USER MANUAL - tridimas electronics

USER MANUAL - tridimas electronics
EP364
USER MANUAL
ALARM AND MANAGEMENT SYSTEM
User Manual v1.0
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
• DO NOT use the system where it can be interfere with other devices and cause any potential danger.
• DO NOT use the system with medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.
• DO NOT attempt to personally repair the system.
• System label is on the bottom side of the device.
Alarm system EP364 (also referenced as alarm system, system or device) is a device mounted in limited access areas. Any
system repairs must be done only by qualified, safety aware personnel.
The system must be powered by main 16-24V 50 Hz ~1.5A max or 18-24V
1,5A max DC power supply which must
be approved by LST EN 60950-1 standard and be easily accessible nearby the device. When connecting the power supply
to the system, switching the pole terminals places does not have any affect.
Any additional devices linked to the system EP364 (computer, sensors, relays etc.) must be approved by LST EN 60950-1
standard.
Main power supply can be connected to AC mains only inside installation room with
automatic 2-pole circuit breaker capable of disconnecting circuit in the event of short
circuit or over-current condition. Open circuit breaker must have a gap between connections of more than 3mm and the disconnection current 5A.
Phase
Null
PE
AC/DC
AC 230V
50 Hz/DC 24V
EP364
USB cable
Mains power and backup battery must be disconnected before any installation or tuning work starts. The system installation or maintenance must not be done during stormy conditions.
Backup battery must be connected via the connection which in the case of breaking would result in disconnection of one
of battery pole terminals. Special care must be taken when connecting positive and negative battery terminals. Switching
the pole terminals places is NOT allowed.
In order to avoid fire or explosion hazards the system must be used only with approved backup battery.
The device is fully turned off by disconnecting 2-pole switch off device of the main power supply and disconnecting
backup battery connector.
Fuse F1 type – Slow Blown 3A. Replacement fuses have to be exactly the same as indicated by the manufacturer.
If you use I security class computer for setting the parameters it must be connected to earth.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that the
product must not be disposed of together with household waste. To prevent possible harm to human health and/or the environment, the product must be disposed on in an approved and environmentally safe recycling process. For further information on how
to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste disposal in your area.
Limited Liability
The buyer must agree that the system will reduce
the risk of fire, theft, burglary or other dangers but
does not guarantee against
such events.
“ELDES UAB” will not take any responsibility regarding personal or property or revenue loss
while using the system. “ELDES UAB” liability according to local laws does not exceed value of the
purchased system. “ELDES UAB” is not affiliated
with any of the cellular providers therefore is not
responsible for the quality of cellular service.
Manufacturer Warranty
The system carries a 24-month warranty by the
manufacturer “ELDES UAB”. Warranty period starts
from the day the system has been purchased
by the end user. The warranty is valid only if the
system has been used as intended, following all
guidelines listed in the manual and within specified operating conditions. Receipt must be kept as
a proof of purchase date.
The warranty is voided if the system has been
exposed to mechanical impact, chemicals, high
humidity, fluids, corrosive and hazardous environments or other force majeure factors.
Technical Support
If you require more detailed information on your
system or in case of system failure occurrence,
please, contact your alarm system installer.
About User Manual
Contents
1. General Information...................................................................... 4
1.1 1.2 1.3 1.4 Short Description of Main Definitions................................................4
EKB2 Keypad Overview............................................................................4
EKB3/EKB3W Keypad Overview............................................................6
Partitions.......................................................................................................6
2. Technical Specifications................................................................ 7
2.1 2.2 2.3 Electrical & Mechanical Characteristics..............................................7
Main Unit, LED & Connector Functionality.......................................8
Wiring Diagrams.........................................................................................9
2.3.1 General Wiring.............................................................................9
2.3.2 Zone Connection Types............................................................9
3. Basic Configuration & Use...........................................................10
3.1 Setting Up Date & Time......................................................................... 10
3.2. Arming, Disarming the System & Turning Off the Alarm.......... 11
3.2.1 Arm by EKB2 Keypad.............................................................. 11
3.2.2 Disarm & Turn off the Alarm by EKB2 Keypad............... 12
3.2.3 Arm by EKB3/EKB3W Keypad.............................................. 12
3.2.4 Disarm & Turn off the Alarm by EKB3/EKBW Keypad.. 13
3.2.5 Arm by iButton® Key............................................................... 13
3.2.6 Disarm & Turn off the Alarm by iButton® Key................ 13
3.2.7 Arm by EWK1 – Wireless Key-fob........................................ 14
3.2.8 Disarm & Turn off the
Alarm by EWK1 – Wireless Key-fob.................................... 14
3.3 Activating STAY Mode........................................................................... 15
3.3.1 Arm by EKB2 Keypad in STAY Mode Manually............... 15
3.5 Bypassing & Activating Zones............................................................ 16
3.4 Alarm Indications & Viewing Violated Zones / Tampers............ 16
3.6 View Temperature................................................................................... 17
3.7 Trouble Indications................................................................................. 17
This document describes basic configuration and
usage of alarm system EP364. It is very impor­tant
to read the user manual before starting to use the
system.
NOTE: For complete system configuration and
control, please refer to EP364 installation manual located at www.eldes.lt/en/download
Copyright © “ELDES UAB”, 2012. All rights reserved
It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authorization
by “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby,
“ELDES UAB” declares that this alarm and management system EP364 is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt
1. General Information
EP364 is an alarm system for private houses, cottages, village houses, garages, warehouses and other buildings, also capable of
turning on/off the electrical appliances by alarm system keypad. This alarm system provides a simple thus effective way of use.
The system may consist of:
• EP364 alarm system device.
• Up to 4 EKB2/EKB3 wired keypads.
• Up to 4 EKB3W wireless keypads.
• Wired and/or wireless detection devices: movement sensors, magnetic door contacts, smoke sensors etc.
• Other devices: indoor/outdoor sirens, zone/PGM output expansion modules, heating, lighting, gates etc.
For more details on EP364 system, please, consult with your alarm system installer.
1.1 Short Description of Main Definitions
The following table provides the explanation of main definitions which are met in this user manual.
Definition
Description
System; alarm system
EP364 device
Keypad
Device with a set keys allowing to configure & control the system, view violated zones & system troubles
EKB2
Model of wired LCD keypad
EKB3
Model of wired LED keypad
EKB3W
Model of wireless LED keypad
User password
4-digit combination intended for system arming/disarming using a keypad
iButton® key
Small metal tab containing a unique ID code intended for system arming/disarming
Zone
Alarm system input for wired and wireless sensor connection
PGM output
Alarm system output for connection of electrical appliances (heating, lighting, gates etc.)
Partition
Section dividing one alarm system into two or more independent parts software-wise
1.2 EKB2 Keypad Overview
EKB2 is an LCD keypad intended for using with EP364 alarm system.
Temperature
Keys Functionality
Digital Clock
One menu level back / cancel
Menu navigation – up
Menu navigation – down
Confirm (enter) value
...
Value typing
Keypad partition switch / minus
symbol for entering negative
temp. value
Additional menu / minus symbol
for entering negative temp. value
4
20,20C
System Status
Message
System
Trouble
Indication
Custom
Keypad
Partition
Title
STAY
BYP
TBL
ready
GARAGE
00:45
Home Screen
View
Bypass Mode
Indication
Stay Mode
Indication
Fig. No. 1
Main Messages & Icons
Icon / Message
Description
Delay zone violated when system is disarmed.
Exit delay countdown initiated.
System is armed and menu is locked.
System is disarmed and menu is unlocked
Icon / Message
24H zone violated.
FIRE ALARM
Fire zone violated.
TAMPER ALARM
READY
NOT READY
ARMED
+ CONFIGURATION
MODE
BURGLARY ALARM
Configuration Mode activated.
Delay, Instant or Follow zone violated when
system is armed.
Description
24 ALARM
Tamper violated
System is ready to be armed.
System is not ready to be armed – one or more
zones / tampers violated.
System is armed (optional feature).
STAY
Stay mode activated
BYP
One or more zones bypassed
TBL
One or more system troubles are present
EKB2 LCD screen is intended for displaying alarm system status messages and alerts. Message READY is displayed on the screen that
no zones are violated or no troubles are present and the system is prepared for arming. Message NOT READY (and TBL) shows up in
case of zone violation or if system troubles are present. The alarm system cannot be armed until the troubles are removed or violated
zone (-s) is restored, bypassed or set up to operate under Force mode. The following troubles allow system arming when present:
•
main power supply is lost.
•
low battery.
•
battery dead or missing.
•
battery failed.
•
siren failed.
•
date/time not set.
Audio Indication
The built-in buzzer uses two types of sound signals – three short beeps and one long beep. Three short beeps stand for successfully
carried out configuration command, one long beep – for invalid configuration command. In addition, the buzzer continuously emits
short beeps in case of alarm and during exit/entry delay.
Visual Indication
EKB2 can be used even in dark premises as the LCD screen and keys are illuminated continuously. In case of alarm the keypad illumination level is boosted and stays in this state until the system is disarmed. The illumination level lowers down in 3 minutes after the last
key-touch while the system is disarmed.
MANUAL ELDES EP364 V1.0
5
1.3 EKB3/EKB3W Keypad Overview
EKB3/EKB3W is a LED keypad intended for using with EP364 alarm system.
LED Functionality
ARMED
Alarm system is armed /Configuration mode
READY
System is prepared for arming
SYSTEM
System troubles / valid command is being entered
BYPS
Zone bypass mode
1-12
Violated zone
A
B
ARMED
READY
SYSTEM
1
BYPS
7
8
2
9
3
4
5
6
10
11
12
1
2
3
STAY
4
5
6
BYPS
7
8
9
INST
*
0
#
CODE
Fig. No. 2
Keys Functionality
[BYPS]
Zone bypass mode
[CODE]
Additional options - system trouble list / violated high zone indication / violated tamper indication
[*]
Configuration Mode (when typed as a 1st character) / cancel command (when typed as a 2nd character) / keypad
partition switch (if enabled)
[#]
Confirm (enter) command
[0] ... [9]
Command typing
[STAY]
Manual Stay mode activation
[INST]
(currently inactive)
The green indicator READY indicates that no zones are violated or no troubles are present and the system is prepared for arming.
Yellow indicator SYSTEM lights up or flashes in case of zone violation or if system troubles are present. The alarm system cannot be
armed until the troubles are removed or violated zone (-s) is restored, bypassed or set up to operate under Force mode. The following
troubles allow system arming when present:
•
main power supply is lost.
•
low battery.
•
battery dead or missing.
•
battery failed.
•
siren failed.
•
date/time not set.
Audio Indication
The built-in buzzer uses two types of sound signals – three short beeps and one long beep. Three short beeps stand for successfully
carried out configuration command, one long beep – for invalid configuration command. In addition, the buzzer continuously emits
short beeps in case of alarm and during exit/entry delay.
Visual Indication
EKB3 keys have a LED back-light, therefore it is possible to use this keypad even in dark premises. In case of alarm the keypad backlight turns on and lasts until the system is disarmed. The back-light lasts for 3 minutes after the last key-stroke while the system is
disarmed.
Due to battery power saving reasons the EKB3W keypad back-light and LED light last for 10 seconds after the last key-stroke. However,
this duration is configurable.
1.4 Partitions
Your alarm system may be divided into up to 4 partitions: Partition 1 - Partition 4 . Each system partition operates independently
from each other, therefore dividing the system into partitions allows to use 1 alarm system unit to secure up to 4 different areas, for
example: office and warehouse, house and garage etc. By default configuration, the system is NOT divided into partitions and all user
phone numbers, user passwords, keypads, iButton® keys, zones are assigned to Partition 1.
6
2. Technical Specifications
2.1 Electrical & Mechanical Characteristics
Electrical & Mechanical Characteristics
Main Power Supply
Current in Standby without External Sensors and Keyboard
Recommended Backup Battery Voltage, Capacity
Recommended Backup Battery Type
Maximum Battery Charge Current
Number of Zones on Board
Nominal Zone Resistance
Number of PGM Outputs on Board
EP364 PGM Output Circuit
16-24V 50 Hz ~1.5A max / 18-24V
Up to 80mA
12V; 1,3-7Ah
Lead-Acid
900mA
6 (ATZ mode: 12)
5,6kΩ (ATZ Mode: 5,6kΩ and 3,3kΩ)
4
Maximum Commuting PGM Output Values
BELL: Siren Output when Activated
BELL: Maximum Siren Output Current
BELL: Maximum Cable Length for Siren Connection
BELL: Cable Type for Siren Connection
AUX: Auxiliary Equipment Power Supply Voltage
AUX: Maximum Accumulative Current of Auxiliary Equipment
AUX: Maximum Cable Length for Auxiliary Equipment Connection
AUX: Cable Type for Auxiliary Equipment Connection
BUZ: Maximum Current of Mini Buzzer
BUZ: Power Supply Voltage of Mini Buzzer
BUZ: Cable Type for Mini Buzzer Connection
Dimensions
Operating Temperature Range
Supported Temperature Sensor Model
Maximum Supported Number of Temperature Sensors
DATA: Maximum Cable Length for 1-Wire® Communication
DATA: Cable Type for 1-Wire® Communication
Supported iButton® Key Model
Maximum Supported Number of Keyboards
Y/G: Maximum Cable Length for RS485 Communication
Y/G: Cable Type for RS485 Communication
MIC: Maximum Cable Length for Microphone Connection
MIC: Cable Type for Microphone Connection
Voltage – 30V; Current – 100mA;
Connected to COM
1A
up to 30 meters
Unshielded
13,8V DC
1,1A
up to 100 meters
Unshielded
150mA
5V DC
Unshielded
140x100x18mm
-20...+550C
Maxim®/Dallas® DS18S20, DS18B20
8
up to 30 meters
Unshielded
Maxim®/Dallas® DS1990A
4 x EKB2 / EKB3
up to 100 meters
Unshielded
Up to 2 meters
Unshielded
Wireless Transmitter-Receiver Frequency
868 Mhz
Wireless Communication Range
Maximum Supported Number of Wireless Devices
Event Log Size
Maximum Supported Number of Zones
Maximum Supported Number of PGM Outputs
Cable Type for Zone and PGM Output Connection
Communications
Supported Protocols
Up to 30m in premises; up to 150m in open areas
32
500 events
76
76
Unshielded
PSTN
Ademco Contact ID®, 4+2
MANUAL ELDES EP364 V1.0
1R
OUT
1,5A max
Open Collector Output.
Output is pulled to COM
when turned ON.
7
2.2 Main Unit, LED & Connector Functionality
STAT
C4
C3
C2
C1
Main Unit Functionality
DEF
Pins for restoring default settings
USB
Mini USB port
FUSE F1
3A fuse
W-LESS ANT
Wireless antenna SMA type connector
MODULES*
Slots for EA1, EA2 or EPGM8 module
W-LESS ANT
C4 C3
DEF
MODULES
C2
PGM output C2 status - on/off
C3
PGM output C3 status - on/off
C4
PGM output C4 status - on/off
STAT
Micro-controller status
AKU+
AKU-
AC/DC
AC/DC
AUX+
AUXBELL+
BELLCOM
G
Y
C2
C1
BUZ+
BUZMIC+
MIC+5V
DATA
COM
Z6
COM
Z5
PGM output C1 status - on/off
Z4
COM
Z3
Z2
COM
Z1
C1
TIP RING
LED Functionality
Fig. No.3
Connector Functionality
TIP
PSTN (landline) terminal
RING
PSTN (landline) terminal
DATA
1-Wire® interface for iButton® key & temperature sensor connection
+5V
Temperature sensor power supply terminal (+5V)
MIC-
Microphone negative terminal
MIC+
Microphone positive terminal
BUZ-
Mini buzzer negative terminal
BUZ+
Mini buzzer positive terminal
C1 - C4
PGM output terminals
Z1 - Z6
Security zone terminals
Y
RS485 interface for communication (yellow wire)
G
RS485 interface for communication (yellow wire)
COM
Common return terminal
BELL-
Siren negative terminal
BELL+
Siren positive terminal
AUX-
Negative power supply terminal for auxiliary equipment
AUX+
Positive power supply terminal for auxiliary equipment
AC/DC
Main power supply terminals
AKU-
Backup battery negative terminal
AKU+
Backup battery positive terminal
8
FUSE F1
3A
PRG
USB
2.3 Wiring Diagrams
2.3.1 General Wiring
AKU+
AKU-
Backup Battery
12V 1.3-7Ah
AC/DC
AC/DC
AUX+
AUXBELL+
BELLCOM
G
Y
C2
C1
BUZ+
BUZMIC+
MIC+5V
DATA
COM
Z6
COM
Z5
Z4
COM
Z3
Z2
COM
Z1
Metal box
PE contact
Fuse 500 mA
~16-24V
Z6
5.6k
5.6k
5.6k
5.6k
5.6k
Z5
Z4
Z3
Z2
Z1
BUZ
MIC
SIREN/BELL
Fig. No. 4
~230V 50Hz
EPGM1
1A max.
iButton®
key reader
Relay
module
EKB3
Temperature sensor
EKB2
2.3.2 Zone Connection Types
Type 1
Normally open contact
with 5,6KΩ end of line
resistor
Type 2
Normally closed contact with 5,6KΩ end of
line resistor
Type 3
Tamper and 5,6KΩ
end of line resistor
and 3,3KΩ end of line
resistor with normally
closed contact
Type 4
Type 5
ATZ Mode: 5,6KΩ end
of line resistor and normally closed contact
with 3,3KΩ end of line
resistor and normally
closed contact
ATZ Mode: Tamper,
5,6KΩ end of line
resistor, 5,6KΩ end of
line resistor with normally closed contact
and 3,3KΩ end of line
resistor with normally
closed contact.
Fig. No. 5
MANUAL ELDES EP364 V1.0
9
3. Basic Configuration & Use
ATTENTION: System configuration described in this chapter is based on default system parameter values. Your alarm system
installer may have changed those values. For more details, please, contact your alarm system installer.
This chapter provides a description of basic configuration and use of EP364 alarm system by the following methods:
•
EKB2 keypad.
•
EKB3 keypad.
•
EKB3W keypad.
•
iButton® key.
EKB2
EKB3/
EKB3W
The system configuration and control by EKB2 keypad is performed by navigating throughout the menu section list displayed on LCD screen. To navigate in the menu path, touch ↓, ↑ keys to select the desired menu section and touch OK key
to open the selected section. To enter a required value, use 0... 9 keys and touch OK key for value confirmation or cancel/
go one menu section back by touching ←key. The value can be typed in directly by touching 0... 9 keys while highlighting
the desired menu section. EKB2 menu type is “circle”, therefore when the last section in the menu list is selected, you will
be brought back to the beginning of the list after touching the ↓ key. In this user manual, the menu path is provided under
“tree” view by starting at home screen view. In this user manual valid parameter range is indicated in brackets..
The system configuration and control by EKB3/EKB3W keypad is performed by entering a valid configuration command
using the number keys 0... 9 and [#] key for confirmation. Some commands require [BYPS], [CODE] and [STAY] keys as well.
The structure of standard configuration command is a combination of digits. In this user manual, valid parameter range
is indicated in brackets.
3.1 Setting Up Date & Time
NOTE: When the alarm system is connected to a monitoring station the date and time are set automatically. The system retrieves this data from the monitoring station by itself.
EKB2
Navigate through the following menu path using OK and arrow keys and
enter the date and time values using the number keys:
Menu path:
OK → DATE/TIME SET → OK → yyyy-mm-dd_hr:mn → OK
Value: yyyy – year; mm – month, range – [01... 12]; dd – day, range - [01... 31]; hr – hours,
range – [00... 23], mn – minutes, range – [00... 59].
Example: 2011-12-15 13:45
10
3.2 Arming, Disarming the System & Turning Off the Alarm
Before arming the system it is necessary to close all doors and windows in the secured area and move yourself away from the movement detection field.
Don’t stand in
movement sensor
detection zone
Close all
doors
Close all
windows
Close all
doors
Fig. No. 5
3.2.1 Arm by EKB2 Keypad
EKB2
1. To arm the system, enter any out of 30 available 4-digit user passwords using the number keys:
1
2
3
4
5
6
7
8
9
0
Enter user password (and select partition):
If only 1 partition is enabled: uuuu → OK →
If more than 1 partition is enabled: uuuu → OK → [p] part-name → OK
Fig. No. 10
Value: uuuu – 4-digit user password; p – partition number, range – [1... 4], part-name – up to 15 characters
partition name.
Example: 1111 → OK → [2] PART2 → OK
2. The system will initiate the exit delay countdown (by default – 15 seconds) intended for user to leave the secured area. The exit delay is indicated by short beeps emitted by keypad buzzer, buzzer connected to the alarm
system (if any) and
icon displayed next to the countdown timer on EKB2 keypad screen.
3. When the system is successfully armed, the keypad will display
to home screen view.
icon on the screen for 5 seconds and switch
4. The system will not allow to arm the system, when one or more zones / tampers are violated. For more details,
please refer to chapter 3.5 Bypassing & Activating Zones.
MANUAL ELDES EP364 V1.0
11
3.2.2 Disarm & Turn off the Alarm by EKB2 Keypad
EKB2
1. The system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the
secured area. Entry delay countdown is intended for user to enter a valid user password before the alarm is
caused. The countdown is indicated by short beeps emitted by keypad buzzer and by long steady beep emitted by buzzer connected to the alarm system (if any).
2. To disarm the system or turn off the alarm, enter any out of 30 available 4-digit user passwords using the number keys:
1
2
3
4
5
6
7
8
9
0
Enter user password (and select partition):
If only 1 partition is enabled: uuuu → OK →
If more than 1 partition is enabled: uuuu → OK → [p] part-name → OK
Fig. No. 6
Value: uuuu – 4-digit user password; p – partition number, range – [1... 4], part-name – up to 15 characters partition
name.
Example: 1111 → OK → [2] PART2 → OK
3. When the system is successfully armed and if:
•
only 1 partition is enabled, the keypad will display
home screen view.
icon on the screen for 5 seconds and switch to
•
more than 1 partition is enabled, the keypad will display part-name DISARMED message on the screen for
3 seconds and switch to partition selection menu.
3.2.3 Arm by EKB3/EKB3W Keypad
EKB3/
EKB3W
1. To arm the system, enter any out of 30 available 4-digit user passwords using the number keys:
1
2
3
4
5
6
7
8
9
0
Enter user password:
uuuu
Value: uuuu – 4-digit user password
Example: 1111
Fig. No. 7
2. The system will initiate the exit delay countdown (by default – 15 seconds) intended for user to leave the secured area. The countdown is indicated by short beeps provided by keypad built-in buzzer (if any).
3. When the system is successfully armed, EKB3/EKB3W red indicator ARMED will light ON.
4. The system will not allow to arm the system, when one or more zones / tampers are violated. For more details, please
refer to chapter 3.5 Bypassing & Activating Zones.
12
3.2.4 Disarm & Turn off the Alarm by EKB3/EKBW Keypad
EKB3/
EKB3W
1. The system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the
secured area. Entry delay countdown is intended for user to enter a valid user password before the alarm is
caused.
2. To disarm the system or turn off the alarm, enter any out of 30 available 4-digit user passwords using the
number keys:
1
2
3
4
5
6
7
8
9
0
Enter user password:
uuuu
Value: uuuu – 4-digit user password
Example: 1111
Fig. No. 8
3. When the system is successfully armed, EKB3/EKB3W red indicator ARMED will light OFF.
3.2.5 Arm by iButton® Key
1. To arm the system, touch the iButton® key reader by any out of 5 iButton® keys:
Fig. No. 9
2. The system will initiate the exit delay countdown (by default – 15 seconds) intended for user to leave the
secured area. The countdown is indicated by short beeps provided by EP364 buzzer (if any).
3. The system will not allow to arm the system, when one or more zones / tampers are violated. For more details, please
refer to chapter 3.5 Bypassing & Activating Zones.
3.2.6 Disarm & Turn off the Alarm by iButton® Key
1. The system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the secured
area. Entry delay countdown is intended for user to enter a valid user password before the alarm is caused.
2. To disarm the system or turn off the alarm, touch the iButton® key reader by any out of 5 iButton® keys:
Fig. No. 10
MANUAL ELDES EP364 V1.0
13
3.2.7 Arm by EWK1 – Wireless Key-fob
EWK1
1. To arm the system, press 1 out of 4 EWK1 buttons (by default –
button) assigned to arm the alarm system.
Arm the
system
Fig. No. 11
2. The system will initiate the exit delay countdown (by default – 15 seconds) intended for user to leave the secured area.
3. The system will not allow to arm the system, when one or more zones / tampers are violated. For more details, please
refer to chapter 3.5 Bypassing & Activating Zones.
3.2.8 Disarm & Turn off the Alarm by EWK1 – Wireless Key-fob
EWK1
1. The system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the secured area. Entry delay countdown is intended for user to enter a valid user password before the alarm is caused.
2. To disarm the system or turn off the alarm, press 1 out of 4 EWK1 buttons (by default –
disarm the alarm system
Disarm the
system
Fig. No. 12
14
button) assigned to
3.3 Activating STAY Mode
EKB2
EKB3/
EKB3W
EWK1
Stay mode allows the user to remain in the secured area after arming the system. In Stay mode, the system does not
cause the alarm when the zones, set up to operate under this mode, become violated. This mode is usually used
when arming the system before night.
There are two ways to activate Stay mode:
•
Automatic - This mode is activated automatically in case the user does not leave the secured area (if delay zone
is not violated and restored) during exit delay countdown when arming the system.
•
Manual - The system goes into Stay mode after the user opens an additional menu or presses [STAY] key and
enters a valid user password by EKB2 and EKB3/EKB3W keypad respectively.
There is no exit delay countdown when activating Stay mode manually.
Stay mode status is indicated in the home screen view of EKB2.
NOTE: Delay Zone Becomes Instant in Stay Mode feature may be enabled on your system. In that case the alarm will be
caused instantly instead of entry delay countdown being initiated if a delay zone becomes violated while the system
is operating in Stay mode. For more details, please, contact your alarm system installer.
3.3.1 Arm by EKB2 Keypad in STAY Mode Manually
EKB2
1. Navigate through the following menu path using P2 and arrow keys and enter a valid user password using the
number keys to arm the system in Stay mode manually:
Menu path:
If only 1 partition is enabled: P2 → uuuu → OK
If more than 1 partition is enabled: P2 → uuuu → OK → [p] part-name → OK
Value: uuuu - 4-digit user password
2. When the system is successfully armed and if:
•
only 1 partition is enabled, the keypad will display icon on the screen for 5 seconds and switch to home
screen view where STAY message will be indicated.
•
more than 1 partition is enabled, the keypad will display part-name DISARMED message on the screen
for 3 seconds and switch to partition selection menu.
For more details on how to disarm & turn off the alarm by EKB2 keypad, please refer to chapter 3.2.5 Disarm & Turn off
the Alarm by EKB2 Keypad.
MANUAL ELDES EP364 V1.0
15
3.3.2 Arm by EKB3/EKB3W Keypad in STAY Mode Manually
EKB3/
EKB3W
1. Arm the system in Stay mode manually by entering the following combination using [STAY] and number keys:
Press the [STAY] key & enter user password:
STAY uuuu
Value: uuuu - 4-digit user password
Example: STAY1111
For more details on how to disarm & turn off the alarm by EKB3/EKB3W keypad, please refer to chapter 3.2.7 Disarm &
Turn off the Alarm by EKB3/EKB3W Keypad.
3.4 Alarm Indications & Viewing Violated Zones / Tampers
EKB2
EKB3
The built-in EKB2 buzzer and EP364 buzzer (if any) provide short beeps continuously in case of alarm. In addition, the
LCD screen back-light level is boosted and the alarm message (depending on violated zone type or tamper violation)
is displayed in the main screen view of EKB2 screen. The buzzer can be silenced by disarming the system using any
method. Navigate through the following menu path using OK and arrow keys to view the violated zone or tamper
number:
Menu path:
OK → VIOLATED ZONES → OK → ZONE 1... 76
View violated zone:
View violated tamper:
OK → VIOLATED TAMPERS → OK → TAMPER 1... 76
The built-in EKB3/EKB3W buzzer emits short beeps continuously and EP364 buzzer (if any) emits a steady beep in case
of alarm. In addition, the violated zone number is indicated by illuminated zone LED or flashing indicator SYSTEM (if
the violated zone number is above 12). The violated tamper number is indicated by illuminated indicator SYSTEM. The
buzzer can be silenced by disarming the system using any method.
For more details on EKB3/EKB3W violated high-numbered zone & tamper number indication, please refer to chapter 3.10
Trouble Indications.
By default configuration, the siren/bell (if any) provides continuous alarm sound for 1 minute in case of alarm. The fire
alarm is indicated by pulsating siren/bell alarm sound. The alarm sound can be silenced by disarming the system using
anymethod.
3.5 Bypassing & Activating Zones
Arming the system is disabled while there’s at least 1 violated zone. Bypassing allows to temporally deactivate a certain violated zone
and arm the alarm system after-wards.
EKB2
Navigate through the following path using OK and arrow keys to bypass a violated zone (-s):
Menu path:
OK → BYPASS → OK → BYPASS LIST 1... 3 → OK → ZONE 1... 76 → OK → BYPASS → OK
Bypass a zone:
OK → BYPASS → OK → BYP VIOLATED ZONES → OK
Bypass all zones:
Navigate through the following path using OK and arrow keys to activate a bypassed zone:
Menu path:
Activate a bypassed zone: OK → BYPASS → OK → BYPASS LIST 1... 3 → OK → ZONE 1... 76 → OK → UNBYPASS → OK
NOTE: Zones can only be bypassed and activated when the system is not armed.
16
EKB3/
EKB3W
Bypass a violated zone by entering the following combination using [BYPS], number and [#] keys:
Press the [BYPS] key, enter zone number & user password:
BYPS nn uuuu #
Value: nn – zone number, range – [01... 76]; uuuu – 4-digit user password.
Example: BYPS051111#
NOTE: The zone will stay bypassed until the system is disarmed. Once the system is disarmed, the zone‘s current state will be
indicated on the keypads.
ATTENTION: Bypassing a violated tamper is NOT allowed. Please, restore the tamper (for example: close sensor‘s enclosure)
before arming the system
3.6 View Temperature
EKB2
Navigate through the following path using OK and arrow keys to view real-time temperature sensor values:
Menu path:
OK → TEMP SENSORS INFO → OK → 1... 8
3.7 Trouble Indications
EKB2
Message TBL displayed in the lower left side of the home screen view indicates presence of system troubles.
In order to find out more on the particular system problem please , open menu section TROUBLES. The description on
each system problem is indicated in the table below.
Menu path:
OK → TROUBLES → OK → [TROUBLE]
Name
Description
MAIN POWER LOSS
Main power supply is lost
LOW BATTERY
Backup battery voltage is 10.5V or lower
BATTERY DEAD/MISS
Backup battery is not present or the battery voltage runs below 5V
BATTERY FAILED
Backup battery resistance is 2Ω or higher
SIREN FAILED
Siren is disconnected/broken
VIOLATED TAMPER
One or more tampers are violated
DATE/TIME NOT SET
Date/time not set
MANUAL ELDES EP364 V1.0
17
EKB3/
EKB3W
Yellow LED SYSTEM indicates system troubles. SYSTEM LED indications are mentioned in the table below.
SYSTEM LED
Description
Illuminated continously
One ore more zones or tampers are violated; other
system troubles
Flashing
One or more high-numbered zones are violated
In order to find out more on the particular system problem please , enter command A. After this procedure the system
will activate red zone LEDs for 15 seconds. The description on each LED indication is mentioned in the table below.
Zone LED
Description
1
Main power supply is lost
2
Backup battery voltage is 10.5V or lower
3
Backup battery is not present or the battery voltage runs below 5V
4
Backup battery resistance is 2Ω or higher
5
Siren is disconnected/broken
7
One or more tampers are violated
8
Date/time not set
10
One or more high-numbered zones (Z13 - Z76) are violated
In order to find out which particular high zone is violated please , enter command B.
In order to find out which particular tamper is violated please , enter command C.
A. System trouble indication - enter command:
[CODE#]
B. Violated high zone indication – enter command:
[CODE1]
C. Violated tamper indication – enter command:
[CODE2]
The number of violated high zone or tamper can be calculated using the table below according to the formula: number
from zone LED section B + number from zone LED section A.
Example: LED #3 from section A is flashing and LED #8 from section B is illuminated continuously. According to the table
below LED #8 is equal to number 18, therefore 18 + 3 = 21.
Result: Violated high zone or tamper number is 21.
18
Zone LED section - A
(flashing)
Zone LED section - B
(illuminated continously)
Zone LED 1 = 1
Zone LED 7 = 12
Zone LED 2 = 2
Zone LED 8 = 18
Zone LED 3 = 3
Zone LED 9 = 24
Zone LED 4 = 4
Zone LED 10 = 30
Zone LED 5 = 5
Zone LED 11 = 36
Zone LED 6 = 6
Zone LED 12 = 42
MANUAL ELDES EP364 V1.0
19
Made in Lithuania.
www.eldes.lt
iButton is a registered trademark of Maxim Integrated Products, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement