Biostar TPower X79 Owner's Manual

Biostar TPower X79 Owner's Manual
TPOWER X79 Set up M anu al
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction ................................................................ 1
1.1
Before You Start.............................................................................................1
1.2
Package Checklist .........................................................................................1
1.3
Motherboard Features...................................................................................2
1.4
Rear Panel Connectors...................................................................................4
1.5
Motherboard Layout .....................................................................................5
Chapter 2: Hardware Installation .................................................. 6
2.1
Installing Central Processing Unit (CPU).......................................................6
2.2
FAN Headers..................................................................................................8
2.3
Installing System Memory..............................................................................9
2.4
Connectors AND Slots...................................................................................11
Chapter 3: Headers & Jumpers Setup........................................... 14
3.1
How to Setup Jumpers..................................................................................14
3.2
Detailed Settings..........................................................................................14
Chapter 4: RAID / AHCI Functions............................................... 22
4.1
Operating System ........................................................................................22
4.2
Raid Arrays..................................................................................................23
4.3
How RAID Works .........................................................................................24
4.4
Smart Storage Caching ................................................................................28
Chapter 5: T-Power BIOS & Software........................................... 29
5.1
T-Power BIOS...............................................................................................29
5.2
T-Power Software ........................................................................................32
5.3
Extra Information........................................................................................39
5.4
AMI BIOS Beep Code....................................................................................40
5.5
AMI BIOS Post Code .....................................................................................41
5.6
Troubleshooting...........................................................................................43
Chapter 6: BIOS Update.............................................................. 44
6.1
BIOS Update Utility .....................................................................................44
6.2
Online Update Utility ..................................................................................46
6.3
BIOSTAR BIOS Flasher..................................................................................48
Appendix: SPEC In Other Languages............................................ 50
German ....................................................................................................................50
French .....................................................................................................................52
Italian .....................................................................................................................54
Spanish .....................................................................................................................56
Portuguese ...............................................................................................................58
Polish .....................................................................................................................60
Russian .....................................................................................................................62
Arabic .....................................................................................................................64
Japanese...................................................................................................................66
TPOWER X79
CHAPTER 1: INTRODUCTION
1.1
BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
„
„
„
„
„
„
1.2
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
PACKAGE CHECKLIST
Serial ATA Cable X 6
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver CD X 1
SLI Bridge X 1
CrossFireX Bridge X 1
Note: The package contents may be different due to area or your motherboard
version.
1
Motherboard Manual
1.3
MOTHERBOARD FEATURES
SPEC
Supports Execute Disable Bit / Enhanced Intel
SOCKET 2011
CPU
SpeedStep® / Intel Architecture-64 / Extended
Intel Sandybridge-E series / Core i7
Memory 64 Technology / Virtualization Technology /
Extreme / Core i7 processor
Chipset
Hyper Threading
Intel X79
IT8728
Super I/O
Environment Control initiatives,
Provides the most commonly used legacy Hardware Monitor Controller
Super I/O functionality.
Fan Speed Controller
Low Pin Count Interface
ITE's "Smart Guardian" function
DIMM Slots x 4
Quad Channel Mode DDR3 memory module
Main
Each DIMM supports 1GB / 2GB / 4GB /
Supports DDR3 2400(OC)/2133(OC)/1866(OC)/1600/
Memory
8GB DDR3
1333 /1066/800
Max Memory Capacity 32GB
Registered DIMM and ECC DIMM is not supported
SATA2 x 3 (by Intel X79)
* Data transfer rates up to 3 Gb/s.
Support RAID 0 / 1 / 5 / 10 and Intel SRT
SATA
SATA3 x 2 (by Intel X79)
* Data transfer rates up to 6 Gb/s.
SATA3 x 2 (by ASM1061)
* Data transfer rates up to 6 Gb/s.
Support RAID 0 / 1 / 5 / 10 and Intel SRT
Support AHCI
eSATA
eSATA x 1 (by Intel X79)
LAN
Realtek RTL 8111E
Sound
Codec
Slots
Data transfer rates up to 3 Gb/s.
Support RAID 0 / 1 / 5 / 10 and Intel SRT
10 / 100 Mb/s / 1Gb/s auto negotiation
Half / Full duplex capability
7.1 channels audio out
ALC898
High Definition Audio
PCI slot
x1
Supports PCI expansion cards
PCI Express Gen3 x16 slot (x16)
x2
Supports PCI-E Gen3 x16 expansion cards, Nvidia SLI
PCI Express Gen3 x16 slot (x8)
x1
PCI Express Gen2 x1 slot
x2
and AMD CrossFireX
Supports PCI-E Gen3 x16 expansion cards, Nvidia SLI
and AMD CrossFireX
2
Supports PCI-E Gen2 x1 expansion cards
TPOWER X79
SPEC
SATA3 Connector
x4
Each connector supports 1 SATA device
SATA2 Connector
x3
Each connector supports 1 SATA device
Front Panel Connector
x1
Supports front panel facilities
Front Audio Connector
x1
Supports front panel audio function
S/PDIF out Connector
x1
Supports digital audio out function
CPU Fan Header
x1
CPU Fan power supply (with Smart Fan function)
On Board
System Fan Header
x2
System Fan Power supply
Connector
Clear CMOS Header
x1
Restore CMOS data to factory default
USB3.0 Connector
x1
Each connector supports 2 front panel USB3.0 ports
USB2.0 Connector
x2
Each connector supports 2 front panel USB2.0 ports
Power Connector (24pin)
x1
Connects to Power supply
Power Connector (8pin)
x2
Connects to Power supply
Serial Port Connector
x1
Connects to RS-232 Port
Consumer IR Connector
x1
Supports infrared function
PS/2 Keyboard
x1
Connects to PS/2 Keyboard
LAN Port
x1
Connect to RJ-45 ethernet cable
USB2.0 Port
x2
Connect to USB devices
USB3.0 Port
x6
Connect to USB devices
Audio Jack
x6
Provide Audio-In/Out and microphone connection
eSATA Port
x1
Connect to SATA devices
Optical +coaxial S/PDIF Out
x1
Provides digital audio out function
Back Panel
I/O
Board Size
244 (W) x 305 (L) mm
OS Support Windows XP / Vista / 7
ATX
Biostar Reserves the right to add or remove support for
any OS with or without notice
3
Motherboard Manual
1.4
REAR PANEL CONNECTORS
PS/2
Keyboard
S/PDIF Out
RCA
LAN
eSATA
USB2.0X2
USB3.0X2
Center
4
USB3.0X2
USB3.0X2
Line In
Rear
Line Out
Side
Mic In
TPOWER X79
1.5
MOTHERBOARD LAYOUT
USB_KBMS1
ATXP WR2
ATXP WR3
SPDIF1
CPU 1
DDR3_C1
Socket 2011
DDR3_D1
DUA LUSB_
ESATA1
DDR3_ B1
DDR3_ A1
USB 3_0
RJ45USB1
AUDIO2
J1
ATXPWR1
CPU_FAN1
SYS _FAN2
S ATA1
PEX16_1
Super
I/O
BAT1
Intel
X79
PEX1_2
SATA4
PEX1_1
SATA3
SATA2
LA N
PEX16_2
BIOS
PCI1
CODEC
PEX16_3
CL_CMOS_
JSPDIF_OUT1
F_AUDIOF1
JFRONT_USB3_1
J_COM1
CIR1
F_USB1
F_US B2
M E_RECOVERY1
BTN1
JCMOS1
PANEL1
SYS_FAN1
RSTSW1 PWRSW1
Note: ■ represents the 1st pin.
5
Motherboard Manual
CHAPTER 2: HARDWARE INSTALLATION
2.1
INSTALLING CENTRAL PROCESSING UNIT (CPU)
Step 1: Locate and identify the locking lever, UNLOCK 1 LIFT and LOCK
1 LIFT.
UNLOCK 1 LIFT
LOCK 1 LIFT
Step 2: First, pull the locking lever UNLOCK 1 LIFT out from the socket;
next, pull the LOCK 1 LIFT out from the socket.
1
2
6
TPOWER X79
Step 3: Pushing down the hook of left locking lever to lift the load plate,
and then remove the Protection Cap.
2
1
Step 4: Locate the triangular cut edge on the socket, and hold the CPU
firmly, orientating the golden dot on the CPU forwards to this
socket triangular cut edge. The CPU will fit only in the correct
orientation.
Special Notice:
After the CPU installation, please make good preservation of the
Protection Cap for future use. When the CPU is removed, cover the
Protection Cap on the empty socket to ensure pin legs won’t be
damaged.
Step 5: Reversely, lower the locking lever LOCK 1 LIFT to locked position,
next the UNLOCK 1 LIFT to locked position, and then complete
the installation.
2
1
7
Motherboard Manual
Step 6 Put the CPU Fan and heatsink assembly on the CPU and buckle it
on the retention frame. Connect the CPU FAN power cable into
the CPU_FAN1 to complete the installation.
2.2
FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
CPU_FAN1: CPU Fan Header
Pin
1
2
3
1
4
4
Assignment
Ground
+12V
FAN RPM rate
sense
Smart Fan
Control
SYS_FAN1: NorthBridge Fan Header
SYS_FAN2: System Fan Header
S YS _FAN2
1
Pin
1
2
3
3
Assignment
Ground
+12V
FAN RPM rate
sense
S YS _FAN1
1
3
Note:
The SYSFAN1/SYSFAN2 support 3-pin head connectors, and the CPU_FAN1, 4-pin
head connector. When connecting with wires onto connectors, please note that the red
wire is the positive and should be connected to pin#2, and the black wire is Ground and
should be connected to GND.
8
TPOWER X79
2.3
INSTALLING SYSTEM MEMORY
DD R3_C1
DD R3_A1
DD R3_B1
A. Memory Modules
1.
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2.
Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
9
Motherboard Manual
B. Memory Capacity
10
DIMM Socket
Location
DDR3 Module
DDR3_A1
512MB/1GB/2GB/4GB/8GB
DDR3_B1
512MB/1GB/2GB/4GB/8GB
DDR3_C1
512MB/1GB/2GB/4GB/8GB
DDR3_D1
512MB/1GB/2GB/4GB/8GB
Total Memory
Size
Max is 32GB.
TPOWER X79
2.4
CONNECTORS AND SLOTS
SATA1~SATA4: Serial ATA Connectors
This motherboard provides several SATA controllers for connecting to SATA
devices with respective spec and transfer rates as bellows:
CONNECTOR
BY CHIP
SPEED
Support
SATA1/SATA2-U/SATA2-L
Intel X79
3 Gb/s.
RAID 0 / 1 / 5 / 10 and Intel SRT
SATA3-U/SATA3-L
Intel X79
6 Gb/s.
RAID 0 / 1 / 5 / 10 and Intel SRT
SATA4-U/SATA4-L
ASM1061
6 Gb/s.
AHCI
SATA1
SATA4-U
SATA4- L
(By ASM1061)
SATA3-U SATA2- U
SATA3- L SATA2- L
(By Intel X79)
11
Motherboard Manual
PCI1: Peripheral Component Interconnect Slot
This motherboard is equipped with 1 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI1
PEX1_1: PCI-Express Gen2 x2 Slots
-
PCI-Express 2.0 compliant.
Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.
PEX1_1
PEX1_2
12
TPOWER X79
PEX16_1 & PEX16_2: PCI-Express Gen3 x16 (x16) (Nvidia SLI and
AMD CrossFireX) Slots
PEX16_3: PCI-Express Gen3 x16 (x8) (Nvidia SLI and AMD
CrossFireX) Slot
Slot
PEX16_1 /
PEX16_2
PEX16_3
PCIe
Bandwidth
Bandwidth
Architecture
Per Direction
Total
X 16
PCI-Express 3.0
16GB
32GB
X8
PCI-Express 3.0
8GB
16GB
Speed
Note:
For more details about Nvidia SLI and AMD CrossFireX, please access the
website, respectively: http://www.nvidia.com/page/support.html, and
http://support.amd.com/us/Pages/AMDSupportHub.aspx .
PEX16_1
PEX16 _2
PEX16_3
13
Motherboard Manual
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1
HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened
3.2
Pin closed
Pin1-2 closed
DETAILED SETTINGS
JPANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.
PWR_LED
On/ Off
+ + -
9
1
16
8
+ SPK
RST
HLED
Pin
1
2
3
4
5
6
7
8
14
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Function
Speaker
Connector
Hard drive
LED
Reset button
Pin
9
10
11
12
13
14
15
16
Assignment
N/A
N/A
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Function
N/A
N/A
Power LED
Power-on button
TPOWER X79
ATXPWR1 (12V1): ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply. (Note: +12V Current Limit > 12A)
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Assignment
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
12
24
1
13
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Assignment
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V
ATXPWR2~3 (12V2): ATX Power Source Connectors
These connectors provide +12V to CPU power circuit. (Note: +12V Current
Limit > 17A ~ 21A)
4
1
5
8
Pin
1
2
3
4
5
6
7
8
Assignment
+12V
+12V
+12V
+12V
Ground
Ground
Ground
Ground
Note:
Plug in either ATXPWR2 or ATXPWR3 connector to power on the system. It is
recommended that both ATXPWR2 and ATXPWR3 connectors should be plugged in
when overclocking.
If the CPU power plug is 4-pin, please plug it into Pin 1-2-5-6 of ATXPWR2/3.
15
Motherboard Manual
J1: Auxiliary Power for Graphics
This connector is an auxiliary power connection for graphics cards. Exclusive
power for the graphics card provides better graphics performance.
Pin
1
2
3
4
4
Assignment
+12V
Ground
Ground
VCC
1
F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel
Theses headers allow user to connect additional USB cable on the PC front
panel. They also can be connected with internal USB devices, like USB card
reader.
F_USB 1 F_ USB2
16
2
10
1
9
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
Key
NC
TPOWER X79
JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
VBUS0
SSRX1SSRX1+
Ground
SSTX1SSTX1+
Ground
D1D1+
ID
1
10
20
11
Pin
11
12
13
14
15
16
17
18
19
20
Assignment
D2+
D2Ground
SSTX2+
SSTX2Ground
SSRX2+
SSRX2VBUS1
Key
17
Motherboard Manual
F_AUDIOF1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header supports HD and AC’97 audio front panel connector.
Pin
1
2
3
4
5
6
7
8
9
10
HD Audio
Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense
2
10
1
9
Pin
1
2
3
4
5
6
7
8
9
10
AC’97
Assignment
Mic In
Ground
Mic Power
Audio Power
RT Line Out
RT Line Out
Reserved
Key
LFT Line Out
LFT Line Out
Note: It is recommended that you connect a high-definition front panel audio module to
this connector to avail of the motherboard's high definition audio capability.
18
TPOWER X79
JSPDIFOUT1: Digital Audio-out Connectors
The JSPDIFOUT1 is for connecting the PCI bracket SPDIF output.
Pin
1
2
3
Assignment
+5V
SPDIF_OUT
Ground
JSPDIFOUT1
1
3
On-Board Buttons
There are 3 on-board buttons.
CL_CMOS_BTN1
PWRSW1
RSTSW1
PWRSW1:
This is an on-board Power Switch button.
RSTSW1:
This is an on-board Reset button.
CL_CMOS_BTN1: Clear CMOS Header
You can use this jumper to reset the BIOS to default.
19
Motherboard Manual
JCMOS1: Clear CMOS Header
Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.
1
3
Pin 1-2 Close:
Normal Operation (default).
1
1
3
3
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1.
2.
3.
4.
5.
6.
Remove AC power line.
Set the jumper to “Pin 2-3 close”.
Wait for five seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
Reset your desired password or clear the CMOS data.
J_COM1: Serial Port Connector
The motherboard has a Serial Port Connector for connecting RS-232 Port.
20
2
10
1
9
Pin
Assignment
1
2
3
4
5
6
7
8
9
10
Carrier detect
Received data
Transmitted data
Data terminal ready
Signal ground
Data set ready
Request to send
Clear to send
Ring indicator
NC
TPOWER X79
CIR1: Consumer IR Connector
This header is for infrared remote control and communication.
2 6
Pin
1
2
3
4
5
6
Assignment
IrDA serial input
Ground
Ground
Key
IrDA serial output
IR Power
1 5
BIOS POST Code/CPU Temperature Indicator
This indicator will show POST code while booting; after the booting sequence, it
will show current CPU temperature. Please refer to Chapter 5.5 for all the
BIOS POST codes.
21
Motherboard Manual
CHAPTER 4: RAID / AHCI FUNCTIONS
4.1
OPERATING SYSTEM
SATA
CHIP
Controller
OS
Configuration
Intel X79 RSTe
AHCI
SATA1/SATA2-U/
SATA2-L/SATA3-U/
Windows XP SP2 (64bit)
Windows Vista SP2 (32 and 64 bit)
Windows 7 (32 and 64 bit)
SATA3-L/eSATA
Intel X79 RSTe
RAID
SATA1/SATA2-U/
SATA2-L/SATA3-U/
SATA3-L/
Windows XP SP2 (64bit)
Windows 7 (32 and 64 bit)
eSATA
ASM1061
AHCI
SATA4-U/SATA4-L
Windows XP SP2 (32 and 64 bit)
Windows Vista SP2 (32 and 64 bit)
Windows 7 (32 and 64 bit)
The 'F6 Method'+ to enable RAID / AHCI Driver when installing Windows XP
1.
Before you start Windows installation, copy the proper files for the Windows
version to any USB storage ( Windows XP 64 only could use a USB floppy drive)
Windows XP 32
Windows XP 64
SATA1/SATA2-U/
SATA2-L/SATA3-U/
SATA3-L/
eSATA AHCI/RAID
Driver Path
No Support
x:\Driver\Chipset\Intel\SATA\
X79\F6flpy64\Driver\
SATA4-U/SATA4-L
AHCI Driver Path
x:\Driver\\SATA\
Asmedia_F6\Xp\
Driver\
x:\Driver\\SATA\Asmedia_F6\
Xp\Driver\
2. When the operating system installation starts, follow Windows indication by
pressing F6 to load the driver.
22
TPOWER X79
Enable RAID / AHCI Driver when installing Windows 7/Vista
1.
Before you start Windows installation, copy the proper files for the Windows
version to any USB storage.
Windows 7 32
Windows 7 64
Windows Vista 32
Windows Vista 64
SATA1/
SATA2-U/
SATA2-L/
SATA3-U/
SATA3-L/
eSATA
AHCI/RAID
Driver Path
x:\Driver\Chipset\
Intel\SATA\X79\F6fl
py32\Driver\
x:\Driver\Chipset\
Intel\SATA\X79\F6fl
py64\Driver\
x:\Driver\Chipset\
Intel\SATA\X79\F6fl
py32\Driver\
x:\Driver\Chipset\
Intel\SATA\X79\F6fl
py64\Driver\
SATA4-U/
SATA4-L AHCI
Driver Path
x:\Driver\\SATA\
Asmedia_F6\Win7\
Driver\x86\
x:\Driver\\SATA\
Asmedia_F6\Win7\
Driver\x64
x:\Driver\SATA\
Asmedia_F6\Vista\
Driver\x86\
x:\Driver\SATA\
Asmedia_F6\Vista\
Driver\x64\
2. Follow Window 7 / Vista indication to load the driver in the installation process.
4.2
RAID ARRAYS
CONNECTOR
BY CHIP
SPEED
Support
SATA1/SATA2-U/SATA2-L/
Intel X79
3 Gb/s.
RAID 0 / 1 / 5 / 10 and Intel SRT
Intel X79
6 Gb/s.
RAID 0 / 1 / 5 / 10 and Intel SRT
eSATA
SATA3-U/SATA3-L
RAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write
times for many applications.
RAID 1: RAID 1 defines techniques for mirroring data.
RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1.
RAID 5: RAID 5 provides fault tolerance and better utilization of disk capacity.
23
Motherboard Manual
4.3
HOW RAID WORKS
RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It
breaks up a large file into smaller blocks and performs disk reads and writes
across multiple drives in parallel. The size of each block is determined by the
stripe size parameter, which you set during the creation of the RAID set based on
the system environment. This technique reduces overall disk access time and
offers high bandwidth.
Features and Benefits
­
­
­
­
­
Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the
platform.
Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.
Benefits: provides increased data throughput, especially for large files. No
capacity loss penalty for parity.
Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.
Fault Tolerance: No.
Block 1
Block 3
Block 5
24
Block 2
Block 4
Block 6
TPOWER X79
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a
RAID 1 array system. The mirrored (backup) copy of the data can reside on the
same disk or on a second redundant drive in the array. RAID 1 provides a
hot-standby copy of data if the active volume or drive is corrupted or becomes
unavailable because of a hardware failure.
RAID techniques can be applied for high-availability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive and
less reliable media.
Features and Benefits
­
­
­
­
­
Drives: Minimum 2, and maximum is 2.
Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
Fault Tolerance: Yes.
Block 1
Block 2
Block 3
Block 1
Block 2
Block 3
25
Motherboard Manual
RAID 10:
RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 10
solution for improved resiliency, performance and rebuild performance.
Features and Benefits
­
­
­
­
Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID levels
in an array, and allows for spare disks.
Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
Fault Tolerance: Yes.
Block 1
Block 3
Block 5
26
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
Block 2
Block 4
Block 6
TPOWER X79
RAID 5:
RAID 5 stripes both data and parity information across three or more drives. It
writes data and parity blocks across all the drives in the array. Fault tolerance is
maintained by ensuring that the parity information for any given block of data is
placed on a different drive from those used to store the data itself.
Features and Benefits
­
­
­
­
­
Drives: Minimum 3.
Uses: RAID 5 is recommended for transaction processing and general
purpose service.
Benefits: An ideal combination of good performance, good fault tolerance,
and high capacity and storage efficiency.
Drawbacks: Individual block data transfer rate same as a single disk. Write
performance can be CPU intensive.
Fault Tolerance: Yes.
Disk 1
DATA 1
DATA 3
PARITY
DATA 7
DATA 9
PARITY
Disk 2
DATA 2
PARITY
DATA 5
DATA 8
PARITY
DATA 11
Disk 3
PARITY
DATA 4
DATA 6
PARITY
DATA 10
DATA 12
27
Motherboard Manual
4.4
SMART STORAGE CACHING
With Intel(R) Rapid Storage Technology, the performance of RAID with an Intel SSD
drive can be improved better.
Installing Smart Sotrage Caching
1.
Install RAID drives (RAID 0, 1, 5) and an Intel SSD.
2.
Activate RAID mode from BIOS, and install operating system.
3.
Insert the Setup CD to the optical drive, and Install all drivers (including Intel(R)
Rapid Storage Technology Driver). After all processes finish, reboot the system.
4.
Intel(R) RST service icon will show in notification area. Double click it to open the
main windows.
5.
Select “Accelerate” page, and make sure the status of accelerated device has
been enabled accelerated.
28
TPOWER X79
CHAPTER 5: T-POWER BIOS & SOFTWARE
5.1
T-POWER BIOS
T-Power BIOS Features
Overclocking Navigator Engine (O.N.E.)
Self Recovery System (S.R.S)
Smart Fan Function
BIO-Flasher: Update UEFI BIOS file from USB Flash Drive
!! WARNING !!
For better system performance, the UEFI BIOS firmware is being
continuously updated. The UEFI BIOS information described below
in this manual is for your reference only and the actual UEFI BIOS
information and settings on board may be different from this
manual. For further information of setting up the UEFI BIOS,
please refer to the UEFI BIOS Manual in the Setup CD.
A. Overclocking Navigator Engine (O.N.E.)
O.N.E provides several systems allowing users to customize personal
overclock settings, such as Manual Voltage System, Manual Memory
System, Manual MCT System, and Manual G.P.U System, etc.
Notice:
Not all types of Intel CPU perform above overclock setting ideally; the difference will be based on the
selected CPU model.
29
Motherboard Manual
NOTE
Overclock is an optional process, but not a “must-do” process; it is not
recommended for inexperienced users. Therefore, we will not be responsible
for any hardware damage which may be caused by overclocking. We also
would not guarantee any overclocking performance.
B. Self Recovery System (S.R.S.)
This function can’t be seen under UEFI BIOS setup, and is always on whenever
the system starts up.
However, it can prevent system hang-up due to inappropriate overclock
actions.
When the system hangs up, S.R.S. will automatically log in the default UEFI
BIOS setting, and all overclock settings will be re-configured.
C. Smart Fan Function
Smart Fan Function is under “Smart Fan Control” in “Advanced Menu”.
This is a brilliant feature to control CPU/System Temperature vs. Fan speed.
When enabling Smart Fan function, Fan speed is controlled automatically by
CPU/System temperature.
This function will protect CPU/System from overheat problem and maintain the
system temperature at a safe level.
↓
30
TPOWER X79
CPU Smart FAN
This item allows you to control the CPU Smart Fan function.
CPU FAN Calibrate
Press [ENTER] to calibrate CPU FAN.
Control Mode
This item provides several operation modes of the fan.
Fan Ctrl OFF(℃)
When CPU temperature is lower than this value, the CPU fan will keep
lowest RPM. The range is from 0~127, with an interval of 1.
Fan Ctrl On(℃)
When CPU temperature is higher than this value, the CPU fan controller
will turn on. The range is from 0~127, with an interval of 1.
Fan Ctrl Start Value
This item sets CPU FAN Start Speed Value. The range is from 0~127, with
an interval of 1.
Fan Ctrl Sensitive
The bigger the numeral is, the higher the FAN speed is. The range is from
0~127, with an interval of 1.
31
Motherboard Manual
5.2
T-POWER SOFTWARE
Installing T-Power Software
1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Auto-run function has been enabled.
2. Select Software Installation, and then click on the respective software
title.
3. Follow the on-screen instructions to complete the installation.
Launching T-Power Software
After the installation process is completed, you will see the software icon
showing on the desktop. Double-click the icon to launch it.
TOverclocker
TOverclocker presents a simple Windows-based system performance
enhancement and manageability utility. It features several powerful and easy
to use tools such as Overclocking for enhancing system performance, also for
special enhancement on CPU and Memory. Smart-Fan management and PC
health are for monitoring system status.This utility also allows you to make
overclocking profiles saving unlimitedly, and pre-set OC modes are for easy
OC. (The illustration below is for reference only)
32
TPOWER X79
The CPU tab provides information on the CPU and motherboard.
The Memory tab provides information on the memory module(s).
You can select memory module on a specific slot to see its information.
The OC Tweaker tab allows you to change system clock settings and voltages
settings. It also provides six pre-set modes for you:
33
Motherboard Manual
Six Pre-set Modes: V3, V6, V9, V12, V15, AUTO for different overclocking
experience.
The HW Monitor tab allows you to monitor hardware voltage, fan speed, and
temperature. Besides, you also can set related values for CPU Smart Fan.
34
TPOWER X79
Pressing TOVERCLOCKER logo
will display information about
manufacturer and software version.
You can update currnet version by
clicking the button “Live Update.”
Green Power II Utility
BIOSTAR G.P.U II (Green Power Utility) is a new function. The utility enhances
energy efficiency by disabling extra phases while CPU is on light loading; it
features 4+1 power phases, current power saving, and toal power saving. This
tool integrates a friendly GUI to monitor your CPU Usage, CPU Watt, and CPU
Temperature. Moreover, it optimizes power saving and best power efficiency
on your system. (The illustration below is for reference only)
Typical Mode
Display manufacturer &
software version information
Performance
Mode
Medium Mode
Maxi-Energy Mode
Auto P hase Mode
Reset Time &
Consumption
Display CPU
information
35
Motherboard Manual
G.P.U Mode Setting
This utility provides five modes, upon your requirements, to improve
system performance or to save power consumption.
Note: Even if the modes saving more power consumption are chosen, the
system still can keep excellent performance.
36
„
Auto Phase Mode
System switches the mode automatically according to current system
loading condition.
„
Performance Mode
This is the mode saving power consumption most. Least energy will
be used in the system.
„
Typical Mode
Compared with that in Performance Mode, energy consumption in this
mode is a little bit more.
„
Medium Mode
This is the standard system power saving mode.
„
Maxi-Energy Mode
This is the best system performance mode.
TPOWER X79
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.
Before you use this utility, please set Outlook Express as your default e-mail client application program.
represents important
*informa
ti on that you
must provide. Wi thout
this information, you may
not be able to send out
the mail.
This bl ock will show
the i nformation which
would be collected in
the mail .
conditi on
*Describe
of your system.
your area or
*Select
the area cl ose to you.
Provide the e-ma il
address that you would
like to send the copy to.
e the name of
*Provid
the memory module
manufacturer.
Provide the name of
the power suppl y
manufacturer and the
model no.
Send the mail out.
Exi t thi s dialog.
Save these in forma tion to a .txt file
37
Motherboard Manual
After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.
If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.
Enter the file name and then click
“Save”. Your system information
will be saved to a .txt file.
Open the saved .txt file, you will
see your system information
including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in
the sent mail.
We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.
If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web
http://www.biostar.com.tw/app/en/about/contact.php for getting our
contact information.
38
TPOWER X79
BIOS Update Utility
BIOS Update Utility is a convenient utility which allows you to update your
motherboard BIOS under Windows system. Please refer to the detailed
instructions in the section 6.1 BIOS Update Utility of Chapter 6.
5.3
EXTRA INFORMATION
CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
39
Motherboard Manual
5.4
AMI BIOS BEEP CODE
Boot Block Beep Codes
Number of Beeps
1
2
3
4
5
7
10
11
12
13
Description
No media present. (Insert diskette in floppy drive A:)
“AMIBOOT.ROM” file not found in root directory of diskette in
A:
Insert next diskette if multiple diskettes are used for recovery
Flash Programming successful
File read error
No Flash EPROM detected
Flash Erase error
Flash Program error
“AMIBOOT.ROM” file size error
BIOS ROM image mismatch (file layout does not match
image present in flash device)
POST BIOS Beep Codes
Number of Beeps
1
3
6
7
8
Description
Memory refresh timer error
Base memory read/write test error
Keyboard controller BAT command failed
General exception error (processor exception interrupt error)
Display memory error (system video adapter)
Troubleshooting POST BIOS Beep Codes
Number of Beeps
1, 3
6, 7
8
40
Troubleshooting Action
Reseat the memory, or replace with known good modules.
Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.
z If beep codes are generated when all other expansion
cards are absent, consult your system manufacturer’s
technical support.
z If beep codes are not generated when all other expansion
cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.
If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.
TPOWER X79
5.5
AMI BIOS POST CODE
Checkpoint
03
04
05
06
07
08
C0
C1
C2
C5
C6
C7
0A
0B
0C
0E
13
20
24
2A
2C
2E
31
33
Description
Disable NMI, Parity, video for EGA, and DMA controllers. Initialize BIOS,
POST, Runtime data area. Also initialize BIOS modules on POST entry and
GPNV area. Initialized CMOS as mentioned in the Kernel Variable
"wCMOSFlags."
Check CMOS diagnostic byte to determine if battery power is OK and
CMOS checksum is OK. Verify CMOS checksum manually by reading
storage area. If the CMOS checksum is bad, update CMOS with power-on
default values and clear passwords. Initialize status register A.
Initializes data variables that are based on CMOS setup questions.
Initializes both the 8259 compatible PICs in the system
Initializes the interrupt controlling hardware (generally PIC) and interrupt
vector table.
Do R/W test to CH-2 count reg. Initialize CH-0 as system timer. Install the
POSTINT1Ch handler. Enable IRQ-0 in PIC for system timer interrupt.
Traps INT1Ch vector to "POSTINT1ChHandlerBlock."
Fixes CPU POST interface calling pointer.
Initializes the CPU. The BAT test is being done on KBC. Program the
keyboard controller command byte is being done after Auto detection of
KB/MS using AMI KB-5.
Early CPU Init Start -- Disable Cache – Init Local APIC.
Set up boot strap processor Information.
Set up boot strap processor for POST.
Enumerate and set up application processors.
Re-enable cache for boot strap processor.
Early CPU Init Exit.
Initializes the 8042 compatible Key Board Controller.
Detects the presence of PS/2 mouse.
Detects the presence of Keyboard in KBC port.
Testing and initialization of different Input Devices. Also, update the Kernel
Variables.
Traps the INT09h vector, so that the POST INT09h handler gets control for
IRQ1. Uncompress all available language, BIOS logo, and Silent logo
modules.
Early POST initialization of chipset registers.
Relocate System Management Interrupt vector for all CPU in the system.
Uncompress and initialize any platform specific BIOS modules. GPNV is
initialized at this checkpoint.
Initializes different devices through DIM.
See DIM Code Checkpoints section of document for more information.
Initializes different devices. Detects and initializes the video adapter
installed in the system that have optional ROMs.
Initializes all the output devices.
Allocate memory for ADM module and uncompress it. Give control to ADM
module for initialization. Initialize language and font modules for ADM.
Activate ADM module.
Initializes the silent boot module. Set the window for displaying text
information.
41
Motherboard Manual
Checkpoint
37
38
39
3A
3B
3C
40
52
60
75
78
7C
84
85
87
8C
8D
8E
90
A1
A2
A4
A7
A9
AA
AB
AC
B1
00
42
Description
Displaying sign-on message, CPU information, setup key message, and any
OEM specific information.
Initializes different devices through DIM. See DIM Code Checkpoints section
of document for more information. USB controllers are initialized at this
point.
Initializes DMAC-1 & DMAC-2.
Initialize RTC date/time.
Test for total memory installed in the system. Also, Check for DEL or ESC
keys to limit memory test. Display total memory in the system.
Mid POST initialization of chipset registers.
Detect different devices (Parallel ports, serial ports, and coprocessor in
CPU, etc.) successfully installed in the system and update the BDA,
EBDA…etc.
Updates CMOS memory size from memory found in memory test. Allocates
memory for Extended BIOS Data Area from base memory. Programming the
memory hole or any kind of implementation that needs an adjustment in
system RAM size if needed.
Initializes NUM-LOCK status and programs the KBD typematic rate.
Initialize Int-13 and prepare for IPL detection.
Initializes IPL devices controlled by BIOS and option ROMs.
Generate and write contents of ESCD in NVRam.
Log errors encountered during POST.
Display errors to the user and gets the user response for error.
Execute BIOS setup if needed / requested. Check boot password if installed.
Late POST initialization of chipset registers.
Build ACPI tables (if ACPI is supported).
Program the peripheral parameters. Enable/Disable NMI as selected.
Initialization of system management interrupt by invoking all handlers.
Please note this checkpoint comes right after checkpoint 20h.
Clean-up work needed before booting to OS.
Takes care of runtime image preparation for different BIOS modules. Fill the
free area in F000h segment with 0FFh. Initializes the Microsoft IRQ Routing
Table. Prepares the runtime language module. Disables the system
configuration display if needed.
Initialize runtime language module. Display boot option popup menu.
Displays the system configuration screen if enabled. Initialize the CPU’s
before boot, which includes the programming of the MTRR’s.
Wait for user input at config display if needed.
Uninstall POST INT1Ch vector and INT09h vector.
Prepare BBS for Int 19 boot. Init MP tables.
End of POST initialization of chipset registers. De-initializes the ADM
module.
Save system context for ACPI. Prepare CPU for OS boot including final
MTRR values.
Passes control to OS Loader (typically INT19h).
TPOWER X79
5.6
TROUBLESHOOTING
Probable
1.
2.
Solution
There is no power in the system. 1.
Power LED does not shine; the
fan of the power supply does not 2.
work
3.
Indicator light on keyboard does
not shine.
System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.
System does not boot from a hard disk
drive, but can be booted from optical
drive.
Make sure power cable is
securely plugged in.
Replace cable.
Contact technical support.
Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.
1.
Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from an optical
1.
Back up data and applications
drive. Hard disks can be read,
files.
applications can be used, but system 2.
Reformat the hard drive.
fails to boot from a hard disk.
Re-install applications and data
using backup disks.
Screen message shows “Invalid
Review system’s equipment. Make sure
Configuration” or “CMOS Failure.”
correct information is in setup.
System cannot boot after user installs a 1.
Set master/slave jumpers
second hard drive.
correctly.
2.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
43
Motherboard Manual
CHAPTER 6: BIOS UPDATE
There are three ways to update the BIOS: BIOS Update Utility, BIOS Online
Update Utility and BIOSTAR BIOS Flasher.
6.1
BIOS UPDATE UTILITY
1.
Installing BIOS Update Utility from the CD Driver.
2.
Download the proper BIOS from www.biostar.com.tw .
3. Open BIOS Update Utility and click
the Update BIOS button on the main
screen.
4. A warning message will show up to
request your agreement to start the
BIOS update. Click Yes to start the
update procedure.
5. Choose the location for your BIOS
file in the system. Please select the
proper BIOS file, and then click on
Open. It will take several minutes,
please be patient.
44
TPOWER X79
6. After the BIOS Update process is
finished, click on OK to reboot the
system.
7. While the system boots up and the full screen logo shows up, please press the
<Delete> key to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore
Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.
All the information and content above about the software are subject to be changed
without notice. For better performance, the software is being continuously updated.
The information and pictures described above are for your reference only. The actual
information and settings on board may be slightly different from this manual.
<Backup BIOS>
Click the Backup BIOS button on the
main screen for the backup of BIOS,
and select a proper location for your
backup BIOS file in the system, and
click Save.
45
Motherboard Manual
6.2
ONLINE UPDATE UTILITY
1. Installing BIOS Update Utility from the CD Driver.
2. Please make sure the system is connected to the internet before using
this function.
3. Open BIOS Update Utility and click the
Online Update button on the main screen.
4. An open dialog will show up to
request your agreement to start the
BIOS update. Click Yes to start the
online update procedure.
5. If there is a new BIOS version, the
utility will ask you to download it. Click
Yes to proceed.
6. After the download is completed,
you will be asked to program
(update) the BIOS or not. Click Yes
to proceed.
46
TPOWER X79
7. After the updating process is finished,
you will be asked you to reboot the
system. Click OK to reboot.
8. While the system boots up and the full screen logo shows up, press
<Delete> key to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore
Defaults function to load Optimized Defaults, and select Save Changes and Reset
to restart the computer. Then, the BIOS Update is completed.
All the information and content above about the T-Series software are subject to be
changed without notice. For better performance, the software is being continuously
updated. The information and pictures described above are for your reference only.
The actual information and settings on board may be slightly different from this manual.
47
Motherboard Manual
6.3
BIOSTAR BIOS FLASHER
BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and
simple way to update your BIOS via USB pen drive.
The BIOSTAR BIOS Flasher is built in the BIOS ROM. To enter the utility,
press <F12> during the Power-On Self Tests (POST) procedure while
booting up.
Updating BIOS with BIOSTAR BIOS Flasher
1. Go to the website to download the latest BIOS file for the motherboard.
2. Then, copy and save the BIOS file into a USB flash (pen) drive.
3. Insert the USB pen drive that contains the BIOS file to the USB port.
4. Power on or reset the computer and then press <F12> during the POST
process.
5. After entering the POST
screen, the BIOS-FLASHER
utility pops out. Choose [fs0]
to search for the BIOS file.
48
TPOWER X79
6. Select the proper BIOS
file, and a message asking if
you are sure to flash the
BIOS file. Click Yes to start
updating BIOS.
7. A dialog pops out after
BIOS flash is completed,
asking you to restart the
system. Press the [Y] key to
restart system.
8. While the system boots up and the full screen logo shows up, press
<Delete> key to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the
Restore Defaults function to load Optimized Defaults, and select Save
Changes and Reset to restart the computer. Then, the BIOS Update is
completed.
z
z
This utility only allows storage device with FAT32/16 format and single
partition.
Shutting down or resetting the system while updating the BIOS will lead to
system boot failure.
49
Motherboard Manual
APPENDIX: SPEC IN OTHER LANGUAGES
GERMAN
Spezifikationen
Unterstützt Execute Disable Bit / Enhanced Intel
SOCKET 2011
CPU
SpeedStep® / Intel Architecture-64 / Extended
Intel Sandybridge-E series /
Core i7 Extreme / Core i7 Prozessoren
Chipsatz
Hyper Threading
Intel X79
IT8728
Super E/A
Memory 64 Technology / Virtualization Technology /
Umgebungskontrolle,
Bietet die häufig verwendeten alten Super Hardware-Überwachung
E/A-Funktionen.
Lüfterdrehzahl-Controller/-Überwachung
Low Pin Count-Schnittstelle
"Smart Guardian"-Funktion von ITE
Quad Kanal DDR3 Speichermodul
DDR3 DIMM-Steckplätze x 4
Unterstützt DDR3
Arbeitsspeich Jeder DIMM unterstützt 1GB / 2GB / 4GB / 2400(OC)/2133(OC)/1866(OC)/1600/ 1333
er
8GB DDR3.
/1066/800
Max. 32GB Arbeitsspeicher
registrierte DIMMs. ECC DIMMs werden nicht
unterstützt.
SATA2 x 3 (by Intel X79)
* Datentransferrate bis zu 3Gb/s
Unterstützt RAID 0 / 1 / 5 / 10 & Intel SRT
SATA
SATA3 x 2 (by Intel X79)
* Datentransferrate bis zu 6Gb/s
Unterstützt RAID 0 / 1 / 5 / 10 & Intel SRT
SATA3 x 2 (by ASM1061)
* Datentransferrate bis zu 6Gb/s
Unterstützt ACHI
eSATA
eSATA x 1 (by Intel X79)
LAN
Realtek RTL 8111E
Datentransferrate bis zu 3Gb/s
Unterstützt RAID 0 / 1 / 5 / 10 & Intel SRT
10 / 100 / 1000 Mb/s Auto-Negotiation
Halb-/ Vollduplex-Funktion
HD
Unterstützt High-Definition Audio
Audio-Unters ALC898
7.1-Kanal-Audioausgabe
tützung
PCI-Steckplatz
x1
PCI Express Gen3 x16 Steckplatz
(x16)
Steckplätze
x2
PCI Express Gen3 x16 Steckplatz
(x8)
x1
PCI Express Gen2 x1 Steckplatz
x2
50
TPOWER X79
Spezifikationen
SATA3-Anschluss
x4
Jeder Anschluss unterstützt 1 SATA-Laufwerk
SATA2-Anschluss
x3
Jeder Anschluss unterstützt 1 SATA-Laufwerk
Fronttafelanschluss
x1
Unterstützt die Fronttafelfunktionen
Front-Audioanschluss
x1
Unterstützt die Fronttafel-Audioanschlussfunktion
S/PDIF Ausgangsanschluss
x1
Unterstützt die digitale Audioausgabefunktion
CPU-Lüfter-Sockel
x1
CPU-Lüfterstromversorgungsanschluss (mit Smart
System-Lüfter-Sockel
x2
"CMOS löschen"-Sockel
x1
USB3.0-Anschluss
x1
USB2.0-Anschluss
x2
Stromanschluss (24-polig)
x1
Stromanschluss (8-polig)
x2
Serieller Anschluss
x1
Verbraucher-IR Anschluss
x1
PS/2-Tastatur
x1
LAN-Anschluss
x1
USB2.0-Anschluss
x2
Fan-Funktion)
Onboard-Ans
chluss
System-Lüfter-Stromversorgungsanschluss
Jeder Anschluss unterstützt 2
Fronttafel-USB3.0-Anschlüsse
Jeder Anschluss unterstützt 2
Fronttafel-USB2.0-Anschlüsse
Rückseiten-E
/A
USB3.0-Anschluss
x6
Audioanschluss
x6
eSATA Anschluss
x1
Optisches +coaxial S/PDIF heraus
x1
Platinengröße 244 mm (B) X 305 mm (L)
OS-Unterstüt
zung
ATX
Biostar behält sich das Recht vor, ohne Ankündigung
Windows XP / Vista / 7
die Unterstützung für ein Betriebssystem
hinzuzufügen oder zu entfernen.
51
Motherboard Manual
FRENCH
SPEC
Prend en charge les technologies d'exécution de bit de
SOCKET 2011
UC
Processeurs Intel Sandybridge-E series /
Core i7 Extreme / Core i7
Chipset
Super E/S
désactivation / Intel SpeedStep® optimisée/
d'architecture Intel 64 / de mémoire étendue 64 / de
virtualisation / Hyper Threading
Intel X79
IT8728
Initiatives de contrôle environnementales,
Fournit la fonctionnalité de Super E/S
Moniteur de matériel
patrimoniales la plus utilisée.
Contrôleur /moniteur de vitesse de ventilateur
Interface à faible compte de broches
Fonction "Gardien intelligent" de l'ITE
Module de mémoire DDR3 à mode à quad voie
Prend en charge la DDR3
Fentes DDR3 DIMM x 4
Mémoire
Chaque DIMM prend en charge des DDR3 2400(OC)/2133(OC)/1866(OC)/1600/ 1333
principale
de 1Go / 2Go / 4Go / 8Go
/1066/800
Capacité mémoire maximale de 35Go
Les DIMM à registres et DIMM avec code correcteurs
d'erreurs ne sont pas prises en charge
* Taux de transfert jusqu'à 3 Go/s.
SATA2 x 3 (by Intel X79)
Prise en charge RAID 0 / 1 / 5 / 10 & Intel SRT
SATA
SATA3 x 2 (by Intel X79)
* Taux de transfert jusqu'à 6 Go/s.
SATA3 x 2 (by ASM1061)
* Taux de transfert jusqu'à 6 Go/s.
Prise en charge RAID 0 / 1 / 5 / 10 & Intel SRT
Prise en charge AHCI
Taux de transfert jusqu'à 3 Go/s.
eSATA
eSATA x 1 (by Intel X79)
Prise en charge Port-Miltiplier/ RAID 0 / 1 / 5 / 10 &
Intel SRT
LAN
10 / 100 / 1000 Mb/s négociation automatique
Realtek RTL 8111E
Half / Full duplex capability
Prise en
charge
Prise en charge de l'audio haute définition
ALC898
Sortie audio à 7.1 voies
audio HD
Fente PCI
x1
Fente PCI Express Gen3 x16
(x16)
Fentes
x2
Fente PCI Express Gen3 x16
(x8)
x1
Fente PCI Express Gen2 x1
x2
52
TPOWER X79
SPEC
Connecteur SATA3
x4
Connecteur SATA2
x3
Connecteur du panneau avant
x1
Prend en charge les équipements du panneau avant
Connecteur Audio du panneau avant x1
Prend en charge la fonction audio du panneau avant
Connecteur de sortie S/PDIF
x1
Prend en charge la fonction de sortie audio numérique
Embase de ventilateur UC
x1
Alimentation électrique du ventilateur UC (avec
Embase de ventilateur système
x2
Chaque connecteur prend en charge 1 périphérique
SATA
Chaque connecteur prend en charge 1 périphérique
SATA
fonction de ventilateur intelligent)
Connecteur Embase d'effacement CMOS
x1
embarqué
Connecteur USB3.0
x1
Connecteur USB2.0
x2
Connecteur d'alimentation
x1
Alimentation électrique du ventilateur système
Chaque connecteur prend en charge 2 ports USB3.0 de
panneau avant
Chaque connecteur prend en charge 2 ports USB2.0 de
panneau avant
(24 broches)
Connecteur d'alimentation
x2
(8 broches)
Connecteur de Port série
x1
Connecteur de IR du consommateur
x1
Clavier PS/2
x1
Port LAN
x1
E/S du
Port USB2.0
x2
panneau
Port USB3.0
x6
arrière
Fiche audio
x6
Port eSATA
x1
+coaxial optique sortie S/PDIF
x1
Dimensions
de la carte
244 mm (l) X 305 mm (H)
Support SE Windows XP / Vista / 7
ATX
Biostar se réserve le droit d'ajouter ou de supprimer le
support de SE avec ou sans préavis.
53
Motherboard Manual
ITALIAN
SPECIFICA
Supporto di Execute Disable Bit / Enhanced
SOCKET 2011
CPU
Processore Intel Sandybridge-E series
/
Core i7 Extreme / Core i7
Chipset
Tecnologia Extended Memory 64 / Tecnologia
Virtualization / Hyper Threading
Intel X79
IT8728
Super I/O
Intel SpeedStep® / Architettura Intel 64 /
Funzioni di controllo dell’ambiente:
Fornisce le funzionalità legacy Super I/O Monitoraggio hardware
usate più comunemente.
Controller / Monitoraggio velocità ventolina
Interfaccia LPC (Low Pin Count)
Funzione "Smart Guardian" di ITE
Modulo di memoria DDR3 a canale quad
Alloggi DIMM DDR3 x 4
Memoria
Ciascun DIMM supporta DDR3 1GB /
principale
2GB / 4GB / 8GB
Capacità massima della memoria 32GB
SATA2 x 3 (by Intel X79)
Supporto di DDR3 2400(OC)/ 2133(OC)/
1866(OC)/1600/ 1333 /1066/800
DIMM registrati e DIMM ECC non sono
supportati
* Velocità di trasferimento dei dati fino a
3Gb/s, Supporto RAID 0 / 1 / 5 / 10 & Intel SRT
SATA3 x 2 (by Intel X79)
* Velocità di trasferimento dei dati fino a
SATA
6Gb/s, Supporto RAID 0 / 1 / 5 / 10 & Intel SRT
SATA3 x 2 (by ASM1061)
* Velocità di trasferimento dei dati fino a 6
Gb/s, Supporto AHCI
Velocità di trasferimento dei dati fino a 3 Gb/s.
eSATA
eSATA x 1 (by Intel X79)
Supporto Port-Miltiplier RAID 0 / 1 / 5 / 10 &
Intel SRT
LAN
Supporto
audio HD
Negoziazione automatica 10 / 100 / 1000 Mb/s
Realtek RTL 8111E
Capacità Half / Full Duplex
Supporto audio High-Definition (HD)
ALC898
Alloggio PCI
Uscita audio 7.1 canali
x1
Alloggio PCI Express Gen3 x16
(x16)
Alloggi
x2
Alloggio PCI Express Gen3 x16
(x8)
x1
Alloggio PCI Express Gen2 x1
x2
54
TPOWER X79
SPECIFICA
Connettore SATA3
x4
Ciascun connettore supporta 1 unità SATA
Connettore SATA2
x3
Ciascun connettore supporta 1 unità SATA
Connettore pannello frontale
x1
Supporta i servizi del pannello frontale
Connettore audio frontale
x1
Supporta la funzione audio pannello frontale
Connettore output SPDIF
x1
Supporta la funzione d’output audio digitale
Collettore ventolina CPU
x1
Alimentazione ventolina CPU (con funzione
Collettore ventolina sistema
x2
Collettore cancellaz ione CMOS
x1
Connettore USB3.0
x1
Connettore USB2.0
x2
Connettore alimentazione
x1
Smart Fan)
Connettori
su scheda
Alimentazione ventolina di sistema
Ciascun connettore supporta 2 porte USB3.0
pannello frontale
Ciascun connettore supporta 2 porte USB2.0
pannello frontale
(24 pin)
Connettore alimentazione
x2
(8 pin)
Connettore Porta seriale
x1
Connettore IR del consumatore
x1
Tastiera PS/2
x1
Porta LAN
x1
I/O
Porta USB2.0
x2
pannello
Porta USB3.0
posteriore Connettore audio
Dimension
i scheda
Porta eSATA
x1
+coaxial ottico S/PDIF fuori
x1
244 mm (larghezza) x 305 mm
(altezza)
Sistemi
operativi
supportati
x6
x6
ATX
Biostar si riserva il diritto di aggiungere o
Windows XP / Vista / 7
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
55
Motherboard Manual
SPANISH
Especificación
Admite Bit de deshabilitación de ejecución / Intel
SOCKET 2011
CPU
Procesador Intel Sandybridge-E series /
Core i7 Extreme / Core i7
Conjunto de
chips
Tecnología Extended Memory 64 / Tecnología de
virtualización / Hyper Threading
Intel X79
IT8728
Súper E/S
SpeedStep® Mejorado / Intel Architecture-64 /
Iniciativas de control de entorno,
Le ofrece las funcionalidades heredadas de Monitor hardware
uso más común Súper E/S.
Controlador/monitor de velocidad de ventilador
Interfaz de cuenta Low Pin
Función "Guardia inteligente" de ITE
Módulo de memoria DDR3 de canal Quad
Ranuras DIMM DDR3 x 4
Memoria
Cada DIMM admite DDR de 1GB / 2GB /
principal
4GB / 8GB
Capacidad máxima de memoria de 32GB
SATA2 x 3 (by Intel X79)
Admite DDR3 de 2400(OC)/2133(OC)/1866(OC)/
1600/ 1333 /1066/800
No admite DIMM registrados o DIMM compatibles con
ECC
*Tasas de transferencia de hasta 3 Gb/s.
Admite RAID 0 / 1 / 5 / 10 & Intel SRT
SATA
SATA3 x 2 (by Intel X79)
*Tasas de transferencia de hasta 6 Gb/s.
Admite RAID 0 / 1 / 5 / 10 & Intel SRT
SATA3 x 2 (by ASM1061)
*Tasas de transferencia de hasta 6 Gb/s.
Admite AHCI
eSATA
eSATA x 1 (by Intel X79)
Red Local
Realtek RTL 8111E
Soporte de
sonido HD
Tasas de transferencia de hasta 3 Gb/s.
Admite Port-Multiplier/RAID 0 / 1 / 5 / 10 & Intel SRT
Negociación de 10 / 100 / 1000 Mb/s
Funciones Half / Full dúplex
Soporte de sonido de Alta Definición
ALC898
Ranura PCI
Salida de sonido de 7.1 canales
X1
Ranura PCI Express Gen3 x16
(x16)
Ranuras
X2
Ranura PCI Express Gen3 x16
(x8)
X1
Ranura PCI Express Gen2 x1
X2
Conectores Conector SATA3
X4
Cada conector soporta 1 dispositivos SATA
en placa
X3
Cada conector soporta 1 dispositivos SATA
56
Conector SATA2
TPOWER X79
Especificación
Conector de panel frontal
X1
Soporta instalaciones en el panel frontal
Conector de sonido frontal
X1
Soporta funciones de sonido en el panel frontal
Conector de salida S/PDIF
X1
Soporta función de salida de sonido digital
Cabecera de ventilador de CPU
X1
Fuente de alimentación de ventilador de CPU (con
función Smart Fan)
Cabecera de ventilador de sistema X2
Fuente de alimentación de ventilador de sistema
Cabecera de borrado de CMOS
X1
Conector USB3.0
X1
Cada conector soporta 2 puertos USB3.0 frontales
Conector USB2.0
X2
Cada conector soporta 2 puertos USB2.0 frontales
Conector de alimentación
X1
(24 patillas)
Conector de alimentación
X2
(8 patillas)
Conector Puerto serie
X1
Conector de IR del consumidor
X1
Teclado PS/2
X1
Puerto de red local
X1
Panel
Puerto USB2.0
X2
trasero de
Puerto USB3.0
X6
E/S
Conector de sonido
X6
Puerto eSATA
X1
+coaxial óptico salida S/PDIF
x1
Tamaño de
la placa
244 mm. (A) X 305 Mm. (H)
Soporte de
sistema
operativo
Windows XP / Vista / 7
ATX
Biostar se reserva el derecho de añadir o retirar el
soporte de cualquier SO con o sin aviso previo.
57
Motherboard Manual
PORTUGUESE
ESPECIFICAÇÕE
SOCKET 2011
CPU
Suporta as tecnologias Execute Disable Bit / Enhanced
Processador Intel Sandybridge-E series / Intel SpeedStep® / Intel Arquitecture -64 / Extended
Core i7 Extreme / Core i7
Chipset
Memory 64 / Virtualization / Hyper Threading
Intel X79
IT8728
Especificaçã
o Super I/O
Iniciativas para controlo do ambiente
Proporciona as funcionalidades mais
Monitorização do hardware
utilizadas em termos da especificação
Controlador/Monitor da velocidade da ventoinha
Super I/O.
Função "Smart Guardian" da ITE
Interface LPC (Low Pin Count).
Módulo de memória DDR3 de canal quad-se
Ranhuras DIMM DDR3 x 4
Suporta módulos DDR3
Memória
Cada módulo DIMM suporta uma
2400(OC)/2133(OC)/1866(OC)/1600/ 1333
principal
memória DDR3 de 1GB / 2GB / 4GB / 8GB /1066/800
Capacidade máxima de memória:32 GB
Os módulos DIMM registados e os DIMM ECC não são
suportados
SATA2 x 3 (by Intel X79)
*Velocidades de transmissão de dados até 3 Gb/s.
Suporta as funções RAID 0 / 1 / 5 / 10 & Intel SRT
SATA
SATA3 x 2 (by Intel X79)
*Velocidades de transmissão de dados até 6 Gb/s.
Suporta as funções RAID 0 / 1 / 5 / 10 & Intel SRT
SATA3 x 2 (by ASM1061)
*Velocidades de transmissão de dados até 6 Gb/s.
Suporta as funções AHCI
Velocidades de transmissão de dados até 3 Gb/s.
eSATA
eSATA x 1 (by Intel X79)
Suporta as funções Port-Multiplier/RAID 0 / 1 / 5 / 10 &
Intel SRT
LAN
Auto negociação de 10 / 100 / 1000 Mb/s
Realtek RTL 8111E
Capacidade semi/full-duplex
Suporte
para áudio
de alta
Suporta a especificação High-Definition Audio
ALC898
Saída de áudio de 7.1 canais
definição
Ranhura PCI
Ranhuras
Ranhura PCI Express Gen3 x16(x8) x1
Ranhura PCI Express Gen2 x1
58
x1
Ranhura PCI Express Gen3 x16(x16) x2
x2
TPOWER X79
ESPECIFICAÇÕE
Conector SATA3
x4
Cada conector suporta 1 dispositivo SATA
Conector SATA2
x3
Cada conector suporta 1 dispositivo SATA
Conector do painel frontal
x1
Para suporte de várias funções no painel frontal
Conector de áudio frontal
x1
Suporta a função de áudio no painel frontal
Conector de saída S/PDIF
x1
Suporta a saída de áudio digital
Conector da ventoinha da CPU
x1
Alimentação da ventoinha da CPU (com a função Smart
Conector da ventoinha do sistema
x2
Fan)
Conectores
na placa
Conector para limpeza do CMOS
x1
Conector USB3.0
x1
Alimentação da ventoinha do sistema
Cada conector suporta 2 portas USB3.0 no painel
frontal
Conector USB2.0
x2
Conector de alimentação
x1
Cada conector suporta 2 portas USB2.0 no painel
frontal
(24 pinos)
Conector de alimentação
x2
(8 pinos)
Entradas/S
aídas no
painel
traseiro
Tamanho
da placa
Conector da Porta série
x1
Conector de IR do consumidor
x1
Teclado PS/2
x1
Porta LAN
x1
Porta USB2.0
x2
Porta USB3.0
x6
Tomada de áudio
x6
Porta eSATA
x1
+coaxial ótico saída S/PDIF
x1
244 mm (L) X 305 mm (A)
Sistemas
operativos
suportados
ATX
A Biostar reserva-se o direito de adicionar ou remover
Windows XP / Vista / 7
suporte para qualquer sistema operativo com ou sem
aviso prévio.
59
Motherboard Manual
POLISH
SPEC
Obsługa Execute Disable Bit / Enhanced Intel
SOCKET 2011
Procesor
Procesor Intel Sandybridge-E series /
Core i7 Extreme / Core i7
Chipset
SpeedStep® / Intel Architecture-64 / Extended
Memory 64 Technology / Virtualization Technology /
Hyper Threading
Intel X79
Gniazda DDR3 DIMM x 4
Moduł pamięci DDR3 z trybem quad ilość kanału
Pamięć
Każde gniazdo DIMM obsługuje moduły
Obsługa DDR3 2400(OC)/2133(OC)/1866(OC)/1600/
główna
1GB / 2GB / 4GB / 8GB
1333 /1066/800
Maks. wielkość pamięci 32GB
Brak obsługi Registered DIMM oraz ECC DIMM
IT8728
Funkcje kontroli warunków pracy,
Super I/O
Zapewnia najbardziej powszechne funkcje Monitor H/W
Super I/O.
Kontroler/Monitor prędkości wentylatora
Interfejs Low Pin Count
Funkcja ITE "Smart Guardian"
SATA2 x 3 (by Intel X79)
* Transfer danych do 3 Gb/s.
Obsługa RAID 0 / 1 / 5 / 10 & Intel SRT
SATA
SATA3 x 2 (by Intel X79)
* Transfer danych do 6 Gb/s.
Obsługa RAID 0 / 1 / 5 / 10 & Intel SRT
SATA3 x 2 (by ASM1061)
* Transfer danych do 6 Gb/s.
Obsługa AHCI
eSATA
Transfer danych do 3 Gb/s.
eSATA x 1 (by Intel X79)
Obsługa Port-Multiplier/RAID 0 / 1 / 5 / 10 & Intel SRT
10 / 100 / 1000 Mb/s z automatyczną negocjacją
LAN
Realtek RTL 8111E
szybkości
Działanie w trybie połowicznego / pełnego dupleksu
Obsługa
audio HD
Obsługa High-Definition Audio
ALC898
Gniazdo PCI
7.1 kanałowe wyjście audio
x1
Gniazdo PCI Express Gen3 x16
(x16)
Gniazda
x2
Gniazdo PCI Express Gen3 x16
(x8)
x1
Gniazdo PCI Express Gen2 x1
x2
Złącza
wbudowane
60
Złącze SATA3.
x4
Każde złącze obsługuje 1 urządzenie SATA
Złącze SATA2
x3
Każde złącze obsługuje 1 urządzenie SATA
Złącze panela przedniego
x1
Obsługa elementów panela przedniego
TPOWER X79
SPEC
Przednie złącze audio
x1
Obsługa funkcji audio na panelu przednim
Złącze wyjścia S/PDIF
x1
Obsługa funkcji cyfrowego wyjścia audio
x1
Zasilanie wentylatora procesora (z funkcją Smart Fan)
x2
Zasilanie wentylatora systemowego
Złącze główkowe wentylatora
procesora
Złącze główkowe wentylatora
systemowego
Złącze główkowe kasowania CMOS x1
Złącze USB3.0
x1
Złącze USB2.0
x2
Każde złącze obsługuje 2 porty USB3.0 na panelu
przednim
Każde złącze obsługuje 2 porty USB2.0 na panelu
przednim
Back Panel
I/O
Wymiary
płyty
Złącze zasilania (24 pinowe)
x1
Złącze zasilania (8 pinowe)
x2
Złącze Port szeregowy
x1
Złącze Konsument IR
x1
Klawiatura PS/2
x1
Port LAN
x1
Port USB2.0
x2
Port USB3.0
x6
Gniazdo audio
x6
Port eSATA
x1
Optyczny +coaxial wyjścia S/PDIF
x1
244 mm (S) X 305 mm (W)
Obsluga
systemu
operacyjne
go
ATX
Biostar zastrzega sobie prawo dodawania lub
Windows XP / Vista / 7
odwoływania obsługi dowolnego systemu
operacyjnego bez powiadomienia.
61
Motherboard Manual
RUSSIAN
СПЕЦ
CPU
(центральн
ый
процессор)
Набор
микросхем
SOCKET 2011
Процессор Intel Sandybridge-E series /
Core i7 Extreme / Core i7
Поддержка технологий Execute Disable Bit /
Enhanced Intel SpeedStep® / Intel Architecture-64
/ Extended Memory 64 Technology / технологии
виртуализация / Hyper Threading
Intel X79
Модуль памяти с четырехъядерных-канал
Слоты DDR3 DIMM x 4
режимом DDR3
Основная
Каждый модуль DIMM поддерживает 1ГБ / Поддержка DDR3 2400(OC)/2133(OC)/1866(OC)/
память
2ГБ / 4 ГБ / 8 ГБ DDR3
Максимальная ёмкость памяти 32ГБ
1600/ 1333 /1066/800
Не поддерживает зарегистрированные модули
DIMM and ECC DIMM
Super I/O
IT8728
Инициативы по охране окружающей среды,
Обеспечивает наиболее используемые
Аппаратный монитор
действующие функциональные
Регулятор скорости вентилятора/ монитор
возможности Super I/O.
Функция ITE "Smart Guardian"
Интерфейс с низким количеством выводов (Интеллектуальная защита)
SATA
SATA2 x 3 (by Intel X79)
* скорость передачи данных до 3 гигабит/с.
Поддержка RAID 0 / 1 / 5 / 10 & Intel SRT
SATA3 x 2 (by Intel X79)
* скорость передачи данных до 6 гигабит/с.
Поддержка RAID 0 / 1 / 5 / 10 & Intel SRT
SATA3 x 2 (by ASM1061)
* скорость передачи данных до 6 гигабит/с.
Поддержка AHCI
eSATA
скорость передачи данных до 3 гигабит/с.
eSATA x 1 (by Intel X79)
Поддержка Port-Multiplier/RAID 0 / 1 / 5 / 10 & Intel
SRT
Локальная
сеть
Автоматическое согласование 10 / 100 / 1000
Realtek RTL 8111E
Мб/с
Частичная / полная дуплексная способность
Звуковая
поддержка
жесткого
диска
62
ALC898
Звуковая поддержка High-Definition
7.1канальный звуковой выход
TPOWER X79
СПЕЦ
Слот PCI
Слоты
x1
Слот PCI Express Gen3 x16 (x16)
x2
Слот PCI Express Gen3 x16 (x8)
x1
Слот PCI Express Gen2 x1
x2
Разъём SATA3
x4 Каждый разъём поддерживает 1 устройство SATA
Разъём SATA2
x3 Каждый разъём поддерживает 1 устройство SATA
Разъём на лицевой панели
x1 Поддержка устройств на лицевой панели
Входной звуковой разъём
x1 Поддержка звуковых функций на лицевой
Разъём вывода для S/PDIF
x1 Поддержка вывода цифровой звуковой функции
панели
Источник питания для вентилятора центрального
Контактирующее приспособление
вентилятора центрального процессора x1 процессора (с функцией интеллектуального
вентилятора)
Встроенны
й разъём
Источник питания для вентилятора системы
Контактирующее приспособление
вентилятора системы
x2
Открытое контактирующее
приспособление CMOS
x1
USB3.0-разъём
x1 Каждый разъём поддерживает 2 USB-порта на
лицевой панели
USB2.0-разъём
x2 Каждый разъём поддерживает 2 USB-порта на
лицевой панели
Разъем питания (24 вывод)
x1
Разъем питания (8 вывод)
x2
Разъём Последовательный порт
x1
Разъём едока ИКЫЙ
x1
Клавиатура PS/2
x1
Задняя
Порт LAN
x1
панель
USB2.0-порт
x2
средств
USB3.0-порт
x6
ввода-выв Гнездо для подключения наушников
x6
ода
x1
eSATA порт
Оптически +coaxial вывода для S/PDIF x1
Размер
панели
Поддержка
OS
244 мм (Ш) X 305 мм (В)
ATX
Biostar сохраняет за собой право добавлять или
Windows XP / Vista / 7
удалять средства обеспечения для OS с или без
предварительного уведомления.
63
‫‪Motherboard Manual‬‬
‫‪ARABIC‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫‪SOCKET 2011‬‬
‫وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫‪Intel Sandybridge-E series /‬ﻣﻌﺎﻟﺠﺎت‬
‫اﻟﻤﺮآﺰیﺔ‬
‫ﺑﺘﺮدد یﺼﻞ إﻟﻰ ‪Core i7 Extreme / Core i7‬‬
‫‪Execute Disable Bit / Enhanced Intel‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺎت‬
‫‪SpeedStep® / Intel Architecture-64 / Extended‬‬
‫‪Memory 64 Technology / Virtualization‬‬
‫‪Technology / Hyper Threading‬‬
‫ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ ‪Intel X79‬‬
‫ﻓﺘﺤﺔ ‪DDR3 DIMM‬‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫ﻋﺪد‪4‬‬
‫ﺳﻌﺔ ‪ DDR3‬ﺗﺪﻋﻢ ذاآﺮة ﻣﻦ ﻥﻮع ‪DIMM‬ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ‬
‫ﻏﺐ‪/8‬ﻏﺐ‪/4‬ﻏﺐ‪/2‬ﻏﺐ‪1‬‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪32‬ﺝﻴﺠﺎ ﺑﺎیﺖ‬
‫‪IT8728‬‬
‫‪Super I/O‬‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻣًﺎ‪Super I/O .‬ﺗﻮﻓﺮ وﻇﻴﻔﺔ‬
‫‪Low Pin Count Interface‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫)‪SATA2 x 3 (Intel X79‬‬
‫ذاآﺮة ‪ 3DDR‬ﻗﻨﺎة رﺑﺎﻋﻴﺔ‬
‫ﺳ ﻌﺎت ‪ DDR3‬ﻥ ﻮع ﻣﻦ اﻟﺬاآﺮة ﺗ ﺪﻋﻢ‬
‫‪2400(OC)/2133(OC)/1866(OC)/1600/ 1333‬‬
‫ﺑﺎی ﺖ ﻣﻴﺠ ﺎ ‪/1066/800‬‬
‫‪ ECC‬وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻣﻊ ‪DIMM‬ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫ﻣﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة‬
‫ﻣﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ‬
‫‪ ITE‬ﻣﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬
‫ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ ‪ 3‬ﺝﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪.‬‬
‫‪RAID 0 / 1 / 5 / 10 & Intel SRT‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪SATA‬‬
‫)‪SATA3 x 2 (Intel X79‬‬
‫ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ ‪ 6‬ﺝﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪.‬‬
‫‪RAID 0 / 1 / 5 / 10 & Intel SRT‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫)‪SATA3 x 2 (ASM1061‬‬
‫ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ ‪ 6‬ﺝﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪.‬‬
‫‪AHCI‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪eSATA‬‬
‫)‪eSATA x 1 (Intel X79‬‬
‫ﺵﺒﻜﺔ داﺥﻠﻴﺔ‬
‫‪Realtek RTL 8111E‬‬
‫دﻋﻢ اﻟﺼﻮت ﻋﺎﻟﻲ‬
‫اﻟﺘﻌﺮیﻒ‬
‫ﻓﺘﺤﺔ ‪PCI‬‬
‫)‪(x16‬ﻓﺘﺤﺔ ‪PCI Express Gen3 x16‬‬
‫اﻟﻔﺘﺤﺎت‬
‫)‪(x8‬ﻓﺘﺤﺔ ‪PCI Express Gen3 x16‬‬
‫ﻓﺘﺤﺔ ‪PCI Express Gen2 x1‬‬
‫‪ALC898‬‬
‫ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ ‪ 3‬ﺝﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪.‬‬
‫‪RAID 0 / 1 / 5 / 10 & Intel SRT‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ ‪ 100/10‬ﻣﻴﺠﺎ ﺑﺎیﺖ ‪ /‬ﺙﺎﻥﻴﺔ و‪1‬ﺝﻴﺠﺎ ﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‬
‫إﻣﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻣﻞ‪/‬اﻟﻨﺼﻔﻲ‬
‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ ﻣﻦ‬
‫‪ 7.1‬ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‬
‫ﻋﺪد ‪1‬‬
‫ﻋﺪد ‪2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻋﺪد ‪2‬‬
‫‪64‬‬
‫‪TPOWER X79‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫ﻣﻨﻔﺬ ‪SATA3‬‬
‫ﻣﻨﻔﺬ ‪SATA2‬‬
‫ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬
‫ﻣﻨﻔﺬ ﺥﺮج ‪S/PDIF‬‬
‫وﺹﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ‬
‫وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫‪SATA‬یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺝﻬﺰة‬
‫ﻋﺪد ‪4‬‬
‫ﻋﺪد ‪3‬‬
‫ﻋﺪد ‪1‬‬
‫ﻋﺪد ‪1‬‬
‫ﻋﺪد ‪1‬‬
‫ﻋﺪد ‪1‬‬
‫ﻋﺪد ‪2‬‬
‫‪SATA‬یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺝﻬﺰة‬
‫یﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫یﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ‬
‫‪Smart Fan‬ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻣﻊ وﻇﻴﻔﺔ‬
‫ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬
‫اﻟﻠﻮﺣﺔ وﺹﻠﺔ ﻣﺴﺢ ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ‪USB 3.0‬‬
‫ﻣﻨﻔﺬ ‪USB 2.0‬‬
‫ﻋﺪد ‪1‬‬
‫ﻋﺪد‪2‬‬
‫ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪8‬دﺑﻮس(‬
‫ﻋﺪد ‪2‬‬
‫ﻣﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ اﻷﺣﻤﺮ ﺗﺤ ﺖ ﻣﺴ ﺘﻬﻠﻜﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢ ‪PS/2‬‬
‫ﻣﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻣﺤﻠﻴﺔ‬
‫ﻣﻨﺎﻓﺬ ‪USB2.0‬‬
‫ﻥﺎﻓﺬ دﺥﻞ‪/‬ﺥﺮج ﻣﻨﺎﻓﺬ ‪USB3.0‬‬
‫اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ ﻣﻘﺒﺲ ﺹﻮت‬
‫ﻣﻨﻔﺬ‪eSATA‬‬
‫ﻣﺤﻮر ﻣﺘّﺤﺪ ‪+‬ﺑﺼﺮیّﺔ ﻣﻨﻔﺬ ﺥﺮج ‪S/PDIF‬‬
‫ﺣﺠﻢ اﻟﻠﻮﺣﺔ ‪ 244‬ﻣﻢ )ﻋﺮض( ‪ 305 X‬ﻣﻢ )ارﺗﻔﺎع(‬
‫دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ ‪Windows XP / Vista / 7‬‬
‫‪65‬‬
‫ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‪USB‬یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ ﻓﺘﺤﺘﻲ‬
‫ﺑﺎﻟﻠﻮﺡﺔ اﻷﻣﺎﻣﻴﺔ‪USB‬یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ ﻓﺘﺤﺘﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻋﺪد ‪1‬‬
‫ﻋﺪد ‪2‬‬
‫ﻋﺪد ‪6‬‬
‫ﻋﺪد ‪6‬‬
‫ﻋﺪد‪1‬‬
‫ﻋﺪد ‪1‬‬
‫‪ATX‬‬
‫ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺗﺸﻐﻴﻞ ﺑﺈﺥﻄﺎر ‪Biostar‬ﺗﺤﺘﻔﻆ‬
‫أو ﺑﺪون إﺥﻄﺎر‪.‬‬
Motherboard Manual
JAPANESE
仕様
Execute Disable Bit / Enhanced Intel SpeedStep® /
SOCKET 2011
CPU
Intel Architecture-64 / Extended Memory 64
Intel Sandybridge-E series /
Technology / Virtualization Technology / Hyper
Core i7 Extreme / Core i7 processor
Threadingをサポートします
チップセット Intel X79
DDR3 DIMMスロット x 4
メインメモリ
Super I/O
クワッド チャンネルモードDDR3メモリモジュール
各DIMMは 1GB / 2GB / 4GB / 8GB DDR3 DDR3 2400(OC)/2133(OC)/1866(OC)/1600/ 1333
をサポート
/1066/800 をサポート
最大メモリ容量32GB
登録済みDIMMとECC DIMMはサポートされません
IT8728
環境コントロールイニシアチブ、
もっとも一般に使用されるレガシーSuper I/O H/Wモニター
機能を採用しています。
ファン速度コントローラ/ モニター
低ピンカウントインターフェイス
ITEの「スマートガーディアン」機能
SATA2 x 3 (Intel X79)
* 最高3 Gb/秒のデータ転送速度
RAID 0 / 1 / 5 / 10 & Intel SRT のサポート
SATA3 x 2 (Intel X79)
* 最高6 Gb/秒のデータ転送速度
SATA
RAID 0 / 1 / 5 / 10 & Intel SRT のサポート
SATA3 x 2 (ASM1061)
* 最高6 Gb/秒のデータ転送速度
AHCIのサポート
eSATA
eSATA x 1 (Intel X79)
LAN
Realtek RTL 8111E
HDオーディ
オのサポート
最高3 Gb/秒のデータ転送速度
RAID 0 / 1 / 5 / 10 & Intel SRT のサポート
10 / 100 / 1000 Mb/秒のオートネゴシエーション
半/全二重機能
ハイデフィニションオーディオのサポート
ALC898
PCIスロット
7.1 チャンネルオーディオアウト
x1
PCI Express Gen3 x16スロット
(x16)
スロット
x2
PCI Express Gen3 x16スロット
(x8)
x1
PCI Express Gen2 x1スロット
x2
オンボードコ
ネクタ
66
SATA3コネクタ
x4
SATA2コネクタ
x3
各コネクタは1つのSATAデバイスをサポートします
フロントパネルコネクタ
x1
フロントパネル機能をサポートします
各コネクタは1つのSATAデバイスをサポートします
TPOWER X79
仕様
フロントオーディオコネクタ
x1
フロントパネルオーディオ機能をサポートします
S/PDIFアウトコネクタ
x1
デジタルオーディオアウト機能をサポートします
CPUファンヘッダ
x1
CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ
x2
システムファン電源装置
CMOSクリアヘッダ
x1
USB3.0コネクタ
x1
USB2.0コネクタ
x2
電源コネクタ(24ピン)
x1
電源コネクタ(8ピン)
x2
シリアルポートコネクタ
x1
消費者IRコネクタ
x1
PS/2キーボード
x1
LANポート
x1
USB2.0ポート
x2
各コネクタは2つのフロントパネルUSB3.0ポートをサポート
します
各コネクタは2つのフロントパネルUSB2.0ポートをサポート
します
背面パネル
I/O
USB3.0ポート
x6
オーディオジャック
x6
eSATAポート
x1
光学+coaxial S/PDIFアウト
x1
ボードサイズ 244 mm (幅) X 305 mm (高さ)
OSサポート Windows XP / Vista / 7
ATX
Biostarは事前のサポートなしにOSサポートを追加または削
除する権利を留保します。
2011/12/02
67
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement