FO-HDMI-SET User Guide
AV Connectivity, Distribution And Beyond...
VIDEO WALLS VIDEO PROCESSORS
VIDEO MATRIX SWITCHES
EXTENDERS SPLITTERS WIRELESS
CABLES & ACCESSORIES
4X4 HDMI HDBASET MATRIX SWITCHER
WITH PoE/IR/RS232/Ethernet/4K
HBT-4K-C6-8X8E
Model #: SW-HBT4K-C6-4X4E
© 2013 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any
express or implied warranty, relating to its products are is strictly prohibited.
Product Application & Market Sectors
Coroprate
House Of Worship
Military
Residential
Education
Industrial
Medical
Aviation
www.avenview.com
TABLE OF CONTENTS
1.1
IMPORTANT SAFEGUARDS ................................................................................................. 3
1.2
SAFETY INSTRUCTIONS ...................................................................................................... 3
1.3
REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) ........... 4
2.
INTRODUCTION AND FEATURES..................................................................................... 5
2.1
PACKAGE CONTENTS......................................................................................................... 6
2.2
BEFORE INSTALLATION ...................................................................................................... 7
2.2
CABLE SPECIFICATIONS ..................................................................................................... 7
2.3
APPLICATION DIAGRAM ..................................................................................................... 8
3.
PANEL DESCRIPTION .....................................................................................................................9
3.1 FRONT PANEL (SW-HBT4K-C6-4X4E) .......................................................................................9
3.2 REAR PANEL (SW-HBT4K-C6-4X4E)...........................................................................................10
4.
IR REMOTE AND CABLE DEFINITION ............................................................................ 11
5.
INSTALLATION AND COMPATABLE DEVICES ............................................................. 12
6.
GENERAL TROUBLESHOOTING ...................................................................................... 13
SECTION 7: SPECIFICATIONS ....................................................................................................... 14
www.avenview.com
Page|2
SECTION 1: GETTING STARTED
1.1 IMPORTANT SAFEGUARDS
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover











Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
Removal or installation of the product.
Causes external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
Normal wear and tear.
Any other causes which does not relate to a product defect.
Removal, installation, and set-up service charges.
1.2 SAFETY INSTRUCTIONS
The SW-HBT4K-C6-4X4E HDBaseT HDMI CAT5/6/7 Matrix Switcher set has been tested for conformance
to safety regulations and requirements, and has been certified for international use. However, like all electronic
equipments, the SW-HBT4K-C6-4X4E should be used with care. Read the following safety instructions to
protect yourself from possible injury and to minimize the risk of damage to the unit.
Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to
dangerous voltage or other hazards
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid
falls or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.
www.avenview.com
Page|3
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this
equipment.
Warning symbols
Description
ONLY USE THE PROVIDED POWER CABLE
OR POWER ADAPTER SUPPLIED. DO NOT
TAMPER WITH THE ELECTRICAL PARTS.
THIS MAY RESULT IN ELECTRICAL SHOCK
OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING
SO WILL VOID THE WARRANTY AND
CONTINUED USE OF THE PRODUCT.
THE VIDEO BOARDS ARE VERY SENSITIVE
TO STATIC. PLEASE ENSURE IF RACK
MOUNTED OR INSTALLED ON A SURFACE,
IT SHOULD BE IN A GROUNDED
ENVIROMENT.
www.avenview.com
Page|4
2. INTRODUCTION
Avenview 4K 4x4 HDBaseT HDMI Matrix Switcher over CAT5e/6/7 supports the transmission of video
and multi-channel digital audio along with IR, RS-232 and LAN (Internet). This matrix can be controlled via
Telnet or Web GUI to setup 4 HD sources to any eight single CAT5e/6/7outputs (up to 100m) to any of the
eight screens to be displayed.
Video Signals: [email protected] (Ultra HD), 3D, 8/10/12 Deep Color, and Full HD [email protected] Hz/36-bit color depth.
Audio signals: LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio
Data Signals: Bi-Directional IR signals 30 KHz to 50 KHz over CAT5/6. LAN up to 100Mbps
The SW-HBT-4K-4x4E includes one (1) unit: Transmitter unit with eight (4) UTP output ports which allows
the user to extend all signals up 100m (330ft). Compatible with receivers HBT-C6POE-R and HBT-C6PLT-R
The bonus features with this device it can be powered by the 24V from the TX PoE (Power over the CATx
cable to the RX) also extends Internet (100Mbps Ethernet service when connected to a Router at the TX).
These features has been added to this unit to give the installer and user a complete solution with the new
trends in online streaming, network connected devices and new demand in Smart TV, Ultra HD monitors
and content.
FEATURES
1. INPUT: HDMI with 3D & 4Kx2K (UHD), 1080p, HDCP and DVI compliant
2. VIDEO BANDWIDTH: From 340 MHz/10.2 GBs
3. PC RESOLUTIONS: Up to VGA to WUXGA
4. HD RESOLUTIONS: Up to 4Kx2K ([email protected] and [email protected])1080p
([email protected]) AUDIO SUPPORTED: LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTSHD Master Audio AUDIO TRANSMISSION: (32-192kHz sample rate)
5. SUPPORTS: CEC bypass
6. DISTANCE: Extra 100 meters connected with HBT-C6POE-SET through CAT6e/6a/7 cables =200m
(300m with additional Repeater unit) Cascading HDBaseT Matrixes
7. ETHERNET TRANSMISSION: Rate up to 100Mbps
8. UNCOMPRESSED VIDEO: 1080p, 60 Hz, 36-bit
9. SERVICE: USB for Manufacturer USE ONLY
10. 3D SUPPORT: Follow by Display / TV’s EDID
11. 5Play™ convergence: HDMI, LAN, PoE & Bi Directional Control
NOTE:
Receivers (Rx) from different manufactures and non HDBaseT would not be compatible.
Displaying HDMI 4Kx2K resolution would require the standard 4Kx2K HDMI cable and display for accurate results. Do not connect CAT inputs/outputs
of this device to a POE network switch. Doing so may damage the unit. Only connect LAN port to a network.
www.avenview.com
Page|5
2.1
PACKAGE CONTENTS
Before you start the installation of the converter, please check the package contents.
1
1x SW-HBT4K-C6-4X4E
2
IR EXTENDER
3
IR BLASTER
4
IR REMOTE
5
1 x Power Adapter (24V/3.75A DC)
6
Power Cord
7
1 x Right and Left Ear Rack Sets
8
User’s Manual
www.avenview.com
Page|6
2.2 BEFORE INSTALLATION




Put the product in an even and stable location. If the product falls down or drops, it may cause an
injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or
high humidity.
Use the DC power adapter with correct specifications and supplied with the unit. If improper
power supply is used the unit may malfunction and cause a fire.
Do not twist or pull by force ends of the UTP cable. It can cause malfunction.
2.2 CABLE SPECIFICATIONS
To achieve best results with our SW-HBT4K-C6-4X4E we highly recommend a premium quality 26 or 24
AWG HDMI cable with the below specifications to maintain signal integrity and distances.
FEATURES:











Length: 5m (16ft) to 15m (50ft)
Bandwidth: 10.2 Gbps data transfer rate
Supports Resolution: Up to 3840x2160 @ 24Hz and 4096x2160 @ 24Hz, 1080p @ 24Hz / 50/60Hz/3D
Conductor gauge: 26 / 24 AWG
Deep Color
3D Capable
CEC
Ethernet Channel
Audio Return Channel
Connector 1: HDMI (Type A) Male
Connector 2: HDMI (Type A) Male
www.avenview.com
Page|7
2.3 APPLICATION DIAGRAM
www.avenview.com
Page|8
3. PANEL DESCRIPTION
3.1 FRONT PANEL (SW-HBT4K-C6-4X4E)
2
1
3
4
5
6
1. Front Panel Menu (FPM): Displays the
2. IR: IR Receiver window (accepts the remote
3. POWER: (LED Status) GREEN Power ON, RED
4. LOCK: Press for 3 seconds to lock all the buttons
information of the input and output settings.
Standby Mode.
control signal of this matrix only).
on the panel; press again for 3 seconds to unlock.
The LED Status Green when locked.
5. MENU: Press to access the FPM system, Easily 6. A~D/1~4 and In/Out: Press Out or In button to
manage EDID settings and quickly access the IP
info of device.
select the output or input mode and then press
the preferred number to manually setup your
solution.
www.avenview.com
Page|9
3. PANEL DESCRIPTION
3.2 REAR PANEL (SW-HBT4K-C6-4X4E)
1
2
5
3
4
6
4
5
6
5
6
5
10
6
4
7
4
9
8
1. RS-232: Connect to PC or control system with
D-Sub 9-pin cable for the transmission of RS-232
commands.
2. LAN: Connect to active network for LAN serving
and Telnet and Web GUI control (refer to Control
Codes Guide).
3. SERVICE: Manufacturer use only.
4. CAT5e/6/7 OUT 1~8: Connect from these CAT
outputs to the CAT input port of the receiver units
with a single CAT5e/6/7 cable for HDMI Audio/
Video and IR/RS-232 control signal transmission.
5. IR IN 1~4: Connect to IR extenders for IR
signal reception.
6. IR OUT 1~4: Connect to IR blasters for IR
signal transmission.
7. HDMI IN 1~4: Connect to HDMI input source.
8. DC 24V MAIN POWER: Plug the 24 V DC
power supply into the unit.
9. ALL IR IN: Connect to IR extender for IR signal
reception. Ensure that remote being used is
within the direct line-of-sight of the IR extender
for it will send out the signal to all receiver's IR
OUT.
10.ALL IR OUT: Connect to IR blaster for IR signal
transmission to source side. Place the IR blaster in
direct line-of-sight of the equipment to be controlled
for it will blaster out all signal received from the IR IN
at the receiver sides.
www.avenview.com
Page|10
4. IR REMOTE AND CABLE DEFINITION
REMOTE CONTROL
1 POWER: Press this button to
switch on the device or set it to
standby mode.
1
22 IN: Input ports selection 1~8.
33 OUT: Output ports selection A~H.
3
2
IR Blaster
1 Power 5 V
2 IR Blaster Signal
3 NC
IR Receiver
1 IR Signal
2 Power 5 V
3 Grounding
IR Sockets
IR BLASTER: plug in the IR blaster to the SW-HBT4K-C6-4X4E to emit all IR command signals received from the IR
Extender plugged into the Rx (Monitor Side) to control the devices corresponding to the IR signals.
Example: Set Top Box or DVD player (The Source).
IR EXTENDER: plug in the IR Extender into the (RX) Receiver (Monitor Side) to receive all IR command signals
from the IR remote controls of the corresponding source.
Example: Set Top Box or DVD player (IR Remote Control).
www.avenview.com
Page|11
NOTE: Incorrect placement of IR Blaster and IR Extender into the extender may result in
the failure of the IR extenders.
Please check carefully before plugging in the IR extender to the respective IR sockets.
It is clearly marked and IR 1: IR EXTENDER /IR 2: IR BLASTER
WARRANTY WILL NOT COVER THE DAMAGE
NOTE
The QUALITY and TRANSMISSION of the video signals depends on the
characteristics and quality of the UTP cables. Higher resolutions and longer
transmission distances require low skew cables (<25ns/upto 300m) for best
performance.
Unshielded CAT6 with metal RJ-45 connectors is recommended.
5. INSTALLATION (SW-HBT4K-C6-4X4E)
To setup Avenview SW-HBT4K-C6-4X4E please follow these steps for connecting to a device:
1.
2.
2.
3.
4.
5.
6.
7.
8.
Turn off all devices including monitors / TV
Connect to a HDMI source (4K or 1080p) (such as a Blu-Ray Disc player) to the matrix unit.
Connect a compatable receiver with CAT5/6/7 cable with shielded ends and HDMI out to monitor
Connect HBT-C6POE-EX to extend upto 300m with a CAT5/6/7 cable with shielded ends,
Plug in dual Power to supply the Rx with PoE
Plug in the IR BLASTER: into IR out and the blinker on the IR eye (Source)
Plug in the IR Extender to IR IN to receive IR Signals from Remote (Monitor end)
Power on the HDMI display
Power on HDMI Sources.
COMPATABLE DEVICES
HBT-C6PLT-R
Up to 60 meters
HBT-C6POE-R
Up to 100 meters
www.avenview.com
HBT-C6POE-EX
Up to 300 meters
Page|12
6. GENERAL TROUBLESHOOTING
SOLUTION
PROBLEM


NO IMAGE







EDID ISSUE


Set-Top Box
No Picture


NO Infrared
Communication


End-to-End Testing
Passive Monitoring:
Check if connection to the source and the display are correct.
Ensure that display device supports 480p, 720p and 1080p [email protected]
resolution
Terminated to 568B standard with Shielded Ends Recommended
High Quality CAT5/6/7 Cable helps signal transmission
Please use the supplied power supply-DC 24V/6.25A DC
Check LED Link light see (Section 3 Panel Description)
Check LED Sync light see (Section 3 Panel Description)
EDID MODE-TV: The default factory setting is on TV. The unit
will detect the 1st CAT5e/6/7 output’s EDID. When obtained a
(4K2K) Ultra HD 3840x2160 EDID the signal is transmitted.
If the 1st CAT5e/6/7 output is without a Ultra HD 3840x2160
EDID the unit will detect all output's EDID and Transmit the signal
that all outputs can accept.
EDID MODE-STD: Switch to STD to use built-in EDID if the
display has No Image. STD EDID's video at [email protected] and
audio at LPCM 2CH.
HDBaseT and HDMI 1.3 standards support CLOCK
STRETCHING for i2c buss protocol
Example set top boxes like Scientific Atlantic results no picture.
This can be resolved by swapping out the box for a newer version
that supports HDMI 1.3 not HDMI 1.2
Ensure the UTP cable is run within the wall away from EMI and
High Voltage power Lines.
Please check manual of device to ensure proper placement of IR
Blaster on IR EYE.
Some LED /Plasma TV have EMI interference with the IR
Extender, please place the IR Rx 3-6” away from Screen
Recommended TEST
HDBaseT system, a final end-to-end test of all the A/V components
should take place. These tests include checking the HDMI stream at
the far end (sink end), the clock rate, frame compare, video pattern,
audio, EDID and HDCP with Quantum 780 (recommended)
Passive monitoring enables an integrator to view the HDCP
transactions, EDID exchange, as well as the connection events
between the actual devices in the network.
NOTE
Addional info on Guidelines to Test & Troubleshoot HDBaseT Systems Can be retreived from our
website under the category Downloads for this product SW-HBT4K-C6-4X4E
www.avenview.com
Page|13
SECTION 7: SPECIFICATIONS
ITEM
UNITS
UNIT DESCRIPTION
HDCP
LAN / ETHERNET
VIDEO BANDWIDTH
SUPPORTED
RESOLUTIONS
AUDIO SUPPORT
HDMI IN CABLE M/M
ESD PROTECTION
INPUT
OUTPUT
HDMI CONNECTOR
IR FREQUENCY
DIMENSIONS (L X W X H)
NET WEIGHT
POWER SUPPLY
POWER CONSUMPTION
DESCRIPTION
SW-HBT4K-C6-4X4E
4K HDBaseT HDMI Matrix Switcher with IR/RS232/POE/4k2k support
YES
100Mbps
300 MHz (10.2Gbps)
[email protected]/60, [email protected], 3D
[email protected] Up to Ultra HD ([email protected]/25/30Hz)
4K2K-([email protected])
LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio
15m/[email protected] or 6m/[email protected]
Human body model — ±8kV (air-gap discharge) & ±4kV (contact discharge)
4×HDMI
5x 3.5mm Stereo jack IR Extender
1x 9pin Dsub RS-232
1x RJ45 IP Control / LAN Serving,
1x USBMini B (for firmware updates)
4x RJ45 WE/SS 8P8C with 2 LED indicators
5x 3.5mm Stereo jack IR Emitter
Type A (19 pin female)
30~50kHz
9.8” x 17.1” x 1.7”
249 mm (L)×436 mm (W)×44mm (H)
3352g /7.3lbs
24V / 3.75A DC
(US/EU standards, CE/FCC/UL certified)
66 W (PoE)
ENVIRONMENTAL
OPERATING
TEMPERATURE
STORAGE TEMPERATURE
RELATIVE HUMIDITY
32˚ ~ 104˚F (0˚ to 40˚C)
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
20~90% RH (non-condensing)
www.avenview.com
Page|14
NOTICE
1. All HDMI over UTP transmission distances are measured using Belden CAT6A (625MHz), 4-Pair, U/
UTP-Unshielded, Riser-CMR, Premise Horizontal Cable, 23 AWG Solid Bare Copper Conductors,
Polyolefin Insulation, Patented Double-H spline, Ripcord, PVC Jacket using Quantum 980 signal
HDMI Video Generator Module Video Pattern Testing.
2. The transmission length is largely affected by the type of category cables, also the type of HDMI
sources, and the type of HDMI display. The testing result shows solid UTP cables (usually in the
form of 300m or 1000ft bulk cable) can transmit a lot longer signals than stranded UTP cables
(usually in the form of patch cords). Shielded STP connectors are better suit than unshielded UTP
connectors. A solid UTP CAT5e cable shows longer transmission length than stranded STP CAT6
cable. For long extension users, solid cables are your only choice.
3. EIA/TIA-568-B termination (T568B) for category cables is recommended for better performance.
4. To reduce the interference among the unshielded twisted pairs of wires in category cable, you can
use shielded STP cables with shielded connector to improve EMI problems, which occurs in long
transmission.
5. Because the quality of the category cables has the major effects in how long transmission distance
will be made and how good is the received display, the actual transmission length is subject to your
category cables. For resolution greater than 1080i or 1280x1024, a solid CAT6 cable is the only
viable choice.
PERFORMANCE GUIDE FOR HDMI OVER CATEGORY CABLE TRANSMISSION
PERFORMANCE RATING
SHIELDING
WIRING
UNSHIELDED (UTP)
SOLID
SHIELDED (STP)
STRANDED
UNSHIELDED (UTP)
SHIELDED (STP)
TERMINATION
TYPE OF CATEGORY CABLE
CAT5e
CAT6
CAT6A/7












PLEASE USE EIA/TIA-568-B TERMINATION (T568B) AT ANY TIME
www.avenview.com
Page|16
Avenview Warranty Certificate
AVENVIEW CORP. (“Avenview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used
normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s
published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications.
LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance
and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs,
please contact [email protected]
PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if
the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact
[email protected]
To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented
to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must
be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight
charges and brokerages when shipping the product(s) to the receiver.
NOT COVERED BY THIS WARRANTY
This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including
but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire,
earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service
performed by anyone who is not a representative of Avenview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the
normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s).
AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR
CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR
ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS;
LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATION; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIRECT
OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or
exclusions may not be applicable to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
275 Woodward Avenue, Kenmore, NY 14217
1.866.508.0269
www.avenview.com
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with
respect to the operation or use of Avenview hardware, software or other products and documentation described
herein, for any act or omission of Avenview concerning such products or this documentation, for any interruption of
service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages
in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and
documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to
improve reliability, function or design. With respect to Avenview products which this document relates, Avenview
disclaims all express or implied warranties regarding such products, including but not limited to, the implied warranties
of merchantability, fitness for a particular purpose, and non-infringement.
www.avenview.com
Page|18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement