NSS Cataglog and Brochures

NSS Cataglog and Brochures
Here’s How To Schedule a Demonstration, Place an Order, or Get More Information
Integrity at work.®
To schedule a demonstration at your facility, or to place an order for NSS equipment,
contact your local NSS Distributor. To find the distributor nearest you, please
call NSS at 800-677-1663 or visit our web site at www.nss.com.
NSS®, Wrangler®, and “Pig”® are registered trademarks of
NSS Enterprises, Inc. All rights reserved.
Twister™ is a trademark of HTC, Inc. All rights reserved.
Appearance and specifications of machines are subject to
change without notice.
Availability of specific product models varies by country.
©2009, NSS Enterprises, Inc., Printed in the U.S.A.
#9090013 REV I 2/09 2009-2010
Printed on paper that contains
30% recycled post-consumer fiber.
NSS Enterprises, Inc.
3115 Frenchmens Road
Toledo, OH 43607-2958
USA
(800) 677-1663
(419) 531 3761 (fax)
[email protected]
www.nss.com
WARRANTY
Effective for machines purchased after May 1, 2009.
NSS® Enterprises, Inc. Limited Warranty
NSS Enterprises, Inc. (NSS) warrants its new machines against defects in material and workmanship under normal use, service and
maintenance (defined in the NSS Operation and Maintenance Manuals) for the warranty period as detailed below. This warranty is limited to
machines and products that are purchased from an NSS Authorized Distributor or directly from NSS and is limited to the original end-user. Under this
warranty, NSS will repair or replace, at its option, any covered part which is found defective in material or workmanship during the applicable warranty
term. This repair or replacement shall only be performed by an NSS Authorized Distributor or Service Center. All shipping charges for replacement
parts or repaired machines will be the responsibility of the original end-user. When requested, machines and/or parts must be returned to NSS for
inspection to obtain this warranty. NSS reserves the right for final determination of warranty coverage.
The start date of this warranty is the purchase date by the original end-user from an NSS Authorized Distributor or directly from NSS, subject to proof
of purchase. If proof of purchase is not available, the warranty begins six months from the date the machine was shipped from the factory. Parts
repaired or replaced under this warranty are warranted for the remainder of the original warranty period. When covered, a maximum of 4 hours travel
time will be allowed. When out of the continental USA, Labor, Freight and Travel may have different considerations.
NSS will not be liable for any other or additional damages, including but not limited to indirect or special consequential damages arising out of or in
connection with the furnishing, performance, use or inability to use the machine. The buyer agrees and understands that the remedies provided under
this limited warranty are the sole and exclusive remedies available to the buyer. NSS reserves the right to change its warranty policy without notice.
This warranty shall not apply to:
1. Damage incurred during shipment.
2. Any product that has been subject to misuse, abuse, negligence, overloading or accident.
3. Improperly used products or use of the product for other than its intended purpose.
4. Failures due to lack of mandatory maintenance as described in NSS Operation and Maintenance Manuals, Videos and/or Wall Charts.
(e.g., lack of scheduled lubrication or inadequate flushing of chemical solutions.)
5. Any machine modified from its original design (unless authorized by NSS) or repair services performed by non-authorized service centers.
6. Damage or failure resulting from the use of corrosive or incompatible chemicals.
7. Replacement of ordinary wear items including but not limited to: bumpers, belts, carbon motor brushes, electrical components exposed to
moisture, filter bags, hoses, casters, wheels, gaskets, seals, cords, circuit breakers, switches, check valves, solenoids, pumps, squeegee
blades, M-1 fans and fan hoods, and shoes on NSS manufactured cast aluminum tools.
Product
Polyethylene Roto-Molded Tanks & Components
NSS Manufactured Cast Aluminum Tools
Tools and Accessories
On-board Battery Chargers
Batteries
Service Parts for out-of-warranty machines
Autoscrubbers
Champ and Wrangler Series
Burnishers
Charger 2500 & 1500 (cord electric)
Charger 2716, 2717 and 2022 (battery)
Mustang 1500, Galaxy 1500
Commander (Propane)
Floor Machines
Thoroughbred Series
Maverick, Mustang, and Galaxy Series
Sweepers
Manta RS 36, Sidewinder Series
Wet/Dry Vacuums
BP Ranger Series
Colt Series
Bronco Series
Carpet Vacuums
Model M1 “Pig”
Pacer 30, Outlaw B/V, Pacer PB
Pacer 112/115 UE
Pacer 214/218 UE
Carpet Extractors, Spotters and Dryers
Pony 20 SCA, Stallion 8 SC, Stallion 12 SC
Aero Plus
Predator Series
Pressure Washers
AquaForce Series
Parts
Labor
Travel
10 Years
10 Years
1 Year
2 Years
1 Year
90 Days
1 Year
1 Year
6 Months
Exceptions
1 Year
1 Year
6 Months
1 Year
3 Years
1 Year
6 Months
7 Years
3 Years
3 Years
3 Years
1 Year
1 Year
1 Year
1 Year
6 Months
6 Months
6 Months
2 Years parts on Engine, Battery, Fuel System
7 Years
3 Years
1 Year
1 Year
6 Months
1 Year parts for machines with additional weights
1 Year
1 Year
7 Years
3 Years
1 Year
1 Year
1 Year
1 Year
6 Months
7 Years
3 Years
2 Years
1 Year
1 Year
1 Year
1 Year
1 Year
6 Months
3 Years
3 Years
1 Year
1 Year
1 Year
1 Year
1 Year
1 Year
Does not include shoes
Battery mfr’s warranty, contact NSS for referral
6 Months travel for Manta RS 36
1 Year parts on Pacer PB Battery Charger
Includes Belt
2 Years parts on Motors and PC Board
If a problem with NSS equipment develops during the warranty period, first contact your NSS Authorized Distributor or Service Center.
NSS Enterprises, Inc., 3115 Frenchmens Road, Toledo, Ohio 43607-2958 USA (419) 531-2121 www.nss.com Warranty Sheet #9090034 Rev 05/09
NSS European Distribution Centre, Unit 11, Pinfold Trading Estate, 55 Nottingham Road, Stapleford, Nottingham NG9 8AD England (44) 0115 939 1568
Page 19
ABOUT NSS
TOOLS & ACCESSORIES
Trusted for Nearly a Century
Bare Floor Tool Kit
®
Since 1911, NSS has been helping make the world a
cleaner, healthier, and more comfortable place. As the
only privately owned and operated full line floor care
equipment company in the United States, NSS provides
high quality, heavy-duty commercial and industrial floor
care equipment in the US and 60 countries around the
world.
NSS’s principle-centered leadership has resulted in a
stable enterprise, which operates with core values of
integrity, friendship, and goodwill. These strong beliefs
are reflected in the way we do business every day.
Product Solutions to Meet Real World Demands
Floor & Lite High-Up Kit
Gulper Tool
Squeegee/Bristle Flip Tool
At NSS, we don’t just produce products—we work to
provide our customers with solutions and systems that
deliver real world value. It all begins with our product
development process.
We spend time with our customers and end-users
to understand their issues and needs. We meet with
them, interview them, and observe them in their work
environment. Based on this input, prototype machines
are created and field-tested by real operators. With new
input from the field-testing, we redesign and refine, and
field-test again. The end result is innovative, functional
products which are easy to use and easy to service.
Problem-free Equipment Built to Last
NSS has always employed the philosophy of design
simplicity—uncomplicated solutions that avoid
unnecessary, trouble-prone gadgetry.
Tools & Accessories
Like our machines, NSS tools and accessories are abuseresistant and built to last. Attention to detail, functionality,
and user-friendly operation are hallmarks of our wide array of
tools. Our offering is extensive—you will find unique tools for
specialty applications that can’t be found anywhere else.
Carpet Tools
Just pick up an NSS tool—feel its heft in your hands—to
see the quality difference. In fact, many of our tools are
formed with cast-aluminum bodies and brass fittings and
connectors.
A key feature of NSS tools is their curved uniflow design,
which maximizes airflow and pick-up. Our attention to
ergonomic principles means that NSS tools are designed for
safe and efficient use.
At NSS, we have over 25 tool kits designed to meet different
customer needs. Wet or dry, for ceilings, walls, or floors, we
have a the right kit to help you get your job done more easily,
more quickly, and more safely.
We have confidence in our tools. That’s why many are backed
by a 10-year warranty, which speaks volumes about their life
expectancy and quality of construction.
Ecostrip pads allow damp stripping floors without chemicals.
Just attach to your favorite NSS scrubber and remove the
yellow top coat with just water.
Page 18
That’s why our machines last longer and need fewer
repairs. When repairs are needed, design simplicity
makes NSS machines easy for technicians to service.
The result for our customers is significantly longer
equipment life, less downtime for service and repairs,
and lower machine lifecycle costs. When you purchase
NSS equipment, you are truly making an investment in an
asset that will be around for years to come.
Reliable Delivery and Exceptional Support
Pipe, Wall, and
Shelf Brushes
Super Flex Vacuum Hose
Extended Length Wand
Getting the right equipment where and when it is needed
is critical. That’s why we are diligent to ensure reliable,
on-time, complete delivery of orders.
ISO 9001 certified, our manufacturing facility in Toledo,
Ohio maintains a large inventory of machines that are
ready for shipment. NSS also maintains warehouses in
Connecticut, California, the United Kingdom, the Middle
East, and Asia. Most parts are shipped within 24 hours.
Once our products are in your hands, NSS stands
behind them fully—with highly-trained customer service
personnel, technical support, training seminars, and a
comprehensive warranty. Over 400 Distributors and
Service Centers are authorized to provide field service in
North America.
Do No Harm™
Ecostrip Pads
For more details about NSS or how you can benefit from
our product solutions, call 800-677-1663, or visit us at
www.nss.com.
CARPET EXTRACTORS
NEW PRODUCT
Charger Series
Battery Burnishers
Two years ago, we introduced the Charger 2717 DB burnisher, our 27” battery burnisher, which
proved popular among big box retailers. We followed that success the following year with the
Charger 2022 DB, a 20” battery burnisher. At the same time, we introduced our Sulky option,
which was awarded the ISSA 2008 Product Innovation Award at the annual trade show in Las
Vegas.
Charger 2022 ABLT
Easier to Service with Enhanced Durability
• Electronic components are grouped behind the back panel for easy access.
• The digital readout can display service codes to speed problem diagnosis.
• The heavy-duty roller chain and sprockets drive system is extremely reliable.
Greener
• The recyclable 12-gage steel body minimizes waste.
• An enhanced Vac-Trac system captures more pad dust and finish powder.
Even Better Shine
• For a uniform, high-gloss shine, the pad speed and pad pressure are consistently maintained.
• Rugged three-tank carpet spotter
• 100 PSI pump powers solution deep into the nap
• Dual 1-gal/3.8-l solution tanks—separate solution and rinse water
• Dual 2-stage 1.25 HP vacuum motors
• 2.5-gal/9-l detachable recovery tank
• Solid-state circuitry for trouble-free operation
• 55 PSI pump for penetrating stubborn spills
• CXH 100 includes a heating
element; CXC 100 uses cold
water
• Also ideal for upholstery and car detailing
Aero Plus
• Three speeds for maximum drying
performance
• Four positions for drying carpets,
bare floors, upholstered furniture,
and ceilings
• Reduces drying times by up to 50
percent
• Durable rotocast polyethylene
body
• Stacks three high for greater airflow
and efficient storage
For consistent, quiet and safe battery burnishing, the Charger Series is a clear leader in its class.
Greater Convenience
• No operator adjustment is required for a consistent, high-gloss shine.
• The head assembly flips up 90° for more compact storage.
• Pad changes can be made from a standing position.
• Its offset body keeps the operator centered in the workpath for greater visibility.
• A digital readout displays remaining battery charge life.
Spots away
Faster drying—floor to ceiling
To help fit the Charger 2022 ABLT into your budget, we’ve introduced a
24-Volt, 225 AH system. With two fewer batteries, we can make the machine
smaller while keeping everything the same where it really counts... on the floor. We’ve also
optimized the wheel position to make the machine easy to maneuver. To help fit the Charger
2022 ABLT to your operators, we have added an adjustable handle to allow comfortable,
ergonomic operation.
Enhanced Productivity
• The optional sulky attachment provides greater productivity. (DB models only)
• Chargers are available in 20 and 27-inch widths.
Predator CX3
Powerful and
maneuverable
• 8-gal/30-l solution and recovery tanks
Building On Success
This year, we’re taking everything that people love about the Charger burnisher series
and putting it into a value-priced machine. The new Charger 2022 ABLT is a 20”
burnisher designed to fit into the tightest budget. First, and most
importantly, the Charger 2022 ABLT features the same steady-speed
motor controls as the other Charger models. The controller monitors
the motor voltage and keeps it constant giving you the same pad
speed and pressure through the whole job. Second, just like the
other Charger models, the Charger 2022 ABLT has a flip-up head that
allows for ergonomically-correct standing pad changes and easy storage
in small closets.
8-Gallon Predators
Charger 2022 DB
• Optional wheel and folding
transport handle available
PRESSURE WASHERS
NSS’s AquaForce pressure washers include hand-carry
models, cart electrics, and gasoline-powered units. Each
is an exceptional value providing power, ease of use, and
durability.
1500A and 1500 AHT
Electric hand-carry pressure
washer – cold and hot
water models
• 2 HP electric motor • 1500 PSI of water pressure
• Delivers 2 gal/7.5 L per minute
• Ground fault interrupter for
operator safety
• 1500 AHT model accepts water up to 180 degrees F
1000MXDE
25006HX
Electric pressure washer
with cart – hot water
models
Gas-powered mobile pressure
washer – cold water
• 1000 PSI of water pressure
• 2500 PSI of water pressure
• Delivers 2.2 gal/8 L per
minute
• Delivers 3.2 gal/12 L per minute
• Features dual chemical
injection for tough jobs
• Thermal relief valve
• 3-gallon /11-L chemical tank
• Powerful CAT pump; accepts
water up to 180 degrees F
2000GCX
1500AMXDE
Gas-powered mobile pressure
washer – cold water
Electric pressure washer
with cart – cold water
• 2 HP motor
• 1450 PSI of water pressure
• Delivers 2 gal/7.6 L per
minute
• Dual chemical injection
Page 4
• 6.5 HP Honda gas engine
• 5 HP Honda gas engine
• 2000 PSI of water pressure
• Axial pump delivers 3 gal/
11.4 L per minute
• 3-gal chemical injection tank
• Insulated trigger gun, wand and 40-foot hose included
Page 17
CARPET EXTRACTORS
NEW PRODUCT
Pony 20 SCA
Powerful, large area
automatic
• 22-inch/56-cm cleaning path
• 20-gal/76-l solution and recovery tanks
• 100 PSI solution pump for deep cleaning
• Powerful 3-stage vacuum motor with float shut-off
• Variable speed propulsion
system
• Built-in spray wand
Carpet Extractors
NSS extractors keep your carpets looking their best. There
is a machine to meet every carpet cleaning need, each
constructed for maximum performance, durability, and
long life.
Stallion 12 SC
Galaxy 1500
Cord-Electric Burnisher
Economical High Gloss Shine
The Galaxy 1500 is a durable, economical cord-electric burnisher that
performs with the high-quality hard floor efficiency you’ve come to expect
from NSS.
The unique features of the Galaxy 1500 set it apart from other economical
burnishers. The chrome-plated handle prevents corrosion, and the chromeplated deck resists the effects of harsh floor finishes and chemicals. Built-in
transport wheels at the rear of the unit assist in transporting the Galaxy
1500 in and out of buildings and vehicles. And an ergonomic handle
adjustment allows the operator to set the handle height for comfort.
As with other Galaxy models, the Galaxy 1500 features our patented twopart packaging system, allowing shipment via small parcel service.
Excellent mid-size
extractor
The Pony 20 SCA, Stallion 12 SC, and Stallion 8SC selfcontained extractors are the choice for fast, effective
cleaning. These NSS automatics complete your job in half
the time of a tank extractor. Their tank-over-tank design
improves sight lines and keeps the machines balanced from
job start to finish. Both machines can be used with optional
upholstery and stair cleaning tools and a 3-jet wand.
• 18-inch/46-cm cleaning path
• 12-gal/45.5-l solution and
dual 6-gal recovery tanks
• 100 PSI solution pump cleans deep
• Powerful 3.5 HP, 2-stage
vacuum motor
The Predator CX 300 HP is NSS’s deluxe, dual pressure hot
water tank unit. Four additional models of Predator tank
extractors let you choose hot- or cold-water cleaning in two
different size units. The handy Predator CX3 features a third
tank for clean rinse water. For floor applications to ceiling
applications, the Aero plus dryer speeds drying time by as
much as 50 percent.
• Low-flow solution switch
uses less water, conserving
water without sacrificing
cleaning
Bronco
Wet/Dry Vacuums
Stallion 8SC
*
Maneuverable, compact
automatic
Three high-performers
• 12-gal/45-l solution and recovery tanks
• 16-inch/41-cm cleaning path
• CX 300HP features
adjustable pressure—75 PSI
and 300 PSI, a 3-stage 2 HP
vacuum motor, and a heating
element for 212° F/100° C
solution
• 8-gal/30-l solution and recovery tanks
• 100 PSI solution pump cleans deep
• Powerful 3-stage vacuum motor with float shut-off
• Floating brush automatically adjusts to different carpet
pile heights
12-Gallon Predators
* Predator CX 300HP
• Predator 150 models deep
clean with a 150 PSI pump and dual 2-stage 1.25 HP vacuum motors
• CXH 150 includes a heating
element; CXC 150 uses cold
water
Page 16
Wet/Dry Vacuum Versatility
Built to fit into any budget, the Bronco series of vacuums offer both power
and economy.
Featuring 24, 8, and 4-gallon sizes, all Broncos have a powerful 1.34 HP
motor and ample airflow (102 CFM).
All three models include a professional wet/dry attachment tool kit.
The 24 gallon Bronco is available with a front mount squeegee which aids in
large-area wet pick-up.
Each Bronco vacuum includes a professional wet/dry attachment tool kit and
features a one-year warranty.
Page 5
AUTOMATIC SCRUBBERS
Sizable solution and recovery tanks mean less filling and
emptying, saving time and labor dollars. Powerful vacuum
motors and swing squeegees assure excellent water pick-up,
even on turns. Breakaway squeegee assemblies—straight
and curved are available—install quickly and minimize
the potential for damage. And for added convenience,
standard on-board battery chargers simplify recharging.
Champ ride-on scrubbers are designed for safe operation.
The open operator compartment provides maximum forward
visibility. A single, non-slip drive wheel turns 90 degrees in
both directions, providing incredible maneuverability.
Wrangler® autoscrubbers set the standard for reliability
and durability. Ask a service technician and you will find
NSS equipment stays on the job longer and needs fewer
repairs.
200,000+ ft2
18,580+ m2
90,000-140,000 ft2
8,361-13,006 m2
70,000-90,000 ft2
6,503-8,361 m2
50,000-70,000 ft2
4,645-6,503 m2
40,000-50,000 ft2
3,716-4,645 m2
Champ 3329
Wrangler 3330 DB
Wrangler 2730 DB
Wrangler 2625 DB
20,000-40,000 ft2
1,858-3,716 m2
Wrangler 2016 DB/AB
15,000-20,000 ft2
1,394-1,858 m2
Wrangler 2008 AB
Up to 15,000 ft2
Up to 1,394 m2
Wrangler 1708 AB
Outlaw B/V
Supercharge your
vacuum process
Uniquely comfortable
• Triangular body design maintains suction as bag fills
• 2-stage, flow-through motor
• 0.5 HP, 2-stage, 24V motor
• Comfortable and lightweight
just 10 lbs/4.5 kg
• Quiet—only 65 dBA—for
use anytime
• Adjustable for right- or left-hand users
• Ergonomic harness for operator comfort
• 400 cycle model available for use in aircraft
• 3-stage bagless filtration system assures great IAQ
Champ 3529
NSS autoscrubbers are famous for their quality, performance,
and simplicity. Each is built for the rigors of heavy-duty
commercial and industrial use. Instead of trendy bells and
whistles, NSS designs in reliable mechanisms to simplify
operator training and reduce service repair requirements.
Pacer PB
• Unrivaled spot vacuuming
productivity—up to 30,000 sq ft per hour
Champ 2929
Automatic Scrubbers
Choose your NSS scrubber.
How big is your floor?
140,000-200,000 ft2
13,006-18,580 m2
CARPET VACUUMS
• 1-2 hours runtime per set of NiMH batteries
Champ 3529
Advantage NSS
Works fast, built to last
• 35-inch/89-cm scrub path with a 46-inch/117-cm
curved squeegee
The Pacer PB uses powerful Nickel Metal
Hydride (NiMH) batteries.
This is 21st Century
technology—the same
battery chemistry used
in the latest hybrid cars.
• 29-gal/110-L solution tank
and oversized 32-gal/121-L
recovery tank
• 1 HP drive motor with three forward speeds
The distinction is dramatic. NiMH
batteries have up to twice the charge
densities of lead acid batteries. That means
more power and greater productivity—1 to
2 hours runtime from each set of batteries.
Since a Pacer PB can cover up to 30,000 sq ft
per hour, the payback is undeniable!
• 2.5 HP brush motor, adjustable 220-300 RPM brush speed
• Six 6V, 325 AH batteries
• Pictured with optional light
and bumper kits.
How fast do you want to clean?
15,000 ft2
Choose your NSS vacuum.
1,394 m2
Champ 3329
Champ 2929
Just the right size
Highly maneuverable
• 33-inch/84-cm scrub path with a 33-inch/84-cm curved squeegee
• 29-inch/74-cm scrub path with a 33-inch/84-cm curved squeegee
• 29-gal/110-L solution tank
and oversized 32-gal/121-L recovery tank
• 29-gal/110-L solution tank
and oversized 32-gal/121-L recovery tank
• 1 HP drive motor with two
forward speeds
• 1 HP drive motor with two
forward speeds
• 2 HP brush motor, 300 RPM brush speed
• 2 HP brush motor, 300 RPM brush speed
• Six 6V, 325 AH batteries
• Six 6V, 225 AH or 325 AH batteries
10,000 ft2
Pacer 30
929 m2
20,000 ft2
1,858 m2
Model M-1 “Pig”
with 16-in carpet tool
5,000 ft2
465 m2
0 ft2
25,000 ft2
Pacer 214/218 UE
Pacer 112/115 UE
Pacer PB (Spot Vacuuming)
2,323 m2
30,000 ft2
2,787 m2
0m
2
*Based on one hour of cleaning time.
Page 6
Page 15
CARPET VACUUMS
AUTOMATIC SCRUBBERS
Model M-1 “Pig”
Legendary durability—
only from NSS
• 1.5 HP bypass-cooled motor provides incredible suction
• Extra large 12-gal/53-l
debris filter bag
• “Scrap trap” collects nails and other large debris
• Cleans up to 25 ft overhead
without the risks of ladders
Hose and tools
sold separately
Carpet Vacuums
NSS carpet vacuums have earned a reputation for great
performance, reliability, and long life. The legendary Model
M-1 “Pig”®—the most productive, most durable and most
versatile vacuum available—remains a classic after decades
on the market. It has the power to thoroughly and safely
clean areas up to 25 feet in the air. That means your staff
keeps their feet on the ground and off of ladders, a true
safety benefit.
The Pacer 30 is the commercial industry standard in widearea vacuums, period. The Pacer two-motor uprights are
easy to use and provide superior cleaning power. The
lightweight, ergonomic Pacer 112/115 UE models have set
a new quality standard in single-motor uprights, a product
category dominated by mediocre, unreliable machines.
For superior productivity when spot vacuuming, choose
the cordless Pacer PB, the only PacVac designed from the
beginning to be battery-powered. With NiMH batteries
and a patented instant trigger, the Pacer PB will run up to
2 hours on a charge, covering up to 30,000 square feet per
hour. Sound incredible? It is. Thanks to its quiet operation,
the Pacer PB is ideal for use in healthcare facilities, 24/7
operations, and for cleaning occupied areas, day or night.
• Ideal for continuous-duty cleaning applications
including construction
clean-up
• 7-year limited warranty
• 25-inch/64-cm scrub path,
straight or curved squeegee
• 33-inch/84-cm or 27-inch/
69-cm scrub path; straight or
curved squeegee
• 25-gal/95-L solution tank;
27-gal/102-L recovery tank
• 30-gal/114-L solution tank
and 33-gal/125-L recovery
tank
• Two 0.75 HP brush motors and
a 0.75 HP vacuum motor
• Two 0.75 HP brush motors
and a 0.75 HP vacuum motor
• Variable speed propulsion and three scrub pressures
• Six 6V batteries—choose 225 AH or 325 AH
• Compact body designed for maneuverability
• Four 6-V, 225 AH batteries
• Variable speed drive system and three scrub pressures
Wrangler 2016 DB/
AB/AE
Wrangler 2008 AB/
AE & 1708 AB/AE
Maneuverable, mid-size
value
The best values in
compact scrubbers
• Quiet—only 69 dBA
• 20-inch/51-cm scrub path;
straight or curved squeegee
• Maneuverable for easy operation
• 16-gal/61-L solution and
17-gal/64-L recovery tank
• 20-inch/51-cm or 17-inch/43
cm scrub path; 32-inch
straight squeegee
• Simple adjustment for different carpet pile heights
• 0.75 HP brush motor and a
0.75 HP vacuum motor
(DB/AB)
Pacer 30
The wide-area standard
• 30-inch/76-cm work path
• Powerful dual 1-HP vacuum motors for cleaning muscle
• HEPA filter assembly available
• 8-gal/30-L solution and
10-gal/38-L recovery tank
• 0.75 HP brush motor and a 0.5
HP vacuum motor
• Ergonomic handles, two 8-inch rear wheels, and swivel front casters for maneuverability
• Offset scrub head for
superior edge cleaning
• Battery-powered wheel drive (DB) or pad drive (AB), and cord-electric pad drive (AE)
models available
Pacer 112/115 UE
ADD: Sidekick
Powerful, easy operation
Reliable—Really
• Dual motors—one each for suction and brush—for
maximum vacuum
performance
• Powerful 1.5 HP motor and chevron-style brush for thorough cleaning
Detergent dispensing
system
• On-board attachments and built-in wand for detail
cleaning
Mid-size with large
scrubber features
Rugged and
maneuverable
Pacer 214/218 UE
• Automatic shut-off protects brush motor if jammed
Wrangler 2625 DB
Wrangler
3330DB/2730 DB
• Lightweight, ergonomic design for operator comfort
• Easy, dust-free bag changes
• Reliable mechanical clutch disconnects brush if jammed
• 3-stage filtration for great IAQ
• Detachable suction tube makes clearing clogs simple
• Available in 14-inch/36-cm and 18-inch/46-cm widths
• Available in 12-inch/30-cm
and 15-inch/38-cm widths
• HEPA filter standard
• Add a variable-speed feed
pump and on-board
metering to any Wrangler
26, 27, 33, or Champ. Field
installation kit available
• Save money and time while
reducing employee
exposure
• Adds chemical to water en
route to the floor, keeping
the solution tank clean
• Battery-powered (AB) and
cord-electric (AE) models
available
Advantage NSS
Damp stripping or deep scrubbing VCT and
Terrazzo floors has never been easier than
with the Do No Harm™ Ecostrip pad
from NSS Enterprises. Remove yellow
top coats with just water, leaving a
surface that is ready for additional
finish or burnishing. Ecostrip pads
use an abrasive coating not
found in other stripping pads
to turn the top coat of finish into
a slurry which is easily collected by
an automatic scrubber. Ecostrip pads
can be used with most Wrangler and Champ
scrubbers and any NSS floor machine.
• Designed to work with any
brand of chemical
Coming soon - Fall 2009
Page 14
Page 7
WET/DRY VACUUMS
BATTERY BURNISHERS
Charger 2717 DB/AB
Colt 800 P
Bronco 24
Enhanced productivity
and durability
Compact, affordable
performer
Strong suction, big value
• Consistently produces a high gloss shine without the need for operator adjustment
• Powerful 1.23 HP bypass-cooled vacuum motor
• 27-inch/69-cm work path
• 3.6 HP pad drive motor
delivers 1700 RPM pad speed
• Six 6V, 325 AH batteries for up
to 3 hours per charge
• Hinged 90° head mechanism for compact storage and standing pad changes
• 1.34 HP, 2-stage bypass-type
motor provides strong suction
• 24-gal/90-L wet recovery capacity
• Quiet operation—just 62 dBA
• 8-gal/30-L rotocast polyethylene tank for long life
• Non-corrosive, dent-proof,
blow-molded polyethylene
tank
• Drain plug for easy emptying
• Front-mount squeegee optional
• Includes 7-piece wet/dry
tool kit
• Customize with tool kit sold
separately
• Optional front mount
squeegee for quick liquid
recovery.
Battery Burnishers
• Quiet operation—only 68 dBA
—means minimal disruption
NSS battery burnishers were designed to help customers
achieve a high-gloss shine while escaping the hassles of
propane machines. The concerns with propane—frequent
repairs, high maintenance costs, disruptive noise levels,
indoor carbon monoxide emissions, exposed hot engine
parts, and other safety issues—were only tolerated since
there were no better options. Now that has changed.
Charger 2022 DB
Bronco 8
Bronco 4
Compact and
maneuverable
Solid, economical performer
Economical and versatile
• 1.34 HP, 2-stage bypass-type motor provides strong suction
• 1.34 HP, 2-stage bypass-type motor provides strong suction
• 8-gal/30-L wet recovery capacity
• 4-gal/15-L wet recovery capacity
• 20-inch/51-cm burnishing path
Charger battery burnishers have the power and pad
pressure to produce a high-gloss shine. Even better, quiet
operation allows scheduling flexibility to burnish in occupied
facilities anytime, with minimal disruption to customers and
co-workers. To maintain indoor air quality, every Charger
includes a Vac-Trac system to collects floor finish powder
and pad dust.
• 2.5 HP pad drive motor delivers a 2200 RPM pad speed
Chargers are built for ease of operation and long life. Heavyduty steel structures provide a solid, durable foundation.
Standard on-board battery chargers assure convenient and
consistent recharging anywhere there is a plug available.
And using the correct charger helps to maximize battery life.
Each machine is designed for easy pad changes—just one
example of the many operator-friendly features designed
into every NSS Charger battery burnisher.
• Variable speed wheel-drive (DB)
propulsion
• Hinged 90° head mechanism for compact storage and standing pad changes
ADD: Sulky
Charger 2022 ABLT
Boost productivity and
performance
Compact, economical
maneuverability
• The sulky attachment allows
the operator to ride behind
the burnisher, reducing
operator fatigue
• 20-inch/51-cm burnishing path
• Increase productivity without
the expense and maintenance
of a ride-on burnisher
• Sulky latches to the back of the
machine for maneuverability in
tight places
• For wheel-drive units 2717 DB and 2022 DB
Page 8
• Six 6V, 225 AH batteries for up
to 3 hours runtime
• 2.5 HP pad drive motor delivers a 2200 RPM pad speed
• Four 6V, 225 AH batteries for
up to 3 hours runtime
• Hinged 90° head mechanism for compact storage and standing pad changes
• Pad-assist (AB) propulsion
• Non-corrosive, dent-proof,
polyethylene tank
• Polyethylene tank for long life
• Includes a standard 7-piece
wet/dry tool kit
• Lightweight—only 19 lbs.
• 2-caster, 2-wheel base for
maneuverability
• Includes 8-piece wet/dry tool kit
Advantage NSS
NSS has engineered a unique
system to muffle vacuum noise,
leveraging the benefits of
roto-molding. To quiet the
motor on the BP Rangers
and Colts, suction air
(black arrows) is squeezed
through narrow openings
and released into larger
chambers within the
powerhead—much like a car’s
exhaust system.
A separate stream of clean, fresh air (red
arrows) cools the motor, protecting it from
moisture and debris.
Page 13
CORD-ELECTRIC BURNISHERS
WET/DRY VACUUMS
BP Ranger
Charger 2500
Unmatched performance
and durability
The Ultra High-Speed
“Finisher”
• Powerful 2 HP bypasscooled vacuum motor
• Produces a brilliant, high-gloss shine
• 50% more waterlift and 5 to 10 times longer life than
typical wet/drys
• 20-inch/51-cm workpath
• 2500 RPM pad speed
• 1.5 HP motor for long life and exceptional results
• Patented noise reduction system assures quiet
operation—65 dBA
• 12.5-gal/48-L stainless steel or 14.5 gal/55-L rotocast polyethylene tip-dispose
tank
Wet/Dry Vacuums
NSS offers three lines of wet/drys to provide options for any
need and budget. Choose from the extreme performance
BP Rangers, the affordable Colts, or the economical
Broncos. All are versatile machines, handy for jobs ranging
from dry spill pickup to stripping solution recovery.
Standard on all BP Ranger and Colt models, NSS’s
patented noise reduction system means quiet operation
without diminishing vacuum performance. All BP Rangers
and most Colt models have a tip-dispose base. Optional
front mount squeegees, available on all BP Rangers and
Colts, dramatically boost productivity. For enhanced IAQ,
a HEPA filter is available on most Colt models.
• Customize with tool kit sold
separately
• 7-year limited warranty
Cord-Electric Burnishers
NSS cord-electric burnishers produce a high-gloss shine
and are built to last for years to come.
Colt 1250 S/1450 P
Affordable high
performers
• Powerful 1.23 HP bypass cooled vacuum motor
• Patented noise reduction system assures quiet
operation—only 62 dBA
• 12.5-gal/48-L stainless steel or 14.5 gal/55-L rotocast polyethylene tank
• Tip-dispose tank for easy emptying
• Customize with tool kit sold
separately
All NSS cord-electric burnishers have a powerful 1.5 HP
motor and a built-in pad driver for smooth, balanced, and
safe operation. Each is designed for quiet performance,
operator comfort, and simple usage. The Flexiwall shield
controls dust and prevents the cord and debris from
contacting the rotating pad. And the standard safety lockout
mechanism helps prevent accidental or unauthorized use.
The brilliant finish from the ultra high-speed Charger 2500 is
comparable to that produced by big battery machines. The
Charger 1500—a hallmark of the NSS line—is unmatched
for its durability and versatility. The 7-year warranty on these
Chargers speaks for itself. The Mustang 1500, Mustang 1500
Vac-Trac, and Galaxy 1500 are outstanding performers, and
outstanding values too.
Charger 1500
Versatile, and built to be
the best
• Use to burnish, spray buff, or
damp scrub
• 20-inch/51-cm workpath
• 1500 RPM pad speed for a
wet-look shine
• 1.5 HP motor and a unique
pad driver with inertial steel
plate tackle any job with ease
• 7-year limited warranty
ADD: Front mount
squeegee
ADD: HEPA Filtration
Galaxy 1500
Mustang 1500
Further enhance IAQ
• Removes particles as small as 0.3 microns at 99.997 percent efficiency for
maximum Indoor Air Quality
Economical high gloss
shine
Dependable and affordable
Boost productivity and
performance
• Produces high-gloss shine
• 20-inch/51-cm workpath
• 20-inch/51-cm workpath
• 1.5 HP motor and 1500 RPM pad
speed for prodcutivity
• Recovers liquid up to four
times faster than using a hose
and squeegee tool
• Ideal when stripping large
areas or drying flooded floors
• Toe-operated squeegee leaves a clear path
• Available on BP Ranger and
Colt models as well as the
Bronco 24
Page 12
• Adjustable pad pressure for
optimal burnishing
• Ideal for healthcare,
restaurants, and hospitality applications
• Available on Colt 800 PB,
1250 S, and 1450 P models
• 1.5 HP motor and 1500 RPM pad speed for productivity
• Built-in wheel carriage for easy transport on stairways
• Packaged to ship via small
parcel service
• Produces a high-gloss shine
• Available with Vac-Trac filter for
great IAQ
• Built-in wheel carriage for easy transport on stairways
• Safety-yellow bumper protects
furniture and fixtures
Page 9
FLOOR MACHINES
SWEEPERS
Maverick 300
Manta RS 36
Ultimate versatility
Ride-on efficiency
• Variable speed—from 200 to 310 RPM—for multiple uses
• Sweep large areas quickly, indoors or outdoors
• Powerful 1.5 HP, 66-frame motor
• 37.4-inch/95-cm total workpath
• Durable triple-idler planetary
gearbox
• Heavy-duty 0.5 HP drive motor for speeds up to 3.5 MPH
• Structural foam pad driver
• Two 12V, 145 AH batteries provide up to 2.5 hours runtime
• Huge 3 cu ft/85-l hopper
• 17-inch/34-cm or 20-inch/ 51-cm work path
• On-board battery charger simplifies recharging
Floor Machines
Sweepers
NSS floor machines are famed for quality, reliability, and easy
operation. Is there a difference? Absolutely. Heavy-duty
yellow safety cords are just one example of the engineering
and quality built into every NSS floor machine.
NSS sweepers keep your facility looking its best—inside
and out. Built for long life, each model is easy to use
and maneuverable. Three sweepers are available to clean
any application or floor surface, including hard floors and
carpet.
A variety of machines are available to meet your job
specifications and price point. Optional solution tanks
are available for speed scrubbing and bonnet cleaning.
And a safety lockout mechanism restricts unauthorized or
unintended operation.
Perform a wide variety of floor care operations—for both
hard floors and carpet—with NSS floor machines. Use to
polish, spray buff, scrub, or wet strip hard floors. Add a
bonnet to clean carpet between extractions. Whatever your
budget or application, NSS offers a durable floor machine
to meet your needs.
Thoroughbred
Built to be the best
• Incredibly durable, dependable, and powerful
• Rugged, polished cast aluminum motor mount and skirt
• 12V, 145 AH battery provides hours of continuous operation
• 11:1 planetary gear drive
• Structural foam pad driver
• On-board battery charger recharges anywhere a plug is available
• 17-inch/34-cm or 20-inch/ 51-cm work path
Dependable and
affordable
Durable and economical
Versatile and economical
• Durable, chrome-plated
base and handle for
extended life
• Increases productivity—up to 5 times faster than a push broom
• Ergonomic handle adjustment and cord release
• 27-inch/69-cm workpath
• 1 or 1.5 HP, 66-frame motor
• 300 DS model operates at 300
RPM to polish/spray buff or at
180 RPM to scrub/wet strip
• 300 DS model operates at
300 RPM to polish/spray
buff or at 180 RPM to scrub
wet strip
• 17-inch/34-cm or 20-inch/
51-cm work path
• 17-inch/34-cm or 20-inch/ 51-cm work path
• Packaged to ship via small
parcel service
Page 10
• 27.5-inch/70-cm total workpath
• Large, 11.3 gal dry /43-l hopper
Sidewinder 27
• Straight line planetary gear
system efficiently transfers
power
• Battery-powered brushes provide
for a highly maneuverable
sweeper
• Heavy-duty 1 or 1.5 HP motor
Galaxy Series
• 1 or 1.5 HP, 66-frame motor
Battery-powered
performance
Choose the Manta RS 36 ride-on to sweep large areas
quickly. The Sidewinder 27 MB is compact battery-powered
walk-behind sweeper, ideal for large areas. Replace your
push broom with the Sidewinder 27 and sweep five times
faster.
Mustang Series
• Precision-balanced for smooth
operation and maneuverability
Sidewinder 27 MB
• 1.4 cu ft/40-l easily removable hopper
• Durable and lightweight
• Use indoors or outdoors on carpet or hard surfaces, even in damp conditions
Advantage NSS
NSS has always been driven by the belief that
the act of cleaning should “do no harm” to
our customer-operators or the environment.
The features of our
“human engineered”
products protect the
health and safety of
the operator. Durability,
longevity, and flexibility
are designed into every piece of NSS
equipment. Because our products are built
to last, you’ll find NSS equipment hard at
work for years—and even decades—after
competitors’ products have failed and made
the trip to a landfill.
Page 11
FLOOR MACHINES
SWEEPERS
Maverick 300
Manta RS 36
Ultimate versatility
Ride-on efficiency
• Variable speed—from 200 to 310 RPM—for multiple uses
• Sweep large areas quickly, indoors or outdoors
• Powerful 1.5 HP, 66-frame motor
• 37.4-inch/95-cm total workpath
• Durable triple-idler planetary
gearbox
• Heavy-duty 0.5 HP drive motor for speeds up to 3.5 MPH
• Structural foam pad driver
• Two 12V, 145 AH batteries provide up to 2.5 hours runtime
• Huge 3 cu ft/85-l hopper
• 17-inch/34-cm or 20-inch/ 51-cm work path
• On-board battery charger simplifies recharging
Floor Machines
Sweepers
NSS floor machines are famed for quality, reliability, and easy
operation. Is there a difference? Absolutely. Heavy-duty
yellow safety cords are just one example of the engineering
and quality built into every NSS floor machine.
NSS sweepers keep your facility looking its best—inside
and out. Built for long life, each model is easy to use
and maneuverable. Three sweepers are available to clean
any application or floor surface, including hard floors and
carpet.
A variety of machines are available to meet your job
specifications and price point. Optional solution tanks
are available for speed scrubbing and bonnet cleaning.
And a safety lockout mechanism restricts unauthorized or
unintended operation.
Perform a wide variety of floor care operations—for both
hard floors and carpet—with NSS floor machines. Use to
polish, spray buff, scrub, or wet strip hard floors. Add a
bonnet to clean carpet between extractions. Whatever your
budget or application, NSS offers a durable floor machine
to meet your needs.
Thoroughbred
Built to be the best
• Incredibly durable, dependable, and powerful
• Rugged, polished cast aluminum motor mount and skirt
• 12V, 145 AH battery provides hours of continuous operation
• 11:1 planetary gear drive
• Structural foam pad driver
• On-board battery charger recharges anywhere a plug is available
• 17-inch/34-cm or 20-inch/ 51-cm work path
Dependable and
affordable
Durable and economical
Versatile and economical
• Durable, chrome-plated
base and handle for
extended life
• Increases productivity—up to 5 times faster than a push broom
• Ergonomic handle adjustment and cord release
• 27-inch/69-cm workpath
• 1 or 1.5 HP, 66-frame motor
• 300 DS model operates at 300
RPM to polish/spray buff or at
180 RPM to scrub/wet strip
• 300 DS model operates at
300 RPM to polish/spray
buff or at 180 RPM to scrub
wet strip
• 17-inch/34-cm or 20-inch/
51-cm work path
• 17-inch/34-cm or 20-inch/ 51-cm work path
• Packaged to ship via small
parcel service
Page 10
• 27.5-inch/70-cm total workpath
• Large, 11.3 gal dry /43-l hopper
Sidewinder 27
• Straight line planetary gear
system efficiently transfers
power
• Battery-powered brushes provide
for a highly maneuverable
sweeper
• Heavy-duty 1 or 1.5 HP motor
Galaxy Series
• 1 or 1.5 HP, 66-frame motor
Battery-powered
performance
Choose the Manta RS 36 ride-on to sweep large areas
quickly. The Sidewinder 27 MB is compact battery-powered
walk-behind sweeper, ideal for large areas. Replace your
push broom with the Sidewinder 27 and sweep five times
faster.
Mustang Series
• Precision-balanced for smooth
operation and maneuverability
Sidewinder 27 MB
• 1.4 cu ft/40-l easily removable hopper
• Durable and lightweight
• Use indoors or outdoors on carpet or hard surfaces, even in damp conditions
Advantage NSS
NSS has always been driven by the belief that
the act of cleaning should “do no harm” to
our customer-operators or the environment.
The features of our
“human engineered”
products protect the
health and safety of
the operator. Durability,
longevity, and flexibility
are designed into every piece of NSS
equipment. Because our products are built
to last, you’ll find NSS equipment hard at
work for years—and even decades—after
competitors’ products have failed and made
the trip to a landfill.
Page 11
CORD-ELECTRIC BURNISHERS
WET/DRY VACUUMS
BP Ranger
Charger 2500
Unmatched performance
and durability
The Ultra High-Speed
“Finisher”
• Powerful 2 HP bypasscooled vacuum motor
• Produces a brilliant, high-gloss shine
• 50% more waterlift and 5 to 10 times longer life than
typical wet/drys
• 20-inch/51-cm workpath
• 2500 RPM pad speed
• 1.5 HP motor for long life and exceptional results
• Patented noise reduction system assures quiet
operation—65 dBA
• 12.5-gal/48-L stainless steel or 14.5 gal/55-L rotocast polyethylene tip-dispose
tank
Wet/Dry Vacuums
NSS offers three lines of wet/drys to provide options for any
need and budget. Choose from the extreme performance
BP Rangers, the affordable Colts, or the economical
Broncos. All are versatile machines, handy for jobs ranging
from dry spill pickup to stripping solution recovery.
Standard on all BP Ranger and Colt models, NSS’s
patented noise reduction system means quiet operation
without diminishing vacuum performance. All BP Rangers
and most Colt models have a tip-dispose base. Optional
front mount squeegees, available on all BP Rangers and
Colts, dramatically boost productivity. For enhanced IAQ,
a HEPA filter is available on most Colt models.
• Customize with tool kit sold
separately
• 7-year limited warranty
Cord-Electric Burnishers
NSS cord-electric burnishers produce a high-gloss shine
and are built to last for years to come.
Colt 1250 S/1450 P
Affordable high
performers
• Powerful 1.23 HP bypass cooled vacuum motor
• Patented noise reduction system assures quiet
operation—only 62 dBA
• 12.5-gal/48-L stainless steel or 14.5 gal/55-L rotocast polyethylene tank
• Tip-dispose tank for easy emptying
• Customize with tool kit sold
separately
All NSS cord-electric burnishers have a powerful 1.5 HP
motor and a built-in pad driver for smooth, balanced, and
safe operation. Each is designed for quiet performance,
operator comfort, and simple usage. The Flexiwall shield
controls dust and prevents the cord and debris from
contacting the rotating pad. And the standard safety lockout
mechanism helps prevent accidental or unauthorized use.
The brilliant finish from the ultra high-speed Charger 2500 is
comparable to that produced by big battery machines. The
Charger 1500—a hallmark of the NSS line—is unmatched
for its durability and versatility. The 7-year warranty on these
Chargers speaks for itself. The Mustang 1500, Mustang 1500
Vac-Trac, and Galaxy 1500 are outstanding performers, and
outstanding values too.
Charger 1500
Versatile, and built to be
the best
• Use to burnish, spray buff, or
damp scrub
• 20-inch/51-cm workpath
• 1500 RPM pad speed for a
wet-look shine
• 1.5 HP motor and a unique
pad driver with inertial steel
plate tackle any job with ease
• 7-year limited warranty
ADD: Front mount
squeegee
ADD: HEPA Filtration
Galaxy 1500
Mustang 1500
Further enhance IAQ
• Removes particles as small as 0.3 microns at 99.997 percent efficiency for
maximum Indoor Air Quality
Economical high gloss
shine
Dependable and affordable
Boost productivity and
performance
• Produces high-gloss shine
• 20-inch/51-cm workpath
• 20-inch/51-cm workpath
• 1.5 HP motor and 1500 RPM pad
speed for prodcutivity
• Recovers liquid up to four
times faster than using a hose
and squeegee tool
• Ideal when stripping large
areas or drying flooded floors
• Toe-operated squeegee leaves a clear path
• Available on BP Ranger and
Colt models as well as the
Bronco 24
Page 12
• Adjustable pad pressure for
optimal burnishing
• Ideal for healthcare,
restaurants, and hospitality applications
• Available on Colt 800 PB,
1250 S, and 1450 P models
• 1.5 HP motor and 1500 RPM pad speed for productivity
• Built-in wheel carriage for easy transport on stairways
• Packaged to ship via small
parcel service
• Produces a high-gloss shine
• Available with Vac-Trac filter for
great IAQ
• Built-in wheel carriage for easy transport on stairways
• Safety-yellow bumper protects
furniture and fixtures
Page 9
WET/DRY VACUUMS
BATTERY BURNISHERS
Charger 2717 DB/AB
Colt 800 P
Bronco 24
Enhanced productivity
and durability
Compact, affordable
performer
Strong suction, big value
• Consistently produces a high gloss shine without the need for operator adjustment
• Powerful 1.23 HP bypass-cooled vacuum motor
• 27-inch/69-cm work path
• 3.6 HP pad drive motor
delivers 1700 RPM pad speed
• Six 6V, 325 AH batteries for up
to 3 hours per charge
• Hinged 90° head mechanism for compact storage and standing pad changes
• 1.34 HP, 2-stage bypass-type
motor provides strong suction
• 24-gal/90-L wet recovery capacity
• Quiet operation—just 62 dBA
• 8-gal/30-L rotocast polyethylene tank for long life
• Non-corrosive, dent-proof,
blow-molded polyethylene
tank
• Drain plug for easy emptying
• Front-mount squeegee optional
• Includes 7-piece wet/dry
tool kit
• Customize with tool kit sold
separately
• Optional front mount
squeegee for quick liquid
recovery.
Battery Burnishers
• Quiet operation—only 68 dBA
—means minimal disruption
NSS battery burnishers were designed to help customers
achieve a high-gloss shine while escaping the hassles of
propane machines. The concerns with propane—frequent
repairs, high maintenance costs, disruptive noise levels,
indoor carbon monoxide emissions, exposed hot engine
parts, and other safety issues—were only tolerated since
there were no better options. Now that has changed.
Charger 2022 DB
Bronco 8
Bronco 4
Compact and
maneuverable
Solid, economical performer
Economical and versatile
• 1.34 HP, 2-stage bypass-type motor provides strong suction
• 1.34 HP, 2-stage bypass-type motor provides strong suction
• 8-gal/30-L wet recovery capacity
• 4-gal/15-L wet recovery capacity
• 20-inch/51-cm burnishing path
Charger battery burnishers have the power and pad
pressure to produce a high-gloss shine. Even better, quiet
operation allows scheduling flexibility to burnish in occupied
facilities anytime, with minimal disruption to customers and
co-workers. To maintain indoor air quality, every Charger
includes a Vac-Trac system to collects floor finish powder
and pad dust.
• 2.5 HP pad drive motor delivers a 2200 RPM pad speed
Chargers are built for ease of operation and long life. Heavyduty steel structures provide a solid, durable foundation.
Standard on-board battery chargers assure convenient and
consistent recharging anywhere there is a plug available.
And using the correct charger helps to maximize battery life.
Each machine is designed for easy pad changes—just one
example of the many operator-friendly features designed
into every NSS Charger battery burnisher.
• Variable speed wheel-drive (DB)
propulsion
• Hinged 90° head mechanism for compact storage and standing pad changes
ADD: Sulky
Charger 2022 ABLT
Boost productivity and
performance
Compact, economical
maneuverability
• The sulky attachment allows
the operator to ride behind
the burnisher, reducing
operator fatigue
• 20-inch/51-cm burnishing path
• Increase productivity without
the expense and maintenance
of a ride-on burnisher
• Sulky latches to the back of the
machine for maneuverability in
tight places
• For wheel-drive units 2717 DB and 2022 DB
Page 8
• Six 6V, 225 AH batteries for up
to 3 hours runtime
• 2.5 HP pad drive motor delivers a 2200 RPM pad speed
• Four 6V, 225 AH batteries for
up to 3 hours runtime
• Hinged 90° head mechanism for compact storage and standing pad changes
• Pad-assist (AB) propulsion
• Non-corrosive, dent-proof,
polyethylene tank
• Polyethylene tank for long life
• Includes a standard 7-piece
wet/dry tool kit
• Lightweight—only 19 lbs.
• 2-caster, 2-wheel base for
maneuverability
• Includes 8-piece wet/dry tool kit
Advantage NSS
NSS has engineered a unique
system to muffle vacuum noise,
leveraging the benefits of
roto-molding. To quiet the
motor on the BP Rangers
and Colts, suction air
(black arrows) is squeezed
through narrow openings
and released into larger
chambers within the
powerhead—much like a car’s
exhaust system.
A separate stream of clean, fresh air (red
arrows) cools the motor, protecting it from
moisture and debris.
Page 13
CARPET VACUUMS
AUTOMATIC SCRUBBERS
Model M-1 “Pig”
Legendary durability—
only from NSS
• 1.5 HP bypass-cooled motor provides incredible suction
• Extra large 12-gal/53-l
debris filter bag
• “Scrap trap” collects nails and other large debris
• Cleans up to 25 ft overhead
without the risks of ladders
Hose and tools
sold separately
Carpet Vacuums
NSS carpet vacuums have earned a reputation for great
performance, reliability, and long life. The legendary Model
M-1 “Pig”®—the most productive, most durable and most
versatile vacuum available—remains a classic after decades
on the market. It has the power to thoroughly and safely
clean areas up to 25 feet in the air. That means your staff
keeps their feet on the ground and off of ladders, a true
safety benefit.
The Pacer 30 is the commercial industry standard in widearea vacuums, period. The Pacer two-motor uprights are
easy to use and provide superior cleaning power. The
lightweight, ergonomic Pacer 112/115 UE models have set
a new quality standard in single-motor uprights, a product
category dominated by mediocre, unreliable machines.
For superior productivity when spot vacuuming, choose
the cordless Pacer PB, the only PacVac designed from the
beginning to be battery-powered. With NiMH batteries
and a patented instant trigger, the Pacer PB will run up to
2 hours on a charge, covering up to 30,000 square feet per
hour. Sound incredible? It is. Thanks to its quiet operation,
the Pacer PB is ideal for use in healthcare facilities, 24/7
operations, and for cleaning occupied areas, day or night.
• Ideal for continuous-duty cleaning applications
including construction
clean-up
• 7-year limited warranty
• 25-inch/64-cm scrub path,
straight or curved squeegee
• 33-inch/84-cm or 27-inch/
69-cm scrub path; straight or
curved squeegee
• 25-gal/95-L solution tank;
27-gal/102-L recovery tank
• 30-gal/114-L solution tank
and 33-gal/125-L recovery
tank
• Two 0.75 HP brush motors and
a 0.75 HP vacuum motor
• Two 0.75 HP brush motors
and a 0.75 HP vacuum motor
• Variable speed propulsion and three scrub pressures
• Six 6V batteries—choose 225 AH or 325 AH
• Compact body designed for maneuverability
• Four 6-V, 225 AH batteries
• Variable speed drive system and three scrub pressures
Wrangler 2016 DB/
AB/AE
Wrangler 2008 AB/
AE & 1708 AB/AE
Maneuverable, mid-size
value
The best values in
compact scrubbers
• Quiet—only 69 dBA
• 20-inch/51-cm scrub path;
straight or curved squeegee
• Maneuverable for easy operation
• 16-gal/61-L solution and
17-gal/64-L recovery tank
• 20-inch/51-cm or 17-inch/43
cm scrub path; 32-inch
straight squeegee
• Simple adjustment for different carpet pile heights
• 0.75 HP brush motor and a
0.75 HP vacuum motor
(DB/AB)
Pacer 30
The wide-area standard
• 30-inch/76-cm work path
• Powerful dual 1-HP vacuum motors for cleaning muscle
• HEPA filter assembly available
• 8-gal/30-L solution and
10-gal/38-L recovery tank
• 0.75 HP brush motor and a 0.5
HP vacuum motor
• Ergonomic handles, two 8-inch rear wheels, and swivel front casters for maneuverability
• Offset scrub head for
superior edge cleaning
• Battery-powered wheel drive (DB) or pad drive (AB), and cord-electric pad drive (AE)
models available
Pacer 112/115 UE
ADD: Sidekick
Powerful, easy operation
Reliable—Really
• Dual motors—one each for suction and brush—for
maximum vacuum
performance
• Powerful 1.5 HP motor and chevron-style brush for thorough cleaning
Detergent dispensing
system
• On-board attachments and built-in wand for detail
cleaning
Mid-size with large
scrubber features
Rugged and
maneuverable
Pacer 214/218 UE
• Automatic shut-off protects brush motor if jammed
Wrangler 2625 DB
Wrangler
3330DB/2730 DB
• Lightweight, ergonomic design for operator comfort
• Easy, dust-free bag changes
• Reliable mechanical clutch disconnects brush if jammed
• 3-stage filtration for great IAQ
• Detachable suction tube makes clearing clogs simple
• Available in 14-inch/36-cm and 18-inch/46-cm widths
• Available in 12-inch/30-cm
and 15-inch/38-cm widths
• HEPA filter standard
• Add a variable-speed feed
pump and on-board
metering to any Wrangler
26, 27, 33, or Champ. Field
installation kit available
• Save money and time while
reducing employee
exposure
• Adds chemical to water en
route to the floor, keeping
the solution tank clean
• Battery-powered (AB) and
cord-electric (AE) models
available
Advantage NSS
Damp stripping or deep scrubbing VCT and
Terrazzo floors has never been easier than
with the Do No Harm™ Ecostrip pad
from NSS Enterprises. Remove yellow
top coats with just water, leaving a
surface that is ready for additional
finish or burnishing. Ecostrip pads
use an abrasive coating not
found in other stripping pads
to turn the top coat of finish into
a slurry which is easily collected by
an automatic scrubber. Ecostrip pads
can be used with most Wrangler and Champ
scrubbers and any NSS floor machine.
• Designed to work with any
brand of chemical
Coming soon - Fall 2009
Page 14
Page 7
AUTOMATIC SCRUBBERS
Sizable solution and recovery tanks mean less filling and
emptying, saving time and labor dollars. Powerful vacuum
motors and swing squeegees assure excellent water pick-up,
even on turns. Breakaway squeegee assemblies—straight
and curved are available—install quickly and minimize
the potential for damage. And for added convenience,
standard on-board battery chargers simplify recharging.
Champ ride-on scrubbers are designed for safe operation.
The open operator compartment provides maximum forward
visibility. A single, non-slip drive wheel turns 90 degrees in
both directions, providing incredible maneuverability.
Wrangler® autoscrubbers set the standard for reliability
and durability. Ask a service technician and you will find
NSS equipment stays on the job longer and needs fewer
repairs.
200,000+ ft2
18,580+ m2
90,000-140,000 ft2
8,361-13,006 m2
70,000-90,000 ft2
6,503-8,361 m2
50,000-70,000 ft2
4,645-6,503 m2
40,000-50,000 ft2
3,716-4,645 m2
Champ 3329
Wrangler 3330 DB
Wrangler 2730 DB
Wrangler 2625 DB
20,000-40,000 ft2
1,858-3,716 m2
Wrangler 2016 DB/AB
15,000-20,000 ft2
1,394-1,858 m2
Wrangler 2008 AB
Up to 15,000 ft2
Up to 1,394 m2
Wrangler 1708 AB
Outlaw B/V
Supercharge your
vacuum process
Uniquely comfortable
• Triangular body design maintains suction as bag fills
• 2-stage, flow-through motor
• 0.5 HP, 2-stage, 24V motor
• Comfortable and lightweight
just 10 lbs/4.5 kg
• Quiet—only 65 dBA—for
use anytime
• Adjustable for right- or left-hand users
• Ergonomic harness for operator comfort
• 400 cycle model available for use in aircraft
• 3-stage bagless filtration system assures great IAQ
Champ 3529
NSS autoscrubbers are famous for their quality, performance,
and simplicity. Each is built for the rigors of heavy-duty
commercial and industrial use. Instead of trendy bells and
whistles, NSS designs in reliable mechanisms to simplify
operator training and reduce service repair requirements.
Pacer PB
• Unrivaled spot vacuuming
productivity—up to 30,000 sq ft per hour
Champ 2929
Automatic Scrubbers
Choose your NSS scrubber.
How big is your floor?
140,000-200,000 ft2
13,006-18,580 m2
CARPET VACUUMS
• 1-2 hours runtime per set of NiMH batteries
Champ 3529
Advantage NSS
Works fast, built to last
• 35-inch/89-cm scrub path with a 46-inch/117-cm
curved squeegee
The Pacer PB uses powerful Nickel Metal
Hydride (NiMH) batteries.
This is 21st Century
technology—the same
battery chemistry used
in the latest hybrid cars.
• 29-gal/110-L solution tank
and oversized 32-gal/121-L
recovery tank
• 1 HP drive motor with three forward speeds
The distinction is dramatic. NiMH
batteries have up to twice the charge
densities of lead acid batteries. That means
more power and greater productivity—1 to
2 hours runtime from each set of batteries.
Since a Pacer PB can cover up to 30,000 sq ft
per hour, the payback is undeniable!
• 2.5 HP brush motor, adjustable 220-300 RPM brush speed
• Six 6V, 325 AH batteries
• Pictured with optional light
and bumper kits.
How fast do you want to clean?
15,000 ft2
Choose your NSS vacuum.
1,394 m2
Champ 3329
Champ 2929
Just the right size
Highly maneuverable
• 33-inch/84-cm scrub path with a 33-inch/84-cm curved squeegee
• 29-inch/74-cm scrub path with a 33-inch/84-cm curved squeegee
• 29-gal/110-L solution tank
and oversized 32-gal/121-L recovery tank
• 29-gal/110-L solution tank
and oversized 32-gal/121-L recovery tank
• 1 HP drive motor with two
forward speeds
• 1 HP drive motor with two
forward speeds
• 2 HP brush motor, 300 RPM brush speed
• 2 HP brush motor, 300 RPM brush speed
• Six 6V, 325 AH batteries
• Six 6V, 225 AH or 325 AH batteries
10,000 ft2
Pacer 30
929 m2
20,000 ft2
1,858 m2
Model M-1 “Pig”
with 16-in carpet tool
5,000 ft2
465 m2
0 ft2
25,000 ft2
Pacer 214/218 UE
Pacer 112/115 UE
Pacer PB (Spot Vacuuming)
2,323 m2
30,000 ft2
2,787 m2
0m
2
*Based on one hour of cleaning time.
Page 6
Page 15
CARPET EXTRACTORS
NEW PRODUCT
Pony 20 SCA
Powerful, large area
automatic
• 22-inch/56-cm cleaning path
• 20-gal/76-l solution and recovery tanks
• 100 PSI solution pump for deep cleaning
• Powerful 3-stage vacuum motor with float shut-off
• Variable speed propulsion
system
• Built-in spray wand
Carpet Extractors
NSS extractors keep your carpets looking their best. There
is a machine to meet every carpet cleaning need, each
constructed for maximum performance, durability, and
long life.
Stallion 12 SC
Galaxy 1500
Cord-Electric Burnisher
Economical High Gloss Shine
The Galaxy 1500 is a durable, economical cord-electric burnisher that
performs with the high-quality hard floor efficiency you’ve come to expect
from NSS.
The unique features of the Galaxy 1500 set it apart from other economical
burnishers. The chrome-plated handle prevents corrosion, and the chromeplated deck resists the effects of harsh floor finishes and chemicals. Built-in
transport wheels at the rear of the unit assist in transporting the Galaxy
1500 in and out of buildings and vehicles. And an ergonomic handle
adjustment allows the operator to set the handle height for comfort.
As with other Galaxy models, the Galaxy 1500 features our patented twopart packaging system, allowing shipment via small parcel service.
Excellent mid-size
extractor
The Pony 20 SCA, Stallion 12 SC, and Stallion 8SC selfcontained extractors are the choice for fast, effective
cleaning. These NSS automatics complete your job in half
the time of a tank extractor. Their tank-over-tank design
improves sight lines and keeps the machines balanced from
job start to finish. Both machines can be used with optional
upholstery and stair cleaning tools and a 3-jet wand.
• 18-inch/46-cm cleaning path
• 12-gal/45.5-l solution and
dual 6-gal recovery tanks
• 100 PSI solution pump cleans deep
• Powerful 3.5 HP, 2-stage
vacuum motor
The Predator CX 300 HP is NSS’s deluxe, dual pressure hot
water tank unit. Four additional models of Predator tank
extractors let you choose hot- or cold-water cleaning in two
different size units. The handy Predator CX3 features a third
tank for clean rinse water. For floor applications to ceiling
applications, the Aero plus dryer speeds drying time by as
much as 50 percent.
• Low-flow solution switch
uses less water, conserving
water without sacrificing
cleaning
Bronco
Wet/Dry Vacuums
Stallion 8SC
*
Maneuverable, compact
automatic
Three high-performers
• 12-gal/45-l solution and recovery tanks
• 16-inch/41-cm cleaning path
• CX 300HP features
adjustable pressure—75 PSI
and 300 PSI, a 3-stage 2 HP
vacuum motor, and a heating
element for 212° F/100° C
solution
• 8-gal/30-l solution and recovery tanks
• 100 PSI solution pump cleans deep
• Powerful 3-stage vacuum motor with float shut-off
• Floating brush automatically adjusts to different carpet
pile heights
12-Gallon Predators
* Predator CX 300HP
• Predator 150 models deep
clean with a 150 PSI pump and dual 2-stage 1.25 HP vacuum motors
• CXH 150 includes a heating
element; CXC 150 uses cold
water
Page 16
Wet/Dry Vacuum Versatility
Built to fit into any budget, the Bronco series of vacuums offer both power
and economy.
Featuring 24, 8, and 4-gallon sizes, all Broncos have a powerful 1.34 HP
motor and ample airflow (102 CFM).
All three models include a professional wet/dry attachment tool kit.
The 24 gallon Bronco is available with a front mount squeegee which aids in
large-area wet pick-up.
Each Bronco vacuum includes a professional wet/dry attachment tool kit and
features a one-year warranty.
Page 5
CARPET EXTRACTORS
NEW PRODUCT
Charger Series
Battery Burnishers
Two years ago, we introduced the Charger 2717 DB burnisher, our 27” battery burnisher, which
proved popular among big box retailers. We followed that success the following year with the
Charger 2022 DB, a 20” battery burnisher. At the same time, we introduced our Sulky option,
which was awarded the ISSA 2008 Product Innovation Award at the annual trade show in Las
Vegas.
Charger 2022 ABLT
Easier to Service with Enhanced Durability
• Electronic components are grouped behind the back panel for easy access.
• The digital readout can display service codes to speed problem diagnosis.
• The heavy-duty roller chain and sprockets drive system is extremely reliable.
Greener
• The recyclable 12-gage steel body minimizes waste.
• An enhanced Vac-Trac system captures more pad dust and finish powder.
Even Better Shine
• For a uniform, high-gloss shine, the pad speed and pad pressure are consistently maintained.
• Rugged three-tank carpet spotter
• 100 PSI pump powers solution deep into the nap
• Dual 1-gal/3.8-l solution tanks—separate solution and rinse water
• Dual 2-stage 1.25 HP vacuum motors
• 2.5-gal/9-l detachable recovery tank
• Solid-state circuitry for trouble-free operation
• 55 PSI pump for penetrating stubborn spills
• CXH 100 includes a heating
element; CXC 100 uses cold
water
• Also ideal for upholstery and car detailing
Aero Plus
• Three speeds for maximum drying
performance
• Four positions for drying carpets,
bare floors, upholstered furniture,
and ceilings
• Reduces drying times by up to 50
percent
• Durable rotocast polyethylene
body
• Stacks three high for greater airflow
and efficient storage
For consistent, quiet and safe battery burnishing, the Charger Series is a clear leader in its class.
Greater Convenience
• No operator adjustment is required for a consistent, high-gloss shine.
• The head assembly flips up 90° for more compact storage.
• Pad changes can be made from a standing position.
• Its offset body keeps the operator centered in the workpath for greater visibility.
• A digital readout displays remaining battery charge life.
Spots away
Faster drying—floor to ceiling
To help fit the Charger 2022 ABLT into your budget, we’ve introduced a
24-Volt, 225 AH system. With two fewer batteries, we can make the machine
smaller while keeping everything the same where it really counts... on the floor. We’ve also
optimized the wheel position to make the machine easy to maneuver. To help fit the Charger
2022 ABLT to your operators, we have added an adjustable handle to allow comfortable,
ergonomic operation.
Enhanced Productivity
• The optional sulky attachment provides greater productivity. (DB models only)
• Chargers are available in 20 and 27-inch widths.
Predator CX3
Powerful and
maneuverable
• 8-gal/30-l solution and recovery tanks
Building On Success
This year, we’re taking everything that people love about the Charger burnisher series
and putting it into a value-priced machine. The new Charger 2022 ABLT is a 20”
burnisher designed to fit into the tightest budget. First, and most
importantly, the Charger 2022 ABLT features the same steady-speed
motor controls as the other Charger models. The controller monitors
the motor voltage and keeps it constant giving you the same pad
speed and pressure through the whole job. Second, just like the
other Charger models, the Charger 2022 ABLT has a flip-up head that
allows for ergonomically-correct standing pad changes and easy storage
in small closets.
8-Gallon Predators
Charger 2022 DB
• Optional wheel and folding
transport handle available
PRESSURE WASHERS
NSS’s AquaForce pressure washers include hand-carry
models, cart electrics, and gasoline-powered units. Each
is an exceptional value providing power, ease of use, and
durability.
1500A and 1500 AHT
Electric hand-carry pressure
washer – cold and hot
water models
• 2 HP electric motor • 1500 PSI of water pressure
• Delivers 2 gal/7.5 L per minute
• Ground fault interrupter for
operator safety
• 1500 AHT model accepts water up to 180 degrees F
1000MXDE
25006HX
Electric pressure washer
with cart – hot water
models
Gas-powered mobile pressure
washer – cold water
• 1000 PSI of water pressure
• 2500 PSI of water pressure
• Delivers 2.2 gal/8 L per
minute
• Delivers 3.2 gal/12 L per minute
• Features dual chemical
injection for tough jobs
• Thermal relief valve
• 3-gallon /11-L chemical tank
• Powerful CAT pump; accepts
water up to 180 degrees F
2000GCX
1500AMXDE
Gas-powered mobile pressure
washer – cold water
Electric pressure washer
with cart – cold water
• 2 HP motor
• 1450 PSI of water pressure
• Delivers 2 gal/7.6 L per
minute
• Dual chemical injection
Page 4
• 6.5 HP Honda gas engine
• 5 HP Honda gas engine
• 2000 PSI of water pressure
• Axial pump delivers 3 gal/
11.4 L per minute
• 3-gal chemical injection tank
• Insulated trigger gun, wand and 40-foot hose included
Page 17
ABOUT NSS
TOOLS & ACCESSORIES
Trusted for Nearly a Century
Bare Floor Tool Kit
®
Since 1911, NSS has been helping make the world a
cleaner, healthier, and more comfortable place. As the
only privately owned and operated full line floor care
equipment company in the United States, NSS provides
high quality, heavy-duty commercial and industrial floor
care equipment in the US and 60 countries around the
world.
NSS’s principle-centered leadership has resulted in a
stable enterprise, which operates with core values of
integrity, friendship, and goodwill. These strong beliefs
are reflected in the way we do business every day.
Product Solutions to Meet Real World Demands
Floor & Lite High-Up Kit
Gulper Tool
Squeegee/Bristle Flip Tool
At NSS, we don’t just produce products—we work to
provide our customers with solutions and systems that
deliver real world value. It all begins with our product
development process.
We spend time with our customers and end-users
to understand their issues and needs. We meet with
them, interview them, and observe them in their work
environment. Based on this input, prototype machines
are created and field-tested by real operators. With new
input from the field-testing, we redesign and refine, and
field-test again. The end result is innovative, functional
products which are easy to use and easy to service.
Problem-free Equipment Built to Last
NSS has always employed the philosophy of design
simplicity—uncomplicated solutions that avoid
unnecessary, trouble-prone gadgetry.
Tools & Accessories
Like our machines, NSS tools and accessories are abuseresistant and built to last. Attention to detail, functionality,
and user-friendly operation are hallmarks of our wide array of
tools. Our offering is extensive—you will find unique tools for
specialty applications that can’t be found anywhere else.
Carpet Tools
Just pick up an NSS tool—feel its heft in your hands—to
see the quality difference. In fact, many of our tools are
formed with cast-aluminum bodies and brass fittings and
connectors.
A key feature of NSS tools is their curved uniflow design,
which maximizes airflow and pick-up. Our attention to
ergonomic principles means that NSS tools are designed for
safe and efficient use.
At NSS, we have over 25 tool kits designed to meet different
customer needs. Wet or dry, for ceilings, walls, or floors, we
have a the right kit to help you get your job done more easily,
more quickly, and more safely.
We have confidence in our tools. That’s why many are backed
by a 10-year warranty, which speaks volumes about their life
expectancy and quality of construction.
Ecostrip pads allow damp stripping floors without chemicals.
Just attach to your favorite NSS scrubber and remove the
yellow top coat with just water.
Page 18
That’s why our machines last longer and need fewer
repairs. When repairs are needed, design simplicity
makes NSS machines easy for technicians to service.
The result for our customers is significantly longer
equipment life, less downtime for service and repairs,
and lower machine lifecycle costs. When you purchase
NSS equipment, you are truly making an investment in an
asset that will be around for years to come.
Reliable Delivery and Exceptional Support
Pipe, Wall, and
Shelf Brushes
Super Flex Vacuum Hose
Extended Length Wand
Getting the right equipment where and when it is needed
is critical. That’s why we are diligent to ensure reliable,
on-time, complete delivery of orders.
ISO 9001 certified, our manufacturing facility in Toledo,
Ohio maintains a large inventory of machines that are
ready for shipment. NSS also maintains warehouses in
Connecticut, California, the United Kingdom, the Middle
East, and Asia. Most parts are shipped within 24 hours.
Once our products are in your hands, NSS stands
behind them fully—with highly-trained customer service
personnel, technical support, training seminars, and a
comprehensive warranty. Over 400 Distributors and
Service Centers are authorized to provide field service in
North America.
Do No Harm™
Ecostrip Pads
For more details about NSS or how you can benefit from
our product solutions, call 800-677-1663, or visit us at
www.nss.com.
WARRANTY
Effective for machines purchased after May 1, 2009.
NSS® Enterprises, Inc. Limited Warranty
NSS Enterprises, Inc. (NSS) warrants its new machines against defects in material and workmanship under normal use, service and
maintenance (defined in the NSS Operation and Maintenance Manuals) for the warranty period as detailed below. This warranty is limited to
machines and products that are purchased from an NSS Authorized Distributor or directly from NSS and is limited to the original end-user. Under this
warranty, NSS will repair or replace, at its option, any covered part which is found defective in material or workmanship during the applicable warranty
term. This repair or replacement shall only be performed by an NSS Authorized Distributor or Service Center. All shipping charges for replacement
parts or repaired machines will be the responsibility of the original end-user. When requested, machines and/or parts must be returned to NSS for
inspection to obtain this warranty. NSS reserves the right for final determination of warranty coverage.
The start date of this warranty is the purchase date by the original end-user from an NSS Authorized Distributor or directly from NSS, subject to proof
of purchase. If proof of purchase is not available, the warranty begins six months from the date the machine was shipped from the factory. Parts
repaired or replaced under this warranty are warranted for the remainder of the original warranty period. When covered, a maximum of 4 hours travel
time will be allowed. When out of the continental USA, Labor, Freight and Travel may have different considerations.
NSS will not be liable for any other or additional damages, including but not limited to indirect or special consequential damages arising out of or in
connection with the furnishing, performance, use or inability to use the machine. The buyer agrees and understands that the remedies provided under
this limited warranty are the sole and exclusive remedies available to the buyer. NSS reserves the right to change its warranty policy without notice.
This warranty shall not apply to:
1. Damage incurred during shipment.
2. Any product that has been subject to misuse, abuse, negligence, overloading or accident.
3. Improperly used products or use of the product for other than its intended purpose.
4. Failures due to lack of mandatory maintenance as described in NSS Operation and Maintenance Manuals, Videos and/or Wall Charts.
(e.g., lack of scheduled lubrication or inadequate flushing of chemical solutions.)
5. Any machine modified from its original design (unless authorized by NSS) or repair services performed by non-authorized service centers.
6. Damage or failure resulting from the use of corrosive or incompatible chemicals.
7. Replacement of ordinary wear items including but not limited to: bumpers, belts, carbon motor brushes, electrical components exposed to
moisture, filter bags, hoses, casters, wheels, gaskets, seals, cords, circuit breakers, switches, check valves, solenoids, pumps, squeegee
blades, M-1 fans and fan hoods, and shoes on NSS manufactured cast aluminum tools.
Product
Polyethylene Roto-Molded Tanks & Components
NSS Manufactured Cast Aluminum Tools
Tools and Accessories
On-board Battery Chargers
Batteries
Service Parts for out-of-warranty machines
Autoscrubbers
Champ and Wrangler Series
Burnishers
Charger 2500 & 1500 (cord electric)
Charger 2716, 2717 and 2022 (battery)
Mustang 1500, Galaxy 1500
Commander (Propane)
Floor Machines
Thoroughbred Series
Maverick, Mustang, and Galaxy Series
Sweepers
Manta RS 36, Sidewinder Series
Wet/Dry Vacuums
BP Ranger Series
Colt Series
Bronco Series
Carpet Vacuums
Model M1 “Pig”
Pacer 30, Outlaw B/V, Pacer PB
Pacer 112/115 UE
Pacer 214/218 UE
Carpet Extractors, Spotters and Dryers
Pony 20 SCA, Stallion 8 SC, Stallion 12 SC
Aero Plus
Predator Series
Pressure Washers
AquaForce Series
Parts
10 Years
10 Years
1 Year
2 Years
1 Year
90 Days
Labor
Travel
Exceptions
1 Year
1 Year
6 Months
1 Year
1 Year
6 Months
1 Year
3 Years
1 Year
6 Months
7 Years
3 Years
3 Years
3 Years
1 Year
1 Year
1 Year
1 Year
6 Months
6 Months
6 Months
2 Years parts on Engine, Battery, Fuel System
7 Years
3 Years
1 Year
1 Year
6 Months
1 Year parts for machines with additional weights
1 Year
1 Year
7 Years
3 Years
1 Year
1 Year
1 Year
1 Year
6 Months
7 Years
3 Years
2 Years
1 Year
1 Year
1 Year
1 Year
1 Year
6 Months
3 Years
3 Years
1 Year
1 Year
1 Year
1 Year
1 Year
1 Year
Does not include shoes
Battery mfr’s warranty, contact NSS for referral
6 Months travel for Manta RS 36
1 Year parts on Pacer PB Battery Charger
Includes Belt
2 Years parts on Motors and PC Board
If a problem with NSS equipment develops during the warranty period, first contact your NSS Authorized Distributor or Service Center.
NSS Enterprises, Inc., 3115 Frenchmens Road, Toledo, Ohio 43607-2958 USA (419) 531-2121 www.nss.com Warranty Sheet #9090034 Rev 05/09
NSS European Distribution Centre, Unit 11, Pinfold Trading Estate, 55 Nottingham Road, Stapleford, Nottingham NG9 8AD England (44) 0115 939 1568
Page 19
NSS has always been driven by a belief
that the act of cleaning should “do no
harm” to the environment or our
customer-operators.
Green cleaning your building…
Begins in our factory
Building Green MACHINES
• 100% of raw component shipping materials are reused
• 100% of NSS batteries are recycled and recyclable
• 100% of steel used in product frames is recycled
• NSS filter bags contain 90% filtered paper
• NSS offers high efficiency HEPA filters
• NSS features adjustable water flow for conservation
Green cleaning your building…
Includes your employee’s health
Operator-Friendly Ergonomics
• Handles adjust to match any operator height
• Padded handles increase operator comfort
• All machines are designed to be compact and easy to maneuver
• Carrying handles on vacuums for safe, easy transport
• Flip-up pad drivers make pad replacement easier on the operator’s back
Green cleaning your building…
Includes buying durable equipment
Case Study
If Only This “Pig” Could Talk
In 1940, NSS introduced the now-famous
“Pig” vacuum.
In 1995, at a movie theater in
Indianapolis, we re-discovered a “Pig” in
use a full fifty years after it was
purchased.
A typical upright vacuum lasts about
three years.
Over a fifty year period, this “Pig” kept
about 400 pounds of broken vacuum
cleaners out of the waste stream.
Durability is Green
Heavy-duty construction keeps our equipment at work
in your buildings (and out of landfills) for years.
Stainless-steel hardware makes sure the equipment
can be repaired, when that time finally arrives.
Case Study
Pacer Upright Vacuums
Pacer Upright Vacuums
• CRI Green Label Registered
• HEPA filter standard (112/115)
• GS-42 Green Seal™ Environmental Standard for
Cleaning Services Compliant
Case Study
Wrangler 3330
Wrangler 3330
• Recycled steel in the frame
• Recycled lead in the batteries
• Adjustable water flow
Case Study
Colt 800 PB
Colt 800 PB
• Quiet operation (65 dB)
• Cordless (Safe in traffic areas)
• Recycled lead in the batteries
Case Study
Twister Pads
Twister Pads
• Polish marble, granite and terrazzo
without leaving harsh residue
• NSS is the only manufacturer of
“Twister Approved” equipment
Case Study
Charger 2717 Battery Burnisher
The Charger 2717 is
hitting on all cylinders
when it comes to “Green
Cleaning”
First, it quietly and cleanly
replaces propane.
First, it quietly and cleanly
replaces propane.
Second, it’s ergonomic with a flipup pad change position.
First, it quietly and cleanly
replaces propane.
Second, it’s ergonomic with a flipup pad change position.
Third, it’s built to last and easy to
repair.
NSS has always been driven by a company culture that
respects the environment as well as the safety of our
customer-operators.
We are committed to providing products that Do No
Harm™ as we continue on our mission to contribute to
cleaner, healthier, and more comfortable workplaces.
Thank You
G o t Q u i e t?
For the best in quiet cleaning, try the NSS line of vacuums and sweepers.
When a job has to be done quietly, NSS is the perfect choice.
Pacer 112 UE
Single-Motor Upright Vacuum
Colt 800 PB
Cordless Wet/Dry Vacuum
Only 67 dBA!
That’s 3 dbA
quieter than
Windsor’s
Sensor XP, a
difference you
can hear!
Pacer PB
Cordless PacVac Vacuum
Sidewinder 27 MB
Cordless Sweeper
Only 62 dBA
with front
mount squeegee!
That’s really quiet
cleaning—wet
or dry!
Only 65 dBA!
That’s nearly 25%
quieter (5 dbA) than
Pro-Team’s
Super CoachVac.
Only 67 dBA!
Substantially
quieter than
competitive
battery-powered
sweepers.
For your on-site demonstration, contact your local NSS Distributor
or call NSS directly at 800-677-1663.
Sound energy comparisons based on published data. Exact sound levels depend on background noise and acoustic surroundings.
Pro-Team®, Windsor® and Sensor® are registered tradmarks of their respective companies.
Industrial Grade
For the best in dependable industrial cleaning, try the NSS line of floor cleaning equipment.
When there’s a tough job to be done, NSS is the perfect choice.
Champ 3529
Ride-on Scrubber
• 35-inch/89-cm scrub path with
a 46-inch/117-cm curved Linatex
blade squeegee
• 29-gal./110-l. solution tank and
oversized 32-gal./121-l.
recovery tank
Wrangler 3330 DB
Full-size walk-behind
• 33-inch/84-cm scrub path,
straight urethane or curved
gum-rubber squeegee
• 30-gal./114-l. solution tank;
33-gal./125-l. recovery tank
• 1 HP drive motor with
three forward speeds
• 2.5 HP brush
motor,
220-300
RPM brush
speed
Wrangler 2016 DB
Tight-space walkbehind scrubber
• 20-inch/51-cm
scrub path; straight
or curved squeegee
• 16-gal./61-l. solution
and 17-gal./64-l.
recovery tank
• Two .75 HP brush motors
and a .75 HP vacuum
motor
• .75 HP brush motor
and a .75 HP
vacuum motor
• Six 6-V, 225 or
325 AH batteries
• Low profile side
skirts, bumpers,
and power deck
optional
• Offset scrub head for
superior edge
cleaning
• Battery-powered
wheel drive
Wrangler 2625 DB
Mid-size walk-behind scrubber
• 25-inch/64-cm scrub path, straight
or curved squeegee
• 25-gal./95-l. solution tank; 27-gal./102-l.
recovery tank
• Two .75 HP brush motors and a .75 HP
vacuum motor
• Variable speed propulsion and three scrub pressures
• Compact body designed for maneuverability
For more information, contact your M. D. Stetson Representation.
Industrial Grade
For the best in dependable industrial cleaning, try the NSS line of floor cleaning equipment.
When there’s a tough job to be done, NSS is the perfect choice.
BP-Ranger
Heavy-duty Wet/Dry vacuum
•2
HP 3-stage vacuum motor
• Tip-dispose
• 7-year
transport base
limited warranty
• Front
squeegee and
industrial tools
available
• 55-gal.
drum
mount
available
Sidewinder BP 30
Battery-powered sweeper
Manta RS 36
• Self-propelled,
highly
maneuverable design
• 30-inch/76-cm
• Large,
Ride-on sweeper
• Sweep
large areas
quickly, indoors or
outdoors
total workpath
1.8 cu. ft./51-l. hopper
• 37.4-inch/95-cm
• 12V,
145 AH battery
provides 4.5 hours of
continuous operation
total workpath
• Huge
3 cu. ft./85-l.
hopper
• On-board
battery
charger recharges
anywhere a plug
is available
• Two
12V, 145 AH
batteries provide
up to 2.5 hours
runtime
Model M-1
Carpet vacuum
• All
steel construction
• High
bay cleaning
• 7-year
motor and housing
warranty
• 1.5
bushel dry dirt cleaning
• The
most productive, durable,
and versatile vacuum available.
For more information, contact your M. D. Stetson Representation.
On-Board Battery Charger
Simplified Battery Charging
With on-board battery chargers standard on battery-powered
machines, NSS provides a more consistent, more convenient, and
more reliable solution to battery chargers.
l On-board battery chargers offer charging anywhere that power is
available. By keeping the charger on the machine, damage resulting from
pulling traditional chargers off of the storage shelf is eliminated. Integral
cord wraps and detachable power cords make crushed plugs a thing of
the past.
l For our larger 24V and 36V battery packs, the NSS Dual Pro on-board
battery charger is designed to be the most versatile and easy-touse battery charger we have ever offered. The NSS Dual Pro charger
combines low-frequency charging with a microprocessor controller to
deliver a broad range of performance without any operator intervention.
w
NSS Enterprises, Inc.
3115 Frenchmens Road
Toledo, Ohio 43607-2958
USA
www.nss.com
Printed on Green Seal® certified
paper that contains 30% recycled
post-consumer fiber.
Direct from our factory, this charger can be used on any brand of
flooded lead-acid or AGM battery between 200 AH and 350 AH
without any modifications or algorithm changes. Simply install the
new batteries and the proprietary logic built into the charger will
handle the rest.
w
For Gel batteries between 200 AH and 350 AH, remove a top cover
panel and move a single jumper. A light on the front of the charger
will illuminate, indicating the charger is now ready to accept gel
batteries. No other modifications or algorithm changes are needed.
w
Designed for world-wide use, the charger automatically detects
voltage and frequency of the input current. Rated for 100V, 115V
and 230V at 50 Hz and 60 Hz.
l For our smaller battery packs, NSS offers an SPE high-frequency charger.
This charger is microprocessor controlled and is well suited for 24 V
battery packs below 200 AH.
Dual Pro Specifications
SPE Specifications
DC Output
DC Output
Current-Maximum
24V - 36V
Current-Maximum
25 Amps
12V - 24V
AC Input
AC Input
Voltage-Maximum 24V
9 Amps
Voltage-Maximum 36V
12 Amps
Frequency
Voltage-Nominal
Frequency
50-60
Current-Maximum
12 Amps @ 100 VAC
Current-Nominal
9.5 Amps @ 155 VAC
Current-Maximum
Flooded/AGM or Gel
30% Charge Indicator
LED
60% Charge Indicator
LED
90% Charger Indicator
LED
100% Charger Indicator
LED
AC Power Indicator
100% Charge Indicator
Green LED
Display Indicator
Housing
12 AWG pos output with 3/8 ring
terminal, 12 AWG neg output with
3/8 ring terminal, 18 AWG pos
output interlock with 1/4 Faston
terminal
9 in. (22.8 cm)
Height
8.5 in. (21.6 cm)
Weight
Plastic
Connection
Steel
Length
Warranty
Selection button toggles view
between charging current,
voltage, charging time, amp-hours,
and energy used
Construction
Flash codes (see operation manual)
DC
7 ft. (2 m) 12 AWG cable
AC
IEC 320/C14
Dimensions
Dimensions
Width
Red LED
Yellow LED
Connection
DC
4.5 Amps @ 115 VAC
80% Charge Indicator
Construction
Housing
50-60
2.25 Amps @ 230 VAC
5 Amps @ 230 VAC
Battery Type Indicator
115 / 230
Operation
Operation
Fault Indicator
12 Amps
Length
8 in. (20 cm)
Height
3.25 in. (8.25 cm)
Width
4.75 in. (12 cm)
Weight
4.25 lbs. (2 kg)
Warranty
Two years on new machine
5.5 in. (14 cm)
26 lbs. (11.8 kg)
Three years on new machine
NSS Enterprises, Inc.
3115 Frenchmens Road
Toledo, OH 43607-2958
USA
DISTRIBUTED BY
P: (800) 677-1663
F: (419) 531-3761
[email protected]
www.nss.com
Specifications subject to change without notice.
Printed in USA
©2009 NSS Enterprises, Inc.
#9097173 REV B 2/09
BURNISHERS
SWEEPERS
Charger 2717 DB
Manta RS 36
l On-board battery charger
l Hinged 90° head
l 3.6 HP pad drive motor
l Sweep large areas quickly
l Two 12V, 145 AH batteries
l On-board battery charger
27-in battery burnisher
Charger 2025 DB/AB
20-in battery burnisher
l On-board battery charger
l Wheel-drive or pad-assist
l 2.5 HP pad drive motor
37.4-in ride-on sweeper
Sidewinder 27 MB
27.5-in battery sweeper
l Counter-rotating brushes
l 11.3 dry gallon hopper
l Indoor and outdoor use
All Product Brochure
Sidewinder 27
Charger 1500
20-in cord-electric burnisher
l Burnish, spray buff or scrub
l 1500 RPM
l 1.5 HP pad drive motor
27-in manual sweeper
l 5 times faster than broom
l 1.4 cu ft removable hopper
l Durable and lightweight
P R E S S U R E WA S H E R S
FLOOR MACHINES
AquaForce 1500A
Electric hand-carry washer
Thoroughbred
17or 20-in floor machine
l Durable and dependable
l 175 RPM
l 1 or 1.5 HP motor
l 2 HP electric motor
l 1500 PSI water pressure
l Delivers 2 gal per minute
AquaForce 1000MXDE
Cart-electric washer
l 1000 PSI
l Dual chemical injection
l Delivers 2.2 gal per minute
Mustang Series
17 or 20-in floor machine
l Precision-balanced
l 1 or 1.5 HP motor
l 175-300 RPM available
NSS Enterprises, Inc.
3115 Frenchmens Road Toledo, OH 43607 USA
800-677-1663 www.nss.com
Appearance and specifications subject to change without notice.
N S S
E N T E R P R I S E S ,
I N C .
A U T O M AT I C S C R U B B E R S
C A R P E T VA C U U M S
Champ 2929
Model M-1 “Pig”
l 1 HP drive motor
l 2 HP brush motor, 300 RPM
l 6-6V, 225 or 325 AH batteries
l Legendary durability
l 1.5 HP motor
l 7-year warranty
29-in ride-on scrubber
Portable vacuum
Wrangler 2730 DB
Pacer 30
l 2 0.75 brush motors
l 6-6V, 225 or 325 AH batteries
l On-board battery charger
l Dual 1 HP vacuum motors
l Quiet — only 69 dBA
l HEPA filter available
27 or 33-in walk-behind
30-in wide-area vacuum
Stallion 8SC
16-in self-contained extractor
l 8 gal sol and rec tanks
l 100 PSI solution pump
l Powerful 3-stage vac motor
Predator Series
Tank extractors
l 8 or 12 gal tanks
l Hot or cold models
l Durable polyethylene bodies
W E T / D R Y VA C U U M S
Wrangler 2625 DB
Pacer PB
BP Ranger
l Compact body design
l Variable speed propulsion
l 4-6V, 225 AH batteries
l Vacuums 30,000 per hour
l Ultra quiet — only 65 dBA
l NiMH batteries
l 2 HP vacuum motor
l 12 or 14 gal models available
l 7-year warranty
26-in walk-behind scrubber
Wrangler 2016
20-in walk-behind scrubber
l 0.75 HP brush drive motor
l 0.75 HP vacuum motor
l Wheel-drive or pad-assist
Battery back pack vacuum
Wet/dry vacuums
Pacer 112/115 UE
12 or 15 in upright vacuum
l Powerful 1.5 HP motor
l Lightweight, ergonomic
l Chevron-style brush
Colt Series
Wet/dry vacuums
l 1.23 HP vacuum motor
l 8,12 or 14 gal models available
l Cord-electric or battery models
CARPET EXTRACTORS
Wrangler 2008 AB
17 or 20-in walk-behind
l 0.75 HP brush motor
l 0.5 HP vacuum motor
l Battery or electric models
Pony 20 SCA
Designer Series
l 20 gal sol and rec tanks
l 100 PSI solution pump
l Variable speed propulsion
l 4,7, or 16 gal models
l Solid and versatile
l Includes tool kit
22-in self-contained extractor
Economic wet/dry vacuums
Rugged Gear
For the best in dependable cleaning, try the NSS line of floor cleaning equipment.
When there’s a tough job to be done, NSS is the perfect choice.
Wrangler 1708 /2008
Compact Autoscrubber
• 20-inch
or 17-inch scrub path;
32-inch squeegee
• 8-gal.
solution and 10-gal.
recovery tank
• .75
HP brush motor
and a .5 HP
vacuum motor
Charger 1500
Cord-Electric
Burnisher
Colt 1450 FMS
Heavy-Duty Wet/
Dry Vacuum
• 7-year
limited warranty
• Quiet
operation—
only 62 dbA
• 1500
RPM pad speed for a wet-look shine
• Tip-dispose
tank for easy emptying
• Use
to burnish,
spray buff, or damp scrub
• Includes
front mount squeegee
Model M-1
Carpet Vacuum
• 7-year
• Extra
bag
limited warranty
large 12-gal. filter • The
most productive, durable, and versatile vacuum available
For more information, contact your M. D. Stetson Representative.
Turn over for more rugged machines
Rugged Gear
For the best in dependable cleaning, try the NSS line of floor cleaning equipment.
When there’s a tough job to be done, NSS is the perfect choice.
Wrangler 2016 DB / AB
Mid-Sized Autoscrubber
• Heavy-duty 20-inch
scrubber
• 16-gal.
solution and 17-gal.
recovery tank
• Offset
scrub head for
superior edge cleaning
Pacer 30
Wide-Area Carpet Vacuum
• Powerful dual 1-HP vacuum motors for cleaning muscle
• Quiet—only
Designer 7
Economical Wet/
Dry Vacuum
69 dbA
• Maneuverable
for
easy operation
• Non-corrosive, dent-proof, blow-molded
polyethylene tank
• Includes a standard 10-piece tool kit
• Compact design
Pacer PB
Cordless PacVac
Vacuum
• Unrivaled spot
vacuuming productivity—
up to 30,000 sq. ft. per hour
• Quiet—only 65 dbA—for use anytime
• 1-2 hours runtime per set of NiMH batteries
For more information, contact your M. D. Stetson Representative.
Turn over for more rugged machines
S c h o o l
S o l u t i o n s
HARD FLOORS
charger 1500
DAMP SCRUBBING WITH THE CHARGER 1500
Materials Required
• Charger 1500 burnisher
• Brown or green (medium) scrubbing pads
• Neutral cleaner
• Trigger sprayer for small areas
• Vacuum with hard floor tool or dust mop
Procedure
Prepare Materials
• Check machines to be sure they are in good working order.
• Install a brown or green (medium) pad on the Charger 1500.
• Install a new filter bag in the vacuum, if needed.
• Dilute neutral cleaner according to instructions. Fill the
sprayer. For safety, wear appropriate goggles and gloves.
Prepare the Area
Position Wet Floor signs around the area to be scrubbed.
Pre-sweep The Floor
• Using a vacuum and appropriate hard floor tool, vacuum the area to remove all loose dirt and dust.
If an appropriate vacuum is not available, use a dust mop to pre-sweep the area.
• Use a small putty knife to remove any gum or other items sticking to the floor surface.
Finalize The Plan
• Look at the area to be cleaned to decide where to start. Plan to move away from the electrical
outlet to keep the cord out of your working area.
• Divide the area to be cleaned into imaginary squares about 6 feet by 6 feet.
Scrub Floor
• Start with the Charger close to an outlet.
• Spray the imaginary square closest to the outlet with the neutral cleaner. The floor should be damp
but not wet.
• Turn on the Charger with the pad slightly off the floor surface.
• Lower the pad to the floor and immediately begin scrubbing this area.
• Move the 1500 forward in a straight line, then angle left or right when moving back. (See diagram.)
Repeat to cover the entire square.
• Moving to the next square, continue the process of spraying and scrubbing.
• After all adjacent squares are done, move forward and away from the cord behind you to the next
series of squares.
• Continue this process, pulling the cord along behind you. Check the pad occasionally, flipping or
replacing it as needed.
• Continue until the entire floor is completed.
Put Back Into Service
• Remove the Wet Floor signs.
• Return the equipment to the storage area. Remove the pad and fully wipe down the machine.
school solutions .
economical procedures for clean and healthy learning environments .
Maintaining schools is a complex task. Ongoing budget
pressures and limited staffing further increase this
challenge. NSS has the knowledge and machines to help.
For years, the Model M-1 “Pig” vacuum has
been a favorite for classroom cleaning. It also
allows custodians to clean high-up—vents,
lights, and beams—without a ladder. As a
testament to its quality and durability, the “Pig”
is warranted for 7 years.
For safety and comfort, most gym floors are a unique,
floating design. Large scrubbers, especially ride-ons, may
exceed the floor’s load limits. The result could be damage
to the floor or cracks in the finish. Another key concern is
NSS Enterprises, Inc.
3115 Frenchmens Road
to control the application of water to minimize the risk of
warping. Wrangler 2016 is an incredible mid-sized
scrubber, ideal for cleaning and disinfecting gym floors as
well as myriad other school applications.
The Charger 1500 is the only 1500 rpm burnisher
that can damp scrub. Its unique pad driver has
an inertial steel plate to minimize spikes in the
amp draw, so it won’t overload circuits. No other
machine cleans and shines like the Charger
1500. It also comes with a 7-year warranty.
Toledo, OH 43607
Following the prescribed cleaning procedures will
help maximize results in a minimum amount of
time.
www.NSS.com
800-677-1663
Rev. 0206
S c h o o l
S o l u t i o n s
CLASSROOMS
model m-1 “pig”
S c h o o l
S o l u t i o n s
GYM FLOORS
wrangler 2016 db/ab
CLASSROOM CLEANING WITH THE M-1 “Pig”
GYM FLOOR CLEANING WITH THE WRANGLER 2016 DB/AB*
Materials Required
• Model M-1 “Pig” vacuum
• 10’ Superflex hose
• Aluminum wand
• Appropriate hard floor and carpet tools
• Crevice tool
Materials Required
• Wrangler 2016 AB/DB autoscrubber with standard tool kit (hose, wand and squeegee)
• Neutral floor cleaner with disinfectant
• White or red scrubbing pads (Use white if scrubbing more than once a week, red if scrubbing less frequently.)
• Vacuum and hard floor tool or dust mop for pre-sweeping
• Wet floor signs
Procedure
Prepare Materials
• Check the “Pig” to be sure it is in good working condition.
• Install a new filter bag, if needed.
• Empty the “Scrap Trap” at the front of the machine.
• Store extra tools in the appropriate slots on the tool rack.
Procedure
Prepare Materials
• Check the machine to verify it is in good working order. Inspect the squeegee assembly to be sure
it is clean and clear. Install the squeegee assembly.
• Install a white or red pad on the Wrangler 2016.
• Fill the solution tank with a disinfectant neutral cleaner diluted according to the manufacturer’s directions.
For safety, wear appropriate goggles and gloves.
• Install a new filter bag in the vacuum, if needed.
“Pig” Path:
Wand Cleaning:
Prepare the Area
Position Wet Floor signs at all gym entrances.
Coat
Room
Cleaning the Floor
• Plug the “Pig” into the outlet closest to the classroom door.
• Install the correct tool for the floor surface.
• Start by vacuuming along the base of the front wall, working across the room.
• Turning into the rows of desks, vacuum up each aisle. Only vacuum under half the desks in the row.
Reach with the wand and stretch the hose, being sure the “Pig” stays in the main aisle. (See diagram.)
• Move back across the room, going row by row and vacuuming each aisle. Keep the cord out along the
perimeter of the room.
• After the last row, vacuum down the side aisle to the back wall.
• Turn into the row of desks. Vacuum down each aisle, working towards the far wall.
• Vacuum along the base of the back wall, working back across the room.
• Moving towards the doorway, finish vacuuming the last areas of the room.
• Use a small putty knife to remove any gum or other items sticking to the floor surface.
Clean-up
• Return the equipment to the storage area. Empty the bag and wipe down the machine.
Pre-sweep The Floor
• Using a vacuum and appropriate hard floor tool, vacuum the entire floor to remove all loose dirt and dust.
If an appropriate vacuum is not available, use a dust mop to pre-sweep the floor.
• Use a small putty knife to remove any gum or other items sticking to the floor surface.
Scrub Floor
• Position the 2016 in a corner approximately five (5) feet from each of the walls.
• Turn on the machine and lower the squeegee and pad to the floor. Start with the water flow at the minimum
setting. It is important not to leave standing water on the floor.
• Move forward in a straight line to within three to five feet of the far end of the floor. Make a tight turn with
the machine, being sure to collect all the water with the squeegee. (See diagram.)
• Position the scrub head so that it slightly overlaps the path just cleaned. Continue forward to within three
to five feet of the far end of the floor. Make another tight turn and continue cleaning.
• Follow this process until the last cleaning path is within five (5) feet of the perimeter.
• Clean the perimeter of the floor. Start about five feet
from the walls, overlapping the area already cleaned.
• Move the cleaning path outwards towards the
perimeter with each pass until the entire floor has been
covered.
• On the last lap, clean all the nooks and small areas
around the perimeter with the on-board tool kit.
Put Back Into Service
• Remove the Wet Floor signs.
• Return the equipment to the storage area. Empty the
tanks, remove the pad and squeegee assembly, and
fully wipe down the machine.
* Be sure all chemicals and procedures meet your floor
manufacturers’ or installers’ performance criteria and limitations.
S c h o o l
S o l u t i o n s
CLASSROOMS
model m-1 “pig”
S c h o o l
S o l u t i o n s
GYM FLOORS
wrangler 2016 db/ab
CLASSROOM CLEANING WITH THE M-1 “Pig”
GYM FLOOR CLEANING WITH THE WRANGLER 2016 DB/AB*
Materials Required
• Model M-1 “Pig” vacuum
• 10’ Superflex hose
• Aluminum wand
• Appropriate hard floor and carpet tools
• Crevice tool
Materials Required
• Wrangler 2016 AB/DB autoscrubber with standard tool kit (hose, wand and squeegee)
• Neutral floor cleaner with disinfectant
• White or red scrubbing pads (Use white if scrubbing more than once a week, red if scrubbing less frequently.)
• Vacuum and hard floor tool or dust mop for pre-sweeping
• Wet floor signs
Procedure
Prepare Materials
• Check the “Pig” to be sure it is in good working condition.
• Install a new filter bag, if needed.
• Empty the “Scrap Trap” at the front of the machine.
• Store extra tools in the appropriate slots on the tool rack.
Procedure
Prepare Materials
• Check the machine to verify it is in good working order. Inspect the squeegee assembly to be sure
it is clean and clear. Install the squeegee assembly.
• Install a white or red pad on the Wrangler 2016.
• Fill the solution tank with a disinfectant neutral cleaner diluted according to the manufacturer’s directions.
For safety, wear appropriate goggles and gloves.
• Install a new filter bag in the vacuum, if needed.
“Pig” Path:
Wand Cleaning:
Prepare the Area
Position Wet Floor signs at all gym entrances.
Coat
Room
Cleaning the Floor
• Plug the “Pig” into the outlet closest to the classroom door.
• Install the correct tool for the floor surface.
• Start by vacuuming along the base of the front wall, working across the room.
• Turning into the rows of desks, vacuum up each aisle. Only vacuum under half the desks in the row.
Reach with the wand and stretch the hose, being sure the “Pig” stays in the main aisle. (See diagram.)
• Move back across the room, going row by row and vacuuming each aisle. Keep the cord out along the
perimeter of the room.
• After the last row, vacuum down the side aisle to the back wall.
• Turn into the row of desks. Vacuum down each aisle, working towards the far wall.
• Vacuum along the base of the back wall, working back across the room.
• Moving towards the doorway, finish vacuuming the last areas of the room.
• Use a small putty knife to remove any gum or other items sticking to the floor surface.
Clean-up
• Return the equipment to the storage area. Empty the bag and wipe down the machine.
Pre-sweep The Floor
• Using a vacuum and appropriate hard floor tool, vacuum the entire floor to remove all loose dirt and dust.
If an appropriate vacuum is not available, use a dust mop to pre-sweep the floor.
• Use a small putty knife to remove any gum or other items sticking to the floor surface.
Scrub Floor
• Position the 2016 in a corner approximately five (5) feet from each of the walls.
• Turn on the machine and lower the squeegee and pad to the floor. Start with the water flow at the minimum
setting. It is important not to leave standing water on the floor.
• Move forward in a straight line to within three to five feet of the far end of the floor. Make a tight turn with
the machine, being sure to collect all the water with the squeegee. (See diagram.)
• Position the scrub head so that it slightly overlaps the path just cleaned. Continue forward to within three
to five feet of the far end of the floor. Make another tight turn and continue cleaning.
• Follow this process until the last cleaning path is within five (5) feet of the perimeter.
• Clean the perimeter of the floor. Start about five feet
from the walls, overlapping the area already cleaned.
• Move the cleaning path outwards towards the
perimeter with each pass until the entire floor has been
covered.
• On the last lap, clean all the nooks and small areas
around the perimeter with the on-board tool kit.
Put Back Into Service
• Remove the Wet Floor signs.
• Return the equipment to the storage area. Empty the
tanks, remove the pad and squeegee assembly, and
fully wipe down the machine.
* Be sure all chemicals and procedures meet your floor
manufacturers’ or installers’ performance criteria and limitations.
S c h o o l
S o l u t i o n s
HARD FLOORS
charger 1500
DAMP SCRUBBING WITH THE CHARGER 1500
Materials Required
• Charger 1500 burnisher
• Brown or green (medium) scrubbing pads
• Neutral cleaner
• Trigger sprayer for small areas
• Vacuum with hard floor tool or dust mop
Procedure
Prepare Materials
• Check machines to be sure they are in good working order.
• Install a brown or green (medium) pad on the Charger 1500.
• Install a new filter bag in the vacuum, if needed.
• Dilute neutral cleaner according to instructions. Fill the
sprayer. For safety, wear appropriate goggles and gloves.
Prepare the Area
Position Wet Floor signs around the area to be scrubbed.
Pre-sweep The Floor
• Using a vacuum and appropriate hard floor tool, vacuum the area to remove all loose dirt and dust.
If an appropriate vacuum is not available, use a dust mop to pre-sweep the area.
• Use a small putty knife to remove any gum or other items sticking to the floor surface.
Finalize The Plan
• Look at the area to be cleaned to decide where to start. Plan to move away from the electrical
outlet to keep the cord out of your working area.
• Divide the area to be cleaned into imaginary squares about 6 feet by 6 feet.
Scrub Floor
• Start with the Charger close to an outlet.
• Spray the imaginary square closest to the outlet with the neutral cleaner. The floor should be damp
but not wet.
• Turn on the Charger with the pad slightly off the floor surface.
• Lower the pad to the floor and immediately begin scrubbing this area.
• Move the 1500 forward in a straight line, then angle left or right when moving back. (See diagram.)
Repeat to cover the entire square.
• Moving to the next square, continue the process of spraying and scrubbing.
• After all adjacent squares are done, move forward and away from the cord behind you to the next
series of squares.
• Continue this process, pulling the cord along behind you. Check the pad occasionally, flipping or
replacing it as needed.
• Continue until the entire floor is completed.
Put Back Into Service
• Remove the Wet Floor signs.
• Return the equipment to the storage area. Remove the pad and fully wipe down the machine.
school solutions .
economical procedures for clean and healthy learning environments .
Maintaining schools is a complex task. Ongoing budget
pressures and limited staffing further increase this
challenge. NSS has the knowledge and machines to help.
For years, the Model M-1 “Pig” vacuum has
been a favorite for classroom cleaning. It also
allows custodians to clean high-up—vents,
lights, and beams—without a ladder. As a
testament to its quality and durability, the “Pig”
is warranted for 7 years.
For safety and comfort, most gym floors are a unique,
floating design. Large scrubbers, especially ride-ons, may
exceed the floor’s load limits. The result could be damage
to the floor or cracks in the finish. Another key concern is
NSS Enterprises, Inc.
3115 Frenchmens Road
to control the application of water to minimize the risk of
warping. Wrangler 2016 is an incredible mid-sized
scrubber, ideal for cleaning and disinfecting gym floors as
well as myriad other school applications.
The Charger 1500 is the only 1500 rpm burnisher
that can damp scrub. Its unique pad driver has
an inertial steel plate to minimize spikes in the
amp draw, so it won’t overload circuits. No other
machine cleans and shines like the Charger
1500. It also comes with a 7-year warranty.
Toledo, OH 43607
Following the prescribed cleaning procedures will
help maximize results in a minimum amount of
time.
www.NSS.com
800-677-1663
Rev. 0206
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement