
opening OSD directly, use the following keyboard sequence:
<current 'Hot Key'>, <f>, <0>, <Space>, <Enter>
Reset 'Hot Key'
In order to set a 'Hot Key' back to default settings of the extender, press
the key combination <Right Shift> + <Del> within 5 s after switching on the
CON unit or plugging in a keyboard.
Pos: 44 /806-IHSE/Konfiguration/480_Ansteuerung/480-xx/Ansteuerungsoptionen @ 7\mod_1309936958868_6.doc @ 52902 @ 2 @ 1
54
2013-08-14
Configuration
5.2
Control Options
The Draco tera contains an internal CPU that allows you to control all
functions from any console without the need for an external CPU or media
control.
You have the following possibilities to access the Draco tera for
configuration and operation:

via OSD

via Java Tool

via serial interface
Pos: 45 /806-IHSE/Konfiguration/480_Ansteuerung/480-xx/Ansteuerung via OSD @ 7\mod_1309937635540_6.doc @ 52920 @ 3 @ 1
5.2.1
Control via OSD
Via OSD (On-Screen-Display) you set the configuration of the Draco tera
operating system. The settings of the menu Configuration are described
below. All other menus are described in later chapters.
You have the following possibilities to enter the OSD of the Draco tera:

via keyboard connected to the CPU board

via keyboard connected to a CON unit of an extender
Entering OSD
1.
Start Command Mode with the 'Hot Key' (see Chapter 5.1, Page 53).
2.
Press <o> to open OSD.
You will see a list of all available CPUs as a start menu.
3.
Press <Esc> to enter the main menu.
If the option Enable CPU Selection is activated in the menu
Configuration, first of all the selection list for switching CPU devices will
be opened. This list can be skipped by pressing the key <F7>.
Leaving OSD
 Press the key <Esc> in the main menu or simultaneously <Left Shift>
+ <Esc> anywhere within the OSD.
The OSD will be closed without any further changes and the currently
active CPU connection will be displayed.
2013-08-14
55
Draco tera
Menu Structure
Example View
The general layout of the OSD is structured into three areas:
56

Upper status area (topmost two text lines)

Working area

Lower status area (lowest two text lines)
2013-08-14
Configuration
Keyboard control
You can select between the following keyboard commands:
Function
Keyboard Command
Left cursor - only within an input field or a
switching screen
<Cursor Left>
Right Cursor - only within an input field or a <Cursor Right>
switching screen




In input fields: Line up (with wrap
around)
In menus: Line up (without wrap
around)
<Cursor Up>
In input fields: Line down (with wrap
around)
In menus: Line down (without wrap
around)
<Cursor Down>
Previous page in menus with more than
one page
<Page Up>
Next page in menus with more than one
page
<Page Down>
Next input field
<Tab>
Previous input field
<Left Shift> + <Tab>
Next option in selection fields
<+>
Previous option in selection fields
<->
Switching in selection fields between two
conditions, e. g. between ON / OFF or Y
(Yes) / N (No)
<Space>


In menus with input fields: Save data
In menus: Select menu item

In menus with input fields: Cancel data <Esc>
input without saving
In menus with selection fields: Go
back to the superior menu

2013-08-14
<Enter>
57
Draco tera
Sorting Function
Lists and tables in the Java Tool offer a sorting function for fast and
smooth search.
You have the possibility to use the following sorting functions:
58
Function
Keyboard Command
Sort ID numbers in a descending order or
in an ascending order by pressing the
keyboard command twice (ID).
<F1>
Sort ID names in a descending order or in
an ascending order by pressing the
keyboard command twice (Name).
<F2>
Go to the next result in the list of results of
the search field (Next).
<F3>
Go to the previous result in the list of
results of the search field (Previous).
<F4>
Refresh the currently shown list (Refresh).
<F5>
Jump between the search field and the list
of results (Find).
<F6>
2013-08-14
Configuration
Password request
You have to login with administrator rights to be able to set configurations.
Menu Login
Access to the configuration menu requires administrator rights. User login
is mandatory.
Field
Input
User
admin
Password
admin
By pressing the key <F10> in the main menu of the OSD, the login mask
will be opened. In order to log out a user, press the key <F10> again.
For security reasons, please change the administrator password as soon
as possible (see Chapter 5.4.1, Page 75).
Pos: 46 /806-IHSE/Konfiguration/480_Ansteuerung/480-xx/Ansteuerung via Java-Tool @ 7\mod_1309937697743_6.doc @ 52938 @ 3 @ 1
2013-08-14
59
Draco tera
5.2.2
Control via Java Tool
Requirements
If you want to use the Java Tool, the following requirements have to be
fulfilled:

Computer with an executable Java Tool and an installed Java
Runtime Environment (JRE, version 1.6 or higher)

Java Tool software

Available network connection between the Java Tool and the matrix
Contact your system administrator concerning JRE and network
connection.
Installation of the Java Tool
The Java Tool is available as a single executable program file that does
not require a separate installation.
 Copy the tool after receiving the file to a directory on your computer.
If you do not have a Java Tool, contact your dealer.
Computer Connection to the Matrix
For a direct connection between computer and matrix, a cross-wired
network cable is required.
For a connection between computer and matrix via switch or hub, a
parallel assembled network cable is required.
Do not use a network connection between Java Toll and the matrix that is
primarily used for transmitting audio data.
 Connect the network cable to the RJ45 ports of computer and CPU
board of the matrix.
Start of the Java Tool
 Open the Java Tool by a double click on the program icon or use the
<Enter> key of the keyboard.
60
2013-08-14
Configuration
Connection to the Matrix
At least FTP rights are required.
1.
Open the Java Tool.
2.
Select Matrix > Connect in the menu bar.
3.
Enter the IP address in the popup input field according to the network
configuration of the Draco tera (see Chapter 5.2.3, Page 69).
4.
Enter the user name and password for the Draco tera (see Chapter
5.4.1, Page 75).
5.
Confirm your inputs with the button OK or reject with Cancel.
Menu Connect
Up to twelve connections between the matrix and the Java tool can be
established at the same time due to a limitation of available sockets.
2013-08-14
61
Draco tera
Menu structure
Example View (System – System Data)
The menu structure of the Java Tools is subdivided into various sections:

Menu bar (top line)

Toolbar (second line)

Tab bar (third line)

Task area (left menu section)

Working area (right menu section)

Status bar (bottom line section)
Operating Instructions
The operation of the Java Tool is intuitive and corresponds to the user
interface of common operating systems.
The Java Tool contains its own support function.
The integrated help texts in the working area of the Java Tool can be
activated or deactivated by the checkbox in the upper right corner.
62
2013-08-14
Configuration
Mouse Control
You can select between the following mouse commands:
Function
Mouse Command
Menu selection, marking
Left mouse button
Open function specific selection menus
Double click left mouse
button
Open context specific selection menus
Right mouse button
Keyboard Control
You can select between the following keyboard commands:
Function
Keyboard Command
Cursor to the left
<Cursor Left>
Cursor to the right
<Cursor Right>
Line up
<Cursor Up>
Line down
<Cursor Down>
Previous page in input or status menus
with more than one page
<Page Up>
Next page in input or status menus with
more than one page
<Page Down>
Next field in input menus
<Tab>
Previous field in input menus
<Left Shift> + <Tab>


Switching in selection fields between <Space>
two conditions (checkmark or not).
Open already marked fields with
editing or selecting possibility.


In menus: Data saving
Menu item selection
<Enter>


Leave tables
Jump from tables into the next field
<Ctrl> + <Tab>


Leave tables
Jump from tables into the previous
field
<Ctrl> + <Left Shift> +
<Tab>
Various functions within the menus in the menu bar can be executed with
the provided keyboard commands (e. g. press <Ctrl> + <S> to execute
Save) that are listed to the right of the respective menu item.
2013-08-14
63
Draco tera
Reload Options
The information shown in the Java Tool can be reloaded in different ways.

Via <F5> key on the used keyboard

Via Edit > Reload in the menu bar

Via "Reload"-Symbol in the symbol bar
Context Function
The Java Tool offers several context functions that support a user friendly
and effective operation of the tool. The context functions are described in
the respective chapters.
 In order to execute a context function, use the right mouse button on
the corresponding field and select the desired function.
Sorting Function
Lists and tables in the Java Tool offer a sorting function for fast and
smooth search.
1.
For ascending sort status, use the left mouse button once to click into
the header of the column to be sorted.
The sort status is indicated by an arrow that points upwards.
64
2.
For descending sort, use the left mouse button twice to click on the
header of the column that has to be sorted. The sort is displayed by
an arrow that points downwards.
3.
In order to cancel the sort, use the left mouse button once or twice to
click on the header of the column that is sorted until the displayed
arrow will disappear.
2013-08-14
Configuration
Filter Function
Lists and tables in the Java Tool offer a filter function that allows a fast
and smooth search inside.
1.
In order to activate a filter, use the right mouse button to click on the
header of the column that has to be filtered and select Set Filter.
2.
Write directly the word or part of a word that has to be filtered into the
header.
The filter results are shown immediately.
3.
In order to delete a filter, use the right mouse button to click on the
header of the column that has to be filtered and select Clear Filter.
An active filter is indicated by an asterix in the header.
The filter function is based on the functional principle of common web
search engines.
Offline Configuration
Configuration and system settings via Java Tool can be changed in offline
mode without a direct connection between matrix and Java Tool.
In order to activate a configuration in the matrix, proceed as follows:
1.
Select File > Upload in the menu bar.
2.
Enter the IP address of the matrix (see Chapter 5.2.3, Page 69) and
the name and password of the user authorization and select the
storage location of the new configuration (default or config01-08) in
the menu Select Configuration.
3.
Select Matrix > Connect in the menu bar and enter the IP address of
the matrix and the name and password for user authorization.
4.
Select Administration > Activate Configuration in the task area
and select the storage location that has been selected above.
5.
Use the button Activate to open the selected configuration within the
matrix.
The connection and the open tab will be closed and the matrix will be
restarted.
During the activation of a configuration, the matrix is temporarily not
available.
2013-08-14
65
Draco tera
Online Configuration
Configurations and system settings can be also edited via Java tool in
online mode with an active connection between matrix and Java tool.
Menu System – System Data
In order to edit a configuration in online mode, proceed as follows:
66
1.
Select the menu item Matrix > Activate Online Configuration
Mode. This setting will be additionally shown in the lower part of the
working area.
2.
Make any edits at the configuration and system settings and confirm
them by pressing the button Apply. The changes will be immediately
applied.
3.
In order to deactivate the online mode, select the menu item Matrix >
Deactivate Online Configuration Mode in the menu bar.
2013-08-14
Configuration
Options menu
The use of the Java tool can be adapted and customised by editing
various default settings.
In order to activate or change the default settings , proceed as follows:
 Select Extras > Options in the menu bar. The tab Default Settings
will open.
The following default settings parameters can be done:
Option
Description
IP / Hostname
Default IP address of the matrix required for
connection
User
Default user name required for connection
Configuration
Directory
Default directory for configuration files
Firmware
Directory
Default directory for update files
Status
Directory
Default directory for the firmware status
Import / Export
Directory
Default directory for import and export files
Presets
Directory
Default directory for macro files
In order to set various font sizes for the Java tool, proceed as follows:
1.
Select Extras > Options in the menu bar.
2.
Open the tab Font.
3.
Select the desired font size (normal or large).
2013-08-14
67
Draco tera
Report
The Java tool is equipped with a report function that shows the current
switching status and all relevant parts of the matrix configuration in a PDF
file.
In order to create a report, proceed as follows:
1.
Select File > Report... in the menu bar. A selection assistant will be
opened.
2.
Select those contents that should be included in the report (Matrix
View, EXT Units, CPU Devices, CON Devices and Users) and
confirm with the button Next >.
3.
Select the preferred location for storage of the report and confirm with
the button Finish.
The report will be created as a PDF file.
Menu File > Report
The report function can be used in both online or offline mode of the Java
tool.
Pos: 47 /806-IHSE/Konfiguration/480_Ansteuerung/480-xx/Ansteuerung via serieller Schnittstelle @ 7\mod_1309937747180_6.doc @ 52956 @ 3 @ 1
68
2013-08-14
Configuration
5.2.3
Control via Serial Interface
The Draco tera operating system offers various functions for an operation
via serial interface. There are telegrams for Switching single or all
connections available, both unidirectional and bidirectional. In addition to
that, there are telegrams for an overall definition of the total switching
status and for saving and loading such switching states.
By request, the Draco tera optionally provides an echo of all effected
switching operations via serial interface or network interface. That is why
you have the possibility to track the current configurations of the matrix at
any time and so update your own applications.
As an additional application you can switch parallely Draco tera clones as
slaves (Stacking) via serial network interface.
Pos: 48 /806-IHSE/Konfiguration/480_Zuordnung/480-xx/Zuordnung @ 7\mod_1309937797383_6.doc @ 52976 @ 2 @ 1
5.3
Assignment
The Draco tera offers the possibility of a console specific or a CPU
specific assignment.

The first possibility is to assign virtual CPUs to real CPUs.

The second possibility is to assign real consoles to virtual consoles.
Pos: 49 /806-IHSE/Konfiguration/480_Zuordnung/480-xx/Virtuelle CPU @ 7\mod_1309937891305_6.doc @ 53012 @ 3 @ 1
5.3.1
Virtual CPU
You can assign virtual to real CPUs in this menu.
With this function the effort for switching several consoles to the same
CPU can be reduced. If there a several consoles connected to a virtual
CPU that is assigned to a real CPU, you will only have to change the real
CPU once and all consoles will receive the video signal of the new CPU.
You have the following possibilities to access the menu:
2013-08-14
69
Draco tera
OSD
 Select Assignments > Virtual CPU Devices in the main menu.
Menu Assignments – Virtual CPU Devices
For an assignment, proceed as follows:
1.
Select the virtual CPU in the list Virtual Devices that has to be
assigned to a real CPU.
2.
Press the button Edit.
3.
Select the CPU in the list Real Devices that has to be assigned to the
selected virtual CPU.
4.
Press the button Okay to confirm the assignment.
The assignment will be done.
Only one virtual CPU can be assigned to a real CPU.
70
2013-08-14
Configuration
Java Tool
 Select Assignment > Virtual CPU Devices in the task area.
Menu Assignment – Virtual CPU Devices
For an assignment, proceed as follows:
1.
Select a virtual CPU in the list Virtual CPU.
2.
Double click in the column Real CPU to get a list of all available real
CPUs.
3.
Select a real CPU.
You can select between the following buttons:
Button
Function
Send
Send assignments to the matrix
Reload
Reload changes
When activating the function Auto Send in the left lower corner of the
working area, switching operations will be done immediately without
confirmation by pressing the button Send.
2013-08-14
71
Draco tera
The selection boxes in the column Real CPU contain a filter function for
an easy selection of single consoles from a larger pool of consoles (see
Chapter 5.2.2, Page 60).
The Java tool additionally offers the possibility to go directly from the
menu Assignment to the menu Definition to check specific settings for
the respective console or CPU.
 Use the right mouse button to select the respective console or CPU
and select Open CON Device or Open CPU Device.
Pos: 50 /806-IHSE/Konfiguration/480_Zuordnung/480-xx/Virtuelle Konsole @ 7\mod_1309937842805_6.doc @ 52994 @ 3 @ 1
5.3.2
Virtual Console
You can assign real consoles to virtual consoles in this menu.
With this function the effort to set and change access permissions can be
reduced by changing the permissions of the virtual console and so
applying them to all assigned real consoles, too.
Virtual consoles can be switched exactly in the same way as real
consoles. If a virtual console is switched to a CPU, all real consoles that
are assigned to the virtual console will receive the video signal. The real
console that is lastly scheduled in the list of assignments will additionally
receive keyboard and mouse control.
You have the following possibilities to access the menu:
72
2013-08-14
Configuration
OSD
 Select Assignments > Virtual CON Devices in the main menu.
Menu Assignments – Virtual CON Devices
For an assignment, proceed as follows:
1.
Select the real console in the list Real Devices that has to be
assigned to a virtual CPU.
2.
Press the button Edit.
3.
Select the virtual console in the list Virtual Devices that has to be
assigned to the selected real console.
4.
Press the button Okay to confirm the assignment.
The assignment will be done.
A virtual console can be assigned to more than one real consoles.
2013-08-14
73
Draco tera
Java Tool
 Select Assignment > Virtual CON Devices in the task area.
Menu Assignment – Virtual CON Devices
In order to place an assignment, proceed as follows:
1.
Select the required real console in the table Real Console.
2.
Double click in the column Virtual Console to get a list of all available
virtual consoles.
3.
Select the required virtual console.
You can select between the following buttons:
Button
Function
Send
Send assignments to the matrix
Cancel
Reject changes
When activating the function Auto Send in the left lower corner of the
working area, switching operations will be done immediately without
confirmation by pressing the button Send.
The selection boxes in the column Virtual Console contain a filter
function for an easy selection of a single CPU from a larger pool of CPUs
(see Chapter 5.2.2, Page 60).
Pos: 51 /806-IHSE/Konfiguration/Systemeinstellung/480-xx/Systemeinstellungen @ 7\mod_1309937961274_6.doc @ 53032 @ 2 @ 1
74
2013-08-14
Configuration
5.4
System Settings
You have the possibility to configure the following system settings at the
Draco tera.
The configuration of the system settings can only be done by users with
administrator rights.
Pos: 52 /806-IHSE/Konfiguration/Systemeinstellung/480-xx/System Data @ 7\mod_1309938005493_6.doc @ 53050 @ 3 @ 1
5.4.1
System Data
The system configuration is set in this menu.
You have the following possibilities to access the menu:
You can select between the following settings:
Field
Selection
Description
Device
Text
Enter the device name of the matrix
(default: SWITCH_01)
Name
Text
Enter the name of the configuration that is
used to save the current settings
(default: Standard)
Info
Text
Additional text field to describe the
configuration (default: Factory settings)
Sub Matrix
activated
If the matrix is defined as a sub matrix in
the OSD, the user will loose control
automatically. Control can be recovered by
using the keyboard command <Shift>,
<Shift>, <s>, <o>. The OSD now will be
opened again in the matrix that has been
defined as sub matrix.
deactivated
Load Default activated
deactivated
2013-08-14
Function not active (default)
Starting the matrix after a restart or a
switch-on with the default configuration.
Starting the matrix after a restart or a
switch-on with the last saved configuration
(default).
75
Draco tera
Field
Selection
Description
Auto Save
activated
Save the current configuration of the matrix
in the flash memory periodically.
Note: During saving of the configuration,
the matrix will not be operational. Saving
takes place every 600 seconds, as long as
changes of the configuration or switching
operations have been executed in the
meantime.
deactivated
Function not active (default)
activated
Send all performed switching commands in
the matrix as an echo via serial interface.
Note: This function should be enabled
when using a media control via serial
interface.
Enable
COM Echo
Enable LAN
Echo
Slave Matrix
76
deactivated
Function not active (default)
activated
Send all performed switching commands in
the matrix as an echo via LAN connection.
Note: This function should be enabled
when using a media control via LAN
connection or when using stacking with two
ore more matrices.
deactivated
Function not active (default)
activated
Synchronize the slave matrix according to
the switch status of the master matrix.
deactivated
Function not active (default)
Master IP
Address
Numerical
value
Set the network address of the master
matrix (default value: 000.000.000.000)
Ivalid IOBoards
activated
Keep I/O boards with wrong or invalid
firmware online in the matrix.
deactivated
Shut down I/O boards with wrong or invalid
firmware automatically (default).
Hor. Mouse
Speed 1/x
1-9
Adjustment of the horizontal mouse speed,
1 = slow, 9 = fast (default value: 4)
Ver. Mouse
Speed 1/x
1-9
Adjustment of the vertical mouse speed,
1 = slow, 9 = fast (default value: 5)
Double Click 100-800
Time
Adjustment of the time slot for a double
click (default value: 200 ms)
Keyboard
layout
Set the OSD keyboard layout according to
the used keyboard (default: German (DE))
Region
2013-08-14
Configuration
OSD
 Select Configuration > System in the main menu.
Menu Configuration – System
You can select between the following buttons:
Button
Function
Cancel
Reject changes
Save
Save changes
2013-08-14
77
Draco tera
Java Tool
Menu System – System Data
Pos: 53 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
78
2013-08-14
Configuration
Pos: 54 /806-IHSE/Konfiguration/Systemeinstellung/480-xx/Automatic ID @ 7\mod_1309938041118_6.doc @ 53068 @ 3 @ 1
5.4.2
Automatic ID
The settings for the automatic creation of CPU and CON devices by
connecting a new extender unit are made in this menu.
You have the following possibilities to access the menu:
You can select between the following settings:
Field
Selection
Description
Enable Auto
Config
activated
Automatic creation of a new CPU or
CON device if new extender units are
connected (default)
deactivated Function not active
ID Real CPU
Device
Numerical
value
Initial value of the automatic ID for real
CPUs (default value: 1000)
ID Virtual CPU
Device
Numerical
value
Initial value of the automatic ID for virtual
CPUs (default value: 2000)
ID Real CON
Device
Numerical
value
Initial value of the automatic ID for real
CONs (default value: 3000)
ID Virtual CON
Device
Numerical
value
Initial value of the automatic ID for virtual
CONs (default value: 4000)
2013-08-14
79
Draco tera
OSD
 Select Configuration > System in the main menu.
Menu Configuration – System
You can select between the following buttons:
80
Button
Function
Cancel
Reject changes
Save
Save changes
2013-08-14
Configuration
Java Tool
 Select the tab Automatic ID in System > System Data.
Menu System – Automatic ID
Pos: 55 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
81
Draco tera
Pos: 56 /806-IHSE/Konfiguration/Systemeinstellung/480-xx/Zugang @ 7\mod_1309938080446_6.doc @ 53086 @ 3 @ 1
5.4.3
Access
The access configuration is set in this menu.
You have the following possibilities to access the menu:
You can select between the following settings:
Field
Selection
Force User activated
Login
Description
The user has to login with a user name and a
password once to enter OSD. Thereafter the
user remains logged in until he explicitly logs
out or an auto logout is effected.
Note: When using the function Force User
Login, console favorites and console macros
still remain active.
deactivated Function not active (default)
Enable
User ACL
activated
CPU access is restricted according to the
permissions in the ACL (Access Control List).

User login is required.

Switching by keyboard 'Hot Keys'
requires a prior login.
deactivated Function not active (default)
Enable
Console
ACL
activated
CPU access is restricted according to the
permissions in the respective Console ACL
(Access Control List). No login required
deactivated Function not active (default)
Enable
new User
activated
Newly created users automatically receive
access to all CPUs
deactivated Function not active (default)
Enable
new CON
activated
Newly created CON devices automatically
receive access to all CPUs
deactivated Function not active (default)
Auto
activated
Disconnect
Upon opening the OSD, the console will be
automatically disconnected from the current
CPU.
deactivated Function not active (default)
82
2013-08-14
Configuration
Field
Selection
Description
OSD
Timeout
0-999
seconds
Period of inactivity after which OSD will be
closed automatically.

Select 0 seconds for no timeout
(default: 0 seconds)
Auto
Logout
0-999
minutes
Period of inactivity of a logged-in user at a
console after which he will be automatically
logged out at this console.
There might be a disconnect because of the
logout, depending on the defined rights in
each CON and user ACL.

Select 0 minutes for an automatic user
logout when leaving OSD.
– Using the setting -1 allows the user
to be logged in permanently, until a
manual logout is executed.
The timer is not active as long as the
OSD is open.
(default: 0 minutes)

2013-08-14
83
Draco tera
OSD
 Select Configuration > Access in the main menu.
Menu Configuration – Access
You can select between the following buttons:
84
Button
Function
Cancel
Reject changes
Save
Save changes
2013-08-14
Configuration
Java Tool
 Select System > Access in the task area.
Menu System – Access
Pos: 57 /806-IHSE/Konfiguration/Systemeinstellung/480-xx/Switch @ 7\mod_1309938125852_6.doc @ 53104 @ 3 @ 1
2013-08-14
85
Draco tera
5.4.4
Switch
The configuration of the switching parameters is set in this menu.
You have the following possibilities to access the menu:
You can select between the following settings:
Field
Selection
Description
Video Sharing
activated
The user can switch to any CPU as an
observer, even to such ones that are
already assigned to another user
(observer without keyboard/mouse
access).

Note: Switching with the key
<Space>, not <Enter>.

The operator will not be informed if
further users connect as an
observer to the CPU that is
connected to his console.
deactivated Function not active (default)
Force Connect
activated
The user can connect to every single
CPU as an operator, even to such ones
that are related to another user.

Note: The previous user is set to
video only status.

To share K/M control, Force
Connect has to be activated.
deactivated Function not active (default)
Force
Disconnect
activated
Extension of Force Connect: If the user
connects to a CPU as an operator that is
already related to another user, the
connection to the previous user will be
completely disconnected.
Note: To share K/M control Force
Disconnect has to be deactivated.
deactivated Function not active (default)
86
2013-08-14
Configuration
Field
Selection
Description
CPU Auto
Connect
activated
If a console is not connected to a CPU,
you can establish an automatic
connection to the next available CPU by
hitting any key or mouse button.
deactivated Function not active (default)
CPU Timeout
0 – 999
minutes
Period of inactivity after which a console
will be automatically disconnected from
its current CPU (default value:
0 minutes)
Keyboard
Connect
activated
Activate request of K/M control by
keyboard event (key will be lost)
deactivated Function not active (default)
Mouse
Connect
activated
Activate request of K/M control by mouse
event
deactivated Function not active (default)
Release Time
0-999
seconds
Period of inactivity of a connected
console after which K/M control can be
requested by other consoles connected
to the CPU.

Note: Set "0" for an immediate
transfer in real-time.

Only one console can have
keyboard and mouse control at the
same time. The other consoles that
are connected to the same CPU
have a video only status (default
value: 10 seconds)
If the options Keyboard Connect and/or Mouse Connect are activated,
the condition Release Time will have to be met until a new user will gain
control.
2013-08-14
87
Draco tera
OSD
 Select Configuration > Switch in the main menu.
Menu Configuration – Switch
You can select between the following buttons:
88
Button
Function
Cancel
Reject changes
Save
Save changes
2013-08-14
Configuration
Java Tool
 Select System > Switch in the task area.
Menu System – Switch
Pos: 58 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
89
Draco tera
Pos: 59 /806-IHSE/Konfiguration/Systemeinstellung/480-xx/Netzwerk (Network) @ 7\mod_1309938178305_6.doc @ 53122 @ 3 @ 1
5.4.5
Network
The network configuration is set in this menu.
You have the following possibilities to access the menu:
You can select between the following settings:
Field
Selection
Description
DHCP
activated
The network settings are automatically
supplied by a DNS server
Note:
If DHCP is activated and there is no
physical network connection available,
the boot times might increase.
deactivated Function not active (default)
IP address
Byte
Input of the IP address, if DHCP is not
active (default: 192.168.100.99)
Subnet Mask
Byte
Input of the subnet mask in the form
"255.255.255.0", if DHCP is not active
(default: 255.255.255.0)
Gateway
Byte
Input of the subnet mask in the form
"192.168.1.1", if DHCP is not active
API Service
activated
LAN interface at the Draco tera activated
for access via Java tool (API service port
5555)
deactivated Function not active
FTP Server
activated
FTP server for transmission of
configuration files activated.
deactivated Function not active
Syslog
activated
Syslog server for status request is active
deactivated Function not active (default)
Syslog Server
90
Byte
Input of the IP address of the Syslog
servers in the form “192.168.1.1”
2013-08-14
Configuration
Field
Selection
Description
Trace
DEB
Activate debug messages in Trace
(default: NO)
Note:
The debug messages are exclusively for
matrix diagnostics. They only should be
activated after consultation with the
manufacturer. Otherwise an increased
traffic of data might limit the performance
of the CPU board.
INF
Activate information messages in Trace
(default: NO)
NOT
Activate notification messages in Trace
(default: YES)
WAR
Activate warning messages in Trace
(default: YES)
ERR
Activate error messages in Trace
(default: YES)
DEB
Activate debug messages in Syslog
(default: NO)
Note:
The debug messages are exclusively for
matrix diagnostics. They only should be
activated after consultation with the
manufacturer. Otherwise an increased
traffic of data might limit the performance
of the CPU board.
INF
Activate information messages in Syslog
(default: NO)
NOT
Activate notification messages in Syslog
(default: YES)
WAR
Activate warning messages in Syslog
(default: YES)
ERR
Activate error messages in Syslog
(default: YES)
Syslog
Activate the modified network parameters by doing a restart.
Consult your system administrator before modifying the network
parameters. Otherwise unexpected results and failures can occur in
combination with the network.
2013-08-14
91
Draco tera
OSD
 Select Configuration > Network in the main menu.
Menu Configuration – Network
You can select between the following buttons:
92
Button
Function
Cancel
Reject changes
Save
Save changes
2013-08-14
Configuration
Java Tool
 Select System > Network in the task area.
Menu System – Network
Pos: 60 /806-IHSE/Konfiguration/Systemeinstellung/480-xx/Datum und Uhrzeit @ 7\mod_1309938224352_6.doc @ 53140 @ 3 @ 1
2013-08-14
93
Draco tera
5.4.6
Date and Time
Date and Time are set in this menu, based on Simple Network Time
Protocol (SNTP).
You have the following possibilities to access the menu:
You can select between the following settings:
Field
Selection
Description
SNTP Client
activated
Enable network time server
synchronization
deactivated Function not active (default)
SNTP Server
Byte
Input of the SNTP server IP address
(default: 000.000.000.000)
Time Zone
Region
Set your specific time zone
Month
1–12
Enter month
Date
1–31
Enter date
Year
1–99
Enter year
Day
1–7
Enter day of the week
Hours
0–23
Enter hour
Minutes
0–59
Enter minute
Seconds
0–59
Enter second
Date format according to the English notation.
94
2013-08-14
Configuration
OSD
 Select Configuration > Date+Time in the main menu.
Menu Configuration – Date + Time
In order to configure a time server, proceed as follows:
1.
Set the option SNTP Client to Y (Yes).
2.
Enter the IP address of your SNTP server in the field SNTP Server.
3.
Select your time zone in the field Time Zone.
4.
Press the button Okay to confirm your settings.
5.
Restart the matrix. The system time will be now provided by the
SNTP server.
In order to set the real time clock without using SNTP, proceed as follows:
1.
Set the current date in the field Date.
2.
Set the current Day in the field Day.
3.
Set the current time in the field Time.
4.
Press the button RTC to confirm your settings.
2013-08-14
95
Draco tera
Java
 Select System > Date and Time in the main menu.
Menu Configuration – Date and Time
In order to configure a time server, proceed as follows:
1.
Enable option SNTP.
2.
Enter the IP address of your SNTP server in the field SNTP Server.
3.
Select your time zone in the field Time Zone.
4.
Press the button Apply to confirm your settings.
5.
Restart the matrix. The system time will be now provided by the
SNTP server.
In order to set the real time clock without using SNTP, proceed as follows:
1.
Set the current date in the field Date and Time.
2.
Set the current time in the field Day and Time.
3.
Press the button Apply to set the system time.
4.
Option: If you want to receive the time from your currently used
computer, press the button Get Local Time.
Pos: 61 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
96
2013-08-14
Configuration
Pos: 62 /806-IHSE/Konfiguration/480_Benutzereinstellungen/480-xx/Benutzereinstellungen @ 7\mod_1309938277711_6.doc @ 53160 @ 2 @ 1
5.5
User Settings
You have the possibility to configure the following user settings:
Pos: 63 /806-IHSE/Konfiguration/480_Benutzereinstellungen/480-xx/User @ 7\mod_1309938316977_6.doc @ 53178 @ 3 @ 1
5.5.1
User
New users and their user settings and permissions are set in this menu.
You have the following possibilities to access the menu:
You can select between the following settings:
Field
Selection
Description
Name
Text
User name (case sensitive)
Password
Text
User password (case sensitive)
Repeat
Password
Text
Repeat user password (case sensitive)
FTP
activated
Access permission via FTP. This setting
is necessary for file access from the
Java tool or any web browser.
deactivated Function not active (default).
Power User
activated


User has user rights
Permission to switch consoles to
CPUs in Extended Switching
according to the CON or User ACL
deactivated Function not active.
Super User
activated
Permission to switch any console to any
CPU in Extended Switching.
deactivated Function not active.
Administrator
activated



Permission for system configuration
and all switching operations
User has administrator rights
This setting is required for an online
connection with the Java tool
deactivated Function not active.
2013-08-14
97
Draco tera
OSD
 Select Configuration > User in the main menu.
Menu Configuration – User
You can select between the following buttons:
98
Button
Function
New
Create a new user
Edit
Edit an existing user
Delete
Delete an existing user
Cancel
Reject changes
Save
Save changes
2013-08-14
Configuration
Java Tool
 Select Definition > User in the task area.
Menu Definition – User
You can select between the following buttons:
Button
Function
New
Open a new user configuration
Delete
Delete an existing user
Apply
Create a new user account
Cancel
Reject changes
In order to configure a user access rights for CPUs, proceed as follows:
1.
Select a user in the list User.
2.
By using the right mouse button once on a CPU in one of the
respective access lists (Full Access, Video Access and No Access)
two lists for selection will appear in which the respective CPU can be
moved and the access rights can be changed.
3.
Confirm the configuration with the button Apply.
2013-08-14
99
Draco tera
In order to create a new user, proceed as follows:
1.
Press the button New.
2.
Select a template of an existing user if applicable (Choose template).
3.
Press the button OK.
4.
Set a user name.
5.
Set a password.
6.
Set general access permissions.
7.
Set user permissions for CPU access (paste function).
8.
Set user favorites for OSD access.
9.
Press the button Apply to save the new user settings.
You can select between the following keyboard commands:
Function
Keyboard Command
Add CPU to list Full Access
<F>
Add CPU to list Video Access
<V>
Add CPU to list No Access
<N>
Pos: 64 /806-IHSE/Konfiguration/480_Benutzereinstellungen/480-xx/Favoritenliste Benutzer @ 7\mod_1321429770828_6.doc @ 54740 @ 3 @ 1
5.5.2
Favorite List Users
Individual favorite lists of CPUs that have to be switched frequently can be
created for different users in this menu. A favorite list can contain up to
eight different CPUs.
The switching of the favorites is done via 'Hot Key' using the keyboard
(see Chapter 6.1.1, Page 157).
You have the following possibilities to access the menu:
100
2013-08-14
Configuration
OSD
 Select Assignments > User Favorites in the main menu.
Menu Assignments – User Favorites
To create a favorite list for you own user, proceed as follows:
1.
Select successively these CPUs from the list CPU Devices that have
to be moved to the favorite list. By pressing the key <a>, a
CPU device will be moved to the favorite list and it will be removed by
pressing <r>.
2.
The order of the CPU devices within the favorite list can be changed
by pressing the keys <+> and <->.
3.
Press the button Save to save the settings.
2013-08-14
101
Draco tera
Java-Tool
 Select the respective user in the working area of the menu User for
the favorite list and open the tab Favorites.
Menu Definition – User
To create a favorite list for any user, proceed as follows:
1.
Select the CPUs in the list CPU available that should be added to the
favorite list (CPU assigned). By pressing the key <Ctrl> at the same
time, more than one CPU device can be marked.
2.
Press the button > to move the marked CPU devices to the favorite
list. If you press the button >>, the first eight CPU devices from the list
CPU available will be moved to the favorite list (CPU assigned).
3.
The order of marked CPU devices within the favorite list can be
changed by pressing the keys<+> and <->.
4.
In order to remove marked CPU devices from the favorite list, press
the button <. If you press the button <<, all CPU devices will be
removed from the favorite list.
Pos: 65 /806-IHSE/Konfiguration/480_Benutzereinstellungen/480-xx/Benutzer-Makros @ 7\mod_1330938207784_6.doc @ 57881 @ 3 @ 1
102
2013-08-14
Configuration
5.5.3
User Macros
In this menu macro commands for switching, disconnection or user
administration can be created. The macro commands are created for each
user separately.
A macro can execute up to 16 switching commands successively.
The execution of the macros is done via 'Hot Key' and the function keys
<F1>-<F16> (see Chapter 6.1.3, Page 159).
In order to execute user macros the user has to be logged in at the matrix.
You can select between the following settings:
Field
Selection
Description
Function
(01–16)
Connect
(P1=CON,
P2=CPU)
Set bidirectional connection from
console P1 to CPU P2
Connect Video
(P1=CON, P2=
CPU)
Set video connection from console P1
to CPU P2
Disconnect
(P1=CON)
Disconnect console P1
Logout User
Logout current user
Set Real CPU
(P1=VCPU,
P2=RCPU)
Assign a virtual CPU to a real CPU
Set Virtual CON
(P1=RCON,
P2=VCON)
Assign a real console to a virtual
console
Push (P1=CON)
The own KVM connection is forwarded
to console P1 and is changed to a
video only connection.
Push Video
(P1=CON)
The video signal of the current
connection (KVM or video only) is
forwarded to console P1. The own
connection remains unchanged (KVM
or video only).
2013-08-14
103
Draco tera
Field
Selection
Description
Get (P1=CON)
The own console gets a KVM
connection to the CPU that is currently
connected to console P1. The
connection of console P1 is changed
into a video only connection.
Get Video
(P1=CON)
The own console gets a video only
connection to the CPU that is currently
connected to console P1. The
connection of console P1 remains
unchanged (KVM or video only).
P1
CON or CPU
Device
Name of CON or CPU device
P2
CPU or CPU
Device
Name of CON or CPU device
You have the following possibilities to access the menu:
104
2013-08-14
Configuration
OSD
 Select via Configuration > User Macros in the main menu the user
for which a user macro has to be created.
Menu Configuration – User Macros
In order to create a macro for the selected user, proceed as follows:
1.
Select in the field Key that one (1-16) for which a macro has to be
created.
2.
Select the respective place on the list (1-16) of the key that has to be
set with a macro key.
3.
Select for the marked place on the list a macro command in the field
Macro Data.
4.
Set the necessary parameters P1 and P2 (e.g. CON Devices or CPU
Devices) for the selected macro command.
5.
Confirm your inputs by pressing the key <Enter> and repeat the
process for further macro commands, if necessary.
2013-08-14
105
Draco tera
Java-Tool
 Select in the working area of menu Definition > User the user for
which macros have to be created and open the tab Macros.
Menu Definition – User
In order to create a macro for the selected user, proceed as follows:
1.
Select in the field Key that one (1-16) for which a macro has to be
created.
2.
Select in the column Function the commands that should be part of
the macro. The selection list is opened by a double click on the empty
fields.
3.
Select in the columns P1 and P2 the respective parameters for the
macro functions (e.g. corresponding consoles and CPUs).
4.
Confirm your inputs by pressing the button Apply.
For an efficient macro configuration the following context functions are
available:
 Via right click on the tab Macros, macros can be assigned to other
users by using the function Assign Macros to ... and can be copied
from other users by using the function Copy Macros from ....
106
2013-08-14
Configuration
 Via right click on the macro list, macros of the selected key can be
copied into the cache by using the function Copy Key Macros. You
can paste the macros from the cache into a key by using the function
Paste Key Macros and you can reset all macros of the selected key
by using the function Reset Key Macros.
Pos: 66 /806-IHSE/Konfiguration/480_Extender-Einstellungen/480-xx @ 7\mod_1309938366618_6.doc @ 53197 @ 23333 @ 1
5.6
Extender Settings
All extender units are managed in this menu. This also contains the
creation of new extender units and the deletion of existing extender units.
The extender unit describes the connection of an physical extender to the
matrix. Every extender board with a direct cable connection to the matrix
is recognized as an extender unit. Dual-Head KVM extenders will be
recognized as two independent extender units.
KVM Extenders automatically create extender units inside the matrix.
You have the following possibilities to access the menu:
You can select between the following settings:
Field
Selection
Description
ID
Text
Numerical value of the extender ID
(KVM extenders: ID is provided by
extender unit (Serial No.) and cannot be
changed)
Name
Text
Name of the extender unit
Fixed
activated
Create an extender unit with a fixed port
assignment (default)
deactivated Function not active.
Port
2013-08-14
1–288
(depending
on the
matrix)
Port number of the extender unit
107
Draco tera
OSD
 Select Configuration > EXT Units in the main menu.
Menu Configuration – EXT Units
You can select between the following buttons:
Button
Function
New
Create a new extender unit
Edit
Edit an existing extender unit
Delete
Delete an existing extender unit
Cancel
Reject changes
Save
Save changes
The settings for the tab OSD Data are described in Chapter 5.8.2,
Page 120.
108
2013-08-14
Configuration
Java Tool
 Select Definition > EXT Units in the task area.
Menu Definition – EXT Units
You can select between the following buttons:
5.6.1
Button
Function
New
Create a new extender unit
Delete
Delete an existing unit
Apply
Confirm changes of an extender unit
Cancel
Reject changes
Creating Flex-Port Extender Unit
Extenders with ID function are automatically recognized by the system
and cannot be created manually. They were used at so called Flex-Ports
at the matrix.
The connection of fixed port extender unit (e. g. USB 2.0) to a Flex-Port
can cause unintended results.
2013-08-14
109
Draco tera
5.6.2
Creating Fixed Port Extender Units
In order to create a fixed port extender unit (e. g. USB 2.0), proceed as
follows:
1.
Press the button New.
2.
Select, if a template of a USB 2.0 CON unit (USB CON Unit) or
USB 2.0 CPU unit (USB CPU Unit) should be used.
3.
Press the button OK.
4.
Determine a port at the matrix that should be used with the USB 2.0
extender unit (Fixed Port). As an option the name of the USB 2.0
extender unit can be changed (Name).
5.
Press the button Apply to save the new extender unit.
Created extender units are always set as fixed port extenders. These
configurations are necessary, if you want to switch e. g. USB 2.0
connections via the matrix.
5.6.3
Deleting Flex-Port Extender Units
Deleting Flex-Port extender units connected to the matrix is not possible.
5.6.4
Deleting Fixed Port Extender Units
In order to delete a fixed port extender unit (e. g. USB 2.0), proceed as
follows:
1.
Verify that the fixed port extender unit to be deleted is currently not
assigned to a device.
2.
Select the fixed port extender unit to be deleted in the selection list on
the left side of the menu EXT Units and confirm with the key <Enter>.
3.
Press the button Delete.
4.
Confirm the delete process with the button Okay.
In order to make a fixed port available again for Flex-Port extender units
after deleting a fixed port extender unit, a restart of the I/O board is
obligatory.
Pos: 67 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
110
2013-08-14
Configuration
Pos: 68 /806-IHSE/Konfiguration/480_CPU-Einstellungen/480-xx @ 7\mod_1309938442055_6.doc @ 53216 @ 2 @ 1
5.7
CPU Settings
New CPU devices are configured in this menu including their assignment
to extenders.
The assignment helps to describe and switch more complex computer
configurations (e.g. Quad-Head with USB 2.0) in the matrix.
You have the following possibilities to access the menu:
You can select between the following settings:
Field
Selection
Description
ID
Text
ID of the CPU unit (see Chapter 5.4.2,
Page 79).
Name
Text
Name of the CPU Device.
Virtual Device
activated
Create new CPU device as a virtual one.
deactivated Function not active (default).
Allow Private
activated
Allow switching to the respective CPU
device in Private Mode
deactivated Function not active (default).
Force Private
activated
Force switching to the respective CPU
only in Private Mode.
deactivated Function not active (default).
Fix Frame
activated
Force showing a red frame when
switching to the respective CPU.
deactivated Function not active (default).
2013-08-14
111
Draco tera
OSD
 Select Configuration > CPU Units in the main menu.
Menu Configuration – CPU Devices
You can select between the following buttons:
112
Button
Function
New R.
Create a new real CPU device
New V.
Create a new virtual CPU device
Edit
Edit an existing CPU device
Delete
Delete an existing CPU device
Cancel
Reject changes
Save
Save changes
2013-08-14
Configuration
Java Tool
 Select Definition > CPU Devices in the task area.
Menu Definition – CPU Devices
You can select between the following buttons:
Button
Function
New
Open a new CPU Device
Delete
Delete a new CPU Device
Apply
Confirm a created CPU Device
Cancel
Reject changes
>
Assign selected extender units
>>
Assign all available extender units
<
Remove the selected extender units
<<
Remove all extender units
2013-08-14
113
Draco tera
You can select between the following keyboard commands:
Function
Keyboard Command
Change assignment number of the EXT unit
upwards
<+>
Change assignment number of the EXT unit
downwards
<->
In order to create a new CPU device, proceed as follows:
1.
Press the button New.
2.
Select, if a real CPU (Create a real CPU) or a virtual CPU (Create a
virtual CPU) should be created or a template of an existing CPU
should be used (Choose template).
A template can only be used, if there is at least one existing CPU device.
3.
Press the button OK.
4.
Determine all parameters that are relevant for the CPU.
5.
To confirm the new CPU, press the button Apply.
In order to access a new CPU via matrix, an assignment of one or more
CPU type extender units is required. Proceed as follows:
1.
Select the new CPU in the list CPU Devices.
2.
Select one or more extenders in the list Extender available.
3.
Perform the assignment by pressing the button >. To assign all
available extenders to the CPU, press the button >>.
The assignments are displayed in the list Extender assigned.
4.
Confirm the assignment by pressing the button Apply.
In order to remove an extender assignment, proceed as follows:
1.
Select a CPU in the list CPU Devices.
2.
Select one or more extenders in the list Extender assigned.
3.
Remove the assignment with the button <. To remove all existing
assignments, press the button <<.
4.
Confirm the removal with the button Apply.
Pos: 69 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
114
2013-08-14
Configuration
Pos: 70 /806-IHSE/Konfiguration/480_Konsolen-Einstellungen/480-xx/Konsolen-Einstellungen @ 7\mod_1309938518774_6.doc @ 53236 @ 2 @ 1
5.8
Console Settings
You have the possibility to perform the following console settings:
Pos: 71 /806-IHSE/Konfiguration/480_Konsolen-Einstellungen/480-xx/CON Devices @ 7\mod_1309938548274_6.doc @ 53254 @ 3 @ 1
5.8.1
CON Devices
New CON devices are created in this menu including access rights and
assignment to extenders.
You have the following possibilities to access the menu:
You can select between the following settings:
Field
Selection
Description
ID
Text
ID of the CON unit (see Chapter 5.4.2,
Page 79).
Name
Text
Name of the CON device.
Virtual Device
activated
Create new CON device as a virtual
one.
deactivated
Function not active (default).
activated
Allow activation of the User ACL at the
local console.
deactivated
Function not active (default).
activated
Force user login at this CON device.
Allow User
ACL
Force Login
LOS Frame
deactivated
Function not active (default).
activated


deactivated
2013-08-14
When losing the video signal
between source (computer, CPU)
and the CPU unit or when losing
the connection between the matrix
and the CON unit, there will be
displayed an orange frame.
When switching to a CPU without
video signal, a blank screen will
appear surrounded by an orange
frame.
Function not active (default).
115
Draco tera
Field
Selection
Description
Allow CPU
Scan
activated
Allow a scan mode with an automatic
change of the video signal for the
favorite list (CPU devices) of the
respective console or a logged in user.
deactivated
Function not active (default).
Force CPU
Scan
activated
Force a scan mode with an automatic
change of the video signal for the
favorite list (CPU devices) of the
respective console or a logged in user.
Scan Time
116
deactivated
Function not active (default).
0-99
seconds
Retention period until switching to the
next CPU device.
2013-08-14
Configuration
OSD
 Select Configuration > CON Devices in the main menu.
Menu Configuration – CON Devices
You can select between the following buttons:
Button
Function
New R.
Create a real console
New V.
Create a virtual console
Edit
Edit an existing console
Delete
Delete an existing console
Cancel
Reject changes
Save
Save changes
2013-08-14
117
Draco tera
Java Tool
 Select Definition > CON Devices in the task area.
Menu Definition – CON Devices
You can select between the following buttons:
118
Button
Function
New
Open a new CON device
Delete
Delete a new CON device
Apply
Confirm a created CON device
Cancel
Reject changes
>
Assign selected extender units
>>
Assign all available extender units
<
Remove the selected extender units
<<
Remove all extender units
2013-08-14
Configuration
You can select between the following keyboard commands:
Function
Keyboard Command
Decrease assignment number of the extender
unit
<+>
Increase assignment number of the extender
unit
<->
In order to create a new console, proceed as follows:
1.
Press the button New.
2.
Select, if a real console (Create a real Console) or a virtual console
(Create a virtual Console) should be created or a template of an
existing console should be used (Choose template).
A template can only be used, if there is at least on existing CON device.
3.
Press the button OK.
4.
Determine all parameters that are relevant for the console.
5.
To confirm a created console, press the button Apply.
In order to run a created CPU via matrix, it requires an assignment of one
or more CON units (extender). To place an assignment, please proceed
as follows:
1.
Select the console in the list CON Devices that has to be assigned to
an extender.
2.
Select the extender in the list Extender available that should be
assigned to the CON.
3.
Perform the assignment by pressing the button >. To assign all
available extenders to the console, press the button >>. The
assignments are displayed in the list Extender assigned.
4.
Confirm the assignment by pressing the button Apply.
In order to remove an extender assignment, proceed as follows:
1.
Select the console in the list CON Devices to be modified.
2.
Select the extender(s) in the list Extender assigned to be removed.
3.
Remove the assignment with the button <. To remove all existing
assignments, press the button <<.
4.
Confirm the changes by pressing the button Apply.
2013-08-14
119
Draco tera
In order to configure CPU access rights of consoles, proceed as follows:
1.
Select a console in the list CON Devices.
2.
Open the tab CPU Access Control.
3.
Assign new access rights by using the right mouse button or the
respective keyboard commands (cf. below).
4.
Confirm the configuration by pressing the button Apply.
You can select between the following keyboard commands:
Function
Keyboard Command
Add CPU to list Full Access
<F>
Add CPU to list Video Access
<V>
Add CPU to list No Access
<N>
Pos: 72 /806-IHSE/Konfiguration/480_Konsolen-Einstellungen/480-xx/Maus und Tastatur @ 7\mod_1309938591211_6.doc @ 53272 @ 3 @ 1
5.8.2
Mouse and Keyboard
The OSD configuration for mouse and keyboard is made in this menu.
You have the following possibilities to access the menu:
You can select between the following settings:
Field
Selection
Description
Hor. Speed 1/x
1–9
Adjustment of the horizontal mouse
speed, 1 = slow, 9 = fast (default
value: 4)
Ver. Speed 1/x
1–9
Adjustment of the vertical mouse speed,
1 = slow, 9 = fast (default value: 5)
Double Click
100–800
Adjustment of the time slot for a double
click (default value: 200 ms)
Keyboard
layout
Region
Set the OSD keyboard layout according
to the used keyboard (default: German
(DE))
Video Mode
Variable or
specific
resolution
Resolution that is used when opening
OSD
The mouse and keyboard settings are console specific and can be
separately set for each console.
120
2013-08-14
Configuration
OSD
 Select Configuration > EXT Units in the main menu.
Menu Configuration – EXT Units
You can select between the following buttons:
Button
Function
Cancel
Reject changes
Save
Save changes
2013-08-14
121
Draco tera
Java Tool
 Select Definition > EXT Units in the task area.
Mouse and keyboard settings are made in the tab OSD Data.
Menu Definition – EXT Units
Pos: 73 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
122
2013-08-14
Configuration
Pos: 74 /806-IHSE/Konfiguration/480_Konsolen-Einstellungen/480-xx/Extender OSD @ 8\mod_1351502028499_6.doc @ 69501 @ 3 @ 1
5.8.3
Extender OSD
In this menu the settings for the Extender OSD can be adjusted. These
are local settings that can be made individually for each console.
You can select between the following Extender OSD settings:
Field
Selection
Description
Enable CPU
Selection
activated
When executing the key sequence for
opening the OSD, a selection list for
switching CPU devices will be displayed
in the center of the monitor. Pressing the
button <F7> within the selection list
opens the standard OSD.
deactivated Function not active (default)
Enable
Connection
Info
activated
Update
Connection
Info
activated
Display Time
0-999
seconds
Duration of OSD fade-in (default: 10)
Horizontal
Position
10 pixels
Horizontal OSD position (default: -2)
Vertical
Position
10 pixels
Vertical OSD position (default: 2)
Enable Extender OSD (default: YES)
deactivated Function not active
Update connection changes during fadein of Extender OSD (default: YES)
deactivated Function not active
When setting the horizontal OSD position, a prefixed minus describes the
orientation to the right edge of the monitor, e.g. -2 means 2 x 10 = 20
pixels of distance to this edge. When setting a vertical position, a prefixed
minus describes the orientation to the bottom edge of the monitor.
If the function Update Connections is deactivated, the Extender OSD
only appears when switching via OSD.
You have the following possibility to access the menu:
2013-08-14
123
Draco tera
OSD
 Select Configuration > EXT Units in the main menu.
Menu Configuration – EXT Units
In order to change the Extender OSD settings, proceed as follows:
124
1.
Select the console extender in the list EXT Units whose Extender
OSD settings has to be adjusted.
2.
When confirming the selection by pressing the key <Enter>, the
respective console extender will be enabled for editing.
2013-08-14
Configuration
Java-Tool
 Select Definition > EXT Units in the task area.
Menu Definition – EXT Units
In order to change the Extender OSD settings, proceed as follows:
1.
Select the console extender in the list EXT Units whose Extender
OSD settings has to be adjusted.
2.
Open the tab Extender OSD Data.
3.
Adjust the desired settings and confirm your changes by pressing the
button Apply.
Pos: 75 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
125
Draco tera
Pos: 76 /806-IHSE/Konfiguration/480_Konsolen-Einstellungen/480-xx/Favoritenliste Konsolen @ 7\mod_1321435290266_6.doc @ 54758 @ 3 @ 1
5.8.4
Favorite List Consoles
Individual favorite lists of CPUs that have to be switched frequently can be
created for all consoles in this menu. A favorite list can contain up to
16 different CPUs.
The switching of the favorites is done via 'Hot Key' using the keyboard
(see Chapter 6.1.1, Page 157).
You have the following possibilities to access the menu:
OSD
 Select Assignments > CON Favorites in the main menu.
Menu Assignments – CON Favorites
126
2013-08-14
Configuration
To create a favorite list for your own console, proceed as follows:
1.
Select successively these CPUs from the list CPU Devices that have
to be moved to the favorite list. By pressing the key <a>, a
CPU device will be moved to the favorite list and it will be removed by
pressing <r>.
2.
The order of the CPU devices within the favorite list can be changed
by pressing the keys <+> and <->.
3.
Press the button Save to save the settings.
Java-Tool
 Select the respective user in the working area of the menu
CON Devices for the favorite list and open the tab Favorites.
Menu Definition – CON Devices
2013-08-14
127
Draco tera
To create a favorite list for any console, proceed as follows:
1.
Select the CPUs in the list CPU available that should be added to the
favorite list (CPU assigned). By pressing the key <Ctrl> at the same
time, more than one CPU device can be marked.
2.
Press the button > to move the marked CPU devices to the favorite
list. If you press the button >>, the first eight CPU devices from the list
CPU available will be moved to the favorite list (CPU assigned).
3.
The order of marked CPU devices within the favorite list can be
changed by pressing the keys<+> and <->.
4.
To remove marked CPU devices from the favorite list, press the
button <. If you press the button <<, all CPU devices will be removed
from the favorite list.
Pos: 77 /806-IHSE/Konfiguration/480_Konsolen-Einstellungen/480-xx/Konsolen-Makros @ 7\mod_1330939768963_6.doc @ 57900 @ 3 @ 1
5.8.5
Console Macros
In this menu macro commands for switching, disconnection or user
administration can be created. The macro commands are created for each
console separately.
A macro can execute up to 16 switching commands successively.
The execution of the macros is done via 'Hot Key' and the function keys
<F1>-<F16> (see Chapter 6.1.3, Page 159).
You can select between the following settings:
128
Field
Selection
Description
Function
(01–16)
Connect
(P1=CON,
P2=CPU)
Set bidirectional connection from
console P1 to CPU P2
Connect Video
(P1=CON, P2=
CPU)
Set video connection from console P1
to CPU P2
Disconnect
(P1=CON)
Disconnect console P1
Logout User
Logout current user
Set Real CPU
(P1=VCPU,
P2=RCPU)
Assign a virtual CPU to a real CPU
2013-08-14
Configuration
Field
Selection
Description
Set Virtual CON
(P1=RCON,
P2=VCON)
Assign a real console to a virtual
console
Push (P1=CON)
The own KVM connection is forwarded
to console P1 and is changed to a
video only connection.
Push Video
(P1=CON)
The video signal of the current
connection (KVM or video only) is
forwarded to console P1. The own
connection remains unchanged (KVM
or video only).
Get (P1=CON)
The own console gets a KVM
connection to the CPU that is currently
connected to console P1. The
connection of console P1 is changed
into a video only connection.
Get Video
(P1=CON)
The own console gets a video only
connection to the CPU that is currently
connected to console P1. The
connection of console P1 remains
unchanged (KVM or video only).
P1
CON or CPU
Device
Name of CON or CPU device
P2
CPU or CPU
Device
Name of CON or CPU device
You have the following possibilities to access the menu:
2013-08-14
129
Draco tera
OSD
 Select via Configuration > CON Macros in the main menu that
console for which a console macro has to be created.
Menu Configuration – CON Macros
In order to create a macro for the selected console, proceed as follows:
130
1.
Select in the field Key that one (1-16) for which a macro should be
created.
2.
Select the respective place on the list (1-16) of the key that should be
set with a macro key.
3.
Select for the highlighted position on the list a macro command in the
field Macro Data.
4.
Set the necessary parameters P1 and P2 (e.g. CON Devices or CPU
Devices) for the selected macro command.
5.
Confirm your inputs by pressing the key <Enter> and repeat the
process for further macro commands, if necessary.
2013-08-14
Configuration
Java-Tool
 Select the console in the working area of the menu Definition > CON
Devices for which a macro has to be created and open the tab
Macros.
Menu Definition – CON Devices
In order to create a macro for the selected console, proceed as follows:
1.
Select in the field Key that one (1-16) for which a macro has to be
created.
2.
Select in the column Function the commands that should be part of
the macro. The selection list will be opened by a double click on the
empty fields.
3.
Select the respective parameters for the macro functions (e.g.
corresponding consoles and CPUs) in the columns P1 and P2.
4.
Confirm your inputs by pressing the button Apply.
2013-08-14
131
Draco tera
For an efficient macro configuration the following context functions are
available:
 When clicking on the tab Macros, macros can be assigned to other
consoles by using the function Assign Macros to ... and can be
copied from other consoles by using the function Copy Macros
from ....
 When clicking on the macro list, macros of the selected key can be
copied into the cache by using the function Copy Key Macros. You
can paste the macros from the cache into a key by using the function
Paste Key Macros and you can reset all macros of the selected key
by using the function Reset Key Macros.
Pos: 78 /806-IHSE/Konfiguration/480_Konsolen-Einstellungen/480-xx/Konkurrierende Bedienung @ 9\mod_1375170037949_6.doc @ 79211 @ 3 @ 1
5.8.6
Parallel Operation
In this chapter you can find an instruction of configuring the parallel
operation of a CPU Device by two or more CON Devices. The control of
the CPU Device can be done by only one CON Device at a time, but can
be taken over exclusively by other CON Devices, too. Taking over control
is immediately possible or after the expiry of an inactivity timer of the
controlling CON Device. You can use the mouse or keyboard in order to
take over control.
In order to allow a smooth and accurate function of the parallel operation,
you should use identical mice and keyboards. They should be connected
to the same USB-HID ports of each CON Unit.
The alternative is using the USB-HID Ghosting (see Chapter 6.10,
Page 177).
You have the following possibilities to configure parallel operation:
132
2013-08-14
Configuration
OSD
 Select Configuration > Switch in the main menu.
Menu Configuration – Switch
In order to configure parallel operation, proceed as follows:
1.
Activate the function Enable Video Sharing.
2.
Activate the function Force Connect.
3.
Activate the function Keyboard Connect, if taking over control by a
keyboard event should be possible.
4.
Activate the function Mouse Connect, if taking over control by a
keyboard movement should be possible.
5.
Define a Release Time of inactivity (0 - 999 sec.) after that control
can be taken over.
2013-08-14
133
Draco tera
Java-Tool
 Select System > Switch in the task area.
Menu System – Switch
In order to configure parallel operation, proceed as follows:
1.
Activate the function Enable Video Sharing.
2.
Activate the function Force Connect.
3.
Activate the function Keyboard Connect, if taking over control by a
keyboard event should be possible.
4.
Activate the function Mouse Connect, if taking over control by a
keyboard movement should be possible.
5.
Define a Release Time of inactivity (0 - 999 sec.) after that control
can be taken over.
Pos: 79 /806-IHSE/Konfiguration/480_Konsolen-Einstellungen/480-xx/Multi-Screen-Kontrolle @ 8\mod_1360595667772_6.doc @ 71051 @ 3 @ 1
134
2013-08-14
Configuration
5.8.7
Multi-Screen Control
In this menu switching of USB-HID to control several connected sources
(computer, CPU) by a CON device with several monitors can be
configured. The switching can be performed for up to four connected
sources (computer, CPU) and is made smoothly by crossing the mouse
pointer beyond the respective monitor to the next one.
Thereby, the monitors can be arranged in sequence or as a square.
When using sources (computers, CPUs) in multi-head operation (e.g.
dual-head), the switching is only working manually via keyboard
commands. Any non-observance may have a negative influence on the
stability of the system.
In order to enable Multi-Screen Control, all Extender Units assigned to the
related CON device, have to be physically connected to the same block of
4 ports on the I/O board of the matrix.
CON Units that have been already configured for Multi-Screen Control can
be connected together to other blocks of 4 ports. In this case any further
configuration is not necessary. The functionality will be still available.
You have the following possibilities to access the menu:
2013-08-14
135
Draco tera
OSD
 Select Assignments > Multi-Screen Control in the main menu.
Menu Assignments – Multi-Screen Control
In order to configure the Multi-Screen Control, proceed as follows:
136
1.
Select in the field Arrangement the respective display arrangement
that is available at the CON Device you want to configure (1 x 4 or
2 x 2).
The fields for the configuration of the individual displays will be
arranged accordingly.
2.
Activate the option Manual, if the USB-HID switching should only be
allowed by using keyboard commands (see Chapter 6.7, Page 173).
The manual switching allows the use of multi-head consoles.
3.
Ensure that the option Enabled is set to Y on all used displays in
order to activate the respective display for the use of the Multi-Screen
Control.
2013-08-14
Configuration
4.
Select one or more control displays within the CON Device by setting
the function Control auf Y in the respective display field.
Control displays are referred to the extender units within the MultiScreen Control that are connected to keyboard and mouse.
5.
When using the function Owner, you can determine which control
display is permitted for USB-HID switching to the different displays.
Select that display from the list.
In order to make a display accessible for all neighboring control
displays, set the function Owner to shared.
6.
Use the function Frame to configure a red frame that shows the
current display with mouse control after the expiration of a selectable
timer.
The frame to fade in can be individually activated by using a timer
>0 seconds.
Java-Tool
 Select Assignment > Multi-Screen Control in the main menu.
Menu Assignment – Multi-Screen Control
2013-08-14
137
Draco tera
In order to configure the Multi-Screen Control, proceed as follows:
1.
Select that block of 4 ports in the list of the working area which should
be configured for Multi-Screen Control.
There are only shown these blocks of 4 ports that contain at least one
CON Unit.
2.
Activate the option Manual, if the USB-HID switching should only be
allowed by using keyboard commands (see Chapter 6.7, Page 173).
The manual switching allows the use of multi-head consoles.
3.
Select in the field Arrangement the respective display arrangement
that is available at the CON Device you want to configure (1 x 4 or
2 x 2).
The fields for the configuration of the individual displays will be
arranged accordingly.
4.
Select one or more control displays within the CON Device by setting
the function Control auf Y in the respective display field.
Control displays are referred to the extender units within the MultiScreen Control that are connected to keyboard and mouse.
5.
When using the function Owner, you can determine which control
display is permitted for USB-HID switching to the different displays.
Select that display from the list.
In order to make a display accessible for all neighboring control
displays, set the function Owner to shared.
6.
Use the function Frame to configure a red frame that shows the
current display with mouse control after the expiration of a selectable
timer.
The frame to fade in can be individually activated by using a timer
>0 seconds.
Pos: 80 /806-IHSE/Konfiguration/480_Speichern und Laden von Konfigurationen/480-xx/Speichern und Laden von Konfigurationen @ 7\mod_1309938757899_6.doc @ 53292 @ 2 @ 1
138
2013-08-14
Configuration
5.9
Saving and Loading of Configurations
You have the possibility to set the following administration of
configurations:
Pos: 81 /806-IHSE/Konfiguration/480_Speichern und Laden von Konfigurationen/480-xx/Zwischenspeichern von Konfigurationen @ 7\mod_1309945736118_6.doc @ 54172 @ 3 @ 1
5.9.1
Active Configuration
You have the following possibility to access the menu:
 Select Configuration > Save in the main menu.
By selecting this menu item, the active configuration of the matrix is
saved to the permanent matrix memory. By default, the last
configuration that has been saved in this way will be restored after a
restart of the matrix.
Changing configurations or saving them blocks the matrix memory and
leads to a freeze of all OSD menus for a few seconds. The switching
connections are not affected by this freeze.
If you select Auto Save within the system settings an additional automatic
saving of the configuration will be performed periodically (see Chapter
5.3.2, Page 72).
Pos: 82 /806-IHSE/Konfiguration/480_Speichern und Laden von Konfigurationen/480-xx/Speichern von Konfigurationen (intern) @ 7\mod_1309938789321_6.doc @ 53310 @ 3 @ 1
5.9.2
Saving of Configurations (internal)
In this menu the current matrix configuration to predefined storage
locations is saved. However, it does not replace the buffering of
configuration (see Chapter 5.9.1, Page 139).
You have the following possibilities to access the menu:
In Active, the name and detailed information of the current configuration
are shown. This configuration can be saved now.
In Default and File #1 to File #8, the name and the detailed information of
the respective saved configuration are shown. These storage locations
can be overwritten.
2013-08-14
139
Draco tera
The storage location that has to be overwritten by the current configuration
must be selected explicitly.
Afterwards the current configuration will be saved to this storage location
and will be immediately shown in the menu. The previously saved
configuration that has been saved to this storage location is deleted.
OSD
You have the possibility to save the created configuration within eight
storage locations in the matrix (File #1 – File #8). Additionally a
configuration can also be saved as default configuration.
1.
Select Configuration > Save As… in the main menu.
2.
Select the required storage location (File #1 – File #8) or Default.
Menu Configuration – Save as
140
2013-08-14
Configuration
Java Tool
To save the configuration into the internal matrix memory, proceed as
follows:
1.
Select File > Upload in the menu bar.
2.
Enter the IP address of the matrix, your user name and your
password and confirm your inputs with the button Next.
3.
Select the storage location in that the configuration has to be saved
(default or config01 – config08) and confirm with the button OK.
Menu File – Upload
Pos: 83 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
141
Draco tera
Pos: 84 /806-IHSE/Konfiguration/480_Speichern und Laden von Konfigurationen/480-xx/Laden von Konfigurationen (intern) @ 7\mod_1309938889118_6.doc @ 53346 @ 3 @ 1
5.9.3
Loading of Configurations (internal)
Previously saved configurations are loaded in this menu.
You have the following possibilities to load configurations from files:
In Active, the currently loaded configuration is displayed.
In addition to the default configuration, up to eight further configurations
can be loaded.
The selection of the configuration that has to be loaded can be made
between eight personalizable configurations and the default settings.
The selected configuration is will be immediately loaded and displayed in
the menu as Active. The previously active configuration is deleted.
OSD
1.
Select Configuration > Open in the main menu.
2.
Select the desired configuration.
3.
Load the configuration by pressing the key <Enter>.
Menu Configuration – Open...
142
2013-08-14
Configuration
Java Tool
1.
Select Administration > Activate Configuration during online-mode
in the task area
2.
Select the required configuration.
3.
Load the configuration by pressing the button Activate.
Menu Administration – Activate Configuration
Pos: 85 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
143
Draco tera
Pos: 86 /806-IHSE/Konfiguration/480_Speichern und Laden von Konfigurationen/480-xx/Speichern von Konfigurationen (extern) @ 7\mod_1309938846930_6.doc @ 53328 @ 3 @ 1
5.9.4
Saving of Configurations (external)
Created configurations can be saved as a file and so become independent
of the matrix and transportable.
You have the following possibility to access the menu:
1.
Select File > Save As in the menu bar.
2.
Enter a name for the configuration.
3.
Select the directory of the configuration on your storage medium
where it has to be saved.
Configurations are always saved in a file with the ending dtc.
Menu File – Save As
Pos: 87 /806-IHSE/Konfiguration/480_Speichern und Laden von Konfigurationen/480-xx/Laden von Konfigurationen (extern) @ 7\mod_1309938925211_6.doc @ 53364 @ 3 @ 1
144
2013-08-14
Configuration
5.9.5
Loading of Configurations (external)
Externally saved configurations are opened and activated in this menu.
You have the following possibilities to load configurations from files:
1.
Select File > Open… during offline-mode and select the storage
location of the configuration file that has to be opened.
2.
Open the configuration by pressing the button Open.
3.
Select File > Upload in the menu bar to transfer the opened
configuration to the matrix. Enter the necessary parameters.
4.
Select Matrix > Connect in the menu bar to make a connection
between the matrix and the Java tool. Enter the necessary
parameters.
5.
Select Administration > Activate Configuration and select the
configuration that has to be activated.
6.
Confirm the process with the button Activate.
The opened configuration is activated and can be used now.
Menu File – Open…
Pos: 88 /806-IHSE/Konfiguration/480_Export und Import von Listen/480-xx/Export und Import von Listen @ 7\mod_1309939181868_6.doc @ 53390 @ 2 @ 1
2013-08-14
145
Draco tera
5.10
Export and Import Options
The Draco tera offers the possibility to read out available configuration
lists (extender, CPUs, consoles and users) for exporting and importing
again via Java tool. You have the following possibilities to handle
configuration lists.
Exported configuration lists are always saved in .csv format that allows
offline editing with common spreadsheet applications.
You have the following possibilities to export or import configuration lists:
Pos: 89 /806-IHSE/Konfiguration/480_Export und Import von Listen/480-xx/Export von Listen @ 7\mod_1309939231696_6.doc @ 53408 @ 3 @ 1
5.10.1 Export Options
Configuration lists are exported in this menu. To export, proceed as
follows:
1.
Select File > Export in the menu bar.
2.
After opening the menu, select the list to export (Extender, CPU,
Console or User).
3.
Select the storage location for the export file.
4.
Confirm the export with the button Finish.
Menu File – Export
146
2013-08-14
Configuration
Pos: 90 /806-IHSE/Konfiguration/480_Export und Import von Listen/480-xx/Import von Listen @ 7\mod_1309939264649_6.doc @ 53426 @ 3 @ 1
5.10.2 Import Options
Configuration lists are imported in this menu. To import, proceed as
follows:
1.
Select File > Import in the menu bar.
2.
After opening the menu, select the list to import (Extender, CPU,
Console or User).
3.
Select the directory of the list to import.
4.
Confirm the import with the button Finish.
Menu File – Import...
Pos: 91 /806-IHSE/Konfiguration/480_Firmware Aktualisierung/480-xx/Firmware-Aktualisierung @ 7\mod_1313482000731_6.doc @ 54542 @ @ 1
2013-08-14
147
Draco tera
5.11
Firmware Update
5.11.1 Matrix Update
The firmware of the matrix can be updated in this menu.
You have the following possibility to access the menu:
Java Tool
Only use computers to update the matrix that are self-sustaining and not
integrated in the KVM extender / matrix setup.
Ensure that the computer used for the update is not set into stand by
mode or sleep mode during the update.
Ensure that your configuration has been saved externally before you will
start the update.
For reasons of network stability, an update via WLAN is not
recommended.
Preparation
Take the following steps in order to be prepared for the matrix update:
1.
Save the matrix configuration externally (see Chapter 5.9.4, Page
144).
2.
Open Extras > Options in the menu bar and insert in the setting
Firmware Directory the directory from which the update files should
be standardly sourced.
3.
Put all hot spare boards into the matrix.
4.
Activate the Syslog function (see Chapter 3.9, Page 38) for the
monitoring of the update, if unlocked via license key.
Ensure implicitly that all USB 2.0 extenders are only connected to the
provided ports (fixed ports) before you start the matrix update. A nonobservance will have a negative influence on the stability of the update.
148
2013-08-14
Configuration
Performing the Update
Take the following steps in order to be prepared for the matrix update:
1.
Select Administration > Update Matrix Firmware in the task area.
All updateable components of the matrix will be automatically
selected and highlighted in green.
Menu Administration – Update Matrix Firmware
2.
Start the update by pressing the button Update in the appearing
pop up window.
3.
Restart the Matrix after the update by pressing the button Restart
matrix in the lower part of the working area.
For a safe initialisation of the matrix, a cold start (power cycle) is
recommended.
2013-08-14
149
Draco tera
5.11.2 Extender Update
The firmware of the extenders connected to the matrix can be updated in
this menu.
You have the following possibilities to access the menu:
Preparation
Take the following steps in order to be prepared for the extender update:
1.
Save the matrix configuration externally (see Chapter 5.9.4, Page
144).
Open Extras > Options in the menu bar and insert in the setting
Firmware Directory the directory from which the update files should
be standardly sourced.
2.
Connect all hot spare extenders to the matrix.
For reasons of network stability, an update via WLAN is not
recommended.
150
2013-08-14
Configuration
Performing the Update in Standard Mode (parallel Update)
1.
Select Administration > Update EXT Firmware in the task area. The
standard mode for the parallel update will be selected by default and
the tab Upload Firmware will be opened.
Menu Administration – Update EXT Firmware
2.
Before the actual update process, all firmware files have to be
uploaded to the respective I/O boards on that extenders will have to
be updated. By selecting the update files, the I/O boards will be
automatically chosen for the upload in the column Selected and
highlighted in green, but only if a newer firmware version is selected.
3.
Start the upload and distribution of the update files by pressing the
button Upload.
By performing the upload process, no update files will be installed. the
update process can be performed at a later time.
If there are not selected all I/O cards, the upload of the update files will be
performed in sequence.
2013-08-14
151
Draco tera
4.
After finishing the upload process the successful completion will be
confirmed by a popup. If you want to directly start the actual update
process, you will have to confirm this by pressing the button Yes. You
will be immediately forwarded to the tab Update Firmware.
When updating an identical or an older firmware version as the version
that is currently installed, the option Force Update in the lower part of the
working area has to be enabled.
Menu Administration – Update EXT Firmware
5.
Start the actual update process by pressing the button Update.
Just before the update process, all affected I/O boards will be set into
Service Mode and retrieved gradually after finishing the respective
updates.
152
2013-08-14
Configuration
Performing the Update in Expert Mode (sequential Update)
Take the following steps in order to be prepared for the extender update:
1.
Select Administration > Update EXT Firmware and select Expert
Mode in the upper part of the working area. All updateable extenders
will be automatically selected and highlights in green.
Menu Administration – Update EXT Firmware
2.
Set the matrix into Service Mode upon request in the popup window
or via Matrix > Activate Service Mode in the menu bar.
During activation, all matrix functions are disabled on the I/O boards
on which an update is currently performed. An OSD picture indicates
the activation of the Service Mode and is displayed on all monitors
that are connected to the matrix via a CON device. Additionally, the
Service Mode is indicated by a red tool icon in the lower part of the
working area.
2013-08-14
153
Draco tera
OSD View Service Mode
3.
Start the update by pressing the button Update in the lower part of
the working area.
4.
Quit Service Mode after updating upon request in the popup window
or via Matrix > Deactivate Service Mode in the task area.
5.
Verify after the update in the Java tool via Administration > Update
EXT Firmware in the tab Protocol of the Expert Mode, if the
updates for all extenders have been installed correctly.
Pos: 92 /806-IHSE/Konfiguration/480_Lizenzmanagement/480-xx @ 8\mod_1352795644169_6.doc @ 69622 @ 2 @ 4
5.12
License Management
In this menu the matrix can be upgraded with new function bundles by
using license keys.
In order to get license keys to upgrade matrix functions, contact your
distributor.
You have the following possibility to access the menu:
154
2013-08-14
Configuration
Java Tool
In order to activate a function bundle, proceed as follows:
1.
Select Administration > License Management in the task area.
Menu Administration – License Management
2.
Enter your license key in the working area under Activate Bundles in
the field License Key.
3.
In order to activate the license key press the button Activate. The
new functions will be immediately enabled, a restart of the matrix will
not be necessary.
Pos: 93 /806-IHSE/Betrieb/UEB_Betrieb @ 5\mod_1278577614980_6.doc @ 41970 @ 1 @ 1
2013-08-14
155
Draco tera
6
Operation
Pos: 94 /806-IHSE/Betrieb/480-xx @ 7\mod_1309939496086_6.doc @ 53444 @ @ 1
The Draco tera can be operated in three different ways:
1. Direct Switching

via a keyboard connected to a CON port and the favorites

by a macro keyboard connected to a console port
2. OSD

via keyboard/mouse directly connected to the CPU board of the
matrix

via keyboard/mouse connected to a CON Unit and the OSD
3. External Switching Commands:

via an external computer via Java tool (network connection required)

via a media control (network or serial connection required)
Pos: 95 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
156
2013-08-14
Operation
Pos: 96 /806-IHSE/Betrieb/Bedienung über HotKeys/480-xx/UEB_Bedienung_über_Hotkeys @ 7\mod_1309939558243_6.doc @ 53464 @ 2 @ 1
6.1
Operation via 'Hot Keys'
Pos: 97 /806-IHSE/Betrieb/Bedienung über HotKeys/480-xx/Direktumschaltung @ 7\mod_1309940339211_6.doc @ 53490 @ 3 @ 1
6.1.1
Direct Switching
The direct switching by favorites on a keyboard is the fastest possibility for
a user to switch at his console between different CPUs. There is a
possibility to switch video, keyboard and mouse or only video.
Direct Switching of Video, Keyboard and Mouse
1.
Start Command Mode with the 'Hot Key'.
For control, the LEDs Shift and Scroll flash at the keyboard, if
Command Mode is activated.
2.
Enter the index number of the new CPU from the list of favorites and
confirm with <Enter>.
At the same time the Command Mode is closed and the console is
connected to the new CPU with complete control.
Example: Switching to favourite CPU 7 with video, keyboard and mouse
<left Shift>, <left Shift>, <7>, <Enter>
Best results regarding switching time can be achieved by using identical
mice, keyboards and monitors. This contributes to a smooth and seamless
direct switching of the matrix.
Switching in Private Mode
1.
Start Command Mode with the 'Hot Key'.
For control, the LEDs Shift and Scroll flashes at the keyboard, if
command mode is activated.
2.
Enter the index number of the new CPU from the list of favorites and
confirm with <left Shift>, <Enter> pressed at the same time.
At the same time the Command Mode is closed and the console is
connected to the new CPU with complete control in Private Mode.
Example: Switching to favorite CPU 3 in Private Mode
<left Shift>, <left Shift>, <3>, <left Shift>, <Enter>
2013-08-14
157
Draco tera
Direct Switching of Video
1.
Start Command Mode with the 'Hot Key'.
For control, the LEDs Shift and Scroll flashes at the keyboard, if
command mode is activated.
2.
Enter the index number of the new CPU from the list of favorites and
confirm with <Space>.
At the same time the Command Mode is closed and the console is
connected to the new CPU with video only.
Example: Switching to favourite CPU 1 with video only
<left Shift>, <left Shift>, <1>, <Space>
Switch to previous CPU
1.
Start Command Mode with the 'Hot Key'.
For control, the LEDs Shift and Scroll flash at the keyboard, if
Command Mode is activated.
2.
Press the key <p> of your keyboard.
At the same time the Command Mode is closed and the console is
connected to the previous CPU with complete control.
If you switch to a previous CPU that was connected with Video Access
before, you will be connected to this CPU with full KVM access.
You can only switch to not used and allowed CPUs with the 'Hot Keys'.
The options Force Connect and Force Disconnect as well as the
restrictions of the User ACL and CON ACL are taken into account.
'Hot Keys' are only supported, if neither Enable User Login nor the
Enable User ACL is selected and the user is logged in the OSD.
Disconnect current Connection
1.
Start Command Mode with the 'Hot Key'.
For control, the LEDs Shift and Scroll flash at the keyboard, if
Command Mode is activated.
2.
Press the key <Backspace> of your keyboard.
The Command Mode is closed and the console is disconnected from
the previous connected CPU.
Pos: 98 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
158
2013-08-14
Operation
Pos: 99 /806-IHSE/Betrieb/Bedienung über HotKeys/480-xx/Scan-Modus @ 7\mod_1309940746290_6.doc @ 53508 @ 3 @ 1
6.1.2
Scan Mode
The Scan Mode offers the possibility to show video signals of the different
CPU favorites fast and without delay and offers switching in between
without continuously using the 'Hot Key'. The switching between two video
signals can even take place within one frame.
1.
Start command mode with the 'Hot Key'. For control, the LEDs Shift
and Scroll flashes at the keyboard, if command mode is activated.
2.
Press the key <Left Shift> and hold it down. You can now enter the
index numbers of the various CPUs from the list of favorites with the
keyboard and immediately switch to the video signal of the respective
CPU after entering the index number.
3.
Leave Scan Mode by pressing <Left Shift> + <Esc>.
Optimal results can be achieved by the use of as identical resolutions as
possible. This contributes to a smooth and seamless function of the scan
mode.
Pos: 100 /806-IHSE/Betrieb/Bedienung über HotKeys/480-xx/Funktionstasten <F1> - <F16> @ 7\mod_1309940812665_6.doc @ 53544 @ 3 @ 1
6.1.3
Function Keys <F1>–<F16>
In Command Mode you can retrieve the macros 1–16 with the function
keys <F1>–<F16> of the connected standard keyboard instead of the
special macro keyboard.
The deposited command sequence for the appropriate function key is
executed and Command Mode is left immediately.
Regarding macros there is no necessity of using the key <Enter> for
confirmation.
Pos: 101 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
159
Draco tera
Pos: 102 /806-IHSE/Betrieb/Bedienung über HotKeys/480-xx/Adressierung von Main-Matrix und Sub-Matrix @ 7\mod_1309940780680_6.doc @ 53526 @ 3 @ 1
6.1.4
Addressing of Main and Sub Matrices
The Draco tera can be cascaded in two steps. You can optionally send the
commands (including opening the OSD) to the main or the sub matrix.
Whenever command mode is activated, you can select by a <m> or a <s>,
if all of the following commands should be handled in the main or in the
sub matrix.
OSD Access

OSD access to the main matrix:
<Left Shift>, <Left Shift>, <m> (optional), <o>

OSD access to the sub matrix:
<Left Shift>, <Left Shift>, <s>, <o>
Example: Switching to the CPU port 23 of the sub matrix.
1.
Switching to the CPU Port (e.g. 12) of the master matrix that have the
connection to the sub matrix:
<Left Shift>, <Left Shift>, <1>, <2>, <Enter>
2.
Switching to the CPU Port 23 of the sub matrix:
<Left Shift>, <Left Shift>, <s>, <2>, <3>, <Enter>
The selected main matrix / sub matrix mode is permanently activated until
the other mode will be manually activated. This means that if you
select <s> for example, all prospective commands will be sent to the
slave, but not if the Command Mode is left in the meantime.
Pos: 103 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
160
2013-08-14
Operation
Pos: 104 /806-IHSE/Betrieb/KVM-Schaltung/480-xx @ 7\mod_1309940863555_6.doc @ 53563 @ 22 @ 1
6.2
KVM-Switching
You have the following possibilities to perform switching operations with
the Draco tera:
OSD
 Select Switch in the main menu.
By pressing the key <F8>, inactive CPU devices can be hidden in order to
ensure a better overview.
Menu Switch
To switch the own console to any available CPU, proceed as follows:
1.
Select in the list CPU Devices on the left side that one that should be
connected to the own CON device.
2.
Confirm with the respective keyboard command according to the
desired connection type.
2013-08-14
161
Draco tera
Switching operations from the own CON device can only be done to
CPU devices that are available in the list CPU Devices.
Listed CPU devices highlighted in red color are currently connected in
Private Mode and are blocked by the connected CON device.
Switching via Selection List for CPU Devices
The matrix offers the possibility to execute KVM switching operations by a
selection list for CPU devices next to the OSD in full screen.
In order to use the selection list for CPU Devices, proceed as follows:
1.
Activate the option Enable CPU Selection in the menu
Configuration for those consoles where the selection list for CPU
devices should be available.
2.
Execute the key sequence for opening the OSD. The selection list
immediately appears in the preset position of the extender OSD.
By pressing the key <F8>, inactive CPU Devices can be hidden to ensure
a better overview.
3.
162
Execute the desired switching operation by pressing the respective
key (see Chapter 6.3, Page 164).
In order to not execute a switching operation and access OSD, press
the key <F7>.
In order to close the selection list, press the key <Esc>.
2013-08-14
Operation
Example view Selection list CPU Devices
Activating the automatical Scan Mode for CPU Devices
The matrix offers the possibility to use a scan mode based on the favorite
list of each console or user. The scan mode allows the matrix to switch in
sequence between the CPU Devices in the favorite list within a predefined
time. All scans are performed in video only mode.
For a configuration of the scan mode, Chapter 5.8.1, Page 115.
You have the following possibility to activate the scan mode:
In order to activate the scan mode, proceed as follows:
1.
Define a favorite list for the respective CON Device or user (see
Chapter 5.8.4, Page 126 for CON Devices or see Chapter 5.5.2,
Page 100 for users)
2.
Start Command Mode with the 'Hot Key' and press <o> to open OSD.
3.
Select in the CPU selection list one of the CPU Devices that are
defined in your favorite list.
2013-08-14
163
Draco tera
6.3
4.
Confirm your selection by pressing the button CPU Scanner. The
scan will automatically start.
5.
If you have enabled the option Force CPU Scan, the scan will
automatically start after switching the respective CON Device to any
CPU Device from the favorite list without the need to press the button
CPU Scanner.
Extended Switching
You have the following possibilities to perform switching operation with the
Draco tera:
OSD
To switch any console to any available CPU, proceed as follows:
 Select Extended Switch in the main menu.
By pressing the key <F8>, inactive CPU Devices can be hidden to ensure
a better overview.
Menu Extended Switch
164
2013-08-14
Operation
1.
Select in the list CON Devices on the left side that one that should be
switched to a CPU device and open it by pressing <Enter>.
2.
Select in the list CPU Devices on the left side that one that should be
connected to the open CON device.
3.
Confirm with the respective keyboard command according to the
desired connection type.
Switching operations from the own CON device can only be done to CPU
devices that are available in the list CPU Devices.
The following information is shown in this menu:
Field
Description
CON device
Assigned physical extender unit (CON unit)
CON assigned
Virtual CON Device that is assigned to the real
CON device
CPU connected Currently connected CPU device
CON status
Current connection status (CON device)
EXT list
List of all available physical extender units
(CON units)
CPU device
Assigned physical extender unit (CPU unit)
CPU assigned
Real CPU device that is assigned to a virtual
CPU device
CON
connected
Currently connected CON device
CPU status
Current connection status (CPU device)
EXT list
List of all available physical extender units
(CPU units)
You can select between the following switching functions:
Function
Keyboard Command
Set a video only connection.
<Space>
Set a KVM connection.
<Enter>
Set a KVM connection in private mode (video
sharing disabled).
<Shift> + <Enter>
Disconnect own CON device from CPU device.
<Backspace>
2013-08-14
165
Draco tera
Java Tool
You have two possibilities to perform switching operations for the Draco
tera via Java Tool:
Possibility 1:
 Select Control > Extended Switch in the task area.
Menu Control – Extended Switch
All connected consoles and the associated CPU connections are shown in
columns in the working area in this menu.
Switching operations can only be performed in online mode. That means
an active network connection between the matrix and the Java Tool is
required.
 In order to set a KVM connection between a console and a CPU,
double-click on the corresponding selection box within the column
Full Access and select the requested CPU.
 In order to set a video connection between a console and a CPU,
double-click on the corresponding selection box within the column
Video Only and select the requested CPU.
 In order to set a Private Mode connection between a console and a
CPU, double-click on the corresponding selection box within the
column Private Mode and select the requested CPU.
166
2013-08-14
Operation
CPUs whose respective console does not have access rights, will not
appear in the list.
The following symbols are shown in the connection overview:
Symbol
Description
CON device is connected via Shared Access with at
least one further console to the same CPU. The CON
device has Full Access at the moment.
CON device is connected via Shared Access with at
least one further console to the same CPU. The CON
device has a Video Access connection at the
moment.
You can use the following button to perform a switching operation:
Button
Function
Send
Send effected switching operations to the matrix
Reset
Disconnect all existing connections within the matrix
Reload
Reload switching status
When activating the function Auto Send in the left lower corner of the
working area, switching operations will be done immediately without
confirmation by pressing the button Send.
When activating the function Hide Devices w/o Extender Assignment in
the left lower corner of the working area, only these CON and CPU
devices are shown that are assigned to an extender.
2013-08-14
167
Draco tera
Possibility 2:
 Select Status > Matrix View in the task area.
Menu Status – Matrix View
In order to perform switching operations between CON and CPU devices
proceed as follows:
1.
Move the mouse cursor to the port that has to be switched.
2.
Hold down the left mouse button and move the cursor to the port that
has to be connected to the initial port. The current cursor movement
will be displayed by a black auxiliary line.
3.
Release the left mouse button. A popup to select the available
switching type (Full Access, Video Access or Private Mode) will be
opened.
4.
Select the desired switching type. The switching operation will be
immediately executed. At the same time all extender units that are
assigned to the involved devices will be switched.
If there is a red cross on a port when switching by using the Matrix View,
the console to be connected does not have access rights to the respecting
CPU at this port.
168
2013-08-14
Operation
In order to disconnect existing connection between CON and CPU devices
proceed as follows:
1.
Click on the port that has to be disconnected by using the right mouse
button.
2.
Select the function Disconnect in the appearing popup. The
connected ports will be immediately disconnected. At the same time
all further connections of the extenders assigned to the involved
devices will be disconnected.
Pos: 105 /806-IHSE/Betrieb/480_CON Switch/480_CON Switch @ 9\mod_1375172364133_6.doc @ 79232 @ 2 @ 4
6.4
CON Switch
KVM extender CON Units connected to a local source (computer, CPU)
can be locally switched via the matrix. Switching is performed between the
local source and the KVM connection and can be executed via 'Hot Keys'
or via OSD.
If you switch to the local source, the KVM connection will be automatically
disconnected.
You have the following possibility to switch to the local source:
2013-08-14
169
Draco tera
OSD
 Select Switch in the main menu.
Menu – CON Switch
In order to switch to a local source, proceed as follows:
1.
If you are not yet in the menu Switch of the OSD, start Command
Mode with the 'Hot Key' (see Chapter 5.1, Page 53).
2.
Press <o> to open OSD.
You will see a list of all available CPUs as a start menu.
3.
Switch to the CPU in the list that is called Local CPU.
The switching operation to the local source will be immediately
performed.
The local source (computer, CPU) will be only shown in the OSD, if the
respecitve CON Unit includes the option for a local connection.
170
2013-08-14
Operation
Alternatively, there are the following keyboard commands available in
order to switch to the local source:
Function
Keyboard Command
Switching to extender connection
<'Hot Key'>, <k>, <1>, <Enter>
Switching to extender connection 2
(only with redundant CON Units)
<'Hot Key'>, <k>, <2>, <Enter>
Switching to the local source
(computer, CPU)
<'Hot Key'>, <l>, <Enter>
Pos: 106 /806-IHSE/Betrieb/480_Multi-Screen_Kontrolle/480_Multi-Screen-Kontrolle @ 8\mod_1360600488238_6.doc @ 71072 @ 2 @ 1
6.5
Multi-Screen Control
The function Multi-Screen contains a switching of the USB-HID signal
between different statically connected sources (computer, CPU) within a
CON Device and can be performed in two different ways:
Switching via Mouse
The switching of the USB-HID signal can be made by a movement of the
mouse pointer beyond the edge of the current display to a neighboring
display according to the configuration (see Chapter 5.8.7, Page 135).
In order to perform a switching operation via movement of the mouse
pointer, proceed as follows:
1.
Move the mouse pointer to that edge of the display which borders
vertically or horizontally to the neighboring display.
2.
Move the mouse pointer beyond the edge of the display. The mouse
pointer will appear on the respective position at the target display.
The switching operation has been performed and the USB-HID signal
will be now available at the target display.
Switching via Keyboard
The switching of the USB-HID signal can be made by the use of keyboard
commands next to the mouse movement (configuration see Chapter 5.8.7,
Page 135).
2013-08-14
171
Draco tera
In order to perform a switching operation via keyboard command, proceed
as follows:
1.
Start Command Mode with the 'Hot Key' (see Chapter 5.1, Page 53).
2.
Select the target display by pressing the respective key on the
numeric pad of the keyboard.
The switching operation will be performed and the USB-HID signal
will be available at the target display.
You can select between the following switching operations:
Keyboard Command
Function
<current 'Hot Key'>,
<Num 0>
Switching of the USB-HID signal to the own
display (CON Unit with keyboard and mouse)
<current 'Hot Key'>,
<Num 1>
Switching of the USB-HID signals to display #1
<current 'Hot Key'>,
<Num 2>
Switching of the USB-HID signals to display #2
<current 'Hot Key'>,
<Num 3>
Switching of the USB-HID signals to display #3
<current 'Hot Key'>,
<Num 4>
Switching of the USB-HID signals to display #4
Pos: 107 /806-IHSE/Betrieb/USB-2.0-Umschaltung/480_USB-2.0-Umschaltung @ 8\mod_1345794455672_6.doc @ 68043 @ 2 @ 1
6.6
USB 2.0 Switching
Switching of USB 2.0 extender basically works like switching of KVM
extenders. The following scenarios to switch USB 2.0 extenders are
possible.
1.
A extender unit with USB 2.0 will be created and assigned so an
already existing device with existing KVM extender units (see Chapter
5.7, Page 111 or Chapter 5.8.1, Page 115).
2.
A separate device for the extender unit with USB 2.0 will be created
without assigning a KVM extender unit to that device. This possibility
offers a separate switching of the USB 2.0 signal (see Chapter 5.7,
Page 111 or Chapter 5.8.1, Page 115).
The separate switching of USB 2.0 signals required the use of the
possibilities that extended switching offers (see Chapter 6.3, Page 164).
When switching USB 2.0 connections you should wait until the process of
registration of the USB 2.0 devices has been completed before you switch
to the next CPU (ca. 5-15 s). Otherwise the stability of the USB 2.0
connection can be affected negatively.
172
2013-08-14
Operation
Pos: 108 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
Pos: 109 /806-IHSE/Betrieb/Schaltmakros/480-xx @ 7\mod_1324449399385_6.doc @ 56882 @ 2 @ 1
6.7
Presets
Predefined macros to switch the matrix without loading a new
configuration can be created and activated in this menu.
You have the following possibility to access the menu:
 Select Control > Presets in the task area.
Menu Control – Presets
To create a new switch macro proceed as follows:
1.
Open a new switch macro by pressing on the symbol New in the right
column of the working area.
You are asked if the existing connections shall be taken over for the
new switch macro.
2.
2013-08-14
Set the desired switching operations in the corresponding columns
(Full Access, Video Only or Private Mode) by using a double click
on the respective selection box or use the function for a disconnect
(Disconnect CPU).
173
Draco tera
3.
Save the created switch macro by clicking the symbol Save in the
right column of the working area.
A save dialog will be opened.
4.
Enter a name or the new switch macro and confirm by pressing the
button Ok in the save dialog.
5.
By clicking on a selected switch macro with the right mouse button,
you can create a copy of the current switch macro when using the
option Save as....
6.
Already saved macros can be deleted by pressing the symbol Delete.
To load a predefined switching, proceed as follows:
1.
Select the switch macro in the right column of the working area that
has to be loaded.
2.
Activate the selected switch macro by pressing the button Send on
the bottom right of the working area.
A predefined switch macro can only be activated in online mode.
When loading presets, only these switching operations are taken into
account that are compliant with the hardware and the configuration of the
currently used matrix.
Pos: 110 /806-IHSE/Betrieb/Serielle Schnittstellen/480-xx @ 7\mod_1309940914961_6.doc @ 53582 @ 2 @ 1
6.8
Serial Interface
The Draco tera offers the possibility to switch via a serial interface
(RS232).
Detailed information for the serial interface and the corresponding
switching commands are available in form of an API (application
programming interface) upon request.
Pos: 111 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
174
2013-08-14
Operation
Pos: 112 /806-IHSE/Betrieb/Ein- und Ausschaltfunktionen/UEB_Ein-_und_Ausschaltfunktionen @ 7\mod_1309940964258_6.doc @ 53601 @ 2 @ 1
6.9
Power On and Power Down Functions
Pos: 113 /806-IHSE/Betrieb/Ein- und Ausschaltfunktionen/480-xx/Neustart @ 7\mod_1309941015165_6.doc @ 53620 @ 3 @ 1
6.9.1
Restart
You have the following possibilities to perform a restart:
OSD
1.
Select Configuration > Restart Matrix or Restart IO Board in the
main menu to restart either the matrix or the I/O boards.
2.
Confirm the selection with button Okay.
The matrix and the I/O boards will be restarted with the current settings.
Java Tool
 Select Matrix > Restart Matrix in the menu bar.
The matrix will be restarted with the current settings.
The boot process of the matrix might take longer, if there is no physical
network connection available.
Pos: 114 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
175
Draco tera
Pos: 115 /806-IHSE/Betrieb/Ein- und Ausschaltfunktionen/480-xx/Factory Reset @ 7\mod_1309941081774_6.doc @ 53638 @ 3 @ 1
6.9.2
Factory Reset
You have the following possibilities to perform a reset of the system:
If you do a (factory) reset, all current settings and all configurations stored
in the matrix will be lost. This also applies to the network parameters
(reset to DHCP) and the admin password.
If a firmware update has been done since the delivery, the matrix will be
set to the state defined there.
OSD
1.
Select Configuration > Factory Reset in the main menu.
2.
Confirm the selection with the button Okay.
The matrix will be reset to factory settings.
Pos: 116 /806-IHSE/Betrieb/Ein- und Ausschaltfunktionen/480-xx/480_Ausschalten @ 7\mod_1310646450471_6.doc @ 54300 @ 3 @ 1
6.9.3
Power Down
You have the following possibilities to perform a shut down of the system
or single components:
OSD
In order to shut down the system, proceed as follows:
1.
Select Configuration > Shut down Matrix in the main menu.
2.
Confirm the selection with the button Okay.
The matrix will be shut down.
In order to shut down an I/O board, proceed as followsr:
1.
Select Configuration > Shut Down IO Board in the main menu.
2.
Confirm the selection with the button Okay.
The I/O board will be shut down.
Pos: 117 /806-IHSE/Betrieb/480_Zusammenfassung Tastaturkommandos/480_Zusammenfassung Tastatur Kommandos @ 9\mod_1360601486169_6.doc @ 71092 @ 2 @ 1
176
2013-08-14
Operation
6.10
Summary of Keyboard Commands
In the following you find a summary of keyboard commands that can
activate extender and matrix functions after executing the 'Hot Key'.
Extender
Keyboard Command
Description
<'Hot Key'>, <a>
Download of DDC information of the monitor
connected to the CON Unit into the CPU Unit
<'Hot Key'>, <k>, <1>,
<Enter>
Switch to the KVM connection (only with HDMI
CON Units with available connection for a local
source)
<'Hot Key'>, <k>, <2>,
<Enter>
Switch to the KVM connection 2 (only with
HDMI CON Units with available connection for
a local source and a redundant
interconnection)
<'Hot Key'>, <l>,
<Enter>
Switch to local source (computer, CPU) (only
with HDMI CON Units with available
connection for a local source)
<'Hot Key'>, <h>, <w>,
<Enter>
USB-HID Ghosting: Writing the device
descriptions of the input devices connected to
the CON Unit into the CPU Unit. Activating the
emulation in the CPU Unit.
<'Hot Key'>, <h>, <e>,
<Enter>
Activating the emulation of already stored
device descriptions in the CPU Unit
<'Hot Key', <h>, <d>,
<Enter>
Deactivating the emulation of active device
descriptions in the CPU Unit. The input devices
connected to the CON Unit will be now passed
transparently to the source (computer, CPU).
<'Hot Key', <h>, <r>,
<Enter>
Deactivating the emulation of active device
descriptions in the CPU Unit. Deleting the
descriptions out of the CPU Unit. The input
devices connected to the CON Unit will be now
passed transparently to the source (computer,
CPU).
Matrix
Keyboard Command
Description
<'Hot Key'>, <o>
Open OSD
<‘Hot Key‘>, <m>, <o>
Open OSD of the master matrix in a cascaded
environment
2013-08-14
177
Draco tera
Keyboard Command
Description
<‘Hot Key‘>, <s>, <o>
Open OSD of the sub matrix in a cascaded
environment
<'Hot Key'>, <Enter>
Set a KVM connection (keyboard, mouse and
video) to the selected source (computer, CPU)
<'Hot Key'>, <Space>
Set a video only connection to the selected
source (computer, CPU)
<'Hot Key'>, <Left
Shift> + <Enter>
Set a Private Mode connection to the selected
source (computer, CPU)
<'Hot Key'>,
<Backspace>
Close the current connection of the own
console
<'Hot Key'>, <p>
Switch back to the previous connected source
(computer, CPU) with a KVM connection
<'Hot Key'>, <1> ...
<16>, <Enter>
(<Space> or <Left
Shift> + <Enter>)
Switch to a source (computer, CPU) stored in
the Favorite List with a KVM connection (video
only or Private-Mode connection)
<'Hot Key'>, <F1> ...
<F16>
Execute a predefined macro
<'Hot Key'>, <c>, <new Change the 'Hot Key' according to the
'Hot Key'-Code>,
predefined 'Hot Key' table
<Enter>
<'Hot Key'>, <c>, <0>,
<new 'Hot Key' key >,
<Enter>
Define freely selectable 'Hot Key'
<'Hot Key'>, <f>, <new
'Hot Key'-Code>,
<Enter>
Change the 'Hot Key' for direct OSD access
according to the predefined 'Hot Key' table
<'Hot Key'>, <f>, <0>,
<new 'Hot Key' key>,
<Enter>
Define freely selectable 'Hot Key' for direct
OSD access
<'Hot Key'>, <Num 0>
Switching of the USB-HID signal to the own
display (CON Unit with keyboard and mouse)
<'Hot Key'>, <Num 1>
Switching of the USB-HID signals to display #1
<'Hot Key'>, <Num 2>
Switching of the USB-HID signals to display #2
<'Hot Key'>, <Num 3>
Switching of the USB-HID signals to display #3
<'Hot Key'>, <Num 4>
Switching of the USB-HID signals to display #4
Pos: 118 /806-IHSE/Technische Daten/UEB_Technische Daten @ 5\mod_1278578165261_6.doc @ 42096 @ 1 @ 1
178
2013-08-14
Specifications
7
Specifications
Pos: 119 /806-IHSE/Technische Daten/Schnittstellen/UEB_Schnittstellen @ 5\mod_1278578201870_6.doc @ 42114 @ 2 @ 1
7.1
Interfaces
Pos: 120 /806-IHSE/Technische Daten/Schnittstellen/DVI-D-Single-Link @ 5\mod_1278578254058_6.doc @ 42132 @ 3 @ 1
7.1.1
DVI-D Single Link
The video interface supports the DVI-D protocol. All signals that comply to
DVI-D Single Link norm can be transmitted. This includes e.g. monitor
resolutions such as 1920x1200@60Hz, Full HD (1080p) or 2K HD (up to
2048x1152). Data rate is limited to 165 MPixel/s.
Pos: 121 /806-IHSE/Technische Daten/Schnittstellen/USB-HID @ 5\mod_1278578292214_6.doc @ 42150 @ 3 @ 1
7.1.2
USB-HID
Our devices with USB-HID interface support a maximum of two devices
with USB-HID protocol. Each USB-HID port provides a maximum current
of 100 mA.
Keyboard
Compatible with most USB keyboards. Certain keyboards with additional
functions may require custom firmware to operate. Keyboards with an
integral USB Hub (Mac keyboards e.g.) are also supported.
Mouse
Compatible with most 2-button, 3-button and scroll mice.
Other USB-HID devices
The proprietary USB emulation also supports certain other USB-HID
devices, such as specific touch screens, graphic tablets, barcode
scanners or special keyboards. Support cannot be guaranteed, however,
for every USB-HID device.
Only two USB-HID devices are supported concurrently, such as keyboard
and mouse or keyboard and touch screen. A hub is allowed, but it does
not increase the number of HID devices allowed.
To support other USB 'non-HID' devices, such as scanners, web cams or
memory devices, choose our devices with transparent USB support.
Pos: 122 /806-IHSE/Technische Daten/Schnittstellen/RJ45 (Netzwerk) @ 7\mod_1309942049133_6.doc @ 53692 @ 3 @ 1
2013-08-14
179
Draco tera
7.1.3
RJ45 (Network)
The communication of the Cat X devices requires a 1000BASE-T
connection.
The cabling has to be done according to EIA/TIA-568-B (1000BASE-T)
with RJ45 connectors at both ends. All of the four wire pairs are used in
both directions. The cabling is suitable for a full duplex operation. For the
cable connection to a source (computer, CPU), a crossed network cable
(cross cable) has to be used.
Pos: 123 /806-IHSE/Technische Daten/Schnittstellen/RS-232 (seriell) @ 7\mod_1309942120758_6.doc @ 53710 @ 3 @ 1
7.1.4
RS-232 (Serial)
The communication takes place with a transmission speed of up to
115.2 KBaud, regardless of the file format. The transmission takes place
with eight data bits and a stop bit, but without a parity bit. Limited
hardware handshake (DSR) is possible.
Pos: 124 /806-IHSE/Technische Daten/Schnittstellen/RJ45 (Gerätekommunikation) @ 5\mod_1278578339308_6.doc @ 42186 @ 3 @ 1
7.1.5
RJ45 (Interconnect)
The communication of the Cat X devices requires a 1000BASE-T
connection.
Connector wiring must comply with EIA/TIA-568-B (1000BASE-T), with
RJ45 connectors at both ends. All four cable wire pairs are used.
Pos: 125 /806-IHSE/Technische Daten/Schnittstellen/Glasfaser SFP Typ LC @ 5\mod_1278937700855_6.doc @ 43149 @ 3 @ 1
7.1.6
Fiber SFP Type LC (Interconnect)
The communication of fiber devices is performed via Gigabit SFPs that
have to be connected to suitable fibers fitted with connectors type LC (see
Chapter 7.2.2, Page 182).
The correct function of the device can only be guaranteed with SFPs
provided by the manufacturer.
SFP modules can be damaged by electrostatic discharge (ESD).
 Please consider ESD handling specifications.
Pos: 126 /806-IHSE/Technische Daten/Schnittstellen/SDI (Gerätekommunikation) @ 7\mod_1309941998461_6.doc @ 53674 @ 3 @ 1
180
2013-08-14
Specifications
7.1.7
SDI (Interconnect)
The communication of the SDI devices requires a mini coax connection
with mini BNC connectors or 3G SFPs with transmission speeds of
0,360 Gbit/s (SD-SDI, SMPTE 259M), 1,485 Gbit/s (HD-SDI,
SMPTE 292M) and 2,970 Gbit/s (3G SDI).
Pos: 127 /806-IHSE/Technische Daten/Verbindungskabel/UEB_Verbindungskabel @ 5\mod_1279191107845_6.doc @ 43870 @ 2 @ 1
7.2
Interconnect Cable
Pos: 128 /806-IHSE/Technische Daten/Verbindungskabel/Verbindungskabel (Cat X) @ 5\mod_1278578406026_6.doc @ 42205 @ 3 @ 1
7.2.1
Cat X
A point-to-point connection is required. Operation with several patch fields
is possible. Routing over an active network component, such as an
Ethernet Hub, Router or Matrix, is not allowed.
 Avoid routing Cat X cables along power cables.
 If the site has 3-phase AC power, try to ensure that CPU Unit and
CON Unit are on the same phase.
To maintain regulatory EMC compliance, correctly installed shielded Cat X
cable must be used throughout the interconnection link.
To maintain regulatory EMC compliance, all Cat X cables need to carry
ferrites on both cable ends close to the device.
Type of Interconnect Cable
The Draco tera requires interconnect cabling specified for Gigabit Ethernet
(1000BASE-T). The use of solid-core (AWG24), shielded, Cat 5e (or
better) is recommended.
Cat X Solid-Core Cable
AWG24
S/UTP (Cat 5e) cable according to EIA/TIA568-B. Four pairs of wires AWG24.
Connection according to EIA/TIA-568-B
(1000BASE-T).
Cat X Patch Cable
AWG26/8
S/UTP (Cat 5e) cable according to EIA/TIA568-B. Four pairs of wires AWG26/8.
Connection according to EIA/TIA-568-B
(1000BASE-T).
The use of flexible cables (patch cables) type AWG26/8 is possible,
however the maximum possible extension distance is halved.
Pos: 129 /806-IHSE/Technische Daten/Verbindungskabel/Verbindungskabel (Cat X)_Kabellänge 477-xx @ 5\mod_1278937761105_6.doc @ 43167 @ @ 1
2013-08-14
181
Draco tera
Maximum Acceptable Cable Length
Cat X Installation Cable
AWG24
140 m (400 ft)
Cat X Patch Cable
AWG26/8
70 m (200 ft)
Pos: 130 /806-IHSE/Technische Daten/Verbindungskabel/480-xx/Glasfaser @ 7\mod_1309942335305_6.doc @ 53729 @ 3 @ 1
7.2.2
Fiber
A point-to-point connection is necessary. Operation with multiple patch
panels is allowed. Routing over active network components, such as
Ethernet Hubs, Matrixes or Routers, is not allowed.
Type of Interconnect Cable
(Cable notations according to VDE)
Type of cable
Specifications
Single-mode 9μm





Two fibers 9μm
I-V(ZN)H 2E9 (in-house patch cable)
I-V(ZN)HH 2E9 (in-house breakout
cable)
I/AD(ZN)H 4E9 (in-house or outdoor
breakout cable, resistant)
A/DQ(ZN)B2Y 4G9 (outdoor cable, with
protection against rodents)
Multi-mode 50μm



Two fibers 50μm
I-V(ZN)H 2G50 (in-house patch cable)
I/AD(ZN)H 4G50 (in-house or outdoor
breakout cable, resistant)
Multi-mode 62.5μm


Two fibers 62.5μm
I-V(ZN)HH 2G62,5 (in-house breakout
cable)
A/DQ(ZN)B2Y 4G62,5 (outdoor cable,
with protection against rodents)

Only use Single-mode connection cables for fiber connections that are
based on 3G SFPs.
182
2013-08-14
Specifications
Maximum Acceptable Cable Length
Type of cable
1.25 Gbps
3.125 Gbps
Single-mode 9μm
10,000 m (32,800 ft)
5,000 m (16,400 ft)
Multi-mode 50μm (OM3)
1,000 m (3,280 ft)
500 m (1,640 ft)
Multi-mode 50μm
400 m (1,300 ft)
200 m (650 ft)
Multi-mode 62.5μm
200 m (650 ft)
100 m (325 ft)
If you use single-mode SFPs with multi-mode fibers, you normally can
increase the maximum acceptable cable length.
Type of Connector
Connector
LC Connector
Pos: 131 /806-IHSE/Technische Daten/Verbindungskabel/Koaxial @ 7\mod_1309942381352_6.doc @ 53747 @ 3 @ 1
7.2.3
Coaxial
A point-to-point connection is necessary.
Type of Interconnect Cable
Cable Type
Specifications
Mini coaxial cable AWG 18
RG 6
impedance 75 Ω
Maximum Acceptable Cable Length
Band Width
Maximum Acceptable Cable Length
0.270 Gbit/s
400 m (1,312 ft)
1.485 Gbit/s
140 m (459 ft)
2.970 Gbit/s
120 m (394 ft)
Type of Connector
Connector
Mini BNC connector
Pos: 132 /806-IHSE/Technische Daten/Unterstützte Peripherie/UEB_Unterstützte Peripherie @ 5\mod_1278578478761_6.doc @ 42242 @ 2 @ 1
2013-08-14
183
Draco tera
7.3
Supported Peripherals
Pos: 133 /806-IHSE/Technische Daten/Unterstützte Peripherie/480-xxC/480-xx_KVM-Extender Cat X @ 8\mod_1345795904852_6.doc @ 68081 @ 3 @ 4
The following KVM extenders are released for the use with the Draco tera:
The use of KVM extenders with upgrade modules or USB 2.0 modules
does not limit the operation with the Draco tera.
7.3.1
KVM Extenders with Cat X Connection
K477 Series
Type
Description
L477-1SHC
Draco tera KVM CPU Unit, Single-Head, 2x USB-HID
R477-1SHC
Draco tera KVM CON Unit, Single-Head, 2x USB-HID
L477-1SECA
Draco tera KVM CPU Unit, Single-Head, Analog
Audio, 2x USB-HID and 2x USB 2.0
R477-1SECA
Draco tera KVM CON Unit, Single-Head, Analog
Audio, 2x USB-HID and 2x USB 2.0
L477-1SECD
Draco tera KVM CPU Unit, Single-Head, Digital
Audio, 2x USB-HID and 2x USB 2.0
R477-1SECD
Draco tera KVM CON Unit, Single-Head, Digital
Audio, 2x USB-HID and 2x USB 2.0
L477-1STC
Draco tera KVM CPU Unit, Single-Head, 2x USB-HID,
4x USB 2.0
R477-1STC
Draco tera KVM CON Unit, Single-Head, 2x USB-HID,
4x USB 2.0
L477-2S4C
Draco tera KVM CPU Unit, Dual-Head, 4x USB-HID
R477-2S4C
Draco tera KVM CON Unit, Dual-Head, 4x USB-HID
L477-SHCV
Draco tera KVM CPU Unit, Single-Head,
DVI-I input (VGA), 2x USB-HID
R477-SHCV
Draco tera KVM CON Unit, Single-Head,
DVI-I Input (VGA), 2x USB-HID
K474 Series
Type
Description
L474-BSHC
Draco tera KVM CPU Unit, Single-Head, 2x USB-HID
R474-BSHC
Draco tera KVM CON Unit, Single-Head, 2x USB-HID
L474-BSHCV
Draco tera KVM CPU Unit, Single-Head, DVI-I input
(VGA), 2x USB-HID
R474-BSHCV
Draco tera KVM CON Unit, Single-Head, IR receiver,
2x USB-HID
Pos: 134 /806-IHSE/Technische Daten/Unterstützte Peripherie/480-xx/KVM-Extender Glasfaser @ 7\mod_1311332022151_6.doc @ 54403 @ 3 @ 1
184
2013-08-14
Specifications
7.3.2
KVM Extenders with Fiber Connection (SingleMode)
K477 Series
Type
Description
L477-1SHS
Draco tera KVM CPU Unit, Single-Head, 2x USB-HID
R477-1SHS
Draco tera KVM CON Unit, Single-Head, 2x USB-HID
L477-1SHX
Draco tera KVM CPU Unit, Single-Head, 2x USB-HID,
XV
R477-1SHX
Draco tera KVM CON Unit, Single-Head, 2x USB-HID,
XV
L477-1SESA
Draco tera KVM CPU Unit, Single-Head, Analog
Audio, 2x USB-HID and 2x USB 2.0
R477-1SESA
Draco tera KVM CON Unit, Single-Head, AnalogAudio, 2x USB-HID and 2x USB 2.0
L477-1SEXA
Draco tera KVM CPU Unit, Single-Head, Analog
Audio, 2x USB-HID and 2x USB 2.0, XV
R477-1SEXA
Draco tera KVM CON Unit, Single-Head, Analog
Audio, 2x USB-HID and 2x USB 2.0, XV
L477-1SESD
Draco tera KVM CPU Unit, Single-Head, Digital
Audio, 2x USB-HID and 2x USB 2.0
R477-1SESD
Draco tera KVM CON Unit, Single-Head, Digital
Audio2x USB-HID and 2x USB 2.0
L477-1SEXD
Draco tera KVM CPU Unit, Single-Head, Digital
Audio, 2x USB-HID and 2x USB 2.0, XV
R477-1SEXD
Draco tera KVM CON Unit, Single-Head, Digital
Audio, 2x USB-HID and 2x USB 2.0, XV
L477-1STS
Draco tera KVM CPU Unit, Single-Head, 2x USB-HID,
4x USB 2.0
R477-1STS
Draco tera KVM CON Unit, Single-Head, 2x USB-HID,
4x USB 2.0
L477-1STX
Draco tera KVM CPU Unit, Single-Head, 2x USB-HID,
4x USB 2.0, XV
R477-1STX
Draco tera KVM CON Unit, Single-Head, 2x USB-HID,
4x USB 2.0, XV
L477-2S4S
Draco tera KVM CPU Unit, Dual-Head, 4x USB-HID
R477-2S4S
Draco tera KVM CON Unit, Dual-Head, 4x USB-HID
2013-08-14
185
Draco tera
Type
Description
L477-2S4X
Draco tera KVM CPU Unit, Dual-Head, 4x USB-HID,
XV
R477-2S4X
Draco tera KVM CON Unit, Dual-Head, 4x USB-HID,
XV
L477-1SHSV
Draco tera KVM CPU Unit, Single-Head, DVI-I input
(VGA), 2x USB-HID
R477-1SHSV
Draco tera KVM CON Unit, IR receiver, 2x USB-HID
L477-1SHXV
Draco tera KVM CPU Unit, Single-Head, DVI-I Input
(VGA), 2x USB-HID, XV
R477-1SHXV
Draco tera KVM CON Unit, Single-HEad, DVI-I Input
(VGA), 2x USB-HID, XV
K474 Series
Type
Description
L474-BSHS
Draco tera KVM CPU Unit, Single-Head, 2x USB-HID
R474-BSHS
Draco tera KVM CON Unit, Single-Head, 2x USB-HID
L474-BSHX
Draco tera KVM CPU Unit, Single-Head, 2x USB-HID,
XV
R474-BSHX
Draco tera KVM CON Unit, Single-Head, 2x USB-HID,
XV
L474-BSHSV
Draco tera KVM CPU Unit, Single-Head, DVI-I Input
(VGA), 2x USB-HID
R474-BSHSV
Draco tera KVM CON Unit, Single-Head, IR receiver,
2x USB-HID
L474-BSHXV
Draco tera KVM CPU Unit, Single-Head, DVI-I Input
(VGA), 2x USB-HID, XV
R474-BSHXV
Draco tera KVM CON Unit, Single-Head, DVI-I Input
(VGA), 2x USB-HID, XV
Pos: 135 /806-IHSE/Technische Daten/Unterstützte Peripherie/480-xxC/480-xx_USB-2.0-Extender Cat X @ 8\mod_1345796161347_6.doc @ 68101 @ 3 @ 4
7.3.3
USB 2.0 Extenders with Cat X Connection
K474 Series
Type
Description
L474-BXTC
Draco tera USB 2.0 CPU Unit, 4x USB 2.0
R474-BXTC
Draco tera USB 2.0 CON Unit, 4x USB 2.0
Pos: 136 /806-IHSE/Technische Daten/Unterstützte Peripherie/480-xx/USB-2.0-Extender Glasfaser @ 7\mod_1311332022526_6.doc @ 54422 @ 3 @ 1
186
2013-08-14
Specifications
7.3.4
USB 2.0 Extenders with Fiber Connection (SingleMode)
K474 Series
Type
Description
L474-BXTS
Draco tera USB 2.0 CPU Unit, 4x USB 2.0
R474-BXTS
Draco tera USB 2.0 CON Unit, 4x USB 2.0
L474-BXTX
Draco tera USB 2.0 CPU Unit, 4x USB 2.0, XV
R474-BXTX
Draco tera USB 2.0 CON Unit, 4x USB 2.0, XV
Pos: 137 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
Pos: 138 /806-IHSE/Technische Daten/Pinbelegungen/UEB_Pinbelegungen @ 5\mod_1278578683636_6.doc @ 42315 @ 2 @ 1
2013-08-14
187
Draco tera
7.4
Connector Pinouts
Pos: 139 /806-IHSE/Technische Daten/Pinbelegungen/UEB_CPU-Karte @ 7\mod_1309942897790_6.doc @ 53820 @ 3 @ 1
7.4.1
CPU Board
Pos: 140 /806-IHSE/Technische Daten/Pinbelegungen/Buchse DVI-D Single-Link @ 5\mod_1278578723073_6.doc @ 42333 @ @ 1
Connector DVI-D Single-Link
1.............................8 C1 C2
C5
17...........................24 C3 C4
Pin
Signal
1
T.M.D.S data 2 – 9
Pin
T.M.D.S data 1 – 17
T.M.D.S data 0 –
2
T.M.D.S data 2 + 10
T.M.D.S data 1 + 18
T.M.D.S data 0 +
3
T.M.D.S data 2
GND
11
T.M.D.S data 1
GND
19
T.M.D.S data 0
GND
4
n.c.
12
n.c.
20
n.c.
5
n.c.
13
n.c.
21
n.c.
6
DDC Input (SCL) 14
+5VDC high
impedance
22
T.M.D.S clock
GND
7
DDC Output
(SDA)
15
GND
23
T.M.D.S clock +
8
Internal use
16
Hot Plug
recognition
24
T.M.D.S clock –
C1
Internal use
C3
Internal use
C2
n.c.
C4
Internal use
C5
Signal
GND
Pin Signal
Pos: 141 /806-IHSE/Technische Daten/Pinbelegungen/Buchse USB Typ A @ 5\mod_1278578771214_6.doc @ 42369 @ @ 1
Connector USB Type A
Picture
1 2 3 4
Pin
Signal
Color
1
VCC (+5VDC)
Red
2
Data –
White
3
Data +
Green
4
GND
Black
Pos: 142 /806-IHSE/Technische Daten/Pinbelegungen/D-Sub 9 (Seriell) @ 5\mod_1291128631437_6.doc @ 44882 @ @ 1
188
2013-08-14
Specifications
D-Sub 9 (Serial) RS232
Picture
1.................5
6...........9
Pin
Signal
Pin
Signal
1
n.c.
6
DSR
2
RxD
7
RTS
3
TxD
8
CTS
4
DTR
9
n.c.
5
GND
Pin
Signal
Pin
Signal
1
D1+
5
n.c
2
D1–
6
D2–
3
D2+
7
n.c
4
n.c
8
n.c
Pin
Signal
Pin
Signal
1
D1+
5
D3–
2
D1–
6
D2–
3
D2+
7
D4+
4
D3+
8
D4–
Pos: 143 /806-IHSE/Technische Daten/Pinbelegungen/480-xx/RJ45 @ 7\mod_1309943226649_6.doc @ 53857 @ @ 1
RJ45
Picture
8..........1
Pos: 144 /806-IHSE/Technische Daten/Pinbelegungen/UEB_E/A-Port Cat X @ 7\mod_1309943361243_6.doc @ 53876 @ 3 @ 1
7.4.2
I/O Port Cat X
Pos: 145 /806-IHSE/Technische Daten/Pinbelegungen/RJ45 @ 5\mod_1278578820011_6.doc @ 42405 @ @ 1
RJ45
Picture
8..........1
Pos: 146 /806-IHSE/Technische Daten/Pinbelegungen/UEB_E/A-Port SFP @ 7\mod_1309943436008_6.doc @ 53894 @ 3 @ 1
7.4.3
I/O Port SFP
Pos: 147 /806-IHSE/Technische Daten/Pinbelegungen/Glasfaser SFP Typ LC @ 5\mod_1278938501151_6.doc @ 43210 @ @ 1
Fiber SFP Typ LC
Picture
1
Diode
Signal
1
Data OUT
2
Data IN
2
Pos: 148 /806-IHSE/Technische Daten/Pinbelegungen/UEB_E/A-Port SDI @ 7\mod_1309943510165_6.doc @ 53912 @ 3 @ 1
2013-08-14
189
Draco tera
7.4.4
I/O Port SDI
Pos: 149 /806-IHSE/Technische Daten/Pinbelegungen/Mini-BNC (SDI) @ 7\mod_1309943545633_6.doc @ 53930 @ @ 1
Mini BNC (SDI)
Picture
1 2
Pin
Signal
1
Data IN
2
GND
Pos: 150 /806-IHSE/Technische Daten/Stromversorgung/480-xx @ 7\mod_1309943583946_6.doc @ 53948 @ 2 @ 1
7.5
Power Supply
Nominal Current/Nominal Voltage
Draco tera 288
12 A, 100-240 Vac, 50/60 Hz
Draco tera 160
9 A, 100-240 Vac, 50/60 Hz
Draco tera 80, 48
5 A, 100-240 Vac, 50/60 Hz
Power Requirement
Draco tera 288
max. 202 W without I/O boards
Draco tera 160
max. 188 W without I/O boards
Draco tera 80
max. 99 W without I/O boards
Draco tera 48
max. 94 W without I/O boards
I/O Board
max. 13 W
Pos: 151 /806-IHSE/Technische Daten/Einsatzbedingungen/ATB_Einsatzbedingungen @ 5\mod_1278578980026_6.doc @ 42480 @ 2 @ 1
7.6
Environmental Conditions
Operating Temperature
41 to 113°F (5 to 45°C)
Storage Temperature
–13 to 140°F (–25 to 60°C)
Relative Humidity
Max. 80% non-condensing
Pos: 152 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
190
2013-08-14
Specifications
Pos: 153 /806-IHSE/Technische Daten/Abmessungen/480-xx @ 7\mod_1309943734415_6.doc @ 53966 @ 2 @ 1
7.7
Size
Draco tera 288
Matrix
483 x 578 x 330 mm (19.0" x 22.8" x 12.0")
Shipping Box
650 x 680 x 760 mm (25.6" x 26.8" x 29.9")
Draco tera 160
Matrix
483 x 400 x 330 mm (19.0" x 15.8" x 12.0")
Shipping Box
650 x 680 x 540 mm (25.6" x 26.8" x 21.3")
Draco tera 80
Matrix
483 x 178 x 230 mm (19.0" x 7.0" x 9.1")
Shipping Box
640 x 570 x 360 mm (25.2" x 22.4" x 14.2")
Draco tera 48
Matrix
483 x 133 x 230 mm (19.0" x 5.3" x 9.1")
Shipping Box
640 x 570 x 316 mm (25.2" x 22.4" x 12.4")
Pos: 154 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
191
Draco tera
Pos: 155 /806-IHSE/Technische Daten/Transportgewicht /480-xx @ 7\mod_1309943775602_6.doc @ 53984 @ 2 @ 1
7.8
Shipping Weight
Draco tera 288
Matrix
34.6 kg (76.2 lb) fully equipped
Shipping Box
41.1 kg (90.6 lb)
Draco tera 160
Matrix
26.3 kg (60.0 lb) fully equipped
Shipping Box
31.7 kg (69.9 lb)
Draco tera 80
Matrix
11.1 kg (24.5 lb) fully equipped
Shipping Box
15.6 kg (34.4 lb)
Draco tera 48
Matrix
8.9 kg (19.6 lb) fully equipped
Shipping Box
12.1 kg (26.7 lb)
Pos: 156 /806-IHSE/Technische Daten/MTBF/480_MTBF @ 9\mod_1375173854011_6.doc @ 79261 @ 2 @ 4
192
2013-08-14
Specifications
7.9
MTBF
The following table contains the mean time between failure (MTBF) in
power-on hours (POH). The estimate is based on the FIT rates of the
parts included. FIT rates are based on normalized environmental
conditions of T = 60°C and activation energy (Ea) of 0.7 eV. Calculations
are based on 90% confidence limit.
We estimate that inside the housing, temperature will be 15°C higher than
the ambient temperature. Therefore, the MTBF calculation refers to an
ambient temperature of 45°C. The humidity is limited to 60%.
Draco tera 288 chassis
260,000 POH
Draco tera 160 chassis
310,000 POH
Draco tera 80 chassis
320,000 POH
Draco tera 48 chassis
350,000 POH
CPU board
480,000 POH
I/O board SFP
500,000 POH
I/O board Cat X
410,000 POH
Draco tera 288/160 PSU
200,000 POH
Draco tera 80/48 PSU
130,000 POH
Pos: 157 /806-IHSE/Wartung/480-xx_Wartung @ 8\mod_1351506868807_6.doc @ 69520 @ 122222 @ 4
2013-08-14
193
Draco tera
8
Maintenance
The Draco tera contains various components and assemblies that can be
maintained. All relevant components and assemblies are hot swappable
and can be removed and exchanged during operation.
The following exchangeable components can be found within the Draco
tera:
8.1
Power Supply Units
In order to exchange the power supply units, proceed as follows:
8.2
1.
Make sure that the power cord cable is removed from the power
supply that has to be exchanged.
2.
Unlock the locking screw(s).
3.
With the power supply units of Draco tera 288 and 160, turn the
unlocked bracket down.
4.
Pull the power supply unit out of the corresponding slot.
5.
Push a new or maintained power supply unit into the slot and lock it
accordingly.
6.
Connect the power cord cable to the power supply unit. It will be
recognized by the system and can be used afterwards.
Fan trays
In order to exchange the fan trays, proceed as follows:
194
1.
Unlock the locking screw(s).
2.
Pull the fan tray out of the corresponding slot by using the provided
mount.
3.
Push a new or maintained fan tray into the slot.
4.
Lock the fan tray accordingly. It will be recognized by the system and
can be used afterwards.
2013-08-14
Maintenance
8.3
CPU Board
In order to exchange the CPU board, proceed as follows:
1.
Pull the locking pin slowly out of the CPU board up to the stop.
Wait until the CPU board will be deregistered from the matrix. The deregistration will be confirmed by a permanent green light of the status
LED #1 at the CPU board (see Chapter 3.7.1, Page 19).
2.
Remove all cables from the CPU board.
3.
Pull the CPU board out of the corresponding slot by using the locking
pin.
4.
Push a new or maintained CPU board into the slot and lock it
accordingly.
A successful registration of the CPU board will be shown by a
permanent green flashing of status LED #1.
5.
Connect all cables to the CPU board according to the exchanged
board.
When exchanging a CPU board the new one will automatically receive the
current matrix configuration. During CPU board exchange the Draco tera
should not be switched off.
8.4
I/O-Board
In order to exchange a I/O board, proceed as follows:
1.
Pull the locking pin slowly out of the I/O board up to the stop.
Wait until the I/O board will be deregistered from the matrix. The
deregistration will be confirmed by a permanent green light of the
status LED #1 at the CPU board (see Chapter 3.7.1, Page 19).
2.
Remove all cables from the I/O board.
3.
Pull the I/O board out of the corresponding slot by using the locking
pin.
4.
Push a new or maintained CPU board into the slot and lock it
accordingly.
A successful registration of the CPU board will be shown by a
permantent green flashing of status LED #1.
5.
2013-08-14
Connect all cables to the I/O board according to the exchanged
board.
195
Draco tera
For the use in a 24/7 operation it is recommended to keep all relevant
components of the matrix including a chassis as spare parts available.
8.5
Filter Pads
The pollution of the filter pads has to be checked regularly and the pads
have to be cleaned with slight compressed air or suction by the operator of
the system.
The inspection cycle depends on the ambient air and cannot be
determined generally. A period of 6 months should not be exceeded.
A replacement of the filter pads or the filter trays has to be performed
every year.
In order to replace a filter pad, proceed as follows:
1.
Pull the filter pad together with the mounting frame out of the proper
slot by using the handle.
2.
Press the used filter pad out of the mounting frame.
3.
Insert a new filter pad into the mounting frame.
4.
Put the mounting frame back into the slot again.
Pos: 158 /806-IHSE/Hilfe im Problemfall/UEB_Hilfe im Problemfall @ 5\mod_1278579113839_6.doc @ 42536 @ 1 @ 1
196
2013-08-14
Troubleshooting
9
Troubleshooting
Pos: 159 /806-IHSE/Hilfe im Problemfall/Hilfe im Problemfall (480-xx) @ 7\mod_1309943852774_6.doc @ 54002 @ @ 1
In the following chapters, support for problems with the Draco tera matrix
is provided. This help is based on a working point-to-point extender
connection concerning the contents. Please ensure before running your
extenders with the matrix that they work over a peer-to-peer connection.
This can be supported by the use of a Cat X or fiber coupler. If you have
problems referring to this, the manuals of the respective extenders will
offer support.
Pos: 160 /806-IHSE/Hilfe im Problemfall/Externe Störung/480-xx @ 7\mod_1309944289555_6.doc @ 54021 @ 2 @ 1
9.1
External Failure
Diagnosis
Possible Reason
Matrix cannot be Fuse at the standard
started
appliance outlet.
anymore.
Measure
 Check fuse.
Pos: 161 /806-IHSE/Hilfe im Problemfall/Bildstörung/480-xx @ 7\mod_1309944461727_6.doc @ 54076 @ 2 @ 1
9.2
Video Interference
Diagnosis
Possible Reason
Measure
Opening the
OSD not
possible
No OSD jumper set
 Set jumper 11 on the CON unit.
Incorrect video
display
Cable connection
disturbed
 Check the connection, length
and quality of the interconnect
cable to the units.
Pos: 162 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
197
Draco tera
Pos: 163 /806-IHSE/Hilfe im Problemfall/Lüfterstörung/480-xx @ 7\mod_1309944511868_6.doc @ 54095 @ 2 @ 1
9.3
Malfunction of Fans
Diagnosis
Possible Reason
Measure
Fans only run
under full load
Communication to fan
tray is disturbed
 Removal and und reinstallation
of the fan tray
 Swap both fan trays to the other
slot.
 Restart the matrix.
Fans do not
Fans defective
run, LED OK on
 Contact your dealer
Fans do not
Power supply
run, LED OK off
 Check power supply and power
connection
Pos: 164 /806-IHSE/Hilfe im Problemfall/Störung der Netzteile/480-xx @ 7\mod_1309944565727_6.doc @ 54114 @ 2 @ 1
9.4
Malfunction of Power Supply Units
Diagnosis
Possible Reason
Measure
Matrix cannot
be started
Power supply units not
locked correctly
 Check lock and plug-in of the
power supply units
No power supply
available
 Check, if cables for the power
supply are connected correctly
Power supply units are
not switched on
 Check slide to switch on the
power supply units
Pos: 165 /806-IHSE/Hilfe im Problemfall/Netzwerkstörung/480-xx @ 7\mod_1309944607415_6.doc @ 54133 @ 2 @ 1
9.5
Network Error
Diagnosis
Possible Reason
Measure
Network
settings are not
assumed after
editing.
Restart of the matrix not
yet completed.
 Do a restart.
Pos: 166 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
198
2013-08-14
Troubleshooting
Pos: 167 /806-IHSE/Hilfe im Problemfall/Störung an der Matrix/480-xx @ 7\mod_1309944331383_6.doc @ 54040 @ 2 @ 1
9.6
Failure at the Matrix
Diagnosis
Possible Reason
Measure
Serial control
impossible or
only restrictedly
possible.
Different Baud rate of
CPU and matrix.
 Adapt Baud rate in the matrix
and in the CPU (see Chapter
5.3.2, Page 72).
Serial control via Wrong network cable.
RJ45 port not
possible.
 Use a crossed network cable
Port definitions
as USB 2.0
invalid.
 Do a restart.
Restart of the matrix not
yet completed.
Pos: 168 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
199
Draco tera
Pos: 169 /806-IHSE/Hilfe im Problemfall/Bildausfall/480-xx @ 7\mod_1309944397665_6.doc @ 54058 @ 2 @ 1
9.7
Blank Screen
1 2
3
12
3
Rear View
3
Front View
Diagnosis
Possible Reason
Measure
Monitors
remains dark
after switching
operation
Switching to a CPU Port
without active Source
(computer, CPU).
 Switching to a CPU Port with an
active source (computer, CPU).
LED 1 on or
LED 2 off
Connections CON unit,
matrix and CPU unit.
 Check connecting cables and
connectors. (No cable, cable
break, CPU/CON unit offline,
CPU/CON unit connected to the
wrong port)
LED 3 off
Power supply
 Check power supply units and
the connection to the power
network.
Connection of a console  Check connections regarding
CON and CPU ports at the
with a CON port or
matrix.
connection of a CPU to a
CPU port not established
correctly.
Pos: 170 /806-IHSE/Technische Unterstützung/ATB_Technische Unterstützung @ 5\mod_1278579487089_6.doc @ 42650 @ 122 @ 1
200
2013-08-14
Technical Support
10
Technical Support
Prior to contacting support please ensure you have read this manual, and
then installed and set-up your Draco tera as recommended.
10.1
Support Checklist
To efficiently handle your request it is necessary to complete our checklist
for support and problem cases (Download). Keep the following information
available before you call:
10.2

Company, name, phone number and email

Type and serial number of the device (see bottom of device)

Date and number of sales receipt, name of dealer if necessary

Issue date of the existing manual

Nature, circumstances and duration of the problem

Involved components (such as graphic source/CPU, OS, graphic
card, monitor, USB-HID/USB 2.0 devices, interconnect cable)
including manufacturer and model number

Results from any testing you have done
Shipping Checklist
1.
To return your device, contact your dealer to obtain a RMA number
(Return-Material-Authorization).
2.
Package your devices carefully, preferably using the original box.
Add all pieces which you received originally.
3.
Note your RMA number visibly on your shipment.
Devices that are sent in without a RMA number cannot be accepted. The
shipment will be sent back without being opened, postage unpaid.
Pos: 171 /806-IHSE/Zertifikate/UEB_Zertifikate @ 5\mod_1278579534933_6.doc @ 42668 @ 1 @ 1
2013-08-14
201
Draco tera
11
Certificates
Pos: 172 /806-IHSE/Zertifikate/ATB_Europäische Konformitätserklärung @ 5\mod_1278579640901_6.doc @ 42686 @ 2 @ 1
11.1
CE Declaration Of Conformity
The products listed below in the form as delivered comply with the
provisions of the following European Directives:
2004/108/EG
Council Directive on the approximation of the laws of
the Member States relating to electromagnetic
compatibility
CE Marking 2009
Product list:
K480 Serie
The products comply with the following harmonized standards for
Information Technology Equipment:

EN 55022:2006 + A1:2007 (Class A)

EN 55024:1998 + A1:2001 + A2:2003
This declaration certifies the conformity to the specified directives but
contains no assurance of properties. The safety instructions and
installation guidelines noted in this manual shall be considered in detail.
Compliance with the specifications for cable lengths and types is
mandatory.
Manufacturer:
Oberteuringen, 26 January 2010
IHSE GmbH
Maybachstrasse 11
88094 Oberteuringen
Deutschland
The Management
Use in a Domestic Environment
This is a Class A product. In a domestic environment, this product may
cause radio interference in which case the user may be required to take
adequate measures.
202
2013-08-14
Certificates
11.2
North American Regulatory Compliance
This equipment has been found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Shielded cables must be used with this equipment to maintain compliance
with radio frequency energy emission regulations and ensure a suitably
high level of immunity to electromagnetic disturbances.
All power supplies are certified to the relevant major international safety
standards.
Pos: 173 /806-IHSE/Zertifikate/474-xx_Produktsicherheit @ 9\mod_1373964601786_6.doc @ 77511 @ 2 @ 4
11.3
Product Safety
The product safety of the devices is proven by the compliance to the
following standards:

IEC 60950-1A1:2010

EN 60950-1/A12:2011

UL 60950-1-2007

CAN/CSA-C22.2 60950-1-07
The compliance is verified and confirmed by TÜV Süd, Germany.
Pos: 174 /806-IHSE/Zertifikate/ATB_WEEE @ 5\mod_1278579673292_6.doc @ 42704 @ 2 @ 1
2013-08-14
203
Draco tera
11.4
WEEE
The manufacturer complies with the EU Directive 2012/19/EU on the
prevention of waste electrical and electronic equipment (WEEE).
The device labels carry a respective marking.
Pos: 175 /806-IHSE/Zertifikate/ATB_RoHS @ 5\mod_1278579714214_6.doc @ 42722 @ 2 @ 1
11.5
RoHS/RoHS 2
This device complies with the Directive 2011/65/EU of the European
Parliament and of the council of 8 June 2011 on the restriction of the use
of certain hazardous substances in electrical and electronic equipment
(RoHS 2, RoHS II).
The device labels carry a respective marking.
Pos: 176 /806-IHSE/Glossar/ATB_Glossar @ 5\mod_1278576825433_6.doc @ 41890 @ 1 @ 1
204
2013-08-14
Glossary
12
Glossary
The following terms are commonly used in this guide or in video and KVM
technology:
Term
Explanation
AES/EBU
Digital audio standard that is officially known as
AES3 and that is used for carrying digital audio
signals between devices.
Cat X
Any Cat 5e (Cat 6, Cat 7) cable
CGA
The Color Graphics Adapter (CGA) is an old analog
graphic standard with up to 16 displayable colors and
a maximum resolution of 640x400 pixels.
Component
Video
The Component Video (YPbPr) is a high-quality
video standard that consists of three independently
and separately transmittable video signals, the
luminance signal and two color difference signals.
Composite Video The Composite Video is also called CVBS and it is
part of the PAL TV standard.
CON Unit
Component of a Draco tera or Media Extender to
connect to the console (monitor(s), keyboard and
mouse; optionally also with USB 2.0 devices)
Console
Keyboard, mouse and monitor
CPU Unit
Component of a Draco tera or Media Extender to
connect to a source (computer, CPU)
CVBS
The analog color video baseband signal (CVBS) is
also called Composite Video and it is part of the PAL
TV standard.
DDC
The Display Data Channel (DDC) is a serial
communication interface between monitor and
source (computer, CPU). It allows a data exchange
via monitor cable and an automatic installation and
configuration of a monitor driver by the operating
system.
Dual Access
A system to operate a source (computer, CPU) from
two consoles
Dual Link
A DVI-D interface for resolutions up to 2560x2048 by
signal transmission of up to 330 MPixel/s (24-bit)
Dual-Head
A system with two video connections
2013-08-14
205
Draco tera
206
Term
Explanation
DVI
Digital video standard, introduced by the Digital
Display Working Group (http://www.ddwg.org). Single
Link and Dual Link standard are distinguished. The
signals have TMDS level.
DVI-I
A combined signal (digital and analog) that allows
running a VGA monitor at a DVI-I port – in contrast to
DVI-D (see DVI).
EGA
The Enhanced Graphics Adapter (EGA) is an old
analog graphic standard, introduced by IBM in 1984.
A D-Sub 9 connector is used for connection.
Fiber
Single-mode or multi-mode fiber cables
HDMI
An interface for an all-digital transmission of audio
and video data. It is differentiated between the HDMI
standards 1.0 to 1.4a.
The signals have TMDS level.
KVM
Keyboard, video and mouse
Mini-XLR
Industrial standard for electrical plug connections
(3 pole) for the transmission of digital audio and
control signals
Multi-mode
62.5µ multi-mode fiber cable or 50µ multi-mode fiber
cable
OSD
The On-Screen-Display is used to display information
or to operate a device.
Quad-Head
A system with four video connections
RCA (Cinch)
A not standardized plug connection for transmission
of electrical audio and video signals, especially with
coaxial cables
S/PDIF
A digital audio interconnect that is used in consumer
audio equipment over relatively short distances.
SFP
SFPs (Small Form Factor Pluggable) are pluggable
interface modules for Gigabit connections. SFP
modules are available for Cat X and fiber
interconnect cables.
Single Link
A DVI-D interface for resolutions up to 1920x1200 by
signal transmission of up to 165 MPixel/s (24-bit).
Alternative frequencies are Full HD (1080p), 2K HD
(2048x1080) and 2048x1152.
Single-Head
A system with one video connection
Single-mode
9µ single-mode fiber cable
2013-08-14
Glossary
Term
Explanation
S-Video (Y/C)
The S-Video (Y/C) is a video format transmitting
luminance and chrominance signals separately.
Thereby it has a higher quality standard than CVBS.
TOSLINK
Standardized fiber connection system for digital
transmission of audio signals (F05 plug connection)
Triple-Head
A system with three video connections
USB-HID
USB-HID devices (Human Interface Device) allow for
data input.
There is no need for a special driver during
installation; "New USB-HID device found" is reported.
Typical HID devices include keyboards, mice,
graphics tablets and touch screens. Storage, video
and audio devices are not HID.
VGA
Video Graphics Array (VGA) is a computer graphics
standard with a typical resolution of 640x480 pixels
and up to 262,144 colors. It can be seen as a
follower of the graphics standards MDA, CGA and
EGA.
Pos: 177 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.doc @ 69462 @ @ 1
2013-08-14
207
Draco tera
Pos: 178 /806-IHSE/Glossar/480-xx @ 7\mod_1309944815290_6.doc @ 54151 @ 2 @ 1
12.1
208
Matrix specific Glossary
Term
Explanation
Auto Disconnect
Matrix function that allows an automatic disconnect
between a console and a CPU, if OSD is opened via
this console.
Auto Logout
Matrix function that describes the duration of
inactivity after the user has been logged out from the
OSD at this console.
CON Device
Logical term that summarizes several physical
extenders to switch more complex console systems
via matrix.
CON Timeout
Matrix function that allows an automatic disconnect of
the own console from the connected CPU after a
predefined time.
Console ACL
Console Access Control List is a list that shows the
respective switching rights for the various consoles.
CPU Auto
Connect
Matrix function that allows an automatic connection
establishment between the own console and a
random CPU that is available.
CPU Device
Logical term that summarizes several physical
extenders to switch more complex CPU systems via
matrix.
CPU Timeout
Matrix function that allows the user to disconnect
after a predefined period of time of inactivity from the
respective CPU.
EXT Unit
Part or extender board of a CON or CPU unit with a
connection to the matrix. A CON or CPU unit can
consist of several EXT devices.
Force Connect
Matrix function that allows to switch with the own
console to a CPU that is already used and in doing
so to take keyboard and mouse control. The
connected console so far loses K/M control, but
keeps video.
Force
Disconnect
Matrix function that allows to switch with the own
console to a CPU that is already used and in doing
so to take KVM control. The connected console so
far loses complete KVM control.
Java Tool
Java based control and configuration tool for the
Draco tera matrix.
2013-08-14
Glossary
Term
Explanation
Keyboard
Connect
Matrix function that allows taking over the keyboard
control of an inactive console.
Macro Keys
Programmable keys that can execute a stringing
together of commands to the matrix.
Mouse Connect
Matrix function that allows taking the mouse control
of an inactive console.
Non-BlockingAccess
Matrix configuration where no user can be disturbed
by an activity of another user.
OSD Timeout
Matrix function that closes the OSD automatically
after a predefined period of time of inactivity.
Release Time
Matrix function that allows a console that is
connected with the same CPU to release the K/M
control after a predefined time.
Service Mode
Defined maintenance condition that allows updating
of extenders that are connected to the matrix.
Tie-Line
Communication connection to and between
extension modules in a network environment.
User ACL
User Access Control List is a list that shows the
respective switching rights for the various users.
Video Sharing
Matrix function that allows switching from the own
console to any CPU with video.
=== Ende der Liste für Textmarke Inhalt ===
2013-08-14
209
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising