ASRock IMB-140 Motherboard Rýchly sprievodca

Motherboard Layout

5

6

7

8

1

2

3

4

SET COM Ports 1,2 (SET_CM1,2)

LVDS Con (LVDS1)

4-Pin DC PWR (DC12V1)

CPU Fan Connector (CPU_FAN1)

2 x DDR3 DIMM Slots

Chassis Fan Connector (CHA_FAN1)

Output Power (SATA_PWR1)

SATA2 Connector (SATA2_1, Blue)

9

10

11

12

Printer Port Header (LPT1)

SATA2 Connector (SATA2_2, Blue)

USB 2.0 Ports 4,5 (USB4,5)

USB 2.0 Port 6 (USB6)

13 Digital I/O Header (JGPIO1)

14 Digital I/O Header PWR Setting

(JGPIO_PWR1)

15 System Panel Control Header (PANEL1)

16

17

Clear CMOS Header (CLRCMOS1)

PWR-On mode Setting (PWR_JP1)

22

23

18

19

20

21

SPI Flash Memory (16Mb)

COM Ports 4,5,6 (COM4,5,6)

SET COM Ports 4,5,6 (SET_CM4,5,6)

Panel Brightness and Speaker Volume

Control (BLT_VOL1)

Panel Backlight Inverter connector

(BLT_PWR2)

Speaker Connector (SPEAKER1)

24

25

26

27

PCI1

Front Panel Audio Header (HD_AUDIO1)

Panel VDD PWR Setting (PNL_PWR1)

Panel Backlight PWR Setting

28

(BKT_PWR1)

Bottom Side CF Card PWR Setting

(JCFPWR1)

29 Panel Resolution Selection

30

(JLVD_GPIO1)

SET COM Port 3 (SET_CM3)

1

Onboard Headers, Connectors and Jumpers

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.

Clear CMOS Jumper

(CLRCMOS1)

(see p.1, No. 16)

Default Clear CMOS

Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action.

Please be noted that the password, date, time, user default profile and MAC address will be cleared only if the CMOS battery is removed.

Digital I/O Header PWR Setting

(3-pin JGPIO_PWR1)

(see p.1 No. 14)

PWR-On Mode Setting

(3-pin PWR_JP1)

(see p.1 No. 17)

1-2: +12V.

2-3: +5V.

1-2: AT Mode.

2-3: ATX Mode.

Panel VDD PWR Setting

(3-pin PNL_PWR1)

(see p.1 No. 26)

1-2: +3.3V.

2-3: +5V.

2

Panel BackLight PWR Setting

(3-pin BKT_PWR1)

(see p.1 No. 27)

1-2: +5V.

2-3: +12V.

Bottom Side CF Card PWR Setting

(3-pin JCFPWR1)

(see p.1 No. 28)

1-2: +3.3V.

2-3: +5V.

Panel Resolution Selection

(12-pin JLVD_GPIO1)

(see p.1 No. 29)

Reserved.

Default set by BIOS.

3

2.8 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

SATA2 Connectors

(SATA2_1: see p.1, No. 8)

(SATA2_2: see p.1, No. 10)

SATA2_1 SATA2_2

These two Serial ATA2

(SATA2) connectors support

SATA data cables for internal storage devices. The current

SATA2 interface allows up to

3.0 Gb/s data transfer rate.

USB 2.0 Ports

(4-pin USB4,5)

(see p.1 No. 11)

1

PWR -4 +4 GND

7

2

PWR -5 +5 GND

8

Besides four default USB 2.0 ports on the I/O panel, there are three USB 2.0 ports on this motherboard.

(4-pin USB6)

(see p.1 No. 12) 1

PWR -6 +6 GND

4

System Panel Header

(9-pin PANEL1)

This header accommodates several system front panel

(see p.1 No. 15) functions.

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch.

4

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

Speaker Connector

(4-pin SPEAKER 1)

(see p.1 No. 23)

Front Panel Audio Header

(9-pin HD_AUDIO1)

(see p.1 No. 25)

1

R+ L-

R- L+

4

1: Speaker R-

2: Speaker R+

3: Speaker L+

4: Speaker L-

This is an interface for front panel audio cable that allows convenient connection and control of audio devices.

1. High Definition Audio supports Jack Sensing, but the panel wire on

the chassis must support HDA to function correctly. Please follow the

instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio

header as below:

A. Connect Mic_IN (MIC) to MIC2_L.

B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C. Connect Ground (GND) to Ground (GND).

D. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

5

E. To activate the front mic.

For Windows ® XP / XP 64-bit OS:

Select “Mixer”. Select “Recorder”. Then click “FrontMic”.

For Windows ® 7 / 7 64-bit / Vista TM / Vista TM 64-bit OS:

Go to the “FrontMic” Tab in the Realtek Control panel. Adjust

“Recording Volume”.

Chassis Fan Connector

(3-pin CHA_FAN1)

(see p.1 No. 6)

Please connect the fan cable to the fan connector and match the black wire to the ground pin.

CPU Fan Connector

(4-pin CPU_FAN1)

(see p.1 No. 4)

Please connect the CPU fan cable to the connector and match the black wire to the ground pin.

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin

CPU fan still can work successfully even without the fan speed control function.

If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this

motherboard, please connect it to Pin 1-3.

Pin 1-3 Connected

3-Pin Fan Installation

DC 12V Power Connector

(4-pin DC12V1)

(see p.1 No. 3)

COM port 4,5,6

(10-pin COM4,5,6)

(see p.1 No. 19)

12V

GND

12V

GND

Please connect a DC 12V power supply to this connector.

6

SET COM Ports

(10-pin SET_CM1,2)

(see p.1 No. 1)

(10-pin SET_CM4,5,6)

(see p.1 No. 20)

(5-pin SET_CM3)

(see p.1 No. 30)

1

LVDS Con

(40-pin LVDS1)

(see p.1 No. 2)

Output Power

(4-pin SATA_PWR1)

(see p.1 No. 7)

1

2

3

4

1: +5V

2, 3: GND

4. +12V

7

Printer Port Header

(25-pin LPT1)

(see p.1 No. 9)

Digital I/O Header

(10-pin JGPIO1)

(see p.1 No. 13)

PIN Signal Name PIN Signal Name

1 Digital Output 0 2 Digital Input 0

3 Digital Output 1 4 Digital Input 1

5 Digital Output 2 6 Digital Input 2

7 Digital Output 3 8 Digital Input 3

9 PWR 10 GND

Panel Brightness and

Speaker Volume Control

(7-pin BLT_VOL1)

(see p.1 No. 21)

1

Panel BackLight Inverter connector

(6-pin BLT_PWR2)

(see p.1 No. 22)

RJ-45 COM Port C

(8-pin COM Port C)

7

1: Volume_UP

2: Volume_DOWN

3: PANEL PWR Down

4: Panel BackLight UP

5: Panel BackLight Down

6: GND

7: GND

1,2: Panel Backlight Power

3: Panel Backlight Enable

4: Panel Backlight Control

5,6: GND

1: DCD#

2: RXD

4: DTR#

5: GND

6: DSR#

7: RTS#

8: CTS#

8