Condition Monitoring Custom Products

Condition Monitoring Custom Products
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP580(A) Series Transmitter/Monitor
•
•
•
•
•
•
•
•
•
•
Process Variable
Low Cost
Din rail mount
4-20 mA output
Sensor fault detection
Buffered transducer output
Optional filters
Alert, Danger & OK Alarms and Relays
Trip Multiply
Remote Reset
Description:
The CMCP580(A) Series are process variable transmitters/monitors. They are compatible with several types of inputs including DC voltage and current. They provide a 4-20 mA output proportional to
the overall measurement. Each unit provides power for the associated transducer, processes the
vibration signal to determine overall amplitude, and outputs a 4-20 mA dc current that is proportional
to a user specified range such as 0-100% detection. Combining transmitters with an existing PLC or
DCS system results in a high density, low cost vibration monitoring system. When specified with the
alarm feature, the unit functions as a complete single channel monitor that includes alert and danger
alarms, and output relays.
Buffered Output:
A BNC connector mounted on the front of the unit provides access to the buffered transducer output
signal. This includes both the unfiltered vibration signal, and the DC bias voltage. Portable test
equipment or analyzers can be connected to this output without disturbing other system outputs.
Fault Detection:
On board fault detection circuitry continuously monitors the transducer for normal operation. If a fault
occurs, the output current is reduced to 2 mA to indicate the fault to the readout system. A red LED
on the front of the unit is turned on to provide a local indication of the fault.
Alarms:
This monitoring option adds two independent set points, with LED alarm indicators and output relay
contacts (Alert and Danger). Set points are adjustable via potentiometer, from 0 to 110% of full
scale. Each has an adjustable delay of 1 to 10 seconds. Relay contacts can be independently configured by the user for either Normally Open (NO) (Standard) or Normally Closed (NC) operation.
Relays are normally de-energized and can be configured for latching or non-latching (standard) operation. Latched alarms may be reset locally or by remote contact closure. SPST Relay contacts are
rated 5 Amps @ 30 Vdc or 250 Vac for resistive loads. The Alarm option also provides set point multiplication of 3X via contact closure (2X available).
Displays And Assemblies:
Various display options, NEMA and explosion-proof enclosures, and assembled multi-channel systems are available. Consult your sales representative.
www.cmcpweb.com
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP580(A) Series Transmitter/Monitor
www.cmcpweb.com
Electrical Specifications:
Power: +24 Vdc @ 45 mA max. (30 mA typical at 2 full scale output). Reverse polarity and transient
protection included. (With the Alarm/Relay option installed: 75 mA max.)
Buffered Output: BNC Connector
Accuracy: 0.5 % of Full Scale Range.
Output: 4-20 mA proportional to the full scale range.
Maximum Load: 600 Ohms Resistive.
Case: Isolated.
Environmental Specifications:
Operating Temp.: -20oC to +80oC (-4oF to +176oF).
Storage Temp.: -55oC to +125oC (-67oF to +257oF).
Relative Humidity: 0 - 95% Non-Condensing.
Mounting:
32 mm (G style) or 35 mm (T style) DIN Rail.
Ordering Example: To order a standard solid state temperature monitor that accepts input from a
0-10 VDC input with a Full Scale of 0-100% detection,
specify Part Number: CMCP580A-02-01.
NOTES:
1. The Full Scale option specified at order entry is used by the factory for initial calibration.
However, several other ranges can be jumper selected in the field.
2. Transducer and Full Scale options not listed in the above table are available. Contact
your sales representative.
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP580(A) Series Transmitter/Monitor
www.cmcpweb.com
Ordering Information:
CMCP580(X)-(aa)-(bb)
CMCP580 Process Variable Transmitter
CMCP580A Process Variable Monitor
(aa) Input
01, 1-5 Vdc
02, 0-10 Vdc
03, 4-20 mA
04, 0-20 mA
(bb) Full Scale
01, 0-100%
Specify, Specify Desired Units and Range
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement