Owners Manual - ESD

Owners Manual - ESD
VOLVO XC90
Owners Manual
Web Edition
DEAR VOLVO OWNER
THANK YOU FOR CHOOSING VOLVO
We hope you will enjoy many years of driving pleasure in your Volvo.
The car has been designed for the safety and comfort of you and your
passengers. Volvo is one of the safest cars in the world. Your Volvo
has also been designed to satisfy all current safety and environmental
requirements.
In order to increase your enjoyment of the car, we recommend that
you familiarise yourself with the equipment, instructions and maintenance information contained in this owner's manual.
Table of contents
00 01 02
00 Introduction
01 Safety
Important information .............................. 10
Volvo and the environment ...................... 13
Seatbelts ..................................................
Symbols, airbags......................................
Airbags......................................................
Activating/deactivating the airbag* ..........
Side airbags (SIPS bags)..........................
Inflatable Curtain (IC)................................
WHIPS.......................................................
Roll-over protection - ROPS.....................
When the systems deploy.........................
Child safety...............................................
02 Instruments and controls
18
21
22
24
26
28
29
31
32
33
Overview, left-hand drive car....................
Overview, right-hand drive car..................
Driver's door control panel.......................
Combined instrument panel......................
Indicator and warning symbols.................
Information display...................................
Switches in the centre console.................
Lighting panel...........................................
Left-hand stalk switch...............................
Trip computer*..........................................
Right-hand stalk switch............................
Cruise control*..........................................
Parking brake, electrical socket, etc.........
Power windows.........................................
Windows, rearview and door mirrors........
Power sunroof*.........................................
44
46
48
49
51
54
55
58
60
61
63
65
67
69
71
76
HomeLinkŸ *.............................................. 78
4
* Option/accessory, for more information, see Introduction.
Table of contents
03 04 05
03 Climate control
04 Interior
05 Locks and alarm
General information on climate control..... 84
Electronic Climate Control, ECC............... 88
Fuel-driven parking heater* ...................... 91
Front seats................................................ 96
Front seats - Executive ............................ 99
Interior lighting........................................ 100
Storage spaces in the passenger compartment.................................................. 102
Storage spaces in the passenger compartment - Executive .............................. 107
Rear seat................................................. 108
Loading .................................................. 110
Cargo area.............................................. 111
Remote control key - key with remote control........................................................... 120
Locking and unlocking............................ 122
Child safety locks.................................... 125
Alarm*..................................................... 127
* Option/accessory, for more information, see Introduction.
5
Table of contents
06 07 08
06 Starting and driving
General....................................................
Refuelling................................................
Starting the engine..................................
Manual gearbox......................................
Automatic gearbox..................................
All-wheel drive*.......................................
Brake system..........................................
Stability and traction control system* ....
Parking assistance*.................................
Blind Spot Information System - BLIS*...
Towing and recovery..............................
Start assistance......................................
Driving with a trailer................................
Towing equipment* ................................
Detachable towbar* ...............................
Adjusting headlamp pattern ...................
6
07 Wheels and tyres
132
134
140
142
143
146
147
149
151
153
157
159
160
162
164
168
General....................................................
Tyre pressure .........................................
Warning triangle* and spare wheel * ......
Changing wheels ...................................
Emergency puncture repair* ..................
* Option/accessory, for more information, see Introduction.
08 Car care
174
177
179
182
184
Cleaning.................................................. 190
Touching up paintwork .......................... 194
Rustproofing........................................... 195
Table of contents
09 10 11
09 Maintenance and service
Volvo service...........................................
Self-maintenance....................................
Bonnet and engine compartment...........
Oils and fluids.........................................
Wiper blades...........................................
Battery.....................................................
Replacing bulbs .....................................
Fuses......................................................
10 Infotainment system
198
199
201
203
207
209
211
218
General....................................................
Control panels, audio .............................
Audio system functions .........................
Radio functions ......................................
CD functions ..........................................
Menu structure – audio system .............
Phone functions* ....................................
Menu structure – phone .........................
Bluetooth handsfree* .............................
RSE - Rear Seat Entertainment system Dual Screen* ..........................................
11 Specifications
232
233
236
240
246
248
249
256
259
Type designation.....................................
Dimensions and weights.........................
Engine specifications..............................
Engine oil................................................
Fluids and lubricants...............................
Fuel.........................................................
Catalytic converter..................................
Electrical system ....................................
Type approval ........................................
Symbols in the display............................
272
274
276
277
279
281
283
284
286
287
265
* Option/accessory, for more information, see Introduction.
7
Table of contents
12
12 Alphabetical Index
Alphabetical Index.................................. 290
8
Table of contents
9
Introduction
Important information
Reading the Owner's Manual
Introduction
A good way of getting to know your new car is
to read the owner's manual, ideally before your
first journey. This will give you the opportunity
to familiarise yourself with new functions, to
see how best to handle the car in different situations, and to make the best use of all the
car's features. Please pay attention to the
safety instructions contained in the manual.
The specifications, design features and illustrations in this owner's manual are not binding.
We reserve the right to make modifications
without prior notice.
©
In the event of uncertainty over what is standard or an option/accessory, contact a Volvo
dealer.
Special texts
WARNING
Warning texts advise of a risk of personal
injury.
IMPORTANT
Important texts advise of a risk of material
damage.
All types of option/accessory are marked with
an asterisk*.
In addition to standard equipment, this manual
also describes options (factory fitted equipment) and certain accessories (retrofitted extra
equipment).
The equipment described in the owner's manual is not available in all cars - they have different equipment depending on adaptations
for the needs of different markets and national
or local laws and regulations.
The car contains different types of decal which
are designed to convey important information
in a simple and clear manner. The decals in the
car have the following descending degree of
importance for the warning/information.
Warning for personal injury
NOTE texts give advice or tips that facilitate
the use of features and functions for example.
Footnote
There is footnote information in the owner's
manual that is located at the bottom of the
page. This information is an addition to the text
that it refers to via a number. If the footnote
refers to text in a table then letters are used
instead of numbers for referral.
Message texts
There are displays in the car that show text
messages. These text messages are high-
10
Decals
NOTE
Volvo Car Corporation
Option
lighted in the owner's manual by means of the
text being slightly larger and printed in grey.
Examples of this are in menu texts and message texts on the information display (e.g.
Audio mode).
* Option/accessory, for more information, see Introduction.
G031590
Black ISO symbols on yellow warning field,
white text/image on black message field. Used
to indicate the presence of danger which, if the
Introduction
Important information
warning is ignored, may result in serious personal injury or fatality.
Information
Procedure lists
Procedures where action must be taken in a
certain sequence are numbered in the owner's
manual.
Risk of property damage
When there is a series of illustrations for
step-by-step instructions each step is
numbered in the same way as the corresponding illustration.
G031592
G031593
There are numbered lists with letters adjacent to the series of illustrations where the
order of the instructions is not significant.
White ISO symbols and white text/image on
black or blue warning field and message field.
Used to indicate the presence of danger which,
if the warning is ignored, may result in damage
to property.
White ISO symbols and white text/image on
black message field.
NOTE
The labels shown in the owner's manual are
not provided as exact reproductions of
those in the car. The purpose is to show
their approximate appearance and location
in the car. The information that applies to
your car in particular is available on the label
in question in your car.
Arrows appear numbered and unnumbered and are used to illustrate a movement.
If there is no series of illustrations for step-bystep instructions then the different steps are
numbered with normal numbers.
Position lists
Red circles containing a number are used
in overview images where different components are pointed out. The number
recurs in the position list featured in connection with the illustration that describes
the item.
Bulleted lists
A bulleted list is used when there is a list of
points in the owner's manual.
Example:
11
Introduction
Important information
• Coolant
• Engine oil
To be continued
`` This symbol is located furthest down to the
right when a section continues on the following
page.
Recording data
The driving and safety systems in the car use
computers which check and share information
with each other on the car's function. One or
more of these computers may store information on the systems they check during normal
driving, during the course of a collision or nearcollision. Stored information may be used by:
•
•
•
•
12
Volvo Car Corporation
Service or repair workshops
Police or other authorities
Other parties who claim legal entitlement
for access to the information or someone
who has permission from the owner to
access the information.
Accessories and extra equipment
The incorrect connection and installation of
accessories can negatively affect the car's
electrical system. Certain accessories only
function when their associated software is
installed in the car's computer system. We
therefore recommend that you always contact
an authorised Volvo workshop before installing
accessories which are connected to or affect
the electrical system.
Information on the Internet
At www.volvocars.com there is further information concerning your car.
Introduction
Volvo and the environment
G000000
Volvo Cars' environmental philosophy
Environmental care is one of Volvo Car Corporation's core values which influence all operations. We also believe that our customers share
our consideration for the environment.
Your Volvo complies with strict international
environmental standards and is also manufactured in one of the cleanest and most resourceefficient plants in the world. Volvo Car Corporation has global ISO certification, which
includes the environmental standard ISO
14001 covering all factories and several of our
other units. We also set requirements for our
partners so that they work systematically with
environmental issues.
Fuel consumption
Volvo cars have competitive fuel consumption
in each of their respective classes. Lower fuel
consumption generally results in lower emission of the greenhouse gas, carbon dioxide.
It is possible for the driver to influence fuel consumption. For more information read under the
heading, Reducing environmental impact.
Efficient emission control
Your Volvo is manufactured following the concept "Clean inside and out" – a concept that
encompasses a clean interior environment as
well as highly efficient emission control. In
many cases the exhaust emissions are well
below the applicable standards.
Clean air in the passenger compartment
A passenger compartment filter prevents dust
and pollen from entering the passenger compartment via the air intake.
A sophisticated air quality system, IAQS* (Interior Air Quality System) ensures that the incoming air is cleaner than the air in the traffic outside.
The system consists of an electronic sensor
and a carbon filter. The incoming air is monitored continuously and if there is an increase in
* Option/accessory, for more information, see Introduction.
13
Introduction
Volvo and the environment
the level of certain unhealthy gases such as
carbon monoxide then the air intake is closed.
Such a situation may arise in heavy traffic,
queues and tunnels for example.
The entry of nitrous oxides, ground-level ozone
and hydrocarbons is prevented by the carbon
filter.
Textile standard
The interior of a Volvo is designed to be pleasant and comfortable, even for people with
contact allergies and for asthma sufferers.
Extreme attention has been given to choosing
environmentally-compatible materials. This
means that they also fulfil the requirements in
the Oeko-Tex 100 standard1, a major advance
towards a healthier passenger compartment
environment.
Oeko-Tex certification covers seatbelts, carpets and fabrics for example. The leather in the
upholstery undergoes chromium-free tanning
with plant substances and fulfils the certification requirements.
Volvo workshops and the environment
Regular maintenance creates the conditions
for a long service life and low fuel consumption
for your car. In this way you contribute to a
cleaner environment. When Volvo's workshops
are entrusted with the service and mainte1
14
More information on www.oekotex.com
nance of your car it becomes part of our system. We make clear demands regarding the
way in which our workshops are designed in
order to prevent spills and discharges into the
environment. Our workshop staff have the
knowledge and the tools required to guarantee
good environmental care.
Reducing environmental impact
You can easily help reduce environmental
impact, for example, by driving economically
and by servicing and maintaining the car
according to the instructions in the owner's
manual.
The following additional advice will help you to
do your bit for the environment (for further
advice on how you can reduce environmental
impact and drive economically, see
page 132):
•
Decrease fuel consumption by choosing
ECO tyre pressure, see page 177.
• A roof load and ski box increase air resistance, leading to higher fuel consumption.
Remove them directly after use.
•
Remove unnecessary items from the car.
The greater the load the higher the fuel
consumption.
• If the car is equipped with an engine block
heater, always use it before starting from
cold. This reduces fuel consumption and
exhaust emissions.
• Drive gently and avoid braking too hard.
• Drive in the highest gear possible. Low
engine speeds result in lower fuel consumption.
• Use engine braking to slow down.
• Avoid letting the engine idle. Pay attention
to local regulations. Switch off the engine
when stationary for longer periods.
• Always dispose of environmentally hazardous waste, such as batteries and oils, in
an environmentally safe manner. We recommend that you consult an authorised
Volvo workshop for advice if you are uncertain about the disposal of this type of
waste.
• Service your car regularly.
• High speed increases consumption considerably due to increased wind resistance. A doubling of speed increases wind
resistance 4 times.
These hints will help reduce fuel consumption
without increasing travel time or lessening the
enjoyment of driving. Apart from being kind to
your car, you'll be saving money - and the
Earth's resources.
Introduction
Volvo and the environment
Recycling
As a part of Volvo's environmental work, it is
important that the car is recycled in an environmentally sound manner. Almost all of the
car can be recycled. The last owner of the car
is therefore requested to contact a dealer for
referral to a certified/approved recycling
facility.
The owner's manual and the
environment
The FSC symbol shows that the paper pulp in
this publication comes from FSC certified forests or other controlled sources.
15
Seatbelts ................................................................................................
Symbols, airbags....................................................................................
Airbags....................................................................................................
Activating/deactivating the airbag* ........................................................
Side airbags (SIPS bags)........................................................................
Inflatable Curtain (IC)..............................................................................
WHIPS.....................................................................................................
Roll-over protection - ROPS...................................................................
When the systems deploy.......................................................................
Child safety.............................................................................................
16
* Option/accessory, for more information, see Introduction.
18
21
22
24
26
28
29
31
32
33
SAFETY
01 Safety
Seatbelts
01
Always use a seatbelt
Releasing the seatbelt
Press the red lock button and then let the
seatbelt retract. If the seatbelt does not
retract fully, feed the seatbelt in by hand so
that it does not hang loose.
The seatbelt locks and cannot be
withdrawn
G020104
• if it is pulled out too quickly
• during braking and acceleration
• if the car leans heavily.
• do not use clips or anything else that can
prevent the seatbelt from fitting properly
Tensioning the hip strap. The belt must be positioned low down.
• ensure that the seatbelt is not twisted or
Heavy braking can have serious consequences
if the seatbelts are not used. Ensure that all
passengers use their seatbelts. It is important
that the seatbelt lies against the body so it can
provide maximum protection. Do not lean the
backrest too far back. The seatbelt is designed
to protect in a normal seating position.
• the hip strap must be positioned low down
Putting on a seatbelt:
18
Keep in mind the following
Pull the seatbelt out slowly and secure it by
pressing the buckle into the lock. A loud
"click" indicates that the seatbelt has
locked.
caught on anything
(not over the abdomen)
• tension the hip strap over the lap by pulling
the diagonal shoulder belt as illustrated.
WARNING
The seatbelts and airbags interact. If a seatbelt is not used or is used incorrectly, this
may diminish the protection provided by the
airbag in the event of a collision.
WARNING
Each seatbelt is designed for only one person.
WARNING
Never modify or repair the seatbelts yourself. Volvo recommends that you contact an
authorised Volvo workshop. If a seatbelt has
been subjected to a major load, such as in
conjunction with a collision, the entire seatbelt must be replaced. Some of the protective characteristics of the seatbelt may have
been lost, even if it appears to be undamaged. In addition, replace the seatbelt if the
belt is worn or damaged. The new seatbelt
must be type-approved and intended for
installation in the same position as the
replaced seatbelt.
01 Safety
Seatbelts
Seatbelts and pregnancy
of the vehicle as they drive (which means they
must be able to easily operate the foot pedals
and the steering wheel). Within this context,
they should strive to position the seat with as
large a distance as possible between the abdomen and the steering wheel.
Seatbelt reminder
01
roof console and in the combined instrument
panel.
NOTE
The seatbelt reminder is intended for an
adult sitting in the front seat. If a belt-fitted
child seat is fitted in the front seat, the seatbelt reminder does not switch on.
Certain markets
G020105
An acoustic signal and indicator lamp remind
the driver if not wearing a seatbelt to use one.
At low speed, the audio reminder will sound for
the first 6 seconds.
The lap section should lay flat over the thighs
and as low as possible under the abdomen. –
It must never be allowed to ride upward.
Remove the slack from the seatbelt and ensure
that it fits as close to the body as possible. In
addition, check that there are no twists in the
seatbelt.
As a pregnancy progresses, pregnant drivers
should adjust their seats and steering wheel
such that they can easily maintain full control
Seatbelt tensioner
G027049
The seatbelt should always be worn during
pregnancy. But it is crucial that it be worn in the
correct way. The diagonal section should wrap
over the shoulder then be routed between the
breasts and to the side of the abdomen.
An acoustic signal and indicator lamp remind
the driver and front seat passenger to use a
seatbelt if either of them is not wearing one.
The audio reminder is speed dependent (at low
speeds), and time dependent (when the car is
started). The visual reminder is located in the
All the seatbelts (except the centre rear seatbelt) are equipped with seatbelt tensioners. A
mechanism in the seatbelt tensioner tightens
the seatbelt around the body in the event of a
sufficiently violent collision. The seatbelt then
provides more effective restraint for the occupants.
``
19
01 Safety
01
Seatbelts
WARNING
Never insert the tongue of the passenger's
seatbelt into the buckle on the driver's side.
Always insert the tongue of the seatbelt into
the buckle on the correct side. Do not make
any damages on seatbelts nor insert any
foreign objects into a buckle. The seatbelts
and buckles would then possibly not function as intended in the event of a collision.
There is a risk of serous injury.
20
01 Safety
Symbols, airbags
Warning symbol on the combined
instrument panel
01
As well as the warning symbol, a
message may appear on the display in appropriate cases. If the
warning symbol malfunctions, the
warning triangle illuminates and
the message SRS AIRBAG
SERVICE. URGENT appears in
the display. Volvo recommends
that you contact an authorised
Volvo workshop immediately.
WARNING
The warning symbol in the combined instrument panel illuminates when the remote control key is turned to key position I, II or III. The
symbol goes out after approx. 6 seconds provided the airbag system is fault-free.
If the warning symbol for the airbag system
remains illuminated or illuminates while driving, it means that the airbag system does
not have full functionality. The symbol may
indicate a fault in the seatbelt tensioner system, the SIPS, SRS or IC systems. Volvo
recommends that you contact an authorised Volvo workshop immediately.
21
01 Safety
01
Airbags
Airbag system
NOTE
G020110
G020111
The sensors react differently depending on
the course of the collision and whether the
seatbelts on the driver's side and passenger
side are in use.
SRS system, right-hand drive
SRS system, left-hand drive.
The system consists of airbags and sensors. A
sufficiently violent collision trips the sensors
and the airbag(s) are inflated with hot gas. To
cushion the impact, the airbag deflates when
compressed. When this occurs, smoke
escapes into the car. This is completely normal. The entire process, including inflation and
deflation of the airbag, takes place within
tenths of a second.
22
WARNING
Volvo recommends that you contact an
authorised Volvo workshop for repair.
Defective work in the airbag system could
cause malfunction and result in serious personal injury.
It is therefore possible that only one (or
none) of the airbags may inflate in a collision. The SRS system senses the force of
the collision on the car and adapts accordingly so that one or more airbags is
deployed.
The airbags have a function whereby their
capacities are adapted to the collision force
to which the car is subjected.
01 Safety
Airbags
Airbag on the driver's side
The car has an airbag to supplement the protection afforded by the seatbelt on the driver's
side. It is folded up into the centre of the steering wheel. The steering wheel is marked SRS
AIRBAG.
G020113
WARNING
Location of the passenger airbag in left-hand drive
and right-hand drive cars.
WARNING
Do not put objects in front of or above the
instrument panel where the passenger airbag is located.
The seatbelts and airbags interact. If a seatbelt is not used or is used incorrectly, this
may diminish the protection provided by the
airbag in the event of a collision.
01
WARNING
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag
is activated.1
Never allow anybody to stand or sit in front
of the front passenger seat. No one shorter
than 140 cm should ever sit in the front passenger seat if the airbag is activated.
Failure to follow the advice given above can
endanger life.
Passenger airbag
The car has an airbag to supplement the protection afforded by the seatbelt on the passenger side. It is folded up into a compartment
above the glovebox. The cover panel is marked
SRS AIRBAG.
WARNING
To minimise the risk of injury if the airbag
deploys, passengers must sit as upright as
possible with their feet on the floor and
backs against the backrest. Seatbelts must
be secured.
1
For information on activated/deactivated airbag, see page 24.
23
01 Safety
01
Activating/deactivating the airbag*
Key switch off - PACOS*
General information
The airbag for the front passenger seat can be
deactivated if the car is equipped with a switch,
PACOS (Passenger Airbag Cut Off Switch). For
information on how to activate/deactivate, see
under the heading Activating/deactivating.
Key switch off/switch
The switch for the passenger airbag (PACOS)
is located on the passenger end of the instrument panel and is accessible when the passenger door is open, (see under the heading,
Activating/deactivating).
Check that the switch is in the required position. Volvo recommends that the key blade is
used to change position.
For information on the key blade, see
page 120.
WARNING
WARNING
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag
is activated. Failure to follow this advice
could endanger the life of the child.
WARNING
If the car is equipped with a front passenger
airbag, but does not have PACOS, then the
airbag will always be activated.
WARNING
Do not allow anyone to sit in the front passenger seat if the text message in the rearview mirror indicates that the airbag is deactivated, and if the warning symbol for the
airbag system is also displayed on the combined instrument panel. This indicates that
there has been a severe malfunction. Visit a
workshop as soon as possible. Volvo recommends that you contact an authorised
Volvo workshop
Failure to follow the advice given above can
endanger life.
24
Activating/deactivating
* Option/accessory, for more information, see Introduction.
Switch location
The airbag is activated. With the switch in
this position, persons taller than 140 cm
can sit in the front passenger seat, but
never children in a child seat or on a
booster cushion.
The airbag is deactivated. With the switch
in this position, children in a child seat or
on a booster cushion can sit in the front
passenger seat, but never persons taller
than 140 cm.
01 Safety
Activating/deactivating the airbag*
01
A text message in the rearview mirror indicates
that the airbag for the front passenger seat is
deactivated (see preceding illustration).
WARNING
Activated airbag (passenger seat):
Never place a child in a child seat or on a
booster cushion on the front passenger seat
when the airbag is activated. This applies to
everyone shorter than 140 cm.
Deactivated airbag (passenger seat):
No one taller than 140 cm should ever sit in
the front passenger seat when the airbag is
deactivated.
Failure to follow the advice given above can
endanger life.
G027050
Message
Indicator showing that the passenger airbag is
deactivated.
* Option/accessory, for more information, see Introduction.
25
01 Safety
Side airbags (SIPS bags)
Side airbag
WARNING
Volvo recommends that repairs are only
carried out by an authorised Volvo
workshop. Defective work in the SIPSbag system could cause malfunction
and result in serious personal injury.
•
Do not place any objects in the area
between the outside of the seat and the
door panel, since this area is required
by the side airbag.
•
Volvo recommends the use only of car
seat covers approved by Volvo. Other
seat covers may impede the operation
of the side airbags.
•
Side airbags are a supplement the seatbelts. Always use a seatbelt.
G020118
•
Side airbag locations.
In a side impact collision a large proportion of
the collision force is transferred by the SIPS
(Side Impact Protection System) to beams, pillars, the floor, the roof and other structural
parts of the body. The side airbags at the driver's and front passenger seats protect the
chest area and are an important part of the
system. The side airbags are located in the
front seat backrests.
1
26
Child seats and side airbags
The protection provided by the car to children
seated in a child seat or on a booster cushion
is not diminished by the side airbag.
A child seat or booster cushion can be placed
on the front passenger seat provided that the
car does not have an activated1 passenger airbag.
For information on activated/deactivated airbag (SRS), see page 24.
Location
G025315
01
Driver's seat, left-hand drive
The SIPS bag system consists of side airbags
and sensors. A sufficiently violent collision trips
the sensors and the side airbags are inflated.
01 Safety
01
G025316
Side airbags (SIPS bags)
Front passenger seat, left-hand drive
The airbag inflates between the occupant and
the door panel and thereby cushions the initial
impact. The airbag deflates when compressed
by the collision. The side airbag is normally only
deployed on the side of the collision.
27
01 Safety
01
Inflatable Curtain (IC)
Properties
WARNING
Never hang or attach heavy items onto the
handles in the roof. The hook is only
designed for light clothing (not for solid
objects such as umbrellas for example).
G027047
Do not screw or install anything onto the
car's headlining, door pillars or side panels.
This could compromise the intended protection. Volvo recommends that you only
ever use Volvo genuine parts that are
approved for placement in these areas.
The inflatable curtain IC (Inflatable Curtain) is a
part of SIPS and the airbags. It is fitted in the
headlining along both sides of the roof and
protects the car's occupants sitting in the outer
seats. A sufficiently violent collision trips the
sensors and the inflatable curtain is inflated.
The inflatable curtain helps to prevent the
driver and passengers from striking their heads
on the inside of the car during a collision.
28
WARNING
Do not load the car higher than 50 mm under
the top edge of the side windows. Otherwise, the intended protection of the inflatable curtain, which is concealed in the headlining, may be compromised.
WARNING
The inflatable curtain is a supplement to the
seatbelts.
Always use a seatbelt.
01 Safety
WHIPS
01
G020347
Protection against whiplash injury – WHIPS
The whiplash protection system (WHIPS) consists of energy absorbing backrests and specially designed head restraints in the front
seats. The system is actuated by a rear-end
collision, where the angle and speed of the collision, and the nature of the colliding vehicle all
have an influence.
Properties of the seat
When the WHIPS system is deployed, the front
seat backrests are lowered backward to alter
the seating position of the driver and front seat
passenger. This reduces the risk of whiplash
injury.
The WHIPS system is a supplement to the
seatbelts. Always use a seatbelt.
The protection provided by the car to children
seated in a child seat or on a booster cushion
is not diminished by the WHIPS system.
Correct seating position
WARNING
WARNING
WHIPS system and child seats/booster
cushions
Never modify or repair the seat or WHIPS
system yourself. Volvo recommends that
you contact an authorised Volvo workshop.
For the best possible protection, the driver and
front seat passenger should sit in the centre of
the seat with as little space as possible
between the head and the head restraint.
``
29
01 Safety
01
WHIPS
Do not obstruct the WHIPS system
WARNING
If a seat has been subjected to extreme
forces, such as due to a rear-end collision,
the WHIPS system must be checked. Volvo
recommends that you contact an authorised Volvo workshop.
G020125
G020126
Part of the WHIPS system's protective
capacity may have been lost even if the
seats appear to be undamaged.
Do not leave any objects on the floor behind the
driver's seat/passenger seat that may prevent the
WHIPS system from functioning.
WARNING
Do not squeeze rigid objects between the
rear seat cushion and the front seat backrest. Make sure you do not to obstruct the
function of the WHIPS system.
30
Do not place objects in the rear seat that may prevent the WHIPS system from functioning.
WARNING
If a rear seat backrest is folded down, the
corresponding front seat must be moved
forward so that it does not touch the folded
backrest.
Volvo recommends that you contact an
authorised Volvo workshop to have the system checked even after a minor rear-end
collision.
01 Safety
Roll-over protection - ROPS
01
Function
Volvo's Roll-Over Protection System (ROPS)
has been designed to reduce the risk of the car
overturning and to provide the best possible
protection in the event of such an accident.
The system consists of:
• A stabiliser system, RSC (Roll Stability
Control) that minimises the risk of overturning during sudden evasive manoeuvres or the like or if the car skids.
• Increased protection for the driver and
passengers through a reinforced body,
inflatable curtains and seatbelt tensioners
in all seats. See also pages 19 and 28.
The RSC system uses a gyro sensor which
registers changes in the car's lateral inclination
angle. This information is then used to calculate the risk for overturning. If a risk is detected,
the DSTC system is engaged, engine speed is
reduced and one or more wheels are braked
until the car returns to a stable position.
For more information on the DSTC system, see
page 149.
WARNING
Under normal driving conditions, the RSC
system improves the car's road safety, but
this must not be taken as a reason to
increase speed. Always follow the usual
precautions for safe driving.
31
01 Safety
When the systems deploy
01
A
System
Triggered
Seatbelt tensioner
In a frontal collision and/or overturning.
Airbags SRS
In a frontal collisionA
Side airbags SIPS
In a side-impact accidentA
Inflatable Curtain IC
In a side-impact accident and/or overturningA.
Whiplash protection WHIPS
In a rear-end collision.
RSC
During sudden evasive manoeuvres or the like or if the car skids.
The bodywork of the car could be greatly deformed in a collision without airbag deployment. A number of factors such as the rigidity and weight of the object hit, the speed of the car, the angle of
the collision etc. affects how the different safety systems of the car are activated.
If the airbags have deployed, the following is
recommended:
• Recovering the car. Volvo recommends
that you have it conveyed to an authorised
Volvo workshop for repair. Do not drive
with deployed airbags.
• Volvo recommends that you engage an
authorised Volvo workshop to handle the
replacement of components in the car's
safety systems.
• Always contact a doctor.
32
NOTE
The SRS, SIPS, IC and belt tensioner systems are deployed only once during a collision.
WARNING
The airbag control module is located in the
centre console. If the centre console is
drenched with water or other liquid, disconnect the battery cables. Do not attempt to
start the car since the airbags may deploy.
Recovering the car. Volvo recommends that
you have it conveyed to an authorised Volvo
workshop.
WARNING
Never drive with deployed airbags. They
can make steering difficult. Other safety
systems may also be damaged. The smoke
and dust created when the airbags are
deployed can cause skin and eye irritation/
injury after intensive exposure. In case of
irritation, wash with cold water. The rapid
deployment sequence and airbag fabric
may cause friction and skin burns.
01 Safety
Child safety
Children should sit comfortably and
safely
Volvo recommends that children travel in rearfacing child seats until as late an age as possible, at least until 3-4 years of age, and then
front-facing booster cushions/child seats up to
10 years of age.
NOTE
In the event of questions when fitting child
safety products, contact the manufacturer
for clearer instructions.
Child seats
Location of child seats
You may place:
• a child seat/booster cushion on the front
passenger seat, provided the passenger
airbag is not activated1.
NOTE
• one or more child seats/booster cushions
Regulations regarding the placement of
children in cars vary from country to country. Check what does apply.
in the rear seat.
Always fit child seats/booster cushions in the
rear seat if the passenger airbag is activated. A
child in the front passenger seat could suffer
serious injury if the airbag deploys.
G020128
Children of all ages and sizes must always sit
correctly secured in the car. Never allow a child
to sit on the knee of a passenger.
1
Do not attach the straps for the child seat to
the horizontal adjustment bar, springs, rails or
beams under the seat. Sharp edges can damage the straps.
Look in the installation instructions for the child
seat for the correct fitting.
The position of a child in the car and the choice
of equipment are dictated by the child's weight
and size, for more information, see page 34.
Volvo's own child safety equipment is
designed for your car. Volvo recommends that
you use Volvo genuine equipment to best
ensure that the mounting points and attachments are correctly positioned and are sufficiently strong.
01
Child seats and airbags are not compatible.
NOTE
When using other child safety products it is
important to read the installation instructions included with the product.
For information on activating/deactivating the airbag (SRS), see page 24.
``
33
01 Safety
Child safety
01
WARNING
WARNING
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag
(SRS) is activated.2
No one shorter than 140 cm should ever sit
in the front passenger seat if the airbag
(SRS) is activated.
Failure to follow the advice given above can
endanger life.
Label Airbag
Booster cushions/child seats with steel
braces or some other design that could rest
on the seatbelt buckle's opening button
must not be used, as they could cause the
seatbelt buckle to open accidentally.
Do not allow the upper section of the child
seat to rest against the windscreen.
Label fitted on the end face of the instrument panel
on the passenger side, see the illustration on page
24.
Recommended child seats3
Weight
Front seat (with deactivated airbag)
Group 0
Volvo infant seat (Volvo Infant Seat) - rear-facing child seat, secured with the ISOFIX fixture system.
<10 kg
Type approval: E1 04301146
Volvo infant seat (Volvo Infant Seat) - rear-facing child seat, secured with the car's seatbelt
Type approval: E1 04301146
Rear-facing child seat (Child Seat) - rear-facing child seat, secured with the car's seatbelt and straps.
Type approval: E5 03135
Child seats which are universally approved.
2
3
34
For information on activated/deactivated airbag (SRS), see page 24.
For other child seats your car should be included in the manufacturer's enclosed list of vehicles or be universally approved in accordance with the ECE R44 legal requirement.
01 Safety
Child safety
Weight
Front seat (with deactivated airbag)
Group 1
Volvo rear-facing/turnable child seat (Volvo Convertible Child Seat) - rear-facing child seat, secured with the car's seatbelt and
straps.
9 – 18 kg
01
Type approval: E5 04192
Rear-facing child seat (Child Seat) - rear-facing child seat, secured with the car's seatbelt and straps.
Type approval: E5 03135
Britax Fixway – rear-facing child seat, secured with the ISOFIX fixture system and straps.
Type approval: E5 03171
Child seats which are universally approved.
Group 2
15 – 25 kg
Volvo rear-facing/turnable child seat (Volvo Convertible Child Seat) - rear-facing child seat, secured with the car's seatbelt and
straps
Type approval: E5 04192
Volvo rear-facing/turnable child seat (Volvo Convertible Child Seat) - front-facing child seat, secured with the car's seatbelt.
Type approval: E5 04191
Group 2/3
Volvo booster seat with backrest (Volvo Booster Seat with backrest).
15 – 36 kg
Type approval: E1 04301169
Booster cushion with and without backrest (Booster Cushion with and without backrest).
Type approval: E5 03139
``
35
01 Safety
01
Child safety
Weight
Second row of seats, outer seatsA
Group 0
Volvo infant seat (Volvo Infant Seat) rear-facing child seat, secured with the
ISOFIX fixture system.
<10 kg
Second row of seats, centre seatA
Third row of seats in cars seating
seven
Not suitable for this age group.
Type approval: E1 04301146
Volvo infant seat (Volvo Infant Seat) rear-facing child seat, secured with the
car's seatbelt.
Type approval: E1 04301146
36
Rear-facing child seat (Child Seat) - rearfacing child seat, secured with the car's
seatbelt, straps and support legs.
Rear-facing child seat (Child Seat) - rearfacing child seat, secured with the car's
seatbelt, straps and support legs.
Type approval: E5 03135
Type approval: E5 03135
Child seats which are universally
approved.
Child seats which are universally
approved.
Child seats which are universally
approved.
01 Safety
Child safety
Weight
Second row of seats, outer seatsA
Group 1
Volvo rear-facing/turnable child seat
(Volvo Convertible Child Seat) - rear-facing child seat, secured with the car's
seatbelt and straps.
9 – 18 kg
Second row of seats, centre seatA
01
Third row of seats in cars seating
seven
Not suitable for this age group.
Type approval: E5 04192
Rear-facing child seat (Child Seat) - rearfacing child seat, secured with the car's
seatbelt and straps.
Rear-facing child seat (Child Seat) - rearfacing child seat, secured with the car's
seatbelt, straps and support legs.
Type approval: E5 03135
Type approval: E5 03135
Britax Fixway – rear-facing child seat,
secured with the ISOFIX fixture system
and straps.
Type approval: E5 03171
Child seats which are universally
approved.
Child seats which are universally
approved.
Child seats which are universally
approved.
``
37
01 Safety
Child safety
01
Weight
Second row of seats, outer seatsA
Group 2
Volvo rear-facing/turnable child seat
(Volvo Convertible Child Seat) - rear-facing child seat, secured with the car's
seatbelt and straps
15 – 25 kg
Second row of seats, centre seatA
Third row of seats in cars seating
seven
Not suitable for this age group.
Type approval: E5 04192
Group 2/3
15 – 36 kg
Volvo rear-facing/turnable child seat
(Volvo Convertible Child Seat) - front-facing child seat, secured with the car's
seatbelt.
Volvo rear-facing/turnable child seat
(Volvo Convertible Child Seat) - front-facing child seat, secured with the car's
seatbelt.
Type approval: E5 04191
Type approval: E5 04191
Volvo booster seat with backrest (Volvo
Booster Seat with backrest).
Volvo booster seat with backrest (Volvo
Booster Seat with backrest).
Volvo booster seat with backrest (Volvo
Booster Seat with backrest).
Type approval: E1 04301169
Type approval: E1 04301169
Type approval: E1 04301169
Booster cushion with and without backrest (Booster Cushion with and without
backrest).
Booster cushion with and without backrest (Booster Cushion with and without
backrest).
Booster cushion with and without backrest (Booster Cushion with and without
backrest).
Type approval: E5 03139
Type approval: E5 03139
Type approval: E5 03139
Integrated booster cushion (Integrated
Booster Cushion) - available as a factory
fitted option.
Type approval: E5 03167
A
38
In cars seating seven, the seat row must be in its rearmost position when using a child seat.
01 Safety
Child safety
Integrated booster cushion*
WARNING
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag
(SRS) is activated.
No one shorter than 140 cm should ever sit
in the front passenger seat if the airbag
(SRS) is activated.4
Failure to follow the advice given above can
endanger life.
01
Grasp the cushion with both hands and
push it backwards.
Push until the cushion locks in place.
WARNING
The booster cushion must be in the locked
position before the child is placed there.
Check that:
• the seatbelt is locked.
• the seatbelt is in contact with the child's
G031071
Raising the booster cushion
body and is not slack or twisted, and that
the seatbelt is positioned correctly across
the shoulder.
Volvo's integrated booster cushion for the centre rear seat is specially designed to provide
optimum safety for children. Combined with
the regular seatbelts the integrated booster
cushion is approved for children weighing
between 15 and 36 kg.
• the lap belt is low over the pelvis for optimum protection.
• the seatbelt does not lie across the child's
throat or below the shoulder.
• Carefully adjust the position of the head
G020808
restraint to suit the child.
Pull that handle to raise the booster cushion.
4
For information on activated/deactivated airbag (SRS), see page 24.
``
* Option/accessory, for more information, see Introduction.
39
01 Safety
01
Child safety
Pull the handle.
WARNING
Volvo recommends that repair or replacement is only carried out by an authorised
Volvo workshop. Do not make any modifications or additions to the booster cushion.
If an integrated booster cushion has been
subjected to a major load, such as in conjunction with a collision, the entire booster
cushion must be replaced. Even if the
booster cushion appears to be undamaged,
it may not afford the same level of protection. The booster cushion must also be
replaced if it is heavily worn.
Lowering the booster cushion
Lower the cushion and press until it locks.
NOTE
Remember to stow away the booster cushion before lowering the rear seat backrest.
Child safety locks, rear doors
G015268
G014507
* Option/accessory, for more information, see Introduction.
The location of the mounting points is indicated
by symbols in the backrest upholstery (see preceding illustration).
Press the seat cushion down to access the
mounting points.
NOTE
The controls for operating the rear door power
windows and the rear door opening handles
can be blocked from opening from the inside.
For more information see page 125.
ISOFIX fixture system for child seats*
40
Mounting points for the ISOFIX fixture system
are concealed behind the lower section of the
rear seat backrest, in the outer seats.
The ISOFIX fixture system is an accessory
for the passenger seat.
Always follow the manufacturer's installation
instructions when connecting a child seat to
the ISOFIX mounting points.
01 Safety
Child safety
Mounting points for child seat
Fold the backrest forward to access the
mounting points. For detailed information on
how the child seat should be tensioned in the
upper mounting points, see the seat manufacturer's instructions.
Extra locking function in seatbelt (ALR/
ELR)5
01
This function is automatically deactivated
when the seatbelt is released from the buckle
and retracts back to its starting position.
If there are any problems with installation of
child safety products, contact the manufacturer for clearer installation instructions.
G027032
The seatbelt in the centre of the second row of
seats has an extra locking function (ALR/ELR).
The locking function helps to hold the belt taut
in order to facilitate child seat installation.
The car is equipped with upper mounting
points for child seats. These mounting points
are located on the rear of the rear seats.
The upper mounting points are primarily
intended for use with front-facing child seats.
Volvo recommends that small children should
sit in rear-facing child seats to as late an age
as possible.
NOTE
When installing a child seat with the help of the
seatbelt:
1. Secure the seatbelt in the child seat following the instructions of the child seat
manufacturer.
2. Pull out the entire seatbelt.
3. Lock the seatbelt by inserting the locking
tab in the buckle. A clear "click" indicates
that the seatbelt has locked.
4. Allow the seatbelt mechanism to retract
the seatbelt while stretching it around the
child seat. A mechanical sound will be
audible from the seatbelt. This is normal.
These mounting points are only on the second row of seats in cars seating seven.
5
Automatic Locking Retractor/Emergency Locking Retractor.
41
Overview, left-hand drive car..................................................................
Overview, right-hand drive car................................................................
Driver's door control panel.....................................................................
Combined instrument panel....................................................................
Indicator and warning symbols...............................................................
Information display..................................................................................
Switches in the centre console...............................................................
Lighting panel..........................................................................................
Left-hand stalk switch.............................................................................
Trip computer*........................................................................................
Right-hand stalk switch..........................................................................
Cruise control*........................................................................................
Parking brake, electrical socket, etc.......................................................
Power windows.......................................................................................
Windows, rearview and door mirrors......................................................
Power sunroof*.......................................................................................
44
46
48
49
51
54
55
58
60
61
63
65
67
69
71
76
HomeLinkŸ *............................................................................................ 78
42
* Option/accessory, for more information, see Introduction.
INSTRUMENTS AND CONTROLS
02 Instruments and controls
Overview, left-hand drive car
G000000
02
44
02 Instruments and controls
Overview, left-hand drive car
Lighting panel
Cruise control
Panel vents
Direction indicators, dipped-main beam
switch, READ button
Display
Temperature gauge
Odometer, trip meter, cruise control
Speedometer
Direction indicators
Tachometer
Outside temperature, clock, gear position
02
Parking brake
Parking brake release
Switches, reading lamps
Passenger compartment lighting
Sunroof control
Seatbelt reminder
Rearview mirror
Fuel gauge
Indicator and warning symbols
Panel vents
Glovebox
Hazard warning flashers
Audio system
Climate control
Windscreen wipers
Keypad for phone/audio
Combined instrument panel
Horn
45
02 Instruments and controls
Overview, right-hand drive car
G027038
02
46
02 Instruments and controls
Overview, right-hand drive car
Lighting panel
Horn
Panel vents
Combined instrument panel
Indicator and warning symbols
Phone/Audio keypad
Fuel gauge
Windscreen wipers
Outside temperature, clock, gear position
Parking brake release
Tachometer
Switches, reading lamps
Direction indicators
Passenger compartment lighting
Speedometer
Sunroof control
Odometer, trip meter, cruise control
Seatbelt reminder
Temperature gauge
Rearview mirror
02
Display
Panel vents
Glovebox
Hazard warning flashers
Audio system
Climate control
Direction indicators, dipped-main beam
switch, READ button
Parking brake
Cruise control
47
02 Instruments and controls
Driver's door control panel
Control panel
G029570
02
Lock button, for all doors
Blocking power windows in the rear doors
Power window controls
Door mirror control
48
02 Instruments and controls
Combined instrument panel
G026973
02
Temperature gauge – Displays the temperature of the engine cooling system. A
message will appear on the display if the
gauge goes into the red zone. Bear in mind
that extra lights placed in front of the air
intake reduce the cooling capacity of the
system.
Display – The display shows information
and warning messages.
Speedometer – Shows the speed of the
car.
Trip meters T1 and T2 – Used for measuring short distances. The right-hand digit
displays tenths of a kilometre. Press the
button for more than 2 seconds to reset.
Switch between trip meters with one quick
press of the button.
Automatic gearbox indicator – The
selected gear position is displayed here.
Cruise control indicator.
Outside temperature gauge – When the
temperature lies between +2 °C to 5 °C, a
snowflake symbol illuminates in the display. This warns of icy roads. If the car has
been stationary, the gauge may display a
reading that is too high.
Odometer – The odometer indicates the
total distance the car has travelled.
Main beam indicator
Warning symbol – If a fault arises, the symbol illuminates and a message is shown in
the display.
Tachometer – Indicates engine speed in
thousands of revolutions per minute (rpm).
Do not allow the tachometer gauge to enter
the red zone.
Knob for clock – Turn the knob to adjust
the time.
When the lamp in the instrument illuminates the level in the fuel tank is low, refuel
as soon as possible. See also Trip computer page 61.
``
49
02 Instruments and controls
Combined instrument panel
Indicator and warning symbols
02
50
Direction indicators – left/right
02 Instruments and controls
Indicator and warning symbols
Functionality check, symbols
If the engine does not start within
5 seconds, all symbols extinguish
except the symbols for a fault in
the car's emissions system and for
low oil pressure.
Certain symbols may have no
function, depending on the car's
specifications.
These symbols illuminate with a
red or amber glow depending on
the severity of the fault.
02
Red symbol
1. Stop the car in a safe place. Do not drive
the car further. Do not drive the car further.
2. Read the information on the display.
Symbols in the centre of the instrument
panel
3. Rectify in accordance with the instructions
in the display or contact a workshop. Volvo
recommends that you seek assistance
from an authorised Volvo workshop.
Symbol and message text are visible until the
fault has been rectified.
All indicator and warning symbols1 illuminate
when the remote control key is turned to position II before starting. This is to check that the
symbols are working. When the engine starts,
all the symbols should go out except the handbrake symbol, which only goes out when the
brake is disengaged.
Yellow symbol
Read the message in the display. Action.
The message text is cleared using the READ
button, see page 54, or it disappears automatically after 2 minutes.
NOTE
When the message text TIME FOR
REGULAR SERVICE is shown, the symbol
and message text are cleared using the
READ button, or disappear automatically
after 2 minutes.
1
For certain engine variants, the symbol for low oil pressure is not used. Warnings are given via display text, see page 203.
``
51
02 Instruments and controls
Indicator and warning symbols
Indicator symbols
02
workshop to have the brake system
checked.
ABS fault
If the BRAKE and ABS symbols
illuminate at the same time, there
may be a fault in the brake force
distribution system.
If this symbol illuminates then the
system is not working. The car's
regular brake system continues to
work, but without the ABS function.
1. Stop the car in a safe place and turn off the
engine.
Fault in brake system
If this symbol illuminates, the brake
fluid level may be too low.
1. Stop the car in a safe place and turn off the
engine.
2. Restart the engine.
• If both symbols extinguish, continue driving.
• If the symbols remain illuminated, check
the level in the brake fluid reservoir, see
page 206.
• If the brake fluid reservoir's level is normal
1. Stop the car in a safe place and check the
level in the brake fluid reservoir, see
page 206.
2. If the reservoir level is below MIN then the
car should not be driven further, but recovered instead. Volvo recommends that the
car is transported to an authorised Volvo
2
52
WARNING
If the BRAKE and ABS symbols are illuminated at the same time, there is a risk that
the rear end will skid during heavy braking.
Seatbelt reminder
2. Restart the engine.
3. Volvo recommends that drive to an authorised Volvo workshop to have the ABS system checked if the symbol remains illuminated.
mended by Volvo to have the brake system
checked.
but the symbols are still illuminated, the car
can be driven, with great care, to an
authorised workshop recommended by
Volvo to have the brake system checked.
• If the level in the brake fluid reservoir is
below MIN then the car should not be
driven any further. Have the car transported to an authorised workshop recom-
For certain engine variants, the symbol for low oil pressure is not used. Warnings are given via display text, see page 203.
This symbol illuminates if someone
in a front seat has not put on their
belt or if someone in a rear seat has
taken off their seatbelt.
Low oil pressure2
If this symbol illuminates during
driving then the engine's oil pressure is too low. Stop the engine
immediately and check the engine
oil level, top up if necessary. If the
symbol illuminates and the oil level is normal,
contact an authorised workshop recommended by Volvo.
02 Instruments and controls
Indicator and warning symbols
Emissions system
Parking brake applied
If the symbol illuminates then it
may be due to a fault in the car's
emissions system. Volvo recommends that you drive to an authorised Volvo workshop for inspection.
The symbol illuminates when the
parking brake is depressed.
Always depress the parking brake
to the bottom position.
NOTE
Airbags – SRS
If this symbol remains illuminated
or illuminates while driving, it
means a fault has been detected in
the seatbelt buckle, SRS, SIPS, or
IC system. Volvo recommends that
drive directly to an authorised Volvo workshop
for inspection.
The symbol illuminates irrespective of how
hard the parking brake is depressed.
Rear fog lamp
This symbol is illuminated when
the fog lamp is on.
Reminder – doors not closed
If one of the doors or the tailgate is not properly
closed the driver will be reminded of this.
Low speed
If the car moves at a speed less than
about 7 km/h, the information symbol illuminates and DRIVER DOOR OPEN ,
PASSENGER DOOR OPEN ,LEFT REAR
DOOR OPEN or RIGHT REAR DOOR OPEN
is shown in the display at the same time. Stop
the car safely as soon as possible and close the
door or bonnet.
High speed
If the car is moving faster than
about 7 km/h then the symbol illuminates and one of the texts indicated in the previous paragraph
appears in the display at the same
Alternator not charging
If this symbol illuminates while
driving, a fault has occurred in the
electrical system. Volvo recommends that you visit an authorised
Volvo workshop.
Engine preheater (diesel)
This symbol illuminates during
engine preheating. Preheating
occurs when the temperature is
below 2 °C. The car can be started
once the symbol goes out.
Indicator symbol for trailer
This symbol flashes when the
direction indicators are used and
the trailer is connected. If the symbol does not flash then one of the
lamps on the trailer or the car is
faulty.
02
time.
Tailgate reminder
If the tailgate is open, TAILGATE OPEN will
appear on the display.
Stability system STC or DSTC
For information on the system's
functions and symbols, see
page 150.
53
02 Instruments and controls
Information display
Messages
G026979
02
When a warning or indicator symbol illuminates, it is supplemented by a message
appearing on the display.
Press the READ button (A).
Switch between messages with the READ button. Fault messages are stored in the memory
until the fault is rectified.
NOTE
Message
Specification
Message
Specification
STOP SAFELYA
Stop the car in a safe
manner and turn off
the engine. Serious
risk of damage.
TIME FOR REGULAR SERVICE
STOP ENGINEA
Stop the car in a safe
manner and turn off
the engine. Serious
risk of damage.
SERVICE
URGENTA
Volvo recommends
that you engage an
authorised Volvo
workshop to check
the car immediately.
Time for regular
service. Volvo recommends that you
engage an authorised Volvo workshop to carry out the
service. The timing
is determined by the
number of kilometres driven, number
of months since the
last service and
engine running time.
SOOT FILTER
FULL SEE MANUAL
Diesel particle filter
requires regeneration, see page 138.
STC/DSTC SPIN
CONTROL OFF
The function of the
stability and traction
control system is
reduced, see
page 149 for more
variants.
SEE
MANUALA
SERVICE
REQUIREDA
Read the owner's
manual.
Volvo recommends
that you engage an
authorised Volvo
workshop to check
the car as soon as
possible.
A
If a warning message appears while you are
using the trip computer, the message must
be read (press READ) before the previous
activity can be resumed.
54
Part of message, shown together with information on where
the problem has arisen.
02 Instruments and controls
Switches in the centre console
Switch
G026944
02
Child safety locks in the rear doors*
NOTE
The order of the buttons may vary.
Air conditioning in the rear of the
passenger compartment*
Press the button to activate the
air conditioning in the rear of
the passenger compartment.
Rear passenger compartment
air conditioning is deactivated
when the ignition is switched
off.
Retractable power door mirrors*
Activating or deactivating the
electric child safety locks in the
rear doors. The remote control
key must be in position I or II.
When the child safety locks are
activated, the lamp in the button illuminates. A message is shown in the display when the child safety locks are activated
or deactivated, see page 125.
Used to fold in the door mirrors
if they are folded out or to fold
them out if they are folded in.
Proceed as follows if a door mirror has been
accidentally folded in or out:
1. Manually adjust the appropriate door mirror to its normal position.
2. Turn the remote control key to position II.
``
* Option/accessory, for more information, see Introduction.
55
02 Instruments and controls
Switches in the centre console
3. Fold the door mirror inward and then outward using the button.
02
The door mirrors have now returned to their
original fixed positions.
Park Assist*
The system is always activated
when the car is started. Press
the button to deactivate/reactivate the parking assistance
system. See also page 151.
Deactivation of the deadlocks* and
detectors
Use this button when you wish
to switch off the deadlock function (doors cannot be opened
from the inside when locked).
This button can also be used
when deactivating the alarm
system's movement and tilt detectors*. The
lamp illuminates when these systems are shut
down/deactivated, see pages 124 and 128.
Active Xenon headlamps*
If the car is equipped with
active Xenon headlamps
(Active Bending Lights, ABL)
the light from the headlamps
follows the steering wheel
movement during driving. The
function is activated automatically when the
car is started and can be deactivated/activated
by pressing the button. The lamp in the button
illuminates when the function is activated
Shifting headlamp pattern for right/lefthand traffic
Hold the button depressed for at least 5 seconds. The car must be stationary when the
headlamp pattern is shifted. The message
HEADLIGHTS SET FOR RH TRAFFIC or
HEADLIGHTS SET FOR LH TRAFFIC is
shown in the display. For more information and
adapting headlamp pattern for halogen or Dual
Xenon headlamps, see page 168.
Electric socket/Cigarette lighter*
The electrical socket can be
used for 12 V accessories, such
as mobile phone chargers and
coolers.
Auxiliary lamps*
Use this button to switch the
auxiliary lamps on with main
beam or to switch them off.
The remote control key must be at least in
position I so that the socket can supply power.
56
* Option/accessory, for more information, see Introduction.
The cigarette lighter is activated by pushing in
the button. The button pops out when the
lighter is hot. Pull out the lighter and light a cigarette on the heated coils. For safety reasons,
always keep the cover in place when the
socket is not in use. Maximum current tap 10 A.
WARNING
Always leave the plug in the socket when
the socket is not in use.
BLIS - Blind Spot Information System*
Press the button to deactivate
or reactivate the function. see
page 153 for further information.
02 Instruments and controls
Switches in the centre console
Hazard warning flashers
Rear window and door mirror defrosters
Heating is used to quickly
remove misting and ice from
the rear window and door mirrors. Press the switch to start
defrosting the rear window and
door mirrors. The lamp in the
switch illuminates. The light in
the switch is lit. Defrosting is
automatically disconnected
after about 12 minutes.
AM FM
CD
LUM
VO E
POWER
*
3
DEF
5
6
JKL
MNO
8
9
TUV WXYZ
0
#
G027096
2
ABC
1
4
GHI
7
PQRS
02
Use the hazard warning flashers (all direction
indicators flash) when the car is stopped where
it could be a traffic hazard or obstruction. Press
the button to activate the function.
Heated front seats
For heated front seats, see
page 88 or 90 for further
information.
NOTE
Regulations regarding the use of hazard
warning flashers vary from country to country.
57
02 Instruments and controls
Lighting panel
Headlamps
Position
02
Specification
G027100
Automatic/deactivated dipped
beam. Only main beam flash.
Position/parking lamps
Position/parking lamps
Position/parking lamps can be switched on
irrespective of remote control key position.
Automatic dipped beam. Main
beam and main beam flash
work in this position.
Automatic dipped beam*
Turn the headlamp control (1) to the centre
position.
When the remote control key is in position II the
position/parking lamps and number plate lighting are always switched on.
Thumbwheel for headlamp levelling
Dipped beam comes on automatically when
the remote control key is turned to position II,
except when the headlamp control (1) is in the
centre position. If necessary, the automatic
dipped beam can be deactivated. Volvo recommends that you engage an authorised Volvo
workshop to have it deactivated.
Rear fog lamp
Automatic dipped beam, main beam
1. Turn the remote control key to position II.
1. Turn the remote control key to position II.
2. Turn the headlamp control (1) to one of the
end positions.
Light switches
Fog lamps*
Thumbwheel for adjusting instrument lighting
2. Dipped beam is activated by means of
turning the headlamp control (1) clockwise
to the end position.
3. Main beam is activated by means of moving the left-hand stalk switch towards the
steering wheel to the end position and
releasing it, see page 60.
58
The lamps are switched off automatically when
the remote control key is turned to position I or
0.
* Option/accessory, for more information, see Introduction.
Headlamp levelling
The load in the car changes the vertical alignment of the headlamp beam, which could dazzle oncoming motorists. Avoid this by adjusting
the height of the beam.
3. Roll the thumbwheel (3) up or down
respectively to raise or lower beam alignment.
Cars with Xenon headlamps* have automatic
headlamp levelling, so there is no thumbwheel
(3).
02 Instruments and controls
Lighting panel
Instrument lighting
The instrument lighting is switched on when
the remote control key is in position II and the
headlamp control (1) is in one of the end positions. The lighting is automatically dimmed
during the day and can be controlled manually
at night.
The rear fog lamp indicator symbol on the combined instrument panel and the light in the button illuminate when the rear fog lamp is
switched on.
02
Active Xenon headlamps*
Roll the thumbwheel (5) up or down for brighter
or dimmer lighting.
Fog lamps
NOTE
Regulations for use of fog lamps vary from
country to country.
The front fog lamps can be switched on along
with the headlamps or the position lamps/parking lamps.
Press the button (2).
The light in the button illuminates when the
front fog lamps are switched on.
Rear fog lamp
The rear fog lamp can only be switched on with
the headlamps or the front fog lamps.
G020789
Fog lamps*
Headlamp pattern for active/non-active headlamps.
If the car is equipped with active Xenon headlamps (Active Bending Lights, ABL) the light
from the headlamps follows the steering wheel
movement during driving. The function is activated automatically when the car is started and
can be deactivated/activated using the button
in the centre console, see page 56.
Press the button (4).
* Option/accessory, for more information, see Introduction.
59
02 Instruments and controls
Left-hand stalk switch
Stalk switch positions
Direction indicators
Continuous flash sequence
02
Move the stalk switch up or down to end
position (2).
The stalk switch remains in its end position and
is moved back manually, or automatically by
steering wheel movement.
Short flash sequence
G026954
Short flash sequence, direction indicators
Continuous flash sequence, direction indicators
Main beam flash
Home safe lighting and switching of
dipped and main beam
Move the stalk switch up or down to position (1) and release, the stalk switch then
returns to its home position, or move the
stalk switch to position (2) and move it
directly back to the home position.
The direction indicators flash three times. Short
flash sequence interrupted immediately if indicating is started in the opposite direction.
The remote control key must be in position II
for main beam to be switched on.
2. Move the stalk switch towards the steering
wheel to the end position (4) and release.
60
Factory settings.
Move the stalk switch gently towards the
steering wheel to position (3).
Main beam comes on until the stalk switch is
released.
Home safe lighting
Some of the exterior lighting can be kept
switched on to work as home safe lighting after
the car has been locked. The standard delay is
30 seconds1, but can be changed to 60 or
90 seconds.
1. Remove the remote control key from the
ignition switch.
2. Move the stalk switch towards the steering
wheel to the end position (4) and release.
3. Get out of the car and lock the door.
Switching, main and dipped beam
1. Turn the headlamp control clockwise to the
end position, see page 58.
1
Main beam flash
02 Instruments and controls
Trip computer*
General information
NOTE
If a warning message interrupts while you
are using the trip computer, this message
must be acknowledged. Acknowledge by
pressing the READ button and revert to the
trip computer function.
The trip computer displays the following information:
RESET - resets
AVERAGE SPEED
G026956
Thumbwheel - browse between menus
and options in the trip computer list
READ - confirms
Controls
To scroll through trip computer information
turn the thumbwheel (B) either up or down in
steps. Continue turning to return to the starting
point.
AVERAGE
The average fuel consumption since the last
reset. Reset using RESET.
There may be a slight error in the reading if
a fuel-driven parking heater* has been used.
--- KM/H AVERAGE SPEED
KILOMETRES TO EMPTY TANK
--.- KM/L INSTANTANEOUS
--.- KM/L AVERAGE
--- KILOMETRES TO EMPTY TANK
DSTC ON , see page 149
--- MPH ACTUAL SPEED 1*
When the ignition is switched off, the average
speed is stored and used as the basis of the
new value when you continue driving. Reset
using the RESET button.
INSTANTANEOUS
Current fuel consumption is calculated every
second. The information on the display is
updated every couple of seconds. When the
1
2
02
NOTE
Functions
•
•
•
•
•
•
car is stationary, "----" appears on the display.
During the period for regeneration2 fuel consumption may increase, see page 138.
The calculation is based on the average fuel
consumption over the last 30 km and the
remaining driveable fuel quantity. The display
shows the approximate distance that can be
driven with the fuel quantity remaining in the
tank. No guaranteed range remains when the
display shows "--- KILOMETRES TO EMPTY
TANK ". Refuel as soon as possible.
NOTE
There may be a slight error in the reading if
a fuel-driven parking heater* has been used
or if driving style has been changed.
Only in certain markets.
Only applies to diesel cars with particle filter.
``
* Option/accessory, for more information, see Introduction.
61
02 Instruments and controls
Trip computer*
MPH ACTUAL SPEED.*1
02
Current speed is displayed in mph if the speedometer is graduated in km/h. If it is graduated
in mph then the current speed is shown in mph.
Resetting
1. Select --- KM/H AVERAGE SPEED or
--.- KM/L AVERAGE
2. Press and hold the RESET button (C) for at
least five seconds to reset the average
speed and average consumption at the
same time.
1
62
Only in certain markets.
* Option/accessory, for more information, see Introduction.
02 Instruments and controls
Right-hand stalk switch
Windscreen wipers
Rain sensor*
Intermittent wiping
You can set a suitable delay
between the sweeps. Turn the
thumbwheel up for a shorter interval between sweeps. Turn it down
to increase the delay.
Continuous wiping
The wipers sweep at normal
speed.
The wipers sweep at high speed.
The rain sensor automatically activates the
windscreen wipers based on how much water
it detects on the windscreen. The sensitivity of
the rain sensor can be adjusted using the
thumbwheel.
02
Turn the thumbwheel upwards for higher sensitivity and downwards for lower sensitivity. (An
extra sweep is made when the thumbwheel is
turned upwards.)
G026953
On/Off
Wiper/washer function – windscreen.
Thumbwheel
IMPORTANT
Before activating the wipers during winter ensure that the wiper blades are not frozen
in and that any snow or ice on the windscreen (and rear window) is scraped away.
Rain sensor - on/off
Windscreen wipers off
The windscreen wipers are off
when the stalk switch is in position
0.
IMPORTANT
Use plenty of washer fluid when the wipers
are cleaning the windscreen. The windscreen must be wet when the windscreen
wipers are operating.
When activating the rain sensor, the remote
control key must be in position I or II and the
windscreen wiper stalk switch must be in position 0 (not activated).
To activate the rain sensor:
Press the button. A lamp in the button illuminates to indicate that the rain sensor is
active.
To turn the rain sensor off, either:
• Press the button. The lamp in the button
goes out.
• Press the stalk switch downward to
Single sweep
Raise the stalk switch to make a
single sweep.
another wiper program. If the stalk switch
is raised, the rain sensor will remain active,
the wipers make an extra sweep and then
return to rain sensor mode when the stalk
is released to position 0.
``
* Option/accessory, for more information, see Introduction.
63
02 Instruments and controls
Right-hand stalk switch
02
The rain sensor is automatically deactivated
when the remote control key is removed from
the ignition switch or 5 minutes after the ignition is switched off.
IMPORTANT
Reduced washing
If only approx. 1 litre of washer fluid remains in
the reservoir, the supply to the headlamps and
rear window is cut off. This is in order to prioritise visibility through the windscreen.
Intermittent wiping: Depress the top of the
button.
Neutral position: Function deactivated.
Constant speed: Depress the bottom of
the button.
Wiper and washer, rear window
The windscreen wipers could start and be
damaged in an automatic car wash. Deactivate the rain sensor by depressing button
(2) while the remote control key is in position
I or II.
Wiper – reversing
Engaging reverse gear while the windscreen
wipers are on initiates intermittent rear window
wiping.1 If the rear window wiper is already on
at normal speed, no change is made.
Windscreen/headlamp washer
G027127
Move the stalk switch toward the steering
wheel to start the windscreen and headlamp
washers. The wipers will make several more
sweeps once the stalk switch is released.
High-pressure headlamp washing*
High-pressure headlamp washing consumes a
large quantity of washer fluid. To save fluid, the
headlamps are only washed every fifth wash
cycle (within a 10 minute period). When 10
minutes have elapsed following the latest
windscreen washing, the headlamps are again
washed with high-pressure with the first windscreen washing. Turn the stalk switch toward
the steering wheel to wash the windscreen
only.
1
64
Wiper/washer function – rear window.
Move the stalk switch forward to start rear window washing and wiping. The wiper blade
makes several extra sweeps once washing has
finished. The button at the end of the stalk
switch has three positions:
This function (intermittent wiping when reversing) can be deactivated. Volvo recommends that you visit an authorised Volvo workshop to have it deactivated.
* Option/accessory, for more information, see Introduction.
02 Instruments and controls
Cruise control*
Activating
Increasing or decreasing speed
NOTE
A temporary increase in speed (less than
one minute) using the accelerator, such as
while overtaking, does not affect the cruise
control setting. When you release the accelerator, the car will return to the programmed
speed.
02
Temporary disengagement
G027098
G026949
The controls for cruise control are to the left of
the steering wheel.
Setting the desired speed:
1. Press the CRUISE button. CRUISE is
shown on the combined instrument panel.
2. Touch + or – to lock the vehicle speed.
CRUISE-ON is shown.
Cruise control cannot be engaged at speeds
below 30 km/h or above 200 km/h.
1
Increase or decrease the speed by pressing and holding + or –. The speed of the car
when the button is released is set as the
new speed.
A brief press (less than half a second) on + or
– changes the speed by 1 km/h or 1 mph1.
Press 0 to disengage the cruise control
temporarily. CRUISE will be shown on the
combined instrument panel. The speed set
earlier is stored in the memory.
The cruise control is also temporarily disengaged when:
• the brake pedal or clutch pedal is
depressed
• speed falls when travelling uphill to below
25-30 km/h
• the gear selector is moved to position N
• wheel spin or wheel lock-up occurs
• a temporary increase in speed lasts longer
than 1 minute.
Depending on engine type.
``
* Option/accessory, for more information, see Introduction.
65
02 Instruments and controls
Cruise control*
Return to the set speed
Press this button to resume the
previously set speed. CRUISE
ON appears on the combined
instrument panel.
02
Disengaging
66
Press CRUISE to disengage the cruise
control. CRUISE ON clears on the combined instrument panel.
* Option/accessory, for more information, see Introduction.
02 Instruments and controls
Parking brake, electrical socket, etc.
Parking brake
2. Depress the parking brake pedal firmly as
far as possible.
3. Release the foot brake and make sure that
the car is stationary.
02
4. If the vehicle rolls, the parking brake pedal
must be depressed further.
Parking brake, LHD car.
G026994
G026992
5. When parking a vehicle select position 1
(for manual transmission) or P (for automatic transmission).
Parking brake, RHD car.
Parking brake pedal
Handle for releasing parking brake
The parking brake is at floor level, see illustration, and acts on the rear wheels when
depressed.
NOTE
The warning symbol in the combined instrument panel illuminates irrespective of how
hard the parking brake pedal is depressed.
Parking on a hill
If the car is parked facing uphill; turn the wheels
away from the kerb.
If the car is parked facing downhill, turn the
wheels towards the kerb.
WARNING
Get into the habit of always applying the
parking brake when parking on a slope leaving the car in gear, or in P if it has automatic transmission, is not sufficient to hold
the car in all situation.
How to release the parking brake
1. Press the foot brake down firmly.
2. Pull the handle.
How to apply the parking brake
1. Press the foot brake down firmly.
``
67
02 Instruments and controls
Parking brake, electrical socket, etc.
Electrical socket in the rear seat
Steering wheel adjustment
Opening the tailgate
The electrical socket can be used for various
accessories, such as mobile phone chargers
and coolers. It is designed for 12 V. The maximum current is 10 A. For the socket to supply
current, the remote control key must be in at
least position I.
The steering wheel can be adjusted for both
height and reach. Press down the control on
the left-hand side of the steering column. Then
adjust the steering wheel to the position that
suits you best. Press the control back into
place to lock the steering wheel. If this is difficult, press the steering wheel slightly while
pressing the control back.
WARNING
Adjust the steering wheel before driving off,
never while driving. Check that the steering
wheel is fixed in position.
68
G027005
G026999
G028425
02
Open the tailgate by pulling the handle indicated in the illustration. Fold down the rear flap
by lifting the handle up.
02 Instruments and controls
Power windows
Operating
To open a window:
Depress the front of the control.
To close a window:
Raise the front of the control.
NOTE
One way to reduce the pulsating wind noise
when the rear windows are open is to also
open the front windows slightly.
WARNING
Driver's door
If there are children in the car:
•
02
Always remember to switch off the
power supply to the power windows by
removing the remote control key if the
driver leaves the car.
•
Make sure that children or other passengers cannot be trapped in any way
when closing the windows.
If the rear door windows are operated from
the driver's door - check that none of the
rear seat passengers is in danger of getting
their hands caught when closing the windows.
G029571
The power windows are operated using the
controls in the doors. The ignition key must be
in position I or II for the power windows to
operate. The windows continue to work when
the car has stopped and the remote control key
has been removed, provided none of the doors
is opened. Operate the windows with caution.
Controls, power windows.
Front window controls
Rear window controls
The driver can operate all power windows from
the driver's seat. The windows can be opened
and closed in two ways:
• Depress one of the controls (A) or (B) gently, or pull them up gently. The power windows go up or down as long as the switch
is actuated.
• Fully depress one of the controls (A) or (B)
or raise it, then release. The side window
will then open or close automatically. If the
window is obstructed by an object, the
movement will stop.
``
69
02 Instruments and controls
Power windows
02
Rear power windows
The light in the switch is illuminated
NOTE
The function auto up for the passenger side
is only available in certain markets.
The rear door windows can only be operated
from the driver's door.
The light in the switch is extinguished
The rear door windows can be operated both
with the controls on each rear door and with
the controls on the driver's door.
Blocking power windows in the rear
doors
G029573
G029572
G029574
Front passenger seat
Blocking rear power windows and electric child
safety locks*.
The power windows in the rear seat can be
blocked with the switch on the driver's door
control panel. Always remember to switch off
current to the power windows (i.e. remove the
remote control key) if you leave children in the
car unattended.
70
The rear door windows can be operated with
the controls on the doors and the switch on the
driver's door. If the light in the switch for blocking power windows in the rear doors (located
in the driver's door control panel) is illuminated,
the rear door windows can only be operated
from the driver's door.
WARNING
The control for the power window at the front
passenger seat operates that window only.
* Option/accessory, for more information, see Introduction.
If the rear door windows are operated from
the driver's door, check that none of the rear
seat passengers are in danger of becoming
trapped in any way when they are closed.
02 Instruments and controls
Windows, rearview and door mirrors
Interior rearview mirror with compass*
Interior rearview mirror
Correct zone on compass
02
Z
O
N
E
C
A
L
Dimming
Normal position
Dimmed position.
Bright light from behind could be reflected in
the rearview mirror and dazzle the driver. Use
dimming when disturbed by light from behind.
Automatic dimming*
Bright light from behind is automatically
dimmed by the rearview mirror.
G026950
Z
O
N
E
G026965
G026660
C
A
L
The upper left-hand corner of the rearview mirror has an integrated display that shows the
compass direction in which the front of the car
is pointing. Eight different directions are shown
with English abbreviations: N (north), NE (north
east), E (east), SE (south east), S (south), SW
(south west), W (west) and NW (north west).
If the compass is activated then it starts automatically in ignition position II or when the
engine is running. Switch the compass on or
off by pressing the button set into the rear of
the mirror. Use a straightened paper clip for
example. The button is countersunk
approximately 2.5 centimetres in the mirror.
The earth is divided into 15 magnetic zones.
The compass is set for the geographical area
to which the car was delivered. The compass
should be calibrated if the car is moved across
several magnetic zones.
1. Ignition position II.
2. Press and hold the button on the rear of the
mirror for approximately 3 seconds until
ZONE is shown (use a straightened paper
clip for example). The number for the current area is shown.
3. Press the button several times until the
number for the required geographic area
(1–15) is shown. After several seconds the
``
* Option/accessory, for more information, see Introduction.
71
02 Instruments and controls
Windows, rearview and door mirrors
02
72
display returns to show the compass direction, this means that the change of zone is
complete.
02 Instruments and controls
Windows, rearview and door mirrors
G026677
02
Magnetic zones for the compass.
``
73
02 Instruments and controls
Windows, rearview and door mirrors
Calibration
02
Door mirrors
WARNING
The compass may need calibrating to work
correctly. For best results, switch off all major
power consumers such as interior lighting,
ventilation fan, heated rear window etc. and
avoid having metal objects and magnetic
objects close to the mirror.
Adjust the mirrors before you begin driving.
Door mirrors with memory function*
If the car has door mirrors with memory function, they work together with the memory setting of the seat, see page 97.
1. Stop the car in a wide open area with the
engine running.
Memory function in remote control*
3. Drive slowly in a circle at a speed of no
more than 8 km/h until CAL disappears
from the display. Which is when calibration
is complete.
4. Alternative calibration method: Drive off as
usual. CAL disappears from the display
when calibration is complete.
G029575
2. Press and hold the button on the rear of the
rearview mirror (use a paper clip or similar)
until CAL is shown again (approx. 6 seconds).
The controls for adjusting the two door mirrors
are at the front of the driver's door armrest. The
rearview mirrors can be operated in ignition
position I and II.
1. Press the L button for the left-hand door
mirror or the R button for the right-hand
door mirror. The light on the button illuminates.
2. Adjust the position with the joystick in the
centre.
3. Press the L or R button again. The light
goes out.
Folding in the door mirrors, see page 55.
74
* Option/accessory, for more information, see Introduction.
When you unlock the car with one of the remote
controls and change the setting of the door
mirrors, these new settings are saved in the
remote control. The next time you unlock the
car with the same remote control and open the
driver's door within five minutes, the mirrors
will assume their stored positions.
Laminated side windows*
The laminated windows in the front and rear
doors improve sound insulation in the passenger compartment and provide better protection against unauthorised entry.
02 Instruments and controls
Windows, rearview and door mirrors
Water and dirt-repellent coating on the
front side windows*
02
Side windows treated with the water
and dirt-repellent coating are marked
with a small symbol. For information on glass
care, see page 191.
IMPORTANT
Do not use a metal ice scraper to remove ice
from the windows. The water and dirt-repellent coating could be damaged.
* Option/accessory, for more information, see Introduction.
75
02 Instruments and controls
Power sunroof*
Open positions
Ventilation position
WARNING
To open:
If there are children in the car:
02
Switch off the supply to the power sunroof
by removing the remote control key if the
driver leaves the car.
Press the rear edge of the control (5)
upward.
To close:
Pull the rear edge of the control (6) downward.
Switch from ventilation position to comfort
position; pull the control rearwards to its end
position (4) and release.
G007503
Automatic operation
G027010
The sunroof controls are located in the roof
panel. The sunroof can be opened in two positions:
Ventilation position, up at the rear edge
Sliding position, backwards/forwards
The remote control key must be in position I or
II.
Closing, automatic
Opening, automatic
Opening, ventilation position
Closing, ventilation position
* Option/accessory, for more information, see Introduction.
In order to open from comfort position to maximum opening:
Closing, manual
Opening, manual
76
Move the control over the resistance point
position (3) to the rearmost end position (4) or
over the resistance point position (2) to the
front end position (1) and release. The sunroof
will open to the comfort position or will close
completely.
Pull the control to the rear once more to the
end position (4) and release.
Manual operation
To open:
Pull the control rearward to the point of
resistance (3). The sunroof moves toward
the fully open position as long as the button
is held depressed.
02 Instruments and controls
Power sunroof*
To close:
Press the control forward to the point of
resistance (2). The sunroof moves toward
the closed position as long as the button is
held depressed.
WARNING
The sunroof's pinch-protection function
only operates during automatic closing, not
manual.
matically when the sunroof is opened. Grip the
handle and slide the screen forward to close it.
02
Pinch protection
The sunroof's pinch protection function is activated if the hatch is blocked by an object. If
blocked, the sunroof will stop and automatically open to the previous position.
WARNING
The sunroof's pinch protection function only
operates during automatic closing, not during manual closing.
Sunscreen
G020157
Make sure that nobody is in danger of
becoming trapped in any way when closing
the sunroof.
The sunroof features a manual, sliding interior
sunscreen. The sunscreen slides back auto-
* Option/accessory, for more information, see Introduction.
77
02 Instruments and controls
HomeLinkŸ *
General
NOTE
HomeLinkŸ is designed not to work if the car
02
is locked from the outside.
Save the original remote controls for future
programming (e.g. when switching to
another car).
Delete the button programming when the
car is to be sold.
G030070
Metallic sun visors should not be used in
cars fitted with HomeLinkŸ. This may have
an adverse effect on its function.
HomeLinkŸ is a programmable remote control
which can control up to three different devices
(e.g. garage door, alarm system, outdoor lighting and indoor lighting etc.) and in doing so
replace their remote controls. HomeLinkŸ is
supplied built into the left-hand sun visor.
The HomeLinkŸ panel consists of three programmable buttons and one indicator lamp.
Operation
When HomeLinkŸ is fully programmed it can be
used in place of the separate original remote
controls.
Depress the programmed button to activate
the garage door, alarm system etc. The indicator lamp illuminates for the time that the button is kept depressed.
NOTE
If the ignition is not activated, HomeLinkŸ
will work for 30 minutes after the driver's
door has been opened.
The original remote controls can of course be
used in parallel with HomeLinkŸ.
78
* Option/accessory, for more information, see Introduction.
WARNING
If HomeLinkŸ is used to operate a garage
door or gate, ensure that nobody is in the
vicinity of the door or gate while it is in
motion.
Do not use the HomeLinkŸ remote control
for any garage door that does not have
safety stop and safety reverse. The garage
door must react immediately when it
detects that something is preventing its
movement, and stop directly and reverse. A
garage door without these characteristics
could cause personal injury. For further
information - contact the supplier via the
Internet: www.homelink.com.
Programming for the first time
The first step erases the memory in
HomeLinkŸ and must not be carried out when
only one individual button is being reprogrammed.
1. Depress the two outer buttons and do not
release until the indicator lamp starts to
flash after approx. 20 seconds. The flashing indicates that HomeLinkŸ is set in
"learn mode" and is ready to be programmed.
2. Position the original remote control
5-30 cm from HomeLinkŸ. Monitor the indicator lamp.
02 Instruments and controls
HomeLinkŸ *
The particular distance that is required
between the original remote control and
HomeLinkŸ depends on the programming
of the device in question. Perhaps several
attempts will be required at different distances. Maintain each position for approx.
15 seconds before trying a new one.
ess is repeated for approx. 20 seconds
and indicates that the device has a "rolling code". The garage door, gate or similar is not activated when the programmed HomeLinkŸ button is
depressed. Continue the programming
in accordance with the following.
3. Depress the button for the original remote
control and the button to be programmed
on HomeLinkŸ simultaneously. Do not
release the buttons until the indicator lamp
has changed over from slow to rapid flashing. The rapid flashing indicates successful
programming.
5. Locate the "programming button1" on the
receiver for the garage door for example,
normally located close to the antenna's
bracket on the receiver. If you have difficulty in finding the button - consult the
supplier's manual, or contact the supplier
via the Internet: www.homelink.com.
4. Test the programming by depressing the
programmed button on HomeLinkŸ and
watching the indicator lamp:
6. Depress and release the "programming
button". The button flashes for
approx. 30 seconds and the next step must
be carried out within this period.
• Constant glow: The indicator lamp illuminates with a constant glow when the
button is kept depressed, this indicates
that the programming is complete. The
garage door, gate or similar should now
be activated when the programmed
HomeLinkŸ button is depressed.
• Glow not constant: The indicator lamp
flashes quickly for approx. 2 seconds
and then changes over to a constant
glow for approx. 3 seconds. This proc-
1
7. Depress the programmed button on
HomeLinkŸ, while the "programming button" is still flashing, keep it depressed for
approx. 3 seconds and then release.
Repeat the press/hold/release sequence
up to 3 times to conclude the programming.
Programming individual buttons
To reprogram an individual button, proceed in
accordance with the following:
02
1. Depress the required button on
HomeLinkŸ and do not release until step 3
has been completed.
2. When the indicator lamp on HomeLinkŸ
starts to flash, after approx. 20 seconds,
position the original remote control
5-30 cm from HomeLinkŸ. Monitor the indicator lamp.
The particular distance that is required
between the original remote control and
HomeLink depends on the programming of
the device in question. Perhaps several
attempts will be required at different distances. Maintain each position for approx.
15 seconds before trying a new one.
3. Depress the button on the original remote
control. The indicator lamp will start to
flash. When the flashing has changed over
from a slow to a rapid flashing - release
both buttons. The rapid flashing indicates
successful programming.
4. Test the programming by depressing the
programmed button on HomeLink and
watching the indicator lamp:
Button designation and colour vary depending on manufacturer.
``
* Option/accessory, for more information, see Introduction.
79
02 Instruments and controls
HomeLinkŸ *
• Constant glow: The indicator lamp illuminates with a constant glow when the
button is kept depressed, this indicates
that the programming is complete. The
garage door, gate or similar should now
be activated when the programmed
HomeLinkŸ button is depressed.
02
• Glow not constant: The indicator lamp
flashes quickly for approx. 2 seconds
and then changes over to a constant
glow for approx. 3 seconds. This process is repeated for approx. 20 seconds
and indicates that the device has a "rolling code". The garage door, gate or similar is not activated when the programmed HomeLinkŸ button is
depressed. Continue the programming
in accordance with the following.
7. Depress the programmed button on
HomeLinkŸ, while the "programming button" is still flashing, keep it depressed for
approx. 3 seconds and then release.
Repeat the press/hold/release sequence
up to 3 times to conclude the programming.
Erasing programming
It is only possible to erase the programming for
all the buttons on HomeLinkŸ, not for individual
buttons.
5. Locate the "programming button2" on the
receiver for the garage door for example,
normally located close to the antenna's
bracket on the receiver. If you have difficulty in finding the button - consult the
supplier's manual, or contact the supplier
via the Internet: www.homelink.com.
6. Depress and release the "programming
button". The button flashes for approx. 30
seconds and the next step must be carried
out within this period.
2
80
Button designation and colour vary depending on manufacturer.
* Option/accessory, for more information, see Introduction.
Depress the two outer buttons and do not
release until the indicator lamp starts to
flash after approx. 20 seconds.
> HomeLinkŸ is now set in so-called
"learn mode" and is ready to be programmed once more, see page 78.
02 Instruments and controls
02
81
General information on climate control................................................... 84
Electronic Climate Control, ECC............................................................. 88
Fuel-driven parking heater* .................................................................... 91
82
* Option/accessory, for more information, see Introduction.
CLIMATE CONTROL
03 Climate control
General information on climate control
03
Air conditioning
Ice and snow
The climate control system cools or heats as
well as dehumidifies the air in the passenger
compartment. The car is equipped with electronic climate control (ECC).
Remove ice and snow from the climate control
system air intake (the grille between the bonnet
and the windscreen).
NOTE
The air conditioning can be switched off, but
to ensure the best possible air in the passenger compartment and prevent the windows from misting, it should always be on.
Misting windows
Reduce the problem of windows misting up on
the inside by cleaning the windows. Use a regular window cleaner.
Multi-filter
Make sure that the multi-filter/pollen filter is
replaced regularly. Volvo recommends you
consult an authorised Volvo workshop.
Fault tracing and repair
Volvo recommends that you engage an authorised Volvo workshop for the fault tracing and
repair of the climate control system.
Refrigerant
The climate control system contains R134a
refrigerant. This refrigerant contains no chlorine, which means that it is harmless to the
ozone layer. The system must only be charged
with R134a refrigerant, see also page 279.
Volvo recommends that you engage an authorised Volvo workshop to carry out this work.
Actual temperature
The temperature you select corresponds to the
physical experience with reference to factors
such as air speed, humidity and solar radiation
in and around the car.
Sensor location
• The sun sensor is on the top side of the
dashboard.
• The temperature sensor for the passenger
compartment is behind the climate control
panel.
NOTE
Do not cover or block the sensors with
clothing or other objects.
Side windows and sunroof
Ventilation fan function
When the engine is off (and if the remote control key is in position I or II), the ventilation fan
is automatically switched off. This is to prevent
the battery from becoming discharged.
To activate the ventilation fan, turn the fan control and set the desired speed.
84
ECC (electronic climate control)
To ensure that the air conditioning works satisfactorily, the side windows, and sunroof if
appropriate, should be closed.
Acceleration
The air conditioning system switches off temporarily at full throttle. You may briefly feel a
temporary rise in temperature.
03 Climate control
General information on climate control
Condensation
Air distribution
Air vents in the dashboard
In warm weather, condensation from the air
conditioning may drip under the car. This is
normal.
To ventilate the climate system's control system the ventilation fan can be started up to 50
minutes after the car's ignition has been
switched off. The fan is then switched off automatically after approx. 15 minutes.
03
G028577
With ECC, the air conditioning system is controlled automatically and is used just enough to
cool the passenger compartment and to adequately dehumidify the incoming air. This provides better fuel economy compared to conventional systems where the air conditioning
cools the air to just above freezing point.
G027043
Fuel economy
Incoming air is distributed through several different vents located throughout the car.
Open
Closed
Lateral airflow
Vertical airflow.
1. Aim the outer vents towards the side windows to remove misting from the front side
windows.
2. In cold climates: close the centre vents for
the most comfortable climate and best
demisting.
``
85
03 Climate control
General information on climate control
Panel vents in the door pillar
Ventilated front seats (Executive)
To obtain maximum ventilation:
Hold
depressed for about 2 seconds.
To decrease the ventilation in steps:
Press briefly on
.
To switch off the ventilation:
03
Hold
depressed for about 2 seconds.
Open
Closed
Lateral airflow
Vertical airflow.
1. Aim the outer vents toward the rear side
windows to remove misting.
2. Aim the vents inwards for a comfortable
climate in the rear seat.
Bear in mind that small children can be sensitive to airflow and draughts.
G030244
0
G027064
The ventilation can be used at the same time
as front seat heating. For example, the function
can be used to remove moisture from clothes.
Control for front seat ventilation.
The ventilation system consists of fans in the
seat and backrest that draw air through the
seat upholstery. The cooling effect increases
the cooler the passenger compartment air
becomes.
The ventilation is regulated from a control on
the control panel on the side of the front seats
which has three steps for the fan speed.
To start seat ventilation:
Press briefly on
.
To increase the ventilation in steps:
86
Press briefly on
.
The ventilation system can be activated when
the engine is running.
NOTE
The seat ventilation should be used carefully
by people sensitive to draughts. Comfort
level I is recommended for long-term use.
IMPORTANT
The seat ventilation cannot be started when
passenger compartment temperature is
below 5 °C. This is to avoid chilling anyone
sitting in the seat.
03 Climate control
General information on climate control
Seat heating, outer rear seats
(Executive)
G030976
03
Button for rear seat heating, On/Off.
The seat heating in the rear seats is controlled
with a button control in accordance with the
illustration above. There is one control on each
side of the rear centre console for each respective rear seat.
To start seat heating:
Press the button.
> The symbol in the button illuminates.
To stop the heating:
Press the button.
> The lamp goes out.
87
03 Climate control
Electronic Climate Control, ECC
Control panel
03
AC – On/off (ON/OFF)
Temperature, right-hand side
Recirculation/Multifilter with sensor*
Temperature, left-hand side
Recirculation
Fan
AUTO
Fan, rear passenger compartment*
Air distribution
Functions
Passenger compartment temperature sensor
1. AC – ON/OFF
Defroster, windscreen and side windows
Rear window and door mirror defrosters
Heated front seats
88
ON: The air conditioning is on. It is controlled
by the system's AUTO function. This way,
incoming air is cooled and dehumidified.
OFF: When the defroster function is activated
the air conditioning is switched on automatically (can be switched off using the AC button).
* Option/accessory, for more information, see Introduction.
2. Air quality system, recirculation/
multifilter*
Certain cars are equipped with a "Multifilter"
and air quality sensor. The Multifilter separates
gases and particles, thus reducing the volume
of odours and pollutants. The air quality sensor
detects increased levels of contaminants in the
outside air. When the air quality sensor detects
contaminated outside air, the air intake is
closed and the air in the passenger compartment is recirculated. The Multifilter also cleans
the air recirculating in the passenger compartment.
03 Climate control
Electronic Climate Control, ECC
A green light (AUT) illuminates
in the button when the air quality sensor is active.
• If misting occurs, you can use the defroster
functions for the windscreen, side windows and rear window.
• Follow the Volvo service programme for
Operation:
Press AUTO to activate the air quality sensor (normal setting).
Or:
Select one of the following three functions
:
by repeatedly pressing
• The lamp for MAN illuminates. Recirculation is now activated.
• No lamp illuminates. Recirculation is not
activated unless needed to cool in a
warm climate.
• The lamp for AUT illuminates. Recirculation is now activated.
Keep the following in mind:
• Make it a rule to have the air quality sensor
activated at all times.
• Recirculation is limited in cold weather to
avoid misting.
• If misting occurs, you should deactivate
the air quality sensor.
the recommended replacement interval of
the Multifilter. If the car is used in environments where more contaminants are present, it may be necessary to change the
Multifilter more often.
3. Recirculation
Recirculation can be used to shut out bad air,
exhaust, etc. from the passenger compartment. The air in the passenger compartment is
recirculated, i.e. no outside air is taken into the
car when this function is activated.
If you allow the air in the car to recirculate, there
is a risk of icing and misting, especially in winter.
The timer function (cars with Multifilter and air
quality sensor have no timer function) minimises the risk for ice, misting and bad air.
Activate the function as follows:
1. Press
for more than 3 seconds. The
lamp flashes for 5 seconds. The air recirculates in the car for 3-12 minutes depending on the outside temperature.
2. The timer function is activated each time
you press
.
To switch off the timer function:
Press
again for more than 3 seconds. The lamp illuminates for 5 seconds
to confirm your selection.
4. AUTO
The AUTO function automatically regulates climate control and maintains the selected temperature. The automatic function controls
heating, air conditioning, air quality sensor, fan
speed, recirculation and air distribution. If you
select one or more manual functions, the other
functions continue to be controlled automatically. All manual settings are switched off when
AUTO is switched on.
03
5. Air distribution
• When the top button is depressed, air is
directed to the windows
• When the centre button is depressed, air is
directed to the head and body
• When the lower button is depressed, air is
directed to the legs and feet
Press AUTO to return to automatic air distribution.
6. Passenger compartment temperature
sensor
The passenger compartment temperature sensor monitors the temperature inside the car.
``
89
03 Climate control
Electronic Climate Control, ECC
03
7. Defroster, windscreen and side
windows
2. Press once more: Low heat – one lamp illuminates.
13. Fan, rear passenger compartment
(option in cars seating seven)
Used to quickly remove misting and ice from
the windscreen and side windows. Air flows to
the windows at high fan speed. The light in the
defroster button illuminates when the function
is active.
3. Press once more: Heating switched off –
no lamps illuminate.
When the function is selected the following
also takes place to provide maximum dehumidification of the air in the passenger compartment:
10 and 11. Temperature selector
Fan speed can be increased or decreased by
turning the knob. This only applies if AC is
selected for both front and rear* passenger
compartment. The button for rear passenger
compartment is in the centre console switch
panel, see page 55.
Volvo recommends that an authorised Volvo
workshop adjusts the temperature.
The two knobs can be used to set the temperature for the passenger and driver's sides
of the car.
• the air conditioning (AC) is automatically
engaged (can be switched off with the AC
button).
• recirculation is automatically disengaged.
When the defroster function
is switched
off the climate control system returns to the
previous settings.
8. Rear window and door mirror
defrosters
Use this button to quickly remove misting and
ice from the rear window and door mirrors, see
page 57 for further information about this function.
9. Heated front seats
To activate front seat heating:
NOTE
Heating or cooling cannot be hastened by
selecting a higher or lower temperature than
the actual desired temperature.
12. Fan
Turn the knob to increase or decrease fan
speed. If AUTO is selected then fan speed is
regulated automatically. The previously set fan
speed is disengaged.
NOTE
If the knob is turned anticlockwise and the
fan indicator in the display goes out, the fan
and the air conditioning are switched off.
1. Press once: High heat – both lamps illuminate.
90
* Option/accessory, for more information, see Introduction.
03 Climate control
Fuel-driven parking heater*
G027095
General information about heaters
TIMER 1 and TIMER 2. Here, time refers to the
time when the car is heated and ready. The
car's electronic system calculates when heating should be started based on the outside
temperature.
The car must be outdoors when the parking
heater is used.
The heater is not run if the outside temperature
exceeds 25 °C. At -10 °C and below, the maximum running time of the parking heater is 60
minutes.
Check in the display that the parking heater
is off. (When the parking heater is running,
PARK HEAT ON is shown in the display.)
If the parking heater does not start, despite
repeated attempts, Volvo recommends that
you contact an authorised Volvo workshop. A
message is shown in the display.
READ button
RESET button
The electrical system must be "awakened"
before the parking heater can be programmed.
03
Messages in the display
Once the settings for TIMER 1, TIMER 2 and
Direct Start is activated are activated, the
amber warning symbol in the combined instrument panel illuminates and explanatory text is
shown in the display.
Parking on a hill
This is done by:
If you park your car on a steep incline, the front
of the car should be facing down the slope to
ensure the supply of fuel to the parking heater.
• pressing the READ button or
• activating main beam or
• turn the remote control key to key position
I.
Switch off the parking heater before refuelling. Fuel which spills out could be ignited.
When you leave the car, you will receive a message regarding the current settings of the system. The message disappears when the car is
locked from the outside using the remote control key.
Thumbwheel
The parking heater can be started immediately
or set with two different start times using
WARNING
Warning decal on fuel filler flap.
``
* Option/accessory, for more information, see Introduction.
91
03 Climate control
Fuel-driven parking heater*
Clock/timer
If the car clock is reset after the heater timers
are programmed, the selected times will be
cancelled.
03
Setting the TIMER
For safety reasons, you can only programme
times for the following 24 hours, not several
days in advance.
1. Scroll using the thumbwheel until TIMER
1 or 2 is shown in the display.
2. Briefly press RESET so that the hours setting starts to flash.
3. Scroll with the thumbwheel to the desired
hour.
2. Use the thumbwheel to scroll to the text
PARK HEAT TIMER 1 or 2. The text ON
flashes on the display.
3. Press RESET. The text OFF is shown with
a constant glow and the parking heater is
switched OFF.
Direct start
1. Scroll with the thumbwheel until DIRECT
START is shown in the display.
2. Press RESET to access the options ON or
OFF.
3. Select ON.
4. Briefly press RESET to move to the flashing minutes setting.
The heater will now run for 60 minutes. Heating
of the passenger compartment will begin as
soon as the engine coolant has reached a temperature of 30 °C.
5. Scroll with the thumbwheel to the desired
minute.
Immediate stop of heater
6. Briefly press RESET to confirm the setting.
1. Scroll with the thumbwheel until DIRECT
START is shown in the display.
7. Press RESET to activate the timer.
Deactivating timer-started parking
heater
Proceed as follows to manually switch off the
parking heater before the set time has elapsed:
2. Press RESET to access options ON or
OFF.
3. Select OFF.
1. Press READ.
92
* Option/accessory, for more information, see Introduction.
NOTE
The car can be started and driven while the
parking heater is still running.
Battery and fuel
If the battery has insufficient charge or the fuel
level is too low, the parking heater will be
switched off automatically. A message is
shown in the display. Acknowledge the message by pressing READ once.
IMPORTANT
Repeated use of the parking heater combined with short journeys may discharge the
battery and impair starting. If the heater is
used regularly, the car must be driven for the
same time as the heater is used in order to
ensure that the alternator has time to charge
the battery.
Additional heater (diesel)*
Extra heat from the additional heater may be
required in cold weather to reach the correct
temperature in the passenger compartment.
The additional heater starts automatically
when extra heat is required if the engine is running. It is switched off automatically when the
correct temperature is reached or when the
engine is switched off.
03 Climate control
03
93
Front seats.............................................................................................. 96
Front seats - Executive .......................................................................... 99
Interior lighting...................................................................................... 100
Storage spaces in the passenger compartment................................... 102
Storage spaces in the passenger compartment - Executive ............... 107
Rear seat............................................................................................... 108
Loading ................................................................................................ 110
Cargo area............................................................................................ 111
94
INTERIOR
04 Interior
Front seats
Lumbar support1, turn the wheel.
Seating position
The passenger seat backrest can be folded
forward to make room for long loads.
Backrest rake: turn the wheel.
1. Move the seat as far back as possible.
Control panel for power seat*.
2. Adjust the backrest to an upright position
90 degrees.
WARNING
3. Lift the catches on the rear of the backrest
while folding it forwards.
Adjust the position of the driver's seat
before setting off, never while driving.
4. Slide the seat forward so that the head
restraint is "locked in place" under the glovebox.
Check that the seat is locked in position.
G027960
04
Tipping the front seat backrest
Raising takes place in reverse order.
WARNING
Grasp the backrest and make sure that it is
properly locked after being folded up in
order to avoid personal injury in the event of
sudden braking or an accident.
The driver's and passenger seats can be
adjusted to the optimum sitting and driving
positions.
Raise/lower the front of the seat cushion,
pump up/down, (driver's and passenger
side*).
Raise/lower the seat, pump up/down,
(driver's and passenger side*).
1
96
Also applies to power seat.
G014805
Forward/backward: lift the handle to adjust
the distance to the steering wheel and pedals. Check that the seat is locked after
changing position.
04 Interior
Front seats
Floor mats*
Volvo supplies floor mats especially produced
for your car.
WARNING
The floor mat at the driver's seat must be
firmly fitted and secured in the attachment
clips to prevent it from being trapped
around and under the pedals.
Power seat*
ignition switch. The seat can always be
adjusted in ignition position I or II.
Store setting
1. Adjust seat.
Front edge of seat cushion up/down
2. Press and hold button MEM while pressing
button 1, 2 or 3 simultaneously.
Seat forward/rearward
Using a stored setting
Seat up/down
Backrest rake
An overload protection is deployed if one of the
seats is blocked. If this happens, turn off the
ignition and wait a short time before adjusting
the seat again. Only one of the seat's settings
can be adjusted at a time.
Memory function*
Press one of the memory buttons 1–3 until the
seat stops. If you release the button then the
movement of the seat will stop.
Key memory in remote control key
The driver's seat positions are stored in the key
memory when the car has been locked with the
remote control key. When the car is unlocked
with the same remote control key the driver's
seat and rearview mirrors adopt the stored
positions when the driver's door is opened.
04
NOTE
The key memory is independent of the seat
memory.
Emergency stop
If the seat accidentally begins to move, press
any of the buttons to stop the function.
The seats can be adjusted for a certain time
after unlocking the door with the remote control key without the key being inserted into the
Buttons for memory function.
``
* Option/accessory, for more information, see Introduction.
97
04 Interior
Front seats
WARNING
Risk of crushing. Make sure that children do
not play with the controls.
Check that there are no objects in front of,
behind or under the seat during adjustment.
Ensure that none of the backseat passengers will be trapped.
04
98
04 Interior
Front seats - Executive
Comfort seats, front
Massage
Setting lumbar
Massage
Button for activating massage.
Hard massage
Lumbar
Soft massage
Each front seat has massage in the backrest.
The massage is performed by air cushions that
can massage with either a hard or soft setting.
When one of the settings is selected the massage is carried out in accordance with the
cycle: massage 6 minutes - pause 4 minutes massage 6 minutes etc.
When the button is in the centre position, or
when the remote control key is in position 0,
massage is not activated.
G030229
G030180
G030183
04
Button for setting lumbar.
The lumbar support is set with the same air
cushions used for massage. Adjustment can
be made steplessly both in terms of depth and
height using the control button, see the illustration above.
The lumbar support can be set when massage
is not active.
A memory function recalls the lumbar support's setting when massage is stopped or
when the pressure in the air cushions has
decreased, e.g. after a longer period of parking.
99
04 Interior
Interior lighting
Reading lamps and interior lighting
well as when the engine is running. The lighting
can also be activated within 10 minutes after:
Rear roof lighting
• the engine has been switched off and the
ignition is in position 0
• the car has been unlocked but the engine
has not been started
Following which, it is switched off automatically.
Front roof lighting
Controls in roof console for front reading lamps
and passenger compartment lighting.
Reading lamp left-hand front
Interior lighting
Reading lamp right-hand front
Passenger compartment lighting1 is switched
on with a short press on button (2), at the same
time automatic lighting is activated, see
page 101. Passenger compartment lighting is
switched off with a short press on button (2).
All lighting in the passenger compartment can
be switched on in ignition position I and II as
1
100
Courtesy lighting follows passenger compartment lighting.
The front reading lamps are switched on or off
by pressing the relevant button in the roof console.
G027153
G026960
04
Rear reading lamps
Reading lamp left-hand rear, On/Off
Reading lamp right-hand rear, On/Off
The lamps are switched on or off by pressing
the relevant button.
There are also reading lamps for the third row
of seats in cars that seat seven.
Courtesy lighting
Courtesy lighting (and passenger compartment lighting) is switched on and off respectively when a side door is opened or closed.
04 Interior
Interior lighting
Cargo area lighting
The cargo area has a lamp on the inside of the
tailgate.
The rear lamp in the passenger compartment
and the lamp in the tailgate are switched on
and off respectively when the tailgate is
opened or closed.
Glovebox lighting
The light illuminates automatically when the
cover is lifted.
The programmed times, 30 seconds and
10 minutes, can be changed by a Volvo workshop.
Automatic lighting
Automatic lighting can be disengaged by
pressing button (2), see page 100, and holding
it depressed for more than 3 seconds. A short
press on the button re-engages automatic
lighting.
Glovebox lighting is switched on and off
respectively when the lid is opened or closed.
When automatic lighting is activated the passenger compartment lighting is switched on
automatically2 and remains on for 30 seconds:
Vanity mirror*
• the car is unlocked with the key or remote
04
control key
• the engine is switched off and the key is
turned to the 0 position.
Passenger compartment lighting is switched
on and remains on for 10 minutes if one of the
doors is open and the passenger compartment
lighting is not switched off.
G027045
Passenger compartment lighting is switched
off when:
2
• the engine is started
• the car is locked with the key or remote
control key.
The function is light-dependent and is only activated when it is dark.
* Option/accessory, for more information, see Introduction.
101
04 Interior
Storage spaces in the passenger compartment
Storage spaces
04
ATTENTION
Pakjdskdl ioiuip kjöpp opoodidåuswi
AIRBAG
MY KEY
L E CTOR
SE
SOUND
ENTER
EXIT
MENU
80
G027041
8504251r
102
04 Interior
Storage spaces in the passenger compartment
Storage compartment in third row of seats
Pen holder
Glovebox
Storage compartment and cup holder
Ticket clip
Glovebox
Storage tray in centre console
Cup holder for rear seat passengers
ATTENTION
Pakjdskdl ioiuip kjöpp opoodidåuswi
Storage pocket (also on the front edge of
the front seat cushions)
AIRBAG
MY KEY
L E CTOR
SE
SOUND
ENTER
04
EXIT
MENU
WARNING
Ensure that no hard, sharp or heavy objects
lie or protrude in such a way that they could
cause injury during heavy braking.
The centre console contains a pen holder.
80
G027025
G027030
Bag holder
The glovebox can be used to store things such
as the owner's manual, maps, pens and petrol
cards.
Always secure large and heavy objects with
a seatbelt or cargo retaining straps.
``
103
04 Interior
Storage spaces in the passenger compartment
Coat hanger
Ashtray for rear seat passengers*
Cup holder/bottle holder for rear seat
passengers
The coat hanger is only intended for light garments.
Open the ashtray by pulling the top edge outward.
Pull the bottom edge of the insert to open.
To empty:
The cup holder insert can be removed:
1. Open the ashtray.
2. Press the cover outwards and tip it back.
3. Then lift it out.
104
G027063
G027018
G027028
04
* Option/accessory, for more information, see Introduction.
Detach the two clips so the holder can be
used for large bottles.
04 Interior
Storage spaces in the passenger compartment
Storage compartment and cup holder
(cars seating seven)
Storage tray in centre console
Cup holder
This storage compartment can be used for
CDs, books and the like.
The centre console contains a storage tray for
food and drinks, for example. The armrest can
be folded back to make a "table" for rear seat
passengers.
G027020
G027019
G027040
04
Cup holder for front seat passengers.
Ashtray*
Pull out the insert to empty the astray.
Under the storage tray is a storage compartment, e.g. for CD discs.
``
* Option/accessory, for more information, see Introduction.
105
04 Interior
Storage spaces in the passenger compartment
Storage compartment in the third row
of seats (cars seating seven)
G027026
04
This storage compartment can be used for
pens and other small items.
106
04 Interior
Storage spaces in the passenger compartment - Executive
Cooler box
G027068
04
There is a cooler box under front seat's folding
armrest. Adjust the cooling level with the button (see illustration). The cooler box works
when the engine is running or in key position
II.
WARNING
Store bottles well sealed in the cooler box
and make sure that the door is closed for the
journey.
107
04 Interior
Rear seat
Rear seats – second row (cars seating
seven)
Sliding seat (cars seating seven)
Removing the rear section of the
centre console
Lowering the backrest for entry into the
car
Lift the handle (1) up while pushing the seat
forward. Do the reverse to return the seat to its
original position.
Adjusting the seat front - rear
Lift the bracket (2) to move the seat forwards
or backwards.
108
The centre seat in the second row can be slid
farther forward than the other seats. Sliding the
seat completely forward improves contact
between a child sitting on the integrated
booster cushion and front seat occupants.
Lift the bracket (A) to move the seat forwards
or backwards.
G028445
G027033
G027027
04
The centre console must first be removed if you
wish to slide the centre seat in the second row
forward.
1. Remove the rear section of the centre console by pulling the catch straight out as
illustrated above.
2. Then lift the console out of the way.
04 Interior
Rear seat
Head restraint, rear seat – centre seat
WARNING
The lowest position should only be used
when the backrest is to be folded down or
when no one is sitting in this seat.
After raising the backrests in the second
and third row, it is important to make sure
that the backrests have locked into position.
Otherwise the protective system of the
seats may be compromised.
G027015
NOTE
04
The head restraint cannot be removed completely.
The centre seat head restraint can be adjusted
to four different heights. Raise the head
restraint as necessary.
Press in the release button to lower it. See
illustration.
109
04 Interior
Loading
General
Payload depends on the car's kerb weight. The
total of the weight of the passengers and all
accessories reduces the car's payload by a
corresponding weight. For more detailed information on weights, see page 274.
WARNING
04
The car's driving characteristics change
depending on how heavily it is loaded and
how the load is distributed.
Load on the roof
Load carriers
Load carriers designed by Volvo are recommended in order to avoid damaging the car and
for maximum possible safety while driving.
Carefully follow the mounting instructions
enclosed with the load carriers.
• Check periodically that the load carriers
and load are properly secured. Lash the
load securely with retaining straps.
• Distribute the load evenly over the load
carriers. Put the heaviest objects at the
bottom.
• The size of the area exposed to the wind,
and therefore fuel consumption, increase
with the load's size.
110
• Drive gently. Avoid quick acceleration,
heavy braking and hard cornering.
WARNING
Load no more than 100 kg on the roof, inclusive of the load carriers or space box. The
car's centre of gravity and driving characteristics are altered by roof loads.
04 Interior
Cargo area
Extending the cargo area – second row
of seats
3. Release the catch (1) and fold down the
backrest. Press down to lock the backrest
in its folded position.
IMPORTANT
There must be no objects on the rear seat
when the backrest is to be folded down. The
seat belts must not be connected either.
Otherwise there is a risk of damaging the
rear seat upholstery.
WARNING
For reasons of safety, no passengers should
sit in the third row of seats if the outer head
restraints in the second row are lowered.
Extending the cargo area – third row of
seats (cars seating seven)
G027016
04
IMPORTANT
G027022
There must be no objects on the rear seat
when the backrest is to be folded down. The
seat belts must not be connected either.
Otherwise there is a risk of damaging the
rear seat upholstery.
1. Set the seats in their rearmost positions
(applies only to cars seating seven).
2. Lower the head restraint.
Push the second row of seats to its front position, see page 96.
Lift the handle upward.
Slide the seat cushion to its rearmost position. Fold in the right and left-hand cargo
eyes in order to avoid damage when lowering the backrest.
Fold down the backrest (The head restraint
folds in automatically when the backrest is
folded).
Repositioning the third row of seats
1. Raise the backrest to its normal position.
2. Take hold of the eyes and pull out the seat
cushion until you hear a click.
``
111
04 Interior
Cargo area
mind that improperly secured or incorrectly
loaded objects in the cargo area could be
thrown forward with great speed and force in
the event of a collision or sudden braking,
causing serious injuries.
3. Raise the head restraint.
> The seat is now ready for use.
General
Bear in mind that if an object weighing 20 kg is
subjected to a frontal collision at a speed of
50 km/h, its impact weight will be 1000 kg.
Think about the following when loading:
• Do not load extremely heavy objects up by
04
G027031
the front seats. The lowered backrest will
be pressed down unnecessarily hard.
Payload depends on the car's kerb weight. The
total of the weight of the passengers and all
accessories reduces the car's payload by a
corresponding weight. For more detailed information on weights, see page 274.
Loading the cargo area
The seatbelts and airbags provide the driver
and passengers substantial protection, especially in frontal collisions. However, you must
also remember to protect yourself against injuries from behind. When loading cargo, bear in
112
• Place the load by the backrest.
• Position heavy loads as low as possible.
• Position wide loads on each side of the
division in the backrest.
• Cover sharp edges with something soft.
• Secure the load with retaining straps using
the car's lashing eyes.
• Never load above the backrest without a
load net.
WARNING
The driving characteristics of the car change
based on the car's kerb weight and how
heavily it is loaded.
WARNING
Never load cargo above the backrests! If
you do so, the load could be thrown forward
in the event of sudden braking or a collision
and severely injure you or your passengers.
Remember to always secure (bind) the load
properly.
If the rear seat backrest is lowered, do not
load the car higher than 50 mm under the
top edge of the rear passenger windows.
Leave 10 cm of free space from the windows inwards. Otherwise, the intended protection of the inflatable curtain, which is hidden in the headlining, may be compromised.
Always secure the load. Always secure the
load. During heavy braking the load may
otherwise shift, causing personal injury to
the car's occupants.
Turn off the engine and apply the parking
brake when loading or unloading long
objects! Otherwise you may accidentally
knock the gear lever or gear selector with
the load and cause a gear to engage and the
car to move off.
04 Interior
Cargo area
Safety net
Fitting the safety net
Only applies to cars seating seven:
1. Make sure the net lies in front of the side
panel armrest when securing.
2. Tension the safety net using the anchoring
straps.
Folding up the safety net
G027058
04
The safety net prevents luggage and cargo
from being thrown forward in the passenger
compartment during heavy braking.
The net is made of a strong nylon fabric and
can be secured two different ways:
• Behind the rear seat backrest
• Behind the front seats if the rear seat is
lowered.
If the car is equipped with a cargo area cover,
remove it before fitting the safety net.
1. Hook the upper rod in the front or rear roof
mounting.
2. Hook the other end of the rod in the roof
mounting on the other side.
3. Secure the safety net anchoring straps in
the eyes on the floor if the net is secured in
the rear roof mountings.
4. Use the eyes in the seat slide rail if the net
is secured in the front roof mountings.
The safety net can be folded up and placed in
the cargo area floor (for cars seating five).
Press the buttons (1) in the safety net
hinges to release the hinges and fold up the
net.
``
113
04 Interior
Cargo area
Fit the protective grille as follows:
WARNING
Make sure that the upper mountings of the
safety net are correctly fitted and that the
anchoring straps are securely fastened.
Do not use a damaged net.
1. Lift in the protective grille through the tailgate opening or one of the rear doorways
(fold down the seats in the second row if
necessary).
2. Insert one of the protective grille mountings
in its bracket above the rear door behind
the second row of seats.
Steel safety grille*
5. Insert the attaching brace through the
lower mounting in the protective grille from
underneath, as indicated in the illustration.
6. Fit the spring on the attaching brace and
screw in the knob.
7. Fit the hook from the attaching brace in the
load securing eyelet and tighten the knob
until the attaching brace takes hold in the
load securing eyelet.
8. Do the same on the other side.
04
9. Tighten both attaching braces alternately.
10. Fit protective caps on the exposed screw
threads above the knobs.
The protective grille in the cargo area prevents
cargo or pets from being thrown forward in the
passenger compartment in the event of heavy
braking.
For reasons of safety, the protective grille must
always be mounted and secured correctly.
114
G027057
G027056
WARNING
3. Slide the protective grille mounting to the
front position of the bracket.
4. Place the other protective grille mounting
in its bracket above the other rear door and
slide it to the front position.
* Option/accessory, for more information, see Introduction.
For cars seating seven: For reasons of
safety, no passengers should sit in the third
row of seats if the protective grille is positioned behind the second row of seats.
04 Interior
Cargo area
Cargo cover*
Electrical socket in cargo area
Bag holder*
Slide down the cover when you wish to use the
socket. It works regardless of whether the ignition is on or off.
Pull out the cargo area cover, pull it over the
cargo and hook it into the holes in the rear pillars of the cargo area.
If the ignition is switched off and a power consumer that uses more than 0.1 A is connected
to the electric socket, a warning message is
shown in the display.
Removing the cargo area cover
G027066
G027055
G027099
04
Open the hatch in the cargo area. Hang or
secure your grocery bags using the tensioning
straps or holders.
Press the end pieces of the cargo area cover
inwards, pull up and release. When fitting,
press the end pieces of the cargo area cover
down into the holders.
NOTE
Remember not to use the electrical socket
with the engine switched off because of the
risk of discharging the car's battery.
WARNING
Do not place objects on the cargo area
cover. They could injure passengers during
braking or evasive manoeuvres.
``
* Option/accessory, for more information, see Introduction.
115
04 Interior
Cargo area
Cargo area compartment, contents
NOTE
Some components of the first-aid kit have
an expiration date and should be replaced
before this date.
Opening the compartment in the cargo
area floor (cars seating five)
Lift up the cover in the cargo area floor.
If the car is equipped with a carrier bag holder:
04
G027067
Location of first aid kit in cars seating five.
Location of first aid kit in cars seating
seven.
The following is housed in the floor compartment:
•
•
•
•
116
Warning triangle*
Tool kit
First aid kit*
Jack (alternative location)
Lift the cover, detach the tensioning straps
to the grocery bag holder.
Opening the compartment in the cargo
area floor (cars seating seven)
Lift up the cover.
If the car is equipped with a carrier bag holder:
Open the upper cover, detach the tensioning straps to the grocery bag holder, if fitted, and open the lower cover.
IMPORTANT
Remember not to put anything in the area
that the cushions fold into. The cushions
and seat mechanisms could be damaged.
04 Interior
04
117
Remote control key - key with remote control......................................
Locking and unlocking..........................................................................
Child safety locks..................................................................................
Alarm*....................................................................................................
118
* Option/accessory, for more information, see Introduction.
120
122
125
127
LOCKS AND ALARM
05 Locks and alarm
Remote control key - key with remote control
Keys – Electronic immobiliser
The key blade's unique code is provided by
authorised Volvo workshops, which are recommended when ordering new key blades.
Remote control functions
A maximum of six remote control keys can be
programmed and used for one single car.
Immobiliser
05
Remote control key. This key opens all locks.
The car is supplied with two remote control
keys - they are collapsible and equipped with
built on remote control.
Loss of key
If you should lose one of your remote control
keys, you are recommended to bring the
remaining keys to an authorised Volvo workshop. The code of the missing key must be
erased from the system as a theft prevention
measure. The other keys must be re-coded in
the system at the same time.
NOTE
The key blade on the remote control key
must be fully extended (as illustrated) when
starting the car. Otherwise there is a risk that
the immobiliser function will prevent the car
from starting.
Ignition keys and electronic immobiliser
The remote control key must not hang with
other keys or metal objects on the same key
ring. The electronic immobiliser could be activated erroneously and the car will not start.
G027013
G030177
The keys are fitted with coded chips. The code
must be accepted by the reader (receiver) in
the ignition switch. The car can only be started
if the correct key with the correct code is used.
Unlocking
Press the button once to unlock all doors,
the tailgate and the fuel filler flap simultaneously.
Tailgate
• Press the button once to unlock the tailgate only.
• Two presses both unlocks and opens the
tailgate slightly.
Panic function
Panic function - Can be used to attract attention in an emergency. Press and hold the red
button for at least 3 seconds or press it 2 times
120
05 Locks and alarm
Remote control key - key with remote control
within the same space of time to activate the
direction indicators and the horn. The panic
alarm is deactivated automatically after 25 seconds or by pressing any of the buttons on the
remote control key.
The folding key will open automatically with
one press of the button.
3. Refit the cover. Make sure the rubber seal
is properly fitted and free from damage to
prevent water from entering.
Replacing the remote control key's
battery
4. Return the old battery to your Volvo workshop so that it is disposed of in an environmentally safe manner.
Approach light duration
Do the following when you approach the car:
Press the yellow button on the remote control key.
The interior lighting, position/parking lamps,
number plate lighting, door mirror lamps* will
now switch on. The lighting on a coupled trailer
will also switch on. These lamps remain lit for
30, 60 or 90 seconds. A suitable time setting
can be made at a workshop - an authorised
Volvo workshop is recommended.
05
To extinguish the approach lighting:
Press the yellow button again.
Locking
Lock all doors, tailgate and fuel filler flap with
the button. There is a delay of approx.
10 minutes for the fuel filler flap.
Folding/opening key
The remote control key can be folded by pressing the button and folding the key blade section
into the keypad at the same time.
Replace the battery after repeated failure by
the locks to respond when remote control key
signals are transmitted within a normal distance.
1. Remove the cover by carefully prising up
the rear edge of with a small screwdriver.
2. Replace the battery (type CR 2032, 3 V) –
with the plus side facing up. Avoid touching the battery and its terminals with your
fingers.
* Option/accessory, for more information, see Introduction.
121
05 Locks and alarm
Locking and unlocking
Locking/unlocking the car from
outside
Automatic relocking
If none of the doors or the tailgate is opened
within 2 minutes of unlocking with the remote
control key then all are locked again automatically. This function prevents the car from being
left unlocked unintentionally.
For cars with alarms, see page 127.
7 km/h. They remain locked until a door is
opened from the inside or when all doors are
unlocked from the control panel.
Activating/deactivating
The remote control key must be in key position
I or II.
Press the READ button in the left-hand stalk
switch to acknowledge any messages on the
display.
Automatic locking
G026963
Press and hold the button for central locking
until a new message for lock status is shown in
the display.
05
The messages AUTOLOCK ACTIVATED (the
car is also locked when it moves) and
AUTOLOCK DEACTIVATED respectively are
shown on the display.
The fuel filler flap can be opened when the car
is unlocked. The flap remains unlocked for
10 minutes after the car has been locked.
NOTE
The car can be locked even if a door or the
tailgate is open. When the door is closed
there is a risk that the keys will be locked in.
1
122
Applies to certain markets
G029646
The remote control key locks/unlocks all side
doors and the tailgate simultaneously. The side
door lock buttons and inside handles are disengaged1.
Automatic locking is activated and deactivated
from the control panel in the driver's door. The
function operates by locking the doors automatically when the speed of the car exceeds
05 Locks and alarm
Locking and unlocking
Locking/unlocking the car from inside
Locking the glovebox
ATTENTION
Pakjdskdl ioiuip kjöpp opoodidåuswi
AIRBAG
MY KEY
L E CTOR
SE
SOUND
ENTER
G028485
EXIT
80
G027025
G029646
MENU
All the doors and the tailgate can be locked or
unlocked simultaneously using the control
panel in the driver's door (or passenger door).
The glovebox can be locked with the remote
control key's key blade.
All doors can be locked using the lock button
on the control panel by each respective door.
Locking/unlocking the tailgate
The alarm for the tailgate can be disarmed
and the tailgate unlocked on its own by
using the remote control key's *button.
If the car is equipped with an alarm* the alarm
indicator on the instrument panel stops to
show that alarm for the whole of the car is not
armed. The alarm's level and movement sensors and the sensors for opening the tailgate
are disconnected.
05
The doors remain locked and armed.
The tailgate can be opened in two
different ways
One press – The tailgate is unlocked but
remains closed. Disengage the lock with the
outside handle and open the tailgate.
If the tailgate is not opened within 2 minutes
then it is relocked and the alarm is re-armed.
``
* Option/accessory, for more information, see Introduction.
123
05 Locks and alarm
Locking and unlocking
NOTE
05
•
When the boot lid/tailgate is unlocked
with 2 presses, automatic relocking
does not take place because the boot
lid/tailgate is open - it must be closed
manually.
•
After the boot lid/tailgate has been
closed it is unlocked and the alarm is
not armed - relock it and re-arm the
alarm with the remote control key's
LOCK button.
must be closed before deadlocks can be activated.
The car can only be unlocked from a deadlock
state with the remote control key's UNLOCK
button. The driver's door can also be unlocked
with the key blade.
NOTE
When deadlocked, the doors cannot be
opened from the inside if they are locked.
2
124
2. Press the button. Note that the alarm's*
movement and tilt detectors are switched
off at the same time, see page 128.
Next time the engine is started the system is
reset to zero and the deadlocks function and
the alarm's movement and tilt detectors are
then re-engaged.
Deadlocks*2
The deadlocks function is activated from the
outside with the remote control key's LOCK
button, or by locking the driver's door with the
key blade, and is set after a 10-25 second delay
after the doors have been locked. All doors
1. Insert the remote control key into the ignition switch, turn it to key position II and
then back to position I or 0.
The lamp in the button illuminates until the car
is locked with the remote control key. A message is shown on the display as long as the
remote control key remains in the ignition
switch.
Temporary deactivation
G027230
Two presses – The tailgate is unlocked and
the lock plunger is disengaged, at which point
the tailgate is opened a few centimetres. Lift
the outside handle in order to open the tailgate.
Rain, cold, frost or snow could prevent the tailgate from disengaging from the lock plunger.
If someone is going to stay in the car but the
doors must be locked from the outside, then
the deadlocks function can be temporarily
switched off.
Only in combination with alarm.
* Option/accessory, for more information, see Introduction.
•
Remember that the car's alarm is armed
when the car is locked.
•
If any of the doors are opened from the
inside then the alarm will be triggered.
WARNING
Do not allow anyone to remain in the car
without deactivating the deadlocks function.
05 Locks and alarm
Child safety locks
Manual child safety locks – tailgate and
rear doors
Not child-safe position – the tailgate can be
opened from inside.
The controls for the child safety locks are in the
bottom edge of the tailgate and in the rear edge
of the rear doors. The controls are only accessible when the tailgate is open or the rear doors
are open.
Child-safe position – the rear doors cannot
be opened from inside; turn outwards.
Electric child safety locks – rear side
doors*
Rear doors
REAR
AC
G021512
G021513
G027105
Tailgate
Control for child safety lock – tailgate.
Adjust the tailgate control by sliding it sideways
between the outer positions (use a flat metal
object, such as a screwdriver):
Controls for the child safety locks – left and righthand rear doors.
Adjust the control in the respective rear door
by turning it between the outer positions (use
a flat metal object, such as a screwdriver).
Child-safe position – the rear doors cannot
be opened from inside: Turn outwards.
Not child-safe position – the rear doors can
be opened from inside: Turn inwards.
05
Use the button in the centre console to activate/deactivate the child safety locks in the
rear doors.
1. Turn the ignition key to position I or II, see
page 140.
2. Press the button.
When the light in the button illuminates, the
rear power windows and rear doors are locked.
A message appears on the display, the child
safety locks are activated/deactivated.
``
* Option/accessory, for more information, see Introduction.
125
05 Locks and alarm
Child safety locks
NOTE
As long as the child safety lock is activated
the rear doors cannot be opened from the
inside.
05
126
05 Locks and alarm
Alarm*
Alarm system
Alarm indicator
NOTE
When the alarm is armed, it continually monitors all alarm inputs.
Do not attempt to repair or modify alarm
system components. All such attempts
could affect the terms of insurance.
The alarm is triggered if:
• a door, the bonnet or tailgate opens
• a non-approved key is used in the ignition
Arming the alarm
or if an attempt is made to force the lock
• a movement is detected in the passenger
compartment (if fitted with a movement
detector)
• the car is raised or towed away (if fitted
IMPORTANT
G026963
with a tilt detector)
• a battery cable is disconnected
• anyone tries to disconnect the siren.
The alarm is fully armed when the car's
direction indicators have made one long
flash and the LED on the instrument panel
flashes once every other second.
A red LED on the instrument panel indicates
the alarm system's status:
• LED not lit – the alarm is not armed.
• The LED flashes once every other second
– Alarm is armed.
•
The LED flashes rapidly after disarming the
alarm and until the remote control key is
turned to key position II – the alarm has
been triggered.
If there is a fault in the alarm system, a message
appears on the display. At which point you
should contact a workshop - an authorised
Volvo workshop is recommended.
Press the LOCK button. A long flash from
the car's direction indicators confirms that
the alarm is armed and that all the doors
are locked.
05
Disarming the alarm
Press the remote control key's UNLOCK
button. Two short flashes from the car's
direction indicators confirm that the alarm
has been deactivated.
If the remote control key's batteries are discharged then the alarm can be disarmed by
turning the key to key position II.
``
* Option/accessory, for more information, see Introduction.
127
05 Locks and alarm
Alarm*
Automatic alarm activation
Alarm signals
This function prevents you accidentally leaving
the car without the alarm on.
When the alarm is triggered, the following happens:
1. Insert the remote control key into the ignition switch, turn it to key position II and
then back to position I or 0.
If none of the doors or the tailgate is opened
within two minutes of disarming the alarm (and
the car has been unlocked with the remote
control key), the alarm is automatically
rearmed. The car is locked at the same time.
• A siren sounds for less than 25 seconds.
2. Press the button.
The siren has its own battery which is used
if the car battery has insufficient charge or
is disconnected.
• All direction indicators flash for 5 minutes
or until the alarm is deactivated.
Automatic alarm activation
In certain countries (e.g. Belgium, Israel) the
alarm is activated after a certain delay if the
driver's door was opened and closed but the
car was not re-locked.
Reduced alarm level
Next time the engine is started the system is
reset to zero and the movement and tilt detectors and the deadlocks function are then reengaged.
05
Deactivating a triggered alarm
Press the remote control key's UNLOCK
button or insert it into the ignition switch.
G027230
Confirmation is given by two short flashes from
the direction indicators.
To avoid inadvertently triggering of the alarm for example when leaving a dog in the car or
during a ferry crossing - the movement and tilt
detectors can be temporarily switched off.
128
* Option/accessory, for more information, see Introduction.
The lamp in the button illuminates until you lock
the car. A message is shown on the display as
long as the remote control key remains in the
ignition switch. Note that the deadlocks function is switched off at the same time, see
page 124.
05 Locks and alarm
05
129
General..................................................................................................
Refuelling..............................................................................................
Starting the engine................................................................................
Manual gearbox....................................................................................
Automatic gearbox................................................................................
All-wheel drive*.....................................................................................
Brake system........................................................................................
Stability and traction control system* ..................................................
Parking assistance*...............................................................................
Blind Spot Information System - BLIS*.................................................
Towing and recovery.............................................................................
Start assistance....................................................................................
Driving with a trailer..............................................................................
Towing equipment* ..............................................................................
Detachable towbar* .............................................................................
Adjusting headlamp pattern .................................................................
130
* Option/accessory, for more information, see Introduction.
132
134
140
142
143
146
147
149
151
153
157
159
160
162
164
168
STARTING AND DRIVING
06 Starting and driving
General
Economical driving
Slippery driving conditions
Driving economically means driving smoothly
while thinking ahead and adjusting your driving
style and speed to the prevailing conditions.
For more advice on reducing environmental
impact. see page 13.
Practise driving on slippery surfaces under
controlled conditions to learn how the car
reacts.
• Do not run the engine to operating tem-
Under special conditions, for example when
driving in hilly terrain, extreme heat or with
heavy loads, there is a risk that the engine and
cooling system will overheat.
perature at idling speed, but rather drive
with a light load as soon as possible - a
cold engine consumes more fuel than a
warm one.
• Use the parking heater* in cold weather the engine reaches normal operating temperature more quickly.
• Avoid sudden unnecessary acceleration
Engine and cooling system
Avoid overheating the cooling system
• Maintain a low speed when driving with a
trailer up long, steep ascents.
• Do not turn the engine off immediately you
stop after a hard drive.
and heavy braking.
• Do not drive with unnecessary loads in the
• Remove any auxiliary lamps from in front
of the grille if driving in extreme high temperatures.
car.
06
• Remove the load carriers when not in use.
• Do not use winter tyres when the winter
season is over.
• Avoid driving with open windows.
132
Avoid overheating the engine
Do not exceed engine speeds of 4500 rpm
(diesel engines: 3500 rpm) if driving with a
trailer or caravan in hilly terrain. The oil temperature could then become too high.
* Option/accessory, for more information, see Introduction.
Open tailgate
WARNING
Do not drive with the tailgate open. Toxic
exhaust fumes can be drawn into the car
through the cargo area.
Driving on rough roads
The Volvo XC90 is primarily designed for driving on main roads, but also has good handling
properties on uneven or rough roads. Keep the
following in mind in order to preserve the service life of your car:
• Drive slowly on rough roads so you do not
damage the car's underbody.
• If the ground is loose or is made up of dry
sand or snow, it is always best to keep the
car moving at all times and avoid shifting.
Do not stop the car.
• If the road is extremely steep and there is
a risk of overturning, never try to turn the
car around. Reverse back down. Do not
drive diagonally across an incline. Drive in
the direction of the incline.
06 Starting and driving
General
NOTE
Avoid driving on steep slopes if the fuel level
is low. The catalytic converter could be
damaged if the engine does not receive
enough fuel. When driving on extremely
steep slopes, make sure the tank is more
than half full to avoid the risk of breakdown.
Driving in water
The car can be driven through water at a maximum depth of 40 cm at a maximum speed of
10 km/h. Extra caution should be exercised
when passing through flowing water.
NOTE
Clean the electric contacts of the electric
engine block heater and trailer coupling
after driving in water and mud.
IMPORTANT
Do not let the car stand with water over the
sills for any long period of time. This could
cause electrical malfunctions.
In the event of engine stop in water do not
try restart. Tow the car from the water.
• audio system (high volume)
• headlamps.
If the battery voltage is low the information display shows the text LOW BATTERY POWER
SAVE MODE. The energy-saving function
then shuts down certain functions or reduces
certain functions such as the ventilation fan
and/or audio system.
In which case, charge the battery by starting the engine and then running it for at
least 15 minutes - battery charging is more
effective during driving than running the
engine at idling speed while stationary.
Do not overload the battery
IMPORTANT
Engine damage can occur if water enters
the air filter.
In greater depths, water can enter the transmission. This reduces the lubricating ability
of the oils and shortens the service life of the
systems.
During driving in water, maintain a low speed
and do not stop the car. When the water has
been passed, depress the brake pedal lightly
and check that full brake function is achieved.
Water and mud for example can make the
brake linings wet resulting in delayed brake
function.
The electrical functions in the car load the battery to varying degrees. Avoid having the
remote control key in key position II when the
engine is switched off. Instead use the I mode
- which uses less power.
06
Note that the 12 volt outlet in the cargo area
supplies power even when the remote control
key has been removed from the ignition switch.
Also, be aware of different accessories that
load the electrical system. Do not use functions
which use a lot of power when the engine is
switched off. Examples of such functions are:
• ventilation fan
• windscreen wipers
133
06 Starting and driving
Refuelling
Opening the fuel filler flap
Emergency unlocking of the fuel filler
flap
G027073
The fuel filler flap can be opened manually
when necessary if it cannot be opened normally.
The fuel filler cap is inside the fuel filler flap on the
right-hand rear wing and hangs up on the inside of
the fuel filler flap.
06
The fuel filler flap can be opened when the car
is unlocked.
NOTE
The filler flap remains unlocked for ten
minutes after the car is locked. It then locks
automatically.
134
06 Starting and driving
G027077
Refuelling
Steps 1–3.
1. Lift up the corner piece from the floor in the
rear right-hand corner of the cargo area.
2. Open the fuel filler flap by lifting up the
handle and pulling it out.
3. Fold aside the insulation in order to access
the flap's electrical lock.
G027034
4. Insert your hand and locate the lock. Its
location is approximately inside the rear
edge of the fuel filler flap.
After refuelling the flap can be relocked by
closing it and pushing the lock plunger forward.
Proceed as follows:
06
WARNING
There are sharp edges behind the panel so
move your hands slowly and carefully.
5. Pull the lock plunger straight back. The flap
can now be folded out.
Steps 4–5.
``
135
06 Starting and driving
Refuelling
Fuel cap
A certain overpressure may arise in the tank in
the event of high outside temperatures. Open
the cap slowly
NOTE
Put the petrol cap back on after refuelling.
Turn until one or more clear clicks are heard.
Filling up with fuel
Do not overfill the tank but fill until the pump
nozzle cuts out.
NOTE
Excess fuel in the tank can overflow in hot
weather.
06
136
Fuel of a lower quality than that specified in this
chapter should not be used as engine power
and fuel consumption can be negatively affected.
General information on fuel
WARNING
Always avoid inhaling fuel vapour and getting fuel splashes in the eyes.
In the event of fuel in the eyes, remove any
contact lenses and rinse the eyes in plenty
of water for at least 15 minutes and seek
medical attention.
Never swallow fuel. Fuels such as petrol,
bioethanol and mixtures of them and diesel
are highly toxic and could cause permanent
injury or be fatal if swallowed. Seek medical
attention immediately if fuel has been swallowed.
WARNING
Fuel which spills on to the ground can be
ignited by the exhaust fumes.
Switch off the fuel-driven heater before starting to refuel.
Never carry an activated mobile phone
when refuelling. The ring signal could cause
spark build-up and ignite petrol fumes,
leading to fire and injury.
IMPORTANT
Mixing different types of fuel or the use of
fuel not recommended invalidates Volvo's
guarantees, and any associated service
agreement. This applies to all engines.
NOTE: It does not apply to cars with engines
that are adapted to run on ethanol fuel (E85).
For detailed information on CO2 emissions, fuel
consumption and tank volume, see page 281.
Petrol
Petrol must meet the EN 228 standard. Most
engines can be run with octane ratings of 91,
95 and 98 RON.
• 91 RON must not be used for 4-cylinder
engines and should only be used in exceptional cases with other engines.
• 95 RON can be used for normal driving.
• 98 RON is recommended for optimum performance and minimum fuel consumption.
When driving in temperatures above +38 °C,
fuel with the highest possible octane rating is
recommended for optimum performance and
fuel economy.
06 Starting and driving
Refuelling
IMPORTANT
Lambda-sondTM oxygen sensor
•
Always refuel with unleaded petrol so as
not to damage the catalytic converter.
•
Do not use additives not recommended
by Volvo.
The Lambda-sond is part of a control system
intended to reduce emissions and improve fuel
economy.
Catalytic converter
The purpose of the catalytic converter is to
purify exhaust gases. It is located in the flow of
exhaust gases close to the engine so that it
quickly reaches operating temperature. The
catalytic converter consists of a monolith
(ceramic or metal) with channels. The channel
walls are lined with a thin layer of platinum/rhodium/palladium. These metals act as catalysts,
i.e. they participate in and accelerate a chemical reaction without being used up themselves.
An oxygen sensor monitors the oxygen content
of the exhaust gases leaving the engine. This
value is fed into an electronic system that continuously controls the injectors. The ratio of fuel
to air directed to the engine is continuously
adjusted. These adjustments create optimal
conditions for efficient combustion of harmful
emissions (hydrocarbons, carbon monoxide
and nitrous oxides) using the three-way catalytic converter.
Diesel
Diesel must meet the EN 590 or JIS K2204
standards.
IMPORTANT
Only ever use fuel that fulfils the European
diesel standard.
IMPORTANT
Diesel type fuels which must not be used:
special additives, Marine Diesel Fuel, fuel
oil, RME1 (Rape Methyl Ester) and vegetable
oil. These fuels do not fulfil the requirements
in accordance with Volvo recommendations
and generate increased wear and engine
damage that is not covered by the Volvo
warranty.
Diesel engines are sensitive to contaminants,
such as excessively high volumes of sulphur
particles for example. Only use diesel fuel from
well-known producers. Never use diesel of
dubious quality.
At low temperatures (-40 °C to -6 °C), a paraffin
precipitate may form in the diesel fuel, which
may lead to ignition problems. Special diesel
fuel designed for low temperatures around
freezing point is available from the major oil
companies. This fuel is less viscous at low temperatures and reduces the risk of paraffin precipitate.
06
IMPORTANT
Use special winter grade fuel during cold
months.
1
Diesel fuel may contain a certain amount of RME, but further amounts must not be added.
``
137
06 Starting and driving
Refuelling
The risk of condensation in the fuel tank is
reduced if the tank is kept well filled. When
refuelling, check that the area around the fuel
filler pipe is clean. Avoid spilling fuel onto the
paintwork. Wash off any spillage with detergent and water.
IMPORTANT
The sulphur content must be a maximum of
50 ppm.
Empty tank
The design of the fuel system in a diesel engine
means that if the vehicle runs out of fuel, the
tank may need to be vented in the workshop in
order to restart the engine after fuelling.
06
Once the engine has stopped due to fuel starvation, the fuel system needs a few moments
to carry out a check. Do this before starting the
engine, once the fuel tank has been filled with
diesel:
1. Insert the remote control key in the ignition
switch and turn to key position II (see
page 140).
2. Wait approx. 1 minute.
3. To start the engine: Depress the brake and/
or clutch pedal, and turn the remote control
key to start position III.
138
Draining condensation from the fuel filter
The fuel filter separates condensation from the
fuel. Condensation can disrupt engine operation.
The fuel filter must be drained at the intervals
specified in the Service and Warranty Booklet
or if you suspect that the car has been filled
with contaminated fuel.
IMPORTANT
Certain special additives remove the water
separation in the fuel filter.
Diesel particle filter (DPF)
Diesel cars may be equipped with a particle filter, which results in more efficient emission
control. The particles in the exhaust gases are
collected in the filter during normal driving. Socalled "regeneration" is started in order to burn
away the particles and empty the filter. This
requires the engine to have reached normal
operating temperature.
Regeneration of the filter takes place automatically at an interval of approximately
300 – 900 km depending on driving conditions.
Regeneration normally takes 10 - 20 minutes.
It may take a little longer at a low average
speed. Fuel consumption may increase slightly
during regeneration.
The rear window heating may be activated
automatically to increase the load on the
engine during regeneration without warning.
Regeneration in cold weather
If the car is frequently driven short distances in
cold weather then the engine does not reach
normal operating temperature. This means that
regeneration of the diesel particle filter does
not take place and the filter is not emptied.
When the filter has become
approximately 80% full of particles, the yellow
information symbol on the instrument panel
illuminates, and the message SOOT FILTER
FULL - SEE MANUAL is shown on the instrument panel display.
Start regeneration of the filter by driving the car
until the engine reaches normal operating temperature, preferably on a main road or motorway. The car should then be driven for approximately 20 minutes more.
NOTE
A smaller reduction of engine power may be
noticed temporarily during regeneration.
When regeneration is complete the message is
cleared automatically.
06 Starting and driving
Refuelling
Use the parking heater* in cold weather so that
the engine reaches normal operating temperature more quickly.
IMPORTANT
If the filter fills up it may be incapable of
functioning. Then it can be difficult to start
the engine and there is a risk that the filter
will have to be replaced.
06
* Option/accessory, for more information, see Introduction.
139
06 Starting and driving
Starting the engine
Before starting the engine
NOTE
Apply the parking brake.
The idling speed can be noticeably higher
than normal for certain engine types during
cold starting. This is in order that the emissions system can reach normal operating
temperature as quickly as possible, which
minimises exhaust emissions and protects
the environment.
Automatic gearbox
Gear selector in position P or N.
Manual gearbox
Put the gear lever in neutral and hold the
clutch pedal fully depressed. This is particularly important in very cold conditions.
Starting the engine
WARNING
Never remove the remote control key from
the ignition switch while driving or when the
car is being towed. The steering lock could
otherwise be activated, making it impossible to steer the car.
The remote control key must be in key position II when the car is being towed.
Diesel
06
NOTE
The remote control key's key blade must be
fully extended when starting the car, see
page 120. Otherwise there is a risk that the
immobiliser function will prevent the car
from starting.
140
Petrol
Turn the remote control key to key position
III. If the engine does not start within
5-10 seconds, release the key and try
again.
1. Turn the remote control key to key position
II.
An indicator symbol in the combined
instrument panel shows that engine preheating is underway, see page 53.
2. Turn the ignition key to position III when
the indicator symbol goes out.
Ignition switch and steering lock
0 – Locked position
The steering lock is activated
when the remote control key
is removed from the ignition
switch.
I – Radio position
Certain electrical components can be switched on.
The engine's electrical system is not activated.
II – Driving position
The remote control key's
position when driving. The
car's electrical system is
energised.
06 Starting and driving
Starting the engine
III – Start position
The starter motor is engaged.
When the remote control key
is released it springs back
automatically to the driving
position, once the engine has
started.
If the key is hard to turn, the front wheels may
be turned in such a way that there is tension in
the steering wheel lock. In which case, turn the
wheel back and forth to make it easier to turn
the key.
Autostart (3.2 and V8)
Using the autostart function, the remote control key does not need to be kept in the start
position (key position III) until the engine has
started. Turn the key to the start position and
then release it - the starter motor then operates
automatically (up to 10 seconds) until the
engine has started.
NOTE
Remote control keys and electronic
immobiliser
The remote control key must not hang with
other keys or metal objects on the same key
ring. The electronic immobiliser could be activated accidentally.
Never rev up the engine hard immediately after
a cold start!
If the engine does not start or misfires, contact
a workshop - a Volvo workshop is recommended.
WARNING
You must never turn the remote control key
to key position I or 0 and never remove the
remote control key from the ignition switch
while the car is moving. The steering lock
could otherwise be activated, making it
impossible to steer the car.
06
Always remove the remote control key from
the ignition switch when leaving the car –
especially if children are left alone in the car.
Make sure the steering wheel locks when
you leave the car. This reduces the risk of
theft.
141
06 Starting and driving
Manual gearbox
G026988
Gear positions
1. Depress the clutch pedal fully during each
gear change.
06
2. Take your foot off the clutch pedal between
gear changes. Follow the shifting pattern
indicated.
Use 6th gear as often as possible for the best
possible fuel economy.
Reverse gear inhibitor
The reverse gear inhibitor hinders the possibility of mistakenly attempting to engage reverse
gear during normal forward travel.
Only engage reverse gear when the car is stationary.
142
06 Starting and driving
Automatic gearbox
Gear positions
The gearbox is mechanically blocked when
the P position is engaged. Always apply the
parking brake when parking the car.
Gear selector inhibitor
R – Reverse
The car must be stationary when position R is
selected.
N – Neutral
P – Parking position
Select position P when you wish to start the
engine or park the car.
IMPORTANT
The car must be stationary when position
P is selected.
D – Drive
D is the normal driving position. The car automatically shifts between the different gears of
the gearbox based on the level of acceleration
and speed. The car must be stationary when
the gear selector is moved to position D from
position R.
G020237
G027997
N is the neutral position. No gear is engaged
and the engine can be started. Apply the parking brake when the car is stationary with the
gear selector in position N.
The gear selector can always be moved freely
between N and D. Other positions are locked
with a latch that is released with the inhibitor
button on the gear selector.
06
With one press on the inhibitor button you can
move the lever forwards or backwards
between the gear positions, N, R and P.
NOTE
The brake pedal must be depressed to
move the gear lever from the P position.
``
143
06 Starting and driving
Automatic gearbox
Manual positions
While driving
Cold start
The manual gearshift mode can be selected at
any time while driving. The engaged gear is
locked until you choose another gear.
When starting in low temperatures, the gear
changes can sometimes feel hard. This is due
to the gearbox oil's viscosity at low temperatures. To reduce engine emissions, the gearbox shifts up later than normal when the engine
is started at low temperatures.
If the gear selector is moved to – (minus) the
car changes down a gear and engine brakes at
the same time as the accelerator pedal is
released. If the gear selector is moved to +
(plus) the car changes up a gear.
G026990
Third gear 3 is the highest gear that can be
used when starting.
06
To move from the automatic driving position
D to a manual position, move the gear selector
to position M. To go from position M to the
automatic driving position D, move the selector
to position D.
On the 5-speed automatic gearbox, gears 3,
4 and 51 have the Lock-up function (locked
gears), which provides better engine braking
and lower fuel consumption.
144
Depending on the engine temperature when
the engine is started, the idle speed after a
cold start may be higher than normal for
certain engine types.
W – Winter
Press the W button to activate and
deactivate the winter program.
Display of the W symbol in the
combined instrument panel indicates that the winter program is
active.
The winter programme starts the gearbox in
3rd gear to make it easier to pull off on slippery
roads. When the programme is engaged, lower
gears are activated only by kick-down.
The W program can be selected regardless of
the position of the gear selector, but is only
operational when the selector is in position D.
1
NOTE
2nd and 6th gear also have lock-up on the 6-speed automatic gearbox.
Adaptive system
The gearbox is controlled by what is known as
an adaptive system. The system continually
monitors how the gearbox is behaving and
senses every gear change for optimum change
quality.
Lock-up function
The gears have a lock-up function (locked
gears), which gives better engine braking and
lower fuel consumption.
06 Starting and driving
Automatic gearbox
Kick-down
When the accelerator pedal is pressed all the
way to the floor, beyond the position normally
regarded as full acceleration, a lower gear is
immediately engaged. This is known as kickdown.
Keep your foot on the brake pedal when
moving the gear selector to another position.
If the accelerator is released from the kickdown position, the gearbox automatically
changes up.
Kick-down is used when maximum acceleration is needed, such as for overtaking.
To prevent overrevving, the gearbox control
program has a protective downshift inhibitor
which prevents the kick-down function.
The kick-down function cannot be used in
manual gear position.
Safety systems
06
Cars with an automatic gearbox have special
safety systems:
Keylock
To remove the remote control key from the
ignition switch, the gear selector must be in the
P position. The key is locked in all other positions.
Parking position (P)
Stationary car with engine running:
145
06 Starting and driving
All-wheel drive*
All-wheel drive – AWD
All-wheel drive is always engaged.
All-wheel drive means that all four road wheels
are driven at the same time. The power is automatically distributed between the front and rear
wheels. An electronically controlled clutch system distributes the power to the pair of wheels
that grips best. This provides the best traction
and prevents wheel spin.
Under normal driving conditions, the majority
of power is transmitted to the front wheels.
All-wheel drive improves driving safety in rain,
snow and icy conditions.
06
146
* Option/accessory, for more information, see Introduction.
06 Starting and driving
Brake system
Brake servo
If the car is rolling or is being towed with the
engine turned off, the brake pedal must be
pressed about five times harder than when the
engine is running. If the brake pedal is
depressed when the engine is started, you will
feel the pedal drop. This is normal and due to
the brake servo becoming active. This may be
more noticeable if the car has Emergency
Brake Assistance (EBA).
WARNING
The brake servo only works when the engine
is running.
NOTE
If braking with the engine switched off,
press the brake pedal sharply once, not
repeatedly.
Brake circuits
This symbol illuminates if a brake
circuit is not working.
If a fault should occur in one of the
circuits, it is still possible to brake
the car. The brake pedal will travel further and
may feel softer than normal. Harder pressure
on the pedal is needed to produce the normal
braking effect.
Dampness can affect braking
characteristics
Brake components become wet when the car
is driven in heavy rain, through pools of water
or when the car is washed. This may alter brake
pad friction characteristics so that there is a
delay before braking effect is noticed.
Press the brake pedal lightly from time to time
if driving for long stretches in rain or slushy
snow, as well as after setting off in very damp
or cold weather. This warms up the brake pads
and dries off any water. This precaution is also
recommended before parking the car for a long
period in such weather conditions.
Bear in mind that driving with a trailer puts an
additional load on the car's brakes.
Anti-lock braking system (ABS)
The anti-lock braking system
(ABS) prevents the wheels from
locking up during braking.
This means the ability to steer is
maintained and it is easier to swerve to avoid a
hazard for example.
After the engine has been started, the ABS will
perform a brief self-test at a speed of
about 20 km/h. This can be felt and heard as
pulses in the brake pedal.
If the brakes are used heavily
To get the most out of the ABS:
When driving in the Alps or other roads with
similar characteristics, the car's brakes are
heavily loaded even if the brake pedal is not
being depressed especially hard.
1. Depress the brake pedal with full force.
Pulses will be felt.
Because speed is often low, the brakes are not
cooled as effectively as when driving on flat
roads at higher speed.
So as not to overload the brakes, shift down
when driving downhill instead of using the foot
brake. Use the same gear driving downhill as
you would use driving uphill. This uses engine
braking more efficiently so the foot brake is
only required for brief periods.
2. Steer the car in the direction of travel. Do
not release the pressure on the pedal.
06
Practice braking with the ABS system in a traffic-free area and in different weather conditions.
The ABS symbol illuminates for two seconds if
there was a fault in the ABS system when the
engine was last running.
``
147
06 Starting and driving
Brake system
Electronic brake force distribution
system – EBD
The Electronic Brakeforce Distribution system
(EBD) is an integrated part of the ABS system.
The EBD system controls the brake force to the
rear wheels so that the best possible braking
force is always available. Pulses will be heard
and felt through the brake pedal when the system regulates brake force.
WARNING
If the BRAKE and ABS warning symbols illuminate at the same time, there may be a
fault in the brake system. If the level in the
brake fluid reservoir is normal at this stage,
drive carefully to the nearest workshop and
have the brake system checked - an authorised Volvo workshop is recommended.
06
If the brake fluid is under the MIN level in the
brake fluid reservoir, do not drive further
before topping up the brake fluid.
The reason for the loss of brake fluid must
be investigated.
148
Emergency Brake Assistance – EBA
(Emergency Brake Assistance) For sudden
braking, full-strength braking is provided
instantaneously. The EBA function senses
when heavy braking is underway by registering
how quickly the brake pedal is depressed.
Continue braking without easing off on the
brake pedal. The function is suspended when
the pressure on the brake pedal eases. This
function is always active. It cannot be disengaged.
NOTE
When EBA is activated the brake pedal lowers slightly more than usual, depress (hold)
the brake pedal as long as necessary. If the
brake pedal is released then all braking
ceases.
06 Starting and driving
Stability and traction control system*
General
Reduced operation
DSTC SPIN CONTROL OFF means that
system operation is reduced.
The Dynamic Stability and Traction Control
system (DSTC) improves the car's traction and
helps the driver to avoid skidding.
2. Press and hold RESET (2) until the DSTC
menu is changed.
A pulsing sound may be noticed during braking
or acceleration when the system is in action.
The car may accelerate slower than expected
when the accelerator pedal is depressed.
The system remains reduced until the
driver reactivates it or until the engine is
switched off - after the engine is started the
next time the DSTC is back in its normal
mode again.
Active Yaw Control
Spin Control
The function prevents the driving wheels from
spinning against the road surface during acceleration.
Traction control system
The function is active at low speed and transfers power from the driving wheel that is spinning to the one that is not.
G028511
The function limits the driving and brake force
of the wheels individually in order to stabilise
the car.
WARNING
Suppressing system function may alter the
driving characteristics of the car.
Thumbwheel
RESET button
NOTE
System operation during skidding and acceleration can be partially deactivated.
Operation during skidding is then delayed and
so allows more skidding which provides
greater freedom for dynamic driving. Traction
in deep snow or sand is improved at the same
time as acceleration is no longer limited.
Operation
1. Turn the thumbwheel (1) until the DSTC
menu appears.
DSTC ON means that the system function
is unchanged.
DSTC ON is shown for several seconds on
the display each time the engine is started.
06
Messages in the display
TRACTION CONTROL TEMPORARILY OFF
means that the system has been temporarily
reduced due to excessive brake temperature.
The function is reactivated automatically
when the brakes have cooled.
DSTC SERVICE REQUIRED system disabled
due to a fault.
``
* Option/accessory, for more information, see Introduction.
149
06 Starting and driving
Stability and traction control system*
Stop the car in a safe place and turn off the
engine.
> If the message remains when the engine
is restarted, drive to a workshop. An
authorised Volvo workshop is recommended.
Symbols in the combined instrument
panel
DSTC system
• If the warning symbol goes out, the fault
was temporary and it is not necessary to
visit a workshop.
• If the warning symbol remains illuminated
then a workshop should check the system
- an authorised Volvo workshop is recommended.
The symbol illuminates with a constant
yellow glow
Symbol for Warning
At the same time the display shows
TRACTION CONTROL
TEMPORARILY OFF.
The symbol illuminates and goes out
again after approx. 2 seconds when the
engine is started
• Indicates system check.
The symbol flashes
06
• Indicates that the system is operating.
The symbol illuminates and stays lit
At the same time the display shows DSTC
SERVICE REQUIRED.
• Indicates a fault in the DSTC system.
1. Stop the car in a safe place and turn off the
engine.
2. Restart the engine.
150
• Indicates that the system has been temporarily reduced due to excessive brake
temperature.
Automatic reactivation of the function takes
place when the brake temperature has
returned to normal.
WARNING
Under normal driving conditions, the
DSTC system improves the car's road
safety, but this should not be taken as a
reason to increase speed.
Always follow the usual precautions for safe
cornering and driving on slippery road surfaces.
* Option/accessory, for more information, see Introduction.
06 Starting and driving
Parking assistance*
General1
Variants
Rear parking assistance
Parking assistance is available in two variants:
The distance covered to the rear of the car is
about 1.5 m. Rear parking assistance is activated when reverse gear is engaged. The signal comes from the rear loudspeakers.
•
• Both front and rear
Rear only
Function
Parking assistance front and rear.
Parking assistance is used as an aid to parking.
A signal indicates the distance to a detected
object.
WARNING
Parking assistance does not relinquish the
driver's own responsibility during parking.
The sensors have blind spots where objects
cannot be detected. Be aware of children
and animals near the car.
1
The system is switched on automatically when
the car is started at which point the lamp in the
switch for parking assistance illuminates.
The system must be deactivated when reversing with a trailer, or bike carrier on the towbar
or similar. Otherwise the trailer or bike carrier
would trigger the sensors.
The display shows the text message PARK
ASSIST ACTIVE if reverse gear is engaged or
if the front sensors detect an object.
Rear parking assistance is deactivated automatically when towing a trailer if a Volvo genuine trailer cable is used.
Parking assistance is active at speeds below
15 km/h. The system is deactivated at higher
speeds. When the speed is below 10 km/h the
system is reactivated.
Front parking assistance
The frequency of the signal increases as you
come closer to an object in front of or behind
the car. If the volume of another audio source
from the audio system is high, then this is automatically lowered.
Front parking assistance cannot be combined
with extra lights because the sensors are affected by the extra lights.
The tone becomes constant at a distance of
about 30 cm. If there are objects within this
distance behind or in front of the car, the signal
alternates between left and right-hand speakers.
If the information symbol illuminates with constant glow and the
display shows PARK ASSIST
SERVICE REQUIRED then parking assistance is disengaged.
The distance covered to the front of the car is
about 0.8 metres. The signal comes from the
front loudspeakers.
06
Fault indicator
Depending on the market, the Parking assistance system may be either Standard, Option or Accessory.
``
* Option/accessory, for more information, see Introduction.
151
06 Starting and driving
Parking assistance*
IMPORTANT
In certain conditions the parking assistance
system may produce incorrect warning signals that are caused by external sound
sources that emit the same ultrasonic frequencies that the system works with.
switched on again with the switch and the lamp
illuminates.
Cleaning the sensors
Examples of such sources include horns,
wet tyres on asphalt, pneumatic brakes and
exhaust noises from motorcycles etc.
G026946
Off/On
Parking assistance sensors.
06
G027104
The sensors must be cleaned regularly to
ensure that they work properly. Clean them
with water and car shampoo.
Button position in the row may vary.
Parking assistance can be deactivated with the
button in the switch panel. The lamp in the
switch goes out. Parking assistance is
152
NOTE
Dirt, ice and snow covering the sensors may
cause incorrect warning signals.
* Option/accessory, for more information, see Introduction.
06 Starting and driving
Blind Spot Information System - BLIS*
General
BLIS is an information system that under certain conditions can help to draw the driver's
attention to vehicles moving in the same direction in the so-called "blind spot".
Blind spots
The system is designed to work most effectively when driving in dense traffic on multi-lane
highways.
G020295
BLIS is based on digital camera technology.
The cameras (1) are located under the door
mirrors.
Rearview mirror with BLIS system.
BLIS camera
Indicator lamp
BLIS symbol
WARNING
The system is a supplement to, not a
replacement for, a safe driving style and use
of the rearview mirrors. It can never replace
the driver's attention and responsibility. The
responsibility for changing lanes safely
always rests with the driver.
When a camera has detected a vehicle inside
the blind spot zone the indicator lamp (2) illuminates with a constant glow.
NOTE
The lamp illuminates on the side of the car
where the system has detected the vehicle.
If the car is overtaken on both sides at the
same time then both lamps illuminate.
BLIS advises the driver with a message if a fault
arises in the system. If for example the system's cameras are obscured then the BLIS
indicator lamp flashes and a message is shown
in the information display. In such cases, check
and clean the lenses. If necessary, the system
can be switched off temporarily by pressing the
BLIS button, see page 154.
"Blind spots" intended to be covered by BLIS
cameras.
Distance A = approx. 3.0 m
Distance B = approx. 9.5 m
06
Cleaning
In order to work most effectively the BLIS camera lenses must be clean. The lenses can be
cleaned with a soft cloth or damp sponge.
Clean the lenses carefully so that they are not
scratched.
``
* Option/accessory, for more information, see Introduction.
153
06 Starting and driving
Blind Spot Information System - BLIS*
The lenses are electrically heated to melt ice
or snow. If necessary, brush snow away
from the lenses.
When BLIS operates
The system operates when the car is driven at
a speed above 10 km/h.
designed to detect motor vehicles such as
cars, trucks, buses and motorcycles.
In darkness the system reacts to the headlamps of surrounding vehicles. Vehicles with
headlamps that are switched off are not
detected by the system. This means for example that the system does not react to a trailer
without headlamps which is towed behind a
car or truck.
Overtaking
06
WARNING
The system is designed to react if you overtake
another vehicle at a speed of up to 10 km/h
faster than the other vehicle.
The system does not react to cyclists or
moped riders.
The system is designed to react if you are overtaken by a vehicle travelling up to 70 km/h
faster than your vehicle.
The BLIS cameras have limitations similar to
those of the human eye, i.e. they do not see
as well in e.g. heavy snowfall, strong
oncoming light or thick fog.
WARNING
BLIS does not work in sharp bends.
BLIS does not work when the car is reversing.
A wide trailer coupled to the car can conceal
other vehicles in adjacent lanes. It can prevent the vehicle in the screened area from
being detected by BLIS.
Daylight and darkness
In daylight the system reacts to the shape of
the surrounding vehicles. The system is
154
Activating/deactivating
* Option/accessory, for more information, see Introduction.
G026955
IMPORTANT
Button for activating/deactivating.
BLIS is activated when the engine is started.
The indicator lamps in the door panels flash
three times when BLIS is activated.
The system can be deactivated/activated by
pressing BLIS.
When BLIS is deactivated the light in the button
goes out and a text message is shown on the
instrument panel display.
When BLIS is activated the light in the button
illuminates, a new text message is shown on
the display and the indicator lamps in the door
panels flash three times. Press the READ button to clear the text message. For more information on messages, see page 54.
06 Starting and driving
Blind Spot Information System - BLIS*
BLIS system message
Text on the displayA
Specification
BLIND-SPOT INFO
SYSTEM ON
The BLIS system is
activated.
BLIND-SPOT
SYST L CAMERA
BLOCKED
Left camera blocked
- clean the lens.
BLIND-SPOT
SYST SERVICE
REQUIRED
Blind spot syst. disengaged - contact a
workshop.
BLIND-SPOT
SYST CAMERAS
BLOCKED
One or both cameras blocked - clean
the lenses.
BLIND-SPOT
SYST FUNCTION
REDUCED
Reduced function in
the data transmission between the
BLIS system's camera and the car's
electrical system.
BLIND-SPOT INFO
SYSTEM OFF
The BLIS system is
deactivated.
The camera resets
itself when the data
transmission
between the BLIS
system's camera
and the car's electrical system returns to
normal.
BLIND-SPOT
SYST R CAMERA
BLOCKED
Right camera
blocked - clean the
lens.
A
Specification
Limitations
Text on the displayA
In some situations the BLIS indicator lamp may
illuminate despite there being no other vehicle
within the blind spot.
NOTE
Messages above are only shown if the remote control key is
in key position II (or if the engine is running) and BLIS is
active (i.e. if the driver has not switched off the system).
IMPORTANT
Repair of the BLIS system components
must only be performed by a workshop - an
authorised Volvo workshop is recommended.
If the BLIS indicator lamp illuminates on isolated occasions despite there being no
other vehicle within the blind spot then this
does not mean that a fault has arisen in the
system.
In the event of a fault in the BLIS system the
display shows the text BLIS Serv.
required.
Here are several examples of situations where
the BLIS indicator lamp may illuminate even if
there is no other vehicle within the blind spot.
06
Reflection from shiny wet road surface.
``
* Option/accessory, for more information, see Introduction.
155
06 Starting and driving
G018177
Blind Spot Information System - BLIS*
Own shadow on large, light, smooth surface, e.g.
noise barrier or concrete road surface.
Low sun in the camera.
06
156
* Option/accessory, for more information, see Introduction.
06 Starting and driving
Towing and recovery
Start assistance
WARNING
Use a donor battery if the battery is discharged
and the engine does not start. Do not tow the
car to bump start it, see page 159.
The steering lock remains in the position it
was in when the power was cut off. The
steering lock must be unlocked before towing.
IMPORTANT
The remote control key must be in key position II. Never remove the remote control key
from the ignition switch while driving or
when the car is being towed.
Bump starting the car can damage the catalytic converter.
Towing
The towing eye is in the tool kit in the cargo
area.
The brake servo and power steering do not
work when the engine is switched off. The
brake pedal must be pressed about five
times harder than normal, and the steering
will be considerably heavier than normal.
The car must always be towed facing forward.
1. Unlock the steering wheel lock so that the
car can be steered.
Manual gearbox
Move gear lever into neutral and release
the parking brake.
06
Automatic gearbox
Move the gear selector to position N and
release the parking brake.
Cars with automatic gearbox must not be
towed at speeds above 80 km/h or further than
80 km.
G028528
For the driver of the vehicle being towed:
Keep the towline taut by holding your foot
gently pressed on the brake pedal in order
to avoid unnecessary jerking.
Before towing the towing eye must be bolted
securely onto the bumper. The socket and
cover for the towing eye are on the right-hand
side of each bumper.
WARNING
Find out the highest legal speed for towing
before towing the car.
2. For the driver of the towing vehicle: Drive
gently.
Towing eye
``
157
06 Starting and driving
Towing and recovery
Proceed as follows:
1. Release the bottom edge of the cover (A)
with a screwdriver or a coin.
2. Screw in the towing eye (B).
3. Screw the eye securely into place right up
to the flange (C). You can use a wheel
wrench.
• After use, unscrew the towing eye and refit
the cover.
IMPORTANT
On certain cars with fitted towbar the towing
eye cannot be secured in the rear mounting.
In which case, secure the tow rope in the
towbar. For this reason, it is advisable to
always store the detachable towbar in the
car.
06
Recovery
The car must always be towed with the wheels
rolling forward.
IMPORTANT
•
158
An all-wheel drive car (AWD) with raised
front suspension must not be towed at
speeds above 70 km/h. It should not be
towed further than 50 km.
WARNING
The towing eye is only designed for towing
on roads - not for recovering the car. Call a
recovery service for recovery assistance.
06 Starting and driving
Start assistance
Starting with a donor battery
3. If the donor battery is in another car, switch
off the engine in the other car and ensure
that the cars do not touch one another.
4. Connect the red jump lead between the
positive terminal on the donor battery (1+)
and the positive terminal in your car (2+).
5. Connect one end of the black jump lead to
the donor battery's negative terminal (3–).
G020298
6. Connect the other end of the black jump
lead to the earthing point (4–) by the lefthand strut tower.
If the battery in the car has become discharged, you can "borrow" electric current
from either a separate battery or from another
car. Always make sure the crocodile clips on
the jump leads are attached securely to eliminate sparks during the start attempt.
When jump starting the car, the following steps
are recommended to avoid risk of explosion:
1. Turn the remote control key to key position
0.
2. Ensure that the other battery is 12 volt.
WARNING
The battery can generate oxyhydrogen gas,
which is highly explosive. One spark, which
can be generated if you connect the jump
leads incorrectly, is sufficient to make the
battery explode.
The battery contains sulphuric acid, which
can cause serious burns. If the acid comes
into contact with eyes, skin or clothing, flush
with large quantities of water.
If acid splashes into the eyes, seek medical
attention immediately.
7. Start the engine of the "donor car". Let the
engine run a few minutes at a speed slightly
higher than idle (1500 rpm).
8. Start the engine of the car with the flat battery.
Remove the jump leads - first the black and
then the red.
06
Make sure that none of the clamps on the
black jump lead comes into contact with
the battery's positive terminal or the clamp
connected to the red jump lead.
IMPORTANT
Do not touch the crocodile clips during the
start procedure. There is a risk of sparks
forming.
159
06 Starting and driving
Driving with a trailer
General
Payload depends on the car's kerb weight. The
total of the weight of the passengers and all
accessories, e.g. towbar, reduces the car's
payload by a corresponding weight. For more
detailed information on weights, see
page 274.
If the towing bracket is fitted by an authorised
Volvo workshop, then the car is delivered with
the necessary equipment for driving with a
trailer.
• The car's towing bracket must be of an
approved type.
• If the towbar is retrofitted, check with your
Volvo dealer that the car is fully equipped
for driving with a trailer.
•
06
Distribute the load on the trailer so that the
weight on the towing bracket follows the
specified maximum towball load.
• Increase the tyre pressure to the recommended pressure for a full load. For tyre
pressure decal location, see page 178.
• Clean the towing bracket regularly and
grease the towball1.
• Do not tow a heavy trailer when the car is
brand new. Wait until it has been driven at
least 1000 km.
1
160
Does not apply to the towball if using a stabiliser hitch.
• The brakes are loaded much more than
usual on long and steep downhill slopes.
Downshift to a lower gear and adjust your
speed.
• The engine is loaded more heavily than
usual when driving with a trailer.
• The engine and gearbox can overheat if the
car is driven with a heavy load in hot
weather. If the temperature gauge for the
engine's cooling system goes into the red
zone, stop and let the engine idle for a few
minutes. The automatic gearbox responds
through a built-in protection system. See
the message on the information display. If
the car overheats, the air conditioning may
be switched off temporarily.
• In the interests of safety, speed should be
restricted to 80 km/h, even if the laws of
certain countries allow for higher speeds.
• Move the gear selector to park position P
when parking an automatic car with a
hitched trailer. Always use the parking
brake. Block the wheels with chocks when
parking a car with hitched trailer on a hill.
Trailer weights
Information on permitted trailer weights, see
page 274.
WARNING
Follow the stated recommendations for
trailer weights. Otherwise, the car and trailer
may be difficult to control in the event of
sudden movement and braking.
NOTE
The stated maximum permitted trailer
weights are those permitted by Volvo.
National vehicle regulations can further limit
trailer weights and speeds. Towbars can be
certified for higher towing weights than the
car can actually tow.
Automatic gearbox, driving with a
trailer
NOTE
Some models require an oil cooler for the
automatic gearbox when driving with a
trailer. Check with your nearest Volvo dealer
as to what applies to your car if you have a
retrofitted towbar.
06 Starting and driving
Driving with a trailer
Parking on a hill
Activating
1. Apply the parking brake.
To activate, the cables from the trailer must be
connected to the trailer socket which is fitted
beside the towbar, see page 162.
2. Move the gear selector to parking position
P.
Deactivating
Starting on a hill
1. Move the gear selector to driving position D.
2. Release the parking brake (foot brake
pedal).
Steep inclines
• Select an appropriate manual gear position
when climbing steep inclines or at low
speeds. This prevents the gearbox from
changing up and keeps the gearbox oil
cooler.
• Do not use a higher manual gear than the
engine can "handle". It is not always economical to drive in high gears.
• Avoid driving with a trailer on inclines of
Unplug the cables from the electrical socket.
NOTE
The function is also activated when any
other electrical equipment is plugged into
the trailer socket. The car then accelerates
more gently when pulling away.
Levelling
If your car is equipped with automatic levelling,
the rear suspension always retains the correct
ride height regardless of load. When the car is
stationary, the rear suspension sinks. This is
completely normal. When starting with a load,
the level is pumped up after a certain distance.
06
more than 12%.
Assisted starting with a trailer
Cars equipped with a V8 engine have an integrated function which reduces the risk of significant jerking and wheelspin when starting
with a trailer hitched to the car.
161
06 Starting and driving
Towing equipment*
Towbar
Trailer cable
Storing the towbar
If the car is equipped with a detachable towbar,
the installation instructions for the loose section must be followed carefully, see
page 164.
WARNING
Follow the installation instructions carefully.
•
The detachable section must be locked
with the key before setting off.
•
Check that the indicator window shows
green.
Towbar storage space.
IMPORTANT
Important checks
06
• The towbar's towball must be cleaned and
greased regularly.
Always remove the towbar after use and
store it in the appointed location in the car,
firmly fastened with its strap.
NOTE
If a towball hitch with vibration damper is
used, it is not necessary to grease the towball.
162
* Option/accessory, for more information, see Introduction.
G014589
•
G031114
If the car is fitted with a Volvo detachable
towbar:
An adapter is required if the car's towing
bracket has 13 pin electrics and the trailer has
7 pin electrics. Use an adapter cable approved
by Volvo. Make sure the cable does not drag
on the ground.
06 Starting and driving
Towing equipment*
G027109
G026682
G027108
Specifications
Dimensions for mounting points (mm)
Fixed or detachable towbar
A
B
C
D
E
F
G
1110
85
1081
541
122
50
354
1
Side member
2
Ball centre
* Option/accessory, for more information, see Introduction.
06
163
06 Starting and driving
Detachable towbar*
1. Remove the protective cover by first pressing in the catch
and then pulling the
cover straight back
.
2. Ensure that the mechanism is in the
unlocked position by turning the key clockwise.
06
164
* Option/accessory, for more information, see Introduction.
G020302
G017317
G020301
Fitting the towbar
3. Check that the indicator window (3) shows
red. If the window does not show red,
press in (1) and turn the locking wheel anticlockwise (2) until you hear a click.
06 Starting and driving
Detachable towbar*
G020309
G020307
G020304
5. Check that the indicator window shows
green.
4. Insert the towbar until you hear a click.
6. Turn the key anticlockwise to locked position. Remove the key from the lock.
7. Check that the towbar is secure by pulling
it up, down and back.
WARNING
If the towbar is not fitted correctly then it
must be detached and reattached in
accordance with the previous instructions.
06
IMPORTANT
G020306
Only grease in the ball for the towing hitch,
the remainder of the towbar should be clean
and dry.
``
* Option/accessory, for more information, see Introduction.
165
06 Starting and driving
Detachable towbar*
8. Safety cable.
WARNING
06
166
1. Insert the key and turn it clockwise to the
unlocked position.
Be sure to attach the trailer's safety cable to
the correct place.
* Option/accessory, for more information, see Introduction.
G020312
G020301
G020310
Removing the towbar
2. Push in the locking wheel (1) and turn it
anticlockwise (2) until you hear a click.
06 Starting and driving
3. Turn the locking wheel down fully, until it
comes to a stop. Hold it in this position
while pulling the towbar rearward and
upward.
G017318
G020314
Detachable towbar*
4. Push on the protective cover.
06
WARNING
Secure the towbar safely if it is stored in the
car, see page 162.
* Option/accessory, for more information, see Introduction.
167
06 Starting and driving
Adjusting headlamp pattern
Correct light pattern for left or righthand traffic
should align with the red dot on the respective
template. The long red line on the illustrations
corresponds to the line in the headlamp lens to
which the template should be matched.
After copying the templates, check the measurements so that the reference measurements
cover enough of the beam pattern.
The templates are for both LHD and RHD variants and are positioned as illustrated.
G020317
The upper illustration is for LHD cars. The lower
illustration is for RHD cars.
Headlamp pattern for left-hand traffic.
Headlamp pattern for right-hand traffic.
06
So as not to dazzle oncoming drivers, the
headlamp beam pattern can be altered by
masking the headlamps. The quality of the
beam pattern may not be as good.
Headlamp masking
Copy the templates, see page 168. Transfer
the pattern to a self-adhesive, waterproof
material such as opaque tape for example.
The mask is positioned using the dot (5) in the
headlamp lens as a reference point, which
168
Halogen headlamps
Copy templates 1 and 2. Check the measurements to ensure they are correct. Transfer the
template to a self-adhesive, waterproof material and cut it out.
Position each template so that the arrows point
towards the centre and the dot on the template
matches the dot on the headlamp lens.
Reference measurements template 1
and 2
The long sides of the templates should be
approx. 82 mm.
Xenon headlamps
Copy templates 3 and 4. Check the measurements to ensure they are correct. Transfer the
template to a self-adhesive, waterproof material and cut it out.
Position each template so that the arrows point
towards the centre and the dot on the template
matches the dot on the headlamp lens. The
template marking > < should be aligned with
the line on the headlamp lens.
Reference measurements template 3
The line between the > < markings on the templates should be approx. 140 mm.
Reference measurements template 4
The line between the > < markings on the templates should be approx. 112 mm.
Adjusting headlamp pattern for Active Xenon
headlamps (ABL), see page 56.
06 Starting and driving
G030200
Adjusting headlamp pattern
Left-hand drive car in left-hand traffic.
Masking on right-hand halogen lens
Masking on left-hand halogen lens
Masking on right-hand Xenon lens
06
Masking on left-hand Xenon lens
Control point in headlamp lens.
``
169
06 Starting and driving
G030201
Adjusting headlamp pattern
Right-hand drive car in right-hand traffic.
Masking on left-hand halogen lens
Masking on right-hand halogen lens
06
Masking on left-hand Xenon lens
Masking on right-hand Xenon lens
Control point in headlamp lens.
170
06 Starting and driving
Adjusting headlamp pattern
G027103
06
Templates for masking.
171
General..................................................................................................
Tyre pressure .......................................................................................
Warning triangle* and spare wheel * ....................................................
Changing wheels ..................................................................................
Emergency puncture repair* ................................................................
172
* Option/accessory, for more information, see Introduction.
174
177
179
182
184
WHEELS AND TYRES
07 Wheels and tyres
General
Driving characteristics and tyres
Speed ratings
The tyres greatly affect the car's driving characteristics. The type of tyre, dimensions, tyre
pressure and speed rating are important for
how the car performs.
The car is approved as a whole, which means
that dimensions and speed ratings must not
differ from those specified on the vehicle registration document. The only exception to
these conditions is winter tyres (both those
with metal studs and those without). If such a
tyre is chosen, the car must not be driven faster
than the speed rating of the tyre (for example,
class Q can be driven at a maximum of
160 km/h).
When changing tyres, ensure that tyres of the
same type and dimensions, and preferably also
the same make, are fitted to all four wheels.
Follow the recommended tyre pressures
specified on the tyre pressure label, for location
see page 177.
Designation of dimensions
The dimensions are stated on all car tyres.
Example of designation:
235/60R18 103 V.
07
174
235
Tyre width (mm)
60
Ratio between tyre wall height and
tyre width (%)
New tyres
Remember that traffic regulations determine
how fast a car can be driven, not the speed
class of the tyres.
Note! Maximum permitted speeds indicated.
Q
160 km/h (used only
on winter tyres)
T
190 km/h
H
210 km/h
R
Radial ply
V
240 km/h
18
Rim diameter in inches (")
W
270 km/h
103
Tyre load index (in this case 615 kg)
Y
300 km/h
V
Speed rating for maximum permitted speed (in this case 210 km/h).
Tyres are perishable. After a few years they
begin to harden at the same time as the friction
capacity/characteristics gradually deteriorate.
For this reason, aim to get as fresh tyres as
possible when you replace them. This is especially important with regard to winter tyres. The
last four digits in the sequence mean the week
and year of manufacture. This is the tyre's
DOT marking (Department of Transportation),
and this is stated with four digits, for example
1510. The tyre in the illustration was manufactured in week 15 of 2010.
Tyre age
All tyres older than six years should be checked
by an expert even if they seem undamaged.
07 Wheels and tyres
General
The reason for this is that tyres age and decompose, even if they are hardly ever or never used.
The function can therefore be affected due to
the tyre's constituent materials being broken
down. In such a case the tyre should then not
be used.This also applies to spare tyres, winter
tyres and tyres saved for future use. Examples
of external signs which indicate that the tyre is
unsuitable for use are cracks or discoloration.
wards in a straight line rather than having the
rear end skidding to one side, resulting in possible complete loss of control over the car. This
is why it is important for the rear wheels never
to lose grip before the front wheels.
Wheels should be stored lying down or hanging
up, and not standing up.
Tyres with tread wear indicators
The age of the tyre can be determined by the
DOT marking, see illustration above.
Winter tyres
Volvo recommends winter tyres with specific
winter tyre dimensions. Tyre dimensions are
dependent on engine variant. When driving on
winter tyres, they must be fitted to all four
wheels.
NOTE
Ask a Volvo dealer which rim and tyre types
are most suitable.
More even wear and maintenance
Studded tyres
Studded winter tyres should be run in gently for
500 – 1000 km so the studs settle properly into
the tyre. This gives the tyre, and especially the
studs, a longer service life.
G020323
The correct tyre pressure results in more even
wear, see page 178. Driving style, tyre pressure, climate and road condition affect how
quickly your tyres age and wear. To avoid differences in tread depth and to prevent wear
patterns arising, the front and rear wheels can
be switched with each other. A suitable distance for the first change is approx. 5000 km
and then at 10 000 km intervals. Volvo recommends that you contact an authorised Volvo
workshop for checking if you are uncertain
about tread depth. If significant differences in
wear (>1 mm difference in tread depth)
between tyres have already occurred, the least
worn tyres must always be placed on the rear.
Understeer is normally easier to correct than
oversteer, and leads to the car continuing for-
tyres with little tread depth provide very poor
grip in rain and snow.
Tread wear indicators.
Tread wear indicators are narrow treadless
bands across the width of the tread. On the
side of the tyre are the letters TWI (Tread Wear
Indicator). When the tyre's tread depth is down
to 1.6 mm, the tread depth will be level in height
with the tread wear indicators. Change to new
tyres as soon as possible. Remember that
NOTE
The legal provisions for the use of studded
tyres vary from country to country.
07
Tread depth
Road conditions with ice, slush and low temperatures place considerably higher demands
on tyres than summer conditions. It is therefore
recommended not to drive on winter tyres that
have a tread depth of less than four millimetres.
``
175
07 Wheels and tyres
General
Snow chains
Summer and winter wheels
adversely affected. Tyres with the greatest
tread depth should always be fitted to the rear
of the car (to decrease the risk of skidding).
Snow chains may only be used on the front
wheels. This also applies to all-wheel-drive
cars.
Volvo recommends that you contact an authorised Volvo workshop for checking if you are
uncertain about tread depth.
Never drive faster than 50 km/h with snow
chains. Avoid driving on bare ground as this
wears out both the snow chains and tyres.
Check that the snow chain does not make contact anywhere and that it is correctly fitted and
well tensioned.
Use Volvo genuine snow chains or equivalent chains designed for the car model, and
tyre and rim dimensions. In the event of
uncertainty Volvo recommends that you
consult an authorised Volvo workshop. The
wrong snow chains may cause serious
damage to your car and lead to an accident.
07
176
G020325
WARNING
The arrow shows the tyre's direction of rotation
When summer and winter wheels are changed,
see page 182, the wheels should be marked
with which side of the car they were mounted
on, for example L for left and R for right. Tyres
with a tread pattern which are designed to only
turn in one direction have the direction of rotation marked with an arrow. The tyre must
always rotate in the same direction throughout
its lifespan. Tyres should only be switched
between front and rear positions, never
between left and right-hand sides, or vice
versa. If the tyre is mounted incorrectly, the
car's braking characteristics and capacity to
force rain, snow and slush out of the way are
07 Wheels and tyres
Tyre pressure
Recommended tyre pressure
Stated on the decal:
• Tyre pressures for the car's recommended
tyre size
• ECO pressure1
• Spare wheel tyre pressure (Temporary
Spare).
Checking the tyre pressure
Check the tyre pressure regularly.
G020791
NOTE
The tyre pressure label on the driver's side door
pillar shows which pressures the tyres should
have at different loads and speed conditions.
Tyre pressure decreases over time, this is a
natural phenomenon. Tyre pressure also
varies depending on ambient temperature.
Even after several kilometres of driving, the
tyres warm up and the pressure increases. So
air must not be released if the pressure is
checked when the tyres are warm. While the
pressure must be increased if it is too low.
Inadequately inflated tyres increase fuel consumption, shorten tyre lifespan and impair the
car's roadholding. Driving on tyres with tyre
pressure that is too low can also result in the
tyres overheating and disintegrating.
For information on the correct tyre pressure,
see page 178. The specified tyre pressures
refer to "cold tyres". ("Cold tyres" means the
tyres are the same temperature as the ambient
temperature.)
Fuel economy, ECO pressure
At speeds under 160 km/h, the general tyre
pressure for full load is recommended in order
to obtain optimum fuel economy.
Tyre pressure affects travelling comfort, road
noise and steering characteristics.
07
1
ECO pressure results in improved fuel economy.
``
177
07 Wheels and tyres
Tyre pressure
Tyre pressure table
Variant
All
Tyre size
07
178
Load, 1-3 persons
Max. load
ECO pressureB
Front (kPa)
Rear
(kPa)
Front (kPa)
Rear (kPa)
235/65R17
0-160
220
220
270
270
270
235/60R18
160+
220
220
270
270
-
255/50R19
0-160
240
240
270
270
270
255/45R20
160 +
240
240
270
270
-
0-80
420
420
420
420
-
Temporary Spare Tyre
A
B
Speed
(km/h)A
In certain countries there is the "bar" unit beside the SI unit "Pascal": 1 bar = 100 kPa (270 kPa = 2.70 bar).
Economical driving, see page 177.
07 Wheels and tyres
Warning triangle* and spare wheel *
Warning triangle
After use:
Pack everything in reverse order.
Make sure that the warning triangle with case
is securely fastened in the compartment.
G027065
Spare wheel Temporary Spare*
Follow the regulations in force for the use of a
warning triangle* in the country in which you
are driving.
Use the warning triangle as follows:
1. Detach the warning triangle case. It is held
in place with a Velcro strap.
2. Remove the warning triangle from its case
(A).
3. Fold out the four support legs on the warning triangle.
4. Fold out both red sides of the warning triangle. Position the warning triangle in a
suitable place with regard to traffic.
The spare wheel (Temporary spare) is only
intended for use temporarily and must be
replaced by an ordinary wheel as soon as possible. The car's handling may be altered by the
use of the spare wheel. The spare wheel is
smaller than the normal wheel. The car's
ground clearance is affected accordingly. Pay
attention to high kerbs and do not machine
wash the car. If the spare wheel is fitted on the
front axle, you cannot use snow chains at the
same time. On all-wheel drive cars the drive on
the rear axle can be disconnected. The spare
wheel must not be repaired. The correct tyre
pressure for the spare wheel is stated in the
tyre pressure table, see page 178.
IMPORTANT
07
Never drive faster than 80 km/h with a spare
wheel on the car.
IMPORTANT
The car must never be driven fitted with
more than one "Temporary Spare" wheel.
``
* Option/accessory, for more information, see Introduction.
179
07 Wheels and tyres
Warning triangle* and spare wheel *
G026998
Spare wheel – removing
The spare wheel is located under the car. The
jack*, tool kit* and crank are located under the
floor hatch. The crank is in two parts. One part
is in the tool kit, and the other is under the tool
kit.
NOTE
07
There is a puller spanner in the tool kit to
remove the hub cap (certain wheel options).
Proceed as follows to release the spare wheel:
1. Lower the bottom of the tailgate and lift up
the floor hatch in the cargo area.
2. Take the two parts of the crank and assemble.
3. Fit the crank in the winch.
4. Loosen the tyre by cranking anticlockwise
until you reach the stop.
The location of the jack varies:
Cars seating seven
Cars seating five
180
* Option/accessory, for more information, see Introduction.
NOTE
The cable could damage the car if it hangs
free while driving.
5. Release the wheel from the cable and wind
up the cable clockwise.
6. Place the punctured tyre in the cargo area.
The tool kit contains a plastic bag for the
tyre.
07 Wheels and tyres
Warning triangle* and spare wheel *
NOTE
The spot under the car is only intended for
the car's original spare wheel. Do not place
any other wheels there.
Spare wheel – refitting
It is best to have two people put the spare
wheel back in place. One person to crank and
the other to guide the wheel.
1. Crank out the cable and place its anchor in
the centre hole of the wheel.
2. Slowly crank (clockwise) the cable in a bit.
3. Angle the wheel so that it comes in over the
exhaust system.
4. Hold down the rear edge of the wheel while
cranking it in.
5. Place the wheel above the rear axle,
against the floor.
WARNING
Check that the right mounting points are
being used. A production anchorage with
pin is located between the jacking points.
This is not strong enough to use to lift the
car. If you are unsure about the location of
the jacking points, Volvo recommends that
you contact an authorised Volvo workshop.
An incorrectly fitted jack could damage the
door and body.
Tools - returning into place
The tools and jack* must be returned to their
correct places after use. The jack must be
cranked to the correct position, see the preceding illustration, in order to have space.
IMPORTANT
The tools and jack* must be stored in the
intended location in the car's cargo area
when not in use.
6. Crank to the stop point.
7. Check that the wheel is properly secured.
First aid*
07
A case with first aid equipment is located in the
cargo area.
* Option/accessory, for more information, see Introduction.
181
07 Wheels and tyres
Changing wheels
Removing wheels
WARNING
Check that the jack is not damaged, that the
threads are thoroughly lubricated and that it
is free from dirt.
NOTE
G026997
Volvo recommends only using the jack* that
belongs to the car model in question, which
is indicated on the jack's label.
Remember to set out the warning triangle if you
must change a wheel in a trafficked area. There
are two jacking points on each side of the car.
The jacking points are centred under the bottom of the doors.
The label also indicates the jack's maximum
lift capacity at a specified minimum lifting
height.
3. Take out the jack*, wheel brace and crank,
see location see page 180. If another jack
is selected, see page 199.
1. Park the car on an even, firm surface with
no incline.
07
182
2. Apply the parking brake and engage
reverse gear (manual gearbox) or move the
gear selector to the P position (automatic
gearbox). Place chocks in front of and
behind the wheels which will remain on the
ground. Use stones or wooden blocks for
example.
* Option/accessory, for more information, see Introduction.
WARNING
Never crawl under the car when it is raised
on the jack. The car could fall, causing injuries.
The car's original jack should only be used
when changing wheels. All other work on
the car should be done using workshop
jacks and axle stands under the part of the
car that is raised.
The jack screw should be kept well lubricated.
If the surface is too soft, the jack could slide
to the side and the car could fall. No one
should be in the car when the wheel is being
changed.
4. Use the wheel brace to loosen the wheel
bolts ½-1 turn. Turn anticlockwise.
07 Wheels and tyres
Changing wheels
WARNING
Never position anything between the
ground and the jack, nor between the jacking point and the jack.
WARNING
G020332
If the jack is positioned incorrectly, the car
could fall. Risk of injury.
5. Place the jack under the jacking point and
crank it up towards the car floor. There is
an recess in the plastic cover at each
anchorage point. Check that the jack sits
securely in the anchorage. Then adjust the
jack so that its foot is positioned vertically
under the anchorage. See illustration.
IMPORTANT
The ground must be firm, smooth and level.
6. Lift the car until the wheel is free.
1. Clean the contract surfaces on the wheel
and hub.
2. Put on the wheel. Screw in the wheel bolts.
3. Lower the car so that the wheel cannot
rotate.
4. Tighten the wheel bolts alternately and in
torque steps. Tightening torque: 140 Nm
(14.0 kpm). It is important that they are
tightened to the correct torque. Check with
a torque wrench.
5. Screw the jack all the way down before
returning it to the cargo area. Then secure
it in place.
6. Check that the new tyre has the correct
amount of pressure.
NOTE
This wheel bolt may also be used for steel
wheel rims.
Make sure to use the correct type of bolt. Volvo
recommends that you contact the nearest
Volvo workshop if you are in any doubt.
07
G027000
7. Remove the wheel bolts and lift off the
wheel.
Fitting the wheel
183
07 Wheels and tyres
Emergency puncture repair*
General
The emergency puncture repair kit is used to
seal a puncture as well as to check and adjust
the tyre pressure. It consists of a compressor
and a bottle with sealing fluid. The kit works as
a temporary repair. The sealing fluid bottle
must be replaced before its expiration date and
after use.
The sealing fluid effectively seals tyres punctured in the tread.
the electrical socket that is nearest the punctured tyre.
Overview
WARNING
You should not drive faster than 80 km/h
after the emergency tyre repair kit has been
used. Volvo recommends that you visit an
authorised Volvo workshop for inspection of
the sealed tyre (maximum driving distance
is 200 km). The staff there can determine
whether or not the tyre can be repaired or if
it needs to be replaced.
NOTE
The jack is an option on cars equipped with
emergency puncture repair kit.
07
184
G020400
NOTE
The emergency puncture repair kit is only
intended for sealing tyres with a puncture in
the tread.
Taking out the emergency puncture
repair kit
The emergency puncture repair kit, with compressor and tools, is located under the floor in
the cargo area.
Label, maximum permitted speed
1. Fold away the rear edge of the floor mat,
forward from the back.
Cable
2. Lift up the emergency puncture repair kit.
Bottle holder (orange cap)
Switch
The emergency puncture repair kit has limited
capacity to seal tyres which have punctures in
the wall. Do not seal tyres with the emergency
puncture repair kit if they have larger slits,
cracks or similar damage.
Protective cap
12 V sockets for connecting the compressor
are located by the centre console in the front,
by the rear seat and in the cargo area. Choose
Sealing fluid bottle
* Option/accessory, for more information, see Introduction.
Pressure reducing valve
Air hose
Pressure gauge
07 Wheels and tyres
Emergency puncture repair*
Sealing punctured tyres
3. Check that the switch is in position 0 and
locate the cable and the air hose.
NOTE
Do not break the bottle's seal before use.
The seal is broken automatically when the
bottle is screwed in.
4. Unscrew the orange cap and unscrew the
bottle's stopper.
G019723
WARNING
For information on the function of the parts, see
preceding illustration.
1. Open the lid of the emergency puncture
repair kit.
2. Detach the decal for maximum permitted
speed and affix it to the steering wheel.
WARNING
The sealing fluid can irritate the skin. In the
case of contact with skin, wash away the
fluid with soap and water.
Do not unscrew the bottle, it is equipped
with a reverse catch to prevent leakage.
WARNING
Never stand next to the tyre when the compressor is running. If cracks or unevenness
arise then the compressor must be
switched off immediately. The journey
should not be continued. Contacting an
authorised tyre centre is recommended.
NOTE
When the compressor starts, the pressure
can increase up to 6 bar but the pressure
drops after approximately 30 seconds.
8. Flick the switch to position I.
IMPORTANT
5. Screw the bottle into its holder.
6. Unscrew the wheel's dust cap and screw
in the air hose valve connection to the bottom of the thread on the tyre's air valve.
Risk of overheating. The compressor must
not run for more than 10 minutes.
9. Inflate the tyre for 7 minutes.
WARNING
Do not leave children in the car without
supervision when the engine is running.
7. Plug the cable into the 12 V socket and
start the car.
WARNING
07
If the pressure is below 1.8 bar then the hole
in the tyre is too big. The journey should not
be continued. Contacting an authorised tyre
centre is recommended.
``
* Option/accessory, for more information, see Introduction.
185
07 Wheels and tyres
Emergency puncture repair*
10. Switch off the compressor to check the
pressure on the pressure gauge. Minimum
pressure is 1.8 bar and
maximum is 3.5 bar.
11. Switch off the compressor and unplug the
cable from the 12 V socket.
WARNING
Do not unscrew the bottle, it is equipped
with a reverse catch to prevent leakage.
5. Switch off the compressor. Detach the air
hose and cable. Refit the dust cap.
12. Detach the hose from the tyre valve and fit
the valve cap.
13. As soon as possible, drive
approximately 3 km at a maximum speed
of 80 km/h so that the sealing fluid can seal
the tyre.
NOTE
The sealing fluid bottle and the hose must
be replaced after use. Volvo recommends
that this replacement is performed by an
authorised Volvo workshop.
Rechecking the repair and pressure
WARNING
1. Reconnect the equipment.
2. Read the tyre pressure on the pressure
gauge.
3. If it is below 1.3 bar then the tyre is insufficiently sealed. The journey should not be
continued. Contact a tyre centre.
07
186
4. If the tyre pressure is higher than 1.3 bar
then the tyre must be inflated to the pressure specified on the tyre pressure label.
Release air using the pressure reducing
valve if the tyre pressure is too high.
Check the tyre pressure regularly.
6. Return the emergency puncture repair kit
to the cargo area.
7. Volvo recommends that you drive to the
nearest authorised Volvo workshop for the
replacement/repair of the damaged tyre.
Advise the workshop that the tyre contains
sealing fluid.
* Option/accessory, for more information, see Introduction.
WARNING
You should not drive faster than 80 km/h
after the emergency tyre repair kit has been
used. Volvo recommends that you visit an
authorised Volvo workshop for inspection of
the sealed tyre (maximum driving distance
is 200 km). The staff there can determine
whether or not the tyre can be repaired or if
it needs to be replaced.
Inflating the tyres
The car's original tyres can be inflated by the
compressor.
1. The compressor must be switched off.
Make sure that the switch is in position 0
and locate the cable and air hose.
2. Unscrew the wheel's dust cap and screw
in the air hose valve connection to the bottom of the thread on the tyre's air valve.
WARNING
Do not leave children in the car without
supervision when the engine is running.
07 Wheels and tyres
Emergency puncture repair*
WARNING
Inhaling car exhaust fumes can result in
danger to life. Never leave the engine running in sealed areas or areas that lack sufficient ventilation.
Changing the sealing fluid canister
Replace the bottle when the expiration date
has passed. Treat the old bottle as environmentally hazardous waste.
WARNING
3. Connect the cable to one of the car's 12 V
sockets and start the car.
The bottle contains 1.2-Ethanol and natural
rubber-latex.
4. Start the compressor by flicking the switch
to position I.
Harmful if ingested. Could result in allergic
reaction in the event of skin contact.
Avoid contact with the skin and eyes.
IMPORTANT
Risk of overheating. The compressor must
not run for more than 10 minutes.
5. Inflate the tyre to the pressure specified on
the tyre pressure decal. (Release air using
the pressure reducing valve if the tyre pressure is too high.)
Store out of the reach of children.
NOTE
Leave the container at a collection point for
storing dangerous waste.
6. Switch off the compressor. Detach the air
hose and cable.
7. Refit the dust cap.
07
* Option/accessory, for more information, see Introduction.
187
Cleaning................................................................................................ 190
Touching up paintwork ........................................................................ 194
Rustproofing......................................................................................... 195
188
CAR CARE
08 Car care
Cleaning
Washing the car
Wash the car as soon as it becomes dirty. Use
car shampoo. Dirt and road salt can lead to
corrosion.
• Do not park the car in direct sunlight.
Washing a car with hot paintwork can
cause permanent paintwork damage.
Wash the car in a car wash with waste
water separator.
• Hose down the underbody thoroughly.
• Wash using a sponge, car shampoo and
plenty of lukewarm water.
NOTE
Outside lighting such as headlamps, fog
lamps and rear lamps may temporarily have
condensation on the inside of the lens. This
is a natural phenomenon, all outside lighting
is designed to withstand this. Condensation
is normally vented out of the lamp when it
has been switched on for a time.
Cleaning the wiper blades
Asphalt, dust and salt residue on wiper blades,
as well as insects, ice etc. on the windscreen,
impair the service life of wiper blades.
• If the dirt is difficult to dislodge, wash the
car using a cold degreasing agent.
• Dry the car using a clean, soft chamois or
a water scraper.
WARNING
Always have the engine cleaned by a workshop. There is a risk of fire if the engine is
hot.
IMPORTANT
Dirty headlamps have impaired functionality. Clean them regularly, when refuelling for
example.
08
190
NOTE
Wash the wiper blades and windscreen regularly with lukewarm soap solution or car
shampoo.
Do not use any strong solvents.
Removing bird droppings
Wash away bird droppings from the paintwork
as soon as possible. Bird droppings contain
chemicals that affect and discolour paintwork
very quickly. This discoloration can only be
removed by a specialist.
Chromed wheels
IMPORTANT
Rim cleaning agents can cause stains on
chrome-plated wheels. Wash using a
sponge, car shampoo and plenty of lukewarm water.
Automatic car washes
An automatic car wash is a simple and quick
way of washing the car, but it can never replace
a proper handwashing. The brushes of an automatic car wash cannot reach everywhere.
IMPORTANT
Washing by hand is gentler to the paintwork
than an automatic car wash. Paintwork is
also more sensitive when it is new. For this
reason, handwashing is recommended during the first few months with a new car.
High-pressure washing
When using high-pressure washing, use
sweeping movements and make sure that the
nozzle does not come closer than 30 cm to the
surface of the car (the distance applies to all
exterior parts).
08 Car care
Cleaning
IMPORTANT
Rinse the entire car to remove loose dirt.
When using a pressure washer: Make sure
that the nozzle of the pressure washer is not
closer than 30 cm to the bodywork. Do not
spray directly onto the locks.
Testing the brakes
WARNING
Always test the brakes after washing the
car, including the parking brake, to ensure
that moisture and corrosion do not attack
the brake linings and reduce braking performance.
Lightly depress the brake pedal now and then
when driving long distances in rain or slush.
This heats and dries the brake pads. Do the
same thing after starting in very damp or cold
weather.
Exterior plastic, rubber and trim
components
A special cleaning agent available from Volvo
dealers is recommended for the cleaning and
care of coloured plastic parts, rubber and trim
components (such as glossy trim mouldings).
When using such a cleaning agent the instructions must be followed carefully.
IMPORTANT
IMPORTANT
Avoid waxing and polishing on plastic and
rubber.
When using degreasant on plastic and rubber, only rub with light pressure if it is necessary. Use a soft washing sponge.
Polishing glossy trim mouldings could wear
away or damage the glossy surface.
Polishing agent that contains abrasive must
not be used.
Polishing and waxing
Polish and wax the car if the paintwork is dull
or to give the paintwork extra protection.
The car does not need to be polished until it is
at least one year old. However, the car can be
waxed before this time. Do not polish or wax
the car in direct sunlight.
Wash and dry the car thoroughly before you
begin polishing or waxing. Clean off asphalt
and tar stains using tar remover or white spirit.
More stubborn stains can be removed using
fine rubbing paste designed for car paintwork.
Polish first with a polish and then wax with liquid or solid wax. Follow the instructions on the
packaging carefully. Many preparations contain both polish and wax.
Only paint treatment recommended by
Volvo should be used. Other treatment such
as preserving, sealing, protection, lustre
sealing or similar could damage the paintwork. Paintwork damage caused by such
treatments is not covered by Volvo warranty.
Water-repellent coating*
Never use products such as car wax,
degreaser or similar on glass surfaces as this could ruin their water-repellent
properties.
Take care when cleaning so as not to damage
the glass surface.
To avoid damaging glass surfaces when
removing ice – only use plastic ice scrapers.
There is natural wear of the water-repellent
coating.
NOTE
Treatment with a special finishing agent
available from Volvo dealers is recommended in order to maintain the waterrepellent properties. This should be used
first after three years and then each year.
08
``
* Option/accessory, for more information, see Introduction.
191
08 Car care
Cleaning
Cleaning the interior
Treatment of stains on textile upholstery
and headliner
Only use cleaning agents and car care products recommended by Volvo. Clean regularly
and follow the instructions included with the
car care product. Other chemicals can impair
the fire retardant qualities of the upholstery.
Vacuuming is important prior to using cleaning
agents.
Volvo's cleaning agents can also be used for
stains on the mat after vacuuming.
IMPORTANT
Sharp objects and Velcro may damage the
fabric upholstery.
A special fabric cleaning agent, available from
authorised Volvo dealers, is recommended to
avoid impairing the fire retardant qualities of
the upholstery. Use water and a synthetic
detergent to clean the seatbelts. Make sure the
seatbelt is dry before allowing it to retract.
Treating stains on leather upholstery
08
192
Volvo's leather upholstery is chromium-free
and approved in accordance with the OekoTex 100 standard and is treated to preserve its
original appearance.
Leather upholstery ages and acquires a beautiful patina over time. The leather is refined and
processed so that it retains its natural characteristics. It is given a protective coating, but
regular cleaning is required in order to maintain
both characteristics and appearance. Volvo
offers a comprehensive product for the cleaning and treatment of leather upholstery which,
when used in accordance with the instructions,
preserves the leather's protective coating.
After a period of use the natural appearance of
the leather will nevertheless emerge, depending more or less on the surface texture of the
leather. This is a natural maturing of the leather
and shows that it is a natural product.
Washing instructions for leather
upholstery
To achieve best results Volvo recommends
cleaning and the application of protective
cream once to four times per year (or more if
necessary). The Volvo Leather Care kit is available from your Volvo dealer.
Vacuuming is important prior to using leather
care agents.
IMPORTANT
•
Certain items of coloured clothing (for
example, jeans and suede garments)
may stain the upholstery.
•
Never use strong solvents. Such products may damage fabric, vinyl and
leather upholstery.
1. Pour the leather cleaner on the dampened
sponge and squeeze out a strong foam.
2. Work the dirt away with gentle circular
movements.
3. Dab accurately with the sponge on the
stains. Allow the sponge to absorb the
stain. Do not rub.
4. Wipe off with soft paper or a cloth and
allow the leather to dry completely.
Protective treatment of leather
upholstery
1. Pour a small amount of the protective
cream on the felted cloth and massage in
a thin layer of cream with gentle circular
movements on the leather.
2. Allow the leather to dry for 20 minutes
before use.
The leather has now been given improved protection against stains and improved UV protection.
08 Car care
Cleaning
IMPORTANT
Sharp objects may damage the leather, (e.g.
rings).
Washing instructions for the leather
steering wheel
• Remove dirt and dust with a soft pre-moistened sponge and neutral soap.
• Leather needs to breathe. Never cover the
leather steering wheel with protective plastic.
Treating stains on interior plastic, metal
and wood parts
A special cleaning agent, available from Volvo
dealers, is recommended for cleaning interior
parts and surfaces. Do not scrape or rub stains.
Never use strong stain removers.
Cleaning seatbelts
Use water and a synthetic detergent. A special
textile cleaning agent is available from your
Volvo dealer. Make sure the seatbelt is dry
before allowing it to retract.
• Use natural oils. Volvo's leather care
agents are recommended for best results.
If the steering wheel has stains:
Group 1 (ink, wine, coffee, milk, sweat and
blood)
Use a soft cloth or sponge. Mix a 5%
ammonia solution. (For blood stains, use a
solution of 2 dl water and 25g salt.)
Group 2 (fats, oils, sauces and chocolate)
1. Same procedure as group I.
2. Polish with an absorbent paper or cloth.
Group 3 (dry dirt, dust)
1. Use a soft brush to remove the dirt.
08
2. Same procedure as group I.
193
08 Car care
Touching up paintwork
Paintwork
Stone chips and scratches
If the stone chip has penetrated to the
bare metal
Paint is an important part of the car's rustproofing and should therefore be checked regularly. To avoid the onset of rust, damaged
paintwork should be rectified immediately. The
most common types of paintwork damage are
stone chips, scratches, and marks on the
edges of wings and doors.
1. Apply a piece of masking tape over the
damaged surface. Then remove the tape to
remove any loose paint.
2. Stir the primer well and apply using a fine
brush or a matchstick. Apply paint using a
brush once the primer is dry.
Colour code
G020345
3. For scratches, proceed as above, but
mask around the damaged area to protect
the undamaged paintwork.
Before touching up paintwork, the car must be
clean and dry and at a temperature above
15 °C.
Materials
Data plate.
Code for car colour
It is important that the correct colour is used.
For product decal location, see page 272.
08
1
194
• Primer in a can
• Spray can or touch-up pen1
• Masking tape.
Minor stone chips and scratches
If the stone chip has not penetrated to the bare
metal and there is an undamaged colour coat,
you can paint straight after cleaning the damaged area.
Follow the instructions contained in the touch-up pen's packaging.
4. After a few days, polish the touched-up
areas. Use a soft rag and a small amount
of lapping paste.
08 Car care
Rustproofing
Inspection and maintenance
Your car has already received a thorough and
complete rustproofing at the factory. Parts of
the body are made of galvanised sheet metal.
The underbody is protected by a wear-resistant anti-corrosion compound. A thin, penetrating rustproofing fluid was sprayed into the
members, cavities and closed sections.
Maintain the car's rustproofing.
• Keep the car clean. Hose down the underbody. If using a pressure washer, keep the
nozzle at least 30 cm from the painted surfaces.
• Regularly check and touch-up the rustproofing treatment as necessary.
The car's rustproofing does not normally
require treatment for approximately 12 years.
After this period, it should be treated at threeyear intervals. If the car needs further treatment, Volvo recommends that you engage an
authorised Volvo workshop for assistance.
08
195
Volvo service.........................................................................................
Self-maintenance..................................................................................
Bonnet and engine compartment.........................................................
Oils and fluids.......................................................................................
Wiper blades.........................................................................................
Battery...................................................................................................
Replacing bulbs ...................................................................................
Fuses.....................................................................................................
196
198
199
201
203
207
209
211
218
MAINTENANCE AND SERVICE
09 Maintenance and service
09
Volvo service
Volvo service programme
Before the car left the factory, it was thoroughly
test driven. It was checked again in accordance with Volvo Car Corporation regulations
before it was handed over to you.
To keep your Volvo as safe and reliable as possible, follow the Volvo service programme
specified in the Service and Warranty Booklet.
Volvo also recommends that you engage an
authorised Volvo workshop to perform the
service and maintenance work. Volvo workshops have the personnel, special tools and
service literature to guarantee the highest quality of service.
IMPORTANT
For the Volvo warranty to apply, check and
follow the instructions in the Service and
Warranty Booklet.
Special service measures
Certain service measures which affect the car's
electrical system can only be performed using
electronic equipment specially developed for
your car. Similarly, Volvo recommends that you
contact an authorised Volvo workshop before
starting or performing service work that affects
the electrical system.
198
09 Maintenance and service
Self-maintenance
Before starting work on the car
Check regularly
Battery
Check the following at regular intervals, for
example, when refuelling:
Never disconnect the battery when the engine
is running (e.g. if replacing the battery).
Never use a quick charger to charge the battery. The battery cables must be disconnected
when charging the battery.
The battery contains acid that is both corrosive
and toxic. It is therefore important to handle the
battery in an environmentally correct manner.
Let your Volvo dealer assist you.
Lifting the car
• Coolant – The level must be between the
MIN and MAX marks on the expansion
tank.
• Engine oil – The level must be between the
MIN and MAX marks.
• Power steering fluid – The level must be
between the MIN and MAX marks.
• Washer fluid – The reservoir should be well
filled. Use washer antifreeze at temperatures around freezing.
G027001
Check that the battery cables are correctly
connected and tightened.
09
• Brake and clutch fluid – The level must be
between the MIN and MAX marks.
WARNING
High output from the ignition system. The
voltage in the ignition system is highly dangerous. The ignition must therefore always
be switched off for work in the engine compartment.
Do not touch the spark plugs or ignition coils
when the ignition is on or the engine is hot.
WARNING
Bear in mind that the radiator fan may start
automatically some time after the engine
has been switched off.
Always have the engine cleaned by a workshop. There is a risk of fire if the engine is
hot.
NOTE
Volvo recommends only using the jack that
belongs to the car model in question. If a
jack other than one recommended by Volvo
is selected, then follow the instructions
included with the equipment
If the car is lifted with a workshop jack; position
the jack with the front edge on the subframe.
Do not damage the splashguard under the
engine. Ensure that the jack is positioned so
that the car cannot slide off the jack. Always
use axle stands or the like.
``
199
09 Maintenance and service
09
Self-maintenance
If you lift the car using a two pillar workshop lift,
ensure that the front and rear lift arms are fixed
under the lifting points on the door sill. See
previous illustration.
200
09 Maintenance and service
Bonnet and engine compartment
Opening the bonnet
09
WARNING
G026995
Close the bonnet by placing your hand on
its top and pressing down. Do not close it
by holding the grille. Engine components on
the inside could injure your fingers.
1. Pull the handle on the far left (or right if the
car is RHD) under the instrument panel.
You will hear when the lock releases.
2. Insert your hand to the right under the front
edge of the bonnet (below the grille).
3. Press up the safety catch handle.
4. Release the handle and open the bonnet.
WARNING
Check that the bonnet locks properly when
closed.
``
201
09 Maintenance and service
09
Bonnet and engine compartment
G027074
Engine compartment
Clutch and brake fluid reservoir
Chassis data plate
Relay and fuses
Battery (in cargo area)
Air filter. (The cover has a different design
depending on engine variant.)
Radiator
Engine oil dipstick
Engine oil filling
Washer fluid reservoir
Power steering fluid reservoir
Expansion tank, cooling system
202
09 Maintenance and service
Oils and fluids
Engine compartment decal for oil
grade.
Checking the engine oil and oil filter
Volvo recommends Castrol oil products.
Change the oil and oil filter in accordance with
the intervals specified in the Service and Warranty Booklet.
IMPORTANT
In order to fulfil the requirements for the
engine's service intervals all engines are
filled with a specially adapted synthetic
engine oil at the factory. The choice of oil
has been made very carefully with regard to
service life, starting characteristics, fuel
consumption and environmental impact.
Using oil of a higher than specified grade is
permitted. If the car is driven in adverse conditions, Volvo recommends using an oil of a
higher grade than that specified on the decal,
see page 277.
An approved engine oil must be used in
order that the recommended service intervals can be applied. Only use a prescribed
grade of oil (see the engine compartment
decal) for both filling and oil change, otherwise you will risk affecting service life, starting characteristics, fuel consumption and
environmental impact.
09
via the warning symbol in the centre of the
instrument unit as well as by display texts. Certain models have both variants. Volvo recommends that you contact an authorised Volvo
dealer for more information.
Checking the oil level in a new car is especially
important before the first scheduled oil change.
The Service and Warranty Booklet specifies the
odometer readings for oil changes.
Volvo recommends checking the oil level every
2 500 km. The most accurate measurements
are made on a cold engine before starting. The
measurement will be inaccurate if taken immediately after the engine is switched off. The
dipstick will indicate that the level is too low
because the oil has not had time to flow down
into the oil sump.
Volvo Car Corporation disclaims all warranty liability if engine oil of the prescribed
grade and viscosity is not used.
Volvo uses different systems for warning of low
oil level or low oil pressure. Certain variants
have an oil pressure sensor, and then the lamp
for oil pressure is used. Other variants have an
oil level sensor, and then the driver is informed
``
203
09 Maintenance and service
09
Oils and fluids
Checking the oil
Checking the oil in a warm engine
Washer fluid, filling
1. Park the car on a level surface, switch off
the engine and wait 10 – 15 minutes to
allow the oil time to run back to the sump.
2. Wipe the dipstick clean before checking
the level.
The oil level must be within the area marked on the
dipstick.
Checking the oil in a cold engine
1. Wipe the dipstick clean before checking
the level.
2. Check the oil level using the dipstick. The
level must be between the MIN and MAX
marks.
3. If the level is close to the MIN mark, start
by topping up with 0.5 litres. Top up until
the oil level is nearer the MAX than the
MIN mark on the dipstick, see page 277
and forward for capacities.
204
If the level is close to the MIN mark, start by
topping up with 0.5 litres. Top up until the oil
level is nearer the MAX than the MIN mark on
the dipstick, see page 277 and forward for
capacities.
G027097
G020336
3. Check the oil level using the dipstick. The
level must be between the MIN and MAX
marks.
Location of washer fluid reservoir.
WARNING
Do not spill oil onto the hot exhaust manifold
due to the risk of fire.
IMPORTANT
Never fill above the MAX mark. Oil consumption may increase if too much oil is
poured into the engine.
The windscreen and headlamp washers have
the same reservoir. Add antifreeze in the winter
so that the fluid does not freeze in the pump,
reservoir and hoses. See capacities on page
279 .
NOTE
TIP! Clean the wiper blades when topping
up washer fluid. Mix the washer antifreeze
and water before filling the reservoir.
09 Maintenance and service
Oils and fluids
Checking and topping up the coolant
See capacities on page 279 .
G027087
When topping up the coolant, follow the
instructions on the packaging. It is important
that the mixture of coolant concentrate and
water is correct for the prevailing weather conditions. Never top up with water only. The risk
of freezing increases with both too little and too
much coolant concentrate.
IMPORTANT
Always use coolant with anti-corrosion
agent as recommended by Volvo. New cars
are filled with coolant that can withstand
temperatures down to approximately
ca -35 °C.
IMPORTANT
Check the coolant regularly
•
The level must lie between the MIN and MAX
marks on the expansion tank. If the system is
not filled sufficiently, high local temperatures
could occur, causing a risk of damage (cracks)
to the cylinder head. Top up the coolant when
the level falls to the MIN mark.
A high content of chlorine, chlorides
and other salts may cause corrosion in
the cooling system.
•
Always use coolant with anti-corrosion
agent as recommended by Volvo.
•
Ensure that the coolant mixture is 50%
water and 50% coolant.
•
Mix the coolant with approved quality
tap water. In the event of any doubt
about water quality, used ready-mixed
coolant in accordance with Volvo recommendations.
•
When changing coolant/replacing cooling system components, flush the cooling system clean with approved quality
tap water or flush with ready-mixed
coolant.
•
The engine must only be run with a wellfilled cooling system. High temperatures may occur, causing a risk of damage (cracks) to the cylinder head.
WARNING
Coolant can be very hot. If the coolant
requires topping up when the engine is at
operating temperature, unscrew the expansion tank cap slowly to gently release the
overpressure.
09
For capacities and for standards regarding
water quality, see the table under Fluids and
lubricants on page 279 .
``
205
09 Maintenance and service
Oils and fluids
09
Checking and topping up the brake and
clutch fluid
WARNING
If the brake fluid is under the MIN level in the
brake fluid reservoir, do not drive further
before topping up the brake fluid.
The reason for the loss of brake fluid must
be investigated.
G000000
ADD
G026991
Brake and clutch fluid have a common reservoir1. The fluid level must be between the
MIN and MAX marks. Check the level regularly.
Change the brake fluid every other year or at
every other regular service.
See the capacities and recommended fluid
grade on page 279 .
The fluid should be changed annually on cars
driven in conditions requiring hard, frequent
braking, such as driving in mountains or tropical climates with high humidity.
1
206
Location dependent on whether car is left or right-hand drive.
NOTE
Check the level frequently.
NOTE
If a fault should arise in the power steering
system or if the car is without power and
must be towed, it can still be steered. However, the steering will be much heavier than
normal and it will require more effort to turn
the steering wheel.
Checking and topping up the power
steering fluid
FULL
Check the level frequently. The fluid does not
require changing. The level must lie between
the ADD and FULL marks. See the capacities
and recommended grade on page 279 .
09 Maintenance and service
Wiper blades
Cleaning
For cleaning wiper blades and windscreen, see
page 190.
IMPORTANT
Check the wiper blades regularly.
Neglected maintenance shortens the service life of the wiper blades.
Replacing the wiper blades, windscreen
NOTE
The wiper blades are different lengths. The
blade on the driver's side is longer than on
the other side.
1. Fold out the wiper arm and grasp the wiper
blade.
2. Press in the ribbed spring catch on the
wiper blade while lifting it off at the arm
extension.
3. Fit the new blade in reverse order and
check that it is properly secured.
Changing the rear window wiper blade
G026959
Wiper blades
09
1. Fold out the wiper arm.
``
207
09 Maintenance and service
09
Wiper blades
2. Remove the wiper blade by moving it up/
out (see illustration) towards the tailgate.
3. Press the new wiper blade into position.
4. Check that the blade is firmly installed.
208
09 Maintenance and service
Battery
Battery care
The service life and function of the battery is
influenced by factors such as the number of
starts, discharging, driving style, driving conditions and climatic conditions.
NOTE
An expended battery must be recycled in an
environmentally safe manner as it contains
lead.
WARNING
Batteries can generate oxyhydrogen gas,
which is highly explosive. One spark, which
can be generated if you connect the jump
leads incorrectly, is sufficient to make the
battery explode. The battery contains sulphuric acid, which can cause serious burns.
If the acid comes into contact with eyes,
skin or clothing, flush with large quantities
of water. If acid splashes into the eyes, seek
medical attention immediately.
NOTE
The life of the battery is shortened if it
becomes discharged repeatedly.
The life of the battery is affected by several
factors, including driving conditions and climate. Battery starting capacity decreases
gradually with time and therefore needs to
be recharged if the car is not used for a
longer time or when it is only driven short
distances. Extreme cold further limits starting capacity.
To maintain the battery in good condition, at
least 15minutes of driving/week is recommended or that the battery is connected to
a battery charger with automatic trickle
charging.
09
Further information in the
owner's manual.
Store the battery out of the
reach of children.
The battery contains corrosive acid.
A battery that is kept fully charged has a
maximum service life.
Symbols on the battery
Use protective goggles.
Avoid sparks and naked
flames.
Risk of explosion.
``
209
09 Maintenance and service
09
Battery
Changing the battery
Fitting the battery
Removing the battery
WARNING
REMOVAL OF BATTERY
DISCONNECT
O CABLE FIRST
xxxx xxxxx xx xxxxx
xxxx xxxxx xx xxxxx
xxxx xxxxx xxxxx
xxxx xx
-
G027075
DRAIN PIPE
1. Set the battery in place
1. Switch off the ignition and remove the
remote control key
2. Connect the positive lead
2. Unscrew the bracket and cover over the
battery
4. Make sure the evacuation hose is correctly
connected to both the battery and the outlet in the bodywork.
3. Wait at least 5 minutes before touching any
electrical terminals. (This allows time for
the information in your car's electrical system to be stored in the control modules.)
4. Disconnect the negative lead first
5. Then disconnect the positive lead and the
evacuation hose for the oxyhydrogen gas
210
G027076
+
3. Connect the negative lead
5. Refit the cover and bracket
09 Maintenance and service
Replacing bulbs
Changing front bulbs
IMPORTANT
All bulb specifications are given on page 284.
Do not pull the electrical cable, only the connector
The following list contains bulbs and pointsource lamps that are specialised or unsuitable
for changing except at a workshop:
5. Unplug the connector by first pressing in
the catch from underneath and then pulling
it up a bit from above.
• General interior lighting in the roof
• Reading lamps and glovebox lighting
• Indicator, door mirror and approach light-
6. Lift out the entire headlamp insert and
place it on a soft surface so as not to damage the lens.
ing
G027081
• High-level brake light
• Active Xenon headlamps
WARNING
On cars equipped with Xenon lamps, headlamp replacement must be performed at a
workshop - an authorised Volvo workshop
is recommended. The lamp must be handled with extreme caution because it is
equipped with a high voltage unit.
IMPORTANT
Never touch the glass part of the bulbs with
your fingers. Grease and oil from your fingers are vaporised by the heat, coating the
reflector and then causing damage.
The entire lamp insert must first be removed
when replacing dipped beam, main beam and
parking lamp bulbs. To replace one of these
bulbs, do the following and then consult the
instructions for the specific lamp.
Removing the lamp housing:
1. Switch off all lights and turn the remote
control key to position 0.
G027083
General
09
2. Open the bonnet.
3. Release the insert by pulling up the two
lock pins holding it in place.
Refit the headlamp insert in reverse order.
Check that the lock pins are correctly situated.
4. Lift the insert straight out.
``
211
09 Maintenance and service
09
Replacing bulbs
Location of bulbs in front lamp
Dipped beam, halogen
8. Screw the cover back into place; the marking HAUT should be at the top.
Main beam
Main beam
Direction indicator
Parking/position lamps
Side marker lamps
1. Undo the outer cover by turning it anticlockwise.
2. Unplug the connector.
3. Disconnect the spring clamp. First push to
the right so that the spring clamp disconnects, then out and down.
4. Pull out the lamp.
5. Fit the new bulb. It can only fit in one position.
6. Press the clamp spring upwards and a little
to the left so that it secures in its catch.
7. Press the connector back in place.
212
G027085
Dipped beam
G027088
G027082
Halogen headlamps
1. Undo the outer cover by pulling it straight
out and then unplug the connector.
2. Disconnect the spring clamp. First push to
the right so that the spring clamp disconnects, then out and down.
3. Pull out the lamp.
4. Fit the new bulb. It can only fit in one position.
09 Maintenance and service
Replacing bulbs
5. Press the clamp spring upwards and a little
to the left so that it secures in its catch.
4. Fit the bulb holder back in place and turn
clockwise.
6. Press the connector back in place and refit
the cover.
Direction indicators
09
Front fog lamps
G027089
G027078
Side marker lamps and position/
parking lamps
1. Switch off all lights and turn the remote
control key to position 0.
G028409
2. Turn the bulb holder slightly anticlockwise.
The bulbs are housed in bayonet holders.
1. Turn the bulb holder anticlockwise and
remove.
2. Pull the bulb straight out.
The bulbs are housed in bayonet holders.
1. Turn the bulb holder anticlockwise and
remove.
2. Press in the bulb, turn anticlockwise and
remove.
3. Fit the new bulb by pressing it into the
recess and then turning clockwise.
3. Remove the lamp.
4. Fit the new bulb. The profile of the bulb
holder matches the one on the foot of the
lamp.
5. Refit the bulb holder by turning slightly
clockwise. The TOP mark on the bulb
holder must be upward.
3. Fit the new bulb by carefully pressing it into
the recess.
``
213
09 Maintenance and service
09
Replacing bulbs
G027094
Bulbs in rear lamp cluster
Position lamps
Direction indicators
Reversing lamp
Position lamps
Brake light
NOTE
If an error message remains after a faulty
bulb has been replaced then we recommend that you visit an authorised Volvo
workshop.
214
09 Maintenance and service
Replacing bulbs
09
G027077
Bulb replacement
1. Switch off all lights and turn the remote
control key to position 0.
7. Loosen the extra length of cable for better
accessibility.
13. Refit the bulb holder in the recess and turn
clockwise.
2. Lower the bottom of the tailgate and open
the floor hatch. (If the car is equipped with
a grocery bag holder*, undo the holder's
retaining straps.)
8. Place the insert on a soft surface so as not
to scratch the glass.
14. Press back the extra length of cable.
3. Remove the corner piece.
9. Turn the bulb holder anticlockwise and pull
it out.
4. Open the hatch in the side panel by pulling
the catch up and towards you.
10. Turn the bulb anticlockwise to loosen it.
(Applies to direction indicators, reversing
lamps and brake lamps).
5. Take spanner no. 10 out of the tool kit and
undo the nuts.
11. Pull the bulb straight out. (Applies to position lamps).
6. Pull the entire insert straight back.
12. Replace the bulb.
15. Refit the insert against the bolt holes. Press
the insert into place.
16. Tighten the nuts.
17. Refit the side panel and corner piece.
``
215
09 Maintenance and service
Replacing bulbs
1. Insert a slotted screwdriver as indicated by
the arrow in the illustration.
1. Switch off all lights and turn the remote
control key to position 0.
There is courtesy lighting under the instrument
panel on the driver and passenger sides.
2. Prise out the lamp insert.
2. Remove the screws with a screwdriver.
3. Turn the bulb holder anticlockwise to
loosen it.
3. Loosen the whole lamp housing carefully
and pull it out.
1. Insert a screwdriver and gently turn so that
the lens detaches.
4. Turn the bulb anticlockwise and lift the
bulb out.
4. Replace the bulb.
3. Fit a new bulb.
5. Refit the entire lamp housing and screw it
into place.
4. Refit the lens.
5. Replace the bulb.
216
Courtesy lighting
G027079
Number plate lighting
G027093
Rear fog lamp
G027092
09
2. Remove the blown bulb.
09 Maintenance and service
Replacing bulbs
G027084
1. Insert a screwdriver and gently turn so that
the lamp housing comes loose.
2. Remove the blown bulb.
3. Fit a new bulb. Check that the bulb lights.
G027080
Vanity mirror lighting
Bulbs in the cargo area
4. Refit the lamp housing.
09
1. Insert a slotted screwdriver at the side of
the centre clip in the bottom edge of the
mirror. Lift up so the centre clip releases.
2. Slide the screwdriver from side to side so
that the outer clips release.
3. Lift out the mirror insert.
4. Replace the bulbs.
5. Refit the insert top edge first. Be sure that
the upper clips are properly depressed
before pressing the insert back.
217
09 Maintenance and service
09
Fuses
G032337
General
Cable routing may vary slightly due to engine variant. However, the components listed are in the same positions.
All electrical functions and components are
protected with a number of fuses to protect
your car's electrical system from damage by
short-circuits or overloads.
The fuses are in five different locations in the
car:
Fuse box in cargo area - Executive*
If an electrical component or function does not
work, this may be because the component's
fuse was temporarily overloaded and blew.
Relay/fuse box in the engine compartment.
1. Look in the fuse diagram to locate the fuse.
Fuse box in the passenger compartment
within the sound barrier on the driver's
side.
2. Pull out the fuse and check from the side
to see whether the curved wire has blown.
Fuse box in the passenger compartment at
dashboard end on driver's side.
218
Fuse box in cargo area.
3. If this is the case, replace it with a new fuse
of the same colour and amperage.
WARNING
Never use a foreign object, or a fuse with an
amperage higher than that specified when
replacing a fuse. This could cause significant damage to the electrical system and
possibly lead to fire.
There are a number of spare fuses in the cover
on the end face of the instrument panel. There
are also pliers which facilitate the removal and
fitting of fuses.
If the same fuse fails repeatedly then there is a
fault in the component. In which case, Volvo
09 Maintenance and service
Fuses
09
recommends that you visit an authorised Volvo
workshop for this to be checked.
``
219
09 Maintenance and service
09
Fuses
G026972
Relay/fuse box in the engine compartment
1.
220
ABS
30 A
2.
ABS
3.
High-pressure
washer, headlamps
35 A
4.
Parking heater*
25 A
5.
Auxiliary lamps*
20 A
6.
Starter motor relay
35 A
7.
Windscreen wipers
25 A
8.
Fuel pump
15 A
9.
30 A
10.
* Option/accessory, for more information, see Introduction.
11.
Transmission control
module (TCM)
Ignition coils (petrol),
engine control module
(ECM), injection
valves, (diesel)
Accelerator pedal
sensor (APM), AC
compressor
12.
15 A
20 A
10 A
Engine control module
(ECM) (petrol), injection valves (petrol),
mass air flow sensor
(petrol)
15 A
mass air flow sensor
(diesel)
5A
09 Maintenance and service
Fuses
13.
Electronic throttle
module (V8), VIS (6cyl. petrol)
10 A
Electronic throttle
module (ETM), solenoid valve, SWIRL (air
mixing valve), fuel
pressure regulator
(diesel)
15 A
Lambda-sond (petrol)
20 A
Lambda-sond (diesel)
10 A
Crankcase ventilation
heater (petrol), AC
connection (petrol),
solenoid valves, leakage diagnosis (petrol),
ECM, (petrol), mass air
flow sensor (V8), glow
heating control (diesel)
15 A
16.
Dipped beam, left
20 A
17.
Dipped beam, right
20 A
18.
-
19.
Engine control module
(ECM) supply, engine
relay
14.
15.
20.
Position lamps
15 A
21.
Vacuum pump (petrol)
20 A
09
-
5A
``
221
09 Maintenance and service
09
Fuses
G032316
Relay/fuse box in the passenger compartment at dashboard end on driver's side
A decal which specifies the positions and amperages of the fuses is located in the end box cover.
1.
Climate control system fan
30 A
2.
Audio (amplifier)*
30 A
3.
Power driver's seat*
25 A
4.
Power passenger
seat*
5.
6.
222
Control module, left
front door
Control module, right
front door
25 A
7.
-
8.
Radio, CD player, RSE
system*
15 A
RTI display, RTI unit
MMM
10 A
9.
10.
25 A
25 A
* Option/accessory, for more information, see Introduction.
OBDII, light switch
(LSM), Steering Angle
Sensor (SAS), Steering Wheel Module
(SWM)
-
11.
12.
5A
Ignition switch, SRSsystem, engine control module ECM (petrol) SRS deactivation
passenger side
(PACOS), electronic
immobiliser (IMMO),
Transmission control
module (TCM)
7.5 A
General lighting, ceiling (RCM) Upper electronic module (UEM)
10 A
09 Maintenance and service
Fuses
13.
Sunroof*
15 A
14.
Telephone*, Bluetooth*
5A
15-38
09
-
``
* Option/accessory, for more information, see Introduction.
223
09 Maintenance and service
09
Fuses
G028412
Relay/fuse box in the passenger compartment within the sound barrier on the driver's side
224
1.
Seat heating, right side
15 A
9.
Brake lamp switch feed
15.
ABS, STC/DSTC
5A
2.
Seat heating, left side
15 A
10.
3.
Horn
15 A
4.
Reserve
Combined instrument
panel (DIM), climate
control (CCM), parking
heater, power driver's
seat
16.
Electronic power steering (ECPS)*, Active
Xenon (HCM)*, headlamp levelling*
10 A
10 A
5.
Infotainment system
6.
-
-
Front seat, rear seat
and refrigerator socket*
17.
Fog lamp, front left
7.5 A
15 A
18.
Fog lamp, front right
7.5 A
7.
-
-
12.
-
-
19.
-
8.
Siren*
5A
13.
-
-
20.
Coolant pump (V8)
14.
-
-
10 A
11.
* Option/accessory, for more information, see Introduction.
5A
5A
09 Maintenance and service
Fuses
21.
Transmission control
module (TCM)
10 A
22.
Main beam, left
10 A
23.
Main beam, right
10 A
24.
-
-
25.
-
-
26.
-
-
27.
-
-
28.
Power passenger
seat*, Rear Seat Entertainment (RSE) *
09
5A
29.
Fuel pump
7.5 A
30.
BLIS*
31.
-
-
32.
-
-
33.
Vacuum pump (petrol)
20 A
34.
Washer pump
15 A
35.
-
-
36.
-
-
5A
``
* Option/accessory, for more information, see Introduction.
225
09 Maintenance and service
09
Fuses
G032342
Fuses in the cargo area
1.
2.
10 A
Position lamps, fog
lamps, cargo area lighting, number plate lighting, lamps in brake
lighting
20 A
3.
Accessories (AEM)*
15 A
4.
Reserve
5.
6.
226
Reversing lamp
REM electronics
RSE system*
7.
Towing bracket wiring*
(30-feed)
15 A
8.
Cargo area socket
15 A
9.
Rear right door: Power
window, power window
lock
10.
10 A
7.5 A
Rear left door: Power
window, power window
lock
20 A
Diesel filter heater
15 A
14.
Subwoofer, rear air
conditioning (A/C) *
15 A
15.
-
-
16.
-
-
17.
Infotainment system
accessories*
20 A
18.
-
19.
Rear wiper
11.
-
-
12.
-
-
* Option/accessory, for more information, see Introduction.
13.
5A
15 A
09 Maintenance and service
Fuses
20.
Towing bracket wiring*
(15-feed)
20 A
21.
-
-
22.
-
-
23.
AWD
24.
-
-
25.
-
-
26.
Park Assist*
5A
27.
Main fuse: Towing
bracket wiring, parking
assistance, AWD
30 A
Central locking system
(PCL)
15 A
Trailer lighting, left:
Position lamps, direction indicator*
25 A
Trailer lighting, right:
brake lamp, rear fog
lamp, direction indicator*
25 A
31.
Main fuse: Fuse 37, 38
40 A
32.
-
28.
29.
30.
7.5 A
33.
-
-
34.
-
-
35.
-
-
36.
-
-
37.
Heated rear window
20 A
38.
Heated rear window
20 A
09
-
``
* Option/accessory, for more information, see Introduction.
227
09 Maintenance and service
09
Fuses
G031532
Fuses in the cargo area - Executive*
The fuse box is located behind the cover panel
on the left-hand side.
1.
2.
3.
4.
228
Relay, seat heating,
rear seat, Relay, massage seat, front
5A
Seat heating, rear seat,
left
15 A
Seat heating, rear seat,
right
15 A
Ventilated seat front,
Massage seat front
10 A
5.
-
-
6.
-
-
* Option/accessory, for more information, see Introduction.
09 Maintenance and service
09
229
General..................................................................................................
Control panels, audio ...........................................................................
Audio system functions ........................................................................
Radio functions ....................................................................................
CD functions ........................................................................................
Menu structure – audio system ............................................................
Phone functions* ..................................................................................
Menu structure – phone .......................................................................
Bluetooth handsfree* ...........................................................................
RSE - Rear Seat Entertainment system - Dual Screen* .......................
230
* Option/accessory, for more information, see Introduction.
232
233
236
240
246
248
249
256
259
265
INFOTAINMENT SYSTEM
10 Infotainment system
General
Infotainment system
10
Infotainment is a system that integrates the
audio system and phone functions.
You can easily and conveniently use your Infotainment system by means of the joint control
panel or the steering wheel keypad.
XC90 can be equipped with Dolby Surround
Pro Logic II1. This offers an optimal sound
experience very close to being there with a
broad, natural sound profile.
The system also allows your passengers to use
headphones* with separate audio sources.
Dolby Surround Pro Logic II1
Dolby Surround Pro Logic II distributes the two
stereo audio channels to left, centre, right and
rear speakers. This provides a more realistic
sound quality than that provided by standard
two-channel stereo.
Dolby Surround Pro Logic II and the
Dolby icon are trademarks of Dolby
Laboratories Licensing Corporation.
Dolby Surround Pro Logic II System
is manufactured under license from Dolby
Laboratories Licensing Corporation.
1
232
Applies to Premium Sound.
* Option/accessory, for more information, see Introduction.
10 Infotainment system
Control panels, audio
Audio controls
10
CD – shortcuts
VOLUME - Volume (knob control)
POWER - Audio On/Off
AM/FM-shortcut between FM1, FM2 and
AM
Display
ENTER - select in the menu, activate a
selection or access the folder structure and
start playback of audio files if there is a disc
containing audio files in the CD player. For
more information, see page 246.
PHONE - Phone On/Off/Standby
MY KEY – programmable shortcut key for
your favourite function
SELECTOR - select audio source (rotary
control)
SOUND – audio settings
EXIT/CLEAR – scroll back in the menu,
cancel a selection, put the phone in
standby mode, or erase the previous character when entering text and numbers
CD player and CD changer*
Seek/change tracks/stations or scroll forward and back when entering text and digits
Station setting buttons/selecting CD
changer position* (1-6), number and character buttons for the phone and menu
shortcuts
IR* - receiver for remote controls
SIM card holder
MENU – menu selection buttons
CD and CD changer eject*
``
* Option/accessory, for more information, see Introduction.
233
10 Infotainment system
Control panels, audio
Steering wheel keypad
10
Menus
Shortcuts
Menu options are numbered and can also be
selected directly with the keypad 1-6.
Audio – Phone*
My own shortcut button – MY KEY
Use MY KEY to store a favourite function in the
menu, e.g. TP.
G027112
The four buttons at the bottom of the steering
wheel keypad control both the radio and the
phone. The function of the respective button
depends on which system is active. The steering wheel keypad can be used to adjust volume, switch between preset stations and
change CD tracks. The two upper buttons in
the keypad (Yes and No) are used to answer
and end phone calls respectively.
Some infotainment system functions are controlled via a menu system. The current menu
level is shown at the top right of the display.
Menu options are shown in the middle of the
display.
• MENU leads to the menu system. Up/
down with the buttons
menu options.
scrolls between
• ENTER selects or activates/deactivates a
menu option.
• EXIT leads back one step in the menu
structure. A long press on EXIT will exit the
menu system.
Select the function in the menu to be
stored by holding MY KEY depressed for
more than two seconds.
When My Key stored. is shown in the display,
the function has been stored.
Activate the function with a short press on
MY KEY.
Functions that can be stored with MY
KEY
Random
Disc text
TP
News
Radio text
PTY scan
AF
Regional
Surround
234
* Option/accessory, for more information, see Introduction.
10 Infotainment system
Control panels, audio
Control panel with headphones
socket*
Limitations
The audio source (FM, AM, CD etc.) played
back in the speakers cannot be controlled from
the rear control panel.
10
G026982
RDS messages may not appear if the radio is
playing back in the headphones while another
audio source is playing back in the speakers.
Headphones with an impedance of 16 – 32
ohm and sensitivity of 102 dB or higher are
recommended for best sound reproduction.
Activating/deactivating
The control panel is activated with SEL when
the audio system is active. Deactivation is
automatic when the audio system is deactivated or with a long press on SEL.
Scroll/search forward and backward
Short presses on
/
are used to scroll
between CD tracks or preset radio stations.
Long presses are used to fast-wind CD tracks
or to search for radio stations automatically.
* Option/accessory, for more information, see Introduction.
235
10 Infotainment system
Audio system functions
On/Off switch – Audio
Volume control
10
Turn the knob
clockwise or anticlockwise to
raise or lower the volume respectively. The volume control is electronic and has no end position. Volume can also be raised (+) or lowered
(–) using the steering wheel keypad.
Sometimes the external AUX audio source can
be heard at a different volume to the internal
audio sources. The audio quality may be
impaired if the audio volume from the external
audio source is too high or too low. Prevent this
by adjusting the input volume of the external
audio source:
Selecting the audio source
1. Select AUX input volume in the menu and
press ENTER.
G027115
Press the AM/FM
button repeatedly to toggle between FM1, FM2 and AM. The CD button
activates the CD player/changer.
Press the POWER button
audio system on or off.
to switch the
If the audio system is active when the ignition
is switched off, it will reactivate automatically
when the car is restarted.
Turn SELECTOR
to toggle between the
external audio sources - AUX and USB*, and
the internal audio sources - FM1, FM2, AM, CD
and CD changer*.
External audio sources
AUX
The AUX AUX input can be used for connecting
an iPodŸ or an MP3 player.
NOTE
The audio quality may be impaired if the
player is charged while the audio system is
in AUX mode. In which case, avoid charging
the player.
236
* Option/accessory, for more information, see Introduction.
2. Control the volume with SELECTOR or up/
down with the buttons
. Finish with
ENTER.
NOTE
Does not work for the steering wheel keypad.
10 Infotainment system
Audio system functions
2. Connect your iPodŸ, MP3 player or USB
memory stick to the USB connection*, see
preceding illustration.
> The text Loading appears on the display when the system loads the file
structure on the storage media. This
takes a while.
USB*
10
When the loading is finished the track information is shown on the display.
G027029
Now it is possible to fast-wind/change tracks
/
:
using the buttons
• Short presses are used to scroll between
tracks.
Input for external audio source (AUX) 3.5 mm.
• Long presses are used to fast-wind tracks.
USB connection*.
IMPORTANT
The cover for the cup holders must be open
when the connector is in the AUX input.
If you choose to connect an iPodŸ, MP3 player
or a USB memory stick to the USB connection* then you can control the media via the
car's audio controls.
The steering wheel keypad can also be used
for this purpose.
NOTE
The system supports the playback of music
files in the MP3, WMA and WAV file formats.
However, there are variants of these file formats that are not supported by the system.
The system also supports most iPodŸ models produced in 2005 or later. iPodŸ Shuffle
is not supported.
NOTE
Connect the media player/USB memory
stick to the cable and the port, put in the
parts, and close the glovebox.
1. Select USB using the SELECTOR button.
> Connect device appears on the display.
``
* Option/accessory, for more information, see Introduction.
237
10 Infotainment system
Audio system functions
USB memory stick
10
To facilitate the use of a USB memory stick,
avoid storing any files other than music files in
the memory. It takes considerably longer for
the system to load storage media that contains
items other than compatible music files.
adapt the sound reproduction according to
personal taste.
Audio mode
NOTE
Programme type
Display
shows
Bass
BASS
Treble
TREBLE
BALANCE
Optimum sound reproduction
Balance between the
left and right-hand
speakers
The audio system is calibrated for optimum
sound reproduction by means of digital signal
processing.
Balance between the
front and rear speakers
FADER
Bass speaker level
Subwoofer *
Level for centre speaker
CENTRE *
Level for surround
sound
SURROUND *
The system supports removable media
which is compatible with USB 2.0 and the
FAT32 file system, and can handle a maximum of 500 folders and 64 000 files. The
memory must have a capacity of at least 256
Mb.
This calibration takes into account loudspeakers, amplifiers, passenger compartment
acoustics, listener position etc. for each combination of car model and audio system.
There is a also a dynamic calibration that takes
into account the level set for the volume control, radio reception and vehicle speed.
The controls that are explained in these operating instructions, e.g. Bass, Treble and Equalizer, are only intended for the user to be able to
238
NOTE
The level for the centre speaker can only be
set if Dolby Pro Logic II (DPL II) or three
channel stereo (3-CH) is selected in the
menu. The level for the Subwoofer can only
be set if Subwoofer is activated
1. Press the SOUND button
.
2. Press the SOUND button repeatedly until
you come to the function you wish to set.
Choose between BASS, TREBLE,
FADER, BALANCE, Subwoofer*,
CENTRE* or SURROUND*.
3. Use the SELECTOR knob
to adjust the
level. The display shows a scale from min.
to max. position. The middle indicates the
normal position.
* Option/accessory, for more information, see Introduction.
10 Infotainment system
Audio system functions
Surround*
Bass speaker - SUBWOOFER*
Equalizer rear1
Surround settings govern the spatial perception of the sound. The settings, including activating and deactivating for each respective
audio source, are made separately.
The bass speaker helps the system provide
fuller sound and deeper bass.
This function is used to fine-tune the sound
from the rear speakers.
1. Select AUDIO MODE in the menu and
press ENTER.
1. Select AUDIO MODE in the menu and
press ENTER.
symbol in the display indicates that
The
Dolby Pro Logic II is active. There are three different settings for surround sound:
2. Select Subwoofer and press ENTER. A
check in the box indicates that
Subwoofer is activated.
2. Select Equalizer rear and press ENTER.
• Pro Logic II
• 3 channels
• Off (two channel stereo)
Equalizer front1
Activating/deactivating surround sound
1. Press MENU, scroll to AUDIO MODE and
press ENTER.
This function is used to fine-tune the sound
from the front speakers.
1. Select AUDIO MODE in the menu and
press ENTER.
2. Select SURROUND and press ENTER.
2. Select Equalizer front and press ENTER.
3. Select Pro Logic II, 3 channels or Off and
press ENTER.
3. Use the menu selection buttons or the
SELECTOR knob to set the level.
Dolby Surround Pro Logic II is a trademark
of Dolby Laboratories Licensing Corporation.
Dolby Pro Logic II Surround System is manufactured under license from Dolby Laboratories
Licensing Corporation.
1
10
3. Use the menu selection buttons or the
SELECTOR knob to set the level.
4. Press ENTER to select the next frequency.
You can select five frequencies.
5. Press ENTER until you come to menu
mode to save any changes.
4. Press ENTER to select the next frequency.
You can select five frequencies.
5. Press ENTER until you come to menu
mode to save any changes.
Certain audio systems.
* Option/accessory, for more information, see Introduction.
239
10 Infotainment system
Radio functions
Tuning
Manually seek known frequency
10
LUM
VO E
MY KEY
PHONE
LE CTOR
SE
SOUND
POWER
2
ABC
1
4
GHI
7
PQRS
AUTO
CLEAR
3. Frequency can be adjusted with a short
or
press on one of the arrow keys,
.
MENU
5
6
JK L
MNO
8
9
TUV WXYZ
0
SCAN
#
G027114
*
3
DEF
2. Release the button when the desired frequency shows in the display.
EXI T
ENTER
1. Select radio mode AM/FM1/FM2 using the
SELECTOR knob (3) or the AM/FM button
(1).
2. A short press on the
or
button
is used to search for the next strong station.
3. Press one of the buttons again to search
again.
Manual adjustment mode stays in effect five
seconds after the last press.
Storing stations
To store a selected station under one of the
station setting buttons 0 – 9 (2):
1. Set the desired station.
2. Press and hold the required station storage
button. The sound mutes a few seconds.
Channel stored is shown in the display.
The station is now stored.
You can store up to 10 stations each for AM,
FM1 and FM2, i.e. a total of 30 stations.
240
G027119
AM FM
CD
AUTOSTORE – autostoring stations
1. Hold the
or
button depressed.
MAN is shown in the display. The radio
slowly scrolls in the desired direction,
increasing its tempo after a few seconds.
AUTO (1) seeks out the ten strongest radio stations and stores them automatically in a separate memory. The function is especially useful
in areas where the radio stations and their frequencies are unfamiliar.
Start autostoring
1. Select wavelength using AM/FM.
2. Hold AUTO (1) depressed until
Autostoring appears on the display.
Once Autostoring disappears from the display, the stations are stored. The radio continues in Auto mode and AUTO appears on the
display. The automatically stored stations can
now be selected using the 0 - 9 buttons. If there
10 Infotainment system
Radio functions
is no station with an adequately strong signal
then the display shows No station found.
Cancelling automatic storage of stations
Press EXIT.
Selecting an autostored preset
Allowing the radio to remain in Auto mode provides access to the autostored presets.
1. Briefly press AUTO (1). AUTO appears in
the display.
2. Press one of the 0 - 9 buttons.
3. The radio remains in Auto mode until it is
exited by a brief press on AUTO (1), EXIT
or AM/FM.
Storing a station
A selected station can be stored as a preset
while SCAN is active.
Press one of the 0 - 9 buttons and hold it
depressed until the message Station
stored appears on the display.
SCAN is interrupted and the stored station can
be selected as a preset.
RDS functions
RDS (Radio Data System) links FM transmitters
into a network. An FM transmitter in such a
network sends information that gives an RDS
radio the following functions:
• Automatically switches to a stronger transScanning
SCAN (2) automatically searches through a
wavelength for strong stations. When a station
is found, it is played for approx. 8 seconds
before scanning is resumed.
Activating/deactivating Scan
1. Select wavelength using AM/FM.
2. Press SCAN (2) to activate. SCAN appears
in the display.
3. Close using SCAN or EXIT.
mitter if reception in the area is poor.
• Searches for programme form, such as
traffic information or news.
• Receives text information on the current
radio programme.
NOTE
Some radio stations do not use RDS or only
a selected range of its functions.
Volume control – NEWS/TP/ALARM
NOTE
10
If a CD for example is playing when the radio
receives a traffic bulletin, the CD player is
put in pause mode. The message is played
at the volume selected for that type of message. Playback of the originally selected
audio source is then resumed at the previous volume. If volume is adjusted while the
bulletin is played, the new volume is saved
and used for the next bulletin.
News – NEWS
This function interrupts other sound sources,
e.g. CD, when a news broadcast starts.
1. Select radio mode using the SELECTOR
knob or the AM/FM button.
2. Select News in the menu and press
ENTER.
3. News appears on the display.
4. Select News again and press ENTER to
deactivate the News function.
With this function, programmes from RDS stations that are news-coded will interrupt other
audio sources using the volume setting for this
specific purpose. As soon as the news broadcast is finished, the audio system returns to the
``
241
10 Infotainment system
Radio functions
previous audio source and resumes the previous volume setting.
10
If you do not wish to listen to a news item in
progress;
Press the EXIT button. The NEWS function
remains active and the radio waits for the
next news programme.
Traffic information – TP
This function interrupts other audio sources in
order to broadcast traffic information from RDS
stations. The message is heard at the volume
set for this specific purpose. As soon as the
message ends, the radio returns to the previous audio source and volume setting.
1. Select TP in the menu and press ENTER.
2. TP appears on the display.
3. Select TP again and press ENTER to deactivate the TP function.
TP is shown in the display when this function
is active. If the set station can send traffic inforappears on the display.
mation then
Traffic information will only interrupt the sound
source if
is shown in the display.
If you do not wish to listen to a traffic bulletin
in progress;
Press the EXIT button. The TP function
remains active and the radio waits for the
next traffic bulletin.
TP Search
This function allows you to listen to traffic information when travelling between different countries and states in Europe without needing to
select a station.
1. Select RADIO SETTINGS in the menu and
press ENTER.
Programme types – PTY
The PTY function can be used to select different programme types, such as pop or classical
music. Use the PTY function to select from
among the different programme types shown
in the list below.
2. Select TP and press ENTER.
3. Select TP search and press ENTER.
To deactivate the function, select TP search
again and press ENTER.
Radio text
Some RDS stations transmit information on
programme content, artists, etc. This information can be indicated with text in the display.
Display of programme type
1. Select RADIO SETTINGS in the menu and
press ENTER.
2. Select PTY in the menu and press
ENTER.
3. Select Show PTY and press ENTER.
The PTY of the selected station is now shown
in the display.
1. Press the MENU button.
2. Select Radio text in the menu and press
ENTER.
3. Select Radio text again and press
ENTER to deactivate.
Alarm
Alarms are transmitted automatically and the
function cannot be deactivated. Alarm! is
shown in the radio display when an alarm mes-
242
sage is broadcast. This function is used to warn
motorists of major accidents and catastrophes, such as a bridge collapse or an accident
at a nuclear plant.
NOTE
Not all radio stations have a PTY designation.
10 Infotainment system
Radio functions
Programme types
Programme types
Current affairs
Pop music
3. Select PTY and press ENTER.
4. Select Select PTY and press ENTER.
Religion
Travel
Varied speech
Rock music
Country music
Social affairs
5. Press ENTER for one or more of the listed
programme types you select. The PTY
symbol in the display illuminates when the
first selection is made and the radio continues in standby for PTY.
Documentary
Sport
6. Once you have selected all desired types,
select EXIT/CLEAR to exit the PTY list.
Finance
Drama
Folk music
Phone in
Leisure & hobby
Education
Children's progs
Science
Oldies music
Weather & Metro
Information
Other music
Jazz music
Searching for a specific programme type
Serious classic
This function helps you find programmes with
a specific focus by searching the entire frequency band.
Culture
Light classic
Easy listening
National music
1. Select FM 1 or FM 2 and press the
MENU button.
2. Select RADIO SETTINGS and press
ENTER.
10
7. Select PTY scan and press ENTER. If the
radio finds a station with the selected programme type, it is played through the
speakers.
8. If the radio finds a station that is unsuitable,
/
continue the search with the
buttons.
9. If no stations with the selected programme
type are found, the radio resumes its previous frequency. PTY then remains in
standby mode until the selected programme type is broadcast, at which time
the radio automatically switches to the station sending the selected programme type.
In order to deactivate PTY standby, enter the
menu and select Clear all PTY. The symbol
PTY disappears from the display and the radio
resumes normal mode.
``
243
10 Infotainment system
Radio functions
10
Traffic information – TP STATION
News – NEWS STATION
Automatic frequency update – AF
Here, you set from which station traffic information is to be heeded.
Here, you set from which station news is to be
heeded.
must be shown in the display
Note that
for this to work.
Note that the set station in question must be an
RDS station for this to work.
Activating/deactivating TP STATION
Activating/deactivating NEWS STATION
The AF function selects one of the strongest
transmitters for a set station. The radio may
sometimes need to search through the entire
FM wavelength to find a strong transmitter. If
this occurs, the radio mutes and PI Seek
Press EXIT to cancel appears in the display.
Listen to the station from which traffic information is to be heeded.
Listen to the station from which news is to be
heeded.
1. Select RADIO SETTINGS in the menu and
press ENTER.
1. Select RADIO SETTINGS in the menu and
press ENTER.
2. Select TP and press ENTER.
2. Select NEWS STATION and press
ENTER.
3. Select TP-STATION and press ENTER.
4. Select Set current to activate or RESET
to deactivate and press ENTER.
NOTE
Now only traffic information from the stored
station will by played.
Activating/deactivating AF
1. Select RADIO SETTINGS in the menu and
press ENTER.
2. Select AF and press ENTER.
To reactivate AF, select AF and press
ENTER.
3. Select TP STATION and press ENTER.
4. Select Set current to activate or RESET
to deactivate and press ENTER.
NOTE
Now only news from the stored station will
by played.
Regional radio programmes – REG
This function causes the radio to continue with
a regional transmitter even if its signal strength
is low.
1. Select RADIO SETTINGS in the menu and
press ENTER.
2. Select Regional and press ENTER.
3. REG appears on the display.
4. To deactivate the REG, select REG again
and press ENTER.
244
10 Infotainment system
Radio functions
Enhanced Other Networks – EON
Resetting RDS functions
The EON function is especially useful in urban
areas with many regional radio stations. It
allows the distance between the car and the
radio station transmitter to determine when
programme functions should interrupt the current audio source.
Resets all radio settings to the original factory
settings.
2. Select Reset all and press ENTER.
• Local – interrupts only if the radio station
3. Press ENTER again to confirm.
10
1. Select RADIO SETTINGS in the menu and
press ENTER.
transmitter is close.
• Distant1 – interrupts if the station transmitter is far away, even if there is a lot of
static.
• Off – no interruption for programmes from
other transmitters.
Activating/deactivating EON
1. Select RADIO SETTINGS in the menu and
press ENTER.
2. Select EON and press ENTER.
3. Select Local, Distant or Off and press
ENTER.
1
Default/factory settings.
245
10 Infotainment system
CD functions
10
Inserting a CD (CD changer)
Audio files
Apart from normal music CDs, the CD player
supports MP3 and WMA format audio files.
Select an empty position with the number
buttons 1 - 6 or Up/Down on the navigation
button.
An empty position is marked on the display.
The text Insert disc shows that a new disc can
be inserted. The CD changer can hold up to six
CDs.
Insert a CD into the CD changer slot (2).
G027116
CD eject
A CD will stay in the ejected position for max.
12 seconds. Following which it is re-inserted in
the player and playback continues.
Starting playback (CD player)
Single discs (CD player)
If a music CD is in the player when the audio
system is in CD mode then playback is started
automatically. Otherwise, load a disc and
change to CD mode using SELECTOR (4) or
CD(1).
Eject individual discs by pressing the eject button (3).
Starting playback (CD changer)
If a CD position with a music CD is already
selected when the audio system is activated
then playback starts automatically. Otherwise
change to CD changer mode using
SELECTOR (4) or CD (1) and select a disc with
the number buttons 1 - 6.
All discs (CD changer)
Eject all discs with a long press on the eject
button. The entire magazine is emptied disc by
disc. The message MATA UT is shown in the
display.
This function can only be activated if the car is
stationary. Eject is interrupted if the car begins
to move.
Pause
If the volume is turned down completely, the
CD player is stopped. The player is restarted
when volume is increased.
246
NOTE
Certain types of copy-protected audio files
cannot be read by the player.
When a CD containing audio files is inserted
into the player the disc's directory structure is
read in. It may take a while before playback
starts due to the quality of the disc.
Navigation and playback
If a disc containing audio files is inside the CD
player then ENTER leads to the disc's directory structure. The directory structure is navigated in the same way as the audio system's
menu structure. Audio files have the symbol
and directories have the symbol
. Before playback starts
/
can
be used to show the audio file's name if the
display is too narrow. Start playback of the
selected audio file with ENTER.
When the playback of a file is finished the playback of the other files in the same directory
continues. Directory change takes place automatically when all files in the current directory
have been played back.
10 Infotainment system
CD functions
Fast-wind/change CD tracks and audio
files
Activating/deactivating (CD player)
Short presses right/left on the
/
buttons are used to scroll between CD tracks/
audio files. Long presses are used to fast-wind
CD tracks/audio files. The steering wheel keypad can also be used for this purpose.
Scan CD
This function plays the first ten seconds of
each CD track/audio file. Press SCAN to activate. Interrupt with EXIT or SCAN to continue
playback of the current CD track/audio file.
Scan only works on the selected disc. The text
SCAN is shown in the display when the function is active.
NOTE
If disc text is activated then SCAN is not
shown in the display.
Random
This function plays the tracks in random order.
The random CD tracks/audio files can be scrolled through in the normal way.
NOTE
It is only possible to scroll between random
CD tracks on the current disc.
• RANDOM means that the tracks from only
one music CD are played.
If a normal music CD is being played:
Select RANDOM in the menu and press
ENTER.
If a disc with audio files is being played:
• RANDOM ALL means that all tracks on all
• RANDOM Folder means that the audio
files in a directory on the current CD are
played.
Select Disc or Folder in the menu and
press ENTER.
NOTE
Activating/deactivating (CD changer)
If a normal music CD is being played:
If disc text is activated then these messages
are not displayed.
1. Select Random in the menu and press
ENTER.
2. Scroll to Single disc or All discs and press
ENTER.
The option All discs only applies to the music
CDs in the changer.
If a CD with audio files is being played:
1. Select Single disc or Folder in the menu
and press ENTER.
2. Scroll to the required CD or folder and
press ENTER.
When you select another CD the function is
deactivated.
Different messages appear depending on
which random function is active:
10
music CDs in the CD changer are played.
Disc text
If title information is stored on a CD then it can
be shown in the display.
Activating/deactivating
Start CD playback.
Select Disc text in the menu and press
ENTER.
CDs
Using CD discs burned at home could result in
poor or non-existent sound.
WARNING
Only use standard discs (12 cm in diameter).
Do not use CDs with adhesive disc labels.
The heat in the CD player may cause the
label to come off, damaging the CD player.
247
10 Infotainment system
Menu structure – audio system
10
FM-MENU
AM MENU
1.
News
1.
2.
TP
3.
Radio text
CD MENU
4.
RADIO SETTINGS
1.
Random
4.1.
PTY
2.
News
4.2.
TP
3.
TP
4.3.
NEWS STATION
4.
Disc text
4.4.
AF
5.
AUDIO SETTINGS*1
4.5.
Regional
4.6.
EON
4.7.
Reset all
5.
AUDIO SETTINGS*
5.1.
1
248
Surround
5.2.
Subwoofer
5.3.
Equalizer front
5.4.
Equalizer rear
5.5.
Reset all
AUDIO SETTINGS*1
AUX MENU
1.
AUX input volume
2.
News
3.
TP
4.
AUDIO SETTINGS*1
See FM MENU.
* Option/accessory, for more information, see Introduction.
10 Infotainment system
Phone functions*
10
Phone system components
``
* Option/accessory, for more information, see Introduction.
249
10 Infotainment system
Phone functions*
10
Steering wheel keypad* - You can control
the majority of phone functions using the
steering wheel keypad. When the phone is
active, the steering wheel keypad can only
be used for phone functions. When in
active mode, phone information is always
shown in the control panel display.
Microphone - The microphone for handsfree is fitted in the roof by the sun visor.
Centre console control panel - All phone
functions (except call volume) can be regulated via the control panel.
General
set*, park the car in a safe place first.
• Switch off the phone system when refuelling the car.
• Switch off the system near blasting work.
• Volvo recommends that an authorised
Volvo workshop carries out phone system
servicing.
Emergency calls
SIM card reader - The SIM card is inserted
into the front of the control panel.
Emergency calls to alarm centres can be made
without a SIM card as long as there is coverage
by a GSM operator.
Privacy handset* - The privacy handset
can be used when you do not wish to be
disturbed.
1. Activate the phone.
Antenna - The antenna is mounted against
the windscreen, in front of the rearview
mirror.
Controls
• Always put traffic safety first.
• If the driver needs to use the privacy hand-
2. Ring the emergency number that applies to
your region (within EU: 112).
3. Press ENTER in the control panel or in the
steering wheel keypad.
G027117
Phone system components
Display
ENTER – accept a call, make a menu
selection or activate the phone from
standby mode
On/Off/Standby
EXIT/CLEAR – terminate/refuse a call,
scroll back in the menu, cancel a selection
or erase entered digits/characters
SIM card holder
Menu selection buttons
250
* Option/accessory, for more information, see Introduction.
10 Infotainment system
Phone functions*
On/Off/Standby switch
Volume reduction during phone call
To activate the system:
If the phone rings when the radio is switched
on, the volume is lowered when the call is
answered. When the call is concluded, the volume returns to the previously set level. Radio
volume can also be adjusted during a phone
call, whereby the newly selected level will
resume when the call is concluded. Audio system volume can also be switched off completely during a phone call, see page 258.
Press the PHONE button (3) to activate the
phone system.
To switch off the system:
Hold the PHONE button depressed to
switch off the phone system
Continuing with system in standby mode:
Number/character buttons and menu
shortcuts
Seek – scroll forward or back when entering text and numbers
Increase/decrease call volume during
calls. The phone does not use the centre
speaker*
1. The phone will continue in standby mode
with a brief press of the PHONE button or
if you press EXIT/CLEAR.
This function only applies to the Volvo integrated phone system.
2. Reactivate the system with the PHONE
button.
Standby mode
When the phone is active or in standby mode,
a handset is shown in the display.
If you switch off the car's ignition with the
phone system on, it will be on the next time you
switch on the ignition. No calls can be received
when the phone system is switched off.
10
In standby mode, you can receive calls while
the audio system is active and information from
audio system sources is shown in the display.
To use other functions of the phone system,
the phone must be in active mode.
Menu shortcuts
Once you have used the menu button to enter
the menu system, you can use numbers
instead of the arrows and the ENTER button to
select the right menu in the main menu level.
Each menu selection is numbered. The numbers are shown in the display together with the
menu alternative.
``
* Option/accessory, for more information, see Introduction.
251
10 Infotainment system
Phone functions*
10
Traffic safety
1. Switch off the phone.
Ending a call
For reasons of safety, parts of the phone menu
system cannot be accessed at speeds in
excess of 8 km/h. You may only complete
menu system activities that have already been
started.
2. Open the SIM card holder with a short
press.
3. Insert the SIM card with the metallic surface down.
The audio system resumes its previous activity.
The speed limiter can be disconnected using
menu function 5.6.
4. Make sure that the bevelled corner of the
SIM card matches the bevel of the holder.
Refuse an incoming call by pressing EXIT/
CLEAR.
Press EXIT/CLEAR on the steering wheel
or control panel keypad or hang up the
handset.
5. Press in the holder.
SIM card
Contact your network operator if you experience difficulties with the SIM card.
Privacy handset*
If you wish to speak without disruptions, use
the privacy handset. Lift the handset by pressing briefly on the top (A).
Making and receiving calls
To call:
Dial the number and press ENTER on the
steering wheel or the control panel keypad
(or lift the handset).
To receive an incoming call:
The phone can only be used with a valid SIM
card Subscriber Identity Module. Your network
operator supplies this card.
The car's audio system can be muted automatically while a phone call is in progress, see
page 258.
Always insert the SIM card when you wish to
use the phone.
252
Press ENTER or lift the handset. You can
also use Automatic Answer, see
page 258.
* Option/accessory, for more information, see Introduction.
G026983
G026980
Select the desired phone number using the
centre console keypad and lift the handset
10 Infotainment system
Phone functions*
to place the call. Adjust the volume with the
dial on the side of the handset.
The call is ended when you replace the handset
in its holder.
If you wish to switch to handsfree without ending the call:
1. Press
on the steering wheel keypad
(or control panel menu buttons) and select
Handsfree.
2. Press ENTER and hang up the handset. If
the handset is already removed from its
cradle when a call is started, the ringing
party will be audible in the handsfree system.
3. Press the MENU button, scroll to Handset
and press ENTER in order to transfer to the
handset.
Last dialled numbers
The phone automatically stores the last phone
numbers/names called.
1. Press ENTER on the steering wheel or
control panel keypad.
2. Use the menu buttons to scroll forward or
back through the last numbers dialled.
They are shown in the display.
3. Press ENTER.
Speed dial
Call waiting
If you hear two beeps in your speaker during a
phone call, someone else is calling. This function can be selected or deselected in the menu.
Storing speed dial numbers
A number stored in the phone book can be
linked to a speed dial button (1 – 9).
Proceed as follows:
1. Select Phone book in the menu and press
ENTER.
2. Scroll to One-key dial (see page 258) and
press ENTER.
3. Select which number is to be the speed dial
number. Press ENTER to confirm.
4. Search for the desired name or phone
number in the phone book. Press ENTER
to select.
10
When this occurs, you may accept or decline
the call. If you do not wish to take the call, press
EXIT/CLEAR or do nothing.
If you do wish to take the call, press ENTER.
Your current call will be put in "park mode". If
you press EXIT/CLEAR, both calls will be terminated.
Functions during a call
The following functions are available during a
call (scroll with the arrows and press ENTER to
make a selection)
Using speed dial
1. To make a call, press and hold the desired
speed dial button for about two seconds or
press the button briefly and then press
ENTER.
Secret mode/
Secret mode off
Secret mode
Hold/Resume
Choose if the call is
to be parked or
resumed
Handset/Handsfree
Using the handset or
handsfree
Phone book
Show phone book
2. Once you switch on the phone, wait a
moment before using speed dial.
NOTE
If you wish to use a speed dial number then
Menu 3.4 must be activated. See Speed dial
under Description of menu options on page
257.
``
* Option/accessory, for more information, see Introduction.
253
10 Infotainment system
Phone functions*
Secret mode/
Secret mode off
Secret mode
Handset/Handsfree
Using the handset or
handsfree
Phone book
Show phone book
Join
Swap
Phone book
If the number of the person calling is found in
the phone book, his or her name is shown in
the display.
AM FM
CD
LUM
VO E
Switch between the
two calls
LE CTOR
SE
SOUND
EXI T
ENTER
2
ABC
1
4
GHI
7
PQRS
Speak with both
parties simultaneously (conference
call)
MY KEY
PHONE
POWER
The phone memory can store up to 255 names.
Storing phone numbers with names
AUTO
*
3
DEF
CLEAR
MENU
5
6
JK L
MNO
8
9
TUV WXYZ
0
SCAN
#
1. Press the MENU button, select Phone
book and press ENTER.
2. Scroll to New number and press ENTER.
3. Enter a name and press ENTER.
4. Enter a number and press ENTER.
5. Choose in which memory to save and
press ENTER.
Call volume
Increase or decrease call volume during calls
by pressing the + or - buttons in the steering
wheel keypad.
When the phone is activated, the steering
wheel keypad only controls the phone functions.
The phone must be in standby mode in order
to adjust the audio system with these buttons,
see page 251.
254
Dialling from the memory
Phone numbers and names can be stored in
either the phone memory or the SIM card memory.
G027118
10
The following functions are available when you
have a current call and a parked call (scroll with
the arrows and press ENTER to make a selection)
* Option/accessory, for more information, see Introduction.
Press the MENU button's down arrow (1)
in the steering wheel to search in
or
the phone book.
Choose from the following alternatives:
1. Press ENTER and scroll with the arrows
until you find the desired name.
2. Press the key for the first letter of the name
(or enter the entire name) and press
ENTER.
3. Press ENTER to call the selected number.
10 Infotainment system
Phone functions*
Enter a name or message
Press the button with the desired character:
once for the first character, twice for the second, etc. Press 1 to enter a space.
1
space 1- ? ! , . : " ' ( )
2
abc2äåàæç
3
def3èé
4
ghi4ì
5
jkl5
6
mno6ñöòØ
7
pqrs7ß
8
tuv8üù
9
wxyz9
*
Used if two characters are to be
ended with the same button.
0
[email protected]*#&$£/%
#
Switch between upper and lower
case.
EXIT
Delete the last letter or number
entered. If you press for a long
time, the entire number and text is
deleted.
Many network operators offer double SIM
cards - one for your car and one for another
phone. A double SIM card allows you to have
the same number for two different phones. Ask
your network operator about the options available and the use of double SIM cards.
10
Specifications
Quitting text input
1. Clear all entered characters with a long
press on the EXIT/CLEAR button.
2. Return to the menu with an additional long
press on the EXIT/CLEAR button.
Double SIM cards
A
Output
2W
SIM card
small, 3 V
Memory entries
255A
SMS
yes
Data/fax
no
Dualband
yes (900/1800)
The phone memory contains 255 positions. The number of
SIM card memory positions varies depending on your subscription.
G026980
IMEI number
To block the phone, you must provide your
network operator with the phone's IMEI number. This is a 15 digit serial number that is programmed into the phone. Dial *#06# to show
this number in the display. Write it down and
keep it in a safe place.
* Option/accessory, for more information, see Introduction.
255
10 Infotainment system
Menu structure – phone
Overview
10
1.
Speed dial
4.6.2
When engag.
Call register
2.4.1
Active
4.6.3
Not answered
1.1.
Missed calls
2.4.2
Select numbers
4.6.4
Not reachable
1.2.
Received calls
2.5.
Erase SIM
4.6.5
Fax calls
1.3.
Dialled no.
2.6.
Erase phone
4.6.6
Data calls
1.4.
Erase list
2.7.
Memory status
4.6.7
Cancel all
1.5.
2.
1
256
2.4.
1.4.1
All calls
1.4.2
Missed calls
3.1.
Read
5.1.
Car phone
1.4.3
Received calls
3.2.
Write
5.2.
Add phone
1.4.4
Dialled no.
3.3.
Message settings
5.3–7. Added phones1
3.
Messages
5.
Call duration
3.3.1
SMSC number
1.5.1
Last call
3.3.2
Validity time
1.5.2
Call count
3.3.3
Message type
1.5.3
Total time
1.5.4
Reset timer
4.
Call options
4.1.
Send my no.
Phone book
4.2.
Call waiting
2.1.
4.3.
Auto answer
Search
2.2.
New number
4.4.
Automatic redial
2.3.
Copy all
4.5.
Voice mail number
2.3.1
SIM to phone
4.6.
Call divert
2.3.2
Phone to SIM
Max. 5 phones.
4.6.1
All calls
Change phone
NOTE
The menu above only applies to cars with
BluetoothTM handsfree.
6.
Tel. settings
6.1.
6.2.
Network
6.1.1
Auto
6.1.2
Manual select
SIM security
6.2.1
On
6.2.2
Off
10 Infotainment system
Menu structure – phone
6.2.3
Auto
1.4.2.
Missed
2.4. Speed dial
A number stored in the phone book can be
stored as a speed dial number.
6.3.
Change PIN code
1.4.3.
Received
6.4.
Audio
1.4.4.
Dialled
6.5.
2.5. Erase SIM
6.4.1
Ring volume
1.5. Call duration
Erase the entire SIM card memory.
6.4.2
Ring signal
2.6. Erase phone
6.4.3
Mute radio
Duration of all calls or of the most recent call.
The phone code is required to reset the call
timer (see menu 5.4).
6.4.4
Msg. beep
1.5.1.
Last call
1.5.2.
Call count
1.5.3.
Total time
Shows how many positions are occupied in the
SIM card and phone memory. The table shows
how many of the total number of positions are
occupied, e.g. 100 (250).
1.5.4.
Reset timer
Factory settings
Description of menu options
1. Call register
Erase the entire phone memory.
2.7. Memory status
3. Messages
3.1. Read
1.1. Missed calls
2. Phone book
List of missed calls. You can choose to call,
erase or store the number in the phone book.
2.1. Search
Search for a name in the phone book.
Received text messages. Select whether to
erase, forward, change or save the entire message or parts of it.
1.2. Received calls
2.2. New number
List of received calls. You can choose to call,
erase or store the number in the phone book.
Store names and phone numbers in the phone
book, see page 253.
3.2. Write
1.3. Dialled no.
2.3. Copy all
List of dialled numbers. You can choose to call,
erase or store the number in the phone book.
Copy phone numbers and names from the SIM
card to the phone memory.
1.4. Erase list
2.3.1.
From SIM to phone memory
Erase the lists found in the menus 1.1, 1.2 and
1.3 as below.
2.3.2.
From phone to SIM memory
1.4.1.
All
10
Write a message using the keypad. Choose
whether to save or send it.
3.3. Message sett
Enter the number (SMSC number) of the message centre to which messages are to be transferred as well as how long they are to be saved
at the message centre. Contact your network
operator for information on message settings.
Normally, these settings should not be altered.
3.3.1.
SMSC number
``
257
10 Infotainment system
Menu structure – phone
10
3.3.2.
Validity time
4.6.5.
Fax calls
6.2. SIM security
3.3.3.
Message type
4.6.6.
Data calls
Select if the PIN code should be on, off or if the
phone should automatically give the PIN code.
4.6.7.
Cancel all
6.2.1.
On
4.1. Send my no.
5. Change phone
6.2.2.
Off
Displays or hides your phone number to/from
the person you call. Contact your network
operator regarding ex-directory numbers.
5.1. Car phone
6.2.3.
Auto
4. Call options
4.2. Call waiting
Be alerted during a phone call that there is
another incoming call.
4.3. Automatic answer
Automatically answers incoming calls.
4.4. Call back
Calls a previously engaged number.
4.5. Voice mail number
Select the built-in phone.
5.2. Add phone
Add mobile phones to the list Added phones.
Change PIN code. Write down and save the
code in a safe place.
5.3-7. Added phones
6.4. Sounds
Select to connect to one of the added phones
(up to 5 phones).
6.4.1.
Volume
Adjust the ring tone volume.
NOTE
The menu above only applies to cars with
BluetoothTM handsfree.
Stores voice mail number.
6.4.2.
Ring signal
There are five different ring signals.
6.4.3.
On/Off
4.6. Diversions
6. Phone settings
Mute radio.
Choose when and what type of calls are to be
diverted to a specified phone number.
6.1. Network
6.4.4.
4.6.1.
All calls
This setting only applies during the call in progress.
258
6.3. Change PIN code
4.6.2.
When engag.
4.6.3.
Not answered
4.6.4.
Not reachable
Choose a network automatically or manually.
The selected network is shown in the display in
the phone's basic mode.
6.1.1. Auto
6.1.2. Manual select
Msg. beep
6.5. Factory default
Reset the system's factory settings.
10 Infotainment system
Bluetooth handsfree*
General
mobile phone can be operated by its own keys
irrespective of whether or not it is connected.
Phone functions, controls overview
10
NOTE
Only a selection of mobile phones are fully
compatible with the handsfree function.
Volvo recommends that you seek assistance from an authorised Volvo dealer or
visit www.volvocars.com for information on
compatible phones.
System overview.
Mobile phone
Microphone
Steering wheel keypad*
Centre console control panel
Bluetooth TM
A mobile phone equipped with BluetoothTM
can be connected wirelessly to the audio system. The audio system then works handsfree,
with the option to control a range of the mobile
phone's functions remotely. The microphone is
fitted in the headlining by the sun visor (2). The
Centre console control panel.
VOLUME - volume, same functionality
available in steering wheel keypad*.
Display
ENTER – accept a call, make a menu
selection or activate the phone from
standby mode.
PHONE – on/off/standby.
EXIT – terminate/refuse a call, scroll back
in the menu, cancel a selection or erase
entered digits/characters.
MENU - leads to the menu system. Up/
down with the buttons scrolls between
menu options.
``
* Option/accessory, for more information, see Introduction.
259
10 Infotainment system
Bluetooth handsfree*
10
Seek – scroll forward or back when entering text and numbers.
nected previously. To connect a mobile phone
for the first time, follow the instructions below:
Number/character buttons and menu
shortcuts.
Alternative 1 - via the car's menu system
Remember
The menus are controlled from the centre console and the steering wheel keypad. For general information on menus, see page 234.
NOTE
If the car is equipped with both
BluetoothTM handsfree and built-in phone
then there is an additional menu in the
phone menu, see page 263.
Activating/deactivating
A short press on PHONE activates the handsfree function. The text PHONE at the top of the
display shows that it is in phone mode. The
symbol
shows that the handsfree function is active.
One long press on PHONE deactivates the
handsfree function and disconnects a connected phone.
Connect mobile phone
1. Make the mobile phone detectable/visible
via BluetoothTM, see the mobile phone's
manual or www.volvocars.com.
2. Activate the handsfree function with
PHONE.
> Menu option Add phone appears on
the display. If one or more mobile
phones have already been registered
then these are also shown.
3. Select Add phone.
> The audio system searches for mobile
phones in the vicinity. The search takes
approximately 30 seconds. The mobile
phones detected are specified with their
respective BluetoothTM name in the display. The handsfree function's
BluetoothTM name is shown in the
mobile phone as My Car.
4. Choose one of the mobile phones in the
audio system display.
5. Enter the number series shown in the audio
system display via the mobile phone keypad.
A mobile phone is connected in different ways
depending on whether or not it has been con-
260
* Option/accessory, for more information, see Introduction.
Alternative 2 - via the phone's menu system
1. Activate the handsfree function with
PHONE. If there is a phone connected,
disconnect the connected phone.
2. Search with the phone's BluetoothTM, see
the mobile phone's manual.
3. Select My Car in the list of units detected
in your mobile phone.
4. Enter the PIN code '1234' into the mobile
phone when prompted for the PIN code.
5. Select to connect to My Car from the
mobile phone.
The mobile phone is registered and connected
automatically to the audio system while the text
Synchronising is shown in the display. For
more information on how mobile phones are
registered, see page 262.
When the connection is established the symbol
is shown and the mobile phone's
BluetoothTM name is shown in the display. Now
the mobile phone can be controlled from the
audio system.
To call
1. Make sure that the text PHONE is shown
at the top of the display and that the
symbol is visible.
10 Infotainment system
Bluetooth handsfree*
2. Dial the number or use the phone book,
see page 262.
3. Press ENTER.
The call is interrupted with EXIT.
Making and receiving calls
NOTE
Incoming call
Calls are accepted with ENTER even if the
audio system is in CD or FM mode for example.
Refuse or end with EXIT.
Disconnecting the mobile phone
Automatic disconnection takes place if the
mobile phone moves out of the audio system's
range. For more information on connection,
see page 262.
Manual disconnection takes place by deactivating the handsfree function with one long
press on PHONE. The handsfree function is
also deactivated when the engine is switched
off.
When the mobile phone has been disconnected an ongoing call can continue with the
mobile phone's built-in microphone and
speaker.
NOTE
Some mobile phones require that the
changeover from handsfree is confirmed
from the phone's keypad.
Automatic answer
Audio settings
Call volume can be adjusted during calls. Use
the steering wheel keypad*.
Audio system volume
In phone mode (PHONE) the audio system vol-
In call menu
ume can be adjusted as usual with VOLUME.
Press MENU or ENTER during an ongoing call
to access the following functions:
• Mute microphone - audio system microphone is muted.
• Move call to mobile - the call is transferred to the mobile phone.
The audio source can be automatically muted
for incoming calls under PHONE MENU
PHONE SETTINGS SOUNDS AND
VOLUME Mute radio.
Ring volume
NOTE
With certain mobile phones the connection
is terminated when the privacy function is
used. This is normal. The handsfree function
asks if you want to reconnect.
book.
10
Call volume
The automatic answer function means that
calls are accepted automatically. Activate/
deactivate under PHONE MENU CALL
OPTIONS Automatic answer.
• Phone book – searching in the phone
A new call cannot be started during an
ongoing call.
Go to PHONE MENU PHONE SETTINGS
SOUNDS AND VOLUME Ring volume
and adjust with
/
on the control panel in
the centre console.
Ring signals
The handsfree function has integrated ring signals that can be selected under
PHONE MENU PHONE SETTINGS
``
* Option/accessory, for more information, see Introduction.
261
10 Infotainment system
Bluetooth handsfree*
10
SOUNDS AND VOLUME
Ring signal 1 etc.
Ring signals
NOTE
The connected mobile phone's ring signal is
not deactivated when one of the handsfree
system's integrated signals is used.
In order to select the connected phone's ring
signal1, go to PHONE MENU PHONE
SETTINGS SOUNDS AND VOLUME
RING SIGNALS Use mobile phone signal.
More on registering and connecting
A maximum of five mobile phones can be registered. Registration is performed once per
phone. After registration the mobile phone is in
the list of added phones. Not more than one
mobile phone can be connected at a time.
Phones can be deregistered under PHONE
MENU BLUETOOTH Remove phone.
to manual connection of another phone, press
EXIT.
Manual connection
If you want to connect a mobile phone other
than the last connected or change the connected mobile phone, proceed as follows:
Set the audio system in phone mode
(PHONE) and follow the instructions on the
display or change the connected mobile phone
by using the menu system as described below.
The menu structure is available in two variants
depending on whether the car only has
BluetoothTM or if the car also has a built-in
phone.
• For cars with only BluetoothTM the connection is made under PHONE MENU
BLUETOOTH Change phone Add
phone or select one of the previously connected phones.
• For cars with built-in phone and
Automatic connection
When the handsfree function is active and the
last mobile phone connected is in range it is
connected automatically. When the audio system searches for the last phone connected its
name is shown in the display. To change over
1
262
Not supported by all mobile phones.
* Option/accessory, for more information, see Introduction.
BluetoothTM the connection is made under
PHONE MENU Change phone Add
phone or select one of the previously connected phones.
Phone book
All use of the phone book presupposes that the
text PHONE is shown at the top of the display
and that the
symbol is visible.
The audio system stores a copy of the phone
book from each registered mobile phone. The
phone book is copied automatically to the
audio system during each connection. Deactivate the function under PHONE SETTINGS
Synch. phone book. Searching for contacts is only performed in the connected
mobile phone's phone book.
NOTE
If the mobile phone does not support copying of the phone book then List is empty is
shown when copying is finished.
If the phone book contains a ringing caller's
contact information then this is shown in the
display.
Searching for contacts
The easiest way to search in the phone book is
with long presses on the keys 2–9. This starts
a search in the phone book based on the key's
first letter.
10 Infotainment system
Bluetooth handsfree*
The phone book can also be reached with the
button on the control panel in the centre
on the steering wheel
console or with
keypad. Scroll between contacts with the
/
buttons or with
/
. The search can
also be carried out from the phone book's
Search menu under PHONEBOOK
Search:
1. Enter the first few letters of the contact and
press ENTER. Or simply press ENTER.
2. Scroll to a contact and press ENTER to
call.
no number stored then this menu can be
reached with one long press on 1. Press 1 for
a long time to use the stored number.
Menu structure - BluetoothTM
handsfree
Call lists
The call lists are copied to the handsfree function at each new connection and are then
updated during the connection. Press ENTER
to show the last dialled. Other call lists are
available under CALL REGISTER.
The menu for BluetoothTM handsfree is
available in two variants. For cars with only
BluetoothTM handsfree and for cars with
built-in phone and BluetoothTM handsfree.
1.
NOTE
Certain mobile phones show a list of the last
dialled calls in reverse order.
Voice recognition
The mobile phone's voice recognition function
for dialling can be used by holding in ENTER.
NOTE
Only a selection of mobile phones are fully
compatible with the voice recognition function. Volvo recommends that you contact an
authorised Volvo dealer or visit
www.volvocars.com for information on
compatible phones.
Inputting text
2.
Input text using the keypad in the centre console. Press once for the key's first character,
twice for the second etc. Continue pressing for
more characters, see the table on page 255.
A short press on EXIT deletes an input character. One long press on EXIT clears all input
/
on the control panel in the
characters.
centre console scrolls between the characters.
3.
CALL REGISTER
1.1.
Last 10 missed
1.2.
Last 10 received
1.3.
Last 10 dialled
PHONEBOOK
2.1.
Search
2.2.
Copy to phone
BLUETOOTH
3.1.
Change phone
3.1.1.
Add phone
3.1.2–6.Added phones2
3.2.
Remove phone
Voice mail number
3.3.
Connect fr. mobile phone
Voice mail number can be changed under
CALL OPTIONS Voice mail no.:. If there is
3.4.
Bluetooth info. for the car
2
10
NOTE
A maximum of 5 phones.
``
* Option/accessory, for more information, see Introduction.
263
10 Infotainment system
Bluetooth handsfree*
4.
10
5.
CALL OPTIONS
4.1.
Automatic answer
4.2.
Voice mail no.:
4.
Automatic answer
4.2.
Voice mail no.:
5.1.1.
Ring volume
5.1.2.
Ring signals
5.1.
Carphone
5.1.3.
Mute radio
5.2.
Add phone
5.
264
Change phone
5.3–7. Added phones 2
Synch. phone book
PHONE SETTINGS
6.1.
CALL REGISTER
1.1.
Last 10 missed
1.2.
Last 10 received
1.3.
Last 10 dialled
PHONEBOOK
2.1.
Search
2.2.
Copy to phone
BLUETOOTH
3.1.
2
Bluetooth info. for the car
4.1.
SOUNDS AND VOLUME
6.
3.
3.3.
CALL OPTIONS
5.1.
Menu structure - BluetoothTM
handsfree with built-in phone
2.
Connect fr. mobile phone
PHONE SETTINGS
5.2.
1.
3.2.
Remove phone
A maximum of 5 phones.
* Option/accessory, for more information, see Introduction.
6.2.
SOUNDS AND VOLUME
6.1.1.
Ring volume
6.1.2.
Ring signals
6.1.3.
Mute radio
Synch. phone book
10 Infotainment system
RSE - Rear Seat Entertainment system - Dual Screen*
General
The RSE system can be used at the same time
as the car's infotainment system.
When the rear seat passengers are using DVD,
RSE-AUX or watching TV1 while listening with
headphones, the driver and front seat passenger can still use the car's radio or CD player.
TV overview
System settings
Press
and select TV I DVD I AUX
TV MEDIA MENU.
Audio mode
When the system has been used once without
the ignition in position I it is blocked. To restart,
ignition position I must be activated.
Time zone setting
Channel lock list
CI module
NOTE
In the event of extended use (more than 10
minutes) with the engine switched off - the
capacity of the car's battery may decrease
to such a low level that the engine cannot
be started.
In which case a message will appear on the
screen.
1
No CAM inserted
CI module information
Channel management
Channel search
10
Factory default
Power consumption, ignition positions
The system can be activated in ignition position
I or II and while the engine is running. When the
car is being started the film stops temporarily
and continues when the engine has started.
TV
Signal strength
Management of
new carriers
System settings TV
Add carrier
Press MEDIA MENU
TV.
Information on frequency
Languages
Delete a frequency
TV menu language
Delete all frequencies
Pict. format
Auto scan
System settings
E.g. English
16:9
4:3
Auto
TV is an option for the RSE system.
``
* Option/accessory, for more information, see Introduction.
265
10 Infotainment system
RSE - Rear Seat Entertainment system - Dual Screen*
Standard
Audio - 1, e.g. ENG.
Audio - 2, e.g. GER.
Zoom
Full screen
Audio mode
Audio
Audio mode
Right
Centered
Left
Right
Stereo
Left
AC3
Banner timeout
System settings-Factory settings
The menus can be
displayed for
between
8-40 seconds.
Press MEDIA MENU
Factory default.
System settings
The system's factory settings are restored
here.
System settings-Sound mode
System settings-Time zone settings
Press MEDIA MENU
Audio mode.
Press MEDIA MENU
Time zone setting.
System settings
The original speech for a TV programme can
be replaced with speech in another language if
the programme is broadcast with several audio
tracks.
System settings
For local programme times to be displayed
correctly the time zone must be set. The
GUIDE and INFO button menus and the clock
are affected by local time zones.
Pay channels
To watch pay channels a payment card must
be fitted in an adapter which is inserted into the
digital TV box.
266
* Option/accessory, for more information, see Introduction.
G031511
10
Mode (screen
mode)
The digital TV box is located on the right-hand
side of the cargo area
1. The box is protected by a cover. Open the
small hatch above the cover.
2. Open the rubber cover on the box.
3. Fit the payment card into the adapter.
Make sure that it is fitted correctly.
4. Insert the adapter in the digital TV box.
Make sure that it is inserted correctly.
> The system will detect that it has
received new information.
5. Search to find the new channels that have
become available, see the section "Payment card TV channels" below.
10 Infotainment system
RSE - Rear Seat Entertainment system - Dual Screen*
> The sound is directed to the headphones.
Payment card TV channels
Search so that the system identifies the payment card's channels.
1. Press MEDIA MENU on the remote control.
2. Select Channel search
3.
Select country and press
3. Adjust the audio volume in the headphones
using the volume control/wheel on the
headphones.
A B on
tem in MODE-AUX and press
the remote control to listen via the speakers.
.
Formats supported by the digital TV box
2.
Playing back a CD disc
1. Insert the CD with the label side turned
from the buttons.
> The disc starts to play back automatically.
2. Switch on the wireless headphones, select
CH A for left-hand screen or CH B for righthand screen.
Press
.
Press
.
10
or
Change CD track with
fast-wind by holding the buttons
depressed.
Pause
1.
2.
3.
Pause and restart the disc with
Stop the disc with
Press
.
.
again to eject the disc.
Discs copied privately can be used.
However, playback and quality depend on the
quality of the source file, format and disc quality.
3. Scroll using the navigation buttons to
select a file.
4.
Music
Selecting within a disc directory
1. Load the disc.
Confirm with
Change CD track
Alternatively - activate the car's audio sys-
Auto scan.
The TV system supports MPEG-2 transmissions. There is the option to receive
MPEG-4 transmissions if you buy an adapter.
This adapter is inserted into the digital TV box
and is fitted in the same way as the adapter for
the payment card. See the section "Pay channels" above.
3.
to select the subdirectory.
Different playback options
AUX input, Electrical socket 12 V
The disc can be played back in different ways,
scroll with the navigation buttons to select
playback option.
The input allows you to connect other equipment. Always follow the instructions included
with the external equipment, or from the manufacturer or reseller, when connecting. Equipment connected via the RSE AUX input can use
the screens, wireless headphones, headphones sockets and the car's speakers.
When the dialogue box appears:
1. Press the right-hand navigation button to
move over in the right-hand menu.
2. Scroll using the navigation buttons to
select playback options.
``
* Option/accessory, for more information, see Introduction.
267
10 Infotainment system
RSE - Rear Seat Entertainment system - Dual Screen*
System
Connecting the RSE AUX input
Formats supported by the system.
10
Audio
format
CD-DA, DVD Audio Playback,
MP3, WMA
Video
format
DVD video, VCD, SVCD, DivX/
MPEG-4, WMA video, Photo CD
Kodak, Photo CD JPG
Disc
format
DVD-RAM, DVD-ROM, DVD-RW,
DVD+RW, DVD-R, DVD+R, CD-R,
CD-ROM, CD-RW, CD-3, HDCD
Changing the battery in the remote
control and wireless headphones
The remote control and headphones are powered by 2 AAA batteries.
Take along extra batteries for a long journey.
Advanced system settings
The RSE-AUX input is located in the centre console under the DVD player.
1. Connect the video cable to the yellow
socket.
2. Connect the left-hand audio cable to the
white socket and the right-hand one to the
red socket.
3. Connect the power cable to the power
socket if your equipment is designed for
12 V.
These settings can only be accessed when the
DVD player is empty.
Press MEDIA MENU.
GENERAL SETUP
AUDIO SETUP
ANGLE MARK
CAPTION
Remote control
COMPRESSION
1. Unscrew the screw and detach the battery
cover.
DVX(R)
REGISTRATION
PREFERENCES
TV TYPE
AUDIO
SUBTITLE
DEFAULTS
268
* Option/accessory, for more information, see Introduction.
G031359
G015700
2. Remove the used batteries, turn the new
batteries in accordance with the symbols
in the battery compartment and insert
them.
3. Fit the cover and screw in the screw.
10 Infotainment system
RSE - Rear Seat Entertainment system - Dual Screen*
Environmental care
10
G030395
Be sure to dispose of the exhausted batteries
in an environmentally safe manner.
Wireless headphones
1. Unscrew the screw and detach the battery
cover.
2. Remove the used batteries, turn the new
batteries in accordance with the symbols
in the battery compartment and insert
them.
3. Fit the cover and screw in the screw.
NOTE
If the system is too hot to be used or if battery voltage is too low then an information
message appears on the screen.
* Option/accessory, for more information, see Introduction.
269
Type designation...................................................................................
Dimensions and weights.......................................................................
Engine specifications............................................................................
Engine oil...............................................................................................
Fluids and lubricants.............................................................................
Fuel.......................................................................................................
Catalytic converter................................................................................
Electrical system ..................................................................................
Type approval ......................................................................................
Symbols in the display..........................................................................
270
272
274
276
277
279
281
283
284
286
287
SPECIFICATIONS
11 Specifications
Type designation
11
272
11 Specifications
Type designation
Knowing the car's type designation, vehicle
identification and engine numbers can facilitate all contact with an authorised Volvo dealer
regarding the car and when ordering spare
parts and accessories.
Type designation, vehicle identification
number, maximum permissible weights,
codes for colour and upholstery and type
approval number. The label is visible when
the right rear door is opened.
NOTE
The labels shown in the owner's manual are
not provided as exact reproductions of
those in the car. The purpose is to show
their approximate appearance and location
in the car. The information that applies to
your car in particular is available on the label
in question in your car.
11
Engine code, component and serial numbers.
Label for engine oil.
Gearbox type designation and serial number:
automatic gearbox AW
manual gearbox
automatic gearbox
Label for parking heater.
VIN number (type and model year designation plus chassis number).
Further information on the car is presented in
the registration document.
273
11 Specifications
Dimensions and weights
Dimensions
11
274
Dimensions
mm
Weights
H
Rear track
1624
Kerb weight includes the driver, the fuel tank
90% full and all fluids.
4807
I
Load width, floor
1064
Load length, floor, folded
seat
2018
J
Width
1898
K
Load length, floor
1118
Width including door mirrors
2112
D
E
Height
1784
F
Load height, floor
G
Front track
Dimensions
mm
A
Wheelbase
2857
B
Length
C
872
1634
The weight of passengers and accessories,
and towball load (when a trailer is hitched, see
table) influences the payload and is not
included in the kerb weight.
Permitted maximum load = Gross vehicle
weight - Kerb weight.
11 Specifications
Dimensions and weights
NOTE
WARNING
The documented kerb weight applies to
cars in the standard version - i.e. a car without extra equipment or accessories. This
means that for every accessory added the
loading capacity of the car is reduced correspondingly by the weight of the accessory.
The car's driving characteristics change
depending on how heavily it is loaded and
how the load is distributed.
For decal location, see page 272.
Max. total weight
Max. train weight (car+trailer)
Max. front axle load
Max. rear axle load
11
Equipment level
Examples of accessories that reduce loading capacity are the Kinetic/Momentum/
Summum equipment levels, as well as other
accessories such as Towbar, Load carriers,
Space box, Audio system, Auxiliary lamps,
GPS, Fuel-driven heater, Safety grille, Carpets, Cargo cover, Power seats, etc.
Max. load: See registration document.
Maximum roof load: 100 kg
Weighing the car is a certain way of ascertaining the kerb weight of your own particular car.
Towing capacities and towball load
Model
Max. weight braked trailer, kg
Max. towball load, kg
D3 FWD
1800
90
miscellaneous
2250
90
Max. weight unbraked trailer, kg
Max. towball load, kg
750
50
275
11 Specifications
Engine specifications
11
A
B
276
Engine
Engine
codeA
Output
(kW/
rpm)
Output
(hp/rpm)
Torque
(Nm/
rpm)
No. of
cylinders
Bore (mm)
Stroke
(mm)
Swept volume (litres)
Compression
ratio
2.5T
B5254T2
154/4980
210/5000
320/15004500
5
83
93.2
2.52
9.0:1
3.2
B6324S5
175/6200
238/6200
320/3200
6
84
96
3,19
10.8:1
V8
B8444S
232/5850
315/5850
440/3900
8
94
79.5
4,41
10.4:1
D5
D5244T4
136/4000
185/4000
400/20002760
5
81
93.2
2.40
17.3:1
D3B
D5244T5
120/4000
163/4000
340/17502750
5
81
93.2
2.40
17.3:1
Engine code, component and serial number can be read on the engine, see page 272.
Certain markets
11 Specifications
Engine oil
Adverse driving conditions
Check the oil level more frequently for long
journeys:
•
•
•
•
towing a caravan or trailer
in mountainous regions
at high speeds
in temperatures colder than -30 °C or hotter than +40 °C.
This can produce abnormally high oil temperature or oil consumption.
Also check the oil level more often if the car is
often driven short distances (less than 10 km)
when temperatures are low (below +5 °C).
Choose a fully synthetic engine oil for adverse
driving conditions. It provides extra protection
for the engine.
Volvo recommends Castrol oil products.
Viscosity chart
IMPORTANT
In order to fulfil the requirements for the
engine's service intervals all engines are
filled with a specially adapted synthetic
engine oil at the factory.The choice of oil has
been made very carefully with regard to
service life, starting characteristics, fuel
consumption and environmental impact.
11
An approved engine oil must be used in
order that the recommended service intervals can be applied. Only use a prescribed
grade of oil for both filling and oil change,
otherwise you will risk affecting service life,
starting characteristics, fuel consumption
and environmental impact.
Volvo Car Corporation disclaims all warranty liability if engine oil of the prescribed
grade and viscosity is not used.
``
277
11 Specifications
Engine oil
Oil decal
11
A
278
Engine variant
Engine code
2.5T
B5254T2
3.2
B6324S5
V8
Filling volume between MIN–
MAX (litres)
Volume, incl. oil filter
Oil grade: ACEA A5/B5
1.2
5.5
Viscosity: SAE 0W–30.
1.2
6.8
B8444S
1.2
6.7
D5
D5244T4
1.0
5.9
D3A
D5244T5
1.0
5.9
Certain markets
Recommended oil grade
(litres)
11 Specifications
Fluids and lubricants
Manual gearbox
Volume (litres)
M66
Prescribed transmission fluid
1.9
Automatic gearbox
BOT 350M3
Volume (litres)
TF-80SC
Prescribed transmission fluid
7.0
11
JWS 3309
Fluids
Fluid
System
Coolant
2.5T
8.0
3.2
9.7
V8
10.2
D3 and D5
12.5
Refrigerant
Air conditioning
Volume (litres)
B
Recommended oil grade
Coolant recommended by Volvo mixed
with 50% waterA, see the packaging.
The thermostat starts opening at:
90 °C in petrol engines and at 82 °C in
diesel engines
R134a (HFC134a)
Oil: PAG
Brake fluid
Brake system
0.6
DOT 4+
Power steering fluid
Power steering
1.0
of which reservoir
0.2
WSS M2C204-A or equivalent product
with the same specification.
Washer fluid
6.5
Use a washer antifreeze recommended
by Volvo, mixed with water for temperatures below freezing.
``
279
11 Specifications
Fluids and lubricants
11
A
B
Fluid
System
Fuel
Petrol engine
approx. 80
Petrol: see page 134
Diesel engine
approx. 68
Diesel: see page 134
Recommended oil grade
Water quality must fulfil the standard STD 1285.1.
Refrigerant quantity varies depending on engine variant. Volvo recommends that you contact an authorised Volvo workshop for the correct information.
IMPORTANT
The recommended transmission fluid must
be used to prevent damage to the gearbox.
Do not mix with any other transmission fluid.
If the transmission is topped up with a different fluid, contact a workshop nearby for
servicing. Volvo recommends that you contact the nearest authorised Volvo workshop.
NOTE
Under normal driving conditions the gearbox oil does not need changing during its
service life. However, it may be necessary
under adverse driving conditions, see
page 277.
280
Volume (litres)
11 Specifications
Fuel
CO2 emissions and fuel consumption
A
A
B
B
C
2.5T AWD
381 (385)A
16,0 (16,2)A
220 (222)A
9,2 (9,3)A
280 (282)A
11.7 (11.8)A
3.2 AWD
374 (377)A
16,1 (16,1)A
203 (208)A
8,7 (8,9)A
265 (269)A
11,4 (11,5)A
V8 AWD
472 (476)A
19,8 (20,0)A
230 (234)A
9,6 (9,8)A
317 (322)A
13.3 (13.5)A
D3 FWD
294 (294)A
11,1 (11,1)A
184 (184)A
7,0 (7,0)A
224 (224)A
8,5 (8,5)A
D5 AWD
280 (283)A
10,6 (10,7)A
180 (182)A
6,8 (6,9)A
217 (219)A
8.2 (8.3)A
D5 AWD
294 (294)A
11,1 (11,1)A
184 (184)A
7,0 (7,0)A
224 (224)A
8,5 (8,5)A
D3 AWDB
280 (283)A
10,6 (10,7)A
180 (182)A
6,8 (6,9)A
217 (219)A
8.2 (8.3)A
D3 AWDB
294 (294)A
11,1 (11,1)A
184 (184)A
7,0 (7,0)A
224 (224)A
8,5 (8,5)A
11
The value in brackets applies to the variant seating seven.
Certain markets
A = urban driving (l/100 km)
C = combined driving (l/100km)
B = driving on main roads (l/100 km)
``
281
11 Specifications
Fuel
Fuel consumption and emissions of
carbon dioxide
11
Fuel consumption and emission values in the
table above are based on specific EU cycles1,
that apply to cars with kerb weight in the basic
version and without extra equipment. The car's
weight may increase depending on equipment.
This, as well as how heavily the car is loaded,
increases fuel consumption and carbon dioxide emissions.
There are several reasons for increased fuel
consumption compared with the table's values. Examples of this are:
• The driver's driving style
• High speed results in increased wind resistance
• AC switched on (air conditioning)
• Roof load and ski box result in increased
wind resistance
• Too low air pressure in the tyres
• Fuel quality, road and traffic conditions,
weather and the condition of the car.
To bear in mind
Large deviations in fuel consumption may arise
in a comparison with the EU driving cycles1
which are used in the certification of the car
and on which the consumption figures in the
table are based. Below are examples of tips
that the driver can use in order to reduce consumption:
• Drive gently.
• Drive in the highest gear possible, adapted
to the traffic situation and the road you are
driving on. Lower engine speeds result in
lower fuel consumption.
• Use engine braking to slow down, when it
can take place without risk to other road
users.
• Avoid letting the engine idle for long periods. Pay attention to local traffic regulations. Switch off the engine if stationary for
longer periods, when this can take place
without endangering other road users.
• If the car is equipped with an electric
engine block heater, always use it before
starting from cold.
• Drive with the correct air pressure in the
tyre pressure for best results, see the tyre
pressure table on page 178.
• Choice of tyres can affect fuel consumption. Information on suitable tyres can be
given by your dealer.
• Extra weight - remove unnecessary items
from the car.
• Remove the space box directly after use.
• Always carry out service and maintenance
on the car in accordance with the instructions in the owner's manual.
Even a combination of some of the abovementioned examples can result in significantly
improved consumption.
For further information, please refer to the regulations referred to in accordance with the
above.
WARNING
Never switch off the engine while moving,
such as downhill, this deactivates important
systems such as the power steering and
brake servo.
tyres and check this regularly. Select ECO
See page 134 for general information on fuel.
1
282
Official fuel consumption figures are based on two standardised driving cycles in a laboratory environment ("EU driving cycles") all in accordance with EU Directive 80/1268/EEC (Euro 4), EU Regulation
no 682/2008 (Euro 5) and UN ECE Regulation no 101. The regulations cover the driving cycles for city driving and driving on main roads. - City driving - the measurement starts with cold starting
the engine. The driving is simulated. - Driving on main roads - the car is accelerated and braked at speeds between 0-120 km/h. The driving is simulated. The value for combined driving, which is
reported in the table, is a combination of city driving and driving on main roads, in accordance with legal requirements. CO2 emissions - the exhaust gases are collected in order to calculate the
carbon dioxide emissions during the two driving cycles. These are then analysed and give the value for CO2 emissions.
11 Specifications
Catalytic converter
General
The purpose of the catalytic converter is to
purify exhaust gases. It is located in the flow of
exhaust gases close to the engine so that it
quickly reaches operating temperature. The
catalytic converter consists of a monolith
(ceramic or metal) with channels. The channel
walls are lined with a thin layer of platinum,
rhodium and palladium. These metals act as
catalysts, i.e. they participate in and accelerate
a chemical reaction without being used up
themselves.
11
Lambda-sondTM oxygen sensor
The Lambda-sond is part of a control system
intended to reduce emissions and improve fuel
economy.
An oxygen sensor monitors the oxygen content
of the exhaust gases leaving the engine. This
value is fed into an electronic system that continuously controls the injectors. The ratio of fuel
to air directed to the engine is continuously
adjusted. Together with the three-way catalytic
converter, these adjustments create optimal
conditions for efficient combustion of the
harmful emissions (hydrocarbons, carbon
monoxide and nitrous oxides).
283
11 Specifications
Electrical system
General
12 volt system with a voltage-regulated alternator. Single pole system in which the chassis
and engine block are used as conductors.
11
Battery
Engine
A
Voltage, V
Cold start capacity,
Reserve capacity,
CCA (Cold Cranking Amperes), A
minutes
Capacity, Ah
2.5T, 3.2, V8
12
600–800 A
120–150
70–90
D5
12
800
150
90
Output W
Socket
Main beam/dipped beam halogen
55
H7
Main beam, cars with Active Xenon
65
H9
Active Xenon
35
D1S
Fog lamp, front
55
H1
Front direction indicators
21
BAW9s
Cars with a parking heater have 800 A
If the battery is changed, replace it with a battery of the same cold start capacity and reserve
capacity as the original (see the decal on the
battery).
Bulbs
Lighting
284
11 Specifications
Electrical system
Lighting
Output W
Socket
Position lamps front/rear, parking lamps front, side marker lamps front, number plate
lighting, courtesy lighting rear
5
W 2.1 x 9.5d
Rear fog lamp
21
BAY9s
Brake lamp, reversing lamp
21
BA15S
Rear direction indicators
21
BAU15s
Vanity mirror
1.2
SV5.5
Front courtesy lighting, cargo area lighting
5
SV8.5
Glovebox lighting
3
BA9
11
285
11 Specifications
Type approval
Remote control system
Country
11
A, B, CY, CZ, D, DK,
E, EST, F, FIN, GB,
GR, H, I, IRL, L, LT,
LV, M, NL, P, PL, S,
SK, SLO
IS, LI, N, CH
HR
Delphi hereby
certifies that this
remote control key
system conforms to
the essential characteristic requirements and other relevant regulations of
directive 1999/5/EC.
RC
ETC093LPD0155
286
11 Specifications
Symbols in the display
General
There are a variety of different symbols in the
display in the car. The symbols are divided into
warning, indicator and information symbols.
Shown below are the most common symbols
with their meanings and a reference to where
in the manual further information can be found.
For more information on symbols and text
messages, see pages 51 and 54.
illuminates
The red warning symbol
when a fault has been indicated which could
affect the safety and/or driveability of the car.
An explanatory text is shown on the information display at the same time.
illumiThe yellow information symbol
nates, in combination with text in the information display, when a deviation in any of the car's
systems has occurred. The yellow information
symbol can also illuminate in combination with
other symbols.
Symbols in the display
Symbol
Indicator and warning symbols in the
combined instrument panel
Symbol
Meaning
Page
Warning
21, 51,
53, 150,
151
Emissions system
Page
Engine preheater
(diesel)
53
Indicator symbol
for trailer
53
Parking brake
applied
53
Airbags - SRS
21, 53
Low oil pressure
51, 52
Seatbelt reminder
18, 52
11
51, 53
Fault in the ABS
system
52, 147
Rear fog lamp
53
Stability system,
STC or DSTC
Meaning
53, 150
``
287
11 Specifications
Symbols in the display
Symbol
11
Meaning
Page
Alternator not
charging
53
Symbol
52, 147
Meaning
Page
Audio files
246
Directory in CD
disc
246
Traffic information
242, 244
G021220
Fault in brake system
Information symbols in the centre
console display
Other information symbols in the
combined instrument panel
Symbol
288
Meaning
Page
Cruise control*
65
Information symbol in rearview mirror
Symbol
* Option/accessory, for more information, see Introduction.
Meaning
Page
Airbag, passenger seat, deactivated
25
11 Specifications
11
289
12 Alphabetical Index
A
ABS fault.................................................... 52
Active Xenon headlamps..................... 56, 59
Adaptive system...................................... 144
Additional heater........................................ 92
Adjusting headlamp pattern.................... 168
halogen headlamp.............................. 168
12
Adjusting the steering wheel...................... 68
AF – automatic frequency update........... 244
Airbag
activating/deactivating, PACOS........... 24
driver's and front passenger side......... 23
key switch off........................................ 24
AIRBAG ..................................................... 22
Airbag system............................................ 22
127
128
127
128
128
127
127
trailer................................................... 160
W button............................................. 144
Automatic locking.................................... 122
AUX.......................................................... 236
Auxiliary lamps........................................... 56
Average fuel consumption......................... 61
AWD, All-wheel drive............................... 146
All-wheel drive, AWD............................... 146
Audio
headphones socket............................ 235
surround............................................. 239
B
Audio, see also Sound............................. 233
Backrest
front seat, lowering............................... 96
Audio files................................................ 246
Audio system
functions............................................. 236
Air conditioning.......................................... 84
ECC...................................................... 88
rear of passenger compartment........... 55
Audio volume
phone.......................................... 251, 261
phone/media player............................ 261
ring signal, phone............................... 261
Air distribution............................................ 85
Auto, ECC.................................................. 89
Air distribution, A/C................................... 89
Automatic car washes............................. 190
Air quality system, ECC............................. 88
Automatic gearbox.......................... 143, 144
Lock-up function................................ 144
safety systems.................................... 145
towing and recovery........................... 157
Air vents
instrument panel................................... 85
290
Alarm
alarm indicator....................................
alarm signals.......................................
arming.................................................
automatic alarm activation.................
deactivating a triggered alarm............
disarming............................................
general................................................
Backrest rear seat, lowering.................... 108
Bag holder............................................... 115
Bass speaker........................................... 239
Battery............................................. 209, 284
maintenance............................... 199, 209
overload.............................................. 133
specifications...................................... 284
start assistance................................... 159
symbols on the battery....................... 209
Blind spot (BLIS)...................................... 153
Blind Spot Information System, BLIS 56, 153
12 Alphabetical Index
Bluetooth
handsfree............................................ 259
mute microphone............................... 261
transfer call to mobile......................... 261
Boarding
rear seat.............................................. 108
Bonnet..................................................... 201
Bonnet, opening...................................... 201
Booster cushion
folding up.............................................. 39
lowering................................................ 40
Booster cushion, integrated...................... 39
Bottle holder for rear seat passengers.... 104
Brakes
anti-lock braking system, ABS........... 147
Brake system........................................... 147
Bulbs, see Lighting.......................... 211, 284
C
Calls
functions during a call........................ 253
incoming............................................. 260
operation............................................. 260
Car care, leather upholstery.................... 192
Cargo area...............................................
bag holder...........................................
cargo area compartment....................
cargo cover.........................................
electrical socket..................................
lighting................................................
loading................................................
safety grille..........................................
safety net............................................
111
115
116
115
115
101
112
114
113
Cargo area compartment........................ 116
Cargo cover............................................. 115
Car upholstery......................................... 192
Car wash.................................................. 190
Catalytic converter........................... 137, 283
recovery.............................................. 158
CD
changer............................................... 246
location in the car, table....................... 34
safety.................................................... 33
Child safety locks...................................... 55
Child seats.................................................
extra locking function in seatbelt..........
ISOFIX fixture system for child seats. . .
recommended......................................
upper mounting points for child seats..
33
41
40
34
41
Cigarette lighter socket.............................. 56
Clock, setting............................................. 49
Clutch fluid, checking & topping up........ 206
CD functions............................................ 246
Coat hanger............................................. 104
Checking and topping up the coolant..... 205
Cold start
automatic gearbox.............................. 144
Children..................................................... 33
child safety locks.................... 40, 55, 125
child seats and airbags......................... 33
child seats and side airbags................. 26
location in the car................................. 33
12
Cleaning
automatic car washes......................... 190
car wash............................................. 190
rims..................................................... 190
seatbelts..................................... 192, 193
upholstery........................................... 192
water-repellent surface......................... 75
Collision
inflatable curtain, IC.............................. 28
Colour code, paint................................... 194
Combined instrument panel...................... 49
Car care................................................... 190
291
12 Alphabetical Index
Compass................................................... 71
calibration............................................. 74
setting the zone.................................... 71
Cruise control............................................ 65
Driving
cooling system....................................
economical.........................................
in water...............................................
slippery driving conditions..................
with the tailgate open.........................
with trailer...........................................
Cup holder....................................... 104, 105
Driving in water........................................ 133
D
Driving with a trailer
towball load........................................ 274
towing capacity.......................... 160, 274
Condensation in headlamps.................... 190
Cooler box............................................... 107
Cooling system........................................ 132
12
132
132
133
132
132
160
Electrical socket
cargo area........................................... 115
centre console...................................... 56
rear seat................................................ 68
Electrical system...................................... 284
Emergency calls...................................... 250
Emergency equipment
warning triangle.................................. 179
Emergency puncture repair..................... 184
Emission control
fault indicator........................................ 53
Engine compartment............................... 202
Deadlocks
temporary deactivation....................... 124
temporary deactivation of the alarm
detectors............................................. 128
DSTC, see also Stability control system..................................................... 53, 149
operation............................................. 149
Defroster.................................................... 90
Detectors................................................... 56
E
Diesel....................................................... 137
ECC, electronic climate control........... 84, 88
Engine oil......................................... 203, 277
adverse driving conditions.................. 277
capacities........................................... 277
changing............................................. 203
filter..................................................... 203
oil grade.............................................. 277
oil pressure........................................... 52
Diesel: engine preheater............................ 53
Economical driving.................................. 132
Engine preheater....................................... 53
Diesel particle filter.................................. 138
ECO pressure.......................................... 177
table.................................................... 178
Engine specifications............................... 276
Direction indicators.................................... 60
Display, messages..................................... 54
Dolby Surround Pro Logic II.................... 232
Door mirrors............................................... 74
292
Driver's door control panel.................. 48, 69
Environmental labelling, FSC, owner's
manual....................................................... 15
EON - Enhanced Other Networks............ 245
Equalizer.................................................. 239
12 Alphabetical Index
Expectant mothers, seatbelt...................... 19
FSC, environmental labelling..................... 15
External audio source
AUX-socket......................................... 236
USB connection.................................. 237
Fuel
fuel consumption, display..................... 61
fuel economy...................................... 177
fuel filter.............................................. 138
parking heater....................................... 91
refuelling............................................. 134
External dimensions................................ 274
F
Fan
ECC...................................................... 90
First aid equipment.................................. 181
Floor mats.................................................. 97
Fluids, capacities..................................... 279
Fuses.......................................................
box in cargo area................................
box in cargo area - Executive.............
box in passenger compartment..........
box in the engine compartment..........
changing.............................................
end box...............................................
general................................................
218
226
228
224
220
218
222
218
Fluids and oils.................................. 203, 279
Fluids and oils, checks, engine compartment......................................................... 204
G
H
Hazard warning flashers............................ 57
Headlamp levelling.................................... 58
Headlamp pattern, adjusting................... 168
Headlamp pattern adjustment
Active Bending Lights (ABL) .............. 168
Headlamps
ABL....................................................... 59
off/on.................................................... 58
Headlamp washers.................................... 64
Headphones socket................................. 235
Head restraint
centre seat, rear.................................. 109
Heater
fuel-driven............................................. 91
Fog lamp
front...................................................... 59
Gearbox
automatic............................................ 143
manual................................................ 142
Heating
front seats............................................. 57
rearview and door mirrors.............. 57, 90
rear window.................................... 57, 90
Fog lamps
rear........................................................ 59
General information on fuel..................... 136
High-pressure headlamp washing............. 64
Glovebox................................................. 103
HomeLinkŸ ................................................ 78
Gross vehicle weight............................... 274
Home safe lighting
setting................................................... 60
Fluids and oils general............................. 199
Front seat
lumbar................................................... 99
massage............................................... 99
12
293
12 Alphabetical Index
I
K
Ignition keys............................................. 141
Kerb weight.............................................. 274
IMEI number............................................ 255
Immobiliser...................................... 120, 141
Key........................................................... 120
remote control key.............................. 120
Inflatable Curtain........................................ 28
Keypad in the steering wheel............ 65, 234
Information display.................................... 54
Kick-down
automatic gearbox.............................. 145
Infotainment system................................ 232
12
Instrument lighting..................................... 59
Instrument overview
left-hand drive....................................... 44
right-hand drive.................................... 46
L
Integrated booster cushion........................ 39
Lamps, see Lighting................................ 211
Interior lighting......................................... 100
Leather upholstery, washing instructions 192
Interior rearview mirror............................... 71
automatic dimming............................... 71
Lighting.................................................... 211
Active Xenon headlamps................ 56, 59
automatic lighting, dipped beam.......... 58
automatic lighting, passenger compartment.................................................... 101
bulbs, specifications........................... 284
cargo area........................................... 101
exterior.................................................. 58
headlamp levelling................................ 58
home safe lighting................................ 60
in passenger compartment................. 100
instrument lighting................................ 59
Intermittent wiping..................................... 63
ISOFIX fixture system for child seats......... 40
J
Jack......................................................... 180
294
Lambda-sond.................................. 137, 283
lighting panel, passenger compartment...................................................... 58
main/dipped beam............................... 58
position/parking lamps......................... 58
reading lamps..................................... 100
rear fog lamp........................................ 59
switching headlamp pattern right/lefthand traffic, ABL........................... 56, 168
Lighting, bulb replacement......................
bulb location front lamp......................
cargo area...........................................
courtesy lighting.................................
dipped beam halogen.........................
direction indicators.............................
fog lamp..............................................
front....................................................
lamp housing, rear..............................
main beam..........................................
main beam halogen............................
number plate lighting..........................
parking lamps.....................................
position lamps....................................
rear fog lamp......................................
side marker lamps..............................
vanity mirror........................................
211
212
217
216
212
213
213
211
214
212
212
216
213
213
216
213
217
Loading
cargo area........................................... 112
general........................................ 110, 112
12 Alphabetical Index
load capacity...................................... 110
load carriers........................................ 110
roof load............................................. 110
Master key............................................... 120
Load on the roof...................................... 110
Menu structure
audio system...................................... 248
phone, menu options.......................... 257
phone, overview................................. 256
Locking/unlocking
glovebox.............................................
inside..................................................
outside................................................
tailgate................................................
123
123
122
123
Lubricants................................................ 279
Lubricants, capacities.............................. 279
M
Main and dipped beam
switching............................................... 60
Main beam "flash"..................................... 60
Maintenance............................................ 199
rustproofing........................................ 195
self-maintenance................................ 199
Making calls............................................. 260
Manual gearbox....................................... 142
towing and recovery........................... 157
Massage
front seat............................................... 99
Menus
audio system...................................... 234
Messages in BLIS.................................... 155
Messages in the information display......... 54
Meters in the combined instrument panel
fuel gauge.............................................
outside temperature gauge..................
speedometer.........................................
tachometer...........................................
trip meter..............................................
49
49
49
49
49
Misting....................................................... 84
condensation in headlamps............... 190
rear window.......................................... 57
removing with defroster function.......... 90
Mobile phone
connect............................................... 262
handsfree............................................ 259
register phone..................................... 260
Mp3 functions.......................................... 246
N
News................................................ 241, 244
O
Oil, see also Engine oil....................... 52, 277
One-key dial............................................. 253
Owner's manual, environmental labelling.. 15
12
Oxyhydrogen gas.................................... 159
P
PACOS....................................................... 24
PACOS, switch.......................................... 24
Paintwork
colour code......................................... 194
damage and touch-up........................ 194
Panel vents in the door pillar..................... 86
Parking assistance............................. 56, 151
parking assistance sensors................ 152
Parking brake....................................... 53, 67
Multi-filter........................................... 84, 138
MY KEY................................................... 234
295
12 Alphabetical Index
Parking heater
battery and fuel.....................................
general..................................................
symbols and display messages............
time setting...........................................
92
91
91
92
Parking lamps............................................ 58
Petrol grade............................................. 136
12
296
Phone
call volume.......................................... 254
connect............................................... 262
controls............................................... 250
ending a call....................................... 252
handsfree............................................ 259
incoming calls..................................... 260
last dialled numbers........................... 253
making calls................................ 252, 260
memory............................................... 254
messages........................................... 255
on/off.................................................. 251
one-key dial........................................ 253
phone book................................. 254, 262
phone book, shortcut......................... 262
privacy handset.................................. 252
receiving a call............................ 252, 261
register phone..................................... 260
shortcuts............................................. 251
SIM card............................................. 252
traffic safety........................................ 252
volume reduction during phone call... 251
Phone book............................................. 254
Phone system.......................................... 249
Pinch protection, sunroof.......................... 77
Polishing.................................................. 191
Position lamps........................................... 58
Power seat................................................. 97
Power steering fluid, checking and topping
up............................................................. 206
Power sunroof........................................... 76
Power windows.........................................
blocking................................................
passenger seat.....................................
rear seat................................................
69
70
70
70
frequency update................................ 244
news........................................... 241, 244
PTY..................................................... 242
radio settings...................................... 240
radio stations...................................... 240
radio text............................................. 242
regional............................................... 244
storing stations................................... 240
traffic information................................ 242
tuning.................................................. 241
volume control, programme types..... 241
Radio functions........................................ 240
Radio text................................................ 242
Rain sensor................................................ 63
Random, CD and audio files.................... 247
PTY – Programme type........................... 242
RDS functions.......................................... 241
resetting.............................................. 245
Puncture, see Tyres......................... 180, 182
Reading lamps......................................... 100
Rear centre console, removal.................. 108
R
Radio
alarm................................................... 242
AUTOSTORE...................................... 240
EON.................................................... 245
Rear seat
boarding............................................. 108
Rear seat, lowering.................................. 108
Rearview and door mirrors
compass............................................... 71
door...................................................... 74
electrically retractable........................... 74
12 Alphabetical Index
heating.................................................. 57
interior................................................... 71
retractable............................................. 55
Roof load................................................. 110
Side airbag, SIPS....................................... 26
ROPS (Roll Over Protection System)......... 31
SIM card.................................................. 252
double................................................. 255
Rear window, defrosting............................ 57
ROPS (Roll Over Protection System) (Rollover protection).......................................... 31
Recirculation
ECC...................................................... 89
Rustproofing............................................ 195
SIPS bag – decal....................................... 26
SIPS bags.................................................. 26
Sliding seat.............................................. 108
Refrigerant................................................. 84
S
SMS......................................................... 255
write.................................................... 255
Safety grille.............................................. 114
Soot filter........................................... 54, 138
REG - Regional radio programmes......... 244
Safety net................................................. 113
Soot filter full............................................ 138
Relay/fuse box: see Fuses....................... 218
Scan
radio stations...................................... 241
Sound
audio settings............................. 233, 238
audio source............................... 233, 236
Refuelling
fuel cap............................................... 136
refuelling............................................. 136
Remote control........................................ 120
replacing the battery........................... 121
Remote control, HomeLinkŸ
programmable ..................................... 78
Seatbelt
pregnancy............................................. 19
Seatbelt reminder...................................... 19
Remote control key
functions............................................. 120
Seatbelts.................................................... 18
seatbelt tensioner................................. 19
Remote control key system, type approval............................................................ 286
Rims
cleaning.............................................. 190
Seats
heating.................................................. 57
lowering the front backrest................... 96
lowering the rear backrest.................. 108
manual setting...................................... 96
power seat............................................ 97
RND – Random........................................ 247
Service programme................................. 198
Retractable power door mirrors (option). . . 55
12
Spare wheel............................................. 180
temporary spare................................. 179
Speed dial numbers................................. 253
Spin control............................................. 149
Spin Control............................................. 149
Spin control function............................... 149
SRS system
general.................................................. 22
Stability system....................................... 149
deactivating/activating....................... 149
Roll-over protection................................... 31
297
12 Alphabetical Index
indicator................................................ 53
symbols.............................................. 149
Switching
main and dipped beam......................... 60
Stains....................................................... 192
Symbols
indicator symbols................................. 52
stability system................................... 149
warning symbols................................... 51
Standby mode, phone............................. 251
Start assistance....................................... 159
12
Towing eye.............................................. 157
TP – Traffic information.................... 242, 244
Starting the engine.................................. 140
Traction control system........................... 149
Steering lock............................................ 140
Traffic information............................ 242, 244
Steering wheel
cruise control........................................ 65
keypad.......................................... 65, 234
steering wheel adjustment.................... 68
Stone chips and scratches...................... 194
Storage compartment...................... 105, 106
Storage spaces in the passenger compartment......................................................... 102
Storing radio stations............................... 240
Subwoofer............................................... 239
Sunroof......................................................
opening and closing.............................
pinch protection....................................
sunscreen.............................................
ventilation position................................
298
installation........................................... 164
removing............................................. 166
specifications...................................... 163
76
76
77
77
76
T
Tailgate
driving with open tailgate................... 132
locking/unlocking................................ 120
open...................................................... 68
Technical data, engine............................. 276
Temperature
actual temperature............................... 84
Temperature control.................................. 90
Tools........................................................ 180
Towbar............................................. 160, 164
Towbar, see Towing equipment.............. 162
Towing..................................................... 157
towing eye.......................................... 157
Sunscreen, sunroof.................................... 77
Towing capacity............................... 160, 274
Surround.................................................. 239
Towing equipment................................... 160
general........................................ 160, 162
Trailer....................................................... 160
cable................................................... 162
driving with a trailer............................ 160
Trip computer............................................ 61
Type approval, remote control key system........................................................... 286
Type designation..................................... 272
Tyres
direction of rotation............................ 176
driving characteristics......................... 174
general................................................ 174
maintenance....................................... 174
pressure...................................... 177, 178
puncture repair................................... 184
specifications...................................... 174
speed ratings...................................... 174
tread wear indicators.......................... 175
winter tyres......................................... 176
12 Alphabetical Index
U
USB, connection...................................... 237
Weights
kerb weight......................................... 274
trailer weight....................................... 160
Vibration damper..................................... 162
Wheels
changing.............................................
installation...........................................
removal...............................................
snow chains........................................
spare wheel........................................
Volume control......................................... 236
Whiplash injury.......................................... 29
V
Ventilation fan function.............................. 84
W
182
183
182
176
180
12
WHIPS
child seat/booster cushion................... 29
whiplash injury...................................... 29
Windscreen washing.................................. 64
Warning lamp
stability and traction control system. . 149
Warning symbol, airbag system................ 21
Warning triangle....................................... 179
Washers
headlamps............................................ 64
rear window.......................................... 64
washer fluid, filling.............................. 204
windscreen........................................... 64
Windscreen wipers.................................... 63
rain sensor............................................ 63
Winter tyres.............................................. 176
Wiper
rear window.......................................... 64
Wiper blades............................................
cleaning..............................................
replacing, rear window.......................
replacing, windscreen.........................
207
207
207
207
Water and dirt-repellent coating................ 75
Water-repellent surface, cleaning............ 191
Waxing..................................................... 191
299
12 Alphabetical Index
12
300
Kdakd8Vg8dgedgVi^dcIE&&-%,:c\a^h]!6I&%'%!Eg^ciZY^cHlZYZc!<ŽiZWdg\'%&%!8deng^\]i©'%%%"'%&%Kdakd8Vg8dgedgVi^dc
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement