Professional Intelligent Scanner IR

Professional Intelligent Scanner IR
Professional Intelligent Scanner
IR-575S
User Guide
Professional Entertainment Technology
EC - Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL: 2000+A12: 2002
Safety of household and similar electrical appliances
Part 1: General requirements
IR-575S
TABLE OF CONTENTS
1. Safety Instruction
2. Technical Specification
2.1 Inserting/Exchanging rotating gobos
2.2 Beam Angle
3. Lamp
4. How To Set The Unit
4.1 Control Panel
4.2 Main Function
4.3 Home Position Adjust
5. How To Control The Unit
5.1 Master/Slave Built-In Preprogrammed Function
5.2 Easy Controller
5.3 iSolution Operation / Universal DMX Controller
5.4 Universal DMX Controller
5.5 DMX512 Configuration
5.6 DMX512 Connection
6. Troubleshooting
7. Fixture Cleaning
1A
IR-575S
IR-575S
1. Safety Instruction
7. Fixture Cleaning
Please read carefully the instruction, which includes important
WARNING
y
y
y
information about installation, operation and maintenance.
The cleaning of internal and external optical lenses and/or mirrors must be carried
out periodically to optimize light output. Cleaning frequency depends on the
environment in which the fixture operates: damp, smoky or particularly dirty
Please keep this User Guide for future consultation. If you sell the unit to another
surrounding can cause greater accumulation of dirt on the unit’s optics.
user, be sure that they also receive this user guide.
y
Clean with soft cloth using normal glass cleaning fluid.
Unpack and check carefully there is no transportation damage before using the
y
Always dry the parts carefully.
unit.
y
Clean the external optics at least every 20 days. Clean the internal optics at
Before operating, ensure that the voltage and frequency of power supply match
least every 30/60 days.
the power requirements of the unit.
y
It’s important to ground the yellow/green conductor to earth in order to avoid
electric shock.
y
The unit is for indoor use only. Use only in a dry location.
y
The unit must be installed in a location with adequate ventilation, at least 50cm
from adjacent surfaces. Be sure that no ventilation slots are blocked.
y
Disconnect mains power before fuse/lamp replacement or servicing.
y
Replace fuse/lamp only with the same type. Do not use any other type of lamp.
y
Make sure there is no flammable materials close to the unit while operating as it
is fire hazard.
y
Use safety cable when fixes this unit. Don’t handle the unit by taking its head only,
but always by taking its base.
y
Maximum ambient temperature is Ta: 40℃. Don’t operate it where the
temperature is higher than this.
y
Unit surface temperature may reach up to 85℃. Don’t touch the housing
bare-hand during its operation. Turn off the power and allow about 15 minutes for
the unit to cool down before replacing bulb or serving as the unit could be very
hot.
y
In the event of serious operating problem, stop using the unit immediately. Never
try to repair the unit by yourself. Repairs carried out by unskilled people can lead
to damage or malfunction. Please contact the nearest authorized technical
assistance center. Always use the same type spare parts.
2A
23A
IR-575S
6. Troubleshooting
Following are a few common problems that may occur during operation. Here
are some suggestions for easy troubleshooting:
IR-575S
y
Don’t connect the device to any dimmer pack or power pack.
y
Do not touch any wire during operation as high voltage might be causing electric
shock.
y
A. The unit does not work, no light and the fan does not work
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to
rain or moisture.
1. Check the connect power and mains fuse.
2. Measure the mains voltage on the mains socket.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if it link
properly.
2. If the DMX LED is on and no response to the channel, check the address
y
Never touch bulb with bare fingers as it is very hot after using.
y
Hot lamp explosion hazard. Do not open the unit within five minutes after
switching off.
y
Do not start on the unit without bulb enclosure or housing are damaged.
y
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
settings and DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or
on PCB of the unit or the previous one.
y
Do not look directly at the light while the bulb is on.
Caution
4. Try to use another DMX controller.
5. Check in the DMX cables run near or run alongside to high voltage cables that
may cause damage or interference to DMX interface circuit.
There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact your nearest dealer.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling.
Installation
2. Check the LED for the response of the master / slave mode signal.
The unit should be mounted via its screw holes on the bracket. Always ensure that
D. No response to the sound
the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure
1. Make sure the unit that does not receive DMX signal.
that the structure to which you are attaching the unit is secure and is able to support
2. Check microphone to see if it is good by tapping the microphone.
10 times weight of the unit.
3. Sensitivity is too low, check and set it higher.
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is
broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
1. The lamp is not working well. Check the mains voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan.
22A
3A
IR-575S
2. Technical Specification
IR-575S
5.5 DMX512 Connection
The DMX512 is widely used in intelligent lighting control, with a maximum of 512
Power supply
- AC 230V/250V~50/60Hz
channels.
Fuse:
- T 10A
Lamp
- MSI 575/ HMI 575 GS/ HMQ 575/2
Optical system
- High efficiency optical system
- High quality optical lens and dichroic colors
- Beam angle : 15°
Shutter/Dimmer
- Blackout, 0~100 smooth dimming and strobe speed variable (1~16 flashes per
second)
Movement
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
- Pan: 180°
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120
- Tilt: 70°
Gobo wheel
ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug
and plug it in the DMX-output of the last unit.
- 5 rotating interchangeable gobos plus open
- Magnetic position for continuous rotating
3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit
- Shaking effect
to the input of the next unit. The cable can not branched or split to a `Y` cable.
Color wheel
DMX512 is a very high-speed signal. Inadequate or damaged cables, soldered
- 6 colors plus white
joints or corroded connectors can easily distort the signal and shut down the
- With rainbow effect
system.
DMX Channels
4. The DMX signal is able to pass through each fixture continuously, so if one fixture
- Standard DMX512 signal addressing and can be controlled by any universal
in the chain is out of order, all the fixtures after this point will not be affected.
DMX controller.
5. Each lighting unit needs to have an address set to receive the data sent by the
- Two channel mode: 8 or 14 channels.
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
6. The end of the DMX512 system should be terminated to reduce signal errors.
8 Channels
Channel 1 = Pan
7. 3 pin XLR connectors are more popular than 5 pin XLR.
Channel 5 = Color
Channel 2 = Tilt
Channel 6 = Gobo Rotating
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
Channel 3 = Shutter/ Shaking
Channel 7 = Dimmer
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+), Pin4/5:
Channel 4 = Gobo
Channel 8 = Focus
Not used.
4A
21A
IR-575S
14 Channels:
IR-575S
14 Channels:
Channel 1 = Pan
Channel 8 = Function
Channel 2 = Pan Fine
Channel 9 = Dimmer
Channel 3 = Tilt
Channel 10 = Shutter/Shaking
Channel 4 = Tilt Fine
Channel 11 = Gobo
Channel 5 = Pan/Tilt Speed
Channel 12 = Gobo Rotating
Channel 6 = Movement Macro
Channel 13 = Color
Channel 7 = Movement range
Channel 14 = Focus
2.1 Inserting/Exchanging rotating gobos
DANGER!
Install the gobos with the device switched off only.
Unplug from mains before!
Open the cover by loosening the fastening screw at the sides of the cover. If you wish
to use other gobo patterns besides the standard gobos, or if the gobos are to be
exchanged, remove the fixation ring with an appropriate tool. Remove the gobo and
insert the new gobo. Press the fixation-ring together and insert it in front of the gobo.
CAUTION!
Never unscrew the screws of the rotating gobo as the ball
bearing will otherwise be opened!
20A
5A
IR-575S
IR-575S
2.2 Beam Angle
65. 3 DMX512 Configuration
8 Channels:
3. Lamp
In case of replacement of the lamp or maintenance, do not open the
fixture within 15 minutes until the unit cools down after switching off.
MSI 575/ HMI 575 GS/ HMQ 575/2
Because of its high internal pressure, there might be a risk that the Discharge
lamp would explode during operation. The lamp emits intense UV radiation which
is harmful to the eyes and skin. The high luminance of the arc can cause severe
damage to the retina if looks directly at the lamp.
1. Always switch off the mains supply and never handle the lamp or luminaries
when it’s hot.
2. Do not touch the bulb with bare hands. If this happens, clean the lamp with
denatured alcohol and wipe it with a lint free cloth before installation.
3. The lamp generates UV radiation. Never operate the lamp without appropriate
shielding.
4. When burning, the lamp operates at high pressure and there is a slight risk of arc
tube rupture. The risk increases with age, temperature and improper handling of
the lamp. Do not use the lamp any longer than its specified life.
6A
19A
IR-575S
5.3.1 iSolution Operation
♦
5. Turn screws left and remove the cover as the drawing below.
Consistent DMX configuration enable IRock 575S to be linked with iShow and
iMove together and controlled at the same time.
♦
IR-575S
6. Remove old lamp from lamp socket. Hold the new lamp only by its metallic base.
Never touch the glass bulb. Insert the new lamp in the lamp socket.
DMX address can be set remotely by iLead controller ( please refer to the user
7. Make sure the lamp is located in the center of the reflector for the best spot.
manual of iLead controller ). No need to calculate the DMX channels of each
fixture in the chain.
♦
Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
If you use an universal DMX controller to control the units, you have to set DMX
address from 1 to 512 channel so that the units can receive DMX signal.
Press the MENU button up to when the
is shown on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to change the
DMX512 address. Once the address has been selected, press and keep ENTER
button pressed up to when the display stops blinking or storing automatically 8
seconds later. To go back to the functions without any change press the MENU
button again.
Please refer to the following diagram to address your DMX512 channel for the first 4
units.
8 Channels:
14 Channels:
You have to set the fixture DMX address in 8 channels mode when you use IL-0824
controller. DMX address can be set remotely by IL-0824 controller. No need to
calculate the DMX channels of each fixture in the chain.
Please refer to the following diagram to address your DMX512 channel for the first 4
units.
8 Channels:
18A
7A
IR-575S
4. How To Set The Unit
IR-575S
5.1 Master/Slave Built In Preprogrammed Function
4.1 Control Panel
By linking the units in master/slave connection, the first unit will control the other
units to give an automatic, sound activated, synchronized light show. This function is
good when you want an instant show. Its DMX input jack will have nothing plugged
into it, and Its master LED will be constantly on and sound LED will flash to the music.
The other units will have to select
(slave 1) or
(slave 2) mode,
Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave led
lights will constantly on.
2-light show
Display
In
To show the various menu and the selected functions .
On
DMX input present
MASTER
On
Master Mode
SLAVE
On
Slave Mode
SOUND
Flashing
Sound activation
MENU
To select the programming functions
means the unit works like the master unit and
means 2-light show. In order to create a great light show, you can set
LED
DMX
(slave mode),
on the second unit to get contrast movement to each other, even if you have
two units only.
5.2 Easy Controller
(Sold Separately)
The easy remote control is used only in master/slave mode. By connecting to the
Button
1/4” microphone jack of the first unit, you will find that the remote control on the first
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
unit will control all the other units as below.
Built-in lighting shows triggered by Easy Controller:
To confirm the selected functions
On/Off
Stand by
Blackout the unit
Function
Strobe
1. Sync. strobe
2.Async. strobe
3.Sound strobe
X/Y moving pattern
selection
( 12 patterns )
Color/Gobo selection
1. Hold on for gobo change.
2. Press shortly for color
change.
Mode
Sound 1
(LED off )
Sound 2
(LED normal
blinking)
Slow/Sound 3
(LED on)
Turns On/Off the power
Fuse
To replace the fuse
Power
To connect to the mains supply
Remote controller input
By connect to the 1/4” microphone jack to control the unit for Stand by, Function and
Mode.
8A
17A
IR-575S
IR-575S
the display will blink. Use DOWN and UP button to adjust the R-gobo home position.
Sensitivity
Once the value has been selected, press the ENTER button to setup or automatically
To adjust the sensitivity for sound activation
return to the offset functions without any change press the MENU button again, To go
DMX input/output
back to the main functions without any change after 8 seconds.
For DMX512 link, use 3-pin XLR plug cable to link the unit together
Gobo Adjust
4.2 Main Function
Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP
button up to when the
is shown on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to adjust the gobo home position.
Once the value has been selected, press the ENTER button to setup or automatically
return to the offset functions without any change press the MENU button again, To go
back to the main functions without any change after 8 seconds.
To select any of the given functions, press the MENU button up to when the required
one is showing on the display. Select the function by ENTER button and the display
will blink. Use DOWN and UP button to change the mode. Once the required mode
has been selected, press the ENTER button to setup or it will automatically return to
the main functions without any change after idling 8 seconds. To go back to the
functions without any change press the MENU button. The main functions are
showing below:
Focus Adjust
Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP
button up to when the
is shown on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to adjust the focus home position.
Once the value has been selected, press the ENTER button to setup or automatically
return to the offset functions without any change press the MENU button again, To go
back to the main functions without any change after 8 seconds.
5. How To Control The Unit
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
2. By easy controller
3. By IL-0824 ( only for setting in 8 channel mode, please refer to the user guide
of iLead controller ) or universal DMX controller
No need to turn the unit off when you change the DMX address, as new DMX
address setting will be effected at once. Every time you turn the unit on, it will show
on the display and move all the motors to their ‘home’ position and you may
hear some noises for about 20 seconds. After that the unit will be ready to receive
DMX signal or run the built in programs.
16A
9A
IR-575S
IR-575S
button up to when the
is shown on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to adjust the pan position. Once the
value has been selected, press the ENTER button to setup or automatically return to
the offset functions without any change press the MENU button again, To go back to
the main functions without any change after 8 seconds.
Pan Adjust
Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP
button up to when the
is shown on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to adjust the tilt position. Once the
value has been selected, press the ENTER button to setup or automatically return to
the offset functions without any change press the MENU button again, To go back to
the main functions without any change after 8 seconds.
Dimmer Adjust
Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP
button up to when the
is shown on the display. Pressing ENTER button. Use
DOWN and UP button to adjust dimmer. Once the value has been selected, press
the ENTER button to setup or automatically return to the offset functions without any
change press the MENU button again, To go back to the main functions without any
change after 8 seconds.
Color Adjust
Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP
button up to when the
is shown on the display. Pressing ENTER button and
the display will blink. Use DOWN and UP button to adjust the color home position.
DMX512 Address Setting
Press the MENU button up to when the
Once the value has been selected, press the ENTER button to setup or automatically
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to change the
return to the offset functions without any change press the MENU button again, To go
back to the main functions without any change after 8 seconds.
DMX512 address. Once the address has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8
R-Gobo Adjust
seconds. To go back to the functions without any change press the MENU button
Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP
again.
button up to when the
10A
is shown on the display. Pressing ENTER button and
15A
IR-575S
(Lamp on when power on) or
(Lamp off when power on) mode.
IR-575S
Channel Mode
Once the mode has been selected, press the ENTER button to setup or
automatically return to the main functions without any change after 8 seconds. To go
back to the functions without any change press the MENU button again.
Press the MENU button up to when the
is shown on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(8 Channels) or
(14 Channels) mode. Once the mode has been
selected, press the ENTER button to setup or automatically return to the main
Software Version
functions without any change after 8 seconds. To go back to the functions without
Press the MENU button up to when the
is blinking on the display. Pressing
any change press the MENU button again.
ENTER button and the display will show the software version. To go back to the
functions press the MENU button again.
Slave Mode
Press the MENU button up to when the
Reset
is shown on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
Press the MENU button up to when the
is blinking on the display. Pressing
ENTER button and all channels of the unit will return to their standard position. To go
back to the functions press the MENU button again.
(slave 1) or
(slave 2) mode. Once the mode has been selected,
press the ENTER button to setup or automatically return to the main functions
without any change after 8 seconds. To go back to the functions without any change
press the MENU button again.
4.3 Home Postion Adjust
Press ENTER button for at least 5 seconds into offset mode to adjust the home
position, the functions are shown below:
Sound Mode
Press the MENU button up to when the
is shown on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(sound mode on) or
(sound mode off) mode. Once the mode has
been selected, press the ENTER button to setup or automatically return to the main
functions without any change after 8 seconds. To go back to the functions without
any change press the MENU button again.
Blackout Mode
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(yes blackout) or
(no blackout) mode. Once the mode has been
selected, press the ENTER button to setup or automatically return to the main
functions without any change after 8 seconds. To go back to the functions without
any change press the MENU button again.
Pan Adjust
Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP
14A
11A
IR-575S
Pan Inversion
IR-575S
Focus Adjust
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or
(pan inversion) mode. Once the mode has been
Press the MENU button up to when the
is blinking on the display. Pressing
ENTER button, use UP and DOWN button to adjust focus. To go back to the
functions press the MENU button again.
selected, press the ENTER button to setup or automatically return to the main
functions without any change after 8 seconds. To go back to the functions without
any change press the MENU button again.
Self-Test
Press the MENU button up to when the
is blinking on the display. Pressing
ENTER button and the unit will run self-test by built in program. To go back to the
Tilt Inversion
functions press the MENU button again.
Press the MENU button up to when the
is shown on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or
(tilt inversion) mode. Once the mode has been selected,
Temperature Test
Press the MENU button up to when the
is blinking on the display. Pressing
press the ENTER button to setup or automatically return to the main functions
ENTER button and the will show on the display. To go back to the functions press the
without any change after 8 seconds. To go back to the functions without any change
MENU button again.
press the MENU button again.
Fixture Hours
Led Display
Press the MENU button up to when the
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(Led on) or
is blinking on the display. Pressing
ENTER button and the display will show the number of working hours of the unit. To
go back to the functions press the MENU button again.
(Led off) mode. Once the mode has been selected,
press the ENTER button to setup or automatically return to the main functions
Lamp On/Off
without any change after 8 seconds. To go back to the functions without any change
Press the MENU button up to when the
press the MENU button again.
is blinking on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(Lamp on) or
Display Inversion
It is good for you to install the unit on the floor or under ceiling. Press the MENU
button up to when the
is blinking on the display. Use the ENTER button to
change to the mode
(display inversion), It will automatically store after 8
seconds. Or press the ENTER button again return to the mode
(display
normal). To go back to the functions press the MENU button again.
(Lamp off) mode. Once the mode has been selected,
press the ENTER button to setup or automatically return to the main functions
without any change after 8 seconds. To go back to the functions without any change
press the MENU button again.
Lamp Mode
Display normal mode for the fixture putting on the floor.
Press the MENU button up to when the
Display inversion mode for the fixture fixing under ceiling.
ENTER button and the display will blink. Use DOWN and UP button to select the
12A
is blinking on the display. Pressing
13A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement