AOC I2269 VWM, VW, I2369 V, VM, I2769 V, VM LCD Monitor User Manual
Below you will find brief information for I2269VWM, I2269VW, I2369V, I2369VM, I2769V, I2769VM. These AOC monitors offer various features including LED backlighting, adjustable viewing angles, multiple input connectors (VGA, DVI, HDMI, DP, MHL), and OSD settings for brightness, contrast, color, and image setup. They support various resolutions and offer hotkeys for quick access to common functions. The manual provides detailed setup, troubleshooting, and specification information.
advertisement
I2269V
WM
/I2269V
W
/I2369V
I2369V
M
/I2769V/I2769V
M
LED Backlight
Driver ...................................................................................................................................................................... 35
Monitor Driver .................................................................................................................................................. 35
Windows 7 ................................................................................................................................................ 35
Specification ............................................................................................................................................................49
General Specification .......................................................................................................................................49
Preset Display Modes ......................................................................................................................................50
FCC Notice ...........................
Safety
National Conventions
The following subsections describe notational conventions used in this document
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.
These blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your computer system.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.
Power
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
To ensure satisfactory operation, use the monitor only with certified computers which have appropriate configured receptacles marked between 100 - 240V ~, Min. 5A
The wall socket shall be installed near the equipment and shall be easily accessible.
Installation
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
Do not place the front of the product on the floor.
If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence overheating may cause a fire or damage to the monitor.
See below the recommended ventilation areas around the monitor when the monitor is installed on the stand:
Cleaning
Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
Please disconnect the power cord before cleaning the product.
Other
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.
Setup
Contents in Box
Monitor
*
CD Manual
* *
Base
* *
MHL Cable
*
Power Cable Analog Cable DVI Cable DP Cable Audio Cable HDMI Cable
Not all signal cables (VGA, DVI,MHL and HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.
Setup Stand & Base
Please setup or remove the base following the steps as below.
Setup:
Remove:
Adjusting Viewing Angle
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference.
Hold the stand so you will not topple the monitor when you change the monitor's angle.
You are able to adjust the monitor's angle from - 5° to 23°.
-5°
23°
NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
Connecting the Monitor
Cable Connections In Back of Monitor and Computer:
I2269V
WM
/I2369V
M
/I2769V
M
1
1. Power
2. Earphone
3. Audio port
4. D-Sub port
5 . HDMI1/MHL port
6 . HDMI2 port
7. DP port
7 5 6 4 3 2
To protect equipment, always turn off the PC and LCD monitor before connecting.
1 Connect the power cable to the AC port on the back of the monitor.
2 Connect one end of the 15-pin D-Sub/HDMI
/MHL/DP
port to the back of the monitor and connect the other end
to the computer's D-Sub/HDMI / mobile MHL/DP port.
3 Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image, please refer
Troubleshooting.
Connecting the Monitor
Cable Connections In Back of Monitor and Computer:
I2269V
W
/I2369V /I2769V
DVI
1. Power
2. D-Sub port
3. DVI port
1 33 2
To protect equipment, always turn off the PC and LCD monitor before connecting.
1 Connect the power cable to the AC port on the back of the monitor.
2 Connect one end of the 15-pin D-Sub/ DVI port to the back of the monitor and connect the other end to the computer's D-Sub/ DVI .
3 Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image, please refer
Troubleshooting.
Adjusting
Setting Optimal Resolution
Windows 8
For Windows 8:
1. Right click and click All apps at the bottom-right of the screen.
2. Set the “ view by” to “Category”.
5. Set the resolution
SLIDE-BAR to 1920x1080 or 2560x1080.
Windows Vista
For Windows Vista:
1 Click START.
2 Click CONTROL PANEL.
3 Click Appearance and Personalization.
4 Click Personalization
5 Click Display Settings.
6 Set the resolution SLIDE-BAR to Optimal preset resolution .
Windows XP
For Windows XP:
1 Click START.
2 Click SETTINGS.
3 Click CONTROL PANEL.
4 Click Appearance and Themes.
5 Double click DISPLAY.
6 Click SETTINGS.
7 Set the resolution SLIDE-BAR to Optimal preset resolution
Windows ME/2000
For Windows ME/2000:
1 Click START.
2 Click SETTINGS.
3 Click CONTROL PANEL.
4 Double click DISPLAY.
5 Click SETTINGS.
6 Set the resolution SLIDE-BAR to Optimal preset resolution
Hotkeys
1 2 3 4 5
I2269V
WM
/I2369V
M
/I2769V
M
4
5
1 Source/Auto/Exit
2 Clear Vision/ >
3 Volume/ >
Menu/Enter
Power
Power
Press the Power button to turn on/off the monitor.
I2269V
W
/I2369V/I2769V
4
5
1 Source/Auto/Exit
2
3
Clear Vision/ >
4:3 or wide / >
Menu/Enter
Power
Menu/Enter
Press to display the OSD or confirm the selection.
Volume/ >
When there is no OSD, press Volume adjust volume.
4:3 or wide image ratio / > is 4:3 or input signal resolution is wide format, the hot key is disable to adjust. )
Auto / Exit / Source hot key
When there is no OSD, press Auto/Source button continuously about 2 second to do auto configure.
When the OSD is closed, press Source button will be Source hot key function. Press Source button continuously to select the input source showed in the message bar, press Menu/Enter button to change to the source selected.
Clear Vision/
>
>
Clear Vision medium, strong, or off settings. Default setting is
always “off”
3.
Press and hold “ < ” button for 5 seconds ,the vertical line
“ < ” button for 5 seconds ,the vertical line will the display vertical monitor line is moving in screen; Press the “<” Button to turn the of will vertical be clear clear line vision vision will be off ; the
Off / Strong / Medium / Weak, the left effect
When demo display and picture right in of vertical screen will line be more obviously.
Clear Vision function will provides the best image viewing experience by converting low resolution and blurry images into clear and vivid images.
Using "MHL(Mobile High-Definition Link)"
1. "MHL" (Mobile High-Definition Link)
This feature allows you to enjoy videos and photos (imported from a connected mobile device that supports MHL) on the screen of the product. z To use the MHL function, you need an MHL-certified mobile device. You can check if your mobile device is MHL certified on the device manufacturer's website. To find a list of MHL-certified devices, visit the official MHL website
(http://www.mhlconsortium.org). z To use the MHL function, the latest version of software must be installed on the mobile device. z On some mobile devices, the MHL function may not be available depending on the device's performance or functionality. z Since the display size of the product is larger than those of mobile devices, the picture quality may degrade. z This product is officially MHL-certified. If you encounter any problem when using the MHL function, please contact the manufacturer of the mobile device. z The picture quality may degrade when content (imported from the mobile device) with a low
Resolution is played on the product.
Using "MHL"
1. Connect the micro USB port on the mobile device to the [HDMI 1 / MHL] port on the product using the MHL cable. z When the MHL cable is used, [HDMI 1/ MHL] is the only port on this monitor that supports the MHL function. z Mobile device must be purchased separately.
2. Press the source button and switch to HDMI 1/MHL to activate MHL mode.
3. After about 3 seconds, the MHL screen will be displayed if MHL mode is active.
Remark: The indicated time "3 sec later" may vary depending on the mobile device.
When the mobile device is not connected or does not support MHL z If MHL mode is not activated, check the connection of the mobile device.
z If MHL mode is not activated, check if the mobile device supports MHL. z If MHL mode is not activated even though the mobile device supports MHL, update the firmware of the mobile device to the latest version.
OSD Setting
Basic and simple instruction on the control keys.
1) Press the MENU-button to activate the OSD window.
2) Press <
or to navigate through the functions. Once the desired function is highlighted, press the function is highlighted, press MENU-button to activate it.
3) Press < or to change the settings of the selected function. Press AUTO to exit. If you want to adjust any other function, repeat steps 2-3.
4) OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press
power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn the monitor on.
Notes:
1) If the product has only one signal input, the item of "Input Select" is disable to adjust.
2) If the product screen size is 4:3 or input signal resolution is wide format, the item of "Image Ratio" is disable to
3) adjust.
One of non-standard ECO, DCR , DCB, Picture Boost is activated the other three of functions are turned off accordingly.
Luminance
1. Press MENU (Menu) to display menu.
2. Press < or to select (Luminance), and press MENU to enter.
3. Press < or to select submenu, and press MENU to enter.
4. Press or > to adjust.
5. Press AUTO to exit
.
I2269 V
WM
/I2369V
M
/ I2769V
M
Brightness
Contrast
0-100
0-100
Standard
Text
Eco mode
Gamma
DCR
Overdrive
DPS
Internet
Game
Movie
Sports
Gamma1
Gamma2
Gamma3
Off
On
Weak
Med i um
Strong
O ff
Off
On
Backlight Adjustment
Contrast from Digital-register.
Standard Mode
Text Mode
Internet Mode
Game Mode
Movie Mode
Sports Mode
Adjust to Gamma1
Adjust to Gamma 2
Adjust to Gamma 3
Disable dynamic contrast ratio
Enable dynamic contrast ratio
A djust the response time
Dynamic Power saving
I2269V
W
/I2369V /I2769V
Brightness
Contrast
Eco mode
Gamma
DCR
0-100
0-100
Standard
Text
Internet
Game
Movie
Sports
Gamma1
Gamma2
Gamma3
Off
On
Backlight Adjustment
Contrast from Digital-register.
Standard Mode
Text Mode
Internet Mode
Game Mode
Movie Mode
Sports Mode
Adjust to Gamma1
Adjust to Gamma 2
Adjust to Gamma 3
Disable dynamic contrast ratio
Enable dynamic contrast ratio
Image Setup
1. Press MENU (Menu) to display menu.
2. Press or > to select (Image Setup), and press MENU to enter.
3. Press or > to select submenu, and press MENU to enter.
4. Press or > to adjust.
5. Press AUTO to exit
.
Clock
Phase
Sharpness
H.Position
V.Position
0-100
0-100
0-100
0-100
0-100
Adjust picture Clock to reduce Vertical-Line noise.
Adjust Picture Phase to reduce Horizontal-Line noise
Adjust picture sharpness
Adjust the horizontal position of the picture.
Adjust the vertical position of the picture.
Color Setup
1. Press MENU (Menu) to display menu.
2. Press or > to select (Color Setup), and press MENU to enter.
3. Press or > to select submenu, and press MENU to enter.
4. Press or > to adjust.
5. Press AUTO to exit
.
Color setup.
DCB Mode
DCB Demo
Warm
Normal
Cool sRGB
Recall Warm Color Temperature from EEPROM.
Recall Normal Color Temperature from EEPROM.
Recall Cool Color Temperature from EEPROM.
Recall SRGB Color Temperature from EEPROM.
User
Red
Green
Blue
Red Gain from Digital-register
Green Gain Digital-register.
Blue Gain from Digital-register
Full Enhance on or off Disable or Enable Full Enhance Mode
Nature Skin on or off Disable or Enable Nature Skin Mode
Green Field on or off Disable or Enable Green Field Mode
Sky-blue
AutoDetect on or off Disable or Enable Sky-blue Mode on or off Disable or Enable AutoDetect Mode
On or off Disable or Enable Demo
Picture Boost
1. Press MENU (Menu) to display menu.
2. Press or
> to select (Picture Boost), and press MENU to enter.
3. Press or > to select submenu, and press MENU to enter.
4. Press or > to adjust.
5. Press AUTO to exit
.
Frame Size
Brightness
Contrast
H. position
V.position
Bright Frame
14-100
0-100
0-100
0-100
0-100 on or off
Adjust Frame Size
Adjust Frame Brightness
Adjust Frame Contrast
Adjust Frame horizontal Position
Adjust Frame vertical Position
Disable or Enable Bright Frame
OSD Setup
1. Press MENU (Menu) to display menu.
2. Press or > to select (OSD Setup), and press MENU to enter.
3. Press or > to select submenu, and press MENU to enter.
4. Press or > to adjust.
5. Press AUTO to exit
.
H.Position
V.Position
Timeout
Transparence
Language
Break Reminder
0-100
0-100
5-120
0-100
Off
On
Adjust the horizontal position of OSD
Adjust the vertical position of OSD
Adjust the OSD Timeout
Adjust the transparence of OSD
Select the OSD language
Break reminder if the user continuously work for more than1hrs
Extra
1. Press MENU (Menu) to display menu.
2. Press or > to select (Extra), and press MENU to enter.
3. Press or
> to select submenu, and press MENU to enter.
4. Press or > to adjust.
5. Press AUTO to exit
.
I2269V
WM
/I2369V
M
/I2769V
M
Auto
Input Select D-SUB
HDMI1/ MHL
HDMI2
Auto Config yes or no
Image Ratio wide or 4:3
DDC-CI yes or no
Reset
Off Timer
Information yes or no
0~24hours
I2269V
W
/I2369V /I2769V
Auto
Input Select
D-SUB
DVI
Auto Config yes or no
Image Ratio wide or 4:3
DDC-CI
Reset yes or no yes or no
Off Timer
Information
0~24hours
Select to Auto Detect input signal
Select D-SUB Signal Source as Input
Select
Select HDMI2
Auto adjust the picture to default
Select wide or 4:3 format for display
Turn ON/OFF DDC-CI Support
Reset the menu to default
Select timing to turn off the monitor.
Show the information of the main image and sub-image source
Select to Auto Detect input signal
Select D-SUB Signal Source as Input
Select DVI Source as Input
Auto adjust the picture to default
Select wide or 4:3 format for display
Turn ON/OFF DDC-CI Support
Reset the menu to default
Select timing to turn off the monitor.
Show the information sub-image source of the main image and
Exit
1. Press MENU (Menu) to display menu.
2. Press or
> to select (Exit), and press MENU or AUTO to exit
.
Exit Exit the main OSD
LED Indicator
Status
Full Power Mode
Active-off Mode
LED Color
Green
orange
Driver
Monitor Driver
Windows 8
1. Start Windows® 8
2. Right click and click All apps at the bottom-right of the screen.
3. Set the “View by” to “Large icons” or “Small icons”.
4. Click on the “Display” icon.
5. Click on the “Change display settings” button.
6. Click the
“
Advanced Settings” button.
7. Click the “Monitor” tab and then click the “Properties”
button
.
8. Click the “Driver” tab.
9. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver... “ and then click the "Browse my computer for driver software" button.
10. Select "Let me pick from a list of device drivers on my computer".
11. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory:
X:\Driver\module name (where X is the drive letter designator for the CD-ROM drive).
12. Select the "xxx.inf" file and click the “Open” button. Click the “OK” button.
13. Select your monitor model and click the “Next” button. The files will be copied from the CD to your hard disk drive.
14. Close all open windows and remove the CD.
15. Restart the system. The system will automatically select the maximum refresh rate and corresponding Color
Matching Profiles.
Windows 7
1. Start Windows® 7
2. Click on the 'Start' button and then click on 'Control Panel'.
3. Click on the “Display” icon.
4. Click on the “Change display settings” button.
5. Click the
“
Advanced Settings” button.
6. Click the “Monitor” tab and then click the “Properties”
button.
7. Click the “Driver” tab.
8. Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Driver... “ and then click the "Browse my computer for driver software" button.
9. Select "Let me pick from a list of device drivers on my computer".
10. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory:
X:\Driver\module name (where X is the drive letter designator for the CD-ROM drive).
11. Select the "xxx.inf" file and click the “Open” button. Click the “OK” button.
12. Select your monitor model and click the “Next” button. The files will be copied from the CD to your hard disk drive.
13. Close all open windows and remove the CD.
14. Restart the system. The system will automatically select the maximum refresh rate and corresponding Color
Matching Profiles.
Windows Vista
1. Click "Start " and "Control Panel". Then, double-click on "Appearance and Personalization".
2. Click "Personalization" and then "Display Settings".
3. Click "Advanced Settings...".
4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is.
If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue".
5. Click "Update Driver..." in the "Driver" tab.
6. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
7. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive
F:\Driver (CD-ROM Drive).
8. Select your monitor model and click on the 'Next' button.
9. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Windows XP
1. Start Windows® XP
2. Click on the 'Start' button and then click on 'Control Panel'.
3. Select and click on the category ‘Appearance and Themes’
4. Click on the 'Display' Item.
5. Select the 'Settings' tab then click on the 'Advanced' button.
6. Select 'Monitor' tab
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.
- If the 'Properties' button is active, click on 'Properties' button.
Please follow the steps below.
7. Click on the 'Driver' tab and then click on 'Update Driver...' button.
8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button.
9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive F:
(CD-ROM Drive).
11. Click on the 'Open' button, then click the 'OK' button.
12. Select your monitor model and click on the 'Next' button.
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with Windows® XP' message, please click on the 'Continue Anyway' button.
13. Click on the 'Finish' button then the 'Close' button.
14. Click on the 'OK' button and then the 'OK' button again to close the Display Properties dialog box.
Windows 2000
1. Start Windows® 2000
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select 'Monitor'
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below.
6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.
7. Select 'Display a list of the known drivers for this device so that I can choose a specific driver', then click on
'Next' and then click on 'Have disk...'.
8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).
9. Click on the 'Open' button, then click on the 'OK' button.
10. Select your monitor model and click on the 'Next' button.
11. Click on the 'Finish' button then the 'Close' button.
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.
Windows ME
1. Start Windows® Me
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select the 'Monitor' button, then click on 'Change...' button.
6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.
7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want', then click on 'Next' and then click on 'Have Disk...'.
8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK' button.
9. Click on the 'OK' button, select your monitor model and click on the 'Next' button.
10. Click on 'Finish' button then the 'Close' button.
i-Menu
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation guide.
e-Saver
Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or
Screen Saver); the actual shutdown time depends on your preferences (see example below).
Please click on "driver/e-Saver/setup.exe" to start installing the e-Saver software, follow the install wizard to complete software installation.
Under each of the four PC status, you may choose from the pull-down menu the desired time (in minutes) for your monitor to automatically shutdown. The example above illustrated:
1) The monitor will never shutdown when the PC is powered on.
2) The monitor will automatically shutdown 5 minutes after the PC is powered off.
3) The monitor will automatically shutdown 10 minutes after the PC is in sleep/stand-by mode.
4) The monitor will automatically shutdown 20 minutes after the screen saver appears.
You can click “RESET” to set the e-Saver to its default settings like below.
Screen+
Welcome to "Screen+" software by AOC, Screen+ software is a desktop screen splitting tool, it splits the desktop into different panes, each pane displays a different window. You only need to drag the window to a corresponding pane, when you want to access it. It supports multiple monitor display to make your task easier. Please follow the installation software to install it.
Troubleshoot
Problem & Question Possible Solutions
Power LED Is Not ON
Horizontal or vertical disturbances on the screen
Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor.
No images on the screen
Picture Is Fuzzy & Has
Ghosting Shadowing Problem
Picture Bounces, Flickers Or
Wave Pattern Appears In The
Picture
Monitor Is Stuck In Active
Off-Mode"
Is the power cord connected properly?
Check the power cord connection and power supply.
Is the cable connected correctly?
(Connected using the D-sub cable)
Check the DB-15 cable connection.
(Connected using the DVI cable)
Check the DVI cable connection.
* DVI input is not available on every model.
If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card.
(Refer to the Setting the Optimal Resolution)
If the initial screen (the login screen) does not appear, contact the Service
Center or your dealer.
Can you see "Input Not Supported" on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly.
Adjust the maximum resolution and frequency that the monitor can handle properly.
Make sure the AOC Monitor Drivers are installed.
Adjust the Contrast and Brightness Controls.
Press to auto adjust.
Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back .
Move electrical devices that may cause electrical interference as far away from the monitor as possible.
Use the maximum refresh rate your monitor is capable of at the resolution your are using.
The Computer Power Switch should be in the ON position.
The Computer Video Card should be snugly fitted in its slot.
Make sure the monitor's video cable is properly connected to the computer.
Inspect the monitor's video cable and make sure no pin is bent.
Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.
Missing one of the primary colors (RED, GREEN, or
BLUE)
Screen image is not centered or sized properly
Picture has color defects
(white does not look white)
Inspect the monitor's video cable and make sure that no pin is damaged.
Make sure the monitor's video cable is properly connected to the computer.
Adjust H-Position and V-Position or press hot-key (AUTO).
Adjust RGB color or select desired color temperature.
Use Windows 95/98/2000/ME/XP shut-down mode Adjust CLOCK and
FOCUS.
Press to auto-adjust.
Specification
General Specification
I2269V
WM
Panel
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Display Color
Dot Clock
I2269V
WM
TFT Color LCD
546.20mm Diagonal
0.08265*RGB(H)mm x 0.24795 (V)mm
R, G, B Analog lnterface ,HDMI ,MHL,DP
H/V TTL
16.7M Colors
170MHz
Horizontal scan range 30kHz to 83kHz
Horizontal scan Size(Maximum) 476.06
mm
Vertical scan range 50Hz to 76Hz
Vertical scan Size(Maximum) 267.79mm
Optimal preset resolution
Resolution
Plug & Play
Input Connector
Input Video Signal
Power Source
1920×1080@60Hz
VESA DDC2B/C1
VGA,HDMI, DP
Analog: 0.7Vp-p(standard),75 OHM,Positive,HDMI,MHL,DP
Power Consumption
Off timer
Connector Type
Signal Cable Type
100-240V~, 50/60Hz
Active<30W(Typical)
Standby < 0.5 W
0-24 hrs
VGA, HDMI, DP
Detachable
Dimensions & Weight:
Physical Height (with base)
Characteristics Width
Depth
379.4mm
498.3mm
189.2mm
3.55kg
Weight (monitor only)
Environmental Temperature:
Operating
Non-Operating
Humidity:
Operating
Non-Operating
Altitude:
Operating
Non-Operating
0° to 40°
-25°to 55°
10% to 85% (non-condensing)
5% to 93% (non-condensing)
1 404 ft )
0~ 12192m (0~ 40000 ft )
I2269V
W
Panel
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Display Color
Dot Clock
Horizontal scan range
I2269V
W
TFT Color LCD
546.20mm Diagonal
0.08265*RGB(H)mm x 0.24795 (V)mm
R, G, B Analog lnterface ,DVI
H/V TTL
16.7M Colors
170MHz
30kHz to 83kHz
Horizontal scan Size(Maximum) 476.06
mm
Vertical scan range 50Hz to 76Hz
Vertical scan Size(Maximum) 267.79mm
Optimal preset resolution
Resolution
Plug & Play
Input Connector
Input Video Signal
Power Source
1920×1080@60Hz
VESA DDC2B/C1
VGA, DVI
Power Consumption
Analog: 0.7Vp-p(standard),75 OHM,Positive,DVI
100-240V~, 50/60Hz
Active<25W(Typical)
Standby < 0.5 W
0-24 hrs
VGA, DVI
Detachable
Off timer
Connector Type
Signal Cable Type
Physical
Dimensions & Weight:
Height (with base)
Characteristics Width
Depth
Weight (monitor only)
Environmental Temperature:
Operating
Non-Operating
Humidity:
Operating
Non-Operating
Altitude:
Operating
Non-Operating
379.4mm
498.3mm
189.2mm
3.45kg
0° to 40°
-25°to 55°
10% to 85% (non-condensing)
5% to 93% (non-condensing)
1 404 ft )
0~ 12192m (0~ 40000 ft )
I2369V
Panel
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Display Color
Dot Clock
Horizontal scan range
I2369V
TFT Color LCD
584.2mm Diagonal
0.0884*RGB(H)mm x 0.2652 (V)mm
R, G, B Analog lnterface ,DVI
H/V TTL
16.7M Colors
170MHz
30kHz to 83kHz
Horizontal scan Size(Maximum) 509.18
mm
Vertical scan range 50Hz to 76Hz
Vertical scan Size(Maximum) 286.42mm
Optimal preset resolution 1920×1080@60Hz
Resolution
Plug & Play
Input Connector
Input Video Signal
Power Source
Physical
Power Consumption
Off timer
Connector Type
Signal Cable Type
Dimensions & Weight:
Height (with base)
Characteristics Width
Depth
Weight (monitor only)
Environmental Temperature:
Operating
Non-Operating
Humidity:
Operating
Non-Operating
Altitude:
Operating
Non-Operating
VESA DDC2B/C1
VGA,DVI
Analog: 0.7Vp-p(standard),75 OHM,Positive,DVI
100-240V~, 50/60Hz
Active<30W(Typical)
Standby < 0.5 W
0-24 hrs
VGA, DVI
Detachable
398mm
531.4mm
204mm
3.75kg
0° to 40°
-25°to 55°
10% to 85% (non-condensing)
5% to 93% (non-condensing)
5 1 404 ft )
0~ 12192m (0~ 40000 ft )
I2369V
M
Panel
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Display Color
Dot Clock
Horizontal scan range
I2369V
M
TFT Color LCD
584.20mm Diagonal
0.0884*RGB(H)mm x 0.2652 (V)mm
R, G, B Analog lnterface ,HDMI ,MHL,DP
H/V TTL
16.7M Colors
170MHz
30kHz to 83kHz
Horizontal scan Size(Maximum) 509.18
mm
Vertical scan range 50Hz to 76Hz
Vertical scan Size(Maximum) 286.42mm
Optimal preset resolution
Resolution
Plug & Play
Input Connector
Input Video Signal
Power Source
1920×1080@60Hz
VESA DDC2B/C1
VGA,HDMI, DP
Power Consumption
Off timer
Connector Type
Signal Cable Type
Physical
Dimensions & Weight:
Height (with base)
Characteristics Width
Depth
Weight (monitor only)
Analog: 0.7Vp-p(standard),75 OHM,Positive,HDMI,MHL,DP
100-240V~, 50/60Hz
Active<35W(Typical)
Standby < 0.5 W
0-24 hrs
VGA, HDMI, DP
Detachable
398mm
531.4mm
204mm
3.80kg
Environmental Temperature:
Operating
Non-Operating
Humidity:
Operating
Non-Operating
Altitude:
Operating
Non-Operating
0° to 40°
-25°to 55°
10% to 85% (non-condensing)
5% to 93% (non-condensing)
1 404 ft )
0~ 12192m (0~ 40000 ft )
I2769V
Panel
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Display Color
Dot Clock
Horizontal scan range
I2769V
TFT Color LCD
686mm Diagonal
0.1038*RGB(H)mm x 0.3114 (V)mm
R, G, B Analog lnterface ,DVI
H/V TTL
16.7M Colors
170MHz
30kHz to 83kHz
Horizontal scan Size(Maximum) 597.888
mm
Vertical scan range 50Hz to 76Hz
Resolution
Vertical scan Size(Maximum) 336.312mm
Optimal preset resolution
Plug & Play
Input Connector
Input Video Signal
1920×1080@60Hz
VESA DDC2B/C1
VGA,DVI
Analog: 0.7Vp-p(standard),75 OHM,Positive,DVI
Power Source
Power Consumption
Off timer
Connector Type
Signal Cable Type
Physical
Dimensions & Weight:
Height (with base)
Characteristics Width
Depth
Weight (monitor only)
Environmental Temperature:
Operating
100-240V~, 50/60Hz
Active<30W(Typical)
Standby < 0.5 W
0-24 hrs
VGA, DVI
Detachable
448.8mm
621.9mm
213.2mm
4.90kg
Non-Operating
Humidity:
Operating
Non-Operating
Altitude:
Operating
Non-Operating
0° to 40°
-25°to 55°
10% to 85% (non-condensing)
5% to 93% (non-condensing)
1 404 ft )
0~ 12192m (0~ 40000 ft )
I2769V
M
Panel
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Display Color
Dot Clock
Horizontal scan range
I2769V
M
TFT Color LCD
686mm Diagonal
0.1038*RGB(H)mm x 0.3114 (V)mm
R, G, B Analog lnterface ,HDMI,MHL,DP
H/V TTL
16.7M Colors
170MHz
30kHz to 83kHz
Horizontal scan Size(Maximum) 597.888
mm
Vertical scan range 50Hz to 76Hz
Vertical scan Size(Maximum) 336.312mm
Optimal preset resolution
Resolution
Plug & Play
Input Connector
Input Video Signal
Power Source
1920×1080@60Hz
VESA DDC2B/C1
VGA,HDMI, DP
Analog: 0.7Vp-p(standard),75 OHM,Positive,HDMI,MHL,DP
Power Consumption
Off timer
Connector Type
Signal Cable Type
100-240V~, 50/60Hz
Active<35W(Typical)
Standby < 0.5 W
0-24 hrs
VGA, HDMI, DP
Detachable
Physical
Dimensions & Weight:
Height (with base)
Characteristics Width
Depth
Weight (monitor only)
Environmental Temperature:
Operating
448.8mm
621.9mm
213.2mm
5.0kg
0° to 40°
Non-Operating
Humidity:
Operating
Non-Operating
Altitude:
Operating
Non-Operating
-25°to 55°
10% to 85% (non-condensing)
5% to 93% (non-condensing)
1 404 ft )
0~ 12192m (0~ 40000 ft )
Preset Display Modes
STAND
Resolution
VGA
HORIZONTAL
FREQUENCY(kHZ)
VERTICAL
FREQUENCY(Hz)
640x480@75Hz 37.500 75.00
SVGA
IBM
MODE
DOS
MAC MODE
VGA
MAC MODE
SVGA
MAC MODE
X GA
XGA
1024x768@60Hz 48.363 60.004
1024x768@70Hz 56.476 70.069
1024x768@75Hz 60.023 75.029
1280x1024@60Hz 63.981 60.020
SXGA
1280x1024@75Hz 79.976 75.025
WXGA+ 1440x900@60Hz
WSXGA 1680x1050@60Hz
55.935
65.290
59.887
59.954
HD 1920x1080@60Hz 67.500 60.000
*** 1280x960@60HZ 60.000 60.000
1024x768@75Hz 60.241 74.927
10
11
12
13
14
15
6
7
4
5
8
2
3
Pin Number
1
9
HDMI timing
Format
Resolution
480p
576p
640 x 480
480p 720 x 480
720 x 576
60Hz
60Hz
50Hz
Vertical frequency
720p 1280 x 720 50Hz , 60Hz
1080i 1920 x 1080 50Hz , 60Hz
1080p 1920 x 1080 50Hz, 60Hz
MHL timing
480p
480p
576p
640 x 480
720 x 480
720 x 576
720p
1080i
1280 x 720
1920 x 1080
1080p
Pin Assignments
1920 x 1080
SD
SD
SD
HD
HD
HD
60Hz
60Hz
50Hz
50Hz , 60Hz
50Hz , 60Hz
30Hz
15-Pin Side of the Signal Cable
Video-Red
Video-Green
Video-Blue
N.C.
Detect Cable
GND-R
GND-G
GND-B
+5V
Ground
N.C.
DDC-Serial data
H-sync
V-sync
DDC-Serial clock
Pin No.
1
Signal Name
TMDS Data 2+
2
3
4
5
6
TMDS Data 2 Shield
TMDS Data 2
TMDS Data 1+
TMDS Data 1Shield
TMDS Data 1
7
8
TMDS Data 0+
TMDS Data 0 Shield
Pin No.
Signal Name
9 TMDS Data 0
10 TMDS Clock +
11 TMDS Clock Shield
12 TMDS Clock
13 CEC
14 Reserved (N.C. on device
15 SCL
16 SDA
Pin No.
Signal Name
17 DDC/CEC Ground
18 +5V Power
19 Hot Plug Detect
Pin Number
6
7
8
9
10
11
12
1
2
3
4
5
24-Pin Color Display Signal
Cable
TMDS data 2－
TMDS data 2＋
TMDS data 2/4 Shield
TMDS data 4－
TMDS data 4＋
DDC Clock
DDC Data
N.C.
TMDS data 1－
TMDS data 1＋
TMDS data 1/3 Shield
TMDS data 3－
Pin Number
18
19
20
21
13
14
15
16
17
22
23
24
24-Pin Color Display Signal
Cable
TMDS data 3＋
＋ 5V Power
Ground (for+5V)
Hot Plug Detect
TMDS data 0－
TMDS data 0＋
TMDS data 0/5 Shield
TMDS data 5－
TMDS data 5＋
TMDS Clock Shield
TMDS Clock +
TMDS Clock －
Plug and Play
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.
Regulation
FCC Notice
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
NOTICE :
The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference. It is the responsibility of the user to correct such interference.
CE Declaration of Conformity
T h is p rod u ct is in conformity w ith th e follow ing s tand ard s
• EN60950-1:2006 and A11+A1 (Safety requirement of Information Technology Equipment).
• EN 55022:2006+A1: 2007 (Radio Disturbance requirement of Information Technology Equipment).
• EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment).
• EN 61000-3-2:2006+A1: 2009+A2: 2009 (Harmonic current emissions).
• EN 61000-3-3:2008 (Voltage fluctuations & flicker) following provisions of directives applicable.
• 2006/95/EC (Low Voltage Directive).
• 2004/108/EC (EMC Directive).
• 2005/32/EC (EuP Directive, EC No. 1275/2008 mplementing Directive for Standby and Off mode power consumption) and is produced by a manufacturing organization on ISO9000 level.
WEEE Declaration
Disposal of Waste Equipment by Users in Private Household in the European Union.
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product .
WEEE /E-Waste declaration for India
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling in India, please visit the below web link.
www.aocindia.com/ewaste.php
Service
EU WARRANTY FOR AOC MONITORS
LIMITED THREE-YEAR WARRANTY*
For AOC LCD Monitors sold within Europe, AOC International (Europe) B.V. warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of consumer purchase. During this period, AOC International (Europe) B.V. will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as *stated below. In the absent of the proof of purchase, the warranty will start 3 months after the date of manufacturing indicated on the product.
If the product appears to be defective, please contact your local dealer or refer to the service and support section on www.aoc-europe.com for warranty instructions. Deliver the product freight pre-paid, along with the dated proof of purchase, to the AOC Certified or Authorized Service Center under the following condition:
•
Make sure the LCD Monitor is packed in a proper carton box (AOC prefers the original carton box to protects your monitor well enough during transport).
•
Put the RMA number on the address label
• Put the RMA number on the shipping carton
AOC International (Europe) B.V. is not responsible for any damaged during transport due to improper packing. AOC International (Europe) B.V. will pay the return shipping charges within one of the countries specified within this warranty statement. AOC International (Europe) B.V. is not responsible for any costs associated with the transportation of product across international borders. This includes the international border within the European Union. If the LCD Monitor is not available for collection when the currier attends, you will be charged a collection fee.
* This limited warranty does not cover any losses or damages that occur as a result of:
•
Improper installation or maintenance
•
Misuse
•
Neglect
•
Any cause other than ordinary commercial or industrial application
•
Adjustment by non-authorized source
•
Repair, modification, or installation of options or parts by anyone other than an AOC Certified or
Authorized Service Center
•
Improper environments like humidity and dusts
• Damaged by violence
•
Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or other irregularities
All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel policy standards.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A
PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE OF CONSUMER
PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD.
AOC INTERNATIONAL (EUROPE) B.V. OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE
SOLELY AND EXCULSIVELY AS STATED HERE. AOC INTERNATIONAL (EUROPE) B.V. LIABILITY,
WHETHER BASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR OTHER THEORY,
SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE
BASIS OF THE CLAIM. IN NO EVENT SHALL AOC INTERNATIONAL (EUROPE) B.V. BE LIABLE FOR
ANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT, OR OTHER INDIRECT,
INCIDENTAL, OR CONSEQUENTIAL DAMAGE. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY
NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
YOU MAY HAVE OTHER RIGHTS, WHICH MAY VARY FROM COUNTRY TO COUNTRY. THIS LIMITED
WARRANTY IS ONLY VALID FOR PRODUCTS PURCHASED IN THE MEMBER COUNTRIES OF THE
EUROPEAN UNION.
Warranty Statement for North & South America (excluding Brazil)
WARRANTY STATEMENT for AOC Color Monitors
Including those Sold within North America as Specified
Envision Peripherals, Inc. warrants this product to be free from defects in material and workmanship for a period of three (3) years for parts & labor and one (1) year for CRT Tube or LCD Panel after the original date of consumer purchase. During this period, EPI ( EPI is the abbreviation of Envision Peripherals, Inc. ) will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as *stated below. The parts or product that are replaced become the property of EPI.
In the USA to obtain service under this limited warranty, call EPI for the name of the Authorized Service Center closest to your area. Deliver the dated proof of purchase to the EPI Authorized Service Center.
If you cannot deliver the product in person:
Pack it in its original shipping container (or equivalent)
Put the RMA number on the address label
Put the RMA number on the shipping carton
Insure it (or assume the risk of loss/damage during shipment)
Pay all shipping charges
EPI is not responsible for damage to inbound product that was not properly packaged.
EPI will pay the return shipment charges within one of the countries specified within this warranty statement. EPI is not responsible for any costs associated with the transportation of product across international borders. This includes the international borders of the countries within this warranty statements.
In the United States and Canada contact your Dealer or EPI Customer Service, RMA Department at the toll free number (888) 662-9888. Or you can request an RMA Number online at www.aoc.com/na-warranty.
* This limited warranty does not cover any losses or damages that occur as a result of:
Shipping or improper installation or maintenance
Misuse
Neglect
Any cause other than ordinary commercial or industrial application
Adjustment by non-authorized source
Repair, modification, or installation of options or parts by anyone other than an EPI Authorized Service Center
Improper environment
Excessive or inadequate heating or air conditioning or electrical power failures, surges, or other irregularities
This three-year limited warranty does not cover any of the product's firmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for any such modification or alteration.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A
PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD PANEL
FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR
IMPLIED) APPLY AFTER THIS PERIOD. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY
NOT APPLY TO YOU.
EPI OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCLUSIVELY AS STATED HERE.
EPI’ LIABILITY, WHETHER BASED ON CONTRACT, TORT. WARRANTY, STRICT LIABILITY, OR OTHER
THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE
BASIS OF THE CLAIM. IN NO EVENT SHALL ENVISION PERIPHERALS, INC. BE LIABLE FOR ANY LOSS OF
PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT OR OTHER INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGE. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE LIMITATION
MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
In the United States of America, this limited warranty is only valid for Products purchased in the Continental United
States, Alaska, and Hawaii.
Outside the United States of America, this limited warranty is only valid for Products purchased in Canada.
Information in this document is subject to change without notice.
For more details, please visit:
USA: http://us.aoc.com/support/warranty
ARGENTINA: http://ar.aoc.com/support/warranty
BOLIVIA: http://bo.aoc.com/support/warranty
CHILE: http://cl.aoc.com/support/warranty
COLOMBIA: http://co.aoc.com/warranty
COSTA RICA: http://cr.aoc.com/support/warranty
DOMINICAN REPUBLIC: http://do.aoc.com/support/warranty
ECUADOR: http://ec.aoc.com/support/warranty
EL SALVADOR: http://sv.aoc.com/support/warranty
GUATEMALA: http://gt.aoc.com/support/warranty
HONDURAS: http://hn.aoc.com/support/warranty
NICARAGUA: http://ni.aoc.com/support/warranty
PANAMA: http://pa.aoc.com/support/warranty
PARAGUAY: http://py.aoc.com/support/warranty
PERU: http://pe.aoc.com/support/warranty
URUGUAY: http://pe.aoc.com/warranty
VENEZUELA: http://ve.aoc.com/support/warranty
IF COUNTRY NOT LISTED: http://latin.aoc.com/warranty
All AOC
branded
Only for AOC branded monitors sold within the continental United States.
monitors are now covered by the EASE Program. If your monitor malfunctions at any time
during the first three months, AOC will provide a replacement monitor within 72 hours after you are approved
for our program. If your monitor qualifies for the EASE program, AOC will pay for freight both ways.
Step 1:
Phone our TECH Department at 888.662.9888
Step 2:
Fill out and return EASE registration forms by mail or fax.
Step 3:
We will issue a Return Authorization Number upon verification into the program.
Step 4:
A monitor will be advance shipped to your location.
Step 5:
We will issue a UPS Call Tag to pick up the defective unit.
Step 6:
Please review the following chart to see your EASE program qualifications.
WARRANTY
PERIOD
Within the first three months of purchase: Covered by EASE
Between 4 months – 1 Year
Between 1 Year - 3 Years:
Covered by standard limited warranty
COVERAGE AT
NO CHARGE
- New AOC monitor
- Call tag dispatched and return freight
charges via UPS
- All Parts & Labor Including CRT
Tube & LCD Panel
- Parts & Labor (excluding CRT Tube
& LCD Panel)
CUSTOMER
CHARGES
- None*
- UPS Return Freight to AOC
- UPS Return Freight to AOC
*AOC will need to obtain a credit card number if you would like to get a new AOC monitor advanced shipped to your location, prior to the defective unit
arriving at AOC’s service center. If you do not wish to supply a credit card, AOC will only ship the new monitor, once the defective unit arrives at the AOC
service center.
us .aoc.com
Congratulations!
This product is designed for both you and the planet!
TCO Development works for sustainable IT - manufacture, use and recycling of IT products reflecting environmental, social and economic responsibility.
TCO Certified is a third party verified program, where every product model is tested by an accredited impartial test laboratory. TCO
Certified represents one of the toughest certifications for ICT products worldwide.
Some of the Usability features of TCO Certified Displays:
Visual Ergonomics for image quality is tested to ensure top performance and reduce sight and strain problems. Important parameters are Resolution,
Luminance, Contrast, Reflection and Colour characteristics
Products are tested according to rigorous safety standards at impartial laboratories
Electric and magnetic fields emissions as low as normal household background levels
Workload ergonomics to ensure a good physical environment
Some of the Environmental features of TCO Certified Displays:
Production facilities have an Environmental Management System (EMAS or ISO
14001)
Low energy consumption to minimize climate impact
Restrictions on Chlorinated and Brominated flame retardants, plasticizers, plastics and heavy metals such as cadmium, mercury and lead (RoHS compliance)
Both product and product packaging is prepared for recycling
The brand owner offers take-back options
Corporate Social Responsibility
The brand owner demonstrates the product is manufactured under working practices that promote good labour relations and working conditions.
The Criteria Document can be downloaded from our web site. The criteria included in this label have been developed by TCO Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s
TCO has been involved in influencing the development of IT equipment in a more user and environmentally friendly direction. Our ICT product labeling system began in
1992 and is now requested by users and ICT-manufacturers all over the world.
For more information, please visit
www.tcodevelopment.com
TCO Certified Document for Displays version. 2.3
advertisement
Key Features
- Home 54.6 cm (21.5") LED IPS
- Full HD 1920 x 1080 pixels 16:9
- 60 Hz 5 ms 250 cd/m² 1000:1
- 23 W