EVOHD User Manual.book - Security Service & Communication

EVOHD User Manual.book - Security Service & Communication
EVOHD
User Guide
Revision 1.1
www.paradox.com
Warranty
For complete warranty information on this product please refer to the Limited Warranty Statement found on
the website www.paradox.com/terms. Your use of the Paradox product signifies your acceptance of all
warranty terms and conditions. Please ensure compliance with the applicable laws of local jurisdictions
including privacy laws.
© 2014 Paradox Ltd. All rights reserved. Specifications may change without prior notice. Canadian and
international patents may apply. EVOHD Digiplex is a trademark or registered trademark of Paradox Ltd. or its
affiliates in Canada, the United States and/or other countries. LODIFF® is a registered trademark of Fresnel
Technologies Inc.
For the latest information on products approvals, such as UL and CE, please visit www.paradox.com.
Note:
Note: This hardware or software product (“product(s)”) and its related documentation are provided by
paradox securities for use complying with all local, national, and international laws. Any express or
implied warranties, including, but not limited to, the implied warranties of merchantability, fitness for a
particular purpose and non-infringement are disclaimed. In no event shall Paradox be liable to any
customer or third party for any direct, indirect, special, exemplary, or consequential damages of any
kind (including, but not limited to, payment for procurement of substitute goods or services; loss of
property, data, or profits; or business interruption) however caused and on any theory of liability,
whether in contract, strict liability, or tort (including negligence or otherwise) arising in any way from
the use of the product(s) and related documentation.
Contents
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Chapter 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1
Chapter 2
Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Basic Operation Keypads K641 Series . . . . . . . . . . . . . . . . . . . . . 7
2.1
Confidential Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.2
LED Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.3
Auditory Feedback (Beep Tones) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Chapter 3
REM2 Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1
Chapter 4
Other Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Partitioned System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1
Chapter 5
Area Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1
Exit Delay Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.2
Regular Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.3
Stay Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.4
Instant Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.5
Force Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.6
Bypass Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.7
Keyswitch Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.8
Auto-Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 6
Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.1
Entry Delay Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.2
Disarming an Armed System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.3
Alarm Memory Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Chapter 7
Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.1
EVOHD User Manual
System Master Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3
7.2
Copy User Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.3
User Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.4
Deleting User Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.5
Programming User Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.6
User Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.7
Access Control User Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Chapter 8
Using Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.1
Entering & Exiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.2
Arming and Disarming with Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.3
How Access Control Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Chapter 9
Trouble Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9.1
Trouble Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9.2
Event Record Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Chapter 10
Additional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.1
Programmable Outputs (PGMs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.2
Keypad Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.3
Setting Time & Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.4
Programming Chime Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10.5
Panic Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10.6
Quick Function Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Chapter 11
VDMP3 Plug-In Voice Dialer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
11.1
Calling the VDMP3 (outside line) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
11.2
Receiving a Call From the VDMP3 (alarm in system) . . . . . . . . . . . . . . . . . . . . . . 29
Chapter 12
Testing and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
12.1
Burglar Alarm Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
12.2
Fire Alarm Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
12.3
System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
12.4
System Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Chapter 13
Fire and Burglar Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
13.1
4
Standard Fire Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
EVOHD User Manual
13.2
Delayed Fire Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
13.3
Fire Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
13.4
Minimizing Home Fire Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
13.5
Home Fire Warning System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
13.6
Burglar Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Chapter 14
Basic Operation of the TouchPad TM50 . . . . . . . . . . . . . . . . . . . 34
14.1
Touchpad Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
14.2
Touchpad Security Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
14.3
Touchpad Control Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
14.4
Touchpad Add-on Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
14.5
Touchpad Personalize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
14.6
Touchpad User Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
14.7
Touchpad Advanced Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
14.8
Touchpad System Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
AppendixA ............................................................................................................38
Hebrew Special Characters ............................................................................................................. 38
AppendixB ............................................................................................................39
Russian Special Characters.............................................................................................................. 39
AppendixC .............................................................................................................40
Greek Special Characters ................................................................................................................. 40
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
EVOHD User Manual
5
Introduction
1
Introduction
1
Your EVO System is an advanced technology security system that will provide you with reliable security
protection and powerful features that are easy to use. The elegant and user-friendly keypads will allow you easy
access to your security system's functions and information at the touch of a button.
Messages will be displayed differently depending on the keypad you have selected. The 32-character screen on
LCD keypads will display messages and menus to guide you through the system’s operations. Your installer can
even customize the messages on keypads for your home or business.
Since you can communicate your instructions to your system through the keypad, please read this manual
carefully and have your installer explain basic system operation.
1.1 Legend
NOTE:
Indicates a warning or an important note.
NOTE:
Indicates useful information or a tip.
[TEXT] Indicates information that must be entered on the keypad.
6
EVOHD User Manual
Basic Operation Keypads K641 Series
2
Basic Operation Keypads K641 Series
2
2.1 Confidential Mode
Your installer can program keypads to hide the status of your system automatically by changing the keypad to
Confidential Mode.
In Confidential Mode:
• The zones and status messages will NOT be displayed
• The indicator lights will NOT illuminate
• Depending on how your keypad was programmed by your installer, you must either press a button or enter
your user access code to illuminate the indicator lights and activate Normal Mode.
2.2 LED Assignments
The following sections will introduce you to the functions of the buttons, lights, and messages on your keypad.
Figure 1: LCD Keypad Basic Overview
AC Light:
ON
= AC power
OFF
= Power failure
STATUS Light:
When Green:
ON
= All zones are closed.
OFF
= One or more zones are
open.
FLASH
= Exit Delay in progress
The LCD screen will guide you
with detailed messages.
Use the arrow buttons to scroll
through the current menu when the
arrows appear in the LCD screen.
When Red:
ON
= Area(s) armed
OFF
= Area(s) disarmed
2.3 Auditory Feedback (Beep Tones)
When you enter information on the keypad, the keypad will guide you with beep tones to communicate the
acceptance or rejection of your entries.
Confirmation Beep: When an operation (i.e. arming/disarming) is successfully entered or when the system
switches to a new status/mode, the keypad emits an intermittent beep tone (“BEEP-BEEP-BEEP-BEEP-BEEP”).
Rejection Beep: When the system reverts to a previous status, or when an operation is incorrectly entered, the
keypad emits a continuous beep tone (“BEEEEEEEEEEP”).
EVOHD User Manual
7
REM2 Feedback
3
REM2 Feedback
3
If your system includes the Wireless Zone Expansion module (RTX3), it will be able to support the Two-Way
Remote Control (MG-REM2). This remote allows you to change the status of the system, and it also provides
visual and auditory feedback.
Table 1: Full/Force Arming Indicators
Action
LED Sequence
Auditory Sequence
Disarming
Green on
TWO BEEPS
Exit delay
Red / green slow flash
CONFIRMATION BEEP
Arming / Entry Delay
Red on
CONFIRMATION BEEP
Alarm
Red fast flash
ALARM BEEP
Table 2: Stay Arming Indicators
Action
LED Sequence
Auditory Sequence
Disarming
Green on
TWO BEEPS
Exit delay
Yellow / green slow flash
CONFIRMATION BEEP
Arming / Entry Delay
Yellow on
CONFIRMATION BEEP
Alarm
Red fast flash
ALARM BEEP
NOTE:
To see correct indications with REM 2 you must press the “i “ in the middle of the remote. This will show
the correct status.
3.1 Other Indicators
Table 3: Other Indicators
Action
LED Sequence
Auditory Sequence
PGM on/off
Yellow on
CONFIRMATION BEEP
8
EVOHD User Manual
Partitioned System
4
Partitioned System
4
Your installer can set your keypad to recognize separate protected areas. A separated system is called a
partitioned system, which can be useful in situations where shared security systems are more practical. For
example, a company that has both an office and a warehouse area, can arm and disarm each area separately
while controlling access to each area. Therefore, one person may have access to only one area, whereas another
person may have access to all areas. Access to the areas is determined by the User Access Code.
4.1 Area Display
The Area Status Display enables you to see the status of the individual areas within a partitioned system. Your
installer can partition the system into separate areas.
To view the status of the areas:
1. Enter your [ACCESS CODE], and then press the [1] button.
2. Press the button corresponding to the area (i.e. 1, 2,...8), or use the [] and [] buttons and press [ENTER]
when the area you want to view appears on the screen.
3. Press [CLEAR] to exit.
In Area Status Display mode, the following information will scroll on the LCD screen:
• ready: if all zones in the selected area are closed.
• not ready: if zones in the selected area are open.
• Front Door Open: if there is an open zone within that area.
• Trouble(s): (section 9) if a trouble has occurred.
• Alarms in Memory: (section 6.3) if an alarm has occurred.
• Armed; Force Armed; Instant Armed; Stay Armed: displays the arming status of the selected area.
In Area Status Display, the following will illuminate for the area selected:
• The area lights (A1, A2, A3, and A4) if the associated area is armed. For example, if you have selected area 3
and it is currently armed, A3 will illuminate.
• The numerical light(s) representing any open zone(s) in a corresponding area or areas.
• The Mem action light if any alarms have occurred.
• The Trbl action light if any troubles are occurring.
• The Stay action light if the area is Stay or Instant Armed.
• The Force action light if the area is Force Armed.
• The Byp action light if zones are bypassed.
EVOHD User Manual
9
Arming
5
Arming
5
When your system is armed, it can respond to any breach in the protected zones by causing an alarm and sending a
report to your monitoring station.
5.1 Exit Delay Timer
When you arm your system, it will trigger the Exit Delay Timer to provide you with enough time to exit the
protected area before the system is armed.
5.2 Regular Arming
This method is used for the everyday arming of your system. All zones within the protected area must be closed
to Regular arm the system.
To Regular arm the system:
1. Enter your [ACCESS CODE].
2. Press the [ARM] button.
3. If you have access to more than one area, select the area(s) you wish to Regular arm (refer to section 4.1).
5.3 Stay Arming
Stay arming will partially arm your system to permit you to remain in your home or office by arming the outer
zones (perimeter) of the protected area (i.e. doors and windows).
To Stay arm:
1. Enter your [ACCESS CODE].
2. Press the [STAY] button.
3. If you have access to more than one area, select the area(s) you wish to Stay arm (refer to section 4.1).
5.4 Instant Arming
This feature is the same as Stay arming except that there is no Entry Delay. Therefore, any armed zone that is
breached will immediately generate an alarm.
To Instant arm:
1. Enter your [ACCESS CODE].
2. Press the [5] button.
3. If you have access to more than one area, select the area(s) you wish to Instant arm (refer to section 4.1).
5.5 Force Arming
Force arming allows you to quickly arm your system when zones are open. However, once the open zone is
closed, your system will then arm that zone as well.
10
EVOHD User Manual
To Force arm:
1. Enter your [ACCESS CODE].
2. Press the [FORCE] button.
3. If you have access to more than one area, select the area(s) you wish to Force arm (refer to section 4.1).
5.6 Bypass Programming
You can bypass certain zones when you arm the protected area(s). When a zone is bypassed, it will be ignored
the next time your system is armed. Once your area is disarmed, the system will unbypass the zone.
To Bypass a zone:
1. Enter your [ACCESS CODE].
2. Press the [BYP] button.
3. Enter the zone number (i.e. 01, 02,...96), or use the [] and [] buttons and press [BYP] once the zone you
want to bypass appears on the screen. If bypassed, the byp light does not appear on the screen and the
keypad emits a rejection beep, you may not have access to bypass that zone.
4. Repeat step 3 until all zones you want to bypass have been selected.
5. Press the [ENTER] button to save and exit.
To view all bypassed zones.
1. Enter your [ACCESS CODE].
2. Press the [BYP] button.
3. Scroll through the zones using the [] and [] buttons to view zone status. (LCD Keypads)
NOTE:
In order to bypass a zone, the following conditions must be met:
•
•
•
•
WARNING:
The zone must have the Bypass option programmed by your installer.
The Bypass option must be enabled in your User Options.
Your user access code must have access to the zone’s Area Assignment.
The zone’s area must be disarmed before the zone can be bypassed.
Fire Zones cannot be bypassed.
5.6.1 Bypass Recall
Bypass Recall reinstates the zones that were bypassed the last time your system was armed.
To activate Bypass Recall:
1. Enter your [ACCESS CODE].
2. Press the [BYP] button.
3. Press the [MEM] button.
Zones bypassed the last time your system was armed are bypassed.
4. Press the [ENTER] button to save and exit.
EVOHD User Manual
11
5.6.2 One-Touch Buttons
If enabled by your installer, you can access the following features without using your user access code by
pressing and holding the desired One-Touch button.
Table 4: One Touch Button
Button
Feature
[ARM]
Regular arm
[STAY]
Stay arm
[FORCE]
Force arm
[BYP]
Bypass Programming
[DISARM]
Disarm a Stay/Instant armed area
[5]
Instant arm
[6]
Change display settings
[7]
View Event Record display (LCD Keypads only)
5.7 Keyswitch Arming
A key can be used to arm and disarm your system using two forms of keyswitches. With a Maintained
Keyswitch, place the key in the “ON” position to arm your system, and place the key in the “OFF” position to
disarm your system. With a Momentary Keyswitch, place the key in the “ON” position briefly then place it back
in the “OFF” position to arm the system. Repeat this process to disarm with a Momentary Keyswitch.
5.8 Auto-Arming
If enabled by your installer, you can set the time that an area will arm itself automatically.
5.8.1 Timed Auto-Arming
Your installer can set Timed Auto-Arming to function in either Force or Stay arming mode. A sixty-second
(default value) Exit Delay sequence will begin prior to your system automatically arming itself at the
programmed time.
To set the Auto-Arming timer:
1. Enter your [ACCESS CODE].
2. Press the [0] button.
3. Press the [MEM] button.
4. If you have access to more than one area, press the area’s number, or use the [] and [] buttons and
press the [ACC] button when the area you want to program appears on the screen.
5. Enter the time you want the area to be armed according to the 24-hour clock (i.e. 9 a.m. is 09:00 and 9 p.m.
is 21:00).
6. Press the [ENTER] button to save and exit.
12
EVOHD User Manual
5.8.2 No Movement Auto-Arming
Your system can be programmed to send a report to your monitoring station and/or arm the system if there is
no activity in the area during a specified period of time. Your installer can set No Movement Auto-Arming to
function in either Regular or Stay arming mode.
EVOHD User Manual
13
Disarming
6
Disarming
6
When your system is disarmed, it deactivates any alarms in progress, and it deactivates the zones so the alarm
will not be triggered if zones are breached.
6.1 Entry Delay Timer
Your installer will program designated entry points (i.e. the front door) with an Entry Delay Timer. This delay
gives you time to enter the armed premises and enter your code to disarm your system before the alarm is
triggered.
6.2 Disarming an Armed System
You can only disarm an area to which your user access code is assigned. User access codes with the “Arm Only”
(section 7.6) option enabled cannot disarm an armed system.
To disarm the system:
1. Enter your [ACCESS CODE].
2. Press the [DISARM] button. If you have access to more than one area, select the area(s) you wish to disarm
(refer to section 6.2).
To disarm a system in alarm:
1. Enter your [ACCESS CODE].
2. In the case of a false alarm, call your monitoring station quickly to advise them of the false alarm.
WARNING:
In the case of a burglar alarm, leave the premises and call the Police from a safe location.
6.3 Alarm Memory Display
When an alarm occurs in a zone:
• The area and zone (i.e. Alarm Area 1 - Front Door) are displayed / zone’s LED flashes even when the system is
armed. The notification continues until disarming, even if the zone is restored.
• The alarm memory will be erased after the next alarm occurs and a valid code has been entered.
To view the alarms that occurred the last time the system was armed:
1. When the system is disarmed, the LCD keypad’s screen will display Alarm in Memory: Press [mem].
2. Press the [MEM] button.
Each zone that was breached while armed will appear below Alarm in:.
The MEM action light will flash and the numerical light(s) for each zone whose alarm was triggered will illuminate.
3. Press the [CLEAR] button to exit the Alarm Memory Display.
14
EVOHD User Manual
Access Codes
7
Access Codes
7
Access Codes allow access to the system. Your system supports up to 999 user access codes. Codes are given a
User Number between 002 and 999 (User Number 001 is the System Master Code). Your installer will program
user access codes to be four, six, or variables of one to six digits in length. Each digit can be any value between
zero and nine. If your installer programmed your system to accept a variable code length, you have to press the
[ENTER] button after entering your user access code.
7.1 System Master Code
The System Master Code will give you access to all the features available on your system, as well as the ability to
add, modify, or delete any user access codes. We suggest that you change this code to prevent others from
accessing and changing options without authorization. Your installer can set the System Master Code to be
either 4 or 6 digits in length.
To change the System Master Code:
1. Enter the current [SYSTEM MASTER CODE] (Default 1234 for 4 digit code; 123456 for 6 digit code).
2. Press the [0] button.
3. Press the [ACC] button.
4. Enter the numbers [001].
5. Enter a [NEW CODE].
6. Press the [ENTER] button to save and [CLEAR] to exit.
WARNING:
NOTE:
The System Master Code has access to all Access Control doors and all Access Control
features at all times. Only the card’s serial number and the choice of arming method can be
changed. If the other options are manually changed, the System Master Code will
immediately revert to its original programming.
You can assign a label (name) to a user access code at any point during the “Programming User Access
Code” process. Refer to section 7.3 to assign a User Label.
7.2 Copy User Options
This feature allows you to copy the User Options, Access Control Options, and Area Assignments from one user
access code to another. All User Options are copied except the User Code, Card Assignment, and User Label.
To copy user options:
1. Enter your [ACCESS CODE] (User access code with Master feature).
2. Press the [0] button, and then the [ACC] button.
3. Enter the 3-digit User number you wish to copy TO.
4. Press the [MEM] button.
5. Enter the 3-digit User number you wish to copy FROM.
EVOHD User Manual
15
6. Enter a user code. If the user code is of variable length, press the [ENTER] button after entering the user
code. If necessary, assign an Access card (step 13 in section 7.5.1) and User Label (section 7.3).
7. Press [ENTER] to save and exit.
7.3 User Labels
User labels personalize user access codes and can be assigned by pressing [ENTER] at any point after step 4
during the programming of user access codes (refer to section 7.5.1). For Example, LCD keypads can display
John Smith Select Action.
To program a user label:
1. Enter your [ACCESS CODE] (User access code with Master feature).
2. Press the [0] button, and then the [ACC] button.
3. Enter the 3-digit User number you wish to label.
4. Press the [ENTER] button twice. the first time you will get to REMOTE control configuration the second time
you will get to User Label.
5. Type the desired characters as detailed in section 7.3.1 and section 7.3.2.
6. Press the [] button to move the cursor to forward.
7. Press the [] button to move the cursor to back.
8. Repeat steps 2 and 3 until the desired label is complete.
9. Press the [ENTER] button to save and exit.
7.3.1 Keypad Buttons
Every numeric button on the LCD keypads is assigned a set of letters. To obtain the desired letter using the
numeric buttons on your keypad, press the button until the desired letter appears on the screen. For example, if
you wanted to enter the letter “C” you would press the [1] button three times (refer to Table on page 16). If
using a Hebrew keypad, refer to Table 9 in Hebrew Special Characters on page 38. If using a Russian keypad,
refer to Table 11 in Russian Special Characters on page 39. If using a Greek keypad, refer to Table 13 in Greek
Special Characters on page 40.
Table 5: Keypad Letter Assignments
Key
Press Key
Once
Press Key
Twice
Press Key
Three
Times
[1]
A
B
C
[2]
D
E
F
[3]
G
H
I
[4]
J
K
L
16
EVOHD User Manual
Table 5: Keypad Letter Assignments
Key
Press Key
Once
Press Key
Twice
Press Key
Three
Times
[5]
M
N
O
[6]
P
Q
R
[7]
S
T
U
[8]
V
W
X
[9]
Y
Z
7.3.2 Special Function Keys
[STAY] = Insert Space
Pressing the [STAY] key inserts a blank space in the current cursor position.
[FORCE] = Delete
Pressing the [FORCE] key will delete the character or blank space found at the current cursor position.
[ARM] = Delete Until the End
Pressing the [ARM] key will delete all characters and spaces to the right of the cursor and at the cursor's position.
[DISARM] = Numeric Keys / Alphanumeric Keys
Every time the [DISARM] key is pressed it will toggle from numeric keys to alphanumeric keys and vice versa.
Numeric: Keys [0] to [9] represent numbers 0 to 9.
[BYP] = Lower Case / Upper Case
Every time the [BYP] key is pressed it will toggle the case setting from lower to upper case and vice versa.
[MEM] = Special Characters
After pressing the [MEM] key, the cursor will turn into a flashing black square. Using Table 6 on page 18,
enter the 3-digit number that represents the desired symbol. If using a Hebrew keypad, see Hebrew Special Characters Catalogue on page 38. If using a Russian keypad, see Russian Special Characters Catalogue on page 39. If using a Greek keypad, see Greek Special Characters Catalogue on page 40.
EVOHD User Manual
17
Table 6: Special Characters Catalogue
032
048
064
080
096
112
128
144
160
176
192
208
224
240
033
049
065
081
097
113
129
145
161
177
193
209
225
241
034
050
066
082
098
114
130
146
162
178
194
210
226
242
035
051
067
083
099
115
131
147
163
179
195
211
227
243
036
052
068
084
100
116
132
148
164
180
196
212
228
244
037
053
A069
085
101
117
133
149
165
181
197
213
229
245
038
054
070
086
102
118
134
150
166
182
198
214
230
246
039
055
071
087
103
119
135
151
167
183
199
215
231
247
040
056
072
088
104
120
136
152
168
184
200
216
232
248
041
057
073
089
105
121
137
153
169
185
201
217
233
249
042
058
074
090
106
122
138
154
170
186
202
218
234
250
043
059
075
091
107
123
139
155
171
187
203
219
235
251
044
060
076
092
108
124
140
156
172
188
204
220
236
252
045
061
077
093
109
125
141
157
173
189
205
221
237
253
046
062
078
094
110
126
142
158
174
190
206
222
238
254
047
063
079
095
111
127
143
159
175
191
207
223
239
255
Polish
Hungarian
Turkish
001
002
003
001
002
003
004
005
006
007
001
7.4 Deleting User Access Codes
To delete user access codes, follow steps 1 to 4 in section 7.5.1, but press the [CLEAR] button in Step 4. Once
the information is erased, press the [ENTER] button to save and exit.
7.5 Programming User Access Codes
The System Master and Users with the Master feature can program user access codes with User Options and
Area Assignments. The section 7.5.1 describes the steps you would follow to program user access codes. If you
wish to program user access codes using the NEware Software, please contact your installer for information.
If the keypad emits a rejection beep at any point during the programming procedure, you may have chosen an
existing user code or you do not have access to certain User Options (section 7.6) and Area Assignments (step 7
in section 7.5.1). Users with the Master feature can only assign User Options and Area Assignments that they
are assigned to. For example, if a User with the Master feature is assigned User Option 1 and Area 2, they can
only assign Option 1 and Area 2 to a user access code.
18
EVOHD User Manual
7.5.1 Programming User Settings
Notes:
- For a detailed description of the User Options,
see section 7.6.
- By default, all users can regular arm the system.
Note:
- FOR A DETAILED DESCRIPTION OF THE
ACCESS CONTROL
User Options, see section 7.7
User Labels on page 16.
NOTE:
If no area is assigned, and if PGMs are programmed by your installer, the user can only control
the PGMs. Refer to section 10.1 for a more detailed explanation of PGMs.
Figure 2 – User Programming
EVOHD User Manual
19
7.6 User Options
Options [1] and [2]: Master Feature
When option [1] is OFF, the User cannot program other users into the system.
When option [1] is ON and option [2] is OFF, the user can program and modify user access codes (P.I.N. only) and
User Labels.
When both options [1] and [2] are ON, the user has Full Master rights. The user can create or modify user access
codes, User Options, User Access Control Options, Access Card Numbers, User Labels and Area Assignments
according to their own programming. For example, if the Full Master User has access to area #1 and option [4]
(Bypass) only, the Full Master user can only assign area #1 and option [4] to other users in the system.
Option [3]: Duress
When option [3] is ON, the Duress feature is enabled. This feature is used when someone forces a user to arm or
disarm an area(s). By entering a user access code (P.I.N.) reserved for the Duress feature, the system will arm or
disarm the area(s), and then send a silent alarm to the monitoring station.
Option [4]: Bypass
When option [4] is ON, the Bypass feature is enabled. This feature allows the user to deactivate zones when
arming the area(s).
Option [5]: Arm Only
When option [5] is ON, the Arm Only feature is enabled. The user can arm assigned areas with either a card or
code, but cannot disarm. When the option is OFF, the user can either arm or disarm assigned areas.
Option [6]: Stay & Instant Arm
When option [6] is ON, the Stay and Instant arm features are enabled. The user can now Stay or Instant arm their
assigned areas.
Option [7]: Force Arm
When option [7] is ON, the Force arm feature is enabled. The user can now Force arm their assigned areas.
Option [8]: Area Access
When option [8] is ON, the keypad will permit access to all the areas assigned to the user access code. When
option [8] is OFF, the keypad will only permit access to the areas it controls. For example, the keypad is assigned
area 1 only, and your user access code is assigned areas 1 to 8. If the option is ON, you can access all eight areas
from the keypad. If the option is OFF, you can only access area 1.
NOTE:
By default all users can Regular arm the system.
7.7 Access Control User Options
Option [1]: Access Control
When option [1] is ON, the user can gain access to an access control door when Access Control is enabled in the
system. A user that is not assigned to any partition, but has the Access Control option (Option [1]) enabled, can
now gain access to an access control door by entering a code # (P.I.N.) and then pressing the [ACC] keypad key.
When the option is OFF, the user cannot access an Access Control door.
Option [2]: Can Disarm with Access Card
When option [2] is ON, a User’s Access Control card can unlock and disarm an armed Access Control door. When
option [2] is OFF, follow the settings in option [8] on page 20.
20
EVOHD User Manual
WARNING:
For option [2] to function in the ON position, option [5] “Arm Only” in the User Options must be
disabled (refer to section 7.6).
Option [3]: Card with Extended Unlocked Period
When option [3] is ON, “Extended Unlocked Period” is enabled. “Extended Unlocked Period” refers to the time
period programmed into each Access Control door by your installer that extends the unlocked time of the door.
For example, if your installer sets the Unlocked period of the door to 30 seconds and the Extended Unlocked
Period to 15 seconds, a user access code with “Extended Unlocked Period” enabled will have a total of 45
seconds to pass through the door.
Options [4] and [5]: Arming with Card
Options [4] and [5] define the type of arming when arming with an Access Control card (refer to section 8.2.1).
You can either Regular arm, Stay arm, Force arm, or Disable the Arming with Card feature.
[4] ON, [5] OFF = Regular Arm
[4] OFF, [5] ON = Stay Arm
[4] ON, [5] ON = Force Arm
[4] OFF, [5] OFF = Disable the Arming with Card feature
Option [6]: Add Tolerance Window to Schedule
When option [6] is ON, the Schedule Tolerance Window feature is enabled. This feature extends a user’s
scheduled access period through an Access Control door by the amount programmed by your installer. For
example, if the user’s assigned schedule for the door is Monday to Friday from 9:00 a.m. to 5:00 p.m., and your
installer sets the “Tolerance Window” at one hour, the user with the “Schedule Tolerance Window” enabled will
be able to enter and exit one hour before and after their scheduled time for that door.
Option [7]: Code Follows Schedule
When option [7] is ON, users can use their access codes only during their scheduled hours assigned in step 8 in
section 7.5.1. When the option is OFF, users can use their access codes at any time.
Option [8]: Card to Unlock and Code to Disarm
Option [8] functions only if option [2] in section 7.7 is OFF. When option [8] is ON, a user can use an Access Control
card to unlock an armed Access Control door, however the user must enter a user access code to disarm the
armed area. When option [8] is OFF, a user can gain access to an Access Control door only if the door’s area(s) is
already disarmed.
WARNING:
For option [8] to function in the ON position, option [5] “Arm Only” in the User Options must
be disabled (refer to section 7.6).
EVOHD User Manual
21
Using Access Control
8
Using Access Control
8
8.1 Entering & Exiting
Depending on how your system is installed and on the type of keypad, there are various ways to enter and exit
Access Control doors:
• Present your Access Control card to the reader or the EVO641R or DGP2-641RB
keypad. The system will verify that the card is allowed access according to its
assigned Access Level and Schedule. If it is accepted, the system will unlock the
door. The reader’s light can be programmed by the installer to turn green or
extinguish briefly to indicate that the door can be opened.
• When the motion detector detects movement (Request for Exit), it will unlock the
door to permit passage from inside.
• Enter your user access code on the keypad and press [ACC].
• If the Access Control door is on a “Door Unlocked Schedule”, you may be able to
open Access Control doors without using a user access code or an Access Control
card. Depending on the door’s programming, the door can remain unlocked
during the entire programmed schedule or the door can unlock once a valid
Access Control card is presented to the reader during the schedule and then will
remain unlocked for the remainder of the schedule.
8.2 Arming and Disarming with Card
8.2.1 Arming with Card
•
•
•
•
presented to a door during its assigned Schedule (refer to step 8 in section 7.5.1).
presented to a door within its assigned Access Level (refer to step 8 in section 7.5.1).
programmed to allow arming (options [4] and [5] in (see section 7.7).
assigned to all areas that are assigned to the Access Control door (refer to step 7 in section 7.5.1), or assigned
to at least one of the areas assigned to the Access Control door depending on how your installer has
programmed the Access Control door.
8.2.2 Disarming with Card
To disarm and unlock an Access Control door when the area assigned to it is armed, present your Access Control
card to the reader or EVO641R / DGP2-641RB keypad (door). The Access Control card must be:
• presented to a door during its assigned Schedule (refer to step 8 in section 7.5.1).
• presented to a door within its assigned Access Level (refer to step 8 in section 7.5.1).
• programmed to allow disarming (option [2] in (see section 7.7).
• assigned to all areas that are assigned to the Access Control door (refer to step 7 in section 7.5.1), or assigned
to at least one of the areas assigned to the Access Control door depending on how your installer has
programmed the Access Control door.
8.3 How Access Control Works
To illustrate how Access Control functions, we will use three simple Access Control System examples:
22
EVOHD User Manual
Figure 3 – Example A
Bonnie’s Access Control card is programmed with Access Level 01 and Schedule 01. If she presents her card to
the reader or the EVO641R / DGP2-641RB keypad on Door 02 on Tuesday, August 3 at 3:00 p.m., she will gain
access to the room.
Figure 4 – Example B
If Bonnie presents her card to the reader or the EVO641R / DGP2-641RB keypad on Door 02 on Saturday or on a
Holiday at 3:00 p.m., she will be denied access.
Figure 5 – Example C
If we change Bonnie’s Access Level to 02 and she presents her card to the reader or the EVO641R / DGP2-641RB
keypad on Door 02 on Tuesday, August 3 at 3:00 p.m., she will be denied access.
EVOHD User Manual
23
Trouble Display
9
Trouble Display
9
9.1 Trouble Display
If your system experiences any problems, Trouble(s) [TRBL] to View will appear on the screen, or the TRBL action
light will illuminate. The Trouble Display will only display the troubles that occur in the area(s) to which the
keypad has been assigned. Potential troubles have been sorted into eight groups. Only the troubles which are
relevant to you are listed and described below. If a trouble that is not described or listed below appears, contact
your installer. To view the Trouble Display:
1. Press the [TRBL] button.
The Group Heading with the trouble will appear on the screen. Press the [] and [] buttons to
scroll between the Groups experiencing a trouble.
2.
Press the [NUMBER] of the Trouble you wish to view.
WARNING:
We strongly suggest that if any troubles occur, contact your installer immediately to have
your system serviced.
9.1.1 Group 1: System
[1] AC Failure
The control panel has detected a power failure. This means that your system is running on the
backup battery. If this trouble occurs when your establishment is not experiencing a power failure,
call your installer for repairs.
[2] Battery Trouble
The backup battery is disconnected, needs to be recharged, or replaced.
[5] Bell Absent
The system has detected that the bell or siren is not connected.
9.1.2 Group 2: Communicator
[1] TLM1
The control panel is unable to access the main telephone line.
[2] to [5] Fail to Communicate (1 to 4)
The control panel tried all assigned telephone numbers and failed to contact the monitoring station.
[6] Fail to Communicate PC
The control panel is unable to communicate with the WinLoad software.
9.1.3 Group 5: Zone Tamper
The zone(s) that was tampered with will be displayed on the LCD screen.
9.1.4 Group 6: Zone Low Battery
If a wireless device's battery needs to be replaced, the zone that is assigned to the device will be displayed on the LCD screen.
24
EVOHD User Manual
9.1.5 Group 7: Zone Fault
A wireless device is no longer communicating with its receiver, or a connection or CleanMeTM trouble is occurring with your smoke detectors.
9.1.6 Group 8: Clock Loss
The time and date have been reset to the default. This is the only trouble that we recommend that
you correct. Clock Loss [8] to Set will appear on the LCD screen after you press the [trbl] button or
the [ ] key. Refer to section 10.3 to set the time and date.
9.2 Event Record Display
The Event Record Display will record the user-initiated actions that occurred in your system as well as any
alarms or troubles (i.e. “Access Granted”). You will only be able to view the events that occurred in the area(s)
assigned to your user access code.
Only available on LCD keypads.
To view the Event Record:
1. Enter your [MASTER CODE].
2. Press the [7] button or scroll to view events.
3. If you have access to more than one area, select the area(s) you wish to view.
4. Use the [] and [] buttons to scroll between the events.
5. Press the [CLEAR] button to exit.
Once you have entered Event Record Display mode, you can change the order that the Event Record screens
appear by pressing the [7] button. If you already know the number of the event you want to view, press the
[MEM] button after step 3 above, and then enter the event's number.
EVOHD User Manual
25
Additional Features
10
Additional Features
10
10.1 Programmable Outputs (PGMs)
Your system includes Programmable Outputs (PGMs) that can be programmed by your installer. A PGM triggers
when a predetermined event or series of events occurs in your system. The PGMs can be programmed to reset
smoke alarms, turn on light switches, open or close garage doors and much more. Ask your installer about this
useful feature.
10.2 Keypad Settings
You can modify the keypad settings to suit your needs.
1. Scrolling Speed refers to the amount of time that a message will remain on the screen before moving to the
next message.
2. Backlight refers to the illumination behind the buttons and LCD screen.
3. Contrast refers to how dark or pale characters will appear on the screen.
Enter your [ACCESS CODE]
Press [6]
Press [1]
Scrolling speed:
Choose a number from
0 to 10 (10 is the
slowest)
Press [2]
Backlight:
Choose a number
from 0 to 7 (7 is the
brightest)
Press [3]
Contrast:Choose a
number from 0 to 4
(4 has the most
contrast)
Press [4]
Mute: controls the keypad
beep †
Press [ACC] to enable/
disable ‡
Press [5] ‡
Dim intensity:
Choose a number from 0 to 7
(0 will dim the most after the
delay)
Press [6] ‡
Dim Delay: The delay
will dim after a delay
between 0 (no dimming)
and 255 seconds
[ ] and [ ]
To increase or decrease the numbers
Press [ENTER]
Press [CLEAR] to exit
Press [
]to move to the next setting
*This feature cannot be accessed via One-Touch Buttons (see section 5.6.2).
When keypad mute is enabled, only confirmation, rejection, and key-press beeps are audible.
‡
EVO641 / EVO641R only
†
Figure 6 – Modifying LCD screen settings on LCD Keypads
10.3 Setting Time & Date
To reset the time and date:
1. Enter your [ACCESS CODE] and press the [TRBL] button.
2. Press the [8] button.
26
EVOHD User Manual
3. To change the time, place the cursor under the number you want to change by using the [] button and
enter the time according to a 24-hour clock (i.e. 9 a.m. is 09:00 and 9 p.m. is 21:00).
4. To change the date, place the cursor under the number you want to change and enter the correct date
according to year/month/day.
5. Press the [ENTER] button to save and exit.
10.4 Programming Chime Zones
You can program the keypad to emit a rapid, intermittent beep tone whenever designated zones are opened or
only when opened between certain hours. These zones are referred to as Chime Zones. Your installer can also
program your Chime zones to beep upon closure.
How do I program chime zones?
1. Enter your [ACCESS CODE].
2. Press the [9] key.
3. Press the [1] key to chime a zone. Enter the number corresponding to the zone to be chimed, or use the []
and [] buttons to scroll the list of zones. Press the [ACC] button to chime or unchime the zone that appears
on the screen. Press [ENTER] to save.
OR
Press the [2] button to set the time period a chimed zone will beep. Enter the time that the chimed zone(s)
will start beeping when opened (HH:MM). Enter the time that the chimed zone(s) will stop beeping when
opened (HH:MM).
4. Press [CLEAR] to exit chime programming.
10.5 Panic Alarms
Your system can be programmed to send an alarm to your monitoring station to request help from the police, a
medical facility, the fire department, or anyone you wish when you press a predetermined combination of
buttons. To generate a panic alarm, simultaneously press and hold the button combinations displayed in Table
on page 27. Your installer can program the alarm to be either silent or audible.
Table 7: Panic Buttons
Panic Alarm Types
Buttons to be pressed and held simultaneously
Emergency Panic
Press & hold the [1] and [3] buttons
Auxiliary Panic
Press & hold the [4] and [6] buttons
Fire Panic
Press & hold the [7] and [9] buttons
10.6 Quick Function Buttons
You will only need to use the Quick Function Buttons upon your installer’s or monitoring station's request. Only
the System Master Code or user access codes with the Master feature enabled will be able to access these
functions.
To access the Quick Function Buttons:
EVOHD User Manual
27
1. Enter your [ACCESS CODE]
2. Press the [0] button.
3. Press the:
[STAY] to send a test report to the monitoring station.
[FORCE] to call the WinLoad software.
[ARM] to answer the WinLoad software.
[DISARM] to cancel communication with the WinLoad software.
28
EVOHD User Manual
VDMP3 Plug-In Voice Dialer
VDMP3 Plug-In Voice Dialer
11
11
The VDMP3 is a voice-assisted module that can be programmed to call up to 8 telephone numbers in the event
of an alarm. You can also call the VDMP3 from an outside line, enabling you to arm or disarm the system as well
as activate up to 8 PGMs.
11.1 Calling the VDMP3 (outside line)
If your outside line is connected to an answering machine:
1. From an outside line, dial the telephone number to which the VDMP3 is
connected.
2. When the line rings, hang up the telephone.
3. Dial the telephone number again within the time limit set by your
installer.
4. When the VDMP3 answers the line, you are prompted to enter your
access code.
5. Options are given to arm/disarm (1) and control features (PGMs) (2).
If your outside line is not connected to an answering machine:
1. From an outside line, dial the telephone number to which the VDMP3 is
connected.
2. When the VDMP3 answers the line, you are prompted to enter your
access code.
3. Options are given to arm/disarm (1) and control features (PGMs) (2).
11.2 Receiving a Call From the VDMP3 (alarm in system)
When the VDMP3 calls because of an alarm in the system, the option is given to disarm the system or
disconnect (##).
If you hang up without disarming or disconnecting, the VDMP3 calls the next telephone number on its list (see
Telephone Numbers in VDMP3 Setup Instructions).
EVOHD User Manual
29
30
EVOHD User Manual
Testing and Maintenance
12
12.1 Burglar Alarm Testing
Two people are needed to complete this test. One person will watch the screen on the keypad while the other
person walks around the protected areas and opens the zones (i.e. opens the doors and windows that are
protected, walk in the path of the motion detectors, etc.). The screen will display the opened zones, but if a
zone does not register, contact your installer.
12.2 Fire Alarm Testing
Do NOT use an open flame or burning materials to test your fire detection devices. Your installer will provide
details on the best way to test your system.
12.3 System Maintenance
Under normal use your system requires no maintenance other than regular testing. We recommend that your
installer change the battery every three years.
12.4 System Test
Speak to your installer before conducting a System Test since the system must be programmed to respond to
the test instructions. It is normally recommended that you conduct the system test once a week, but contact
your installer for instructions concerning your particular system.
To conduct the system test:
1. Call your monitoring station to advise them that you are testing your system.
2. Enter your [ACCESS CODE].
3. Press the [8] button.
The system will test all its connections and can send a report to your monitoring station. If the system detects a
problem, the Trouble Display will show on the keypad or touchpad screen. Call your installer for repairs if any
troubles occur.
EVOHD User Manual
31
Fire and Burglar Alarms
13
Fire and Burglar Alarms
13
13.1 Standard Fire Zone
During a fire alarm, the bell/siren emits an intermittent sound (BEEP-BEEP-BEEP) until silenced or reset. If the zone
is a Standard Fire Zone, your system can immediately send an alert to your monitoring station.
The CMS will try to contact you. If they cannot reach you for any reason, for example they get a busy signal, the
procedure is to dispatch the proper authorities.
To disarm a false alarm:
1. Enter your [ACCESS CODE] on the keypad.
2. Call your monitoring station quickly to advise them of the false alarm.
WARNING:
The Fire Zone may reset itself once the problem has cleared. If it does not, simultaneously
press and hold the [CLEAR] and [ENTER] buttons for two seconds.
13.2 Delayed Fire Zone
If the zone is a Delayed Fire Zone, there is an automatic delay before your system contacts your monitoring
station. Refer to Figure 7 on page 33 to prevent unnecessary reporting of false alarms.
If the fire alarm is accidentally triggered:
1. Press the [CLEAR] button within 30 seconds of the alarm.
2. Clear the problem from the area (i.e. clear the smoke from around the smoke detector).
3. If the problem remains after 90 seconds, the alarm will sound again. Press [CLEAR] again.
4. The system will delay reporting the alert for another 30 seconds.
NOTE:
If you are unable to cancel the false alarm, your system will send an alert. Call your monitoring station
to advise them of the false alarm.
WARNING:
The Fire Zone may reset itself once the smoke has cleared. If it does not, simultaneously press
and hold the [CLEAR] and [ENTER] buttons for two seconds or speak to your installer.
13.3 Fire Safety Tips
How should you prepare in case of a fire in your home or business?
•
•
•
•
•
•
•
•
Remind everyone to escape first, and then call for help.
Develop a fire escape plan and designate a meeting place outside.
Practice the escape plan frequently.
Plan two ways to escape from every room, if possible.
Practice feeling the way out with eyes closed.
Instruct everyone never to stand up during a fire, always crawl under the smoke and keep mouths covered.
Instruct everyone never to return to a burning building for any reason; it may cost them their life.
Check smoke alarms regularly. Working smoke alarms dramatically increase everyone's chances of surviving a
fire.
32
EVOHD User Manual
Figure 7 – Delayed Fire Zone
13.4 Minimizing Home Fire Hazards
How can you avoid the three most common causes of fires at home?
• Never leave cooking food unattended. It’s the leading cause of fire injuries. Cooking fires often result from
unattended cooking and human error, rather than mechanical failure.
• Stay alert when smoking. Careless smoking is the leading cause of fire deaths. Smoke detectors and
smoulder-resistant bedding and upholstered furniture are significant fire deterrents.
• Maintain your heating system. Faulty heating systems are the second leading cause of residential fires.
13.5 Home Fire Warning System
Household fires are especially dangerous at night. Fires produce smoke and deadly gases that can overcome
occupants while they sleep. To warn against fire, install smoke detectors outside each separate sleeping area in
the immediate vicinity of the bedrooms and on each additional story of the family living unit, including
basements.
13.6 Burglar Alarm
If your armed system is breached, the burglar alarm devices specific to your system will be triggered. The
feedback will vary depending on the type of keypad used. If your keypad is in Normal Mode:
• In Alarm will appear on LCD screen.
• Bell or siren may be activated.
• The keypad may beep. The MEM action light will illuminate.
WARNING:
In case of a burglar alarm, leave the premises and call the police station from a safe place.
EVOHD User Manual
33
Basic Operation of the TouchPad TM50
14
Basic Operation of the TouchPad TM50
14
The touchpad is a versatile input device that lets you, the master user, along with other users, manage your
system. This touchpad has a lot of the same capabilities as your Insight App. Management and configuration of
the system through the touchpad can be restricted to users of your choice.
This section will break down the functionality of the touchpad into the following groupings.
• Main screen direct access
• Security Functions
• Control Devices
• Add-ons
• Personalize
• User codes
• Advanced
• System Settings
The touchpad home screen has the following control options directly from the home screen.
14.1 Touchpad Main Screen
Areas
Arm /Disarm
Slide Show on/
off
Panic
Emerency
Troubles
Alarm
Memory
Troubles
Home
Screen
Zone
Bypass
Enter Code
Event Log
Read Log
Select Zone
Select Zones to
bypass
Set parameters for zones
Label, Number, Status,
Chime, and Linkd to Area
Figure 8 – Main Screen Direct Access
The Areas button and Panic button need to be added to the home screen by your installer. The slide show is
accessed with the icon or through the menu => Personalize => slide show.
34
EVOHD User Manual
14.2 Touchpad Security Functions
Home
Screen
Security
Functions
Arm /
Disarm
Bypass
Zones
Menu
Select Arming
Method
Select
Zone
View System
Status
View
Troubles
View
Areas
Auto
Arm
View
Zones
Zone
Chiming
Select
Zone
View
Alarm
Memory
View Event
Log
Chime
Period
Chime
Trigger
Figure 9 – Security Functions
14.3 Touchpad Control Devices
Home screen
Smoke Reset
Menu
Control
Devices
Utility Keys 1 to 8
Utility Keys 1 to 8
Utility Keys 1 to 8
Figure 10 – Control Devices
14.4 Touchpad Add-on Functions
Home screen
Menu
SpotOn Locator
Add-on
One Screen
Monitoring
Figure 11 – Add On Functions
EVOHD User Manual
35
14.5 Touchpad Personalize
Set Time/
Date
Home screen
Title Bar Info
Menu
Show/Hide
Temperature
measurement
Home Page
Home Page
Type Default /
Residential
Personalize
Alarm Clock
Set alarm Day and
time
Languages
Select the language
Slide Show
Area/Zone Labels
Figure 12 – Personalize
14.6 Touchpad User Codes
Home screen
Menu
User Codes
Add User
Edit User
Delete User
Figure 13 – User Codes
36
EVOHD User Manual
14.7 Touchpad Advanced Functions
Home
screen
Menu
SMS setup
Product
info
Special
Functions
Advanced
Send test
Report
Stop
Communication
Call PC software
Calibrate
Screen
Answer PC
Software
Calibrate
sensors
upgrade
Figure 14 – Advanced Functions
14.8 Touchpad System Security
Home screen
Menu
Volume /
Mute
System
Settings
Control
Devices
Zone Chiming
Time & Date
Display
Settings
Warning
Sounds
Area/zone
labels
Clean Screen
Customize
home page
Permissions
Figure 15 – System Settings
EVOHD User Manual
37
Appendix: A
Hebrew Special Characters
Refer to the following tables when programming the user labels of a Hebrew LCD keypad. Instead of using Table on
page 16 and Table 6 on page 18, use Tables 9 and 10 below. Refer to section 7.3 on page 16 for information on
programming user labels.
Table 8: Hebrew Keypad Letter Assignment
Table 9: Hebrew Special Characters Catalogue
38
032
048
064
080
096
112
160
176
192
208
224
240
033
049
065
081
097
113
161
177
193
209
225
241
034
050
066
082
098
114
162
178
194
210
226
242
035
051
067
083
099
115
163
179
195
211
227
243
036
052
068
084
100
116
164
180
196
212
228
244
037
053
069
085
101
117
165
181
197
213
229
245
038
054
070
086
102
118
166
182
198
214
230
246
039
055
071
087
103
119
167
183
199
215
231
247
040
056
072
088
104
120
168
184
200
216
232
248
041
057
073
089
105
121
169
185
201
217
233
249
042
058
074
090
106
122
170
186
202
218
234
250
043
059
075
091
107
123
171
187
203
219
235
251
044
060
076
092
108
124
172
188
204
220
236
252
045
061
077
093
109
125
173
189
205
221
237
253
046
062
078
094
110
126
174
190
206
222
238
254
047
063
079
095
111
127
175
191
207
223
239
255
EVOHD User Manual
Appendix: B
Russian Special Characters
Refer to the following tables when programming the user labels of a Russian LCD keypad. Instead of using Table on
page 16 and Table 6 on page 18, use Tables 11 and 12 below. Refer to section 7.3 on page 16 for information on
programming user labels.
Table 10: Russian Keypad Letter Assignment
Table 11: Russian Special Characters Catalogue
EVOHD User Manual
032
048
064
080
096
112
160
176
192
208
224
240
033
049
065
081
097
113
161
177
193
209
225
241
034
050
066
082
098
114
162
178
194
210
226
242
035
051
067
083
099
115
163
179
195
211
227
243
036
052
068
084
100
116
164
180
196
212
228
244
037
053
A069
085
101
117
165
181
197
213
229
245
038
054
070
086
102
118
166
182
198
214
230
246
039
055
071
087
103
119
167
183
199
215
231
247
040
056
072
088
104
120
168
184
200
216
232
248
041
057
073
089
105
121
169
185
201
217
233
249
042
058
074
090
106
122
170
186
202
218
234
250
043
059
075
091
107
123
171
187
203
219
235
251
044
060
076
092
108
124
172
188
204
220
236
252
045
061
077
093
109
125
173
189
205
221
237
253
046
062
078
094
110
126
174
190
206
222
238
254
047
063
079
095
111
127
175
191
207
223
239
255
39
Appendix: C
Greek Special Characters
Refer to the following tables when programming the user labels of a Greek LCD keypad. Instead of using Table on
page 16 and Table 6 on page 18, use Tables 13 and 14 below. Refer to section 7.3 on page 16 for information on
programming user labels.
Table 12: Keypad to Letter Insertion
Key
Press key once
[1]
A
[2]
[3]
Press key three
times
Press key twice
B
G
D
E
Z
H
Q
I
[4]
K
L
M
[5]
N
O
[6]
P
R
S
[7]
T
U
F
[8]
C
Y
W
Table 13: Greek Special Characters Catalogue
40
016
032
048
064
080
096
112
128
144
160
176
192
208
224
240
017
033
049
065
081
097
113
129
145
161
177
193
209
225
241
018
034
050
066
082
098
114
130
146
162
178
194
210
226
242
019
035
051
067
083
099
115
131
147
163
179
195
211
227
243
020
036
052
068
084
100
116
132
148
164
180
196
212
228
244
021
037
053
A069
085
101
117
133
149
165
181
197
213
229
245
022
038
054
070
086
102
118
134
150
166
182
198
214
230
246
023
039
055
071
087
103
119
135
151
167
183
199
215
231
247
024
040
056
072
088
104
120
136
152
168
184
200
216
232
248
025
041
057
073
089
105
121
137
153
169
185
201
217
233
249
026
042
058
074
090
106
122
138
154
170
186
202
218
234
250
027
043
059
075
091
107
123
139
155
171
187
203
219
235
251
028
044
060
076
092
108
124
140
156
172
188
204
220
236
252
029
045
061
077
093
109
125
141
157
173
189
205
221
237
253
030
046
062
078
094
110
126
142
158
174
190
206
222
238
254
031
047
063
079
095
111
127
143
159
175
191
207
223
239
255
EVOHD User Manual
Index
A
Access Codes
Deleting 18
Labelling 16
Programming 18
System Master 15
User 15
Access Control 20
Entering & Exiting 22
Access Control User Options
Access Control 20
Add Tolerance Window to Schedule 21
Arming with Card 21
Can Disarm with Access Card 20
Card to Unlock and Code to Disarm 21
Code Follows Schedule 21
Extended Unlocked Period 21
Add Tolerance Window to User Schedule 21
Alarm Clock 36
Alarm memory 35
Alarm Memory Display 14
Alarm,Testing 31
Ambulance 34
Area Access, in User Options 20
Area Display 9
Arm 34, 35
Arming
Automatic Arming 12
Force Arming 10
Instant Arming 10
Keyswitch Arming 12
Regular Arming 10
Stay Arming 10
with Card 22
Auto-Arming
EVOHD User Manual
41
No Movement Auto-Arming 13
Timed Auto-Arming 12
B
Battery
Disconnected 24
Low, in a Zone 24
Beep Tones
Confirmation beep 7
in Opened or Closed Zones, see Chime Zones
Rejection beep 7
Bell Disconnected 24
Brightness 37
Burglar Alarms 33
Buttons
One-Touch 12
Quick Function 27
Bypass 34
Bypass Recall 11
Programming 11
Bypass zone 35
C
Card, Access Control
Arming with 22
Disarming with 22
Characters, Special 18
Chime Zones 27
Chiming 35
Clean screen 37
Clock 36
Clock, Set Time and Date 26
Code Follows Schedule 21
Configuration permissions 37
Copy User Options 15
D
Date, Set Keypad 26
Date, Set Touchpad 37
Deactivating a Security System 14
42
EVOHD User Manual
Delay Timer
Entry 14
Exit 10
Delayed Fire Zone 32
Deleting User Access Codes 18
Disarm 34, 35
Disarming
Armed System 14
with Card 22
Display
Alarms In Memory 14
User Actions in Memory 25
Display settings 37
Duress, in User Options 20
E
Emergency Buttons 27
Entering and Exiting, Access Control Doors 22
Entry Delay Timer 14
Erasing User Access Codes 18
Event log 35
Event Record Display 25
Events 34
Exit Delay Timer 10
Extended Unlocked Period 21
F
Fire 34
Delayed Fire Zone 32
Minimizing Home Fire Hazards 33
Safety Tips 32
Standard Fire Zone 32
Warning System 33
Fire Alarm, Testing 31
Force Arming 10
H
Home page 36
Home Screen 36
EVOHD User Manual
43
I
Ignoring Zones when Arming, see Bypass Programming
instant arm 35
Instant Arming 10
K
Keypad, LCD
Buttons 7
Letter Assignment 16
Lights 7
Messages 7
Settings 26
Keyswitch Arming 12
L
Language select language 36
Log 34
Log for events 35
M
Master Code 15
Master Feature, in User Options 20
Memory alarm 35
Memory of alarms 34
Monitoring 35
Mute 37
N
No Movement Auto-Arming 13
O
One Screen Monitoring 35
One Touch Button for the DGP-641BL/RB and the DGP-648 12
One-Touch buttons 12
Outputs, Programmable (PGM) 26
P
Panel brightness 37
Panic Alarms 27
Panic button 34
Permissions to configure touchpad 37
Pictures 34
44
EVOHD User Manual
Police 34
Power Failure, see Trouble
Programmable Outputs (PGM)
26
Programming
Chime Zones 27
User Access Codes 18–20
Q
Quick Function Buttons
Answer Winload Sofware 28
Call Winload Software 28
Cancel Communication with Winload Software 28
Send Test Report 28
R
Recall, Bypassed Zones 11
Regular Arming 10
Request for Exit 22
S
Safety Tips, Fire 32
Schedule
Code Follows 21
Schedule Tolerance Window, see Add Tolerance to User Schedule
Set date 36
Set Time 36
Set Time and Date 36, 37
Siren Disconnected 24
Slide Show 34, 36
Slides 34
Smoke detector 35
Smoke detector reset 35
Special Characters 18
Special Characters, Greek 40
Special Characters, Hebrew 38
Special Characters, Russian 39
Special Function Keys 17
Standard Fire Zone 32
Status, View 35
EVOHD User Manual
45
Stay Arm 35
Stay Arming 10
System Master Code 15
System Test 31
T
Tampered Zones 24
Temperature sensing 36
Testing and Maintenance
Burglar Alarm 31
Fire Alarm 31
System Maintenance 31
System Test 31
Time, Set 26
Time, set 37
Timed Auto-Arming 12
Timer
Entry Delay 14
Exit Delay 10
Touchpad Add-ons 35
Touchpad Advanced Functions 37
touchpad brightness 37
Touchpad Control Devices 35
Touchpad main screen 34
Touchpad Personalize 36
Touchpad Reset Smoke Detector 35
Touchpad rest smoke detector 35
Touchpad Security functions 35
Touchpad System Security 37
Touchpad User Codes 36
Trouble
AC Failure 24
Battery 24
Bell/Siren Disconnected 24
Clock 25
Communicator 24
Fail to Communicate 24
Fail to Communicate PC 24
46
EVOHD User Manual
Low Battery, Zone 24
System 24
TLM1 24
Zone Fault 25
Zone Tampering 24
Troubles 34, 35
U
Unlocked Period, Extended 21
User Labels 16
User Options
Access Control, see Access Control User Options
Area Access 20
Arm Only 20
Bypass 20
Copy 15
Duress 20
Force Arm 20
Master Feature 20
Programming 20
Stay & Instant Arm 20
User Settings 19
V
VDMP3 Plug-In Voice Dialer 29
View memory 35
View Status 35
View troubles 35
Viewing
Alarms In Memory 14
User Actions in Memory 25
Volume 37
Z
Zone Chiming 35
Zone Labels 36
Zones 34
EVOHD User Manual
47
whole
Paradox team
team wishes
youyou
a successful
and easy
TheThe
whole
Paradox
wishes
a successful
andinstallation.
easy installation.
We
hope
this
product
performs
to
your
complete
satisfaction.
We hope this product performs to your complete satisfaction.
Should
youhave
haveany
any questions
or or
comments,
pleaseplease
contactcontact
us.
Should
you
questions
comments,
us.
For support, please contact your local distributor, or dial 1-800-791-1919
For (in
support,
please contact your local distributor, or dial +1-450-491-7444,
North America) or +1-450-491-7444 (outside North America), Monday
Monday
to
Friday,
from
8:00
5:00 p.m. EST.
to Friday, from 8:00
a.m. to
8:00a.m.
p.m.to
EST.
YouYou
may
also
e-mail
us
at
[email protected]
may also e-mail us at [email protected]
Additional
canbebe
found
at PARADOX.COM
Additionalinformation
information can
found
at PARADOX.COM
Printed in Canada
EVOHD- EU00
paradox.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement