Naim NAC 552, NAC 252, NAC 282, NAC 202, NAC 122x, SUPERNAIT, Nait 5i audio amplifier, NAP 500, NAP 300, NAP 250, NAP 200, NAP 150x, NAP 6-50, NAPV 145, 175 power amplifier, R-com, NARCOM 4 remote control Owner's manual

owners manuaL
P REAM P L I F I ERS
I N T E G RA T E D AM P L I F I ERS , P OWER AM P L I F I ERS
EN G L I S H D EU T S C H F RAN Ç A I S I T A L I AN 0
Contents
PageSection
SAFETY INSTRUCTIONS
E1
1
In order to comply with current European safety regulations
it is essential that the Naim loudspeaker connectors
supplied with amplifiers and loudspeakers are used.
E1
2Mains Power
E2
3
E3
4NAC 552 Introduction and Installation
E4
5NAC 552 Controls and Connections
E5
6NAC 552 Specification
E6
7NAC 252 Introduction and Installation
E6
8NAC 252 Controls and Connections
Equipment must not be exposed to dripping or splashing
and no objects filled with liquid, such as vases, should be
placed on the equipment.
E7
9NAC 252 Specification
E8
10NAC 282 Introduction and Installation
E8
11NAC 282 Controls and Connections
For your own safety do not under any circumstances open
Naim equipment without first disconnecting it from the
mains.
E10
12NAC 282 Specification
E11
13NAC 202 Introduction and Installation
E11
14NAC 202 Controls and Connections
Warning: an apparatus with CLASS I construction shall
be connected to a mains socket outlet with a protective
earthing connection.
E12
15NAC 202 Specification
E13
16NAC 122x Introduction and Installation
E13
17NAC 122x Controls and Connections
Where the mains plug or an appliance coupler is used as
the disconnect device, the disconnect device shall remain
readily operable. To disconnect the equipment from the
mains remove the mains plug from the mains outlet.
E14
18NAC 122x Specification
E15
19
SUPERNAIT Introduction and Installation
E17
20
SUPERNAIT Controls and Connections
E19
21
SUPERNAIT Specification
The following label is attached to all mains powered
equipment:
warning
E20
22
Nait 5i Introduction and Installation
E20
23Nait 5i Controls and Connections
E21
24Nait 5i Specification
E22
25Preamplifier and Integrated Amplifier
Operation
E24
26R-com Remote Handset
E25
27NARCOM 4 Remote Handset
E26
28NAP 500 Installation and Operation
E27
29NAP 500 Connections
E27
30NAP 500 Specification
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
E28
31NAP 300 Installation and Operation
E29
32NAP 300 Connections
E29
33NAP 300 Specification
E30
34NAP 250 Installation and Operation
E30
35NAP 250 Connections
E30
36NAP 250 Specification
E31
37NAPV 145 Installation and Operation
E31
38NAPV 145 Connections
E31
39NAPV 145 Specification
E32
40NAP 200 Installation and Operation
• Reorient or relocate the receiving antenna.
E32
41NAP 200 Connections
• Increase the separation between the equipment and the
receiver.
E32
42NAP 200 Specification
E33
43NAP 150x Installation and Operation
•C
onnect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
E33
44NAP 150x Connections
E33
45NAP 150x Specification
E34
46NAPV 175 Installation and Operation
E34
47NAPV 175 Connections
E34
48NAPV 175 Specification
E35
49NAP 6-50 Installation and Operation
E35
50NAP 6-50 Connections
E35
51NAP 6-50 Specification
E36
52
Do not under any circumstances allow anyone to modify
your Naim equipment without first checking with the factory,
your retailer, or your distributor. Unauthorised modifications
will invalidate your guarantee.
This apparatus
must be earthed
note
This equipment has been tested and found to comply
with the relevant EMC and Safety Standards, and, where
applicable, also complies with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules.
•C
onsult your Naim retailer or an experienced radio/TV
technician for help.
Connections
General Installation
Declarations of Conformity
I n t ro d u ction
Naim Audio products are conceived with performance as the top priority. Careful
installation will help ensure that their full potential is achieved. This manual covers all
preamplifiers, integrated amplifiers and power amplifiers. It begins with some general
installation notes and statutory safety warnings. Product specific information begins in
Section 4.
1 Connections
It is important for both safety and performance that
the standard cables supplied are not modified.
1.1 Interconn e c t C a b l e s
If options are available with your equipment and
installation, DIN interconnect sockets should be used in
the mains lead may not correspond with the coloured
markings identifying the terminals in the plug proceed as
follows:
The wire coloured GREEN-AND-YELLOW must be
connected to the terminal in the plug marked by the
letter E or by the safety earth symbol or coloured GREEN or
GREEN and YELLOW.
preference to RCA Phono sockets. One end of each Naim
The wire coloured BLUE must be connected to the terminal
interconnect cable is marked with a band to establish
in the plug marked with the letter N or coloured BLACK.
its correct orientation. The band denotes the end that
The wire coloured BROWN must be connected to the
connects to the signal source.
terminal in the plug marked with the letter L or coloured
Interconnect plugs and sockets should be kept clean
RED.
and free from corrosion. The easiest way to clean them
is to switch off the equipment, pull the plugs out of their
2.2 Equipment Fuses
sockets, and push them back in again. Contact cleaners
Mains powered Naim Audio equipment is fitted with a
and “enhancers” should not be used as the film they
mains fuse on the rear panel adjacent to the mains input
deposit may degrade the sound.
socket. Replace it if necessary only with the spare fuse
1.2 Loudspea k e r C a b l e s
Loudspeaker cables are vitally important. They should
each be at least 3.5 metres long and of equal length. The
recommended maximum is normally 20 metres although
longer cables may be viable with some Naim amplifiers.
Some Naim amplifiers are designed only to work with
Naim loudspeaker cable and using alternatives may
degrade the performance or even damage the amplifier.
Other Naim amplifiers can be used with any high quality
loudspeaker cable although we recommend that Naim
loudspeaker cable is used. Naim loudspeaker cable is
directional and should be oriented so that the printed
arrow points towards the speakers. The Naim loudspeaker
connectors supplied are designed to comply with
European safety legislation and must be used.
supplied or with an identical fuse. Repeated failure of the
fuse points to a fault that should be investigated by your
retailer or Naim itself.
2.3 Non-rewirable Mains Plugs
If a non-rewirable plug is cut from a mains lead (for
whatever purpose) the plug MUST be disposed of in a
way to render it totally useless. Considerable shock hazard
exists if the cut-off plug is inserted into a mains outlet.
2.4 Mains Circuits and Cables
A hi-fi system usually shares a mains circuit with other
household equipment some of which can cause distortion
of the mains waveform. This distortion can in turn lead to
mechanical hum from mains transformers. Some Naim
transformers are large in size, making them relatively
sensitive to such distortion, and it may be necessary
Contact your local retailer or distributor for further advice
to take account of transformer hum when siting your
on loudspeaker cables and connectors.
equipment.
2 Mains Pow er
Where fused plugs are used 13 amp fuses should be
fitted. Fuses of a lower rating will fail after a period
Transformer hum is not transmitted through the speakers
and has no effect on the performance of the system;
however, a separate mains circuit may reduce it. Such
a circuit (ideally with a 30 or 45 Amp rating) will also
of use. Do not wire voltage dependent resistors or
generally improve system performance. Advice on the
noise suppressors into mains plugs. They degrade the
installation of a separate mains circuit should be sought
mains supply and the sound.
from a qualified electrician.
2.1 Mains Plu g W i r i n g
In some territories a mains plug may need to be fitted
to the supplied mains lead. As the colours of the wires in
Do not substitute alternative mains leads and plugs to
those supplied. They are selected to offer the best possible
performance.
E
I n t ro d u ction
3 General Installation
Naim equipment is designed to offer the finest
In some circumstances, depending on where you live
performance possible avoiding compromise
and the earthing arrangements in your home, you may
wherever practical. This can lead to circumstances
experience radio frequency interference. Controls on
that may be unfamiliar. The notes that follow contain
broadcasting in some territories allow very high levels of
advice specifically related to Naim equipment
as well as more general warnings about the use
of domestic audio products. Please read them
carefully.
3.1 S iting The E q u i p m e n t
In order to reduce the risk of hum audible from the
loudspeakers, power supplies and power amplifiers
should be located a reasonable distance away from
other equipment. The maximum separation distance for
connected equipment is that allowed by the standard
interconnect lead.
radio frequency radiation and both the choice and exact
siting of equipment may be critical. Susceptibility to radio
frequency interference is related to the wide internal
bandwidth necessary for high sound quality. A radio
frequency filter kit is available for some Naim equipment
but sound quality will be progressively compromised as
more elements of the kit are fitted. In situations of extreme
radio interference Naim equipment may be unsuitable.
3.5 Lightning Precautions
Your Naim hi-fi system can be damaged by lightning
and should be turned off and disconnected from the
mains when there is risk of lightning strike. For complete
Some Naim equipment is extremely heavy. Check the
protection all mains plugs and any aerial cables should be
weight of the equipment prior to lifting and if necessary
disconnected when not in use.
use more than one person so that it can be moved safely.
Ensure that your equipment rack or table can easily
3.6 Problems?
support the weight and is stable.
Consumer protection varies from country to country. In
Some speakers and stands are intended to be used with
most territories a retailer must be prepared to take back
floor spikes fitted. Care should be taken when siting and
any equipment he has sold if it cannot be made to work
moving them to avoid personal injury or damage to
satisfactorily. A problem may be due to a fault in the
cables and surfaces. Floor protectors are available from
system or its installation so it is essential to make full use of
your local dealer or distributor to protect non carpeted
your dealer’s diagnostic skills. Please contact your local
floors.
distributor, or Naim Audio directly, if any difficulties cannot
3.2 S witching O n
be resolved.
Some Naim equipment is made in special versions for
Source components and power supplies should be
different territories and this makes it impracticable to
switched on before the power amplifiers. Always switch
arrange international guarantees. Please establish the
amplifiers off and wait a minute before connecting or
local guarantee arrangements with your retailer. Contact
disconnecting any leads. Always use the power switch on
Naim Audio directly for help and advice if necessary.
the product rather than a mains outlet switch.
A “thump” may be heard from the loudspeakers as power
3 . 7 S e r v i c e a n d Up d a t e s
amplifiers are switched on. This is normal, will not cause
It is essential that repairs and updates are only carried
any loudspeaker damage and does not point to any fault
out by an authorised Naim retailer or at the factory by
or problem. A mild “pop” may also be heard shortly after
Naim itself. Many components are custom made, tested
equipment is switched off.
or matched and appropriate replacements are often
3.3 Running I n
Naim equipment takes a considerable time to run in
before it performs at its best. The duration varies, but
under some conditions the sound may continue to
improve for over a month. Better and more consistent
unobtainable from other sources.
Direct contact to Naim for service or update information
should be made initially through Customer Services:
Tel:
+44 (0)1722 426600
Email:
[email protected]
performance will be achieved if the system is left switched
Please quote the product serial number (found on its rear
on for long periods. It is worth remembering however that
panel) in all correspondence.
equipment left connected to the mains can be damaged
by lightning.
E
3.4 Radio Interference
N A C 5 5 2 Preamplifier
4 NAC 552 Introduction and Insta l l a t i o n
The NAC 552 preamplifier does not incorporate an internal power supply and can be used
only in conjunction with the NAC 552PS power supply. Diagram 5.3 illustrates connection
of the NAC 552 to its power supply.
The four transit screws on the underside of the NAC 552 case should be removed before
use and must be replaced if the unit is to be re-packed and shipped. These transit screws
must not be used in any other Naim product. Do not invert the NAC 552 once the transit
screws are removed.
The preamplifier and power supply should be installed on a dedicated equipment
stand intended for the purpose. Do not stand either directly on top of another item of
equipment. Care should be taken to ensure that the preamplifier is level.
Operational features
common to all
preamplifiers and
integrated amplifiers
are described in
Section 25
The preamplifier and power supply should be installed in their final locations before
connecting cables or switching on. Ensure that power amplifiers are switched off and
that the preamplifier volume is turned down before the power supply is switched on. The
power button is located on the power supply front panel.
The units are heavy and care should be taken when lifting or moving them. Make sure
that the surface on which they are to be placed can support their weight.
The following Section 4 paragraphs describe installation features and functions specific to
the NAC 552. Operational features common to all preamplifiers and integrated amplifiers
are described in Section 25.
Both R-Com and NARCOM 4 remote handsets are included with the NAC 552. The R-com
is intended for day-to-day use while the NARCOM 4 can be used for handset-based setup
and programming.
4.1 S ource Inp u t s a n d Re c o r d O u t p u t s
The input selection buttons arranged along the upper
bank select the source signal to be routed to the power
amplifier and the loudspeakers. Below them, in the lower
bank, is a corresponding array of buttons which select the
signal to be routed to the preamplifier’s record outputs.
These separate source and record sections enable one
source (a CD player, for example) to be listened to whilst
the output from another (say, the tuner) is simultaneously
selected for recording.
Note: It is possible to lock the record controls and prevent
accidental de-selection during recording. Record-lock is
switched on or off by pressing the source mono button four
times within six seconds.
Indicators are fitted to the NAC 552 rear panel above
each input socket. These indicators illuminate to provide
information on input selection and on input mapping setup
and programming.
4.2 Input Socket Assignment
Any NAC 552 source input socket can be selected by any
button. For example, while the NAC 552 default setup is for
the CD input button to select input socket No. 2, custom
programming of input assignment could enable any input
socket to be selected by pressing the CD button. Assigning
Input assignment setup is accessed through the NAC
552 program mode. To switch into (or exit from) program
mode press and hold the prog key on the remote handset
(in preamplifier mode). Program mode is indicated by a
flashing indicator on the front panel volume control and
the record selection indicators extinguishing.
Note: If no function is operated within five minutes of
entering program mode the NAC 552 will return to normal
mode automatically.
Any of the six source buttons on the front panel can
be assigned to any of the nine stereo inputs (seven DIN
sockets and two RCA Phono socket pairs) on the rear
panel. In program mode, as a source input is selected, a
rear panel indicator will illuminate to designate the socket
to which it is assigned.
To change the input socket assigned to a source button,
select the source button and use the front panel record
mute and mono buttons to scroll along the input sockets.
If the input socket selected is already assigned to a source
button the indicator above the socket will flash repeatedly.
It is possible to assign one input socket to more than one
source button but NOT to assign multiple input sockets
to one source button. The remote handset record mute
and mono functions can also be used to set up input
assignment.
of each record button follows the corresponding source
button.
E
N A C 5 5 2 Preamplifier
To exit from program mode press and hold the prog key on
the handset until the record select indicators are restored
and the volume indicator stops flashing.
Table 4.3 illustrates the NAC 552 default input assignment.
4.3 S ocket Ty p e s a n d As s i g n m e n t D e f a u l t s
Input SocketSocket Source Button
Number
FeaturesAssignment Default
1
2
3
4
5
6
7
8
9
DIN input
DIN input
DIN input
DIN input/output, unity gain capable
DIN input/output, unity gain capable
DIN input/output
DIN input, power output for phono stage
RCA Phono pair
RCA Phono pair
Not assigned
CD
TUNER
TAPE
AV
AUX 1
AUX 2
Not assigned
Not assigned
5 NAC 552 Controls and Connec t i o n s
5.1 NAC 552 F r o n t
source
bank
record
bank
volume
balance
mono
5.2 NAC 552 R e a r
in 1
in 2
Inputs 1, 2 & 3
nc
nc
ch1
ch2
-ve
E
in 3
in 7
in 4
in 5
in 6
Inputs 4, 5 & 6
ch1
ch2
ch1
(out)
ch2
(out)
-ve
signal ground
Input 7
+ve
ch1
+ve
ch2
-ve
source and record
selection
mute
RC5 in
in 8
in 9
ch 1(L) ch 1(L)
ch 2(R) ch 2(R)
NAC 552PS
NAC 552PS
N A C 5 5 2 Preamplifier
5.3 NAC 552 C o n n e c t e d t o NAC 5 5 2 P S
Note: For best performance the Burndy and 5 pin DIN
cables should be run as close together as possible.
additional signal output
to mono or dual mono
power amplifiers
mains input
and fuse
6 NAC 552/ NAC 552P S Specificat i o n
Input Sensitivities:
75mV, 47kΩ
Overload Margins:
40dB
(all inputs all audio frequencies).
Main Output Level:
0.775V, <50Ω
Tape Output Level:
75mV, 600Ω
Auxiliary Power Outputs:
For Naim phono stage
Dimensions (H x W x D):
Both 87 x 432 x 314mm
Weight:
NAC 552 - 12.9kg
NAC 552PS - 13.9kg
Mains Supply (NAC 552PS):
100-120V or 220-240V, 50/60Hz
cable
direction
marker
to stereo power
amplifiers
Interconnect Cables
NAC 552 Burndy
240° 5 to 5 pin DIN
E
N A C 2 5 2 Preamplifier
7 NAC 252 Introduction and Insta l l a t i o n
The NAC 252 preamplifier does not incorporate an internal power supply and can be used
only in conjunction with the Supercap power supply. Diagram 8.3 illustrates connection of
the NAC 252 to its power supply.
The preamplifier and power supply should be installed on a dedicated equipment
stand intended for the purpose. Do not stand either directly on top of another item of
equipment. Care should be taken to ensure that the preamplifier is level.
The preamplifier and power supply should be installed in their final locations before
connecting cables or switching on. Ensure that power amplifiers are switched off and the
preamplifier volume is turned down before the power supply is switched on. The power
button is located on the power supply front panel.
Operational features
common to all
preamplifiers and
integrated amplifiers
are described in
Section 25
The power supply is heavy and care should be taken when lifting or moving it. Make sure
that the surface on which it is to be placed can support its weight.
The following Section 7 paragraphs describe installation features and functions specific to
the NAC 252. Operational features common to all preamplifiers and integrated amplifiers
are described in Section 25.
7.1 S ource Inp u t s a n d Re c o r d O u t p u t s
The input selection buttons arranged along the upper
bank select the source signal to be routed to the power
amplifier and the loudspeakers. Below them, in the lower
bank, are a corresponding array of buttons which select
the signal to be routed to the preamplifier’s record outputs.
These separate source and record sections enable one
source (a CD player, for example) to be listened to whilst
the output from another (say, the tuner) is simultaneously
Input assignment setup is accessed through the NAC
252 program mode. To switch into (or exit from) program
mode press and hold the prog key on the remote handset
(in preamplifier mode). Program mode is indicated by a
flashing indicator on the front panel volume control and
the record selection indicators extinguishing.
Note: If no function is operated within five minutes of
entering program mode the NAC 252 will return to normal
mode automatically.
Once in program mode press and hold the remote
selected for recording.
Note: It is possible to lock the record controls and prevent
accidental de-selection during recording. Record-lock is
switched on or off by pressing the source mono button four
times within six seconds.
handset 1 key to select or de-select the RCA Phono socket
input for CD, and the remote handset 6 key to select
or de-select the RCA Phono socket input for AUX 2. The
corresponding front panel input buttons can similarly be
used to select or de-select the RCA Phono socket inputs.
7.2 Input Socket Assignment
The NAC 252 has six DIN input sockets and two alternative
pairs of RCA Phono sockets. The RCA Phono sockets can
The appropriate input button indicator will flash three
times on selection of the RCA Phono option and once on
selection of the DIN option.
be assigned individually to the CD and AUX 2 input buttons
To exit from program mode press and hold the prog key on
in place of the DIN sockets.
the handset until the record select indicators are restored
and the volume indicator stops flashing.
8 NAC 252 Controls and Connec t i o n s
8.1 NAC 252 F r o n t
source
bank
record
bank
volume
E
balance
mono
mute
source and record
selection
N A C 2 5 2 Preamplifier
8.2 NAC 252 R e a r
in 1
cd
in 2
tuner
Inputs 1, 2 & 6
nc
nc
ch1
ch2
in 3
tape
in 5
in 6
aux 1 aux 2
in 4
av
-ve
cd/RCA Phono
ch1(L)
ch2(R)
signal in 6 (alternative)
ground
Inputs 3, 4 & 5
ch1
ch2
supercap supercap
ch1
(out)
ch2
(out)
-ve
Input 6
(alternative)
+ve
ch1
+ve
ch2
aux 2/RCA Phono
ch1(L)
ch2(R)
RC5 in
RS232
interface
Note: The NAC 252 AUX 2 input is provided with two
sockets. The lower socket, fitted on delivery with a
blanking cover, is intended for use with a Naim Audio RCA
Phono stage and incorporates an appropriate DC power
supply. The two sockets must not be used simultaneously.
-ve
Note: The RS232/comms interface is an optional
upgrade. It can be specified at time of order or fitted
retrospectively. Contact your local representative or Naim
8.3 NAC 252 C o n n e c t e d t o S u p e r c a p
Audio directly for further information.
Note: For best performance the Burndy and 5 pin DIN
cables should be run as close together as possible.
additional signal output
to mono or dual mono
power amplifiers
mains input
and fuse
9 NAC 252/ Supercap Specificatio n
Input Sensitivities:
Overload Margins:
Main Output Level:
Tape Output Level:
Auxiliary Power Outputs:
Dimensions (H x W x D):
Weight:
Mains Supply (Supercap):
75mV, 47kΩ
40dB
(all inputs all audio frequencies)
0.775V, <50Ω
75mV, 600Ω
For Naim phono stage.
Both 87 x 432 x 314mm
NAC 252 - 7.0kg
Supercap - 11.6kg
100-120V or 220-240V, 50/60Hz
cable
direction
marker
to stereo power
amplifiers
Interconnect Cables
NAC 252 Burndy
240° 5 to 5 pin DIN
E
N A C 2 8 2 Preamplifier
1 0 NAC 282 Introduction and Inst a l l a t i o n
The NAC 282 preamplifier does not incorporate an internal power supply but must be
used in conjunction with either a Naim power amplifier incorporating a preamplifier
power output, or with an appropriate Naim power supply. A separate NAPSC supply that
provides power to the display and control circuits is supplied. Diagrams 11.3 and 11.4
illustrate two NAC 282 power supply options.
Operational features
common to all
preamplifiers and
integrated amplifiers
are described in
Section 25
The preamplifier and power supply should be installed on a dedicated equipment
stand intended for the purpose. Do not stand either directly on top of another item of
equipment. Care should be taken to ensure that the preamplifier is level.
The preamplifier and any power supply should be installed in their final locations before
connecting cables or switching on. Ensure that the preamplifier volume is turned down
before switching on.
The following Section 10 paragraphs describe installation features and functions specific
to the NAC 282. Operational features common to all preamplifiers and integrated
amplifiers are described in Section 25.
10.1 S ource In p u t s a n d Re c o r d O u t p u t s
The input selection buttons arranged along the upper
bank select the source signal to be routed to the power
amplifier and the loudspeakers. Below them, in the lower
bank, are a corresponding array of buttons which select
the signal to be routed to the preamplifier’s record outputs.
These separate source and record sections enable one
source (a CD player, for example) to be listened to whilst
the output from another (say, the tuner) is simultaneously
Input assignment setup is accessed through the NAC
282 program mode. To switch into (or exit from) program
mode press and hold the prog key on the remote handset
(in preamplifier mode). Program mode is indicated by a
flashing indicator on the front panel volume control and
the record selection indicators extinguishing.
Note: If no function is operated within five minutes of
entering program mode the NAC 282 will return to normal
mode automatically.
Once in program mode press and hold the remote
selected for recording.
Note: It is possible to lock the record controls and prevent
accidental de-selection during recording. Record-lock is
switched on or off by depressing the source mono button
four times within six seconds.
handset 1 key to select or de-select the RCA Phono socket
input for CD, and the remote handset 6 key to select
or de-select the RCA Phono socket input for AUX 2. The
corresponding front panel input buttons can similarly be
used to select or de-select the RCA Phono socket inputs.
10.2 Input Socket Assignment
The NAC 282 has six DIN input sockets and two alternative
pairs of RCA Phono sockets. The RCA Phono sockets can
The appropriate input button indicator will flash three
times on selection of the RCA Phono option and once on
selection of the DIN option.
be assigned individually to the CD and AUX 2 input buttons
To exit from program mode press and hold the prog key on
in place of the DIN sockets.
the handset until the record select indicators are restored
and the volume indicator stops flashing.
11 NAC 282 Controls and Connections
11.1 NAC 282 F r o n t
source
bank
record
bank
volume
E
balance
mono
mute
source and record
selection
N A C 2 8 2 Preamplifier
11 .2 NAC 282 Re a r
in 1
cd
in 2
tuner
Inputs 1, 2 & 6
nc
nc
ch1
ch2
-ve
in 3
tape
in 4
av
in 5
in 6
aux 1 aux 2
signal in 6 (alternative)
ground
ch1
(out)
ch2
(out)
cd/RCA
Phono
ch1(L)
ch2(R)
Input 6
(alternative)
Inputs 3, 4 & 5
ch1
ch2
power supply/output option sockets
with link and blanking plugs fitted
+ve
ch1
+ve
ch2
-ve
-ve
RC5 in
to NAPSC
aux 2/RCA
Phono
ch1(L)
ch2(R)
to power
amplifier
with
internal
power
supply
RS232
interface
Note: The NAC 282 AUX 2 input is provided with two
sockets. The lower socket, fitted on delivery with a
blanking cover, is intended for use with a Stageline or
Prefix Phono stage and incorporates an appropriate
DC power supply. The two sockets must not be used
simultaneously.
Note: The RS232/comms interface is an optional
upgrade. It can be specified at time of order or fitted
retrospectively. Contact your local representative or Naim
Audio directly for further information.
11 .3 NAC 282 C o n n e c t e d t o S u p e r c a p a n d NAP S C
additional signal output
to mono or dual mono
power amplifiers
mains input
and fuse
cable
direction
marker
to stereo power
amplifiers
Interconnect Cables
4 to 4 pin DIN
240° 5 to 5 pin DIN
E
N A C 2 8 2 Preamplifier
11 .4 NAC 282 C o n n e c t e d t o H i - C a p a n d NAP S C
to stereo power amplifiers
cable
direction
marker
mains input
and fuse
additional
signal output
to mono or dual
mono power
amplifiers
Note: Alternative upgrade schemes and product
combinations may be feasible. Contact your local
representative or Naim Audio directly for further
information.
1 2 NAC 282 Specification
E10
Input Sensitivities:
75mV, 47kΩ
Overload Margins:
40dB
(all inputs all audio frequencies)
Main Output Level:
0.775V, <50Ω
Tape Output Level:
75mV, 600Ω
Auxiliary Power Outputs:
For Naim phono stage.
Dimensions (H x W x D):
87 x 432 x 314mm
Weight:
7.0kg
Interconnect Cables
240° 5 to 5 pin DIN
N A C 2 0 2 Preamplifier
1 3 NAC 202 Introduction and Inst a l l a t i o n
The NAC 202 preamplifier does not incorporate an internal power supply but must be
used in conjunction with either a Naim power amplifier incorporating a preamplifier
power output, or with an appropriate Naim power supply. A separate NAPSC supply that
provides power to the display and control circuits is also available. Diagram 14.3 illustrates
the NAC 202 connected to a Hi-Cap power supply.
The preamplifier and any power supply should be installed on a dedicated equipment
stand intended for the purpose. Do not stand either directly on top of another item of
equipment. Care should be taken to ensure that the preamplifier is level.
The preamplifier and any power supply should be installed in their final locations before
connecting cables or switching on. Ensure that the preamplifier volume is turned down
before switching on.
Operational features
common to all
preamplifiers and
integrated amplifiers
are described in
Section 25
The following Section 13 paragraphs describe installation features and functions specific
to the NAC 202. Operational features common to all preamplifiers and integrated
amplifiers are described in Section 25.
13.1 Input Sockets and Assignment
The input selection buttons select the source input signal to
be routed to the power amplifier and the loudspeakers.
The NAC 202 has six DIN input sockets and two alternative
pairs of RCA Phono sockets. The RCA Phono sockets can
be assigned individually to the CD and AUX 2 input buttons
in place of the DIN sockets.
Note: If no function is operated within five minutes of
entering program mode the NAC 202 will return to normal
mode automatically.
Once in program mode press and hold the remote
handset 1 button to select or de-select the RCA Phono
socket input for CD, and the remote handset 6 button to
select or de-select the RCA Phono socket input for AUX 2.
The corresponding front panel input buttons can similarly
Input assignment setup is accessed through the NAC
be used to select or de-select the RCA Phono socket
202 program mode. To switch into (or exit from) program
inputs. The appropriate input button indicator will flash
mode press and hold the prog key on the remote handset
three times on selection of the RCA Phono option and
(in preamplifier mode). Program mode is indicated by a
once on selection of the DIN option.
flashing indicator on the front panel volume control.
To exit from program mode press and hold the prog key on
the remote until the volume indicator stops flashing.
14 NAC 202 Controls and Connections
14.1 NAC 202 F r o n t
volume
mon
mute
source selection
E11
N A C 2 0 2 Preamplifier
14.2 NAC 202 Rear
in 1
cd
in 2
tuner
Inputs 1, 2 & 6
nc
nc
ch1
ch2
-ve
in 3
tape
signal in 6
g’nd (alternative)
in 4
av
in 5
in 6
aux 1 aux 2
ch1
(out)
ch2
(out)
cd/RCA
Phono
ch1(L)
ch2(R)
+ve
ch1
+ve
ch2
-ve
RC5 in
to NAPSC
aux 2/RCA
Phono
ch1(L)
ch2(R)
Input 6
(alternative)
Inputs 3, 4 & 5
ch1
ch2
power supply/output option sockets
with link and blanking plugs fitted
to power
amplifier
with
internal
power
supply
RS232
interface
Note: The NAC 202 AUX 2 input is provided with two
sockets. The upper socket, fitted on delivery with a
blanking cover, is intended for use with a Stageline or
-ve
Prefix Phono stage and incorporates an appropriate
DC power supply. The two sockets must not be used
simultaneously.
Note: The RS232/comms interface is an optional
upgrade. It can be specified at time of order or fitted
retrospectively. Contact your local representative or Naim
Audio directly for further information.
14.3 NAC 202 C o n n e c t e d t o H i - C a p a n d NAP S C
to stereo power amplifiers
1 5 NAC 2 0 2 Sp e c i f i c a t i o n
mains input
and fuse
cable
direction
marker
E12
additional
signal output
Interconnect Cables
4 to 4 pin DIN
240° 5 to 5 pin DIN
to mono or dual
mono power
amplifiers
Input Sensitivities:
75mV, 47kΩ
Overload Margins:
40dB
(all inputs all audio frequencies)
Main Output Level:
0.775V, <50Ω
Tape Output Level:
75mV, 600Ω
Auxiliary Power Outputs:
For Naim phono stage.
Dimensions (H x W x D):
87 x 432 x 314mm
Weight:
7.0kg
N A C 1 2 2x Preamplifier
1 6 NAC 122x Introduction and In s t a l l a t i o n
The NAC 122x preamplifier does not incorporate an internal power supply but must be
used in conjunction with either a Naim power amplifier incorporating a preamplifier power
output, or with an appropriate Naim power supply. Diagram 17.3 illustrates the NAC 122x
connected to a Flatcap 2x power supply.
Operational features
common to all
preamplifiers and
integrated amplifiers
are described in
Section 25
The preamplifier and any power supply should be installed on a dedicated equipment
stand intended for the purpose. Do not stand either directly on top of another item of
equipment. Care should be taken to ensure that the preamplifier is level.
The preamplifier and any power supply should be installed in their final locations before
connecting cables or switching on. Ensure that the preamplifier volume is turned down
before switching on.
The following Section 16 paragraphs describe installation features and functions specific
to the NAC 122x. Operational features common to all preamplifiers and integrated
amplifiers are described in Section 25.
16.1 Input S o c k e t s
16.2 Subwoofer Output
The input selection buttons select the source input signal
The NAC 122x provides an analogue subwoofer output via
to be routed to the preamplifier outputs and the power
a pair of RCA Phono sockets.
amplifier.
The NAC 122x has six DIN input sockets and two alternative
Note: The subwoofer output is a duplicate of the main
preamplifier output.
pairs of RCA Phono sockets. The RCA Phono sockets are
permanently connected to the CD and AUX 2 inputs
in parallel with their DIN sockets. RCA Phono and DIN
sockets for the same input should not be connected
simultaneously.
17 NAC 122x Controls and Connections
17.1 NAC 122 x F r o n t
volume
mon
mute
source selection
E13
N A C 1 2 2x Preamplifier
to power amplifier with
internal power supply
17.2 NAC 122 x Re a r
power supply upgrade
link plug fitted
signal ground
RC5 in
RC5 out
to power amplifier with internal power supply
subwoofer RCA Phono out
1cd 2 tun 3 tape 4 AV 5 aux 1 6 aux
in
in in/out in/out in/out 2 in
Inputs 1, 2 & 6
ch1
ch2
6 aux 2 in &
power out
Input 6
(alternative)
Inputs 3, 4 & 5
ch1
(out)
ch2
(out)
ch1
ch2
nc
nc
-ve
cd RCA
Phono in
+ve
ch1
+ve
ch2
-ve
aux 2 RCA
Phono in
RS232
interface
Note: The NAC 122x AUX 2 input is provided with two
sockets. The right hand socket (fitted on delivery with
a blanking cover), is intended for use with a Stageline
or Prefix Phono stage and incorporates an appropriate
DC power supply. The two sockets must not be used
-ve
simultaneously.
Note: The NAC 122x features various technologies to
Note: The RS232/comms interface is an optional
reduce microphonic effects. Some movement of the
upgrade. It can be specified at time of order or fitted
board and sockets when connecting and disconnecting
retrospectively. Contact your local representative or Naim
cables is normal.
Audio directly for further information.
17.3 NAC 122 x C o n n e c t e d t o F l a t c a p 2 x P o w e r S u p p l y
power
switch
mains input
and fuse
to stereo power
amplifiers
1 8 NAC 122x Specification
E14
Input Sensitivities:
75mV, 47kΩ
Overload Margins:
35dB
(all inputs all audio frequencies)
Main Output Level:
0.775V, <50Ω
Tape Output Level:
75mV, 600Ω
Auxiliary Power Outputs:
For Naim phono stage.
Dimensions (H x W x D):
70 x 432 x 301mm
Weight:
3.9kg
cable
direction
marker
to mono or dual
mono power
amplifiers
for CD5x ,
Headline or
phono stage.
Additional
interconnects
required.
Interconnect Cables
4 to 4 pin DIN
240° 5 to 5 pin DIN
S U P E R N AIT Integrated Amplifier
1 9 SUP ERNA IT Introduction and In s t a l l a t i o n
The Supernait should be installed on a dedicated equipment stand intended for the
purpose. Do not stand it directly on top of another item of equipment. Care should
be taken to ensure that it is level. The amplifier should be installed in its final location
before connecting cables or switching on. Ensure that the volume is turned down before
switching on.
A variety of power supply upgrade, alternative preamplifier and alternative or additional
power amplifier options are possible for the Supernait. Diagrams illustrating the connection
of some of these are shown in Section 20.
The following Section 19 paragraphs describe installation features and functions specific
to the Supernait. Operational features common to all preamplifiers and integrated
amplifiers are described in Section 25.
19.1 Source Input Selection and Assignment
Operational features
common to all
preamplifiers and
integrated amplifiers
are described in
Section 25
19.1.2 Digital Inputs
The input selection buttons arranged along the upper
The Supernait additionally provides four S/PDIF digital input
bank select the source signal to be routed to the power
sockets - 2 RCA Phono coaxial and 2 “Toslink” optical - on
amplifier and the loudspeakers. The six buttons are labelled
the rear panel. Any input selection button can be assigned
cd, tuner, tape, av, aux1 and aux2.
to one of these sockets.
Each input button may be assigned to analogue inputs
Note: The digital inputs support stereo PCM audio only. If
(via DIN, RCA Phono or 3.5mm jack sockets), or to digital
the digital signal contains anything other than stereo PCM
inputs via RCA Phono coaxial, “Toslink” or “mini-toslink”
audio (Dolby or DTS encoded programme material for
optical sockets. The default settings and the assignment
example) all outputs will be muted.
setup procedure are detailed in Sections 19.2 and 19.3
respectively.
19.1.3 Front Panel Combined Input
An auxiliary front panel input socket is also provided. This
19.1.1 Analogue Inputs
socket is a 3.5mm analogue “jack” input combined with
The first four selection buttons (cd, tuner, tape and av) can
a digital “mini-Toslink” optical socket. The analogue input
each be assigned to both a DIN input socket and a pair of
is wired internally in parallel with the rear panel aux1 input
RCA Phono input sockets on the rear panel. The DIN and
and the two must not be connected simultaneously.
Phono sockets for each input are internally wired in parallel
and should not be connected simultaneously.
The front panel input (analogue or digital) is automatically
selected (and the aux1 selection button automatically
The aux1 and aux2 selection buttons can each be
assigned to a pair of RCA Phono input sockets and a DIN
input socket on the rear panel respectively.
assigned to it), whenever a plug is inserted in the socket.
Note: The Supernait is able to differentiate a digital source
from an analogue one at the front panel input if the digital
Note: The aux2 DIN input socket carries a power supply
output voltage appropriate for a Naim phono preamplifier.
source is working when the plug is inserted.
Input selection will revert to that previously selected when
the front panel input plug is removed.
19.2 Default Input Selection Button and Input Socket Assignment
Input Selection
Input Socket ButtonAssignment
Input Socket
Type
cd
Analogue Input 1
DIN/RCA Phono
tuner
Analogue Input 2
DIN/RCA Phono
tape
Digital Input 1
RCA Phono Coax
av
Analogue Input 4
DIN/RCA Phono
aux1
(See Note)
Digital Input 2
“Toslink” Optical
aux2
Analogue Input 6
DIN (with Naim phono stage power supply)
Note: Any plug inserted into the front panel socket will automatically provoke selection of
this input (digital or analogue) and will automatically assign it to the aux1 selection button.
E15
S U P E R N AIT Integrated Amplifier
19.3 Digital Input Assignment
The default digital input socket assignment illustrated in
A stereo set of speaker connection sockets is provided
Table 19.2 may be changed if desired. Each selection
on the rear panel. Custom Naim Audio loudspeaker
button may be assigned to any one of the four rear panel
connectors are supplied to make the connection and in
digital input sockets.
order to comply with current European safety regulations
Input assignment setup is accessed through the Supernait
program mode. To switch into (or exit from) program mode
press and hold the prog key on the remote handset (in
preamplifier mode). Program mode is indicated by a
flashing indicator on the front panel volume control.
Note: If no function is operated within five minutes of
entering program mode the Supernait will return to normal
mode automatically.
Once in program mode, to assign a digital input socket,
first press the required input selection button. Then, press
one of the record selection buttons to assign the desired
digital input. The record selection buttons assign digital
inputs as set out in the following table:
these should always be used. Naim Audio speaker cable
will provide the best results; however, a wide range of
speaker cable types can be used without risk of damage
to the amplifier.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
orientation at both the speaker and amplifier ends of the
cable is the same for both channels.
19.6 Headphone Output
A 3.5mm headphone socket is provided on the front
panel. Insertion of a headphone plug will automatically
switch on the headphone amplifier and mute the speaker
outputs unless the Supernait is set up not to mute.
Record Select Button
Digital Input Selection
cd
(assigns)
digital 1 (coaxial)
enter program mode and press the record aux2 selection
tuner
(assigns)
digital 2 (optical)
button.
tape
(assigns)
digital 3 (coaxial)
av
(assigns)
digital 4 (optical)
As an example, to assign the tuner input selection button
to digital input 4 proceed as follows.
i) Enter program mode.
ii) Press the tuner input selection button.
To prevent (or re-enable) automatic speaker muting,
1 9 . 7 A u x i l i a r y I n p u t s a n d Ou t p u t s
A bi-amp out (preamplifier output) DIN socket is provided
on the rear panel to enable an external upgrade power
amplifier or second (bi-amp) power amplifier to be used.
Note: Bi-amp out is the preferred socket for all external
iii) Press the av record selection button (which will
power amplifier connections.
illuminate).
Also provided are separate pre-amp out and power-amp
iv) Exit program mode.
in sockets. In normal use these sockets are connected by
To return an input selection button to its default analogue
an external link plug. The link plug should be removed only
input, repeat the assignment procedure.
For example, to return the tuner input selection button to its
analogue input socket.
i) Enter program mode.
ii) Press the tuner input selection button.
iii) Press the av (illuminated) record selection button (which
will extinguish).
iv) Exit program mode.
19.4 Record Outputs
The selection buttons arranged along the lower bank
if a power supply upgrade is to be used or an alternative
preamplifier is to use the Supernait power amplifier section.
Diagrams 20.3 to 20.5 illustrate use of these sockets.
When an external preamplifier is connected to the
Supernait power-amp in socket, a fault will initially be
indicated by the source mute button flashing. To clear the
fault, press and hold the flashing source mute button. This
will un-mute the power amplifier and turn off the display
and volume and balance indicators.
The Supernait provides an unfiltered analogue stereo
subwoofer output via a pair of RCA Phono sockets.
select the source signal to be routed to the Supernait’s
Note: The subwoofer output is a duplicate of the
record outputs.
preamplifier output. No low-pass filtering is applied.
These separate source and record sections enable one
source (a CD player, for example) to be listened to whilst
the output from another (say, the tuner) is simultaneously
selected for recording.
Note: Simultaneous and independent listen and record is
not possible with two digital sources.
E16
19.5 Speaker Outputs
1 9 . 8 P o w e r S u p p l y Up g r a d e s
The Supernait preamplifier section can be upgraded
through the connection of an external Flatcap 2x, Hi-Cap
or Supercap power supply. Diagrams illustrating power
supply upgrades are shown in the following section. The
S U P E R N AIT Integrated Amplifier
Supernait and external power supply must be switched
should always be connected regardless of what other
off when connections are made. Switch on the external
equipment is used in conjunction with the amplifier. The
power supply and then the Supernait when all connections
mains earth only grounds the case and the electrostatic
are complete.
screen within the transformer, and is not connected to the
signal negative. In order to avoid hum loops, the signal
19.9 General C o n n e c t i o n s N o t e s
negative of the whole system should be connected to the
The Supernait negative input and output connections for
mains earth (ground) in one place.
each channel are common. The mains earth (ground)
20 SUPERNAIT Controls and Connections
source and record
selection
20.1 SUP ERNA I T F r o n t
source
bank
record
bank
volume
balance
mute
digital
inputs
20 .2 SU P ERNA I T R e a r
power
mains
input
and fuse
left
RS232
interface speaker
cd and tuner
Inputs
ch1
ch2
RC5 in/out
nc
nc
-ve
tape and av
Inputs
ch1
(out)
ch2
(out)
ch1
ch2
-ve
outputs
headphone
output
analogue
Phono RCA
inputs
1 2 3 4 bi-amp sub tape aux1 av tape tuner cd
signal ground
power amp in and
preamp out. Link
plug fitted.
right
speaker
combined
analogue and
digital input
aux 2 av in tape tuner cd in
in & & out in & in
power
out
out
aux 2 input
+ve
ch1
+ve
ch2
Note: The RS232 interface is an optional upgrade. It can
-ve
be specified at time of order or fitted retrospectively.
Contact your local representative or Naim Audio directly
pre-amp out for
bi-amp
ch2
-ve
ch1
nc
for further information.
Note: The link plug should be removed only if a power
supply upgrade is to be used or an alternative preamplifier
is to use the Supernait power amplifier section. It should
remain fitted in all other circumstances.
E17
S U P E R N AIT Integrated Amplifier
20.3 SUP ERNA I T C o n n e c t e d t o H i - C a p P o w e r S u p p l y
power
mains
input
and fuse
cable
direction
marker
Interconnect Cables
4 to 4 pin DIN
240° 5 to 5 pin DIN
mains input
and fuse
20.4 SUP ERNA I T C o n n e c t e d t o NAP 2 0 0 P o w e r A m p l i f i e r
power
mains
input
and fuse
mains input
and fuse
E18
cable
direction
marker
Interconnect Cables
4 to 4 pin DIN
S U P E R N AIT Integrated Amplifier
20.5 SUP ERNA I T C o n n e c t e d t o H i - C a p P o w e r S u p p l y a n d NAP 2 0 0 P o w e r A m plifier
power
mains
input
and fuse
cable
direction
marker
Interconnect Cables
4 to 4 pin DIN
240° 5 to 5 pin DIN
mains input
and fuse
mains input
and fuse
2 1 SUPERNAI T Sp e c i f i c a t i o n
Input Sensitivities:
75mV, 47kΩ
Overload Margins:
40dB
(all inputs all audio frequencies)
Preamp Output Level:
0.775V, <50Ω
Tape Output Level:
75mV, 600Ω
Power Output:
Continuous 80 Watts per channel into 8 Ohms
Auxiliary Power Outputs:
For Naim phono stage
Quiescent Consumption:
10VA
Dimensions (H x W x D):
87 x 432 x 314mm
Weight:
12.8kg
Mains Supply:
100-120V or 220-240V, 50/60Hz
E19
N A I T 5 i I ntegrated Amplifier
2 2 NAIT 5i In troduction and Insta l l a t i o n
The Nait 5i should be installed on a dedicated equipment stand intended for the
purpose. Do not stand it directly on top of another item of equipment. Care should
be taken to ensure that it is level. The amplifier should be installed in its final location
before connecting cables or switching on. Ensure that the volume is turned down before
switching on.
The following Section 22 paragraphs describe installation features and functions specific
to the Nait 5i. Operational features common to all preamplifiers and integrated amplifiers
are described in Section 25.
22.1 Inputs
Operational features
common to all
preamplifiers and
integrated amplifiers
are described in
Section 25
22.2 Outputs
The front panel input selector buttons select the source
A stereo set of speaker connection sockets is provided
input signal to be routed to the power amplifier and the
on the rear panel. The sockets can accept standard
loudspeakers. The four buttons are labelled cd, tuner, tape
4mm plugs, but to comply with European legislation the
and av. Each input button corresponds to a pair of rear
Naim connectors supplied should be used. Naim Audio
panel RCA Phono input sockets. The cd and tuner inputs
speaker cable will provide the best results; however, a wide
are additionally provided with alternative DIN sockets.
range of speaker cable types can be used without risk of
These should be used in preference to the RCA Phono
damage to the amplifier.
sockets if practical. Do not connect both the DIN and
Ensure when connecting speakers that they are “in
RCA Phono sockets of one input simultaneously.
phase”. That is, the positive and negative connection
orientation at both the speaker and amplifier ends of the
cable is the same for both channels.
The tape output always carries the selected input signal.
No “record monitor” function is available.
23 NAIT 5i Controls and Connections
23.1 NAIT 5i F r o n t
volume
E20
source selection
N A I T 5 i I ntegrated Amplifier
23.2 NAIT 5i R e a r
power
mains
input
and fuse
left
speaker
tuner input (RCA Phono)
tuner input (DIN)
right
speaker
Note: The Nait 5i features various technologies to reduce
microphonic effects. Some movement of the board and
sockets when connecting and disconnecting cables is
normal.
2 4 NAIT 5i S pecification
Input Sensitivities:
225mV, 20kΩ
Overload Margins:
35dB
(all inputs all audio frequencies)
Tape Output Level:
225mV, 100Ω
Power Output:
Continuous 50 Watts per channel into 8 Ohms
Quiescent Consumption:
10VA
Dimensions (H x W x D):
70 x 432 x 301mm
Weight:
6.4kg
Mains Supply:
100-120V or 220-240V, 50/60Hz
av in
tape in
tape out
CD input (DIN)
CD input (RCA
Phono)
cd and tuner
Inputs
ch1
ch2
nc
nc
-ve
E21
P re a m p lifier and Integrated Amplifier Operatio n
2 5 Preamplifier and Integrated Am p l i f i e r O p e r a t i o n
Many operational and control features of Naim preamplifiers and integrated amplifiers
are common to all and are based on a similar user interface. This section of the manual
describes those features and the user interface, drawing attention to differences between
products where they occur. Table 25.10 sets out some variations in user interface between
products.
Front panel controls are duplicated on the remote control handset which may also
provide some extra functions. See Sections 26 and 27 for more information.
For the purposes of brevity the term preamplifier in the following paragraphs can be taken
also to mean integrated amplifier.
25.1 A utomat i c I n p u t Sw i t c h i n g
With Automatic Input Switching engaged the appropriate
source input will be selected as soon as any handset function
for that (Naim) source component is operated. For example,
if the tuner input is selected and the cd play key is pressed on
the handset, the preamplifier will automatically switch to the
cd input. Automatic Input Switching can be programmed to
program mode by pressing and holding the handset prog
key (with the handset in preamplifier mode). The front
panel source mute button (NAC 202, and NAC 122x, mute
button, Nait 5i av input button) will illuminate if Unity Gain
is selected. If it is not enabled it can be switched on by
pressing the same button twice.
operate on any combination of the cd, av and tuner input
With Unity Gain enabled on the NAC 552, pressing the
buttons (and sockets to which they are assigned).
source mute button again will reveal the inputs selected
To enable Automatic Input Switching, first switch the
preamplifier into program mode by pressing and holding
the handset prog key (with the handset in preamplifier
mode). The front panel source mono/mon button (NAC
202 and NAC 122x mon button, Supernait record mute
button and Nait 5i tape button) will illuminate if automatic
switching is already enabled. If it is not enabled it can be
switched on by pressing the same button.
With automatic switching enabled, pressing the button
by their indicators illuminating for a short time. Repeated
operation of the button will sequentially select each
combination of the available inputs, and Unity Gain
disabled. When the desired inputs are indicated, stop
pressing the button. The selected inputs will then be
enabled for Unity Gain. The handset can also be used to
select Unity Gain. See table 25.10.
Unity Gain only becomes operational on exit from program
mode by pressing and holding the handset prog key.
again will reveal the inputs selected for auto switching
Note: The Unity Gain feature must be used with care. It
by their indicators illuminating for a short time. Repeated
effectively by-passes the preamplifier volume and balance
operation of the button will sequentially select through
controls leaving any signal connected to a Unity Gain
each possible combination of cd, tuner, av inputs, and auto
input to be passed to the power amplifier and speakers at
switching disabled (all indicators off). When the desired
full volume. In order to reduce the potential for inadvertent
inputs selected for auto switching are indicated, stop
mishap, any subsequent modifications to input assignment
pressing the button. The remote handset can also be used
will automatically disable previously set up Unity Gain
to engage Automatic Input Switching. See Table 25.10.
inputs. Additionally, if an input is selected which has Unity
Automatic Input Switching only becomes operational
on exit from program mode by pressing and holding the
handset prog key.
Note: In a few cases some further equipment configuration
Gain enabled, the preamplifier volume and balance
handset functions will be disabled and their indicators will
turn off. This will be flagged by the volume or balance
indicators flashing if either handset function is operated.
may be required for auto switching to operate correctly.
25.3 Handset Volume and Balance Control
Please contact your retailer or local distributor for advice.
The remote handset volume and balance keys provide
25.2 A V Integ r a t i o n (U n i t y G a i n )
some alternative control characteristics. A quick press and
release of a key will adjust by a preset “nudge”. A quick
Unity Gain enables an audio-visual processor to be
press and release of a key followed by press and hold will
integrated such that its volume control takes over command
cause continual slow adjustment. Simple press and hold will
of signals connected to selected preamplifier inputs. On the
cause continual fast adjustment.
NAC 552 Unity Gain may be selected on DIN input sockets
that carry both inputs and outputs (the corresponding input
buttons may depend on the input assignment). On all other
preamplifiers it may be selected on only the av input.
E22
To select Unity Gain, first switch the preamplifier into
Note: The NAC 122x and Nait 5i do not incorporate any
facility for channel balance control.
P re a m p lifier and Integrated Amplifier Operatio n
25.4 Mute, Mo n o a n d M o n
25.6 Switch-on
Mute silences the output signal and can be selected by
After switch-on, via the power amplifier or power supply
pressing the front panel mute button. On preamplifiers
power button, the preamplifier will remain muted for 30
equipped with separate source and record sections Mute
seconds while control systems and circuits stabilise. On
can be selected independently for source and record.
preamplifiers equipped with separate source and record
Mute can also be selected from the handset.
sections, only the source side will un-mute automatically
Note: The Nait 5i does not incorporate any front panel
mute facility.
leaving the record side muted.
25.7 Remote Control
Some preamplifiers include a mon (mono) function that
sums the left and right channels. Mono can be selected by
pressing the front panel mon (NAC 552 mono) button. On
preamplifiers equipped with separate source and record
sections mono can be selected independently for source
and record. Mono can also be selected from the handset.
The remote handset supplied with the preamplifier
duplicates all configuration and control functions. See
Sections 26 and 27 for more information.
25.8 Defaults
To restore all programmable settings to the factory defaults
Note: The NAC 202, NAC 122x, Supernait and Nait 5i do not
press and hold the remote handset disp key while the
incorporate any mono facility.
preamplifier is in program mode. The preamplifier will exit
On preamplifiers that do not incorporate separate source
from program mode following this operation.
and record sections a mon (“tape monitor”) facility is
provided. Pressing the mon button routes the tape input
signal to the preamplifier output while leaving the input
25.9 Fault Conditions
Some preamplifiers will indicate problems by flashing front
selection routed to the tape output. Tape monitor can also
panel button indicators.
be selected from the handset.
On the NAC 252, NAC 282, NAC 202, and Supernait, a
Note: The Nait 5i does not incorporate any front panel
flashing source mute button indicates that a power supply
tape monitor facility.
or link plug is incorrectly installed.
On the Supernait, a flashing record mute button indicates
25.5 Display
an “over-current” condition.
The preamplifier front panel button illumination can
On the Nait 5i, a flashing cd button indicates an “over-
be switched off by pressing the remote handset (in
preamplifier mode) disp function. Any subsequent handset
or front panel operation will temporarily restore the display.
temperature” condition and a flashing tuner button
indicates an “over current” condition.
A second operation of the disp function will restore the
display.
25.10 Interfac e F u n c t i o n B u t t o n s a n d K e y s
Product
ProgramAuto InputAV IntegrationRestore
ModeSwitching
(Unity Gain)
Defaults
NAC 552
hold preN/AN/AN/A
handset key (R-com)
hold prog
pre 4 mon
source mono
pre 4 mute
hold disp
source mute
handset key(s) (NARCOM 4)
front panel
NAC 252
hold prog
pre 4 mon
source mon
pre 4 mute
hold disp
source mute
handset key(s) (NARCOM 4)
front panel button
NAC 282
hold prog
pre 4 mon
source mon
pre 4 mute
hold disp
source mute
handset key(s) (NARCOM 4)
front panel button
NAC 202
hold prog
pre 4 mon
mon
pre 4 mute
hold disp
mute
handset key(s) (NARCOM 4)
front panel button
NAC 122x
hold prog
pre 4 mon
mon
pre 4 mute
hold disp
mute
handset key(s) (NARCOM 4)
front panel button
Supernait
hold prog
rec 4 mute
record mute
pre 4 mute
hold disp
source mute
handset key(s) (NARCOM 4)
front panel button
Nait 5i
hold prog
pre 4 3
tape
pre 4 4
hold disp
av
handset key(s) (NARCOM 4)
front panel button
Note: The handset must be in preamplifier mode to select
program mode or to restore defaults
Note: The 4 symbol means one key followed by another.
E23
R - c o m Remote Handset
2 6 R-com R emote Handset
The R-com remote handset is supplied with the NAC 552 and CD555 and can be
purchased as an accessory. It offers quick and intuitive control of the most often used
functions of CD players, preamplifiers, integrated amplifiers and tuners.
To fit batteries, remove the bottom end cover using the tool provided and insert the
batteries into the body taking care with their orientation. Replace the end cover. Remove
the batteries if the R-com is to be packed and shipped.
26.1 Using R-c o m
R-com keys primarily provide control of the functions
most often used on CD players, preamplifiers, integrated
amplifiers and tuners. In order to extend battery life, R-com
will enter a “sleep” mode when unused. It will “wake” on
being touched.
R-com has three operational modes - CD Player mode,
the pre key. Program mode functions can then be
accessed from the equipment front panel.
In Tuner mode (press tun key) the following keys will
change function:
disp:Switches the tuner front panel button indicators
off and on.
Preamplifier/Integrated amplifier mode and Tuner mode.
prev:
Selects the tuner “down” function.
Its default mode is CD player. When awake in CD Player
next:
Selects the tuner “up” function.
mode, all R-com keys will illuminate green. To switch the
R-com into Preamplifier/Integrated amplifier mode or Tuner
26.2 R-com Keys
mode press the pre or tun keys respectively. The pre or tun
key will then illuminate white. To switch R-com back into
CD player mode either press the pre or tun key again.
In default mode the R-com keys have the following
functions:
disp
open
stop
play
prev
next
disp:Switches the CD player front panel indicators off
and on.
open:
Opens the door on the CD555.
stop:
Stops CD replay.
play:
Begins CD replay.
prev:
Selects the previous track or index point.
next:
Selects the next track or index point.
vol +
vol -
vol +:Increases the preamplifier/integrated amplifier
volume.
mute
pause
pre
tun
vol –:Decreases the preamplifier/integrated amplifier
volume.
mute:Reduces the volume to zero. A second press
restores the volume.
pause: Pauses CD replay. A second press restores play.
In Preamplifier/Integrated amplifier mode (press pre key),
the following keys will change function:
disp:Switches the preamplifier/integrated amplifier
front panel button indicators & knob indicators off
and on.
prev:
Selects the previous source input.
next:
Selects the next source input.
Note: Preamplifier or integrated amplifier program mode
can be selected from the R-com by pressing and holding
E24
N A R C O M 4 Remote Handset
2 7 NAR COM 4 Remote Handset
The NARCOM 4 remote handset is supplied with the NAC 552, NAC 252, NAC 282, NAC
202, NAC 122x, Supernait and Nait 5i. It is a multi-functional remote control handset
designed to be used with Naim Audio CD players, integrated amplifiers, preamplifiers,
preset tuners and subwoofers.
To fit batteries, remove the battery cover and insert the batteries into the body taking care
with their orientation. Replace the battery cover.
27.1 Using NARC OM
2 7 . 2 NAR C OM 4 K e y s
Operation of the NARCOM 4 handset is based around
three types of keys: System Component Keys, Global Keys
and Soft Keys.
Disp Key (Soft)
System Component Keys keys switch the operation of
the Soft Keys into modes appropriate to each system
Numeric keys (Soft)
component (CD player, preamplifier, etc.).
Global Keys operate specific component functions
regardless of the System Component Key setting and are
available at all times.
System Component Keys
Preamplifier and Integrated Amplifier Global Keys operate
as follows:
Global Keys (CD)
vol (5 & 6) Adjusts the preamplifier volume and the
volume control position.
muteReduces the preamplifier volume to zero. A
second press restores the volume.
Volume and mute keys
bal (3 & 4)Adjusts the channel balance. Some
Naim amplifiers have control of channel
Prog Key (Soft)
balance available only from the remote
handset. On these products the balance
will automatically centre as it reaches
the mid point. Centring is indicated by a
flashing volume control indicator. To resume
adjustment once the balance has centred,
the bal key must be released and repressed.
monEnables the output of a tape recorder to
be heard while recording. The source to be
recorded is chosen by the input selection
buttons in the normal way. A second
operation of the mon key restores normal
operation. Mon alternatively operates the
mono function on appropriately equipped
preamplifiers.
Preamplifier and Integrated Amplifier Soft Keys operate as
follows:
dispSwitches the front panel button indicators off
and on.
progPress and hold to switch the preamplifier or
integrated amplifier into program mode.
numericEnables direct selection of source inputs.
E25
N A P 5 0 0 Power Amplifier
2 8 Installation and Operation
The NAP 500 and NAP 500PS should be installed on a dedicated equipment stand
intended for the purpose and should be in their final location before connecting cables or
switching on. Switch on the source and preamplifier components, with the volume turned
down, before switching on the NAP 500. The NAP 500 power button is located on the front
panel of the NAP 500PS Power Supply.
Care should be taken when siting the NAP 500 to ensure that the top and bottom
ventilation grids are not blocked.
The NAP 500 and NAP 500PS are very heavy and care should be taken when lifting or
moving them. Make sure that the surface they are to be placed on can support the full
weight.
28.1 General C o n n e c t i o n s No t e s
The negative input and output connections for each
Only Naim Audio speaker cable should be used to
channel are common. The mains earth (ground) should
connect a loudspeaker to the output of the NAP 500.
always be connected regardless of what other equipment
Custom Naim Audio loudspeaker connectors are supplied
is used in conjunction with Naim power amplifiers. This only
to make the connection and in order to comply with
grounds the case and the electrostatic screen within the
current European safety regulations these should always
transformer, and is not connected to the signal negative.
be used.
In order to avoid hum loops, the signal negative of the
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
whole system should be connected to the mains earth
(ground) in one place.
Note: Each channel of the NAP 500 is a “bridged”
amplifier, so none of the speaker outlet sockets (+ or -)
is at earth potential. Avoid connecting mains powered
equipment such as electrostatic speakers, sub-woofers
and headphone energisers that do not have a floating
earth. No plug which is connected directly or indirectly to
earth potential should be attached to any speaker outlet
(+ or -).
28.2 Protectio n No t e s
In the NAP 500 the fan speed is increased in response to
an increase in amplifier dissipation. If the amplifier reaches
70°C due to prolonged running at high level or to airflow
being blocked, the output will be interrupted and the fan
will run at full speed until it has cooled down. This may
take a few minutes.
It is not necessary to switch the amplifier off, but it may
be advisable to mute the preamplifier or turn the volume
down to avoid surprises when it comes back on.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME LEVEL.
YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS THE CASE.
THE VOLUME SHOULD BE REDUCED.
E26
28.3 Loudspeaker Cable and Connectors
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS USED
TO CONNECT THE LOUDSPEAKERS.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
orientation at both the speaker and amplifier ends of the
cable is the same for both channels.
N A P 5 0 0 Power Amplifier
29 NAP 500 Connections
29.1 NAP 500 C o n n e c t e d t o NAP 5 0 0 P S
signal
input ch1
(L)
left
speaker
right
speaker
signal
input ch2(R)
mains input
and fuse
Input Ch1
ch1
Input Ch2
-ve
nc
cable
direction
marker
nc
-ve
ch2
Interconnect Cables
NAP 500PS Burndy
3 0 NAP 5 0 0 /NAP 5 0 0 PS Sp e c i f i c a t i o n
Power Output:
140 Watts per channel, 8Ω
700 VA Transient
Quiescent Consumption:
60VA
Voltage Gain:
+29dB
Input Impedance:
18kΩ
Frequency Response:
-3dB @ 1.5Hz and 100kHz
Dimensions (H x W x D):
NAP 500 - 160 x 432 x 375mm
NAP 500PS - 87 x 432 x 314mm
Weights:
NAP 500 - 25kg
NAP 500PS - 15.4kg
Mains Supply (NAP 500PS):
100-120V or 220-240V, 50/60Hz
E27
N A P 3 0 0 Power Amplifier
3 1 Installation and Operation
The NAP 300 and NAP 300PS should be installed on a dedicated equipment stand
intended for the purpose and should be in their final location before connecting cables or
switching on. Switch on the source and preamplifier components, with the volume turned
down, before switching on the NAP 300. The NAP 300 power button is located on the front
panel of the NAP 300PS Power Supply.
Care should be taken when siting the NAP 300 to ensure that the underside fan inlet and
rear outlet are not obstructed.
The NAP 300 and NAP 300PS are heavy and care should be taken when lifting or moving
them. Make sure that the surface they are to be placed on can support the full weight.
31.1 General C o n n e c t i o n s No t e s
The negative input and output connections for each
Only Naim Audio speaker cable should be used to
channel are common. The mains earth (ground) should
connect a loudspeaker to the output of the NAP 300.
always be connected regardless of what other equipment
Custom Naim Audio loudspeaker connectors are supplied
is used in conjunction with Naim power amplifiers. This only
to make the connection and in order to comply with
grounds the case and the electrostatic screen within the
current European safety regulations these should always
transformer, and is not connected to the signal negative. In
be used.
order to avoid hum loops, the signal negative of the whole
system should be connected to the mains earth (ground)
in one place.
31.2 Protectio n No t e s
In the NAP 300 the fan speed is increased in response to
an increase in amplifier dissipation. If the amplifier reaches
70°C due to prolonged running at high level or to airflow
being blocked, the output will be interrupted and the fan
will run at full speed until it has cooled down. This may
take a few minutes.
It is not necessary to switch the amplifier off, but it may
be advisable to mute the preamplifier or turn the volume
down to avoid surprises when it comes back on.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME LEVEL.
YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS THE CASE.
THE VOLUME SHOULD BE REDUCED.
E28
31.3 Loudspeaker Cable and Connectors
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS USED
TO CONNECT THE LOUDSPEAKERS.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
orientation at both the speaker and amplifier ends of the
cable is the same for both channels.
N A P 3 0 0 Power Amplifier
32 NAP 300 Connections
32 .1 NAP 300 C o n n e c t e d t o NAP 30 0 P S
signal
input ch1(L)
signal
input ch2(R)
right
speaker
left
speaker
mains input
and fuse
Input Ch1
ch1
Input Ch2
-ve
nc
cable
direction
marker
nc
-ve
ch2
Interconnect Cables
NAP 300PS Burndy
3 3 NAP 3 0 0 /NAP 3 0 0 PS Sp e c i f i c a t i o n
Power Output:
90 Watts per channel, 8Ω
500 VA Transient
Quiescent Consumption:
27VA
Voltage Gain:
+29dB
Input Impedance:
18kΩ
Frequency Response:
-3dB @ 2Hz and 70kHz
Dimensions (H x W x D):
Both - 87 x 432 x 314mm
Weights:
NAP 300 - 10.7kg
NAP 300PS - 14.1kg
Mains Supply (NAP 300PS): 100-120V or 220-240V, 50/60Hz
E29
N A P 2 5 0 Power Amplifier
3 4 Installation and Operation
The NAP 250 should be installed on a dedicated equipment stand intended for the
purpose and should be in its final location before connecting cables or switching on.
Switch on the source and preamplifier components, with the volume turned down, before
switching on the NAP 250. The NAP 250 power button is located on the front panel.
The NAP 250 is heavy and care should be taken when lifting or moving it. Make sure that
the surface it is to be placed on can support the full weight.
34.1 General C o n n e c t i o n s No t e s
The negative input and output connections are all
common. The mains earth should always be connected
regardless of what other equipment is used. This only
grounds the case and the electrostatic screen within the
transformer, and is not connected to the signal negative.
In order to avoid hum loops, the signal negative of the
whole system should be connected to the mains earth
(ground) in one place.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME LEVEL.
YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS THE CASE.
THE VOLUME SHOULD BE REDUCED.
34.3 Loudspeaker Cable and Connectors
Only Naim Audio speaker cable should be used to
connect a loudspeaker to the output of the NAP 250.
Custom Naim Audio loudspeaker connectors are supplied
to make the connection and in order to comply with
34.2 Protectio n No t e s
If the amplifier’s external case reaches 70°C due to
prolonged running at high power, the mains supply will be
interrupted and the illuminated logo will switch off until
current European safety regulations these should always
be used.
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS USED
the amplifier has cooled down. This may take up to thirty
TO CONNECT THE LOUDSPEAKERS.
minutes.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
35 NAP 250 Connections
orientation at both the speaker and amplifier ends of the
cable is the same for both channels.
35.1 NAP 250 Re a r
mains input
and fuse
left
speaker
right
speaker
signal input
ch1(L) & ch2(R)
Input
3 6 NAP 250 Specification
Power Output:
E30
80 Watts per channel, 8Ω
400 VA Transient
Quiescent Consumption:
25VA
Voltage Gain:
+29dB
Input Impedance:
18kΩ
Frequency Response:
-3dB @ 2Hz and 65kHz
Dimensions (H x W x D):
87 x 432 x 314mm
Weight
15.8kg
Mains Supply:
100-120V or 220-240V, 50/60Hz
-ve
ch1
ch2
N A P V 1 45 Power Amplifier
3 7 Installation and Operation
The NAPV 145 is a mono power amplifier intended for use in audio-visual systems. The
NAPV 145 should be installed on a dedicated equipment stand intended for the purpose
and should be in its final location before connecting cables or switching on. Switch on the
source and preamplifier components, with the volume turned down, before switching on
the NAPV 145. The NAPV 145 power button is located on the front panel.
The NAPV 145 is heavy and care should be taken when lifting or moving it. Make sure that
the surface it is to be placed on can support the full weight.
37 .1 General C o n n e c t i o n s No t e s
The negative input and output connections are all
common. The mains earth should always be connected
regardless of what other equipment is used. This only
grounds the case and the electrostatic screen within the
transformer, and is not connected to the signal negative.
In order to avoid hum loops, the signal negative of the
whole system should be connected to the mains earth
(ground) in one place.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME LEVEL.
YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS THE CASE.
THE VOLUME SHOULD BE REDUCED.
37.3 Loudspeaker Cable and Connectors
Only Naim Audio speaker cable should be used to
connect a loudspeaker to the output of the NAPV 145.
Custom Naim Audio loudspeaker connectors are supplied
to make the connection and in order to comply with
37 .2 Protectio n No t e s
If the amplifier’s external case reaches 70°C due to
prolonged running at high power, the mains supply will be
interrupted and the illuminated logo will switch off until
current European safety regulations these should always
be used.
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS USED
the amplifier has cooled down. This may take up to thirty
TO CONNECT THE LOUDSPEAKERS.
minutes.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
38 NAPV 145 Connections
orientation at both the speaker and amplifier ends of the
cable is the same for both channels.
38.1 NAPV 145 Rear
speaker
mains input
and fuse
signal input
3 9 NAPV 145 S pecification
Power Output:
Input
80 Watts, 8Ω
400 VA Transient
Quiescent Consumption:
15VA
Voltage Gain:
+29dB
Input Impedance:
18kΩ
Frequency Response:
-3dB @ 2Hz and 65kHz
Dimensions (H x W x D):
87 x 432 x 314mm
Weight
15.8kg
Mains Supply:
100-120V or 220-240V, 50/60Hz
-ve
i/p
nc
E31
N A P 2 0 0 Power Amplifier
4 0 Installation and Operation
The NAP 200 should be installed on a dedicated equipment stand intended for the
purpose and should be in its final location before connecting cables or switching on.
Switch on the source and preamplifier components, with the volume turned down, before
switching on the NAP 200. The NAP 200 power button is located on the front panel.
The NAP 200 can provide power for an appropriate Naim Audio preamplifier. The power
supply output is carried on the DIN input socket.
The NAP 200 is heavy and care should be taken when lifting or moving it. Make sure that
the surface it is to be placed on can support its full weight.
40.1 General C o n n e c t i o n s No t e s
The negative input and output connections are all
common. The mains earth should always be connected
regardless of what other equipment is used. This only
grounds the case and the electrostatic screen within the
transformer, and is not connected to the signal negative. In
order to avoid hum loops, the signal negative of the whole
system should be connected to the mains earth (ground)
in one place.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME LEVEL.
YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS THE CASE.
THE VOLUME SHOULD BE REDUCED.
40.3 Loudspeaker Cable and Connectors
Only Naim Audio speaker cable should be used to
connect a loudspeaker to the output of the NAP 200.
Custom Naim Audio loudspeaker connectors are supplied
to make the connection and in order to comply with
40.2 Protectio n No t e s
If the amplifier’s external case reaches 70°C due to
prolonged running at high power, the mains supply will be
interrupted and the illuminated logo will switch off until the
amplifier has cooled down. This may take up to thirty minutes.
current European safety regulations these should always
be used.
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS USED
TO CONNECT THE LOUDSPEAKERS.
Ensure when connecting speakers that they are “in
41 NAP 200 Connections
orientation at both the speaker and amplifier ends of the
41.1 NAP 200 Rear
mains input
and fuse
phase”. That is, the positive and negative connection
cable is the same for both channels.
left
speaker
right
speaker
signal input
ch1(L) & ch2(R) and
preamp power
supply
4 2 NAP 200 Specification
E32
Power Output:
70 Watts per channel, 8Ω
300 VA Transient
Quiescent Consumption:
11VA
Voltage Gain:
+29dB
Input Impedance:
18kΩ
Frequency Response:
-3dB @ 2Hz and 65kHz
Power Supply Output:
24V, 0.3A
Dimensions (H x W x D):
87 x 432 x 314mm
Weight
11.6kg
Mains Supply:
100-120V or 220-240V, 50/60Hz
Input/Preamp
Power Socket
ch1
24V
0.3A
ch2
-ve
N A P 1 5 0x Power Amplifier
4 3 Installation and Operation
The NAP 150x should be installed on a dedicated equipment stand intended for the
purpose and should be in its final location before connecting cables or switching on.
Switch on the source and preamplifier components, with the volume turned down, before
switching on the NAP 150x. The NAP 150x power button is located on the rear panel.
The NAP 150x can provide power for an appropriate Naim Audio preamplifier. The power
supply output is carried on the DIN input socket.
43 .1 General C o n n e c t i o n s No t e s
The negative input and output connections are all
common. The mains earth should always be connected
regardless of what other equipment is used. This only
grounds the case and the electrostatic screen within the
transformer, and is not connected to the signal negative.
In order to avoid hum loops, the signal negative of the
whole system should be connected to the mains earth
(ground) in one place.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME LEVEL.
YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS THE CASE.
THE VOLUME SHOULD BE REDUCED.
43.3 Loudspeaker Cable and Connectors
Only Naim Audio speaker cable should be used to
connect a loudspeaker to the output of the NAP 150x.
Custom Naim Audio loudspeaker connectors are supplied
to make the connection and in order to comply with
43 .2 Protectio n No t e s
If the amplifier’s external case reaches 70°C due to
prolonged running at high power, the mains supply will be
interrupted and the illuminated logo will switch off until
current European safety regulations these should always
be used.
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS USED
the amplifier has cooled down. This may take up to thirty
TO CONNECT THE LOUDSPEAKERS.
minutes.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
orientation at both the speaker and amplifier ends of the
44 NAP 150x Connections
cable is the same for both channels.
44.1 NAP 150x Rear
power
switch
mains input
left
and fuse speaker
4 5 NAP 150x S pecification
Power Output:
50 Watts per channel, 8Ω
250 VA Transient
Quiescent Consumption:
10VA
Voltage Gain:
+29dB
Input Impedance:
18kΩ
Frequency Response:
-3dB @ 3Hz and 50kHz
Power Supply Output:
24V, 0.25A
Dimensions (H x W x D):
70 x 432 x 301mm
Weight
7.5kg
Mains Supply:
100-120V or 220-240V, 50/60Hz
right
speaker
signal input
ch1(L) & ch2(R) and
preamp power
supply
Input/Preamp
Power Socket
ch2
-ve
ch1
24V
0.25A
E33
N A P V 1 75 Power Amplifier
4 6 Installation and Operation
The NAPV 175 is a three channel power amplifier intended for use in audio-visual systems.
The three channels provide power to drive a centre channel speaker and a pair of
either main front or surround channel speakers. Audio line level input is via two 4-pin DIN
sockets - one for the centre channel and one for the main or surround pair.
The NAPV 175 should be installed on an equipment rack intended for the purpose and
in its final location before connecting cables or switching on. Switch on the source and
preamplifier components, with the volume turned down, before switching on the NAPV
175. The power button is located on the rear panel.
The NAPV 175 is heavy and care should be taken when lifting or moving it. Make sure that
the surface it is to be placed on can support the full weight.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
46.1 General C o n n e c t i o n s No t e s
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME LEVEL.
The mains earth grounds only the case and the
electrostatic screen within the transformer and is not
connected to the signal negative. The mains earth must
always be connected to “ground” regardless of any other
equipment used. In order to avoid hum-loops the signal
negative of the whole system should be connected to the
mains earth in one place.
YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS THE CASE.
THE VOLUME SHOULD BE REDUCED.
46.3 Loudspeaker Cable and Connectors
Only Naim Audio speaker cable should be used to
connect a loudspeaker to the output of the NAPV 175.
Custom Naim Audio loudspeaker connectors are supplied
to make the connection and in order to comply with
46.2 Protectio n No t e s
current European safety regulations these should always
Once installed the NAP V175 is intended to remain
permanently powered up via its rear panel switch. If the
internal heatsink reaches 70°C due to prolonged running
at very high dissipation the mains supply will be interrupted
be used.
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS USED
and the illuminated logo will go off until the amplifier has
TO CONNECT THE LOUDSPEAKERS.
cooled down. This may take up to thirty minutes.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
47 NAPV 175 Connections
orientation at both the speaker and amplifier ends of the
cable is the same for all channels.
47.1 NAPV 175 Rear
power
switch
mains
input and
fuse
left
speaker
centre
speaker
right
speaker
signal input
ch1(L) &
ch2(R)
signal
input
centre
4 8 NAPV 175 S pecification
Power Output:
E34
50 Watts per channel, 8Ω
Channels:
Three
Quiescent Consumption:
10VA
Voltage Gain:
+29dB
Input Impedance:
18kΩ
Frequency Response:
-3dB @ 3Hz and 50kHz
Dimensions (H x W x D):
70 x 432 x 301mm
Weight
7.9kg
Mains Supply:
100-120V or 220-240V, 50/60Hz
Input Ch1 & Ch2
Input - Centre
nc
-ve
signal
nc
ch2
-ve
ch1
nc
N A P 6 - 5 0 Power Amplifier
4 9 Installation and Connection
The NAP 6-50 is a six channel power amplifier intended for use in multi-room audio
systems. The six channels are configured as three sets of two intended to drive one pair of
loudspeakers in three “zones”. Audio input for each zone is via 4-pin DIN sockets.
Care should be taken when siting the NAP 6-50 to ensure that the ventilation and fan
apertures are not obstructed. The NAPV 6-50 is heavy and care should be taken when
lifting or moving it. Make sure its installation support can carry its full weight.
Unused zone input sockets should be fitted with the
49.1 Operatio n
The NAP 6-50 is intended to remain permanently powered
via its front panel switch. When not in use it will drop into
“standby” mode. Standby mode is indicated by the
front panel logo illuminating red. Switch from standby
supplied yellow shorting plugs. Failure to use the shorting
plugs may reduce the reliability with which the NAP 6-50
drops into standby mode. Do not use the shorting plugs on
Naim equipment other than the NAP 6-50.
to operational mode takes place automatically when a
Naim Audio loudspeaker connectors are supplied. In order
signal is detected at any input or, alternatively, can be
to comply with current European safety regulations these
controlled via the 3.5mm “jack” trigger input socket.
should always be used.
49.2 General C o n n e c t i o n s N o t e s
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
The negative input and output connections within
orientation at both the speaker and amplifier ends of the
each zone are common but there is no signal negative
cable is the same for all channels.
connection between them. The mains earth grounds only
the case and the screen within the transformer and is not
49.3 Protection
connected to the signal negative. The mains earth must
The NAP 6-50 fan speed is increased automatically in
always be connected to “ground” regardless of any other
response to an increase in heat dissipation. If the internal
equipment used. In order to avoid hum-loops the signal
heatsink reaches 70°C due to prolonged running at very
negative of the whole system should be connected to the
high dissipation, blocked airflow, or fan failure, the mains
mains earth in one place.
supply will be interrupted and the illuminated logo will go
off until the amplifier has cooled down. This may take up to
50 NAP 6-50 Connections
50.1 NAP 6-50 Rear
mains input
and fuse
5 1 NAP 6-50 Specification
Power Output:
30 Watts per channel, 8Ω
Voltage Gain:
+29dB
Input Impedance:
18kΩ
Frequency Response:
-3dB @ 3Hz and 50kHz
Standby Consumption:
<1W
Trigger Input Voltage:
4.5V to 12V (plug tip +ve)
Dimensions (H x W x D):
87 x 432 x 314mm
Weight:
13.5kg
Mains Supply:
100-120V or 220-240V, 50/60Hz
thirty minutes.
zone 1
speaker
ch1, left
zone 2
speaker
ch1, left
zone 3
speaker
ch1, left
zone 1
speaker
ch2, right
zone 2
speaker
ch2, right
zone 3
speaker
ch2, right
trigger
input
input
zone 3 input
zone 2
input
zone 1
Signal Inputs
ch2
-ve
ch1
chassis
ground
E35
D e c l a r ations of Confor mity
5 2 Declaration of conformity to a p p r o p r i a t e s t a n d a r d s
Manufacturer
Naim Audio Limited, Southampton Road, Salisbury, England, SP1 2LN
Products
Preamplifiers - NAC 552, NAC 252, NAC 282, NAC 202, NAC 122x
Integrated Amplifiers - Supernait, NAIT 5i
Power Amplifiers - NAP 500/NAP 500PS, NAP 300/NAP 300PS, NAP 250, NAPV 145, NAP 200, NAP 150x, NAPV 175, NAP 6-50
Safety
EN 60065
EMC
Emissions Tested to:EN 55013 - Sound and television broadcast receivers and associated equipment
BS EN 61000-3-2: 2002 - Limits for harmonic current emissions (equipment input currents up to
and including 16 A per phase)
Immunity Tested to:EN55020 - Electromagnetic immunity of broadcast receivers and associated equipment
In accordance with:CISPR 16-1 - Radio disturbance and immunity measuring apparatus
CISPR 16-2 Methods of measurement of disturbances and immunity
IEC 801-2 8kV (air gap) 4kV (contact) (performance criterion B)
IEC 801-3 3V/m 20dB (performance criterion A)
IEC 801-4 1kV (AC lines) 0.5kV (signal lines) (performance criterion B)
Products that display the crossed-out wheeled bin logo
cannot be disposed of as domestic waste. These products
must be disposed of at facilities capable of re-cycling
them and appropriately handling any waste by-products.
Contact your local authority for details of the
nearest such facility. Appropriate recycling and
waste disposal helps conserve resources and
protects the environment from contamination.
E36