TOYOTA PriusPrime 2017– TVIP V5 Prius 2016

TOYOTA PriusPrime 2017– TVIP V5 Prius 2016
TOYOTA
PriusPrime
Prius
PREPARATION
2017–
2016–
TVIP V5
RS3200 PLUS
Recommended Tools
Part Number: PT398-47160
Personal & Vehicle Protection
Conflicts
Description
Safety Glasses
Safety Gloves
(Optional)
Blankets, Parts Boxes
Special Tools
Recommended Sequence of Application
Item#
Quantity
Techstream
Description
Version 10.30.029 or later
Striker Tool
CAD-E IADS P/N ALL 02-016-01
Wiring Terminal Tool
CAD-E IADS P/N ALL 02-016-03
P/N 49YA000056
Installation Tools
Screwdriver
Kit Contents
Item#
Quantity
Nylon Panel Removal Tool
Description
1
1
V5 Wire Harness
2
1
GBS ECU Mounting Bracket
Pliers
Tape
Hardware Bag Contents
Quantity
Clear,
Electric
Utility Knife
1
2
1
GBS ECU Mounting Bracket
3
1
Foam Tape
4
20
Wire Ties
5
1
Vinyl Sheet
6
1
7
1
GBS Microphone
8
2
V5 Window Label English
9
2
V5 Window Label Spanish
10
1
V5 Owner’s Guide
GBS ECU
08190-0C820
Socket
10mm, extension
Special Chemicals
Cleaner
VDC Approved Cleaner
Legend
xx
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk
of injury.
CAUTION: : A process that must be carefully
observed in order to reduce the risk of damage
to the accessory/vehicle and to ensure a quality
installation.
TOOLS AND EQUIPMENT: Used in Figures calls
out the specific tools and equipment recommended for this process.
REVISION MARK: This mark highlights a change
in installation with respect to previous issue.
SAFETY TORQUE: This mark indicates that
torque is related to safety.
WIRE TIE LOCATION: Wire Tie location number.
xx
PREVIOUS WIRE TIE LOCATION: This mark
indicates a previously installed Wire Tie.
M6 Bolt
91651-60618
08192-6C810
00107-VIPWS
PT398-48142-AA
Additional Items Required For Installation
Quantity
Battery: 48 in•lbf (5.4 N•m), Bracket Bolt: 71 in•lbf (8 N•m),
Pick Tool
Description
1
Item#
e.g. Panel Pry Tool #1 Toyota
SST# 00002-06001-01
Side Cutters
Torque Wrench
Item#
#2 Phillips, Flat Blade Jeweler’s
Description
Accessory Installation Practice (read before installation)
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the “Accessory Installation Practices”
document.
This document covers such items as:
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.)
• Safety (eye protection, checking torque procedure, etc.)
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.)
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.)
Please see your Toyota dealer for a copy of this document.
Issue H : 11/22/16
Page 1 of 36
TOYOTA
PREPARATION
PriusPrime
Prius
2017–
2016–
TVIP V5
RS3200 PLUS
Table of Contents
I. Preparation............................................................................................................................... 1-5
1. Table of Contents.................................................................................................................................................2
2. Wire Routing Overview........................................................................................................................................3
3. Perform the Following..........................................................................................................................................5
II. Procedure............................................................................................................................... 7-31
1.
2.
3.
4.
5.
6.
7.
Preparation..........................................................................................................................................................7
Vehicle Disassembly............................................................................................................................................7
GBS ECU & V5 Harness Preparation and Installation.......................................................................................12
Microphone Installation......................................................................................................................................24
Registration........................................................................................................................................................27
Window Label Installation..................................................................................................................................31
Complete the Installation...................................................................................................................................31
III. Checklist............................................................................................................................... 32-36
1. Accessory Function Checks...............................................................................................................................32
2. Vehicle Function Check.....................................................................................................................................34
3. Vehicle Appearance Check................................................................................................................................35
Issue H : 11/22/16
Page 2 of 36
Wire Harness Outline
C
B
M
a
A’
D
E
A
1P White
A’
1P White
a
-
Sky Blue Wire
(Female Terminal)
B
-
2P White
C
-
2P Gray
D
2P White
E
8P White
M
2P White
(for GBS MIC)
X
2P White
(GBS MIC)
Y
GBS Microphone
Z
GBS ECU
2017–
2016–
Page 3 of 36
A
Description
PriusPrime
Prius
Z
Vehicle
TOYOTA
TVIP
PREPARATION
Issue H : 11/22/16
TOYOTA PriusPrime w/11in Display RS3200 PLUS
X
Y
TVIP V5
RS3200 PLUS
Wire Harness Outline
C
B
M
a
A’
D
E
A
1P White
A’
1P White
a
-
Sky Blue Wire
(Female Terminal)
B
-
2P White
C
-
2P Gray
D
2P White
E
8P White
M
2P White
(for GBS MIC)
X
2P White
(GBS MIC)
Y
GBS Microphone
Z
GBS ECU
2017–
2016–
Page 4 of 36
A
Description
PriusPrime
Prius
Z
Vehicle
TOYOTA
TVIP
PREPARATION
Issue H : 11/22/16
TOYOTA Prius and PriusPrime w/7in Display RS3200 PLUS
X
Y
TVIP V5
RS3200 PLUS
TOYOTA
PREPARATION
PriusPrime
Prius
2017–
2016–
TVIP V5
RS3200 PLUS
CAUTION: There are two Sensitivity Values for the GBS ECU.
You must first determine which Glass your vehicle has.
Perform the Following.
a. Roll down the Driver’s window partway.
b. Look at the edge of the window.
THIS VEHICLE HAS ACOUSTIC WINDOWS
You will need to use sections
highlighted in Grey for this Vehicle.
Issue H : 11/22/16
Page 5 of 36
THIS VEHICLE HAS UV WINDOWS
You will need to use sections
highlighted in GREEN for this Vehicle.
TOYOTA
PriusPrime
Prius
PREPARATION
2017–
2016–
Prius and PriusPrime w/7in. Display
Disassembly Overview
4
6
5
TVIP V5
RS3200 PLUS
1
Glove Box Under Cover
2
Glove Box
3
PS Dash Cover
4
Center Cluster Panel
5
Center Sub Cluster Panel
6
Audio Unit
2
3
Disconnect all Corresponding
Connectors.
1
PriusPrime w/11in. Display
Disassembly Overview
4
5
1
Glove Box Under Cover
2
Glove Box
3
PS Dash Cover
4
Top Center Cluster Cover
5
Center Cluster Panel
2
3
Disconnect all Corresponding
Connectors.
1
Issue H : 11/22/16
Page 6 of 36
TOYOTA
PREPARATION
PriusPrime
Prius
2017–
2016–
10mm Socket
Fig. 1-1
TVIP V5
RS3200 PLUS
1. Preparation.
a. Place the Vehicle in Park
with the Parking Brake set.
(Fig. 1-1)
b. Disconnect the Negative
Battery Terminal. (Fig. 1-1)
• Note the Battery Cable Position as
it will be re-inslalled in the same
position.
CAUTION: Do not touch the
Positive Terminal. (Fig. 1-1)
NOTE: Ensure all disassembled
Vehicle Parts are thoroughly
inspected. (Fig. 1-1)
Nylon Panel Removal Tool
Fig. 2-1
2. Vehicle Disassembly.
a. Dislodge the Glove Box
Under Cover. (Fig. 2-1)
• Disconnect all connectors.
Fig. 2-2
b. Disconnect the Damper from
the Glove Box. (Fig. 2-2)
c.
Issue H : 11/22/16
Page 7 of 36
Remove the Glove Box.
(Fig. 2-2)
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
TVIP V5
RS3200 PLUS
Nylon Panel Removal Tool
Fig. 2-3
d. Remove the Passenger’s
Side Dash Cover. (Fig. 2-3)
Nylon Panel Removal Tool
Fig. 2-4
e. Confirm if the vehicle includes
a clip inside the Passenger’s
Side Dash as shown. (Fig. 2-4)
If the vehicle does not have
the clip, proceed to the
following step.
Fig. 2-5
Issue H : 11/22/16
Page 8 of 36
f. Tilt and extend the Vehicle’s
Steering Wheel to the upward
position before moving forward
with the Vehicle’s Disassembly.
(Fig. 2-5)
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Nylon Panel Removal Tool
Fig. 2-6
TVIP V5
RS3200 PLUS
PriusPrime w/ 11in Display
ONLY
NOTE: Skip to step v for Prius
and PriusPrime w/7in. display.
g. Apply protective tape to
the areas shown in the
illustration. (Fig. 2-6)
h. Using a Nylon Panel
Removal Tool, disengage
the 4 clips as shown in the
illustration. (Fig. 2-6)
Nylon Panel Removal Tool
Fig. 2-7
Nylon Panel Removal Tool
Fig. 2-8
Issue H : 11/22/16
Page 9 of 36
i.
Disengage the claw and
2 clips as shown in the
illustration. (Fig. 2-7)
j.
Disengage the claw, clip
and base of the front pillar
garnish clip as shown in the
illustration. (Fig. 2-8)
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Nylon Panel Removal Tool
Fig. 2-9
TVIP V5
RS3200 PLUS
k.
While pushing the tabs of the
front pillar garnish clip as shown
in the illustration, remove the
center instrument cluster finish
panel upper. (Fig. 2-9)
NOTE: The front pillar garnish clip
is reusable if it is not damaged.
NOTE: If the front pillar garnish clip
is damaged, replace it with a new
one.
l.
While pushing the tab of the front
pillar garnish clip shown in the
illustration with your finger, move
the front pillar garnish clip in the
direction shown in the illustration.
(Fig. 2-9)
m. While pulling the front pillar
garnish clip as shown in the
illustration, push the tab of the
front pillar garnish clip shown in
the illustration with a screwdriver
and disengage the front pillar
garnish clip. (Fig. 2-9)
n. Remove the Top Center Cluster
Cover. (Fig. 2-9)
Nylon Panel Removal Tool, 10mm Socket, Extension
Fig. 2-10
o. Remove the 2 Bolts from inside
of the Center Cluster Panel as
shown. (Fig. 2-10)
• Remove 2 Bolts.
Issue H : 11/22/16
Page 10 of 36
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Protective Tape, Nylon Panel Removal Tool
Fig. 2-11
TVIP V5
RS3200 PLUS
p. Wrap the Center Cluster Panel in
a Protective Blanket. (Fig. 2-11)
• Apply Protection tape to the
corner of the Center Cluster
Panel and don’t remove until it is
re-installed.
Rear Side Connectors
q.
Slowly Dislodge and place the
Center Cluster Panel on the
Vehicle Bracket as shown.
(Fig. 2-11)
• Avoid excessive force to
avoid damage to the rear side
connectors.
r.
Vehicle Bracket
Remove the Center Cluster
Panel. (Fig. 2-11)
NOTE: Use caution when
removing the Center Cluster Panel
due to its weight. (Fig. 2-11)
Flat blade Jeweler’s Screwdriver, Nylon Panel Removal Tool, Pliers Fig. 2-12
s.
Remove Clip by reaching inside
the Center Cluster Panel as
shown. (Fig. 2-12)
• Remove 1 Clip.
NOTE: Disconnect all connectors,
except the connectors shown.
(Fig. 2-12)
t.
Remove the Center Cluster
Panel. (Fig. 2-12)
Continue to Section 3
Protective Tape, Nylon Panel Removal Tool
Prius and PriusPrime
w/7in. Display ONLY
Fig. 2-13
u.
Remove Clip by reaching inside
the Passenger’s Side Dash as
shown. (Fig. 2-13)
• Remove 1 Clip.
v.
Remove the Center Cluster
Panel. (Fig. 2-13)
NOTE: Use caution when
removing the Center Cluster
Panel due to it’s weight.
(Fig. 2-13)
Issue H : 11/22/16
Page 11 of 36
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Phillips Screwdriver
Fig. 2-14
TVIP V5
RS3200 PLUS
w. Remove the Center Sub
Cluster Panel. (Fig. 2-14)
• Remove 2 Screws.
x.
Carefully remove the Vehicle
Harness Clip as shown.
(Fig. 2-14)
NOTE: Ensure all disassembled
Panel connectors are carefully
disconnected. (Fig. 2-14)
10mm Socket, Extension
Fig. 2-15
y.
Remove the Audio Unit.
(Fig. 2-15)
• Remove 4 Bolts.
NOTE: Disconnect all connectors,
except the connectors shown.
(Fig. 2-15)
Fig. 3-1
3. GBS ECU & V5 Harness
Preparation and Installation.
CAUTION: Use gloves during
wire tie and ECU installation.
(Fig. 3-1)
NOTE: Ensure all Kit Parts are
thoroughly inspected before
installation. (Fig. 3-1)
a. Attach GBS ECU Bracket
to the GBS ECU as shown.
(Fig. 3-1)
Issue H : 11/22/16
Page 12 of 36
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Flat blade Jeweler’s Screwdriver
Fig. 3-2
TVIP V5
RS3200 PLUS
Vehicles with UV windows
ONLY
b. Set the GBS Sensitivity Value
to 7. (Fig. 3-2)
Flat blade Jeweler’s Screwdriver
Fig. 3-3
Vehicles with Acoustic
windows ONLY
c. Set the GBS Sensitivity Value
to “9”. (Fig. 3-3)
Utility Knife
Fig. 3-4
d. Cut one Quarter piece from
the Vinyl Sheet and save for
later use. (Fig. 3-4)
e. Cut one long Quarter piece
from the remaining Vinyl
Sheet as shown and save for
later use. (Fig. 3-4)
f. Cut the long quarter piece in
half. (Fig. 3-4)
1 x Long Quarter Piece
2 x Short Quarter Pieces
Issue H : 11/22/16
Page 13 of 36
TOYOTA
PriusPrime
Prius PROCEDURE
2017–
2016–
Electrical Tape
Fig. 3-5
1
2
TVIP V5
RS3200 PLUS
g. Plug the V5 8P White
Connector to the GBS ECU.
(Fig. 3-5)
h. Use the one Short Quarter
Piece of Vinyl Sheet and
wrap around bare harness,
then apply Electrical Tape
over the Vinyl Sheet.
(Fig. 3-5)
3
NOTE: When applying Electrical
Tape; avoid putting too much
strain on the bare 8P White
Connector wires. (Fig. 3-5)
10mm Socket, Torque Wrench
Fig. 3-6
i.
Place the GBS ECU on the
Vehicle Brace in the Glove
Box Area. (Fig. 3-6)
j.
Install the GBS ECU using
the supplied Bolt. (Fig. 3-6)
Torque: 8 N•m (71 in•lbf)
NOTE: Ensure all Kit Parts are
thoroughly inspected before
installation. (Fig. 3-6)
Side Cutters
Fig. 3-7
k. Secure both the V5 Harness
branches to the Vehicle
Reinforcement using 1 Wire
Tie (#1). (Fig. 3-7)
l.
1
Secure the V5 Harness to the
Vehicle Brace using 1 Wire
Tie (#2). (Fig. 3-7)
m. Secure the V5 Harness to the
HVAC Bracket using 1 Wire
Tie (#3). (Fig. 3-7)
n. Route the V5 Harness
upward and toward the Audio
Unit area. (Fig. 3-7)
2
3
Issue H : 11/22/16
Page 14 of 36
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Fig. 3-8
TVIP V5
RS3200 PLUS
PriusPrime w/ 11in Display
ONLY
NOTE: Skip to step q for Prius
and PriusPrime w/7in. display.
o. Continue to route the V5
Harness upward and toward
the Audio Unit area and behind
the Vehicle Harness. (Fig. 3-8)
Fig. 3-9
p. Plug in the V5 2P Connector
to the Vehicle’s 2P Connector.
(Fig. 3-9)
Continue to Section 3, step s
Fig. 3-10
Prius and PriusPrime
w/7in. Display ONLY
q. Continue to route the V5
Harness upward and toward the
Audio Unit area and behind the
Vehicle Harness. (Fig. 3-10)
Issue H : 11/22/16
Page 15 of 36
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
TVIP V5
RS3200 PLUS
Fig. 3-11
r. Plug in the V5 2P Connector
to the Vehicle’s 2P Connector.
(Fig. 3-11)
Fig. 3-12
s. Disconnect the Vehicle’s Glove
Box Lamp 2P Connector.
(Fig. 3-12)
CAUTION: Do not pull the 2P
Connector’s Harness. (Fig. 3-12)
Fig. 3-13
Issue H : 11/22/16
Page 16 of 36
t. Plug in the V5 2P Connector to
the Vehicle’s Glove Box Lamp
2P Connector. (Fig. 3-13)
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Fig. 3-14
Side Cutters
Fig. 3-15
TVIP V5
RS3200 PLUS
u. Plug in the V5 2P Connector to
the Vehicle’s Glove Box Lamp
2P Connector. (Fig. 3-14)
v. Wrap the V5 Harness using
the Short Quarter Piece
of Vinyl Sheet as shown.
(Fig. 3-15)
w.Secure the V5 Harness to the
Vehicle Reinforcement using
1 Wire Tie (#4). (Fig. 3-15)
x. Secure the V5 2P Connector
to the Vehicle’s Reinforcement
using 1 Wire Tie (#5).
(Fig. 3-15)
CAUTION: Avoid strain on the 2P
Connector’s Harness. (Fig. 3-15)
4
1
5
CAUTION: Ensure all bare wire
and Connectors are secured
within the Vinyl Sheet and
Electrical Tape. (Fig. 3-15)
Side Cutters
Fig. 3-16
NOTE: Skip to step ab for Prius
and PriusPrime w/7in. display.
y. Secure the V5 Harness in the
Audio Unit area to the Vehicle
Harness using 2 Wire Ties
(#6 & #7) as shown. (Fig. 3-16)
6
7
Issue H : 11/22/16
PriusPrime w/ 11in Display
ONLY
Page 17 of 36
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Side Cutters
Fig. 3-17
9
TVIP V5
RS3200 PLUS
z. Secure the V5 Harness to the
air conditioner unit using 2
Wire Ties (#8 & #9) as shown.
(Fig. 3-17)
CAUTION: Avoid contact between the V5 Harness and all
surrounding Sharp Clip edges.
(Fig. 3-17)
8
NOTE: Do not secure the surrounding 2P Connector wires.
(Fig. 3-17)
aa. Secure the V5 Harness to
the Vehicle Harness using
1 Wire Tie (#10). (Fig. 3-17)
10
Continue to Step ag
Side Cutters
Fig. 3-18
Prius and PriusPrime
w/7in. Display ONLY
ab. Secure the V5 Harness to
the Vehicle Harness using
1 Wire Tie (#6). (Fig. 3-18)
6
Side Cutters
Fig. 3-19
ac. Secure the V5 Harness to the
Vehicle Harness towards the
Driver’s Side Using 1 Wire
Tie (#7). (Fig. 3-19)
CAUTION: Avoid contact between the V5 Harness and all
surrounding Sharp Clip edges.
(Fig. 3-19)
7
NOTE: Do not secure the
surrounding 2P Connector wires.
(Fig. 3-19)
8
ad. Secure the V5 Harness to
the air conditioner unit using
1 Wire Tie (#8). (Fig. 3-19)
Issue H : 11/22/16
Page 18 of 36
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Side Cutters
Fig. 3-20
TVIP V5
RS3200 PLUS
ae. Secure the V5 Harness to the
air conditioner unit using
1 Wire Tie (#9). (Fig. 3-20)
af. Secure the V5 Harness to the
Vehicle Harness using
1 Wire Tie (#10). (Fig. 3-20)
10
9
Flat blade Jeweler’s Screwdriver, Pick Tool, Wiring Terminal Tool
Fig. 3-21
SKY BLUE
WIRE SIDE
ag. Pull out the Vehicle’s Sky
Blue Wire Terminal from the
indicated location on the
10P Vehicle Connector.
(Fig. 3-21)
NOTE: Do not pull out the White
and Blue Wire Terminal on the
opposite side of the connector.
(Fig. 3-21)
CAUTION: Using a pick tool or
wiring terminal tool, release and
pull out the terminal. (Fig. 3-21)
Fig. 3-22
Issue H : 11/22/16
Page 19 of 36
ah. Disconnect the V5 White 1P
Connector from the V5 White
1P Connector. (Fig. 3-22)
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Flat blade Jeweler’s Screwdriver, Pick Tool
Fig. 3-23
TVIP V5
RS3200 PLUS
ai. Lift the Terminal Retainer
Clip. (Fig. 3-23)
CAUTION: Do not pull out the
Retainer Clip. (Fig. 3-23)
aj. Insert the Vehicle’s Sky Blue
Wire Terminal into the V5 1P
Connector. (Fig. 3-23)
VERIFY: Terminal Pins are
properly inserted and do not
come out. (Fig. 3-23)
ak. Close the Terminal Retainer
Clip. (Fig. 3-23)
Fig. 3-24
al. Insert the V5 Sky Blue Wire
Terminal into the indicated
location on the 10P Vehicle
Connector. (Fig. 3-24)
CAUTION: Do not insert the V5
Sky Blue Terminal into the White
and Blue Wire Terminal on the
opposite side of the connector.
(Fig. 3-24)
VERIFY: Terminal Pins are
properly inserted and do not
come out. (Fig. 3-24)
Fig. 3-25
SKY BLUE
WIRE SIDE
Issue H : 11/22/16
Page 20 of 36
am.Connect the V5 White 1P
Connector to the V5 White
1P Connector. (Fig. 3-25)
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Fig. 3-26
Side Cutters, Electrical Tape
Fig. 3-27
11
TVIP V5
RS3200 PLUS
an. Connect the V5 White 1P
Connector to the V5 White 1P
Connector. (Fig. 3-26)
ao. Wrap the V5 Harness and
V5 1P Connectors using
the Long Quarter piece of
Vinyl Sheet and secure with
Electrical Tape as shown.
(Fig. 3-27)
CAUTION: Ensure all bare
wire and V5 1P Connectors are
secured within the Vinyl Sheet
and Electrical Tape. (Fig. 3-27)
ap. Secure the V5 Harness and
the Vinyl Sheet wrapped V5
Connectors to the Vehicle
Harness using 2 Wire Ties
(#11 & #12). (Fig. 3-27)
12
Fig. 3-28
3
Issue H : 11/22/16
Page 21 of 36
aq. Route the V5 Harness behind
then over the Vehicle’s
Dashboard. (Fig. 3-28)
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Side Cutters
Fig. 3-29
TVIP V5
RS3200 PLUS
ar. Secure the V5 Harness to
the air conditioner unit using
2 Wire Ties (#13 & #14) as
shown. (Fig. 3-29)
as. Secure the V5 Harness to the
Vehicle Harness using
1 Wire Tie (#15). (Fig. 3-29)
13
15
14
Side Cutters
Fig. 3-30
at. Secure the V5 Harness to
the Vehicle Harness using
1 Wire Tie (#16). (Fig. 3-30)
NOTE: Ensure the 2P White
Connector points downward.
(Fig. 3-30)
16
10mm Socket
1
Fig. 3-31
1
au. Partially reassemble the
vehicle as shown. (Fig. 3-31)
PriusPrime w/11in Display
1
Center Sub Cluster Panel
2
Top Center Cluster Cover
Prius / PriusPrime w/7in Display
1
2
3
y
pla
lay
is
sp in D
i
D
7
/
in e w
11
1
w/ Prim
e
s
u
im
i
r
P
Pr
ius and
Pr
ius
Pr
Issue H : 11/22/16
3
Audio Unit
Center Sub Cluster Panel
(Reassemble Center Sub Cluster Panel to
Center Cluster Panel on a work bench.)
Center Cluster Panel
NOTE: Reconnect all
corresponding Connectors.
(Fig. 3-31)
NOTE: Verify that panels fit
together properly, with no uneven
gaps. (Fig. 3-31)
2
Page 22 of 36
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
10mm Socket
Fig. 3-32
TVIP V5
RS3200 PLUS
av. Temporarily reconnect the
Negative Battery Cable.
(Fig. 3-32)
CAUTION: Do not touch the
positive Terminal. (Fig. 3-32)
Fig. 3-33
aw. Test the Air Conditioning and
Heating, then visually confirm
Wire Harness does not
interfere with HVAC or any
moving parts before glove
box is reinstalled. (Fig. 3-33)
ax. Disconnect the Negative
Battery Cable. (Fig. Fig. 3-33)
CAUTION: Do not touch the
positive Terminal. (Fig. 3-33)
Issue H : 11/22/16
Page 23 of 36
TOYOTA
PriusPrime
Prius PROCEDURE
2017–
2016–
Fig. 4-1
Prius and PriusPrime w/7in Display
Disassembly Overview
TVIP V5
RS3200 PLUS
4. Microphone Installation.
1
Audio Unit
Center Sub Cluster Panel
Already Installed
5
4
2
(Reassemble Center Sub
Cluster Panel to Center Cluster
Panel on a work bench.)
3
Center Cluster Panel
4
PS Dash Cover
5
Glove Box
Reconnect all Corresponding
Connectors.
Do not Install
PriusPrime w/11in Display
Disassembly Overview
1
Center Cluster Panel
2
Top Center Cluster Cover
3
PS Dash Cover
4
Glove Box
Already Installed
4
Reconnect all Corresponding
Connectors.
3
a. Reassemble the Vehicle
except for the Glove Box
Under Cover. (Fig. 4-1)
NOTE: Verify that panels fit
together properly, with no uneven
gaps. (Fig. 4-1)
Do not Install
Issue H : 11/22/16
Page 24 of 36
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Fig. 4-2
TVIP V5
RS3200 PLUS
Vehicles with UV windows
ONLY
b. Using the VDC approved
cleaner and Cleaning Method,
clean the area indicated on
the backside of the Glove Box
Under Cover. (Fig. 4-2)
0 mm
0 mm
c. Attach the GBS Microphone
to the backside of the Glove
Box Under Cover as shown.
(Fig. 4-2)
NOTE: Make sure to align GBS
Microphone to the Glove Box
Under Cover. (Fig. 4-2)
Utility Knife
Fig. 4-3
d. Cut Foam Tape in Half.
(Fig. 4-3)
1/2 Foam Tapes
Fig. 4-4
e. Apply both of the 1/2
Foam Tapes to the GBS
Microphone as shown.
(Fig. 4-4)
NOTE: Do not cover the
Microphone opening with the
Foam Tape. (Fig. 4-4)
NOTE: Do not cover the Clip with
the Foam Tape. (Fig. 4-4)
1/2 Piece
Foam Tapes
Issue H : 11/22/16
Page 25 of 36
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Fig. 4-5
TVIP V5
RS3200 PLUS
f. Connect the Microphone’s
2P Connector to the V5 2P
Connector. (Fig. 4-5)
g. Reinstall the Glove Box Under
Cover. (Fig. 4-5)
Fig. 4-6
Vehicles with Acoustic
windows ONLY
h. Using the VDC approved
cleaner and Cleaning Method,
clean the area indicated on
the backside of the Glove Box
Under Cover.(Fig. 4-6)
0 mm
0 mm
i.
NOTE: Make sure to align GBS
Microphone to the Glove Box
Under Cover. (Fig. 4-6)
Fig. 4-7
Issue H : 11/22/16
Attach the GBS Microphone
to the backside of the Glove
Box Under Cover as shown.
(Fig. 4-6)
Page 26 of 36
j.
Connect the Microphone’s
2P Connector to the V5 2P
Connector. (Fig. 4-7)
TOYOTA
PROCEDURE
PriusPrime
Prius 2017–
2016–
Fig. 4-8
TVIP V5
RS3200 PLUS
k. Apply 1 Foam Tape to the
GBS Microphone as shown.
(Fig. 4-8)
NOTE: Do not cover the
Microphone opening with the
Foam Tape. (Fig. 4-8)
NOTE: Do not cover the Clip with
the Foam Tape. (Fig. 4-8)
l.
Fig. 5-1
Reinstall the Glove Box
Under Cover. (Fig. 4-8)
5. Registration.
a. Verify that the D/C Cut Fuse
is Installed. (Fig. 5-1)
• If not Install now
10mm Socket
Fig. 5-2
b. Temporarily reconnect the
Negative Battery Cable.
(Fig. 5-2)
CAUTION: Do not touch the
positive Terminal. (Fig. 5-2)
Issue H : 11/22/16
Page 27 of 36
TOYOTA
PriusPrime
Prius PROCEDURE
2017–
2016–
Techstream
Fig. 5-3
TVIP V5
RS3200 PLUS
c. Connect the Techstream
Notebook to the Vehicle’s
Diagnostic Port. (Fig. 5-3)
d. With the Smart Key in your
possession, press the
Power Button twice to select
the Ignition “ON” position.
(Fig. 5-3)
Fig. 5-4
e. Start the TIS Techstream
Application by clicking on
the shortcut located on the
Desktop. (Fig. 5-4)
f. Click “Connect to Vehicle”.
(Fig. 5-4)
Fig. 5-5
TIS techstream
File Function
Setup
TIS
Connect to Vehicle
Open Scan Data File
Launch TIS
User
Help
Vehicle Connection Wizard(S301-04)
Select the Information and press Next
t e cRequired
h s Information:
tream
Division:
XXXXXX
Model:
XXXXXXXXX
Model Year:
20XX
Engine:
XXXXXXXX
Option:
XXXXXXXX
New Users Demo
Check for Scantool
Updates
Generic OBD II
Software
Registration
User/Language
Selection
h. Select any additional “Option”
items that are applicable to
the vehicle. (Fig. 5-5)
i.
Log Out
Optional Information:
VIN:
xxxxxxxxxxxxxxxxxxx
ABS
Memo:
Manual
Help
<Back
Next>
Cancel
Ver x.xx.xxx
Issue H : 11/22/16
g. Confirm that the information
displayed on the Vehicle
Connection Wizard is correct
for the vehicle. If not, verify
that the Techstream is
properly connected. (Fig. 5-5)
Page 28 of 36
Click “Next>”. (Fig. 5-5)
TOYOTA
PriusPrime
Prius PROCEDURE
2017–
2016–
Fig. 5-6
TVIP V5
RS3200 PLUS
j.
Click “Customize Setting”.
(Fig. 5-6)
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
System Selection Menu
Air Conditioner
Combination Meter
*Sliding Roof
Health Check
SRS Airbag
Main Body
Tilt&Telescopic
Main Body
Back Door
*Accessory Gateway *Driver Door
Combination Meter Mirror
D Door Motor
Sliding Roof
*Passenger Door
Driver Seat
Occupant Detection
Customize
Setting
ECU
Reprogramming
CAN
Bus. Check
Print
Close
S601-03
Generic English
DLC3
Fig. 5-7
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
k. Make sure that the
“Customize” tab is selected.
(Fig. 5-7)
l.
Custom ize
Select Customize Function
Wireless Door Lock
Security
Illuminated Entry
Light Control
Air Conditioner
Unit Conversion
Seat
Option Setup
Door Lock
Power Window
Warning
Side Roof
Display
Smart / Access
Others
Select “Option Setup”.
(Fig. 5-7)
m. Click
. (Fig. 5-7)
Print
Close
S601-03
Generic English
DLC3
Fig. 5-8
o. Click
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Customize
Select Customize Function
Wireless Door Lock
Security
Customize (S601-06 )
Wiper
Warning
Select Customize Paramete r
Tilt & Telesco
ITEM
Air Conditioner
Security System
Display
Retractable Hardtop
Compass Colibration
PSD & PBD operation
Seat
Door Lock
Power Window
Illuminated Entry
Light Control
Slide Roof
SETTING
Sensor
OFF Unit conversion
ON
Smart / Access
Others
TVSS
Option Setup
Item Description
Print
Close
S601-03
Issue H : 11/22/16
n. Select “ON”. (Fig. 5-8)
Generic English
DLC3
Page 29 of 36
. (Fig. 5-8)
TOYOTA
PriusPrime
Prius PROCEDURE
2017–
2016–
TVIP V5
RS3200 PLUS
Fig. 5-9
p. Click “Next” to accept the
changes to the Vehicle.
(Fig. 5-9)
Fig. 5-10
q. Click
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Customize
Utility Selection Menue
Select desired Utility and then press Next button.
Trouble Codes
Custimize
ECU Communication
ID (S601-06)
Registration
Customize
Smart Code Registration
Select Customize Parameter
Communication Check(Key Diag Mode)
Smart Code Erasure
Smart Code Reset
ITEM
Security System
Data List
OFF
ON
SETTING
Active Test
Monitor
Utility
Customize (S601-07)
Press Next to make the selected customize
changes
Next
Cancel
Item Description
Print
Close
S601-03
Generic English
DLC3
(Fig. 5-10).
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Customize
Select Customize Function
Wireless Door Lock
Security
Customize (S601-06)
Wiper
Warning
Select Customize Parameter
Tilt & Telesco
ITEM
Air Conditioner
Security System
Display
Retractable Hardtop
Compass Colibration
PSD & PBD operation
Seat
Door Lock
Power Window
Illuminated Entry
Light Control
Slide Roof
SETTING
Sensor
OFF Unit conversion
ON
Smart / Access
Others
TVSS
Option Setup
Item Description
Print
Close
S601-03
Generic English
DLC3
Fig. 5-11
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Customize
Select Customize Function
Wireless Door Lock
Security
Illuminated Entry
Light Control
Air Conditioner
Unit Conversion
Option Setup
Door Lock
Power Window
Warning
Slide Roof
Display
Smart / Access
Others
Print
Close
S601-03
Issue H : 11/22/16
Generic English
DLC3
Page 30 of 36
r. Click “Close”. (Fig. 5-11)
TOYOTA
PriusPrime
Prius PROCEDURE
2017–
2016–
Fig. 6-1
Clear Tape
10 mm
TVIP V5
RS3200 PLUS
6. Window Label Installation.
• For US Vehicles use the English Tags
and Labels, and discard the Spanish
Tags and Labels. (Fig. 6-1)
• For Mexico Vehicles use the Spanish
Tags and Labels, and discard the
English Tags and Labels. (Fig. 6-1)
a. Use VDC Approved Cleaner
to clean the inside of
the Front Door Window.
(Fig. 6-1)
MOLDING
HE
GN
C
ET
T
R
HE
TO
OT
O
NT
I
AL
TO ALIG
W
HO W TO
HO
NG
HI LS
BE
LA
1– 5 mm
b. Use a piece of Clear Tape to
lift the Label off its protective
backing. (Fig. 6-1)
CAUTION: Do not touch the
adhesive surface. (Fig. 6-1)
MOLDING
c. Attach the Label as shown.
NOTE: Make sure to Align the
Label according to Etching or
Other Label. (Fig. 6-1)
REPEAT: Steps a-c with the other
Window. (Fig. 6-1)
Torque Wrench
Fig. 7-1
7. Complete the Installation.
a. Position the Negative Battery
Cable at the original factory
position. (Fig. 7-1)
Torque: 5.4 N•m (48 in•lbf)
CAUTION: Do not touch the
Positive Terminal. (Fig. 7-1)
b. Clean up and remove trash.
c. Sealed in its protective bag,
place the Owner’s Guide in
the Glove Box.
Issue H : 11/22/16
Page 31 of 36
TOYOTA
CHECKLIST – these points MUST be checked to ensure a quality installation.
PriusPrime 2017–
Prius
2016–
TVIP V5
RS3200 PLUS
Accessory Function Checks
Roll up all windows, and exit the vehicle with the remote.
Perform
Look For
1
Press and release the remote control lock
button to start the system’s arming process.
The turn signal lights flash once.
All doors lock.
The security LED lights up.
2
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
3
Press and release the remote control’s
unlock button to disarm the system.
The turn signal lights flash twice.
The driver’s door unlocks.
The Security LED stops flashing.
Open the driver’s door, with the smart key in your possession, press the power button to “ON.” Roll down all
the windows, remove the key and exit the vehicle.
4
Arm and disarm the system with the remote
again, then wait 30 seconds.
The doors automatically relock.
The system automatically starts the arming process.
5
Press and release the remote control’s
unlock button again to stop the arming
process.
Refer to step 3
6
Press the lock button on the driver’s exterior
door handle to start the arming process.
All doors lock.
The Security LED lights up.
7
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
8
Reach inside and manually unlock the
driver’s door to trigger an alarm.
The driver’s door automatically relocks.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up.
9
Manually unlock the driver’s door again and
hold it unlocked, open the door, then sit in
the driver’s seat.
The driver’s door lock attempts to lock repeatedly.
The horn continues to sound repeatedly.
The headlights and turn signal lights continue flashing.
The Security LED remains on.
10
The smart key in your possession, press the
power button twice to “START” to stop the
alarm.
The horn stops sounding.
All the lights stop flashing and/or turn off.
The Security LED turns off.
The starter cranks and the engine starts.
Press the power button to turn the vehicle off, and then exit the vehicle.
11
With the door open, press the lock switch
on the door to lock the doors, then close the
door to start the system’s arming process.
All doors lock.
The Security LED lights up.
12
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
13
Reach inside and manually unlock the front
passenger’s door to trigger an alarm.
The front passenger’s door automatically relocks.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The SECURITY LED lights up.
Issue H : 11/22/16
Page 32 of 36
TOYOTA
CHECKLIST – these points MUST be checked to ensure a quality installation.
PriusPrime 2017–
Prius
2016–
14
Press and release the remote control’s
unlock button to stop the alarm.
The horn stops sounding.
All the lights stop flashing.
The Security LED stops flashing.
15
Press and release the remote control’s lock
button to start the system’s arming process,
then wait 30 seconds until the system is
armed.
Refer to steps 1 and 2.
16
Unlock and open one of the rear passenger
doors to trigger an alarm. (if available).
Refer to step 13.
17
Press and release the remote control’s
unlock button to stop the alarm.
Refer to Step 14
18
Repeat the above steps with the other rear
passenger door. (if available).
Refer to steps 1, 2, and 13.
TVIP V5
RS3200 PLUS
For Vehicles with UV Glass. (For Vehicles with Acoustic Glass, Skip to Steps 23 - 26)
Roll up all windows, remove the key and exit the vehicle.
Take the Smart Key from the Vehicle and place them 15 ft. (4.5 meters) or more away from the Vehicle.
19
Press and release the remote control’s lock
button to start the arming process.
Refer to step 1.
20
Wait 30 seconds.
After 30 seconds, the Security LED starts flashing; the
system is now armed.
Perform the following check in a temperature-controlled environment. (50°- 90° F)
21
With the tip of a key, or Striker Tool pulled
all the way out (PPO only), tap the center
of the driver’s door window to trigger the
alarm.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up.
22
Insert the key into the driver’s door key
cylinder and turn it toward the back of the
vehicle to stop the alarm.
Refer to Step 14
Skip to Vehicle Function Checks. (See Page 32)
For Vehicles with Acoustic Glass.
This procedure will require an assistant. With the installer inside the vehicle, roll up all windows.
Take out the Smart Key and the Smart Card Key from the Vehicle. Place them 15 feet (4.5 meters) or more away from
the Vehicle.
Perform
Look For
23
Have assistant lock the doors with installer
inside of the Vehicle, then start the system’s
arming process.
The turn signal lights flash once.
All doors lock.
The Security LED lights up.
24
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
Perform the following check in a temperature controlled environment (50°- 90° F)
Issue H : 11/22/16
Page 33 of 36
TOYOTA
CHECKLIST – these points MUST be checked to ensure a quality installation.
PriusPrime 2017–
Prius
2016–
25
With the tip of a key, or Striker Tool pulled
all the way out (PPO only), have installer
tap the center of the driver’s door window
from the inside to trigger the alarm.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up.
26
Assistant must insert the key into the
driver’s door key cylinder and turn it toward
the back of the vehicle to stop the alarm.
The horn stops sounding.
All the lights stop flashing and/ or turn off.
The Security LED lights up.
TVIP V5
RS3200 PLUS
NOTE: If the alarm does not trigger during functional verifications the Smart Key and Smart Card Key might be too
close. Move them farther from the vehicle and test the system again.
NOTE: If the alarm still does not trigger during the section test, increase the GBS sensitivity to the next setting and
test again.
NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration.
Vehicle Function Checks
Function
Function
Enter the Vehicle
□
□
Dome/Courtesy Lights
Start the Vehicle
□
□
Check Engine Light
If the warning light remains on, it may
indicate a system malfunction.
□
Lamp Failure Sensor
□
Seat Belt Warning Light
□
□
□
Panel/Switch Illumination
CHECK
If the warning light remains on, it may
indicate a system malfunction.
If the warning light remains on, it may
indicate a system malfunction.
Gauges
□
ABS Light (if equipped)
□
Track/Skid Control Light (if equipped)
□
Tire Pressure Monitoring System
(TPMS).
If the warning light remains on, it may
indicate a system malfunction.
If the warning light remains on, it may
indicate a system malfunction.
Air Bag Warning Light
Prior to TPMS activation and Pre-delivery
Service (PDS) of the Vehicle the TPMS light
will blink when IG is turned on.
Cruise Control Light (if equipped)
After TPMS activation and PDS of the Vehicle the TPMS light will illuminate for a few
seconds and go off when IG is turned on.
If the warning light remains on, it may
indicate a system malfunction.
Using a Mirror or Assistant check the following.
□
□
Illuminated Door Sills (If Equipped)
Trunk/Tailgate/Bed Lights (if equipped)
Brake Lights
Issue H : 11/22/16
□
□
Page 34 of 36
Tail Lights
Daytime Running Lights (if equipped)
TOYOTA
CHECKLIST – these points MUST be checked to ensure a quality installation.
□
□
□
Backup Lights
PriusPrime 2017–
Prius
2016–
TVIP V5
RS3200 PLUS
Marker Lights
Clearance Sonar (if equipped)
Stop the Engine, Place the Vehicle’s IG in the ON position.
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
Hazard Lights
Head Light
High Beams
Power Side Mirrors (if equipped)
Horn
Front Wiper/Washer
Power Sun/Moon Roof (if equipped)
Clock (if equipped)
Audio/Video (if equipped)
Steering Wheel Audio Control (if equipped)
Front Windshield Defogger (if equipped)
Side Mirror Defogger (if equipped)
Glove Box Light (if equipped)
Power Locks (if equipped)
Power Seats (if equipped)
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
Turn Signal Lights
Fog Lights (if equipped)
Accessory Controls/Illumination (if equipped)
Convenience Memory Settings (if equipped)
Rear Wiper/Washer (if equipped)
Rollover Side Curtain Air Bag Switch (RSCA)
(if equipped)
Navigation System (if equipped)
HVAC
Air Conditioning/Heating
Rear Window Defogger (if equipped)
Accessory Power Socket (if equipped)
Heated/Vented Seats (if equipped)
Glove Box Undercover Light
Power Windows (if equipped)
Key Sensor Buzzer
Vehicle Appearance Check
Perform
□
After accessory installation and removal
of protective cover(s), perform a visual
inspection of the vehicle.
Issue H : 11/22/16
Look For
Ensure no damage (including scuffs and scratches) was
caused during the installation process.
(For PPO installations, refer to TMS Accessory Quality
Shipping Standard.)
Page 35 of 36
TOYOTA
CHECKLIST – these points MUST be checked to ensure a quality installation.
Remove the D/C Cut Fuse after Function check.
Check with your Port/Dealer to see if this step is necessary.
Issue H : 11/22/16
Page 36 of 36
PriusPrime 2017–
Prius
2016–
TVIP V5
RS3200 PLUS
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement