5. How to Operate continued
Model:
3. Once the picture appears on the monitor, open the cover and make
the Zoom Adjustment by rotating the screw (NEAR-Anti-clockwise,
FAR-Clockwise) until you get the desired view. Next make the Focal
Adjustment by rotating the screw (TELE-Anti-clockwise, WIDE
Clockwise) until you get the desired view.
Colour
Image Sensor:
FULL D1 CCD
DSP:
Xvision DSP
Resolution:
650 TVL
Lens Viewing Angle:
30 to 64°
Minimum Illumination:
Audio:
Operating Voltage:
Suggested Power Supply:
Mounting:
Weatherproofing:
4. Tighten the two screws, then replace the dome cover.
Dimensions:
CCTV
XCD649
Picture Type:
IR Night Vision
Figure 4
CCTV
Specifications
No
0.009 Lux
No
Model: XCD649
650 TVL Dome Camera
12V DC 80mA
12V DC 1250mA
Wall/Ceiling
No
(WxHxD) 105 x 85 x 105mm
Before you begin
zzPlease unpack the box carefully and identify that all the parts are present.
zzThe camera is suitable for indoor or outdoor use. Please bear in mind the
following points when choosing a mounting position.
-- The camera must be positioned so that it will not point directly into the
sun (sunrise and sunset) or any bright light, as this may cause damage
to the camera.
-- Avoid viewing areas where half the area is in bright sunlight and the
other half is dark, such as in the shadow of a building. All types of
cameras have difficulty in ‘seeing’ with such a large lux level variation.
zzDo not cut the camera cables, this will void the warranty.
zzMake sure you use only the recommended power supply. Damage caused to
the camera by incorrect voltage or wiring is not covered by the warranty.
Model:
XCD649
650 TVL Dome Camera
Thank you for purchasing this Xvision camera. Before operating this
product, please read this instruction manual carefully.
3. Contents
4. Installation continued
1. Product Description
zzVery High Resolution CCD sensor provides great quality Colour
images in light levels of 0.009 lux and above.
zzDiscreet styling for unobtrusive low profile use.
zzTamper resistant and easy to clean as all moving parts are behind
the dome cover.
zzXvision Digital Signal Processing (DSP) and Full D1 CCD SENSOR
which has been optimised for internal viewing and features
Automatic Gain Control, Auto White Balance, Back Light
Compensation, Low Smear, Edge Enhancement and Zero Colour
Rolling.
4. Adjust the camera viewing angle by first tilting (STEP 1) then
rotating the camera module (STEP 2), and then turn the
horizontal adjustment ring (STEP 3) to correct the image and
achieve proper orientation (as shown in Figure 2).
XCD649 Camera
Screws & Wall Plugs
4. Installation
Camera
Module
Rotate
1. Connect the video output to the monitor or other video device
through a 75 Ohms type coaxial cable.
2. Connect the power source, insert the AC plug into the AC socket
and the DC plug into the DC Jack (+12V DC in jack centre).
Horizontal
Adjustment
Ring
DC Power
(to Power Source)
1. Select a suitable position on the
wall or ceiling to install the camera.
Depending on your installation
requirements you can either bring
the cables through the side entry or
the back entry of the housing.
Video Out
2. Features
ADJUSTING CAMERA VIEW
Tilt
The XCD649 Colour Varifocal Dome camera is designed for high risk
applications. It offers very high resolution 650 TVL images from its
Xvision DSP and Full D1 CCD sensor, and has an Xvision 4.0 to 9.0mm
Varifocal Lens which allows easy selection of the optimum viewing
angle required during installation. It will provide images in light levels
as low as 0.009 lux. The camera is designed for internal use and for
wall or ceiling mounting.
5. How to Operate
STEP 1
2. Rotate the dome housing
counterclockwise to remove it from
the camera housing.
Camera Module
Adjustment
3. Secure the camera in the desired
ceiling position with the four fixing
screws (as shown in Figure 1).
Rotate
STEP 2
(to Monitor or other video device)
STEP 3
Horizontal Ring
Adjustment
Figure 2
Figure 3
5. Place the dome cover on the camera and tighten it by turning it
clockwise.
zzOptional mirrored dome cover available.
Figure 1
">