TCAM 230 network camera User Manual
The TCAM 230 is a network camera and a video and audio surveillance transmission system based on IP network through LAN, ADSL/VDSL, and Wireless LAN. This device allows you to remotely monitor video and audio from various locations.
advertisement
Network Camera
TCAM-230 User Manual
TCAM-230 User Manual
Safety Precaution
We appreciate your purchasing TCAM series. Before installing the product, please read the following with care.
°
Make sure to turn off the power before installing TCAM-230.
°
Do not install under the direct sunlight or in dusty areas.
°
Make sure to use the product within the temperature and humidity specified in the specification.
°
Do not operate the product in presence of vibrations or strong magnetic fields.
°
Do not put electrically conducting materials in the ventilation hole.
°
Do not open the top cover of the product. It may cause a failure or electric shock on the components.
°
To prevent from overheating, make sure to keep the distance at least 10cm from the ventilation hole.
°
Check for proper voltage before connecting the power.
-1-
TCAM-230 User Manual
Table of Content
Table of Content .............................................................................. 2
1. Introduction ................................................................................. 4
1. About User Manual .................................................................. 4
2. Feature .................................................................................. 4
3. Product and Accessories ......................................................... 6
4. Part Names and Functions ....................................................... 7
5. System Connections ............................................................... 8
2. Installation ................................................................................. 11
1. Connecting Network(LAN) ...................................................... 11
2. Connecting Audio ................................................................. 11
3. Connecting Serial Ports ......................................................... 11
4. Connecting Sensor and Alarm ................................................ 11
5. Connecting Power ................................................................ 11
6. Check if It Works .................................................................. 12
3. System Operation ....................................................................... 12
1.
Remote Video Monitoring .................................................... 12
2.
Initialization of IP Address ................................................... 13
4. Remote Configuration .................................................................. 14
1. Using Internet Explorer .......................................................... 14
2. TCAM-230 Configuration ....................................................... 15
2.1 System Configuration .................................................... 15
2.2 Video Configuration ....................................................... 18
2.3 Audio Configuration ....................................................... 21
2.4 Network Configuration ................................................... 23
2.5 Serial Port Configuration ................................................ 27
2.6 Event Configuration ....................................................... 29
-2-
TCAM-230 User Manual
2.7 Preset Configuration ...................................................... 33
2.8 User Configuration ........................................................ 34
2.9 Camera Configuration .................................................... 37
2.10 OSD (On Screen Display) ............................................. 38
Appendix : ALM/SEN/485 Port .......................................................... 43
-3-
TCAM-230 User Manual
1. Introduction
1. About User Manual
The User Manual is to provide information on operation of the high quality Network
Camera, TCAM-230. In this guide, information on installation, operation, configuration of
TCAM-230 is written as well as how to trouble shoot in case problems arise.
2. Feature
TCAM-230 is a network camera and a video and audio surveillance transmission system based on IP network through LAN, ADSL/VDSL, and Wireless LAN. n
Video
-
High-quality compression algorithm, H.264
-
Compression in various resolution: CIF, Half-D1, D1
-
Wide range of video transmission rate: 32kbps ~ 4Mbps
-
Various transmission mode: CBR, VBR
-
Motion detection n
Audio
-
Multi-transmission mode: Uni-direction (TCAM-230 -> Client PC or Decoder,
Client PC or Decoder -> TCAM-230), Bi-direction n
Network
-
Static IP and Dynamic IP(DHCP, PPPoE)
-
One to one and one to many connection
-
Multicasting
-
Automatic transmit rate control according to network condition
-4-
TCAM-230 User Manual
n
Serial Data
-
One serial ports (RS-485)
-
Data pass-through mode: Serial data communication between TCAM-230 and
Decoder n
Sensor and Alarm
-
Connections to external sensor and alarm devices
-
Event Alarm n
User Interface
-
System status display utilizing OSD(On Screen Display)
-
System configuration using Internet Explorer n
Reliability
-
Reliable embedded system
-
System recovery utilizing dual watch-dog functions
-5-
TCAM-230 User Manual
3. Product and Accessories
TCAM-230 System User Manual
Power adaptor and cable CMS S/W CD
<Picture 1> Product and Accessories
-6-
4. Part Names and Functions
n
Rear
TCAM-230 User Manual
1
2 3
4
6, 7
5
9
8
Connector
1. LAN/802.3af
2. AUDIO OUT
3. AUDIO IN
Function
LAN port/802.3af PoE (Power over Ethernet)
Audio output
Audio input
4. RESET Button
5. POWER IN
Reset button for network reset
DC 12V power input
6. SENSOR/ALARM Sensor input/ Relay output
7. RS-485
8. POWER LED
9. VIDEO OUT
Serial port. Support RS-485 protocol
Power LED
Video output
-7-
TCAM-230 User Manual
5. System Connections
TCAM-230 systems can be connected in either 1-to-1 fashion where one TCAM-230 is connected one PC client or decoder system or 1-to-many fashion where one TCAM-230 connected to many PC and decoder systems. (TCS-200 video server can work as a decoder system which takes the data from a video server or IP camera, decodes and outputs analog video.) n
Topology
Generally, the TCAM-230 and the PC & decoder are connected in 1-to-1 mode or 1-tomany connection is also supported.
²
1:1 Connection (Unidirectional)
Site
TCAM
Remote Center
Decoder
Site
Remote Center
TCAM PC
Mostly used configuration is 1 to 1 connection. A TCAM-230 is installed at a site where video images can be transmitted and a PC or a decoder is installed at a center location to receive and view the video images on analog monitor. Audio and serial data are transferred in either direction.
²
1:N Connection (Unidirectional)
-8-
Site
TCAM
TCAM-230 User Manual
Remote Center
PC or Decoder
PC or Decoder
PC or Decoder
In this configuration, a site can be monitored from many remote center locations.
Although up to 64 PCs or decoders can be connected to on TCAM-230, in the real network environment, network bandwidth can limit the maximum connections.
Functionally, the central monitoring system software can replace the decoder.
Multicast Mode
Within the network that supports multicasting, a large number of decoders can be used to receive video effectively from an TCAM-230 using a single streaming of video and audio.
²
Relaying
Site
Center 1 Center 2
TCAM Decoder Decoder
In this arrangement, video and audio can be retransmitted from a center to another center. The arrangement is useful when the network bandwidth to the site is limited
-9-
TCAM-230 User Manual
while there are more than one center wanting to monitor the site.
²
Central Monitoring System
Site
Remote Center
TCAM
CMS
Site
TCAM
Remote Center
Decoder CMS
CMS (Central Monitoring System) is a Windows based remote monitoring program to access multiple TCAM-230 for real-time monitoring or control of the encoders and connected cameras. Please refer to CMS User Manual for more information on CMS.
-10-
TCAM-230 User Manual
2. Installation
1. Connecting Network(LAN)
Connect LAN and there is a Video output to check video quality.
2. Connecting Audio
Audio is bi-directional in any configuration. If necessary, it can be configured to be in transmit-only, receive -only or bi-directional mode.
- Connect audio input and output ports to audio devices accordingly.
- Audio signal is in line level, therefore, microphone or speaker with amplification function should be used.
3. Connecting Serial Ports
The serial port (RS-485) in TCAM-230 can be connected to external equipment such as
PTZ receiver etc. Then, PC client can send PTZ commands to the external equipment via serial port. When a decoder system instead of PC client is connected to TCAM-230, the serial port of TCAM-230 and that of the decoder system works in pass-through mode. That is, data at one port are delivered to the other port, vice versa.
4. Connecting Sensor and Alarm
Connect sensor and alarm devices to corresponding terminals accordingly.
5. Connecting Power
After confirming the power source, connect power adaptor and connect the 12V DC connector to the system. Soon the system will boot up to an operating mode.
-11-
TCAM-230 User Manual
6. Check if It Works
As soon as the power is supplied to the system, it will boot and, after about 30 seconds, the system will be ready for operation.
3. System Operation
1. Remote Video Monitoring
There are two ways to view the video once connections are made between the site and center system. In order for a proper operation, an IP address must be set accordingly and please refer to True Manager Manual or Remote Setting in Chapter 5 for a further details.
Default ID : admin Password : 1234
n Video Monitoring with Decoder System
Once the TCAM-230 IP address is set in the remote IP address section of the decoder, the decoder system will connect to the TCAM-230 and start receiving the video images.
Normally, a monitor connected to the decoder will display video images. n Video Monitoring using Internet Explorer
If an encoder’s IP address in entered on the Internet Explorer, the system will ask for confirmation to install Active-X control. Once authorized, the Internet Explorer will start to display video images from the encoder as shown below.
http://192.168.10.100
-12-
TCAM-230 User Manual
2. Initialization of IP Address
If a system IP address is lost, the system can be reset to a known IP address using the reset button in the back side of the system:
While system is in operation, press the reset button more than 5 seconds.
The system will reboot automatically
Once the system has been rebooted, IP address will be set to the following.
-
IP mode: Fixed IP
-
IP address: 192.168.10.100
-
Subnet mask: 255.255.255.0
-
Gateway : 192.168.10.1
-
Base port : 2222
-
Http port : 80
-13-
TCAM-230 User Manual
4. Remote Configuration
1. Using Internet Explorer
The server can be configured using web browser. Type IP address of TCAM-230 in the address input area of Internet Explorer, then a live viewing screen will be displayed.
Press Setup button located in the upper right area of the monitoring screen, then the se page for server setup will be displayed.
Enter IP address
Press Setup button
The configurations are grouped into 9 categories: System, Video, Audio, Network,
Serial, Event, Preset, User and Camera. Any configuration changes are not applied until Apply is pressed. Leaving the page without pressing Apply button, changes in the page will be discarded.
-14-
2. TCAM-230 Configuration
2.1 System Configuration
TCAM-230 User Manual
-15-
TCAM-230 User Manual
n Video Standard
Video signal type: Select NTSC or PAL n System ID
System ID: Alphanumeric System ID to be transferred to remote software n Language
Language to be used for web-based configuration (7 different languages including English) n Firmware version
Current firmware version n Start Time
Latest system boot date and time n Current Time
Current date & time: Enter a new date and time and press Set Current Time button to update date & time. n Time Zone
Time zone: Select time zone of where the system is installed. Depending on the time zone, Daylight Saving Time will work automatically.. n Automatically synchronize with NTP server
Synchronize system time with an NTP server using NTP (network time protocol). Name of the NTP server should be registered on NTP server Name.
-16-
TCAM-230 User Manual
n Reboot Server
Pressing Reboot Server button will cause the system to reboot. Do not press the Reboot button unless the server needs a reboot. n Factory Reset
Set all settings to the factory default values. System log and user registrations are also cleared.
-17-
2.2 Video Configuration
TCAM-230 User Manual
-18-
TCAM-230 User Manual
n Preference
Preference in video compression and transmission: With ‘Bitrate’ selected, the video compression will be effected by the ‘Bitrate’ value entered. With
‘Quality’ selected, the video compression will be effected by the quality of image selected. Therefore, ‘Bitrate’ and ‘Quality’ corresponds to CBR and
VBR respectively. n Resolution
Selectable video compression resolution:
NTSC: 720X480, 720x240, 352X480, 352X240
PAL: 720X576, 720X288, 352X576, 352X288 n Frame rate
Selectable video frame rate: Determine the maximum number of frames of video images to compress. The frame rate of actually transmitted video can be affected by the network bandwidth limitation. n Quality
Video image compression quality: The selection is possible with
Preference is set to ‘Quality’. n Bitrate
Video bitrate: The value is applicable when Preference is set to ‘Bitrate’. n I-Frame Interval
I-frame interval: Possible values between 0 and 255. There will be no Iframes if 0 is selected.
-19-
TCAM-230 User Manual
n Use Motion Detection
Turn on/off motion detection operation. n Motion Detection Area Editing
Configure regions for motion detection. Regions of arbitrary shape can be configured by the following steps.
Enable Edit item.
Select editing Mode. Set is for including cells to motion detection region and Erase is for excluding.
Select cells using the right button of the mouse. Multiple cells can be selected conveniently by press and dragging.
Press Apply Edited Area to save the editing. n Sensitivity
A condition to trigger an event with motion detection. The value determines the sensitivity of the motion detection within a block: the
-20-
TCAM-230 User Manual
smaller, the more sensitive. n Information Display
System ID and/or server time can be display over the video window in
Internet Explorer. Each item can be turn on or off separately, and position also can be configured. These information are displayed after the video is decompressed. n Burn-in OSD
Insert system ID and date/time in the compressed video. Separately
System ID and Time can be turned On or Off in the video. Position specifies the position of such data. n Brightness
Control input video brightness by selecting values between 0 and 100. n Contrast
Control input video contrast by selecting values between 0 and 100. n Hue
Control input video Hue by selecting values between 0 and 100. n Saturation
Control input video saturation by selecting values between 0 and 100.
2.3 Audio Configuration
-21-
TCAM-230 User Manual
n Mode
Select audio operation mode.
Mode
Off
Tx-Only
Rx-Only
Tx & Rx
Action
No operation
Transmit only
Receive only
Transmit and Receive n Input Gain
Set audio input gain.
-22-
2.4 Network Configuration
TCAM-230 User Manual
-23-
TCAM-230 User Manual
n IP Mode
Three IP modes are supported. Depending on the selected mode, further configuration items come as follows.
IP Mode Selection
Local IP
Description
Fixed IP address
Fixed IP
Local Gateway Gateway IP address
Local Subnet Subnet mask
DHCP
N/A
☞ Please ask an IP address information from ISP provider or network manager. n DNS
Set DNS server IP address. n Base Port
Network base port is used for communication between systems. In order for the servers and remote systems to be connected together, the port number must be identically set. n HTTP Port
HTTP port use for web-based connection n RTSP Port
RTSP port used for RTSP-based connection n Multicast IP
The multicast IP address selection range is between 224.0.1.0 and
-24-
TCAM-230 User Manual
238.255.255.255. The selection can be used only when media protocol is set to
Multicast. The multicast address must be the same for the system to be connected using multicast protocol. n DDNS
Select the DDNS(Dynamic DNS) server to use. One of the two servers can be selected.
- TrueDNS : use TrueDNS service. Systems can be registered on the website for TrueDNS service: http://ns1.truecam.net
. System will get a domain name of xxx.truecam.net style. Refer user guide document for True DNS service.
- DynDNS : use DynDNS service. Refer www.dyndns.org
for details. n Flow Control Mode
When several clients connect to a server, bandwidths of networks clients may differ and some clients may not receive encoded stream fully. To handle such situation, three flow control modes which can be chosen according to users’ preference are provided.
Mode
Min
Max
Adjust
Off
Description
The bitrate is automatically adjusted to a client with smallest network bandwidth.
The bitrate automatically adjusted to a client with largest network bandwidth size. When set to this mode, a client with smaller bandwidth will not receive all frames of video.
The bitrate is adjusted to most optimum rate by learning the network bandwidth.
Flow control is off.
-25-
TCAM-230 User Manual
n Address Info
Display network related information.
IP Address
The server own IP address. This information is useful when the server’s IP mode is set to DHCP.
Domain Name
In case the server is registered with DDNS server, the registered domain name is displayed.
MAC Address
Display the MAC address of the server. In case the server is registered with DDNS server, the MAC address is used in DDNS registration.
-26-
2.5 Serial Port Configuration
TCAM-230 User Manual
In case for the user who use TCAM-230/250/251/270, there might be very seldom case to use this Serial port. n Serial Port Configuration
-27-
TCAM-230 User Manual
Differ to TCS-200 Video server, there are one serial ports, RS-485, in TCAM-230. n Sensor Type
There are one sensor input ports on TCAM-230. The sensor port can be configured to the following.
Function
OFF
NO (Normally Open)
Operation
Not used
The port is normally open and activated when closed.
NC (Normally Closed)
The port is normally closed and activated when opened.
The function of the sensor port is set based on the type of the sensor connected.
-28-
2.6 Event Configuration
TCAM-230 User Manual
The TCAM-230 has one sensor port and alarm port. Actual numbers of sensor, alarm ports and beep may vary depending on models.
When a decoder system instead of a PC client is connected to a TCAM-230, one system becomes a Local system and the other a Remote system (Generally a system
-29-
TCAM-230 User Manual
which is being used by the user is called as Local system). Then, actions for events can be configured for events from remote system as well as for local system. For example, it is possible to turn on an alarm device in local (center) decoder system when a sensor device in remote (site) IP camera is triggered. Local section configures the actions for events from local (self) system, and configuration activates local devices and Remote sections configures the actions for events from remote(peer) system.
. The following table lists the possible actions for events.
Action
Sensor In
Alarm out
Description
One sensor in port
Triggers alarm (relay) port.
FTP
Sends E-mail to the specified address. AVI file can be attached
Upload AVI file to a specified FTP server n Sensor
Configure the actions when the sensor is activated. Multiple actions can be set for a single event. n On Video Loss
Configure the actions when video input signal is lost. Multiple actions can be set for a single event. n On Motion
Configure the actions when motion is detected. Multiple actions can be set for a single event.
-30-
TCAM-230 User Manual
n On Disconnect
Configure the actions when the link(connection) with peer system is disconnected. Multiple actions can be set for a single event. n Alarm activation duration
Set the duration of alarm activation in case of an event. If it is set to continuous, it will be in active state until an operator reset it manually. n E-mail Notification
Specify the information to send E-mail as the action of an event. The address of mail (SMTP) server needs to be specified on Server Address field, and Port specifies the port for SMTP operation (Port 25 is the default port in SMTP operation. If different port is configured in the SMTP server, this port needs to be changed accordingly). When the server requires authentication, ID and password of an E-mail account need to be entered also. Destination address needs to be entered on Destination Address field. More than one address can be entered by delimiting comma (,) or semi-colon (;). Destination address can take up to 63 characters. Video clip of AVI file format at the moment of the event can be attached by setting Video Clip Attaching. n FTP Upload
Specify the information for uploading video file as the action of an event. The address of an FTP server to receive video files is specified on Server Address field, and Port specifies the port for FTP operation (Port 21 is the default port in
FTP operation. If different port is configured in the FTP server, this port needs to be changed accordingly.). ID and password for accessing the FTP server also need to be specified.
By setting Continuous Upload to On, it is possible to upload video clip
-31-
TCAM-230 User Manual
periodically regardless of events. Upload Duration specifies the duration of one upload file, and Upload Interval specifies how often it should happen.
Upload Interval doesn’t include the duration. If Upload Interval is 60 and Upload
Duration is 20, it uploads a file for 20 seconds duration every 80 seconds. n Event Recording
Specify how a video clip is to be generated for E-mail sending or FTP uploading.
Pre-event Time specifies the duration of recording before an event happens.
Post-event Time specifies the duration after the event is cleared.
-32-
2.7 Preset Configuration
TCAM-230 User Manual
Preset Name
Move PTZ Camera to normal view
Press Set Button
Save
This function is available for using TCAM-270 in order to control PTZ effectively.
Configure up to 15 preset positions. Preset function is not available on some PTZ receivers. Make sure to check if a PTZ receiver supports preset. n Preset Configuration
Set the PTZ Presets by following the next steps.
-33-
TCAM-230 User Manual
Move cameras to desired view using PTZ control buttons.
Enter Preset name.
Press Set button.
Once all the presets are set, press Save List button. n Move to Preset Position
Select a preset from the Preset and press Go To button, then, the camera will move to the selected preset position.
2.8 User Configuration
User can be registered and privilege level of a user can be specified. User configuration is allowed only to admin user. Max 16 users can be registered and each user can have one of four privileges.
-34-
Privilege
Admin
Manager
User
Guest
TCAM-230 User Manual
Allowed Operations
All operations
All operations except for user configuration
Live viewing and PTZ control
Live viewing only
Remarks
User ID = admin n Add User
Page for adding a user comes on pressing Add button.
User ID and password need to be entered and privilege level need to be selected. User ID and password consist of alphanumeric string of max 15 characters. n Delete User
A user is deleted by pressing Delete button. n Change Password
-35-
TCAM-230 User Manual
Pressing Modify Password button after selecting a user shows a page for changing password.
In case changing admin password, old password is checked. n Modify Privilege Level
Pressing Modify Privilege button after selecting a user shows a page for changing the privilege. It is not allowed to change the privilege level of admin user. n Login Policy
Skip Login is provided for convenient access to the server when authentication is not required. When Skip Login is set to Enable, login step is skipped. The privilege level after login in this way is determined by the setting of Privilege
Level After Login Skipped.
-36-
2.9 Camera Configuration
TCAM-230 User Manual
Settings for analog part of the camera can be configured. Camera-specific menu is displayed using OSD on video display, and this menu can be operated with 5 buttons on the page.
-37-
TCAM-230 User Manual
2.10 OSD (On Screen Display) n
How to use
- Press the Set button to access the SETUP mode.
- Select the desired feature using the Up or Down button.
- Change the status of the selected feature using the Left or Right button.
- When completed, move the arrow indicator to ‘EXIT’ and press the Set button
1) Setting up the LENS
Select the lens pressing the Right button.
①
On the SETUP menu screen, move the arrow indicator to the lens using the UP or DOWN button.
②
Select the desired feature using the LEFT or RIGHT button.
③
When DC lens selected, press Set button to control the brightness.
④
Auto Iris Lens (DC Type) is recommended than Manual Lens. Some lens can make a malfunction according to the Brightness Level.
2) Shutter status and speed control
You can control brightness of the screen by the shutter speed.
①
Press the Set button to display the setup menu and move the arrow indicator to ‘SHUTTER’ using the Up or Down button.
②
Set ‘SUTTER’ to the desired mode using the Left or Right button.
③
Off : Deactivation, FLK (1/100) : Flicker mode
④
When WDR is on, the image can flicker a little.
⑤
When setting shutter speed manually (Only for Lens mode), you can select speed from ‘1/60’ to 1/200,000’sec.
⑥
ESC : You can control the BRIGHTNESS.
⑦
When completed, press ‘SET’
⑧
Do not make the camera exposed fluorescent lamp directly not to
-38-
TCAM-230 User Manual
get unstable image in the internal synchronization modes.
When the SHUTTER menu is set to FLK mode, SENS-UP can not work, please control the menu.
3) White Balance (White BAL.)
When needs color control on the screen, use ‘WHITE BALANCE’ function.
①
Press the SET button to display the SETUP menu and move the arrow indicator to ‘WHITE BALANCE’ using Up or Down button.
②
Set ‘WHITE BAL.’ to the desired mode using Left or Right button.
③
ATW (Auto Tracking White Balance) : When color temperature is
2400~12,000k, select this mode. (Ex. A fluorescent lamp, outdoor)
④
AWC (Auto White Balance Control) : The white balance is automatically adjusted in a specific environment. In order to obtain the best result, press the set button while the camera focuses on the white paper. If the environment including the light source is changed, you have to adjust the white balance again.
⑤
Manual : To find adjust, select the Manual mode. You can increase or decrease the red or blue factor while monitoring the difference on the screen. Set to ‘Manual’ mode and press the Set button.
Increase or decrease the value for RED (R-Gain) and BLUE (B-
Gain), watching the color of the picture, and press the Set button when you obtain the best color.
⑥
Proper White Balance may not be obtained under the following conditions in these cases select the AWC mode; when the scene contains mostly high color temperature object, such as a blue sky or sunset. When the scene is dim. If your camera faces fluorescent lamp directly or is installed in the place of the changing illumination.
-39-
TCAM-230 User Manual
4) Backlight
SR chip built-in provides intelligent light level control to overcome the sever
Backlight condition.
①
Press the Set button to display the SETUP menu and move the arrow indicator to ‘BACKLIGHT’ using the Up or Down button.
②
Set ‘BACKLIGHT’ to the desired mode using the Left or Right button
5) Auto Gain Control (AGC)
AGC is to get bright picture. Higher GAIN level, brighter screen. But you can get noise increase.
①
Press the Set button to display the SETUP menu and move the arrow indicator to ‘AGC’ using the Up or Down button.
6) Digital Noise Reduction (DNR)
DNR is to reduce the noise on the screen.
①
Press the Set button to display the SETUP menu and move the arrow indicator to ‘DNR’ using the Up or Down button.
②
Set ‘DNR’ to the desired mode using the Left or Right button.
③
OFF : Deactivation
④
LOW : Low reduction of the noise
⑤
MIDDLE : Middle reduction of the noise
⑥
HIGH : High reduction of the noise
⑦
After image may appear with DNR. If you change the ‘GAIN’ menu from AGC-L to AGC-H, sensitivity is increased as well as noise on the screen. When selected ‘GAIN’ menu OFF, DNR will not work.
7) Sens-Up
You can always get the clear image with this function under night or low lighting level.
①
Press the Set button to display the SETUP menu and move the
-40-
TCAM-230 User Manual
arrow indicator to ‘SENSE UP’ using the Up or Down button.
②
Set ‘Sense Up’ to the desired mode using the Left or Right button.
③
AUTO : When your camera is under night or low-lighting level, select this mode.
④
If you press SETUP button at ’AUTO’ menu, you can control the lowlight action maximum magnifications.(X2~X128)
⑤
Expander the magnifications, you can get the brighter screen as well as the after image sensitivity is increased as well as noise on the screen.
⑥
When increasing the magnifications in case of SENSE UP activated,
8) SPECIAL it may appear noise, spots, whitish. This is not out of order.
①
CAMERA ID : If the camera ID feature is set to ‘OFF’, the name will not displayed in the monitor. However, Camera ID can be set on the System tap of web viewer.
②
Color : You can choose color and B/W mode electronically. (Option)
On : Color mode, OFF : B/W mode, Auto : Generally color mode,
B/W mode in low luminance.
③
SYNC : Two SYNCHRONIZATION modes are available INTERNAL and EXTERNAL LINE-LOCK. In LINE-LOCK mode, it synchronous generator. The line-lock synchronization is only used in the area of
60Hz(NTSC Models) 50Hz(PAL Models). When it used in AC power, L/L mode can be used. In DC 12V, the SYNC menu sets
‘INT’ mode.
④
Whenever your camera detects motion of object displaying
‘MOTION DETECTED’ with the number counted up on the screen.
OFF : Deactivation
ON : MOTION DET. Activated.
-41-
TCAM-230 User Manual
- Press SET button
- Move the arrow indicator to ‘AREA SET’ using Up and Down button, and then press the Set button.
- Set the areas you want to observe.
⑤
PRIVACY : To mask area which you want to mask.
OFF : Deactivation
ON : PRIVACY mode activated.
- Press the Set button
- Move the arrow indicator to area you want to mask.
- Set ‘ON’ using Left or Right button
- Press the Set button and then set the area’s bounds with method like MOTION DET. Set.
⑥
MIRROR : OFF : Deactivation, ON : Make a reverse turn to Right or
Left
⑦
SHARPNESS
- OFF : Deactivation
- ON : SHARPNESS control mode (LEVEL 0~31)
- When level is up, the sharpness will make image clear. Please control the level as you want to get. If the level is to much high, you can get the unnatural image with noise.
⑧
RESET : To reset your camera to FACTORY DEFAULT SETTING.
⑨
RETURN : Save the setting of SPECIAL function, and then move to
SET UP menu.
-42-
Appendix : ALM/SEN/485 Port
- Part Name : DIN-605H(MINI-DIN 6PIN Female)
- Dimension
TCAM-230 User Manual
- Pin Description
- PIN 1 : RS485 RTX+ Signal
- PIN 3 : RS485 RTX- Signal
- PIN 4 : SENSOR IN, Ground Contact Signal
- PIN 6 : SENSOR GND
- PIN 7 : ALARM OUT, RELAY Contact Signal
- PIN 8 : ALARM COMMON
-43-
advertisement
Key Features
- High-quality H.264 compression
- Video resolutions: CIF, Half-D1, D1
- Wide range of video transmission rate
- Motion detection
- Bi-directional audio
- Static and Dynamic IP (DHCP, PPPoE)
- One-to-one and one-to-many connections
- Multicasting
- Automatic transmit rate control
- RS-485 serial port
