F11 User Manual

F11 User Manual
F11 User Manual
Version:1.0
Date:Jul. 2010
Introduction:
This document mainly introduces the user’s operation of F11.
About the device installation please refer to F11 Installation Guide.
F11 User Manual V1.0
Notational Conventions
This document includes such notational conventions as tips,
important notices and precautions. The notations contained in this
manual include:
: Indicates important information, including precautions, which
must be read carefully to achieve the optimal equipment performance.
2
Table of Contents
Table of Contents
1. OPERATION INSTRUCTION .......................................... 1
1.1 Finger Placement .......................................................................1
1.2 Instruction for Card Using .........................................................2
1.3 Precautions.................................................................................2
2. DEVICE INTRODUCTION ............................................ 4
2.1 Overview of Device Functions ..................................................4
2.2 Product Appearance ...................................................................5
2.3 Verification State .......................................................................7
2.4 Management Card......................................................................7
2.5 System Password .......................................................................8
2.6 Operation Timeout .....................................................................9
3. DEVICE OPERATIONS ............................................. 10
3.1 Management Card....................................................................10
3.1.1 Enroll a Management Card ...........................................10
3.1.2 Enroll an Ordinary User................................................ 11
3.1.3 Delete a Single User .....................................................17
3.2 User Verification......................................................................19
3.3 Tamper Switch .........................................................................21
4 APPENDIX ....................................................... 22
4.1 List of Parameters ....................................................................22
4.2 Statement on Human Rights and Privacy ................................23
4.3 Environment-Friendly Use Description...................................25
1. Operation Instruction
1. Operation Instruction
1.1 Finger Placement
Enroll fingerprint by pressing index finger, middle finger or ring
finger (thumb and little finger are clumsy).
1. Proper press:
Make finger center pressed
on the sensor window.
2. Improper press:
Upright
Slant
Too lean
Too low
Please adopt the correct way to place the finger to avoid
improper operation led to the identification performance degradation.
1
F11 User Manual V1.0
1.2 Instruction for Card Using
Integrated with a non-contact RF card reader module, this device
supports the ID cards and MIFARE cards (Optional and only used as ID
cards). By offering multiple verification modes such as FP verification
and RF and card verification, this device can accommodate to
diversified user needs.
Swipe your card across the sensor area following the light and beep
prompts and remove your card after the device has sensed it. For the
card sensor area, please refer to 2.2 Product Appearance.
1.3 Precautions
Protect the device from exposure to direct sunlight or strong beam,
for the strong sunlight greatly affects the fingerprint collection and leads
to fingerprint verification failure.
It is recommended to use the device under a temperature of 0–50°C
so as to achieve the optimal performance. In the event of exposure of the
device to the outdoors for long periods of time, it is recommended to
adopt sunshade and heat dissipation facilities because excessively high
or low temperature may slow down the device operation and result in
high false rejection rate (FRR) and false acceptance rate (FAR).
When installing the access control device, please connect the power
cable after all the other wiring. If the device does not operate properly,
be sure to shut down the power supply before performing necessary
inspection. Be aware that any live-line working may cause damage to
the device, and that damage is beyond the scope of our normal warranty.
2
1. Operation Instruction
For matters that are not covered in this document, please refer to
related materials including the Device Installation Guide, FP Reader
Software User Manual.
3
2. Device Introduction
2. Device Introduction
2.1 Overview of Device Functions
Our product can either control the electronic lock or connected
with external alarm. This device operation is simple and flexible, and
supports the use of management cards. With a management card, you
can perform such functions as offline enrollment, deletion of users. The
light and beep prompts will guide you through all the operations
without screen display or keyboard. Featuring a compact and simple
design, this device allows users to connect several devices through a PC
and supports several communication modes.
Door Lock
Alarm
4
2. Device Introduction
2.2 Product Appearance
Front view:
Power Button
LED Indicator
Fingerprint Sensor
Card Sensor Area
™
LED indicator: The LED indicator is used to display device
operation results and exceptional statuses which are defined as
follows:
Operation succeed: The green indicator is solid on for one second,
at the same time the speaker play one long beep.
Operation failed: The red indicator is solid on for one second, at
the same time the speaker play two short beep.
Enrollment of administrator: The red LED blinks once every
three seconds, at the same time the speaker play one long beep.
Enrollment of user: The green LED blinks twice every three
second, at the same time the speaker play two short beep every
three seconds.
Single user deletion: The red LED blinks twice every three
seconds, at the same time the speaker play two short beep.
5
F11 User Manual V1.0
Verification state: The green LED blinks once every two second,
the beeper with no sound.
™
Card Sensor Area: Refers to the area in the white dashed-line
round as shown in the figure above.
™
Fingerprint Sensor: Used to enroll and match fingerprints and
delete user.
™
Power Button: Press and hold the power button for three seconds
to turn the power off, press and hold the power button one second
to turn it on.
Bottom view:
Speaker
Reset Button
™
Reset Button: Used to restart the device.
™
Speaker: Used to play the beep sound, for details please refer to
LED Indicator introduction.
Rear view:
6
2. Device Introduction
Wiring Terminal
Tamper Switch
™
Wiring Terminal: Connects with locks and power supply through
cables. For details, please refer to F11 Installation Guide.
™
Tamper Switch: Used to generate a tamper alarm. For details, see
3.3 Tamper Switch.
2.3 Verification State
Verification state: After the device is powered on, the device
enters the verification state if you have enrolled or successfully enrolls a
management card or in the event of timeout of any operation.
In the verification state, all users are allowed to verify their identity
and unlock the door (The administrator bearing a management card can
only unlock using his fingerprint previously enrolled). The
administrator can perform such operations as user enrollment and
deletion.
2.4 Management Card
The enrolled users are classified into administrators and ordinary
7
F11 User Manual V1.0
users.
Administrators: An administrator is allowed to perform all
operations including user enrollment and deletion (Deleting all the other
users except himself). The privileges of the device administrators are
implemented through the management cards.
Ordinary users: Ordinary users are only allowed to verify their
identity and unlock.
A management card is a card specially allocated for a super
administrator. Each device must at least enroll one management card. If
no management card is enrolled, you cannot perform any operation.
You can implement different functions by swiping a management
card for different times in a row:
By swiping the management card once, you can go into the single
user enrollment state. By swiping the management card five times in a
row, you can enter the single user deletion state.
Consecutive swipes: Consecutive swipes mean the interval
between two swipes in a row is less than 5 seconds.
The fingerprints of the user who bears a management card can only
be enrolled through FP Reader software. For details, see the FP Reader
Software User Manual.
#
Tip: Users who bear management cards can only verify their
identity and unlock using their fingerprints previously enrolled.
2.5 System Password
A system password is a password used to enhance the security of
device data in TCP/IP, RS485/RS232 communications.
8
2. Device Introduction
#
Tip: The system password can be modified through the FP
Reader Software. For details, see the FP Reader Software User
Manual.
2.6 Operation Timeout
The default operation timeout time is 15 seconds. When you enroll
a management card, enroll or delete a user, the green LED will blink
twice every three seconds, at the same time the speaker play two short
beep every three seconds if there is no operation. After three times of
indicator, the device returns to verification state automatically.
#
Tip: You can set the timeout period through the FP Reader
Software.
9
3. Device Operations
3. Device Operations
3.1 Management Card
3.1.1 Enroll a Management Card
To enroll a management card, proceed as follows:
1. The device automatically detects whether there exists a
management card.
2. If the device fails to detect the presence of a management card, it
enters the management card enrollment state. The green LED blinks
once every three seconds, at the same time the speaker play one long
beep every three seconds.
#
Tip: It is timeout after 15 seconds, and return to verification
state. After management card enrolled, you can use the FP Reader
Software to set or modify the card number.
3. Register the management card, please swipe your card near to
the card sensor area.
4. If enrollment fails, the red LED is solid on for one second, at the
same time the speaker play two short beep. The system returns to step 3,
and wait for user to swipe card.
5. If enrollment succeed, the green LED is solid on for one second,
at the same time the speaker play one long beep. And system returns to
verification state.
10
3. Device Operations
#
Tip: The system returns to the verification state if any
operation in step 3 is timeout, and only prompts you to enroll the
management card again after you restart the device again.
The management card enrollment procedure is shown below:
System power-on
Swipe a new card:
Red LED is solid on
for 1s, 1 long beep
every 3s.
Management card
exist?
Verify users: Press your
finger or swipe your card.
No beep, red LED blinks
once every 2s.
Yes
No
Enroll a
management card
No
Enroll Success
Enroll
successful:
Returns to verification
state. Green LED is solid
on for 1s, 1 long beep.
Yes
Verification state
3.1.2 Enroll an Ordinary User
The mode for you to enter the enrollment state using the
11
F11 User Manual V1.0
management card is known as the management card enrollment mode.
In this mode, you can only enroll one user every time you enter
enrollment state. When you enroll a new user, the system automatically
assigns a minimum idle ID to the user.
Each user is allowed to enroll 10 fingerprints and one ID card at
most. When the fingerprint and ID card enroll completely, or operation
timeout, or swipe the management card, the system return to verification
state.
To enroll a user, proceed as follows:
1. In the verification state, the system goes into the ordinary user
enrollment state after you swipe a management card once (In the
enrollment state, swiping a management card once will return to the
verification state). In this state, you can also enroll the fingerprint for the
old user.
2. The system will automatically assign a smallest idle ID for the
new user. The green LED blinks twice every three seconds, at the same
time the speaker play two short beep every three seconds. You can start
user enrollment. There are the following two cases:
(1) Swipe ID card first
a. When you swipe your new ID card and succeed in enrolling a
user, the green LED is solid on for one second, the speaker play one
long beep, and you can proceed to step b. If user enrollment fails, the
red LED is solid on for one second, the speaker play one long beep and
returns to the enrollment state, waiting for you to press your finger or
swipe your card.
b. The system enters the specified fingerprint enrollment state.
Press the same finger over the sensor three times following the light and
12
3. Device Operations
beep prompts (The green LED blinks twice every three seconds, and the
speaker play two short beep).
c. If fingerprint enrollment succeeds, the green LED is solid on for
one second, the speaker play one long beep, and you can continue the
proceed to step b. If fingerprint enrollment fails, the red LED is solid on
for one second, and the speaker play one long beep, and repeats step b.
d. The system automatically returns to the verification state when
both 10 fingerprints and ID card are enrolled, the management card is
swiped once or operation times out.
(2) Press finger first
a. Press the same finger over the sensor three times following the
light and beep prompts (The green LED blinks twice every three
seconds, at the same time the speaker play two short beep every three
seconds) by adopting the proper finger placement. If fingerprint
enrollment succeeds, the green LED is solid on for one second, the
speaker play one long beep and you can proceed to step b. If fingerprint
enrollment fails, the red LED is solid on for one second, the speaker
play one long beep and returns to the enrollment state, waiting for your
to press your finger or swipe your card.
b. The system enters the specified user enrollment state, continue
the proceed to step a, and waiting for you to swipe your new ID card or
press your finger.
c. The system automatically returns to the verification state when
both 10 fingerprints and ID card are enrolled, the management card is
swiped once or operation times out.
3. If you are already assigned with an ID, then there are the
following two cases for you to enroll your fingerprint(s) or card:
(1) Enroll fingerprint(s) when you have already enrolled card
a. In the state of enrollment state, after you swipe the enrolled card,
the system enter the fingerprint enrollment state. You can re-enroll this
13
F11 User Manual V1.0
user’s fingerprint,and the new fingerprint(s) will overwrite the previous
fingerprints.
b. Press the same finger over the sensor three times following the
light and beep prompts by adopting the proper finger placement. If
fingerprint enrollment succeeds, the green LED is solid on for one
second, the speaker play one long beep, and gets ready for enrollment of
next fingerprint.
c. The system automatically returns to the verification state when
both 10 fingerprints and ID card are enrolled, the management card is
swiped once or operation times out.
# Tips:
1. The fingerprint(s) enrolled in this step will overwrite all your
previously enrolled fingerprints. Please swipe the card or press the
finger one second after the light blinked.
2. In this mode, the fingerprint of the user who bears the
management card cannot be enrolled because swiping the
management card will return the system to the verification state
automatically.
(2) Enroll card and fingerprint(s) when you have already
enrolled fingerprint(s)
a. Press the finger with enrolled fingerprint three times following
the light and beep prompts. If you are identified as the same person in
each of verification attempt, the system enters the fingerprint enrollment
state.
b. The system starts to re-enroll your fingerprint and ID card (If the
card is not enrolled) when the green LED blinks twice every three
seconds, the speaker play two short beep every three seconds (One
14
3. Device Operations
second after the light blinks). Your fingerprint(s) enrolled in this step
will overwrite all your previous fingerprints.
c. If you swipe a new card or press a finger three times that is not
enrolled before and succeeds in enrollment, the green LED is solid on
for one second, the speaker play one long beep, and you can continue
enrolling new fingerprints and card.
d. The system automatically returns to the verification state when
both 10 fingerprints and ID card are enrolled, the management card is
swiped once or operation times out.
15
F11 User Manual V1.0
The flow chart is shown below:
Green LED blinks twice
every 3s, 2 short beeps
every 3s, start to enroll.
Swipe
management card
Enrollment state
Press finger or
swipe card?
No
Red LED is solid
on for 1s, 1 long
beep, enrollment
failure.
Verification state
Yes
New fingerprint
or card?
Red LED is solid on
for 1s, 1 long beep,
enrollment failure.
Yes
User enrollment
successful?
No
No
Yes
Swipe card
Press finger
Green LED is solid on
for 1s, 1 long beep,
enrollment success.
No
Card enrollment
successful?
FP enrollment successful?
No
Yes
Green LED is solid on
for 1s, 1 long beep,
enrollment success.
No
Red LED is solid on
for 1s, 1 long beep,
enrollment failure.
Enrollment is
successful
10 fingerprints
and card enrolled?
Yes
Verification state
16
3. Device Operations
3.1.3 Delete a Single User
The operation steps for single user deletion:
1. In verification state, swipe your management card for five
consecutive times to enter the single user deletion state (Swipe your
management card one more time to return to the verification state). The
red LED blinks twice every three second, the speaker play two short
beep every three seconds.
2. The user press the finger or swipe the card:
(1) Press your finger onto the sensor to delete a user:
Press one of your enrolled fingers properly onto the sensor. If the
verification succeeds, the green LED is solid on for one second, the
speaker play one long beep. Deletion is successful, and automatically
return to the deletion state. If the verification fails, the red LED is solid
on for one second, the speaker play one long beep. Deletion is failed,
and automatically return to the deletion state.
(2) Swipe your card over the reader to delete a user:
Swipe a registered card over the reader. If the verification succeeds,
the green LED is solid on for one second, the speaker play one long
beep. Deletion is successful, and automatically return to the deletion
state. If the verification fails, the red LED is solid on for one second, the
speaker play one long beep. Deletion is failed, and automatically return
to the deletion state.
3. If you swipe your management card one more time or your
operation times out, the system will return to the verification state.
#
Tip: In single user deletion mode, management card users
cannot be deleted because swiping the management card will return
the system to the verification state.
17
F11 User Manual V1.0
Single User Deletion Procedure:
No registered user.
The system returns to
verification state.
Red LED blinks twice
every 3s, 2 short beep
every 3s, start to enroll.
Red LED is solid on
for 1s,one long beep,
deletion failure.
Red LED is solid on
for 1s, one long beep,
deletion failure.
Red LED is solid on
for 1s, one long beep,
deletion success.
18
3. Device Operations
# Tip: Please be cautious to do this operation, the deleted data
can not be recovered.
3.2 User Verification
Operation steps:
1. When the device is in verification state, the green LED blink
once every two second to prompt verification.
2. Start user verification. The device supports two verifications
modes: fingerprint verification and card verification.
(1) Fingerprint verification:
Press your finger on the fingerprint sensor in a proper way. If the
verification succeeds, the green LED is solid on for one second, the
speaker play two short beep. If the verification fails, the red LED is
solid on for one second, the speaker play two short beep.
(2) Card verification:
Swipe your card over the card reader. If the verification succeeds,
the green LED is solid on for one second, the speaker play two short
beep. If the verification fails, the red LED is solid on for one second, the
speaker play two short beep.
19
F11 User Manual V1.0
The user verification procedure is show as below:
Verification
state
No beep, green
LED blinks once
every 2s, start
to verify.
Door
sensor or tamper
switch
exceptional?
Yes
Alarm
No
FP verification
Card verification
No
No
FP
verification successful?
Card verification
successful?
Yes
Red LED is solid on
for 1s, 2 short
beeps, verification
failure.
Yes
Red LED is solid on for
1s, 2 short beeps,
verification failure.
Unlock and
delay
Lock
Green LED is solid on for
1s, 2 short beeps,
verification success.
Verification state
#
Tip: the administrator bearing a management card can only
unlock using his fingerprint previously enrolled.
20
3. Device Operations
3.3 Tamper Switch
The tamper switch is pressed and held down with the rear cover.
When the device is dismantled, the tamper switch will be lifted up and
then it will send an signal to trigger an alarm.
Clear alarm: The user can clear the alarm by unlocking the door
upon successful verification.
Restore factory defaults: The factory defaults can be restored
through the tamper switch.
When the system generates an alarm for 30–60 seconds, the user
can press the tamper switch three times (Till the speaker sounds) to
restore default settings, including the device number, system password,
IP address, 485 address, and keyboard password.
#
Tip: The user information stored on device will be cleared
after the device is restored to factory defaults, please be cautious.
21
4 Appendix
4 Appendix
4.1 List of Parameters
The following table lists the basic functional parameters of the device.
Item
Power Supply
Function
Note
12V 3A
Alarm/ Door lock/ Door switch
One Wiegand output
User quantity
10000 (fingerprint and ID card)
Record capacity
100000 pieces of records
Enrollment capacity
1500 fingerprints/10000 cards
(fingerprint/ card)
Verification mode.
ID (Mifare) card, fingerprint
Communications
TCP/ IP, RS485, RS232
Speaker
Beep prompt
LED
Bi-color indication (red/ green)
22
4 Appendix
4.2 Statement on Human Rights and Privacy
Dear Customers:
Thank you for choosing the multi-biometric products designed and
manufactured by us. As a world-renowned provider of biometric
technologies and services, we pay much attention to the compliance
with the laws related to human rights and privacy in every country while
constantly performing research and development.
We hereby make the following statements:
1. All of our fingerprint recognition devices for civil use only
collect the characteristic points of fingerprints instead of the fingerprint
images, and therefore no privacy issues are involved.
2. The characteristic points of fingerprints collected by our
products cannot be used to restore the original fingerprint images, and
therefore no privacy issues are involved.
3. We, as the equipment provider, shall not be held legally
accountable, directly or indirectly, for any consequences arising due to
the use of our products.
4. For any dispute involving the human rights or privacy when
using our products, please contact your employer directly.
Our fingerprint products or development tools for police use support the
collection of the original fingerprint images. As for whether such a type
of fingerprint collection constitutes an infringement of your privacy,
please contact the government or the final equipment provider. We, as
the original equipment manufacturer, shall not be held legally
accountable for any infringement arising thereof.
23
F11 User Manual V1.0
Note: The law of the People’s Republic of China has the following
regulations regarding the personal freedom:
1. Unlawful arrest, detention or search of citizens of the People's
Republic of China is prohibited; infringement of individual privacy is
prohibited.
2. The personal dignity of citizens of the People's Republic of
China is inviolable.
3. The home of citizens of the People's Republic of China is
inviolable.
4. The freedom and privacy of correspondence of citizens of the
People's Republic of China are protected by law.
At last we stress once again that biometrics, as an advanced recognition
technology, will be applied in a lot of sectors including e-commerce,
banking, insurance and legal affairs. Every year people around the globe
suffer from great loss due to the insecurity of passwords. The fingerprint
recognition actually provides adequate protection for your identity under
a high security environment.
24
4 Appendix
4.3 Environment-Friendly Use Description
The Environment Friendly Use Period (EFUP) marked on this product
refers to the safety period of time in which the product is used under
the conditions specified in the product instructions without leakage of
noxious and harmful substances.
The EFUP of this product does not cover the consumable parts that
need to be replaced on a regular basis such as batteries and so on. The
EFUP of batteries is 5 years.
Names and Concentration of Toxic and Hazardous Substances or Elements
Toxic and Hazardous Substances or Elements
Parts Name
Pb
Hg
Cd
Cr6+
PBB
PBDE
Chip resistor
×
{
{
{
{
{
Chip capacitor
×
{
{
{
{
{
Chip inductor
×
{
{
{
{
{
Chip diode
×
{
{
{
{
{
ESD components
×
{
{
{
{
{
Buzzer
×
{
{
{
{
{
Adapter
×
{
{
{
{
{
Screws
{
{
{
×
{
{
{: Indicates that this toxic or hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in SJ/T11363-2006.
×: Indicates that this toxic or hazardous substance contained in at least one of the
homogeneous materials for this part is above the limit requirement in SJ/T11363-2006.
Note: 80% of the parts in this product are manufactured with non-hazardous
environment-friendly materials. The hazardous substances or elements contained cannot be
replaced with environment-friendly materials at present due to technical or economical
constraints.
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement