Biostar Hi-Fi A55S3 Owner's Manual

Biostar Hi-Fi A55S3 Owner's Manual
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3 Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee that
interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the contents
here and specially disclaims any implied warranties of merchantability or fitness
for any purpose. Further the vendor reserves the right to revise this publication
and to make changes to the contents here without obligation to notify any party
beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and we
will not be responsible for any mistakes found in this user’s manual. All the brand
and product names are trademarks of their respective companies.
Dichiarazione di conformità
sintetica
Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002
Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive
2004/108/CE, 2006/95/CE e
1999/05/CE
quando ad esso applicabili
Short Declaration of conformity
We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives
2004/108/CE, 2006/95/CE and
1999/05/CE
whenever these laws may be applied
Table of Contents
Chapter 1: Introduction ...............................................................1
1.1
1.2
1.3
1.4
1.5
Before You Start......................................................................... 1
Package Checklist ..................................................................... 1
Motherboard Specifications ....................................................... 2
Rear Panel Connectors ............................................................. 4
Motherboard Layout .................................................................. 5
Chapter 2: Hardware Installation ................................................7
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Install Central Processing Unit (CPU) ....................................... 7
Install a Heatsink ....................................................................... 8
Connect Cooling Fans ............................................................... 9
Install System Memory ............................................................ 10
Expansion Slots ....................................................................... 12
Jumper Setting ........................................................................ 13
Headers & Connectors ............................................................ 14
Chapter 3: UEFI BIOS & Software.............................................19
3.1
3.2
3.3
UEFI BIOS Setup .................................................................... 19
BIOS Update ........................................................................... 19
Software................................................................................... 24
Chapter 4: Useful Help ..............................................................27
4.1
4.2
4.3
4.4
4.5
Driver Installation..................................................................... 27
AMI BIOS Beep Code.............................................................. 28
Troubleshooting ....................................................................... 28
RAID Functions ....................................................................... 30
AMD Dual Graphics Technology ............................................. 34
Appendix: Specifications In Other Languages .......................36
Arabic ......................................................................................................... 36
French ........................................................................................................ 38
German....................................................................................................... 40
Italian .......................................................................................................... 42
Japanese .................................................................................................... 44
Polish.......................................................................................................... 46
Portuguese ................................................................................................. 48
Russian....................................................................................................... 50
Spanish....................................................................................................... 52
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
CHAPTER 1: INTRODUCTION
1.1
Before You Start
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
„ Prepare a dry and stable working environment with
sufficient lighting.
„ Always disconnect the computer from power outlet before
operation.
„ Before you take the motherboard out from anti-static bag,
ground yourself properly by touching any safely grounded
appliance, or use grounded wrist strap to remove the static
charge.
„ Avoid touching the components on motherboard or the rear
side of the board unless necessary. Hold the board on the
edge, do not try to bend or flex the board.
„ Do not leave any unfastened small parts inside the case
after installation. Loose parts will cause short circuits which
may damage the equipment.
„ Keep the computer from dangerous area, such as heat
source, humid air and water.
„ The operating temperatures of the computer should be 0 to
45 degrees Celsius.
„ To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit
1.2
Package Checklist
;
;
;
;
Serial ATA Cable x2
Rear I/O Panel for ATX Case x1
Installation Guide x1
Fully Setup Driver DVD x1
Note: The package contents may be different due to the sales region or models in which it was
sold. For more information about the standard package in your region, please contact your dealer
or sales representative.
1
Motherboard Manual
1.3
Motherboard Specifications
Specifications
Socket FM2 for AMD A-series processor
CPU Support
Maximum CPU TDP (Thermal Design Power): 100Watt
* Please refer to www.biostar.com.tw for CPU support list.
AMD A85 FCH (Hi-Fi A85S3)
Chipset
AMD A75 FCH (Hi-Fi A75S3)
AMD A55 FCH (Hi-Fi A55S3)
Supports Dual Channel DDR3 800/ 1066/ 1333/ 1600/ 1866
Memory
2 x DDR3 DIMM Memory Slot, Max. Supports up to 32 GB Memory
Each DIMM supports non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3 module
* Please refer to www.biostar.com.tw for Memory support list.
AMD A85/A75/A55 FCH
Storage
Supports RAID 0,1,10, 5 & AHCI (AMD A85 FCH)
Supports RAID 0,1,10, & AHCI (AMD A75/A55 FCH),
LAN
Audio Codec
Realtek RTL 8111F
10/ 100/ 1000 Mb/s auto negotiation, Half / Full duplex capability
ALC662
5.1 Channels, High Definition Audio, Biostar Hi-Fi
AMD A85/A75 FCH:
6x USB 2.0 port (2 on rear I/Os and 4 via internal headers)
USB
4x USB 3.0 port (2 on rear I/Os and 2 via internal headers)
AMD A55 FCH:
8x USB 2.0 port (4 on rear I/Os and 4 via internal headers)
1x PCI Slot
Expansion Slots
1x PCIe 2.0 x1 Slot
1x PCIe 2.0 x16 Slot
Rear I/Os
2
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
1x PS/2 Mouse
1x PS/2 Mouse
1x PS/2 Mouse
1x PS/2 Keyboard
1x PS/2 Keyboard
1x PS/2 Keyboard
1x VGA Port
1x VGA Port
1x VGA Port
1x HDMI Port
1x DVI Port
1x DVI Port
1x LAN port
1x LAN port
1x LAN port
2x USB 2.0 Port
2x USB 2.0 Port
4x USB 2.0 Port
2x USB 3.0 Port
2x USB 3.0 Port
3x Audio Jack
3x Audio Jack
3x Audio Jack
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
Specifications
Internal I/Os
Form Factor
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
6x SATA 6.0Gb/s Connector
6x SATA 6.0Gb/s Connector
6x SATA 3.0Gb/s Connector
2x USB 2.0 Header
2x USB 2.0 Header
2x USB 2.0 Header
1x USB 3.0 Header
1x USB 3.0 Header
1x 4-Pin Power Connector
1x 4-Pin Power Connector
1x 4-Pin Power Connector
1x 24-Pin Power Connector
1x 24-Pin Power Connector
1x 24-Pin Power Connector
1x CPU Fan Connector
1x CPU Fan Connector
1x CPU Fan Connector
1x System Fan Connector
1x System Fan Connector
1x System Fan Connector
1x Front Panel Header
1x Front Panel Header
1x Front Panel Header
1x Front Audio Header
1x Front Audio Header
1x Front Audio Header
1x Clear CMOS Header
1x Clear CMOS Header
1x Clear CMOS Header
1x Printer Port Header
1x Printer Port Header
1x Printer Port Header
1x Serial Port Header
1x Serial Port Header
1x Serial Port Header
microATX Form Factor, 244 mm x 191 mm
Windows XP / Vista / 7/ 8
OS Support
Biostar reserves the right to add or remove support for any OS with or without
notice.
3
Motherboard Manual
1.4
Rear Panel Connectors
Hi-Fi A85S3
Hi-Fi A75S3
Hi-Fi A55S3
Note 1:
Note 2:
Note 3:
Note 4:
HDMI / DVI-D / VGA Output require an AMD family processor with intedrated graphics.
The mainboard supports two independent display outputs.
Since the audio chip supports High Definition Audio Specification, the function of each
audio jack can be defined by software. The input / output function of each audio jack
listed above represents the default setting. However, when connecting external
microphone to the audio port, please use the Line In (Blue) and Mic In (Pink) audio jack.
Maximum resolution:
Outputs
HDMI
DVI-D
VGA
4
Maximum resolution
1920 x 1080 @60Hz
1920 x 1200 @60Hz
1920 x 1200 @60Hz
2560 x 1600 @60Hz
1920 x 1600 @60Hz
Bit Depth
24, 30, 36 bpp
24 bpp
30 bpp
24 bpp
--
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
1.5
Motherboard Layout
Hi-Fi A85S3
5
Motherboard Manual
Hi-Fi A75S3/Hi-Fi A55S3
Note1: ■ represents the 1st pin.
Note2: HDMI connector is for Hi-Fi A85S3. DVI connector is for Hi-Fi A75S3 & Hi-Fi A55S3.
Note3: The USB 3.0 header is only for Hi-Fi A85S3 and Hi-Fi A75S3
6
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
CHAPTER 2: HARDWARE INSTALLATION
2.1
Install Central Processing Unit (CPU)
Step 1: Locate the CPU socket on the motherboard
Step 2: Pull the socket locking out from the socket and then raise the lever up to
a 90-degree angel.
Step 3: Look for the white triangle on socket, and the gold triangle on CPU
should point towards this white triangle. The CPU will fit only in the
correct orientation.
Note: The CPU fits only in one correct orientation. Do not force the CPU into the socket to
prevent damaging the CPU.
7
Motherboard Manual
Step 4: Hold the CPU down firmly, and then close the lever to locked the position
2.2
Install a Heatsink
Step 1: Place the heatsink and fan assembly onto the retention frame. Match the
heatsink clip with the socket mounting-lug. Hook the spring clip to the
mounting-lug.
Step 2: On the other side, push the retention clip straight down to lock into the
plastic lug on the retention frame, and then press down the locker until it
stops.
Note1: Do not forget to connect the CPU fan connector.
Note2: For proper installation, please kindly refer to the installation manual of your CPU
heatsink.
8
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
2.3
Connect Cooling Fans
These fan headers support cooling-fans built in the computer. The fan cable and
connector may be different according to the fan manufacturer. Connect the fan
cable to the connector while matching the black wire to pin#1.
CPU_FAN1: CPU Fan Header
Pin
1
2
3
Assignment
Ground
+12V
FAN RPM rate sense
4
Smart Fan Control
(By Fan)
Pin
1
2
3
Assignment
Ground
+12V
SYS_FAN1: System Fan Header
FAN RPM rate sense
Note: CPU_FAN1, SYS_FAN1 support 4-pin and 3-pin head connectors. When connecting
with wires onto connectors, please note that the red wire is the positive and should be
connected to pin#2, and the black wire is Ground and should be connected to GND.
9
Motherboard Manual
2.4
Install System Memory
A. DDR3 Modules
Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM
on the slot such that the notch on the DIMM matches the break on the slot.
Step 2: Insert the DIMM vertically and firmly into the slot until the retaining chip
snap back in place and the DIMM is properly seated.
Note: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.
10
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
B. Memory Capacity
DIMM Socket Location
DDR3 Module
DDR3_A1
512MB/1GB/2GB/4GB/8GB/16GB
DDR3_B1
512MB/1GB/2GB/4GB/8GB/16GB
Total Memory Size
Max is 32GB.
C. Dual Channel Memory Installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status
DDR3_A1
DDR3_B1
Disabled
O
X
Disabled
X
O
Enabled
O
O
(O means memory installed, X means memory not installed.)
Note: The DRAM bus width of the memory module must be the same (x8 or x16)
11
Motherboard Manual
2.5
Expansion Slots
PEX16_1: PCI-Express Gen2 x16 Slot
-
PCI-Express 2.0 compliant.
Maximum theoretical realized bandwidth of 8GB/s simultaneously per
direction, for an aggregate of 16GB/s totally.
PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.
PEX1_1: PCI-Express Gen2 x1 Slot
-
PCI-Express 2.0 compliant.
Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total
PCI1: Peripheral Component Interconnect Slot
This motherboard is equipped with 1 standard PCI slot. PCI stands for Peripheral
Component Interconnect, and it is a bus standard for expansion cards.
Install an Expansion Card
You can install your expansion card by following steps:
1.
Read the related expansion card's instruction document before install the
expansion card into the computer.
2.
Remove your computer's chassis cover, screws and slot bracket from the
computer.
3.
Place a card in the expansion slot and press down on the card until it is
completely seated in the slot.
4.
Secure the card’s metal bracket to the chassis back panel with a screw.
5.
Replace your computer's chassis cover.
6.
Power on the computer, if necessary, change BIOS settings for the
expansion card.
7.
Install related driver for the expansion card.
12
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
2.6
Jumper Setting
The illustration shows how to set up jumpers. When the jumper cap is placed on
pins, the jumper is “close”, if not, that means the jumper is “open”.
Pin opened
Pin closed
Pin1-2 closed
JCMOS1: Clear CMOS Header
Placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.
1
3
Pin 1-2 Close:
Normal Operation (default).
1
3
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1.
2.
3.
4.
5.
6.
Remove AC power line.
Set the jumper to “Pin 2-3 close”.
Wait for five seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
Load Optimal Defaults and save settings in CMOS.
13
Motherboard Manual
2.7
Headers & Connectors
ATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX power
supply.
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Assignment
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Assignment
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V
ATXPWR2: ATX Power Source Connector
This connector will provide +12V to CPU power circuit.
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
Note1: Before you power on the system, please make sure that both ATXPWR1 and
ATXPWR2 connectors have been plugged-in.
Note2: Insufficient power supplied to the system may result in instability or the
peripherals not functioning properly. Use of a PSU with a higher power output is
recommended when configuring a system with more power-consuming devices.
14
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
PANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.
Pin
1
2
3
4
5
6
7
8
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Function
Speaker
Connector
Hard drive LED
Reset button
Pin
9
10
11
12
13
14
15
16
Assignment
N/A
N/A
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Function
N/A
N/A
Power LED
Power-on button
SATA1~SATA6: Serial ATA Connectors
These connectors connect to SATA hard disk drives via SATA cables.
„ Hi-Fi A85S3 & Hi-Fi A75S3 satisfy the SATA 3.0 spec and with transfer rate of 6.0Gb/s.
„ Hi-Fi A55S3 satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.
Pin
1
2
3
4
5
6
7
Assignment
Ground
TX+
TXGround
RXRX+
Ground
15
Motherboard Manual
JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with a wide range of simultaneously accessible
external Plug and Play peripherals.
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
VBUS0
SSRX1SSRX1+
Ground
SSTX1SSTX1+
Ground
D1D1+
ID
Pin
11
12
13
14
15
16
17
18
19
20
Assignment
D2+
D2Ground
SSTX2+
SSTX2Ground
SSRX2+
SSRX2VBUS1
Key
Note: The USB 3.0 header is only for Hi-Fi A85S3 and Hi-Fi A75S3
F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with a wide range of simultaneously accessible
external Plug and Play peripherals.
Pin
1
2
3
4
5
6
7
8
9
10
16
Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
NC
Key
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
F_AUDIO1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header supports HD and AC’97 audio front panel connector.
Pin
1
2
3
4
5
6
7
8
9
10
HD Audio
Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense
Pin
1
2
3
4
5
6
7
8
9
10
AC’97
Assignment
Mic In
Ground
Mic Power
Audio Power
RT Line Out
RT Line Out
Reserved
Key
LFT Line Out
LFT Line Out
Note1: It is recommended that you connect a high-definition front panel audio module
to this connector to avail of the motherboard's high definition audio capability.
Note2: Please try to disable the "Front Panel Jack Detection" if you want to use an
AC'97 front audio output cable. The function can be found via O.S. Audio Utility.
J_COM1: Serial Port Connector
The motherboard has a Serial Port Connector for connecting RS-232 Port.
Pin
Assignment
1
2
3
4
5
6
7
8
9
10
Carrier detect
Received data
Transmitted data
Data terminal ready
Signal ground
Data set ready
Request to send
Clear to send
Ring indicator
NC
17
Motherboard Manual
J_PRINT1: Printer Port Connector
This header allows you to connector printer on the PC.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
18
Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5
Pin
14
15
16
17
18
19
20
21
22
23
24
25
26
Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
CHAPTER 3: UEFI BIOS & SOFTWARE
3.1
„
„
3.2
UEFI BIOS Setup
For better system performance, the UEFI BIOS firmware is being
continuously updated. The UEFI BIOS information described below in this
manual is for your reference only and the actual UEFI BIOS information
and settings on board may be different from this manual
For further information of setting up the UEFI BIOS, please refer to the
UEFI BIOS Manual in the Setup DVD.
BIOS Update
There are three ways to update the BIOS:
BIOS Update Utility, BIOS Online Update Utility and BIOS Flasher.
1. BIOS Update Utility
1. Installing BIOS Update Utility from the DVD Driver.
2. Download the proper BIOS from www.biostar.com.tw .
3. Open BIOS Update Utility and
click the Update BIOS button on
the main screen.
4. A warning message will show
up to request your agreement to
start the BIOS update. Click OK to
start the update procedure.
5. Choose the location for your
BIOS file in the system. Please
select the proper BIOS file, and
then click on Open. It will take
several minutes, please be
patient.
19
Motherboard Manual
6. After the BIOS Update process is
finished, click on OK to reboot the
system.
7. While the system boots up and the full screen logo shows up, please press
the
<Delete> key to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore
Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.
Backup BIOS
Click the Backup BIOS button on the
main screen for the backup of BIOS,
and select a proper location for your
backup BIOS file in the system, and
click Save.
20
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
2. Online Update Utility
1. Installing BIOS Update Utility from the DVD Driver.
2. Please make sure the system is connected to the internet before using this
function.
3. Open BIOS Update Utility and
click the Online Update button
on the main screen.
4. An open dialog will show up to
request your agreement to
start the BIOS update. Click
Yes to start the online update
procedure.
5. If there is a new BIOS version,
the utility will ask you to
download it. Click Yes to
proceed.
6. After the download is
completed, you will be asked
to program (update) the BIOS
or not. Click Yes to proceed.
7. After the updating process is
finished, you will be asked you
to reboot the system. Click OK
to reboot.
21
Motherboard Manual
8. While the system boots up and the full screen logo shows up, press
<Delete> key to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore
Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.
3. BIOSTAR BIOS Flasher
BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and
simple way to update your BIOS via USB pen drive.
Note1: This utility only allows storage device with FAT32/16 format and single partition.
Note2: Shutting down or resetting the system while updating the BIOS will lead to system
boot failure.
The BIOSTAR BIOS Flasher is built in the BIOS ROM. To enter the utility, press
<F12> during the Power-On Self Tests (POST) procedure while booting up.
Updating BIOS with BIOSTAR BIOS Flasher
1. Go to the website to download the latest BIOS file for the motherboard.
2. Then, copy and save the BIOS file into a USB flash (pen) drive.
3. Insert the USB pen drive that contains the BIOS file to the USB port.
4. Power on or reset the computer and then press <F12> during the POST process.
5. After entering the POST
screen, the BIOS-FLASHER
utility pops out. Choose [fs0] to
search for the BIOS file.
22
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
6. Select the proper BIOS file,
and a message asking if you
are sure to flash the BIOS file.
Click Yes to start updating
BIOS.
7. A dialog pops out after BIOS
flash is completed, asking you
to restart the system. Press the
[Y] key to restart system.
8. While the system boots up and the full screen logo shows up, press
<Delete> key to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore
Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.
23
Motherboard Manual
3.3
Software
Installing Software
1. Insert the Setup DVD to the optical drive. The driver installation program would
appear if the Autorun function has been enabled.
2. Select Software Installation, and then click on the respective software title.
3. Follow the on-screen instructions to complete the installation.
Note1: All the information and content about following software are subject to be changed
without notice. For better performance, the software is being continuously updated.
Note2: The information and pictures described below are for your reference only. The actual
information and settings on board may be slightly different from this manual.
Launching Software
After the installation process is completed, you will see the software icon showing on
the desktop. Double-click the icon to launch it.
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our Tech-Support
system. This utility will collect the system information which is useful for analyzing the
problem you may have encountered, and then send these information to our
tech-support department to help you fix the problem.
Note: Before you use this utility, please set Outlook Express as your default e-mail client application
program.
represents important
information that you
must provide. Without
this information, you may
not be able to send out
the mail.
*
This block will show
the information which
would be collected in
the mail.
condition
*Describe
of your system.
your area or
*Select
the area close to you.
Provide the e-mail
address that you would
like to send the copy to.
the name of
*Provide
the memory module
manufacturer.
Provide the name of
the power supply
manufacturer and the
model no.
Send the mail out.
Exit this dialog.
Save these information to a .txt file
24
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.
If you want to save this information to a .txt file, click “Save As…” and then you will
see a saving dialog appears asking you to enter file name.
Enter the file name and then click “Save”.
Your system information will be saved to
a .txt file.
Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This information
is also concluded in the sent mail.
Note1: We will not share customer’s data with any other third parties, so please feel free to
provide your system information while using eHot-Line service.
Note2: If you are not using Outlook Express as your default e-mail client application, you may
need to save the system information to a .txt file and send the file to our tech support with other
e-mail application. Go to the following web http://www.biostar.com.tw/app/en/about/contact.php
for getting our contact information.
25
Motherboard Manual
Smart EAR
Smart EAR is a windows-based audio utility which allows you to easily
adjust system volume. With its user-friendly GUI, you can also adjust
impedance setting (Low/High Gain) to optimize your headphone
performance.
z
High/Low Gain Switch: Keep the gain switch to low for low impedance
headphone and set to high for high impedance headphone.
z
Mute Button: To disable system sound
z
Volume Control Knob: The volume can be finely adjusted by turning the
knob either clockwise or anti-clockwise to increase or decrease system
volume accordingly.
z
Information Button: Get information of the application
z
Minimize Button: Minimize the application window to the taskbar
z
Exit Button: Exit the application
Note:
1. Smart EAR is only supported by Windows 7/8 and BIOSTAR Hi-Fi series motherboards.
2. High/Low Gain Switch is only for “Front Panel Audio Header”, please make sure you are
connecting your headphone to the front panel I/O.
26
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
CHAPTER 4: USEFUL HELP
4.1
Driver Installation
After you installed your operating system, please insert the Fully Setup Driver
DVD into your optical drive and install the driver for better system performance.
You will see the following window after you insert the DVD
The setup guide will auto detect your motherboard and operating system.
Note: If this window didn’t show up after you insert the Driver DVD, please use file
browser to locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will list the
compatible driver for your motherboard and operating system. Click on each
device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide will
list the software available for your system, click on each software title to launch
the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver DVD.
Click on the Manual icon to browse for available manual.
Note: You will need Acrobat Reader to open the manual file. Please download the latest
version of Acrobat Reader software from http://get.adobe.com/reader/
27
Motherboard Manual
4.2
AMI BIOS Beep Code
Boot Block Beep Codes
Number of Beeps
Continuing
Description
Memory sizing error or Memory module not found
POST BIOS Beep Codes
Number of Beeps
1
8
4.3
Description
Success booting.
Display memory error (system video adapter)
Troubleshooting
Probable
1.
2.
Solution
There is no power in the system. 1.
Power LED does not shine; the fan
of the power supply does not work 2.
Indicator light on keyboard does 3.
not shine.
Make sure power cable is securely
plugged in.
Replace cable.
Contact technical support.
System is inoperative. Keyboard lights Using even pressure on both ends of the
are on, power indicator lights are lit,
DIMM, press down firmly until the module
and hard drives are running.
snaps into place.
System does not boot from a hard disk 1.
drive, but can be booted from optical
drive.
2.
System only boots from an optical
drive. Hard disks can be read,
applications can be used, but system
fails to boot from a hard disk.
1.
2.
Screen message shows “Invalid
Configuration” or “CMOS Failure.”
Review system’s equipment. Make sure
correct information is in setup.
System cannot boot after user installs 1.
a second hard drive.
2.
28
Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged in;
check the drive type in the standard
CMOS setup.
Backing up the hard drive is
extremely important. All hard disks
are capable of breaking down at any
time.
Back up data and applications files.
Reformat the hard drive. Re-install
applications and data using backup
disks.
Set master/slave jumpers correctly.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility with
other drives.
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
CPU Overheated
If the system shutdown automatically after power on system for seconds,
that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown automatically
to avoid a damage of the CPU, and the system may not power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
29
Motherboard Manual
4.4
RAID Functions
Operating System
Supports Windows Vista , Windows 7 and Windows 8.
Raid Arrays
RAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write
times for many applications.
RAID 1: RAID 1 defines techniques for mirroring data.
RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1.
RAID 5: RAID 5 provides fault tolerance and better utilization of disk capacity.
RAID Definitions
RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It
breaks up a large file into smaller blocks and performs disk reads and writes
across multiple drives in parallel. The size of each block is determined by the
stripe size parameter, which you set during the creation of the RAID set based
on the system environment. This technique reduces overall disk access time
and offers high bandwidth.
Features and Benefits
­
­
­
­
­
­
Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the
platform.
Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.
Benefits: provides increased data throughput, especially for large files. No
capacity loss penalty for parity.
Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.
Fault Tolerance: No.
Total Capacity: (Minimal. HDD Capacity) x (Connected HDDs Amount)
Block 1
Block 3
Block 5
30
Block 2
Block 4
Block 6
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a
RAID 1 array system. The mirrored (backup) copy of the data can reside on the
same disk or on a second redundant drive in the array. RAID 1 provides a
hot-standby copy of data if the active volume or drive is corrupted or becomes
unavailable because of a hardware failure.
RAID techniques can be applied for high-availability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive
and less reliable media.
Features and Benefits
­
­
­
­
­
Drives: Minimum 2, and maximum is 2.
Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
Fault Tolerance: Yes.
Block 1
Block 2
Block 3
Block 1
Block 2
Block 3
31
Motherboard Manual
RAID 10:
RAID 1 drives can be stripped using RAID 0 techniques.Resulting in a RAID 10
solution for improved resiliency, performance and rebuild performance.
Features and Benefits
­
­
­
­
Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID levels
in an array, and allows for spare disks.
Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
Fault Tolerance: Yes.
Block 1
Block 3
Block 5
32
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
Block 2
Block 4
Block 6
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
RAID 5:
RAID 5 stripes both data and parity information across three or more drives. It
writes data and parity blocks across all the drives in the array. Fault tolerance is
maintained by ensuring that the parity information for any given block of data is
placed on a different drive from those used to store the data itself.
Note: The RAID 5 function is only supported by A85 chipset.
Features and Benefits
­
­
­
­
­
Drives: Minimum 3.
Uses: RAID 5 is recommended for transaction processing and general
purpose service.
Benefits: An ideal combination of good performance, good fault tolerance,
and high capacity and storage efficiency.
Drawbacks: Individual block data transfer rate same as a single disk. Write
performance can be CPU intensive.
Fault Tolerance: Yes.
Disk 1
DATA 1
DATA 3
PARITY
DATA 7
DATA 9
PARITY
Disk 2
DATA 2
PARITY
DATA 5
DATA 8
PARITY
DATA 11
Disk 3
PARITY
DATA 4
DATA 6
PARITY
DATA 10
DATA 12
33
Motherboard Manual
4.5
AMD Dual Graphics Technology
AMD Dual Graphics Technology Introduction
When user adds a PCIE display adapter, it can be integrated with IGD to
show better performance. To make the two video devices work
simultaneously and normally, please refer to the following setting.
AMD Dual Graphics Requirement
„
Operating System: Windows Vista / Windows 7 / Windows 8
„
Supported Dual Graphics Combinations:
AMD Radeon™ Graphics Card
A10-Series
HD 7660D
A8-Series
HD7560D
HD 6670
●
●
HD 6570
●
●
HD 6450
A6-Series
HD 7540D
●
●
● Recommended graphics cards for AMD dual-graphics
Note 1: A4-Series products do not support Dual Graphics.
Note 2: The information described above in this manual is for your reference only and the
actual information and settings on board may be different from this manual. For further AMD
Dual Graphics information, please visit the following website: http://www.amd.com
34
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
AMD Dual Graphics Setup
Step 1: Insert Dual Graphics-Ready graphics card into PEX16_1 slot.
Step 2: Set the BIOS setting as follows:
[Chipset]→[North Bridge]→[GFX Configuration]
→[Surround View]→[Enabled]
Step 3: Install Driver DVD Chipset Driver, and reboot the system. Activate
AMD VISION Engine Control Center to make sure CrossFire has
been enabled.
35
‫‪Motherboard Manual‬‬
‫‪APPENDIX: Specifications In Other Languages‬‬
‫‪Arabic‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫ﻗﺎﻋﺪة وﺣﺪة‬
‫اﻟﻤﺄﺧﺬ ‪ FM 2‬ﻟﻤﻌﺎﻟﺞ اﻳﻪ إم دى ‪ AMD‬ﺗﺴﻠﺴﻞ ‪A‬‬
‫اﻟﻤﻌﺎﻟﺠﺔ‬
‫اﻟﺤﺪ اﻷﻗﺼﻰ ﻟﻠﻄﺎﻗﺔ اﻟﺤﺮارﻳﺔ ﻓﻲ ﺗﺼﻤﻴﻢ اﻟﻤﻌﺎﻟﺞ ) ‪ 100 :( thermal design power – TDP‬واط‪.‬‬
‫اﻟﻤﺮآﺰﻳﺔ‬
‫* ﻳﺮﺟﻰ اﻟﺮﺟﻮع إﻟﻰ اﻟﻤﻮﻗﻊ‪ www.biostar.com.tw‬ﻟﻘﺎﺋﻤﺔ دﻋﻢ اﻟﻤﻌﺎﻟﺞ ‪.CPU‬‬
‫ﻣﺠﻤﻮﻋﺔ‬
‫اﻟﺸﺮاﺋﺢ‬
‫)‪AMD A85 FCH (Hi-Fi A85S3‬‬
‫)‪AMD A75 FCH (Hi-Fi A75S3‬‬
‫)‪AMD A55 FCH (Hi-Fi A55S3‬‬
‫ﺗﺪﻋﻢ ﻗﻨﺎة ﻣﺰدوﺟﺔ دي‪ .‬دي‪ .‬ار‪1866 / 1600 / 1333 / 1066 / 800 DDR3 .‬‬
‫اﻟﺬاآﺮة‬
‫‪ x2‬دي‪ .‬دي‪ .‬ار‪ DDR3 .‬ﻓﺘﺤﺎت اﻟﺬاآﺮة اﻟﻤﺰدوﺟﺔ ‪ ،DIMM‬ﺗﺘﺤﻤﻞ آﺤﺪ أﻗﺼﻰ ‪ 32‬ﺟﻴﺠﺎﺑﺎﻳﺖ ذاآﺮة‬
‫آﻞ ﻓﺘﺤﺔ ﻣﺰدوﺟﺔ ‪ DIMM‬ﺗﺘﺤﻤﻞ دون ‪ 512 ECC‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ ‪ 16/8/4/2/1/‬ﺟﻴﺠﺎﺑﺎﻳﺖ دي‪ .‬دي‪ .‬ار ‪DDR3‬‬
‫* ﻳﺮﺟﻰ اﻟﺮﺟﻮع إﻟﻰ اﻟﻤﻮﻗﻊ‪ www.biostar.com.tw‬ﻟﻘﺎﺋﻤﺔ دﻋﻢ اﻟﺬاآﺮة‪.‬‬
‫اﻳﻪ إم دى ‪FCH A85/A75/A55 AMD‬‬
‫اﻟﺘﺨﺰﻳﻦ‬
‫ﺗﺘﺤﻤﻞ راﻳﺪ ‪(FCH A85)AHCI / 10 / 1 / 0 / 5 RAID‬‬
‫ﺗﺘﺤﻤﻞ راﻳﺪ ‪(FCH A75/A55)AHCI / 10 / 1 / 0 RAID‬‬
‫ﺷﺒﻜﺔ ﻣﺤﻠﻴﺔ‬
‫رﻳﻴﺎﻟﺘﻴﻚ رت ل ‪REALTEK RTL 8111F‬‬
‫‪LAN‬‬
‫‪ 1000 / 100 / 10‬ﻣﻴﺠﺎﺑﺎﻳﺖ ‪ /‬اﻟﺜﺎﻧﻴﺔ ‪ ،‬ﺗﺤﺪﻳﺪ ﺗﻠﻘﺎﺋﻲ ‪ ،‬اﻟﻨﺼﻒ ‪ /‬اﻟﻘﺪرة اﻟﻘﺼﻮى اﻟﻤﺰدوﺟﺔ‬
‫اﻟﺘﺮﻣﻴﺰ اﻟﺼﻮﺗﻲ‬
‫‪ALC662‬‬
‫‪ 5.1‬ﻗﻨﻮات ﻋﺎﻟﻴﺔ اﻟﺪﻗﺔ‪Biostar Hi-Fi,‬‬
‫ﻳﻪ إم دى ‪FCH AMD A85/A75‬‬
‫ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ‬
‫ﻋﺎم ‪USB‬‬
‫ﻣﻨﺎﻓﺬ ‪ 6 x‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪ 2 ) 2.0 USB‬ﻓﻲ اﻟﻤﺪاﺧﻞ واﻟﻤﺨﺎرج اﻟﺨﻠﻔﻴﺔ و ‪ 4‬ﻣﻦ ﺧﻼل اﻟﻤﻮزع اﻟﺪاﺧﻠﻲ (‬
‫ﻣﻨﺎﻓﺬ ‪ 4 x‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪ 2 ) 3.0 USB‬ﻓﻲ اﻟﻤﺪاﺧﻞ واﻟﻤﺨﺎرج اﻟﺨﻠﻔﻴﺔ و ‪ 2‬ﻣﻦ ﺧﻼل اﻟﻤﻮزع اﻟﺪاﺧﻠﻲ (‬
‫ﻳﻪ إم دى ‪FCH AMD A55‬‬
‫ﻣﻨﺎﻓﺬ ‪ 8 x‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪ 4 ) 2.0 USB‬ﻓﻲ اﻟﻤﺪاﺧﻞ واﻟﻤﺨﺎرج اﻟﺨﻠﻔﻴﺔ و ‪ 4‬ﻣﻦ ﺧﻼل اﻟﻤﻮزع اﻟﺪاﺧﻠﻲ (‬
‫‪ x 1‬ﻓﺘﺤﺔ ﻣﻨﻔﺬ اﻟﻤﻠﺤﻘﺎت اﻹﺿﺎﻓﻴﺔ ‪PCI‬‬
‫ﻓﺘﺤﺎت اﻟﺘﻮﺳﻊ‬
‫‪ x 1‬ﻓﺘﺤﺔ ﻣﻨﻔﺬ اﻟﻤﻠﺤﻘﺎت اﻹﺿﺎﻓﻴﺔ ‪1 x2.0 PCIe‬‬
‫‪ x 1‬ﻓﺘﺤﺔ ﻣﻨﻔﺬ اﻟﻤﻠﺤﻘﺎت اﻹﺿﺎﻓﻴﺔ ‪16 x2.0 PCIe‬‬
‫‪Hi-Fi A85S3‬‬
‫‪Hi-Fi A75S3‬‬
‫‪Hi-Fi A55S3‬‬
‫‪ PS/2 x 1‬اﻟﻔﺎرة‬
‫‪ PS/2 x 1‬اﻟﻔﺎرة‬
‫‪ PS/2 x 1‬اﻟﻔﺎرة‬
‫‪ PS/2 x 1‬ﻟﻮﺣﺔ اﻟﻤﻔﺎﺗﻴﺢ ﻟﻠﻜﻤﺒﻴﻮت‬
‫‪ PS/2 x 1‬ﻟﻮﺣﺔ اﻟﻤﻔﺎﺗﻴﺢ ﻟﻠﻜﻤﺒﻴﻮت‬
‫‪ PS/2 x 1‬ﻟﻮﺣﺔ اﻟﻤﻔﺎﺗﻴﺢ ﻟﻠﻜﻤﺒﻴﻮت‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 1‬ﻣﻨﻈﻮﻣﺔ اﻟﻌﺮض‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 1‬ﻣﻨﻈﻮﻣﺔ اﻟﻌﺮض‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 1‬ﻣﻨﻈﻮﻣﺔ اﻟﻌﺮض‬
‫اﻟﻤﺮﺋﻲ ‪VGA‬‬
‫اﻟﻤﺮﺋﻲ ‪VGA‬‬
‫اﻟﻤﺮﺋﻲ ‪VGA‬‬
‫اﻟﻤﺪاﺧﻞ‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 1‬واﺟﻬﺔ ﻣﺮﺋﻴﺔ رﻗﻤﻴﺔ‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 1‬واﺟﻬﺔ ﻣﺮﺋﻴﺔ رﻗﻤﻴﺔ‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 1‬واﺟﻬﺔ ﻣﺮﺋﻴﺔ رﻗﻤﻴﺔ‬
‫واﻟﻤﺨﺎرج‬
‫‪HDMI‬‬
‫‪DVI‬‬
‫‪DVI‬‬
‫اﻟﺨﻠﻔﻴﺔ‬
‫ﻓﺘﺤﺔ ﻟﺘﻮﺻﻴﻞ ﻋﺪد ‪ x 1‬اﻟﺸﺒﻜﺔ اﻟﻤﺤﻠﻴﺔ ‪LAN‬‬
‫ﻓﺘﺤﺔ ﻟﺘﻮﺻﻴﻞ ﻋﺪد ‪ x 1‬اﻟﺸﺒﻜﺔ اﻟﻤﺤﻠﻴﺔ ‪LAN‬‬
‫ﻓﺘﺤﺔ ﻟﺘﻮﺻﻴﻞ ﻋﺪد ‪ x 1‬اﻟﺸﺒﻜﺔ اﻟﻤﺤﻠﻴﺔ ‪LAN‬‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 2‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 2‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 4‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم‬
‫‪2.0 USB‬‬
‫‪2.0 USB‬‬
‫‪2.0 USB‬‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 2‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 2‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 3‬ﺟﺎك ﻟﻠﺼﻮت‬
‫‪3.0 USB‬‬
‫‪3.0 USB‬‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 3‬ﺟﺎك ﻟﻠﺼﻮت‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 3‬ﺟﺎك ﻟﻠﺼﻮت‬
‫‪36‬‬
‫‪Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫‪Hi-Fi A85S3‬‬
‫‪Hi-Fi A75S3‬‬
‫‪Hi-Fi A55S3‬‬
‫وﺻﻠﺔ ‪ 6 x SATA 6‬ﺟﻴﺠﺎﺑﺎﻳﺖ ‪/‬‬
‫وﺻﻠﺔ ‪ 6 x SATA 6‬ﺟﻴﺠﺎﺑﺎﻳﺖ ‪/‬‬
‫وﺻﻠﺔ ‪ 3 x SATA 6‬ﺟﻴﺠﺎﺑﺎﻳﺖ ‪/‬‬
‫اﻟﺜﺎﻧﻴﺔ‬
‫اﻟﺜﺎﻧﻴﺔ‬
‫اﻟﺜﺎﻧﻴﺔ‬
‫ﻣﻮزع ‪ x2‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪USB‬‬
‫ﻣﻮزع ‪ x2‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪USB‬‬
‫ﻣﻮزع ‪ x2‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪USB‬‬
‫‪2.0‬‬
‫‪2.0‬‬
‫‪2.0‬‬
‫ﻣﻮزع ‪ x1‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪USB‬‬
‫ﻣﻮزع ‪ x1‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪USB‬‬
‫ﻣﻮﺻﻠﺔ ﻟﻠﻄﺎﻗﺔ ‪ 4 x 1‬دﺑﺎﺑﻴﺲ‬
‫‪3.0‬‬
‫‪3.0‬‬
‫وﺻﻠﺔ ﻟﻠﻄﺎﻗﺔ ‪ 24 x1‬دﺑﻮس‬
‫اﻟﻤﺪاﺧﻞ‬
‫ﻣﻮﺻﻠﺔ ﻟﻠﻄﺎﻗﺔ ‪ 4 x 1‬دﺑﺎﺑﻴﺲ‬
‫ﻣﻮﺻﻠﺔ ﻟﻠﻄﺎﻗﺔ ‪ 4 x 1‬دﺑﺎﺑﻴﺲ‬
‫وﺻﻠﺔ ‪ x 1‬ﻣﺮوﺣﺔ ﺗﺒﺮﻳﺪ وﺣﺪة‬
‫واﻟﻤﺨﺎرج‬
‫وﺻﻠﺔ ﻟﻠﻄﺎﻗﺔ ‪ 24 x1‬دﺑﻮس‬
‫وﺻﻠﺔ ﻟﻠﻄﺎﻗﺔ ‪ 24 x1‬دﺑﻮس‬
‫اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫اﻟﺪاﺧﻠﻴﺔ‬
‫وﺻﻠﺔ ‪ x 1‬ﻣﺮوﺣﺔ ﺗﺒﺮﻳﺪ وﺣﺪة‬
‫وﺻﻠﺔ ‪ x 1‬ﻣﺮوﺣﺔ ﺗﺒﺮﻳﺪ وﺣﺪة‬
‫وﺻﻠﺔ ‪ x1‬ﻣﺮاوح ﺗﺒﺮﻳﺪ اﻟﻤﻨﻈﻮﻣﺔ‬
‫اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫ﻣﻮزع ‪ x 1‬اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫وﺻﻠﺔ ‪ x1‬ﻣﺮاوح ﺗﺒﺮﻳﺪ اﻟﻤﻨﻈﻮﻣﺔ‬
‫وﺻﻠﺔ ‪ x1‬ﻣﺮاوح ﺗﺒﺮﻳﺪ اﻟﻤﻨﻈﻮﻣﺔ‬
‫ﻣﻮزع ‪ x1‬اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬
‫ﻣﻮزع ‪ x 1‬اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻣﻮزع ‪ x 1‬اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻣﻮزع ‪ x1‬ﺳﻴﻤﻮس ﻣﺒﺎﺷﺮ‬
‫ﻣﻮزع ‪ x1‬اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬
‫ﻣﻮزع ‪ x1‬اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬
‫ﻣﻮزع ‪ x1‬ﻓﺘﺤﺔ ﻟﻠﻄﺎﺑﻌﺔ‬
‫ﻣﻮزع ‪ x1‬ﺳﻴﻤﻮس ﻣﺒﺎﺷﺮ‬
‫ﻣﻮزع ‪ x1‬ﺳﻴﻤﻮس ﻣﺒﺎﺷﺮ‬
‫ﻣﻮزع ‪ x1‬ﻓﺘﺤﺔ ﺗﺴﻠﺴﻠﻴﺔ‬
‫ﻣﻮزع ‪ x1‬ﻓﺘﺤﺔ ﻟﻠﻄﺎﺑﻌﺔ‬
‫ﻣﻮزع ‪ x1‬ﻓﺘﺤﺔ ﻟﻠﻄﺎﺑﻌﺔ‬
‫ﻣﻮزع ‪ x1‬ﻓﺘﺤﺔ ﺗﺴﻠﺴﻠﻴﺔ‬
‫ﻣﻮزع ‪ x1‬ﻓﺘﺤﺔ ﺗﺴﻠﺴﻠﻴﺔ‬
‫ﻋﺎﻣﻞ اﻟﺸﻜﻞ‬
‫ﻋﺎﻣﻞ ﺷﻜﻞ ﻣﺪد اﻟﺘﻜﻨﻮﻟﻮﺟﻴﺎ اﻟﻤﺘﻘﺪﻣﺔ ‪ 244 ، microATX‬ﻣﻢ ‪ 191 x‬ﻣﻢ‬
‫أﻧﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ‬
‫وﻳﻨﺪوز إآﺲ ﺑﻲ ‪ / windows xp‬وﻳﻨﺪوز ﻓﻴﺴﺘﺎ ‪ /‬وﻳﻨﺪوز ‪ / 7‬وﻳﻨﺪوز ‪8‬‬
‫اﻟﻤﺪﻋﻮﻣﺔ‬
‫ﺑﻴﻮﺳﺘﺎر ‪ BIOSTAR‬ﺗﺤﺘﻔﻆ ﺑﺤﻖ إﺿﺎﻓﺔ أو أزﻟﺔ اﻟﺪﻋﻢ ﻷي ﻧﻈﺎم ﺗﺸﻐﻴﻞ ﻣﻊ أو ﺑﺪون أﻧﻈﺎر‪.‬‬
‫‪37‬‬
Motherboard Manual
French
Spécifications
Interface de connexion FM2 pour série A AMD processeur
Support Unité
Enveloppe thermique Unité Centrale maximum : 100Watt
Centrale
* Veuillez vous reporter à www.biostar.com.tw pour la liste des supports modèles
d'Unité Centrale.
AMD A85 FCH (Hi-Fi A85S3)
Jeu de puces
AMD A75 FCH (Hi-Fi A75S3)
AMD A55 FCH (Hi-Fi A55S3)
Supporte mémoire DDR3 double canal 800/ 1066/ 1333/ 1600/ 1866
Banc de mémoire 2 x DDR3 DIMM, Supporte max. jusqu’à une mémoire de 32 GB
Mémoire
Chaque module DIMM supporte module DDR3 non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB
* Veuillez vous reporter à www.biostar.com.tw pour la liste des soutien de la
mémoire.
AMD A85/A75/A55 FCH
Stockage
Supporte système RAID 0,1,10, 5 & AHCI (A85 FCH)
Supporte système RAID 0,1,10 & AHCI (A75/A55 FCH)
Realtek RTL 8111F
Réseau local
10/ 100/ 1000 Mb/s auto négociation, capacité bidirectionnelle à l'alternat /
bidirectionnelle simultanée
Codec audio
ALC662
Canaux 5.1, écoute audio de haute définition, Biostar Hi-Fi
AMD A85/A75 FCH
Port 6x USB 2.0 (2 sur les I/O arrières et 4 en interne)
USB
Port 4x USB 3.0 (2 sur les I/O arrières et 2 en interne)
AMD A55 FCH
Port 8x USB 2.0 (4 sur les I/O arrières et 4 en interne)
Connecteur
d’extension
I/O arrirèes
38
1x Fente PCI
1x PCIe 2.0 x1 Fente
1x PCIe 2.0 x16 Fente
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
1x PS/2 Clavier
1x PS/2 Clavier
1x PS/2 Clavier
1x PS/2 Souris
1x PS/2 Souris
1x PS/2 Souris
1x Port VGA
1x Port VGA
1x Port VGA
1x Port HDMI
1x Port DVI
1x Port DVI
1x port LAN
1x port LAN
1x port LAN
2x Port USB 2.0
2x Port USB 2.0
4x Port USB 2.0
2x Port USB 3.0
2x Port USB 3.0
3x entrées audio
3x entrées audio
3x entrées audio
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
Spécifications
I/O en interne
Facteur
d'encombrement
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
6x Connecteur SATA 6.0Gb/s
6x Connecteur SATA 6.0Gb/s
6x Connecteur SATA 3.0Gb/s
2x embases USB 2.0
2x embases USB 2.0
2x embases USB 2.0
1x embases USB 3.0
1x embases USB 3.0
1x 4-Broche de carte
1x 4-Broche de carte
1x 4-Broche de carte
1x 24-Broche de carte
1x 24-Broche de carte
1x 24-Broche de carte
1x Connecteur ventilateur unité
1x Connecteur ventilateur unité
1x Connecteur ventilateur unité
centrale
centrale
centrale
1x Connecteur ventilateur
1x Connecteur ventilateur
1x Connecteur ventilateur
système
système
système
1x Fiche panneau avant
1x Fiche panneau avant
1x Fiche panneau avant
1x Fiche audio avant
1x Fiche audio avant
1x Fiche audio avant
1x Fiche mémoire CMOS vide
1x Fiche mémoire CMOS vide
1x Fiche mémoire CMOS vide
1x Embase port imprimante
1x Embase port imprimante
1x Embase port imprimante
1x Embase port série
1x Embase port série
1x Embase port série
Facteur d'encombrement microATX, 244 mm x 191 mm
Windows XP / Vista / 7/ 8
Support SE
Biostar se réserve le droit d’ajouter ou d'enlever le support pour toute SE avec ou sans
préavis.
39
Motherboard Manual
German
Spezifikationen
Anschluss-FM2 für AMD A-Serie Prozessor
CPU-Unterstütz
ung
Maximale CPU TDP (Thermal Design Power): 100 Watt
* Bitte konsultieren Sie www.biostar.com.tw für CPU-Unterstützungsliste
AMD A85 FCH (Hi-Fi A85S3)
Chipset
AMD A75 FCH (Hi-Fi A75S3)
AMD A55 FCH (Hi-Fi A55S3)
Unterstützt zweikanaliges DDR3 800/ 1066/ 1333/ 1600/ 1866
Festplattenspeic 2 x DDR3 DIMM-SpeicherSlot, Max. Uterstützung bis zu 32 GB-Speicher
her
Jedes DIMM unterstützt nicht-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3-Module
* Bitte konsultieren Sie www.biostar.com.tw für für Speicherunterstützung Liste.
AMD A85/A75/A55 FCH
Arbeitsspeicher
Unterstützt RAID 0,1,10, 5 & AHCI (A85 FCH)
Unterstützt RAID 0,1,10 & AHCI (A75/A55 FCH)
LAN
Audio-Codec
Realtek RTL 8111F
10/ 100/ 1000 Mb Auto-Negotiation, Halb- / Voll-Duplex-fähig
ALC662
5.1 Kanäle, HD-Audio, Biostar Hi-Fi
AMD A85/A75 FCH:
6x USB 2.0-Port (2 hintere I/Os und 4 via interne Header)
USB
4x USB 3.0-Port (2 hintere I/Os und 2 via interne Header)
AMD A55 FCH:
8x USB 2.0-Port (4 hintere I/Os und 4 via interne Header)
1x PCI-Slot
Erweiterungsan
schlüsse
1x PCIe 2.0 x1-Slot
1x PCIe 2.0 x16-Slot
Hintere I/Os
40
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
1x PS/2-Maus
1x PS/2-Maus
1x PS/2-Maus
1x PS/2-Keyboard
1x PS/2-Keyboard
1x PS/2-Keyboard
1x VGA-Port
1x VGA-Port
1x VGA-Port
1x HDMI -Port
1x DVI-Port
1x DVI-Port
1x LAN-Port
1x LAN-Port
1x LAN-Port
2x USB 2.0-Port
2x USB 2.0-Port
4x USB 2.0-Port
2x USB 3.0-Port
2x USB 3.0-Port
3x Audio Jack
3x Audio Jack
3x Audio Jack
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
Spezifikationen
Interne I/Os
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
6x SATA 6.0Gb/s-Verbinung
6x SATA 6.0Gb/s-Verbinung
6x SATA 3.0Gb/s-Verbinung
2x USB 2.0-Header
2x USB 2.0-Header
2x USB 2.0-Header
1x USB 3.0-Header
1x USB 3.0-Header
1x 4-Pin-Stromverbindung
1x 4-Pin-Stromverbindung
1x 4-Pin-Stromverbindung
1x 24-Pin-Stromverbindung
1x 24-Pin-Stromverbindung
1x 24-Pin-Stromverbindung
1x CPU-Ventilatorverbindung
1x CPU-Ventilatorverbindung
1x CPU-Ventilatorverbindung
1x System-Ventilatorverbindung
1x System-Ventilatorverbindung
1x System-Ventilatorverbindung
1x Header für Frontpanel
1x Header für Frontpanel
1x Header für Frontpanel
1x Header für Frontaudio
1x Header für Frontaudio
1x Header für Frontaudio
1x Header für klares CMOS
1x Header für klares CMOS
1x Header für klares CMOS
1x Header für Druckerport
1x Header für Druckerport
1x Header für Druckerport
1x Serieller Port-Header
1x Serieller Port-Header
1x Serieller Port-Header
Formfaktor
microATX Formfaktor, 244 mm x 191 mm
OS-Unterstützu
Windows XP / Vista / 7/ 8
ng
Biostar reserves the right to add or remove support for any OS with or without notice.
41
Motherboard Manual
Italian
Specificazioni
Slot FM2 per processore AMD serie-A
Supporto
processore
Alimentazione di Proiezione Termico (TDP – Thermal Design Power): 100Watt
* Si prega di consultare www.biostar.com.tw per la lista di supporto del
processore.
AMD A85 FCH (Hi-Fi A85S3)
Tipo scheda
AMD A75 FCH (Hi-Fi A75S3)
AMD A55 FCH (Hi-Fi A55S3)
Supporta DDR3 800/ 1066/ 1333/ 1600/ 1866 Doppio Canale
Memoria
2 x DDR3 DIMM Slot di Memoria Supporta fino a 32 GB Memoria
Ogni DIMM supporta non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3 moduli
* Si prega di consultare www.biostar.com.tw per la lista di supporto del memoria.
AMD A85/A75/A55 FCH
Memorizzazione
Supporta RAID 0,1,10, 5 & AHCI (A85 FCH)
Supporta RAID 0,1,10 & AHCI (A75/A55 FCH)
Catena
Codec Audio
Realtek RTL 8111F
10/ 100/ 1000 Mb auto negoziazione, capacita di duplex Meta / Completo
ALC662
Canali Audio di Alta Definizione 5.1, Biostar Hi-Fi
Piattaforma AMD A85/A75 FCH:
Slot 6x USB 2.0 (2 nei ingressi/ uscite posteriore e 4 da distributori interni)
USB
Slot 4x USB 3.0 (2 nei ingressi/ uscite posteriore e 2 da distributori interni)
Piattaforma AMD A55 FCH:
Slot 8x USB 2.0 (4 nei ingressi/ uscite posteriore e 4 da distributori interni)
Slot 1x PCI
Slot di espansione
Slot 1x PCIe 2.0 x1
Slot 1x PCIe 2.0 x16
Ingressi/ Uscite
Posteriore
42
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
Mouse 1x PS/2
Mouse 1x PS/2
Mouse 1x PS/2
Tastiera 1x PS/2
Tastiera 1x PS/2
Tastiera 1x PS/2
Slot 1x VGA
Slot 1x VGA
Slot 1x VGA
Slot 1x HDMI
Slot 1x DVI
Slot 1x DVI
Slot 1x LAN
Slot 1x LAN
Slot 1x LAN
Slot 2x USB 2.0
Slot 2x USB 2.0
Slot 4x USB 2.0
Slot 2x USB 3.0
Slot 2x USB 3.0
Jack audio 3x
Jack audio 3x
Jack audio 3x
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
Specificazioni
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
Connettore 6x SATA 6.0Gb/s
Connettore 6x SATA 6.0Gb/s
Connettore 6x SATA 3.0Gb/s
Distributore 2x USB 2.0
Distributore 2x USB 2.0
Distributore 2x USB 2.0
Distributore 1x USB 3.0
Distributore 1x USB 3.0
Connettore con 4 pin x1
Connettore con 4 pin x1
Connettore con 4 pin x1
Connettore con 24 pin x1
Connettore con 24 pin x1
Connettore con 24 pin x1
Connettore Ventilatore
Connettore Ventilatore
Connettore Ventilatore
processore x1
Ingressi/ Uscite
processore x1
processore x1
Connettore Ventilatore
Interni
Connettore Ventilatore
Connettore Ventilatore
Sistema x1
Sistema x1
Sistema x1
Distributore Pannello Frontale
Distributore Pannello Frontale
Distributore Pannello Frontale
x1
x1
x1
Distributore Audio Frontale x1
Distributore Audio Frontale x1
Distributore Audio Frontale x1
Distributore CMOS Diretto x1
Distributore CMOS Diretto x1
Distributore CMOS Diretto x1
Distributore Slot Stampante x1
Distributore Slot Stampante x1 Distributore Slot Stampante x1 Distributore Slot Serie x1
Distributore Slot Serie x1
Fattore di Forma
Distributore Slot Serie x1
Fattore di Forma microATX, 244 mm x 191 mm
Windows XP / Vista / 7/ 8
Supporto SO
Biostar si riserva il diritto di aggiungere o ritirare il supporto per qualsiasi SO con o
senza preavviso.
43
Motherboard Manual
Japanese
仕様
AMD A-シリーズ プロセッサの Socket FM2
CPU サポート
最大 CPU TDP (Thermal Design Power 最大放熱量):100 W
*CPU サポート リストについては、www.biostar.com.twを参照してください。
AMD A85 FCH (Hi-Fi A85S3)
チップセット
AMD A75 FCH (Hi-Fi A75S3)
AMD A55 FCH (Hi-Fi A55S3)
デュアルチャンネル DDR3 800/ 1066/ 1333/ 1600/ 1866 をサポート
2 x DDR3 DIMM メモリ スロット、 最大 32 GB メモリまでサポート
メモリ
各 DIMM は、 非-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3 モジュールをサポートしてい
ます
*サポートされているメモリのリストについては、www.biostar.com.twを参照してく
ださい。
AMD A85/A75/A55 FCH
保存スペース
RAID 0,1,10, 5 & AHCI のサポート (A85 FCH)
RAID 0,1,10 & AHCI のサポート (A75/A55 FCH)
LAN
Realtek RTL 8111F
10/ 100/ 1000 Mb/s オートネゴーシエーション、半/全 二重通信
オーディオ コーデ
ALC662
ック
5.1 チャンネル, ハイ デフィニション オーディオ, Biostar Hi-Fi
AMD A85/A75 FCH:
6x USB 2.0 ポート (後部 I/O に2つ 及び 内蔵ヘッダー経由に4つ)
USB
4x USB 3.0 ポート (後部 I/O に2つ 及び 内蔵ヘッダー経由に2つ)
AMD A55 FCH:
8x USB 2.0 ポート (後部 I/O に4つ 及び 内蔵ヘッダー経由に4つ)
1x PCI スロット
拡張スロット
1x PCIe 2.0 x1 スロット
1x PCIe 2.0 x16 スロット
後部 I/O
44
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
1x PS/2 キーボード
1x PS/2 キーボード
1x PS/2 キーボード
1x PS/2 マウス
1x PS/2 マウス
1x PS/2 マウス
1x VGA ポート
1x VGA ポート
1x VGA ポート
1x HDMI ポート
1x DVI ポート
1x DVI ポート
1x LAN ポート
1x LAN ポート
1x LAN ポート
2x USB 2.0 ポート
2x USB 2.0 ポート
4x USB 2.0 ポート
2x USB 3.0 ポート
2x USB 3.0 ポート
3x オーディオ ジャック
3x オーディオ ジャック
3x オーディオ ジャック
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
仕様
内蔵 I/O
フォーム ファクタ
サポート OS
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
6x SATA 6.0Gb/s コネクタ
6x SATA 6.0Gb/s コネクタ
6x SATA 3.0Gb/s コネクタ
2x USB 2.0 ヘッダー
2x USB 2.0 ヘッダー
2x USB 2.0 ヘッダー
1x USB 3.0 ヘッダー
1x USB 3.0 ヘッダー
1x 4-Pin パワー コネクタ
1x 4-Pin パワー コネクタ
1x 4-Pin パワー コネクタ
1x 24-Pin パワー コネクタ
1x 24-Pin パワー コネクタ
1x 24-Pin パワー コネクタ
1x CPU ファン コネクタ
1x CPU ファン コネクタ
1x CPU ファン コネクタ
2x システム ファン コネクタ
1x システム ファン コネクタ
1x システム ファン コネクタ
1x フロント パネル ヘッダー
1x フロント パネル ヘッダー
1x フロント パネル ヘッダー
1x フロント オーディオ ヘッ
1x フロント オーディオ ヘッ
1x フロント オーディオ ヘッ
ダー
ダー
ダー
1x クリア CMOS ヘッダー
1x クリア CMOS ヘッダー
1x クリア CMOS ヘッダー
1x プリンター ポート ヘッダ
1x プリンター ポート ヘッダ
1x プリンター ポート ヘッダ
ー
ー
ー
1x シリアル ポート ヘッダー
1x シリアル ポート ヘッダー
1x シリアル ポート ヘッダー
microATX フォーム ファクタ、244 mm x 191 mm
Windows XP / Vista / 7/ 8
Biostar には、通知なしでサポート OS を変更する権限があります。
45
Motherboard Manual
Polish
Specyfikacje techniczne
Gniazdo procesora (Socket) FM2 dla procesorów AMD seria-A
Obsługa procesora
Moc Wydzielanego Ciepła (TDP - Thermal Design Power): 100Watt
* Proszę sprawdzić listę obsługiwanych procesorów na stronie internetowej
www.biostar.com.tw
AMD A85 FCH (Hi-Fi A85S3)
Rodzaj płyty
AMD A75 FCH (Hi-Fi A75S3)
AMD A55 FCH (Hi-Fi A55S3)
Obsługa pamięci DDR3 800/ 1066/ 1333/ 1600/ 1866 Dwukanałowa
2 x DDR3 DIMM Pamięć Gniazda procesora (Slot), Maksymalna wielkość pamięci 32
Pamięć
GB
Każdy DIMM obsługuje jeden moduł non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3
* Proszę sprawdzić listę obsługiwanych pamięć na stronie internetowej
www.biostar.com.tw
AMD A85/A75/A55 FCH
Przechowywanie
Obsługa RAID 0,1,10, 5 & AHCI (A85 FCH)
Obsługa RAID 0,1,10 & AHCI (A75/A55 FCH)
LAN
Codec Audio
Układ RTL 8111F
10/ 100/ 1000 Mb auto negocjacja, pojemność dupleks Połowe / Pełny
ALC662
Kanały Audio wysokiej Definicji 5.1, Biostar Hi-Fi
Płyta AMD A85/A75 FCH:
6 x złącza USB 2.0 (2 przez tylne porty wejścia/ wyjścia oraz 4 przez wewnętrzne porty)
USB
4 x złącza USB 3.0 (2 przez tylne porty wejścia/ wyjścia oraz 2 przez wewnętrzne porty)
Płyta AMD A55 FCH:
8 x złącza USB 2.0 (4 przez tylne porty wejścia/ wyjścia oraz 4 przez wewnętrzne porty)
złącza 1x PCI (Slot)
Złącza rozszerzeń
złącza 1x PCIe 2.0 x1 (Slot)
złącza 1x PCIe 2.0 x16 (Slot)
Tylne porty wejścia/
wyjścia
46
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
Myszka 1x PS/2
Myszka 1x PS/2
Myszka 1x PS/2
Klawiatura 1x PS/2
Klawiatura 1x PS/2
Klawiatura 1x PS/2
Port 1x VGA
Port 1x VGA
Port 1x VGA
Port 1x HDMI
Port 1x DVI
Port 1x DVI
Port 1x LAN
Port 1x LAN
Port 1x LAN
Porty 2x USB 2.0
Porty 2x USB 2.0
Porty 4x USB 2.0
Porty 2x USB 3.0
Porty 2x USB 3.0
Porty audio 3x
Porty audio 3x
Porty audio 3x
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
Specyfikacje techniczne
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
Złącza 6x SATA 6.0Gb/s
Złącza 6x SATA 6.0Gb/s
Złącza 6x SATA3.0Gb/s
Złącza 2x USB 2.0
Złącza 2x USB 2.0
Złącza 2x USB 2.0
Złącza 1x USB 3.0
Złącza 1x USB 3.0
Złącza 4 pionowe x 1
Złącza 4 pionowe x 1
Złącza 4 pionowe x 1
Złącza 24 pionowe x 1
Złącza 24 pionowe x 1
Złącza 24 pionowe x 1
Złącze wentylatora CPU x 1
Złącze wentylatora CPU x 1
Złącze wentylatora CPU x 1
Złącze wentylatora obudowy x
Wewnętrzne porty
Złącze wentylatora obudowy x Złącze wentylatora obudowy x 1
wejścia/ wyjścia
1
1
Złącze przedniego panelu x1
Złącze przedniego panelu x1
Złącze przedniego panelu x1
Złącze audio przedniego
Złącze audio przedniego
Złącze audio przedniego
panelu x1
panelu x1
panelu x1
Złącze bezpośrednie CMOS
Złącze bezpośrednie CMOS
Złącze bezpośrednie CMOS
x1
x1
x1
Złącze port drukarki x1
Złącze port drukarki x1
Złącze port drukarki x1
Port szeregowy x1
Port szeregowy x1
Port szeregowy x1
Obudowa
Obudowa microATX, 244 mm x 191 mm
Windows XP / Vista / 7/ 8
Obsługa OS
Biostar zastrzega sobie prawo do dodania lub wycofania obsługi dla OS, z
wypowiedzeniem lub bez wypowiedzenia.
47
Motherboard Manual
Portuguese
Especificações
Porta FM2 para processador AMD série-A
Suporte
Processador
Alimentação de Design Térmico (TDP – Thermal Design Power): 100Watt
* Por favor consulte www.biostar.com.tw para obter uma lista de suporte do
processador.
AMD A85 FCH (Hi-Fi A85S3)
Tipo Placa Mãe
AMD A75 FCH (Hi-Fi A75S3)
AMD A55 FCH (Hi-Fi A55S3)
Suporta DDR3 800/ 1066/ 1333/ 1600/ 1866 Canal Duplo
Memória
2 x DDR3 DIMM Slot de memória Suporta até 32 GB Memória
Cada DIMM suporta non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3 módulo
* Por favor consulte www.biostar.com.tw para obter uma lista de suporte do memória.
AMD A85/A75/A55 FCH
Armazenamento Suporta RAID 0,1,10, 5 & AHCI (A85 FCH)
Suporta RAID 0,1,10 & AHCI (A75/A55 FCH)
LAN
Codec de Audio
Realtek RTL 8111F
10/ 100/ 1000 Mb auto negociação, capacidade duplex Metade / Cheio
ALC662
Canais de Áudio de Alta Definição 5.1, Biostar Hi-Fi
Plataforma AMD A85/A75 FCH:
Porta 6x USB 2.0 (2 nas entradas/saídas traseiras e 4 pelos Dispositivos internos)
USB
Porta 4x USB 3.0 (2 nas entradas/saídas traseiras e 2 pelos Dispositivos internos)
Plataforma AMD A55 FCH:
Porta 8x USB 2.0 (4 nas entradas/saídas traseiras e 4 pelos Dispositivos internos)
Porta 1x PCI
Slots de
expansão
Porta 1x PCIe 2.0 x1
Porta 1x PCIe 2.0 x16
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
Mouse 1x PS/2
Mouse 1x PS/2
Mouse 1x PS/2
Teclado 1x PS/2
Teclado 1x PS/2
Teclado 1x PS/2
Entradas/Saída
Porta 1x VGA
Porta 1x VGA
Porta 1x VGA
s no painel
Porta 1x HDMI
Porta 1x DVI
Porta 1x DVI
traseiro
Porta 1x LAN
Porta 1x LAN
Porta 1x LAN
Porta 2x USB 2.0
Porta 2x USB 2.0
Porta 4x USB 2.0
Porta 2x USB 3.0
Porta 2x USB 3.0
Soquete audio 3x
Soquete audio 3x
Soquete audio 3x
48
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
Especificações
Conectores na
placa
Fator de Fôrma
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
Conector 6x SATA 6.0Gb/s
Conector 6x SATA 6.0Gb/s
Conector 6x SATA 3.0Gb/s
Dispositivo 2x USB 2.0
Dispositivo 2x USB 2.0
Dispositivo 2x USB 2.0
Dispositivo 1x USB 3.0
Dispositivo 1x USB 3.0
Conector de 4 pinos x1
Conector de 4 pinos x1
Conector de 4 pinos x1
Conector de 24 pinos x1
Conector de 24 pinos x1
Conector de 24 pinos x1
Conector de Ventoinha
Conector de Ventoinha
Conector de Ventoinha
processador x1
processador x1
processador x1
Conector de Ventoinha Sistema
Conector de Ventoinha Sistema
Conector de Ventoinha Sistema
x1
x1
x1
Dispositivo Painel Frontal x1
Dispositivo Painel Frontal x1
Dispositivo Painel Frontal x1
Dispositivo de Audio Frontal x1
Dispositivo de Audio Frontal x1
Dispositivo de Audio Frontal x1
Dispositivo CMOS Direct x1
Dispositivo CMOS Direct x1
Dispositivo CMOS Direct x1
Dispositivo Porta Impressora x1
Dispositivo Porta Impressora x1
Dispositivo Porta Impressora x1
Dispositivo Porta Série x1
Dispositivo Porta Série x1
Dispositivo Porta Série x1
Fator de Fôrma microATX, 244 mm x 191 mm
Windows XP / Vista / 7/ 8
Suporte OS
Biostar reserva seu direito de adicionar ou retirar o suporte para qualquer OS com ou
sem notificação.
49
Motherboard Manual
Russian
Спецификации
Поддержка
Сокет FM2 для процессоров AMD серии A
центрального
Максимальный термопакет центрального процессора (TDP): 100 ватт
процессора
Набор
микросхем
* Перечень поддержки центрального процессора смотрите на www.biostar.com.tw.
AMD A85 FCH (Hi-Fi A85S3)
AMD A75 FCH (Hi-Fi A75S3)
AMD A55 FCH (Hi-Fi A55S3)
Поддерживает двухканальный DDR3 800/ 1066/ 1333/ 1600/ 1866
Память
2 гнезда платы памяти DDR3 DIMM, максимальная память до 32 Гб
Каждый модуль DIMM поддерживает модуль не-ECC 512 Мб/ 1/ 2/ 4/ 8/ 16 Гб DDR3
* Перечень поддержки памяти смотрите на www.biostar.com.tw.
AMD A85/A75/A55 FCH
Накопитель
Поддерживает RAID 0,1,10, 5 & AHCI (A85 FCH)
Поддерживает RAID 0,1,10 & AHCI (A75/A55 FCH)
Локальная сеть
Аудиокодек
Realtek RTL 8111F
Автосогласование 10/ 100/ 1000 Мб/с, работает в полно/полудуплексном режиме
ALC662
Каналы 5.1, высококачественное аудио, Biostar Hi-Fi
AMD A85/A75 FCH:
6 портов USB 2.0 (2 сзади ввода-вывода и 4 через внутренние контакты)
USB
4 портов USB 3.0 (2 сзади ввода-вывода и 2 через внутренние контакты)
AMD A55 FCH:
8 портов USB 2.0 (4 сзади ввода-вывода и 4 через внутренние контакты)
1x гнезда PCI
Гнезда расшир.
1x PCIe 2.0 x1 гнездо
1x PCIe 2.0 x16 гнездо
Hi-Fi A55S3:
Hi-Fi A85S3:
Hi-Fi A75S3:
1 мышь PS/2
1 мышь PS/2
1 мышь PS/2
1 клавиатура PS/2
1 клавиатура PS/2
1 клавиатура PS/2
1 порт VGA
1 порт VGA
1 порт VGA
Задняя плата
1 порт HDMI
1 порт DVI
1 порт DVI
ввода-вывода
1 порт локальной сети
1 порт локальной сети
1 порт локальной сети
2 порта USB 2.0
2 порта USB 2.0
4 порта USB 2.0
2 порта USB 3.0
2 порта USB 3.0
3 гнезд для подключения
3 гнезд для подключения
3 гнезд для подключения
наушников
наушников
наушников
50
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
Спецификации
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
Соединитель 6x SATA 6 Гб/с
Соединитель 6x SATA 6 Гб/с
Соединитель 6x SATA 3 Гб/с
2 контакта USB 2.0
2 контакта USB 2.0
2 контакта USB 2.0
1 контакта USB 3.0
1 контакта USB 3.0
1 4-выводный разъем питания
1 4-выводный разъем питания 1 4-выводный разъем питания 1 24-выводный разъем
Внутр. Плата
ввода-вывода
Конструктив
питания
1 24-выводный разъем
1 24-выводный разъем
питания
питания
1 разъем вентилятора ЦП
1 разъем вентилятора ЦП
1 разъем вентилятора ЦП
1 разъема вентилятора
1 разъема вентилятора
1 разъема вентилятора
системы
системы
системы
1 контакт передней панели
1 контакт передней панели
1 контакт передней панели
1 контакт передней
1 контакт передней
1 контакт передней
аудиопанели
аудиопанели
аудиопанели
1 контакт микросхемы Clear
1 контакт микросхемы Clear
1 контакт микросхемы Clear
CMOS
CMOS
CMOS
1 контакт порта принтера
1 контакт порта принтера
1 контакт порта принтера
1 инфракрасный
1 инфракрасный
1 инфракрасный
пользовательский контакт
пользовательский контакт
пользовательский контакт
1 контакт последовательного
1 контакт последовательного
1 контакт последовательного
порта
порта
порта
Форм-фактор microATX, 244 мм x 191 мм
Windows XP / Vista / 7/ 8
Поддержка ОС
Biostar оставляет за собой право добавлять или удалять поддержку любой ОС, с
уведомлением или без.
51
Motherboard Manual
Spanish
Especificaciones
Ranura FM2 para procesador AMD serie - A
Compatibilidad
con el
procesador
Alimentación de Proyección Térmica (TDP – Thermal Design Power): 100Watt
*Por favor consultar con www.biostar.com.tw para la lista de compatibilidad con el
procesador.
AMD A85 FCH (Hi-Fi A85S3)
Tipo de Placa
AMD A75 FCH (Hi-Fi A75S3)
AMD A55 FCH (Hi-Fi A55S3)
Soporta DDR3 800/ 1066/ 1333/ 1600/ 1866 Doble Canal
2x DDR3 DIMM Ranura de memoria Soporta hasta 32 GB Memoria
Memoria
Cada DIMM soporta un modulo non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3
*Por favor consultar con www.biostar.com.tw para la lista de compatibilidad con el
memoria.
AMD A85/A75/A55 FCH
Almacenamiento
de información
Soporta RAID 0,1,10, 5 & AHCI (A85 FCH)
Soporta RAID 0,1,10 & AHCI (A75/A55 FCH)
LAN
Códec Audio
Realtek RTL 8111F
10/ 100/ 1000 Mb/s auto negociación, capacidad dúplex Mitad/Completo
ALC662
Canales Audio de Alta Definición 5.1, Biostar Hi-Fi
Plataforma AMD A85/A75 FCH:
Ranura 6x USB 2.0 (2 en las entradas/salidas posteriores y 4 por los distribuidores internos)
USB
Ranura 4x USB 3.0 (2 en las entradas/salidas posteriores y 2 por los distribuidores internos)
Plataforma AMD A55 FCH:
Ranura 8x USB 2.0 (4 en las entradas/salidas posteriores y 4 por los distribuidores internos)
Ranura 1x PCI
Ranuras de
Extinción
Ranura 1x PCIe 2.0 x1
Ranura 1x PCIe 2.0 x16
Panel trasero de
E/S
52
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
Ratón 1x PS/2
Ratón 1x PS/2
Ratón 1x PS/2
Teclado 1x PS/2
Teclado 1x PS/2
Teclado 1x PS/2
Ranura 1x VGA
Ranura 1x VGA
Ranura 1x VGA
Ranura 1x HDMI
Ranura 1x DVI
Ranura 1x DVI
Ranura 1x LAN
Ranura 1x LAN
Ranura 1x LAN
Ranura 2x USB 2.0
Ranura 2x USB 2.0
Ranura 4x USB 2.0
Ranura 2x USB 3.0
Ranura 2x USB 3.0
Socket audio 3x
Socket audio 3x
Socket audio 3x
Hi-Fi A85S3/Hi-Fi A75S3/Hi-Fi A55S3
Especificaciones
Conectores en
placa
Hi-Fi A85S3:
Hi-Fi A75S3:
Hi-Fi A55S3:
Conector 6x SATA 6Gb’s
Conector 6x SATA 6Gb’s
Conector 6x SATA 3Gb’s
Distribuidor 2x USB 2.0
Distribuidor 2x USB 2.0
Distribuidor 2x USB 2.0
Distribuidor 1x USB 3.0
Distribuidor 1x USB 3.0
Conector con 4 patillas x1
Conector con 4 patillas x1
Conector con 4 patillas x1
Conector con 24 patillas x1
Conector con 24 patillas x1
Conector con 24 patillas x1
Conector Ventilador procesador
Conector Ventilador procesador
Conector Ventilador procesador
x1
x1
x1
Conector Ventilador Sistema x2
Conector Ventilador Sistema x2
Conector Ventilador Sistema x2
Distribuidor Panel Frontal x1
Distribuidor Panel Frontal x1
Distribuidor Panel Frontal x1
Distribuidor Audio Frontal x1
Distribuidor Audio Frontal x1
Distribuidor Audio Frontal x1
Distribuidor CMOS Directo x1
Distribuidor CMOS Directo x1
Distribuidor CMOS Directo x1
Distribuidor Ranura Impresora
Distribuidor Ranura Impresora
Distribuidor Ranura Impresora
x1
x1
x1
Distribuidor Ranura Serie x1
Distribuidor Ranura Serie x1 Distribuidor Ranura Serie x1
Factor de Forma
Factor de Forma microATX, 244 mm x 191 mm
Windows XP / Vista / 7/ 8
Soporte OS
Biostar reserva su derecho de añadir o retirar el soporte para cada OS con o sin
notificación.
2012/12/12
53
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement