User Guide

User Guide
User Guide
Professional Entertainment Technology
TABLE OF CONTENTS
1.
Safety Instruction
2.
Technical Specification
2.1 Inserting/Exchanging rotating gobos
2.2 Beam Angle
3.
Lamp
4.
How To Set The Unit
4.1 Control Panel
4.2 Main Function
5.
How To Control The Unit
5.1 Master/Slave Built-In Preprogrammed Function
5.2 Easy Controller
5.3 ISolution Operation / Universal DMX Controller
5.4 Universal DMX Controller
5.5 DMX512 Configuration
5.6 DMX512 Connection
6.
Troubleshooting
7.
Maintenance and Cleaning
1
1
1. Safety Instruction
Please read carefully the instruction, which includes important
information about installation, operation and maintenance.
WARNING
♦
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this user guide.
♦
Unpack and check carefully there is no transportation damage before using the unit.
♦
Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
♦
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
♦
The unit is for indoor use only. Use only in a dry location.
♦
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
♦
Disconnect main power before fuse/lamp replacement or servicing.
♦
Replace fuse/lamp only with the same type. Do not use any other type of lamp.
♦
Make sure there is no flammable materials close to the unit while operating as it is fire hazard.
♦
Use safety cable when fixes this unit. Don’t handle the unit by taking its head only, but always by
taking its base.
♦
Maximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is higher than
this.
♦
Unit surface temperature may reach up to 85C. Don’t touch the housing bare-hand during its
operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing
bulb or serving as the unit could be very hot.
♦
In the event of serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
♦
Don’t connect the device to any dimmer pack or power pack.
♦
Do not touch any wire during operation as high voltage might be causing electric shock.
Warning
♦
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
♦
Never touch bulb with bare fingers as it is very hot after using.
♦
Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.
♦
Do not start on the unit without bulb enclosure or housing are damaged.
♦
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
♦
Do not look directly at the light while the bulb is on.
2
2
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs
yourself. In the unlikely event your unit may require service, please contact your nearest dealer.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed
to avoid vibration and slipping while operating. Always ensure that the structure to which you are
attaching the unit is secure and is able to support a weight of 20 kgs for each unit.
2.Technical Specification
• Voltage:AC 120V~60Hz or 230V/240V/250V~50/60Hz
• Bulb: HID 150W
• The unit is DMX512 fixture. It features full DMX512 control. It can also be linked together in
master/slave connection, as many as required in and run by built-in program chase sequences
automatically or by sound activation through an internal microphone to create an intelligent effect.
• It can be operated by DMX512 control or can be used as an individual unit without a controller.
• Consistent DMX channel enable iRock, iShow and iMove to be link together.
• Features different preprogrammed chase patterns.
• Please use a 3 pin XLR cable/plug when connecting units together.
• Accurate focusable optics system and ultra smooth stepping motors. Fan cooling.
• Pan : 180 deg. Tilt : 70 deg. (IR-5S-HID/IR-5B-HID/ IS-6S-HID/IS-6B-HID)
• IR-5S-HID/IR-5B-HID Independent gobo wheel with 14 gobos plus open and blackout, including 11
metal, 2 glass and 1 effect gobos with shaking effect, Independent color wheel with 11 dichroic colors
with rainbow effect, and independent shutter
• IR-4C-HID Independent gobo wheel with 14 gobos plus open and blackout, including 8 metal, 1
effect, 1 frost, 2 glass, gobos, and 2 color temperature filters (5600k & 3200k), with shaking effect,
Independent color wheel with 11 dichroic colors with rainbow effect, and independent shutter & dimmer.
• IS-6S/6B/4-HID Professional multi-gobo rotator 14 gobos plus open and blackout, including 11 metal,
2 glass and 1 effect gobos, with shaking and shutter effect, Independent color wheel with 11 dichroic
colors with rainbow effect.
3
3
2.2 Beam Angle
3. Lamp
In case of replacement of the lamp or maintenance, do not open the
fixture within 15 minutes until the unit cools down after switching off.
HID 150W
1. Always switch off the main supply and never handle the lamp or
luminaries when is hot.
2. Do not touch the bulb with bare hands. If this happens, clean the
lamp with denatured alcohol and wipe it with a lint free cloth
before installation.
3. The lamp generates UV radiation. Never operate the
lamp without appropriate shielding.
4. When burning, the lamp operates at high pressure and
there is a slight risk of arc tube rupture. The risk
increases with age, temperature and improper handling
of the lamp. Do not use the lamp any longer than its
specified life.
4
4
HID 150 Lamp installation or replacement
• Always switch power off before installing or replacing the lamp. Never try to replace the lamp when it is
hot.
• Do not touch the bulb with bare hands. Cleaning the lamp with denatured alcohol and wipe with a lint
free cloth when lamp is dirty.
1. Loose the screw on the housing cover.
2. Loose the screws of the lamp wire from terminator
3.
Remove the old lamp from the fixture.
4. Please be care to install the lamp into case, make sure it wedge tightly that it can not move
easily. WARNING: impropriety install will cause the lamp lifespan shorten and maybe
explosion during operation.
5. Connect the lamp wire to the terminator as before.
6.
Please reinstall step 2 and step 1.
5
5
4. How To Set The Unit
4.1 Control Panel
Display
To show the various menu and the selected functions.
LED:
DMX
On
DMX input present
MASTER
On
Master Mode
SLAVE
On
Slave Mode
SOUND
Flashing
Sound activation
Button:
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
To confirm the selected functions
Remote controller input
By connect to the 1/4” microphone jack to control the unit for Stand by, Function and Mode.
Sensitivity
To adjust the sound sensitivity.
Microphone
To receives audio signal for sound activation.
DMX input/output
For DMX512 link, use 3-pin XLR plug cable to link the unit together.
6
6
4.2 Main Function
To select any of the given functions, press the MENU button up to when the required one is showing on
the display. Select the function by ENTER button and the display will blink. Use DOWN and UP button to
change the mode. Once the required mode has been selected, press the ENTER button to setup or it will
automatically return to the main functions without any change after idling 8 seconds. To go back to the
functions without any change press the MENU button. The main functions are showing below:
DMX512 Address Setting
Slave mode " Normal "
Slave mode " 2 Light Show "
Slave mode " 3 Light Show "
Slave mode " 4 Light Show "
Blackout Mode " Yes Blackout "
Blackout Mode " No Blackout "
Normal Color
Split Color
Pan Normal
Pan Inversion
Tilt / Barrel Normal
Tilt / Barrel Inversion
Dimmer Normal
Dimmer Inversion
MENU
LED on
LED off
Display Normal
Display Inversion
Focus Adjust
Self-Test
Fixture Hours
Reset
and
only for color-change
DMX512 Address Setting
Press the MENU button up to when the
is showing on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to change the DMX512 address. Once the address has
been selected, press the ENTER button to setup or automatically return to the main functions without any
change after 8 seconds. To go back to the functions without any change press the MENU button again.
7
7
Slave Mode
Press the MENU button up to when the
is showing on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to select the
mode or
(3 light show) mode or
(normal) or
(2 light show)
(4 light show). Once the mode has been selected, press
the ENTER button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
Blackout Mode
Press the MENU button up to when the
is showing on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to select the
(yes blackout) or
(no
blackout) mode. Once the mode has been selected, press the ENTER button to setup or automatically
return to the main functions without any change after 8 seconds. To go back to the functions without any
change press the MENU button again.
Color Mode
Press the MENU button up to when the
is showing on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to select the
(normal) or
(split color)
mode. Once the mode has been selected, press the ENTER button to setup or automatically return to the
main functions without any change after 8 seconds. To go back to the functions without any change press
the MENU button again.
Pan Inversion
Press the MENU button up to when the
is showing on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to select the
(normal) or
(pan
inversion) mode. Once the mode has been selected, press the ENTER button to setup or automatically
return to the main functions without any change after 8 seconds. To go back to the functions without any
change press the MENU button again.
Tilt Inversion
Press the MENU button up to when the
Barrel Rotation Inversion
(
) is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(normal) or
(tilt/barrel rotation inversion) mode. Once the mode has been selected, press the ENTER button to setup
or automatically return to the main functions
without any change after 8 seconds. To go back to the functions without any change press the MENU
button again.
8
8
Dimmer Inversion
Press the MENU button up to when the
is shown on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to select the
(normal) or
(dimmer
inversion) mode. Once the mode has been selected, press the ENTER button to setup or automatically
return to the main functions without any change after 8 seconds. To go back to the functions without any
change press the MENU button again.
Led Display
Press the MENU button up to when the
is showing on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to select the
(Led on) or
(Led off)
mode. Once the mode has been selected, press the ENTER button to setup or automatically return to the
main functions without any change after 8 seconds. To go back to the functions without any change press
the MENU button again.
Display Inversion
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to when the
is blinking on the display. Use the ENTER button to change to the mode
(display
inversion), It will automatically store after 8 seconds. Or press the ENTER button again return to the
mode
(display normal). To go back to the functions press the MENU button again.
Display normal mode for the fixture putting on the floor.
Display inversion mode for the fixture fixing under ceiling.
Focus Adjust
Press the MENU button up to when the
is blinking on the display. Pressing ENTER button, the
unit will focus on center position. To go back to the functions press the MENU button again.
Self-Test
Press the MENU button up to when the
is blinking on the display. Pressing ENTER button and
the unit will run self-test by built in program. To go back to the functions press the MENU button again.
9
9
Fixture Hours
Press the MENU button up to when the
is blinking on the display. Pressing ENTER button and
the display will show the number of working hours of the unit. To go back to the functions press the
MENU button again.
Reset
Press the MENU button up to when the
is blinking on the display. Pressing ENTER button and
all channels of the unit will return to their standard position. To go back to the functions press the MENU
button again.
5. How To Control The Unit
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
2. By easy controller
3. By IL-0824 ( please refer to the user guide of iLead controller ) or universal DMX controller
No need to turn the unit off when you change the DMX address, as new DMX address setting will be
effected at once. Every time you turn the unit on, it will show its item number on the display and move all
the motors to their ‘home’ position and you may hear some noises for about 20 seconds. After that the
unit will be ready to receive DMX signal or run the built in programs.
5.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other units to give an
automatic, sound activated, synchronized light show. This function is good when you want an instant
show. Its DMX input jack will have nothing plugged into it, and Its master LED will be constantly on and
sound LED will flash to the music. The other units will have to set in slave mode
and select
(normal) or
(2 light show) mode
(3 light show) mode or
(4 light show),
Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave led lights will constantly
on.
and
only for color-change.
2-light show
In
(slave mode),
means the unit works normally and
means 2-light show. In
order to create a great light show, you can set
on the second unit to get
contrast movement to each other, even if you have two units only.
10
10
5.2 Easy Controller
The easy remote control is used only in master/slave mode. By connecting to the
1/4” microphone jack of the first unit, you will find that the remote control on the first
unit will control all the other units as below.
Built-in lighting shows triggered by Easy Controller:
IR-5S-HID
IR-5B-HID
Stand by
Blackout the unit
Function
Strobe
1.Gobo/Color sync. strobe
2.Sync. strobe
3.Two-light strobe
X/Y moving pattern selection
( 12 patterns )
Color/Gobo selection
1. Hold on for gobo change.
2. Press shortly for color
change.
X/Y moving setting
1.Pan position
2.Tilt position
3.Dimmer
Mode
Sound 1
(LED off )
Sound 2
(LED normal blinking)
Slow/Sound 3
(LED on)
Position/ Latch
(LED fast blinking )
Stand by
Blackout the unit
Function
Strobe
1.Gobo/Color sync. strobe
2.Sync. strobe
3.Two-light strobe
Chase pattern selection
( 6 patterns )
Color/Gobo selection
1. Hold on for gobo change.
2. Press shortly for color
change.
Dimmer setting
Mode
Sound 1
(LED off )
Sound 2
(LED normal blinking)
Slow
(LED on)
Latch
(LED fast blinking )
Stand by
Blackout the unit
Function
Strobe
1.Gobo/Color sync. strobe
2.Sync. strobe
3.Two-light strobe
X/Y moving pattern selection
( 12 patterns )
Color/Gobo selection
1. Hold on for gobo change.
2. Press shortly for color
change.
X/Y moving setting
1.Pan position
2.Tilt position
Mode
Sound 1
(LED off )
Sound 2
(LED normal blinking)
Slow/Sound 3
(LED on)
Position/ Latch
(LED fast blinking )
IR-4C-HID
IS-6S-HID
IS-6B-HID
IS-4-HID
Stand by
Blackout the unit
Function
Strobe
1.Gobo/Color sync. strobe
2.Sync. strobe
3.Two-light strobe
Gobo/Color selection
1.Hold on for gobo change.
2.Press shortly for color change.
Mode
Sound
(LED off )
Slow
(LED on)
X/Y moving pattern
5.3.1 iSolution Operation
♦
Consistent DMX configuration enable iRock and iShow to be linked together and controlled at the
same time.
♦
DMX address can be set remotely by iLead controller ( please refer to the user manual of iLead
controller ). No need to calculate the DMX channels of each fixture in the chain.
♦
Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
An universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so
that the units can receive DMX signal.
Press the MENU button up to when the
is showing on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to change the DMX512 address. Once the address has
11
11
been selected, press and keep ENTER button pressed up to when the display stops blinking or storing
automatically 8 seconds later. To go back to the functions without any change press the MENU button
again.
Please refer to the following diagram to address your DMX512 channel for the first 4 units.
DMX address can be set remotely by IL-0824 controller. No need to calculate the DMX channels of each
fixture in the chain.
( Following DMX address setting is based on that all the lighting fixtures are linked together controlled by
the 8-channel iLead IL-0824 controller. )
IR-5S-HID/IR- 5B-HID/IS-6S-HID/IS-6B-HID:
IR-4C-HID/IS-4-HID :
65. 4 DMX512 Configuration
Model
CH1
CH2
IR-5S-HID
Pan
Tilt
CH3
CH4
CH5
Gobo
Color
Gobo
Color
CH6
Shutter
/Shaking
IR-5B-HID
Barrel
Shutter
Rotation
/Shaking
Gobo
Color
Pan
Shutter
IR-4C-HID
No
/Shaking
Dimmer
Function
Shutter
IS-6S-HID
Pan
Tilt
Gobo
Color
Reflector
Gobo
Color
Reflector
/Shaking
IS-6B-HID
Barrel
Shutter
Rotation
/Shaking
Gobo
Color
Pan
Shutter
IS-4-HID
Reflector
/Shaking
12
12
5.5IR-5S/ 5B/4C-HID ( IR-4C-HID is a 4 channel color changer)
13
13
5.5IS-6S/6B/4-HID ( IS-4-HID is a 4 channel gobo rotator )
14
14
5.6 DMX512 Connection
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
1.If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable.
2.At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm 1/4W resistor
between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last
unit.
3.Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to the input of the
next unit. The cable can not branched or split to a `Y` cable. DMX512 is a very high-speed signal.
Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal
and shut down the system.
4.The DMX output and input connectors are pass-through to maintain the DMX circuit, when power is
disconnected to the unit.
5.Each lighting unit needs to have an address set to receive the data sent by the controller. The address
number is between 0-511 (usually 0 & 1 are equal to 1).
6.The end of the DMX512 system should be terminated to reduce signal errors.
7.3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
15
15
6. Troubleshooting
Following are a few common problems that may occur during operation. Here are some
suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connect power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX
polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or
the previous one.
4. Try to use another DMX controller.
5. Check in the DMX cables run near or run alongside to high voltage cables that may cause damage
or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the master/ slave
mode signal.
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
1. Make sure the unit that does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
1. The lamp is not working well. Check the main voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan on the head.
16
16
7. Maintenance and Cleaning
Maintenance:
Filter (for IS series)
Filter (for IR series)
Ballast
Ignitor, capacitor
A. As the pictures shown above, if the cable or cable joints turned yellow or black, please replace the
cable or cable joints immediately.
B. Do maintain the fixtures every two months and make sure that all the screws and terminals have
been locked firmly to make sure the normal performance of the fixtures. Negligence of
maintenance would cause malfunction of the fixture.
Cleaning:
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
y Clean with soft cloth using normal glass cleaning fluid.
y Always dry the parts carefully.
y Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
17
17
EC Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL:2000+A12:2002
Safety of household and similar electrical appliances
Part 1 : General requirements
18
18
Technical Specifications
Power
Fuse
Lamp
AC 120V~60Hz
AC 230/240/250V~50/60Hz
20mm Glass T6.3A
20mm Glass T5A
HID 150W
695 x 340 x 250 mm (IR-5S/5B-HID)
Dimension
360 x 340 x 250 mm (IR-4C-HID)
685 x 380 x 200 mm (IS-6S/6B-HID)
375 380 200
(IS 4 HID)
10.6 kg (IR-5S/5B-HID)
Weight
8 kg (IR-4C-HID)
9.4 kg (IS-6S/6B-HID)
Innovation, Quality, Performance
19
19
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement