Biostar TA57A Owner's Manual
TA57A Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Dichiarazione di conformità
sintetica
Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002
Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive
2004/108/CE, 2006/95/CE e
1999/05/CE
quando ad esso applicabili
Short Declaration of conformity
We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives
2004/108/CE, 2006/95/CE and
1999/05/CE
whenever these laws may be applied
Table of Contents
Chapter 1: Introduction ........................................ 1
1.1
1.2
1.3
1.4
1.5
Before You Start ................................................................................ 1
Package Checklist ............................................................................. 1
Motherboard Features...................................................................... 2
Rear Panel Connectors ..................................................................... 3
Motherboard Layout......................................................................... 4
Chapter 2: Hardware Installation .......................... 5
2.1
2.2
2.3
2.4
Installing Central Processing Unit (CPU)....................................... 5
FAN Headers...................................................................................... 7
Installing System Memory ................................................................ 8
Connectors and Slots ....................................................................... 10
Chapter 3: Headers & Jumpers Setup .................. 13
3.1
3.2
How to Setup Jumpers .................................................................... 13
Detail Settings.................................................................................. 13
Chapter 4: RAID Functions .................................. 17
4.1
4.2
4.3
Operating System............................................................................ 17
Raid Arrays ...................................................................................... 17
How RAID Works............................................................................. 17
Chapter 5: Useful Help ........................................ 20
5.1
5.2
5.3
5.4
5.5
Driver Installation Note.................................................................. 20
Software............................................................................................ 21
Extra Information............................................................................ 25
AMI BIOS Beep Code....................................................................... 27
Troubleshooting............................................................................... 28
Appendix: SPEC In Other Languages ................... 30
German.................................................................................................................. 30
French .................................................................................................................... 32
Italian..................................................................................................................... 34
Spanish ................................................................................................................... 36
Portuguese ............................................................................................................ 38
Polish...................................................................................................................... 40
Russian ................................................................................................................... 42
Arabic..................................................................................................................... 44
Japanese ................................................................................................................ 46
TA57A
CHAPTER 1: INTRODUCTION
1.1
BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
„
„
„
„
„
„
„
1.2
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
The operating temperatures of the computer should be
0 to 45 degrees Celsius.
PACKAGE CHECKLIST
Serial ATA Cable X2
Rear I/O Panel for ATX Case X1
User’s Manual X1
Fully Setup Driver DVD X1
Note: The package contents may be different due to area or your motherboard version.
1
Motherboard Manual
1.3
MOTHERBOARD FEATURES
SPEC
Socket FM1
AMD 64 Architecture enables 32 and 64 bit
AMD A-Series / E2-Series processors
computing
CPU
Chipset
AMD A55
ITE 8728
Environment Control initiatives
Provides the most commonly used legacy
H/W Monitor
Super I/O functionality
Fan Speed Controller
Low Pin Count Interface
ITE's "Smart Guardian" function
Super I/O
DDR3 DIMM Slots x 4
Main
Max Memory Capacity 32GB
Dual Channel Mode DDR3 memory module
Memory
Each DIMM supports 512MB/
Supports DDR3 800/1066/1333/1600/1866
1GB/2GB/4GB/8GB DDR3
Data transfer rates up to 3 Gb/s.
SATA II
Integrated Serial ATA Controller
SATA Version 2.0 specification compliant.
RAID 0,1,10 support
10 / 100 Mb/s / 1Gb/s auto negotiation
LAN
RTL8111E
Half / Full duplex capability
5.1channels audio out
Sound
VT1708B
Supports HD Audio
PCI Express Gen2 x16 Slot
x2
Supports PCI-E Gen2 x16, x4 expansion cards
PCI Express Gen2 x1 Slot
x2
Supports PCI-E Gen2 x1 expansion cards
PCI Slot
x2
Supports PCI expansion cards
SATA Connector
x6
Each connector supports 1 SATA device
Connectors Front Panel Connector
x1
Supports front panel facilities
Front Audio Connector
x1
Supports front panel audio function
S/PDIF out Connector
x1
Supports digital audio out function
CPU Fan Header
x1
CPU Fan power supply (with Smart Fan function)
System Fan Header
x2
System Fan Power supply
CMOS clear Header
x1
Restore CMOS data to factory default
Slots
On Board
2
TA57A
SPEC
USB2.0 Connector
x2
Each connector supports 2 front panel USB2.0 ports
Printer Port Connector
x1
Each connector supports 1 Printer port
Power Connector (24-Pin)
x1
Connects to Power supply
Power Connector (4-Pin)
x1
Connects to Power supply
PS/2 Keyboard
x1
Connects to PS/2 Keyboard
PS/2 Mouse
x1
Connects to PS/2 Mouse
Back Panel Serial Port
x1
Connects to RS-232 Port
I/O
LAN port
x1
Connect to RJ-45 ethernet cable
USB2.0 Port
x4
Connect to USB2.0 devices
Audio Jack
x3
Provide Audio-In/Out and Mic. connection
Board Size
220 mm (W) x 305 mm (L)
OS Support Windows XP / Vista / 7
ATX
Biostar reserves the right to add or remove support
for any OS With or without notice.
1.4
REAR PANEL CONNECTORS
P S /2
Mou se
LA N
L ine In /
S urrou nd
L ine O ut
M ic In 1/
B as s/ Ce nte r
P S /2
K e yb oa rd
CO M1
US B 2.0 X 2
US B 2 .0 X 2
3
Motherboard Manual
1.5
MOTHERBOARD LAYOUT
KBMS1
CPU_FAN1
DDR3_B2
DDR3_B1
DDR3_A2
DDR3_A1
COM1
ATXPWR2
ATXPWR1
USB1
RJ45USB1
AUDIO1
SYS_FAN2
LAN
PEX16_1
PEX1_1
Super
I/O
SATA3
BAT1
AMD
A55
SATA2
PEX1_2
SATA1
PEX16_2
PCI1
Codec
BIOS
JCMOS1
PCI2
JSPDIFOUT1
F_AUDIO1
SYS_FAN1
J_PRINT1
Note: ■ represents the 1st pin.
4
F_USB2
F_USB1
PANEL1
TA57A
CHAPTER 2: HARDWARE INSTALLATION
2.1
INSTALLING CENTRAL PROCESSING UNIT (CPU)
Step 1: Pull the lever toward direction A from the socket and then raise the
lever up to a 90-degree angle.
Step 2: Look for the white triangle on socket, and the gold triangle on
CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.
5
Motherboard Manual
Step 3: Hold the CPU down firmly, and then close the lever toward direct
B to complete the installation.
Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU
FAN power cable to the CPU_FAN1. This completes the
installation.
6
TA57A
2.2
FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
CPU_FAN1: CPU Fan Header
1
4
Pin
1
2
3
4
Assignment
Ground
+12V
FAN RPM rate
sense
Smart Fan
Control (By Fan)
SYS_FAN1: System Fan Header
SYS_FAN2: NorthBridge Fan Header
S YS _FA N2
3
1
1
Pin
1
2
3
Assignment
Ground
+12V
FAN RPM
rate sense
3
S YS _FA N1
Note:
CPU_FAN1, SYS_FAN1/2 support 4-pin and 3-pin head connectors. When connecting
with wires onto connectors, please note that the red wire is the positive and should be
connected to pin#2, and the black wire is Ground and should be connected to GND.
7
Motherboard Manual
2.3
INSTALLING SYSTEM MEMORY
8
D DR 3_B2
DDR 3_B1
DDR 3_A2
DDR 3_A1
A. DDR3 Modules
1.
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2.
Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
TA57A
B. Memory Capacity
DIMM Socket
Location
DDR3 Module
DDR3_A1
512MB/1GB/2GB/4GB/8GB
DDR3_A2
512MB/1GB/2GB/4GB/8GB
DDR3_B1
512MB/1GB/2GB/4GB/8GB
DDR3_B2
512MB/1GB/2GB/4GB/8GB
Total Memory
Size
Max is 32GB.
C. Dual Channel Memory Installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2
Enabled
O
X
O
X
Enabled
X
O
X
O
Enabled
O
O
O
O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
D. DDR Speed Support
Please refer to the following table for DDR speed reference:
# of DIMM per Channel
# of Ranks per DIMM
Max DDR Speed Grade
for 1.50V DIMM
1 of 1 UDIMM
xR
DDR3-1866
1 of 2 UDIMMs
xR
DDR3-1600
2 of 2 UDIMMs
1R, 1R
DDR3-1600
2 of 2 UDIMMs
2R, xR
DDR3-1333
Note:
xR: Single or double side memory moudule
1R: Single side memory moudule
2R: Double side memory moudule
9
Motherboard Manual
2.4
CONNECTORS AND SLOTS
SATA1~SATA6: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 6 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.
Pin
1
2
3
4
5
6
7
SATA1 SATA3
SATA2
Assignment
Ground
TX+
TXGround
RXRX+
Ground
ATXPWR2: ATX Power Source Connector
This connector provides +12V to CPU power circuit.
10
1
4
2
3
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
TA57A
ATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Assignment
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
12
24
1
13
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Assignment
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V
Note:
Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2
connectors have been plugged-in.
PCI1/PCI2: Peripheral Component Interconnect Slots
This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI 1
PCI 2
11
Motherboard Manual
PEX16_1: PCI-Express Gen2 x16 Slot
-
PCI-Express 2.0 compliant.
Maximum theoretical realized bandwidth of 8GB/s simultaneously per
direction, for an aggregate of 16GB/s totally.
PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.
2X bandwidth over the PCI-Express 1.1 architecture.
PEX1_1/PEX1_2: PCI-Express Gen2 x1 Slots
-
PCI-Express 2.0 compliant.
Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.
PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
PEX16_2: PCI-Express Gen2 x4 Slot
-
PCI-Express 2.0 compliant.
Data transfer bandwidth up to 2GB/s per direction; 4GB/s in total.
PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
PE X16_1
PEX1_1
PEX1_2
PE X16_2
12
TA57A
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1
HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened
3.2
Pin closed
Pin1-2 closed
DETAIL SETTINGS
PANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.
PWR_LED
On/Off
+ + -
9
1
16
8
+ -
RST
SPK
HLED
Pin
1
2
3
4
5
6
7
8
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Function
Speaker
Connector
Hard drive
LED
Reset button
Pin
9
10
11
12
13
14
15
16
Assignment
N/A
N/A
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Function
N/A
N/A
Power LED
Power-on button
13
Motherboard Manual
JCMOS1: Clear CMOS Header
Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.
1
3
Pin 1-2 Close:
Normal Operation
(default).
1
3
1
3
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1.
2.
3.
4.
5.
6.
Remove AC power line.
Set the jumper to “Pin 2-3 close”.
Wait for five seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
Load Optimal Defaults and save settings in CMOS.
F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel
These headers allow user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
F_ US B 2 F_ USB 1
14
2
10
1
9
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
Key
NC
TA57A
F_AUDIO1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header supports HD and AC’97 audio front panel connector.
2
10
1
9
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense
JSPDIFOUT1: Digital Audio-out Connector
This connector allows user to connect the PCI bracket SPDIF output header.
Pin
1
2
3
1
Assignment
+5V
SPDIF_OUT
Ground
3
15
Motherboard Manual
J_PRINT1: Printer Port Connector
This header allows you to connector printer on the PC.
2
26
1
16
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Assignment
25
-Strobe
-ALF
Data 0
Pin
14
15
16
Assignment
Ground
Data 6
Ground
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5
17
18
19
20
21
22
23
24
25
26
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key
TA57A
CHAPTER 4: RAID FUNCTIONS
4.1
OPERATING SYSTEM
Supports Windows Vista and Windows 7.
4.2
RAID ARRAYS
RAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for
many applications.
RAID 1: RAID 1 defines techniques for mirroring data.
RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1.
4.3
HOW RAID WORKS
RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a large file into smaller blocks and performs disk reads and writes across multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment. This
technique reduces overall disk access time and offers high bandwidth.
Features and Benefits
­
­
­
­
­
Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the
platform.
Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.
Benefits: provides increased data throughput, especially for large files. No
capacity loss penalty for parity.
Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.
Fault Tolerance: No.
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
17
Motherboard Manual
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on a
second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the
active volume or drive is corrupted or becomes unavailable because of a hardware failure.
RAID techniques can be applied for high-availability solutions, or as a form of automatic
backup that eliminates tedious manual backups to more expensive and less reliable
media.
Features and Benefits
­
­
­
­
­
Drives: Minimum 2, and maximum is 2.
Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
Fault Tolerance: Yes.
Block 1
Block 2
Block 3
18
Block 1
Block 2
Block 3
TA57A
RAID 10:
RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 10
solution for improved resiliency, performance and rebuild performance.
Features and Benefits
­
­
­
­
Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID levels
in an array, and allows for spare disks.
Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
Fault Tolerance: Yes.
Block 1
Block 3
Block 5
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
Block 2
Block 4
Block 6
19
Motherboard Manual
CHAPTER 5: USEFUL HELP
5.1
DRIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
20
TA57A
5.2
SOFTWARE
Installing Software
1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.
2. Select Software Installation, and then click on the respective software
title.
3. Follow the on-screen instructions to complete the installation.
Launching Software
After the installation process, you will see the software icon “eHOT Line” /
“BIOS Update” appears on the desktop. Double-click the icon to launch the
utility.
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.
Before you use this utility, please set Outlook Express as your default e-mail client application program.
represents important
*informa
ti on that you
must provide. Wi thout
this information, you may
not be able to send out
the mail.
This bl ock will show
the i nformation which
would be collected in
the mail .
conditi on
*Describe
of your system.
your area or
*Select
the area cl ose to you.
Provide the e-ma il
address that you would
like to send the copy to.
e the name of
*Provid
the memory module
manufacturer.
Provide the name of
the power suppl y
manufacturer and the
model no.
Send the mail out.
Exi t thi s dialog.
Save these in forma tion to a .txt file
21
Motherboard Manual
After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.
If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.
Enter the file name and then click
“Save”. Your system information
will be saved to a .txt file.
Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.
We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.
If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web
http://www.biostar.com.tw/app/en-us/about/contact.php for getting
our contact information.
22
TA57A
BIOS Update
BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.
AWARD BIOS
Show current BIOS information
AMI BIOS
Clear CMOS function
(Only for AWARD BIOS)
Save current BIOS
to a .bin file
Update BIOS
with a BIOS file
<Backup BIOS>
Once click on this button, the saving
dialog will show. Choose the
position to save file and enter file
name. (We recommend that the file
name should be English/number
and no longer than 7 characters.)
Then click Save.
23
Motherboard Manual
<Update BIOS>
Before doing this, please download the proper BIOS file from the website.
For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.
Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.
After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.
The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.
After the BIOS Update process, click on
OK to restart the system.
While the system boots up and the full screen logo shows, press
key to enter BIOS setup.
<Delete>
In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.
All the information and content above about the software are subject to be changed
without notice. For better performance, the software is being continuously updated.
The information and pictures described above are for your reference only. The actual
information and settings on board may be slightly different from this manual.
24
TA57A
5.3
EXTRA INFORMATION
CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
25
Motherboard Manual
BIO-Flasher
BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.
The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.
Updating BIOS with BIO-Flasher
1. Go to the website to download the latest BIOS file for the motherboard.
2. Then, save the BIOS file into a USB pen drive or a floppy disk.
3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.
4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.
5. The utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.
6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.
z
z
26
This utility only allows storage device with FAT32/16 format and single
partition.
Shutting down or resetting the system while updating the BIOS will lead to
system boot failure.
TA57A
5.4
AMI BIOS BEEP CODE
Boot Block Beep Codes
Number of Beeps
1
2
3
4
5
7
10
11
12
13
Description
No media present. (Insert diskette in floppy drive A:)
“AMIBOOT.ROM” file not found in root directory of diskette in
A:
Insert next diskette if multiple diskettes are used for recovery
Flash Programming successful
File read error
No Flash EPROM detected
Flash Erase error
Flash Program error
“AMIBOOT.ROM” file size error
BIOS ROM image mismatch (file layout does not match
image present in flash device)
POST BIOS Beep Codes
Number of Beeps
1
3
6
7
8
Description
Memory refresh timer error
Base memory read/write test error
Keyboard controller BAT command failed
General exception error (processor exception interrupt error)
Display memory error (system video adapter)
Troubleshooting POST BIOS Beep Codes
Number of Beeps
1, 3
6, 7
8
Troubleshooting Action
Reseat the memory, or replace with known good modules.
Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.
z If beep codes are generated when all other expansion
cards are absent, consult your system manufacturer’s
technical support.
z If beep codes are not generated when all other expansion
cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.
If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.
27
Motherboard Manual
5.5
TROUBLESHOOTING
Probable
1.
There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work
2.
Indicator light on keyboard does
not shine.
System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.
System does not boot from a hard disk
drive, but can be booted from optical
drive.
Solution
1.
2.
3.
Make sure power cable is
securely plugged in.
Replace cable.
Contact technical support.
Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.
1.
Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from an optical
1.
Back up data and applications
drive. Hard disks can be read,
files.
applications can be used, but system 2.
Reformat the hard drive.
fails to boot from a hard disk.
Re-install applications and data
using backup disks.
Screen message shows “Invalid
Review system’s equipment. Make sure
Configuration” or “CMOS Failure.”
correct information is in setup.
System cannot boot after user installs a 1.
Set master/slave jumpers
second hard drive.
correctly.
2.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
28
TA57A
This page is intentionally left blank.
29
Motherboard Manual
APPENDIX: SPEC IN OTHER LANGUAGES
GERMAN
Spezifikationen
CPU
Chipsatz
Sockel FM1
Die AMD 64-Architektur unterstützt eine 32-Bit- und
AMD A-Series / E2-Series Prozessoren
64-Bit-Datenverarbeitung
AMD A55
ITE 8728
Super E/A
Umgebungskontrolle,
Bietet die häufig verwendeten alten Super Hardware-Überwachung
E/A-Funktionen.
Lüfterdrehzahl-Controller
Low Pin Count-Schnittstelle
"Smart Guardian"-Funktion von ITE
DDR3 DIMM-Steckplätze x 4
Dual-Kanal DDR3 Speichermodul
Arbeitsspeich Max. 32GB Arbeitsspeicher
er
Unterstützt DDR3 800/1066/1333/1600/1866
Jeder DIMM unterstützt 512MB/
Unterstützt DDR3 2000 (OC)
1GB/2GB/4GB/8GB DDR3.
Datentransferrate bis zu 3 Gb/s
SATA II
Integrierter Serial ATA-Controller
Konform mit der SATA-Spezifikation Version 2.0
Unterstützt RAID 0,1,10
LAN
10 / 100 / 1000 Mb/s Auto-Negotiation
RTL8111E
Halb-/ Vollduplex-Funktion
5.1-Kanal-Audioausgabe
Audio-Codec VT1708B
Steckplätze
PCI Express Gen2 x16 Steckplatz
x2
PCI Express Gen2 x1 Steckplatz
x2
PCI Steckplatz
x2
Onboard-Ans SATA-Anschluss
chluss
30
Unterstützt High-Definition Audio
x6
Jeder Anschluss unterstützt 1 SATA-Laufwerk
Fronttafelanschluss
x1
Unterstützt die Fronttafelfunktionen
Front-Audioanschluss
x1
Unterstützt die Fronttafel-Audioanschlussfunktion
S/PDIF Ausgangsanschluss
x1
Unterstützt die digitale Audioausgabefunktion
CPU-Lüfter-Sockel
x1
System-Lüfter-Sockel
x2
CPU-Lüfterstromversorgungsanschluss (mit Smart
Fan-Funktion)
System-Lüfter-Stromversorgungsanschluss
TA57A
Spezifikationen
"CMOS löschen"-Sockel
x1
USB2.0-Anschluss
x2
Jeder Anschluss unterstützt 2
Fronttafel-USB2.0-Anschlüsse
Druckeranschluss Anschluss
x1
Stromanschluss (24-polig)
x1
Stromanschluss (4-polig)
x1
PS/2-Tastatur
x1
PS/2-Maus
x1
Rückseiten-E Serieller Anschluss
/A
Jeder Anschluss unterstützt 1 Druckeranschluss
x1
LAN-Anschluss
x1
USB2.0-Anschluss
x4
Audioanschluss
x3
Platinengröße 220 mm (B) X 305 mm (L)
Biostar behält sich das Recht vor, ohne Ankündigung
OS-Unterstüt
zung
Windows XP / Vista / 7
die Unterstützung für ein Betriebssystem
hinzuzufügen oder zu entfernen.
31
Motherboard Manual
FRENCH
SPEC
UC
Socket FM1
Processeurs AMD A-Series / E2-Series
Chipset
Super E/S
L'architecture AMD 64 permet le calcul 32 et 64 bits
AMD A55
ITE 8728
Initiatives de contrôle environnementales,
Fournit la fonctionnalité de Super E/S
Moniteur de matériel
patrimoniales la plus utilisée.
Contrôleur de vitesse de ventilateur
Interface à faible compte de broches
Fonction "Gardien intelligent" de l'ITE
Fentes DDR3 DIMM x 4
Mémoire
Capacité mémoire maximale de 32Go
principale
Chaque DIMM prend en charge des DDR3
de 512Mo/1Go/2Go/4Go/8Go
Module de mémoire DDR3 à mode à double voie
Prend en charge la DDR3 800/1066/1333/1600/1866
Prend en charge la DDR3 2000 (OC)
Taux de transfert jusqu'à 3 Go/s.
SATA II
Conforme à la spécification SATA Version 2.0
Contrôleur Serial ATA intégré
Prise en charge RAID 0,1,10
LAN
10 / 100 / 1000 Mb/s négociation automatique
RTL8111E
Half / Full duplex capability
Sortie audio à 5.1 voies
Codec audio VT1708B
Fentes
Connecteur
embarqué
32
Prise en charge de l'audio haute définition
Fente PCI Express Gen2 x16
x2
Fente PCI Express Gen2 x1
x2
Fente PCI
x2
Connecteur SATA
x6
Connecteur du panneau avant
x1
Prend en charge les équipements du panneau avant
Connecteur Audio du panneau avant x1
Prend en charge la fonction audio du panneau avant
Connecteur de sortie S/PDIF
x1
Prend en charge la fonction de sortie audio numérique
Embase de ventilateur UC
x1
Embase de ventilateur système
x2
Embase d'effacement CMOS
x1
Chaque connecteur prend en charge 1 périphérique
SATA
Alimentation électrique du ventilateur UC (avec fonction
de ventilateur intelligent)
Alimentation électrique du ventilateur système
TA57A
SPEC
Connecteur USB2.0
x2
Chaque connecteur prend en charge 2 ports USB2.0 de
panneau avant
Connecteur de Port d'imprimante
x1
Connecteur d'alimentation
x1
Chaque connector prend en charge 1 Port d'imprimante
(24 broches)
Connecteur d'alimentation
x1
(4broches)
E/S du
panneau
arrière
Dimensions
de la carte
Clavier PS/2
x1
Souris PS/2
x1
Port série
x1
Port LAN
x1
Port USB2.0
x4
Fiche audio
x3
220 mm (l) X 305 mm (H)
Support SE Windows XP / Vista / 7
Biostar se réserve le droit d'ajouter ou de supprimer le
support de SE avec ou sans préavis.
33
Motherboard Manual
ITALIAN
SPECIFICA
CPU
Chipset
Socket FM1
L’architettura AMD 64 abilita la co mputazione 32
Processori AMD A-Series / E2-Series
e 64 bit
AMD A55
ITE 8728
Super I/O
Funzioni di controllo dell’ambiente:
Fornisce le funzionalità legacy Super Monitoraggio hardware
I/O usate più comunemente.
Controller velocità ventolina
Interfaccia LPC (Low Pin Count)
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR3 x 4
Modulo di memoria DDR3 a canale doppio
Memoria
Capacità massima della memoria 32GB
principale
Ciascun DIMM supporta DDR3
Supporto di DDR3 800/1066/1333/1600/1866
Supporto di DDR3 2000 (OC)
512MB/1GB/2GB/4GB/8GB
Velocità di trasferimento dei dati fino a 3 Gb/s.
SATA II
Controller Serial ATA integrato
Compatibile specifiche SATA Versione 2.0
Supporto RAID 0,1,10
LAN
Negoziazione automatica 10 / 100 / 1000 Mb/s
RTL8111E
Capacità Half / Full Duplex
Codec
audio
Uscita audio 5.1 canali
VT1708B
Supporto audio High-Definit ion (HD)
Alloggio PCI Express Gen2 x16 x2
Alloggi
Alloggio PCI Express Gen2 x1
x2
Alloggio PCI
x2
Connettori Connettore SATA
su scheda
x6
Ciascun connettore supporta 1 unità SATA
Connettore pannello frontale
x1
Supporta i servizi del pannello frontale
Connettore audio frontale
x1
Supporta la funzione audio pannello frontale
Connettore output S/PDIF
x1
Supporta la funzione d’output audio digitale
Collettore ventolina CPU
x1
Alimentazione ventolina CPU (con funzione Smart
Fan)
Collettore ventolina sistema
34
x2
Alimentazione ventolina di sistema
TA57A
SPECIFICA
Collettore cancellaz ione CMOS
x1
Connettore USB2.0
x2
Ciascun connettore supporta 2 porte USB2.0
pannello frontale
Connettore Porta stampante
x1
Connettore alimentazione
x1
Ciascun connettore supporta 1 Porta stampante
(24 pin)
Connettore alimentazione
x1
(4pin)
I/O
Tastiera PS/2
x1
Mouse PS/2
x1
Porta seriale
x1
Porta LAN
x1
Porta USB2.0
x4
Connettore audio
x3
pannello
posteriore
Dimension 220 mm (larghezza) x 305 mm
i scheda
(altezza)
Biostar si riserva il diritto di aggiungere o
Sistemi
operativi
supportati
Windows XP / Vista / 7
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
35
Motherboard Manual
SPANISH
Especificación
CPU
Conjunto de
chips
Conector FM1
La arquitectura AMD 64 permite el procesado de 32 y
Procesadores AMD A-Series / E2-Series
64 bits
AMD A55
ITE 8728
Súper E/S
Iniciativas de control de entorno,
Le ofrece las funcionalidades heredadas de Monitor hardware
uso más común Súper E/S.
Controlador de velocidad de ventilador
Interfaz de cuenta Low Pin
Función "Guardia inteligente" de ITE
Ranuras DIMM DDR3 x 4
Módulo de memoria DDR3 de canal Doble
Memoria
Capacidad máxima de memoria de 32GB
principal
Cada DIMM admite DDR de
Admite DDR3 de 800/1066/1333/1600/1866
Admite DDR3 de 2000 (OC)
512MB/1GB/2GB/4GB/8GB
Tasas de transferencia de hasta 3 Gb/s.
SATA II
Controlador ATA Serie Integrado
Compatible con la versión SATA 2.0
Admite RAID 0,1,10
Red Local
Negociación de 10 / 100 / 1000 Mb/s
RTL8111E
Funciones Half / Full dúplex
Códecs de
sonido
Ranuras
Salida de sonido de 5.1 canales
VT1708B
Soporte de sonido de Alta Definición
Ranura PCI Express Gen2 x16
X2
Ranura PCI express Gen2 x1
X2
Ranura PCI
X2
Conectores Conector SATA
en placa
X6
Cada conector soporta 1 dispositivos SATA
Conector de panel frontal
X1
Soporta instalaciones en el panel frontal
Conector de sonido frontal
X1
Soporta funciones de sonido en el panel frontal
Conector de salida S/PDIF
X1
Soporta función de salida de sonido digital
Cabecera de ventilador de CPU
X1
Fuente de alimentación de ventilador de CPU (con
función Smart Fan)
36
TA57A
Especificación
Cabecera de ventilador de sistema X2
Fuente de alimentación de ventilador de sistema
Cabecera de borrado de CMOS
X1
Conector USB2.0
X2
Cada conector soporta 2 puertos USB2.0 frontales
Conector Puerto de impresora
X1
Cada conector soporta 1 Puerto de impresora
Conector de alimentación
X1
(24 patillas)
Conector de alimentación
X1
(4patillas)
Panel
trasero de
E/S
Tamaño de
la placa
Teclado PS/2
X1
Ratón PS/2
X1
Puerto serie
X1
Puerto de red local
X1
Puerto USB2.0
X4
Conector de sonido
X3
220 mm. (A) X 305 mm. (H)
Soporte de
sistema
operativo
Biostar se reserva el derecho de añadir o retirar el
Windows XP / Vista / 7
soporte de cualquier SO con o sin aviso previo.
37
Motherboard Manual
PORTUGUESE
ESPECIFICAÇÕES
CPU
Chipset
Socket FM1
A arquitectura AMD 64 permite uma computação de 32
Processadores AMD A-Series / E2-Series
e 64 bits
AMD A55
ITE 8728
Especificaçã
o Super I/O
Iniciativas para controlo do ambiente
Proporciona as funcionalidades mais
utilizadas em termos da especificação
Super I/O.
Monitorização do hardware
Controlador da velocidade da ventoinha
Função "Smart Guardian" da ITE
Interface LPC (Low Pin Count).
Ranhuras DIMM DDR3 x 4
Memória
principal
Capacidade máxima de memória: 32GB
Módulo de memória DDR3 de canal duplo
Cada módulo DIMM suporta uma
Suporta módulos DDR3 800/1066/1333/1600/1866
memória DDR3 de 512MB/
Suporta módulos DDR3 2000 (OC)
1GB/2GB/4GB/8GB
Velocidades de transmissão de dados até 3 Gb/s.
SATA II
Controlador Serial ATA integrado
Compatibilidade com a especificação SATA versão 2.0
Suporta as funções RAID 0,1,10
LAN
Codec de
som
Ranhuras
38
Capacidade semi/full-duplex
Saída de áudio de 5.1 canais
VT1708B
Suporta a especificação High-Definition Audio
Ranhura PCI Express Gen2 x16
x2
Ranhura PCI Express Gen2 x1
x2
Ranhura PCI
x2
Conectores Conector SATA
na placa
Auto negociação de 10 / 100 / 1000 Mb/s
RTL8111E
x6
Cada conector suporta 1 dispositivo SATA
Conector do painel frontal
x1
Para suporte de várias funções no painel frontal
Conector de áudio frontal
x1
Suporta a função de áudio no painel frontal
Conector de saída S/PDIF
x1
Suporta a saída de áudio digital
Conector da ventoinha da CPU
x1
Conector da ventoinha do sistema
x2
Alimentação da ventoinha da CPU (com a função Smart
Fan)
Alimentação da ventoinha do sistema
TA57A
ESPECIFICAÇÕES
Conector para limpeza do CMOS
x1
Conector USB2.0
x2
Cada conector suporta 2 portas USB2.0 no painel
frontal
Conector da para impressora
x1
Conector de alimentação
x1
Cada conector suporta 1 Porta para impressora
(24 pinos)
Conector de alimentação
x1
(4 pinos)
Entradas/S
aídas no
painel
Teclado PS/2
x1
Rato PS/2
x1
Porta série
x1
Porta LAN
x1
Porta USB2.0
x4
Tomada de áudio
x3
traseiro
Tamanho
da placa
220 mm (L) X 305 mm (A)
A Biostar reserva-se o direito de adicionar ou remover
Sistemas
operativos
suportados
Windows XP / Vista / 7
suporte para qualquer sistema operativo com ou sem
aviso prévio.
39
Motherboard Manual
POLISH
SPEC
Procesor
Chipset
Socket FM1
Architektura AMD 64 umożliwia przetwarzanie 32 i 64
AMD A-Series / E2-Series Procesory
bitowe
AMD A55
Gniazda DDR3 DIMM x 4
Moduł pamięci DDR3 z trybem podwójnego kanału
Pamięć
Maks. wielkość pamięci 32GB
główna
Każde gniazdo DIMM obsługuje moduły
512MB/1GB/2GB/4GB/8GB DDR3
ITE 8728
Super I/O
Obsługa DDR3 800/1066/1333/1600/1866
Obsługa DDR3 2000 (OC)
Funkcje kontroli warunków pracy,
Zapewnia najbardziej powszechne funkcje Monitor H/W
Super I/O.
Kontroler prędkości wentylatora
Interfejs Low Pin Count
Funkcja ITE "Smart Guardian"
Transfer danych do 3 Gb/s.
SATA II
Zintegrowany kontroler Serial ATA
Zgodność ze specyfikacją SATA w wersji 2.0
Obsługa RAID 0,1,10
10 / 100 / 1000 Mb/s z automatyczną negocjacją
LAN
RTL8111E
szybkości
Działanie w trybie połowicznego/pełnego dupleksu
Kodek
dźwiękowy
Gniazda
Złącza
wbudowane
5.1 kanałowe wyjście audio
VT1708B
Obsługa High-Definition Audio
Gniazdo PCI Express Gen2 x16
x2
Gniazdo PCI Express Gen2 x1
x2
Gniazdo PCI
x2
Złącze SATA
x6
Każde złącze obsługuje 1 urządzenie SATA
Złącze panela przedniego
x1
Obsługa elementów panela przedniego
Przednie złącze audio
x1
Obsługa funkcji audio na panelu przednim
Złącze wyjścia S/PDIF
x1
Obsługa funkcji cyfrowego wyjścia audio
Złącze główkowe wentylatora
procesora
x1
Złącze główkowe wentylatora
systemowego
40
x2
Zasilanie wentylatora procesora (z funkcją Smart Fan)
Zasilanie wentylatora systemowego
TA57A
SPEC
Złącze główkowe kasowania
CMOS
x1
Złącze USB2.0
x2
Każde złącze obsługuje 2 porty USB2.0 na panelu
przednim
Złącze Port drukarki
x1
Złącze zasilania (24 pinowe)
x1
Złącze zasilania (4 pinowe)
x1
Klawiatura PS/2
x1
Mysz PS/2
x1
Back Panel Port szeregowy
I/O
Wymiary
płyty
operacyjne
go
x1
Port LAN
x1
Port USB2.0
x4
Gniazdo audio
x3
220 mm (S) X 305 mm (W)
Obsluga
systemu
Każde złącze obsługuje 1 Port drukarki
Biostar zastrzega sobie prawo dodawania lub
Windows XP / Vista / 7
odwoływania obsługi dowolnego systemu
operacyjnego bez powiadomienia.
41
Motherboard Manual
RUSSIAN
СПЕЦ
CPU
(центральн Гнездо FM1
Архитектура AMD 64 разрешать обработка
ый
данных на 32 и 64 бит
Процессоры AMD A-Series / E2-Series
процессор)
Набор
микросхем
AMD A55
Слоты DDR3 DIMM x 4
Основная
Максимальная ёмкость памяти 32ГБ
память
Каждый модуль DIMM поддерживает
512МБ/1ГБ/2ГБ/4ГБ/8ГБ DDR3
Super I/O
Модуль памяти с двухканальным режимом DDR3
Поддержка DDR3 800/1066/1333/1600/1866
Поддержка DDR3 2000 (OC)
ITE 8728
Инициативы по охране окружающей среды,
Обеспечивает наиболее используемые
Аппаратный монитор
действующие функциональные
Регулятор скорости
возможности Super I/O.
Функция ITE "Smart Guardian"
Интерфейс с низким количеством выводов (Интеллектуальная защита)
SATA II
Локальная
сеть
Встроенное последовательное устройство
управления ATA
скорость передачи данных до 3 гигабит/с.
Соответствие спецификации SATA версия 2.0
Поддержка RAID 0,1,10
Автоматическое согласование 10 / 100 / 1000
RTL8111E
Мб/с
Частичная / полная дуплексная способность
Звуковой
кодек
Слоты
Звуковая поддержка High-Definition
VT1708B
5.1канальный звуковой выход
Слот PCI Express Gen2 x16
x2
Слот PCI Express Gen2 x1
x2
Слот PCI
x2
Встроенны Разъём SATA
x6
Каждый разъём поддерживает 1 устройство SATA
й разъём
Разъём на лицевой панели
x1
Поддержка устройств на лицевой панели
Входной звуковой разъём
x1
Разъём вывода для S/PDIF
x1
Контактирующее приспособление
вентилятора центрального процессора x1
42
Поддержка звуковых функций на лицевой
панели
Поддержка вывода цифровой звуковой функции
Источник питания для вентилятора центрального
процессора (с функцией интеллектуального
вентилятора)
TA57A
СПЕЦ
Контактирующее приспособление
вентилятора системы
x2
Источник питания для вентилятора системы
Открытое контактирующее
приспособление CMOS
x1
USB2.0-разъём
x2
Разъём Порт подключения
Задняя
Каждый разъём поддерживает 2 USB2.0-порта на
лицевой панели
Каждый разъём поддерживает 1 Порт
принтера
x1
Разъем питания (24 вывод)
x1
Разъем питания (4 вывод)
x1
Клавиатура PS/2
x1
Мышь PS/2
x1
Последовательный порт
x1
подключения принтера
панель
средств
ввода-выв Порт LAN
ода
Размер
панели
Поддержка
OS
x1
USB2.0-порт
x4
наушников
x3
220 мм (Ш) X 305 мм (В)
Biostar сохраняет за собой право добавлять или
Windows XP / Vista / 7
удалять средства обеспечения для OS с или без
предварительного уведомления.
43
‫‪Motherboard Manual‬‬
‫‪ARABIC‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫‪FM1‬ﻡﻘﺒﺲ‬
‫اﻟﻤﺮآﺰﻳﺔ‬
‫‪AMD A-Series / E2-Series‬ﻡﻌﺎﻟﺠﺎت‬
‫ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫‪AMD A55‬‬
‫إﺝﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺏﻴﺔ ﺏﺴﺮﻋﺔ ‪ 32‬و‪ 64‬ﺏﺖ‪AMD 64‬ﺗﻤﻜﻦ ﺗﻘﻨﻴﺔ‬
‫ﻓﺘﺤﺔ ‪DDR3 DIMM‬‬
‫ﻋﺪد‪4‬‬
‫ﻡﺰدوﺝﺔ اﻟﻘﻨﺎة‪DDR3‬وﺣﺪة ذاآﺮة‬
‫ﺳﻌﺎت ‪DDR3 1866/1600/1333/1066/800‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮع‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 32‬ﺝﻴﺠﺎ ﺏﺎﻳﺖ‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫ﻡﻴﺠﺎ ‪ /512‬ﺳﻌﺔ ‪ DDR3‬ﺗﺪﻋﻢ ذاآﺮة ﻡﻦ ﻥﻮع ‪DIMM‬ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ ﻡﻴﺠﺎ ﺏﺎﻳﺖ‬
‫ﺏﺎﻳﺖ و‪ /1‬و‪ /2‬و‪ /4‬و‪ 8‬ﺝﻴﺠﺎ ﺏﺎﻳﺖ‬
‫)‪ 2000 (OC‬ﺳ ﻌﺎت ‪ DDR3‬ﻧ ﻮع ﻣﻦ اﻟﺬاآﺮة ﺗ ﺪﻋﻢ‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫‪ITE 8728‬‬
‫‪Super I/O‬‬
‫ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻡًﺎ‪Super I/O .‬ﺗﻮﻓﺮ وﻇﻴﻔﺔ‬
‫ﻡﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ‬
‫‪Low Pin Count Interface‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪ ITE‬ﻡﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬
‫ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺏﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ ‪ 3‬ﺝﻴﺠﺎﺏﺖ‪/‬ﺙﺎﻥﻴﺔ‪.‬‬
‫‪SATA II‬‬
‫‪ 2.0‬اﻹﺹﺪار‪SATA‬ﻡﻄﺎﺏﻘﺔ ﻟﻤﻮاﺹﻔﺎت‬
‫ﻡﺘﻜﺎﻡﻞ‪Serial ATA‬ﻡﺘﺤﻜﻢ‬
‫‪RAID 0,1,10‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ ‪ 100/10‬ﻣﻴﺠﺎ ﺑﺎیﺖ ‪ /‬ﺛﺎﻧﻴﺔ و‪1‬ﺝﻴﺠﺎ ﺑﺖ‪/‬ﺛﺎﻧﻴﺔ‬
‫ﺵﺒﻜﺔ داﺥﻠﻴﺔ‬
‫‪RTL8111E‬‬
‫آﻮدﻳﻚ اﻟﺼﻮت‬
‫‪VT1708B‬‬
‫إﻣﻜﺎﻧﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻣﻞ‪/‬اﻟﻨﺼﻔﻲ‬
‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮﻳﻒ ﻡﻦ‬
‫‪ 5.1‬ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‬
‫اﻟﻔﺘﺤﺎت‬
‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬
‫اﻟﻠﻮﺣﺔ‬
‫ﻓﺘﺤﺔ ‪PCI Express Gen2 x16‬‬
‫ﻋﺪد ‪2‬‬
‫ﻓﺘﺤﺔ ‪PCI Express Gen2 x1‬‬
‫ﻋﺪد ‪2‬‬
‫ﻓﺘﺤﺔ ‪PCI‬‬
‫ﻋﺪد ‪2‬‬
‫ﻡﻨﻔﺬ ‪SATA‬‬
‫ﻋﺪد‪6‬‬
‫‪SATA‬ﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺣﺪ ﻡﻦ أﺝﻬﺰة‬
‫ﻡﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺏﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻡﻨﻔﺬ ﺥﺮج ‪S/PDIF‬‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ‬
‫وﺹﻠﺔ ﻡﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫ﻋﺪد ‪1‬‬
‫‪Smart Fan‬ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻡﻊ وﻇﻴﻔﺔ‬
‫‪44‬‬
‫‪TA57A‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫ﻡﻨﺎﻓﺬ دﺥﻞ‪/‬ﺥﺮج‬
‫اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ‬
‫وﺹﻠﺔ ﻡﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪ‪2‬‬
‫وﺹﻠﺔ ﻡﺴﺢ ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ‪USB2.0‬‬
‫ﻋﺪد ‪2‬‬
‫ﻡﻨﻔﺬ ﻃﺎﺏﻌﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺏﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺏﺎﺏﻴﺲ(‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺣﺔ ﻡﻔﺎﺗﻴﺢ ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﺎوس ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻡﺤﻠﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﺎﻓﺬ ‪USB2.0‬‬
‫ﻋﺪد ‪4‬‬
‫ﻡﻘﺒﺲ ﺹﻮت‬
‫ﻋﺪد ‪3‬‬
‫ﺣﺠﻢ اﻟﻠﻮﺣﺔ‬
‫‪ 305‬ﻡﻢ )ﻋﺮض( ‪ 220 X‬ﻡﻢ )ارﺗﻔﺎع(‬
‫دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ‬
‫‪Windows XP / Vista / 7‬‬
‫ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫ﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲ ‪ USB2.0‬ﺏﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﺏﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺗﺸﻐﻴﻞ ﺏﺈﺥﻄﺎر أو ﺏﺪون ‪Biostar‬ﺗﺤﺘﻔﻆ‬
‫إﺥﻄﺎر‪.‬‬
‫‪45‬‬
Motherboard Manual
JAPANESE
仕様
CPU
Socket FM1
AMD 64アーキテクチャでは、32ビットと64ビット計算が
AMD A-Series / E2-Series プロセッサ
可能です
チップセット AMD A55
DDR3 DIMMスロット x 4
デュアル チャンネルモードDDR3メモリモジュール
最大メモリ容量32GB
DDR3 800/1066/1333/1600/1866 をサポート
メインメモリ
各DIMMは 512MB/1GB/2GB/4GB/8GB DDR3
DDR3 2000 (OC) をサポート
をサポート
Super I/O
ITE 8728
環境コントロールイニシアチブ、
もっとも一般に使用されるレガシーSuper I/O機
H/Wモニター
能を採用しています。
ファン速度コントローラ/ モニター
低ピンカウントインターフェイス
ITEの「スマートガーディアン」機能
最高3 Gb/秒のデータ転送速度
SATA II
SATAバージョン2.0仕様に準拠。
統合シリアルATAコントローラ
RAID 0,1,10のサポート
LAN
10 / 100 / 1000 Mb/秒のオートネゴシエーション
RTL8111E
半/全二重機能
サウンド
Codec
スロット
ハイデフィニションオーディオのサポート
VT1708B
5.1 チャンネルオーディオアウト
PCI Express Gen2 x16スロット
x2
PCI Express Gen2 x1スロット
x2
PCIスロット
x2
オンボードコ SATAコネクタ
ネクタ
46
x6
各コネクタは1つのSATAデバイスをサポートします
フロントパネルコネクタ
x1
フロントパネル機能をサポートします
フロントオーディオコネクタ
x1
フロントパネルオーディオ機能をサポートします
S/PDIFアウトコネクタ
x1
デジタルオーディオアウト機能をサポートします
CPUファンヘッダ
x1
CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ
x2
システムファン電源装置
CMOSクリアヘッダ
x1
TA57A
仕様
各コネクタは2つのフロントパネルUSB2.0ポートをサポ
USB2.0コネクタ
x2
ートします
背面パネル
I/O
プリンタポートコネクタ
x1
電源コネクタ(24ピン)
x1
電源コネクタ(4ピン)
x1
PS/2キーボード
x1
PS/2マウス
x1
シリアルポート
x1
LANポート
x1
USB2.0ポート
x4
オーディオジャック
x3
各コネクタは1つのプリンタポートをサポートします
ボードサイズ 220 mm (幅) X 305 mm (高さ)
OSサポート Windows XP / Vista / 7
Biostarは事前のサポートなしにOSサポートを追加または
削除する権利を留保します。
2011/08/01
47
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement