EWF10831 1 2 3 4 5 1 2 3 4 5 6 7 8 9 Maximum temperature are : 90ºC for Cottons and Cottons Eco 60ºC for Synthetics , Easy Iron and Jeans ; ; 40ºC for Delicates , Delicates Plus , Sport Intensive , Woollens and Hand Wash ; 30ºC for Silk . for Cottons , Cottons Eco Jeans , Spin , Rinse : 1000 rpm; , for Synthetics , Delicates , Delicates Plus , Sport Intensive , Silk , Easy Iron , Woollens , Hand Wash : 700 rpm. (NOT available for Easy Iron and Spin programmes.) Soil Level Icon Type of fabric Intensive For heavy soiled items Normal For normal soiled items Daily For daily soiled items Light For slightly soiled items Quick For very slightly soiled items Super Quick 1) For items used or worn for a short time Refresh 1) For refreshing items only Super Refresh1) For refreshing a very few items only 1) We recommend you to reduce the load sizes (see Washing programmes table). - Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. 1. Using a spanner unscrew and remove the two rear bottom screws. 2. Slide out the two plastic pins. 3. Lay the machine on its back ensuring that the hoses are not crushed. Place one of the polystyrene angle packings under the machine. 3. Some models are provided with a bottom cover that will be found inside the washing machine drum. 2 After ensuring the polyethylene 2 bags have been removed, follow 1 A below instruction: (1). Locate the bottom cover as shown in position (A). (2). Then push the top end to lock to the bottom of washing machine. 4. Remove the polystyrene base, set the machine upright and unscrew the remaining rear screw. Slide out the relevant pin. 5. Cover all the open holes with the plugs which you can find in the bag containing the instruction booklet. Positioning Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or cupboard units. Carefully level by screwing the adjustable feet in or out. The inlet hose must not be lengthened. If it is too short and you do not wish to move the tap, you will have to purchase a new, longer hose specially designed for this type of use. Water drainage The end of the drain hose can be positioned in three ways: Hooked over the edge of a sink using the plastic hose guide supplied with the machine. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. Water inlet Connect the water inlet hose to a tap with 3/4” BSP thread. Use the hose supplied with the washing machine. DO NOT USE OLD HOSES. In this case, make sure the end cannot come unhooked when the machine is emptying. This could be done by tying it to the tap with a piece of string or attaching it to the wall. The other end of the inlet hose which connects to the machine can be turned in any direction. In a sink drain pipe branch. This branch must be above the trap so that the bend is at least 60 cm above the ground. Simply loosen the fitting, rotate the hose and retighten the fitting, making sure there are no water leaks. Directly into a drain pipe at a height of not less than 60 cm and not more than 90 cm. The end of the drain hose must always be ventilated, i.e. the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose. The drain hose must not be kinked. Run it along the floor; only the part near the drainage point must be raised. 60 cm 90 cm For the correct functioning of the machine the drain hose must remain hooked on the proper support piece situated on the top part of back side of the appliance. Electrical Connection This machine is designed to operate on a 220-240 V, single-phase, 50 Hz supply. “An incorrect power supply may void your warranty.” Check that your domestic electrical installation can take the maximum load required (2.0 kW), also taking into account any other appliances in use. Connect the machine to an earthed socket. The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution. Should the appliance power supply cable need to be replaced, this should be carried out by our Service Centre. Important! When the appliance is installed the power supply cable must be easily accessible. If this appliance is supplied from a cord extension set or electrical portable outlet device, the cord extension set or electrical portable device must be positioned so that it is not subject to splashing or ingress of moisture.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project