USER'S

MANUAL

GENERAL INSTALLATION DIAGRAM

1

3

4

2

Sensor

1

2

3

4

Display

Control box

Control box

Sensor

A

B

C

D

A

B

C

D

Working Conditions：

1、When reverse the car, 8 sensors work at the same time. The distance from nearest obstruction and the bumper will be shown on the display with horn alarming and direction indicator.

2、When drive forward, only the front sensors work.

Three options to control the front sensors

Yellow wire of front control box

Switch

a、Control by switch:

When switch on, the front sensors start to work.

ON/ACC

b、 Control by braking :

Yellow wire of front control box Braking signal

When brake the car, the front sensors start to work ; when stop braking, the front sensors stop working in 30 second.

c、Control by both the switch and braking :

Yellow wire of front control box

Switch

Braking signal

When switch on, the front sensors start to work as above mentioned option b.

Control Switch

Horn

Sensor

D C B A

Black wire - Earth

Red wire + 12V ( ON//ACC) Yellow wire

Control box

FRONT

Control box

Display

Red wire + reversing light

Black wire - reversing light

1 2 3 4

Sensor

LCD DIGITAL DISPLAY

Front Back

Safety Area

Alarm Area

0.3-0.0m， 0.3-0.0m， Danger Area

Front Back

Safety Area

1.0-0.4m， Alarm Area

0.3-0.0m， 0.3-0.0m， Danger Area

DETECTING RANGE

Top View

Side View

70(cm) 30 0

70(cm) 30 0

DISPLAY STATUS

( Front detection )

Safety Area 60-70cm

Alarm Area 40-50cm

Danger Area 0-30cm

0 30 150(cm)

0 30 150(cm)

( Rear detection )

Safety Area 110-150cm

Alarm Area 40-100cm

Danger Area 0-30cm

SENSOR INSTALLATION DIAGRAM

90

90

Be sure no other part of vehicle falls into detecting range of sensors.

90

0.6-0.8m

0.3-0.4m

0.6-0.8m

0.3-0.4m

The best position for 2 sensors The best position for 4 sensors

The direction of sensors

Insert-in

Insert-in

Stick-on

The direction of sensors

Vertical installation position to the ground Sloping installation position to the ground

Stick-on and insert-in sensors in various shapes for options

Smooth slope Smooth round objects

Objects absorbing wave, e.g. Cotton

Objects hard to be detected

INSTALLATION TOOLS

1. Advised position to install the sensors

A. 4 drilled holes (A,B,C,D) should be under the same line.

A B C D

B. 0.5-0.8m vertically high to the ground, 0.55 is recommended.

C. Vertical, tidy surface without metal components is preferred.

2. Select drilling position for sensor A & D

A

D

A . C h o o s e s u i t a b l e d r i l l i n g position for A & D sensor with relevant mark.

B. To perform the best detecting angle, select the position for A &

D sensor with 8-13CM away f r o m t h e s i d e , 1 1 C M i s recommended, and 20° with the side.

3. Select drilling position for sensor B & C

A

4. Drilling

A

B

D

A . M e a s u r e t h e d i s t a n c e between sensor A and D, get the result "L".

B. Mark sensor B & C for every

1/3 "L" interval.

A. Drill with a small awl to locate.

5. Sensor Installation

Sensor

B. Drill with the original driller.

A.. Insert the sensors into the holes one by one and tighten them. The sensor with metal slice must be installed following the direction.

B. Hide the wires in good order according to various cars.

6. Others

Bracket 1

Fix the display on rear mirror

Bracket 2

Display is adjustable for different vision angel

Fix the display on dash board

The display should be installed where easy to be seen.

Locate the control box in the boot, keep safe, cool, dry and away from shake and interference.

7. Sensor Detecting

1.5m

H-066

H-066 Parking Sensor System consists of ultrasonic sensors, digital control box and LCD display. The system detects the distance between the car and front/rear obstruction by ultrasonic sensors installed at the front/rear bumper of car. The distance will be displayed in an innovative mode with the special designed LCD, numeric display and step-up sounds, which will be changed according to the actual positions detected obstruction so that the driver could judge the distance and avoid accident.

MAIN FEATURES

Digital LCD display

Three-stage simulation alarm

Front and back detection

Four-stage simulation distance display

"DingDingDing", "DangDangDang" alarm sound

Hidden installation

Switch, Braking delay control

Self-test function of sensor

TECHNICAL SPECIFICATIONS

Rated Voltage: DC 12V

Operating Range: DC 10-16V

Operating Current: 30-360mA

Detecting Distance: Front（0.3～0.7m） Rear（0.3～1.5m）

Ultrasonic Frequency: 40KHz

Working Temperature of Control Box: -30-+70℃

Working Temperature of Display: -20-+70℃

Display Size: 70*32*14mm

ALARM MODE

3

4

1

2

5

( Front dete ctio n )

Stage Distance

3

4

1

2

5

>0.7m

0.6~0.7m

0.4~0.5m

0.3m

<0.3m

( Rear dete ctio n )

Stage Distance

>1.5m

1.5~1.1m

1.0~0.4m

0.3m

<0.3m

Awareness

Safety Area

Safety Area

Alarm Area

Danger Area

Danger Area

Awareness

Safety Area

Safety Area

Alarm Area

Danger Area

Danger Area

Alarm Sound

Silence

Ding… …

Ding… …

Ding……

Ding……

Alarm Sound

Silence

Dang……Dang……

Dang… Dang … Dang

Dang……

Dang……

Digital Display

0.6~0.7

0.4~0.5

0.3

0.0

Digital Display

1.5~1.1

1.0~0.4

0.3

0.0

Alarm Color

White

White

White

White

Alarm Color

White

White

White

White

INSTALLATION STEPS

1. Choose right installation position for sensors

2. Select drilling position for sensor A & D （ Select drilling position for sensor 1 & 4 ）

3. Select drilling position for sensor B & C （ Select drilling position for sensor 2 & 3 ）

4. Locate the position and drill

5. Install the sensors and hide wires

6. Install the display

7. Install the control box

8. Connect the whole system according to the General Installation Diagram

INSTALLATION AND TEST

1. Adjust the directions of the sensors and axial orientation, neaten the wiring after installing the sensors.

2. Connect the power supply of back control box to the reversing light. Connect the power supply of front control box to auto ignition switch.

3. Connect the data wires between the front control box and display, and disposal the control switch with front control box. Do not disposal the sensor at the moment.

4. When the car is started, the horn sounds "Dang,Dang" to enter into working status , 2s later, it turns to standby status. Put the car into back gear, then the display shows "En"

(n=0,1,2 … )to show the number of defective sensors, with the indication of exact defective sensors. Insert one of the sensors into corresponding interface in front/back control box. Human being could be detected normally, if he stands within 0.7m right before the sensor; Pull out the sensor, and check other sensors in the same method.

Insert all the sensors in corresponding interfaces after testing.

Test: a. After connect a sensor with the control box, if the buzzer sounds"Bi …… ", please check whether there is any obstacle around it, or the sensor is fixed too tight or close to great interference sources(such as vent-pipe, wires) ;b. If the display shows any distance figure with no obstacle around the sensor, the sensor may detect the ground or some outshoots of the car(such as registration mark etc.), please check the directions of sensor and axes; c. If the system still could not work properly after the above mentioned handling, the sensor(s ) can be deemed defective, or unmatch with the control box. The system should be replaced.

Note: a. The connection between sensor and the digital control box is unique. b. It performs as: when detecting within 0.3m, it shows "0.0", instead of 0.1-0.2 to alert which requires the driver to stop immediately.

NOTE

1. The car must be in power-off, when installing ultrasonic sensors

2. Its performance may be affected in following situation: heavy rain, gravel road, bumpy road sloping road and bush, very cold, hot or moist weather, or the sensors is firned or iced over.

3. Switches among ultrasonic, electric wave, DC and AC and those among 24V, 12V voltages may also effects its performance.

4. The sensors should be installed appropriate loose or tight.

5. Its performance will be effected if the sensors are fixed on metallic bumper.

6. Avoid installing the digital control box in places of great interference, such as vent-pipe, wiring nearby.

7. Test the system to make sure it works normally before using.

8. This system is a reversing aid and the manufacturer will take no responsibility for any accidents caused after the kit is installed.