KLEEMANN M156 supercharger system Instruction manual

KLEEMANN M156 supercharger system Instruction manual

Below you will find brief information for supercharger system M156. This document provides a step by step process for installing the KLEEMANN supercharger system. The procedure includes detailed instructions for removing the original intake manifold, installing the supercharger and manifold assembly, connecting cooling and fuel lines, and routing air intake and fuel lines. The document ends with warnings that the vehicle must start and idle without issues before programming the ECU, and that air fuel ratio should be verified under all operating circumstances.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

KLEEMANN supercharger system M156 Installation Guide | Manualzz
M156 Supercharger Installation Manual
Rev 280213
Tuesday, March 19, 13
This instruction manual provides a step by step process for installing the KLEEMANN M156 supercharger system. It is recommended that you read the instruction
manual completely before starting the installation of the kit to gain an overview of the entire process. If questions arise during the installation, you are welcome to
contact us directly. We are ready to provide answers and assistance. It is essential for all involved that the installation is done correctly, the car performs
flawlessly and the customer is satisfied.
It is of the utmost importance that only KLEEMANN programs the ECU. Any other supplier, what ever they may make, should not be utilized for programming.
Using an alternative source for ECU programming will void the KLEEMANN warranty, immediately and entirely. KLEEMANN’s programming utilizes features no
other supplier utilizes, keeping all factory safe running strategies in place.
The installation will be simplified with the use of just a few specialized tools. It is recommended that you have the following tools at the ready:
Crank Pulley Wrench, MB # 112 589 00 40 00
MBZ Star Diagnosis or similar diagnostic tool (AutoLogic etc)
KLEEMANN belt alignment tool
Air Fuel Ratio tool, preferably wide band
Boost pressure gauge, 0-1 bar (0-15 psi)
Kleemann A/S
Rugmarken 27B
DK-3520 Farum
Denmark
Kleemann USA Inc.
3455 Fillmore Ridge Heights
Colorado Springs , CO 80907
USA
phone +45 70 109 109
fax +45 70 109 108
phone +1 719 473 6441
fax +1 719 578 0345
[email protected]
[email protected]
Tuesday, March 19, 13
Factory Engine Bay
The engine compartment should be in as built condition.
Make sure to remove any existing tuning software from the ECU and double
check that the OE software is the latest updated version from Mercedes Benz.
Remove any other tuning items at this time and return the car to OE (Sprint
Booster, Under Drive Pulleys, Cotton/Oil Air Filters, etc).
Run the compression test from within DAS. All cylinders should have equal
contribution, if not, remedy the issue before proceeding! No fault = proceed
with installation.
Step 1:
Remove the nose cover, inlet tubes, air filters and the Y-piece on the inlet housing.
Tuesday, March 19, 13
Step 3:
Remove all hoses and tubes. Remove the 10 bolts witch hold the manifold to the cylinder
heads. Check that the inlet manifold is completely free and lift it off the car. Temporarily cover
the intake ports with wide, easy release, tape. Set the OE manifold aside for now, you will be
removing components from it later.
Step 4:
Remove the power steering tank, its hoses, and replace the 2 bolts in the cam chain housing
Remove all 3 engine lifting brackets/eyes.
Tuesday, March 19, 13
Step 5:
Remove crank pulley/harmonic damper.
MB tool: 112 589 00 40 400
Step 6:
After removing the original crank pulley, please check the radial oil seal for damage. If
damaged, replace the seal, if serviceable, install the Kleemann crank pulley.
MB tool: 112 589 00 40 400
Bolt TQ:
Stage 1= 184 lbs/ft • 250 nm
Stage 2 = release (CCW 180º)
Stage 3 = 147 lbs/ft • 200nm
Stage 4 = CW +180º
Radial oil seal = MB A023 997 84 47
Tuesday, March 19, 13
Step 7:
Install the two Kleemann idler pulleys outboard of the OE idler pulleys along with the brace.
Stacking order, L to R = Outer to Engine shown below:
The larger washer between the outer most pulley
and the stand-off for the OE pulley have been
eliminated in SC systems produced from April
2013 onward.
Step 8:
Install the belt tensioner bracket, witch is mounted on the outboard side of the alternator. Do
not fully tighten the mounting bolts, you will align this bracket later.
Do NOT fully tighten those bolts at this step!
Tuesday, March 19, 13
Step 9:
Remove the two bolts indicated by the arrows.
Step 10:
Install the power steering oil reservoir bracket as shown.
Tuesday, March 19, 13
Step 11:
This hose is normally directed to the left. Cut the clamp and remove the hose. Install one end
of the 8mm hose from the Kleemann kit. Place the hose neatly in front of the radiator fan. Do
NOT cut the other end yet!
Step 12:
Remove clamp from hose A .Remove hose assembly B. Insert the hose from step 11 fully into
hose A, reuse the OE clamp.
B
A
Tuesday, March 19, 13
Step 13:
Install the intercooler water tank with the provided bracket as shown. W209 shown, other
chassis are similar.
Step 14:
Remove the OE cloth tape from the wiring harness at the location shown.
Tuesday, March 19, 13
Step 15:
Move the wires for the fuel pressure sensor to the rear of the engine compartment as shown.
Reapply cloth harness wrap to the harness.
Step 16:
The harness should now look like this.
Tuesday, March 19, 13
Step 17:
Remove the fuel injectors from the OE fuel rail. Check the injector o-rings, top and bottom, for
damage.Replace any damaged o-rings and set the injectors aside. Remove the fuel pressure
sensor and set it aside. Install the OE fuel rail back onto the OE manifold for safe keeping.
O-Rings:
Upper: MB 014 997 68 45
Lower: MB 016 997 77 45
Step 18:
Remove the throttle body cables from the metal bracket on the front of the OE intake
manifold.
Tuesday, March 19, 13
Step 19:
Lubricate the o-rings on both ends of the fuel injectors and install the injectors into the two
KLEEMANN fuel rails.
Step 20:
Install the the two KLEEMANN fuel rails onto the supercharger manifold assembly. The feed
ports of the rails should face the back of the manifold assembly (throttles).
From this point forward extreme caution must be used with the manifold
assembly. The fuel injectors project from the manifold ports and care should
be taken to ensure the injectors are not exposed to impacts of any kind.
Tuesday, March 19, 13
Step 21:
Remove the intake air temperature sensor from the OE manifold.
Step 22:
Remove OE MAP sensor (A) and the variable length intake runner valve (B) from the OE
manifold.
A
Tuesday, March 19, 13
B
Step 23:
Remove the intake manifold lower cover of the OE intake manifold to expose the two throttles.
Remove the two throttles from the plenum.
Step 24:
Using a razor knife, cut off the rubber grommet around the throttle wiring harness. Be
extremely careful to not damage the wiring. Wrap the wiring harness were the grommet was
with cloth tape.
Tuesday, March 19, 13
Step 25:
Install the fuel pressure sensor into the KLEEMANN fuel splitter block. Install the splitter
block on the firewall.
W204
W212
Step 26:
Place the KLEEMANN supercharger/manifold assembly on a clean work bench (use a large
cloth on the bench surface to protect the manifold finish). Place the intake air temperature
sensor into intake runner #5 as shown.
Tuesday, March 19, 13
Step 27:
Take one of the throttles (it does not matter which one) and drill a 9 mm hole in the bolt
location shown.
Step 28:
Tap the ventilation port with a 10 x 1.5 mm tap. Using the square boss to the left of the
ventilation port as a guide for straightness and height, cut the port and the square boss with a
hack saw. Remove approx 3-4mm of material from the square boss. Lightly countersink the
hole. Clean the port well with brake cleaner and a blow gun and air dry. Make sure there are
no chips or debris in any portion of the throttle. Install a 10 x 1.5 mm cap screw with Loctite
271. Do this step for BOTH throttles.
Be sure to remove 3-4 mm from the square boss on the throttles. Failure to
remove this material will cause a false air leak which can lead to fault codes,
improper mixture formulation and engine failure!
Tuesday, March 19, 13
Step 29:
Install the first throttle as shown, leave bolts slightly loose. Move the throttle blade to full
open with your fingers, check to make sure it opens and closes fully and without interference.
Tighten the bolts fully.
Note location of larger diameter bolt at approx 10 o’clock.
Step 30:
Lubricate the the o-rings (throttle side of throttle adaptor plate), then install the throttle
adaptor plate as shown. Plug in the throttle wiring harness to the first throttle. Check for
interference between the first throttle and the throttle adaptor plate- correct/adjust as
required.
Tuesday, March 19, 13
Step 31:
Drill a 9 mm hole in the second throttle body at the location shown.
Step 32:
Install the bolts in the second throttle body, hand tighten them so there is still the possibly for
the throttle body position to be adjusted on the adaptor plate.
Note location of larger diameter bolt at approx 2 o’clock.
Tuesday, March 19, 13
Step 33:
Test install the inlet housing plate, check to make sure all holes are in alignment and the
second throttle is fully seated in the plate. Carefully remove the plate and tighten the bolts on
the second throttle. Install the plate agin and check again that the plate is aligned and that
both throttles have full range of movement with no interference of any kind.
Step 34:
Install the inlet housing as shown. Plug in the second throttle and route the cable under the
inlet housing. Install the 3 plastic pipes into the fittings on the throttle adaptor.
Note cable routing and plastic pipes below:
Tuesday, March 19, 13
Step 35:
Install the elbow snap fitting for the crank breather hose, turning it inwards as shown (A).
Pace breather hose under bridge pipe as shown (B).
Step 36:
Place the supercharger assembly onto the engine, use new intake manifold gaskets. Be sure
the crank breather hose is placed in the position as shown. Install the manifold bolts.
Tuesday, March 19, 13
A
B
Step 37:
Attach the fuel lines from the splitter to the fuels rails. Reconnect all hoses and wiring
connectors.
Be careful not to mix up the left MAF sensor and the fuel pressure sensor (the
connectors are very similar) or component damage can occur!
Refer to the vacuum diagram at the back of the manual for proper hose routing.
Step 38:
Cut the tank ventilation line as shown
Tuesday, March 19, 13
Step 39:
Cut the brake booster line as shown.
Step 40:
Install the quick coupler onto the brake booster line and connect it to the 12 mm line on the
supercharger manifold assembly. The proper line/port is located under the throttles.
Tuesday, March 19, 13
Step 41:
Install the belt alignment tool onto the bracket attached to the alternator in step 8 with the
provided bolt. Align the tool so it is tangent (and touching) the supercharger drive
pulley.Tighten the two bolts on the tensioner bracket (attached to the alternator). Remove the
alignment tool.
Step 42:
Install the dynamic belt tensioner onto the tensioner bracket (alternator).
Tuesday, March 19, 13
Step 43:
Install both belts.
Refer to the belt diagrams at the back of the manual for proper belt routing.
Step 44:
Install the hoses on the KLEEMANN power steering reservoir. The original metal pipe can
often be reused if it is flipped 180º, if not, use hose from the kit. Attach the reservoir to the
bracket installed in step 10. Fill reservoir with the proper oil to “MIN HOT” level as indicated
on the dipstick.
Check clearance to the electric fan and adjust as required to provide adequate
clearance.
Tuesday, March 19, 13
Step 45:
Install the OE switchover valve for the variable length manifold runners. Attach the valve to
the wiring harness and find a suitable place for it to lay. The valve no longer has any function,
but it must be connected electrically to prevent fault codes. Loop a small section of 4 mm
hose onto the barbs to keep debris out.
Step 46:
Install the hose for the secondary air injection system as shown.
Check clearance to the supercharger pulley, adjust hose length as required.
Tuesday, March 19, 13
Step 47:
Remove the Bumper cover. Install the intercooler radiator beneath the front bumper. The
intercooler radiator should be centrally located on the bumper, brackets are screwed directly
to the underside of the bumper beam. Install the intercooler water pump on the right side. Use
the supplied brackets. Be sure to allow adequate clearance for hoses not to pinch or chafe.
Refer to the intercooler diagram at the back of the manual for proper hose
routing.
Wire the intercooler pump with the supplied relay kit to a KOEO (key on, engine
on) power source. It is imperative to use the relay kit as the pump draws high
amperage. DO NOT direct wire the intercooler pump to ANY OE system,
damage will result.
The small port on the intercooler reservoir is not used. Cap and clamp it with
the provided hardware.
Step 48:
Fill the intercooler system with a 50/50 mix of anti-freeze and water. Energize the pump to
self bleed, top up coolant as bleeding occurs.
It is recommended that a 50/50 mix of anti-freeze and water be used in the
intercooler. “Orange” ethylene glycol is preferred.
Tuesday, March 19, 13
Step 49:
In order to use the OE air box tops they must be modified. Drill out the two inboard holes of
the upper tops to 7 mm. Insert the supplied rivet-nuts and secure using a rivet gun.
Bolts will be fed from the top side of the air box, use care that the inserts are
fastened into the air boxes correctly.
Step 50:
Trim the nose panel to the scribe line as shown.
This edge will be visible to the eye when installed so use care while cutting.
Tuesday, March 19, 13
Step 51:
Mark the lower halves of the air boxes as shown. Cut on the indicated line, all the way through.
43 mm / 1.70”
43 mm
Step 52:
After the primary cross-cut, dress the air box edges with a file.
Tuesday, March 19, 13
Step 53:
Turn the lower halves of the air boxes over and remove the ribs as shown.
Step 54:
Instal the air box side edge as shown. Assemble and install the air boxes, front panel and
intake tubes.
On some models it may be required that you modify the right side intake tube
by hot forming a small pocket in the tube to clear the power steering reservoir.
Tuesday, March 19, 13
Step 55:
Completed installation.
Step 56:
Verify that the vehicle starts and idles with the OE ECU. Check all your work.
ONLY after verifying that the vehicle starts and idles without issue
should you send in the ECU for programming. Programming the
ECU first presents a variable for diagnosis of problems that will
only complicate fault finding.
Verify air fuel ratio under all operating circumstances. Contact
KLEEMANN if anything is out of specification.
Tuesday, March 19, 13
Notes:
Tuesday, March 19, 13
Vacuum Line Diagram, M156 SC
Schematic layout only, not
shown to scale or orientation.
All OE vacuum consumers must
be connected to the VAC/ATMOS
port ONLY!
The VAC/ATMOS/BOOST port is
for testing or GGE purposes ONLY!
Vacuum/Atmosphere signal:
t0&."14FOTPS
t0&"JS*OKFDUJPO4XJUDIPWFS
t0&5BOL7FOUJMBUJPO
t4$#ZQBTT7BMWF
t"OZPUIFS0&7BDVVN$POTVNFS
(varies by chassis)
SC bypass valve is connected to
the VAC/ATMOS port ONLY!
supercharger
Vacuum/Atmosphere/Boost signal:
t5FTU1PSU
t#PPTU((&
Tuesday, March 19, 13
Accesory Belt Routing Diagram, M156 SC
idler
idler
p/s
idler
w/p
tens
crank
alt
a/c
Tuesday, March 19, 13
SC Belt Routing Diagram, M156 SC
s/c
idler
idler
tens
crank
Tuesday, March 19, 13
SC Intercooler Diagram, M156 SC
Schematic layout only, not
shown to scale or orientation.
supercharger
res
radiator
pump
Tuesday, March 19, 13

advertisement

Key Features

  • Step-by-step installation guide
  • Detailed instructions for removing and installing components
  • Clear illustrations and diagrams
  • Vacuum line and belt routing diagrams
  • Intercooler installation guidance
  • Air box modification instructions
  • ECU programming recommendations
  • Air fuel ratio verification instructions

Frequently Answers and Questions

What is the purpose of this document?
This document provides a step-by-step guide for installing the KLEEMANN supercharger system on a Mercedes-Benz M156 engine.
What tools are required for the installation?
The installation requires specialized tools like a crank pulley wrench, MBZ Star Diagnosis tool, KLEEMANN belt alignment tool, air fuel ratio tool, and a boost pressure gauge.
What steps should be taken before starting the installation?
Before starting the installation, ensure the engine compartment is in as-built condition, remove any existing tuning software from the ECU, double-check that the OE software is the latest updated version, and run a compression test to ensure all cylinders have equal contribution.

Related manuals

Download PDF

advertisement