A780L3C Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies.

Dichiarazione di conformità sintetica

Ai sensi dell’art. 2 comma 3 del D.M.

275 del 30/10/2002

Si dichiara che questo prodotto è conforme alle normative vigenti e soddisfa i requisiti essenziali richiesti dalle direttive

2004/108/CE, 2006/95/CE e

1999/05/CE quando ad esso applicabili

Short Declaration of conformity

We declare this product is complying with the laws in force and meeting all the essential requirements as specified by the directives

2004/108/CE, 2006/95/CE and

1999/05/CE whenever these laws may be applied

Table of Contents

Chapter 1: Introduction.......................................... 3

1.1

Before You Start ................................................................................3

1.2

1.3

1.4

1.5

Package Checklist ............................................................................3

Motherboard Specifications .............................................................4

Rear Panel Connectors ....................................................................5

Motherboard Layout ..........................................................................6

Chapter 2: Hardware Installation ........................... 7

2.1

Install Central Processing Unit (CPU) ............................................7

2.2

2.3

Install a Heatsink ...............................................................................8

Connect Cooling Fans ......................................................................9

2.4

2.5

Installing System Memory ..............................................................10

Expansion Slots ...............................................................................12

2.6

2.7

Jumper Setting ................................................................................13

Headers & Connectors ...................................................................14

Chapter 3: BIOS & Software ................................. 18

3.1

BIOS Setup ......................................................................................18

3.2

BIOS Update ....................................................................................18

3.3

Software ............................................................................................23

Chapter 4: Useful Help ......................................... 26

4.1

Driver Installation .............................................................................26

4.2

4.3

Troubleshooting ...............................................................................27

RAID Functions ...............................................................................29

Appendix: Specifications In Other Languages ...... 32

German .................................................................................................................32

French ...................................................................................................................34

Italian .....................................................................................................................36

Spanish ..................................................................................................................38

Portuguese ...........................................................................................................40

Polish .....................................................................................................................42

Russian .................................................................................................................44

Arabic .....................................................................................................................46

Japanese ...............................................................................................................48

A780L3C

CHAPTER 1: INTRODUCTION

1.1 Before You Start

Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below:

„ Prepare a dry and stable working environment with sufficient lighting.

„ Always disconnect the computer from power outlet before operation.

„ Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge.

„ Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board.

„ Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment.

„ Keep the computer from dangerous area, such as heat source, humid air and water.

„ The operating temperatures of the computer should be 0 to

45 degrees Celsius.

„ To avoid injury, be careful of:

Sharp pins on headers and connectors

Rough edges and sharp corners on the chassis

Damage to wires that could cause a short circuit

; Serial ATA Cable x2

; Rear I/O Panel for ATX Case x1

; Installation Guide x1

; Fully Setup Driver DVD x1

Note: The package contents may be different due to the sales region or models in which it was sold.

For more information about the standard package in your region, please contact your dealer or sales representative.

3

Motherboard Manual

4

CPU

FSB

Chipset

Super I/O

Main

Memory

Graphics

SATA II

LAN

Sound

Slots

SPEC

Socket AM3

AMD Sempron / Phenom II / Athlon II processors

(Maximum Watt: 95W)

AMD 64 Architecture enables 32 and 64 bit computing

Supports Hyper Transport 2.0

Support Hyper Transport 3.0

Supports up to 3.2 GT/s Bandwidth

AMD 760G

AMD SB710

ITE 8728F-BX

Provides the most commonly used legacy Super

I/O functionality

Low Pin Count Interface

Environment Control initiatives

H/W Monitor

ITE's "Smart Guardian" function

DDR3 DIMM Slots x 2

Max Memory Capacity 16GB

Each DIMM supports 512MB/1GB/

2GB/4GB/8GB DDR3

Integrated in AMD 760G Chipset

Dual Channel Mode DDR3 memory module

Supports DDR3 800/1066/1333/1600(OC)

Registered DIMM and ECC DIMM is not supported

Integrated Serial ATA Controller

Realtek RTL 8105T

Max Shared Video Memory is 1024MB

Data transfer rates up to 3 Gb/s

SATA Version 2.0 specification compliant

10 / 100 Mb/s auto negotiation

VT1708B / ALC662

PCI Express X16 slot

PCI slot

On Board

Connectors

SATA Connector

IDE Connector

Front Panel Connector

Front Audio Connector

CPU Fan Header x1 x1 x4 x1 x1 x1 x1

5.1 channels audio out

High Definition Audio

Supports PCI-E X16 expansion card

Supports PCI expansion cards

Each connector supports 1 SATA device

Each connector supports 2 IDE device

Supports front panel facilities

Supports front panel audio function

CPU Fan power supply (with Smart Fan function)

System Fan Header

CMOS Clear Jumper

USB Connector

Power Connector (24pin)

Power Connector (4pin)

A780L3C x1

SPEC

System Fan Power supply x1 x2 x1 x1

Restore CMOS data to factory default setting

Each connector supports 2 front panel USB ports

Connects to Power supply

Connects to Power supply

Printer Port Connector

PS/2 Keyboard

PS/2 Mouse

Back Panel

I/O

VGA port

LAN port x1 x1 x1 x1 x1

Each connector supports 1 Printer port

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to D-SUB monitor

Connect to RJ-45 Ethernet cable

USB Port

Audio Jack

Board Size 182 mm(W) x 225 mm(L)

Special

Features

RAID 0 / 1 / 10 support x4 x3

Connect to USB devices

Provide Audio-In/Out and microphone connection

Biostar reserves the right to add or remove support for any

OS Support Windows XP / Vista / 7 / 8

OS With or without notice.

1.4 Rear Panel Connectors

5

Motherboard Manual

Note: ■ represents the 1st pin.

6

CHAPTER 2: HARDWARE INSTALLATION

2.1 Install Central Processing Unit (CPU)

Step 1: Locate the CPU socket on the motherboard

A780L3C

Step 2: Pull the socket locking out from the socket and then raise the lever up to a

90-degree angel.

Step 3: Look for the white triangle on socket, and the gold triangle on CPU should point towards this white triangle. The CPU will fit only in the correct orientation.

182 mm (幅 ) to prevent damaging the CPU.

7

Motherboard Manual

Step 4: Hold the CPU down firmly, and then close the lever to locked the position

Step 1: Place the heatsink and fan assembly onto the retention frame. Match the heatsink clip with the socket mounting-lug. Hook the spring clip to the mounting-lug.

Step 2: On the other side, push the retention clip straight down to lock into the plastic lug on the retention frame, and then press down the locker until it stops.

8

Note1: Do not forget to connect the CPU fan connector.

Note2: For proper installation, please kindly refer to the installation manual of your CPU heatsink.

A780L3C

These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.

CPU_FAN1: CPU Fan Header

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

4 Smart Fan Control

(By Fan)

SYS_FAN1: System Fan Header

Pin Assignment

1

2

3

Ground

+12V

FAN RPM rate sense

Note: CPU_FAN1, SYS_FAN1 support 4-pin and 3-pin head connectors. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to

GND.

9

Motherboard Manual

2.4 Installing System Memory

A. DDR3 Memory Modules

Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

Step 2: Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.

10

Note: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.

A780L3C

B. Memory Capacity

DIMM Socket

Location

DDR3 Module

DDR3_A1 512MB/1GB/2GB/4GB/8GB

DDR3_B1 512MB/1GB/2GB/4GB/8GB

Total Memory

Size

Max is 16GB.

C. Dual Channel Memory installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status DDR3_A1 DDR3_B1

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or x16)

11

Motherboard Manual

PEX16_1: PCI-Express X16 Slot

-

-

-

PCI-Express 2.0 compliant.

Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, for an aggregate of 8GB/s totally.

PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

12

PCI1: Peripheral Component Interconnect Slot

This motherboard is equipped with 1 standard PCI slot. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits.

A780L3C

The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”.

JCMOS1: Clear CMOS Jumper

Placing the jumper on pin2-3 allows user to restore BIOS safe setting and

CMOS data. Pease carefully follow the procedures to avoid damaging the motherboard.

1 3

※ Clear CMOS Procedures:

1.

2.

3.

4.

Remove AC power line.

Set the jumper to “Pin 2-3 close”.

Wait for five seconds.

Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Load Optimal Defaults and save settings in CMOS.

Pin 1-2 Close:

Normal Operation

(default).

1 3

Pin 2-3 Close:

Clear CMOS data.

13

Motherboard Manual

2.7 Headers & Connectors

ATXPWR1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX power supply.

14

Pin Assignment

13 +3.3V

14 -12V

15 Ground

16 PS_ON

17 Ground

18 Ground

19 Ground

20 NC

21 +5V

22 +5V

23 +5V

24 Ground

1 +3.3V

2 +3.3V

3 Ground

4 +5V

5 Ground

6 +5V

7 Ground

8 PW_OK

Voltage+5V

11 +12V

ATXPWR2: ATX Power Source Connector

This connector provides +12V to CPU power circuit.

Pin Assignment

1 +12V

2 +12V

3 Ground

4 Ground

Note1: Before you power on the system, please make sure that both ATXPWR1 and

ATXPWR2 connectors have been plugged-in.

Note2: Insufficient power supplied to the system may result in instability or the peripherals not functioning properly. Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices.

A780L3C

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.

5

6

3

4

7

8

Pin

1

2

Speaker

HDD LED (+)

HDD LED (-)

Reset control

Hard drive

LED

10

12

13

14

16

Assignment Function

N/A

Power LED (+)

Power LED (+)

Power LED (-)

Ground

Power LED

SATA1~SATA4: Serial ATA Connectors

These connectors connect to SATA hard disk drives via SATA cables. It satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.

Pin Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

7 Ground

15

Motherboard Manual

IDE1: Hard Disk Connector

The motherboard has a 32-bit Enhanced IDE Controller that provides PIO Mode

0~4, Bus Master, Multi-word DMA, and Ultra DMA 33/66/100/133 functionality.

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

These headers allow user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader.

Pin Assignment

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 NC

10 Key

16

A780L3C

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable.

Pin Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

8 Key

9 Left line in

J_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

6 -Init 19

2 20 Ground

8 -Scltin 21 Busy

10 Ground 23 PE

4 24 Ground

12 Ground 25 SCLT

17

Motherboard Manual

CHAPTER 3: BIOS & SOFTWARE

„ For better system performance, the BIOS firmware is being continuously updated. The BIOS information described below in this manual is for your reference only and the actual BIOS information and settings on board may be different from this manual

„ For further information of setting up the BIOS, please refer to the BIOS

Manual in the Setup DVD.

There are three ways to update the BIOS:

BIOS Update Utility, BIOS Online Update Utility and BIOS Flasher.

1. BIOS Update Utility

1. Installing BIOS Update Utility from the DVD Driver.

2. Download the proper BIOS from www.biostar.com.tw

.

Show current BIOS information

AWARD BIOS AMI BIOS

Clear CMOS function

(Only for AWARD BIOS)

Save current BIOS to a .bin file

Update BIOS with a BIOS file

18

A780L3C

<Backup BIOS>

Once click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be

English/number and no longer than 7 characters.) Then click Save.

After the saving process, finish dialog will show. Click on OK to complete the

BIOS Backup procedure.

<Update BIOS>

Before doing this, please download the proper BIOS file from the website.

For AWARD BIOS, update BIOS procedure should be run with Clear

CMOS function, so please check on

Clear CMOS first.

Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure.

After the BIOS Backup procedure, the open dialog will show for requesting the

BIOS file which is going to be updated.

Please choose the proper BIOS file for updating, then click on Open.

19

Motherboard Manual

The utility will update BIOS with the proper BIOS file, and this process may take minutes. Please do not open any other applications during this process.

After the BIOS Update process, click on

OK to restart the system.

While the system boots up and the full screen logo shows, press key to enter BIOS setup.

<Delete>

In the BIOS setup, use the Load Optimized Defaults function and then Save and

Exit Setup to exit BIOS setup. BIOS Update is completed.

2. Online Update Utility

1. Installing BIOS Update Utility from the DVD Driver.

2. Please make sure the system is connected to the internet before using this function.

3. Open BIOS Update Utility and click the Online Update button on the main screen.

4. An open dialog will show up to request your agreement to start the BIOS update. Click

Yes to start the online update procedure.

20

A780L3C

5. If there is a new BIOS version, the utility will ask you to download it. Click Yes to proceed.

6. After the download is completed, you will be asked to program (update) the BIOS or not. Click Yes to proceed.

7. After the updating process is finished, you will be asked you to reboot the system. Click

OK to reboot.

8. While the system boots up and the full screen logo shows up, press

<Delete> key to enter BIOS setup.

After entering the BIOS setup, please go to the Save & Exit, using the Restore

Defaults function to load Optimized Defaults, and select Save Changes and

Reset to restart the computer. Then, the BIOS Update is completed.

21

Motherboard Manual

3. BIOSTAR BIOS Flasher

BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and simple way to update your BIOS via USB pen drive.

Note1: This utility only allows storage device with FAT32/16 format and single partition.

Note2: Shutting down or resetting the system while updating the BIOS will lead to system boot failure.

The BIOSTAR BIOS Flasher is built in the BIOS ROM. To enter the utility, press

<F12> during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIOSTAR BIOS Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the USB port or the floppy disk drive.

4. Power on or reset the computer and then press <F12> during the POST process. A select dialog as the picture on the right appears. Select the device contains the

BIOS file and press <Enter> to enter the utility.

5. The utility will show the BIOS files and their respective information. Select the proper BIOS file and press <Enter> then <Y> to perform the BIOS update process.

6. After the update process, the utility will ask you to reboot the system.

Press <Y> to proceed.

BIOS update completes.

22

A780L3C

3.3 Software

Installing Software

1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled.

3. Follow the on-screen instructions to complete the installation.

Note1: All the information and content about following software are subject to be changed without notice. For better performance, the software is being continuously updated.

Note2: The information and pictures described below are for your reference only. The actual information and settings on board may be slightly different from this manual.

Launching Software

After the installation process, you will see the software icon “eHOT Line” / “BIOS

Update” appears on the desktop. Double-click the icon to launch the utility.

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our Tech-Support system.

This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem.

Note: Before you use this utility, please set Outlook Express as your default e-mail client application program.

* must provide. Without this information, you may not be able to send out the mail.

This block will show the information which would be collected in the mail.

* Describe condition of your system.

* Select your area or the area close to you.

Provide the e-mail address that you would like to send the copy to.

* Provide the name of the memory module manufacturer.

Send the mail out.

Exit this dialog.

Save these information to a .txt file

Provide the name of the power supply manufacturer and the model no.

23

Motherboard Manual

After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click

“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name.

Enter the file name and then click “Save”.

Your system information will be saved to a .txt file.

Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail.

Note1: We will not share customer’s data with any other third parties, so please feel free to provide your system information while using eHot-Line service.

Note2: If you are not using Outlook Express as your default e-mail client application, you may need to save the system information to a .txt file and send the file to our tech support with other e-mail application. Go to the following web http://www.biostar.com.tw/app/en/about/contact.php

for getting our contact information.

24

A780L3C

BIOScreen Utility (Optional)

This utility allows you to personalize your boot logo easily. You can choose

BMP as your boot logo so as to customize your computer.

Please follow the following instructions to update boot logo:

1. Load Image：Choose the picture as the boot logo.

2. Transform：Transform the picture for BIOS and preview the result.

3. Update Bios：Write the picture to BIOS Memory to complete the update.

25

Motherboard Manual

CHAPTER 4: USEFUL HELP

After you installed your operating system, please insert the Fully Setup Driver

DVD into your optical drive and install the driver for better system performance.

You will see the following window after you insert the DVD

The setup guide will auto detect your motherboard and operating system.

Note: If this window didn’t show up after you insert the Driver DVD, please use file browser to locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver DVD.

Click on the Manual icon to browse for available manual.

Note: You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://get.adobe.com/reader/

26

A780L3C

4.2 Troubleshooting

Probable Solution

1. There is no power in the system.

Power LED does not shine; the fan of the power supply does not work

2. Indicator light on keyboard does not shine.

System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running.

System does not boot from a hard disk drive, but can be booted from optical drive.

System only boots from an optical drive. Hard disks can be read, applications can be used, but system fails to boot from a hard disk.

1. Make sure power cable is securely plugged in.

3. Contact technical support.

Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place.

1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup.

2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time.

1. Back up data and applications files.

2. Reformat the hard drive.

Re-install applications and data using backup disks.

Screen message shows “Invalid

Configuration” or “CMOS Failure.”

Review system’s equipment. Make sure correct information is in setup.

System cannot boot after user installs a second hard drive.

1. Set master/slave jumpers correctly.

2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives.

27

Motherboard Manual

CPU Overheated

If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.

(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

28

A780L3C

Operating System

z Supports Windows XP, Windows Vista, and Windows 7.

Raid Arrays

RAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications.

RAID 1: RAID 1 defines techniques for mirroring data.

RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1.

How RAID Works

RAID 0:

The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

- Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the platform.

- Uses: Intended for non-critical data requiring high data throughput, or any environment that does not require fault tolerance.

- Benefits: provides increased data throughput, especially for large files.

No capcity loss penalty for parity.

- Drawbacks: Does not deliver any fault tolerance. If any drive in the array fails, all data is lost.

- Fault Tolerance: No.

- Total Capacity: (Minimal. HDD Capacity) x (Connected HDDs Amount)

Block 1

Block 3

Block 5

Block 2

Block 4

Block 6

29

Motherboard Manual

RAID 1:

Every read and write is actually carried out in parallel across 2 disk drives in a

RAID 1 array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure.

RAID techniques can be applied for high-availability solutions, or as a form of automatic backup that eliminates tedious manual backups to more expensive and less reliable media.

Features and Benefits

- Drives: Minimum 2, and maximum is 2.

- Uses: RAID 1 is ideal for small databases or any other application that requires fault tolerance and minimal capacity.

- Benefits: Provides 100% data redundancy. Should one drive fail, the controller switches to the other drive.

- Drawbacks: Requires 2 drives for the storage space of one drive.

Performance is impaired during drive rebuilds.

- Fault Tolerance: Yes.

Block 1

Block 2

Block 3

Block 1

Block 2

Block 3

30

A780L3C

RAID 10:

RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 10 solution for improved resiliency, performance and rebuild performance.

Features and Benefits

- Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.

- Benefits: Optimizes for both fault tolerance and performance, allowing for automatic redundancy. May be simultaneously used with other RAID levels in an array, and allows for spare disks.

- Drawbacks: Requires twice the available disk space for data redundancy, the same as RAID level 1.

- Fault Tolerance: Yes.

Block 1

Block 3

Block 5

Block 1

Block 3

Block 5

Block 2

Block 4

Block 6

Block 2

Block 4

Block 6

31

Motherboard Manual

APPENDIX: Specifications In Other Languages

German

Spezifikationen

Sockel AM3 Die AMD 64-Architektur unterstützt eine 32-Bit- und

CPU AMD Sempron / Phenom II / Athlon II

Prozessoren (Maximales Watt: 95W)

64-Bit-Datenverarbeitung

Unterstützt Hyper Transport 2.0

FSB

Chipsatz

Unterstützt Hyper Transport 3.0 mit einer

Bandbreite von bis zu 3.2 GT/s

AMD 760G

AMD SB710

Super E/A

ITE8728F-BX

Bietet die häufig verwendeten alten Super

E/A-Funktionen.

Low Pin Count-Schnittstelle

Umgebungskontrolle,

Hardware-Überwachung

"Smart Guardian"-Funktion von ITE

DDR3 DIMM-Steckplätze x 2

Arbeitsspeiche Max. 16GB Arbeitsspeicher r

Jeder DIMM unterstützt 512MB/1GB/

2GB/4GB/8GB DDR3.

Grafik Integrierter AMD 760G-Chipsatz

Dual-Kanal DDR3 Speichermodul

Unterstützt DDR3 800/1066/1333/1600(OC) registrierte DIMMs. ECC DIMMs werden nicht unterstützt.

SATA Integrierter Serial ATA-Controller

Max. 1024MB gemeinsam benutzter Videospeicher

Datentransferrate bis zu 3 Gb/s

Konform mit der SATA-Spezifikation Version 2.0.

LAN Realtek RTL 8105T

HD

Audio-Unterstü VT1708B / ALC662 tzung

10 / 100 Mb/s Auto-Negotiation

5.1-Kanal-Audioausgabe

Unterstützt High-Definition Audio

PCI Express X16 Steckplatz x1

Steckplätze

PCI-Steckplatz x1

Onboard-Ansc SATA-Anschluss hluss

IDE-Anschluss x4 x1

Jeder Anschluss unterstützt 1 SATA-Laufwerk

Jeder Anschluss unterstützt 2 IDE-Laufwerke

32

A780L3C

"CMOS löschen"-Sockel

Spezifikationen

CPU-Lüfterstromversorgungsanschluss (mit Smart

CPU-Lüfter-Sockel x1

Fan-Funktion) x1

Stromanschluss (24-polig)

Stromanschluss (4-polig) x1 x1

Druckeranschluss Anschluss x1 unterstützt 1 Druckeranschluss

PS/2-Tastatur x1

PS/2-Maus x1

Rückseiten-E/

A

VGA-Anschluss x1

LAN-Anschluss x1

USB-Anschluss x4

Audioanschluss x3

Platinengröße 182 mm (B) X 225 mm (L)

Sonderfunktion

Unterstützt RAID 0 / 1 / 10 en

OS-Unterstütz ung

Windows XP / Vista / 7 / 8

Biostar behält sich das Recht vor, ohne Ankündigung die

Unterstützung für ein Betriebssystem hinzuzufügen oder zu entfernen.

33

Motherboard Manual

French

SPEC

UC

Socket AM3

Processeurs AMD Sempron / Phenom II /

Athlon II (Watt maximum : 95W)

Bus frontal

Chipset

Prend en charge Hyper Transport 3.0 jusqu'à une bande passante de 3.2 GT/s

AMD 760G

AMD SB710

L'architecture AMD 64 permet le calcul 32 et 64 bits

Prend en charge Hyper Transport 2.0

Super E/S

ITE 8728F-BX

Fournit la fonctionnalité de Super E/S patrimoniales la plus utilisée.

Interface à faible compte de broches

Initiatives de contrôle environnementales,

Moniteur de matériel

Fonction "Gardien intelligent" de l'ITE

Mémoire principale

Fentes DDR3 DIMM x 2

Capacité mémoire maximale de 16Go

Module de mémoire DDR3 à mode à double voie

Prend en charge la DDR3 800/1066/1333/1600(OC)

Chaque DIMM prend en charge des DDR3 de Les DIMM à registres et DIMM avec code correcteurs

512Mo/1Go/2Go/4Go/8Go d'erreurs ne sont pas prises en charge

Graphiques Integré dans la chipset AMD 760G Mémoire vidéo partagée maximale de 1024 Mo

SATA Contrôleur Serial ATA intégré

LAN Realtek RTL 8105T

Prise en charge audio VT1708B / ALC662

HD

Fente PCI Express X16

Fentes

Fente PCI

Connecteur embarqué

Connecteur SATA

Connecteur IDE

Connecteur du panneau avant

Connecteur Audio du panneau avant x1 x1 x1 x1 x4 x1

Taux de transfert jusqu'à 3 Go/s.

Conforme à la spécification SATA Version 2.0

10 / 100 Mb/s négociation automatique

Sortie audio à 5.1 voies

Prise en charge de l'audio haute définition

Chaque connecteur prend en charge 1 périphérique SATA

Chaque connecteur prend en charge 2 périphériques IDE

Prend en charge les équipements du panneau avant

Prend en charge la fonction audio du panneau avant

34

Embase de ventilateur UC

Embase de ventilateur système

Embase d'effacement CMOS

Connecteur USB

Connecteur d'alimentation

(24 broches)

Connecteur d'alimentation

(4 broches)

Connecteur de Port d'imprimante

Clavier PS/2

Souris PS/2

E/S du panneau arrière

Port VGA

Port LAN

Port USB

Fiche audio

Dimensions de la carte

182 mm (l) X 225 mm (H)

Fonctionnalit

és spéciales

Prise en charge RAID 0 / 1 / 10

Support SE Windows XP / Vista / 7 / 8

A780L3C x1

SPEC

Alimentation électrique du ventilateur UC (avec fonction de ventilateur intelligent) x1 x1 x2

Alimentation électrique du ventilateur système

Chaque connecteur prend en charge 2 ports USB de panneau avant x1 x1 x1 x1 x1 x1 x1 x4 x3

Chaque connector prend en charge 1 Port d'imprimante

Biostar se réserve le droit d'ajouter ou de supprimer le support de SE avec ou sans préavis.

35

Motherboard Manual

Italian

CPU

Socket AM3

Processori AMD Sempron / Phenom II /

SPECIFICA

L’architettura AMD 64 abilita la computazione 32 e 64 bit

FSB

Athlon II (Watt massimo: 95W)

Supporto di HyperTransport 3.0 fino a 3.2

GT/s di larghezza di banda

Supporto di Hyper Transport 2.0

Chipset

AMD 760G

AMD SB710

Super I/O

Interfaccia LPC (Low Pin Count)

ITE 8728F-BX

Fornisce le funzionalità legacy Super I/O

Monitoraggio hardware usate più comunemente.

Funzioni di controllo dell’ambiente:

Funzione "Smart Guardian" di ITE

Alloggi DIMM DDR3 x 2

Memoria principale

Capacità massima della memoria 16GB

Ciascun DIMM supporta DDR3

Modulo di memoria DDR3 a canale doppio

Supporto di DDR3 800/1066/1333/1600(OC)

DIMM registrati e DIMM ECC non sono supportati

512MB/1GB/2GB/4GB/8GB

Grafica Integrata nel Chipset AMD 760G La memoria video condivisa massima è di 1024 MB

Velocità di trasferimento dei dati fino a 3 Gb/s.

SATA Controller Serial ATA integrato

LAN Realtek RTL 8105T

Supporto audio HD

VT1708B / ALC662

Compatibile specifiche SATA Versione 2.0.

Negoziazione automatica 10 / 100 Mb/s

Uscita audio 5.1 canali

Alloggio PCI Express X16

Alloggi

Alloggio PCI

Connettori su scheda

Connettore SATA

Connettore IDE x1 x1 x4 x1

Supporto audio High-Definition (HD)

Ciascun connettore supporta 1 unità SATA

Ciascun connettore supporta 2 unità IDE

Connettore pannello frontale

Connettore audio frontale x1 x1

Supporta i servizi del pannello frontale

Supporta la funzione audio pannello frontale

Collettore ventolina CPU x1 Alimentazione ventolina CPU (con funzione Smart Fan)

36

Collettore ventolina sistema

Collettore cancellazione CMOS

Connettore USB

A780L3C

SPECIFICA x1 Alimentazione ventolina di sistema x1 x2

Ciascun connettore supporta 2 porte USB pannello frontale

Sistemi operativi supportati

Connettore alimentazione

(24 pin)

Connettore alimentazione

(4 pin)

Windows XP / Vista / 7 / 8 x1 x1

Connettore Porta stampante

Tastiera PS/2 x1 x1

Mouse PS/2

I/O pannello Porta VGA posteriore

Porta LAN

Porta USB x1 x1 x1 x4

Connettore audio x3

Dimensioni

182 mm (larghezza) x 225 mm (altezza) scheda

Caratteristic

Supporto RAID 0 / 1 / 10 he speciali

Ciascun connettore supporta 1 Porta stampante

Biostar si riserva il diritto di aggiungere o rimuovere il supporto di qualsiasi sistema operativo senza preavviso.

37

Motherboard Manual

Spanish

CPU

Athlon II (Vatio máximo: 95W)

Especificación

Conector AM3

Procesadores AMD Sempron / Phenom II /

La arquitectura AMD 64 permite el procesado de 32 y 64 bits

Soporta las tecnologías Hyper Transport 2.0

FSB

Admite HyperTransport 3.0 con un ancho de banda de hasta 3.2 GT/s

Conjunto de AMD 760G chips

AMD SB710

Súper E/S

Interfaz de cuenta Low Pin

ITE 8728F-BX

Le ofrece las funcionalidades heredadas de uso

Monitor hardware más común Súper E/S.

Iniciativas de control de entorno,

Función "Guardia inteligente" de ITE

Memoria principal

Gráficos

SATA

Red Local Realtek RTL 8105T

Soporte de sonido HD

Ranuras DIMM DDR3 x 2

Capacidad máxima de memoria de 16GB

Cada DIMM admite DDR de

Módulo de memoria DDR3 de canal Doble

Admite DDR3 de 800/1066/1333/1600(OC)

No admite DIMM registrados o DIMM compatibles con ECC

512MB/1GB/2GB/4GB/8GB

Integrados en el conjunto de chips AMD 760G Memoria máxima de vídeo compartida de 1024 MB

Controlador ATA Serie Integrado

Tasas de transferencia de hasta 3 Gb/s.

Compatible con la versión SATA 2.0.

VT1708B / ALC662

Negociación de 10 / 100 Mb/s

Salida de sonido de 5.1 canales

Ranuras

Ranura PCI Express X16

Ranura PCI

Conectores en placa

Conector SATA

Conector IDE

X1

X1

Soporte de sonido Alta Definición

X4

X1

Cada conector soporta 1 dispositivos SATA

Cada conector soporta 2 dispositivos IDE

Conector de panel frontal

Conector de sonido frontal

X1 Soporta instalaciones en el panel frontal

X1 Soporta funciones de sonido en el panel frontal

38

Cabecera de ventilador de CPU

Cabecera de ventilador de sistema

Cabecera de borrado de CMOS

Conector USB

Conector de alimentación

(24 patillas)

Conector de alimentación

(4 patillas)

Conector Puerto de impresora

Teclado PS/2

Ratón PS/2

Panel trasero Puerto VGA de E/S

Puerto de red local

Puerto USB

Conector de sonido

Tamaño de la placa

Funciones especiales

Soporte de sistema operativo

182 mm. (A) X 225 Mm. (H)

Admite RAID 0 / 1 / 10

Windows XP / Vista / 7 / 8

A780L3C

Especificación

X1 Fuente de alimentación de ventilador de CPU (con función

Smart Fan)

X1 Fuente de alimentación de ventilador de sistema

X1

X2 Cada conector soporta 2 puertos USB frontales

X1

X1

X1 Cada conector soporta 1 Puerto de impresora

X1

X1

X1

X1

X4

X3

Biostar se reserva el derecho de añadir o retirar el soporte de cualquier SO con o sin aviso previo.

39

Motherboard Manual

Portuguese

CPU

ESPECIFICAÇÕES

Socket AM3

Processadores AMD Sempron / Phenom II /

Athlon II (Watt máximo: 95W)

A arquitectura AMD 64 permite uma computação de 32 e 64 bits

Suporta as tecnologias Hyper Transport 2.0

FSB

Chipset

Suporta a tecnologia HyperTransport 2.0 com uma largura de banda até 3.2 GT/s

AMD 760G

AMD SB710

Especificaçã o Super I/O

Interface LPC (Low Pin Count).

ITE 8728F-BX

Proporciona as funcionalidades mais utilizadas

Iniciativas para controlo do ambiente

Monitorização do hardware em termos da especificação Super I/O.

Função "Smart Guardian" da ITE

Memória principal

Ranhuras DIMM DDR3 x 2

Capacidade máxima de memória: 16GB

Cada módulo DIMM suporta uma memória

DDR3 de 512MB/1GB/

2GB/4GB/8GB

Placa gráfica Integrada no chipset AMD 760G

Módulo de memória DDR3 de canal duplo

Suporta módulos DDR3 800/1066/1333/1600(OC)

Os módulos DIMM registados e os DIMM ECC não são suportados

SATA Controlador Serial ATA integrado

Memória de vídeo máxima partilhada: 1024 MB

Velocidades de transmissão de dados até 3 Gb/s.

Compatibilidade com a especificação SATA versão 2.0.

Auto negociação de 10 / 100 Mb/s LAN Realtek RTL 8105T

Suporte para

áudio de alta VT1708B / ALC662 definição

Ranhura PCI Express X16

Ranhuras

Ranhura PCI

Conectores na placa

Conector SATA

Conector IDE

Conector do painel frontal

Conector de áudio frontal

40 x1 x1 x4 x1 x1 x1

Saída de áudio de 5.1 canais

Suporta a especificação High-Definition Audio

Cada conector suporta 1 dispositivo SATA

Cada conector suporta 2 dispositivos IDE

Para suporte de várias funções no painel frontal

Suporta a função de áudio no painel frontal

Conector da ventoinha da CPU

Conector da ventoinha do sistema

A780L3C

ESPECIFICAÇÕES x1 Alimentação da ventoinha da CPU (com a função Smart Fan) x1 Alimentação da ventoinha do sistema

Conector para limpeza do CMOS x1 x2 x1

Cada conector suporta 2 portas USB no painel frontal Conector USB

Conector de alimentação

(24 pinos)

Conector de alimentação

(4 pinos)

Conector da para impressora

Teclado PS/2

Rato PS/2

Entradas/Saí das no painel

Porta VGA traseiro

Porta LAN

Porta USB

Tomada de áudio

Tamanho da placa

182 mm (L) X 225 mm (A)

Característic as especiais

Suporta as funções RAID 0 / 1 / 10

Sistemas operativos suportados

Windows XP / Vista / 7 / 8 x1 x1 x1 x1 x1 x1 x4 x3

Cada conector suporta 1 Porta para impressora

A Biostar reserva-se o direito de adicionar ou remover suporte para qualquer sistema operativo com ou sem aviso prévio.

41

Motherboard Manual

Polish

Procesor

SPEC

Socket AM3

AMD Sempron / Phenom II / Athlon II Procesory

Architektura AMD 64 umożliwia przetwarzanie 32 i 64 bitowe

Obsługa Hyper Transport 2.0

(Maksymalny Watt: 95W)

FSB

Chipset

Pamięć główna

Obsługa HyperTransport 3.0 o szerokości pasma do 3.2 GT/s

AMD 760G

AMD SB710

Gniazda DDR3 DIMM x 2

Maks. wielkość pamięci 16GB

Każde gniazdo DIMM obsługuje moduły

512MB/1GB/2GB/4GB/8GB DDR3

Moduł pamięci DDR3 z trybem podwójnego kanału

Obsługa DDR3 800/1066/1333/1600(OC)

Brak obsługi Registered DIMM oraz ECC DIMM

Super I/O

Grafika

SATA

LAN

Obsługa audio HD

ITE 8728F-BX

Zapewnia najbardziej powszechne funkcje

Super I/O.

Zintegrowana w chipsecie AMD 760G

Zintegrowany kontroler Serial ATA

Realtek RTL 8105T

VT1708B / ALC662

Gniazdo PCI Express X16

Gniazda

Gniazdo PCI

Złącza

Złącze SATA wbudowane

Złącze IDE

Złącze panela przedniego

Przednie złącze audio

Złącze główkowe wentylatora procesora x1 x1 x1 x4 x1 x1 x1

Interfejs Low Pin Count

Funkcje kontroli warunków pracy,

Monitor H/W

Funkcja ITE "Smart Guardian"

Maks. wielkość współdzielonej pamięci video wynosi 1024 MB

Transfer danych do 3 Gb/s.

Zgodność ze specyfikacją SATA w wersji 2.0.

10 / 100 Mb/s z automatyczną negocjacją szybkości

5.1 kanałowe wyjście audio

Obsługa High-Definition Audio

Każde złącze obsługuje 1 urządzenie SATA

Każde złącze obsługuje 2 urządzenia IDE

Obsługa elementów panela przedniego

Obsługa funkcji audio na panelu przednim

Zasilanie wentylatora procesora (z funkcją Smart Fan)

42

A780L3C

SPEC

Złącze główkowe wentylatora systemowego x1 Zasilanie wentylatora systemowego

Złącze główkowe kasowania CMOS

Złącze USB

Złącze zasilania (24 pinowe)

Złącze zasilania (4 pinowe)

Złącze Port drukarki x1 x2 x1 x1 x1

Każde złącze obsługuje 2 porty USB na panelu przednim

Każde złącze obsługuje 1 Port drukarki

Klawiatura PS/2

Mysz PS/2

Back Panel

I/O

Port VGA

Port LAN

Port USB

Gniazdo audio

Wymiary płyty

Funkcje specjalne

182 mm (S) X 225 mm (W)

Obsługa RAID 0 / 1 / 10

Obsluga systemu operacyjneg o

Windows XP / Vista / 7 / 8 x1 x1 x1 x1 x4 x3

Biostar zastrzega sobie prawo dodawania lub odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia.

43

Motherboard Manual

Russian

СПЕЦ

CPU

(центральн ый процессор)

Гнездо AM3

Процессоры AMD Sempron / Phenom II /

Athlon II (Максимальный ватт: 95W)

FSB

Поддержка HyperTransport 3.0 с пропускной способностью до 3.2 GT/s

Архитектура AMD 64 разрешать обработка данных на 32 и

64 бит

Поддержка Hyper Transport 2.0

Набор микросхем

AMD 760G

AMD SB710

Слоты DDR3 DIMM x 2

Основная память

Super I/O

Максимальная ёмкость памяти 16ГБ

Каждый модуль DIMM поддерживает

512МБ/1ГБ/2ГБ/4ГБ/8ГБ DDR3

ITE 8728F-BX

Обеспечивает наиболее используемые действующие функциональные возможности Super I/O.

Графика Встроенная в набор микросхем AMD 760G

Модуль памяти с двухканальным режимом DDR3

Поддержка DDR3 800/1066/1333/1600(OC)

Не поддерживает зарегистрированные модули DIMM and

ECC DIMM

Интерфейс с низким количеством выводов

Инициативы по охране окружающей среды,

Аппаратный монитор

Функция ITE "Smart Guardian" (Интеллектуальная защита)

Максимальная совместно используемая видео память составляет 1024 МБ

SATA

Встроенное последовательное устройство управления ATA

Локальная сеть

Звуковая поддержка жесткого диска

Realtek RTL 8105T

VT1708B / ALC662

Слот PCI Express X16

Слоты

Слот PCI

Встроенный

Разъём SATA разъём

Разъём IDE x1 x1 x4 x1 скорость передачи данных до 3 гигабит/с.

Соответствие спецификации SATA версия 2.0.

Автоматическое согласование 10 / 100 Мб/с

Звуковая поддержка High-Definition

5.1канальный звуковой выход

Каждый разъём поддерживает 1 устройство SATA

Каждый разъём поддерживает 2 встроенных интерфейса накопителей

44

A780L3C

СПЕЦ

Контактирующее приспособление

Источник питания для вентилятора центрального вентилятора центрального процессора (с функцией интеллектуального вентилятора) процессора x1

Контактирующее приспособление

Источник питания для вентилятора системы вентилятора системы x1

Открытое контактирующее приспособление CMOS x1

Каждый разъём поддерживает 2 USB-порта на лицевой

USB-разъём x2 панели

Разъем питания (24 вывод) x1

Разъем питания (4 вывод) x1

Разъём Порт подключения Каждый разъём поддерживает 1 Порт подключения

Задняя панель средств ввода-выво да

Клавиатура PS/2

Мышь PS/2

Порт VGA

Порт LAN x1 x1 x1 x1

USB-порт x4

Гнездо для подключения наушников x3

Размер панели

Специальн ые

182 мм (Ш) X 225 мм (В) технические характерист

Поддержка RAID 0 / 1 / 10 ики

Поддержка

OS

Windows XP / Vista / 7 / 8

Biostar сохраняет за собой право добавлять или удалять средства обеспечения для OS с или без предварительного уведомления.

45

Motherboard Manual

Arabic

ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﺖﺑ 64 و 32 ﺔﻋﺮﺴﺑ ﺔﻴﺑﻮﺳﺎﺤﻟا تﺎﻴﻠﻤﻌﻟا ءاﺮﺟإ

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗHyper Transport 2.0

و

تﺎﻔﺻاﻮﻤﻟا

ﺲﺒﻘﻣAM3

تﺎﺠﻟﺎﻌﻣAMD Sempron / Phenom II / Athlon II

(طاو ىﻮﺼﻗ: 95و)

ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو

ﺔﻳﺰآﺮﻤﻟا

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗHyperTransport 3.0

ﻰﻟإ ﻞﺼﻳ ددﺮﺘﺑ 3.2 GT/s ﻲﺒﻧﺎﺠﻟا ﻲﻣﺎﻣﻷا ﻞﻗﺎﻨﻟا

AMD 760G

AMD SB710

ﺢﺋاﺮﺸﻟا ﺔﻋﻮﻤﺠﻣ

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ Low Pin Count Interface

: ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو

ةﺰﻬﺟﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻣ

ﺔﻔﻴﻇو"Smart Guardian" ﻦﻣ ITE

ةﺮآاذ ةﺪﺣوDDR3 ةﺎﻨﻘﻟا ﺔﺟودﺰﻣ

ITE 8728F-BX

ﺔﻔﻴﻇو ﺮﻓﻮﺗSuper I/O ًﺎﻣاﺪﺨﺘﺳا ﺮﺜآﻷا

عﻮﻧ ﻦﻣ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR3 ( OC ) 1600 / 1333 / 1066 / 800 تﺎﻌﺳ ﺖﻳﺎﺑ ﺎﺠﻴﺟ 16 ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ

ﺖﻳﺎﺑ ﺎﺠﻴﻣ ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻧ ﻦﻣ ةﺮآاذ ﻢﻋﺪﺗ DDR3 ﺔﻌﺳ /512 ﺖﻳﺎﺑ ﺎﺠﻴﻣ

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻣ ﻖ ﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ECC

2 دﺪﻋ DDR3 DIMM ﺔﺤﺘﻓ

ﺖﻳﺎﺑ ﺎﺠﻴﻣ 1024 ﺔآﺮﺘﺸﻤﻟا ﻮﻳﺪﻴﻔﻟا ةﺮآاﺬﻟ ﺔﻌﺳ ﻰﺼﻗأ

Super I/O

ﺔﻴﺴﻴﺋﺮﻟا ةﺮآاﺬﻟا

ﺖﻳﺎﺑ ﺎﺠﻴﺟ 8 و / 4 و / 2 و / 1 و

ﻖﺋﺎﻗر ﻲﻓ ﺔﺠﻣﺪﻣ AMD 760G تﺎﻣﻮﺳﺮﻟا ﺔﻗﺎﻄﺑ

ﻰﻟإ ﻞﺼﺗ تﺎﻋﺮﺴﺑ تﺎﻧﺎﻴﺒ ﻟا ﻞﻘﻧ 3 .

ﺔﻴﻧﺎﺛ / ﺖﺑﺎﺠﻴﺟ

تﺎﻔﺻاﻮﻤﻟ ﺔﻘﺑﺎﻄﻣSATA راﺪﺻﻹا 2.0.

ﺔﻴﻧﺎﺛ / ﺖﻳﺎﺑ ﺎﺠﻴﻣ 100 / 10 ﻲﺋﺎﻘﻠﺗ ضوﺎﻔﺗ

5.1تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ

ﻦﻣ ﻒﻳﺮﻌﺘﻟا ﻲﻟﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ

ةﺰﻬﺟأ ﻦﻣ ﺪﺣاو ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪﻳSATA

ةﺰﻬﺟأ ﻦﻣ ﻦﻴﻨﺛا ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪﻳIDE

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪﻳ

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠ ﻟﺎﺑ تﻮﺼﻟا ﺔﻔﻴﻇو ﻢﻋﺪﻳ

1 دﺪﻋ

1 دﺪﻋ

4 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

ﻢﻜﺤﺘﻣSerial ATAﻞﻣﺎﻜﺘﻣ

Realtek RTL 8105T ﺔﻴﻠﺧاد ﺔﻜﺒﺷ

VT1708B / ALC662

ﻲﻟﺎﻋ تﻮﺼﻟا ﻢﻋد

ﻒ ﻳﺮﻌﺘﻟا

PCI Express x16 ﺔﺤﺘﻓ

PCI ﺔﺤﺘﻓ

SATA ﺬﻔﻨﻣ

IDE ﺬﻔﻨﻣ

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻣ

ﻲﻣﺎﻣﻷا تﻮﺼﻟا ﺬﻔﻨﻣ

SATA

تﺎﺤﺘﻔﻟا

ﺢﻄﺳ ﻰﻠﻋ ﺬﻓﺎﻨﻤﻟا

ﺔﺣﻮﻠﻟا

46

ﺔﻔﻴﻇو ﻊﻣ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺘﻟSmart Fan

مﺎﻈﻨﻟا ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺘﻟ

ﻲﺘﺤﺘﻓ ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪﻳUSBﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟﺎﺑ

تﺎﻔﺻاﻮﻤﻟا

1 دﺪﻋ ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻣ ﺔﻠﺻو

1 دﺪﻋ مﺎﻈﻨﻟا ﺔﺣوﺮﻣ ﺔﻠﺻو

1

2

دﺪﻋ

دﺪﻋ

CMOS ﺢﺴﻣ ﺔﻠﺻو

USB ﺬﻔ ﻨﻣ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

4 دﺪﻋ

3 ﺪﻋ

( سﻮﺑد 24 ) ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ ﺬﻔﻨﻣ

( سﻮﺑد 4 ) ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ ﺬﻔﻨﻣ

ﺔﻌﺑﺎﻃ ﺬﻔﻨﻣ

PS/2 ﺢﻴﺗﺎﻔﻣ ﺔﺣﻮﻟ

PS/2 سوﺎﻣ

VGA ﺬﻔﻨﻣ

ﺔﻴﻠﺤﻣ لﺎﺼﺗا ﺔﻜﺒﺷ ﺬﻔﻨﻣ

USB ﺬﻓﺎﻨﻣ

تﻮﺻ ﺲﺒﻘﻣ

A780L3C

جﺮﺧ / ﻞﺧد ﺬﻓﺎﻨﻣ

ﺔﻴﻔﻠﺨﻟا ﺔﺣﻮﻠﻟا

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗRAID 0 / 1 / 10

ﺔﺣﻮﻠﻟا ﻢﺠﺣ

ﺔﺻﺎﺧ ﺎﻳاﺰﻣ

ﻆﻔﺘﺤﺗBiostar وأ رﺎﻄﺧﺈﺑ ﻞﻴﻐﺸﺗ مﺎﻈﻧ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺑ

.

رﺎﻄﺧإ نوﺪﺑ

Windows XP / Vista / 7 / 8 ﻞﻴﻐﺸﺘﻟا ﺔﻤﻈﻧأ ﻢﻋد

47

Motherboard Manual

Japanese

仕様

CPU

FSB

Socket AM3

AMD Sempron / Phenom II / Athlon II プロセッ

です

ハイパートランスポート 2.0とクールアンドクワイアットをサ

サ (最高のワット: 95W)

AMD 64アーキテクチャでは、32ビットと64ビット計算が可能

ポートします

3.2 GT/sのバンド幅までハイパートランスポー

ト 3.0をサポートします

チップセッ

ト

AMD 760G

AMD SB710

メインメモ

リ

DDR3 DIMMスロット x 2

最大メモリ容量 16GB

各 DIMMは 512MB/1GB/2GB/4GB/8GB DDR3

DDR3 800/1066/1333/1600(OC) をサポート

登録済み DIMMとECC DIMMはサポートされません

をサポート

デュアル チャンネルモードDDR3メモリモジュール

Super I/O

ITE 8728F-BX

もっとも一般に使用されるレガシー Super I/O

機能を採用しています。

低ピンカウントインターフェイス

環境コントロールイニシアチブ、

H/Wモニター

ITEの「スマートガーディアン」機能

グラフィッ

クス

AMD 760Gチップセットに統合 最大の共有ビデオメモリは 1024MBです

SATA

統合シリアル ATAコントローラ

最高 3Gb/秒のデータ転送速度

SATAバージョン2.0仕様に準拠。

10 / 100 Mb/秒のオートネゴシエーション LAN Realtek RTL 8105T

HDオーディ

オのサポー

ト

VT1708B / ALC662

スロット

5.1チャンネルオーディオアウト

ハイデフィニションオーディオのサポート

PCI Express X16スロット x1

PCIスロット x1

オンボード

コネクタ

フロントパネルコネクタ x1

48

A780L3C

仕様

フロントオーディオコネクタ x1

システムファンヘッダ x1

CMOSクリアヘッダ x1

各コネクタは 2つのフロントパネルUSBポートをサポートし

USBコネクタ x2

ます

電源コネクタ (24ピン)

電源コネクタ (4ピン) x1 x1

プリンタポートコネクタ x1 1つのプリンタポートをサポートします

PS/2キーボード

PS/2マウス x1 x1

背面パネル

I/O

VGAポート x1

LANポート x1

USBポート x4

オーディオジャック x3

ボードサイ

ズ

特殊機能

182 mm (幅) X 225 mm (高さ)

RAID 0 / 1 / 10 のサポート

Biostarは事前のサポートなしにOSサポートを追加または削

OSサポート Windows XP / Vista / 7 / 8

除する権利を留保します。

2013/04/01

49